Installation manual | Furuno 2137S-BB Marine RADAR User Manual

Back
MARINE RADAR/ARPA
FAR-2137S/2837S/2137S-BB
Installation Manual
Comply with MSC.192(79)
TABLE OF CONTENTS
SAFETY INSTRUCTIONS....................... i
3.4 Adjustment Sweep Timing .................... 3-6
3.5 Suppressing Main Bang ....................... 3-7
EQUIPMENT LISTS .............................. iii
SYSTEM CONFIGURATION .................. v
3.6 Other Settings ...................................... 3-8
3.7 Dual Radar Display
(non IMO-type only) .......................... 3-16
1. MOUNTING ..................................... 1-1
1.1 Antenna Unit ........................................ 1-1
1.2 Monitor Unit.......................................... 1-8
1.3 Power Supply Unit ............................. 1-12
1.4 Control Unit ........................................ 1-13
1.5 Processor Unit ................................... 1-18
4. INSTALLING OPTIONAL
EQUIPMENT........................................4-1
4.1 Gyro Converter GC-10 ......................... 4-1
4.2 Memory Card Interface Unit ................. 4-9
4.3 DVI-RGB Conversion Kit (for VDR
connection)........................................ 4-12
2. WIRING ........................................... 2-1
4.4 BNC Connector Converter ................. 4-15
2.1 Interconnection .................................... 2-1
4.5 Junction Box....................................... 4-16
2.2 Antenna Unit ........................................ 2-2
5. INPUT/OUTPUT DATA ....................5-1
2.3 Monitor Unit.......................................... 2-7
2.4 Processor Unit ..................................... 2-8
2.5 Power Supply Unit ............................. 2-12
2.6 Changing AC Power Specification of
Processor Unit .................................. 2-12
INSTALLATION MATERIALS,
ACCESSORIES, SPARE PARTS ....... A-1
OUTLINE DRAWINGS ....................... D-1
INTERCONNECTION DIAGRAM ....... S-1
3. SETTING AND ADJUSTMENT ....... 3-1
3.1 DIP Switch Setting ............................... 3-1
3.2 Initializing Tuning ................................. 3-2
3.3 Heading Alignment............................... 3-3
www.furuno.co.jp
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone : +81-(0)798-65-2111
Fax
: +81-(0)798-65-4200
All rights reserved.
Printed in Japan
A : APR . 2004
L : APR . 12, 2011
Pub. No. IME-35210-L
(HIMA )
FAR-2137S/BB/2837S
*00014868819*
*00014868819*
* 0 0 0 1 4 8 6 8 8 1 9 *
SAFETY INSTRUCTIONS
The operator and installer must read the applicable safety instructions before attempting to
install or operate the equipment.
DANGER
Indicates a potentially hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury.
Warning, Caution
Mandatory Action
Prohibitive Action
DANGER
Wear a safety belt and hard hat when working on the antenna unit.
Serious injury or death can result if someone falls from the radar antenna
mast.
WARNING
Radio Frequency Radiation Hazard
The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful,
particularly to your eyes. Never look directly into the antenna aperture from a close distance
while the radar ius in operation or eexpose yourself to the transmitting antenna at a close
distance. Distances at which RF radiation level of 100, 50 and 10 W/m 2 are given in the table
below.
Note: If the antenna unit is installed at a close distance in front of the wheel house, your
administration may require halt of transmission within a certain sector of antenna revolution.
This is possible. Ask your FURUNO representive or dealer to provide this feature.
Model
*2
FAR-2137S
FAR-2837S
*1
*2
Antenna *1
Transceiver Magnetron
RTR-080
(S-30 kw)
MG5223F
SN30AF
0.1 m
SN36AF
0.1 m
SN30AF: 10 ft SN36AF: 12 ft
FAR-2137S: available in blackbox configuration.
i
100W/m
2
50W/m
2
10W/m
2.4 m
0.7 m
2.0 m
2
CAUTION
WARNING
Do not open the equipment
unless totally familiar with
electrical circuits and
service manual.
ELECTRICAL
SHOCK
HAZARD
Observe the following compass safe
distances to prevent deviation of a
magnetic compass:
Standard
compass
Only qualified personnel
should work inside the
equipment.
Antenna Unit
(30 kw)
Monitor Unit
(MU-201CR)
Monitor Unit
(MU-231CR)
Processor
Unit (RPU-013)
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if someone falls from the radar antenna mast.
3.95 m
2.55 m
1.55 m
1.00 m
1.85 m
1.20 m
1.35 m
0.85 m
0.30 m
0.30 m
0.95 m
0.60 m
0.65 m
0.45 m
Power Supply
Unit (PSU-007)
0.85 m
0.55 m
Memory Card
Interface Unit
(CU-200)
0.90 m
0.60 m
1.10 m
0.70 m
1.00 m
0.60 m
Monitor Unit
(MU-190)
1.65 m
1.05 m
Monitor Unit
(MU-231)
0.85 m
0.55 m
Control Unit
(RCU-014)
Control Unit
(RCU-015)
Control Unit
(RCU-016)
Turn off the power at the mains switchboard before beginning the installation.
Fire, electrical shock or serious injury can
result if the power is left on or is applied
while the equipment is being installed.
Be sure that the power supply is
compatible with the voltage rating of
the equipment.
Connection of an incorrect power supply
can cause fire or damage the equipment .
Junction Box
(RJB-001)
Switching Hub
(HUB-100)
Use only the specified power cable.
Fire or damage to the equipment can result
if a different cable is used.
Do not install the monitor unit,
processor unit or control unit where
they may get wet from rain or
water splash.
Water in the units can result in fire,
electrical shock, or damage the equipment.
Attach securely protective
earth to the ship's body.
The protective earth
(grounding) is required to the
AC power supply to prevent
electrical shock.
ii
Steering
compass
EQUIPMENT LISTS
Standard Supply
Name
Antenna Unit
Power Supply Unit
Type
Code No.
Qty
SN30AF
-
1
RSB-098
-
200 VAC 3φ 50 Hz,
220 VAC 3φ 60 Hz
RSB-099
-
380 VAC 3φ 50 Hz,
440 VAC 3φ 60 Hz
RSB-100
-
220 VAC, 3φ, 50 Hz
RSB-101
-
220 VAC, 3φ, 60 Hz
RSB-102
-
440 VAC, 3φ, 60 Hz
PSU-007
-
1
Control Unit
MU-231CR
MU-190
-
1
-
1
RCU-014
-
1
RCU-015
1
CP03-25700 000-080-435
Spare Parts*
For FAR-2837S
For FAR-2137S
AC type
Standard type
Trackball type
For antenna unit
15 m signal cable RW-9600
CP03-25710 000-080-436
Accessories*
Antenna
Chassis
for HSC
For FAR-2837S
RPU-013
CP03-27201 008-538-720
Installation Materials*
Antenna
Chassis
For FAR-2137S
MU-231
Processor Unit
Radiator
1
MU-201CR
Monitor Unit
Remarks
1
CP03-25720 000-080-437
CP03-25730 000-082-191
30 m signal cable RW-9600
50 m signal cable RW-9600
40m signal cable RW-9600
CP03-25800 000-080-434
1
Cable assy. for monitor unit
CP03-25602 008-535-940
1
For RPU-013, AC set
CP03-27301 008-538-740
1
For PSU-007
FP03-09810
008-536-010
1
For monitor unit
FP03-09850
008-535-610
FP03-09860
008-535-690
FP03-10101
008-538-730
1
For antenna unit
SP03-14404
008-535-910
1
For processor unit 100 VAC set
SP03-14405
008-535-920
SP03-14401
008-535-990
1
1
For RCU-014
For RCU-015/016
For processor unit 220 VAC set
For monitor unit, AC set
*: See lists at the end of this manual.
Optional Equipment
Name
Gyro Converter
Performance Monitor
Type
GC-10-2
PM-51
Code No.
000-080-440
000-081-261
iii
Remarks
See chapter 4.
Mandatory for IMO radar
(Continued on the next page.)
Name
Transformer Unit
Memory Card Interface Unit
External Buzzer
Control Unit
RAM Card
DVI-RGB Conversion Kit
Cable Assy.
LAN Cable Kit (with armor)
Accessories
Hand Grip
Dust Cover
Hood
Clamp Plate
Flush Mount Kit
Coupling Pedestal
Desktop Mount Kit
Console Mount Kit
BNC connector converter
Junction Box
Switching Hub
Slim Hood
Type
Code No.
RU-1803
-
RU-3305
-
RU-5693
-
RU-6522
-
RU-5466-1
-
CU-200-FAR
OP03-21
RCU-016
00RAM08MC-005
OP03-180-1
OP03-180-2
OP03-180-3
OP03-180-4
XH10P-W-6P L=20M
XH10P-W-6P L=30M
000-081-568
XH10P-W-5P-A L=10M
000-149-050
XH10P-W-5P-A L=20M
000-149-051
XH10P-W-5P-A L=30M
000-149-052
DVI-D/D S-LINK 10M
000-150-200
S03-9-5
S03-9-10
S03-9-15
CP03-28900
CP03-28910
CP03-28920
FP03-09820
FP03-09830
FP03-09840
03-163-1201
03-163-2101
FP03-11500
FP03-11000
OP03-182
FP03-09870
OP03-198
OP03-183
OP03-184
OP03-185
FP03-10201
FP03-10202
DSUB-BNC-1
RJB-001
HUB-100
FP03-11010
FP03-11510
008-206-640
000-030-097
008-209-160
Remote type, W/FP03-09860
8 MB
Mounted at Factory.
Mounted in field. See chapter 4.
Mounted in console at factory
Mounted in console in filed.
Between processor
20 m
and control unit
30 m
Between control units, 10 m
Between control units, 20 m
Between control units, 30 m
Monitor-Processor, 10m
For external radar, 5 m, 8-8P
For external radar, 10 m, 8-8P
For external radar, 15 m, 8-8P
000-082-658
FR-FTPC-CY 10 m
Modular
000-082-659
FR-FTPC-CY 20 m
connector
000-082-660
FR-FTPC-CY 30 m
MPS588-C, 2pcs
008-535-560
Hanger assy. for MU-201CR
Hanger assy. for MU-231CR
For monitor unit
For MU-201CR
For MU-231CR
For MU-201CR
For MU-231CR
For RCU-014
000-080-299
004-376-740
008-545-590
008-536-070
008-545-610
008-545-600
000-149-748
000-149-749
008-206-650
008-536-020
008-535-570
100-307-260
100-307-270
001-020-090
008-571-680
008-535-620
008-535-630
001-008-050
008-535-640
008-535-650
008-535-660
008-539-530
008-539-540
000-148-528
iv
Remarks
For processor unit,
440 VAC → 100 VAC
For de-icer , 110/115/220/230 VAC
→ 100 VAC
For RSB-098/099,
110 V →220 VAC
Not
For RSB-098/099,
available
220 V →200 VAC
for HSC
For RSB-098/099,
440 V →220 VAC
W/CP03-27430, See chapter 4.
For control unit RCU-014/015/016
For RCU-014&MU-201CR
For RCU-014& MU-231CR
For RCU-014
For CU-200
For CU-200
For VDR
-
For more than 100m antenna cable
-
See HUB-100 Operator’s manual.
001-033-140
For MU-231CR display unit
001-034-390
For MU-201CR display unit
SYSTEM CONFIGURATION
Radiator
SN30AF/
SN36AF
ANTENNA UNIT
Performance Monitor
Chassis
RSB-098/099
RSB-100/101/102 (for HSC)
POWER SUPPLY
UNIT PSU-007
RJB-001 **
MONITOR UNIT
MU-201CR
or
MU-190
(FAR-2137S)
*
MU-231CR
or
MU-231
(FAR-2837S)
***
RU-5693
***
RU-6522
***
RU-5466-1
EPFS 1)
(Navigator)
IEC-61162 Serial Data
(Input/Output)
SDME 2)
Speed Log
IEC-61162 Serial Data
(Input)
3)
RJB-001 **
PROCESSOR UNIT
RPU-013
100-230 VAC
Control Unit
RCU-016
(Remote)
Sub Display
Gyro Converter
GC-10
Gyrocompass
CONTROL UNIT
RCU-014
(Standard)
or
RCU-015
(Trackball)
Alarm****
VDR
AD-100
Switching HUB
HUB-100
AIS
Track Control Unit
AC spec. only
MEMORY CARD
INTERFACE UNIT
CU-200-FAR
External Monitor
Transformer Unit
RU-1803
: Standard
: Option
: Dockyard supply
*: For FAR-2137S-BB, a monitor unit is prepared by user. See page 1-8. Category of Units
These monitors have been approved by the IMO, MU-190/201CR for CAT2, Antenna Unit: Exposed to weather
MU-231/231CR for CAT1. If a different monitor is to be used, its effective
All other units: Protected from weather
diameter must meet the applicable Category requirements:
CAT 1: effective diameter 320 mm or higher, CAT 2: effective diameter 250 mm or higher
Refer to their operator's manuals for details.
**: Used for antenna cable more than 100 m.
***: Not available for HSC spec.
****: Contact output for Alarm
(Load current) 120mA, (Polarity) No.1/2: Normally Close, No.3/4: Normally Open
Serial I/O for alarm is also possible, which complies with IEC 61162-1.
1) Connect the EPFS which is approved in accordance with the requirements of the IMO in
resolution MSC. 112(73) is used.
2) Connect the SDME which is approved in accordance with the requirements of the IMO
in resolution MSC.96(72) is used.
3) Use the gyrocompass having an update rate that is adequate for the ship’s rate of turn.
v
About the category sticker
This radar meets the requirements in IEC62388 (Marine navigation and radio
communication equipment and systems-Shipborne radar-Performance requirements,
method of testing and required test results).
Check the appropriate box on the sticker which is pre-attached on the processor unit,
according to your radar’s specification. Refer to the table shown below to confirm your
category.
Category
Radar Type
Antenna rotation speed
CAT 1
FAR-2817, FAR-2827, FAR-2837S, FAR-2827W,
FAR-2837SW
Normal speed
CAT 1H
FAR-2817, FAR-2827, FAR-2837S
HSC
CAT 2
FR-2117/BB, FAR-2127, FAR-2127-BB,
FAR-2137S, FAR-2137S-BB
Normal speed
CAT 2H
FAR-2117, FAR-2117-BB, FAR-2127,
FAR-2127-BB, FAR-2137S, FAR-2137S-BB
HSC
vi
1. MOUNTING
NOTICE
Do not apply paint, anti-corrosive sealant
or contact spray to coating or plastic
parts of the equipment.
Those items contain organic solvents that
can damage coating and plastic parts,
especially plastic connectors.
1.1
Antenna Unit
Mounting considerations
• The antenna unit is generally installed either on top of the wheelhouse, on the radar mast,
or on a suitable platform. Locate the antenna unit in an elevated position to permit
maximum target visibility.
• A line of sight from the antenna unit to the bow of the ship should hit the surface of the
sea in not more than 500 m or twice the ship’s length, depending which value is smaller,
for all load and trim conditions.
less than 500 m or twice the ship’s length
• Mount the antenna unit so that any blind sectors caused by objects (mast, etc.) are kept
to a minimum. No blind sector should exist in arc of the horizon from right ahead to 22.5°
aft of the beam to either side (see Figure 1 below). Also, individual blind sectors of more
than 5°, or the total arc of both blind sectors of more than 20°, should not occur in the
remaining arc (Figure 2). Note that any two blind sectors separated by 3° or less are
regarded as one sector.
90
270
a, b, c: less than 5 respectively
a+b+c+... : less than 20
22.5
22.5
less than 3
Figure 1
Figure 2
1-1
1. MOUNTING
• Install the antenna unit safely away from interfering high-power energy sources and other
transmitting radio antenna.
• Keep the lower edge of the antenna unit above the safety rail by 500 mm or more.
• Two antenna units should be mounted as below:
more than 20
more
than 1 m
• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in
the bow direction, especially zero degrees ±5°, to prevent blind sectors and false echoes
on the radar picture.
• It is rarely possible to place the antenna unit where a completely clear view in all
directions is available. Thus, you should determine the angular width and relative bearing
of any shadow sectors for their influence on the radar at the first opportunity after fitting.
• Locate a direction finder antenna clear of the antenna unit to prevent interference to the
direction finder. A separation of more than two meters is recommended.
• A magnetic compass will be affected if the antenna unit is placed too close to the
magnetic compass. Observe the compass safe distances on page ii to prevent deviation
of the magnetic compass.
• Do not paint the radiator aperture, to ensure proper emission of the radar waves.
• The antenna base is made of cast aluminum. To prevent electrolytic corrosion of the
antenna base, use the seal washers and corrosion-proof rubber mat and ground the unit
with the ground wire (supplied).
• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial
performance and hot gases may distort the radiator portion. The antenna unit must not be
mounted where the temperature is more than 70°C.
• Leave sufficient space around the unit for maintenance and servicing. See the antenna
unit outline drawing for recommended maintenance space.
1-2
1. MOUNTING
Installation precaution for S-band antenna unit
If an S-band antenna unit is mounted near the end of a platform to provide sufficient rotation
clearance for the radiator, the antenna unit, because of its weight, swings up and down by
ship’s vibration and rolling. This exerts excessive levels of stress at the base of the radiator,
which can damage the radiator. To prevent this, relocate the antenna unit, or if relocation is
not possible, reinforce the platform.
Mast for
DF, etc.
Remarkable vibration
(pitching)
Mounting
position
EXAMPLE
Mast for DF
Mount the antenna unit
directly on the mast or on
the platform, as near as
possible to center of the
mast.
Mounting precaution for S-band antenna unit
1-3
1. MOUNTING
Antenna unit assembling
The antenna radiator and the antenna housing are shipped in separate packages.
Assemble them as below. The antenna unit may be assembled before hosting it to the
mounting platform. However, do not lift the antenna unit by the radiator.
Antenna unit assembling procedure
1.
2.
3.
4.
Screw the guide pins (2 pcs.) in the radiator.
Remove the protective cap from the choke guide and radiator.
Grease O-ring and set it to the groove of the choke guide.
Place the radiator on the radiator bracket. (Radiator direction is shown by the logo on
the bracket. If reversely oriented the radiator cannot be set to the bracket.)
5. Loosely fix the radiator to the radiator bracket with hex bolts (M10x25), spring washers
and flat washers.
6. Remove the guides pins and tighten hex bolts.
Antenna radiator
Radiator
front
Guide pin (2 pcs.)
Arrow mark for the radiator front.
Assembling the radiator bracket
CAUTION
Be sure to remove the guide pins
after fixing the radiator.
Injury may result if the guide pins loosen
and fall.
1-4
1. MOUNTING
How to lift the antenna unit
1. Fix the antenna radiator to the antenna unit chassis as shown on page 1-4.
2. Attach the lifting fixtures and collars as shown below.
3. Position the radiator as shown below and arrange the ropes A and B.
Lifting fixture
Supplied as accessories.
Remove after installation.
Collar for fixing
Spring washer
Plat washer (M12)
Hex bolt (M12x20)
(Torque 63.5Nm)
Remove lifting fixture, coat threads
of hex bolts with silicone grease, and
then insert bolts in antenna chassis.
Lifting hook (2 pcs.)
B
1.8m
*
A
2m
*
* Protect radiator with
cardboard or cloth at
locations marked with
asterisk.
Attachment of lifting fixtures, collar and ropes
1-5
1. MOUNTING
Fastening the antenna unit to the mounting platform
See the figure on the next page for antenna unit mounting.
1. Referring to the antenna outline drawing, drill eight fixing holes of 15 mm in diameter in
the radar mast platform or the deck.
• The diameter of the mast for fixing the antenna unit platform must be over 250 mm.
• The thickness of the antenna unit platform must be over 15 mm.
• The reinforcement rib must be installed diagonally as shown below.
Over 15mm
Use two nuts.
250mm diameter or more,
6 mm thick or more
Install the reinforcement
rib diagonally.
Ship's bow
Bottom view
Installation of reinforcement ribs
2. Place the corrosion-proof rubber mat (supplied) on the mounting platform.
3. Hoist the antenna unit as shown on page 1-5 and place it on the rubber mat. Orient the
cable gland toward the ship’s stern (or port, starboard). Remove the lifting fixtures and
collars.
4. Fix the antenna base to the mounting platform with four M12x70 hex bolts, nuts,
washers and seal washers (supplied). For the unit with the performance monitor (PM),
orient the PM toward the ship’s stern.
5. Arrange the grounding terminal at the nearest grounding spot with the M6x25 hex bolt,
nut and washers. Then, fix a ground wire (RW-4747, 340 mm) to the terminal.
6. Connect the other end of the ground wire to the ground terminal of the antenna unit.
7. Coast grounding terminal and fixing bolts on the antenna unit with silicone sealant
(supplied).
1-6
1. MOUNTING
Seal
washer
Corrosion
proof
rubber
mat
Use two nuts.
(Torque 63.5Nm)
Ground terminal
G1_1/4-A
Set corrosion-proof rubber mat,
bolt antenna unit to mounting
location, and coat exposed
hardware with silicone sealant.
Hex bolt
Flat washer
Flat washer
Spring washer
Hex nut
Ground wire
Coat with
silicone
sealant.
Coat with silicone sealant after
fastening ground wire.
OR
Ground wire
Hex nut
Spring washer
Flat washer
Hex bolt
Ground wire
Welding
Antenna chassis
Arrange ground terminal as close
as possible to antenna unit.
Ground terminal provided on antenna base.
Mounting of antenna unit
1-7
1. MOUNTING
1.2
Monitor Unit
The monitor unit can be flush mounted in a console panel, or mounted on a desktop using
the optional accessories. For MU-190/231, see the applicable Operator’s Manual(s).
Note: FAR-2137S-BB has no monitor unit. Prepare a suitable one locally.
Recommended monitor: SXGA (1280x1024), aspect ratio 5:4
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Select a location where the display unit can be viewed conveniently and where the
screen can be viewed while facing towards the bow.
• Select a suitable mounting location considering the applicable distance.
• The optimal viewing distances for the radar display units are: MU-170C: 920 mm,
MU-201CR: 1080 mm, MU-231CR: 1200 mm.
• Locate the unit out of direct sunlight and away from heat sources because of heat that
can build up inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Leave sufficient space on the sides and rear of the unit to facilitate maintenance.
• A magnetic compass will be affected if the monitor unit is placed too close to the magnetic
compass. Observe the compass safe distances on page ii to prevent deviation of a
magnetic compass.
Mounting procedure
Flush mounting
Follow the procedure below to mount the monitor unit in a console panel.
1. Make cutout in mounting location referring to the outline drawing shown below.
2. Insert the monitor unit to the hole and fix it by four tapping screws (6x30).
3. Attach panel hooks near the fixing holes (upper two locations). These are used to pull
out the monitor unit from a console panel for servicing.
4. Attach four panel covers to the fixing holes.
296 ± 1
454
4-FIXING HOLES
(79)
296 ± 1
420
506 ± 1
490
506 ± 1
534
Monitor unit MU-201CR
(For FAR-2137S)
1-8
4-φ8
FIXING HOLES
30
80
1. MOUNTING
296 ± 1
454
4-FIXING HOLES
(79)
296 ± 1
420
506 ± 1
506 ± 1
534
490
4-φ8
FIXING HOLES
30
80
Monitor unit MU-201CR
(For FAR-2137S)
4-φ8 FIXING HOLES
313 ± 1
505
4-FIXING HOLES
(96)
313 ± 1
471
570 ± 1
554
570 ± 1
598
30
80
Monitor unit MU-231CR
(For FAR-2837S)
Flush mounting of monitor unit
Panel hook
Panel cover
Fixing screw
Attaching panel hook and panel cover
Note: If you need to remove the monitor unit from the mounting panel, remove the four
panel covers with your fingernail and use two panel hooks supplied as accessories to
lift the monitor unit.
Desktop mounting
Use the optional accessories to mount the monitor unit on a desktop.
• For FAR-2137S: FP03-09820 (Code No.: 008-535-560)
• For FAR-2837S: FP03-09830 (Code No.: 008-536-020)
1-9
1. MOUNTING
Contents of FP03-09820/09830
Name
Type
Code No.
Qty
Hanger L
03-163-1111
100-305-141
1
Hanger R
03-163-1112
100-305-181
1
03-163-1113
100-305-191
03-163-2071
100-305-371
Hole plug
CP-30-HP-13
000-160-074-10
2
Plastic rivet
KB-13 Rivet Black
000-570-276-10
4
Hex. bolt
M6x25
000-162-949-10
4
Hex. bolt
M10x30
000-162-884-10
2
Spring washer
M10
000-864-261
2
Flat washer
M10
000-864-131
2
Hanger stay
1
Remarks
For FAR-2137S
For FAR-2837S
1. Assemble two hangers and hanger stay with two hex bolts (M10x30), flat washers and
spring washers and cover each hex bolt with hole plug.
2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard
supply).
3. Fasten the monitor unit to the mounting hanger assembly with four hex bolt (M6x25,
supplied).
4. Cover each hex bolts with panel cover.
5. Cover each holes for hand grip on the hangers with plastic rivet (4 pcs).
Hanger (L)
M12 bolts for fixing (Torque 63.5Nm)
(Dockyard supply)
Hanger stay
Hanger (R)
Panel cover
Plastic rivet
Flat Washer M10
Spring Washer M10
Hex bolt (M6x25)
(Torque 7.6Nm)
Hex bolt M10x30
(Torque 36.5Nm)
Hole plug
Panel cover
To remove this, insert fingernail in groove.
Monitor Unit
1-10
1. MOUNTING
The hand grip is optionally available for the desktop mounting monitor unit.
Wave washer
Rosette washer
Handle
Screw M6x20
(Torque 7.6Nm)
Hood (option)
When it is too bright in the daytime, use the optional hood to shade the screen.
• For FAR-2137S: FP03-11500 (Code No.: 001-020-090)
• For FAR-2837S: FP03-11000 (Code No.: 008-571-680)
Name
Hood (21)
Hood (23)
Fixing plate
Screw
Contents of hood
Type
Code No.
FP03-11501
001-020-120
FP03-11001
008-571-700
03-163-2202-0
100-335-560-10
M4x10 D=13 US304
000-862-543
Qty.
1
1
4
4
Remarks
For FAR-2137S
For FAR-2837S
1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts
(supplied).
Flush mounting: Fasten the display unit to the mounting location, and then attach the
fixing plates with four self-tapping screws.
Hex head bolt
Fixing plate
Fixing hole
2. Attach the hood to the display unit (the hood is outside of the fixing plates).
3. Fasten the hood to the fixing plates with four screws supplied (M4x10).
1-11
1. MOUNTING
1.3
Power Supply Unit
The Power Supply Unit PSU-007 does not contain usual operating controls. Therefore, it
can be installed in any recessed place either in vertical or horizontal position. (For the
console mount display unit, the PSU-007 can be installed inside the console.) However,
select a dry and well-ventilated location and observe the compass safe distance to prevent
deviation of a magnetic compass. See page ii.
1. Open the cover of the power supply unit.
2. Fasten the unit to chosen location with four self-tapping screws 5x20.
3. After connecting cables, attach the cover.
110
11
126
4- 6
FIXING HOLES
#30
130
#30
CABLE ENTRY
1-12
1. MOUNTING
1.4
Control Unit
The control unit may be mounted on a tabletop, with or without the KB fixing metal
(supplied), which mounts the control unit at an angle.
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Select a location where the control unit can be operated conveniently.
• Locate the unit away from heat sources because of heat that can build up inside the
cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Determine the mounting location considering the length of the signal cable between the
control unit and the processor unit. (The signal cable comes in lengths of 10 m).
• A magnetic compass will be affected if the control unit is placed too close to the magnetic
compass. Observe the compass safe distances on page ii to prevent deviation of a
magnetic compass.
Fixing with KB fixing plate
1. Fix the KB fixing plate to the bottom of the control unit.
2. Attach cushions (three for RCU-014, two for RCU-015/016) to the bottom of the control
unit as shown below.
3. Fix it to a desired location with self-tapping screws (local supply).
KB fixing plate
Cushion
Side view for RCU-014/015/016
1-13
1. MOUNTING
Fixing without KB fixing metal
1. Drill four mounting holes of 5 mm diameter referring to the outline drawing at the back of
this manual.
2. Fix the control unit with four screws (M4) from under side of the tabletop. (The M4
screws with a sufficient length for the thickness of the tabletop should be provided
locally.)
180
136±1
#70
4-M4 (Fixing holes)
(bottom)
308±1
398
Control Unit RCU-014
24
32
F3
180
136±1
F1
F2
F4
110±1
160
4-M4 (Fixing holes)
(REAR)
RCU-015/016
Flush mounting
Use the optional flush mount kit FP03-09870 to mount the control unit RCU-014, RCU-015
and/or RCU016 to a console panel.
Name: Flush mount kit
Type: FP03-09870
Code No.: 008-535-630
No.
Name
Type
Code No.
Qty
1
Mount plate
03-163-7531
100-306-261
4
2
Hex nut
M5
000-863-108
4
3
Wing screw
M5X40
000-162-682-10
4
4
Pan head screw
M4X12
000-163-192-10
4
1-14
1. MOUNTING
1. Prepare a cutout in the mounting location as shown in the figure below.
176 ±2
170±2
388±2
150 ±2
For RCU-014
For RCU-015 and RCU-016
53
(P)
#70
92
53
#70
86
(P)
2. Set the control unit to the cutout.
3. Attach the mounting plate to the control unit with four screws from the rear side.
4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing
screw.
5. Fasten each wing screws and then fasten the hex nuts as shown in the figure below.
171
Note:
RCU-014
P<
= 10
RCU-015/RCU-016
1-15
1. MOUNTING
To connect RCU-016 in series with RCU-014
1. Pass the cable derived from RCU-016.
2. Connect the connector
of the cable to J502.
3. Clamp the copper part of the cable with the cable clamp.
Inside of RCU-014
1-16
1. MOUNTING
To change the cable entry
To change the cable entry from the side (default) to the bottom, modify the unit as shown
below.
Bottom of the unit
Screw M3X8
(Torque 0.78Nm)
2. Pull out the cable.
3. Pass the cable from this hole.
Cable clamp
03-163-7804
Screw M4X8
(Torque 1.47Nm)
4. In here, clamp the copper part
of the cable with the cable
clamp removed at step1.
1. Remove the
cable clamp.
(Torque 1.47Nm)
J522: If you connect RCU-016 in series with RCU-015, plug in here.
RCU-015/016: Changing cable entry
1-17
1. MOUNTING
1.5
Processor Unit
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Locate the processor unit away from heat sources because of heat that can build up
inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Leave sufficient space at the sides and rear of the unit to facilitate maintenance.
• A magnetic compass will be affected if the processor unit is placed too close to the
magnetic compass. Observe the compass safe distances on page ii to prevent deviation
of a magnetic compass.
Mounting procedure
1. Fix the unit with four M6 bolts, or self- tapping screws.
#50
2-φ7 FIXING HOLES
340±1
410
380
25
385
370±1
R3
.5
7
350±1
2-FIXING NOTCH
Floor mounting or bulkhead mounting
Note: If you fix the unit, cable entry upside, never remove the screw M3x10 that joints
the upper case assy. and lower case assy. of the processor unit.
Upper case assy.
Lower case assy.
Screw
M3X10
Never remove this screw.
Processor unit
1-18
2. WIRING
Wiring consideration
• To lessen the chance of picking up electrical interference, avoid where possible routing
the signal cable near other onboard electrical equipment (radars, transmitting radio
antennas, etc.) Also avoid running the cable in parallel with power cables. When crossing
with other cable, the angle should be 90°to minimize the magnetic field coupling.
• The signal cable run between the antenna and processor units is available in lengths of
15 m (standard), 30 m and 50 m. Whatever length is used it must be unbroken; namely,
no splicing allowed. Use the signal cable as short as possible to minimize attenuation of
the signal.
• The radar should be connected to an emergency power source, as required by SOLAS
II-1.
2.1
Interconnection
Monitor unit
Antenna unit
For HSC
220 VAC, 3φ, 50 Hz
220 VAC, 3φ, 60 Hz
440 VAC, 3φ, 60 Hz
*
110 VAC, 3φ, RU-5693
60 Hz
*
220 VAC, 3φ, RU-6522
50 Hz
*
440 VAC, 3φ, RU-5466-1
50 Hz
TB801
TB802
Junction Box
RJB-001**
RW-9600
15/30/40/50 m
(Max.100 m)
Processor unit
DVI-D/D SINGLELINK, 5 m/10 m
440 VAC, 3φ, 60 Hz
380 VAC, 3φ, 50 Hz
DPYC-1.5
TPYCY-2.5
220 VAC, 3φ, 60 Hz
200 VAC, 3φ, 50 Hz
TPYCY-2.5
POWER SUPPLY
UNIT PSU-007
DPYC-2.5
Control unit
(RCU-014 or RCU-015)
100-230 VAC
Memory card I/F unit
CU-200-FAR
Junction Box
RJB-001**
XH10P-W-5P-A
L=10/20/30m
Control unit
(RCU-016)
XH10P-W-6P L=1.5/10/20/30 m
DPYC-2.5
100-115 VAC/220-230 VAC
*: Not available for HSC
**: If the length of the antenna cable is more than 100m, use Junction box
RJB-001. However, the maximum length is 300m.
: Cable requires fabrication
F1
F2
F3
F4
Standard Interconnection
2-1
2. WIRING
2.2
Antenna Unit
G1-A
G3/4-C
Gland for power cable
Antenna motor switch
G1_1/4-A
G1_1/4-A
Gland for signal cable (RW-9600)
1.
2.
3.
4.
5.
Antenna unit, bow view
Open the right side cover on the antenna unit with the hex wrench.
Unfasten the cable gland for the signal cable and remove the gasket, flat washers and
blind lid.
Fabricate the signal cable RW-9600 as follows.
Outer sheath
Armor Inner sheath
Shield
a) Remove the outer sheath, armor and
inner sheath as shown right.
b) Unravel the shield to expose the
20mm
460mm
5mm
wires in the inner layer.
c) Shorten each core considering its
location on the terminal board TB801.
Coaxial cable
360
d) Trim each wire (except coaxial wire)
Vinyl cable
considering its location on the
Shield
terminal board.
Wire
6
e) Trim the shield leaving 200 mm and
attach crimp-on lug FV5.5-4.
14 5 9
f) Remove insulation of each wire by
200
mm
Conductor
about 6 mm.
Fold back shield.
FV5.5-4
g) Fabricate the coaxial cable as shown
Shield wire
Coaxial cable
right.
As shown in the figure below, slide the clamping gland, flat washer, gasket and flat
washer on the signal cable.
Fold back armor and pass the flat washer as shown in the figure below. Cut and trim the
armor around the flat washer.
Flat washer
Vinyl sheath
Clamping gland
Gasket
Cut and trim armor.
Passing clamping gland, washers and gasket on the signal cable
2-2
2. WIRING
TB801
TB801
Coaxial cable
TB board
Pass the signal cable
RW-9600.
TB802
Clamp shield of coaxial cable.
Grounding point for the shield.
Antenna unit, port side view
6. Confirm that armor is grounded between two flat washers.
7. Coat the screw part of the clamping gland with silicone sealant and tighten it.
8. Using the opener, insert each core (except coaxial cable) to appropriate connector plug
on the TB801.
9. Loosen two screws and slide the TB board assembly upward and pull out it.
10. Connect the coaxial cable to TB802 on the TB board and clamp the shield with the
cable clamp on the TB board.
Wiring for WAGO connector
Press downward.
Wiring for Coaxial cable
Clamp shied with bracket.
Terminal opener
Wire
Twist
WAGO connector
Procedures
1. Twist the conductor.
2. Press the terminal opener downward.
3. Insert the wire to hole.
4. Remove the terminal opener.
5. Pull the wire to confirm that it is ecure.
Tighten conductor with screw.
CAUTION
Do not use crimp-on lug to prevent
contact resistance from increasing.
11. Remount the TB board assembly.
12. Connect the shield wire to the grounding point as shown in the figure above.
13. Seal the cable gland with putty.
2-3
2. WIRING
Fabricating power cable TPYCY-2.5
1. Open the left side cover on the antenna unit with the hex wrench.
2. Fabricate the cable as shown below. Use TPYCY-2.5 (Japan Industry Standard) cable or
equivalent.
Cable TPYCY-2.5
∅ = 15.5 mm
Sheath
Approx. 170 mm
Armor
25 mm
5 mm
Vinyl
sheath
FV2-4
Anti-corrosive
Vinyl sheath
Armor
Sheath
Conductor
S = 2.5 mm2
∅ = 2.01 mm
Fabricating the power cable TPYCY-2.5
3. At the power cable gland on the antenna unit, unfasten the clamping gland and remove
gasket, flat washers and blind lid.
4. As shown in the figure below, slide the clamping gland, washers and gasket onto the
power cable. Fold back the armor by 5 mm, and then pass it through the two flat
washers.
Flat washer
Vinyl sheath
Clamping gland
Gasket
Cut and trim armor.
Passing clamping gland, washers and gasket on power cable TPYCY-2.5
5. Coat the screw part of the clamping gland with silicone sealant and tighten it.
6. Pass the power cable behind the terminal block, and then pass it through the locking
wire saddle.
7. Fix the crimp-on-lug FV2-4 (blue) to each conductor.
2-4
2. WIRING
Terminal board
for power cable
Pass the power
supply cable here.
Antenna unit, left view
8. Connect crimp-lug to the terminal block referring to the interconnection diagram.
9. Attach the cover (torque: 7.65 N·m).
10. Seal the cable gland with putty.
2-5
2. WIRING
2.3
Monitor Unit
Two cables are terminated at the display unit: the signal cable from the processor unit (5 m
or 10 m cable) and the power cable from the ship’s mains. The signal cable comes with a
connector preattached to it for connection to the display unit. Fabricate the power cable as
below. Use DPYC-2.5 (Japan Industry Standard) cable or the equivalent. For MU-190/231,
see the applicable Operator’s Manual(s).
Fabricating the power cable
1.
2.
3.
4.
5.
Cut armor of the cable by 40 mm.
Cut vinyl sheath by 35 mm.
Remove insulation of wires by about 10 mm. Fix crimp-on lugs to the conductors.
Peel paint of the armor by 40 mm.
Cover the end of armor with vinyl tape.
(a)
Armor
DPYC-xx
Approx. 40 mm
35 mm
(b)
Vinyl sheath
10 mm
Armor
(c)
Conductor
2
S = 2.5 mm
φ = 2.01 mm
40 mm: Peel paint.
(d)
(sectional view)
Taping
Fabricating power cable DPYC-2.5
MU-231CR
MU-201CR
Cable entrance for signal cable
(The connector with no EMI core
should be connected to the monitor unit.)
Cable entrance for power cable
Monitor unit (rear panel)
2-6
2. WIRING
2.4
Processor Unit
Four cables are terminated at the processor unit: the antenna unit cable, display unit cable,
control unit cable and the power cable. Cables other than the power cable come with a
connector preattached to them for connection to the processor unit. Fabricate the power
cable as below. For the power cable, use DPYC-2.5 (Japan Industry Standard) or the
equivalent.
Note: Pass the AC line through a double-contact breaker (shipyard supply).
Fabricating the power cable
1.
2.
3.
4.
5.
Cut armor of the cable by 40 mm.
Cut vinyl sheath by 35 mm.
Remove insulation of wires by about 10 mm. Fix crimp-on lugs to the cores.
Peel paint of the armor by 40 mm.
Cover the end of armor with vinyl tape.
(a)
Armor
DPYC-2.5
Approx. 40 mm
35 mm
(b)
Vinyl sheath
10 mm
(c)
40 mm: Peel paint.
(d)
Taping
Fabricating power cable DPYC
2-7
2. WIRING
Connection of cables
The power cable is connected to the terminal board on the rear panel and the signal cable
from the Monitor unit is connected to the DVI-D connector. Other cables are connected to
the printed circuit board 03P9342.
Power cable clamp
Monitor unit
Power cable terminal board
*
Network
DVI-D monitor
Remove the
protection cover.
F70
FUSE
1
15
DC/AC
F1
2
Control unit**
Heading senor
Speed log
Navigator
Power cable
9 14
ACK
Cable clamp
17
21
2
3
4
5
HDG
φ9
6
18
19
20
RSD
φ18.9
1
7
AIS
AD100
8
28
GYRO
PSU004
24
φ7.4
VDR IN
24'
φ7
26
VDR OUT
Memory Card IF unit
VDR OUT
Antenna unit
GND terminal
VDR IN
Gyrocompass
AD-100
AIS
Processor unit
*: The connector side which EMI core is attached should be connected to the
processor unit.
**: The configuration of optional cables between the processor unit and the
control unit is as follows. Note that the cable fabrication for each end is
different.
Control unit
Processor unit
150 mm
20/30 m
300 mm
Cable XH10P-W-6P L=20/30M
When the RCU-016 is installed, optional cable (XH10P-W-5P-A, L=10/20/30M) is required.
Cable fabrication for each end is the same.
Control unit
Control unit
150 mm
10/20/30 m
XH10P-W-5P-A L=10/20/30M
2-8
150 mm
2. WIRING
Location of connectors
Open the processor unit as follows and the 03P9342 board appears.
Cable clamp
03P9342
J621
J612
J608
Gyro converter board
or AD-100
External alarm
J607
Speed log
J620
Track control
AIS
J611
J606
Navigator
J619
J605
J603
ECDIS
Gyro converter board
Sub display*
(SEMI-LOG)
Sub display*
(FULL-LOG)
Master radar
J618
J610
J604
J602
PSU
J617
Cable from control unit
Cable from Power
supply unit
J616
Cable from antenna unit
J614 J615
J601
+ 12 V for card I/F
J613
Heading sensor
PC
J609
J654
Tx HV line
Coaxial wire
03P9342
*: See page 2-11 for details.
2-9
2. WIRING
Cable fabrication for the cables connected to the 03P9342 board
•
Signal cable RW-9600 (Between antenna unit and processor unit)
Vinyl sheath
Armor
Shield
450
60
5
After exposing cores,
wind shield around the armor.
Vinyl tape
6
14 5 9
Coaxial cable
Conductor
Clamp here by cable clamp.
Fold back shield.
Coaxial cable
•
Other cables for optional units
Use TTYCS-1 or TTYCS-4 (Japan standard cable) or equivalent.
φ = 18.5 mm
Armor
Armor
Sheath
Sheath
Shield
φ = 10.1 mm
Shield
Conductor
S = 0.75 mm 2
φ = 1.11 mm
Conductor
S = 0.75 mm 2
φ = 1.11 mm
TTYCS-1
Armor
TTYCS-4
60: Peel paint.
Shield
L= Depends on equipment
connected. Measure at
the processor unit.
L
5
Vinyl tape
After exposing cores,
wind shield around the armor.
6
Clamp here by cable clamp.
Wiring for WAGO connector
Press downward.
Wiring for Coaxial cable
Clamp shied with bracket.
Terminal opener
Wire
Twist
WAGO connector
Procedures
1. Twist the conductor.
2. Press the terminal opener downward.
3. Insert the wire to hole.
4. Remove the terminal opener.
5. Pull the wire to confirm that it is ecure.
2-10
Tighten conductor with screw.
CAUTION
Do not use crimp-on lug to prevent
contact resistance from increasing.
2. WIRING
Connection of Sub-display
A conventional remote display and/or FAR-2107 series radar can be connected to J617 and
J618 in the processor unit as a sub-display. However, the control for GAIN and STC are
different depending on J617 and J618. Refer to the table to connect sub-displays.
Port
J617
Conventional remote
display
FAR-2107 series radar
Overall gain
Even if input video level is
adjusted to 4 Vp-p, the
gain is 8 db lower than
that on the master radar.
The gain is 8 dB lower than
that on the master radar.
GAIN control
The GAIN control is
effective.
The GAIN control has no
effect.
STC control
The STC control is
effective.
The STC control has no
effect.
Overall gain
When input video level is
adjusted to 4 Vp-p, the
gain becomes the same
as that on the master
radar.
The gain is almost same as
that on the master radar.
GAIN control
The GAIN control is
effective.
The GAIN control has no
effect.
STC control
The STC control is
effective, however this
control is added on the
signal adjusted by the
master radar. So this port
is not recommended to
use .
The STC control has no
effect.
(FULL-LOG)
J618
(SEMI-LOG)
2-11
2. WIRING
2.5
Power Supply Unit
Wire the unit as shown in the interconnection diagram.
Thermal relay
Relay
K2: Connect
input line.
XK1: Connect output line.
TB1: Connect control line.
Cable clamp: Clamp the armors of the cable.
Power supply unit PSU-007
2.6
Changing AC Power Specification of Processor
Unit
To change AC power specification between 100 VAC and 220 VAC, add or remove jumper
connector P108 on the PWR board 03P9339 and change the fuse on the processor unit
according to ship’s mains as shown in the table below. The figure on the next page shows
the location of the fuse and the jumper connector on the PWR board. Also, adjustment of
the overvoltage detection circuit is required.
Note: To change from 220VAC to 100VAC, locally prepare the jumper connector, referring to
the figure on the next page (VH8P connector housing is fitted at J108).
2-12
Power supply
Fuse
Jumper connector P108
100 VAC
10A
Added
220 VAC
5A
Removed
2. WIRING
Cover of PWR board
Fuse
PWR board
Upper part of processor unit
(SPU assembly omitted)
J105
PWR board
J106
(P)HV
J104
J103
R21
(OVER)
P108/J108
J101
AC FIL
87654321
Jumper connector
(VH8P)
How to adjust the overvoltage detection circuit:
1. Add or remove the jumper connector P108 and change the fuse.
2. Rotate R21 fully clockwise on the PWR board.
3. Connect a variable transformer between ship's mains and the input power terminal board
TB-1 of the processor unit.
4. Adjust the variable transformer output (i.e., input voltage to the processor unit) as follows.
For 100 VAC set: 144 VAC
For 220 VAC set: 288 VAC
5. Turn on the radar and rotate the R21 counterclockwise gradually until the overvoltage
detection circuit functions (i.e., power supply cuts off).
6. Lower the output voltage of the variable transformer and confirm that the radar
automatically turn on with a voltage lower than 142VAC or 284VAC.
7. Gradually increase the output voltage of the variable transformer and confirm that the
overvoltage detection circuit functions at 144V or 288VAC of the variable transformer
output.
8. Assemble and connect the processor unit.
2-13
2. WIRING
This page is intentionally left blank.
2-14
3. SETTING AND ADJUSTMENT
3.1
DIP Switch Setting
The processor unit is shipped for model FAR-2137S. If your model is FAR-2837S/2137S-BB,
change the DIP switch setting as follows.
1. Remove the top cover of the processor unit.
2. Open the SPU assembly block and remove the shield cover.
Shield cover
SPU assembly block
SPU board 03P9337
DIP switch S1
3. Set the DIP switch S1 as follows.
OFF
1
ON
S1
Monitor SXGA for
FAR-2137S
(Default)
1
2
3
4
OFF
OFF
2
3
4
S1
Monitor UXGA for
FAR-2837S (For
MU-231CR
S. No. 0269 and later)
ON
OFF
FAR-2137S-BB
OFF
ON
Not used.
Note: Set #1 and #2 of S1 to OFF for MU-231CR S. No. 0268 and earlier.
3-1
3. SETTING AND ADJUSTMENT
3.2
Initializing Tuning
1. Transmit the radar on 48 nm range and rotate the GAIN knob to show 70-80 of the gain
bar.
2. Roll the trackball to choose the MENU box at the right side of the screen and then push
the left button.
3. Roll the wheel to choose 1 ECHO and then push the wheel.
[ECHO]
1 BACK
2 2ND ECHO REJ
OFF/ON
3 TUNE INITIALIZE
4 PM
OFF/ON
5 SART
OFF/ON
6 WIPER
OFF/1/2
7 ECHO AREA*
CIRCLE/WIDE/ALL
8 [PICTURE SELECT]
9 STC RANGE
+00
Bold: Default settings
(Same for all menu illustrations)
*: non IMO-type only.
ECHO menu
4. Roll the wheel to choose 3 TUNE INITIALIZE.
5. Push the wheel to initialize automatic tuning.
After a while, echoes appear on the screen. The message “TUNE INITIALIZE” appears in
red during automatic tuning. When this message disappears, the tuning is completed. If
necessary adjust the GAIN to show echoes clearly.
6. Push the right button twice to close the menu.
3-2
3. SETTING AND ADJUSTMENT
3.3
Heading Alignment
You have mounted the antenna unit facing straight ahead in the direction of the bow.
Therefore, a small but conspicuous target dead ahead visually should appear on the
heading line (zero degrees).
In practice, you will probably observe some small bearing error on the display because of
the difficulty in achieving accurate initial positioning of the antenna unit. The following
adjustment will compensate for this error.
Correct bearing
relative to heading
α
Target
340
350
α
000
010
020
330
030
320
040
310
050
060
300
070
290
280
080
270
090
260
100
250
110
240
120
230
130
140
220
210
150
200
190
180
160
170
Picture appears
deviated clockwise.
Antenna mounted error
to port (HDG SW
advance)
β
Apparent position
of target
β
Target
340
350
000
010
020
330
030
320
040
310
050
060
300
070
290
280
080
270
090
260
100
250
110
240
120
230
130
140
220
210
150
200
Antenna mounted error
to starboard (HDG
SW delayed)
Apparent
position
of target
190
180
170
Correct
bearing
relative to
heading
160
Picture appears
deviated counterclockwise.
Heading alignment
1. Select a stationary target echo at a range between 0.125 and 0.25 nm, preferably near
the heading line.
2. Operate the EBL control to bisect the target echo.
3. Read the target bearing.
4. Measure the bearing of the stationary target on the navigation chart and calculate the
difference between actual bearing and apparent bearing on the radar screen.
5. Press the [MENU] key to show the main menu.
6. While pressing and holding down the [HL OFF] key, press the [MENU] key five times.
3-3
3. SETTING AND ADJUSTMENT
7. Press [0] key to show the [INITIALIZE] menu.
[INITIALIZE]
1
2
3
4
5
6
7
8
9
BACK
[ECHO ADJ]
[SCANNER]
[INSTALLATION]
[OWN SHIP INFO]
[TT PRESET]
[NETWORK]
[OTHER]
[FACTORY]
Note: See next page to access the INITIALIZE menu with the trackball style control unit
RCU-015.
8. Press [2] key to open the [ECHO ADJ] menu.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
9. Press [3] key to choose the HD ALIGN option.
10. Key in the bearing difference. The setting range is 0 to 359.9°
11. Confirm that the target echo is displayed at correct bearing on the screen.
12. Press the [MENU] key to finish.
3-4
3. SETTING AND ADJUSTMENT
How to Access the Installation Mode with the RCU-015 Trackball Style
Controller
1. By using the trackball,
move the pointer until
it highlights the MENU
box as shown. DO
NOT CLICK the menu
box, just leave the
arrow over the menu.
2. Press and hold down
the F1 key. Keep it
held down during the
next step.
3. Then, click on the right
controller button 5 times.
You should hear a “triple
Beep” on the fifth press.
The INITIALIZE menu will
appear. Click on
INSTALLATION to access
the installation menus.
3-5
3. SETTING AND ADJUSTMENT
3.4
Adjustment Sweep Timing
Sweep timing differs with respect to the length of the signal cable between the antenna unit
and the processor unit. Adjust sweep timing at installation to prevent the following
symptoms:
• The echo of a “straight” target (for example, pier), on the 0.25 m range, will appear on the
display as being pulled inward or pushed outward. See Figure below.
• The range of target echoes will also be incorrectly shown.
(1) Correct
(2) Target pushed
inward
(3) Target pushed
outward
Examples of correct and incorrect sweep timings
1.
2.
3.
4.
Transmit on the 0.25 nm range.
Adjust radar picture controls to display picture properly.
Select a target echo which should be displayed straightly.
Press [4] key to choose the [TIMMING ADJ] on the [ECHO ADJ] menu.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
5. Rotate the wheel to set a suitable value which causes the target to be displayed
straightly. The setting range is 0 to 4095.
6. Press the [MENU] key to finish.
3-6
3. SETTING AND ADJUSTMENT
3.5
Suppressing Main Bang
If main bang appears at the screen center, suppress it as follows.
1.
2.
3.
4.
Transmit the radar on a long range and then wait ten minutes.
Adjust gain to show a slight amount of noise on the display.
Select the 0.25 nm range. Adjust sea clutter to suppress.
Press [5] key to choose the MBS on the [ECHO ADJ] menu.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.00
4 TIMING ADJ
000
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
5. Rotate the wheel to set a suitable value so that the main bang disappears. The setting
range is 0 to 255.
6. Press the [MENU] key to finish.
3-7
3. SETTING AND ADJUSTMENT
3.6
Other Settings
ECHO menu setting
Open the [ECHO ADJ] menu as described on page 3-2.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
To close the menu, press the [MENU] key.
CABLE ATT ADJ
Before adjusting, set the radar as follows:
IR: 2, ES: off, EAV: off, 24nm range, long pulse
(Same as default setting of PICTURE1)
To adjust the cable attenuation manually, choose MANUAL by pressing [2] and the [ENTER]
key, and then rotate the wheel so that noise just appears on the screen when the gain is set
to 80. Default setting is 30 for the antenna cable length of 15m. The setting range is 0 to 73.
To adjust automatically, choose AUTO and press the [ENTER] key. The message “(CABLE
ATT ADJ” appears in red at the bottom of the screen. It takes about five minutes to
complete the adjustment, after which the exedra goes into stand-by.
DEFAULT ANT HEIGHT
Select height (m) of the radar antenna unit from the sea surface among 5, 7.5, 10, 15, 20,
25, 30, 35, 40, 45 and “more 50 m”.
NEAR STC CURVE, MID STC CURVE AND FAR STC CURVE
Use the default setting. Change the setting if desired according to sea condition.
RING SUPPRESSION
This is mainly used to removes “ring” noise which appears in the waveguide-type radar.
Adjust so the rings disappear at the range of 0.125 nm. The setting range is 0 to 255.
3-8
3. SETTING AND ADJUSTMENT
Scanner setting
1. Open the INITIALIZE menu described on page 3-3 and 3-4.
2. Press [3] key to open the SCANNER menu.
[SCANNER]
1 BACK
2 BLIND SECTOR 1
START 000°
ANGLE 000°
3 BLIND SECTOR 2
START 000°
ANGLE 000°
4 ANT REVOLUTION
LO/HI/AUTO
5 ANT SW
OFF/ON
6 ANT STOPPED
STBY/TX
7 M SPEC
OFF/ON
8 BB TYPE
NORMAL/BB
9 [DUAL RADAR]*
Note 1: Set the blind sector as minimum as possible.
Note 2: Do not set the blind sector in the bow direction.
*non IMO-type only
To close the menu, press the [MENU] key.
BLIND SECTOR 1 and BLIND SECTOR 2
Set area (up to 2) where no radar pulses will be transmitted, and the heading should be
adjusted before setting any sector. For example, set the area where an interfering object at
the rear of the scanner would produce a dead sector (area where no echoes appear) on the
display. To enter an area, enter start bearing relative the heading and dead sector angle. To
erase the area, enter 0 for both the START and ANGLE sections. The setting range of
START is 0 to 359° and ANGLE is 0 to 180°.
ANT REVOLUTION
Not used for FAR-2137S/2837S/2137S-BB.
ANT SW and ANT STOPPED
This is used for antenna maintenance by serviceman.
Note: Choose OFF at ANT SW to prevent the antenna rotation. As for ANT STOPPED,
choose STBY to prevent transmission while the antenna is stopped.
M SPEC and BB TYPE
Not used.
DUAL RADAR
See section 3.7.
3-9
3. SETTING AND ADJUSTMENT
INSTALLATION menu setting
Open the INSTALLATION menu by pressing [4] key on the INITIALIZE menu.
[INSTALLATION]
1 BACK
2 RADAR*
MAIN/SUB
3 RANGE UNIT **
NM/SM/km/kyd
4 RADAR NO***
1/2/3/4/5/6/7/8
5 RADAR POSN
FORE/MAIN TOP/
MAIN 2ND/MAIN 3RD/
AFT/PORT/
STAR BOARD
6 MODEL
6/12/25 UP/25 DOWN/
50/30 UP/30 DOWN/60
7 TYPE
IMO/A/B/C/W
8 ON TIME
XXXXXXX.X H
9 TX TIME
XXXXXXX.X H
0 PM GAIN ADJ
0
*: Cannot be selected.
**: non IMO-type only.
***: No.1-4: with antenna unit
No.5-8: without antenna unit
RADAR
Choose main radar or sub radar.
RANGE UNIT
Choose NM, SM, km or kyd (kilo yard) as appropriate, however-IMO type radar is “NM”
only.
RADAR NO and RADAR POSN
For multiple radar system using the network hub, set number (name) and antenna position
for each system to easily distinguish the radar configuration.
MODEL
Confirm the model of your radar. If the setting of this item is different from your model
(combination of the antenna unit), the radar functions abnormally.
Select “30 UP” for FAR-2137S/ 2837S/ 2137S-BB.
TYPE
Choose type of radar: IMO, A, B, C, or W.
3-10
3. SETTING AND ADJUSTMENT
ON TIME and TX TIME
These items show number of hours the radar has been turned on and transmitted,
respectively. Value can be changed; for example, after replacing magnetron TX Time can be
reset to 0.
PM GAIN ADJ
When you choose this item, the radar setting changes as follows.
RANGE:
24 NM
PULSE:
LONG
BLIND SECTOR:
OFF
STC:
OFF by Manual
RAIN:
OFF by Manual
ECHO STRECH:
OFF
ECHO AVERAGE:
OFF
VIDEO CONTRAST: 2-B
TUNE:
AUTO
1. Adjust the GAIN control so that a slight amount of white noise appears on the screen.
Arcs for performance monitor appear on the screen (Fig.1).
2. Adjust PM GAIN ADJ so that outer arc just disappears (Fig.2).
13.5 - 18.5 nm
13.5 - 18.5 nm
Approx. 0.6 nm
(10 dB)
Fig.1
Fig.2
3-11
3. SETTING AND ADJUSTMENT
OWN SHIP INFO menu setting
Open the OWN SHIP INFO menu by pressing [5] key on the INITIALIZE menu.
[OWN SHIP INFO]
1 BACK
2 LENGTH/WIDTH
LENGTH 100 m
WIDTH
50 m
3 SCANNER POSN
BOW 0 m
PORT 0 m
4 GPS1 ANT POSN
BOW 0 m
PORT 0 m
5 GPS2 ANT POSN
BOW 0 m
PORT 0 m
6 CONNING POSN
BOW 0 m
PORT 0 m
LENGTH/WIDTH and SCANNER POSN
To inscribe own ship shape on the screen when you choose it on the menu, enter length
and width of the ship and antenna position from the bow and left sides.
The setting ranges are as follows.
LENGTH:
0 to 999 m
WIDTH:
0 to 999 m
BOW:
0 to 999 m
PORT:
0 to 999 m
GPS 1 ANT POSN and GPS 2 ANT POSN
These items are needed for AIS information. Enter the GPS antenna position from the bow
and left sides. The setting ranges are the same as above.
CONNING POSN
Enter the conning position in the wheelhouse, from the bow and left sides. The setting
ranges are the same as above.
When you set the display reference point to the conning position, these values are used to
correct the radar antenna position.
Note: When two or more radars are installed, items other than 3 SCANNER POSN should
be the same on each radar.
3-12
3. SETTING AND ADJUSTMENT
TT PRESET menu setting
Open the TT PRESET menu by pressing [6] key on the INITIALIZE menu.
[TRACK PRESET]
[TT PRESET]
1 BACK
2 TT DATA OUTPUT
OFF/TTM/TTD
REL/TRUE
4800/9600/
19200/38400
3 MAX RANGE
24/32
4 ECHO LEVEL
16
5 QV DISPLAY
OFF/ON
6 TT W/O GYRO*
OFF/ON
7 [TT PRESET]
8 [TRACK PRESET]
9 [TT SENSOR DATA]
0 DEFAULT
[TT PRESET]
1 BACK
2 LAND SIZE
1200 M
3 ANT SELECT
XN12AF/XN20AF/
XN24AF/XN4A/XN5A
SN30AF/SN36AF/
SN4A/SN5A
4 AUTO ACQ CORRE
5 SCAN
5 AUTO ACQ WEED
1 SCAN
6 [TT DETAIL DATA]
1 BACK
2 GATE SIZE
S/ M /L/LL
3 FILTER RESPONSE
1/ 2 /3/4
4 LOST COUNT
9 SCAN
5 MAX SPEED
100 KTS
6 TRACKING MODE
1 /2/3/4
7 START TIME TGT VECT
TIME /SCAN
50 SEC
20 SCAN
*: Not on IMO radar
TT DATA OUTPUT
Set the output format from J619 port (sentence, bearing and baud rate) of tracked targets.
Sentence:
(OFF: No output, TTM: Tracked target information, TTD: Tracked target data)
Bearing:
REL: Target bearing from own ship, degree relative,
Target course, degree relative.
TRUE: Target bearing, degree true, target course, degree true.
Baud rate:
(4800, 9600, 19200 or 38400 bps)
NOTE: The TT DATA OUTPUT port changes according to the setting for INS as described
on page 3-15.
INS-OFF:
Output from J619 port only
INS-SERIAL: Output from J619 and J620 (TTM only) ports
INS-LAN:
Output from J619 and NETWORK (TTM only) ports
MAX RANGE
Choose the ARPA tracking range, 24 or 32 nm.
ECHO LEVEL
Set the detection level of echoes. The setting range is 1 to 31.
QV DISPLAY
OFF: Normal picture
ON: Quantized picture; always off at power on
3-13
3. SETTING AND ADJUSTMENT
TT W/O GYRO (Not on IMO radar)
If a gyrocompass is not connected, choose the TT function, ON(working) or OFF (no
working).
LAND SIZE
Set the land size in units of 100 m. The setting range is 100 to 1000 m.
ANT SELECT
Set the antenna radiator type of your radar.
AUTO ACQ CORRE
Set the correlation count of automatic acquisition. The setting range is 3 to 10.
AUTO ACQ WEED
Set the cancel count of automatic acquisition. The setting range is 1 to 5.
GATE SIZE
Set the gate size among S, M, L, or LL.
FILTER RESPONSE
Set the filter response function. The setting range is 1 to 4.
LOST COUNT
Set the lost count. The setting range is 1 to 20.
MAX SPEED
Set the maximum tracking speed. The setting range is 40 to 150.
TRACKING MODE
Set the tracking mode among 1 to 4.
START TIME TGT VECT
Choose time which a vector appears after acquisition, TIME or SCAN and set seconds or
scan counts.
3-14
3. SETTING AND ADJUSTMENT
OTHER menu setting
Open the OTHER menu by pressing [8] key on the INITIALIZE menu.
[OTHERS]
1
2
3
4
5
BACK
DEMO ECHO
OFF/EG/TT-TEST/PC
EAV W/O GYRO
OFF/ON
TT CATEGORY SELECT
CAT1/CAT2 3
INS
OFF/SERIAL/LAN
EAV w/o GYRO
If a gyrocompass is not connected, choose the echo average function, ON (working) or OFF
(no working).
TT CATEGORY SELECT
Choose CAT1 or CAT2▪3 depending on your ship size.
CAT1: All ships over than 10,000 GT
CAT2: All ships between 500 and 10,000 GT
CAT3: All ships less than 500 GT
INS
Choose appropriate item according to the ECDIS connected.
OFF:
No connection
SERIAL: When connecting FEA-2105 series ECDIS.
LAN:
When connecting FEA-2107 series ECDIS.
3-15
3. SETTING AND ADJUSTMENT
3.7
Dual Radar Display (non IMO-type only)
The image from two or more radars may be shown together on one radar display. This
allows you to take advantage of the best characteristics radars has to offer.
Image from main radar
Image from
external radar
Separate internal and external
images ("COMBINE" setting)
The following should be done in order to enable the dual radar display:
• Set antenna position correctly on both the main radar and the external radar.
•
Select external radar to use, from the DUAL RADAR menu. (See paragraph
3.7.3.)
3.7.1
Enabling/Disabling the Dual Radar Display
Enable or disable the dual radar display as shown in this section.
Note 1: The Tx blanking sector boundary lines are not shown when the dual radar display is
active. Further, neither the internal or external image is shown in the Tx blanking
sector.
Tx blanking sector
Tx blanking sector is not shown.
No image in Tx blanking sector.
Display area
Tx blanking sector
3-16
Dual radar display with
Tx blanking sector
3. SETTING AND ADJUSTMENT
Note 2: In the dual radar display, a guard zone set on the main radar is also accommodated on
the external radar. When the position of the antennas for the main and external radars
is different and the No. 2 guard zone is set on a close-in range, the on-screen guard
zone may be shifted slightly from both the main radar antenna reference and external
radar antenna reference. Accordingly, on the dual radar display, the actual guard zone
area may be shifted slightly. For example, the guard alarm sounds against a target
which has almost entered the guard zone. The further the range the smaller the shift;
however, there is little shift with the No.1 guard zone (3-6 mile range, fixed). Further, do
not set a guard zone such that it straddles a boundary line of the dual radar sector.
A guard zone cannot be set while the dual radar display is active. Set a zone before activating
the dual radar display.
1. Open the INITIALIZE menu. See page 3-4.
2. Press the [3] key to show the SCANNER menu.
3. Select 9 [DUAL RADAR] and push the left button.
[DUAL RADAR]
1 BACK
2 DUAL RADAR
OFF/ COMBINE
3 COMBINE MODE
OWN/EXT
4 COMBINE SECTOR
START 000°
ANGLE 000°
5 COMBINE RANGE
START
00.00NM
LENGTH 00.00NM
6 EXT RADAR
1/2/3/4
4. Select 2 [DUAL RADAR] and push the left button.
5. Select OFF or COMBINE as appropriate and push the left button. For COMBINE, the
ANTENNA box at the top left-hand side becomes gray.
OFF:
Turn off the dual radar display.
COMBINE: Display a part of the external radar image in the window on the main radar.
3-17
3. SETTING AND ADJUSTMENT
Push the right button four times to close the menu.
Note 1: The dual radar function becomes inoperative when the external radar is turned off, set
to stand-by, or set as sub display. When this happens, the buzzer sounds and the
message "EXT RADAR STBY" (power off, stand-by only) appears.
Note 2: The dual radar display is inoperative on the stern-up and shuttle ferry modes.
Note 3: Some functions of the external radar image, listed below, may be adjusted from the
main radar.
1) Left-click the radar selection indication "CTRL OWN" at the top-left side of the screen to
switch control to the external radar. The indication then shows "CTRL EXT". Each click of
the indication switches control between the main and external radar alternately.
2) The external image may be adjusted from the main radar. The following functions may be
adjusted:
·Transmit/stand-by switching
·PICTURE box setting
·GAIN
·A/C SEA
·A/C RAIN
·Tuning
·ECHO menu setting (2nd trace echo rejector, performance monitor)
·Range scale
·TT functions.
·CPA/TCPA box settings
3-18
3. SETTING AND ADJUSTMENT
3.7.2
Specifying Sector Width and Length
When 2 DUAL RADAR in the DUAL RADAR menu is set for "COMBINE", specify
the width and length of the sector from the external radar to display on own radar.
1. Open the INITIALIZE menu.
2. Press the [3] key to show the SCANNER menu.
3. Select 9 [DUAL RADAR] and push the left button.
4. Select 3 COMBINE MODE and push the left button.
5. Select OWN or EXT and push the left button.
a)
OWN:
Set own radar’s antenna as reference point and set display
area of own radar. The area outside that set here is where the image
from the external radar will be displayed.
b)
EXT:
Set external radar’s antenna as reference point and set
display area of external radar. The area outside that set here is where
the image from own radar will be displayed.
Radar selected for COMBINE: External
START:
315 degrees
ANGLE: 90 degrees
START:
00.00 nm
LENGTH: 99.99 nm
Radar selected for COMBINE: Own
START:
45 degrees
ANGLE: 270 degrees
START:
00.00 nm
LENGTH: 99.99 nm
Picture from
external radar
Position of antenna
for external radar
Position of antenna
for own radar
Picture from
own radar
6. Select 4 COMBINE SECTOR and push the left button.
3-19
3. SETTING AND ADJUSTMENT
7. Use the scrollwheel to set START and ANGLE, referring to the description and
example below. Spin the scrollwheel to set and push it to confirm.
c) A solid green line marks the dual radar display area.
• START: Start point of the sector (in degrees, 000-359)
• ANGLE: Width of the sector (in degrees, 000-359)
d)In the example below, START is 130° and ANGLE is 100°.
Width of sector
ANGLE
(Example: 100°)
START
(Example: 130°)
8. Select 5 COMBINE RANGE and push the left button.
9. Use the scrollwheel to set START and LENGTH, referring to the example below.
Spin the scrollwheel to set and push it to confirm.
• START:
Set range start point.
• LENGTH: Set length of sector.
START
LENGTH
Example:
START:
01.00 nm
LENGTH: 02.00 nm
Push the right button four times to close the menu.
3-20
3. SETTING AND ADJUSTMENT
3.7.3
Choosing External Radar (image source)
Select the external radar to use in the dual radar display.
1. Open the INITIALIZE menu.
2. Press the [3] key to show the SCANNER menu.
3. Select 9 [DUAL RADAR] and push the left button.
[DUAL RADAR]
1 BACK
2 DUAL RADAR
OFF/ COMBINE
3 COMBINE MODE
OWN/EXT
4 COMBINE SECTOR
START 000°
ANGLE 000°
5 COMBINE RANGE
START
00.00NM
LENGTH 00.00NM
6 EXT RADAR
1/2/3/4
4. Select 6 EXT RADAR and push the left button.
5. Select desired radar no. and push the left button.
Only the numbers of connected radars are valid. Radar no. is set on the Installation Setting
menu.
6. Press the [MENU] key to close the menu.
3-21
3. SETTING AND ADJUSTMENT
This page is intentionally left blank.
3-22
4. INSTALLING OPTIONAL
EQUIPMENT
4.1
Gyro Converter GC-10
The Gyro Converter GC-10, incorporated inside the processor unit, converts analog
gyrocompass reading into digital coded bearing data for display on the radar screen.
This section explains how to install the GC-10 (mainly consisting of the GYRO
CONVERTER board) and set it up according to gyrocompass connected.
Installing the GYRO CONVERTER board
Necessary Parts: GC-10-2 (Code number 000-080-440)
See packing list for details at the back of this manual.
1
3
1
12
3
1
4
1. Open the processor unit.
2
1
1
12
1
1
1
5
1
1
3
7
Processor unit (Opened)
4-1
4. INSTALLING OPTIONAL EQUIPMENT
2. Fasten the GYRO CONVERTER board in the processor unit with five washer head
screws and male connector 231-607/019-FUR (called J602) with two screws.
Screw M3X8 5 pcs
(Torque 0.78Nm)
GYRO CONVERTER board
64P1106A
Screw M2.6X10 2 pcs
(Torque 0.39Nm)
1
7
Connector (231)
231-107/026-FUR
7
1
Connector (231)
231-607/019-FUR
Attaching GYRO CONVERTER board in the processor unit
3. Connect the GYRO CONVERTER board and the 03P9342 board with connector
assemblies 03-2088 and 03-2091.
4-2
4. INSTALLING OPTIONAL EQUIPMENT
4. Connect the GYRO CONVERTER board and J602 with two connector assemblies
03-2089 and 03-2090.
Wiring for WAGO connector
Press downward.
Terminal opener
Connection for J602
J602
P608
1 2 3 4
7 6 5 4 3 2 1
PPL
BLU
GRN
YEL
ORG
From J5 RED
BRN
YEL
ORG
RED
BRN
WAGO connector
Twist
Wire
Procedures
1. Twist the cores
2. Press the terminal opener downward.
3. Insert the wire to hole.
4. Remove the terminal opener.
5. Pull the wire to confirm that it is
secure.
2 VH connector assy.
03-2089 (5P)
2 VH connector assy.
03-2090 (3P)
1 NH connector assy.
03-2091 (5P)
To J602
P5
XH-PH connector assy.
03-2088 (6-14P)
To P608
P7
P4
P1
P603
J5
4
GYRO CONVERTER J1
64P1106A
J4
1
1
3
P608
3
12
1
J7
J602
1
12
1
1
1
2
1
7
J603
5
From J4
Connection for P608
1
1
2
TB
03P9342
Connecting connector assemblies
4-3
4. INSTALLING OPTIONAL EQUIPMENT
5. Confirm gyrocompass specifications and set up the DIP switches and jumper wires on
the GYRO CONVERTER board according to gyrocompass connected:
• Setting jumper wires and DIP switches by gyrocompass specifications: page 4-5
• Setting jumper wires and DIP switches by make and model of gyrocompass: page 4-7
• Location of jumper wires and DIP switches: page 4-8
6. Pass gyrocompass cable through the cable clamp and connect it to connector J602 as
shown in the figure on page 4-3.
7. Attach the clamps on the plastic cover and then attach the cover to the chassis as
shown in the figure below. Insert cables to the clamp ED-1, respectively.
Screw M4X8 3 pcs
(Torque 0.98Nm)
Plastic cover
Clamp CKS-10-L
Clamp EDS-1
Insert cables to these
clamp.
2
1
12
1
1
1
5
1
1
1
7
3
1
3
1
12
3
1
4
Clamp CKS-13-L
Attaching plastic cover for GYRO CONVERTER board
8. Close the processor unit.
4-4
4. INSTALLING OPTIONAL EQUIPMENT
Connection of external power supply
An external power supply is necessary when the repeater signal is step-by-step type and
the step voltage is below 20 V or output voltage is less than 5 W.
1. Cut jumper wire JP1 on the GYRO CONVERTER board when an external power supply
is used.
2. Connect gyro cable and power cable as shown below.
GYRO CONVERTER board
[A] 64P1106
External Power Supply
20 - 135 VAC
20 - 100 VDC
J5
1 > R2
2 > R1/COM
Either connection
in case of DC
polarity.
S2
J4
1 > S1
2 > S2
S3
3 > S3
S1
Gyrocompass
(Step type)
COM
F.G.
4>T
5 > F.G.
Connection of external power supply to GYRO CONVERTER board
DIP switch, jumper wire settings
Default setting
The gyro converter GC-10 is set at the factory for connection with the gyrocompass
specifications below.
AC synchronous signal: 50/60 Hz
Rotor voltage: 60 V to 135 V AC
Stator voltage: 60 V to 135 V AC
Gear ratio: 360x
Supply voltage: 30 V to 135 V AC
If the specifications of the gyrocompass differ from those mentioned above, change jumper
wire and DIP switch settings on the GYRO CONVERTER board. Settings may be changed
according to gyrocompass specifications (see page 4-6) or make and model of
gyrocompass (see page 4-7). For the location of DIP switches and jumper wires, see page
4-8.
Note: If you change the setting with power supplied, set #8 of SW2 from OFF to ON, then
OFF again.
4-5
4. INSTALLING OPTIONAL EQUIPMENT
Setting method 1: DIP switch settings and gyrocompass specifications
1) Gyrocompass type
2) Frequency
Gyrocompass
type
SW
1-4
SW
1-5
SW
1-6
JP1
SW
1-7
SW
1-8
AC
synchronous
OFF
OFF
OFF
#1, #2,
#3
50/60 Hz
OFF
OFF
AC synchronous
pulsating current
DC
synchronous
OFF
OFF
OFF
#2, #3,
#4
400 Hz
ON
OFF
AC synchronous
pulsating current
DC step
ON
OFF
OFF
#4, #5,
#6
500 Hz
OFF
ON
AC synchronous
pulsating current
Full-wave
pulsating current
OFF
ON
OFF
#4, #5,
#6
DC
ON
ON
DC synchronous
DC step
Half-wave
pulsating current
ON
ON
OFF
#4, #5,
#6
3) Rotor Voltage (between R1 & R2)
Rotor Voltage
SW
2-1
JP3
20 to 45 VAC
ON
30 to 70 VAC
Frequency
Remarks
4) Stator Voltage (between S1 & S2)
Stator
Voltage
SW
2-2
SW
2-3
JP2
#2
20 to 45 VAC, or
20 to 60 VDC
ON
OFF
#2
OFF
#2
30 to 70 VAC, or
40 to 100 VDC
OFF
OFF
#2
40 to 90 VAC
ON
#1
40 to 90 VAC
ON
OFF
#1
60 to 135 VAC
OFF
#1
60 to 135 VAC
OFF
OFF
#1
5) Ratio
6) Supply Voltage
Ratio
SW
1-1
SW
1-2
SW
1-3
Stator
Voltage
360X
OFF
OFF
OFF
180X
ON
OFF
OFF
90X
OFF
ON
OFF
36X
ON
ON
OFF
JP4
JP5
20 to 45 VAC, or 20 to 60 VDC
#2
#2
30 to 70 VAC, or 40 to 100 VDC
#1
#1
7) AD-10 format data
Tx interval
8) NMEA-0183
Tx interval and Output sentence
Select data transmitting interval for ports 1 to 6 with jumper
wires JP6 and JP7: #25 for 25 ms, #200 for 200 ms.
Tx
interval
Note: The Tx interval is available in 25 msec or 200 msec.
Use 25 msec for radar.
9) NMEA-0183
Version no.
10) NMEA-0183
Baud rate
SW
2-5
SW
2-6
1s
OFF
OFF
HDT+VHW
200 ms
ON
OFF
HDT
100 ms
OFF
ON
HDT
25 ms
ON
ON
HDT
11) Power fail
detection
Version no.
SW3-1
Baud rate
SW3-2
Talker
SW3-3
1.5
OFF
4860bps
OFF
Disable
OFF
2.0
ON
38400bps
ON
4-6
Output
sentence
Enable
ON
(Use OFF for radar.)
12) Stator signal
breaking detection
Detection
SW2-7
Execute
OFF
No execute
ON
SW2-4: factory use only
SW3-4: not used
4. INSTALLING OPTIONAL EQUIPMENT
Setting method 2: by make and model of gyrocompass
Maker
Models
Specification
SW
1-1
SW
1-2
SW
1-3
SW
1-4
SW
1-5
SW
1-6
SW
1-7
SW
1-8
SW
2-1
SW
2-2
SW
2-3
JP 1
JP 2
JP 3
JP 4
JP 5
Anschutz
Standard 2,3
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 22V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
#1,
#2,#3
#2
#2
#1
1
#
Standard 4,6
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 90V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#2
#1
#1
1
#
Standard 20
DC step
35V 180x
COM(-) ,3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
2
#
C-1/1A/2/3
A-55, B-55
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 22V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
#1,
#2,#3
#2
#2
#1
1
#
CMZ-700
DC step
24V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF Remove
#2
-
*
*
DC synchronous 360x
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
-
ON
OFF
Remove
#2
-
*
*
DC step
35V 180x
COM(+),3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
AC synchronous
50/60Hz
Rotor voltage: 100V
Stator voltage: 90V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
step
35V 180x
See note below. COM(+),3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
Remove
#2
-
*
*
Plaith
NAVGAT II/III
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 68V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#2
#2
#1
#1
Tokimec
(Sperry
type)
ES-1/2/11
GLT-101/102/
103/106K/107
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 90V
36x
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
ES-11A/110
TG-200
PR222R/2000
PR237L/H
GM 21
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 22V
90x
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
MK-14
MOD-1/2/T
NK-EN,NK-EI
DC step
70V 180x
COM(-), 3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
SR-130/140
DC step
70V 180x
5-wire, open collector
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
TG-100/5000
PR-357/130/
140, ES-17
GLT-201/202
/203
DC step
70V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
TG-6000
DC step
24V 180x
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
GM-11
AC synchronous
50/60Hz
Rotor voltage: 100V
Stator voltage: 90V
90x
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
SR-120,ES-16
MK-10/20/30
DC step
35V 180x
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
Kawasaki
GX-81
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 90V
90x
OFF
ON
OFF OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
Armabrown
MK-10,MKL-1
SERIES1351,
MOD-4
DC step
50V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
Robertson
SKR-80
DC step
35V 180x
COM(-), 3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
Yokogawa
Navtec
(Plaith
type)
CMZ-250X/
300X/500
CMZ-100/200/
300
C-1Jr,D-1Z/1/3
IPS-2/3
CMZ-50
OFF
OFF
*: Set JP4 and JP5 according to the voltage of the external power supply.
Note: If CMZ-50 has 35VDC, set JP1 to #4, #5, #6.
4-7
4. INSTALLING OPTIONAL EQUIPMENT
Location of DIP switches, jumper wires on the GYRO CONVERTER board
JP5, JP4
(Supply voltage)
JP2
(Rotor voltage)
JP3
(Stator voltage)
SW3
DIP switch
J12
(Data output
port #6)
J11
(Data output
port #5)
J10
(Data output
port #4)
64P1106
JP1
(Gyro type)
SW2
DIP switch
Fuse
(2A)
SW1
J4
DIP switch
(Stator signal input)
J5
(Rotor signal input,
external power input)
J6
(IEC-61162-1 output port)
JP6, JP7
(AD format
data Tx interval)
J9
(Data output port #3)
J8
(Data output port #2)
J7
(Data output port #1)
GYRO CONVERTER board
Setting the heading readout on the radar display
Confirm that the gyrocompass is giving a reliable readout. Then, set the heading readout on
the radar display with the gyrocompass readout as follows:
1. Roll the trackball to place the arrow in the HDG box at the top right corner of the screen.
2. Push the right button on the trackball module to open the HDG menu.
[HDG MENU]
1 HDG SOURCE
AD-10/SERIAL
2 GC-10 SETTING
000.0˚
HDG menu
3.
4.
5.
6.
Press the [1] key to choose the HDG SOURCE and choose AD-10.
Press the [2] key to choose the GC-10 SETTING option.
Roll the wheel to set gyrocompass reading.
Press the [MENU] key to close the menu.
4-8
4. INSTALLING OPTIONAL EQUIPMENT
4.2
Memory Card Interface Unit
Mounting considerations
When selecting a mounting location, keep in mind the following points:
•
Locate the memory card interface unit away from heat sources because of heat that can
build up inside the cabinet.
•
Locate the unit away from places subject to water splash and rain.
•
Leave sufficient space at the sides and rear of the unit to facilitate maintenance.
•
A magnetic compass will be affected if the unit is placed too close to the magnetic
compass. Observe the compass safe distances on page ii to prevent deviation of a
magnetic compass.
Flush mounting
This unit can be flush-mounted in a panel with the standard installation materials.
1. Prepare a cutout in the mounting location, referring to the outline drawing at the end of
this manual.
2. Screw in the threaded rods to the flange of the front panel of the unit securely by hands.
3. Set the unit to the cutout.
4. Insert the flat washer, spring washer and nut in that order for each rod and fasten the
nuts.
Flush mounting
4-9
4. INSTALLING OPTIONAL EQUIPMENT
Desktop mount
For desktop mount, the optional desktop mount kit FP03-10201 is required. Refer to the end
of this manual.
1. Fix the mounting bracket 19-023-3081 on the unit with four screws.
2. Mount the above assembly on a desktop with four tapping screws.
Console mount
For console mount, the optional console mount kit FP03-10202 is required. Refer to the end
of this manual.
1. Fix the mounting bracket 19-023-3091 on the unit with four screws.
2. Mount the above assembly to the console with four sets of nut, spring washer and flat
washer.
Connection
1) Connection between one processor unit and one memory card IF unit
Connect as shown in the figure below.
Processor unit
J614
12 VDC
MJ-A3SPF0015-100 (10 m)
Memory card IF unit
12 VDC
two mini-cards
PSE-4PTX-BL (10 m)
NETWORK
NETWORK
RJ-45
2) Connection between one memory card IF unit and multiple processor units
Prepare optional LAN cable kit and switching hub HUB-100. Connect as shown in the next
page. Set the radar number on the INSTALLATION menu (see page 3-10), and then turn the
power off and on.
LAN cable kit
Type
Code No.
Contents
OP03-28900
000-082-658
Cable FR-FTPC-CY (10 m), Modular connector 2 pcs.
OP03-28910
000-082-689
Cable FR-FTPC-CY (20 m), Modular connector 2 pcs.
OP03-28920
000-082-660
Cable FR-FTPC-CY (30 m), Modular connector 2 pcs.
4-10
4. INSTALLING OPTIONAL EQUIPMENT
No.1
J614
Processor
unit
NETWORK
Memory card IF unit
MJ-A3SPF0015-100 (10 m)
12 VDC
FR-FTPC-CY (10/20/30 m)
(straight)
two mini-cards
NETWORK
FR-FTPC-CY (10/20/30 m)
(straight)
No.2
Processor
unit
No.3
Processor
unit
No.4
Processor
unit
Switching hub
FR-FTPC-CY
(10/20/30 m)
(straight)
HUB-100
(option)
FR-FTPC-CY (10/20/30 m) (straight)
FR-FTPC-CY (10/20/30 m) (straight)
Note: When two memory card interface units are connected via network, change ID code
for the second unit.
1. Remove the cover and set IP0 bit of the DIP switch S1 to ON on the CARDCPU board
03P9333.
2. Set INIT bit of S1 to ON and turn on the power of the radar. Wait till CR2 starts blinking.
Never turn off the power until CR2 starts blinking.
3. Turn off the power and set INIT bit to OFF.
ON
J314
OFF
IP0
IP1
IP2
CR2
S1
INIT
(Default: all OFF)
CARDCPU board 03P9333
4-11
4. INSTALLING OPTIONAL EQUIPMENT
4.3
DVI-RGB Conversion Kit (for VDR connection)
This information provides the procedure necessary for the installation of the DVI-RGB
conversion kit. This kit is installed in the processor unit to enable connection of a VDR
(Voyage Data Recorder) or RGB monitor to record radar pictures into a VDR. When
changing the D-sub 15P of the RGB cable to the BNC connector, use the BNC connector
converter described on page 4-15. This RGB output complies with the image test defined in
the VDR test standard, IEC 61996.
Name:
Type:
Code no.:
Resolution:
DVI-RGB conversion kit
OP03-180-2
008-536-070
Outputs RGB with the resolution of DVI input.
Display unit
Resolution
DIP switch setting (S-1#1)
MU-201CR
1024x1280
OFF
MU-231CR
1024x1365
ON
Output signal specification:
Video; 0.7Vp-p, 75Ω termination, positive polarity
Horizontal sync signal; TTL level, negative polarity
Vertical sync signal; TTL level, negative polarity
See packing list for contents. Refer to the figure below for modification.
DVI-RGB Conversion board
(SLB-FRN4-A)
DVI cable
M3x8
6 pcs
J9
(10 pin)
J4
(6 pin)
DVI video input
J3
J615
03-2092
03-2094
03P9342 board
03-2093
SQ-35
Spacer
6 pcs
M3x8
4 pcs
J1
(13 pin)
J3
(3 pin)
RGB-BUFF board*
(03P9229B)
D-sub 15P
Female
J2
RGB Cable
(User supply)
Spring washer
Fixing
holes
Boss
RGB video output
Ferrite core
Clamp copper tape
section by cable clamp.
To external RGB monitor or
BNC connector converter
for VDR connection (see
page 4-17).
Ferrite core side: Connect to DVI-D port on
the upper part of the processor unit.
*Indepent of the MAIN board.
4-12
4. INSTALLING OPTIONAL EQUIPMENT
1.
Remove the top cover and open the upper part of the processor unit.
DVI-D port
(Connect DVI cable at step 13)
Processor unit
2. Fix the 03P9229A board (RGB-BUFF) with four screws. (See the figure below.)
3. Attach the connector assemblies to J1 and J3 on the 03P9229A board as follows.
J1:13-pin connector of the connector assembly 03-2094
J3:3-pin connector of the connector assembly 03-2093
4. Attach six sets of spring washers and spacers to the positions shown below.
Spring washer, spacer
J1
03P9229A board
J2 (Connect RGB Cable at step 11.)
J3
J2
03P9342 board
J615 (Connect connector assembies at step 9.)
Processor unit (Lower part)
5. Attach the DVI-RGB conversion board to the location shown in the figure on the next
page.
4-13
4. INSTALLING OPTIONAL EQUIPMENT
DVI-RGB
Conversion board
J3 (Connect DVI cable at step 10.)
J9
J4
Fixing the DVI-RGB conversion board
6. Attach the 10-pin connector from J1 on the 03P9229A board to J9 on the DVI-RGB
board.
7. Attach the connector assembly 03-2092 to J4 on the DVI-RGB conversion board.
8. Remove connector housing J615 from the 03P9342 board. Connect the cable from J3
on the 03P9229A board and the cable from J4 on the DVI-RGB conversion board to
J615. After connection, attach J615 to the 03P9342 board.
To connect wires to the connector housing, use the terminal opener (supplied as installation
materials) as shown below.
Terminal opener
J615 Housing
1Press downward
1
2
BRN
RED
ORG
YEL
GRN
2Insert core
Connecting wires to the housing
9. Connect the DVI cable to J3 on the DVI-RGB conversion board. Connect the end which
does not have the ferrite core.
10. Pass an RGB cable (local supply) through the cable clamp and connect it to J2 on the
03P9229A board.
11. Pass the DVI cable through the cable clamp, laying the section with copper tape in the
cable clamp.
12. Assemble the processor unit and connect the other end of the DVI cable to DVI-D port.
4-14
4. INSTALLING OPTIONAL EQUIPMENT
4.4 BNC Connector Converter
To connect the VR-5000 (FURUNO Voyage Data Recorder) to this radar, the DVI-RGB
conversion kit (mentioned at previous paragraph) and the BNC connector converter are
required. Also VGA cable (between the processor unit and the BNC connector converter)
and five 75 ohms coaxial cables (between the BNC connector converter and VR-5000) are
required.
FAR-2107
Processor Unit
BNC connector
converter
DSUB-BNC-1
VGA cable
DVI-RGB
Conversion kit
D-sub 15P
Female
D-sub 15P
Male
75 Ω coax. cable
VD1
R
R
G
G
B
B
H
HS
V
VS
VR-5000
Data collecting unit
Interconnection
4-15
4. INSTALLING OPTIONAL EQUIPMENT
4.5 Junction Box
Junction Box
If the length of the antenna cable is more than 100 m, the optional junction boxes are
required. These boxes should be mounted at the location protected because its
waterproofing is IPX3.
Antenna unit
Processor unit
RW-9600
(Max 15 m)
RW-9600
(Max 15 m)
DPYCY-6 (2 pcs.)
TTYCY-4 (1 pc.)
RG-12/UY (1 pc.) (Max 270 m)
Shipyard supply
Junction box
RJB-001
Junction box
RJB-001
Mounting
Fasten the junction boxes to the mounting location with four sets of M8 bolt and nut.
514
474
270
280
320
NAMEPLATE
139
60
Mass: 12kg
360
430
4-16
FIXING HOLES
4-φ10
4. INSTALLING OPTIONAL EQUIPMENT
Cable fabrication
RW-9600
5
20
approx. 450
Units: mm
Shield
Armor
Vinyl sheath
Pull out inner cables from here.
6
14 5 9
Shield
Coaxial cable
Crimp on lug for M8
DPYC-6 and TTYC-4
DPYC-6: approx. 130
TTYCY-4: approx. 150
φ = 13.9 mm
20
5
TTYCY-4 (Four twisted pairs)
DPYCY-6
φ = 17.7 mm
Armor
6
Sheath
Armor
Taper for unused wires.
Sheath
Conductor
S = 0.75 mm 2
φ = 1.11 mm
Conductor
S = 6 mm 2
φ = 3.12 mm
Vinyl sheath
Sheath
Armor
RG-12/UY
20
60
14 5 9
Inner conductor
Vinyl sheath
Armor
Outer conductor
4-17
4. INSTALLING OPTIONAL EQUIPMENT
Connection
Insert each cable to the cable gland as follows.
Cable gland
Flat washer
Vinyl sheath
Clamping gland
Gasket
Cut and trim armor.
Connect each cable cores to the terminal board, referring to the interconnection diagram on
next page.
Clamp outer conductor of coaxial cables.
Fix wires with cable-tie.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
RG12/UY
RG-12/UY
TTYCY-4
Connect inner conductors.
4-18
DPYCY-6
RW-9600
M8 screw for grounding
4. INSTALLING OPTIONAL EQUIPMENT
A-1
Antenna unit
03P9349
TB801
BRN
RED[B]
ORG[B]
YEL[B]
24V_PLUS 3
24V_MINUS 4
SPU_RF_D_A
SPU_RF_D_B
RF_SPU_D_A
RF_SPU_D_B
SIG-GND
GND
03P9342
RW-9600
TX-HV 1
N.C. 2
RW-9600
DPYCY-6
1
2
3
4
5
DPYCY-6
1
2
3
4
5
5
6
BLU[B]
GLY[B]
6
6
7
8
PPL[B]
WHT[B]
7
7
8 N.C.
9 N.C.
10
11
12
13
14
15 N.C.
8 N.C.
9 N.C.
10
11
12
13
14
15 N.C.
RED
GRN
BRK
WHT
GRN[B]
9
10
11
12
13
14
TB802
IF_VIDEO 1
GND 2
Processor unit
Junction box
Junction box
TTYCY-4
pair
pair
BRN
J613
1 TX-HV
2 N.C.
J610
ORG[B]
YEL[B]
BLU[B]
GLY[B]
PPL[B]
WHT[B]
RED
GRN
BRK
WHT
GRN[B]
RED[B]
1 24V_PLUS
2 24V_MINUS
3 MOTOR(+)
4 MOTOR(+)
5 MOTOR(-)
6 MOTOR(-)
7
8
9
10
11
12
SPU_RF_D_A
SPU_RF_D_B
RF_SPU_D_A
RF_SPU_D_B
SIG-GND
GND
J609
COAX
1
2
RG-12/UY
1
2
COAX
1 IF_VIDEO
2 GND
IV-1.25
Clamp with cable-gland.
4-19
4. INSTALLING OPTIONAL EQUIPMENT
This page is intentionally left blank.
4-20
5. INPUT/OUTPUT DATA
Input and output data are shown in the table below.
Note: This radar accepts position data fixed by WGS-84 geodetic datum only. Set the
datum to WGS-84 on the EPFS (GPS, etc.) connected to this radar. If other type of datum is
input, the error message "DATUM" appears and the AIS feature is inoperative. Baud rate for
the serial input is automatically set to 4800, 9600, 19200 or 38400 as appropriate.
Input
Data
Specifications
Contents
Remarks
Heading signal
synchro or step
GC-10 required
AD-10 format
External AD-100
AD-10 and
IEC 61162 are switched by
menu setting.
IEC 61162-2**
Speed signal
IEC 61162-1
Navaid data
IEC 61162-1
Position, course,
For IMO spec, IEC-61162-1
speed, waypoint,
Edition 2 is required.
route, time, wind data,
current data, depth,
temperature, roll, pitch
External radar
signal
Heading,
Bearing, Trigger,
Video
No STC control
Alarm ACK input
Contact closure
IEC61162-1
Track Control unit
Operate as remote display
Input from alarm system
ACK
RS-422
Input from alarm system
Option
Output
Data
Specifications
Contents
Remarks
Radar system data
RS-232C
RSD, OSD, TLL,
For PC plotter
TT data*
IEC 61162-1
TTD, TTM, TLB
For ECDIS
ALARM data
IEC 61162-1
ALR
For ALARM system
Remote display
signal
HD, BP Trigger,
Video
External LCD
monitor signal
DVI
Same as main display
unit
2 systems in total
External CRT
monitor signal
R, G, B, H, V
Same as main display
unit
Option
Alarm signal
Contact closure
Output to alarm system
by using photo-relay
4 systems, Output contents
are selected by menu.
2 ports
*The output sentence, mode and baud rate can be set at the TT Preset menu.
**Data cycle should be input with more than 40 Hz (HSC) or 20 Hz (normal speed).
5-1
5. INPUT/OUTPUT DATA
IEC 61162 input sentence and priority
Contents
Sentence and priority
Speed (STW)
VBW>VHW
Speed (SOG)
VBW
Speed (position)
VTG>RMC
Heading (True)
THS*>HDT*
Position
GNS>GGA>RMC>GLL
Datum
DTM
Waypoint
BWR, BWC, RMB
Route
WPL, RTE
Date, Time
ZDA
Depth
DPT >DBT>DBS>DBK
Temperature
MTW
Wind
MWV>VWT>VWR
Set and Drift
VDR
ALARM ACK
ACK
*: THS and HDT are IEC61162-2
Others: IEC61162-1 ed2.
IEC 61162 output sentence
Contents
Sentence
Target L/L
TLL *
Radar system data
RSD
Own ship data
OSD
TT target data
TTD, TLB, TTM
ALARM data
ALR
*non IMO-type only.
5-2
INSTALLATION MATERIALS
ACCESSORIES
UNIT
O U T L I N E
008-538-720
CP03-27201
008-538-730
FP03-10101
008-538-770 **
RSB-098-080-*
DESCRIPTION/CODE №
(略図の寸法は、参考値です。
03GO-X-9851
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
1.䍘-䍢䍼⇟ภᧃየ䈱[**]䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ/䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
INSTALLATION MATERIALS
工事材料
工事材料
ACCESSORIES
付属品
付属品
ANTENNA CHASSIS
空中線本体部
ユニット
N A M E
1/1
1
1
1
Q'TY
RSB-098-080/RSB-099-080/RSB-100-080/RSB-101-080/RSB-102-080
PACKING LIST
A-1
03GO-X-9851 -0
*':#)10*'#&5%4'9
౐ⷺ㩘㩨㩣㩎ో㩒㩆㩨
*':#)10#.076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁㩙㩣ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
%4+/210.7)
࿶⌕┵ሶ
%4+/210.7)
࿶⌕┵ሶ
%4+/210.7)
࿶⌕┵ሶ
6'4/+0#.12'0'4
ᠲ૞㩤㩔㩨㨺
#06+%14415+1047$$'4
㒐ⲁࠧࡓ
5'#.9#5*'4
㩆㨺㩣㩦㨹㩆㨶㨺
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
%1&'01
(8
.(
%1&'01
(8
%1&'01
(8
%1&'01
%1&'01
41*5
%1&'01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
)1: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-2a
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
%1..#4(14.+(6+0)
(+:674'
ขઃ↪㩀㩡㨺
.+(6+0)(+:674'
ษࠅ਄ߍ㊄ౕ
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
41*5
%1&'01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
⇟ภ
01
)1: ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
%1&'01 49
49
%1&'01
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
*':#)10#.*'#&$1.6
౐ⷺ㩘㩨㩣㩎
*':#)10#.076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
⇛‫ޓޓ‬࿑
176.+0'
6;2'
%1&'01
A-3
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
ฬ‫ޓޓ‬⒓
0#/'
#%%'5514+'5
⇟ภ
01
+056#..#6+10/#6'4+#.5
)1: ઃዻຠ⴫
%2
6;2'
A-2b
Ꮏ੐᧚ᢱ⴫
%1&'01
ANTENNA INSTALLATION MATERIALS
UNIT
O U T L I N E
008-254-590
SN5AF/7AF/30AF/36AF
008-505-950 **
SN30AF
(略図の寸法は、参考値です。
03FT-X-9851
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-4
03FT-X-9851 -0
DESCRIPTION/CODE №
1.䍘-䍢䍼⇟ภᧃየ䈱[**]䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ/䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
INSTALLATION MATERIALS
工事材料
アンテナ工材
ANTENNA
アンテナ組品
ユニット
N A M E
SN30AF/SN36AF
PACKING LIST
1
1
Q'TY
1/1
5+.+%1047$$'4
㩃㩚㩆㨺㩣
*':#)10#.*'#&$1.6
౐ⷺ㩘㩨㩣㩎
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
14+0)
1㩢㩧㩂㩨
)7+&'2+0
㩕㩩㩧
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%1&'01 59㨻㩣㩚㩋㨷㨺㩖㩨)
59㨻㩣㩚㩋㨷㨺㩖㩨)‫ޓ‬
%1&'01
/:575
%1&'01
/575‫ޓ‬
%1&'01
/575
%1&'01
,$#)
%1&'01
41*5
50#(#(#(/5##(#(
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
%3: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
%3:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
6;2'
%1&'01
A-5
INSTALLATION MATERIALS
UNIT
O U T L I N E
008-538-740
CP03-27301
000-081-241 **
PSU-007-70-23-S
(略図の寸法は、参考値です。
03GO-X-9853
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
1/1
1
1
Q'TY
A-6
03GO-X-9853 -0
DESCRIPTION/CODE №
1.䍘-䍢䍼⇟ภᧃየ䈱[**]䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ/䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
INSTALLATION MATERIALS
工事材料
工事材料
POWER CONTROL UNIT
電源制御部
ユニット
N A M E
PSU-007-*-*-*
PACKING LIST
%4+/210.7)
࿶⌕┵ሶ
%4+/210.7)
࿶⌕┵ሶ
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
(8㨻㨿
(8
%1&'
01
(8
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
)1: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-7
%14'%#$.'
㩃㨺㩖㩨㩣
%
%14'%#$.'
㩃㨺㩖㩨㩣
%
%14'%#$.'
㩃㨺㩖㩨㩣
%
%14'%#$.'
㩃㨺㩖㩨㩣
%
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%1&'01
49/
%1&'01
49/
%1&'01
49/
%1&'01
49/
(#4(%4
ᢙ㊂
36;
A-8
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
6;2'
%1&'01
+056#..#6+10/#6'4+#.5
#%%'5514+'5
52#4'2#465
52#4'2#465
70+6
176.+0'
&8+&&5.+0-/
(2
52
52
/7%45*-#6
&'5%4+26+10%1&'ͳ
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
#%↪
&%↪
36;
A-9
).: ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㪉㪅੍஻ຠ䈲䇮㪘㪚↪㪃㪛㪚↪䈪ㆬᛯ㗿䈇䉁䈜䇯
㪚㪟㪦㪦㪪㪜㩷㪪㪧㪘㪩㪜㩷㪧㪘㪩㪫㪪㩷㪛㪜㪧㪜㪥㪛㪠㪥㪞㩷㪦㪥㩷㪘㪚㩷㪦㪩㩷㪛㪚㩷㪧㪦㪮㪜㪩㪅
㪈㪅䍘䍎䍢䍼ᧃየ䈮㪲㪁㪁㪴䈱ઃ䈇䈢䍳䍤䍍䍢䈲ઍ⴫䈱ဳᑼ㪆䍘䍎䍢䍼䉕⴫␜䈚䈩䈇䉁䈜䇯
㪛㪦㪬㪙㪣㪜㩷㪘㪪㪫㪜㪩㪠㪪㪢㩷㪛㪜㪥㪦㪫㪜㪪㩷㪚㪦㪤㪤㪦㪥㪣㪰㩷㪬㪪㪜㪛㩷㪜㪨㪬㪠㪧㪤㪜㪥㪫㪅
%#$.'#55'/$.;
㩃㨺㩖㩨㩣⚵ຠ
Ꮏ੐᧚ᢱ
#%%'5514+'5
ઃዻຠ
ઃዻຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
&+52.#;70+6
⴫␜ㇱ
࡙࠾࠶࠻
0#/'
/7%4
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
5'.(6#22+0)5%4'9
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷
2#0'.*11-
㩔㩩㩒㩣㩖㨹㩂
2#0'.%18'4
㩔㩩㩒㩣㩀㩔㩨㨺
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
:575
%1&'01 41*5
%1&'01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
6;2'
ᢙ㊂
36;
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
#%%'5514+'5
ઃዻຠ⴫
%1&'01
A-10
+056#..#6+10/#6'4+#.5
#%%'5514+'5
52#4'2#465
52#4'2#465
70+6
176.+0'
&8+&&5.+0-/
(2
52
52
/7%45*-#4
&'5%4+26+10%1&'ͳ
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
)/:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
&%↪
#%↪
36;
A-11
)/: ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㪉㪅੍஻ຠ䈲䍂㪘㪚㪃㪛㪚䈪ㆬᛯ㗿䈇䉁䈜䇯
㪚㪟㪦㪦㪪㪜㩷㪪㪧㪘㪩㪜㩷㪧㪘㪩㪫㪪㩷㪛㪜㪧㪜㪥㪛㪠㪥㪞㩷㪦㪥㩷㪘㪚㩷㪦㪩㩷㪛㪚㩷㪧㪦㪮㪜㪩㪅
㪈㪅䍘䍎䍢䍼ᧃየ䈮㪲㪁㪁㪴䈱ઃ䈇䈢䍳䍤䍍䍢䈲ઍ⴫䈱ဳᑼ㪆䍘䍎䍢䍼䉕⴫␜䈚䈩䈇䉁䈜䇯
㪛㪦㪬㪙㪣㪜㩷㪘㪪㪫㪜㪩㪠㪪㪢㩷㪛㪜㪥㪦㪫㪜㪪㩷㪚㪦㪤㪤㪦㪥㪣㪰㩷㪬㪪㪜㪛㩷㪜㪨㪬㪠㪧㪤㪜㪥㪫㪅
%#$.'#55'/$.;
㩃㨺㩖㩨㩣⚵ຠ
Ꮏ੐᧚ᢱ
#%%'5514+'5
ઃዻຠ
ઃዻຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
&+52.#;70+6
⴫␜ㇱ
࡙࠾࠶࠻
0#/'
/7%4
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
&1%7/'06
+056#..#6+10/#6'4+#.5
52#4'2#465
70+6
176.+0'
15
+/
1/
1/
%2
%2
52
52
52
427
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㪉㪅䋨㪁㪈䋩䋨㪁㪉䋩䈲䇮䈠䉏䈡䉏઀᭽ㆬᛯຠ䉕⴫䈚䉁䈜䇯
䋨㪁㪈䋩䋨㪁㪉䋩㪠㪥㪛㪠㪚㪘㪫㪜㩷㪪㪧㪜㪚㪠㪝㪠㪚㪘㪫㪠㪦㪥㩷㪪㪜㪣㪜㪚㪫㪠㪭㪜㩷㪠㪫㪜㪤㪅
㪊㪅㩿㪁㪊㪀㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪઀᭽䈱ᤨ䈱䉂ᷝઃ䈘䉏䉁䈜䇯
㪪㪬㪧㪧㪣㪰㪜㪛㩷㪮㪠㪫㪟㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪㩷㪦㪥㪣㪰㪅
A-12
).: &'5%4+26+10%1&'ͳ
㪈㪅䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
12'4#6145)7+&'
ᠲ૞ⷐ㗔ᦠ
+056#..#6+10/#07#.
ⵝ஻ⷐ㗔ᦠ
12'4#6145/#07#.
ขᛒ⺑᣿ᦠ
12'4#6145/#07#.
ขᛒ⺑᣿ᦠ
࿑ᦠ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
52#4'2#465
੍஻ຠ
52#4'2#465
੍஻ຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
241%'551470+6
೙ᓮㇱ
࡙࠾࠶࠻
0#/'
427
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
%4+/210.7)
࿶⌕┵ሶ
6'4/+0#.12'0'4
ᠲ૞㩤㩔㩨㨺
6'4/+0#.12'0'4
ᠲ૞㩤㩔㩨㨺
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
(8
%1&'
01
%1&'
01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
೙ᓮㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14241%'5514
70+6
೙ᓮㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14241%'5514
70+6
೙ᓮㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14241%'5514
70+6
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%2
6;2'
#%↪
%1&'01
A-13
%75*+10
㩂㩢㨻㩔㩨㩧㩘㩩㩧
9#5*'4*'#&5&4'9$
㩏㩗㩨㩈㩛㩇$
)41//'6
㩂㩨㩥㩜㨹㩎
-$(+:+0)/'6#.
-$⋥ઃ㊄ౕ
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
6/
%1&'
01
/:%9/$0+
%1&'
01
)
%1&'
01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
ฬ‫ޓޓ‬⒓
0#/'
47$$'4(116
㩂㩢㨻㩔㩨㩧㩘㩩㩧
9#5*'4*'#&5&4'9$
㩏㩗㩨㩈㩛㩇$
)41//'6
㩂㩨㩥㩜㨹㩎
$.+0&5'#.
㩖㩨㩡㨼㩧㩎㩨㩆㨺㩣
-';$1#4&(+:674'
-$⋥ઃ㊄ౕ
6
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
%1&'
01
6/
%1&'
01
/:%9/$0+
%1&'
01
)
%1&'
01
41*5
%1&'
01
41*5
6;2'
%1&'01
ᢙ㊂
36;
A-15
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓ‬
‫(ޓ‬14%10641.70+6
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
#%%'5514+'5
⇟ภ
01
#%%'5514+'5
ઃዻຠ⴫
(2
6;2'
).: ઃዻຠ⴫
%1&'01
A-14
9+0)5%4'9
Ⲕ㩘㩨㩣㩎
*':076
౐ⷺ㩏㨹㩎‫ޓ‬㧝⒳
9#5*'4*'#&5&4'9$
㩏㩗㩨㩈㩛㩇$
(.75*/1706+0)2.#6'
㩖㩡㨹㩆㨷㩙㨽㩧㩎㊄ౕ
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
/:575
%1&'
01
/575
%1&'
01
/:%9/$0+
%1&'
01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
ฬ‫ޓޓ‬⒓
0#/'
*':$1.6
5.166'&9#5*'4*'#&
౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
*':$1.6
౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
50#2$76610
㩇㩏㨹㩖㩩㩘㩨㩊㩧
*1.'2.7)
㩘㨺㩣㩖㩩㩡㩂㩨
*#0)'456#;
㩔㩧㩀㩨㨺㩅㩅㨾
*#0)'44
㩔㩧㩀㩨㨺4
*#0)'4.
㩔㩧㩀㩨㨺.
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
%1&'01
/:575
%1&'01
/:575
%1&'01
/575‫ޓ‬
%1&'01
/575
%1&'01
-$㩠㨽‫ޓ‬㩘㩨㩊㩧㩂㩥
%1&'01
%2*2
%1&'01
41*5
%1&'01 %1&'01 41*5
41*5
6;2'
%1&'01
ᢙ㊂
36;
A-17
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
#%%'5514+'5
⇟ภ
01
#%%'5514+'5
ઃዻຠ⴫
(2
6;2'
A-16
).: ઃዻຠ⴫
%1&'01
*':$1.6
5.166'&9#5*'4*'#&
౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
*':$1.6
౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
50#2$76610
㩇㩏㨹㩖㩩㩘㩨㩊㩧
*1.'2.7)
㩘㨺㩣㩖㩩㩡㩂㩨
*#0)'456#;
㩔㩧㩀㩨㨺㩅㩅㨾
*#0)'44
㩔㩧㩀㩨㨺4
*#0)'4.
㩔㩧㩀㩨㨺.
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
/:575
%1&'01
/:575
%1&'01
/575‫ޓ‬
%1&'01
/575
%1&'01
-$㩠㨽‫ޓ‬㩘㩨㩊㩧㩂㩥
%1&'01
%2*2
%1&'01
41*5
%1&'01 %1&'01 41*5
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)/:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
ฬ‫ޓޓ‬⒓
0#/'
9#8'9#5*'4
ᵄᐳ㊄
18#.*'#&5%4'9
ਣ⋁ዊ㩒㩆㩨
415'66'9#5*'4
㩥㨺㩈㩨㨹㩎ᐳ㊄
*#0&.'
ขᚻ
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
%1&'
01
99575
%1&'
01
/:%9㩘㩩㩢㩆㨺㩣
%1&'
01
/%9㩘㩩㩢㩆㨺㩣
/%9㩘㩩㩢㩆㨺㩣
%1&'
01
41*5
6;2'
%1&'01
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
).: A-19
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
#%%'5514+'5
⇟ภ
01
#%%'5514+'5
)/: ઃዻຠ⴫
(2
6;2'
ઃዻຠ⴫
%1&'01
A-18
16*'4+056#..#6+10/#6'4+#.5
+056#..#6+10/#6'4+#.5
70+6
176.+0'
/,#52(%
2'26:$.
2'26:$.
%2
%7
&'5%4+26+10%1&'ͳ
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
)1:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
36;
A-20
)1: ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
ߘߩઁᎿ᧚
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
/'/14;%#4&+06'4(#%'
㩜㩝㩢㨺㩀㨺㩎㩨㨼㩧㩊㨺㩖㨴㨼㩇
࡙࠾࠶࠻
0#/'
%7(#4
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
.#$'.#66#%*+0)
241%'&74'
⥽ベ㩙㨺㩂⾍ઃⷐ㗔
6*4'#&'&41&
ኸಾ㩘㩨㩣㩎
*':076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
56''4+0)9*''..#$'.
⥽ベ⾍ࠅ㩙㨺㩂
$5*
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
%㩦㨾㨼
%1&'
01
/:575
%1&'
01
/575
%1&'
01
/575
%1&'
01
/575
%1&'
01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
)1: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-21
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇#
5'.(6#22+0)5%4'9
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷
/1706+0)$4#%-'6
㩔㩧㩀㩨㨺
ฬ‫ޓޓ‬⒓
0#/'
%1&'
01
/:%9/$0+
%1&'
01
:575
%1&'
01
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇#
*':076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
)41//'6
㩂㩨㩥㩜㨹㩎
/1706+0)$4#%-'6
㩄㩧㩉㨺㩣㩠㨽ขઃ᧚
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
%1&'01
/:%9/$0+
%1&'01
/575
%1&'01
/575
%1&'01
/575
%1&'01
%0)3'27.
%1&'01
41*5
6;2'
%1&'01
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
)1: A-23
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
#%%'5514+'5
↪ㅜ㧛஻⠨
4'/#4-5
#%%'5514+'5
ᢙ㊂
36;
)1: ઃዻຠ⴫
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
6;2'
ઃዻຠ⴫
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
A-22
%172.+0)2.#6'#55;
ㅪ⚿บ
⚵ຠ
㩏㩗㩨㩈㩛㩇$
9#5*'4*'#&5&4'9$
176.+0'
&'5%4+26+10%1&'ͳ
36;
52#4'2#465
੍஻ຠ
52
52#4'2#465
16*'42#465
)%㩀㩔㩨㨺⚵ຠ
/:%9/$0+
).:
36;
/:%9/$0+
9#5*'4*'#&5%4'9
㩄㩒㩂㩊
2
2
(74
%100'%614
㩄㩒㩂㩊
0*%100'%614#55;
8*㩄㩒㩂㩊
&'5%4+26+10%1&'ͳ
)%%18'4#55;
0*㩄㩒㩂㩊
176.+0'
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇#
ߘߩઁㇱຠ
0#/'
㩏㩗㩨㩈㩛㩇$
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
%1&'
01
12
%1&'
01
/:%9/$0+
↪ㅜ㧛஻⠨
4'/#4-5
ᢙ㊂
36;
ဳฬ㧛ⷙᩰ
&'5%4+26+105
⇛‫ޓޓ‬࿑
176.+0'
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
⇟ภ
01
Ꮏ੐᧚ᢱ⴫
A-24
0#/'
੍஻ຠ
).: )%
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
12
6;2'
A-25
).: %1&'01
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
(74
%100'%614
8*%100'%614#55;
8*㩄㩒㩂㩊
2
8*%100'%614#55;
:*2*㩄㩒㩂㩊
2
:*2*%100'%614#55;
Ṷ▚㩖㩩㩢㩧㩎
2#
.(
241%'5514$1#4&
㩏㩗㩨㩈㩛㩇$
/:%9/$0+
9#5*'4*'#&5%4'9
$
ဳᑼ䎒䱤䱚䱮䲈⇟ภ䬛䯾Ბ䬽႐ว䫺ਅᲑ䭗䭙਄Ბ䬺ઍ䭞䭚ㆊᷰᦼຠ䬶䬑䭙䫺䬸䬰䭘䬚䬛౉䬲䬵䬓䭍䬨䫻䫹䬹䬙䫺ຠ⾰䬾ᄌ䭞䭙䭍䬪䭢䫻
䯴⇛࿑䬽ኸᴺ䬾䫺ෳ⠨୯䬶䬨䫻䎃䎧䎬䎰䎨䎱䎶䎬䎲䎱䎶䎃䎬䎱䎃䎧䎵䎤䎺䎬䎱䎪䎃䎩䎲䎵䎃䎵䎨䎩䎨䎵䎨䎱䎦䎨䎃䎲䎱䎯䎼䎑䯵
䎷䎺䎲䎃䎷䎼䎳䎨䎶䎃䎤䎱䎧䎃䎦䎲䎧䎨䎶䎃䎰䎤䎼䎃䎥䎨䎃䎯䎬䎶䎷䎨䎧䎃䎩䎲䎵䎃䎤䎱䎃䎬䎷䎨䎰䎑䎃䎃䎷䎫䎨䎃䎯䎲䎺䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎃䎰䎤䎼䎃䎥䎨䎃䎶䎫䎬䎳䎳䎨䎧䎃䎬䎱䎃䎳䎯䎤䎦䎨䎃䎲䎩䎃䎷䎫䎨䎃
䎸䎳䎳䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎑䎃䎴䎸䎤䎯䎬䎷䎼䎃䎬䎶䎃䎷䎫䎨䎃䎶䎤䎰䎨䎑
).:
%172.+0)2.#6'#55;
ㅪ⚿บ
⚵ຠ
9#5*'4*'#&5&4'9$
㩏㩗㩨㩈㩛㩇$
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
12
%1&'
01
/:%9/$0+
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
12
6;2'
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-26
16*'42#465
176.+0'
/%9
53
&8+&&5.+0-/
&8+&&5.+0-/
2
2
2
2$
.(
5.$(40#
/:%9/$0+
&'5%4+26+10%1&'ͳ
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
36;
A-27
).: ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
524+0)9#5*'4
㩔㩨㩒㩅㩨㩀㩨㩒
52#%'4
㩇㩗㩩㨺㩅㨺
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
:*%100'%614
:*㩄㩒㩂㩊
:*%100'%614
:*㩄㩒㩂㩊
8*%100'%614
8*㩄㩒㩂㩊
4)$$7(($1#4&
4)$$7((㩖㩩㩢㩧㩎
&8+4)$#55;
&8+4)$⚵ຠ
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇$
0#/'
ߘߩઁㇱຠ
12
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
/1&7.#4%100%614
㩄㩒㩂㩊
㩝㩆㩨㨷㩡㨺
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
/25%
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
%2
6;2'
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-28
For processor unit (220 VAC set)
For processor unit (100 VAC set)
For display unit (MU-201CR/231CR, AC set)
A-29
For GC-10
A-30
14/Feb/2011
Y.NISHIYAMA
D-1
Y. Hatai
D-2
D-3
May 17'07 R.Esumi
1/Sep/2010
Y.NISHIYAMA
D-4
Y. Hatai
Takahashi T.
D-5
Y. Hatai
Takahashi T.
D-6
1/Sep/2010
Y.NISHIYAMA
D-7
Jan.18'08 R.Esumi
D-8
Apr.23'07 R.Esumi
D-9
Apr.23'07 R.Esumi
D-10
Apr.23'07 R.Esumi
D-11
Apr.23'07 R.Esumi
D-12
Apr.23'07 R.Esumi
D-13
D-14
D-15
D-16
Y. Hatai
D-17
Y. Hatai
D-18
Y. Hatai
D-19
Y. Hatai
D-20
Y. Hatai
D-21
Apr.05'04
D-22
注記
*1 :
*2 :
*3 :
*4 :
*5 :
*6 :
D
造船所手配。
オプション。
最長 100m (延長するときは接続箱RJB-001が必要 )。
船内配電盤では3Aのブレーカを使用。
保護アース用ケーブルは緑/黄の絶縁線を使用のこと。
交流は両極切りブレーカ(造船所手配)を経由すること。
BNCコネクタコンバータ
BNC CONNECTOR
CONVERTER *2
DSUB-BNC-1
保護アース
PE *1 *5
IV-8sq.
トランス
TRANSFORMER
RU-1803 *2
表示部 MONITOR UNIT
MU-190/201CR (FAR-2137S)
MU-231/231CR (FAR-2837S)
NOTES
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: MAX. 100m. (JUNCTION BOX RJB-001 IS REQUIRED FOR EXTENSION)
*4: USE 3A BREAKER IN SHIP'S MAINS SWITCH BOX.
*5: USE GRN/YEL WIRE FOR PROTECTIVE EARTH.
*6: PASS THE AC LINE THROUGH A DOUBLE-CONTACT BREAKER (SHIPYARD SUPPLY).
保護アース
PE *1 *5
IV-8sq.
DRAWN
9/Aug/2010
CHECKED
9/Aug/2010
APPROVED
10/Aug/2010
SCALE
DWG.No.
1
2
3
4
5
6
7
8
防水型カードインターフェイス
MEMORY CARD I/F UNIT
CU-200
C3521-C01- P
1
2
3
4
5
6
7
8
1
2
3
TXP
TXN
RXP
NC
NC
RXN
NC
NC
*2
REF.No.
AC
AC
GND
P
P
T.YAMASAKI
T.TAKAHASHI
MASS
kg
03-163-6002-3
シロ/ミドリ
ミドリ
シロ/ダイ
アオ
シロ/アオ
ダイ
シロ/チャ
チャ
WHT/GRN
GRN
WHT/ORG
BLU
WHT/BLU
ORG
WHT/BRN
BRN
NR203PF-VVS1.25
3.5m, φ8.6
MPS588-C
100-230VAC
1φ,50/60Hz
*1
LAN CABLE(CAT5) OR
FR-FTPC-CY,10/20/30m,φ13
P5E-4PTX-BL,10m,φ6.3
1
2
3
4
5
6
7
8
24
1
2
BRN
RED
ORG
YEL
GRN
NETWORK
SAME AS AVOBE
DVI-D MONITOR
J205
TXP
TXN
RXP
NC
NC
RXN
NC
NC
1
2
3
4
5
1
2
1
2
3
4
5
6
7
8
9
J622
SYS_ACK-H
SYS_ACK-C
J601
NC
RXD
TXD
NC
GND
NC
NC
NC
NC
P
P
J607
LOG-A 1
LOG-B 2
NC 3
J619
ARPA-A 1
ARPA-B 2
NC 3
J611
AIS_TD-A 1
AIS_TD-B 2
AIS_RD-A 3
AIS_RD-B 4
AIS_GND 5
J502/J522
KEY_TXD-B
KEY_TXD-A
KEY_RXD-B
KEY_RXD-A
PWR_SW
GND
+12V
GND
NC
NC
PC
*1
IV-1.25sq.
TYPE
名 称
Y.NISHIYAMA
NAME
RW-4864,φ9.5
RW-4864,φ9.5
1
2
3
4
5
6
7
8
9
10
SUB DISPLAY2
(SEMI-LOG)
SUB DISPLAY1
(FULL-LOG)
MASTER RADAR
ALARM SYSTEM
(IEC-61162-2)
AIS
(IEC-61162-1)
TRACK_CONTROL
(IEC-61162-1)
ECDIS
(IEC-61162-1)
SPEED LOG
(IEC-61162-1)
NAVIGATOR
(IEC-61162-2)
HDG SENSOR
RW-4864,φ9.5
*1
TTYCS-7
*1
TTYCS-4
*1
TTYCS-4
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1Q
RS-232C CABLE *1
J501/J521
1 KEY_TXD-B
2 KEY_TXD-A
3 KEY_RXD-B
4 KEY_RXD-A
5 PWR_SW
6 GND
7 +12V
8 GND
9 SYS_FAIL-H
10 SYS_FAIL-C
J507/J527
1 SYS_FAIL-H
2 SYS_FAIL-C
3 SYS_ACK-H
4 SYS_ACK-C
1
2
3
4
5
6
7
8
9
10
J501
KEY_TXD-B
KEY_TXD-A
KEY_RXD-B
KEY_RXD-A
PWR_SW
GND
+12V
GND
NC
NC
XH10P-W-5P-A
1.5/10/20/30m,φ9
5
J618(NH)
GND 1
OP_HD_2 2
GND 3
OP_BP_2 4
GND 5
OP_TRIG_2 6
GND 7
OP_VIDEO_2 8
J617(NH)
GND 1
OP_HD_1 2
GND 3
OP_BP_1 4
GND 5
OP_TRIG_1 6
GND 7
OP_VIDEO_1 8
J616(NH)
GND 1
OP_HD_IN 2
GND 3
OP_BP_IN 4
GND 5
OP_TRIG_IN 6
GND 7
OP_VIDEO_IN 8
P
P
P
P
P
P
P
P
P
P
P
J606
NAV-A 1
NAV-B 2
NC 3
J620
TRK_TD-A 1
TRK_TD-B 2
TRK_RD-A 3
TRK_RD-B 4
GND 5
P
J605
HDG-A 1
HDG-B 2
HDG_GND 3
J612
ALARM1_0 1
ALARM1_1 2
ALARM2_0 3
ALARM2_1 4
ALARM3_0 5
ALARM3_1 6
OPERATOR_FITNESS_0 7
OPERATOR_FITNESS_1 8
EXT_ALM_ACK_N 9
GND 10
SYS_FAIL-H 11
SYS_FAIL-C 12
J614
1 +12V
2 GND
J615
+12V
GND
+5V
GND
-12V
J602
KEY_TXD-B 1
KEY_TXD-A 2
KEY_RXD-B 3
KEY_RXD-A 4
PWR_SW 5
GND 6
+12V 7
GND 8
SYS_FAIL-H 9
SYS_FAIL-C 10
XH10P-W-6P
2.3/10/20/30m,φ9
合計:33m以下 TOTAL: UP TO 33m
4
P
P
MPS588-C
MJ-A3SPF0015,10m,φ6
DVI-D/DSINGLELINK5M/10M
5/10m,φ7
シロ WHT
クロ BLK
MJ-A3SPF
RGBビデオコンバータ
RGB VIDEO CONVERTOR
DVI-RGB-1 *2
*2
DVI CABLE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
チャ
アカ
ダイ
キ
ミドリ
23
24
1
2
制御部
PROCESSOR UNIT
RPU-013
J302
TXP
TXN
RXP
NC
NC
RXN
NC
NC
1
2
3
DVI-D MONITOR
J204
DVI0TX2_N
DVI0TX2_P
A_GND
NC
NC
NC
NC
NC
DVI0TX1_N
DVI0TX1_P
A_GND
NC
NC
VCC
GND
NC
DVI0TXD_N
DVI0TXD_P
A_GND
NC
NC
A_GND
DVI0TXC_P
DVI0TXC_N
1
2
3
4
5
6
RS-232C
外部モニター
EXT. MONITOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
J3
3
J1
+12V 1
GND 2
FG 3
J3
VCC
GND
-5/-12V
操作部
CONTROL UNIT
RCU-014/015
TMDS_DATA2(-)
TMDS_DATA2(+)
TMDS_DATA2/4_SHIELD
NC
NC
DDC_CLOCK
DDC_DATA
NC
TMDS_DATA(-)
TMDS_DATA(+)
TMDS_DATA1/3_SHIELD
NC
NC
+5V_POWER
GND
HOT_PLUG_DETECT
TMDS_DATAB(-)
TMDS_DATAB(+)
TMDS_DATA0/5_SHIELD
NC
NC
TMDS_CLOCK_SHIELD
TMDS_CLOCK(+)
TMDS_CLOCK(-)
J3
J9
R
GND
G
GND
B
GND
HS
GND
VS
GND
J4
+12V
+12V
GND
GND
NC
NC
*2
TB1
1 H
2 C
5
6
7
8
9
10
3
4
1
2
TB801
TX_HV
NC
24V_PLUS
24V_MINUS
NC
NC
NC
NC
SPU_RF_D-A
SPU_RF_D-B
RF_SPU_D-A
RF_SPU_D-B
SG
GND
TB802
IF_VIDEO
GND
操作部
CONTROL UNIT
RCU-016
*1
DPYC-2.5
1
2
3
4
5
6
7
8
9
10
11
12
13
1
2
3
P
4
P
ORG[B]
YEL[B]
BLU[B]
GRY[B]
PPL[B]
WHT[B]
RED
GRN
BLK
WHT
GRN[B]
RED[B]
ダイ(太)
キ(太)
アオ(太)
ハイ(太)
ムラサキ(太)
シロ(太)
アカ
ミドリ
クロ
シロ
ミドリ(太)
アカ(太)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
*6
100-230VAC
1φ,50-60Hz
TB1
1 H
2 C
J1
03-2091(5P)
チャ BRN
アカ RED
ダイ ORG
キ
YEL
TB BOARD
03P9342
*1
100-120/ *6 DPYC-2.5
200-230VAC
1φ,50-60Hz
R_VIDEO
GND
G_VIDEO
GND
B_VIDEO
GND
H_SYNC
GND
V_SYNC
GND
VCC
GND
-5/-12V
RGB バッファ 基板
RGB BUFFER PCB
03P9229A
*1
DPYC-1.5
J2
R_VIDEO
G_VIDEO
B_VIDEO
NC
NC
GND
GND
GND
NC
GND
GND
NC
H_SYNC
Y_SYNC
NC
1
2
3
4
5
DVI-RGB変換基板
DVI-RGB CONVERSION BOARD
SLB-FRN4-A
440VAC *6
1φ,50-60Hz
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GYRO CONVERTER
BOARD
64P1106A *2
J7(NH)
DATA1-H
DATA1-C
SHIFT1-H
SHIFT1-C
FG
BRN
チャ
*3
RW-9600,15/30/40/50m,φ22
RW-4747
VDR
*1
VGA CABLE
1
2
3
BRN
RED
1
ORG
2
YEL
3
GRN
4
BLU
5
PPL
03-2089(5P)
J604
1 +12V
2 GND
J603(XH)
J613
GC_LED
TX_HV 1
GC_HOLD
NC 2
GC_UP
J610
24V_PLUS 1
GC_DOWN
GC_0V
24V_MINUS 2
MOTOR(+) 3
GC_5V
MOTOR(+) 4
J608
AD_DATA-H MOTOR(-) 5
AD_DATA-C MOTOR(-) 6
AD_CLK-H SPU_RF_D-A 7
AD_CLK-C SPU_RF_D-B 8
RF_SPU_D-A 9
RF_SPU_D-B 10
SG 11
GND 12
J609
IF_VIDEO
GND
1 100VAC-H
2 100VAC-C
3 NC
TB901
空中線部
パフォーマンスモニター
ANTENNA UNIT
PERFORMANCE MONITOR
PM-51
RSB-098/099
RSB-100/101/102
*1
COAX.(75Ω)x5
RGB EXT. MONITOR
保護アース
PE
*1 *5
IV-8sq.
*1
TTYCS-4
J602
チャ
アカ
ダイ
キ
ミドリ
アオ
ムラサキ
保護アース
PE
*1 *5
IV-8sq.
1
2
3
4
5
6
7
電源制御部
POWER SUPPLY UNIT
PSU-007
03-2088(6-14P) 1
2
3
4
5
6
*1
110/115/
*2
220/230VAC, DPYC-1.5 RU-3305
1φ,50-60Hz
DPYCY-1.5 *1
100VAC,1φ,
50-60Hz
氷結防止用
FOR DE-ICER *4
TPYCY-2.5 *1
IV-3.5sq.
保護アース
PE *1 *5
*1
MPYC-7
9
10
11
12
13
14
TB1
+12V 1
ANT_0V-N 2
J5(VH)
GYRO_R2
GYRO_R1
NC
J4(VH)
GYRO_S1
GYRO_S2
GYRO_S3
GYRO_T
GYRO_FG
J1
*1
DPYC-1.5
B
RU-5466-1 *2
RU-6522 *2
XK1
U 4
V 6
W 9
A
A-D CONVERTER
GYROCOMPASS
C
RU-5693 *2
K2
1 U
3 V
5 W
TB902
1 U
2 V
3 W
03-2090(3P)
*1
200/380VAC,3φ,50Hz TPYC-2.5
220/440VAC,3φ,60Hz
*1
TPYC-2.5
110VAC,3φ,60Hz
*1
TPYC-2.5
220VAC,3φ,50Hz
*1
TPYC-2.5
440VAC,3φ,50Hz
1
6
S-1
空中線型式 回転数 電源
ANT. TYPE
RPM
POWER SUPPLY
RSB-098
21/26 200/220VAC
RSB-099
380/440VAC
220VAC,50Hz
RSB-100
220VAC,60Hz
RSB-101
45
440VAC,60Hz
RSB-102
LAN
スイッチング ハブ
*2
SWITCHING HUB
HUB-100 (8 PORTS)
保護アース PE
IV-1.25sq. *1 *5
FAR-2137S/2837S
船舶用レーダー/ARPA
相互結線図
MARINE RADAR/ARPA
INTERCONNECTION DIAGRAM
Download PDF

advertising