Owner`s manual | FUNAI V7PFDVD20 TV DVD Combo User Manual

INTRODUCTION
Owner’s Manual
INITIAL SETTING
V7PFDVD20
CONNECTION
20” Digital / Analog Television
built-in DVD Player
WATCHING TV
OPTIONAL SETTING
OPERATING DVD
DVD SETTING
OPEN/CLOSE
VIDEO
VOLUME
CH.
STOP
SELECT
L - AUDIO - R
HEADPHONE
TROUBLESHOOTING
POWER
PLAY
INFORMATION
TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.
INTRODUCTION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
The important note is located on the rear of the cabinet.
Important Safeguards
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss
of an authorization code for a CATV converter, is not intended to
be unplugged by the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in the cleaning
description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by
the TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on an unstable cart, stand, tripod, bracket, or table. The
TV may fall, causing serious injury to someone,
and serious damage to the appliance. Use
only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold
with the TV.
Any mounting of the appliance should follow
the manufacturer’s instructions and should
use a mounting accessory recommended by the manufacturer. An
appliance and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé
que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez
sur un meuble à roulettes, déplacez les deux
ensembles avec précaution. Un arrêt brusque,
l’utilisation d’une force excessive et des
surfaces irrégulières risquent de déstabiliser l’
ensemble et de le renverser.
9. VENTILATION - Slots and openings in the cabinet and the back or
bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings
must not be blocked or covered. The openings should never be
blocked by placing the TV on a bed, sofa, rug, or other similar
surface. This TV should never be placed near or over a radiator or
heat register. This TV should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your appliance
dealer or local power company. For TVs intended to operate from
battery power, or other sources, refer to the operating instructions.
2
EN
11. GROUNDING OR POLARIZATION - This TV is equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still
fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they
exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the TV, be sure the antenna or cable
system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National
Electrical Code, ANSI/NFPA No. 70, provides information with
respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the
grounding electrode. (Fig. A)
FIGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SEC TION 810-20)
ELEC TRIC
SERVICE
EQUIPMENT
GROUNDING CONDUC TORS
(NEC SEC TION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELEC TRICAL CODE
POWER SERVICE GROUNDING
ELEC TRODE SYSTEM
(NEC ART 250, PART H)
14. LIGHTNING - For added protection for this TV receiver during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage to the TV due
to lightning and power-line surges.
15. POWER LINES - An outside antenna system should not be located
in the vicinity of overhead power lines or other electric light of
power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
16. OVERLOADING - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are expressly approved in the manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to
possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates
copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
INFORMATION
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.
TROUBLESHOOTING
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building as close to the point of cable entry as practical.
DVD SETTING
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
OPERATING DVD
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
OPTIONAL SETTING
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
WATCHING TV
CAUTION:
ATTENTION:
INITIAL SETTING
5 Precautions
CONNECTION
e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in performance, this
indicates a need for service.
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts specified by
the manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock,
injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
TV, ask the service technician to perform routine safety checks to
determine that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
INTRODUCTION
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
this TV through openings as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the TV.
c. If the TV has been exposed to rain or water.
d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the TV to its normal operation.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
3
EN
INTRODUCTION
LOCATION
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the
unit. Do not place the unit on a carpet because this will block the ventilation holes.
• Install the unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the unit near strong magnetic fields.
• Avoid moving the unit to locations where temperature differences are extreme.
• Be sure to unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug the power cord immediately and take the unit to our authorized service center for servicing.
• Do not put your fingers or objects into the unit or disc tray.
• Do not place anything directly on top of the unit.
MOISTURE WARNING
• Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold
room or under conditions of high humidity.
When the condensation occurs inside the unit, turn the unit on and leave it at least 2 hours to dry out.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You
should record the number and other vital information here and retain this book as a permanent record of your purchase to aid
identification in case of theft.
date of purchase
dealer phone No.
serial No.
dealer purchase from
model No.
dealer address
Note about recycling:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with
your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
5 Supplied Accessories
owner’s manual
(1EMN22501)
remote control
(NF107UD)
batteries
(AA x 2)
• If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free customer support line found on the cover of this manual.
• Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
Contact your local electronics store for these items.
5 Symbols Used in this Manual
The following is the description for the symbols used in this manual.
Description refers to:
TV FUNCTIONS
: Analog TV operation
DVD
DTV
: Digital TV operation
CD
• If neither symbol appears under the function
heading, operation is applicable to both.
4
EN
DVD FUNCTIONS
TV
: Playback of DVD-video
: Playback of audio CD
• If neither symbol appears under the function
heading, operation is applicable to both.
INTRODUCTION
5 Contents
DVD Functions
INTRODUCTION
Basic Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
INITIAL SETTING
WATCHING TV
OPTIONAL SETTING
TROUBLESHOOTING
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
INFORMATION
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Electrical Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back cover
DVD SETTING
Channel Add/Delete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DTV Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
DTVCC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DVD Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Display Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DVD Audio Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Parental Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Reset to the Default Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
OPERATING DVD
Channel Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Volume Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switching Each Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TV Screen Display Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DVD SETTING
OPTIONAL SETTING
Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
WATCHING TV
TV Functions
Playable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Unplayable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Resume Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Step-by-step Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Fast Forward / Fast Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Search Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Repeat A-B Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Random Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
On-screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Special Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
INITIAL SETTING
CONNECTION
OPERATING DVD
CONNECTION
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TROUBLESHOOTING
INFORMATION
5
EN
INTRODUCTION
5 Features
TV
• DTV/TV/CATV
- You can use your remote control to select
channels which are broadcast in digital format and
conventional analog format. Also, cable subscribers
can access their cable TV channels.
• Program Information Display (DTV only)
- You can display the title, contents and other
information of the current DTV program on the TV
screen.
• Auto Channel Scan
- This unit automatically scans and memorizes
channels available in your area, eliminating difficult
setup procedures.
• V-chip
- This feature allows you to block children’s access to
inappropriate TV programs.
• Closed Caption Decoder
- Built-in closed caption decoder displays text for
closed caption supported programming.
• Auto Shut Off Function
- If there is no signal input from the antenna terminal
and no operation for 15 minutes, the unit will turn
itself off automatically.
• Sleep Timer
- This feature will automatically turned off the power
of the unit at a specific time.
• Choices for On-screen Language
- Select your on-screen language:
English, Spanish or French.
• PLL Frequency Synthesized Tuning
- Provides free and easy channel selection and lets
you tune directly to any channel using the channel
number buttons on the remote control.
• AV Input
• Digital Audio Coaxial Output
DVD
• Dolby Digital Sound
- Enjoy Dolby Digital multi-channel surround sound
when you connect the unit to your Dolby Digital
decoder.
• Still / Fast / Slow / Step Playback
- Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
• DVD Menus in a Desired Language
- You can display DVD menus in a desired language, if
available on a DVD-video.
• Screen Saver
- If there is no operation for 5 minutes, the screen
saver program starts. The unit will turn itself off automatically.
• Parental Lock
- Block the viewing of DVD-video unsuitable for children.
• Resume Playback
- Lets you resume playback from the point at which
playback was stopped.
• Bit Rate Indication
• DRC (dynamic range control)
- You can control the range of sound volume.
¨ Accessing from [MODE] button
During playback...
• Choices for Audio Language and Stereo Sound
function
- Select your desired language or stereo sound function
when different options are available on your disc.
• Subtitles in a Desired Language
- You can select a desired language for displaying subtitle, if that language is available on a DVD-video.
• Selecting a Camera Angle
- You can select the desired camera angle, if a DVD
contains sequences recorded from different angles.
• Zoom
- Allows you to enlarge the size of picture image.
• Black Level Adjustment
• Virtual Surround
• Search
- chapter / title / track / time
• Marker
- The part on the disc designated by user can be
called back.
• Repeat
- chapter / title / track / all / A-B
In stop mode...
• Program Playback for audio CD
- You can program the order of tracks to play them
back in designated order.
• Random Playback for audio CD
- This unit can shuffle the order of tracks to play them
back in randomly.
6
EN
INTRODUCTION
5 Remote Control Function
4.
14
3
4
5
21
9
22
10
11
23
15.
16.
17.
18.
19.
20.
21.
22.
23.
TROUBLESHOOTING
5 Installing the Batteries
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
2
3
INFORMATION
1
DVD SETTING
POWERy
y button (p11)
Press to turn the unit on and off.
PICTURE/SLEEP button (p15 / p16)
• Press to adjust the picture quality.
• Press to activate the sleep timer.
Number buttons (p13)
Press to select channels.
+10/+100 button
• Press to select 100 or higher
channels. (CATV)
• Press to search if there are minor
channels on the currently selected
major channel. (DTV)
14.
OPERATING DVD
3.
8
OPTIONAL SETTING
2.
16
17
18
19
20
13.
WATCHING TV
1.
6
7
12.
INITIAL SETTING
15
11.
• Press to select the audio language
(DVD), or sound mode (CD).
• Press to magnify the part of picture
(approx. 1.3x, 2x and 4x : DVD).
• Press to select the subtitles on a disc
(DVD).
ENTER button (p12)
Press to confirm your selection.
OPEN/CLOSE A button (p23)
Press to open or close the disc tray.
SELECT button (p14)
• Press to access a connected external
device like a video game, camcorder
or VCR.
• Press to select the digital, analog,
external input or DVD mode.
CH. K / L buttons (p13)
Press to select channels.
VOL. X / Y buttons (p13)
Press to adjust the volume.
MUTE button (p13)
Press to turn the sound on and off.
SET-UP button (p11)
Press to display the main menu.
STOP C button (p23)
Press to stop the disc playback.
FWD D button (p24)
Press to begin the slow forward
playback during the pause mode
(DVD) and the search forward
through a disc.
TITLE button (p23)
Press to call up the title menu on a
DVD.
DISC MENU button (p23)
Press to call up the disc menu on a
DVD.
s / B / K / L buttons (p12)
Press to move left/ right/ up/ down
through the items.
button (p26)
RETURN
Press to return to the previous menu
operation.
CONNECTION
12
13
1
2
DISPLAY button (p14)
Digital Mode (DTV)
• Press to display the channel number
and the program information.
Analog Mode (TV)
• Press to display the channel number.
External Input Mode
• Press to display the currently
selected external input mode.
DVD mode
• Press to display the current status
(DVD, CD).
5. SKIP H / G button (p25)
Press to skip forward or backward
chapters, titles (DVD) or tracks (CD).
6. PLAY B button (p23)
Press to begin disc playback.
7. REV E button (p24)
Press to begin the slow reverse
playback during the pause mode
(DVD) and the search backward
through a disc.
8. PAUSE F button (p23)
Press to pause the disc playback.
9. CLEAR button (p26)
• Press to clear the numbers entered
incorrectly.
• Press to cancel the point A for A-B
repeat (DVD, CD).
• Press to remove the track number in
program input (CD).
10. MODE button (p6)
• Press to arrange the playing order or
play back randomly (CD).
• Press to set the black level (DVD)
and virtual surround (DVD, CD) on or
off.
• Press to change the camera angle to
see the sequence being played back
from different angle (DVD).
• Press to search chapter, title (DVD),
time (DVD, CD) or track (CD).
• Press to set the marker (DVD, CD).
• Press to repeat playback chapter,
title (DVD), or track, disc (CD)
repeatedly or between designated
point A and B (DVD, CD).
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
7
EN
INTRODUCTION
5 Control Panel
1.
POWER
OPEN/CLOSE
VIDEO
VOLUME
CH.
STOP
SELECT
L - AUDIO - R
HEADPHONE
PLAY
POWER
OPEN/CLOSE
VIDEO
VOLUME
CH.
STOP
SELECT
L - AUDIO - R
HEADPHONE
PLAY
1
2
3
4
5
6
7
8
9
10
11
HEADPHONE jack
Headphone connection for personal listening.
2. AUDIO input jacks (p10)
RCA audio cable connection for an external device.
3. VIDEO input jack (p10)
RCA video cable connection for an external device.
4. OPEN/CLOSE A button (p23)
Press to open or close the disc tray.
5. Disc Tray (p23)
Place the disc with label facing up.
6. Infrared Sensor Window
Receives infrared rays transmitted from the remote
control.
7. PLAY B button (p23)
Press to begin disc playback.
8. STOP C button (p23)
Press to stop disc playback.
9. CH. SELECT K button (p13)
Press to select higher channels than currently viewing
channel and external input mode.
10. VOLUME X / Y buttons (p13)
Press to adjust the volume.
11. POWER button (p11)
Press to turn the unit on and off.
5 Rear Panel
1.
2.
3.
ANT.
COAXIAL
1
ANT.
COAXIAL
2
3
8
EN
AC Power Cord
Connect to a standard AC outlet to supply power to
this unit.
ANT. input jack (p9)
RF coaxial cable connection for your antenna or
cable/satellite box.
COAXIAL (digital audio) output jack (p10)
Digital audio coaxial cable connection for a decoder
or an audio receiver.
INTRODUCTION
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
CONNECTION
5 Basic Connection
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
INITIAL SETTING
[Antenna Cable Connection]
When connecting the unit to an antenna or cable TV company (without cable/satellite box)
Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
WATCHING TV
e.g.)
rear of this unit
VHF / UHF
antenna
OPTIONAL SETTING
RF coaxial cable
ANT.
or
cable TV
company
ANT.
COAXIAL
OPERATING DVD
*Once connections are completed, turn on the unit and begin initial setup.
Channel scanning is necessary for the unit to memorize all available channels in your area.
(Refer to “Initial Setup” on page 11.)
Note:
DVD SETTING
• For your safety and to avoid damage to device, please unplug the RF coaxial cable from the antenna input jack before moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than
settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CATV installer.
Connect the RF coaxial cable on your home outlet to the input jack of the cable/satellite box.
Use another RF coaxial cable to connect the antenna input jack of the unit to the output jack of the cable/satellite box.
e.g.)
rear of this unit
satellite
dish
INFORMATION
cable/satellite box
ANT. IN RF OUT
or
cable TV
company
ANT.
RF coaxial cable
RF coaxial cable
TROUBLESHOOTING
[Connection to Cable Box or Satellite Box]
ANT.
COAXIAL
*Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
9
EN
CONNECTION
Cables not included.
Please purchase the necessary cables at your local store.
5 External Device Connection
[Video Cable Connection]
When you connect this unit to an external device, use the audio/video input jacks on the front of this unit.
Make the connection as illustrated below.
When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
front of this unit
e.g.)
AUDIO OUT
R
L
camcorder
VIDEO
VIDEO
OUT
L - AUDIO - R
HEADPHONE
video game
RCA video cable
VCR
RCA audio cable
[Digital Audio Output Connection]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital broadcasting sound.
rear of this unit
e.g.)
ANT.
DIGITAL AUDIO
COAXIAL IN
COAXIAL
ANT.
COAXIAL
Dolby Digital decoder
10
EN
digital audio coaxial cable
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
INTRODUCTION
INITIAL SETTING
TV Functions
Note:
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and “AUTO PRESET CH”, which
automatically scans and memorizes viewable channels.
Make sure if the unit is connected to antenna or cable.
1 After making all the necessary connections, press
[POWERy] to turn on the unit.
2 Use [VOL. X/Y] or [CH. K] to select the on-screen
language from the choices on the left side of the TV
screen. (ENGLISH / ESPAÑOL / FRANÇAIS)
WATCHING TV
• This operation may take a few moments.
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWERy] or [SET-UP] during “AUTO PRESET
CH”, this setting will be canceled.
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select “CHANNEL SETUP” in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 12.)
• You can cancel or exit the initial “AUTO PRESET CH” menu by
pressing [SET-UP].
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• If there is no signal input from the antenna terminal and no
operation for more than several seconds after you turn on
the unit, “HELPFUL HINTS” appears. Follow the instructions
listed on the TV screen.
INITIAL SETTING
Before you begin:
OPTIONAL SETTING
--- HELPFUL HINTS --1 . P L E A S E C H E C K TO S E E I F
THE ANTENNA/CABLE/
S AT E L L I T E I S P R O P E R LY
C O N N E C T E D.
2 . D I D YO U P E R F O R M
” AU T O P R E S E T C H ” ?
3 . P L E A S E R E F E R TO F RO N T
PA G E O F T H E O W N E R ’ S
M A N U A L O R R E A R PA N E L
FOR SUPPORT LINE
I N F O R M AT I O N .
--- LANGUAGE/IDIOMA/LANGUE ---
or
CONNECTION
5 Initial Setup
VOLY
ENGLISH
PRESS
ESPAÑOL
PRESIONE VOLX
FRANÇAIS
PRESSEZ CH. K
5 Main Menu
3 Use [VOL. X/Y] to select “AUTO PRESET CH(TV/DTV)”
- INITIAL SETUP -
• Scanning and memorizing the channels automatically
start.
25
• When the scanning and memorizing are completed,
the lowest memorized channel in the broadcasting
will be displayed.
--- TV SETUP --CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
• CHANNEL SETUP
You can automatically scan the viewable channels and
remove those that are undesired.
(Refer to “Auto Channel Scan” on page 12.)
• V-CHIP SETUP
You can set the viewing limitations.
(Refer to “V-chip” on page 19.)
• LANGUAGE
You can change the language (English, Spanish or
French) displayed on the main menu.
(Refer to “Language Selection” on page 12.)
• CAPTION
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to “Closed Caption” on page 17.)
• DTV SETUP
You can set the screen display or caption in the DTV
mode. (Refer to “DTV Closed Caption” on page 18.)
INFORMATION
AUTO PRESET CH(TV/DTV)
e.g.) digital TV mode
TROUBLESHOOTING
1. PLEASE CONNECT ANTENNA
OR CABLE OR SATELLITE
TO THIS UNIT.
2. SET UP THE ITEMS WITH
VOL / , AND CH BUTTONS.
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
Press [SET-UP].
DVD SETTING
for TV channels or “AUTO PRESET CH(CATV)“ for CATV
channels, then press [CH. K].
OPERATING DVD
This section describes the overview of the main menu displayed when you
press [SET-UP].
For more details, see the reference page for each item.
The main menu consists of the function setting items below.
• Press [VOL. Y] for English.
• Press [VOL. X] for Spanish.
• Press [CH. K] for French.
11
EN
INITIAL SETTING
5 Auto Channel Scan
Note:
If you switch wires (e.g., between antenna and CATV) or if you move the
unit to a different area after the initial setting, or if you recover the DTV
channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
1 Press [SET-UP] to display the main menu.
2
Use [Cursor K/L] to select “CHANNEL SETUP”,
then press [ENTER].
e.g.) digital TV mode
5 Language Selection
--- TV SETUP ---
or
3
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
You can choose English, Spanish, or French as your on-screen language.
1 Press [SET-UP] to display the main menu.
Use [Cursor K/L] to select your desired preset
type, then press [ENTER].
e.g.) digital TV mode
or
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWERy] or [SET-UP] during
“AUTO PRESET CH”, the setting will be canceled.
• When no channel can be received by “AUTO PRESET CH”,
“NO TV SIGNALS” is displayed on the TV screen.
• Channel setting will be saved even if the power fails.
• If you have Spanish or French menus and need English,
press [SET-UP]. Use [Cursor K/L] to select “IDIOMA” or
“LANGAGE”. Press [ENTER] to select “ENGLISH”.
Press [SET-UP] to remove the main menu.
• With regard only to the digital channel, even after the scanning is complete if you unplug the AC power cord before
turning off the unit by pressing [POWERy
y], the channel
setting may be lost.
2 Use [Cursor K /L] to select “LANGUAGE”,
then press [ENTER] repeatedly to change the setting.
e.g.) digital TV mode
--- CHANNEL SETUP --ADD/DELETE (DTV)
--- TV SETUP ---
AUTO PRESET CH (DTV)
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
! CATV takes approx. 50min.
or
• When aerial antenna is connected, select
“AUTO PRESET CH (TV)”, “AUTO PRESET CH (DTV)” or
“AUTO PRESET CH (TV/DTV)”.
• When connected to CATV, select
“AUTO PRESET CH (CATV)”.
• Scanning and memorizing the channels automatically
start.
e.g.) digital TV mode
D25
AUTO PRESET CH(DTV)
• When the scanning and memorizing are completed,
the lowest memorized channel will be displayed.
• When you selected “AUTO PRESET CH (TV/DTV)”, the
lowest memorized analog channel will be displayed
when the scanning and memorizing are completed.
If there is no analog channel, the lowest memorized
digital channel will be displayed.
12
EN
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
ENGLISH
ESPAÑOL
FRANÇAIS
3 Press [SET-UP] to exit.
INTRODUCTION
WATCHING TV
5 Channel Selection
5 Volume Adjustment
Select channels by pressing [CH. K / L] or [the Number buttons].
This section describes how to adjust the volume. The mute function, which
turns the sound off and on, is also described.
CONNECTION
• To select the memorized channels, use [CH. K / L] or
[the Number buttons].
• To select the non-memorized channels,
use [the Number buttons].
Use [VOL. X / Y] to adjust the audio volume.
To use [the Number buttons]
VOLUME
20
- When selecting analog channel 12
• The volume bar will be displayed at the bottom of the
TV screen when adjusting the volume.
• The volume bar display will automatically disappear in
a few seconds.
DTV
WATCHING TV
- When selecting digital channel 12-1
Press [MUTE] to turn off and on the sound.
20
• “MUTE” is displayed on the TV screen.
Press [MUTE] again or [VOL. X / Y] to recover the
original volume.
OPERATING DVD
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting
far surpasses analog broadcasting in both its picture
and sound quality.
MUTE
OPTIONAL SETTING
• When you select a channel larger than 100,
press [+10/+100] first.
Then use [the Number buttons] to press the lower
2-digit numbers.
DVD SETTING
What is the minor channel?
By using high compression technology, digital broadcasting offers a service that enables multiple signals to
send simultaneously.
Therefore, you can select more than one program per
major channel since digital broadcasting technology
distinguishes between multiple channels broadcast by
a single network.
NTSC (analog mode) [Air Time]
18:00
ATSC (digital mode)
CH4
No signal
INITIAL SETTING
TV
No signal
18:30
CH4
TROUBLESHOOTING
CH4
(high definition TV)
19:00
CH4
CH4-1
No signal
CH4
No signal
CH4-2
CH4
CH4-1
CH4-2
19:30
20:00
INFORMATION
20:30
major channel
: change automatically
: change manually by using [CH. / ]
minor channel
Although, you cannot watch the high definition TV
(HDTV) program, the unit converts the HDTV signal
down to the standard definition TV signal.
Note:
• “NO SIGNAL” will appear on the TV screen after the minor
channel broadcast is over.
13
EN
WATCHING TV
5 Switching Each Mode
DTV
You can easily switch with the remote control to the DTV (ATSC), TV (NTSC)
and DVD mode or to access an external device when they are connected to
the unit.
Press [SELECT] repeatedly to cycle through the input
mode.
In the digital mode, the detailed broadcasting information for the current
channel such as program title, the program guides are displayed.
Press [DISPLAY] repeatedly to cycle through the available display modes.
ANALOG MODE
OFF
DIGITAL MODE
BROADCASTING INFORMATION
EXTERNAL INPUT MODE
PROGRAM GUIDE
DVD MODE
• To use the video input jack on the front of the unit,
select “VIDEO”.
Note:
• When you switch the analog mode to the digital mode, it
may take a while until the digital channel selection is completed. The following TV screen is displayed while switching
the mode.
[Broadcasting Information]
• The following information is displayed.
1 channel number
2 broadcast station
3 program title
4 audio language
Press [MODE] repeatedly to cycle through the available audio languages.
(“OTHER” is displayed when the audio language cannot be acquired, or the acquired languages are other
than English, Spanish or French.)
NOW SCANNING
2
3
4
KABC
A Day of Memories
ENGLISH 1/3
CH 95-03
1
5 Screen Information
You can display the currently selected channel or other information such as
the audio mode on the TV screen.
TV
[Program Guide]
• The program guide added to broadcasting information is displayed.
In the analog mode, the current channel number is displayed.
Press [DISPLAY].
program
guide
KABC
CH 95-03
A Day of Memories
ENGLISH 1/3
A quarter-century ago, which may now
qualify as the good old days of newspapering, run-of-paper sales accounted
for 80 percent of the industry’s advertising revenues.
CH 10
Note:
• The current channel number is displayed at the topright corner of the TV screen.
• To clear the display, press [DISPLAY] again.
• When the program guide consists of more than 6 lines, use
[Cursor K / L] to scroll.
• “No description provided” is displayed when the program
guide is not provided.
• While the program guide is displayed, the closed caption
function is interrupted.
• In external input mode, the following screen is displayed;
e.g.) When an external device is connected to video input
jack.
VIDEO
• Available languages differ depending on the broadcast.
• The information display will automatically disappear in a
few seconds when the closed caption is on.
• Pressing [MODE] does not control external audio device.
14
EN
INTRODUCTION
5 TV Screen Display Mode
5 Sleep Timer
The sleep timer can be set to automatically turn off the unit after an
incremental period of time.
DTV
1 Press [SET-UP] to display the main menu.
CONNECTION
2 types of display modes can be selected in the digital mode when the
broadcasting station is sending 16:9 video signal.
1 Press [PICTURE/SLEEP] once.
INITIAL SETTING
2 Use [Cursor K / L] to select “DTV SETUP”, then
press [ENTER].
SLEEP
e.g.) digital TV mode
or
--- TV SETUP ---
• Sleep timer menu appears on the TV screen.
2 Use [Cursor { / B] to change the amount of time
until turn off the unit.
3 Use [Cursor K / L] to select “DTV DISPLAY”, then
or
--- DTV SETUP --DTV DISPLAY [LETTERBOX]
DTVCC
SLEEP
90MIN.
OPTIONAL SETTING
press [ENTER] repeatedly to switch the desired TV
aspect ratio.
or
WATCHING TV
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
OFF
OPERATING DVD
• You can set the unit to turn off after a set period of
time (from 30 to 120 minutes).
• Each time you press [Cursor { / B], the amount of
time will increase or decrease by 30 minutes.
• After set up, the sleep timer menu can be called up
for checking by pressing [PICTURE/SLEEP].
To Cancel the Sleep Timer
Use [Cursor { / B] at step 2 until “OFF“ is displayed
on the TV screen.
ZOOM
• The sleep timer setting display will automatically disappear
in a few seconds.
• When you disconnect the unit from the AC outlet or when a
power failure occurs, the sleep timer setting will be canceled.
TROUBLESHOOTING
[LETTERBOX]
Display the digital-supported program in full-screen.
Black borders will spread in the upper and lower
screen.
[ZOOM]
Enlarge and display the center area of the digital-supported program.
DVD SETTING
Note:
LETTERBOX
The right and left side of image will be cut off.
4 Press [SET-UP] to exit.
INFORMATION
Note:
• You may not switch the display mode depending on the
program.
15
EN
OPTIONAL SETTING
5 Channel Add/Delete
5 Picture Adjustment
The channel add/delete function lets you add the channel that was not
added by the auto channel scan due to the reception status at the initial
setting. You can also delete the unnecessary channels.
You can adjust brightness, contrast, color, tint and sharpness.
1 Press [SET-UP] to display the main menu.
1 Press [PICTURE/SLEEP] repeatedly until the desired
picture menu appears.
SLEEP
2
Use [Cursor K / L] to select “CHANNEL SETUP”, then
press [ENTER].
e.g.) digital TV mode
BRIGHT
CONTRAST
COLOR
--- TV SETUP ---
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
3
TINT
SHARPNESS
Use [Cursor K / L] to select “ADD/DELETE(DTV)” or
“ADD/DELETE”, then press [ENTER].
2 Within 10 seconds, use [Cursor { / B] to adjust the
quality.
or
e.g.) digital TV mode
or
--- CHANNEL SETUP --ADD/DELETE (DTV)
AUTO PRESET CH (DTV)
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
! CATV takes approx. 50min.
4
Select the channel you want to add or delete.
(Refer to “Channel Selection“ on page 13.)
e.g.) digital TV mode
D25
ADD/DELETE : DTV
5 Press [ENTER] repeatedly to select “ADD” or “DELETE”.
• To add or delete another channels, repeat steps 4 to 5.
• Color of channel number displayed at the right top of
the TV screen indicates;
- Blue: The selected channel will be added.
- Red: The selected channel will be deleted.
6 Press [SET-UP] to exit.
Note:
• “ADD/DELETE (DTV)” or “ADD/DELETE” menu will disappear
automatically in a few seconds.
• In the digital mode (DTV), you can add or delete channels
only for major channel.
• Once you delete a DTV channel, you cannot recover the
channel without performing auto channel scan again.
(Refer to “Auto Channel Scan” on page 12.)
16
EN
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
[Cursor { ]
[Cursor B]
to decrease brightness
to decrease contrast
to decrease color
to add purple
to make soft
to increase brightness
to increase contrast
to brighten color
to add green
to make clear
Note:
• The picture adjustment setting display will automatically
disappear in a few seconds.
INTRODUCTION
5 Closed Caption
Note:
TV
1 Press [SET-UP] to display the main menu.
[ENTER] repeatedly to change the setting.
e.g.) digital TV mode
--- TV SETUP ---
or
CAPTION1
CAPTION2
OPTIONAL SETTING
OFF
WATCHING TV
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
INITIAL SETTING
2 Use [Cursor K / L] to select “CAPTION”, then press
CONNECTION
You can view closed captioning (cc) for TV programs, movies and news.
Closed caption refer to text of dialogue or descriptions displayed on-screen
for the hearing impaired.
• To show the closed caption on your TV screen, broadcast
signal must contain the closed caption data.
• Not all TV programs and commercials have the closed caption or all types of the closed caption.
• Captions and texts may not match the TV voice exactly.
• Changing channels may delay the closed caption for a few
seconds.
• Adjusting or muting the volume may delay the closed caption for a few seconds.
• Abbreviations, symbols and other grammatical shortcuts
may be used in order to keep pace with the on-screen
action. This is not a problem with the unit.
• The caption or text characters will not be displayed while
the main menu or functions display is shown.
• If a black box appears on the TV screen, this means that
the closed caption is set to the text mode. To clear the box,
select “CAPTION1”, “CAPTION2” or “OFF”.
• If the unit receives poor quality television signals, the captions may contain errors, or there might be no captions at
all. Some possible causes of poor quality signals are:
- Automobile ignition noise
- Electric motor noise
- Weak signal reception
- Multiplex signal reception (ghosts or screen flutter)
• The unit retains the closed caption setting if the power fails.
• When your TV receives a special effects playback signal (i.e.,
Search, Slow and Still) from a VCR’s video output channel
(CH3 or CH4), the TV may not display the correct caption or
text.
TEXT1
OPERATING DVD
TEXT2
DVD SETTING
CAPTION1 and TEXT1;
are the primary caption and text services.
The captioning or text is displayed in the same
language as the program’s dialogue
(up to 4 lines of script on the TV screen, where it does
not obstruct relevant parts of the picture).
TROUBLESHOOTING
CAPTION2 and TEXT2;
are rarely available and broadcasters use them
only in special conditions, such as when “CAPTION1”
or “TEXT1” is not available.
• There are 3 display modes according to programs:
Paint-on mode: Displays input characters on the TV
screen immediately.
Pop-on mode: Once characters are stored in memory, they are displayed all at once.
Roll-up mode: Displays the characters continuously
by scrolling (max. 4 lines).
INFORMATION
3 Press [SET-UP] to exit.
17
EN
OPTIONAL SETTING
5 DTVCC Style
5 DTV Closed Caption
DTV
DTV
In addition to the basic closed caption described on page 17, DTV has its
own closed caption called DTVCC. Use this menu to change the settings for
DTVCC.
You can change the style of DTV CC such as font, color or size, etc.
1 Press [SET-UP] to display the main menu.
1 Press [SET-UP] to display the main menu.
2 Use [Cursor K / L] to select “DTV SETUP“, then press
2 Use [Cursor K / L] to select “DTV SETUP“, then press
[ENTER] .
[ENTER].
e.g.) digital TV mode
e.g.) digital TV mode
--- TV SETUP ---
or
--- TV SETUP ---
or
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
3 Use [Cursor K / L] to select “DTVCC“, then press
[ENTER] .
--- DTV SETUP ---
or
3 Use [Cursor K / L] to select “DTVCC“, then press
[ENTER] .
or
DTV DISPLAY [LETTERBOX]
DTVCC
4 Use [Cursor K / L] to select “CAPTION SERVICE“, then
press [ENTER] repeatedly to change the setting.
--- DTV CC
CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
or
--[OFF]
[OFF]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
OFF
Select if you do not want
DTVCC. This is the default.
SERVICE1~6
Select one of these before
changing any other item in
“CAPTION” menu. Choose
“SERVICE1/6” under normal
circumstances.
CAPTION SERVICE
5 Press [SET-UP] to exit.
Note:
• “CAPTION SERVICE” that you can switch differs depending
on the broadcast description.
18
EN
--- DTV SETUP --DTV DISPLAY [LETTERBOX]
DTVCC
4 Use [Cursor K /L] to select “USER SETTING“, then press
[ENTER] repeatedly to set to “ON”.
• Items in the dotted box are available only when
“USER SETTING“ is “ON“.
or
--- DTV CC
CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
--[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
5 Use [CursorK / L] to select an item, then press
[ENTER] repeatedly to change the setting for the item.
or
--- DTV CC
CAPTION SERVICE
USER SETTING
CAPTION SIZE
FONT STYLE
CHARACTER EDGE
FORE OPACITY
FORE COLOR
BACK OPACITY
BACK COLOR
--[SERVICE1/6]
[ON]
[MIDDLE]
[STYLE1/8]
[NONE]
[SOLID]
[WHITE]
[SOLID]
[BLACK]
INTRODUCTION
5 V-chip
V-chip reads the ratings for programs, then denies access to the programs
which exceed the rating level you set. With this function, you can block
certain programming inappropriate for children.
• CHARACTER EDGE
Edge type of the displayed caption can be switched
as below.
1 Press [SET-UP] to display the main menu.
2 Use [Cursor K / L] to select “V-CHIP SETUP“, then press
[ENTER].
e.g.) digital TV mode
• FORE COLOR, BACK COLOR
Font and background color of the displayed caption
can be switched as below.
--- TV SETUP ---
or
Proportional font used in the
menu screen
STYLE2/8
Monospaced with serifs
STYLE3/8
Proportionally spaced with
serifs
STYLE4/8
Monospaced with serifs
STYLE5/8
Proportionally spaced without serifs
STYLE6/8
Casual font type
STYLE7/8
Cursive font type
STYLE8/8
Small capitals
3 Use [the Number buttons] to enter the 4-digit numbers for your password.
PASSWORD
- - - -
• When you have not set up your password, enter 0000.
• When the password is correct, the following
“V-CHIP SETUP” menu is displayed.
e.g.) digital TV mode
FORE OPACITY
SOLID, TRANSLUCENT, FLASH
FORE COLOR
WHITE, BLACK, RED, GREEN, BLUE,
YELLOW, MAGENTA, CYAN, TRANSPARENT
C... “C. Change Password”
D page 21
BACK OPACITY
SOLID, TRANSLUCENT, FLASH
BACK COLOR
BLACK, RED, GREEN, BLUE, YELLOW,
MAGENTA, CYAN, TRANSPARENT, WHITE
D page 20
B... “B. MPAA Rating”D page 21
--- V--CHIP SETUP --TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
A
B
C
TROUBLESHOOTING
A... “A. TV Rating”
DVD SETTING
CHARACTER EDGE
NONE, RAISED, DEPRESSED, UNIFORM,
SHADOW LEFT, SHADOW RIGHT
6 Press [SET-UP] to exit.
OPERATING DVD
STYLE1/8
OPTIONAL SETTING
FONT STYLE
MIDDLE, LARGE, SMALL
WATCHING TV
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION
[OFF]
DTV SETUP
• FORE OPACITY, BACK OPACITY
Font and background opacity of the displayed caption
can be switched as below.
CAPTION SIZE
INITIAL SETTING
• FONT STYLE
Font style of the displayed caption can be switched as
below.
CONNECTION
• CAPTION SIZE
Closed captioning font size can be changed as below.
Note:
INFORMATION
• “DOWNLOADABLE RATING“ will be available when the unit
receives a digital broadcast using the new rating system.
• When you select a rating and set it to “BLOCK”, the higher
ratings will be blocked automatically. The lower ratings will
be available for viewing.
• When you set the highest rating to “VIEW”, all ratings turn
to “VIEW” automatically.
• If the “PROTECTED PROGRAM” message appears during
your TV viewing, change to a channel that is not blocked.
Then, you can access “V-CHIP SETUP” menu and change the
setting to allow all TV viewing.
• To block any inappropriate programming, set your limits in
both “TV RATING” and “MPAA RATING”.
• The V-chip setting will be retained after a power failure
(except the access code reverts to 0000).
19
EN
OPTIONAL SETTING
A. TV Rating
[To Set the Sub Ratings]
As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further
set the sub ratings to block specific elements of
programming. To set the sub ratings, follow the steps
below.
4 Use [Cursor K / L] to select “TV RATING“,
then press [ENTER].
e.g.) digital TV mode
--- V--CHIP SETUP ---
or
1 Use [Cursor K / L] to select the desired main rating,
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
then press [ENTER] twice to show its sub ratings.
or
TV-Y
TV-Y7 (DLSV)
TV-G
TV-PG (DLSV)
TV-14 (DLSV)
TV-MA (DLSV)
5 Use [Cursor K / L] to select the desired rating,
then press [ENTER] repeatedly to switch between
“VIEW” and “BLOCK”.
or
TV-Y
TV-Y7 (
TV-G
TV-PG (
TV-14 (
TV-MA (
2 Use [Cursor K / L], then press [ENTER] repeatedly
[VIEW]
) [VIEW]
[VIEW]
) [VIEW]
) [VIEW]
) [VIEW]
to change the setting.
e.g.) TV-PG
or
Rating
Category
TV-Y
Appropriate for all children
TV-Y7
Appropriate for all children 7 and
older
TV-G
General audience
TV-PG
Parental guidance suggested
TV-14
Unsuitable for children under 14
TV-MA
Mature audience only
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
lower
Sub Rating
higher
TV-PG
[BLOCK]
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Category
Rating
FV
Fantasy Violence
TV-Y7
V
Violence
S
Sexual Situation
L
Coarse Language
TV-PG
TV-14
TV-MA
D
Suggestive Dialogue
TV-PG, TV-14
6 Press [SET-UP] to exit.
Note:
• Blocked sub ratings will appear beside the main rating category in “TV RATING” menu.
• You cannot block a sub rating (D, L, S or V) if the main rating
is set to “VIEW”.
• Changing the category to “BLOCK” or “VIEW” automatically
changes all its sub ratings to the same (“BLOCK” or “VIEW”).
20
EN
C. Change Password
Although the default code “0000” is supplied with the unit, you can set
your own password.
4 Use [Cursor K / L] to select “MPAA RATING”,
4 Use [Cursor K / L] to select
CONNECTION
MPAA Rating is the rating system created by MPAA (Motion Picture Association of America).
then press [ENTER].
INTRODUCTION
B. MPAA Rating
“CHANGE PASSWORD”, then press [ENTER].
e.g.) digital TV mode
e.g.) digital TV mode
--- V--CHIP SETUP ---
--- V--CHIP SETUP ---
or
or
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
or
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
enter the new 4-digit password.
• Enter password again in “CONFIRM PASSWORD”
space.
NEW PASSWORD
_ _ _ _
OPTIONAL SETTING
G
PG
PG-13
R
NC-17
X
5 Press [the Number buttons] on the remote control to
WATCHING TV
change the setting.
INITIAL SETTING
5 Use [Cursor K / L], then press [ENTER] repeatedly to
TV RATING
MPAA RATING
DOWNLOADABLE RATING
CHANGE PASSWORD
CONFIRM PASSWORD
_ _ _ _
Rating
Category
General audience
PG
Parental guidance suggested
PG-13
Unsuitable for children under 13
R
Restricted; under 17 requires accompanying
parent or adult guardian
NC-17
No one under 17 admitted
X
Mature audience only
Note:
• Make sure new password and confirm password must be
exactly the same. If they are different, the space is cleared
for reentering.
• Your password will be erased and return to the default
(0000) when a power failure occurs. If you forget the password, unplug the power cord for 30 seconds to restore the
password to 0000.
DVD SETTING
6 Press [SET-UP] to exit.
6 Press [SET-UP] to exit.
OPERATING DVD
G
TROUBLESHOOTING
INFORMATION
21
EN
OPERATING DVD
DVD Functions
5 Playable Media
Type of media
Mark (logo)
DVD-video
*1, 2, 4, 6, 10, 11
DVD-RW
DVD-R
* 1, 3, 4, 5,
6, 7, 8, 9, 10
DVD+RW
DVD+R
* 1, 4, 5, 6,
9, 10
audio CD
* 4, 6, 10
Region code
1
Recorded
signals
Media size
Disc types
or ALL
-
e. g.)
digital video
(MPEG2)
title 1
title 2
chapter 1 chapter 2 chapter 3 chapter 4 chapter 1 chapter 2
5 inches
(12 cm)
or
3 inches
(8 cm)
e. g.)
digital audio
CD-RW
CD-R
* 4, 5, 6, 9,10
track 1
track 2
track 3
track 4
track 5
track 6
-
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1:
*2:
*3:
*4:
*5:
*6:
This unit conforms to the NTSC color system. Discs recorded in other color system such as PAL cannot be played back.
Certain DVD-video does not operate as described in this manual due to the intentions of the disc’s producers.
Discs recorded in VR (video recording) format cannot be played back.
Scratched or stained discs may not be played back.
Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or special properties of discs.
You can play back discs which bear the marks above. If you use non-standardized discs, this unit may not play them back. Even if they are
played back, the sound or video quality will be compromised.
*7: You may play back the unfinalized DVD-RW/-R recorded in the video format on our brand’s DVD recorder. However, depending on the
recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth, etc.). In this case,
you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.
*8: Only the discs recorded in the video format and finalized can be played back. Unfinalized discs cannot be played back. Depending on the
recording status of a disc, the disc may not be played back at all or the picture or sound may not be smooth, etc.
*9: If the recorded portion of the disc is too small (less than 2 3/16 inches (55 mm) across), it may not play back properly.
*10: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region format can only be played back on
unit with the same region code.
5 Unplayable Media
• NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM, DVD-audio, CD-i, photo CD, video CD, DVD with region codes other than 1 or ALL, DTS-CD,
DVD-ROM for personal computers, CD-ROM for personal computers, CD-RW/-R with MP3 files
• On the following disc, the sound MAY NOT be heard.
super audio CD
Note:
• Only the sound recorded on the normal CD layer can be delivered. The sound recorded on the high density super audio CD layer cannot be delivered.
• Any other discs without compatibility indications
22
EN
5 Playback
INTRODUCTION
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
Note:
Turn on the amplifier and any other device which is connected to this unit.
Make sure the external audio receiver (not supplied) are set to the correct
input mode.
5 Disc Menu
DVD
2 Press [OPEN/CLOSE A].
• The unit switches to the DVD mode when the unit
was in TV mode.
Press [DISC MENU] to call up the disc menu, or press
[TITLE] to call up the title menu.
Use [Cursor K / L / s / B] to select an item, then press
[ENTER] (or [PLAY B]).
Note:
• Menu operations may vary depending on the disc.
Refer to the manual accompanying the disc for more details.
Align the disc to the
disc tray guide.
4 Press [PLAY B]. The tray will close and playback will
start.
Resume ON
Press 'PLAY' to play from here.
To play the beginning,
press 'STOP' first and then 'PLAY'.
Note:
5 Press [STOP C] to stop playback temporarily.
Press [PAUSE F] during playback.
• Playback will be paused and sound will be
muted.
INFORMATION
• If playback remains stopped for 5 minutes, the screen
saver program will activate automatically,
and in 15 minutes with no activity at the unit, the unit
will turn off when “AUTO POWER OFF“ is set to “ON“
(factory default).
5 Pause
TROUBLESHOOTING
• If playback does not start automatically, press
[PLAY B] again.
• To cancel resume, press [STOP C] one more time in the stop
mode. On some discs, [STOP C] will not work while the resume
message appears. Please wait until the message disappears.
• The resume information will be kept even when unit is turned
off. However, opening the disc tray will cancel the resume feature. Playback will start at the beginning the next time you
insert the disc.
DVD SETTING
Press [STOP C] during playback.
Resume message will appear on
the TV screen.
Press [PLAY B]. Playback will
resume from the point at which
playback was stopped.
OPERATING DVD
• In case the DVD was recorded on both sides, make
sure the side you want to play back is facing up.
5 Resume Playback
OPTIONAL SETTING
3 Insert a disc with its label side facing up.
WATCHING TV
Some discs contain disc menus which describe the contents of the disc or
allow you to customize disc playback, or title menu which lists the titles
available on the DVD.
INITIAL SETTING
1 Press [POWERy] to turn on the unit.
• “ ” may appear at the top-right on the TV
screen when the operation is prohibited by
the disc or this unit.
• Some DVD may start playback from title 2 or 3 due to specific
programs.
• During the playback of a 2-layered disc, pictures may stop for
a moment. This happens while the 1st layer is being switched
to the 2nd layer. This is not a malfunction.
CONNECTION
Before you begin:
To continue playback, press [PLAY B].
6 Press [OPEN/CLOSE A] to eject the disc.
23
EN
OPERATING DVD
5 Step-by-step Playback
5 Zoom
DVD
DVD
The zoom function allows you to enlarge the video image and to pan
through the enlarged image.
Each time you [PAUSE F] in the pause
mode, the disc goes forward one frame at a
time.
1 During playback, press [MODE] repeatedly until “
” appears.
To continue playback, press [PLAY B].
OFF (ZOOM)
Note:
• Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in
the pause mode are blurred. (Refer to page 33.)
5 Fast Forward / Fast Reverse
2 Press [ENTER] repeatedly to change the zoom factor;
“OFF (ZOOM)“, “1.3x (ZOOM)”, “2x (ZOOM)“ or “4x (ZOOM)“.
Press [REV h] or [FWD /g] repeatedly
during playback to select the required
forward or reverse speed.
2x (ZOOM)
E1
To continue playback, press [PLAY B].
Note:
• Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in
the fast playback mode are blurred. (Refer to page 33.)
• Fast forward / fast reverse speed varies with disc.
Approximate speed is 1(2x), 2(8x), 3(20x), 4(50x) and 5(100x)
on DVD and 1(2x), 2(8x) and 3(30x) on audio CD.
• For DVD, sound will be muted during the search.
• For audio CD, sound will be intermittent during the search.
3 Once a desired zoom factor is set, press [RETURN
] to
display the position guide, then use
[Cursor K/ L/ s / B] to slide the zoomed picture
across the TV screen.
5 Slow Forward / Slow Reverse
4 To exit zoom, repeat steps 1 to 2 above and press
DVD
Press [REV h] or [FWD /g] repeatedly
during the paused mode to select the
required forward or reverse speed.
[ENTER] until “OFF (ZOOM)“ appears.
1
To continue playback, press [PLAY B].
Note:
• Slow forward / slow reverse speed varies with disc.
Approximate speed is 1(1/16x), 2(1/8x) and 3(1/2x).
• Set “STILL MODE” to “FIELD” in “DISPLAY“ menu if pictures in
the slow playback mode are blurred. (Refer to page 33.)
• The sound will be muted during slow forward/slow reverse
playback.
24
EN
Note:
• The gray box with an inner blue box that shows during
zoomed playback is the position guide indicates the position
of the zoomed image within the overall image.
Position guide stays on the TV screen until you press [ENTER].
Press [ENTER] one more time to recall the position guide
when disappears.
• Zoom function does not work while the disc menu is displayed.
• 4x zoom is not available on some discs.
• Zoom function is also available during pause mode.
INTRODUCTION
5 Search Functions
Chapter / Title Search
CONNECTION
DVD
Track Search
CD
Using [MODE]
Using [MODE]
playback, press [MODE] repeatedly until
1 During
“
“ appears.
1 During playback, press [MODE] repeatedly until
“
“ appears.
INITIAL SETTING
• If you want to perform the title search, press
[Cursor K / L] repeatedly until “ “ appears.
2 Press [the Number buttons] to select your desired
2
track within 60 seconds.
WATCHING TV
Press [the Number buttons] to select your desired
chapter or title within 60 seconds.
/29 (SEARCH)
/12 (SEARCH)
OPTIONAL SETTING
To play back a single-digit chapter or title when there
are more than 10 chapters or titles, press [ENTER] after
entering the chapter or title number.
To play back a single-digit track when there are more
than 10 tracks, press [ENTER] after entering the track
number.
3 Playback will start automatically from the track you
selected.
will start automatically from the chapter or
3 Playback
title you selected.
• The total number of chapters/titles in your disc; with less than
10 chapters/titles, press the chapter/title number directly.
With 10 or more chapters/titles, to play back a single digit
chapter/title, press [0] first, then the chapter/title number.
(e.g., for chapter 3, press [0] and [3].) To play back a doubledigit chapter/title, press the chapter/title number.
• The total number of tracks in your disc;
with less than 10 tracks, press the track number directly.
with 10 or more tracks, to play back a single digit track, press
[0] first, then the track number. (e.g., for track 3, press [0]
and [3].) To play back a double-digit track, press the track
number.
• Track search is not available for programmed or random
playback.
playback, press [SKIP H / G] repeatedly
1 During
until a desired chapter or title will be selected.
DVD SETTING
Using [SKIP H / G]
Using [SKIP H / G]
1 During playback, press [SKIP H / G] repeatedly
until your desired track will be selected.
current chapter
current track
(TR)
(CH)
CH 1 CH 2 CH 3 CH 4
[SKIP H]
[SKIP G]
or
current title
or
TR 1 TR 2 TR 3 TR 4
[SKIP H]
[SKIP G]
TROUBLESHOOTING
or
OPERATING DVD
Note:
Note:
(TT)
TT 1 TT 2 TT 3 TT 4
[SKIP H]
[SKIP G]
(If the disc has no chapters.)
Note:
• [SKIP H / G] are not available when playback is stopped.
• Chapter/title search can only be performed during playback or
when the unit has kept the resume information. It cannot be
performed in the stop mode.
• Chapter/title search is not available with some DVD.
selected.
Note:
• [SKIP H / G] are not available when playback is stopped.
• Track search can only be performed during playback or when
the unit has kept the resume information. It cannot be
performed in the stop mode.
INFORMATION
will start automatically from the chapter or
2 Playback
title you selected.
2 Playback will start automatically from the track you
25
EN
OPERATING DVD
5 Repeat Playback
You can repeat playback chapters, titles or tracks on a disc.
Time Search
1 During playback, press [MODE] repeatedly until
“
1 During playback, press [MODE] repeatedly until
“
“ /“
“ appears.
e.g.) DVD
/12 (SEARCH)
2 Use [Cursor K / L] repeatedly until “
TOTAL
or
“ appears.
2 Press [Cursor K / L] to change the repeat mode.
DVD
“ appears.
1:29:00
OFF
(repeat off)
CHAPTER
(current chapter repeat)
TITLE
(current title repeat)
OFF
(repeat off)
TRACK
(current track repeat)
ALL
(entire disc repeat)
CD
3 Press [the Number buttons] to select your desired
time lapse within 60 seconds.
TOTAL
1:29:00
3 Press [RETURN
] to exit.
4 Playback will start automatically from the time you
selected.
Note:
• When there is no need to enter a number, “0” appears
automatically. For example, “0: 0_ : _ _” appears in time
search menu if the total time of the title or track is less than 10
minutes.
• Press [CLEAR] to erase the incorrect input at step 3.
• Time search can only be performed during playback or
when the unit has kept the resume information. It cannot be
performed in the stop mode.
Direct Search
5 Repeat A-B Playback
You can repeat playback between A and B on a disc.
1 During playback, press [MODE] repeatedly until
“A
B
OFF“ appears.
2 Press [ENTER] at your desired starting point A.
A B A-
Press [the Number buttons] to select your desired
chapter, title or track.
(A-B REPEAT)
3 Press [ENTER] at your desired ending point B.
A B A-B (A-B REPEAT)
• Point B should be in the same title or track as point A.
• Within a few seconds, the section A-B will begin to
play back repeatedly.
Note:
• To select a single-digit chapter, title or track number, press the
number directly.
• To select double-digit chapter, title or track number:
- If the disc contains more than 9 and less than 100 chapters,
titles or tracks, press [+100/+10] first, then enter the doubledigit chapter, title or track number.
(e.g., for track 26, press [+100/+10], [2] and [6].)
26
EN
4 To cancel repeat A-B playback, press [MODE] repeatedly until “ A B A-B“ appears.
Press [ENTER] so “ A B OFF” appears.
2 Use [Cursor K / L] to select a desired track, then press
[ENTER] to store.
• Additional tracks may be on other screens. Use
[Cursor K/ L] to go on to the next / previous pages.
• Repeat this step until you have selected all the tracks
you wish to play back in the program.
or
PROGRAM
TOTAL
0:08:22
T 15 3:18
T 16 4:24
ALL CLEAR
T 4
T 16
3:58
4:24
PLAY
CLEAR
CD
1 In stop mode, press [MODE] repeatedly until
“RANDOM” menu appears.
1/ 1
T 16 4:24
• Up to 99 tracks can be ordered.
• If 8 or more tracks were in a program, use
[SKIP H / G] to see all the tracks.
WATCHING TV
This function shuffles the playing order of tracks instead of playback in the
sequence.
3/ 3
INITIAL SETTING
CD-DA
ENTER
5 Random Playback
CONNECTION
• Repeat setting (except “ALL“) will be cleared when moving to
another title, chapter or track.
• During programmed playback, repeat setting will be effective
for the tracks in the program.
• Repeat playback or repeat A-B playback may not available
with some discs.
• Repeat A-B playback does not function during other repeat
mode.
• To cancel point A, press [CLEAR] at step 2 in “Repeat A-B
Playback“.
• Stopping playback will cancel repeat A-B playback.
INTRODUCTION
Note:
3 Press [PLAY B] to start programmed playback.
RANDOM
TOTAL 0:45:55
OPTIONAL SETTING
CD-DA
RANDOM PROGRAM
--no indication--
Note:
PLAY
2 Press [PLAY B] to start random playback.
5 Programmed Playback
You may determine the order in which tracks will be played back.
1 In stop mode, press [MODE] repeatedly until the
“PROGRAM” menu appears.
PROGRAM
ENTER
PLAY
CLEAR
T
T
T
T
T
T
T
1
2
3
4
5
6
7
TOTAL
0:00:00
3:31
4:28
4:19
3:58
4:12
4:02
3:55
1/ 3
T 1 3:31
1/ 1
INFORMATION
CD-DA
TROUBLESHOOTING
CD
DVD SETTING
• To repeat the current track in the random mode, follow the
steps 1 and 2 in “Repeat Playback“ on page 26 and select
“
TRACK“.
• To repeat the entire random selections, follow the steps 1 and
2 in “Repeat Playback“ on page 26 and select “
ALL“.
• Random playback will be kept until you press [STOP C].
OPERATING DVD
Note:
• Press [CLEAR] to erase the last track in the program if you
make an error.
• To erase all programmed tracks at once, select “ALL CLEAR’’
and press [ENTER] at step 2.
• While a program is being played back, [STOP C] works as
follows:
- Pressing [STOP C] once: The track will be in the resume
standby mode. Next time you press [PLAY B], the playback
will resume from the point where it is stopped in the
programmed playback.
- Pressing [STOP C] twice: Resume mode will be canceled.
Next time you press [PLAY B], playback will restart from the
first track in the original order. However, your programmed
playback can be restarted when you follow the above steps.
(Your programs are still stored until either the disc is ejected
or the unit is turned off.)
- On some discs, [STOP C] will not work while the resume
message appears. Please wait until the message disappears.
• To repeat the current track in the program, follow the steps 1
and 2 in “Repeat Playback“ on page 26 and select
“
TRACK“.
• To repeat the entire program, follow the steps 1 and 2 in
“Repeat Playback“ on page 26 and select “
ALL“.
• Turning off the unit or opening the disc tray will erase the
program.
• You cannot use [the Number buttons] to select another
track during programmed playback. Use [REV h] or
[FWD g] to select other tracks in the program.
• You cannot combine random playback with programmed
playback.
• You cannot alter a programmed order during playback.
• You can start programmed playback only while in
“PROGRAM“ menu.
27
EN
OPERATING DVD
5 On-screen Display
You can check the information about the current disc by pressing [DISPLAY] on
the remote control.
DVD
CD
appears only when multiangle is available on the DVD
current playback status
current playback status
1
1
11/16 0:00:00 - 0:03:30
4/12 0:03:21 - 0:02:15
T
remaining time of the current
track
elapsed time of the current track
remaining time of the current
chapter
elapsed time of the current
chapter
CH (chapter):
current chapter number /
total chapters
2
1/3
0:00:00 - 1:23:45
remaining time of the current title
TR (track):
current track number /
total tracks
2
4/12 0:13:45 - 0:45:40
current repeat setting
appears only when the
repeat setting is active.
T : Track repeat
A : All tracks repeat
A B : A-B repeat
remaining time of the entire disc
elapsed time of the current title
TT (title):
current title number / total titles
3
elapsed time of the entire disc
T L1
layer numbers, appears only when
playing back a 2-layered disc.
L0 : Layer 0 is playing back
L1 : Layer 1 is playing back
current repeat setting appears
only when the repeat setting is
active.
C : Chapter repeat
T : Title repeat
A B : A-B repeat
bit rate indication for the amount
of audio and video data currently
being read
4
28
EN
T
ALL:
current track number /
total tracks
3
Note:
• When you are playing back a disc in program or random
mode, “
PROGRAM” (or “
RANDOM”) will be displayed
instead of 2 .
INTRODUCTION
5 Special Settings
Subtitle Language
Audio Language
This unit allows you to select a subtitle language (if available) during DVD
playback.
This unit allows you to select an audio language (if multiple languages are
available) during DVD playback.
1 During playback, press [MODE] repeatedly until
1 During playback, press [MODE] repeatedly until
“
“ appears.
“ appears.
2 Use [Cursor K / L] repeatedly until the desired
language appears.
language appears.
1.ENG Dolby D 3/2.1ch 48k/3
or
audio can be varied on
the displayed number.
current audio language.
or
subtitles can be varied on
the displayed number.
current subtitle language.
(Spanish audio)
FRE
(French audio)
...
(French subtitles)
...
FRE
SPA
Note:
To cancel the subtitle
1 During playback, press [MODE] repeatedly until
“ appears.
2 Use [Cursor K / L] repeatedly until “
OFF
(SUBTITLE)“ appears.
Camera Angles
OFF (SUBTITLE)
TROUBLESHOOTING
or
DVD
Note:
Some DVD may contain scenes which have been shot
simultaneously from various angles. You can change the
camera angle if “ ” appears on the TV screen. If “ANGLE ICON”
is set to “OFF” in “OTHERS” menu, “ ” will not appear.
(Refer to page 36.)
1 During playback, press [MODE] repeatedly until
“
INFORMATION
• If your language is not shown after pressing [Cursor K / L]
several times, the disc may not have that language. However,
some discs only allow you to change subtitle languages setting in the disc menu. (Operation varies depending on the
disc, so refer to the manual along with the disc.)
• When “NOT AVAILABLE” appears on the TV screen, it means
no subtitle is recorded on the scene.
• If you choose a language that has 3-letter abbreviation, the
abbreviation will be displayed every time you change the
subtitle language setting. If you choose any other languages,
“---” will be displayed instead. (Refer to page 37.)
• Opening the disc tray will cancel your subtitle setting.
DVD SETTING
• Some discs will only allow you to change the audio setting
from the disc menu. Refer to the manual accompanying the
discs for details.
• If your language is not shown after using [Cursor K / L]
several times, the disc may not have that language. However,
some discs allow you to change multiple audio languages
setting in the disc menu. (Operation varies depending on the
disc, so refer to the manual along with the disc.)
• When “NOT AVAILABLE“ appears on the TV screen, it means
audio language is not available.
OPERATING DVD
(English subtitles)
• Each time you press [Cursor K / L], the audio
language changes as example below.
ENG
(English audio)
OPTIONAL SETTING
• Each time you press [Cursor K / L], the subtitle
language changes as example below.
OFF
(no subtitles)
ENG
WATCHING TV
1.ENG/6 (SUBTITLE)
“
INITIAL SETTING
2 Use [Cursor K / L] repeatedly until your desired
“
CONNECTION
DVD
DVD
“ appears.
2 Use [Cursor K / L] repeatedly until your desired camera angle appears.
1 / 8 (ANGLE)
or
angles can be varied on
the displayed number.
29
EN
OPERATING DVD
Black Level Setting
Virtual Surround
You can enjoy virtual surround on your existing 2 channel stereo system.
DVD
Adjust the black level to make the dark areas of the TV picture brighter.
1 During playback, press [MODE] repeatedly until
1 During playback, press [MODE] repeatedly until
2 Use [Cursor K / L] to adjust the black level.
2 Use [Cursor K / L] to select the sound level.
“
“ appears.
“
“ appears.
OFF (BLACK LEVEL)
or
ON : Makes the dark areas brighter.
OFF : Shows the original picture as recorded.
3 Press [RETURN
] to exit.
1 (SURROUND)
or
1
: Natural effect
2
: Emphasized effect
OFF : No effects (original sound)
3 Press [RETURN
] to exit.
Note:
• The setting will be kept even if the unit is turned off.
Stereo Sound Mode
CD
This unit allows you to select a sound mode during audio CD playback.
1 During playback, press [MODE] repeatedly until
“
” appears.
2 Use [Cursor K / L] repeatedly until the desired sound
mode appears.
or
STEREO (AUDIO)
• Each time you press [Cursor K / L], the sound mode
changes as example below.
STEREO (stereo sound with left and right channels)
L-ch
(left channel sound only)
R-ch
(right channel sound only)
Note:
• Virtual surround cannot be changed when the sound mode is
set to either “L-ch” or “R-ch”.
30
EN
Note:
• The setting will be kept even if the unit is turned off.
• For audio CD, virtual surround will not be effective if the
sound mode is set to something other than “STEREO”.
See “Stereo Sound Mode”.
• Turn down the level or select “OFF” if the sound is distorted.
INTRODUCTION
Marker Setup
To return to the marker later
To set a marker
1 During playback, press [MODE] repeatedly until
“
”/“
CONNECTION
This feature allows you to assign a specific point on a disc to be called back
later.
” appears.
1 To select a desired marker, repeat steps 1 to 3 in
“To set a marker“.
e.g.) DVD
INITIAL SETTING
e.g.) DVD
/12 (SEARCH)
2 Use [Cursor K /L] repeatedly until marker search menu 2 Press [ENTER] at the desired marker to start playback
appears.
from the specific point which you set.
WATCHING TV
or
within 60 seconds.
or
4 When the playback reaches the point at which you
• Marker search menu will disappear in about 60 seconds
when there is no input.
• You can mark up to 10 points.
• To clear a marker, select the marker to be cleared, and then
press [CLEAR].
• Ejecting the disc or turning off the power will erase all markers.
• Selecting “ ” at step 3 in the section “To set a marker”
will also erase all markers.
OPERATING DVD
want to set a marker, press [ENTER].
Note:
OPTIONAL SETTING
3 Use [Cursor s / B] to select an available marker
• Marker is now set.
] to exit.
DVD SETTING
5 Press [RETURN
TROUBLESHOOTING
INFORMATION
31
EN
DVD SETTING
Settings are only effective when the unit is in DVD mode and any discs should not be played back.
QUICK MENU AT A GLANCE
If you make setting for “TV MODE“ or “DOLBY DIGITAL”,
you can also enter from the “QUICK“ menu.
In stop mode, press [SET-UP] to display the “SETUP”
menu first, then use [Cursor K /L] to select “QUICK”
and press [ENTER].
SETUP
5 Use [Cursor K /L] to select the desired item, then press
[ENTER].
[AUDIO] *1, *2
(Default: ORIGINAL)
Select the desired audio language.
SETUP
or
QUICK
TV MODE
DOLBY DIGITAL
SELECT:K/L
EXIT:SETUP
LANGUAGE
AUDIO
ORIGINAL
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
4:3 LETTER BOX
BITSTREAM
SELECT:K/L
EXIT:SETUP
[SUBTITLE] *1, *2
SET:ENTER
CANCEL:RETURN
SET:ENTER
CANCEL:RETURN
(Default: OFF)
Select the desired subtitle language.
SETUP
or
5 DVD Language Setting
You can change the desired language when playing back the disc.
LANGUAGE
SUBTITLE
OFF
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
1 In stop mode, press [SET-UP] to display the “SETUP”
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
menu.
[DISC MENU] *1
(Default: ENGLISH)
Select the desired language in DVD menu.
2 Use [Cursor K /L] to select “CUSTOM”, then press
SETUP
or
[ENTER].
SETUP
or
QUICK
CUSTOM
INITIALIZE
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
3 Use [Cursor K /L] to select “LANGUAGE”, then press
[ENTER].
SETUP
or
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
4 Use [Cursor K /L] to select the desired item, then press
SETUP
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
SELECT:K/L
EXIT:SETUP
32
EN
ORIGINAL
OFF
ENGLISH
SET:ENTER
CANCEL:RETURN
SET:ENTER
CANCEL:RETURN
Note:
• To change the on-screen language, press [SELECT] to
switch the unit to TV mode first. Press [SET-UP] to display
“TV SETUP” menu, then set the desired language. (Refer to
“Language Selection“ on page 12.)
*1
• Language options are not available with some discs.
• If “OTHER” is selected in “AUDIO”, “SUBTITLE” or “DISC MENU”
menu, press 4-digit number to enter the code for the desired
language. (Refer to “Language Code List” on page 37.)
• Only the languages supported by the disc can be selected.
*2
• Use [MODE] to select audio and subtitles available on the
DVD.
• If the DVD’s default settings for audio and subtitle are the
same language, the subtitles may not show unless you turn
them on.
[ENTER].
or
LANGUAGE
DISC MENU
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
DUTCH
6 Press [SET-UP] to exit.
INTRODUCTION
5 Display Setting
You can change the TV aspect ratio and still mode clarity in “DISPLAY”
menu.
5 Use [Cursor K /L] to select the desired item, then press
[ENTER].
[TV MODE]
(Default: 4:3 LETTER BOX)
Select the desired TV aspect ratio.
SETUP
or
[ENTER].
INITIAL SETTING
2 Use [Cursor K /L] to select “CUSTOM”, then press
DISPLAY
TV MODE
4:3 LETTER BOX
4:3 PAN & SCAN
SETUP
or
QUICK
CUSTOM
INITIALIZE
SELECT:K/L
EXIT:SETUP
[STILL MODE]
SET:ENTER
CANCEL:RETURN
WATCHING TV
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
(Default: AUTO)
Select the desired still mode.
3 Use [Cursor K /L] to select “DISPLAY”, then press
SETUP
or
SETUP
or
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
[ENTER].
SETUP
DISPLAY
SELECT:K/L
EXIT:SETUP
4:3 LETTER BOX
AUTO
Note:
TV MODE:
• Select “4:3 LETTER BOX”, so that black bars may appear on
the top and bottom of the TV screen.
• Select “4:3 PAN & SCAN” for a full height picture with both
sides adjusted.
STILL MODE:
• Select “AUTO” usually.
• If you select “FIELD”, the picture in the still mode will be
stabilized.
• If you select “FRAME”, the picture in the still mode will be
highly defined.
DVD SETTING
TV MODE
STILL MODE
SET:ENTER
CANCEL:RETURN
OPERATING DVD
4 Use [Cursor K /L] to select the desired item, then press
or
DISPLAY
STILL MODE
AUTO
FIELD
FRAME
OPTIONAL SETTING
[ENTER].
CONNECTION
1 In stop mode, press [SET-UP] to display “SETUP” menu.
SET:ENTER
CANCEL:RETURN
TROUBLESHOOTING
6 Press [SET-UP] to exit.
INFORMATION
33
EN
DVD SETTING
5 DVD Audio Setting
Choose the appropriate audio settings for your device. It only affects during
the playback of DVD.
1 In stop mode, press [SET-UP] to display “SETUP” menu.
2 Use [Cursor K /L] to select “CUSTOM”, then press
5 Use [Cursor K /L] to select the desired item, then press
[ENTER].
[DRC] (dynamic range control) (Default: ON)
Select “DRC”.
This function is available only on the discs which are
recorded in the Dolby Digital format.
[ENTER].
SETUP
or
SETUP
or
QUICK
CUSTOM
INITIALIZE
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
SELECT:K/L
EXIT:SETUP
ON
ON
BITSTREAM
SET:ENTER
CANCEL:RETURN
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
3 Use [Cursor K /L] to select “AUDIO”, then press
ON : Compress the range between soft and loud
sounds.
OFF : No effects (original sound).
[ENTER].
SETUP
or
[DOWN SAMPLING]
CUSTOM
(Default: ON)
Select “DOWN SAMPLING”.
This function is available only on digital outputting of a
disc recorded in 96kHz.
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SELECT:K/L
EXIT:SETUP
SETUP
SET:ENTER
CANCEL:RETURN
or
4 Use [Cursor K /L] to select the desired item, then press
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
BITSTREAM
[ENTER].
SELECT:K/L
EXIT:SETUP
SETUP
or
SET:ENTER
CANCEL:RETURN
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
ON
BITSTREAM
ON : When outputting in 48kHz.
OFF : When outputting the original sound.
Note:
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
• When playing back a 96 kHz disc with the copyright protection or when virtual surround is set to 1 or 2, the sound will
be down sampled at 48 kHz even if “DOWN SAMPLING” is
“OFF”.
[DOLBY DIGITAL]
(Default: BITSTREAM)
Select “BITSTREAM“ when this unit is connected to a
Dolby Digital decoder. Available on DVD only.
SETUP
or
AUDIO
DRC
DOWN SAMPLING
DOLBY DIGITAL
SELECT:K/L
EXIT:SETUP
ON
ON
BITSTREAM
SET:ENTER
CANCEL:RETURN
BITSTREAM : Outputs Dolby Digital signals.
PCM
: Converts the Dolby Digital into PCM.
(2 channel)
6 Press [SET-UP] to exit.
34
EN
6 Use [Cursor K /L] to select the desired item, then press
[ENTER].
SETUP
or
1 In stop mode, press [SET-UP] to display “SETUP” menu.
PARENTAL
PARENTAL LEVEL
ALL
8 [ADULT]
7 [NC-]7
6 [R]
5 [PGR]
4 [PG13]
3 [PG]
SELECT:K/L
EXIT:SETUP
SETUP
or
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
PARENTAL LEVEL
ALL
: All parental locks are canceled.
8 [ADULT]
: All ratings (adult/general/children) can
be played back.
7 [NC-17]-2 [G] : Only DVD intended for general use and
children can be played back.
1 [KID SAFE] : Only DVD intended for children can be
played back.
7 Press [SET-UP] to exit.
OPTIONAL SETTING
3 Use [Cursor K /L] to select “PARENTAL”, then press
[ENTER].
SETUP
or
CUSTOM
To change the password
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
5 Follow steps 1 to 4. Use [Cursor K /L] to select
SET:ENTER
CANCEL:RETURN
SETUP
or
4 Use [the Number buttons] to enter the 4-digit
OPERATING DVD
“PASSWORD CHANGE“, then press [ENTER].
SELECT:K/L
EXIT:SETUP
PARENTAL
PARENTAL LEVEL
ALL
PASSWORD CHANGE
number for your password, then press [ENTER].
SETUP
PARENTAL
PASSWORD
Please enter a 4-digit password.
SET:ENTER
CANCEL:RETURN
DVD SETTING
SELECT:K/L
EXIT:SETUP
6 Use [the Number buttons] to enter the new 4-digit
password, then press [ENTER].
CANCEL:RETURN
SETUP
SETUP
or
PARENTAL
PARENTAL LEVEL
ALL
PASSWORD CHANGE
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
Please enter a 4-digit password.
0
0
0
0
Don’t forget the password.
Press “ENTER” to activate password.
EXIT:SETUP
CANCEL:RETURN
INFORMATION
press [ENTER].
PARENTAL
PASSWORD
• If you have set password already, use [the Number
buttons] to enter the current 4-digit password.
•You cannot use the default password (4737) to play
back a DVD.
5 Use [Cursor K /L] to select “PARENTAL LEVEL“, then
TROUBLESHOOTING
EXIT:SETUP
WATCHING TV
QUICK
CUSTOM
INITIALIZE
SET:ENTER
CANCEL:RETURN
INITIAL SETTING
2
Use [Cursor K /L] to select “CUSTOM”, then press
[ENTER].
CONNECTION
Parental setting prevents your children from viewing inappropriate materials. (Password protected.) Playback will stop if the ratings exceed the levels
you set.
INTRODUCTION
5 Parental Setting
Note:
• DVD-video may not respond to parental lock settings. Make
sure this function works with your DVD-video.
• Record the password in case you forget it.
• If you forget the password, press [4], [7], [3], [7], then enter
your new password. Password will be cleared and parental
levels will be set to “ALL”.
• A power failure will not erase your password.
7 Press [SET-UP] to exit.
35
EN
DVD SETTING
5 Others
5 Use [Cursor K /L] to select the desired item, then press
You can change the other functions.
[ENTER].
1 In stop mode, press [SET-UP] to display “SETUP” menu.
[ANGLE ICON]
(Default: ON)
Set to “ON” to show the angle icon when multiple camera angles are available during DVD playback.
SETUP
or
2 Use [Cursor K /L] to select “CUSTOM”, then press
OTHERS
ANGLE ICON
AUTO POWER OFF
ON
ON
[ENTER].
SETUP
or
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
3
SETUP
SET:ENTER
CANCEL:RETURN
[ENTER].
SETUP
OTHERS
ANGLE ICON
AUTO POWER OFF
SELECT:K/L
EXIT:SETUP
EN
OTHERS
ANGLE ICON
AUTO POWER OFF
SELECT:K/L
EXIT:SETUP
4 Use [Cursor K /L] to select the desired item, then press
or
or
ON
ON
CUSTOM
LANGUAGE
DISPLAY
AUDIO
PARENTAL
OTHERS
SELECT:K/L
EXIT:SETUP
36
[AUTO POWER OFF]
(Default: ON)
Set to “ON” to turn this unit off automatically after 20
minutes of no use.
SETUP
Use [Cursor K /L] to select “OTHERS”, then press
[ENTER].
or
SET:ENTER
CANCEL:RETURN
SELECT:K/L
EXIT:SETUP
QUICK
CUSTOM
INITIALIZE
ON
ON
SET:ENTER
CANCEL:RETURN
6 Press [SET-UP] to exit.
SET:ENTER
CANCEL:RETURN
5 Language Code List
You can reset all the settings except for the parental setting and
on-screen menu language.
Language
[ENTER].
SETUP
or
QUICK
CUSTOM
INITIALIZE
SET:ENTER
CANCEL:RETURN
SETUP
or
INITIALIZE
Initialize?
NO
YES
SELECT:K/L
EXIT:SETUP
SET:ENTER
CANCEL:RETURN
• When you want to cancel the initialization, select “NO”
at step 3, then press [SET-UP].
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
INFORMATION
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
TROUBLESHOOTING
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
DVD SETTING
Note:
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
OPERATING DVD
4 Press [SET-UP] to exit.
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
Code
5964
5961
5960
6047
6051
6061
OPTIONAL SETTING
3 Use [Cursor K /L] to select “YES”, then press [ENTER].
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
Language
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish [POL]
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
WATCHING TV
SELECT:K/L
EXIT:SETUP
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
INITIAL SETTING
2 Use [Cursor K /L] to select “INITIALIZE”, then press
Code
CONNECTION
1 In stop mode, press [SET-UP] to display “SETUP” menu.
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech [CZE]
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
L-N
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
INTRODUCTION
5 Reset to the Default Setting
Note:
• If you choose a language that has a 3-letter abbreviation,
they will be displayed every time you change the audio or
subtitle language setting above. If you choose any other
language, ‘---’ will be displayed instead. (3-letter abbreviation is written in bracket.)
37
EN
TROUBLESHOOTING
5 Troubleshooting Guide
If the unit does not perform properly when operated as instructed in this owner’s manual, check the following chart
once before calling for service.
Symptom
Remedy
No power
• Be sure the power cord is plugged in.
• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
reset itself.
No picture or sound
• Check if the power is on.
• Check the outlet connection.
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Turn off the power and wait for about 1 minute, then turn it on again.
No color
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
• Adjust “COLOR” in “PICTURE“ menu.
Sound OK, picture poor
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• Adjust “CONTRAST” and “BRIGHT” in “PICTURE“ menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Adjust “CONTRAST” and “BRIGHT” in “PICTURE“ menu.
• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
T
V Picture blurred
38
EN
• When the outside antenna is used, check the wire condition and connection.
• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Bars on TV screen
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on TV
screen
• Move the unit away from nearby electric appliances. Turn off the power and wait
30 minutes before turning it back on.
• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some channels
• Check the antenna or cable connection to the main unit.
• When the outside antenna is used, check the wire condition and connection.
• Electrical interference from nearby appliances may affect picture quality.
• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor
• View other TV channels. The problem might be limited to the broadcasting station.
No reception of digital signals
• Make sure auto channel scan has been completed. (Refer to “Auto Channel Scan”
on page 12.)
Auto channel scan must be completed when you set up the unit for the first time
or move it to a location where previously unavailable channels are broadcast.
• The selected channel may not be broadcasting.
• When auto channel scan is interrupted and not completed, some channels will not
be received. Make sure to complete. (Refer to “Auto Channel Scan” on page 12.)
INTRODUCTION
• Many digital channels have alternate channel numbers. The unit changes the
numbers automatically to the ones signifying the broadcasting stations. These are
the numbers used for analog broadcasts.
Remote control does not work
• Check the antenna or cable connection to the main unit.
• Check the batteries of the remote control.
• Check if there is an obstacle between the infrared sensor window and the remote control.
• Test the signal output. If OK, then possible remote sensor trouble.
(Refer to “IR Signal Check” on page 40.)
• Aim the remote control directly at the infrared sensor window on the front of the unit.
• Reduce the distance to the unit.
• Re-insert the batteries with their polarities (+/– signs) as indicated.
INITIAL SETTING
Remedy
The entered channel number
changes automatically
CONNECTION
Symptom
Problems with Closed Caption Feature
Misspelled captions are disT played.
• Closed captioning production companies may broadcast programs without correcting the misspelling in a live broadcast.
No caption is displayed when
playing back the cassette tape
containing captions.
• The cassette tape may be illegally copied, or the caption signal might not have
been read during copying.
Black box is displayed in the
TV screen.
• The text mode is selected for caption. Select “CAPTION1”, “CAPTION2” or “OFF”.
Completely distorted picture
or black/white picture with
DVD
• Make sure the disc is compatible with the unit.
Picture freezes momentarily
during playback.
• Check the disc for fingerprints/scratches and clean with a soft cloth wiping from
center to edge.
Disc cannot be played back.
• Clean the disc.
• Ensure the disc is correctly inserted.
• Check if the disc is defective by trying another disc.
• Cancel the parental lock or change the control level.
• Insert a correct disc that can be played back on this unit.
• Handle a disc with special care so that it does not have fingerprints, scratches, or
dusts on its surface.
Buttons do not work or the
D unit stops responding.
The unit does not respond to
some operating commands
during playback.
TROUBLESHOOTING
V
DVD SETTING
D
OPERATING DVD
• Interference from buildings or weather conditions may cause captioning to be
incomplete.
• Broadcasting station may shorten the program to insert advertisement. The closed
caption decoder cannot read the information of the shortened program.
OPTIONAL SETTING
Captions are displayed as a
white box.
No caption is displayed in the
Closed Caption-supported
program.
WATCHING TV
• Captions that are delayed a few seconds behind the actual dialogue are common for live
V Captions are not entirely displayed, or captions are delayed broadcasts. Most captioning production companies can display a dialogue to a maximum of 220 words per minute. If a dialogue exceeds that rate, selective editing is used to
behind the dialogue.
insure that the captions remain up-to-date with the current TV screen dialogue.
• To completely reset the unit, unplug the power cord from the power outlet for
5-10 seconds.
• Operations may not be permitted by the disc. Refer to the instructions of the disc.
• The angle cannot be switched for DVD which do not contain multiple angles. In
some cases multiple angles are only recorded for specific scenes.
Playback does not start
when the title is selected.
• Check the “PARENTAL” setting.
The password for rating level
has been forgotten.
• Enter the default password “4737”, then your forgotten password will be cleared.
INFORMATION
Angle does not switch.
Note:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this owner’s manual for more
details on correct operations.
• Playback from a desired track and random playback are not available during programmed playback.
• Some functions are prohibited on some discs.
39
EN
INFORMATION
5 Glossary
ATSC
HDTV (high definition TV)
Region Code
Acronym that stands for Advanced Television
Systems Committee and the name of the
digital broadcasting standards.
Ultimate digital format that produces high
resolution and high picture quality.
Aspect Ratio
Acronym that stands for National Television
Systems Committee and the name of the
current analog broadcasting standards.
Regions associate discs and players with
particular areas of the world. This unit will
only play back discs that have compatible
region codes. You can find the region code
of your unit by looking on the rear panel.
Some discs are compatible with more than
one region (or all regions).
Password
SDTV (standard definition TV)
A stored 4-digit number that allows access
to parental control features.
Standard digital format that is similar to the
NTSC picture quality.
The width of a TV screen relative to its
height. Conventional TVs are 4:3 (in
other words, the screen is almost square);
widescreen models are 16:9 (the screen is
almost twice as wide as its height).
Dolby Digital
NTSC
The system developed by Dolby Laboratories to compress digital sound. It offers
stereo sound (2ch) or multi-channel audio.
5 Maintenance
Cabinet Cleaning
• Wipe the front panel and other exterior surfaces of the unit with a soft
cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the
unit. Such chemicals may cause damage and discoloration to the exposed
surfaces.
Panel Cleaning
Wipe the panel with a soft cloth. Before cleaning the panel, disconnect the
power cord.
Servicing
Disc Handling
• Handle the discs so that fingerprints and dust do not adhere to the
surfaces of the discs.
• Always store the disc in its protective case when it is not used.
• To clean-off, use a soft cloth.
• Do not use a hard cloth since this will mar the disc.
• Wipe the disc in a straight line from center to edge.
• Never wipe with a circular motion.
Should your unit become inoperative, do not try to correct the problem
yourself. There are no user serviceable parts inside. Turn off the unit,
unplug the power cord and call our toll free customer support line found on
the cover of this manual to locate an authorized service center.
Degaussing
A degaussing circuit in this unit clears up color errors on the TV screen.
Color errors occur when there is any excess magnetism close to the unit.
This circuit is designed to operate once when the unit is first plugged
in. If you see minor color errors on the TV screen, unplug the unit for
approximately 30 minutes. When you plug the unit again, the degaussing
circuit will operate to clear errors. Take this step any time the TV screen is
accidentally magnetized or when you move the unit.
If the Laser Optical Pickup Unit is Dirty
If the unit still does not perform properly when it is operated, while referring to the relevant sections and to "Troubleshooting Guide" in this owner’s
manual, the laser optical pickup unit may be dirty. Consult your dealer
or an Authorized Service Center for inspection and cleaning of the laser
optical pickup unit.
40
EN
• Do not use detergent or abrasive cleaning agents.
IR Signal Check
If the remote control is not working properly, you can use an AM radio or
digital camera (including a cellular phone with built-in camera) to see if it
is sending out an infrared signal.
• With an AM radio:
Tune the AM radio station to a non-broadcasting
frequency. Point the remote control towards it,
push any button and listen. If the sound from the
radio flutters, it is receiving the remote control’s
infrared signal.
• With a digital camera
(including built-in cell phone
cameras):
Point a digital camera towards
the remote control. Push any
button on the remote control
and look through the digital
camera. If the infrared light appears through the
camera, the remote control is working.
INTRODUCTION
5 Cable Channel Designations
If you subscribe to cable TV, the channels are displayed as 1-135. Cable companies often designate channels with letters or letter-number combinations.
Please check with your local cable company. The following is a chart of common cable channel designations.
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
CATV channel
TV Display
2
2
J
23
W+8
44
W+29
65
W+50
86
W+66
107
W+87
128
3
3
K
24
W+9
45
W+30
66
W+51
87
W+67
108
W+88
129
4
4
L
25
W+10
46
W+31
67
W+52
88
W+68
109
W+89
130
5
5
M
26
W+11
47
W+32
68
W+53
89
W+69
110
W+90
131
6
6
N
27
W+12
48
W+33
69
W+54
90
W+70
111
W+91
132
7
7
O
28
W+13
49
W+34
70
W+55
91
W+71
112
W+92
133
8
8
P
29
W+14
50
W+35
71
W+56
92
W+72
113
W+93
134
9
9
Q
30
W+15
51
W+36
72
W+57
93
W+73
114
W+94
135
10
10
R
31
W+16
52
W+37
73
W+58
94
W+74
115
13
13
U
34
W+19
55
W+40
76
A-3
97
W+77
118
A
14
V
35
W+20
56
W+41
77
A-2
98
W+78
119
B
15
W
36
W+21
57
W+42
78
A-1
99
W+79
120
ATSC / NTSC-M TV Standard
Channel frequency synthesized tuning system
Channel access:
Direct access keyboard,
Programmable scan, and up/down
DVD
Discs (playback compatibility):
DVD video, DVD-RW/-R,
DVD+RW/+R, audio CD, CD-RW/-R
H
21
W+6
42
W+27
63
W+48
84
W+64
105
W+85
126
1W, 8Ω x 2
5 Other Specifications
Terminals:
Antenna input:
VHF/UHF/CATV
Video input:
RCA jack x 1
Audio input:
RCA jack x 2
Coaxial digital audio output:
RCA jack x 1
1
Headphone:
/8 inches (3.5mm)
Remote control:
75Ω unbalanced (F-type)
1Vp-p (75Ω)
500mV rms
500mVp-p (75Ω)
Digital encoded
infrared light system
Operating temperature:
41°F (5°C) to 104°F (40°C)
Power requirements:
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption(Maximum):
80W
Picture tube:
20 inches
Dimensions:
H
W
D
Weight:
46.2 lbs. (21.0kg)
Signal-to-noise ratio (S/N ratio):
CD:
75 dB (JEITA)
: 18.0 inches (457mm)
: 20.2 inches (512mm)
: 19.9 inches (505mm)
INFORMATION
Total distortion factor:
DVD:
1 kHz 0.07% (JEITA)
CD:
1 kHz 0.07% (JEITA)
G
20
W+5
41
W+26
62
W+47
83
W+63
104
W+84
125
TROUBLESHOOTING
Frequency response:
DVD (linear sound): 20 Hz to 20 kHz (sample rate: 48 kHz)
20 Hz to 44 kHz (sample rate: 96 kHz)
CD:
20 Hz to 20 kHz
F
19
W+4
40
W+25
61
W+46
82
W+62
103
W+83
124
DVD SETTING
Tuning system:
E
18
W+3
39
W+24
60
W+45
81
W+61
102
W+82
123
OPERATING DVD
Channel coverage (ATSC/NTSC):
Terrestrial
VHF: 2~13
UHF: 14 ~ 69
CATV:
2~13, A~W,
W+1~W+94 (analog W+1~W+84),
A-5~A-1, 5A
D
17
W+2
38
W+23
59
W+44
80
W+60
101
W+81
122
OPTIONAL SETTING
Closed caption system:
§15.122/FCC (digital CC)
§15.119/FCC (analog CC)
C
16
W+1
37
W+22
58
W+43
79
W+59
100
W+80
121
5 Electrical Specification
Sound output:
TV
TV format:
12
12
T
33
W+18
54
W+39
75
A-4
96
W+76
117
WATCHING TV
5 General Specifications
11
11
S
32
W+17
53
W+38
74
A-5
95
W+75
116
INITIAL SETTING
TV Display
CATV channel
5A
1
I
22
W+7
43
W+28
64
W+49
85
W+65
106
W+86
127
CONNECTION
CATV channel
• Designs and specifications are subject to change without notice and
without our legal obligation.
• If there is a discrepancy between languages, the default language will
be English.
41
EN
INFORMATION
42
EN
INTRODUCTION
CONNECTION
INITIAL SETTING
WATCHING TV
OPTIONAL SETTING
OPERATING DVD
DVD SETTING
TROUBLESHOOTING
INFORMATION
EN
43
LIMITED WARRANTY
This form describes the protection You will have under this Limited Warranty.
LIMITED WARRANTY PERIOD:
This Limited Warranty begins on the date of purchase of the Covered Product and continues for a period of six months.
WHAT IS COVERED:
Meijer will pay the cost of labor and repair or replacement parts in the event Your Covered Product fails to operate as a result of a mechanical or electrical
failure caused by defects in workmanship and/or materials. A mechanical or electrical failure caused by a direct result of a power surge is also covered. Parts
will be replaced with those of like kind and quality, and may be new or remanufactured. If the Covered Product cannot be repaired, if the cost of the repair
exceeds the original purchase price or if parts are not available due to the age of the Covered Product or discontinued by the manufacturer, the Covered
Product will be replaced with a product of similar features.
WHERE YOU ARE COVERED:
Coverage under this Limited Warranty is limited to the United States of America, including the District of Columbia. It does not include any Canadian or U.S.
Territories including Guam, Puerto Rico, or U.S. Virgin Islands.
WHAT IS NOT COVERED:
• PRODUCTS NOT ORIGINALLY COVERED BY A MANUFACTURER’S WARRANTY;
• ITEMS THAT ARE STILL COVERED BY THE MANUFACTURER’S WARRANTY, REGARDLESS OF WHETHER THE MANUFACTURER HONORS SUCH WARRANTY;
• PERIODIC CHECKUPS AND/OR PREVENTIVE MAINTENANCE AS DIRECTED BY THE MANUFACTURER EXCEPT AS PROVIDED HEREIN;
• INHERENT PRODUCT DEFECTS THAT ARE THE RESPONSIBILITY OF THE MANUFACTURER OR PARTS FAILURE DUE TO A MANUFACTURER’S RECALL;
• ANY AND ALL PRE-EXISTING CONDITIONS THAT OCCUR PRIOR TO THE EFFECTIVE DATE OF THIS LIMITED WARRANTY AND/OR ANY COSTS TO REPAIR ANY
PRODUCT SOLD “AS-IS” INCLUDING BUT NOT LIMITED TO FLOOR MODELS, DEMONSTRATION MODELS, ETC;
• PARTS OR REPAIRS DUE TO NORMAL WEAR AND TEAR AND ITEMS NORMALLY DESIGNED TO BE PERIODICALLY REPLACED BY THE PURCHASER DURING THE
COVERED PRODUCT’S LIFE, INCLUDING BUT NOT LIMITED TO BATTERIES, LIGHT BULBS, ETC.;
• DAMAGE FROM ACCIDENT, ABUSE, MISUSE, MISHANDLING, INTRODUCTION OF FOREIGN OBJECTS INTO THE COVERED PRODUCT, UNAUTHORIZED
MODIFICATIONS OR ALTERATIONS TO A COVERED PRODUCT, FAILURE TO FOLLOW THE MANUFACTURER’S INSTRUCTIONS, AND EXTERNAL CAUSES
INCLUDING THIRD PARTY ACTIONS, FIRE, THEFT, INSECTS, ANIMALS, EXPOSURE TO WEATHER CONDITIONS, WINDSTORM, SAND, DIRT, HAIL, EARTHQUAKE,
FLOOD, WATER, ACTS OF GOD OR CONSEQUENTIAL LOSS OF ANY NATURE;
• LOSS OR DAMAGE CAUSED BY WAR, INVASION OR ACT OF FOREIGN ENEMY, HOSTILITIES, CIVIL WAR, REBELLION, RIOT, STRIKE, LABOR DISTURBANCE,
LOCKOUT, OR CIVIL COMMOTION;
• INCIDENTAL, CONSEQUENTIAL OR SECONDARY DAMAGES OR DELAY IN RENDERING SERVICE UNDER THIS LIMITED WARRANTY, OR LOSS OF USE DURING
THE PERIOD THAT THE COVERED PRODUCT IS AT AN AUTHORIZED SERVICE CENTER OR OTHERWISE AWAITING PARTS;
• ANY PRODUCT USED IN A COMMERCIAL SETTING OR RENTAL BASIS;
• FAILURES THAT OCCUR OUTSIDE OF THE 50 STATES OF THE UNITED STATES OF AMERICA, INCLUDING THE DISTRICT OF COLUMBIA;
• NONFUNCTIONAL OR AESTHETIC PARTS INCLUDING BUT NOT LIMITED TO PLASTIC PARTS, KNOBS, ROLLERS, BASKETS, SCRATCHES, PEELING AND DENTS;
• UNAUTHORIZED REPAIRS AND/OR PARTS;
• COST OF INSTALLATION, SET-UP, DIAGNOSTIC CHARGES, REMOVAL OR REINSTALLATION OF THE COVERED PRODUCT, EXCEPT AS PROVIDED HEREIN;
• ACCESSORIES USED IN CONJUNCTION WITH A COVERED PRODUCT;
• ANY LOSS OTHER THAN A COVERED BREAKDOWN OF THE COVERED PRODUCT;
• SERVICE WHERE NO PROBLEM CAN BE FOUND;
• BREAKDOWNS WHICH ARE NOT REPORTED WITHIN THE TERM OF THIS LIMITED WARRANTY;
• IMPROPER INSTALLATION OF COMPONENTS OR PERIPHERALS;
• CORRUPTION OF ANY RECORDING MEDIA, INCLUDING ANY PROGRAM, DATA OR SETUP INFORMATION RESIDENT ON ANY HARD DRIVES AND INTERNAL
OR EXTERNAL REMOVABLE STORAGE DEVICES, AS A RESULT OF THE MALFUNCTIONING OR DAMAGE OF AN OPERATING PART, OR AS A RESULT OF ANY
REPAIRS OR REPLACEMENT UNDER THIS LIMITED WARRANTY;
• DAMAGE TO CLOTHING;
• COLOR FADING OF PICTURE FOR ANY TELEVISION;
• BURNED-IN PHOSPHOR (INCLUDING IMAGE GHOSTING), PIXEL BURNOUT NOT IN ACCORDANCE WITH THE MANUFACTURER’S SPECIFICATIONS.
WHAT TO DO WHEN YOUR PRODUCT FAILS TO OPERATE:
• Call the 24-hour customer service toll-free number at (866) 845-9436.
Many oversights, which are not covered under this Limited Warranty, can be due to simple circumstances such as the Covered Product not being switched
on, being unplugged, or a fuse blown at the junction box. For a Covered Product that uses batteries as the primary power supply, or a remote control unit,
please check that the batteries do not need replacing or recharging.
SERVICE DELIVERABLES:
There is no deductible required to obtain service for Your Covered Product.
OTHER PROVISIONS:
Limit of Liability:
The limit of liability under this Limited Warranty is the least of the cost of (1) the purchase price of the Covered Product excluding tax and delivery costs or (2)
authorized repairs not to exceed the purchase price of the Covered Product or (3) replacement of the Covered Product with similar features or (4) reimbursement
for authorized repairs or replacement. Upon replacement, there is no longer any obligation for the replaced product under this Limited Warranty.
Limitations of Implied Warranty:
All Implied Warranties which may arise under state law, including all Implied Warranties of Merchantability or Fitness for a particular purpose, are limited to
the duration of this Warranty and do not cover incidental or consequential damages. Some states do not allow limitations on how long an Implied Warranty
lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to You. This Warranty gives You specific
legal rights, and You may also have other rights which vary from state to state.
Transferability and Renewals:
This Limited Warranty is not transferable or renewable.
Subrogation:
If We pay for a loss, We may require You to assign Us Your rights of recovery against others. We will not pay for a loss if You impair these rights to recover. Your
rights to recover from others may not be waived.
Arbitration:
In the event of a disagreement between You and Us concerning costs, either of us may make a written demand for arbitration. This must be done within
sixty (60) days after the day You filed Your claim. Each of us will select an arbitrator. The two arbitrators will select an umpire. Each of us will pay the expenses
of the arbitrator We select. The expenses of the umpire will be shared equally. Unless both of us agree otherwise, arbitration will take place in the county and
state in which You live. Local rules apply. A majority decision will be binding.
Dist. by Wholesale Merchandisers, Inc., 2929 Walker, N.W., Grand Rapids, MI 49544
Printed in Thailand
P7454UT
1EMN22501 *****
Download PDF

advertising