Owner`s manual | FUNAI CIWL3706 Flat Panel Television User Manual

OWNER'S MANUAL
CIWL3706
37 INCH
ANALOG / DIGITAL
LCD TELEVISION
HIGH-DEFINITION TELEVISION
TO RECEIVE ANALOG/DIGITAL SIGNAL
YOU MUST CONNECT ANTENNA.
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-474-0045,
OR VISIT OUR WEB SITE AT http://www.funai-corp.com
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT WITHIN
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELEC-
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
TRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The important note is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions should
be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss of an
authorization code for a CATV converter, is not intended to be
unplugged by the user for cleaning or any other purpose, may exclude
the reference to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by the
TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold
with the TV.
PORTABLE CART WARNING
Any mounting of the appliance should follow
the manufacturer’s instructions and should use
a mounting accessory recommended by the
manufacturer. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination to
S3126A
overturn.
9. VENTILATION - Slots and openings in the
cabinet and the back or bottom are provided for ventilation and to
ensure reliable operation of the TV and to protect it from overheating,
these openings must not be blocked or covered. The openings should
never be blocked by placing the TV on a bed, sofa, rug, or other similar
surface. This TV should never be placed near or over a radiator or heat
register. This TV should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your appliance dealer
or local power company. For TVs intended to operate from battery
power, or other sources, refer to the operating instructions.
2
EN
11. GROUNDING OR POLARIZATION - This TV is equipped with a polarized alternating-current line plug(a plug having one blade wider than
the other). This plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or cable
system is connected to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. (Fig. A)
14. LIGHTNING - For added protection for this TV receiver during a lightning
storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV due to lightning and power-line surges.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
d. If the TV does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating
instructions, as improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the TV to its normal operation.
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this indicates
a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be sure the
service technician uses replacement parts specified by the manufacturer that
have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this TV,
ask the service technician to perform routine safety checks to determine
that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
PRECAUTIONS
•
•
•
•
Place your TV in a room with adequate ventilation.
Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.
Do not place your TV on soft surfaces, such as rugs or blankets.
Leave enough room for air to circulate around the bottom, top and back of the set.
IMPORTANT SAFEGUARDS / PRECAUTIONS
15. POWER LINES - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light of power circuits, or
where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension cords as
this can result in a risk of fire or electric shock.
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall outlet and
refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference unless the modifications are expressly approved in the
owner’s manual. The user could lose the authority to operate this equipment if an unauthorized change or
modification is made.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground should be
connected to the grounding system of the building as close to the point of cable entry as practical.
The serial number of this product may be found on the back of the TV. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Model No.
Serial No.
Dealer Purchase from
Date of Purchase
Dealer Phone No.
Dealer Address
A NOTE ABOUT RECYCLING:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
3
EN
SUPPLIED ACCESSORIES
• Owner’s Manual
(1EMN21883)
• Remote control unit
(NF009UD)
• Batteries
(“AA” x 2)
• If you need to replace these accessories, please refer to the PART NO. with the illustrations and call our
help line mentioned on the front page.
• Depending on your antenna system, you may need different types of Combiners (Mixer) or Separator
(Splitter). Contact your local electronics store for these items.
FEATURES
• DTV/TV/CATV
This TV lets you easily switch TV(NTSC) and DTV(ATSC) with the remote control. This feature enables you to simply
view from conventional analog TV to Standard Definition TV, High Definition TV. You can also connect this TV to CATV
if you have a CATV box.
• Program Information Display (DTV)
You can display the title, contents and other information of the current DTV program on the screen.
• Autoscan
This TV can automatically scan and memorize the channels receivable in your residential area. This feature eliminates the need of a difficult setting procedure.
• V-CHIP
This feature lets you set the viewing limitations to prevent your children from watching inappropriate programs.
• Closed Caption Decoder
This TV contains the built-in Closed Caption Decoder that displays text across the screen. It allows you to read
the dialogue of a TV program or other information in the Closed Caption-supported programs.
• MTS/SAP Tuner
This feature allows you to select with the remote control your desired audio language.
• Auto Shut Off Function
If there is no signal input from the antenna terminal and no operation for 15 minutes, the unit will turn itself
off automatically.
• On-Screen Function Display (English / Spanish / French)
This feature lets you select the language displayed in the setup screen from English, Spanish or French.
• Stereo Sound Function
• Full-Function Remote Control
• PLL Frequency Synthesized Tuning
• HDMI Input
This TV accepts 480i / 480p / 720p / 1080i video signals and 32kHz / 44.1kHz / 48kHz audio signals.
• Component VIDEO Input
This TV accepts 480i / 480p / 720p / 1080i video signals.
• S-VIDEO Input
• AV Input
• Analog Audio Output
• Digital Audio Output (Coaxial)
• Resume
This feature will automatically memorize settings if a power failure occurs.
4
EN
IMPORTANT SAFEGUARDS
PRECAUTIONS . . . . . . . . . .
SUPPLIED ACCESSORIES .
FEATURES . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
3
4
4
FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REMOTE CONTROL, TOP AND REAR PANEL FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
BATTERY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ANTENNA CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CONNECTION TO CABLE/SATELLITE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
EXTERNAL CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HDMI CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
COMPONENT CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
S-VIDEO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
ANALOG AUDIO/VIDEO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
AUDIO OUTPUT CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
INITIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
INITIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CHANNEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
AUTOSCAN . . . . . . . . . . . .
CHANNEL LIST . . . . . . . . .
MANUAL REGISTER . . . . .
ANTENNA CONFIRMATION
LANGUAGE SELECTION . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
13
14
15
16
17
WATCHING TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CHANNEL SELECTION . . . . . . . . . . . . . . .
VOLUME ADJUSTMENT . . . . . . . . . . . . . .
STILL MODE . . . . . . . . . . . . . . . . . . . . . . .
SWITCHING AUDIO . . . . . . . . . . . . . . . . . .
SWITCHING EXTERNAL INPUT . . . . . . . . .
CHANGING THE SCREEN DISPLAY MODE
SCREEN INFORMATION . . . . . . . . . . . . . .
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
18
18
19
19
20
21
22
23
SUPPLIED ACCESSORIES / FEATURES / CONTENTS
CONTENTS
OPTIONAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SETUP SCREEN . . . . . . .
PICTURE ADJUSTMENT .
CLOSED CAPTION . . . . . .
DTV CLOSED CAPTION . .
CLOSED CAPTION STYLE
V-CHIP . . . . . . . . . . . . . . .
HDMI AUDIO . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
24
25
26
26
28
31
MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
SYMBOLS USED IN THIS MANUAL
The following is the description for the symbols used in this manual.
TV
: Settings only for the analog mode
DTV
: Settings only for the digital mode
• If there is no symbol under the function heading, those are common settings for the analog
mode and digital mode.
5
EN
FUNCTIONS
REMOTE CONTROL, TOP AND REAR PANEL FUNCTION
SLEEP button (p23)
To turn the power off automatically at
preset time
INPUT
SLEEP SELECT
POWER
POWER button (p12)
INPUT SELECT button (p20)
To select TV or external input mode (to
access DVD, VCR, etc.)
AUDIO button (p19)
To turn TV on/off
1
2
3
4
5
6
To display on-screen menu
7
8
9
s / B / K / L buttons (p12)
To move left / right / up / down through
the items
-
0
Channel number buttons (p18)
To select channels
SETUP button (p23)
AUDIO
STILL
SCREEN
MODE
SETUP
• Analog mode (TV)
To select audio mode
• Digital mode (DTV)
To select audio language
STILL button (p19)
Pauses the image shown on the screen
SCREEN MODE button (p21)
To Select aspect ratios available for the
screen
ENTER button (p12)
To decide the command of setting when
the menu is displayed
INFO button
ENTER
INFO
BACK
BACK button (p22)
To go back to the previous operation in menu
CH RETURN
VOL. X/ Y buttons (p18)
VOL.
To adjust volume
MUTE button (p18)
To mute sound
MUTE
CH
• Analog mode (TV) (p22)
To display channel No., signal type
and TV setting
• Digital mode (DTV) (p22)
To display channel information, signal
type and TV setting
• External mode (p20)
To display external mode, signal type
and TV setting
CH K/ L buttons (p18/p20)
CH RETURN button (p18)
To select channels and external input
mode
To return to previously viewed channel
SETUP button (p23)
To display on-screen menu
VOLUME X/ Y buttons (p18)
To adjust volume and move right(X)/left(Y) through the
menu items
CHANNEL K/ L buttons (p18)
TV CONTROL
SETUP
VOLUME
CHANNEL
INPUT SELECT/
ENTER
POWER
To select channels and move up/down through the menu
items
POWER button (p12)
To turn TV on/off
INPUT SELECT/ENTER button (p20/p12)
• To select TV or external input mode (to access DVD,
VCR, etc.)
• To decide the command of setting when the menu is
displayed
Infrared Sensor Window
STANDBY
POWER ON
To receive the infrared rays transmitted from the remote
control
NOTE:
6
• With buttons [VOL. X/ Y] or [MUTE], you can only adjust the volume of the main unit. You cannot adjust the volume of the
external devices with these buttons.
EN
AUDIO OUT jacks
Connect audio cable here through
the audio in jacks of audio equipment.
DIGITAL AUDIO OUT
(COAXIAL) jack
Connect an optional coaxial digital audio cable here through the
coaxial digital audio in jack of a
decoder or audio receiver.
ANT. IN
HDMI IN jacks
Connect HDMI cable and audio
cable coming from the HDMI and
audio out jacks of external devices.
L
L
AUDIO
AUDIO OUT
DIGITAL
AUDIO OUT
(COAXIAL)
HDMI IN
R
R
HDMI
from underneath
Rear of this TV
Y
ANT. IN
Y
VIDEO
FUNCTIONS
ANT. IN jack
Connect your antenna or cable
box here.
VIDEO
DIGITAL
AUDIO OUT
(COAXIAL)
L
AUDIO OUT
L
L
Pb
R
Pr
AUDIO
AUDIO
R
R
HDMI IN
HDMI
L
Pb
R
Pr
AUDIO
COMPONENT2
L
AUDIO
COMPONENT1
L
S-VIDEO1
AUDIO
R
VIDEO2
R
VIDEO1
S-VIDEO2
from underneath
Y
Y
Pb
L
Pr
R
AUDIO
Pr
R
COMPONENT2
COMPONENT jacks
Connect component cable
and audio cable coming
from the component and
audio out jacks of external
devices.
VIDEO
Pb
L
AUDIO
VIDEO
COMPONENT1
L
L
AUDIO
AUDIO
R
R
VIDEO2
VIDEO1
S-VIDEO1
S-VIDEO2
S-VIDEO jacks
Connect S-Video cable with
audio cable coming from the
S-Video and audio out jacks
of external devices.
VIDEO jacks
Connect video cable and
audio cable coming from
the video and audio out
jacks of external devices.
INSTALLING THE BATTERIES
Install two AA batteries (supplied) matching the polarity indicated inside battery compartment of the remote
control.
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh
ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
7
EN
PREPARATION FOR USE
CONNECTION
This section describes how to connect this TV to reception and other sources.
MAKE SURE YOU HAVE AN ANTENNA.
As DTV is only available over the air, you need an antenna to receive a digital signal.
NOTE:
• Be sure that antenna or cable is connected properly before plugging the power cord.
[ANTENNA CABLE CONNECTION]
1) When connecting TV to antenna
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.
2) When connecting TV to cable TV company (without box)
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.
VHF / UHF
antenna
Rear of this TV
Coaxial cable
(commercially available)
or
ANT. IN
Y
ANT. IN
Y
VIDEO
VIDEO
DIGITAL
AUDIO OUT
(COAXIAL)
L
AUDIO OUT
R
L
L
Pb
R
Pr
AUDIO
AUDIO
R
HDMI IN
HDMI
L
Pb
R
Pr
L
AUDIO
COMPONENT2
AUDIO
L
S-VIDEO1
AUDIO
R
COMPONENT1
VIDEO2
R
VIDEO1
S-VIDEO2
Coaxial cable
Cable TV
company
(commercially available)
*Once connections are completed, turn on the TV and begin initial setup.
Channel scanning is necessary for the TV to memorize all available channels in your area.
(Refer to “INITIAL SETTINGS” on page 12.)
NOTES:
• For your safety and to avoid damages to the unit, unplug the coaxial cable from the ANT. IN jack before moving the unit.
• If you use an antenna in order to receive analog TV, the same antenna generally will work for DTV reception.
Outdoor or attic antennas will be more effective than set-top versions.
• To easily switch between antenna and cable wires, you can purchase an “Antenna Selector” commercially available.
• If you connect a cable system directly, contact the CATV installer.
[CONNECTION TO CABLE/SATELLITE BOX]
1) Connect the coaxial cable on your home outlet to the input jack of the CABLE/SATELLITE box.
2) Use the coaxial cable to connect the ANT. IN jack of this TV and the output jack of the CABLE/SATELLITE
box.
*Required cables in 2) and connecting methods differ depending on the CABLE/SATELLITE box. For more information, please contact the cable/satellite provider.
Rear of this TV
Satellite
dish
Cable box or
Satellite box
or
Y
ANT. IN
L
R
L
8
EN
Coaxial cable
(commercially available)
(commercially available)
ANT. IN
L
Pb
R
Pr
AUDIO
AUDIO
R
HDMI IN
HDMI
Coaxial cable
Y
VIDEO
VIDEO
DIGITAL
AUDIO OUT
(COAXIAL)
AUDIO OUT
Cable TV
company
L
Pb
R
Pr
L
AUDIO
AUDIO
COMPONENT2
COMPONENT1
L
S-VIDEO1
AUDIO
R
VIDEO2
R
VIDEO1
S-VIDEO2
EXTERNAL CONNECTION
PREPARATION FOR USE
[HDMI CONNECTION]
1) This is the best method to connect this TV to a video device with the HDMI output jack, such as a DVD
player with HDMI output jack, etc. It can minimize the deterioration of image quality.
Use the HDMI cable for connection.
HDMI cable
(commercially available)
To HDMI IN jack
HDMI OUT
ANT. IN
L
L
AUDIO
AUDIO OUT
To HDMI output jack
DIGITAL
AUDIO OUT
(COAXIAL)
DVD Player with the HDMI output jack
HDMI IN
R
R
HDMI
Rear of this TV
NOTES:
• This TV accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.
• This TV accepts only 2 channel audio signal (LPCM).
• You need to select “PCM” for the digital audio output of the device you connect or the HDMI audio setting. Audio sometimes makes
no sound if you select “Bitstream”, etc.
• This TV only accepts signals corresponding EIA861.
2) When your video device has the DVI output jack, use the HDMI conversion cable from DVI output jack for
connection as illustrated below.
HDMI-DVI conversion cable
(commercially available)
To HDMI IN jack
To DVI output jack
DVI OUT
ANT. IN
L
L
AUDIO
AUDIO OUT
Cable Box or Satellite Box
with the DVI output jack
AUDIO OUT
R
L
DIGITAL
AUDIO OUT
(COAXIAL)
R
HDMI IN
R
HDMI
To AUDIO Rear of this TV
input jacks
To audio
output jacks
Audio cable
(commercially available)
NOTES:
• This TV accepts 480i / 480p / 720p / 1080i video signals.
• Audio signals are converted to an analog signal from the digital if you make a connection above.
• DVI does not show image if the 480i does not accept EIA/CEA-861/861B.
“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.”
9
EN
[COMPONENT CONNECTION]
1) This is a better method to connect this TV to video devices with the Component output jack, such as a
DVD player, etc.
Use the Component video cable for connection.
If you connect component output jacks to COMPONENT1 input jack, connect an audio cable to AUDIO L/R
jacks of COMPONENT1.
If you connect component output jacks to COMPONENT2 input jack, connect an audio cable to AUDIO L/R
jacks of COMPONENT2.
Component video cable
(commercially available)
To COMPONENT1
input jacks
To component video
output jacks
Y
Y
Pb
AUDIO
AUDIO
Pr
Pr
R
R
COMPONENT2
To audio
output jacks
VIDEO
Pb
L
L
DVD Player with the component
video output jacks
VIDEO
L
L
AUDIO
AUDIO
R
R
COMPONENT1
VIDEO2
VIDEO1
S-VIDEO2
Rear of this TV
To AUDIO
input jacks
Audio cable
S-VIDEO1
(commercially available)
NOTE:
• This TV accepts 480i / 480p / 720p / 1080i video signals.
[S-VIDEO CONNECTION]
1) This is a good method to connect this TV to the video devices with the S-Video output jack. You can
expect better picture quality than the normal video cable connection.
Use the S-Video cable for connection.
If you connect S-Video output jack to S-VIDEO1 input jack, connect an audio cable to AUDIO L/R jacks of
VIDEO1.
If you connect S-Video output jack to S-VIDEO2 input jack, connect an audio cable to AUDIO L/R jacks of
VIDEO2.
To S-VIDEO1
input jack
S-Video cable
(commercially available)
To S-Video
output jack
AUDIO
OUT
Y
VIDEO S-VIDEO
OUT
OUT
Pb
L
To audio
output jacks
Audio cable
(commercially available)
Pr
R
AUDIO
Pr
R
COMPONENT2
VIDEO
COMPONENT1
L
L
AUDIO
AUDIO
R
R
VIDEO2
NOTE:
EN
VIDEO1
S-VIDEO1
S-VIDEO2
To AUDIO Rear of this TV
input jacks
• If you connect to the S-VIDEO jack and the VIDEO jack at the same time, S-Video connection will have priority.
10
VIDEO
Pb
L
AUDIO
DVD/VCR with
the S-Video output jack
Y
[ANALOG AUDIO/VIDEO CONNECTION]
1) This is the general method to connect this TV to video devices with the video and audio output jacks, such
as VCR, Camcorder, Video Game, etc.
When the audio jack of video devices is monaural, connect this TV to the AUDIO L jack.
Video cable
To video
output jack
AUDIO
OUT
Y
VIDEO
OUT
Pb
Video Game
AUDIO
To audio
output jacks
Pr
VIDEO
Pb
AUDIO
Pr
R
R
COMPONENT2
VCR
VIDEO
L
L
Camcorder
Y
PREPARATION FOR USE
To VIDEO1
input jack
(commercially available)
COMPONENT1
L
L
AUDIO
AUDIO
R
R
VIDEO2
VIDEO1
S-VIDEO1
S-VIDEO2
To AUDIO Rear of this TV
input jacks
Audio cable
(commercially available)
[AUDIO OUTPUT CONNECTION]
1) If you connect this TV to an external audio device, you can enjoy multi-channel audio like 5.1ch digital
broadcasting sound.
Use the Digital Audio Coaxial cable or Audio cable for connection.
Digital audio coaxial cable
(commercially available)
To DIGITAL AUDIO OUT jack
MD deck, DAT deck, etc.
COAXIAL
ANT. IN
L
L
AUDIO OUT
To coaxial digital
audio input jack
DIGITAL
AUDIO OUT
(COAXIAL)
R
AUDIO
HDMI IN
R
HDMI
Rear of this TV
To AUDIO
OUT jacks
Dolby Digital decoder
or
AUDIO
IN
To audio input jacks
Stereo system
Audio cable
(commercially available)
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
11
EN
INITIAL SETTINGS
Hint: Before starting initial setup you must connect antenna.
INITIAL SETTINGS
3
This section describes the initial settings when you
first turn on the power after purchase. The initial
setting items are shown below.
Select your language using [K /L], press
[ENTER].
When you first turn on the power, the following
screen is displayed.
Initial Setup
• LANGUAGE SELECTION
You can select the menu language displayed on
the screen among English, Spanish and French.
• AUTOSCAN (TV/DTV)
(Select “Air” when using antenna)
The channels broadcasted in TV and DTV are
automatically scanned and memorized. Only the
receivable channels in the area where this TV is
used will be memorized.
• AUTOSCAN (CATV)
(Select “Cable” when using RF/Incoming cable)
The channels broadcasted in CATV are automatically scanned and memorized.
Select the language for setup display.
English
Elija idioma de preparación.
Español
Sélectionner langue écran config.
Français
Select
ENTER
Enter
SETUP
Exit
The Antenna Confirmation will be displayed in
the selected language after you press [ENTER].
4
Select source of ANT. IN jack using [K /L], press
[ENTER].
Initial Setup
Air
Make sure the antenna is connected to "ANT IN" jack.
Select the destination of "ANT IN" jack.
Cable
Air
INPUT
SLEEP SELECT
POWER
Or
Cable
ANT IN
1
2
3
4
5
6
7
8
9
-
0
Select
ENTER
Enter
BACK
SETUP
Back
Exit
AUDIO
STILL
5
Autoscan will start automatically.
Initial Setup
SCREEN
MODE
SETUP
Now the system is scanning for channels,please wait.
5%
ENTER
BACK
INFO
Analog channels
1ch
Digital channels
0ch
SETUP
1
2
After making all the necessary connections, turn
on this TV.
Press [POWER]. Initial Setup menu will appear.
• This operation may take a few moments.
• If Initial Setup menu does not appear, press
and hold [ENTER] for 3 seconds, initial setup
will appear then proceed to step 3. If you have
already turned on this TV before, refer to “LANGUAGE SELECTION” on page 17 to select a
language for the on-screen displays.
Exit
• When scanning has completed, the lowest
memorized channel will be displayed.
NOTES:
• The initial Autoscan function can be executed for either “Air”
or “Cable” only once. When you change the connection
(Air/Cable), set the “Autoscan” again. (Refer to page 13.)
• If you connect cable system directly, contact the
CATV installer.
• When the scanning is not completed, Helpful Hint will be
displayed every time you turn on the power. If you have
previously registered channels when this screen appears
you can select a channel with number buttons.
2-0
No channel is registered.
Press and hold "ENTER" key for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Mantenga oprimida la tecla "ENTER" durante 3 segundos.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Maintenir la touche "ENTER" pressée 3 secondes.
Contacter numero d'urgence dans manuel ou arrière appareil.
12
EN
• Support hotline is provided on the front page of this
manual.
CHANNEL SETTINGS
AUTOSCAN
If you switch wires (e.g. between antenna and
CATV) or if you move the TV to a different area
after the initial setting, you need to perform
Autoscan again. This function lets you easily select
the receivable channels with [CH K/L] and the TV
memorizes them even if you switch wires.
3
For TV channels, using [K /L], select “Air”.
For CATV channels, select “Cable”.
Autoscan
Cable
Air
Cable
1hour
Cable
Or
ANT IN
SCREEN
MODE
ENTER
INFO
BACK
• Press [ENTER].
Scanning and memorizing the channels automatically starts.
CH RETURN
MUTE
Now the system is scanning for channels, please wait.
CH
72%
Analog channels
10ch
Digital channels
SETUP
NOTE:
• Make sure the TV is connected to antenna or cable.
1
INITIAL SETTINGS / CHANNEL SETTINGS
0
SETUP
VOL.
Air
Select the destination of "ANT IN" jack.
STILL
-
Back
Autoscan will rescan all channels.
This may take a while to complete.
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
6ch
Exit
• When the scanning and memorizing are completed, the lowest memorized channel in the
broadcasting will be displayed.
NOTES:
• If you connect a cable system directly, contact the
CATV installer.
• If you press [POWER] or [SETUP] during Autoscan, this
setting will be canceled.
• If there is no reception connected or poor signal is detected,
a Hint will appear on screen once scanning stops.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Autoscan”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
13
EN
CHANNEL LIST
3
The Channel List function lets you skip the unnecessary channels from the Channel registration list.
Select the channel you want to skip.
• Using [K/L], select the channel.
Channel List
STILL
-
Highlight channels for
Ch Up/Down key selection.
0
SCREEN
MODE
SETUP
DTV
6
DTV
8
DTV
48
DTV
67
9
27
58
ENTER
Ch Select
INFO
BACK
1
MUTE
Watch/Skip
Back
• Press [ENTER], and the highlight on the
selected channel disappears, then the channel
is set as skip. With [CH K /L], you cannot
select the channel set as skip.
• If you want to receive the skipped channel,
select your desired channel and press
[ENTER].
• If you skip a major channel, you skip the minor
channels too.
CH RETURN
VOL.
ENTER
BACK
CH
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
NOTE:
• The channel with “DTV” indicated on the display is ATSC,
otherwise the channel is NTSC.
4
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Channel List”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
14
EN
To exit the setup, press [SETUP].
MANUAL REGISTER
3
Select the channel you want to add.
• Using Channel number buttons, select your
desired channel.
You can register the remainder of channels that
were not scanned by the Autoscan function due to
the bad reception status at the initial setting.
11
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
7
8
9
Manual Register
For Analog channels,
select a channel to register
using number keys.
For Digital channels,
you must perform Autoscan function.
Register
AUDIO
Back
CHANNEL SETTINGS
BACK
Ch Change
STILL
-
0
• Select “Register” with [ENTER].
SCREEN
MODE
SETUP
4
To exit the setup, press [SETUP].
ENTER
BACK
1
INFO
Display the setup screen.
NOTES:
• If the setup is completed successfully, “Registered to the
channel list.” is shown on the screen.
• If “Video1” is being used, set up will not be completed successfully. “Unavailable” will be shown on screen.
• Press [SETUP].
The following setup screen is displayed.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Manual Register”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
15
EN
• If the channel is set to external input, you cannot confirm the antenna situation.
ANTENNA CONFIRMATION
You can verify the signal strength of each channel
to get a clearer picture.
Video1
Antenna
Back
INPUT
SLEEP SELECT
POWER
Indicator is available
for antenna signal only.
1
2
3
4
5
6
CH
Ch Change
AUDIO
7
8
-
0
9
3
STILL
SCREEN
MODE
SETUP
ENTER
INFO
BACK
CH RETURN
VOL.
1
CH
MUTE
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
2
Select “CHANNEL” and press [ENTER] to confirm.
• Using [K /L], select “Antenna”.
Channel
Autoscan
Channel List
Manual Register
Antenna
• Press [ENTER].
• Using Channel number buttons or [CH K /L],
select the channel you want to confirm the
antenna situation.
11
Antenna
Back
Now
70 Peak
CH
16
EN
80
Ch Change
To exit the setup, press [SETUP].
LANGUAGE SELECTION
You can choose your on screen language from one
of the following English, Spanish or French.
STILL
-
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
1
MUTE
CHANNEL SETTINGS
CH RETURN
VOL.
CH
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
2
Select “LANGUAGE” and press [ENTER] to confirm.
• Using [K /L], select “English”, “Español” or
“Français”.
Language
Select the language for setup display.
English
Elija idioma de preparación.
Español
Sélectionner langue écran config.
Français
• Press [ENTER].
3
To exit the setup, press [SETUP].
17
EN
WATCHING TV
NTSC
CHANNEL SELECTION
CH4-1 No signal No signal
You can select the channel by using either [CH K/L]
or Channel number buttons. How to select the
channel in each way is shown below.
18:30
CH4-1
CH4-2
CH4-3
19:00
CH4
INPUT
SLEEP SELECT
POWER
ATSC
18:00
CH4-1 No signal CH4-3
19:30
1
2
3
4
5
6
7
8
9
CH4-1
AUDIO
: change automatically
: change manually by pressing [CH
on your remote control
STILL
-
0
SCREEN
MODE
SETUP
CH4-2 No signal
20:00
/ ]
NOTE:
• “No Signal” will appear on the screen after the minor-
ENTER
channel broadcast is over.
You will need to change the channel to continue
watching another TV program.
INFO
BACK
CH RETURN
VOL.
1
MUTE
CH
Using [CH K/L], or Channel number buttons
and pressing [ENTER].
• Using [CH K/L], change the channel.
• Same operation is available with [CHANNEL
K/L] on the top panel of the main unit.
• When you select a channel, press the channel
number you want to view with Channel number
buttons. The selected channel will be displayed.
- When selecting analog channel 12
1
2
2
-
1
ENTER
• If the channel broadcasts NTSC and ATSC both
and you don't press [–], then you will receive the
NTSC channel only. The moment you press [–],
the lowest memorized digital channel will be displayed.
• When you press [CH RETURN], the previously
selected channel will be selected.
NOTE:
• In the DTV broadcasting, one channel sometimes broadcasts multiple programs depending on the air time. In this
case, the main channel is called major channel and the
minor-channel is called minor channel.
About minor-channel broadcasting:
There may be different programs being broadcast on minor-channels through a single channel from ATSC. You can watch each minorchannel program being broadcast by selecting
one of the minor-channels.
18
EN
This section describes how to adjust the volume
when viewing TV. The Mute function, which is useful when you have a visitor or a phone call, will be
also described.
INFO
BACK
CH RETURN
VOL.
1
ENTER
- When selecting digital channel 12-1
Be sure to press [–] before entering the
minor-channel number.
1
VOLUME ADJUSTMENT
MUTE
CH
Using [VOL. X/Y] or [MUTE].
[VOL. X/Y]
• You can adjust the audio volume with [VOL. X/Y].
• The volume bar is displayed at the bottom of
the screen when adjusting the volume.
• Same operation is available with [VOLUME
X/Y] on the top panel of the main unit.
Volume
20
• The volume bar display will automatically disappear in a few seconds.
[MUTE]
• Press [MUTE] on the remote control to mute
the sound.
• To release the Mute status, press [MUTE]
again or press [VOL. X/Y].
Mute
• “Mute” is displayed on the screen for a few seconds.
STILL MODE
When the broadcasting has stereo audio and
monaural audio...
You can freeze the image shown on the screen.
1
2
MONO / STEREO
3
4
5
6
7
8
9
-
0
AUDIO
SAP / MONO
STILL
SAP / MONO
When the broadcasting is having only monaural
audio...
SCREEN
MODE
SETUP
MONO / STEREO
When the broadcasting has SAP and monaural
audio...
MONO
(cannot be switched.)
Pause the image.
• When you press [STILL], the image shown on
the screen is paused.
STEREO : Outputs stereo-audio
SAP
: Outputs second audio program
MONO : Outputs mono-audio
Still
WATCHING TV
1
DTV
• The audio is not paused and keeps on reading
out.
• If the digital signal is gone or protected, the
image will remain paused and the audio will be
muted.
• The Still function will be released after 5
minutes.
2
Canceling Still function.
• The Still function will be canceled by pressing
any button while Still function is working.
1
Switch the audio language.
• When you press [AUDIO], the currently selected
language and the number of received languages
will be displayed on the screen.
• Every time you press [AUDIO], the language
will be switched.
6-1
English 1/3
English 1/3
Spanish 2/3
NOTE:
• Press any key except [POWER] to cancel still mode.
Other 3/3
"Other" is indicated
when the language is not English,
Spanish or French.
* For international stations audio
language will still be displayed as
English.
SWITCHING AUDIO
This section describes how to switch the audio in
the analog mode and how to switch the audio language in the digital mode.
AUDIO
7
8
-
0
9
STILL
SETUP
SCREEN
MODE
NOTE:
TV
1
• Languages you can switch differ depending on
the receiving broadcast.
• The information display will automatically disappear in one minute.
• The [AUDIO] feature does not affect external source sound.
Switch the audio.
• Every time you press [AUDIO], the audio will
be switched as below.
6
SAP / STEREO
When the broadcasting has all audio...
SAP / STEREO
SAP / MONO
SAP / STEREO
19
EN
SWITCHING EXTERNAL INPUT
When you connect external devices including a
DVD player and home audio system, you can easily
switch the input mode with the remote control.
INPUT
SLEEP SELECT
POWER
1
2
3
4
5
6
• When you press [INFO], the current external
input mode, the type of resolutions for video
signal, TV aspect ratio, CC and TV rating will
be displayed at the top-right of the screen.
1) When using VIDEO1 or S-VIDEO1 input jack
Video1
480i
SD
TV-PG DLSV CC
AUDIO
7
8
-
0
9
STILL
SCREEN
MODE
SETUP
2) When using VIDEO2 or S-VIDEO2 input jack
Video2
ENTER
480i
INFO
BACK
SD
TV-PG DLSV CC
CH RETURN
VOL.
MUTE
CH
3) When using COMPONENT1 input jacks
1
Switch the input mode.
Component1
1080i
• When you press [INPUT SELECT] or [CH
K/L] on the remote control, the input mode will
be switched as below.
HD
NONE
4) When using COMPONENT2 input jacks
TV/DTV channel
Component2
Video1
1080i
HD
NONE
Video2
Component1
5) When using HDMI IN jack
Component2
HDMI
1080i
HDMI
HD
16:9
NONE
: press [CH K]
• To use the VIDEO1 or S-VIDEO1 input jack on
the TV, select “Video1”.
• To use the VIDEO2 or S-VIDEO2 input jack on
the TV, select “Video2”.
• To use the COMPONENT1 input jacks on the
TV, select “Component1”.
• To use the COMPONENT2 input jacks on the
TV, select “Component2”.
• To use the HDMI IN jack on the TV,
select “HDMI”.
20
EN
• The information display will automatically disappear in one minute.
CHANGING THE SCREEN DISPLAY MODE
Each 4 types of display mode can be selected in the
screen mode in both 4:3 and 16:9 TV aspect ratio.
You can select your favorite screen mode and enjoy
the program.
AUDIO
7
8
-
0
9
Switch the Screen mode.
• Every time you press [SCREEN MODE], the TV
aspect ratio will be switched alternately.
2
Press [SCREEN MODE] repeatedly until the normal screen displays.
NOTE:
STILL
• You may not switch the display mode depending on the program.
SCREEN
MODE
SETUP
1
ENTER
INFO
When the broadcast is sending 4:3 video
signal...
When the broadcast is sending 16:9 video
signal...
Sidebar
(normal)
Full
Full
(normal)
Zoom
Wide
Cinema
Expand
Cinema
[Sidebar]
Sidebar will display a 4:3 picture at its standard
4:3 size. Sidebars will be displayed on the right
and left edges of the screen.
[Full]
Full will display a 4:3 picture at a 16:9 size,
with horizontal elongation necessary to fill the
screen.
[Cinema]
Cinema will display a 4:3 picture at a 16:9 size,
with less horizontal elongation necessary to fill
the screen because a little bit of the top and
bottom edge of the screen will be cut off.
[Wide]
Wide will display the center of the picture as original size and the outer sides of the picture will be
elongated. The size of the picture will depend on
the original signal.
WATCHING TV
BACK
[Full]
A picture will be displayed at 16:9 size as it is.
[Zoom]
Zoom will display a 16:9 picture without changing its horizontal to vertical ratio, at its maximum size.
[Cinema]
Cinema will display a 16:9 picture with vertical
elongation.
[Expand]
Expand will display a 16:9 picture with horizontal elongation.
21
EN
DTV
SCREEN INFORMATION
You can display the currently selected channel
number or other information such as the audio
mode on the screen for checking.
1
AUDIO
7
8
9
-
0
SCREEN
MODE
• The following information is displayed.
ENTER
(1) Program title
INFO
BACK
(2) Broadcast station
CH RETURN
VOL.
MUTE
Display the detailed information for the channel.
• Press [INFO] on the remote control.
The currently selected program details are displayed on the screen.
STILL
SETUP
In the digital mode, the detailed information for the
currently selected channel such as the Program
guide is displayed.
(3) Program guide (max. 4 lines displayed)
CH
(4) Channel number
TV
In the analog mode, the currently selected channel
number and the audio mode are displayed.
1
(5) Audio language (“Other” is displayed when
the audio language cannot be acquired, or
the acquired languages are other than
English, Spanish or French.)
Display the channel number and the audio
mode.
(6) Effective scanning lines and scan mode
• Press [INFO] on the remote control.
The currently selected channel number, the
audio mode, the type of resolutions for video
signal, TV aspect ratio, CC and TV rating are
displayed at the top-right of the screen.
(8) Program aspect ratio
(7) Program definition
(9) Program rating
(10) CC (Not available if the CC set to “Off”)
(1)
Buffy Vampire Slayer
6
SAP / STEREO
480i
480i
SD
SD
4:3
4:3
(2)
(4)
HDTV
A quarter-century ago,which may now qualify as the
good old days of newspapering,run-of-paper sales
accounted for 80 percent of the industry's advertising
revenues.Department stores and supermarket were
6-1
(5)
English 1/2
1080i
1080i
HD
HD
16:9
16:9
TV-PG DLSV CC
CC
(6), (7), (8)
TV-PG DLSV CC
CC
(3)
• To clear the display, press [BACK] or [INFO]
again.
(9) (10)
NOTES:
• When the program guide is displayed in more than 5 lines,
use [ K/ L] and scroll for reading.
• “No description provided” is displayed when the program
guide is not provided.
• The following screen is displayed when connecting to external devices:
e.g.) When using VIDEO1 input jack for connection
Video1
480i
480i
SD
SD
TV-PG DLSV CC
CC
22
EN
OPTIONAL SETTINGS
SLEEP TIMER
SETUP SCREEN
The Sleep Timer function will automatically turn off
the power of the unit at a preset time.
This section describes the overview of the setup
screen displayed when you press [SETUP].
For more details, see the reference page for each
item.
INPUT
SLEEP SELECT
1
2
3
4
5
6
7
8
9
The setup screen consists of the function setting
items below.
AUDIO
•
To exit settings.
STILL
-
0
SCREEN
MODE
SETUP
•
You can adjust the picture quality (Picture Mode,
Brightness, Contrast, Color, Tint, Sharpness,
Color Temp., and Energy Saving).
(Refer to “PICTURE ADJUSTMENT” on page 24.)
ENTER
1
Use Sleep Timer.
• Press [SLEEP] on the remote control.
• The setting display for Sleep Timer is shown on
the screen.
Sleep
2
•
You can automatically scan the receivable channels and watch or skip the channel as necessary.
(Refer to “AUTOSCAN” on page 13.)
Off
•
Set the timer.
You can change the display format for Closed
Caption as well as varied font styles, which displays the dialogue of a TV program or other information across the screen. (Refer to “CLOSED
CAPTION” on page 25.)
Also, can set the viewing limitations such as
V-Chip of the MPAA rating and the TV rating.
(Refer to “V-CHIP” on page 28.)
HDMI Audio if the TV is connected to a digital
external device such as a DVD player. (Refer to
“HDMI AUDIO” on page 31.)
• You can select 10, 20, 30, 40, 50, 60, 70, 80
and 90 minutes by pressing [SLEEP].
(You cannot set the timer per 1 minute. )
• You can set the timer up to 90 minutes.
• After setting, you can check the remained time
per 1 minute by pressing [SLEEP].
• To cancel the sleep timer, press [SLEEP]
repeatedly until “Sleep Off” is displayed.
• The Sleep Timer setting display will automatically disappear in a few seconds.
Sleep
WATCHING TV / OPTIONAL SETTINGS
POWER
•
Off
NOTE:
• When you disconnect the unit from the AC outlet or when a
power failure occurs, the sleep timer setting will be cancelled.
You can change the language (English, Spanish,
French) displayed in the setup screen.
(Refer to “LANGUAGE SELECTION” on page 17.)
NOTE:
• To move to the normal screen, press [SETUP].
23
EN
Contrast
Using [s / B], adjust to increase or decrease
contrast.
s: To decrease contrast
B: To increase contrast
PICTURE ADJUSTMENT
You can enjoy your favorite picture mode selecting
from four picture default settings that will adjust colors to enhance your viewing experience. Also, the
brightness, contrast, color, tint, sharpness color
temperature, and energy saving settings can be
changed.
Contrast
ENTER
ENTER
Enter
Color
36
INFO
BACK
Adjust
1
Move
Color
Using [s / B], adjust to be brilliant or pale color.
s: To pale
B: To brilliant
SCREEN
MODE
SETUP
60
Adjust
Move
ENTER
Enter
Tint
Using [s / B], adjust to obtain natural skin tones.
s: To red
B: To green
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
Tint
R2
Adjust
Move
ENTER
Enter
Sharpness
Using [s / B], adjust the detail of the picture.
s: To soft
B: To clear
Sharpness 0
2
Select “PICTURE”, and press [ENTER] to confirm.
• Using [K /L], select your desired item and
press [ENTER] to confirm.
Adjust
Move
ENTER
Enter
Reset Settings
Using [K /L], select “Reset”.
You can reset setting of the Picture Mode you select.
Reset Settings
Picture
This function resets the
Cancel
Brightness
30
"Dynamic" setting for Picture Mode
Reset
Contrast
60
to factory default.
Color
36
Dynamic
Picture Mode
Tint
0
Sharpness
0
Reset Settings
Neutral
Color Temp.
Off
Energy Saving
3
Color Temp.
Using [K/L], adjust Color Temperature from the selection, then press [ENTER]. (Cool, Neutral and Warm)
Adjust the picture quality.
• Using [K/L], select the picture quality item you
want to adjust.
Picture
Picture Mode
Picture Mode
Using [K /L], adjust Picture Mode from the
selection, then press [ENTER]. (Standard,
Dynamic, Movie and News)
Brightness
Contrast
Color
Tint
Sharpness
Reset Settings
Cool
Color Temp.
Neutral
Energy Saving
Warm
Picture
Picture Mode
Standard
Brightness
Dynamic
Contrast
Movie
Color
News
Energy Saving
Using [s / B], adjust brightness of backlight.
s: To bright
B: To dark
Tint
Sharpness
Reset Settings
Color Temp.
Energy Saving Off
Energy Saving
Adjust
Brightness
Using [s / B], adjust until the darkest parts of
the picture are as bright as you prefer.
s: To decrease brightness
B: To increase brightness
Brightness
24
EN
ENTER
Enter
• The adjustment bar for picture quality item is
displayed on the screen.
NOTE:
• To move to the normal screen, press [SETUP].
30
Adjust
Move
ENTER
Enter
4
To exit the setup, press [SETUP].
CLOSED CAPTION
You can view specially labeled (cc) TV programs,
movies, news and prerecorded tapes, etc. with
either a dialogue caption or text display added to
the program.
4
Switch the Closed Caption mode.
Closed Caption
Conventional CC
Off
DTV CC
CC1
CC Style
CC2
CC3
CC4
Text1
You can also change the font size and the font style
by selecting options in the “Conventional CC”.
Text2
Text3
Text4
STILL
-
• Using [K /L], select the desired closed caption,
then press [ENTER].
0
SCREEN
MODE
SETUP
[Caption Mode]
ENTER
CH RETURN
VOL.
CH
MUTE
OPTIONAL SETTINGS
CC1 and Text1:
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
INFO
BACK
(up to 4 lines of script on the screen, where it
does not obstruct relevant parts of the picture).
1
CC3 and Text3:
serve as the preferred data channels.
The captioning or text is often a secondary language translation, simplified English or displayed
at a slower rate.
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
CC2, CC4, Text2 and Text4:
are rarely available and broadcasters use them
only in special conditions, such as when CC1
and CC3 are not available or Text1 and Text3 are
not available.
2
• There are three display modes according to
programs:
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Paint-on mode: Displays input characters on the
screen immediately.
Pop-on mode : Once characters are stored in
memory, they are displayed all
at once.
Roll-up mode : Displays the characters continuously by scrolling (max. 4 lines).
Detail
Closed Caption
V–chip
HDMI Audio
3
Auto
5
Select “Conventional CC” and press [ENTER] to
confirm.
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
To exit the setup, press [SETUP].
NOTES:
• If the closed caption is not broadcasted, nothing is displayed.
• The closed caption is not displayed when you use HDMI
connection.
• When your TV receives a special effects playback signal
(i.e., Search, Slow and Still) from a VCR’s video output
channel (CH3 or CH4), the TV may not display the correct
caption or text.
• Captions and texts may not match the TV voice exactly.
• Interference may cause the closed caption system not to
function properly.
• The caption or text characters will not be displayed while the
menu display or functions display is shown.
• If a black box appears on the screen, this means that the
TV is set to TEXT mode. To clear screen, select CAPTION
“CC1”, “CC2” , “CC3”, “CC4”or “Off”.
25
EN
DTV CLOSED CAPTION
DTV
Apart from closed captions, DTV has its own closed
captions called DTV CC. Use this menu to change
the settings for DTV CC.
1
CLOSED CAPTION STYLE
1
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Detail
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “Closed Caption” and press
[ENTER] to confirm.
Closed Caption
V–chip
HDMI Audio
Auto
Detail
Closed Caption
V–chip
HDMI Audio
Auto
3
Select “CC Style” and press [ENTER] to confirm.
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
3
Select “DTV CC” and press [ENTER] to confirm.
Closed Caption
Conventional CC
Off
DTV CC
Off
CC Style
4
Switch the Closed Caption Style.
CC Style
User Setting
Font Style
4
Switch the DTV Closed Caption mode.
Closed Caption
Off
Font0
Font Size
Middle
Font Color
White
Font Opacity
Solid
Back Color
Black
Back Opacity
Solid
Edge Color
Black
Edge Type
None
Conventional CC
DTV CC
Off
CC Style
Service1
• Using [K /L], select the desired Closed Caption
Style.
Service2
Service3
Service4
Service5
Service6
• Using [K /L], select the desired DTV Closed
Caption, then press [ENTER].
Off:
Select if you do not want DTV CC. This is the
default.
Service 1 to Service 6:
Select one of these before changing any other
item in the Closed Caption menu. Choose
Service 1 under normal circumstances.
5
Use “User Setting”.
• The “User Setting” function lets you change CC
style.
• Using [K /L], select “User Setting”.
• Press [ENTER] and set “User Setting” to “ON”.
CC Style
User Setting
On
Font Style
Off
Font Size
Font Color
Font Opacity
Back Color
Back Opacity
Edge Color
Edge Type
5
26
EN
To exit the setup, press [SETUP].
[Font Opacity]
Font opacity of the displayed caption can be
switched as below.
Set each item.
• When “User Setting” is set to “On”, you can set
the following items.
• CC style set by “User Setting” will be displayed.
• Using [K /L], select the item you want to set.
• You can switch the setting for each item with
[K /L].
CC Style
Closed Caption
User Setting
Font Style
Font Size
Font Color
Font Opacity
Solid
Back Color
Flash
Back Opacity
Translucent
Edge Color
Transparent
Edge Type
Picture display
[Back Color]
Background color of the displayed caption can
be switched as below.
ABCDEF
GHIJKL
ABCDEFGHIJKL
CC Style
Edge
(Edge Color and Edge Type)
Closed Caption
User Setting
Font
(Font Style, Font Size, Font Color and Font Opacity)
Back
(Back Color and Back Opacity)
• The setting description for each item is shown
below.
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
OPTIONAL SETTINGS
6
[Back Opacity]
Background opacity of the displayed caption can
be switched as below.
[Font Style]
Font style of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
User Setting
Font Size
Font Style
Font Color
Font Opacity
Font Size
Font Color
Back Color
Solid
Font Opacity
Back Opacity
Flash
Back Color
Edge Color
Translucent
Back Opacity
Edge Type
Transparent
Edge Color
Edge Type
[Edge Color]
Edge color of the displayed caption can be
switched as below.
[Font Size]
Font size of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
White
Font Size
Black
Font Color
Red
Font Size
Large
Font Opacity
Green
Font Color
Middle
Back Color
Blue
Small
Back Opacity
Yellow
Back Color
Edge Color
Magenta
Back Opacity
Edge Type
Cyan
User Setting
Font Style
Font Opacity
Edge Color
Edge Type
[Edge Type]
Edge type of the displayed caption can be
switched as below.
[Font Color]
Font color of the displayed caption can be
switched as below.
CC Style
Closed Caption
User Setting
CC Style
Closed Caption
Font Style
Font Size
User Setting
Font Style
White
Font Size
Black
Font Color
Red
Font Opacity
Green
Back Color
Blue
Back Opacity
Yellow
Edge Color
Magenta
Edge Type
Cyan
7
Font Color
None
Font Opacity
Raised
Back Color
Depressed
Back Opacity
Uniform
Edge Color
L.Shadow
Edge Type
R.Shadow
To exit the setup, press [SETUP].
27
EN
V-CHIP
3
You can set the viewing limitations to prevent your
children from watching inappropriate programs
including disagreeable expression and description.
The viewing limitations set for the program can be
released by entering the password.
Enter the password.
• Use Channel number buttons and enter the
4-digit number.
V-Chip
Enter password.
INPUT
SLEEP SELECT
POWER
BACK
PIN Code
1
2
3
4
5
6
7
8
9
-
0
• When you have not set up your password,
enter 0000.
• When the password is correct, the following
“V-Chip” screen is displayed.
AUDIO
STILL
A MPAA Rating
V-Chip
SCREEN
MODE
SETUP
Back
MPAA Rating
B TV Rating
TV Rating
New Password
ENTER
C New Password
INFO
BACK
1
See the following description for setting each
item.
Display the setup screen.
• Press [SETUP].
The following setup screen is displayed.
A MPAA Rating
4
Display the “MPAA Rating” screen.
• Using [K /L], select “MPAA Rating”.
V-Chip
MPAA Rating
TV Rating
New Password
2
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “V-chip”.
Detail
• Press [ENTER].
Closed Caption
V–chip
Auto
HDMI Audio
V-Chip
X
NC-17
R
PG-13
PG
G
NR
• Press [ENTER].
The password entry screen is displayed.
V-Chip
Enter password.
PIN Code
28
EN
BACK
Back
Select
ENTER
View/Block
BACK
Back
Set “MPAA Rating”.
• Using [K /L], select the rating.
• Press [ENTER] and set to “View” or “Block”.
5
• Press [ENTER] and set to “View” or “Block” for
the rating without sub categories.
V-Chip
X
NC-17
R
PG-13
PG
G
NR
Select
6
V-Chip
FV V
ENTER
View/Block
BACK
Back
PG-13 :
PG :
G:
NR :
<Rating Category Explanations>
Mature audience only
No one under 17 admitted
Restricted; under 17 requires
accompanying parent or adult
guardian
Unsuitable for children under 13
Parental Guidance suggested
General Audience
No Rating
NOTES:
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set “X” to “View”, all ratings turn to “View”
automatically.
B TV Rating
Display the “TV Rating” screen.
• Using [K /L], select “TV Rating”.
V-Chip
MPAA Rating
TV Rating
New Password
L
D
Select
ENTER
View/Block
BACK
Back
• For the rating with sub categories,
press [K /L / s / B] and select the rating. Then
press [ENTER] and set to “View” or “Block”.
V-Chip
FV V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
6
ENTER
View/Block
BACK
Back
To exit the setup, press [SETUP].
<Selection>
TV-MA :
TV-14 :
TV-PG :
TV-G :
TV-Y7 :
TV-Y :
<Rating Category Explanations>
Mature audience only
Unsuitable for children under 14
Parental Guidance suggested
General Audience
Appropriate for children seven
and older
Appropriate for all children
<Selection>
FV :
V:
S:
L:
D:
<Rating Sub Category Explanations>
Fantasy Violence
Violence
Sexual Situation
Coarse Language
Suggestive Dialogue
NOTES:
• Press [ENTER].
V-Chip
FV V
S
L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
Select
S
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
To exit the setup, press [SETUP].
<Selection>
X:
NC-17 :
R:
4
Set “TV Rating”.
• Using [K /L], select the rating.
OPTIONAL SETTINGS
5
ENTER
View/Block
BACK
• When you select a rating and set it to “Block”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set “TV-MA” to “View”, all ratings turn to “View”
automatically.
Back
29
EN
C New Password
4
Display the “New Password” screen.
• Using [K /L], select “New Password”.
V-Chip
MPAA Rating
TV Rating
New Password
• Press [ENTER].
5
Change the password.
• Use Channel number buttons on the remote
control and enter the NEW 4-digit password.
• Enter password again in “Confirm password”
space.
V-Chip
Enter password.
Confirm password.
PIN Code
6
BACK
Back
To exit the setup, press [SETUP].
NOTES:
• Make sure to enter the exact same new password as the
“Confirm password.”. If they are different, the space is
cleared for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs or when you turn off the
power using a wall switch. If you forget the password,
unplug the power cord for 10 seconds to restore the password to 0000.
30
EN
HDMI AUDIO
Set the method of sound input for HDMI jack.
STILL
-
0
SCREEN
MODE
SETUP
ENTER
INFO
BACK
1
Display the setup screen.
2
OPTIONAL SETTINGS
• Press [SETUP].
The following setup screen is displayed.
Select “DETAIL” and press [ENTER] to confirm.
• Using [K /L], select “HDMI Audio” and press
[ENTER] to confirm.
Detail
Closed Caption
V–chip
HDMI Audio
3
Auto
Switch the HDMI Audio.
• Using [K /L], select the desired HDMI Audio,
then press [ENTER].
Detail
Closed Caption
V–chip
HDMI Audio
Auto
Digital
Analog
• Select “Auto” if you connected to both digital
device with HDMI jack and analog device for
audio sources. Digital audio input signal has
priority in this setting.
• Select “Digital” if you connected to digital
device with HDMI jack for digital audio input
signal.
• Select “Analog” if you connected to analog
device with analog jacks for analog audio input
signal.
4
To exit the setup, press [SETUP].
31
EN
MISCELLANEOUS
TROUBLESHOOTING GUIDE
Before calling for service, check the following chart again.
Symptom
32
EN
Remedy
No power
• Be sure the Power cord is connected to outlet.
• If a power failure occurs, unplug the power cord for 30 minutes
to allow the unit to reset itself.
No picture or sound
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Try to view other channels. It may be the problem on the broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on
again.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Try to view other channels. It may be the problem on the broadcasting station.
• Adjust the Color in the setup screen.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
• Adjust Contrast and Brightness in the setup screen.
• Try to view other channels. It may be the problem on the broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and
connection.
• Try to view other channels. It may be the problem on the broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Adjust Contrast and Brightness in the setup screen.
• Try to view other channels. It may be the problem on the broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and
connection.
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
• Try to view other channels. It may be the problem on the broadcasting station.
Picture blurred
• When the outside antenna is used, check the wire condition and
connection.
• Try to view other channels. It may be the problem on the broadcasting station.
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
• Try to view other channels. It may be the problem on the broadcasting station.
Bars on screen
• When the outside antenna is used, check the wire condition and
connection.
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
Remedy
Picture rolls vertically
• When the outside antenna is used, check the wire condition and
connection.
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
• Try to view other channels. It may be the problem on the broadcasting station.
Different color marks on screen
• Move the TV apart from electric appliances nearby. Turn off the
power and wait for about 30 minutes, then turn it on again.
• Try to view other channels. It may be the problem on the broadcasting station.
Poor reception on some channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and
connection.
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
• Try to view other channels. It may be the problem on the broadcasting station.
Picture OK, sound poor
• Electric waves may be interfered due to the electric appliances,
etc. nearby.
• Try to view other channels. It may be the problem on the broadcasting station.
No reception of digital signals
• Make sure that Autoscan in setup screen has been completed. It
will be required when you setup TV for the first time or when TV
is moved to a location where other channels are broadcast.
• The selected channel does not exist at that time. There are not
always minor-channels being broadcast.
• When Autoscan is interrupted and not completed, some channels will not be received. Make sure to complete Autoscan in the
setup screen.
MISCELLANEOUS
Symptom
The entered channel number changes • Many digital channels have alternate channel numbers. TV changes the
numbers automatically to the ones signifying the broadcasting stations.
automatically
These are the numbers used for analog broadcasts.
Remote control doesn’t work
• Check the antenna or cable connection to the main unit.
• Check the battery life of the remote control.
• Check if there is an obstacle between the sensor and the
remote control.
• Test the signal output. If OK, then possible remote sensor trouble. (Refer to “IR SIGNAL CHECK” on page 34.)
Problems on Closed Caption
Misspelled captions are displayed.
• Closed captioning production companies may broadcast programs without correcting the misspelling in a live broadcast.
Captions are not entirely displayed, or • Captions that are delayed a few seconds behind the actual dialogue
captions are delayed behind the diaare common for live broadcasts. Most captioning production compalogue.
nies can display a dialogue to a maximum of 220 words per minute. If
a dialogue exceeds that rate, selective editing is used to insure that
the captions remain up-to-date with the current TV screen dialogue.
Captions are displayed as a white
box.
No caption is displayed in the Closed
Caption-supported program.
• When electric waves are interfered due to buildings, weather
conditions etc., incomplete captions may be displayed.
• Broadcasting station may shorten the program to insert the
advertisement. The closed caption decoder cannot read the
information of the shortened program.
No caption is displayed when playing
the videotape containing captions.
• The videotape may be illegally copied, or the caption signal may
fail to be read while copying.
Black box is displayed in the screen.
• “Text” mode is selected for caption. Select “CC1”, “CC2”, “CC3”,
“CC4” or “Off”.
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels
may appear as a fixed point of blue, green or red. This is not to be considered a defect in the LCD screen.
33
EN
GLOSSARY
ATSC
Acronym that stands for Advanced
Television Systems Committee and
the name of the digital broadcasting
standards.
Aspect ratio
The width of a TV screen relative
to its height. Conventional TVs are
4:3 (in other words, the screen is
almost square); widescreen models are 16:9 (the screen is almost
twice as wide as its height).
Component video
This is a video signal format that
conveys each of three principal
colors of light (red, blue and
green) through different signal
lines. This allows the viewers to
experience picture colors as original as it is. There are several signal formats, including Y / Pb / Pr
and Y / Cb / Cr.
Dolby Digital
The system developed by Dolby
Laboratories to compress digital
sound. It offers you sound of
stereo (2ch) or multi-channel
audio (up to 5.1ch).
HDMI (High-Definition
Multimedia Interface)
Interface that supports all uncompressed, digital audio/video formats
including set-top box, DVD player or
digital television, over a single cable.
High Definition TV (HDTV)
Ultimate digital format that produces
high resolution and high picture quality.
LPCM
(Linear Pulse Code Modulation)
LPCM is a format that can have
up to 8 channels of audio. It is
mainly used in music production.
The format samples and captures
analog signals and transforms
them into digital signals without
compressing the sound data.
NTSC
Acronym that stands for National
Television Systems Committee
and the name of the current analog broadcasting standards.
Password
A stored 4-digit number that you
must provide in order to make settings for V-CHIP.
SAP
(Secondary Audio Program)
Second-audio channel delivered
separately from main-audio channel. This audio channel is used as
an alternate in bilingual broadcasting.
Standard Definition TV (SDTV)
Standard digital format that is similar to the NTSC picture quality.
S-Video
It delivers independently each signal of color(C) and luminance (Y)
to TV as video signals, so that
higher-quality picture will be
gained.
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
the TV with a soft cloth immersed in lukewarm
water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the TV. Such chemicals may
cause damage and discoloration to the exposed
surfaces.
LCD CLEANING
Wipe the LCD of the TV with a soft cloth. Before
cleaning the LCD, disconnect the power cord.
SERVICING
Should your unit become inoperative, do not try to
correct the problem by yourself. There are no user
serviceable parts inside. Turn off, unplug the power
cord and please call our help line mentioned on the
front page, to locate an Authorized Service Center.
34
EN
IR SIGNAL CHECK
If the remote control doesn’t work properly, You can
test if the remote control sends out the infrared signal with an AM radio or a digital camera (including
built-in camera of cellular phone). It will help to
define the cause of malfunction.
• With an AM radio:
Tune an AM radio to a station
with no broadcasting. Press any
button on remote control toward
the radio. Sound will be fluttering
when you press any button and
the radio receives the signal. This
means the remote control unit is
working.
• With a digital camera (including builtin camera of cellular phone):
Direct a digital camera to remote control, press and hold any button on
remote control. If infrared light appears
through digital camera, the remote
control unit is working.
SPECIFICATIONS
Closed Caption
System:
ATSC
NTSC-M
TV Standard
§15.119/FCC (Analog CC)
§15.122/FCC (Digital CC)
Channel coverage (ATSC/NTSC)
VHF:
2 ~ 13
UHF:
14 ~ 69
CATV:
2 ~ 13, A ~ W,
W+1 ~ W+94,
A-5 ~ A-1, 5A
Tuning System:
Channel frequency
synthesized tuning system
Channel access:
Direct access keyboard,
Programmable scan,
and Up/down
Terminals
Antenna input:
VHF/UHF/CATV
75 ohm unbalanced
(F-type)
S-Video input:
Mini DIN 4-pin jack x 2
Video input:
RCA jack x 2
Audio input:
RCA jack (L/R) x 4
Component Video/Audio input:
One pin jack (Y) / 1Vpp x 2
Two pin jacks (Pb/Pr) / 700mVpp x 4
RCA jack (L/R) x 4
HDMI / Audio input:
HDMI jack
RCA jack (L/R) x 2
Coaxial digital audio output:
One pin jack, 500mVpp
Analog Audio output:
RCA jack (L/R) x 2
Stereo Sound System Speaker
ELECTRICAL SPECIFICATION
Sound output:
5W, 8 ohm x 2
OTHER SPECIFICATIONS
Remote control:
Digital encoded
infrared light system
Operating
temperature:
5°C to 40°C
(41°F to 104°F)
Power requirements: AC120V, 60Hz
Power consumption
(Maximum):
205W
LCD:
37" wide XGA panel
(1,366 x 768 pixels)
Dimensions:
<Without stand>
H : 26-9/16" (674mm)
W: 37-5/16" (948mm)
D : 4-12/16" (120mm)
<With stand>
H : 28-5/16" (718.5mm)
W: 37-5/16" (948mm)
D : 12-13/16" (325mm)
Weight:
52.8 lbs. (24kg)
MISCELLANEOUS / SPECIFICATIONS
GENERAL SPECIFICATIONS
Television system:
• Designs and specifications are subject to change without notice and without our legal obligation.
• If there is a discrepancy between languages, the default language will be English.
35
EN
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in CANADA in the event of defect in materials or workmanship
as follows:
DURATION :
PARTS :
LABOR :
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Certain parts and LCD image burn-in are not covered under this
warranty.
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS :
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO
OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product
not purchased and used in CANADA.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product
not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling,
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office
use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE
OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL
OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN CANADA.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE
CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF
NO PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS
WILL BE CHARGED.
ATTENTION :
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging
or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI CORP. will not
reimburse you for any service done by unauthorized service providers without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,
please contact to us at:
FUNAI CORPORATION
Customer Service
Tel: 1-800-474-0045
http://www.funai-corp.com
19900 Van Ness Avenue, Torrance, CA 90501
Printed in China
1EMN21883
L5001CB ★★★★
Download PDF

advertising