Service manual | Furuno FA-100 Marine RADAR User Manual

Back
UAIS TRANSPONDER
FA-100
PRINTED IN JAPAN
The paper used in this manual
is elemental chlorine free.
FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone :
0798-65-2111
Fax
0798-65-4200
:
All rights reserved.
Printed in Japan
FIRST EDITION : SEP. 2002
H5
: OCT. 17, 2005
Pub. No. IME-44170-H5
( AKMU ) FA-100
*00080932513*
*00080932513*
*00080932513*
SAFETY INSTRUCTIONS
CAUTION
WARNING
ELECTRICAL SHOCK HAZARD
Do not open the equipment
unless totally familiar with
electrical circuits and
service manual.
Only qualified personnel
should work inside the
equipment.
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage the equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Standard
compass
Steering
compass
FA-100
1.0 m
0.6 m
CB-100
0.6 m
0.4 m
GVA-100
0.3 m
0.3 m
DB-1
0.3 m
0.3 m
PR-240-CE
0.9m
0.6 m
Attach securely protection
earth to the ship's body.
Be sure that the power supply is
compatible with the voltage rating of
the equipment.
The protection earth is required
to the power supply to prevent
electrical shock
Connection of an incorrect power supply
can cause fire or damage the equipment.
The voltage rating of the equipment appears
on the label above the power connector.
i
TABLE OF CONTENTS
SYSTEM CONFIGURATION................................................................................ iii
EQUIPMENT LISTS ............................................................................................. iv
1. MOUNTING ....................................................................................................... 1
1.1 Antenna Unit....................................................................................................................1
1.1.1 GPS antenna unit ...............................................................................................1
1.1.2 VHF antenna ......................................................................................................3
1.1.3 GPS/VHF combined antenna ..............................................................................5
1.2 Transponder Unit .............................................................................................................8
1.3 Junction Box..................................................................................................................10
1.4 Power Supply (option) ...................................................................................................11
1.5 Pilot Plug (option) ..........................................................................................................11
2. WIRING ........................................................................................................... 12
3. INPUT/OUTPUT SIGNAL ............................................................................... 15
3.1 Inputs from Sensors.......................................................................................................15
3.2 Input/Output of AIS Signal .............................................................................................16
3.3 Input of Gyrocompass Signal.........................................................................................17
3.4 Alarm Signal Output.......................................................................................................17
3.5 LAN Input/Output...........................................................................................................18
3.6 Pilot Plug .......................................................................................................................18
3.7 Jumper Setting in the Junction Box................................................................................19
3.8 Input/Output Sentences .................................................................................................20
3.9 Changing Ship’s Mains Specifications............................................................................21
4. SETTING AND ADJUSTMENT ....................................................................... 22
4.1 Setting MMSI, IMO No., Name and Call Sign ................................................................22
4.2 Setting GPS Antenna Position and Ship’s Type .............................................................24
4.3 System Settings.............................................................................................................26
PACKING LIST
OUTLINE DRAWINGS
INTERCONNECTION DIAGRAM
ii
SYSTEM CONFIGURATION
Either
GPS antenna
GPA-017S
GSC-001
VHF whip antenna
GPS/VHF
combined antenna
GVA-100
Distributor unit
DB-1
Transponder unit
FA-100
Junction box CB-100
Power supply
PR-240-CE
AD-100
GPS Navigator *
Other external equipments
Gyrocompass
: Standard
Ship’s mains
100-115/200-230 VAC
1f, 50/60Hz
: Option
: Local supply
24 VDC
12-24 VDC
*: External GPS Navigation is required.
Category of the units
GPA-017S
GSC-001
GVA-100
FA-100
CB-100
DB-1
PR-240-CE
Exposed to the weather
Exposed to the weather
Exposed to the weather
Protected from the weather
Protected from the weather
Protected from the weather
Protected from the weather
iii
EQUIPMENT LISTS
Standard supply
No.
Name
Type
Code no.
Qty
Remarks
1
Transponder Unit
FA-100
-
1
2
Junction Box
CB-100
-
1
3
GPS Antenna
GPA-017S
-
GPS Antenna
GSC-001
-
GPS/VHF Combined
Antenna
Installation Materials
GVA-100*
-
1
Select one.
CP24-00101*
005-950-730
1
For DB-1
CP24-00102*
005-950-700
1
For FA-100
CP05-08701*
005-949-280
1
For CB-100
CP24-00121**
005-952-350
1
For GPA-017S
CP24-00141*
005-952-330
1
For GVA-100
4
**: for Japan only
Optional supply
No.
Name
1 Antenna cable set
Type
CP20-01700(30m)
Code no.
Remarks
004-372-110 For GPS or Combined antenna
8D-FB-CV *30M*, CP20-01701
2
Antenna cable set
CP20-01710(50m)
004-372-120
For GPS or Combined antenna
8D-FB-CV *50M*, CP20-01701
3
Flush mount kit A
OP24-1
005-950-740
4
5
Flush mount kit B
Mast mount fixture
OP24-2
CP20-01111
005-950-750
004-365-780 For GPA-017S
6
Right-angle
antenna base
L-angle antenna
base
No.13-QA330
000-803-239 For GPA-017S
No.13-QA310
000-803-240 For GPA-017S
Antenna base for
rail mount
VHF whip antenna
No.13-RC5160
000-806-114 For GPA-017S
FAB-151D
000-572-029 For Japan only
10
Antenna fixing
bracket
4-310071
000-572-184 For FAB-151D
11
VHF whip antenna
150M-W2VN
000-113-498 For outside Japan
12
Power supply
PR-240-CE
13
Pilot plug
OP24-3
000-053-911
14
15
AD-100
AD-100
OP24-24-1
For gyrocompass
005-954-420 CD-ROM, USB protect key
7
8
9
16
PC AIS
software kit
φ80 Mast mount kit OP24-5
-
005-954-510 For Combined antenna
*: Refer to packing list at the back of this manual.
iv
Include installation materials
CP24-00151*
1. MOUNTING
1.1 Antenna Unit
1.1.1 GPS antenna unit
Install the GPS antenna unit referring to the drawing at the back of this manual D-1.
When selecting a mounting location for the antenna, keep in mind the following
points.
• Select a location out of the radar beam. The radar beam will obstruct or prevent
reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible to keep it free of interfering objects and
water spray, which can interrupt reception of GPS satellite signal if the water freezes.
Extending antenna cable
Three types of antenna cable extensions are optionally available.
a) Antenna cable set CP20-01700
Antenna Unit
0.6 m
1m
: Connector
Conversion
Cable Assy.
NJ-TP-3DXV-1
Antenna Cable
30 m
1m
FA-100
Fabricate locally. (See next page.)
◆ Waterproofing connector
Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with
a cable-tie.
Waterproofing connector
b) Antenna cable set CP20-01710 (8D-FB-CV, 50m)
Connect the cable the same as a) above.
c) Cable type RG-10U/Y (shipyard supply)
Note: The length of this cable should be less than 20 m to prevent signal loss.
The coax. coupling cable assy.(type: NJ-TP+3DXV-1, code no.
000-123-809), coaxial connector(N-P-8DFB; supplied), vulcanizing tape
and vinyl tape are required. Fabricate both ends of the cable as shown in
the figure on the next page.
1
How to attach the connector N-P-8DFB for cable 8D-FB-CV
Outer Sheath
Armor
Dimensions in millimeters.
Inner Sheath Shield
50
Remove outer sheath and armor by the dimensions
shown left.
Expose inner sheath and shield by the dimensions
shown left.
30
Cover with heat-shrink tubing and heat.
Cut off insulator and core by 10mm.
10
30
Twist shield end.
Ship on clamp nut, gasket and clamp as shown left.
Clamp
Nut
Gasket Clamp
(reddish
brown)
Aluminum Foil
Fold back shield over clamp and trim.
Trim shield here.
Insulator
Cut aluminum foil at four places, 90° from one
another.
Fold back aluminum foil onto shield and trim.
Trim aluminum
tape foil here.
1
Expose the insulator by 1mm.
5
Expose the core by 5mm.
Pin
Clamp Nut
Shell
Solder through
the hole.
Slip the pin onto the conductor. Solder them together
through the hole on the pin.
Insert the pin into the shell. Screw the clamp nut into
the shell.
(Tighten by turning the clamp nut. Do not tighten by
turning the shell.)
How to attach connector N-P-8DFB
2
1.1.2 VHF antenna
Location
Location of the mandatory AIS VHF-antenna should be carefully considered. Digital
communication is more sensitive than analog/voice communication to interference
created by reflections in obstructions like masts and booms. It may be necessary to
relocate the VHF radiotelephone antenna to minimize interference effects.
To minimise interference effects, the following guidelines apply:
• The AIS VHF antenna should be placed in an elevated position that is as free as
possible with a minimum of 0.5 meters in the horizontal direction from constructions
made of conductive materials. The antenna should not be installed close to any large
vertical obstruction. The objective for the AIS VHF antenna is to see the horizon
freely through 360 degrees.
• The AIS VHF antenna should be installed safely away from interfering high-power
energy sources like radar and other transmitting radio antennas, preferably at least 3
meters away from and out of the transmitting beam.
• There should not be more than one antenna on the same plane. The AIS VHF
antenna should be mounted directly above or below the ship’s primary VHF
radiotelephone antenna, with no horizontal separation and with a minimum of 2.8
meters vertical separation. If it is located on the same plane as other antennas, the
distance apart should be at least 10 meters.
Cabling
• The cable should be kept as short as possible to minimize signal attenuation.
Coaxial cables equal to or better than RG10U/Y are recommended.
• All outdoor installed connectors on coaxial cables should be fitted with preventive
isolation such as vulcanizing tape to protect against water penetration into the
antenna cable.
• Coaxial cables should be installed in separate signal cable channels/tubes and at
least 10 cm away from power supply cables. Crossing of cables should be done at
right angles (90°). The minimum bend radius of the coaxial cable should be 5 times
the cable's outer diameter.
• Install the VHF whip antenna referring to the outline drawing at the back of this
manual. Separate this antenna from other VHF radiotelephone antennas as shown
on the next page to prevent interference to the FA-100.
3
Horizontal separation distance
Other VHF whip antenna
Whip antenna for AIS
(GPS/VHF combined
antenna)
More than 10 m
Vertical separation distance
More than
2.8 m
More than 0.5 m
• When coaxial cable RG-10U/Y (shipyard supply) is used, attach the coaxial plug
M-P-7 (dockyard supply) as shown on the next page.
4
How to attach the plug M-P-7
Lay the coaxial cable and attach an M-type plug (if necessary) to the cable as
follows.
30 mm
Sheath
1. Remove the sheath by 30 mm.
2. Bare 23 mm of the center conductor. Trim
braided shield by 5 mm and tin.
3. Slide coupling ring onto cable.
4. Screw the plug assembly on the cable.
5. Solder plug assembly to braided shield
through solder holes. Solder contact sleeve
to conductor.
6. Screw coupling ring into plug assembly.
5 mm
2 mm
Conductor
Braided shield
Insulator
Plug assembly
Coupling ring
Contact sleeve
Solder both
sides of hole.
Cut conductor here.
1.1.3 GPS/VHF combined antenna
Install the combined antenna unit referring to the outline drawing. When selecting a
mounting location for the antenna, keep in mind the following points.
• Select a location out of the radar beam. The radar beam will obstruct or prevent
reception of the GPS satellite signal.
• There should be no interfering object within the line-of-sight to the satellites. Objects
within line-of-sight to a satellite, for example, a mast, may block reception or prolong
acquisition time.
• Mount the antenna unit as high as possible. Mounting it this way keeps it free of
interfering objects and water spray, which can interrupt reception of GPS satellite
signal if the water freezes.
• Also, refer to the antenna installation guidelines page 3.
Outdoor
Indoor
Distributor DB-1
GPS
VHF
N-P-8DFB
RG-10U/Y
Transponder unit
N-P-8DFB
Installation overview of GPS/VHF combined antenna
Note: Optional φ80 mast mount kit (Type: OP24-5, Code no.: 005-954-510) is
required to fix the GPS/VHF combined antenna to the mast (φ60 - 80).
5
Mounting procedures
1. Dismount the bottom cover, cut the cable-tie inside the unit and take out the
coaxial connector attached to the combined box.
2. Loosen four screws to loosen whip antenna fixture and pull out the coaxial
connector coming from the combined box through the hole in the whip antenna
fixture.
3. Connect the coaxial connector to the whip antenna base and wrap the junction
part of the whip antenna with vulcanizing tape and then vinyl tape for
waterproofing.
4. Insert the whip antenna from the top of the combined antenna.
5. Secure the whip antenna with whip antenna fixture.
6. Using a new plastic band (supplied), secure the cables and coaxial connector
inside the antenna case.
7. Mount the bottom cover.
8. Fix the GPS/VHF combined antenna to the ship’s stanchion (40 to 50 mm
diameter) with antenna fixing brackets, flat washers and hex. nuts.
Note: Coat the exposed parts of bolts and nuts with silicon sealant.
Whip antenna fixture
Loosen four screws.
(M5x16)
Antenna fixing bracket
Combined box
Bottom cover
GPS/VHF Combined antenna
6
The top of the stanchion come
into contact with the flange.
Stanchion
Installing distributor unit DB-1
The length of the cable between the distributor unit and transponder unit is 1 m so
locate the distributor unit within 1 m from the transponder unit. Fix the distributor
unit on the bulkhead, facing the cable entrance downward. Remove the lid of the
distributor unit and secure the unit with two tapping screws.
Tapping screw
(4x30)
Note: Be sure no foreign material or water enters the distributor unit.
7
1.2 Transponder Unit
The transponder unit can be installed on a desktop or flush mounted in a panel.
Install it on the chart table or near the steering place, referring to the outline
drawing.
When selecting a mounting location for the transponder, keep the following in mind:
• Keep the transponder out of direct sunlight.
• The temperature and humidity should be moderate and stable.
(Operating temperature range: -15°C to +55°C)
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Keep the unit away from electromagnetic field generating equipment such as
motor, generator.
• For maintenance and checking purposes, leave sufficient space at the sides and
rear of the unit and leave slack in cables. Refer to the outline drawing.
• A magnetic compass will be affected if the unit is placed too close to it. Observe
the following compass safe distances to prevent disturbance to the magnetic
compass:
Standard compass: 1.0 meters
Steering compass: 0.6 meters
Desktop mounting
1. Remove two hex. bolts from the lower part of the transponder unit and dismount
the mounting base.
Remove two hex. bolts.
2. Fix the mounting base to the desktop with four tapping screws (6x20: supplied)
or hex. bolts.
120 mm
120 mm
φ8
Front
Service clearance
more than 130 mm
Mounting base
3. Place the transponder unit on the mounting base and secure it with two hex.
bolts.
8
Flush mounting
Optional flush mount kit A or B is required for flush mounting. For mounting
dimensions, refer to the outline drawing at the back of this manual.
Flush mount kit A:
Type OP24-1
Code no. 005-950-740
Name
Type
Code no.
Qty
1
Cosmetic panel
24-003-2811
100-299-540
1
2
+Tapping screw
5x25
000-802-082
4
1. Cut out a hole in the mounting location, referring to the outline drawing.
2. Remove two hex bolts to dismount the mounting base.
3. Remove six hex bolts from the bottom of the transponder unit to dismount the
mounting pedestal.
4. Set the transponder unit to the cosmetic panel and fix them with six hex bolts.
5. Set the assembly (transponder unit and cosmetic panel) to the hole and fix it
with four tapping screws (5x25).
Flush mount kit B:
Type OP24-2
Name
Code no. 005-950-750
Type
Code no.
Qty
1
Mounting bracket
24-003-2821
100-299-550
1
2
Hex bolt
M5x25
000-862-125
6
3
Hex nut
M5
000-863-108
6
4
Flat washer
M5
000-864-128
6
5
Spring washer
M5
000-864-258
6
1. Cut out a hole in the mounting location, referring to the outline drawing.
2. Dismount the mounting base and mounting pedestal from the transponder unit.
3. Set the transponder unit to the hole. Using six hex bolts, attach the mounting
bracket at the bottom of the transponder unit from the rear of the flush mounting
panel.
4. Fix with six sets of hex bolt, nut, flat washers and spring washers from the rear
of the flush mounting panel.
9
1.3 Junction Box
Mount the junction box where the junction box is protected from rain and water
splash.
Mounting
1. Open the lid of the junction box and fix the junction box with four tapping screws
(5x20). Avoid bundling the 3.3 m cable of the junction box together with any
power cable. This causes malfunction.
2. Connect cables to the terminal board, referring to Chapter 2 and 3.
3. Fix the lid after connecting external equipment.
4. Clamp the cable with several U-type cable clamps (local supply) at suitable
intervals.
Clamp the cable with
U-type cable clamps.
Fixing holes
(5x20 tapping screws)
Cable entry
Cable clamp
10
1.4 Power Supply (option)
The length of the power cable between the power supply and the transponder unit
is 3.5 m. Keep this length in mind when selecting a mounting location. A longer
cable should not be used – voltage drop will result, affecting performance.
When selecting a mounting location for the unit, keep the following in mind:
•
•
•
•
•
Keep the unit out away from areas subject to water splash.
Locate the unit away from exhaust pipes and vents.
The mounting location should be well ventilated.
Mount the unit where shock and vibration are minimal.
A magnetic compass will be affected if the unit is placed too close to it. Observe
the following compass safe distances to prevent disturbance to the magnetic
compass:
Steering compass: 0.6 m
Standard compass: 0.9 m
Fix the unit with four tapping screws (4x16) to a desktop or the deck as shown in
the figure below. It is not necessary to open the cover.
1.5 Pilot Plug (option)
The pilot plug should be mounted near where the pilot steers the ship. This plug is
used to connect a PC to display AIS information for use by the pilot. Refer to the
outline drawing at the back of this manual for mounting dimensions.
11
2. WIRING
Connect the equipment, referring to the interconnection diagram at the back this
manual.
GPS Antenna
GPA-017S
GSC-001
GPS/VHF Conbined
Antenna GVA-100
150M-W2VN
Either one
0.6 m
Distributor unit
DB-1
***
0.9 m
***
***
RG-10/UY
Attached to Distributor
(approx. 1m)
RG-10/UY
8D-FB-CV, 30 m/50 m: Option
RG-10/UY: Local supply
GPS ANT VHF ANT
AUX-1
LAN
AUX-2
: ground is not required.
LAN cable
(category 4 or higher)
PC
TTYCS-1Q**
AD-10 IN
AD-100
Gyrocompass
Power Supply
PR-240-CE
AC DC DC
IN IN OUT
1.5 sq
DPYC-1.5**
MJ-A3SPF0013-035 (3.5 m) *
EXTRA I/O
Transponder
unit
FA-100
Approx. 3.3 m
AIS sentence out
(4800 bps)
Pilot Plug
Alarm out
GPS receiver
Heading sensor
Speed sensor or ROT
Beacon receiver
AIS data In/Out
Ship’s mains
100-115/200-230 VAC
24 VDC
1φ, 50/60 Hz
12-24 VDC
(Connect to the alternative
power source.)
Junction Box
CB-100
TTYCS-1Q** or TTYCS-4**
: Standard
: Option
: Local Supply
*: If the ship’s mains is 12 VDC, cable length should be less than 50 cm.
EXTRA IO port: Outputs AIS sentence (4800 bps).
AUX-1, AUX-2 port: Not used.
12
**: DPYC-1.5, TTYCS-1Q and TTYCS-4 are Japan Industry Standard cable.
Use them or the equivalents.
DPYC-1.5
TTYCS-1Q (Four core twisted)
Armor
Armor
Sheath
Sheath
φ = 11.7 mm
Conductor
S = 1.5 mm 2
φ = 1.56 mm
φ = 11.3 mm
Shield
Conductor
S = 0.75 mm2
φ = 1.11 mm
TTYCS-4 (Four twisted pairs)
φ = 18.5 mm
Sheath
Armor
Sheath
Shield
Conductor
S = 0.75 mm 2
φ = 1.11 mm
***: Waterproofing connectors
Wrap connector with vulcanizing tape and then vinyl tape. Bind
the tape end with a cable-tie.
Waterproofing connector
13
Cable Connection at Junction Box
Cable fabrication
Armor
Sheath
Shield
5 to 6 mm
30
Clamp here by cable clamp.
Connection
1
2
3
Core 5-6 mm
Procedure
1. Insert driver from direction 1 .
2. Tilt slightly toward 2 .
3. Insert cable core to 3 .
14
3. INPUT/OUTPUT SIGNAL
3.1 Inputs from Sensors
There are three input ports (SENSOR 1, 2 and 3) which are based on the IEC
61162-1/2. The protocol is RS422. If there is no HDT signal from a gyrocompass,
connect the gyrocompass signal (Synchro or step signal) to the “AD-10 IN” port
(D-sub 9 pins) of the transponder unit via the FURUNO A/D Converter AD-100 (See
page 16).
TB1 in the junction box
1
TD3-A
2
TD3-B
3
GND ISO
4
RD3-A
5
RD3-B
6
GND ISO
7
TD2-A
8
TD2-B
9
GND ISO
SENSOR 3 (EXT GPS IN)
TTYCS-1Q
(4 cores twisted)
GPS navigator only
Isolated GND
SENSOR 2
TTYCS-1Q
10 RD2-A
Heading Signal (HDT)
11 RD2-B
12 GND ISO
Isolated GND
13 TD1-A
14 TD1-B
15 GND ISO
16 RD1-A
SENSOR 1
TTYCS-1Q
Speed Signal (SOG)
17 RD1-B
18 GND ISO
19 TD5-A
Isolated GND
TTYCS-1Q
20 TD5-B
21 GND
23 RD5-B
DGPS
Beacon
Receiver
24 GND
GND 0V
22 RD5-A
15
3.2 Input/Output of AIS Signal
Three input/output ports are provided for RS-422 protocol, based on the IEC
61162-1/2. Data transmission rate is selectable from 4800 bps and 38.4 kbps.
Normally, Radar/ECDIS/PC, etc. are connected to these ports to exchange data
with the AIS. PC standard protocol RS-232C is also provided in the D-sub port of
the transponder unit.
TB1 in the junctionbox
TTYCS-4
25 TD4-A
RD-A
26 TD4-B
RD-B
27 GND ISO
Isolated GND
L/R (INMARSAT) or
28 RD4-A
ECDIS/RADAR
29 RD4-B
TD-A
TD-B
30 GND ISO
Isolated GND
31 TD6-A
TTYCS-4
RD-A
32 TD6-B
RD-B
33 GND ISO
Isolated GND
34 RD6-A
TD-A
TD-B
Isolated GND
35 RD6-B
36 GND ISO
37 TD8-A
TTYCS-4
RD-A
38 TD8-B
RD-B
39 GND ISO
Isolated GND
40 RD8-A
42 GND ISO
TD-A
TD-B
Isolated GND
43 TD (232C)
Rx port
44 RD (232C)
Tx port
41 RD8-B
21 GND
EXTRA I/O
PC I/O
GND
TTYCS-1Q
Note: For TD (232C) and RD (232C), use one twisted pair for TD and one twisted
pair for RD, separately. Use pin #21 for SG.
16
3.3 Input of Gyrocompass Signal
If the gyrocompass has no HDT signal, the AD-10 format (FURUNO format) signal
can be input via the FURUNO A/D Converter AD-100. Connect the AD-100 to the
“AD-10 IN” port (D-sub 9 pin) on the rear panel of the transponder unit.
FA-100
AD-10 IN
DATA-H >1>
DATA-L >2>
CLOCK-H >3>
CLOCK-L >4>
>8>
GND
>9>
F.GND
Twisted pair cable (Example: TTYCS-1Q cable)
to DATA terminal of AD-100
Note: Set data output interval for 200 ms (instead of 25 ms) by internal jumper
inside the AD-100.
3.4 Alarm Signal Output
The FA-100 generates an alarm signal (relay contact signal) for hardware failure
such as transmitter block or sensor abnormality. For details of alarm type, see the
operator’s manual.
Two kinds of contact signals, on (normal closure) or off (normal open), are output,
and are selected at the junction box CB-100 according to the alarm generator
connected. The maximum current and voltage of the contact are 1 A, 125 VAC and
60 VDC. Normally connect to the NC (normal close) between #45 and #47.
TB-1 in the junction box
45 AOL
46 AOH
#45-#47: Normal Close
#46-#47: Normal Open
47: common line
47 AOC
17
3.5 LAN Input/Output
The FA-100 supports Ethernet based on LAN. Its protocol is 10BASE-T and the
transmission rate is 10 Mbps. To connect the FA-100 with other equipment (such as
a PC), use a LAN cable category 4 or higher with shield (SDT). Connect it to the
PC with an RJ-45 connector, and connect to the FA-100 with a D-sub 9 pin
connector, to avoid noise leakage. To use a commercial LAN cable, remove one
connector and solder a D-sub 9 pin connector, supplied in the installation materials.
RJ-45 (Category 4 and higher, SDT)
FA-100
LAN (10B-T)
TD+
TDRD+
RDGND
F.GND
Twisted pair cable
3
6
1
2
>1>
>2>
>3>
>4>
>8>
>9>
RD+
RDTD+
TD-
3.6 Pilot Plug
Use the twisted cable TTYCS-4 between the junction box and the pilot plug. The
cable between the PC and the pilot plug should be prepared by the ship’s pilot.
Pilot plug
Junction box
Terminal board
37
38
39
40
41
42
TB1
TD A
TD8-A
TD8-B
GND ISO
RD8-A
RD8-B
GND ISO
TD B
RD-A
RD-B
SHIELD
3mm Crimp-on lug
18
J1
TTYCS-4
>1>
>2>
>3>
>4>
>5>
>6>
>7>
>8>
>9>
PC
206486-1
(AMP)
3.7 Jumper Setting in the Junction Box
Each RS-422 RX line (on the PCB 24P0031 in the junction box) has a jumper block
with 240 ohms termination resistor. The junction box is shipped with all jumper
blocks connected between the #3 and #4 terminals pins, terminating RX lines with
240 ohms. Assuming that an external equipment has the output voltage of ±5 V,
more than 21 mA of output current is required.
If multiple equipment are connected to an output port of an external equipment,
change to jumper block setting to between the #1 and #2 pins to reduce the load on
the FA-100. Then, the input impedance of the RS-422 RX lines in the FA-100
becomes more than 2.4 k ohms.
We recommend that you leave the connection of the jumper block between #3 and
#4 pins if only the FA-100 is connected to an external equipment.
Jumper block (6 pcs)
2
Factory setting: #3-#4
4
1
3
19
3.8 Input/Output Sentences
1) SENSOR 1, SENSOR2, and SENSOR3 ports
These ports can receive IEC61162-1/2 standard data. The transmission rate of
sensor 1, 2, and 3 is selectable from 4800 bps and 38.4 kbps through the menu.
Input sentences are as follows:
$xxDTM, $xxGBS, $xxGGA, $xxGLL, $xxGNS, $xxHDT
$xxOSD, $xxRMC, $xxROT, $xxVBW, $xxVTG
Note: The talker of the underlined sentences has priority as
follows:
GN>GP>GL>LC>IN
Other sentences disregard talker.
2) PC I/O, LR or ECDIS/RADAR, EXTRA I/O and EXTRA 1 I/O ports
These ports can receive or output IEC61162-1/2 standard data. The transmission
rate of signals is selectable from 4800 bps and 38.4 kbps through the menu. The
transmission rate of the EXTRA IO port signal is fixed to 4800 bps.
Input sentences are as follows:
$xxABM, $xxACA, $xxACK, $xxAIR
$xxBBM, $xxDTM, $xxGBS, $xxGGA
$xxGLL, $xxGNS, $xxHDT, $xxLRF
$xxLRI, $xxOSD, $xxRMC, $xxROT
$xxSSD, $xxVBW, $xxVSD, $xxVTG
Note: The talker of the underlined sentences has priority as
follows:
GN>GP>GL>LC>IN
Other sentences disregard talker.
Output sentences are as follows:
$AIABK, $AIACA, $AIALR, $AILRF,
$AILR1, $AILR2, $AILR3, $AITXT,
$AIVDM, $AIVDO
20
3.9 Changing Ship’s Mains Specifications
The power supply PR-240-CE is shipped ready for connection to a 200-230 VAC
ship’s mains. If the ship’s mains is 100 VAC – 115 VAC, change the tap connection
and terminal board connection as below. Attach label supplied as accessories to
the punch mark in the front panel according to the ship’s mains.
Ship’s mains
Tap connection
Terminal board
connection #1 & #2
100-115 VAC
SEL 115 V
b
200-230 VAC
SEL 230 V
a
100-115 VAC
200-230 VAC
1
White
1
White
2
Black
2
Black
3
3
Punch mark
(a)
(b)
Front
SEL
115 V
1
2
3
4
5
6
7
8
SEL
230 V
Terminal board connection
Heat sink
Tap connection (Pull out to remove)
Top view (Cover removed)
21
4. SETTING AND ADJUSTMENT
After installing the equipment, set up the own ship’s static information (MMSI, IMO
number, ship’s name, call sign, type of ship and GPS antenna position). Also, set
up the system settings.
4.1 Setting MMSI, IMO No., Name and Call Sign
1. While holding down the [0] key, press the [POWER] key.
2. After the following message appears, release the [0] key. (It takes several
seconds before the message appears.)
NOW STARTING
CHECKING MEMORY
3. After the following window appears, enter the password. Note that the password
is known by only the FURUNO dealer.
[ENTER PASSWORD]
PASSWORD:
4. Press the [ENT] key to display the SET MMSI & IMO# window.
Asterisk marks
current selection.
[SET MMSI & IMO#]
MMSI :
IMO#
:
NAME :
C.SIGN :
SET: [ENT]
5. Enter ship’s MMSI (Maritime Mobile Service Identity) in nine digits.
6. Press the [NEXT] key to select IMO#.
7. Enter ship’s IMO number in nine digits. If the IMO number has 7 digits, enter “0”
twice followed by IMO#. IF the ship has no IMO number, enter all zeroes.
8. Press the [NEXT] key to select NAME.
22
9. Enter ship’s name, using up to 20 alphanumeric characters. To switch between
alphabet and numerical character, press the [SFT] key. To enter an alphabet,
press corresponding key several times until desired letter is displayed. For
example, if you press the [2] key continuously, the character A, B and C appear
cyclically. If you want to enter the same letter or an other letter with the same
key (for example, AA or AC), press the [6] key while pressing the [SFT] key, to
send the cursor to the next position.
10. Press the [NEXT] key to select C.SIGN.
11. Enter call sign, using up to seven alphanumeric characters.
12. Press the [ENT] key to register data. The INIT SETTINGS sub-menu appears.
23
4.2 Setting GPS Antenna Position and
Ship’s Type
1. In the INIT SETTING sub-menu, press the [6] key to open the SET ANTENNA
POS window.
SET ANTENNA POS
1 INTERNAL ANT POS
2 EXTERNAL ANT POS
SET ANTENNA POS window
2. With 1 selected, press the [ENT] key. The 1 is for entering internal GPS antenna
position and 2 is for external GPS which is connected to the AIS.
[INTERNAL ANT POS]
A
B
C
D
A: 000 m
B: 000 m
C: 00 m
D: 00 m
INTERNAL ANT POS window
3. Enter locations of GPS antenna, by using the numeric keys and the [NEXT] key,
and finally press the [ENT] key.
A: Distance from bow to GPS antenna position
B: Distance from stern to GPS antenna position
C: Distance from port to GPS antenna position
D: Distance from starboard to GPS antenna position
4. Enter external GPS antenna position similar to how you entered internal GPS
antenna position.
5. Press the [MENU] key to return to the INIT SETTINGS sub-menu.
6. Press the [4] key to display the SET TYPE&CREW window.
[SET TYPE&CREW]
CREW
: 0012
TYPE CLASS : A
TYPE NO.
: 0
TYPE NAME
TYPE CLASS cannot
be changed.
(A = IMO type)
SET TYPE&CREW window
24
7. Press the [NEXT] key to select TYPE NO.
Confirm type of ship with ship’s captain before setting it.
8. Press the [2], [4], [6] or [8] key as appropriate to select your ship’s type,
referring to the list on below.
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
WIG
WIG
WIG
WIG
WIG
WIG
WIG
WIG
WIG
WIG
FISHING
TOWING
ALL SHIPS OF THIS TYPE
CARRYING DG, HS, OR MP(A)
CARRYING DG, HS, OR MP(B)
CARRYING DG, HS, OR MP(C)
CARRYING DG, HS, OR MP(D)
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
NONE
ALL SHIPS OF THIS TYPE
CARRYING DG, HS, OR MP(A)
CARRYING DG, HS, OR MP(B)
CARRYING DG, HS, OR MP(C)
CARRYING DG, HS, OR MP(D)
FUTURE USE
FUTURE USE
FUTURE USE
FUTURE USE
NONE
60 PASSENGER SHIPS ALL SHIPS OF THIS TYPE
61 PASSENGER SHIPS CARRYING DG, HS, OR MP(A)
62 PASSENGER SHIPS CARRYING DG, HS, OR MP(B)
63 PASSENGER SHIPS CARRYING DG, HS, OR MP(C)
64 PASSENGER SHIPS CARRYING DG, HS, OR MP(D)
65 PASSENGER SHIPS FUTURE USE
66 PASSENGER SHIPS FUTURE USE
67 PASSENGER SHIPS FUTURE USE
68 PASSENGER SHIPS FUTURE USE
69 PASSENGER SHIPS NONE
70 CARGO SHIPS
ALL SHIPS OF THIS TYPE
71 CARGO SHIPS
CARRYING DG, HS, OR MP(A)
72 CARGO SHIPS
CARRYING DG, HS, OR MP(B)
73 CARGO SHIPS
CARRYING DG, HS, OR MP(C)
74 CARGO SHIPS
CARRYING DG, HS, OR MP(D)
75 CARGO SHIPS
FUTURE USE
76 CARGO SHIPS
FUTURE USE
77 CARGO SHIPS
FUTURE USE
78 CARGO SHIPS
FUTURE USE
79 CARGO SHIPS
NONE
ALL SHIPS OF THIS TYPE
80 TANKER
81 TANKER
CARRYING DG, HS, OR MP(A)
LENGTH OF THE TOW EXCEEDS 200M OR BREADTH EXCEEDS 25M 82 TANKER
CARRYING DG, HS, OR MP(B)
ENGAGED IN DREDGING OR UNDERWATER OPERATIONS 83 TANKER
CARRYING DG, HS, OR MP(C)
ENGAGED IN DIVING OPEARATIONS
84 TANKER
CARRYING DG, HS, OR MP(D)
ENGAGED IN MILITARY OPEARATIONS
85 TANKER
FUTURE USE
SAILING
86 TANKER
FUTURE USE
PLEASURE CRAFT
87 TANKER
FUTURE USE
FUTURE USE
88 TANKER
FUTURE USE
FUTURE USE
89 TANKER
NONE
ALL SHIPS OF THIS TYPE
90 OTHER TYPE OF SHI ALL SHIPS OF THIS TYPE
HSC
HSC
CARRYING DG, HS, OR MP(A)
91 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(A)
HSC
CARRYING DG, HS, OR MP(B)
92 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(B)
HSC
CARRYING DG, HS, OR MP(C)
93 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(C)
HSC
CARRYING DG, HS, OR MP(D)
94 OTHER TYPE OF SHI CARRYING DG, HS, OR MP(D)
HSC
FUTURE USE
95 OTHER TYPE OF SHI FUTURE USE
HSC
FUTURE USE
96 OTHER TYPE OF SHI FUTURE USE
HSC
FUTURE USE
97 OTHER TYPE OF SHI FUTURE USE
HSC
FUTURE USE
98 OTHER TYPE OF SHI FUTURE USE
HSC
NONE
99 OTHER TYPE OF SHI NONE
PILOT
WIG: Wing in ground
SEACH AND RESCURE VESSELS
HSC: High speed craft
TUGS
DG: Dangerous goods
PORT TENDERS
VESSELS WITH ANTI-POLUUTION FACILITIES OR EQUIPMENT
LAW ENFOREMENT VESSELS
SPARE-FOR ASSIGNMENTS TO LOCAL VESSELS
SPARE-FOR ASSIGNMENTS TO LOCAL VESSELS
MEDICAL TRANSPORTS
SHIPS ACCORDING TO RESOLUTION NO 18
HS: Harmful substances
MP: Marine pollutants
0-9: Undefined
9. Press the [ENT] key to return to the INIT SETTING sub-menu.
25
10. Press the [MENU] key. The SAVE confirmation window appears.
SAVE ?
YES
NO
CANCEL
SAVE confirmation window
11. With YES selected, press the [ENT] key to save the data.
4.3 System Settings
1. Press the [MENU] key to open the main menu.
2. Press the [6] key to open the SYSTEM SETTINGS sub-menu.
[SYSTEM SETTINGS]
1 SET I/O PORT
2 SET CHANNEL
3 SET LR MODE
4 SET OTHER I/O
5 SET BUZZER
SYSTEM SETTINGS sub-menu
3. Press the [1] key to display the SET I/O PORT sub-menu.
[SET I/O PORT]
1 I/O SPEED
2 I/O FUNCTION
3 I/O PRIORITY
4 SET LAN (IP ADDR)
SET I/O PORT sub-menu
4. Press the [1] key to display the I/O SPEED window.
[I/O SPEED]
PC I/O : 38.4 k
SNSR1: 38.4 k
SNSR2: 38.4 k
SNSR3: 38.4 k
+++1 2+ -
[NEXT] key
[I/O SPEED]
LR
:
BCON
:
EXTRA1 :
XTRA I/O :
[SFT] +[NENT]
key
I/O SPEED window
26
38.4 k
4800
38.4 k
4800 1
++++2-
5. Select the appropriate data transmission rate from 4800 bps and 38.4 kbps for
PC I/O, SNSR 1, SNSR 2, SNSR 3, LR, BCON (beacon receiver), EXTRA1 and
EXTRA2, by pressing the [SFT] key. To select each item, press the [NEXT] key.
To go backward, press the [NEXT] key while pressing the [SFT] key.
6. Press the [ENT] key to return to the SET I/O PORT sub-menu.
7. Press the [2] key to display the I/O FUCTION window.
[I/O FUNCTION]
PORT LR: EXT DISP + -
I/O FUNCTION window
8. Press the [SFT+/-] key to select EXT DISP or LR, depending on equipment
connected.
EXT DISP: External display, such as radar, ECDIS
LR: Long range communication, such INMARSAT communication equipment
9. Press the [ENT] key to return to the SET I/O PORT sub-menu.
10. Press the [3] key to display the I/O PRIORITY window.
[I/O PRIORITY]
1 L/L
COG
2 HDG
3 ROT
4 AIS
SOG
I/O PRIORITY window
11. Press the [1] key to display the L/L COG SOG window.
[L/L COG SOG]
SN2: 2
SN1: 1
SN3: 3
LR : 5
EX1 : 4
LAN: 7
PC : 6
DEFAULT: [CLR]
L/L/COG/SOG PRIORITY window
27
12. Set L/L position, COG and SOG data priority with the numeric keys according to
sensors connected.
COG: Course over ground
SOG: Speed over ground
13. Press the [ENT] key to return to the I/O PRIORITY window.
Note: If you have entered 8, 9 or the same value for more than one item at step
12, the following error message appears. In this case, press the [ENT]
key and set the priority correctly.
[ERROR]
CAN NOT INPUT
SAME VALUE !
ESC: [ENT]
[ERROR]
OUT OF RANGE !
PRIORITY: 1-7
ESC: [ENT]
ERROR message
14. Set the priority for HDG and ROT similar to how you did for “L/L COG SOG”.
The priority of heading data entered from the AD-10 IN port is the lowest.
15. To set the priority of AIS, press the [4] key to choose AIS.
[AIS]
+RESPONSE:PC
-------------------+EX1 : ENBL
+LR : ENBL
+
PC : ENBL
+LAN: ENBL
DEFAULT: [CLR]
AIS PRIORITY setting window
16. With RESPONSE selected, press the [SFT] key to select PC, NONE, LAN, EX1
or LR as appropriate.
Set an output port for response from other party after you transmit messages or
interrogation from the PC, ECDIS, LR, or LAN.
NONE
: No output for response
PC
: Output to PC I/O port
LAN
: Output to LAN port
LR
: Output to LR or ECDIS/RADAR port
EX1
: Output to EXTRA1 port
The PC I/O port provides RS-422 and RS-232C terminals. For example, to
connect a PC for pilot, connect it to the RS-422 terminal and set 34.8 Kbps for bit
rate on the PC I/O option in the I/O SPEED window.
17. Press the [NEXT] key to select EX1, LR, PC or LAN.
18. Press the [SFT] key to select ENBL (enable) or DSBL (disable) as appropriate.
This setting is for communication between FA-100 and each external equipment.
“DSBL” disables communication with selected item.
19. Press the [ENT] key and then [MENU] key to return to the SET I/O PORT
sub-menu.
28
20. Press [4] key to display the SET LAN (IP ADRS) window.
[SET LAN (IP ADRS)]
IP ADDRESS:
000-000-000-000
SUB NET MASK:
000-000-000-000
PORT NO. 10000
SET LAN (IP ADDR) window
21. If the FA-100 is connected to a network, enter IP address, sub net mask and
port number with the numeric keys and the [NEXT] key.
22. Press the [ENT] key and then the [MENU] key to return to the SYSTEM
SETTINGS sub-menu.
23. Press the [4] key to display the SET OTHER I/O window.
[SET OTHER I/O]
AD-10: DSBL
ROT : 01 SEC
+-
SET OTHER I/O window
24. Select or set other I/O as follows.
1) AD-10: Select ENBL to use AD-10 format gyrocompass signal.
2) ROT: Set smoothing time (1 to 10 seconds) of the ship’s rate of turn if you are
using a ROT meter. This time is used to smooth the variations of data from the
AD-100 for calculation of ROT.
3) Press the [ENT] key to register setting. The display returns to the SYSTEM
SETTINGS sub-menu.
25. Press the [MENU] key. The following confirmation window appears.
SAVE ?
YES
NO
CANCEL
SAVE confirmation window
26. Select YES and press the [ENT] key. The main menu appears.
29
This page is intentionally left blank.
A-1
24AA-X-9854 -1
PACKING LIST
1/1
FA-100-J/E,FA-100-J/E-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
FA-100
トランスポンダ部
1
TRANSPONDER UNIT
000-053-889 **
工事材料
INSTALLATION MATERIALS
CP24-00102
XM2S-0912
コネクタフード(XM2)
1
HOUSING CASE
000-145-422
MJ-A3SPF0015-035
ケーブル組品MJ
1
CABLE ASSY.
000-137-340
XM2A-0901
コネクタ(XM2)
1
CONNECTOR(XM2)
000-111-785
図書
DOCUMENT
IMJ-44170-*
装備要領書
1
INSTALLATION MANUAL
000-809-324 **
OMJ-44170-*
取扱説明書
1
OPERATOR'S MANUAL
000-809-322 **
1.コ-ド番号末尾の[**]は、選択品の代表型式/コートを表します。
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
24AA-X-9854
A-2
24AA-X-9851 -4
PACKING LIST
1/1
CB-100-A、CB-100-A-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
CB-100-A
接続箱
1
JUNCTION BOX UNIT
000-053-873 **
工事材料
INSTALLATION MATERIALS
CP05-08701
5X20 SUS304 1シュ
+トラスタッピンネジ
4
+TAPPING SCREW
000-802-081
1.コ-ド番号末尾の[**]は、選択品の代表型式/コートを表します。
DOUBLE ASTERISK DENOTES COMMONLY USED EQUIPMENT.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
24AA-X-9851
A-3
PACKING LIST
24AA-X-9853 -3
1/1
GVA-100
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
GVA-100
複合空中線部
1
GPS/VHF COMBINED ANTENNA
000-053-810
工事材料
INSTALLATION MATERIALS
CP24-00141
N-P-8DFB
コネクタ(N)
座金付き
2
CONNECTOR
000-140-463
CV-200HT
コンベックス
2
PLASTIC BAND
000-809-226
24-003-3015-0
アンテナ取付金具
2
ANTENNA FIXING BRACKET
100-302-670
M8 SUS304
ミガキ平座金
4
FLAT WASHER
000-864-130
M8 SUS304
六角ナット 1種
8
HEX.NUT
000-863-110
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
24AA-X-9853
A-4
工事材料表
CODE NO.
004-365-780
TYPE
CP20-01111
20AG-X-9403 -1
1/1
マスト取付金具
MAST FIXTURE
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
略 図
OUTLINE
パイプ
1
型名/規格
DESCRIPTIONS
1
PIPE
取付補助金具
20-007-3012-1
1
CODE NO.
3
100-183-262
INSTALLING SPACER
パーカークランプ
用途/備考
REMARKS
20-007-3011-2
CODE NO.
2
数量
Q'TY
100-183-271
NO.6348 SUS303
2
HOSE CLAMP
CODE NO.
000-805-906
20AG-X-9403
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-5
PACKING LIST
24AA-X-9852 -5
1/1
PR-240-CE
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
PR-240-CE
AC-DC電源
1
POWER SUPPLY UNIT
000-053-879
工事材料
INSTALLATION MATERIALS
PR-240-CE電源変更手順書
CP24-00151
C52-00205-A
1
POWER MODIFICATION PROCEDURES
000-147-013
24-003-4101-3
デンゲンハリマーク
1
POWER LABEL
100-299-773
4X16 SUS304 1シュ
+トラスタッピンネジ
4
+TAPPING SCREW
000-802-080
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
24AA-X-9852
A-6
20AG-X-9404 -1
CODE NO.
1/1
TYPE
工事材料表
GP-80,GP-90,SC-55,GP-3500/F GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
アンテナケーブル組品
1
略 図
OUTLINE
型名/規格
DESCRIPTIONS
選択 TO BE SELECTED
1
CODE NO.
2
用途/備考
REMARKS
8D-FB-CV *30M*
ANTENNA CABLE ASSY.
ケーブル組品
数量
Q'TY
000-111-547
選択 TO BE SELECTED
8D-FB-CV *50M*
1
CABLE ASSY.
CODE NO.
000-117-599
20AG-X-9404
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-7
CODE NO.
004-372-420
TYPE
CP20-01701
20AG-X-9405 -1
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
変換ケーブル組品
1
略 図
OUTLINE
型名/規格
DESCRIPTIONS
2
CONVERT CABLE ASSY.
ビニールテープ
1
VINYL TAPE
コネクタ(N)
000-835-215
N-P-8DFB
1
CONNECTOR
CODE NO.
絶縁テープ
4
000-123-809
NO360 02X19X10000
クロ エスロン
CODE NO.
3
用途/備考
REMARKS
NJ-TP-3DXV-1
CODE NO.
2
数量
Q'TY
000-111-549
Uテープ 0.5X19X5M
1
SELF-BONDING TAPE
CODE NO.
000-800-985
20AG-X-9405
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-8
工事材料表
CODE NO.
004-365-780
TYPE
CP20-01111
20AG-X-9403 -1
1/1
マスト取付金具
MAST FIXTURE
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
略 図
OUTLINE
パイプ
1
型名/規格
DESCRIPTIONS
1
PIPE
取付補助金具
20-007-3012-1
1
CODE NO.
3
100-183-262
INSTALLING SPACER
パーカークランプ
用途/備考
REMARKS
20-007-3011-2
CODE NO.
2
数量
Q'TY
100-183-271
NO.6348 SUS303
2
HOSE CLAMP
CODE NO.
000-805-906
20AG-X-9403
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
Oct. 21,'02
D-2
Oct. 21,'02
D-3
D-4
Sep.29'05
D-4a
May 20 '03
D-5
Feb.22'05
Jan. 9,'03
D-6
Jan. 9, '03
D-7
Mar.11'04
H.Hayashi
D-8
D-9
Feb.02'05
D-10
Nov.28'03
Y. Hatai
D-11
Oct.02'03
D-12
1
2
3
トランスポンダ部
TRANSPONDER UNIT
FA-100
選択
SELECT
GPSアンテナ
GPS ANTENNA
GPA-017S
OR
GSC-001
複合空中線部
GPS/VHF ANTENNA
GVA-100
150M-W2VN
*2
OR
FAB-151D
NJ-TP-3DXV-1
1m,φ5.3
0.2m
N-J-3 0.8m
N-P-8DFB
B
船内主電源及び
非常電源
SHIP'S MAIN AND
EMERGENCY SOURCE
12-24VDC
C
100-115/200-230VAC *DPYC-1.5
φ1,50/60Hz
D
M-P-7
M-P-7
NJ-TP-3DXV-1
1m,φ5.3
N-P-8DFB
N-J-3 1m
分配器
DISTRIBUTOR
DB-1
1m
GPS-ANT
J2
VHF-ANT
TNC-P-3
1m
GPS-ANT
AC/DC電源ユニット
AC/DC POWER SUPPLY
PR-240-CE *2 UNIT
POWER
MJ-A3SPFD
J1(FM-C3MR)
シロ WHT
1 (+)
クロ BLK
2 (-)
3 GND
EXTRA1 I/O TD6-A
IEC61162-1/2 TD6-B
RD6-A
RD6-B
21
22
23
24
PC I/O TD8-A
TD8-B
(RS-422) RD8-A
RD8-B
TD
(RS-232C)
RD
ALARM OUT ALOL
(CONTACT SIG.) ALOH
ALOC
1PPSIN
NC
GND
FG
25
26
27
28
29
30
31
32
33
34
35
36
37
PE, V-2.0SQ
保護アース
EXTRA I/O
J2
IEC61162-1 TD7-A
TD7-B
1
2
GND
FG
8
9
LAN(10B-T)
J3
IEC61162-4 LATX-H
(10BASE-T) LATX-L
LARX-H
LARX-L
GND
FG
1
2
3
4
8
9
AD-10 IN
J4
GDAT-H
*6 GDAT-L
GCK-H
GCK-L
GND
FG
1
2
3
4
8
9
AUX-1
J5
LOG
LOG-G
PRTX
PRRX
GND
FG
1
2
6
7
8
9
AUX-2
J6
GPEXT-A
GPEXT-B
GPEXR-A
GPEXR-B
GND
FG
1
2
3
4
8
9
24P0020
DC OUT (+)
(-)
注記
*1)造船所手配。
*2)オプション。
*3)外部GPS受信機からのL/Lデータ入力が必要。
*4)SOG、COGが外部GPSから出力可能な場合は不要。
*5)ROTは接続可能な場合のみ。
*6)AD-10フォーマット(GYRO-IEC61162がないときに必要)
*7)12V仕様の場合、ケーブル最大長は0.5m。
*8)AMP社製。
J1
ANT
E
RTCM SC-104
5
接続箱 CB-100
J1 JUNCTION BOX
1
TD3-A 1
2
TD3-B 2
GNDISO 3
3
4
RD3-A 4
5
RD3-B 5
GNDISO 6
6
7
TD2-A 7
8
TD2-B 8
9
GNDISO 9
10
RD2-A 10
RD2-B 11
GNDISO 12
J2
1
TD1-A 13
2
TD1-B 14
3
GNDISO 15
4
RD1-A 16
5
RD1-B 17
6
GNDISO 18
7
TD5-A 19
8
TD5-B 20
9
GND 21
10
RD5-A 22
11
RD5-B 23
12
GND 24
TD4-A 25
TD4-B 26
J3
1
GNDISO 27
2
RD4-A 28
3
RD4-B 29
4
GNDISO 30
5
TD6-A 31
6
TD6-B 32
7
GNDISO 33
8
RD6-A 34
9
RD6-B 35
10
GNDISO 36
11
TD8-A 37
12
TD8-B 38
13
GNDISO 39
14
RD8-A 40
RD8-B 41
GNDISO 42
24S0058,3.3m
アオ/アカ1 BLU/RED1
P
アオ/クロ1 BLU/BLK1
モモ/アカ1 PNK/RED1
P
モモ/クロ1 PNK/BLK1
ミドリ/アカ1 GRN/RED1
P
ミドリ/クロ1 GRN/BLK1
ダイ/アカ1 ORG/RED1
P
ダイ/クロ1 ORG/BLK1
ハイ/アカ1 GRY/RED1
P
ハイ/クロ1 GRY/BLK1
アオ/アカ2 BLU/RED2
P
アオ/クロ2 BLU/BLK2
P
P
P
P
P
P
モモ/アカ2
モモ/クロ2
ミドリ/アカ2
ミドリ/クロ2
ダイ/アカ2
ダイ/クロ2
ハイ/アカ2
ハイ/クロ2
PNK/RED2
PNK/BLK2
GRN/RED2
GRN/BLK2
ORG/RED2
ORG/BLK2
GRY/RED2
GRY/BLK2
アオ/アカ3
アオ/クロ3
モモ/アカ3
モモ/クロ3
BLU/RED3
BLU/BLK3
PNK/RED3
BLU/BLK3
ミドリ/アカ3
ミドリ/クロ3
ダイ/アカ3
ダイ/クロ3
ハイ/アカ3
ハイ/クロ3
アオ/アカ4
アオ/クロ4
モモ/アカ4
モモ/クロ4
ミドリ/アカ4
ミドリ/クロ4
GRN/RED3
GRN/BLK3
ORG/RED3
ORG/BLK3
GRY/RED3
GRY/BLK3
BLU/RED4
BLU/BLK4
PNK/RED4
PNK/BLK4
GRN/RED4
GRN/BLK4
M-P-3
*7
MJ-A3SPF0015,3.5m,φ6
(02S4100-0)
AC IN
13
14
15
16
17
18
19
20
SNSR1
VHF-ANT
8D-FB-CV,30/50m(L>20m) *2
RG-10/UY,MAX.20m *1
*2
8D-FB-CV,30/50m(L>20m)
RG-10/UY,MAX.20m *1
BEACON TD5-A
TD5-B
RD5-A
RD5-B
LR OR ECDIS/RADAR TD4-A
TD4-B
IEC61162-1/2
RD4-A
RD4-B
SNSR3
IEC61162-1/2
IEC61162-1/2
RG-10/UY *1
N-P-8DFB
GSC-001
1
2
3
4
5
6
7
8
9
10
11
12
SNSR2
VHFアンテナ
VHF ANTENNA
150M-W2VN
*2
OR
FAB-151D
XM2A-3710
J1
TD3-A
TD3-B
RD3-A
RD3-B
TD2-A
TD2-B
RD2-A
RD2-B
TD1-A
TD1-B
RD1-A
RD1-B
IEC61162-1/2
TNC-J-3
N-P-8DFB
A
4
*1
NOTE:
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: POSITION DATA (L/L) IS REQUIRED BY EXTERNAL GPS RECEIVER.
*4: SPEED LOG IS NOT REQUIRED WHEN SOG (SPEED OVER GROUND) AND
COG (COURSE OVER GROUND) DATA ARE FED BY EXTERNAL GPS RECEIVER.
*5: ROT (RATE OF TURN) INDICATOR CAN BE CONNECTED IF PROVIDED.
*6: GYRO CONVERTOR AD-100 IS REQUIRED WHEN GYRO SIGNAL (IEC61162)
IS NOT AVAILABLE.
*7: MAX. CABLE LENGTH IS 0.5m FOR 12 VDC SPECIFICATIONS.
*8: SUPPLIED BY AMP INC.
24P0025
P
P
P
P
P
P
D-SUB 9P
D-SUB 9P
P
TD(232C)
RD(232C)
AOL
AOH
AOC
1PPSIN
24P0031
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P (MAX.30m)
LAN CABLE *1
CATEGORY 4 OR ABOVE
(MAX.30m)
1
2
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P (MAX.30m)
EXTERNAL
GPS
*3
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P (MAX.30m)
GYRO OR
THD [IMO Res. MSC.116(73)]
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P (MAX.30m)
ROT OR LOG
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P (MAX.30m)
DGPS受信機
DGPS BEACON RECEIVER
3,4
1
2
3,4
1
2
*5
*4
3,4
43
44
45
46
47
48
P
TTYCS-4,φ16 *1
(MAX.30m)
LONG RANGE COMMUNICATION OR
RADAR/ECDIS
TTYCS-4,φ16 *1
(MAX.30m)
EXTRA I/O (IEC61162-1/2)
P
P
P
TTYCS-4,φ16 *1 (MAX.30m)
P
P
TTYCS-1Q,φ13.5 *1
(MAX.15m)
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P
パイロットプラグユニット
PILOT PLUG UNIT
OP24-3 *2
206486-1
TX A
TX B
RX A
RX B
SHIELD
1
2
3
4
5
*1 *8
206485
1
4
5
6
9
PC I/O (RS-232C)
ALARM
EXTERNAL EQUIPMENT
(IEC61162-1)
LAN
P
D-SUB 9P
TTYCS-1Q,φ13.5 *1
OR CO-0.2x2P
*6
AD-100
GYRO
NOT USED
IEC61162-1: 4800BPS
IEC61162-2: 38.4KBPS
IEC61162-4: 10BASE-T
NOT USED
DRAWN
Apr. 16 '04
CHECKED
APPROVED
SCALE
K.MIYAZAWA
TAKAHASHI.T
DWG. No.
TYPE
FA-100
名前
国際船舶自動識別装置
相互結線図
Y. Hatai
MASS
NAME
kg
CO-0.2x2P: CO-SPEVV-SB-C 0.2x2P,φ10.5
S-1
6
C4417-C02- K
U-AIS TRANSPONDER
INTERCONNECTION DIAGRAM
PC
Download PDF

advertising