Furuno 1724C Marine GPS System User Manual

4-659-932-11(1)
Chapter 1
What is the Sony
CLIÉ Handheld?
Chapter 2
Setting up your Sony
CLIÉ Handheld
– Basics
Chapter 3
Read
This
First
Personal Entertainment Organizer
PEG-T615C/PEG-T415
© 2001 Sony Corporation
Setting up your Sony
CLIÉ Handheld
– Advanced
WARNING
To prevent fire or shock hazard, do
not expose the unit to rain or
moisture. To avoid electrical shock,
do not open the cabinet. Refer
servicing to qualified personnel
only.
For customers in the U.S.A and
Canada
Owner’s Record
The model number and serial number are
located at the rear of the product. Record the
model number and the serial number in the
space provided below. Refer to them
whenever you call upon your Sony dealer
regarding this product.
Model No._____________
Serial No.______________
The socket-outlet shall be installed near the
equipment and shall be easily accessible.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numerique de la classe B est
conforme a la norme NMB-003 du Canada.
NOTE
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
2
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
rotating the equipment off and on, the user
is encouraged to try to correct the
interference using one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
If you have a question about this product,
call the Sony Customer Information Center
at keep on next line 1-877-760-7669; or write
to the Sony Customer Information Center at
12451 Gateway Boulevard, Fort Myers, FL
33913. The number below is for FCC-related
matters only.
Declaration of Conformity
Trade Name: SONY
Model No.: PEG-T615C
PEG-T415
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road,
Oradell, NJ 07649 USA
Telephone No.: 201-930-6972
This device complies with part 15 of the
FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any
interference received, including
interference that may cause
undesired operation.
The supplied interface cable must be used
with the equipment in order to comply with
the limits for a digital device pursuant to
Subpart B of Part 15 of FCC Rules.
On the supplied software
• Copyright laws prohibit reproducing
the software or the software manual in
whole or in part, or renting the software
without the permission of the copyright
holder.
• In no event will SONY be liable for any
financial damage or loss of profits,
including claims made by third parties,
arising out of the use of the software
supplied with this player.
• In the event a problem occurs with this
software as a result of defective
manufacturing, SONY will replace it at
SONY’s option or issue a refund.
However, SONY bears no other
responsibility.
• The software provided with this
product cannot be used with equipment
other than that which it is designated
for use with.
• Please note that, due to continued
efforts to improve quality, the software
specifications may be changed without
notice.
Program © 2001 Sony Corporation, © 2001
Palm, Inc. or its subsidiaries. All rights
reserved.
Documentation © 2001 Sony Corporation
CAUTION
Please contact your nearest Sony dealer
regarding the problem you are experiencing
with your Sony product.
Notes
• Sony does not support third-party addon applications. If you are having a
problem with a third-party application,
please contact the developer or
publisher of that software.
• The illustrations in this manual may
differ from the actual software.
• Explanations in this manual assume that
you are familiar with basic operations of
Windows®. For how to use your
computer and operating system, please
refer to their respective manuals.
Sony, Memory Stick, the Memory Stick logo,
Jog Dial, and PictureGear are trademarks of
Sony Corporation.
Graffiti, HotSync, and Palm OS are
registered trademarks, and the HotSync logo
and Palm are trademarks of Palm, Inc. or its
subsidiaries.
IBM and PC/AT are registered trademarks
of International Business Machines
Corporation.
Microsoft, Windows, Windows NT,
Outlook, DirectX and the Windows 98 logo
are registered trademarks of Microsoft
Corporation.
MMX and Pentium are registered
trademarks of Intel Corporation.
AvantGo, the AvantGo Client and the
AvantGo logo are registered trademarks of
AvantGo, Inc.
Pumatech, the Pumatech logo, Intellisync
and Intellisync Lite are trademarks of
Pumatech, Inc. that may be registered in
some jurisdictions.
Adobe and Adobe Acrobat Reader are
trademarks of Adobe Systems Incorporated.
QuickTime and the QuickTime logo are
trademarks used under license. QuickTime
is registered in the U.S. and other countries.
This product includes fonts owned by
TypeBank Co., Ltd. under license.
All other trademarks are trademarks of their
respective owners.
Sample movies and music: cocoro.prc
(from DVD Hawaiian Breeze - KOHALA
Collection (CCBN-27013))
Music: Mango Cooler (Composed by
Charles Michael Brotman. Performed by
KOHALA)
Copyright © 2001 cocoronetworks, inc.
Copyright © 1998, 2001 Palm Records, Inc.
All rights reserved.
http://www.cocoronet.com/en/
Before using your CLIÉ handheld, be sure to
read the accompanying End-User’s License
Agreement.
3
Table of Contents
About this manual ........................... 5
Which manual to read? .................... 7
Chapter 1
What is the Sony CLIÉ Handheld?
What can you do with your Sony
CLIÉ Handheld? .............................. 10
System requirements ..................... 11
Sony CLIÉ Handheld components .. 12
Locating front panel controls ........... 12
Locating back panel components .... 14
Locating cradle components ............ 17
Elements of the CLIÉ interface ......... 18
What is on the CLIÉ Installation
CD-ROM? ........................................ 20
CD-ROM contents ............................ 20
How to read the PDF manuals on
the CD-ROM .................................... 21
Chapter 2
Setting up your Sony CLIÉ
Handheld – Basics
Step 1: Charging your Sony CLIÉ
Handheld .................................... 24
Step 2: Turning on your Sony CLIÉ
Handheld for the first time ........ 25
Step 3: Entering data into your
Sony CLIÉ Handheld ................... 29
Step 4: Installing the Palm™ Desktop
for CLIÉ software on your
computer .................................... 31
Step 5: Connecting your Sony CLIÉ
Handheld and your computer via
the cradle ................................... 35
Step 6: Performing a HotSync®
operation for the first time ........ 36
4
Chapter 3
Setting up your Sony CLIÉ
Handheld – Advanced
Checking the bundled applications
on your Sony CLIÉ Handheld .......... 40
Overview of basic Palm OS®
applications ..................................... 41
Overview of Sony applications ......... 44
Installing the supplied applications
on your computer .......................... 48
Installing PictureGear™ 4.4Lite ....... 48
Installing QuickTime® 5 .................. 48
Installing DirectX® 6 ....................... 49
Installing Memory Stick Export ........ 49
Installing Sound Converter .............. 50
Installing AvantGo® and other thirdparty applications ............................ 50
Installing Acrobat Reader® 5.0 ........ 51
Uninstalling the supplied
applications ..................................... 52
Installing add-on applications on
your Sony CLIÉ Handheld or
Memory Stick media ...................... 53
Installing add-on applications
from the Palm™ Desktop for
CLIÉ software ................................... 54
Installing add-on applications by
beaming them from another
Palm OS® device ............................. 57
Installing add-on applications
directly from the Installation
CD-ROM menu ................................ 59
Removing add-on applications ........ 60
Customer registration .................... 61
About this manual
Welcome to the Sony Personal Entertainment Organizer (referred to as
the “CLIÉ handheld” or “Sony CLIÉ Handheld” in this manual).
Your CLIÉ handheld comes with three manuals:
■ Read This First (this guide)
■ Operating Instructions (as a PDF file contained in the CD-ROM)
■ Add-on Application Guide
Before using your CLIÉ handheld, read this guide for an overview of
features, setup and installation instructions, and other important
details.
After you set up your CLIÉ handheld and become familiar with its
basic functions, you can use the other two manuals (Operating
Instructions and Add-on Application Guide) as references for detailed
features, less common tasks, and maintenance of your CLIÉ handheld.
These manuals can also serve as a source of information if you have
problems operating your CLIÉ handheld.
The contents of the three manuals are as follows.
Read This First (this guide)
This guide is designed to help you quickly get your CLIÉ handheld up
and running.
This guide shows you how to:
■ Identify all the parts of your CLIÉ handheld
■ Set up your CLIÉ handheld
■ Install supplied applications on your CLIÉ handheld and your
computer
■ View and enter data
Continued on next page
5
About this manual
Operating Instructions
The Operating Instructions manual is contained in the supplied CDROM as a PDF file; you can view or print the file as necessary.
The manual describes how to use your CLIÉ handheld and the
Personal Information Management (PIM) applications that come with
your CLIÉ handheld.
Additionally, the manual shows you how to:
■ View and enter data in greater detail
■ Use your CLIÉ handheld with your computer
■ Use Personal Information Management applications (Date Book,
Address Book, To Do List, Memo Pad, and Calculator)
■ Personalize your CLIÉ handheld with your own preference settings
■ Maintain your CLIÉ handheld
Add-on Application Guide
The Add-on Application Guide describes how to install and use the
supplied add-on applications, including:
■ PictureGear™ Pocket/PhotoStand/CLIÉ Paint/PictureGear 4.4Lite
■ gMovie™
■ World Alarm Clock
■ CLIÉ Remote Commander
■ Sound Utility/Sound Converter
■ MS Autorun
■ MS Import/Export
The three manuals all describe operations of two models of the CLIÉ
handheld (PEG-T615C and PEG-T415). All illustrations of the unit are
of PEG-T415, unless specified otherwise. Points of difference between
the two models are described in their relative sections.
6
Which manual to read?
After you set up your CLIÉ handheld and become familiar with its
basic functions, you can refer to the rest of the manuals as follows:
When you want to:
Read:
Manage your personal
information using your
CLIÉ applications.
Operating Instructions
Chapter 2
Using basic applications
Use your CLIÉ handheld
and your computer in
synchronization.
Operating Instructions
Chapter 3
Exchanging and updating data
using a HotSync® operation
Exchange and share
information with other
handheld users.
Operating Instructions
Chapter 4
Communicating using your
Sony CLIÉ Handheld
Enjoy viewing images on
your CLIÉ handheld.
Add-on Application Guide
Chapter 1
Viewing image files
(PictureGear Pocket)
Enjoy drawing on image
files on your CLIÉ
handheld.
Add-on Application Guide
Chapter 2
Drawing on image files (CLIÉ Paint)
Enjoy watching movies on
your CLIÉ handheld.
Add-on Application Guide
Chapter 3
Playing a movie (gMovie player)
View the World Alarm
Clock on your CLIÉ
handheld.
Add-on Application Guide
Chapter 4
Viewing the World Alarm Clock
(World Alarm Clock)
Use your CLIÉ handheld as
a remote commander.
Add-on Application Guide
Chapter 5
Using your CLIÉ handheld as a
remote commander
(CLIÉ Remote Commander)
Import your favorite
sound from your computer
to your CLIÉ handheld.
Add-on Application Guide
Chapter 6
Importing your favorite sounds
(Sound Utility/Sound Converter)
7
Chapter 1
Chapter 1
What is the Sony CLIÉ Handheld?
This chapter describes the features of your CLIÉ handheld, its
system requirements, its buttons and controls, and the
contents of the Installation CD-ROM.
Contents
What can you do with your Sony CLIÉ Handheld? ..................... 10
System requirements ................................................................. 11
Sony CLIÉ Handheld components ..............................................
Locating front panel controls ...............................................
Locating back panel components .........................................
Locating cradle components ................................................
Elements of the CLIÉ interface .............................................
12
12
14
17
18
What is on the CLIÉ Installation CD-ROM? ............................... 20
CD-ROM contents ............................................................... 20
How to read the PDF manuals on the CD-ROM .................... 21
What can you do with your Sony CLIÉ Handheld?
Your CLIÉ handheld can help you remember appointments and
meeting times, people’s names and personal details, and items on your
To Do List. Your CLIÉ handheld can also help you improve your track
record in all these areas, both at work and at home.
Once you familiarize yourself with the basic workings of your CLIÉ
handheld, you’ll easily be able to:
■ Enter all your schedule details in the Date Book and view them by
the day, week, or month, and even set an alarm to remind you of an
important event.
■ Keep all your contact names, addresses, phone numbers, and other
details in the Address Book. In addition, you can paste an image to
an address record using the supplied PictureGear™ Pocket
application.
■ Add your tasks to the To Do List, prioritize them, and assign them
a due date.
■ Synchronize your data with the Palm™ Desktop for CLIÉ software
on your computer so you always have a backup copy of your
important information.
■ Customize your CLIÉ handheld and set different levels of security
to prevent unauthorized users from viewing your data.
■ Exchange data with your computer, other Sony CLIÉ handhelds,
digital cameras, or other portable devices with Sony’s Memory
Stick™ media.
■ Play back image files with the PictureGear™ Pocket application on
your CLIÉ handheld or with the PictureGear™ Lite software on
your computer.
■ Watch a movie with the gMovie™ application on your CLIÉ
handheld.
■ Use other add-on applications for the Palm OS®.
■ Enjoy Web Clipping*.
* Web Clipping is a system provided by Palm, Inc. and its subsidiaries for
Palm OS handhelds, which enables easy access to information provided on
the Web. If you install various Web Clipping applications on your CLIÉ
handheld, you can retrieve specific information such as news, weather, or
restaurant guides to display them on your CLIÉ handheld. Web clipping
applications require Internet connections. For details on its use, or for
answers to your questions, refer to the following homepage:
http://www.palm.com/wireless/
10
System requirements
■ OS: Microsoft® Windows® 98/Windows® 98 Second Edition/
Windows® 2000 Professional/Windows® Millennium Edition/
Windows® XP
■ CPU: Pentium® processor 133MHz or more
■ RAM: 32MB or more (64MB or more recommended)
■ Hard disk drive: 128MB or more available space
■ Display: High Color or more (800 × 600 pixels or more)
■ CD-ROM drive
■ Mouse or similar pointing device
■ One available USB connector
Notes
• To install the Palm Desktop for CLIÉ software on Windows® 2000 Professional,
log on as “Administrator.”
• Macintosh computers are not compatible with the Sony CLIÉ Handheld.
11
Chapter 1 What is the Sony CLIÉ Handheld?
To install and operate the Palm™ Desktop software on your computer,
your computer system must meet the following requirements:
Sony CLIÉ Handheld components
Locating front panel controls
1 Jog Dial™ Navigator
Used to select and run applications or items. Depending on the
application you use, specific functions are assigned to the navigator.
For details, see “Using the Jog Dial™ navigator” in the Operating
Instructions manual.
2 BACK Button
Releases the selection of an item or cancels the operation.
Depending on the application you use, returning to the previous
screen or other specific functions are assigned to this button.
3 Scroll Button
Displays text and other information that extends beyond the area of
the screen. Pushing the scroll button downwards scrolls down to
display information below the current viewing area, and pushing
up the button scrolls up to display the information above the
current viewing area. Depending on the application you use,
specific functions are assigned to the scroll button.
12
Activates the individual applications that correspond to the icons on
the buttons:
Date Book,
Address Book,
To Do List, and
Memo Pad. See “Assigning applications to buttons” in the
Operating Instructions manual for details on reassigning these
buttons to activate any application on your CLIÉ handheld.
5 Screen
Displays the applications and information stored in your CLIÉ
handheld. It is touch-sensitive and responds to the stylus. For
details, see “Elements of the CLIÉ interface” on page 18.
6 Graffiti Writing Area
The area where you write letters and numbers using the Graffiti®
alphabet. See “Using Graffiti® writing to enter data” in the
Operating Instructions manual to learn how to write Graffiti
characters.
7 POWER Button
Used to turn your CLIÉ handheld on or off. Also, press the POWER
button and hold it down for two seconds or longer to turn the
backlight of the LCD display on or off.
Tip
If your CLIÉ handheld is turned off, pressing any application button
activates your CLIÉ handheld and opens the corresponding application.
8 LED indicator
Flashes to notify you at a given time if you set an alarm in Date
Book or the World Alarm Clock application. Also lights while
charging the battery, and turns off when charging is complete.
13
Chapter 1 What is the Sony CLIÉ Handheld?
4 Application Buttons
Sony CLIÉ Handheld components
Locating back panel components
1 Stylus
Used to tap icons and buttons on the screen, or to write characters
on the Graffiti writing area.
For details, see “Using the stylus” in the Operating Instructions
manual.
2 Memory Stick™ Slot
Insert Memory Stick media into this slot.
3 Memory Stick Access Indicator
Lights in orange while your CLIÉ handheld is reading/writing the
data in Memory Stick media.
4 Infrared Communication Port (IR port)
Uses infrared technology to:
- transmit data to and receive data from other CLIÉ or Palm OS®
handhelds, and to perform HotSync® operations.
For details, see “Beaming between your Sony CLIÉ Handheld
and another Palm OS® PDA” in the Operating Instructions
manual.
14
5 Reset Button
Under normal use, you should not have to use this button.
For details, see “Resetting your Sony CLIÉ Handheld” in the
Operating Instructions manual.
6 Interface Connector
Used to connect your CLIÉ handheld to the cradle or to the
accessories for the CLIÉ handheld (not supplied).
15
Chapter 1 What is the Sony CLIÉ Handheld?
- remote-control devices with the CLIÉ Remote Commander
application. For details, see chapter 4 in the Add-on Application
Guide.
Sony CLIÉ Handheld components
Removing the supplied protective soft cover from your CLIÉ
handheld
Slide both switches on the attached end of the cover towards the center
(1), then remove the cover (2).
Reattaching the protective soft cover
Slide the switches towards the center (1) and place the tabs into the
holes of the CLIÉ handheld (2). Then slide the switches outwards
until they lock into place.
16
Chapter 1 What is the Sony CLIÉ Handheld?
Locating cradle components
1 AC Adapter Connector
Connect the supplied AC adapter here.
2 Interface Connector
Connect your CLIÉ handheld here.
3 Cradle Indicator
When you connect the cradle to the AC adapter and place your
CLIÉ handheld on the cradle, the green indicator lights and
charging starts.
4 HotSync®
Button
Synchronizes data in your CLIÉ handheld with the data saved on
your computer.
For details, see “Exchanging and updating data using a HotSync®
operation” in the Operating Instructions manual.
5 USB Connector
Connects to your computer’s USB port.
17
Sony CLIÉ Handheld components
Elements of the CLIÉ interface
1 Battery Icon
Displays the remaining charge in the battery. While your CLIÉ
handheld is placed in the cradle or operates on the AC power
source, the battery charging icon (
) is displayed. Tapping the
icon shows the amount of the battery’s remaining charge by
percentage, and free memory space.
2 Home Icon
Tap this icon and the Application Launcher screen appears,
displaying a list of applications.
3 Menu Icon
Tap this icon and a menu of current applications appears.
4 Brightness/Contrast Adjustment Icon
Tap this icon to display the window used for adjusting the
brightness level (PEG-T615C) or the contrast level (PEG-T415) of the
LCD screen of your CLIÉ handheld.
18
5 Application Icon
Tap an icon to activate the corresponding application.
6 Scroll Bar
Drag the slider up or down or tap the scroll arrows v or V on the
ends of the bar to scroll the screen.
7 Calculator Icon
Tap this icon to display the onscreen Calculator.
8 Find Icon
Tap this icon to open the Find screen.
9 Graffiti Writing Area
This area is for hand-writing input with the Graffiti alphabet.
Tip
When the tip i icon is displayed, you can tap the icon to display online
operational tips on the screen.
Tip i icon
Note on display resolutions
Your CLIÉ handheld uses original technology to provide a 320 × 320
dot high resolution display. When you start an application supporting
the high resolution, the screen switches automatically to the high
resolution mode. When you start an application that does not support
high resolution, the screen returns to the standard 160 × 160 dot
resolution mode.
Note
In some third-party applications, the screen may not be displayed properly.
19
Chapter 1 What is the Sony CLIÉ Handheld?
Note
If the digitizer preferences are not set correctly, you cannot adjust the
brightness/contrast level properly. For details, see “Adjusting the screen” in
the Operating Instructions manual.
What is on the CLIÉ Installation CD-ROM?
CD-ROM contents
The Installation CD-ROM that comes with your CLIÉ handheld
contains the following applications and manuals:
■ PC applications
You can install the following PC applications and related online
help files from the installer’s main launcher window:
– Palm Desktop for CLIÉ 4.0.1
(including Intellisync Lite 4.0)
– PictureGear™ 4.4Lite
– QuickTime® 5
– DirectX® 6
– Memory Stick™ Export
– Sound Converter
The following PC application has a separate installer package:
– Adobe Acrobat Reader® 5.0
■ Palm OS applications
You can install the following Palm OS® applications on your CLIÉ
handheld:
– CLIÉ Paint
– World Alarm Clock
– CLIÉ Remote Commander
– Sound Utility
The following sample data and demonstration files are also
available:
– CLIÉ Demo
– Sample data for gMovie and PictureGear Pocket
– Sample sound data
20
The following manuals are available as PDF files on the CD-ROM:
– Read This First (this guide)
– Operating Instructions
– Add-on Application Guide
– PictureGear Pocket Manual
– CLIÉ Paint Manual
– gMovie Manual
– World Alarm Clock Manual
– CLIÉ Remote Commander Manual
– MS Gate Manual
– MSAutorun Manual
– MS Import Export Manual
– IntelliSync Lite Manual
Tip
You can view the manuals by clicking Manuals in the installation launcher
window that appears when you insert the CLIÉ Installation CD-ROM into your
computer.
How to read the PDF manuals on the CD-ROM
To view the PDF manuals contained on the Installation CD-ROM, you
need the Acrobat Reader software installed on your computer. To
install the Acrobat Reader software, see “Installing Acrobat Reader®
5.0” on page 51.
To open a PDF manual, do either of the following:
• Double-click a PDF file on the CD-ROM.
The Acrobat Reader software starts and the selected PDF manual is
displayed. You can read and print the file.
• Start the Acrobat Reader software and select Open from the File
menu. In the Open dialog box, select a PDF file and click Open.
The selected PDF manual is displayed. You can read and print the
file.
21
Chapter 1 What is the Sony CLIÉ Handheld?
■ Manuals
Chapter 2
This chapter describes basic hardware setup procedures that
you should perform, before you start using your CLIÉ
handheld in combination with your computer. These
procedures include: charging your CLIÉ handheld with the
cradle, synchronizing data with your computer, and entering
data.
Contents
Step 1: Charging your Sony CLIÉ Handheld ............................... 24
Step 2: Turning on your Sony CLIÉ Handheld for the first time .. 25
Step 3: Entering data into your Sony CLIÉ Handheld ................. 29
Step 4: Installing the Palm™ Desktop for CLIÉ software
on your computer .............................................................. 31
Step 5: Connecting your Sony CLIÉ Handheld and
your computer via the cradle ............................................ 35
Step 6: Performing a HotSync® operation for the first time ...... 36
Chapter 2
Setting up your Sony CLIÉ Handheld – Basics
Step 1: Charging your Sony CLIÉ Handheld
Note
Before you use your CLIÉ handheld for the first time, make sure to charge it.
Connect the supplied cradle to an AC power source in advance.
Charging will start as soon as you place your CLIÉ handheld on the
cradle. The battery icon in the screen changes to the battery charging
icon (
).
It takes about four hours for your CLIÉ handheld to be fully charged
for the first time. Subsequent charges, if your CLIÉ handheld is
charged frequently, will require less time.
To the wall
outlet
Insert your CLIÉ handheld at an
angle to the cradle and lay it
back to fit into place.
When you place your CLIÉ handheld on the cradle, the cradle
indicator and the LED indicator of your CLIÉ handheld turns on, and
charging starts.
When charging is completed
The LED indicator of your CLIÉ handheld turns off. When you remove
your CLIÉ handheld from the cradle, the battery charging icon changes
to the battery icon (
).
The cradle indicator remains on even after charging is completed.
Note
If the battery in your CLIÉ handheld is fully discharged, all data stored on
the DRAM (memory) is lost. Performing another HotSync® operation once the
battery is recharged can restore information saved from the last HotSync
operation.
24
Step 2: Turning on your Sony CLIÉ
Handheld for the first time
The first time you start your CLIÉ handheld, setup instructions appear
onscreen. Follow the onscreen instructions to perform initial settings,
digitizer calibration, current time, date, and year settings (required for
operation).
Press the POWER button.
Your CLIÉ handheld turns on, and the Welcome screen appears.
After a while, the Setup screen appears.
b
Press the POWER button.
2
Take out the Stylus.
You can use the stylus to tap or drag on the screen to open
applications, choose options or menu commands, and select text or
move objects just as you do with a mouse on your computer.
Note
Always use the point of the stylus for tapping or making strokes on the
handheld screen. Never use a real pen, pencil, or other sharp object to write
on the screen.
Continued on next page
25
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
1
Step 2: Turning on your Sony CLIÉ Handheld for the first time
3
Press lightly on the screen with the stylus.
This action is called “tapping.”
The digitizer calibration screen appears. Calibration aligns the
internal circuitry of the handheld with its touch-sensitive screen so
your CLIÉ handheld can detect the task you want to perform when
you tap an element on the screen.
4
Tap anywhere on the screen.
The following screen is displayed.
5
Following the onscreen instruction, tap the center of the
displayed mark.
Note
If the digitizer is not configured correctly, the scroll bar may not operate
properly, “tapping” may not work as expected, or other problems may
occur. If this happens, please re-configure the digitizer manually. You can
also re-configure the digitizer in the Digitizer Preferences screen. For details,
see “What you can do with Preferences” in the Operating Instructions
manual.
26
After calibration completes, a screen for setting time and date
appears.
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
6
Tap the Set Date box.
The Set Date screen appears.
7
Tap the arrow b or B next to the year to select the
current year.
8
Tap the current month, then tap the current date.
The Set Date screen closes.
9
Tap the Set Time box.
The Set Time screen appears.
10 Tap the arrow v or V to set the hour to the current time.
Continued on next page
27
Step 2: Turning on your Sony CLIÉ Handheld for the first time
11 Tap each number of the minute, and then tap the arrow
v or V to set the minutes to the current time.
12 Tap AM or PM.
13 Tap OK.
The Set Time screen closes.
14 Tap Next.
The Setup Complete screen appears.
15 Tap Next.
The Enter Data screen appears.
16 Tap Done.
The initial settings are complete, and the Application Launcher
screen (Home screen) appears.
Your CLIÉ handheld is now ready for use!
28
Step 3: Entering data into your Sony CLIÉ
Handheld
There are three ways to enter data into your CLIÉ handheld:
– Using Graffiti® writing
– Using the onscreen keyboard
– Using your computer keyboard
Your CLIÉ handheld includes Graffiti writing application as the
primary system for entering text and numbers. With Graffiti writing,
you write simple strokes with the stylus and they are instantly
recognized as letters or numbers.
The Graffiti strokes closely resemble the upper case letters of the
regular alphabet, which makes Graffiti writing easy to learn.
Graffiti writing examples:
A, B, C, D, and E
The Graffiti writing area is divided into two parts: one for writing the
letters of the alphabet and one for writing numbers. The small marks at
the top and bottom of the Graffiti writing area indicate the two areas.
Write letters
here
Write numbers here
Division marks
For details, see “Using Graffiti® writing to enter data” in the Operating
Instructions manual.
Onscreen keyboard
When you use an application such as Date Book or Address Book, you
can open the onscreen alphabetic and numeric keyboards to enter data.
Tap here for
alphabetic keyboard
Tap here for numeric
keyboard
Continued on next page
29
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
Graffiti writing
Step 3: Entering data into your Sony CLIÉ Handheld
After a keyboard is open, you can tap to open any of the other
keyboards, including the international keyboard. For details, see
“Using the onscreen keyboard” in the Operating Instructions manual.
Alphabetic
Tab
Backspace
Caps lock
Caps shift
Carriage return
Tap here to display alphabetic keyboard
Numeric
Tap here to display numeric
keyboard
International
Tap here to display international
keyboard
Computer keyboard
If you have a lot of data to enter, or prefer to use the computer
keyboard, you can use the Palm™ Desktop for CLIÉ software or any
supported PIM (Personal Information Management) applications to
enter information. You can then perform a HotSync® operation to
synchronize the information on your computer with the information
on your CLIÉ handheld. All the main applications on your CLIÉ
handheld are also available in the Palm Desktop for CLIÉ software and
in most PIM applications, so you don't need to learn different
applications.
Refer to the Palm Desktop for CLIÉ online Help for more information
on entering data using your computer.
30
Step 4: Installing the Palm™ Desktop for
CLIÉ software on your computer
Notes
• Do not connect the cradle to a USB connector of your computer before
installing the Palm Desktop for CLIÉ software. The installation of the software
might not be performed correctly.
• If you are already using a Sony CLIÉ Handheld (PEG-S300/S320/N610C/
N710C) or other Palm™ OS PDA device, and Palm Desktop software is
installed on your computer: uninstall it and reinstall the Palm Desktop for
CLIÉ software using the supplied Installation CD-ROM. For details, see
“Upgrading the existing Palm Desktop software” on page 34.
• The Palm Desktop for CLIÉ software supplied to this CLIÉ handheld
(PEG-T615C/T415) does not support Expense.
• Do not simply copy the Palm Desktop for CLIÉ software files to your
computer’s hard disk. You must use the installer and follow the procedures
described in this section to place the files in their proper locations and to
decompress the files.
• To introduce the CLIÉ data of your old CLIÉ handheld into the new one, see
“Using data of another Sony CLIÉ Handheld” in the Operating Instructions
manual.
1
Exit all applications running on Windows®.
You should quit all applications that automatically run at startup,
such as fax communication software, anti-virus tools, screensavers,
and the Microsoft® Office Shortcut Bar.
2
Insert the Installation CD-ROM into the CD-ROM drive of
your computer.
The installation launcher window appears.
3
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
Continued on next page
31
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
The Palm™ Desktop for CLIÉ software extends many of the functions
of your CLIÉ handheld to your computer, featuring the same main
applications as those on your CLIÉ handheld: Address Book, Date
Book, To Do List, Memo Pad, and desktop e-mail connectivity. You can
use the HotSync® Manager feature of this software to back up and
exchange data between your CLIÉ handheld and your computer.
Step 4: Installing the Palm™ Desktop for CLIÉ software
on your computer
4
Click Install Palm Desktop for CLIÉ.
The setup program starts and the Welcome screen is displayed.
5
Click Next.
The Palm Desktop for CLIÉ 4.0.1 software installation begins.
Follow the onscreen instructions, then the following dialog box
appears.
6
Select the software you will use to synchronize your CLIÉ
handheld with your computer.
If you select “Synchronize with Palm Desktop for CLIÉ,” Intellisync
Lite will not be installed. If you select “Synchronize with Microsoft
Outlook or Lotus Organizer,” Palm Desktop and Intellisync Lite
will be installed.
32
7
Click Next.
The Setup Type window is displayed.
Select the setup type (Typical or Custom) and the
destination folder.
If you wish to synchronize PEG-S300 or PEG-N710C with your
CLIÉ handheld (PEG-T615C/T415), follow the steps below:
1 Select Custom for the setup type and click Next.
2 On the select components screen, make sure that USB Switcher
is selected. For Windows® XP users, visit
http://www.sony.com/peg/support
for the latest driver information.
3 Follow the onscreen instructions until setup is complete.
When you follow the onscreen instructions, the Create User
Account screen is displayed.
9 Fill in the user name in the Create User Account screen.
10 Click Next.
The Install Tool dialog box closes, then the Mail Setup dialog box
appears.
11 Set up Mail.
Follow the onscreen instructions until Mail setup is complete.
Continued on next page
33
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
8
Step 4: Installing the Palm™ Desktop for CLIÉ software
on your computer
12 Fill in the customer registration following the
instructions shown onscreen.
You need Internet access for the online customer registration.
You can take advantage of Sony’s commitment to quality customer
support and nine months of the extended limited warranty for a
total of 12 months from the original date of purchase when you
register your CLIÉ handheld.
13 Click Finish.
Note
Make sure you perform a HotSync operation before installing any thirdparty applications. (See pages 35 - 37)
Upgrading the existing Palm Desktop software
Multiple versions of Palm Desktop software cannot be installed on one
computer. If an older version of Palm Desktop for CLIÉ software
already exists, it is recommended that you uninstall it prior to the new
installation. All handheld user data is preserved when upgrading the
Palm Desktop for CLIÉ software.
On Intellisync Lite
The Intellisync Lite software allows you to synchronize your Date
Book, Address Book, To Do List, and Memo Pad data in your CLIÉ
handheld with the data of a variety of popular Windows® applications
including:
– Microsoft Outlook 97/98/2000/2002
– Lotus Organizer 5.0/6.0
During a HotSync operation, the Intellisync Lite software compares
each record of information in your CLIÉ handheld to the information
stored in the PIM (Personal Information Management) applications,
and then makes necessary changes to both systems to make sure that
they both contain the same data.
34
Step 5: Connecting your Sony CLIÉ Handheld
and your computer via the cradle
The cradle that comes with your CLIÉ handheld enables you to
synchronize the information on your CLIÉ handheld with the Palm™
Desktop for CLIÉ software on your computer using HotSync®
technology.
Connect the USB connector of the cradle to a USB
connector on your computer.
To the wall outlet
2
Place your CLIÉ handheld on the cradle.
Insert your CLIÉ handheld at an angle to the
cradle and lay it back to fit it into place.
35
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
1
Step 6: Performing a HotSync® operation
for the first time
What is a HotSync operation?
HotSync, which is a technology particular to a Palm OS® platform
device, is the one-step operation that allows you to synchronize data
between your CLIÉ handheld and your computer, and back up the
CLIÉ data on your computer. For details, see “Exchanging and
updating data using a HotSync® operation” in the Operating
Instructions manual.
When performing a HotSync® operation for the first time, you have to
enter your user information both into your CLIÉ handheld and into the
Palm Desktop for CLIÉ software. After the user name is recognized,
you do not have to enter the same information again.
1
Press the HotSync
button on the cradle.
Press the HotSync button.
The USB Driver Installation Wizard starts automatically.
2
When the New User dialog box is displayed on your
computer screen, select the user name.
Select the same user name you entered in step 8 on page 33.
Note
Every handheld should have a unique name. To prevent loss of a user’s
records, never try to synchronize more than one handheld to the same user
name.
36
3
Click OK on your computer screen.
A beep sounds and the HotSync operation starts. When the HotSync
process is complete, a message showing the HotSync operation
completion is displayed on your CLIÉ handheld.
• Do not remove or move your CLIÉ handheld from the cradle during a
HotSync operation.
• Do not push the HotSync button during a HotSync operation. It might
cause errors and quitting of the operation.
• Do not enter power saving mode during a HotSync operation. If your
computer enters power saving mode during a HotSync operation, the
HotSync Manager will quit.
If the HotSync operation does not start
• Make sure that the HotSync
icon is displayed in the Windows task
tray on your computer screen.
• If the HotSync
icon is not shown in the task tray, click Start, point to
Programs (All Programs in Windows® XP), Sony Handheld, and then
click HotSync Manager. Then click the HotSync button on your CLIÉ
handheld to start the HotSync operation.
4
To open the Palm™ Desktop for CLIÉ software, doubleclick the Palm Desktop for CLIÉ icon on the Windows®
desktop or click Start, point to Programs (All Programs in
Windows® XP), Sony Handheld, and click Palm Desktop
for CLIÉ.
The Palm Desktop for CLIÉ software starts. All the main
applications on your CLIÉ handheld are also available in the Palm
Desktop for CLIÉ software. You can synchronize the information on
your computer with the information on your CLIÉ handheld.
37
Chapter 2 Setting up your Sony CLIÉ Handheld – Basics
Notes
Chapter 3
Setting up your Sony CLIÉ Handheld
– Advanced
Contents
Checking the bundled applications on your Sony CLIÉ Handheld .... 40
Overview of basic Palm OS® applications ............................ 41
Overview of Sony applications ............................................. 44
Installing the supplied applications on your computer .............. 48
Installing PictureGear™ 4.4Lite ............................................ 48
Installing QuickTime® 5 ...................................................... 48
Installing DirectX® 6 ........................................................... 49
Installing Memory Stick Export ............................................. 49
Installing Sound Converter ................................................... 50
Installing AvantGo® and other third-party applications ........ 50
Installing Acrobat Reader® 5.0 ............................................ 51
Uninstalling the supplied applications .................................. 52
Installing add-on applications on your Sony CLIÉ Handheld or
Memory Stick media ................................................................. 53
Installing add-on applications from the Palm™ Desktop for
CLIÉ software ...................................................................... 54
Installing add-on applications by beaming them from another
Palm OS® device ................................................................. 57
Installing add-on applications directly from the Installation
CD-ROM menu .................................................................... 59
Removing add-on applications ............................................. 60
Customer registration ............................................................... 61
Chapter 3
This chapter describes advanced software setup procedures
for your CLIÉ handheld and your computer. These procedures
include: checking the bundled applications on your CLIÉ
handheld, installing applications from the Installation
CD-ROM on your computer, and installing add-on
applications on your CLIÉ handheld.
Checking the bundled applications
on your Sony CLIÉ Handheld
After you make your CLIÉ handheld ready for use, start the
Application Launcher to display all the available applications on your
CLIÉ handheld.
To open an application from the Application Launcher screen
1
Tap the Home
icon.
The Application Launcher screen appears.
b
Tap the Home icon
2
Do either of the following:
• Tap the desired application icon in the Application Launcher
screen.
If you have many applications installed on your CLIÉ handheld,
tap the scroll bar to see all the available applications.
• For the four main applications, you can press the application
button on the front panel to display the selected application
immediately:
Address Book
Date Book
To Do List
Memo Pad
To quit the application and open another application
Tap the Home
icon (or press the BACK button repeatedly), and
then perform step 2 to open the desired application. The next time you
open the application, the last screen resumes.
40
Overview of basic Palm OS® applications
Your CLIÉ handheld comes with the following Palm OS basic
applications: Date Book, Address Book, To Do List, Memo Pad, and
Calculator applications. This section gives an overview of these basic
applications.
Date Book
• Enter a description of your appointment and assign it to a specific
time and date.
• Display a chart of your appointments for an entire week. The Week
view makes it easy to spot available times and any potential
scheduling overlaps or conflicts.
• Display a monthly calendar to quickly spot days where you have
morning, lunch, or afternoon appointments.
• Set an alarm to sound prior to the scheduled activity.
• Create reminders for events that are based on a particular date,
rather than time of day. Birthdays and anniversaries are easy to track
with your CLIÉ handheld.
• Attach notes to individual events for a description or clarification of
the entry in your Date Book.
Address Book
Address Book enables you to keep names, addresses, phone
numbers, and other information about your personal or
business contacts.
In Address Book, you can do the following:
• Quickly look up or enter names, addresses, phone numbers, and
other information.
• Enter up to five phone numbers (home, work, fax, etc.) or e-mail
addresses for each name.
Continued on next page
41
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
Date Book lets you quickly and easily schedule
appointments or any kind of activity associated with a time
and date.
In Date Book, you can do the following:
Checking the bundled applications on your
Sony CLIÉ Handheld
• Define which phone number appears in the Address List for each
Address Book entry.
• Attach a note to each Address Book entry, in which you can enter
additional information about the entry.
• Assign Address Book entries to categories so that you can organize
and view them in logical groups.
• Paste a PictureGear™ Pocket image to an address entry.
To Do List
To Do List is a convenient place to create reminders and
prioritize the things that you have to do.
In To Do List, you can do the following:
• Make a quick and convenient list of things to do.
• Assign a priority level to each task.
• Assign a due date for any or all of your To Do List items.
• Assign To Do List items to categories so that you can organize and
view them in logical groups.
• Sort your To Do List items either by due date, priority level, or
category.
• Attach notes to individual To Do List items for a description or
clarification of the task.
Memo Pad
Memo Pad provides a place to take notes that are not
associated with records in Date Book, Address Book, or To
Do List.
In Memo Pad, you can do the following:
• Take notes or write any kind of message on your CLIÉ handheld.
• Drag and drop memos into popular computer applications like the
Microsoft® Word software when you synchronize using the Palm™
Desktop for CLIÉ software and HotSync® technology.
• Assign memos to categories so that you can organize and view them
in logical groups.
• Write down phone numbers and other types of information. Later,
you can copy and paste this information to other applications.
42
Calc (Calculator)
Calculator enables you to perform addition, subtraction,
multiplication, division, and calculate square roots.
In Calculator, you can do the following:
• Perform basic calculations.
• Store and retrieve values.
• Display the last series of calculations, which is useful for confirming
a series of “chain” calculations.
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
43
Checking the bundled applications on your
Sony CLIÉ Handheld
Overview of Sony applications
In addition to the basic Palm OS applications, your CLIÉ handheld also
contains original Sony applications: PictureGear™ Pocket, PhotoStand,
CLIÉ Paint, MS Gate, gMovie, MS Autorun, MS Import, MS Backup,
World Alarm Clock, CLIÉ Remote Commander, and Sound Utility.
This section gives an overview of these original Sony applications.
PictureGear Pocket
The PictureGear Pocket application is the image
management software for your CLIÉ handheld.
In the PictureGear Pocket application, you can do the
following:
• View images.
• Beam your favorite image files to another CLIÉ handheld.
• Paste an image to your Address Book entry.
PhotoStand
The PhotoStand application is used to display PictureGear
Pocket images one by one like a slide show. Placed on the
cradle, your CLIÉ handheld functions as a photo stand.
In the PhotoStand application, you can do the following:
• Perform a slide show of the PictureGear Pocket images one by one.
• Display the time with the picture so that you can use it as a clock.
• Choose effect patterns or the time display mode.
CLIÉ Paint
The CLIÉ Paint application is used to draw shapes, letters,
or patterns on PictureGear Pocket images. You can also
draw from scratch on a white background. You need to
install the CLIÉ Paint application from the Installation CDROM to your CLIÉ handheld.
In the CLIÉ Paint application, you can do the following:
• Draw on a PGP format image data using multiple drawing tools.
• Draw a picture on a white background.
44
MS Gate
The Memory Stick Gate (MS Gate) application is used to
exchange Memory Stick data to and from your CLIÉ
handheld.
In the MS Gate application, you can do the following:
• Copy or move data to and from your CLIÉ handheld and Memory
Stick media.
• Delete data in Memory Stick media and in your CLIÉ handheld.
gMovie
The gMovie application is used to play a movie clip created
using the PictureGear 4.4Lite software.
In the gMovie application, you can do the following:
• Play a movie file copied from your computer on your CLIÉ
handheld.
• Play a movie file directly from Memory Stick media.
• Beam a movie file to another CLIÉ handheld.
MS Autorun
The Memory Stick Autorun (MS Autorun) application is
used to start a specified application when Memory Stick
media is inserted into your CLIÉ handheld.
In the MS Autorun application, you can do the following:
• Automatically start game software or other application stored in
Memory Stick media.
• Display specified data immediately by automatically starting the
associated application stored in Memory Stick media or your CLIÉ
handheld.
Continued on next page
45
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
• Format Memory Stick media.
Checking the bundled applications on your
Sony CLIÉ Handheld
MS Import
The Memory Stick Import (MS Import) application is used
in combination with the Memory Stick Export (MS Export)
software to copy your computer data on the Memory Stick
media inserted in your CLIÉ handheld without performing
a HotSync operation. You need to install the MS Export
software from the Installation CD-ROM on your computer
(The MS Import application is pre-installed on your CLIÉ
handheld).
In MS Import/Export, you can do the following:
• Install CLIÉ applications directly on the Memory Stick media
inserted in your CLIÉ handheld without performing a HotSync
operation.
• View and handle the contents of the Memory Stick media inserted in
your CLIÉ handheld as a removable device.
• Copy files between your computer’s hard disk and the Memory Stick
media with the Windows® Explorer.
• Choose folders other than the default folder to store CLIÉ handheld
data.
MS Backup
The Memory Stick Backup (MS Backup) application is used
to back up your CLIÉ data on a Memory Stick media, unlike
the HotSync operation that takes a backup on your
computer.
In the MS Backup application, you can do the following:
• Backup CLIÉ data on a Memory Stick media inserted in your CLIÉ
handheld.
• Restore the backup data on the CLIÉ handheld once again.
46
World Alarm Clock
The World Alarm Clock application is a software to use
your CLIÉ handheld as a world clock. You need to install
the World Alarm Clock application from the Installation
CD-ROM to your CLIÉ handheld.
In the World Alarm Clock application, you can do the
following:
• Use your CLIÉ handheld as an alarm clock to remind you of a given
time of a day of the week. You can also set your favorite sound as its
alarm.
CLIÉ Remote Commander
The CLIÉ Remote Commander application is used to
operate various multiple remote-controlled devices such as
the TV, VCR, DVD player, etc. with just your CLIÉ
handheld. You need to install the CLIÉ Remote Commander
application from the Installation CD-ROM to your CLIÉ
handheld.
In the CLIÉ Remote Commander application, you can do
the following:
• Use your CLIÉ handheld as a remote commander for four devices,
switching among them with just a single tap on the short-cut button.
You can also control more devices by selecting from the Select menu.
Sound Utility
The Sound Utility application is used to play back and
manage sound data imported from your computer. You
need to install the Sound Utility application from the
Installation CD-ROM to your CLIÉ handheld.
In the Sound Utility application, you can do the following:
• Play back, delete, and change the name of the sound data.
47
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
• View the date and time of multiple regions on a single screen.
Daylight Saving Time settings are also available.
Installing the supplied applications
on your computer
From the installation launcher window of the supplied CLIÉ
Installation CD-ROM, you can install the following image, sound, and
other applications on your computer’s hard disk.
Installing PictureGear™ 4.4Lite
The PictureGear 4.4Lite software allows you to transfer image or
movie files to and from your CLIÉ handheld from or to your computer.
You can use the PictureGear Pocket or the gMovie application to view
the transferred movie or image files on your CLIÉ handheld.
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
2
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
3
Click Install CLIÉ Utilities.
The CLIÉ utilities window is displayed.
4
Click Install PictureGear Lite.
The PictureGear 4.4Lite software installation starts.
Follow the onscreen instructions to finish installation.
Installing QuickTime® 5
The QuickTime 5 software allows you to view QuickTime movies and
is necessary for PictureGear Lite software to convert QuickTime
movies for use on your CLIÉ handheld.
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
2
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
3
Click Install CLIÉ Utilities.
The CLIÉ utilities window is displayed.
48
4
Click Install QuickTime.
The QuickTime 5 software installation starts.
Follow the onscreen instructions to finish installation.
Installing DirectX® 6
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
2
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
3
Click Install CLIÉ Utilities.
The CLIÉ utilities window is displayed.
4
Click Install DirectX 6.
The DirectX 6 software installation starts.
Installing Memory Stick Export
To use the MS Import/Export feature, you need to install the MS
Export software, a PC tool to save an application on the proper
directory in the Memory Stick media, on your computer.
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
2
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
Continued on next page
49
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
The DirectX 6 software, which is a set of graphics and sound drivers, is
necessary for the PictureGear Lite software to function properly. If you
already have DirectX 6.0 or later installed, you do not need to install
the DirectX 6 software.
Installation is necessary when you use a computer with Windows 98
installed.
Installing the supplied applications on your computer
3
Click Install CLIÉ Utilities.
The CLIÉ Utilities window is displayed.
4
Click Install Memory Stick Export.
The software installation starts. Follow the onscreen instructions to
finish the installation.
Installing Sound Converter
The Sound Converter software allows you to convert “WAVE format”
or “Standard MIDI File Format 0” files on your computer to the sound
data compatible with your CLIÉ handheld. To play back the converted
data on your CLIÉ handheld, you must install the Sound Utility
application on your CLIÉ handheld.
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
2
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
3
Click Install CLIÉ Utilities.
The CLIÉ Utilities window is displayed.
4
Click Install Sound Converter.
The software installation starts. Follow the onscreen instructions to
finish the installation.
Installing AvantGo® and other third-party applications
AvantGo Client, which is an add-on application for your CLIÉ
handheld, is a Web browser that allows you to easily access to the
AvantGo Server site and to find and upgrade contents and
applications on your CLIÉ handheld.
You can install AvantGo or other add-on applications on your
computer and then install them on your CLIÉ handheld at the next
HotSync® operation. For details, see “Installing add-on applications
from the Palm™ Desktop for CLIÉ software” on page 54.
50
Note
You must be connected to the Internet to install AvantGo.
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
3
Click FREE Third-party Software.
The FREE Third-party Software installation window is displayed.
4
Click Travel and Entertainment.
The Travel and Entertainment window is displayed.
5
Click AvantGo.
The AvantGo application installation starts. Follow the onscreen
instructions to finish the installation.
Installing Acrobat Reader® 5.0
The Acrobat Reader 5.0 software allows you to view, navigate, and
print Adobe Portable Document Format (PDF) documents. To open
and read the PDF manuals in the CLIÉ Installation CD-ROM, you need
the Acrobat Reader software installed in your computer’s hard disk.
1
Insert the Installation CD-ROM into your computer’s
CD-ROM drive.
The installation launcher window is displayed.
2
3
Click Exit to close the installation launcher window.
Click Start from the taskbar, then click Run.
The Run window is displayed.
4
Type or select “D:\PC\Acrobat\ar500enu.exe” in the text
box and click Run. (“D:” substitutes the drive letter of
your CD-ROM drive.)
You can also use Browse to specify the setup program.
The Acrobat Reader 5.0 software installation starts. Follow the
onscreen instructions to finish installation.
51
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
2
Installing the supplied applications on your computer
Uninstalling the supplied applications
In the event that you no longer need an application you installed, you
can remove an application from your computer’s hard disk as follows:
1
Click Start from the taskbar, point to Settings, and click
Control Panel.
The Control Panel window is displayed.
2
Double-click Add/Remove Programs.
The Add/Remove Programs Properties window is displayed.
3
In the Install/Uninstall tab, select the software that you
want to remove.
4
Click Add/Remove.
The confirmation dialog box is displayed.
5
Click OK to remove the software.
Follow the onscreen instructions to remove the application from
your computer’s hard disk.
Tip
Some applications have their own uninstaller program. To remove QuickTime,
for example, click Start on the taskbar, point to Programs (All Programs in
Windows® XP), QuickTime, and then click Uninstall QuickTime.
52
Installing add-on applications on your Sony
CLIÉ Handheld or Memory Stick media
Notes
• Add-on applications reside in the RAM memory of your CLIÉ handheld.
Performing a hard reset deletes all the add-on applications. However, if you
perform a HotSync® operation before the hard reset and make a backup copy,
you can restore add-on applications at the next HotSync operation.
• The add-on applications contained in the CLIÉ Installation CD-ROM are
copied on your computer’s hard disk when you install the Palm™ Desktop for
CLIÉ software. To install those applications from the Palm Desktop for CLIÉ
software on your CLIÉ handheld, follow the procedures described in the next
section.
53
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
Your CLIÉ handheld comes with various applications such as Date
Book, Address Book, To Do List, Memo Pad, Calculator, e-mail
application, etc.
In addition to these applications, you can install additional
applications called “add-on applications” from the Installation
CD-ROM on your CLIÉ handheld, or to the Memory Stick media (sold
separately) if you want to save your CLIÉ handheld’s memory space.
A variety of third-party applications are also available for your CLIÉ
handheld, such as games and other software that run on the Palm OS®.
For information on the latest third-party applications, see the Sony
official CLIÉ Web site (http://www.sony.com/clie/).
Installing add-on applications on your Sony CLIÉ
Handheld or Memory Stick media
Installing add-on applications from the Palm™
Desktop for CLIÉ software
This section describes how to install add-on applications on your CLIÉ
handheld or to the Memory Stick media using the Install Tool during a
HotSync® operation.
1
Copy or download the application you want to install
into the Add-on folder in the Sony CLIÉ Handheld folder
on your computer (example : C:\Program Files\Sony
Handheld\Add-on).
If you want to copy to a different folder, specify the folder in step 5.
2
Double-click the Palm Desktop for CLIÉ software icon on
the Windows® desktop or click Start, point to Programs
(All Programs in Windows® XP), Sony Handheld, and click
Palm Desktop for CLIÉ.
The Palm Desktop for CLIÉ software starts.
3
Click Install.
The Install Tool dialog box appears.
54
4
5
From the User drop-down list, select a user name to use.
Click Add.
The Open File dialog box appears. The supplied add-on
applications are stored in the Add-on folder.
6
Select the application(s) you want to install on your CLIÉ
handheld.
7
8
9
Click Done.
Click OK.
Perform a HotSync operation.
The application(s) you selected in step 6 will be installed on your
CLIÉ handheld. See page 36 (Step 6: Performing a HotSync®
operation for the first time) for details on a local HotSync operation.
55
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
In the Install Tool dialog box, the list of applications you selected is
displayed.
If you do not want to install an application, select it, and then click
Remove. (The application is deleted from the list but remains on
your computer’s hard disk.)
Installing add-on applications on your Sony CLIÉ
Handheld or Memory Stick media
To access the Install Tool dialog box
Do either of the following to display the Install Tool dialog box
immediately:
• Click Start on the taskbar, point to Programs (All Programs
in Windows® XP), Sony Handheld, and then click Install
Tool.
• Double-click any file with a PRC, or PDB file extension.
To install applications to the Memory Stick media
You can install applications to the Memory Stick media by performing
one of the following:
• Use the MS Import/Export applications to install
applications directly on an inserted Memory Stick media
(See the Add-on Applications Guide for details).
• To install applications through the Palm Desktop for CLIÉ
software, click Change Destination after performing step 6
on page 55. Click the file name(s) to select the file(s), then
click the arrow (>> or <<) button to select Memory Stick as
the destination and click OK. Proceed to step 7.
Note
When installing add-on applications to the Memory Stick media, be sure to
perform the HotSync operation with the Memory Stick media inserted in
your CLIÉ handheld.
If you installed applications to the Memory Stick media through Palm
Desktop for CLIÉ software
With some applications, your CLIÉ handheld may not be able to display data if
you installed the application in the Memory Stick media.
This is because the Palm Desktop for CLIÉ software installs application data in
the /PALM/Launcher directory when Memory Stick is selected. As a result,
some application data cannot be started through normal process.
If the application you installed in the Memory Stick media fail to start, copy the
data again, this time to your CLIÉ handheld. For details, see “Copying data in
Memory Stick media to your CLIÉ handheld” in the Operating Instructions
manual.
56
Installing add-on applications by beaming them
from another Palm OS® device
IR port
1
Tap the Home
icon.
The Application Launcher screen appears.
2
Tap the Menu
icon.
The menu is displayed.
3
Tap Beam.
The Beam screen appears.
4
Tap the arrow V next to Beam From, and select
Handheld or Card.
Continued on next page
57
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
Your CLIÉ handheld is equipped with an IR (infrared) port that you
can use to beam an application to another Palm OS® PDA device that
is close by and also has an IR port. You can beam applications that are
either installed in your CLIÉ handheld or stored in the inserted
Memory Stick media. The IR port is located at the top of your CLIÉ
handheld, behind the small dark shield.
Installing add-on applications on your Sony CLIÉ
Handheld or Memory Stick media
5
Tap the application you want to transfer.
Note
Some applications are copy-protected and cannot be beamed. These are
listed with the lock
icon next to them.
6
7
Tap Beam.
When the Beam dialog box appears, point the IR port
directly at the IR port of the receiving handheld.
Tip
For best results, the handhelds should be 4 to 8 inches (approximately 10 to
20 centimeters) apart, and the path between the two handhelds must be clear
of obstacles. Beaming distance to other Palm OS PDA devices may be
different.
8
58
Wait for the Beam dialog box to indicate that the
transfer is complete before you continue using your CLIÉ
handheld.
Installing add-on applications directly from the
Installation CD-ROM menu
You can also install applications directly from the supplied Installation
CD-ROM menu to your CLIÉ handheld. You do not have to start the
Palm Desktop for CLIÉ software.
Insert the Installation CD-ROM into the CD-ROM drive of
your computer.
2
Select the model of your CLIÉ handheld (PEG-T615C or
PEG-T415).
3
4
Click Install CLIÉ Add-on Applications.
Click CLIÉ Add-ons.
InstallShield Wizard starts and the Select Components window
appears.
5
Click the check box to select the add-on applications you
wish to install.
6
7
Click Next.
From the User name drop-down list, select your CLIÉ
handheld’s user name.
8 Click OK.
9 Click Done.
10 Perform a HotSync operation.
The application(s) you selected in step 4 will be installed on your
CLIÉ handheld. See page 36 (Step 6: Performing a HotSync®
operation for the first time) for details on a local HotSync operation.
59
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
1
Installing add-on applications on your Sony CLIÉ
Handheld or Memory Stick media
Removing add-on applications
If the memory of your CLIÉ handheld or Memory Stick media is full,
or you decide that an add-on application is no longer needed, you can
remove it from your CLIÉ handheld or the Memory Stick media.
Note
You can remove only add-on applications, patches, and extensions that you have
installed. You cannot remove the standard applications provided with your CLIÉ
handheld, such as Address Book or Memo Pad.
1
Tap the Home
icon.
The Application Launcher screen appears.
2
Tap the Menu
icon.
The menu is displayed.
3
Tap Delete.
The Delete screen appears.
4
Tap the arrow V next to Delete From and select
Handheld or Card.
5
Tap the application you want to delete, and tap Delete.
A confirmation message for Delete Application is displayed.
6
Tap Yes.
The application you selected in step 5 is deleted.
To cancel deletion, tap No.
7
Tap Done.
The Application Launcher screen appears again.
60
Customer registration
If you do not fill in the customer registration after installing the Palm™
Desktop for CLIÉ software, follow the instructions in this section to
complete the registration.
Note
Your computer needs to be connected to the internet to complete the registration.
1
The Sony CLIÉ Handheld Registration screen appears.
2
Click Start your registration process.
Your computer is connected to the Internet, and the user
registration Web page at the following URL is displayed:
http://www.sony.com/clie/register/
3
Follow the onscreen instructions.
61
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
Double-click the Sony CLIÉ Registration icon on the
Windows® desktop or click Start on the taskbar, point to
Programs (All Programs in Windows® XP), Sony
Handheld, and then click Sony CLIÉ Registration.
62
Chapter 3 Setting up your Sony CLIÉ Handheld – Advanced
63
For the latest support information,
check our official Sony CLIÉ Web site
http://www.sony.com/clie/