E6150UD_ENSP.qx33
05.4.5 14:24
Page 1
Owner’s Manual
Please read before using this unit.
DVD/CD Player
MSD125
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
If your TV has AUDIO/VIDEO input jacks, see the section
“Connections” on page 6. If not, it is still possible to connect
this unit to your TV by using a STEREO AUDIO/VIDEO RF
Modulator (commercially available.) In this case, follow the
instructions below.
1) Connect the AUDIO/VIDEO output jacks of this unit to the
AUDIO/VIDEO input jacks of your RF Modulator by audio and
video cables.
2) The antenna input jack of your TV may have been already occupied. If so, disconnect the RF cable from your TV, then connect
the RF cable to your RF Modulator (usually marked “ANT IN”.)
3) Connect your RF modulator to your TV by another RF cable.
4) Set your RF modulator’s channel 3/4 switch to either 3 or 4,
whichever the TV channel is least used in your area. If your RF
modulator has a Modulator/Antenna switch, set it according to
your RF modulator’s manual.
5) Turn on your TV and choose the same channel as you set the
RF modulator’s channel 3/4 switch to.
For more details, follow the instructions supplied with the RF
Modulator.
2
3
4
4
4
4
4
4
4
5
5
5
Setup
■ Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection to a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection to an Audio System . . . . . . . . . . . . . . . . . . .
Rear Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ About the Remote Control . . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Batteries for the Remote Control . . . . . . . .
6
6
7
7
8
8
8
Functions
Hint
■ Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
■ On-Screen Display. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
■ Search Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Title / Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . 11
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
■ Marker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
■ Repeat / Random / Programmed Playback . . . . . . . . 12
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Repeat A-B Playback. . . . . . . . . . . . . . . . . . . . . . . . . . 12
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Programmed Playback. . . . . . . . . . . . . . . . . . . . . . . . . 12
■ Special Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Camera Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Black Level Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Stereo Sound Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Virtual Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
■ DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LANGUAGE Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DISPLAY Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
AUDIO Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PARENTAL Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OTHERS Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reset to the Default Setting
(except for PARENTAL Setting) . . . . . . . . . . . . . . . . . . 17
• The quality of picture may become poor if the unit is connected
Information
Cable
Signal
(Back of this unit)
Antenna
AUDIO OUT
L
Y
CR /PR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
(Back of TV)
Stereo Audio/Video RF Modulator
(commercially available)
AC 120V ANT IN
CHANNEL
3
4
TO TV
VIDEO
AUDIO
R
L
COAXIAL
R
VIDEO
OUT
CB /PB
S-VIDEO
OUT
1
Audio/Video
Cables
(Supplied)
2
Antenna in jack
3
RF Cable (Not supplied)
to an RF Modulator.
If you need additional operating assistance after
reading this owner’s manual, please call
TOLL FREE : 1-800-605-8610
or visit our web site at http://www.funai-corp.com
■
■
■
■
Troubleshooting Guide
Specifications . . . . . . .
Language List . . . . . . .
Limited Warranty . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
17
18
18
18
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Quick Use Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Setup
Connecting to RF Modulator
Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Avoid the Hazards of Electrical Shock and Fire . . . . . . .
Moisture Condensation Warning . . . . . . . . . . . . . . . . . .
About Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notice for Progressive Scan Outputs . . . . . . . . . . . . . . .
Symbols Used in This Manual . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
■ About the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unplayable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functions
Owner's Manual
Precautions
Information
• Remote control • Audio/Video cables • Owner’s Manual
(NB070UD) with
(WPZ0102TM015/ (1VMN20430)
two AA batteries
WPZ0102LTE01/
WPZ0102CAB01)
Precautions
Table of Contents
Español
Supplied Accessory
E6150UD_ENSP.qx33
05.4.5 14:24
Page 2
Precautions
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
Precautions
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible
eye injury.
CAUTION:
CAUTION:
LOCATION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO
BEAM.
INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification
is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
For Customer Use:
Read carefully the information located at the bottom of this unit and enter below the Serial No. Retain this information for
future reference.
Model No. _____________________
Serial No. _____________________
–2–
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 3
1) Read Instructions - All the safety and operating instructions should be read before the product is operated.
2) Retain Instructions - The safety and operating instructions should be retained for future reference.
3) Heed Warnings - All warnings on the product and in
the operating instructions should be adhered to.
4) Follow Instructions - All operating and use instructions
should be followed.
5) Cleaning - Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6) Attachments - Do not use attachments not recommended by the product manufacturer as they may
cause hazards.
7) Water and Moisture - Do not use this product near
water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near
a swimming pool; and the like.
8) Accessories - Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the
product should follow the manufacturer’s instructions, and should use a
mounting accessory recommended
by the manufacturer.
9) A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to
overturn.
10) Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and
these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have been
adhered to.
11) Power Sources - This product should be operated only
from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local
power company. For products intended to operate from
battery power, or other sources, refer to the operating
instructions.
12) Grounding or Polarization - This product may be
equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is a
safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
13) Power-Cord Protection - Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
product.
14) Lightning - For added protection for this product during
a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the product due to
lightning and power-line surges.
15) Power lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any
kind into this product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on the product.
18) Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
19) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions
as an improper adjustment of other controls may
result in damage and will often require extensive
work by a qualified technician to restore the product
to its normal operation,
e) If the product has been dropped or damaged in any
way.
f ) When the product exhibits a distinct change in performance - this indicates a need for service.
20) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
22) Heat - The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
–3–
EN
Precautions
IMPORTANT SAFEGUARDS
E6150UD_ENSP.qx33
05.4.5 14:24
Page 4
Installation Location
Symbols Used in This Manual
Precautions
For safety and optimum performance of this unit:
• Do not stand the unit up vertically. Install the unit in
a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit
directly on top of the TV.
• Shield it from direct sunlight and keep it away from
sources of intense heat. Avoid dusty or humid
places. Avoid places with insufficient ventilation for
proper heat dissipation. Do not block the ventilation
holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.
• Be sure to remove the disc and unplug the AC
power cord from the output before carrying the unit.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Moisture Condensation Warning
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. Do not use this unit at least for 2 hours
until its inside gets dry.
About Copyright
Unauthorized copying, broadcasting, public
performance and lending of discs are prohibited.
This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly
is prohibited.
Notice for Progressive Scan Outputs
Consumers should note that not all high definition television sets are fully compatible with this product and may
cause artifacts to be displayed in the picture. In case of
picture problems with 525 progressive scan output, it is
recommended that the user switch the connection to the
‘standard definition’ output. If there are questions regarding your TV set compatibility with this 525p DVD player,
please contact our customer service center.
The following symbols appear in some headings in this manual.
DVD-V
: Description refers to playback of DVD-Video discs.
CD
: Description refers to playback of Audio CDs.
Maintenance
SERVICING
¡Please refer to relevant topics on the “Troubleshooting
Guide” on page 17 before returning the product.
¡If this unit becomes inoperative, do not try to correct
the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug,
and please call our help line mentioned on the front
page to locate an Authorized Service Center.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
¡Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog records.
CLEANING THE DISC LENS
¡If this unit still does not perform properly although you
refer to the relevant sections and to “Troubleshooting
Guide” in this Owner’s Manual, the laser optical pickup
unit may be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the laser
optical pickup unit.
DISC HANDLING
¡When you handle a disc hold it by its edge and try not
to touch the surface of the disc.
¡Always store a disc in its protective case when it is
not used.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
–4–
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 5
About the Discs
Playable Discs
Playable
discs
Mark (logo)
DVD-Video
Region code
Recorded
signals
Disc size
Digital video
(MPEG2)
12 cm
or
8cm
Example
12 cm
or
8cm
Example
Digital audio
Disc types
or
DVD-RW
DVD-R
-
* 1, 3, 4, 5,
6, 7, 9, 10
DVD+RW
DVD+R
* 1, 3, 4, 5,
6, 8, 9, 10
Title 1
Precautions
* 1, 2, 4,
6, 10
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
-
Audio CD
* 4, 6, 10
-
CD-RW
CD-R
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
* 4, 5, 6
9, 10
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot
be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Discs recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the
recorder or special properties of discs.
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not
play them back. Even if they are played back, the sound or video quality will be compromised.
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with the
DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be
played back at all or normally (the picture or sound may not be smooth, etc.).
*9: If there is too much recording space left on a disc (the used portion is less than 55 mm across), it may not play
back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it
correctly.
Unplayable Discs
¡ NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers
¡ On the following disc, the sound MAY NOT be heard.
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
¡ Any other discs without compatibility indications
–5–
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 6
Setup
Connections
If your TV has AUDIO/VIDEO input jacks, see the following instructions. If not, see the section “Connecting to
RF Modulator” on the front page.
Connection to a TV
Basic Audio
TV
Method 1
Method 2
Method 3
Good picture
Better picture
Best picture
COMPONENT
VIDEO IN
AUDIO IN
L
R
VIDEO IN
Y
S-VIDEO IN
Y
PB
CB
or
PR
Setup
This unit
AUDIO OUT
S-Video
cable
(commercially
available)
Video
cable
(supplied)
Audio cable
(supplied)
CR
Component Video cables
(commercially available)
L
Y
AUDIO OUT
L
Y
CR /PR
CR /PR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
COAXIAL
R
VIDEO
OUT
CB /PB
S-VIDEO
OUT
R
(Analog) AUDIO OUT
S-VIDEO
OUT
VIDEO
OUT
S-VIDEO OUT
VIDEO OUT
VIDEO
OUT
CB /PB
S-VIDEO
OUT
COMPONENT VIDEO OUT
Hint
• Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted
due to the copy protection system.
• When progressive scanning mode is selected, no video signal will be output from the VIDEO OUT or S-VIDEO OUT jack.
If your TV is compatible with 525p (480p) progressive scanning and you want to
enjoy that high quality picture;
[DVD]
OPEN/CLOSE
PLAY
STANDBY-ON
y
Set “PROGRESSIVE” to “ON” in the Display menu. P.SCAN light will light up on the front of the unit.
Details are on page 15.
If your TV is not compatible with progressive scanning;
STOP
more than 5 seconds
[Interlace mode]
Use this unit in interlace mode. Make sure “PROGRESSIVE” is set to “OFF” and P.SCAN light on the
front of the unit is off. Progressive scanning mode can be set to off either in the Display menu or by
pressing and holding [PLAY B] on the front of the unit for more than 5 seconds. Detailes are on page 15. [Progressive scanning mode]
After you have completed connections
• Hit the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually near channel 0) for viewing the picture from this unit. If the picture does not appear, also refer to the manual
accompanying your TV.
INPUT MODES FOR COMMON TV BRANDS (Example)
• Listed below are inputs for common brand name TV’s.
Admiral:
AUX
Curtis Mathis:
LINE1, LINE2, 00, 90, 91, 92, 93
GE:
INPUT, TV/VCR, 00, 90, 91, 92, 93
Hitachi:
INPUT, AUX
JVC:
A/V CHANNEL, INPUT1, SVIDEO,
INPUT2
Kenwood:
AUX
LXI-Series:
00
Magnavox:
AUX CHANNEL
Panasonic:
TV/VIDEO
RCA:
INPUT, TV/VCR, 00, 90, 91, 92, 93
Samsung:
Sanyo:
Sharp:
Sony:
Toshiba:
Zenith:
–6–
TV/VIDEO
VIDEO
00
VIDEO1, VIDEO2, VIDEO3
TV/GAME
00
EN
E6150UD_ENSP.qx33
05.4.5 14:41
Page 7
Connection to an Audio System
Method 1
Method 2
Dolby Digital decoder,
MD deck or DAT deck
Stereo system
Analog audio
input jacks
AUDIO
L
Digital audio
input jack
COAXIAL
R
Audio Coaxial
Digital cable
(commercially
available)
Audio cable
(supplied)
(Analog)
AUDIO OUT
AUDIO OUT
L
DIGITAL
AUDIO OUT
Setup
This unit
DIGITAL
AUDIO OUT
COAXIAL
R
SETUP > AUDIO menu >
DOLBY DIGITAL
PCM
* To complete these settings, refer to pages 14-15.
SETUP > AUDIO menu >
Setting
Connection
DOLBY DIGITAL
Connecting to a Dolby Digital decoder
BITSTREAM
for Dolby Digital audio output.
Connecting to the other equipment (an MD deck or
PCM
DAT deck etc.) without Dolby Digital decoder.
Setting
Connection
Connecting to Stereo System.
Hint
* To complete these settings, refer to pages 14-15.
• Playing a DVD using incorrect settings may generate noise
distortion and may also damage the speakers.
Hint
• The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or
DAT deck.
• By hooking this unit up to a Multi-channel Dolby Digital decoder,
you can enjoy high-quality Dolby Digital 5.1 channel surround
sound as heard in the movie theaters.
• Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
Rear Terminals
COMPONENT VIDEO OUT jacks
Connect optional component
video cables here through the
component video input jacks of
a television.
AUDIO OUT jacks
Connect the supplied audio cable (red/white)
here through the audio input jacks of a TV or
other audio equipment.
AUDIO OUT
L
Y
CR /PR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
COAXIAL
R
DIGITAL AUDIO OUT COAXIAL jack
Connect an optional coaxial digital audio
cable here through the coaxial digital audio
input jack of a decoder or audio receiver.
VIDEO
OUT
CB /PB
S-VIDEO
OUT
S-VIDEO OUT jack
Connect an optional S-Video
cable here through the S-video
input jack of a TV.
VIDEO OUT jack
Connect the supplied video cable
(yellow) here through the TV’s
video input jack.
–7–
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 8
About the Remote Control
Remote Control
Disc
Button
DVD-V
(Alphabetical order)
STANDBY–ON
OPEN/CLOSE
DISPLAY
SEARCH
MODE
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
0
+10
AUDIO
CD
• To select chapter or title
directly.
• To select track directly.
ENTER
• To move the cursor and
determine its position.
• To move the cursor and
determine its position.
A-B
• To repeat between your
chosen point A and B.
• To repeat between your
chosen point A and B.
SUBTITLE
ANGLE
REPEAT
CLEAR
A-B
PAUSE
0
+10
SKIP
SLOW
PLAY
REV
ANGLE
• To select camera angles on
a disc.
AUDIO
• To select audio languages on • To select STEREO,
a disc.
L-ch or R-ch.
• To clear the markers.
• To clear the markers.
• To remove status number
in program input.
• To clear the numbers
• To clear the numbers
entered incorrectly.
entered incorrectly.
• To cancel the point for A-B
• To cancel the point for A-B
repeat.
repeat.
FWD
STOP
SETUP
MODE
TOP MENU
MENU
ENTER
ZOOM
RETURN
CLEAR
Setup
DISPLAY
REV
Installing the Batteries
for the Remote Control
Install two AA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote
control.
1
FWD
MENU
MODE
OPEN/CLOSE
• To display the current disc
mode.
• To display the current disc
mode.
• To search forward/backward
through a disc.
• To begin slow forward
/reverse playback during
the pause mode.
• To search forward/backward
through a disc.
• To call up the Menu
on a disc.
• To arrange the playing
• To set black level on/off.
• To set virtual surround on/off. order or play randomly.
• To set virtual surround on/off.
• To open or close the disc
tray.
• To open or close the disc
tray.
• To pause disc playback.
• To advance playback
one frame at a time.
• To pause disc playback.
• To begin disc playback.
• To begin disc playback.
• To turn the unit on or off.
• To turn the unit on or off.
REPEAT
• To play a chapter or title
repeatedly.
• To play a track or disc
repeatedly.
RETURN
• To return to the previous
operation in menu.
• To return to the previous
operation in menu.
PAUSE
2
PLAY
STANDBY–ON
3
Keep in mind the following when
using the remote control:
• Make sure that there is no obstacle
between the remote control and the
remote sensor on the unit.
• The maximum operable ranges
from the unit are as follows.
- Beeline: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m)
within 15°
- Below: approx. 10 feet (3m)
within 30°
SEARCH
MODE
SETUP
SKIP
STOP
SUBTITLE
P.SCAN
OPEN/CLOSE
PLAY
STOP
STANDBY-ON
y
IR
SENSOR
TOP MENU
ZOOM
• To search track.
• To search chapter, title or time. • To search time.
• To set or search the
• To set or search the
markers.
markers.
• To call up the DVD setup
menu.
• To call up the DVD setup
menu.
• To skip chapters.
• To skip tracks.
• To stop playback.
• To stop playback.
• To select subtitles on a disc.
• To call up the Top Menu
on a disc.
• To magnify part of a picture.
(x2/x4)
–8–
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 9
Functions
Operations described after this section are mainly based on the remote control use. Some operations can be carried out on main unit.
Playback
Before: Turn on the TV, amplifier and
any other equipments which are connected to this unit. Make sure the TV
and audio receiver (commercially available) are set to the correct channel.
OPEN/CLOSE
STANDBY–ON
2
2
STANDBY–ON
1
4
To stop
playback
SEARCH
MODE
1
2
3
4
5
6
7
8
9
0
+10
• A “prohibited icon” may appear at the top-right on the TV
screen when the operation is prohibited by the disc or this unit.
• Some DVDs may start playback from title 2 or 3 due
to specific programs.
• During the playback of a two-layered disc, pictures may stop
for a moment. This happens while the 1st layer is being
switched to the 2nd layer. This is not a malfunction.
ANGLE
REPEAT
CLEAR
A-B
SKIP
PAUSE
3
4
SLOW
PLAY
REV
TIP:
You can change the On-Screen language in “PLAYER MENU”
setting. (Refer to page 14.)
FWD
STOP
SETUP
TOP MENU
MENU
DVD menu
Fast Forward/Reverse Search
Some discs contain menus which allow you to customize
K / L / s / B] to select an item, then
DVD playback. Press [K
press [ENTER] (or [PLAY B]).
Calling Up a Menu Screen during Playback
• Hit [MENU] to call up the DVD menu.
• Hit [TOP MENU] to call up the title menu.
DVD-V
CD
Press [FWD g] or [REV h] repeatedly during playback to select the required forward or
reverse speed.
To continue playback, hit [PLAY B].
E1
Hint
Hint
• For DVDs, fast forward or reverse search speed is different depending on
the disc. Approximate speed is 1(x2), 2(x8), 3(x20), 4(x50) and 5(x100).
• For Audio CDs, approximate speed is 1(x2), 2(x8) and 3(x30).
• Menu operations may vary depending on the disc. Refer to the
manual accompanying the disc for more details.
Slow Forward/Slow Reverse
Resume
DVD-V
CD
Hit [STOP C]. Resume message will appear on the TV
screen.
Hit [PLAY B], playback will
resume from the point at which
playback was stopped.
Press [FWD g] or [REV h] repeatedly during the pause mode to select the required forward or reverse speed.
To continue playback, hit [PLAY B].
Resume ON
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
1
Hint
• Slow forward or reverse speed is different depending on the disc.
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).
• Set “STILL MODE” to “FIELD” in the Display menu if pictures in the
slow playback mode are blurred. (Refer to pages 14-15.)
Hint
• To cancel resume, hit [STOP C] one more time during the stop
mode.
• The resume information will be kept even when the power is turned
off.
Paused and Step-by-Step Playback
DVD-V
Lights up
when power
is on.
1 Hint
AUDIO
STOP
PLAY
DVD-V
1 3 4 1
IR
SENSOR
OPEN/CLOSE
DISPLAY
SUBTITLE
To start
playback
STANDBY-ON
P.SCAN (Progressive Scan) light
Lights up when the “PROGRESSIVE”
is “ON”. Details are on page 15.
Insert a disc with
label facing up.
3
STOP
y
CD
1
PLAY
Zoom
DVD-V
Hit [ZOOM] repeatedly during playback to select the
required zoom factor: x2, x4 or OFF.
x2
x4
CD
Hit [PAUSE F] during playback.
To continue playback, hit [PLAY B].
K / L / s / B] to slide the zoomed picture across the
Press [K
screen.
To exit zoom function, hit [ZOOM] repeatedly to select OFF.
DVD-V
The disc goes forward by one frame each time [PAUSE F]
is hit during the pause mode.
To continue playback, hit [PLAY B].
Hint
Hint
• On DVDs, set “STILL MODE” to “FIELD” in the Display menu if pictures in the pause mode are blurred. (Refer to pages 14-15.)
• Zooming function does not work while the disc menu is showing up.
• x4 zoom is not available on some discs.
• The picture may be distorted when you press [PAUSE k] or
[REV h] repeatedly in the zoom mode.
• It may take several seconds to slide the zoomed picture.
–9–
EN
Functions
DVD-V
P.SCAN
OPEN/CLOSE
E6150UD_ENSP.qx33
05.4.5 14:24
Page 10
On-Screen Display
You can check the information about the current disc by hitting [DISPLAY] on the remote control.
DVD-V
CD
DISPLAY
Angle icon, appears only when available on the DVD
Current playback status
DISPLAY
1
Current playback status
1
Remaining time of the current chapter
DISPLAY
CH(Chapter):
Current chapter number / Total chapters
2
DISPLAY
1/3
4/12 0:13:45 - 0:45:40
0:00:00 - 1:23:45
Remaining time of the current title
Elapsed time of the current title
DISPLAY
TT(Title):
Current title number / Total titles
T
T
Remaining time of the current track
Elapsed time of the current track
TR(Track):
Current track number / Total tracks
ALL:
Current track number / Total tracks
Current repeat setting appears only
when the repeat setting is active
T: Track repeat
A: All Tracks repeat
A B: A-B repeat
Remaining time of the entire disc
Elapsed time of the entire disc
3
DISPLAY
3
T
11/16 0:00:00 - 0:03:30
Elapsed time of the current chapter
2
4/12 0:03:21 - 0:02:15
L1
Layer numbers, appears only when
playing a two-layered Disc
L0: Layer 0 is playing
L1: Layer 1 is playing
Hint
• When you are playing a disc in PROGRAM or RANDOM mode,
PROGRAM (or RANDOM) will be displayed instead of 2 .
Functions
Current repeat setting appears only
when the repeat setting is active
C: Chapter repeat / T: Title repeat /
A B: A-B repeat
BIT RATE: The amount of audio and
video data currently being read
DISPLAY
4
– 10 –
EN
E6150UD_ENSP.qx33
05.4.5 15:08
Page 11
Search Function
Track Search
Title / Chapter Search
CD
Time Search
DVD-V
Using [SEARCH MODE]
1
SEARCH
MODE
DVD-V
Using [SEARCH MODE]
1
SEARCH
MODE
/29
CD
1
PLAY
TOTAL 1:29:00
/12
SEARCH
MODE
1
2
3
4
5
6
7
8
9
0
+10
/29
Hit once for the chapter search.
Hit twice for the title search.
2
Within 30 seconds.
1
2
3
4
5
6
7
Using [SKIP H , G ]
1
3
5
6
7
8
9
TOTAL 1:29:00
Within 30 seconds.
Hint
Using [SKIP H , G ]
1
Current Chapter
(CH)
PLAY
SKIP
Current Track
(TR)
SKIP
+10
2
4
Within 30 seconds.
PLAY
SKIP
9
0
1
0
• For the disc with less than 10 tracks, hit
the track number directly.
• For discs with more than 10 but less
than 99 tracks, to play single-digit track,
hit [0] first, then the track number (e.g.
for track 3, hit [0], [3]). To play a doubledigit track, hit the track number.
8
2
/12
TR 1 TR 2 TR 3 TR 4
SKIP
CH 1 CH 2 CH 3 CH 4
SKIP
SKIP
or
Current Title
(TT)
SKIP
• When there is no need to enter a number,
“0” appears automatically.
For example, “0 : 0-: --” appears in the
Time Search display if the total time of the
title or track is less than 10 minutes.
• Hit [CLEAR] to erase the incorrect input at
step 2).
Functions
2
Hit repeatedly until the
Time Search display
appears.
TT 1 TT2 TT3 TT4
SKIP
(If the disc has no chapters)
Hint
Hint
• [+10] button can also bring the Track Search
display, except for the disc with less than 10
tracks. For such a disc, track search can be
done by just hitting the track number.
• Depending on the disc being played, this
function can also be performed by directly
entering the desired chapter number with
the Number buttons. Refer to the manual
accompanying the disc.
Marker Setup
DVD-V
CD
This feature allows you to assign a specific
point on a disc to be called back later.
To set a marker
1
To return to the marker
later
1
To exit the marker display
1
RETURN
PLAY
PLAY
SEARCH
MODE
SEARCH
MODE
Hit repeatedly until the
marker display
appears.
Hit repeatedly until
the marker display
appears.
• Opening the disc tray or turning off the
power will erase all markers.
• Selecting “AC” at step 2) in the section “To
set a marker” will also erase all markers.
• To clear a marker, select the marker to be
cleared at step 2) in the section “To return
to the marker later,” and then hit [CLEAR].
2
or
2
Hint
or
3
ENTER
3
ENTER
at the desired marker
•Playback will restart from the specific point
which you set.
– 11 –
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 12
Repeat / Random / Programmed Playback
Repeat Playback
DVD-V
Repeat A-B Playback
CD
DVD-V
Repeat function is available only during
playback.
Programmed Playback
CD
CD
1
You may determine the order in which
tracks will play.
PLAY
A-
1
PLAY
1
STOP
A-B
CD-DA
at your desired starting point (A)
REPEAT
TOTAL 0:00:00
MODE
ENTER
2
Each time you hit [REPEAT], repeat
function changes as example below.
A-B
A-B
Hit once.
<Example: CD>
2
at your desired end point (B)
DVD-V
TOTAL 1: 03: 30
or
CHAPTER (current chapter repeat)
1
5
10
11
12
17
22
• Point B should be in the same title or
track as point A.
1/4
TITLE
(current title repeat)
OFF
(repeat off)
TRACK
(current track repeat)
• To exit the sequence, hit [A-B] so that
OFF appears.
• To cancel Point A, hit [CLEAR].
• This function does not work in the other
repeat modes.
ALL
(entire disc repeat)
Random Playback
OFF
(repeat off)
CD
Hint
ENTER
• Up to 99 tracks can be
ordered.
• If eight or more tracks were in a
program, use [SKIP H, G]
to see all the tracks.
3
Functions
This function shuffles the playing
order of tracks instead of playback
in the sequence.
Hint
• Repeat setting will be cleared when moving to another title, chapter, or track.
• Repeat playback may not function with
some discs or during repeat A-B playback.
3:30
5:10
4:20
3:00
3:20
4:10
2:50
2/3
PLAY
Hint
CD
1
STOP
• Hit [CLEAR] at step 2) to erase the most
recently entered track.
RANDOM
CD-DA
TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
MODE
PLAY
Hit twice.
<Example: CD>
2
PLAY
Hint
• To repeat the current track in the random
selections, hit [REPEAT] repeatedly until
“
TRACK” appears during playback.
• To repeat the entire random selections, hit
[REPEAT] repeatedly until “
ALL”
appears during playback.
– 12 –
• To erase all programmed tracks at once,
select “ALL CLEAR’’ and hit [ENTER] at
step 2).
• While a program is being played back,
[STOP C] works as follows;
⇒Hit [STOP C] and [PLAY B] next, so
that the programmed playback restarts.
⇒Hit [STOP C] twice and [PLAY B] next,
so that playback restarts from the first
track in the original order. However, your
programmed playback can be restarted
when you follow the above steps. (Your
programs are still stored until either the
disc tray is open or power is turned off.)
• To repeat the current track in the program,
hit [REPEAT] repeatedly until “
TRACK’’
appears during playback.
• To repeat the entire program, hit [REPEAT]
repeatedly until “
ALL’’ appears during
playback.
EN
E6150UD_ENSP.qx33
05.4.5 15:09
Page 13
Special Settings
Subtitle Language
Audio Language
DVD-V
Stereo Sound Mode
DVD-V
CD
This unit allows you to select a subtitle
language (if available) during DVD playback.
This unit allows you to select an audio
language (if multiple languages are
available on disc) during DVD playback.
1
1
This unit allows you to select a sound
mode during CD playback.
1
PLAY
STEREO
PLAY
PLAY
1.ENG/6
1.ENG Dolby D 3/2.1ch 48k/3
AUDIO
AUDIO
Each time you hit [SUBTITLE], subtitle
language changes as example below.
Each time you hit [AUDIO], audio
language changes as example below.
ENG
(English subtitles)
ENG
(English audio)
FRE
(French subtitles)
SPA
(Spanish audio)
Each time you hit [AUDIO], sound
mode changes as example below.
STEREO (right and left channels
are active)
(left channel is active)
L-ch
...
...
OFF
(no subtitles)
To set subtitle ON/OFF
(French audio)
FRE
DVD-V
DVD-V
PLAY
1.ENG/6
SUB TITLE
2
OFF
Virtual Surround
Camera Angles
1
(right channel is active)
R-ch
Some DVD discs may
contain scenes which have
been shot simultaneously
from various angles. You can change
the camera angle if the (
) icon
appears on the screen. If the “ANGLE
ICON” setting is “OFF” in the OTHERS
menu, the (
) icon will not appear.
(Refer to pages 14-16.)
CD
You can enjoy stereophonic virtual
world on your existing 2 channel stereo
system.
1
PLAY
OFF
MODE
Hit twice
(once for CD)
1
PLAY
Hint
• If your language is not shown after pressing [AUDIO] or [SUBTITLE] several times,
the disc may not have that language.
However, some discs allow audio language
or subtitle language setting on the disc
menu. (Operation varies depending on the
disc, so refer to the manual along with the
disc.)
• When “NOT AVAILABLE” appears on the
TV screen, it means no subtitle is recorded
on the scene.
• If you choose a language that has three-letter-language code, the code will be displayed every time you change the subtitle
language setting. If you choose any other
languages, ‘---’ will be displayed instead.
(Refer to page 18.)
1/8
2
ENTER
1
ANGLE
1: Natural effect.
2: Emphasized effect.
OFF: No effects (original sound).
Black Level Setting
DVD-V
Adjust the Black Level Setting to make
the dark areas of the TV picture brighter.
1
PLAY
ON
3
RETURN
Hint
For CD playback only
• Virtual Surround will not be effective if the
sound mode is set to something other than
STEREO. Refer to “Stereo Sound Mode”.
MODE
2
ENTER
OFF
ON: Makes the dark areas brighter.
OFF: Shows the original picture as recorded.
3
RETURN
– 13 –
EN
Functions
SUB TITLE
E6150UD_ENSP.qx33
05.4.5 14:24
Page 14
DVD Setup
Q UICK SETUP Men u
You can select the “PLAYER MENU”, “TV ASPECT”, “PROGRESSIVE” or “DOLBY DIGITAL” from the
QUICK SETUP menu quickly.
1
2
SETUP
or
STOP
Select the desired item.
<SETUP MENU>
Confirm that “QUICK” is selected.
ENTER
SETUP
QUICK
SETUP
PLAYER MENU
TV ASPECT
PROGRESSIVE
DOLBY DIGITAL
QUICK
CUSTOM
INITIALIZE
A Step 5)
P14
P15
P15
P15
ENGLISH
4:3 LETTER BOX
OFF
BITSTREAM
ENTER
B Step 5)
B Step 5)
C Step 5)
• Refer to the sections “PLAYER MENU”, “TV ASPECT”,
“PROGRESSIVE” or “DOLBY DIGITAL” on page 14 or 15.
CUSTOM Men u
You can change the settings of the unit.
• QUICK on pages 14-16 indicates DVD Setup menus also accessible from the QUICK SETUP menu.
1
2
SETUP
STOP
<SETUP MENU>
ENTER
or
Select the desired item.
Functions
Select “CUSTOM”.
SETUP
ENTER
SETUP
QUICK
CUSTOM
INITIALIZE
SETUP
LANGUAGE
DISPLAY menu
SETUP
AUDIO menu
SETUP
DISPLAY
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
QUICK
CUSTOM
INITIALIZE
LANGUAGE menu
SETUP
3
or
AUDIO
PARENTAL menu
SETUP
PARENTAL
OTHERS menu
SETUP
OTHERS
PASSWORD
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ORIGINAL
OFF
ENGLISH
ENGLISH
TV ASPECT
STILL MODE
PROGRESSIVE
page 14 A
A
4:3 LETTER BOX
AUTO
OFF
DRC
DOWN SAMPLING
DOLBY DIGITAL
page 15 B
ON
ON
BITSTREAM
page 15 C
ANGLE ICON
AUTO POWER OFF
Please enter a 4-digit password.
page 16 D
ON
ON
page 16 E
LANGUAGE Setting
Follow steps 1) to 3) in the “CUSTOM Menu” section above.
4
5
Select the desired item.
Select the desired language.
ENTER
6
To exit the menu.
ENTER
SETUP
or
or
LANGUAGE menu
SETUP
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
LANGUAGE
ORIGINAL
OFF
ENGLISH
ENGLISH
AUDIO ∗1 ∗2
(Default: ORIGINAL)
Sets the audio language.
AUDIO
ORIGINAL
ENGLISH
FRENCH
SUBTITLE: ∗1 ∗2
(Default: OFF)
Sets the subtitle language.
SUBTITLE
OFF
ENGLISH
FRENCH
DISC MENU: ∗1
(Default: ENGLISH)
Sets the language in DVD
menu.
DISC MENU
ENGLISH
FRENCH
SPANISH
PLAYER MENU: QUICK
(Default: ENGLISH)
Sets the language for the
On-Screen Display.
PLAYER MENU
ENGLISH
FRANCAIS
ESPAÑOL
– 14 –
Hint
∗1
• Language options are not available
with some discs.
• If OTHER is selected in the AUDIO,
SUBTITLE or DISC MENU screen,
press four-digit number to enter the
code for the desired language. (Refer
to the language code list on page 18.)
• Only the languages supported by the
disc can be selected.
∗2
• Language setting for Audio and
Subtitle are not available with some
discs. Then hit [AUDIO] and
[SUBTITLE]. Details are on page 13.
EN
E6150UD_ENSP.qx33
B
05.4.5 14:24
Page 15
DISPLAY Setting
You can change the display functions. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
5
Select the desired item.
TV ASPECT: QUICK
(Default: 4:3 LETTER BOX)
See Hint to the right.
TV ASPECT
4:3 LETTERBOX
AUTO
STILL MODE
PROGRESSIVE OFF
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
SETUP
or
ENTER
Hint
ENTER
DISPLAY menu
STILL MODE:
(Default: AUTO)
See Hint to the right.
DISPLAY
TV ASPECT
STILL MODE
PROGRESSIVE
(for TV ASPECT
& STILL MODE)
TV ASPECT
or
SETUP
6 To exit the menu
Select the
desired
setting.
4:3 LETTER BOX
AUTO
OFF
Select the
desired
setting.
STILL MODE
TV ASPECT
4:3 LETTERBOX
AUTO
STILL MODE
PROGRESSIVE OFF
AUTO
FIELD
FRAME
or
ENTER
ENTER
5
If you do not hit any buttons for 15 seconds,
Progressive Scan will switch to “OFF”.
PROGRESSIVE: QUICK
(Default: OFF)
See Hint to the right.
TV ASPECT
4:3 LETTERBOX
AUTO
STILL MODE
PROGRESSIVE OFF
Select
YES.
SETUP
4:3 LETTERBOX
AUTO
ON
Confirm again to use progressive scan.
If Picture is good, Select “YES”.
NO
YES
SELECT: K / L
or
SET:ENTER
ENTER
If “PROGRESSIVE” is “ON”,
this message appears:
6 To confirm the
PROGRESSIVE
scanning mode
ENTER
C
Select
YES.
Before proceeding…
1. Make sure your TV has progressive scan.
2. Connect with component video cable
NOTE: If there is no picture or picture is
distorted after selecting “YES”,
wait about 15 seconds for auto recovery.
A c ti va te P r o gr e s s i ve ?
SELECT: K / L
NO
YES
ENTER
or
SET:ENTER
TV ASPECT:
• Select “4:3 LETTER BOX”,
so that black bars may
appear on the top and bottom of the screen.
• Select “4:3 PAN & SCAN”
for a full height picture with
both sides adjusted.
• Select “16:9 WIDE” if a
wide-screen TV is connected to this unit.
STILL MODE:
• Select “AUTO” usually.
• If you select AUTO, automatically select the best resolution
setting (FRAME or FIELD)
based on the datacharacteristics of the pictures. (default).
• If you select “FIELD”, the
picture in the still mode will
be stabilized.
• If you select “FRAME”, the
picture in the still mode will
be highly defined.
• An individual picture on TV
screen is called as “frame”,
which consists of two separate images called as “field”.
Some pictures may be blurred
at the AUTO setting instill mode
due to their data characteristics.
PROGRESSIVE:
• You can set “PROGRESSIVE”
to “OFF” either in the Display
menu or by pressing and holding [PLAY B] on the front of the
unit for more than 5 seconds.
• When “PROGRESSIVE” is “ON”,
video signals from VIDEO OUT
and S-VIDEO OUT jacks will be
distorted or not be output at all.
AUDIO Setting
Choose the appropriate audio settings for your equipments. It only affects during the playback of DVD discs. Follow steps 1)
to 3) in the “CUSTOM Menu” section on page 14.
4
Select the desired item.
5
6 To exit the menu
SETUP
DRC (Dynamic Range Control): (Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
or
DRC
ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM ENTER
AUDIO menu
SETUP
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
BITSTREAM
OFF
ON
BITSTREAM
DOWN SAMPLING: (Default: ON)
Set to “ON” when outputting in 48 kHz.
Set to “OFF” when outputting the original sound.
DRC
ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ENTER
ON
OFF
BITSTREAM
DOLBY DIGITAL: QUICK (Default: BITSTREAM)
Set to “BITSTREAM” when the unit is connected to a Dolby Digital receiver.
• BITSTREAM: Outputs a Dolby Digital Signals.
• PCM: Convert the Dolby Digital into PCM (2 channel).
DRC
ON
DOWN SAMPLING ON
DOLBY DIGITAL
BITSTREAM
ON
ON
PCM
Hint
DRC:
• This function is available
only on the discs which
are recorded in the Dolby
Digital format.
DOWN SAMPLING:
• When playing disc with
copyright protection, the
sound will be down sampled at 48kHz, even if
you set to OFF.
• This function is available
only on digital outputting
of a disc recorded in
96kHz.
ENTER
– 15 –
EN
Functions
4
E6150UD_ENSP.qx33
D
05.4.5 14:24
Page 16
PARENTAL Setting
Parental Control limits the disc viewing that exceed your settings. (An incorrect password will not play.)
This feature prevents your children from viewing inappropriate materials.
Parental Le vels
Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set.
Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
4
5
Enter your desired fourdigit password (except
for 4737).
6
Select “PARENTAL
LEVEL”.
7
Select the
desired level.
To exit
the menu
SETUP
1
2
3
4
5
6
7
8
9
or
ENTER
PARENTAL LEVEL
PASSWORD CHANGE
0
or
ENTER
PARENTAL LEVEL
ALL
8
7 [NC-17]
6 [R]
ALL
PARENTAL menu
SETUP
PARENTAL
CONTROL LEVELS
• ALL:
All parental locks are cancelled.
• Level 8:
DVD softwares of any grades (adult/general/children) can be played back.
• Levels 7 to 2: Only DVD softwares intended for general use and children can be played
back.
• Level 1:
Only DVD softwares intended for children can be played back, with those
intended for adult and general use prohibited.
TIPS FOR LEVELS
• 7 [NC-17]:
No one under 17 admitted
• 6 [R]:
Restricted; under 17 requires accompanying parent or adult guardian
• 4 [PG13]:
Unsuitable for children under 13
• 3 [PG]:
Parental Guidance suggested
• 1 [G]:
General Audience
PASSWORD
Please enter a 4-digit password.
or
If you have set a password already,
enter the current four-digit
password.
SETUP
ENTER
PARENTAL
PASSWORD
Enter current password.
Hint
• DVD-Video discs may not respond to the parental lock settings. Make sure this function
works with your DVD-Video discs.
Functions
To Chang e the Pass w ord for Parental Controls
You can change your password for parental controls. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
4
5
Enter your desired fourdigit password (except
for 4737).
1
2
3
4
5
6
7
8
9
6
Select “PASSWORD
CHANGE”.
or
ENTER
PARENTAL LEVEL
PASSWORD CHANGE
7
Enter your new
four-digit password
(except for 4737).
ALL
1
2
3
4
5
6
7
8
9
SETUP
ENTER
0
0
PARENTAL menu
SETUP
Hint
• Record the password in
case you forget it.
• If you forget the password, hit [4], [7], [3], [7]
at step 4), then enter your
new password.
• Password will be cleared
and parental levels will be
set to “ALL”.
PARENTAL
PASSWORD
SETUP
PARENTAL
Please enter a 4-digit password.
PASSWORD
Enter current password.
E
To exit
the menu
OTHERS Setting
You can change the other functions. Follow steps 1) to 3) in the “CUSTOM Menu” section on page 14.
4
Select the desired item
5
6 To exit the menu
ANGLE ICON:
(Default: ON)
Set to “ON” to show the angle icon when multiple camera
angles are available during DVD playback.
or
OFF
ON
ANGLE ICON
ON
AUTO POWER OFF ON
OTHERS menu
SETUP
OTHERS
ANGLE ICON
AUTO POWER OFF
ON
ON
SETUP
ENTER
AUTO POWER OFF:
(Default: ON)
Set to “ON” to turn this unit off automatically after
30 minutes of no use.
ANGLE ICON
ON
AUTO POWER OFF ON
ON
OFF
ENTER
– 16 –
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 17
Reset to the Default Setting (except for PARENTAL Setting)
2
1
STOP
4
3
SETUP
or
or
To exit
the menu
SETUP
<SETUP MENU>
SETUP
QUICK
CUSTOM
INITIALIZE
Select “INITIALIZE”.
ENTER
Select “YES”.
SETUP
SETUP
Initialize?
NO
YES
QUICK
CUSTOM
INITIALIZE
ENTER
Hint
INITIALIZE
Hit
twice.
• When you cancel
to initialize at step
3), select “NO”.
Information
Troubleshooting Guide
Problem
Solution
No power
–Check if the AC power cord is properly connected.
–Unplug the outlet once, and wait for 5-10seconds and then plug it in again
–Check if the TV is switched on.
–Check the video connection
–Check the VIDEO/AUDIO cable connections to the TV
(See Connection to a TV)
–Set PROGRESSIVE correctly. Turn it on only if your TV has
Progressive Scan and you are using the Component Video connections between the unit and the TV. Disable Progressive Scan for all
other connections. (See page 6)
–Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
–Connect the unit directly to the TV.
–Connect the unit directly to the TV.
–Make sure the disc is compatible with the unit.
–Check if the INTERLACE/PROGRESSIVE mode is set correctly. See page 6.
–Adjust the volume.
–Check that the speakers are connected correctly.
–Check the digital connections.
–Check if the audio format of the selected audio language matches
your receiver capabilities.
–This unit does not support DTS audio.
This is not a malfunction.
–Check the disc for fingerprints/scratches and
clean with a soft cloth wiping from center to edge.
–Clean the disc
–Clean the disc
–Ensure the disc label is facing up.
–Check if the disc is defective by trying another disc.
–Cancel the parental lock or change the control level.
–Insert a correct disc that plays on this unit.
–Handle a disc with special care so that it does not have fingerprints,
scratches, or dusts on its surface.
–Reset the unit by switching the unit off, then on again.
–Aim the remote control directly at the sensor on the front of the unit.
–Reduce the distance to the unit.
–Replace the batteries in the remote control.
–Re-insert the batteries with their polarities (+/– signs) as indicated.
–Tune your radio to an empty AM station so that you hear a lot of
noises. Then, turn the volume up. If you hear some signal sound
from the radio by pressing buttons on the remote control, the
remote control is working.
–To completely reset the unit, unplug the AC
cord from the AC outlet for 5-10 seconds.
–Operations may not be permitted by the disc.
Refer to the instructions of the disc.
–Use a commonly available cleaning CD/DVD to
clean the lens before sending the unit for repair.
–The angle cannot be switched for DVDs which do not contain
multiple angles. In some cases multiple angles are only recorded
for specific scenes.
–Check the “PARENTAL” setting.
–Enter the default password “4737”, then your forgotten password
will be cleared
No sound or picture
Distorted picture
Completely distorted picture or
black/white picture with DVD
No sound or distorted sound
No audio at digital output
No DTS audio is output
Picture freezes momentarily
during playback
Disc can’t be played
No return to start-up screen when disc is removed
The unit does not respond to
the remote control
Buttons do not work or the unit stops
responding
The unit does not respond to some
operating commands during playback
The unit cannot read
CDs/DVDs
Angle does not switch
Playback does not start when the title is selected
The password for rating level has been forgotten
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual
for more details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
EN
– 17 –
Information
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit consulting the following checklist.
E6150UD_ENSP.qx33
05.4.5 14:24
Page 18
Specifications
Output signal format:
NTSC color
Power source:
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption:
10 W (standby: 0.8 W)
Operating temperature:
41°F (5°C) to 104°F (40°C)
Dimensions:
W : 9 5/8"
(245 mm)
H : 2"
(52 mm)
D : 9 13/16" (249 mm)
Weight :
Approx 2 lbs (0.9 kg)
• Designs and specifications are subject
to change without notice.
• If there is a discrepancy between languages, the default language will be
English.
Language List
Language
Code
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
Language
Code
Language
Code
Language
Code
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
6565
6557
6558
6561
5165
6567
6569
6568
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language
setting on page 13. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)
Information
Limited Warranty
FUNAI CORP. will repair this MAGNAVOX product, free of charge in
the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective
parts without charge for one (1) year from the date of
original retail purchase. Certain parts are excluded
from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for
a period of ninety (90) days from the date of original
retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required
together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the
product are altered, replaced, defaced, missing or if service was
attempted by an unauthorized service center. This MAGNAVOX
Limited warranty does not apply to any product not purchased and
used in the United States.
This product is produced for home use and this warranty only covers
failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment,
or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident,
misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or
office use of this product or damage which results from fire, flood,
lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC
PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL
IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR
CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES
INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST
BE PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO
FUNAI AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU
ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF
THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN
OF THIS PRODUCT WITHOUT PRIOR NOTICE.
To locate your nearest MAGNAVOX Authorized Service Center or
for general service procedure, please call or write to the following:
FUNAI CORPORATION, INC.
SERVICE CENTER
19900 Van Ness Avenue, Torrance, CA 90501
Tel :1-800-605-8610
http://www.funai-corp.com
Head Office: 100 North Street, Teterboro, NJ 07608
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
– 18 –
EN
E6150UD_ENSP.qx33
05.4.5 14:24
Page 19
Español
1
4
Conexiones
Si su televisor tiene entradas
de AUDIO/VIDEO vea la sección “Connection to a TV” en la
página 6 en el Manual de
Manejo. En caso contrario, vea
la sección “Connecting to RF
Modulator” en la página del
frente en el Manual de Manejo.
Reproducción
Antes.
¡Encienda el televisor, amplificador y
otros equipos conectados a esta
unidad. Asegúrese que el televisor y el
sintonizador de audio (de venta en los
comercios) están en el canal correcto.
STANDBY–ON
1
OPEN/CLOSE
DISPLAY
SEARCH
MODE
1
2
3
4
5
6
7
8
1
AUDIO
SUBTITLE
DVD-V
1
3
CD
OPEN/CLOSE
STANDBY–ON
Para empezar la
reproducción
2
4
Ponga un
disco con
la etiqueta
hacia
arriba.
Para parar la
reproducción
ANGLE
REPEAT
CLEAR
A-B
PAUSE
9
0
Instalación de las pilas
en el control remoto
SLOW
PLAY
REV
FWD
Control remoto
Disco
Botón
(Orden alfabético)
3
1
1
2
3
4
5
6
7
8
9
0
+10
Para cambiar el idioma
en la pantalla
ENTER
Confirme que ha seleccionado “QUICK”.
✄
• Para seleccionar idiomas de
audio en un disco.
• Para borrar los marcadores.
• Para borrar los números mal
entrados.
• Para borrar el punto para la
repetición A-B.
DISPLAY
• Para mostrar el modo de
disco actual.
ENTER
REV
FWD
MENU
• Para activar/desactivar el
nivel del negro.
• Para activar/desactivar el
ambiental virtual.
QUICK
PLAYER MENU
TV ASPECT
PROGRESSIVE
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
BITSTREAM
OPEN/CLOSE
Seleccione el idioma deseado para
las indicaciones en la pantalla.
or
PLAYER MENU
ENGLISH
FRANCAIS
ESPAÑOL
STANDBY–ON
REPEAT
RETURN
ENTER
Para salir del menú.
• Para empezar la
reproducción del disco.
• Para empezar la
reproducción del disco.
• Para encender o apagar la
unidad.
• Para encender o apagar la
unidad.
• Para reproducir
repetidamente un capítulo o
título.
• Para reproducir repetidamente
una canción o disco.
• Para volver a la operación
anterior en el menú.
• Para volver a la operación
anterior en el menú.
• Para buscar un capítulo, título • Para buscar una canción.
o tiempo.
• Para buscar el tiempo.
• Para colocar o buscar los
• Para colocar o buscar los
marcadores.
marcadores.
SEARCH
MODE
4
• Para disponer el orden de reproducción
o la reproducción aleatoria.
• Para activar/desactivar el
ambiental virtual.
• Para hacer una pausa en la reproducción. • Para hacer una pausa en la
• Para avanzar la reproducción un cuadro
reproducción del disco.
cada vez.
PLAY
3
• Para buscar en avance/
retroceso por un disco.
• Para abrir o cerrar la bandeja • Para abrir o cerrar la bandeja
del disco.
del disco.
PAUSE
ENTER
• Para buscar en avance/
retroceso por un disco.
• Para empezar la reproducción
en avance lento/retroceso
durante el modo de pausa.
• Para seleccionar ESTÉREO
L-ch o R-ch.
• Para borrar los marcadores.
• Para eliminar el Nº de estado
en la entrada de programa.
• Para borrar los números mal
entrados.
• Para borrar el punto para la
repetición A-B.
• Para mostrar el modo de
disco actual.
• Para llamar el Menú en un
disco.
MODE
SETUP
• Para mover el cursor y
determinar la posición.
AUDIO
CLEAR
Confirme que ha seleccionado “PLAYER MENU”.
• Para mover el cursor y
determinar la posición.
• Para seleccionar los ángulos
de cámara en un disco.
SETUP
2
CD
• Para seleccionar
directamente la canción.
ANGLE
SETUP
QUICK
CUSTOM
INITIALIZE
DVD-V
• Para seleccionar
directamente el capítulo o
título.
• Para repetir entre su punto A • Para repetir entre su punto A y B
y B seleccionado.
seleccionado.
A-B
STANDBY–ON
STOP
4
STOP
5
3
2
1
3
STOP
SETUP
SETUP
• Para llamar el menú de
ajustes de DVD.
• Para llamar el menú de
ajustes de DVD.
• Para saltar capítulos.
• Para saltar canciones.
• Para parar la reproducción.
SKIP
STOP
• Para parar la reproducción.
SUBTITLE
• Para seleccionar subtítulos
en un disco.
TOP MENU
• Para llamar el menú inicial
en un disco.
ZOOM
• Para ampliar la imagen de
vídeo en DVD. (x2/x4)
– 19 –
ES
Español
2
PLAY
+10
SKIP
E6150UD_ENSP.qx33
05.4.5 14:38
Page 20
Quick Use Guide
4
Connections
If your TV has AUDIO/VIDEO
input jacks, see the section
“Connection to a TV” on page
6 of the Owner’s Manual. If not,
see the section “Connecting to
RF Modulator” on the front
page of the Owner’s Manual.
Playback
Before:
¡Turn on the TV, amplifier and any other equipments which are connected to this unit. Make
sure the TV and audio receiver (commercially
available) are set to the correct channel.
STANDBY–ON
1
OPEN/CLOSE
DISPLAY
SEARCH
MODE
1
2
3
4
5
6
7
8
9
REPEAT
CLEAR
A-B
PAUSE
0
Installing the Batteries
for the Remote Control
3
Disc
2
3
4
5
6
7
8
9
0
+10
ENTER
A-B
Confirm that “QUICK” is
selected.
ENTER
REV
FWD
MENU
MODE
OPEN/CLOSE
Select the desired language
for the On-Screen Display.
or
PLAYER MENU
ENGLISH
FRANCAIS
ESPAÑOL
• To repeat between your
chosen point A and B.
• To display the current disc
mode.
• To display the current disc
mode.
• To search forward/backward
through a disc.
• To begin slow forward
/reverse playback during
the pause mode.
• To search forward/backward
through a disc.
• To call up the Menu
on a disc.
• To arrange the playing
• To set black level on/off.
order or play randomly.
• To set virtual surround on/off.
• To set virtual surround on/off.
• To begin disc playback.
• To begin disc playback.
• To turn the unit on or off.
• To turn the unit on or off.
REPEAT
• To play a chapter or title
repeatedly.
• To play a track or disc
repeatedly.
RETURN
• To return to the previous
operation in menu.
• To return to the previous
operation in menu.
STANDBY–ON
SETUP
SETUP
SKIP
STOP
SUBTITLE
TOP MENU
ZOOM
Printed in China
• To repeat between your
chosen point A and B.
• To pause disc playback.
SEARCH
MODE
To exit the menu.
• To move the cursor and
determine its position.
• To pause disc playback.
• To advance playback
one frame at a time.
ENTER
4
• To move the cursor and
determine its position.
• To open or close the disc
tray.
PLAY
3
• To select track directly.
• To open or close the disc
tray.
PAUSE
ENTER
• To select chapter or title
directly.
• To select audio languages on • To select STEREO,
a disc.
L-ch or R-ch.
• To clear the markers.
• To clear the markers.
• To remove status number
in program input.
• To clear the numbers
• To clear the numbers
entered incorrectly.
entered incorrectly.
• To cancel the point for A-B
• To cancel the point for A-B
repeat.
repeat.
DISPLAY
ENGLISH
4:3 LETTER BOX
OFF
BITSTREAM
CD
• To select camera angles on
a disc.
SETUP
PLAYER MENU
TV ASPECT
PROGRESSIVE
DOLBY DIGITAL
DVD-V
AUDIO
CLEAR
QUICK
4
ANGLE
SETUP
SETUP
STOP
PLAY
+10
FWD
STANDBY–ON
Confirm that “PLAYER MENU” is selected.
To stop playback
PLAY
1
QUICK
CUSTOM
INITIALIZE
2
4
Remote Control
To Change the OnScreen Language
STOP
To start playback
SLOW
(Alphabetical order)
1
Insert a
disc with
label
facing up.
OPEN/CLOSE
SKIP
REV
Button
3
2
3
STOP
5
3
2
1
1
AUDIO
ANGLE
1
CD
STANDBY–ON
SUBTITLE
2
DVD-V
• To search track.
• To search chapter, title or time. • To search time.
• To set or search the
• To set or search the
markers.
markers.
• To call up the DVD setup
menu.
• To call up the DVD setup
menu.
• To skip chapters.
• To skip tracks.
• To stop playback.
• To stop playback.
• To select subtitles on a disc.
• To call up the Top Menu
on a disc.
• To magnify part of a picture.
(x2/x4)
1VMN20430 / E6150UD ★★★★★
✄
1