Installation manual | Furuno FAR-2157-BB Marine RADAR User Manual

MARINE RADAR
FAR-2157/2157-BB/2157-D
Installation manual
SAFETY INSTRUCTIONS....................... i
3.3 Adjustment Sweep Timing .................... 3-5
3.4 Suppressing Main Bang ....................... 3-6
SYSTEM CONFIGURATION ................. iii
EQUIPMENT LISTS .............................. iv
3.5 Other Settings ...................................... 3-7
4. OPTIONAL EQUIPMENT ................4-1
1. MOUNTING ..................................... 1-1
4.1 Gyro Converter GC-10 ......................... 4-1
1.1 Antenna Unit ........................................ 1-1
4.2 Memory Card Interface Unit ............... 4-10
1.2 Monitor Unit.......................................... 1-7
4.3 DVI-RGB Conversion Kit .................... 4-13
1.3 Control Unit ........................................ 1-10
4.4 BNC Connector Converter ................. 4-16
1.4 Processor Unit .................................. 1-15
5. IO DATA...........................................5-1
1.5 Power Supply Unit ............................ 1-16
PACKING LISTS ................................ A-1
2. WIRING ........................................... 2-1
2.1 Wiring Overview................................... 2-1
2.2 Antenna Unit ........................................ 2-2
OTLINE DRAWINGS .......................... D-1
INTERCONNECTION DIAGRAM ....... S-1
2.3 Monitor Unit (for FAR-2157)................. 2-8
2.4 Processor Unit ..................................... 2-9
2.5 Power Supply Unit ............................. 2-14
2.6 Changing AC Power Specification ..... 2-16
3. ADJUSTMENT ................................ 3-1
3.1 Initializing tuning .................................. 3-1
3.2 Heading Alignment............................... 3-3
www.furuno.co.jp
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone : +81-(0)798-65-2111
Fax
: +81-(0)798-65-4200
All rights reserved.
Printed in Japan
A : FEB . 2007
E : FEB . 10, 2011
Pub. No. IME-35220-E
(HIMA )
FAR-2157/BB
*00014869214*
*00014869214*
* 0 0 0 1 4 8 6 9 2 1 4 *
SAFETY INSTRUCTIONS
The installer must read and follow all the safety instructions before attempting to install the
equipment.
WARNING
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Warning, Caution
Prohibitive Action
Mandatory Action
WARNING
Radio Frequency Radiation Hazard
The radar antenna emits electromagnetic radio frequency (RF) energy which can
be harmful, particularly to your eyes. Never look directly into the antenna aperture
from a close distance while the radar is in operation or expose yourself to the
transmitting antenna at a close distance.
Distances at which RF radiation levels of 100 W/m2 and 10 W/m2 exist are given in
the table below.
Note: If the antenna unit is installed at a close distance in front of the wheel house,
it may be necessary to halt transmission within a certain sector of antenna
revolution. This can be done from the SCANNER menu.
Radiator
type
Distance to Distance to
100 W/m2
10 W/m2
point
point
XN4A
1.20 m
13.60 m
XN5A
1.10 m
12.30 m
i
WARNING
CAUTION
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
A proper license is necessary to install
a radar.
See your dealer for details.
Only qualified personnel should work
inside the equipment.
Wear a hard hat and safety belt when
mounting the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna mast.
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna
mast.
Do not install units other than the
antenna unit in a place subject to rain
or water splash.
Fire, electrical shock or injury can result if
water leaks into those units.
Turn off the power at the switchboard
before beginning the installation.
Fire, electrical shock or injury can result if
the power is on during the installation.
Use only the specified power cables.
Use of power cables that are thinner than
those specified can cause fire.
Securely attach protective earth to the
ship's body.
The protective earth is required to prevent
electrical shock.
ii
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Standard Steering
compass compass
Antenna Unit
(60 kw)
4.30 m
2.80 m
Monitor Unit
(MU-201CR)
1.55 m
1.00 m
Processor Unit
(RPU-013)
1.35 m
0.85 m
0.30 m
0.30 m
0.95 m
0.60 m
0.65 m
0.45 m
Power Supply
Unit (PSU-006)
0.30 m
0.30 m
Memory Card
Interface Unit
(CU-200)
0.90 m
0.60 m
Switching Hub
(HUB-100)
1.00 m
0.60 m
Monitor Unit
(MU-190)
1.65 m
Control Unit
(RCU-014)
Control Unit
(RCU-015)
Control Unit
(RCU-016)
1.05 m
SYSTEM CONFIGURATION
ANTENNA UNIT
XN4A-RSB-106
XN4A-RSB-107
XN5A-RSB-106
XN5A-RSB-107
POWER SUPPLY UNIT
PSU-006
(For antenna motor)
24 VDC
RECTIFIER
RU-3423
100/110/115/220/230 VAC
1f, 50/60 Hz
200 VAC, 3f, 50 Hz
220 VAC, 3f, 60 Hz
110 VAC, 3f, 60 Hz
TRANSFORMER
RU-5693
220 VAC, 3f, 50 Hz
TRANSFORMER
RU-6522
MONITOR UNIT
MU-201CR
(For FAR-2157)
MU-190
(For FAR-2157-D)
CONTROL UNIT
RCU-014
(Standard)
OR
RCU-015
(Trackball)
TRANSFORMER
RU-5466-1
440 VAC, 3f, 50 Hz
(For HV power)
100-115V/220-230 VAC
1f, 50/60 Hz
TRANSFORMER
440 VAC, 1f,
RU-1803
50/60 Hz
Navigator
Speed Log
IEC-61162 Serial data
(I/O)
IEC-61162 Serial data
(Input)
PROCESSOR
UNIT
RPU-013
GYRO CONVERTER
GC-10
Gyrocompass
*
100-230 VAC
1f, 50/60 Hz
CONTROL UNIT
RCU-016
Radar Remote
Display
SWITCHING HUB
HUB-100
Alarm
AD-100
AIS
VDR
Track Controller
External
Monitor
MEMORY CARD
INTERFACE UNIT
CU-200-FAR
TRANSFORMER
RU-1803
: Standard supply
: Optional supply
: Local supply
100-115 VAC/
220-230 VAC
1f, 50/60 Hz
440 VAC
1f, 50/60 Hz
Equipment category
* FAR-2157-BB is not equipped with a
monitor unit. Procure one locally.
Unit
Category
Antenna
Exposed to weather
Other units
Protected from weather
iii
EQUIPMENT LISTS
Standard supply
Name
Antenna Unit
Type
Code No.
XN4A-RSB-106
–
XN4A-RSB-107
–
XN5A-RSB-106
–
XN5A-RSB-107
–
Qty
200/220 VAC, 2570 mm
1
–
1
Monitor Unit
MU-201CR
–
1
MU-190
–
Processor Unit
RPU-013
–
Control Unit
RCU-014
–
RCU-015
–
Accessories*
Spare Parts*
24 VDC, 2570 mm
200/220 VAC, 3210 mm
24 VDC, 3210 mm
Power Supply Unit PSU-006
Installation
Materials*
Remarks
For FAR-2157
For FAR-2157-D
1
1
1
Standard type
Trackball type
CP03-31301
008-572-970
For antenna unit
CP03-25700
000-080-435
CP03-25710
000-080-436
CP03-25730
000-082-191
CP03-25720
000-080-437
CP03-25800
000-080-434
1
Cable assy. for monitor unit
CP03-25602
008-535-940
1
For processor unit
CP03-31401
008-572-750
1
For power supply unit
CP03-25604
008-539-850
1
For control unit
FP03-09810
008-536-010
1
For monitor unit
FP03-09850
008-535-610
FP03-09860
008-535-690
SP03-14404
008-535-910
SP03-14405
008-535-920
SP03-09203
008-424-380
1
For 24 VDC antenna unit
SP03-14401
008-535-990
1
For FAR-2157's monitor unit
SP03-15501
008-572-730
SP03-15501
008-572-740
15 m signal cable (RW-9600)
1
30 m signal cable (RW-9600)
40 m signal cable (RW-9600)
50 m signal cable (RW-9600)
1
1
1
For standard-type control unit
For trackball-type control unit
For processor unit, 100 VAC
For processor unit, 220 VAC
For power supply unit, 100 VAC
For power supply unit, 220 VAC
* See packing list at end of this manual.
Optional equipment
Name
Type
Gyro Converter GC-10-2
Rectifier Unit
RU-3423
iv
Code No.
000-080-440
–
Remarks
See Chapter 4.
100/110/115/220/230 VAC to 24 DC,
for power supply unit
(Continued on the next page.)
Name
Stepdown
Transformer
Unit
Type
Code No.
Remarks
RU-1803
–
440 to 100 VAC, for processor unit
RU-5693
RU-6522
–
–
110 to 220 VAC, 3φ, for antenna unit
220 to 200 VAC, 3φ, for antenna unit
RU-5466-1
–
440 to 200 VAC, 3φ, for antenna unit
Memory Card
Interface Unit
CU-200-FAR
000-081-568
External Alarm
Buzzer
Control Unit
OP03-21
000-030-097
RCU-016
000-080-299
Remote type, w/FP03-09860
RAM Card
O0RAM08MC-005
004-376-740
8MB
DVI-RGB
Converter Kit
OP03-180-1
008-545-590
For installation in the field.
OP03-180-2
008-536-070
For installation in field. See Ch. 4.
Cable Assy.
XH10P-W-6P L=20M
000-149-748
Processor unitQControl unit, 20 m
XH10P-W-6P L=30M
000-149-749
Processor unitQControl unit, 30 m
XH10P-W-5P-A L=10M
000-149-050
Between control units, 10 m
XH10P-W-5P-A L=20M
000-149-051
Between control units, 20 m
XH10P-W-5P-A L=30M
DVI-D/D S-LINK 10M
000-149-052
000-150-200
Between control units, 30 m
Processor unitQControl unit, 10 m
S03-9-5(8-8P)
008-206-640
External radar, 5 m, 8-8P
S03-9-10(8-8P)
008-206-650
External radar, 10 m, 8-8P
S03-9-15(8-8P)
008-209-160
External radar, 15 m, 8-8P
CP03-28900
000-082-658
FR-FTPC-CY 10 m, modular
connector MPS588-C, 2 pcs.
CP03-28910
000-082-659
FR-FTPC-CY 20 m, modular
connector MPS588-C, 2 pcs.
CP03-28920
000-082-660
Bracket Assy.
FP03-09820
008-535-560
FR-FTPC-CY 30 m, modular
connector MPS588-C, 2 pcs.
Hanger assy. for monitor unit
Handgrip Assy.
FP03-09840
008-535-570
For monitor unit
Dust Cover
03-163-1201
100-307-260
For monitor unit
Clamp Assy.
OP03-182
008-535-620
For RCU-014
008-535-630
For control unit
Connection
Stand
OP03-198
OP03-183
001-008-050
008-535-640
RCU-014QMU-201CR
OP03-185
008-535-660
RCU-014
Hanger Kit
FP03-10201
008-539-530
Desktop inst. kit for CU-200-FAR
BNC
Connector
Converter
DSUB-BNC-1
000-148-528
For connecting VDR
Switching Hub
HUB-100
Hood
FP03-11500
001-020-090
For MU-201CR display unit
Slim Hood
FP03-11510
001-034-390
For MU-201CR display unit
Installation
Materials
(Armored LANCable Kit)
Flush Mount Kit FP03-09870
–
w/CP03-27430, see Chapter 4.
See Operator's Manual for HUB-100,
issued separately.
v
This page is intentionally left blank.
vi
1. MOUNTING
NOTICE
Do not apply paint, anti-corrosive sealant
or contact spray to coating or plastic
parts of the equipment.
Those items contain organic solvents that
can damage coating and plastic parts,
especially plastic connectors.
1.1 Antenna Unit
Mounting considerations
The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on
a suitable platform. The mounting location should afford a good all-round view and satisfy the
siting and mounting considerations mentioned below.
Siting
• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow
direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar
picture.
• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial performance and hot gases may deform the radiator. The antenna unit must not be mounted where
the temperature is more than 70°C.
• Locate a direction finder antenna clear of the antenna unit to prevent interference to the direction finder. A separation of more than two meters is recommended.
• Choose a location where reflections from the radar reflector will not be received by the radar
antenna.
• The "standard" antenna unit orientation has the cable glands directed toward the bow.
• Leave sufficient space around the unit for maintenance and servicing. See the antenna unit outline drawing for recommended maintenance space.
Mounting
• Use rope and crane to hoist the antenna unit to the mounting location. Lifting fixtures are provided on the antenna chassis to which to fasten rope.
• Mount the unit parallel to the waterline.
• A hole is required in the mounting platform for the antenna cable.
• An appropriate platform should be constructed at the mounting location to facilitate installation
and maintenance work.
• Connect ground wire between antenna terminal on antenna chassis and ground point.
• If the mounting platform is made of steel paint it to prevent electrolytic corrosion. DO NOT paint
the antenna radiator.
1-1
Assembling the antenna unit
The antenna unit should be assembled before mounting it. Follow the procedure below to
assemble the antenna unit. The numbers in parentheses refer to the parts numbers shown in the
illustration on the next page.
1. Grease the O-ring(1) and set it to the O-ring groove in the flange on the rotation coupler on the
antenna base. Fasten the feeder waveguide to the antenna base with hex bolts B(2). Coat the
surface of the waveguide flange with silicon rubber, referring to the illustration below for instructions.
2. Loosely fasten the antenna radiator to the antenna base with hex bolts(3) and(6), flat
washers(5) and (7), spring washers(4) and (8) and hex nut(9).
3. Grease the O-ring(1) for the antenna radiator and set it to the O-ring groove on the feeder
waveguide flange on the antenna radiator. Fasten the feeder waveguide to the antenna radiator
with hex head bolts(2).
4. Fasten the waveguide clamp(13) to the waveguide clamp insulator(14) with hex head bolt(10),
flat washer(12) and spring washer(11).
5. Securely fasten the antenna radiator to the antenna base.
How to coat waveguide flange with silicon rubber
(1) Do not let sealant contact O-ring groove.
(2) Evenly coat flange with silicon rubber at the locations shown
below.
Use enough silicon rubber so that it oozes out when
fastening bolts. Wipe off surplus. Be sure silicon rubber
does not contact choke guide or feeder waveguide.
Silicon
O-ring rubber
Choke guide
O-ring
Silicon rubber
Note: The surface to be coated with silicon rubber should be
cleaned beforehand to remove foreign material or silicon
rubber previously applied.
How to coat waveguide flange with silicon rubber
1-2
Antenna Radiator
Rotation Coupler
Antenna Base
Feeder Waveguide
Parts of antenna unit XN4A/XN5A
List of parts for assembling antenna unit
No.
Name
Type
Qty
1
O-ring
AS568-125
2
2
Hex Bolt B
M4×16 (SUS304)
8
3
Hex Bolt
Antenna unit XN4A: M8×25 (SUS304)
Antenna unit XN5A: M8×35 (SUS304)
4
4
Spring Washer
M8 (SUS304)
4
5
Flat Washer
M8 (SUS304)
4
6
Hex Bolt
M8×30 (SUS304)
4
7
Flat Washer
M8 (SUS304)
8
8
Spring Washer
M8 (SUS304)
4
9
Hex Nut
M8 (SUS304)
4
10
Hex Bolt
M4×30 (SUS304)
2
11
Spring Washer
M4 (SUS304)
2
12
Flat Washer
M4 (SUS304)
2
13
Waveguide Clamp
RSB-2006-2
1
14
Waveguide Clamp Insulator
03-003-4003-0
1
Chemiseal
S-8400W, aluminum tube, 50g
1
1-3
How to hoist antenna unit
1. Referring to the illustration below, fasten rope A of approx. 85 cm in length and fasten rope B
of approx. 100 cm in length.
2. Place protective material (cardboard, foam, etc.) between rope and radiator at the asteriskmarked locations shown below, to prevent damage to the radiator.
3. Hoist the antenna slightly and confirm that the load applied to the radiator is not excessive. (If
load is excessive, lower the antenna unit and adjust lengths of ropes.)
4. Hoist the antenna unit to the mounting location.
A
How to attach hoisting ropes to antenna unit
1-4
B
Fastening antenna unit to the mounting platform
WARNING
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
Only qualified personnel should
work inside the equipment.
Wear a hard hat and safety belt when
mounting the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna mast.
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna
mast.
Note: The antenna unit is made of cast aluminum, which is subject to electrolytic corrosion if the
mounting platform is steel or iron. To prevent electrolytic corrosion, use the supplied seal washers
and corrosion-proof rubber mat.
Fix the antenna unit to the mounting location, referring to the procedure below and the illustration
on the next page.
1. Referring to the antenna unit outline drawing, prepare a mounting platform at the mounting
location for the antenna unit.
2. Lay the corrosion-proof rubber mat (supplied) on the mounting platform, aligning the holes on
the rubber mat with the fixing holes on the mounting platform.
3. Lay the antenna unit on the rubber mat, orienting it so the cable gland is directed toward ship's
bow.
4. Use hex bolts (M12×60), nuts, flat washers and seal washers to fix the antenna unit to the
mounting platform.
5. Arrange the ground point at a location on the mounting platform that is within 300 mm from the
ground terminal on the antenna unit. Fasten the ground wire (RW-4747, 340 mm) there, using
the M6×25 hex bolt, nut and washers.
6. Connect the other end of the ground wire to the ground terminal on the antenna unit.
7. Coat the ground terminal, ground point on the mounting platform and fixing bolts on the
antenna unit with anticorrosive sealant (supplied).
1-5
Seal washer
Coat with
anticorrosive sealant.
Corrosionproof rubber
mat
Lay rubber mat, fix
antenna with bolts, nuts
and seal washers.
Coat with anticorrosive
sealant.
Ground wire
Ground terminal is provided
on antenna unit.
Hex bolt
Ground
wire
Spring washer
Flat washer
Spring washer
Hex nut
Anticorrosive
sealant
Ground
wire
How to mount the antenna unit
1-6
Hex nut
Spring washer
Flat washer
Hex bolt
1.2 Monitor Unit
The monitor unit is can flush mounted in a panel or mounted on a desktop (requires optional
accessories).
The FAR-2157-BB is not equipped with a monitor unit. Procure a suitable monitor unit locally. Recommended monitor: SXGA (1280×1024), aspect ratio 5:4.
For MU-190, see the applicable Operator’s Manual.
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Select a location where the screen can be viewed conveniently while facing the bow.
• Locate the unit out of direct sunlight and away from heat sources because of heat that can build
up inside the cabinet.
• Locate the unit away from places subject to water splash and rain.
• Leave sufficient space on the sides and rear of the unit to facilitate maintenance, referring to the
outline drawing for maintenance space.
• The monitor unit will give interference to a magnetic compass if it is placed too close to the compass. Observe the compass safe distances on page ii to prevent interference to the compass.
Mounting procedure
Flush mounting
Follow the procedure below to mount the monitor unit in a console.
1. Make a cutout in the mounting location referring to the outline drawing shown below.
2. Set the monitor unit to the hole and fix it with four self-tapping screws (6×30).
3. Attach panel hooks near the fixing holes (upper part). See next page. These are used to pull
out the monitor unit from the panel for servicing.
4. Attach four panel covers to the fixing holes.
1
4-FIXING HOLES
(79)
296 1
454
296 1
420
506
490
506 1
534
4-φ8
FIXING HOLES
30
80
Mounting dimensions for flush mounting the monitor unit
1-7
Panel hook
Panel cover
Fixing screw
How to attach panel hook and panel cover
Note: If you need to remove the monitor unit from the console, remove the four panel covers with
your fingernail and use two panel hooks supplied as accessories to lift the monitor unit.
Desktop mounting
Use the optional desktop mouting kit (Type: FP03-09820, Code No.: 008-535-560) to mount the
monitor unit on a desktop.
Contents of desktop mounting kit FP03-09820
Name
Type
Code No.
Qty
Hanger L
03-163-1111
100-305-141
1
Hanger R
03-163-1112
100-305-181
1
Hanger stay
03-163-1113
100-305-191
1
Hole plug
CP-30-HP-13
000-160-074-10
2
Snap button
KB-13, Black
000-570-276-10
4
Hex. bolt
M6×25
000-162-949-10
4
Hex. bolt
M10×30
000-162-884-10
2
Spring washer
M10
000-864-261
2
Flat washer
M10
000-864-131
2
1. Assemble two hangers and hanger stay with two hex bolts (M10×30), flat washers and spring
washers and cover each hex bolt with hole plug.
2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard supply).
3. Fasten the monitor unit to the mounting hanger assembly with four hex bolts (M6×25, supplied).
4. Cover each hex bolt with a panel cover (4 pcs.).
5. Cover fixing holes for hand grips with snap buttons (4 pcs).
1-8
Hanger (L)
M12 bolts for fixing
(Dockyard supply)
Hanger stay
Hanger (R)
Panel cover
Snap button
Flat Washer M10
Spring Washer M10
Hex bolt
(M6x25)
Hex bolt
M10x30
Hole plug
Panel cover
To remove this, insert fingernail in groove.
Fastening monitor unit to hanger
Attaching hand grips
Hand grips are optionally available for the desktop-mount monitor unit. Attach them as follows:
1. Remove the snap buttons attached at step 5 on the previous page.
2. Fix hand grips with wave washers, rosette washers and flat head screws.
Wave washer
Rosette washer
Flat head screw (torque: 7.6 Nm)
Hand grip
How to attach hand grips
Attaching hood
When it is too bright in the daytime, use the optional hood (Type: FP03-11500, Code No.: 001020-090) to shade the screen.
Contents of hood
Name
Type
Hood
FP03-11501
Fixing plate
03-163-2202-0
Screw
M4x10 D=13 US304
Code No.
Qty.
001-020-120
1
100-335-560-10
4
000-862-543
4
1-9
1. Desktop mounting: Fasten the fixing plates to the fixing holes with the hex head bolts (supplied).
Flush mounting: Fasten the display unit to the mounting location, and then attach the fixing
plates with four self-tapping screws.
Hex head bolt
Fixing plate
Fixing hole
2. Attach the hood to the display unit (the hood is outside of the fixing plates).
3. Fasten the hood to the fixing plates with four screws supplied (M4x10).
1.3 Control Unit
Mounting considerations
The control unit may be mounted on a desktop, with or without the KB fixing metal (supplied) which
mounts the control unit at an angle. When selecting a mounting location, keep in mind the following points:
• Select a location where the control unit can be operated conveniently while observing the display screen.
• Locate the unit away from heat sources because of heat that can build up inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Determine the mounting location considering the length of the signal cable between the control
unit and the processor unit. (A 10 m signal cable is attached to the control unit.)
• A magnetic compass will be affected if the control unit is placed too close to it. Observe the compass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Fixing with KB (keyboard) fixing plate
The KB fixing plate sits the control unit at a comfortable angle, like the retractable legs on a PC
keyboard.
1. Fix the KB fixing plate to the bottom of the control unit.
2. Attach cushions (three for RCU-014, two for RCU-015/RCU-016) to the bottom of the control
unit as shown below.
3. Fix the unit to a desired location with self-tapping screws (local supply).
KB fixing plate
Cushion
Control unit RCU-014/015/016, side view
1-10
Fixing without KB fixing plate
1. Drill four mounting holes of 5 mm diameter, referring to the outline drawing at the back of this
manual.
2. Fix the control unit with four screws (M4) from the under side of the desktop. (M4 screws with
a sufficient length for the thickness of the desktop should be provided locally.)
# Minimum recommended service space
180
136±1
#70
4-M4 (Fixing holes)
(bottom)
308±1
398
Mounting dimensions for control unit RCU-014
24
32
F3
180
136±1
F1
F2
F4
110±1
160
4-M4 (Fixing holes)
(REAR)
Mounting dimensions for control unit RCU-015/RCU-016
1-11
Flush mounting
Use the optional flush mount kit FP03-09870 (Code No. 008-535-630) to flush mount the control
unit RCU-014, RCU-015 and/or RCU016 in a console.
Contents of flush mount kit for RCU-014/015/016
Name
Type
Qty
Mounting plate
03-163-7531
4
Hex bolt
M5
4
Wing screw
M5×40
4
Pan head screw
M4×12
4
1. Prepare a cutout in the mounting location as shown in the figure below.
170±2
176±2
388 ±2
150±2
Flush mount cutout for RCU-014
Flush mount cutout for RCU-015 and RCU-016
2. Set the control unit to the cutout.
3. From the rear side, attach the mounting plate to the control unit with four screws.
4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing screw.
53
(P)
#70
92
53
#70
86
(P)
5. Fasten each wing screw and then fasten the hex nuts as shown in the figure below.
171
Note:
# Minimum recommended service space
P <
=10
To change location of
cable entrance, see
page 1-14.
Flush mount mounting dimensions for control unit RCU-014 (left) and RCU-015/RCU-016
1-12
Connecting RCU-016 in series with RCU-014
1. Pass the cable from RCU-016.
2. Plug in connector
to J502.
3. Clamp the copper part of the cable with the cable clamp.
Control unit RCU-014, inside view
1-13
Changing the cable entrance on control unit RCU-015/RCU-016
To change the cable entrance from the side (default) to the bottom, modify the unit as shown
below.
Screw M3X8
(torque: 10.78 Nm)
Bottom of unit
2. Pull out cable.
3. Pass cable thru this hole.
Cable clamp
03-163-7804
Screw M4X8
(torque: 1.47 Nm)
4. In here, clamp copper part
of cable with cable clamp
removed at step 1.
1. Remove cable
clamp.
J522: Plug in here to connect RCU-016 in series with RCU-015.
Changing cable entrance on control unit RCU-015/RCU-016
1-14
1.4 Processor Unit
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Locate the processor unit away from heat sources because of heat that can build up inside the
cabinet.
• Locate the unit away from places subject to water splash and rain.
• Leave sufficient space at the sides and rear of the unit to facilitate maintenance, referring to the
outline drawing.
• A magnetic compass will be affected if the processor unit is placed too close to it. Observe the
compass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Fix the unit with four M6 bolts or self-tapping screws.
#50
2-φ7 FIXING HOLES
25
385
# Minimum recommended
service space
380
410
340±1
370±1
R3
.5
350±1
7
2-FIXING NOTCH
Mounting dimensions for processor unit
Upper case assy.
Note: If you fix the unit with the
cable entry up, do not unfasten
the screw (M3x10) that fastens
the upper case assy. and lower
case assy. of the processor unit.
Lower case assy.
Do not unfasten
this screw.
1-15
1.5 Power Supply Unit
Mounting considerations
The power supply unit may be mounted on a bulkhead or a deck. Because it has no operation
requirements it can be located almost anywhere, provided the location is well ventilated.
Mounting procedure
Fix the unit to the mounting location with four 6×20 self-tapping screws (local supply). For
mounting on a bulkhead, do the following:
1. Mark location for mounting holes.
2. Screw in the self-tapping screws at the location for the bottom fixing holes, leaving a gap of
about 5 mm between the bottom of the screw head and bulkhead.
3. Set the unit to the screws inserted at step 1.
4. Fasten the self-tapping screws at the top of the unit.
5. Tighten all self-tapping screws.
FIXING
HOLE
WINDOW
LED
440
9
2-φ7
420±1
#50
240±1
TERMINAL
TERMINAL
#: MAINTENANCE SPACE
240±1
Mounting dimensions for power supply unit
1-16
GND
TERMINAL
(11)
.5
R3
7
2. WIRING
2.1 Wiring Overview
POWER
SUPPLY
UNIT
TPYCY-2.5
TPYCY-1.5
ANTENNA UNIT
TB801
TB802
MONITOR UNIT
24 VDC
TPYC-2.5
RW-9600
15/30/40/50 m
(Max.100 m)
RU-5693
TPYC-1.5
110 VAC, 3φ,
60 Hz
220 VAC, 3φ,
50 Hz
440 VAC, 3φ,
50 Hz
RU-3423
RU-6522
RU-5466-1
100-115 VAC/220-230V,
1φ, 50/60 Hz
440 VAC,
1φ, 50/60 Hz
RU-1803
DPYC-2.5
100/110/115/
220/230 VAC
1φ, 50/60 Hz
DVI-D/D SINGLELINK 5/10m
200 VAC, 3φ, 50 Hz
220 VAC, 3φ, 60 Hz
PROCESSOR UNIT
DPYC-2.5
CONTROL UNIT
(RCU-014 or RCU-015)
MEMORY CARD
INTERFACE
CU-200-FAR
XH10P-W-5P
L=10/20/30 m
100-230 VAC
1φ, 50/60 Hz
XH10P-W-6P L=1.5/10/20/30m
CONTROL UNIT
(RCU-016)
DPYC-2.5
: Fabrication required
100-115V/220-230 VAC
1φ, 50/60Hz
F1
F2
F3
F4
2-1
2.2 Antenna Unit
Gland for HV cable
(TPYCY-1.5)
Antenna safety switch
PCB 03P9435
PCB 03P9436
Terminal strip
Cover
Cover
Gland for power cable (TPYCY-2.5)
Ground terminal
Gland for signal cable (RW-9600)
Antenna unit, front view
Fabricating signal cable RW-9600
1. Use a ratchet or box wrench (diagonal 13 mm) to open port- and starboard-side covers on the
antenna unit.
2. Unfasten the gland nut for the signal cable and remove the gasket, flat washers (3 pcs.) and
gland cap. (The gland cap may be discarded.)
3. Fabricate the signal cable as follows:
a) Remove the vinyl sheath, armor and sheath by the amounts shown in the figure below.
b) Unravel the shield to expose cores.
c) Shorten cores (except coax) considering their locations on the terminal inside the antenna unit.
d) Shorten the shield, leaving 300 mm. Attach crimp-on-lug (FV5.5-4, yellow, φ4) to shield.
e) Remove the sheath of cores by 6 mm.
f) Unravel armor.
g) Fix vinyl wire, coaxial cable and shield by taping the shield with vinyl tape at the location shown
below.
Vinyl
sheath
Sheath
Armor
20 mm
Shield
550 mm
5 mm
500 mm
Shield
Taping
Coaxial cable
Vinyl wire
6
14 5 9
Unravel armor.
Core
Fold back shield.
Shield
Crimp-on lug
Coaxial cable
Fabricating signal cable RW-9600
2-2
4. In the order shown in the figure below, pass the gland nut, flat washers (3 pcs.) and gasket onto
the signal cable.
Armor
Gasket
Flat washer
(2)
Signal cable
Flat washer Gland nut
(1)
5. As shown in the figure below, fold back the armor onto flat washer (2) and insert remaining
armor through flat washer (3). Cut off the part of the armor that protrudes past the flat washers
(2) and (3).
Fold back armor
Flat washer (2)
Flat washer
(3)(2) (1)
Cut off armor that protrudes
past flat washer.
6. Lead the signal cable through its cable gland and then into the chassis. Coat the threaded part
of gland nut with sealant (supplied) and then tighten the nut.
TB801
PCB 03P9436
Cable gland for
signal cable (RW-9600)
Antenna unit, front view
2-3
7. Using the terminal opener provided, connect cores (except coaxial cable) to their appropriate
locations on TB801 on the PCB 03P9436. Refer to the interconnection diagram for wiring
details.
Push down.
Terminal
opener
Wire
Twist.
WAGO connector
Procedure
1. Twist core.
2. Insert terminal opener as shown and push down.
3. Insert core into hole.
4. Release terminal opener.
5. Tug on wire to confirm that it is firmly in place.
How to wire WAGO connector
TB802 on
PCB 03P9435
Cable gland for
HV cable (TPYCY-1.5)
Terminal TB901
Cable gland for
power cable (TPYCY-2.5)
Fix coax cable with
with this clamp.
Fasten shield of signal cable here.
Antenna unit, front view
2-4
8. Connect coaxial cable to TB802 on the PCB 03P9435. Fix the shield and conductor as shown
below.
Fasten shield by clamp.
NOTICE
Taping
Fasten conductor
with screw.
Fasten BARE conductor. Do not
use a crimp-on lug, to prevent
increased contact resistance.
How to fasten coaxial conductor
9. Referring to the illustration above for location, fasten shield (crimp-on lug FV5.5-4 attached) of
signal cable with screw on chassis.
10.Pocess unused wires as follows:
a) Slip shrink tubing onto cores and heat.
b) Bind the wires with a cable tie and pass them through the cable gland on the chassis.
11.Close the cover which protects pcb 03P9436.
12.Seal the cable gland for the signal cable with putty.
2-5
Fabricating HV cable TYPCY-1.5 and power cable TYPCY-2.5
1. Unfasten the gland nut for the HV cable and remove gasket, flat washers (3 pcs.) and gland
cap. (The gland cap may be discarded.)
2. Fabricate the HV cable as shown below.
20 mm
600 mm
Vinyl
sheath
Armor
5 mm
Sheath
Sheath
FV2-4
Conductor
S = 1.50 mm2
φ = 1.56 mm
Armor
SECTIONAL VIEW
How to fabricate HV cable TYPCY-1.5
3. In the order shown in the figure below, pass the gland nut, flat washers (3 pcs.) and gasket onto
the HV cable.
4. As shown in the figure below, fold back the armor onto flat washer (2) and insert remaining
armor through flat washer (3). Cut off the part of the armor that protrudes past the flat washers
(2) and (3).
Flat washer
(1) (2) (3)
HV cable
Cut off armor that
protrudes past washer.
Gland nut
Gasket
Passing flat washer, etc. onto HV cable
5. Pass the HV cable through its cable gland and then tighten gland nut.
6. Connect wiring to TB901, referring to the interconnection diagram.
7. Unfasten the gland nut for the power cable and remove gasket, flat washer (3 pcs.) and gland
cap. (The gland cap may be discarded.)
2-6
8. Fabricate the power cable as shown below.
Armor
25 mm
FV2-4
500 mm
Vinyl sheath
Sheath
5 mm
Sheath
Armor
Conductor
S = 2.50 mm2
φ = 2.01 mm
SECTIONAL VIEW
How to fabricate power cable TYPCY-2.5
9. In the order shown in figure below, pass the gland nut, flat washers (3 pcs.) and gasket onto
the power cable.
10.As shown in the figure below, fold back the armor onto flat washer (2) and insert remaining
armor through flat washer (3). Cut off the part of the armor that protrudes past the flat washers
(2) and (3).
Flat washer
(1) (2) (3)
Power cable
Cut off armor that
protrudes past washer.
Gland nut
Gasket
Passing flat washer, etc. onto power cable
11.Pass the power cable through its cable gland and tighten gland nut.
12.Connect wiring to the terminal TB901, referring to the interconnection diagram.
CAUTION
High voltage is present at the No. 6 pin
of TB901. Miswiring at this pin can
damage the antenna unit.
13.Close the cover that protects pcb 03P9435.
14.Seal the cable gland for the power cable and HV cable with putty.
2-7
2.3 Monitor Unit
Two cables are terminated at the monitor unit: the signal cable from the processor unit (5 m or 10
m cable) and the power cable from the ship's mains. The signal cable comes with a connector preattached to it for connection to the monitor unit. Fabricate the power cable as below. Use cable
DPYC-2.5 (Japan Industry Standard) or the equivalent. Be sure to ground the unit, with IV-8sq
wire (local supply). For MU-190, see the applicable Oprator’s Manual.
Note: Pass the AC line through a double-contact breaker (shipyard supply). Further, for vessels
where the power line is grounded, connect one end of the line to the C (common) terminal and the
other end to the H terminal.
Fabricating the power cable DPYC-2.5
1. Remove the armor from the cable by 40 mm.
2. Remove the vinyl sheath by 35 mm.
3. Remove the insulation from the cores by about 10 mm..
4. Peel paint from the armor by 40 mm.
5. Cover the end of the armor with vinyl tape. Fix crimp-on lugs (FV2-4, blue, supplied) to the
cores.
(1)
DPYC-2.5
Armor
Approx. 40 mm
Armor
35 mm
(2)
Vinyl sheath
Conductor
S = 2.5 mm2
φ = 2.01 mm
SECTIONAL VIEW
10 mm
(3)
40 mm: Peel paint.
(4),
(5)
Crimp-on lug
Taping
Fabricating power cable DPYC-2.5
Cable entrance for signal cable
(Connect end which has no EMI core here.)
Cable entrance for power cable
Monitor unit MU-201CR, rear view
2-8
2.4 Processor Unit
Four cables are terminated at the processor unit: the antenna unit cable, monitor unit cable (FAR2157 only), control unit cable and the power cable. Cables other than the power cable come with
a connector preattached to them. Fabricate the power cable as below.
Note: Pass the AC line through a double-contact breaker (shipyard supply). Further, for vessels
where the power line is grounded, connect one end of the line to the C (common) terminal and the
other end to the H terminal.
Fabricating the power cable DPYC-2.5
1. Remove the armor from the cable by 40 mm.
2. Remove the vinyl sheath by 35 mm.
3. Remove the insulation from the cores by about 10 mm.
4. Peel paint from the armor by 40 mm.
5. Tape the end of the armor with vinyl tape. Fix crimp-on lugs (FV2-4, blue, supplied) to the cores.
(1)
DPYC-2.5
Armor
Approx. 40 mm
Armor
35 mm
(2)
Vinyl sheath
Conductor
S = 2.5 mm2
φ = 2.01 mm
SECTIONAL VIEW
10 mm
(3)
40 mm: Peel paint.
(4),
(5)
Crimp-on lug
Taping
Fabricating power cable DPYC-2.5
2-9
Connection of cables
The power cable is connected to the terminal board on the rear panel and the signal cable from
the monitor unit is connected to the DVI-D connector. Other cables are connected to the printed
circuit board 03P9342. Be sure to ground the unit, with IV-8sq wire (local supply).
Cable clamp for power cable
Monitor unit
*
Network
Terminal board for power cable
DVI-D monitor
Remove the
protective cover.
F70
FUSE
1
15
DC/AC
F1
2
Control unit**
Heading senor
Speed log
Navigator
Power cable
9 14
ACK
Cable clamp
17
21
2
3
4
5
HDG
φ9
6
18
19
1
7
AIS
AD100
8
28
GYRO
PSU004
24
φ7.4
VDR IN
24'
φ7
26
VDR OUT
Memory Card IF unit
VDR OUT
Antenna unit
GND TERMINAL
20
RSD
φ18.9
VDR IN
Power supply unit
Gyrocompass
AD-100
AIS
Processor unit, rear view
*: The connector with EMI core should be connected to the processor unit.
**: The configuration of optional cable between the processor unit and the control unit is as follows.
Note that the cable fabrication for each end is different.
160
m
0m
5
3
mm
Control unit
Processor unit
150 mm
10/20*/30* m
300 mm
*: Option
Cable XH10P-W-6P L=20/30M
When the RCU-016 is installed, optional cable (XH10P-W-5P-A, L=10/20/30M) is required. Cable
fabrication for each end is the same.
Control unit
Processor unit
150 mm
10/20/30 m
150 mm
Cable XH10P-W-5P-A L=10/20/30M
2-10
Location of connectors
Open the processor unit as shown below to access the 03P9342 board, which is for connection
of external equipment.
Cable clamp
Cables from power supply unit
03P9342
J621
J612
J608
Gyro converter board
or AD-100
J607
External alarm
Speed log
J620
Track control
J611
AIS
J619
J606
Navigator
J605
ECDIS
J603
Gyro converter board
J618
To Sub display *
(SEMI-LOG)
To Sub display *
(FULL-LOG)
From Master radar
J610
J604
PSU
J617
J602
Cable from the
control unit
J616
J614 J615
J601
+12V for card I/F
J613
Heading sensor
Cable from antenna unit
PC
J609
J654
Tx HV line
Coaxial wire
Location of connectors inside the processor unit
*: See page 2-12 for details.
2-11
Cable fabrication for the cables connected to the 03P9342 board
Signal cable RW-9600 (Between antenna unit and processor unit)
Vinyl sheath
Armor
Shield
450
60
5
Expose cores, and then
wind shield around armor.
Vinyl tape
6
14 5 9
Coaxial cable
Conductor
Fold back shield.
Coaxial cable
Fasten cable clamp here.
Power cable TPYC-1.5
Armor
60: Peel paint
L: According to location
of connector.
6
L
Cables for optional equipment (use TTYCS-1 or TTYCS-4, or equivalent)
Armor
60: Peel paint.
Armor
Shield
Sheath
Shield
L= Depends on equipment
connected. Measure at
processor unit.
φ = 10.1 mm
L
5
Conductor
S = 0.75 mm 2
φ = 1.11 mm
TTYCS-1
Vinyl tape
Expose cores, and then
wind shield around armor.
6
Fasten cable clamp here.
Armor
Sheath
φ = 16.3 mm
Shield
Conductor
S = 0.75 mm 2
φ = 1.11 mm
TTYCS-4
2-12
Wiring WAGO connector
Push down.
Fastening coaxial cable
Fasten shield
by clamp.
Terminal opener
Taping
Wire
Twist
WAGO connector
Procedure
1. Twist core.
2. Insert terminal opener as shown and
push down.
3. Insert core into hole.
4. Release terminal opener.
5. Pull wire to confirm that it is firmly in
place.
Fasten conductor with screw.
NOTICE
Fasten BARE conductor. Do not use
crimp-on lug, to prevent increased
contact resistance.
Connection of Sub-display
A conventional remote display and/or FAR-2xx7 series radar can be connected to J617 (FULLLOG) and J618 (SEMI-LOG) in the processor unit as a sub-display. However, the control for GAIN
and STC are different depending on J617 and J618. Refer to the table to connect sub-displays.
Port
Conventional remote display
FAR-2157
J617(FULLOverall gain
LOG)GAIN
and STC are
not conGAIN control
trolled. Video
STC control
signal for
conventional
sub display is
output.
Even if input video level is adjusted
to 4 Vp-p, the gain is 8 db lower
than that on the master radar.
The gain is 8 dB lower than that
on the master radar.
The GAIN control is effective.
The GAIN control has no effect.
The STC control is effective.
The STC control has no effect.
J618(SEMILOG)Video
signal of
main radar
controlled
GAIN and
STC is
output.
Overall gain
When input video level is adjusted
to 4 Vp-p, the gain becomes the
same as that on the master radar.
The gain is almost same as that
on the master radar.
GAIN control
The GAIN control is effective.
The GAIN control has no effect.
STC control
The STC control changes the radar The STC control has no effect.
image, however STC is doubly
applied, resulting in improper radar
picture. Therefore, it is not recommended to use this port.
2-13
2.5 Power Supply Unit
Wire the power supply unit referring to the interconnection diagram. Be sure to ground the unit,
with IV-8sq wire (local supply).
Note 1: Motor specification cannot be changed in the field.
Note 2: Pass the AC line through a double-contact breaker (shipyard supply). Further, for vessels
where the power line is grounded, connect one end of the line to the C (common) terminal and the
other end to the H terminal.
CAUTION
High voltage is present at the
No. 6 pin of TB3. Miswiring at
this pin can damage the unit.
TB3: Power output line, control line
Ground
Cable clamp: Locate armor of cables in clamp.
TB1, TB2: Power input line
Power supply unit, inside view
Fabricating cable connected to terminal TB1, TB2, TB3
Terminal TB1: cable DPYC-2.5
See page 2-8 for sectional view of cable if using equivalent cable.
Armor
30: Remove paint.
FV2-4
120
2-14
Terminal TB2: cable TPYC-2.5 (for antenna motor)
Terminal TB3: #11-#13, cable TYPC-1.5 (between power control section and processor)
See page 2-5 for sectional views of these cables if using equivalent cables.
Armor
30: Peel paint
FV2-4
L
L: 100 (For TPYC-2.5)
150 (For TPYC-1.5)
Terminal TB3: #1-#3 TPYCY-2.5 (between power control section and antenn)
Terminal TB3: #6, #8, #9 TPYCY-1.5 (between power control section and antenna)
Armor
Vinyl sheath
FV2-4
L
30
L: 80 (For TPYCY-2.5)
120 (For TPYCY-1.5)
Armor
φ = TYPCY-1.5: 14.5 mm
TPYCY-2.5: 15.5 mm
Sheath
Conductor
S= TPYCY-1.5: 1.52 mm, TPYCY-2.5: 2.52 mm
φ = TPYCY-1.5: 1.56 mm, TPYCY-2.5: 2.01 mm
2-15
2.6 Changing AC Power Specification
To change AC power specification from 100 VAC to 220 VAC and vice versa, change fuse and
jumper wire settings and adjust the overvoltage detection circuit, following the instructions in this
section.
Processor unit
Add or remove jumper connector P108 from the PWR board 03P9339 and change the fuse in the
processor unit according to ship's mains. Then, adjust the overvoltage detection circuit, the procedure for which is shown on the next page.
Note: When switching from 220 VAC to 100 VAC, construct a jumper connector locally, referring
to the illustration on the next page. (VH8 connector housing is to be plugged into J108.)
Power supply
Fuse
Jumper connector P108
100 VAC
10A
Necessary
220 VAC
5A
Unnecessary
Cover of PWR board
Fuse
TB1
PWR board
Upper part of processor unit
(SPU assembly omitted)
Processor unit, inside view
2-16
J105
J106
PWR board
(P)HV
J104
J103
R21
(OVER)
J101
P108/J108
AC FIL
87654321
Jumper connector
(VH8P)
Processor unit, inside view
How to adjust the overvoltage detection circuit:
1. Add or remove the jumper connector P108 as appropriate and change the fuse, referring to the
table on the previous page for details.
2. On the PWR board, set R21 fully clockwise.
3. Connect a variable transformer between ship's mains and the input power terminal board TB1 in the processor unit.
4. Adjust the variable transformer output (i.e., input voltage to the processor unit) as follows:
For 100 VAC set: 144 VAC
For 220 VAC set: 288 VAC
5. Turn on the radar and rotate R21 counterclockwise gradually until the overvoltage detection circuit activates (i.e., power supply cuts off).
6. Lower the output voltage of the variable transformer and confirm that the radar automatically
turns on with a voltage lower than 142 VAC or 284 VAC.
7. Gradually increase the output voltage of the variable transformer and confirm that the overvoltage detection circuit activates at 144 V or 288 VAC of the variable transformer output.
8. Assemble and connect the processor unit.
2-17
Power supply unit
Refer to the illustration and table below to add (or remove) jumper connector P8 from the TX-HV
Board (03P9350) and change fuse.
After completing jumper and fuse arrangements, adjust the overvoltage detection circuit, using a
variable transformer.
Note: When switching from 220 VAC to 100 VAC, construct a jumper connector locally, referring
to the illustration below. (VH6 connector housing is to be plugged into J8.)
Power
Fuse
Jumper connector P8
100 VAC
5A
Required
220 VAC
3A
Unnecessary
P8/J8
654321
Unfasten four screws and remove
cover for TX-HV Board.
Jumper connector
(VH6P)
CR23
R21
TX-HV Board
Fuse
TB1
How to adjust the overvoltage detection circuit
1. Add or remove the jumper connector P8 as appropriate and change the fuse, referring to the
table above for details.
2. On the PWR board, set R21 fully clockwise.
3. Connect a variable transformer between ship's mains and the input power terminal board
TB-1 in the processor unit.
4. Adjust the variable transformer output (i.e., input voltage to the processor unit) as follows:
For 100 VAC set: 144 VAC
For 220 VAC set: 288 VAC
5. Turn on the radar and rotate R21 counterclockwise gradually until the overvoltage detection circuit activates (i.e., power supply cuts off).
6. Lower the output voltage of the variable transformer and confirm that the radar automatically
turns on with a voltage lower than 142 VAC or 284 VAC.
7. Gradually increase the output voltage of the variable transformer and confirm that the overvoltage detection circuit activates at 144 V or 288 VAC of the variable transformer output.
8. Assemble and connect the power supply unit.
2-18
3. ADJUSTMENTS
This section provides the information necessary for setting and adjusting the radar, which is carried out from the radar's menu system. Menus may be accessed from the keyboard or on-screen
menu in case of Control Unit RCU-014, or on-screen menu in case of Control Unit RCU-015.
The menu illustrations in this chapter show default settings in bold face.
3.1 Initializing Tuning
1. Transmit the radar on 48 nm range.
2. Rotate the [GAIN] control until the value on the gain bar is 70-80.
3. Left-click the MENU box at the right side of the screen.
4. Spin the thumbwheel to choose 1 ECHO and then push the thumbwheel.
[ECHO]
1 BACK
2 2ND ECHO REJ
OFF/ON
3 TUNE INITIALIZE
4 PM
OFF/ON
5 SART
OFF/ON
6 WIPER
OFF/1/2
7 ECHO AREA*1
CIRCLE/WIDE/ALL
8 [PICTURE SELECT]
*1 Not available on IMO or A type radar
ECHO menu
5. Spin the thumbwheel to choose 3 TUNE INITIALIZE.
6. Push the thumbwheel to initialize automatic tuning.
In a few moments echoes appear on the screen. The message "TUNE INITIALIZE" appears (in
red) during automatic tuning. When this message disappears, the tuning is completed. If necessary adjust the [GAIN] control to show echoes clearly.
7. Push the right button twice to close the menu.
3-1
3.2 Heading Alignment
You have mounted the antenna unit facing straight ahead in the direction of the bow. Therefore,
a small but conspicuous target dead ahead visually should appear on the heading line (zero
degrees). In practice, you will probably observe some small bearing error on the display because
of the difficulty in achieving accurate initial positioning of the antenna unit. The following adjustment will compensate for this error.
Correct bearing
relative to heading
α
Target
330
340
α
350 000
010
020
030
320
040
310
050
060
300
070
290
280
080
270
090
260
100
250
110
240
120
230
130
140
220
210
200
150
190
180
170
160
Picture appears
deviated clockwise.
Antenna mounted error
to port (HDG SW
advance)
β
Apparent position
of target
β
Target
330
340
350 000
010
020
030
320
040
310
050
060
300
070
290
280
080
270
090
260
100
250
110
240
120
230
130
140
220
210
Antenna mounted error
to starboard (HDG
SW delayed)
Apparent
position
of target
200
150
190
180
170
160
Correct
bearing
relative to
heading
Picture appears
deviated counterclockwise.
Heading alignment
1. Select a stationary target echo at a range between 0.125 and 0.25 nm, preferably near the
heading line.
2. Operate the EBL control to bisect the target echo:
a) Roll the trackball to place the arrow in the EBL1 or EBL2 box (at bottom left corner), whichever
EBL you want to use.
b) Push the left button to turn on the EBL.
c) Push the left button again to send the cursor inside the effective display area.
d) Roll the trackball (coarse adjustment) or spin the thumbwheel (fine adjustment) to bisect the
target with the EBL.
3. Read the target bearing.
4. Measure the bearing of the stationary target on the navigation chart and calculate the difference
between actual bearing and apparent bearing on the radar screen.
5. Left-click the MENU box at the right side of the screen to close the menu.
3-2
6. For Control Unit RCU-014:
a) While pressing and holding down the [HL OFF] key, press the [MENU] key five times.
b) Press the [0] key to show the INITIALIZE menu.
For Control Unit RCU-015:
See the procedure on the next page for how to show the INITIALIZE menu.
[INITIALIZE]
1
2
3
4
5
6
7
8
BACK
[ECHO ADJ]
[SCANNER]
[INSTALLATION]
[OWN SHIP INFO]
[ARP PRESET]
[NETWORK]
[OTHER]
INITIALIZE menu
7. RCU-014: Press the [2] key to open the ECHO ADJ menu.
RCU-015: Choose 2 ECHO ADJ and then push the thumbwheel.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
8. RCU-014: Press the [3] key to choose HD ALIGN.
RCU-015: Choose 3 HD ALIGN and then push the thumbwheel.
9. RCU-014: Key in the bearing difference. The setting range is 0 to 359.9(°).
RCU-015: Spin the thumbwheel to set the bearing difference and then push the thumbwheel.
The setting range is 0 to 359.9(°).
10.Confirm that the target echo is displayed at correct bearing on the screen and then push the
thumbwheel.
11.RCU-014: Press the [MENU] key to finish.
RCU-015: Left-click the MENU box to finish.
3-3
How to access the INITIALIZE Menu with Control Unit RCU-015
1. Use the trackball to place the
pointer on the MENU box so it
is highlighted. DO NOT click
the menu box - just leave the
pointer over "MENU".
2. Press and hold down the F1
key. Keep it held down during
the next step.
3. Push the right button five times.
You should hear three beeps
on the fifth push.
The INITIALIZE menu appears.
Choose 4 INSTALLATION to
show the installation menus.
How to adjust heading of external radar from this radar
1. Put the cursor in the ANT box at the top left corner then
push the right button.
2. Press the [8] key to select SUB MONITOR.
3. Push the [8] key until ON is selected then push the left button.
4. Push the right button.
5. Left-click the ANT box to select SUB MONITOR.
6. Follow the procedure on page 3-3.
3-4
3.3 Adjusting Sweep Timing
Sweep timing differs with respect to the length of the signal cable between the antenna unit and
the processor unit. Adjust sweep timing to prevent the following symptoms:
• The echo of a "straight" target (for example, pier), on the 0.25 m range, will appear on the display as being pulled inward or pushed outward. See the figure below.
• The range of target echoes will also be incorrectly shown.
(1) Correct
(2) Target pushed
inward
(3) Target pushed
outward
Examples of correct and incorrect sweep timings
1. Transmit on the 0.25 nm range.
2. Adjust the radar picture controls to display picture properly.
3. Select a target echo which should be displayed straightly.
4. On the ECHO ADJ menu, choose 4 TIMING ADJ.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
5. Spin the thumbwheel to set a suitable value which causes the target to be displayed straightly.
The setting range is 0 to 4095.
6. Left-click the MENU box to finish.
Note:The sweep timing of an external radar can be adjusted from this radar. Do steps 1-5 on page
3-4 and then do the procedure on this page.
3-5
3.4 Suppressing Main Bang
If main bang appears at the screen center, suppress it as follows.
1. Transmit the radar on a long range and then wait ten minutes.
2. Adjust gain to show a slight amount of noise on the display.
3. Select the 0.25 nm range. Adjust sea clutter control to suppress sea clutter.
4. On the ECHO ADJ menu, choose 5 MBS.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
5. Spin the thumbwheel to set a suitable value so that the main bang disappears. The setting
range is 0 to 255.
6. Left-click the MENU box to finish.
3-6
3.5 Other Settings
ECHO menu setting
Open the ECHO ADJ menu as described on page 3-3 and 3-4.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5/4.2
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
CABLE ATT ADJ
Before adjusting, set the radar as follows (Same as default setting of PICTURE1):
IR: 2, ES: off, EAV: off, 24nm range, long pulse
To adjust the cable attenuation manually, choose MANUAL and push the thumbwheel. With
the gain set to 80, spin the thumbwheel until noise just appears on the screen. Default setting is
30 for the antenna cable length of 15 m. The setting range is 0 to 73.
To adjust the cable attenuation automatically, choose AUTO and push the thumbwheel. The
message "CABLE ATT ADJ" appears (in red) at the bottom of the screen. It takes about five minutes to complete the adjustment, after which the radar goes into stand-by.
DEFAULT ANT HEIGHT
Select height (m) of the radar antenna unit from the sea surface from among 5, 7.5, 10, 15, 20,
25, 30, 35, 40, 45 and "more 50 m".
NEAR STC CURVE, MID STC CURVE AND FAR STC CURVE
The default setting is suitable for most conditions. If necessary, change the setting according to
sea conditions.
RING SUPPRESSION
This is mainly used to removes "ring" noise that appears in the waveguide-type radar. Adjust so
the rings disappear at the range of 0.125 nm. The setting range is 0 to 255.
3-7
SCANNER menu
1. Open the INITIALIZE menu as described on page 3-3 and 3-4.
2. Choose 3 SCANNER to open the SCANNER menu.
[SCANNER]
1 BACK
2 BLIND SECTOR 1
START 000°
ANGLE 000°
3 BLIND SECTOR 2
START 000°
ANGLE 000°
4 ANT REVOLUTION
LO/HI/AUTO
5 ANT SW
OFF/ON/EXT
6 ANT STOPPED
STBY/TX
7 M SPEC
OFF/ON
8 BB TYPE
NORMAL/BB
SCANNER menu
BLIND SECTOR 1 and BLIND SECTOR 2
Set area (up to 2) where no radar pulses will be transmitted. Heading should be adjusted before
setting any blind sector. For example, set the area where an interfering object at the rear of the
antenna would produce a dead sector (area where no echoes appear) on the display. To enter an
area, enter start bearing (relative to heading) and dead sector angle. To erase the area, enter 0
for both the START and ANGLE options. The setting range of START is 0 to 359 and ANGLE is
0 to 180 .
ANT REVOLUTION
No use.
ANT SW and ANT STOPPED
This is used for antenna maintenance by service personnel.
M SPEC
No use.
BB TYPE
Choose type of radar. Select "BB" for FAR-2157-BB.
3-8
INSTALLATION menu
Open the INSTALLATION menu by choosing 4 INSTALLATION from the INITIALIZE menu.
RADAR
Automatically selected to MAIN when 4 RADAR NO is
selected to 1-4; SUB when the same item is selected to
5-8.
RANGE UNIT
Choose NM, SM, km or kyd (kilo yard) as appropriate. For
the IMO- and A-type radars the range unit is fixed at "NM".
RADAR NO and RADAR POSN
For multiple radar system using the network hub, set
number (name) and antenna position for each system, to
easily distinguish radars from one another.
MODEL
Choose "50".
TYPE
Choose radar type from among the following options:
IMO: IMO compliant
A: Near-IMO specifications
B: International fishing vessels
C: Japanese flag vessels
W: Washington state (USA) ferry
[INSTALLATION]
1 BACK
2 RADAR*1
MAIN/SUB
3 RANGE UNIT*2
NM/SM/km/kyd
4 RADAR NO*3
1/2/3/4/5/6/7/8
5 RADAR POSN
FORE/MAIN TOP/
MAIN 2ND/MAIN 3RD/
AFT/PORT/
STARBOARD
6 MODEL
6/12/25 UP/25 DOWN/
50/30 UP/30 DOWN/60
7 TYPE
IMO/A/B/C/W
8 ON TIME
XX.XH
9 TX TIME
XX.XH
*1: No selection
*2: Not shown on IMO- or A-type radar.
*3: No.1-4: with antenna unit
No.5-8: without antenna unit
INSTALLATION menu
ON TIME and TX TIME
These items show number of hours the radar has been turned on and transmitted, respectively.
Value can be changed; for example, after replacing magnetron TX Time can be reset to 0.
3-9
OWN SHIP INFO menu
Open the OWN SHIP INFO menu by choosing 5 OWN SHIP INFO from the INITIALIZE menu.
[OWNSHIP INFO]
1 BACK
2 LENGTH/WIDTH
LENGTH 100 m
WIDTH
50 m
3 SCANNER POSN
BOW
0m
PORT 0 m
4 SUB SCANNER POSN
BOW
0m
PORT 0 m
5 GPS1 ANT POSN
BOW
0m
PORT 0 m
6 GPS2 ANT POSN
BOW
0m
LEFT 0 m
7 CONNING POSN
BOW
0m
PORT 0 m
OWN SHIP INFO menu
LENGTH/WIDTH, SCANNER POSN and SUB SCANNER POSN
To accurately inscribe own ship marker on the screen, enter length and width of the ship and
scanner position from the bow and left sides, for both main and sub scanners. The setting ranges
are as follows:
LENGTH:
WIDTH:
BOW:
LEFT:
0 to 999 m
0 to 999 m
0 to 999 m
0 to 999 m
GPS 1 ANT POSN and GPS 2 ANT POSN
This is for AIS. Enter the GPS antenna position, from the bow and left side. The setting ranges are
the same as above.
CONNING POSN
Enter the conning position, from the bow and left side. The setting ranges are the same as those
shown on the preceding page. When you set the reference point as the conning position, these
values are used to correct the radar antenna position.
Note: If two or more radars are installed, all items on the OWN SHIP INFO menu should be the
same except 3 SCANNER.
3-10
ARPA PRESET menu
Open the ARPA PRESET menu by choosing 6 ARP PRESET from the INITIALIZE menu.
[TRACK PRESET]
[ARP PRESET]
1 BACK
2 TTM OUTPUT
OFF/REL/TRUE
3 MAX RANGE
24/32
4 ECHO LEVEL
16
5 QV DISPLAY
OFF/ON
6 ARP W/O GYRO*
OFF/ON
7 [ACQ PRESET]
8 [TRACK PRESET]
9 [ARP SENSOR DATA]
0 DEFAULT
[ACQ PRESET]
1 BACK
2 LAND SIZE
800 M
3 ANT SELECT
XN12AF/XN20AF/
XN24AF/XN4A/XN5A
SN30AF/SN36AF/
SN4A/SN5A
4 AUTO ACQ CORRE
5 SCAN
5 AUTO ACQ WEED
1 SCAN
1 BACK
2 GATE SIZE
S/ M /L/LL
3 FILTER RESPONSE
1/ 2 /3/4
4 LOST COUNT
9 SCAN
5 MAX SPEED
100 KTS
6 TRACKING MODE
1 /2/3/4
7 START TIME TGT VECT
TIME /SCAN
50 SEC
20 SCAN
*: Not shown on IMO radar.
ARP-related menus
TTM OUTPUT
Set the output format of tracked targets among OFF, REL and TRUE.
OFF:
No output
REL (relative):Target bearing from own ship, degree relative.
Target course, degree relative.
TRUE:
Target bearing, degree true.
Target course, degree true.
Note: The TTM OUTPUT port changes according to the setting for INS as described on page 313.
INS-OFF:
Output from J619 port
INS-SERIAL: Output from J620 port
INS-LAN:
Output from NETWORK port
MAX RANGE
Choose the maximum ARPA tracking range, 24 or 32 nm.
ECHO LEVEL
Set echo detection level. The setting range is 1 to 31.
QV DISPLAY
OFF: Normal picture
ON: Quantized picture. Always off at power on.
ARP W/O GYRO (Not shown on IMO radar)
ARPA may be used without a gyrocompass. Choose ON to use ARPA without a gyrocompass.
3-11
LAND SIZE
Set the minimum echo size to be considered a landmass. The setting range is 100 to 1000 m, in
increments of 100 m.
ANT SELECT
Set the model of antenna radiator used.
AUTO ACQ CORRE
Set the number of consecutive echoes to receive from a target before initiating automatic acquisition on it. The setting range is 3 to 10.
AUTO ACQ WEED
Set the number of consecutive "no echoes" from a target before canceling automatic acquisition
on it. The setting range is 1 to 5.
GATE SIZE
Set the gate size among S, M, L, or LL.
FILTER RESPONSE
Set the filter response function. The setting range is 1 to 4. Choose 1 for better trackability; 4 for
better stability.
LOST COUNT
Set the number of consecutive "no echoes" before an acquired target is declared as a lost target.
The setting range is 1 to 20.
MAX SPEED
Set the maximum tracking speed. The setting range is 40 to 150.
TRACKING MODE
Set the tracking mode among 1 to 4.
START TIME TGT VECT
Choose how to wait from time of acquisition to display of vector. Choose TIME to set by time (seconds) or SCAN to set by number of antenna scans.
3-12
OTHER menu
Open the OTHER menu by choosing 8 OTHERS from the INITIALIZE menu.
[OTHERS]
1 BACK
2 DEMO ECHO
OFF/EG/SPU/PC
3 EAV w/o GYRO
OFF/ON
4 ARP SELECT
ARPA/ATA
5 INS
OFF/SERIAL/LAN
OTHER menu
EAV w/o GYRO
Echo averaging can be used without a gyrocompass. Choose ON to use echo averaging without
a gyrocompass.
ARP SELECT
Choose ARPA or ATA depending on your radar system.
INS
Choose appropriate item according to the ECDIS connected.
OFF:
No connection
SERIAL: When connecting FEA-2105 series ECDIS.
LAN:
When connecting FEA-2107 series ECDIS.
3-13
This page intentionally left blank.
3-14
4. OPTIONAL EQUIPMENT
4.1 Gyro Converter GC-10
The Gyro Converter GC-10, incorporated inside the processor unit, converts analog gyrocompass
reading into digital coded bearing data for display on the radar screen.
This section explains how to install the GC-10 (mainly consisting of the GYRO CONVERTER
board) and set it up according to the gyrocompass connected.
Installing the GYRO CONVERTER board
Necessary Parts: Gyro Converter GC-10-2 (Code no. 000-080-440)
See packing list at the back of this manual for details.
1
3
1
12
3
1
4
1. Open the processor unit.
2
1
1
12
1
1
1
5
1
1
3
7
Processor unit, inside view
4-1
2. Fasten the GYRO CONVERTER board inside the processor unit with five washer head screws.
3. Fix connector 231-607/019-FUR (called J602) with two screws.
Screw
M3X8 5 pcs
GYRO CONVERTER board
64P1106A
Screw
M2.6X10 2 pcs
1
7
Connector (231)
231-107/026-FUR
7
1
Connector (231)
231-607/019-FUR
PCB 03P9342
Fixing GYRO CONVERTER board inside the processor unit
4. Connect the GYRO CONVERTER board to the 03P9342 board with XH-PH 03-2088 connector
assy. (6-14P) and NH connector assy. 03-2091.
4-2
5. Connect J602 (attached at step 3) to the GYRO CONVERTER board with two VH connector
assemblies 03-2089 (3P) and 03-2090 (5P).
Wiring WAGO connector
Press downward.
Terminal opener
Connection for J602
2
J602
P608
1 2 3 4
7 6 5 4 3 2 1
PPL
BLU
GRN
YEL
ORG
From J5 RED
BRN
From J4
Connection for P608
1
YEL
ORG
RED
BRN
WAGO connector
Twist
2
2
Wire
Procedure
1. Twist core.
2. Press terminal opener downward.
3. Insert wire to hole.
4. Remove terminal opener.
5. Pull wire to confirm that it is secure.
VH connector assy.
03-2089 (5P)
VH connector assy.
03-2090 (3P)
P5
1
To J602
XH-PH connector assy.
03-2088 (6-14P)
To P608
P7
P4
NH connector assy.
03-2091 (5P)
P1
P603
4
J5
1
3
1
1
1
12
1
1
5
J602
1
2
1
7
J603
1
J7
3
12
P608
GYRO CONVERTER J1
64P1106A
J4
TB
03P9342
Connecting connector assemblies inside processor unit
6. Confirm gyrocompass specifications and set up the DIP switches and jumper wires on the
GYRO CONVERTER board according to gyrocompass connected:
• Setting jumper wires and DIP switches by gyrocompass specifications: page 4-6
• Setting jumper wires and DIP switches by make and model of gyrocompass: page 4-7
• Location of jumper wires and DIP switches: page 4-8
4-3
7. Pass the gyrocompass cable through the cable clamp and connect it to connector J602 as
shown in the figure below.
8. Attach the clamps to the plastic cover and then attach the cover to the GYRO CONVERTER
board as shown in the figure below. Pass cables thru the clamp ED-1.
Screw
M4X8 3 pcs
Plastic cover
Clamp CKS-10-L
Clamp EDS-1
Insert cables to these
clamp.
2
1
12
1
1
1
5
1
1
1
7
3
1
3
1
12
3
1
4
Clamp CKS-13-L
Attaching plastic cover for GYRO CONVERTER board
9. Close the processor unit.
4-4
Connection of external power supply
An external power supply is necessary when the repeater signal is step-by-step type and the step
voltage is below 20 V or output voltage is less than 5 W.
1. Cut jumper wire JP1 on the GYRO CONVERTER board when an external power supply is
used.
2. Connect the gyrocompass cable and power cable as shown below.
GYRO CONVERTER board
[A] 64P1106
External Power Supply
20 - 135 VAC
20 - 100 VDC
J5
1 > R2
2 > R1/COM
Either connection
in case of DC
polarity.
S2
J4
1 > S1
2 > S2
S3
3 > S3
S1
Gyrocompass
(Step type)
COM
F.G.
4>T
5 > F.G.
Connection of external power supply to GYRO CONVERTER board
DIP switch, jumper wire settings
Default setting
The gyro converter GC-10 is set at the factory for connection with the gyrocompass specifications
below.
AC synchronous signal:50/60 Hz
Rotor voltage:
60 V to 135 V AC
Stator voltage:
60 V to 135 V AC
Gear ratio:
360x
Supply voltage:
30 V to 135 V AC
If the specifications of the gyrocompass differ from those mentioned above, change jumper wire
and DIP switch settings on the GYRO CONVERTER board. Settings may be changed according
to gyrocompass specifications (see page 4-6) or make and model of gyrocompass (see page 47). For the location of DIP switches and jumper wires, see page 4-8.
Note: If you change the setting with the power turned on, set #8 of SW2 from OFF to ON, then
OFF again to effect changes.
4-5
Setting method 1: DIP switch settings and gyrocompass specifications
1) Gyrocompass type
2) Frequency
50/60 Hz
SW
1-7
OFF
SW
1-8
OFF
#2, #3, #4
400 Hz
ON
OFF
OFF
#4, #5, #6
500 Hz
OFF
ON
ON
OFF
#4, #5, #6
DC
ON
ON
ON
OFF
#4, #5, #6
Gyrocompass
type
AC synchronous
SW
1-4
OFF
SW
1-5
OFF
SW
1-6
OFF
#1, #2, #3
DC synchronous
OFF
OFF
OFF
DC step
ON
OFF
Full-wave
pulsating current
Half-wave
pulsating current
OFF
ON
JP1
3) Rotor voltage (between R1 & R2)
Rotor Voltage
20 to 45 VAC
30 to 70 VAC
40 to 90 VAC
60 to 135 VAC
SW2-1
ON
OFF
ON
OFF
Remarks
AC synchronouspulsating current
AC synchronouspulsating current
AC synchronouspulsating current
DC synchronous
DC step
4) Stator voltage (between S1 & S2)
JP3
#2
#2
#1
#1
5) Ratio
Ratio
360X
180X
90X
36X
Frequency
Stator Voltage
SW2-2
20 to 45 VAC, or 20 to 60 VDC
ON
30 to 70 VAC, or 40 to 100 VDC OFF
40 to 90 VAC
ON
60 to 135 VAC
OFF
SW2-3
OFF
OFF
OFF
OFF
JP2
#2
#2
#1
#1
6) Supply voltage
SW1-1
OFF
ON
OFF
ON
SW1-2
OFF
OFF
ON
ON
SW1-3
OFF
OFF
OFF
OFF
7) AD-10 format data
Select data Tx interval for ports 1 to 6 with
jumper wires JP6 and JP7. The Tx interval
is available in 25 msec or 200 msec. Use
25 msec for radar.
9) NMEA-0183
Version no.
Version no. SW3-1
1.5
OFF
2.0
ON
Stator Voltage
20 to 45 VAC, or 20 to 60 VDC
30 to 70 VAC, or 40 to 100 VDC
JP4
#2
#1
JP5
#2
#1
8) NMEA-0183 Tx interval and output sentence
Tx
interval
SW
2-5
SW
2-6
1s
OFF
OFF
HDT+VHW
200 ms
ON
OFF
HDT
100 ms
OFF
ON
HDT
25 ms
ON
ON
HDT
10) NMEA-0183
baud rate
Baud rate SW3-2
4800 bps
OFF
38400 bps
ON
11) Power fail
detection
Talker
SW3-3
Disable
OFF
Enable
ON
Output sentence
12) Stator signal
loss detection
Detection
SW2-7
Yes
OFF
No
ON
(Use OFF for radar only)
SW2-4: factory use only
SW3-4: not used
After setting jumpers and DIP switches, reset the power or set SW2-8 to “CPU”.
4-6
Setting method 2: by make and model of gyrocompass
Maker
Models
Specification
SW
1-1
SW
1-2
SW
1-3
SW
1-4
SW
1-5
SW
1-6
SW
1-7
SW
1-8
SW
2-1
SW
2-2
SW
2-3
JP 1
JP 2
JP 3
JP 4
JP 5
Anschutz
Standard 2,3
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 22V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
#1,
#2,#3
#2
#2
#1
1
#
Standard 4,6
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 90V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#2
#1
#1
1
#
Standard 20
DC step
35V 180x
COM(-) ,3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
2
#
C-1/1A/2/3
A-55, B-55
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 22V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
#1,
#2,#3
#2
#2
#1
1
#
CMZ-700
DC step
24V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF Remove
#2
-
*
*
CMZ-250X/
300X/500
DC synchronous 360x
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
-
ON
OFF
Remove
#2
-
*
*
DC step
35V 180x
COM(+),3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
AC synchronous
50/60Hz
Rotor voltage: 100V
Stator voltage: 90V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
step
35V 180x
See note below. COM(+),3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
Remove
#2
-
*
*
Plath
NAVGAT II/III
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 68V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#2
#2
#1
#1
Tokimec
(Sperry
type)
ES-1/2/11
GLT-101/102/
103/106K/107
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 90V
36x
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
ES-11A/110
TG-200
PR222R/2000
PR237L/H
GM 21
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 22V
90x
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
MK-14
MOD-1/2/T
NK-EN,NK-EI
DC step
70V 180x
COM(-), 3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
SR-130/140
DC step
70V 180x
5-wire, open collector
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
TG-100/5000
PR-357/130/
140, ES-17
GLT-201/202
/203
DC step
70V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
TG-6000
DC step
24V 180x
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
GM-11
AC synchronous
50/60Hz
Rotor voltage: 100V
Stator voltage: 90V
90x
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
SR-120,ES-16
MK-10/20/30
DC step
35V 180x
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
Kawasaki
GX-81
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 90V
90x
OFF
ON
OFF OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
Armabrown
MK-10,MKL-1
SERIES1351,
MOD-4
DC step
50V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
Robertson
SKR-80
DC step
35V 180x
COM(-), 3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
Yokogawa
Navtec
(Pla th
type)
CMZ-100/200/
300
C-1Jr,D-1Z/1/3
IPS-2/3
CMZ-50
OFF
OFF
*: Set JP4 and JP5 according to the voltage of the external power supply.
Note: If CMZ-50 has 35 VDC, set JP1 to #4, #5, #6.
4-7
Location of DIP switches, jumper wires on the GYRO CONVERTER board
JP5, JP4
(Supply voltage)
JP2
(Stator voltage)
JP3
(Rotor voltage)
64P1106
JP1
(Gyro type)
SW3
DIP switch
J12
(Data output
port #6)
J11
(Data output
port #5)
J10
(Data output
port #4)
SW2
DIP switch
Fuse
(2A)
SW1
J4
DIP switch
(Stator signal input)
J5
(Rotor signal input,
external power input)
J6
(IEC-61162-1 output port)
GYRO CONVERTER board
4-8
JP6, JP7
(AD format
data Tx interval)
J9
(Data output port #3)
J8
(Data output port #2)
J7
(Data output port #1)
Setting the heading readout on the radar display
Confirm that the gyrocompass is giving a reliable readout. Then, set the heading readout on the
radar display with the gyrocompass readout as follows:
1. Right-click the HDG box at the top right corner on the screen.
[HDG MENU]
1 HDG SOURCE
AD-10/SERIAL
2 GC-10 SETTING
000.0
HDG menu
2. Spin the thumbwheel to choose 1 HDG SOURCE and push the left button.
3. Spin the thumbwheel to choose AD-10 and push the left button.
4. Spin the thumbwheel to choose 2 GC-10 SETTING and push the left button.
5. Spin the thumbwheel to set gyrocompass reading and push the left button.
6. Push the right button close the menu.
4-9
4.2 Memory Card Interface Unit
Mounting considerations
When selecting a mounting location, observe the following points:
•
•
•
•
Locate the unit away from heat sources because of heat that can build up inside the cabinet.
Locate the unit away from places subject to water splash and rain.
Leave sufficient space at the sides and rear of the unit to facilitate maintenance.
A magnetic compass will be affected if the unit is placed too close to the magnetic compass.
Observe the compass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Flush mounting
This unit can be flush-mounted in a panel with the standard installation materials.
1. Prepare a cutout in the mounting location, referring to the outline drawing at the end of this
manual.
2. Screw in the threaded rods to the flange on the front panel of the unit securely by hands.
3. Set the unit to the cutout.
4. Insert the flat washer, spring washer and nut in that order for each rod and fasten the nuts.
Flush mounting dimensions for memory card interface unit
4-10
Desktop mount
Requires the optional desktop mount kit FP03-10201. Refer to the packing list at the back of this
manual for further information about this kit.
1. Fix the mounting bracket 19-023-3081 to the unit with four screws.
2. Mount the above assembly on a desktop with four self-tapping screws.
Connections
One memory card IF unit and one processor unit
Connect as shown below.
Processor unit
J614
NETWORK
12 VDC
MJ-A3SPF0015-100 (10 m)
Memory card IF unit
12 VDC
two mini-cards
PSE-4PTX-BL (10 m)
NETWORK
RJ-45
Connections for one memory card interface unit
One memory card IF unit and multiple processor units
Prepare optional armored LAN cable kit and Switching Hub HUB-100. Connect as shown below.
No.1
J614
Processor
unit
NETWORK
12 VDC
MJ-A3SPF0015-100 (10 m)
FR-FTPC-CY (10/20/30 m)
(straight)
Memory card IF unit
12 VDC
NETWORK
FR-FTPC-CY (10/20/30 m)
(straight)
No.2
Processor
unit
No.3
Processor
unit
No.4
Processor
unit
two mini-cards
Switching hub
FR-FTPC-CY
(10/20/30 m)
(straight)
HUB-100
(option)
FR-FTPC-CY (10/20/30 m) (straight)
FR-FTPC-CY (10/20/30 m) (straight)
Connecting one memory card interface unit and multiple processor units via switching hub
4-11
it
Armored LAN cable kit
Type
Code No.
Contents
OP03-28900
000-082-658
Cable FR-FTPC-CY (10 m), Modular connector (2 pcs.)
OP03-28910
000-082-689
Cable FR-FTPC-CY (20 m), Modular connector. (2 pcs.)
OP03-28920
000-082-660
Cable FR-FTPC-CY (30 m), Modular connector (2 pcs.)
Note: When two memory card interface units are connected via a network, change ID code for the
second unit.
1. Remove the cover and set the IP0 bit of the DIP switch S1 on the CARDCPU board (03P9333)
to ON.
2. Set INIT bit of S1 to ON and turn on the radar. Wait until CR2 starts blinking. DO NOT turn off
the power until CR2 starts blinking.
3. Turn off the power and set INIT bit to OFF.
ON
J314
OFF
IP0
IP1
IP2
CR2
S1
INIT
(Default: all OFF)
CARDCPU board 03P9333
Memory card interface unit, showing location of DIP switch S1
4-12
4.3 DVI-RGB Conversion Kit
This information provides the procedure necessary for the installation of the DVI-RGB conversion
kit. This kit is installed in the processor unit to enable connection of an RGB monitor or VDR
(Voyage Data Recorder).
Name:
DVI-RGB conversion kit
Type:
OP03-180-2
Code no.: 008-536-070
See packing list for contents. Refer to the figure below for modification.
DVI-RGB CONVERSION board
(SLB-FRN4-A)
DVI cable
M3x8
6 pcs
J9
(10 pin)
J4
(6 pin)
J3
J615
03-2094
03-2092
03P9342 board
03-2093
Spacer
SQ-35
6 pcs
M3x8
4 pcs
J1
(13 pin)
RGB-BUFF board
(03P9229B)
D-sub 15P
Female
J2
J3
(3 pin)
RGB Cable
(User supply)
Spring washer
Fixing
holes
Boss
Ferrite core
To external monitor or
BNC connector converter
(see page 4-15).
Clamp copper tape
section by cable clamp.
Ferrite core side: Connect to DVI-D port on
the upper part of the processor unit.
How to wire the DVI-RBG conversion board
4-13
1. Remove the top cover and open the upper part of the processor unit.
DVI-D port
(Connect DVI cable at step 12.)
Processor unit, side view
2. Fix the RGB-BUFF board (03P9229B board) with four screws. (See the figure below.)
3. Attach the connector assemblies to J1 and J3 on the 03P9229B board as follows.
J1: 13-pin connector of the connector assembly 03-2094
J3: 3-pin connector of the connector assembly 03-2093
4. Attach six sets of spring washers and spacers at the locations shown below.
Spring washer, spacer
J1
03P9229B board
J2 (Connect RGB Cable at step 10.)
J3
J2
03P9342 board
J615 (Connect connector assembies at step 8.)
Processor unit (bottom chassis)
4-14
5. Attach the DVI-RGB CONVERSION board to the location shown below.
DVI-RGB
CONVERSION board
J3 (Connect DVI cable at step 9.)
J9
J4
Fixing the DVI-RGB conversion board inside the processor unit
6. Attach the 10-pin connector from J1 on the 03P9229B board to J9 on the DVI-RGB board.
7. Attach the connector assembly 03-2092 to J4 on the DVI-RGB CONVERSION board.
8. Remove connector housing J615 from the 03P9342 board. Connect the cable from J3 on the
03P9229B board and the cable from J4 on the DVI-RGB CONVERSION board to J615. Attach
J615 to the 03P9342 board.
To connect wires to the WAGO connector, use the terminal opener (supplied as installation
materials) as shown below.
Terminal opener
J615 Housing
1) Press downward.
1
2
BRN
RED
ORG
YEL
GRN
3
4
5
2) Insert core.
Connecting wires to the housing
9. Connect the DVI cable to J3 on the DVI-RGB CONVERSION board. Connect the end that does
not have the ferrite core.
10.Pass an RGB cable (local supply) through the cable clamp and connect it to J2 on the
03P9229B board.
11.Pass the DVI cable through the cable clamp, laying the section with copper tape in the cable
clamp.
12.Assemble the processor unit and connect the other end of the DVI cable to the DVI-D port.
4-15
4.4 BNC Connector Converter
To connect the FURUNO Voyage Data Recorder VR-5000 to this radar, the DVI-RGB conversion
kit (mentioned at previous paragraph) and the BNC connector converter are required. Also VGA
cable (between the processor unit and the BNC connector converter) and five 75 ohm coaxial
cables (between the BNC connector converter and VR-5000) are required.
FAR-2157(-BB)
PROCESSOR UNIT
DVI-RGB
Conversion kit
BNC CONNECTOR
R
CONVERTER
DSUB-BNC-1
G
VGA cable
D-sub 15P
Female
D-sub 15P
Male
75 W coax. cable
VD1
R
VR-5000
DATA COLLECTING
UNIT
G
B
B
H
HS
V
VS
Connecting VR-5000 to FAR-2157(-BB) via BNC connector converter
BNC connnector converter
4-16
5. IO DATA
Available input and output data are shown in the tables below and input and output sentences are
shown on the next page.
Note: This radar accepts position data fixed by WGS-84 geodetic datum only. Set the datum to
WGS-84 on the EPFS (GPS, etc.) connected to this radar. If other type of datum is input, the error
message "DATUM" appears and the AIS feature is inoperative.
Input
Data
Heading
signal
Specifications
Contents
Synchro or step
GC-10 required
AD-10 format
External AD-100
Remarks
Switching between AD-10
and IEC 61162 is done
from menu.
IEC 61162-2
Speed signal
IEC 61162-1
Navigator
data
IEC 61162-1
Position, course, speed, LORANC TD, waypoint, route, time, wind
speed and direction, current data,
depth, water temperature, roll,
pitch, ROT
External
radar signal
Heading, Bearing,
Trigger, Video
No GAIN, STC control
Alarm ACK
input
Contact closure
signal
Operate as remote display
Input signal from alarm
system
Track Control RS-422
unit
Option
Output
Data
Specifications
Contents
Remarks
Radar system
data
RS-232C
RSD, OSD, TLL
For PC plotter
ARPA data
IEC 61162-1
TTM
For ECDIS
Remote display
signal
Heading, Bearing, Tx
Trigger, Video
External LCD
monitor signal
DVI
Same as main monitor unit
2 systems max.
External CRT
monitor signal
R, G, B, H, V
Same as main monitor unit
Option
Alarm signal
Contact closure
signal
Output to alarm system by using
photo-relay
4 outputs, output
content selected from
menu.
2 ports
5-1
IEC 61162 input sentence and priority
Item
Sentence and order of priority
Speed (STW)
Speed (SOG
Speed (position)
Heading (True)
Position
Waypoint
Date
Depth
Water temperature
Wind
VBW>VHW
VBW
VTG>RMC
HDT*
GGA>GLL>RMC>RMA
BWR>BWC>RMB
ZDA
DPT>DBT>DBS
MTW
MWV
IEC 61162 output sentence
Item
Target L/L
Radar system data
Own ship data
ARPA target data
Sentence
TLL (Not on IMO radar)
RSD
OSD
TTM
HDT is IEC61162-2, all other sentences are IEC61162-1 ed2.
5-2
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
A-2
0#/'
176.+0'
࡙࠾࠶࠻
$': :0#
&'5%4+26+10%1&'ͳ
36;
70+6
㨻㩧㩍㩏
:0#
#06'00#
㩖㨲㨺㩎㩨9)
(''&'49)#55'/$.;
#06'00#+056#..#6+10/#6'4+#.5
1㩢㩧㩂㩨
:0#
#5
59㨻㩣㩚㩋㨷㨺㩖㩨)‫ޓ‬
59㨻㩣㩚㩋㨷㨺㩖㩨)
㩃㩚㩆㨺㩣
5+.+%1047$$'4
㩔㩨㩒ᐳ㊄
/575
ࡃࡀᐳ㊄
/575
9#8')7+&'%.#/2
+057.#614
౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
*':*'#&5.16$1.6$
9#5*'4
౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎
*':#)10#.*'#&5.16
$1.6
౐ⷺ㩇㩢㩦㩢㩘㩨㩣㩎
*':#)10#.*'#&5.16
$1.6
౐ⷺ㩇㩢㩦㩢㩘㩨㩣㩎
524+0)9#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
/575
*':#)10#.*'#&5.16
$1.6
౐ⷺ㩏㨹㩎‫ޓ‬㩆㨷
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
/575
(4
45$
524+0)9#5*'4
36;
9)%.#/2
14+0)
&'5%4+26+10%1&'ͳ
ዉᵄ▤㑆ᐳ
176.+0'
)4170&+0)9+4'
ዉᵄ▤᛼ߐ߃'ဳ
:0#
㨻㩧㩍㩏Ꮏ᧚
0#/'
✢᧚ടᎿຠ
41*5
/:575
/:575
/:575
/:575
/575
*':076
(.#69#5*'4
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ㪆䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
ဳᑼ䎒䱤䱚䱮䲈⇟ภ䬛䯾Ბ䬽႐ว䫺ਅᲑ䭗䭙਄Ბ䬺ઍ䭞䭚ㆊᷰᦼຠ䬶䬑䭙䫺䬸䬰䭘䬚䬛౉䬲䬵䬓䭍䬨䫻䫹䬹䬙䫺ຠ⾰䬾ᄌ䭞䭙䭍䬪䭢䫻
䎷䎺䎲䎃䎷䎼䎳䎨䎶䎃䎤䎱䎧䎃䎦䎲䎧䎨䎶䎃䎰䎤䎼䎃䎥䎨䎃䎯䎬䎶䎷䎨䎧䎃䎩䎲䎵䎃䎤䎱䎃䎬䎷䎨䎰䎑䎃䎃䎷䎫䎨䎃䎯䎲䎺䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎃䎰䎤䎼䎃䎥䎨䎃䎶䎫䎬䎳䎳䎨䎧䎃䎬䎱䎃䎳䎯䎤䎦䎨䎃䎲䎩䎃
䎷䎫䎨䎃䎸䎳䎳䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎑䎃䎴䎸䎤䎯䎬䎷䎼䎃䎬䎶䎃䎷䎫䎨䎃䎶䎤䎰䎨䎑
$':
03GX-X-9851
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
コ-ド番号末尾の[**]は、選択品の代表コー ドを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
INSTALLATION MATERIALS
工事材料
008-572-970-00
CP03-31301
008-424-380-00
INSTALLATION MATERIALS
工事材料
SPARE PARTS
予備品
SPARE PARTS
予備品
ANTENNA DRIVE UNIT
空中線本体部組品
型式/コー ド番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
1
1
SP03-09203
000-090-655-00
**
1
RSB-106-083-S/RSB-107-083-S
DESCRIPTION/CODE №
O U T L I N E
UNIT
N A M E
ユニット
RSB-106-083-S/RSB-107-083-S
PACKING LIST
03GX-X-9851 -0
Q'TY
1/1
A-1
䯴⇛࿑䬽ኸᴺ䬾䫺ෳ⠨୯䬶䬨䫻䎃䎧䎬䎰䎨䎱䎶䎬䎲䎱䎶䎃䎬䎱䎃䎧䎵䎤䎺䎬䎱䎪䎃䎩䎲䎵䎃䎵䎨䎩䎨䎵䎨䎱䎦䎨䎃䎲䎱䎯䎼䎑䯵
176.+0'
&'5%4+26+10%1&'ͳ
#06'00#
:0#
1㩢㩧㩂㩨
#06'00#+056#..#6+10/#6'4+#.5
#5
㩃㩚㩆㨺㩣
5+.+%1047$$'4
㩔㩨㩒ᐳ㊄
59㨻㩣㩚㩋㨷㨺㩖㩨)‫ޓ‬
59㨻㩣㩚㩋㨷㨺㩖㩨)
/575
ࡃࡀᐳ㊄
*':*'#&5.16$1.6$
9#5*'4
౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎
*':#)10#.*'#&5.16
$1.6
౐ⷺ㩇㩢㩦㩢㩘㩨㩣㩎
*':#)10#.*'#&5.16
$1.6
౐ⷺ㩇㩢㩦㩢㩘㩨㩣㩎
/575
*':#)10#.*'#&5.16
$1.6
౐ⷺ㩏㨹㩎‫ޓ‬㩆㨷
524+0)9#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
/575
)::
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
*':#)10#.076
౐ⷺ㩏㨹㩎㩆㨷
*':#)10*'#&5%4'9
౐ⷺ㩘㩨㩣㩎ో㩒㩆㩨
౐ⷺ㩏㨹㩎㩆㨷
*':#)10#.076
(.#69#5*'4
㩚㩀㩨㩁㩙㩣ᐔᐳ㊄
524+0)9#5*'4
9#8')7+&'%.#/2
+057.#614
౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
524+0)9#5*'4
&'5%4+26+10%1&'ͳ
45$
36;
14+0)
176.+0'
9)%.#/2
ዉᵄ▤㑆ᐳ
(''&'49$#55'/$.;
㨻㩧㩍㩏Ꮏ᧚
0#/'
ዉᵄ▤᛼ߐ߃'ဳ
:0#
㩖㨲㨺㩎㩨9)
㩔㩨㩒ᐳ㊄
36;
70+6
㨻㩧㩍㩏
%4+/210.7)
࿶⌕┵ሶ
%4+/210.7)
࿶⌕┵ሶ
6'4/+0#.12'0'4
ᠲ૞㩤㩔㩨㨺
#06+%14415+1047$$'4
㒐ⲁࠧࡓ
㩆㨺㩣㩦㨹㩆㨶㨺
5'#.9#5*'4
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
⇟ภ
01
Ꮏ੐᧚ᢱ⴫
A-3
0#/'
࡙࠾࠶࠻
$': :0#
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
%1&'01
/575
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
%1&'01
(8
.(
%1&'01
(8
%1&'01
%1&'01
%1&'01
41*5
41*5
%1&'01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
):: A-4
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
41*5
/:575
/:575
/:575
/:575
/575
*':076
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
/575
(.#69#5*'4
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ㪆䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
ဳᑼ䎒䱤䱚䱮䲈⇟ภ䬛䯾Ბ䬽႐ว䫺ਅᲑ䭗䭙਄Ბ䬺ઍ䭞䭚ㆊᷰᦼຠ䬶䬑䭙䫺䬸䬰䭘䬚䬛౉䬲䬵䬓䭍䬨䫻䫹䬹䬙䫺ຠ⾰䬾ᄌ䭞䭙䭍䬪䭢䫻
䯴⇛࿑䬽ኸᴺ䬾䫺ෳ⠨୯䬶䬨䫻䎃䎧䎬䎰䎨䎱䎶䎬䎲䎱䎶䎃䎬䎱䎃䎧䎵䎤䎺䎬䎱䎪䎃䎩䎲䎵䎃䎵䎨䎩䎨䎵䎨䎱䎦䎨䎃䎲䎱䎯䎼䎑䯵
䎷䎺䎲䎃䎷䎼䎳䎨䎶䎃䎤䎱䎧䎃䎦䎲䎧䎨䎶䎃䎰䎤䎼䎃䎥䎨䎃䎯䎬䎶䎷䎨䎧䎃䎩䎲䎵䎃䎤䎱䎃䎬䎷䎨䎰䎑䎃䎃䎷䎫䎨䎃䎯䎲䎺䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎃䎰䎤䎼䎃䎥䎨䎃䎶䎫䎬䎳䎳䎨䎧䎃䎬䎱䎃䎳䎯䎤䎦䎨䎃䎲䎩䎃
䎷䎫䎨䎃䎸䎳䎳䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎑䎃䎴䎸䎤䎯䎬䎷䎼䎃䎬䎶䎃䎷䎫䎨䎃䎶䎤䎰䎨䎑
$':
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
⇟ภ
01
%14'%#$.'
㩃㨺㩖㩨㩣
%
%14'%#$.'
㩃㨺㩖㩨㩣
%
%14'%#$.'
㩃㨺㩖㩨㩣
%
%14'%#$.'
㩃㨺㩖㩨㩣
%
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
49/
%1&'01
49/
%1&'01
49/
%1&'01
49/
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
‫ޓޓޓޓޓޓޓޓޓޓ‬
ାภ㩃㨺㩖㩨㩣‫ޓޓޓޓ‬
5+)0#.%#$.'
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)::
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
%1&'01 49
49
%1&'01
/:575
%1&'01
/575
%1&'01
/575
ဳฬ㧛ⷙᩰ
&'5%4+26+105
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
⇛‫ޓޓ‬࿑
176.+0'
(#4(%4
).: ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
*':#)10#.*'#&$1.6
౐ⷺ㩘㩨㩣㩎
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
ฬ‫ޓޓ‬⒓
0#/'
%1&'01
6;2'
A-6
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
+056#..#6+10/#6'4+#.5
):: Ꮏ੐᧚ᢱ⴫
%2
6;2'
Ꮏ੐᧚ᢱ⴫
%1&'01
A-5
%#4$10$475*
㩀㨺㩘㩨㩧㩖㩨㩡㩆
6#$
&9)01
14
6;2'01
2'4
8'5
5'652'4
8'55'.
$1:012
&<: ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪ
ᄌࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
4'/#4-5%1&'01
&<:
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
&9)01
2'4
5'6
914-+0)
37#06+6;
52#4'
52
75'
6;2'
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
%1&'01
A-7
0#/'
176.+0'
+056#..#6+10/#6'4+#.5
#%%'5514+'5
52#4'2#465
52#4'2#465
70+6
&8+&&5+0).'.+0-/
(2
52
52
/7%45*-#6
&'5%4+26+10%1&'ͳ
A-8
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
#%↪
&%↪
).: ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㪉㪅੍஻ຠ䈲䇮㪘㪚↪㪃㪛㪚↪䈪ㆬᛯ㗿䈇䉁䈜䇯
㪚㪟㪦㪦㪪㪜㩷㪪㪧㪘㪩㪜㩷㪧㪘㪩㪫㪪㩷㪛㪜㪧㪜㪥㪛㪠㪥㪞㩷㪦㪥㩷㪘㪚㩷㪦㪩㩷㪛㪚㩷㪧㪦㪮㪜㪩㪅
㪈㪅䍘䍎䍢䍼ᧃየ䈮㪲㪁㪁㪴䈱ઃ䈇䈢䍳䍤䍍䍢䈲ઍ⴫䈱ဳᑼ㪆䍘䍎䍢䍼䉕⴫␜䈚䈩䈇䉁䈜䇯
㪛㪦㪬㪙㪣㪜㩷㪘㪪㪫㪜㪩㪠㪪㪢㩷㪛㪜㪥㪦㪫㪜㪪㩷㪚㪦㪤㪤㪦㪥㪣㪰㩷㪬㪪㪜㪛㩷㪜㪨㪬㪠㪧㪤㪜㪥㪫㪅
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
Ꮏ੐᧚ᢱ
#%%'5514+'5
ઃዻຠ
ઃዻຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
&+52.#;70+6
⴫␜ㇱ
࡙࠾࠶࠻
/7%4
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
5'.(6#22+0)5%4'9
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬㩆㨷
2#0'.*11-
㩔㩩㩒㩣㩖㨹㩂
2#0'.%18'4
㩔㩩㩒㩣㩀㩔㩨㨺
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
:575
%1&'01 41*5
%1&'01
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
6;2'
ᢙ㊂
36;
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6
⴫␜ㇱ↪‫ޓޓޓޓޓ‬
‫(ޓ‬14&+52.#;70+6
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
#%%'5514+'5
ઃዻຠ⴫
%1&'01
A-9
FUSE
ヒューズ
ELECTRIC
CO.,LTD.
FGMB 2A 250V
FGMB 250V 2A
PBF
DWG. NO.
OR
TYPE NO.
S
DWG NO.
PER
VES
2
SPARE
SETS PER
VESSEL
P
000-157-497-10
000-122-000-00
表示部用
FOR DISPLAY UNIT
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は
変わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
1/1
03GL-X-9303 -1 1/1
BOX NO.
REMARKS/CODE NO.
03GL-X-9303
QUANTITY
E
WORKING
PER
SET
U
SP03-14401
008-535-990
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
FURUNO
OUTLINE
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
TYPE
CODE NO.
A-10
&1%7/'06
+056#..#6+10/#6'4+#.5
52#4'2#465
70+6
176.+0'
15
+/
1/
1/
%2
%2
52
52
52
427
36;
A-11
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
㪉㪅䋨㪁㪈䋩䋨㪁㪉䋩䈲䇮䈠䉏䈡䉏઀᭽ㆬᛯຠ䉕⴫䈚䉁䈜䇯
䋨㪁㪈䋩䋨㪁㪉䋩㪠㪥㪛㪠㪚㪘㪫㪜㩷㪪㪧㪜㪚㪠㪝㪠㪚㪘㪫㪠㪦㪥㩷㪪㪜㪣㪜㪚㪫㪠㪭㪜㩷㪠㪫㪜㪤㪅
㪊㪅㩿㪁㪊㪀㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪઀᭽䈱ᤨ䈱䉂ᷝઃ䈘䉏䉁䈜䇯
㪪㪬㪧㪧㪣㪰㪜㪛㩷㪮㪠㪫㪟㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪㩷㪦㪥㪣㪰㪅
).: &'5%4+26+10%1&'ͳ
㪈㪅䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
12'4#6145)7+&'
ᠲ૞ⷐ㗔ᦠ
+056#..#6+10/#07#.
ⵝ஻ⷐ㗔ᦠ
12'4#6145/#07#.
ขᛒ⺑᣿ᦠ
12'4#6145/#07#.
ขᛒ⺑᣿ᦠ
࿑ᦠ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
52#4'2#465
੍஻ຠ
52#4'2#465
੍஻ຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
241%'551470+6
೙ᓮㇱ
࡙࠾࠶࠻
0#/'
427
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
CRIMP-ON LUG
圧着端子
TERMINAL OPENER
操作レバー
TERMINAL OPENER
操作レバー
名 称
NAME
略 図
OUTLINE
CODE
NO.
FV2-4
CODE
NO.
734-230
CODE
NO.
231-131
000-157-247-10
000-147-417-10
000-165-800-10
型名/規格
DESCRIPTIONS
2
1
1
数量
Q'TY
1/1
制御部用 FOR PROCESSOR
UNIT
制御部用 FOR PROCESSOR
UNIT
制御部用 FOR PROCESSOR
UNIT
用途/備考
REMARKS
03GL-X-9405 -2
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9405
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
3
2
1
番 号
NO.
INSTALLATION MATERIALS
工事材料表
CP03-25602
TYPE
AC用
008-535-940-00
CODE NO.
A-12
ヒューズ
FUSE
PER
VES
000-155-826-10
1/1
AC100用 FOR PROCESSOR UNIT
03GL-X-9305
4
SPARE
FUSE
ヒューズ
FURUNO
ELECTRIC
OUTLINE
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
CO.,LTD.
FGBO 250V 5A
PBF
DWG. NO.
OR
TYPE NO.
S
DWG NO.
PER
VES
4
SPARE
P
SETS PER
VESSEL
000-155-840-10
FOR PROCESSOR UNIT
1/1
AC220用 REMARKS/CODE NO.
03GL-X-9306
QUANTITY
E
WORKING
PER
SET
U
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変
わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
DWG NO.
PER
SET
REMARKS/CODE NO.
SETS PER
VESSEL
03GL-X-9306 -1 1/1
BOX NO.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
CO.,LTD.
QUANTITY
E
WORKING
S
SP03-14405
008-535-920-00
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は
変わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
ELECTRIC
FGBO 125V
10A PBF
DWG. NO.
OR
TYPE NO.
U
TYPE
CODE NO.
A-14
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
FURUNO
OUTLINE
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
SP03-14404
TYPE
P
03GL-X-9305 -1 1/1
BOX NO.
008-535-910
CODE NO.
A-13
INSTALLATION MATERIALS
SPARE PARTS
UNIT
O U T L I N E
008-572-750-00
CP03-31401
008-572-740-00
SP03-15502
008-572-730-00
SP03-15501
000-090-665-00
PSU-006-*-*
DESCRIPTION/CODE №
**
03GX-X-9852 -0
Q'TY
1
(*1)
1
(*1)
1
1
A-15
1/1
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GX-X-9852
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
型式/ コー ド番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
(*1)の予備品は,仕様によりAC100用:SP03-15501,AC220用:SP03-15502.
* 1 : SELECT ONE ACCORDING TO PROCESSOR UNIT'S SPECIFICATIONS : SP03- 15501 FOR 100VAC OR SP03- 15502 FOR 220VAC
INSTALLATION MATERIALS
工事材料
工事材料
SPARE PARTS
予備品
SPARE PARTS
予備品
予備品
POWER CONTROL UNIT
電源制御部
ユニット
N A M E
PSU-006
PACKING LIST
CRIMP-ON LUG
圧着端子
名 称
NAME
略 図
OUTLINE
CODE
NO.
FV2-4
000-157-247-10
型名/規格
DESCRIPTIONS
CP03-31401
TYPE
14
数量
Q'TY
用途/備考
REMARKS
03GX-X-9402 -1
1/1
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GX-X-9402
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
1
番 号
NO.
INSTALLATION MATERIALS
工事材料表
008-572-750-00
CODE NO.
A-16
PSU-006
FUSE
ヒューズ
PER
VES
000-155-840-10
03GX-X-9301
2
SPARE
1/1
PSU-006
FUSE
ヒューズ
FURUNO
ELECTRIC
OUTLINE
POWER CONTROL UNIT
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
CO.,LTD.
FGBO 250V 3A
PBF
DWG. NO.
OR
TYPE NO.
AC220V
S
DWG NO.
PER
VES
2
SPARE
SETS PER
VESSEL
P
000-155-841-10
1/1
03GX-X-9302 -0 1/1
BOX NO.
REMARKS/CODE NO.
03GX-X-9302
QUANTITY
E
WORKING
PER
SET
U
SP03-15502
008-572-740-00
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変
わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
DWG NO.
PER
SET
REMARKS/CODE NO.
SETS PER
VESSEL
TYPE
CODE NO.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
CO.,LTD.
QUANTITY
E
WORKING
S
P
03GX-X-9301 -0 1/1
BOX NO.
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変
わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
ELECTRIC
FGBO 250V 5A
PBF
DWG. NO.
OR
TYPE NO.
AC100V
U
SP03-15501
TYPE
A-18
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
FURUNO
OUTLINE
POWER CONTROL UNIT
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
008-572-730-00
CODE NO.
A-17
WASHER HEAD SDREW *B*
+-ナベセムスB
名 称
NAME
CODE
NO.
000-163-192-10
M4X12 C2700W MBNI2
4
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9411
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
1
番 号
NO.
CUSHION
クリアバンポン
WASHER HEAD SDREW *B*
+-ナベセムスB
GROMMET
グロメット
KB FIXING METAL
KB直付金具
名 称
NAME
略 図
OUTLINE
型名/規格
DESCRIPTIONS
FP03-09850
008-535-610-00
000-166-401-10
100-306-251-10
000-163-192-10
CODE
NO.
000-166-468-10
TM-180-302
CODE
NO.
M4X12 C2700W MBNI2
CODE
NO.
G-39
CODE
NO.
03-163-7521-1 ROHS
TYPE
CODE NO.
3
2
1
1
数量
Q'TY
1/1
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
用途/備考
REMARKS
03GL-X-9505 -7
A-20
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9505
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
4
3
2
1
番 号
NO.
ACCESSORIES
用途/備考
REMARKS
1/1
INSTALLATION MATERIALS
数量
Q'TY
03GL-X-9411 -1
付属品表
型名/規格
DESCRIPTIONS
CP03-25604
TYPE
工事材料表
略 図
OUTLINE
008-539-850-00
CODE NO.
A-19
数量
Q'TY
用途/備考
REMARKS
RUBBER FOOT
クリアバンポン
WASHER HEAD SDREW *B*
+-ナベセムスB
GROMMET
グロメット
BLIND SEAL
ブラインドシール
KEYBOARD FIXTURE
KB直付金具(T)
100-306-291-10
000-166-406-10
100-173-591-10
000-163-192-10
CODE
NO.
000-166-468-10
TM-180-302
CODE
NO.
M4X12 C2700W MBNI2
CODE
NO.
G-49
CODE
NO.
22-020-1005-1 ROHS
CODE
NO.
03-163-7821-1 ROHS
2
2
1
3
1
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
操作部用
FOR CONTROL UNIT
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9506
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
5
4
3
2
1
WING SCREW
蝶ボルト
HEX.NUT
六角ナット 1種
WASHER HEAD SDREW *B*
+-ナベセムスB
FLUSH MOUNTING PLATE
フラッシュマウント金具
名 称
NAME
略 図
OUTLINE
型名/規格
DESCRIPTIONS
FP03-09870
008-535-630-00
100-306-261-10
000-163-192-10
000-165-921-10
CODE
NO.
000-162-682-10
M5X40 SUS304
CODE
NO.
M5 SUS304
CODE
NO.
M4X12 C2700W MBNI2
CODE
NO.
03-163-7531-1 ROHS
TYPE
CODE NO.
4
4
4
4
数量
Q'TY
用途/備考
REMARKS
03GL-X-9503 -6
A-22
1/1
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9503
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
4
3
2
1
番 号
NO.
ACCESSORIES
名 称
NAME
型名/規格
DESCRIPTIONS
1/1
ACCESSORIES
番 号
NO.
略 図
OUTLINE
03GL-X-9506 -7
付属品表
FP03-09860
TYPE
付属品表
008-535-690-00
CODE NO.
A-21
*':$1.6
5.166'&9#5*'4*'#&
౐ⷺ㩇㩢㩦㩢㩈㩛㩇$
*':$1.6
౐ⷺ㩇㩢㩦㩢‫ޓ‬㩘㩨㩣㩎
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
50#2$76610
㩇㩏㨹㩖㩩㩘㩨㩊㩧
*1.'2.7)
㩘㨺㩣㩖㩩㩡㩂㩨
*#0)'456#;
㩔㩧㩀㩨㨺㩅㩅㨾
*#0)'44
㩔㩧㩀㩨㨺4
*#0)'4.
㩔㩧㩀㩨㨺.
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
/:575
%1&'01
/:575
%1&'01
/575‫ޓ‬
%1&'01
/575
%1&'01
-$㩠㨽‫ޓ‬㩘㩨㩊㩧㩂㩥
%1&'01
%2*2
%1&'01
41*5
%1&'01 %1&'01 41*5
41*5
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
ฬ‫ޓޓ‬⒓
0#/'
9#8'9#5*'4
ᵄᐳ㊄
18#.*'#&5%4'9
ਣ⋁ዊ㩒㩆㩨
415'66'9#5*'4
㩥㨺㩈㩨㨹㩎ᐳ㊄
*#0&.'
ขᚻ
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
%1&'
01
99575
%1&'
01
/:%9㩘㩩㩢㩆㨺㩣
%1&'
01
/%9㩘㩩㩢㩆㨺㩣
/%9㩘㩩㩢㩆㨺㩣
%1&'
01
41*5
6;2'
%1&'01
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
).: A-24
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
).:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
#%%'5514+'5
⇟ภ
01
#%%'5514+'5
).: ઃዻຠ⴫
(2
6;2'
ઃዻຠ⴫
%1&'01
A-23
OTHER INSTALLATION MATERIALS
INSTALLATION MATERIALS
UNIT
O U T L I N E
000-156-054-11
MJ-A3SPF0015-100C
000-164-637-10
000-147-510-00
P5E-4PTX-BL
P5E-4PTX-BL
008-544-400-00
CP03-27431
000-081-569-00
CU-200
DESCRIPTION/CODE №
03GO-X-9855 -4
Q'TY
1
1
1
1
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GO-X-9855
A-25
1/1
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
型式/ コー ド番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
CABLE ASSY.
ケーブル組品MJ
CABLE ASSY.
ケーブル組品
その他工材
INSTALLATION MATERIALS
工事材料
工事材料
MEMORY CARD INTERFACE
メモリーカードインターフェイス
ユニット
N A M E
CU-200-FAR
PACKING LIST
.#$'.#66#%*+0)
241%'&74'
⥽ベ㩙㨺㩂⾍ઃⷐ㗔
6*4'#&'&41&
ኸಾ㩘㩨㩣㩎
*':076
౐ⷺ㩏㨹㩎㩆㨷
(.#69#5*'4
㩚㩀㩨㩁ਣᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
56''4+0)9*''..#$'.
⥽ベ⾍ࠅ㩙㨺㩂
$5*
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'
01
%㩦㨾㨼
%1&'
01
/:575
%1&'
01
/575
%1&'
01
/575
%1&'
01
/575
%1&'
01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
ᢙ㊂
36;
↪ㅜ㧛஻⠨
4'/#4-5
)1: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)1:
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖ
ࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4
241&7%637#.+6;+56*'5#/'
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
6;2'
%1&'01
A-26
A-28
PACKING LIST
NAME
OUTLINE
予備品
03GL-X-9852 -4
GC-10-2
DESCRIPTION/CODE №
Q'TY
SPARE PARTS
予備品
1
SP03-13300
SPARE PARTS
OTHER PARTS
OUTLINE
DESCRIPTION/CODE №
Q'TY
5
M3X8 C2700W MBNI2
WASHER HEAD SCREW
000-163-190-10
+ナベセムスA
008-419-280-00
その他部品
NAME
+-ナベセムスB
1/1
2
M2.6X10 C2700W MBNI2
WASHER HEAD SCREW
GCカバー組品
1
80-0665
000-163-477-10
コネクタ(231)
GC COVER ASSY.
008-537-030-00
NHコネクタ
1
03-2091(5P)
000-147-414-11
コネクタ(231)
NH CONNECTOR ASSY.
008-534-670-00
VHコネクタ
1
231-607/019-FUR
CONNECTOR
1
231-107/026-FUR
CONNECTOR
1
03-2090(3P)
000-147-413-11
VH CONNECTOR ASSY.
008-534-660-00
VHコネクタ
1
03-2089(5P)
VH CONNECTOR ASSY.
008-534-650-00
XH-PHコネクタ
03-2088(6-14P)
1
XH-PH CONNECTOR ASSY.
008-534-640-00
演算プリント
1
64P1106A(LF)
PROCESSOR BOARD
004-655-920-00
+-ナベセムスB
M4X8 C2700W MBNI2
3
WASHER HEAD SCREW(B)
000-163-200-10
型式/コー ド番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
03GO-X-9502
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
000-163-167-10
4
M4X10 C2700W MBNI2
WASHER HEAD SCREW
3
+-ナベセムスA
SELF-TAPPING SCREW
2
+トラスタッピンネジ 1シュ
ハンガー
MOUNTING BRACKET
1
CODE
NO.
000-162-608-10
5X20 SUS304
CODE
NO.
100-316-250-10
1
CODE
NO.
19-023-3081-0
4
用途/備考
REMARKS
型名/規格
DESCRIPTIONS
略 図
OUTLINE
名 称
NAME
番 号
NO.
FP03-10201
TYPE
For CU-200 Desktop mount kit
ACCESSORIES
付属品表
008-539-530-00
CODE NO.
数量
Q'TY
Option
03GO-X-9502 -3
1/1
A-27
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
03GL-X-9852
(略図の寸法は、参考値です。DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
FUSE
ヒューズ
ELECTRIC
CO.,LTD.
FGMB 2A 250V
FGMB 250V 2A
PBF
DWG. NO.
OR
TYPE NO.
GC-10
S
DWG NO.
PER
VES
8
SPARE
SETS PER
VESSEL
P
000-157-497-10
000-122-000-00
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変
わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE
UPPER PRODUCT. QUALITY IS THE SAME.
1/1
03GL-X-9302 -2 1/1
BOX NO.
REMARKS/CODE NO.
03GL-X-9302
QUANTITY
E
WORKING
PER
SET
U
SP03-13300
TYPE
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
FURUNO
OUTLINE
SPARE PARTS LIST FOR
NAME OF
PART
MFR'S NAME
1
ITEM
NO.
SHIP NO.
008-419-280-00
CODE NO.
A-29
COUPLING PLATE ASSY.
連結台(20)組品
WASHER HEAD SDREW *B*
+-ナベセムスB
名 称
NAME
略 図
OUTLINE
型名/規格
DESCRIPTIONS
000-163-192-10
CODE
NO.
008-536-980-00
OP03-183-1
CODE
NO.
M4X12 C2700W MBNI2
Coupling pedestal kit
RCU-014 + MU-201CR
1
4
数量
Q'TY
OP03-183
TYPE
用途/備考
REMARKS
Option
03GL-X-9408 -6
1/1
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9408
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
2
1
番 号
NO.
INSTALLATION MATERIALS
工事材料表
008-535-640-00
CODE NO.
A-30
16*'42#465
176.+0'
/%9/$0+
/‫ޓ‬%9/$0+
53
&8+&&5.+0-/
2
2
2
2$
.(
5.$(40#
/:%9/$0+
&'5%4+26+10%1&'ͳ
A-31
).: 36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
524+0)9#5*'4
㩔㩨㩒㩅㩨㩀㩨㩒
52#%'4
㩇㩗㩩㨺㩅㨺
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
:*%100'%614
:*㩄㩒㩂㩊
:*%100'%614
:*㩄㩒㩂㩊
8*%100'%614
8*㩄㩒㩂㩊
4)$$7(($1#4&
4)$$7((㩖㩩㩢㩧㩎
&8+4)$#55;
&8+4)$⚵ຠ
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇$
0#/'
ߘߩઁㇱຠ
12
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
MODULAR CONNCTOR
コネクタ(モジュラー)
名 称
NAME
略 図
OUTLINE
For LAN cable kit
CODE
NO.
MPS588-C
000-166-044-10
型名/規格
DESCRIPTIONS
2
数量
Q'TY
CP03-28901
TYPE
用途/備考
REMARKS
Option
03GL-X-9407 -4
1/1
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9407
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりませ
ん。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER
PRODUCT. QUALITY IS THE SAME.
1
番 号
NO.
INSTALLATION MATERIALS
工事材料表
008-542-460-00
CODE NO.
A-32
D-1
D-2
D-3
May 17'07 R.Esumi
1/Sep/2010
Y.NISHIYAMA
D-4
Y. Hatai
Takahashi T.
D-5
Jan.18'08 R.Esumi
D-6
Apr.23'07 R.Esumi
D-7
Apr.23'07 R.Esumi
D-8
Apr.23'07 R.Esumi
D-9
Apr.23'07 R.Esumi
D-10
Apr.23'07 R.Esumi
D-11
D-12
D-13
D-14
Y. Hatai
D-15
Y. Hatai
D-16
Y. Hatai
D-17
Y. Hatai
D-18
Apr.05'04
D-19
注記
*1)造船所手配。
*2)オプション。
*3)最長 100m (延長するときは接続箱RJB-001が必要 )。
*4)保護アース用ケーブルは緑/黄の絶縁線を使用のこと。
*5)FAR-2157-BBのときは支給なし。
*6)交流は両極切りブレーカ(造船所手配)を経由すること。
トランス
TRANSFORMER
RU-1803 *2
保護アース
PE *1 *4
IV-8sq.
DPYC-2.5
*1
1
2
3
NOTES
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: MAX. 100m. (JUNCTION BOX RJB-001 IS REQUIRED FOR EXTENSION)
*4: USE GRN/YEL VINYL INSULATION WIRE FOR PROTECTIVE EARTH.
*5: NOT SUPPLIED FOR FAR-2157-BB.
*6: PASS THE AC LINE THROUGH A DOUBLE-CONTACT BREAKER (SHIPYARD SUPPLY).
表示部
MONITOR UNIT
MU-201CR *5
保護アース
PE
*1 *4
IV-8sq.
DRAWN
Feb. 1 '07
CHECKED
APPROVED
SCALE
DWG.No.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Maki
TAKAHASHI.T
MASS
kg
C3522-C01- C
1
2
3
TXP
TXN
RXP
NC
NC
RXN
NC
NC
防水型カードインターフェイス
MEMORY CARD I/F UNIT
CU-200
*2
AC
AC
GND
P
P
*1
IV-1.25sq.
TYPE
名 称
Y.Hatai
NAME
NR203PF-VVS1.25
3.5m, φ8.6
MPS588-C
100-230VAC
1φ,50/60Hz
*1
LAN CABLE(CAT5) OR
FR-FTPC-CY,10/20/30m,φ13
シロ/ミドリ WHT/GRN
ミドリ
GRN
シロ/ダイ WHT/ORG
アオ
BLU
シロ/アオ WHT/BLU
ダイ
ORG
シロ/チャ WHT/BRN
チャ
BRN
P5E-4PTX-BL,10m,φ6.3
1
2
3
4
5
6
7
8
TXP
TXN
RXP
NC
NC
RXN
NC
NC
NETWORK
J611
AIS_TD-A 1
AIS_TD-B 2
AIS_RD-A 3
AIS_RD-B 4
AIS_GND 5
P
P
P
P
P
P
P
P
P
RW-4864,φ9.5
RW-4864,φ9.5
RW-4864,φ9.5
*1
TTYCS-7
*1
TTYCS-4
*1
TTYCS-4
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
SUB DISPLAY2
(SEMI-LOG)
SUB DISPLAY1
(FULL-LOG)
MASTER RADAR
ALARM SYSTEM
AIS
(IEC-61162-2)
TRACK_CONTROL
(IEC-61162-1)
ECDIS
(IEC-61162-1)
SPEED LOG
(IEC-61162-1)
NAVIGATOR
(IEC-61162-1)
HDG SENSOR
(IEC-61162-2)
PC
5
J618(NH)
GND 1
OP_HD_2 2
GND 3
OP_BP_2 4
GND 5
OP_TRIG_2 6
GND 7
OP_VIDEO_2 8
J617(NH)
GND 1
OP_HD_1 2
GND 3
OP_BP_1 4
GND 5
OP_TRIG_1 6
GND 7
OP_VIDEO_1 8
J616(NH)
GND 1
OP_HD_IN 2
GND 3
OP_BP_IN 4
GND 5
OP_TRIG_IN 6
GND 7
OP_VIDEO_IN 8
J612
ALARM1_0 1
ALARM1_1 2
ALARM2_0 3
ALARM2_1 4
ALARM3_0 5
ALARM3_1 6
OPERATOR_FITNESS_0 7
OPERATOR_FITNESS_1 8
EXT_ALM_ACK_N 9
GND 10
SYS_FAIL-H 11
SYS_FAIL-C 12
J614
1 +12V
2 GND
P
J619
ARPA-A 1
ARPA-B 2
NC 3
P
P
J607
LOG-A 1
LOG-B 2
NC 3
J620
TRK_TD-A 1
TRK_TD-B 2
TRK_RD-A 3
TRK_RD-B 4
GND 5
P
J606
NAV-A 1
NAV-B 2
NC 3
*1
TTYCS-1Q
*1
4
P
P
MPS588-C
DVI-D/DSINGLELINK5M/10M
5/10m,φ7
MJ-A3SPF0015,10m,φ6
制御部
PROCESSOR UNIT
RPU-013
J302
TXP
TXN
RXP
NC
NC
RXN
NC
NC
RGBビデオコンバータ
RGB VIDEO CONVERTER
DVI-RGB-1 *2
P
RS-232C
J605
HDG-A 1
HDG-B 2
HDG_GND 3
RS-232C CABLE
J501
KEY_TXD-B
KEY_TXD-A
KEY_RXD-B
KEY_RXD-A
PWR_SW
GND
+12V
GND
NC
NC
24VDC
MJ-A3SPF
J1
シロ WHT
+12V 1
2
クロ BLK
GND
FG 3
1
2
3
4
5
6
7
8
9
J601
NC
RXD
TXD
NC
GND
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
22
24
1
2
J622
SYS_ACK-H
SYS_ACK-C
1
2
3
4
5
6
7
8
9
10
RSB-107
SAME AS AVOBE
J615
+12V
GND
+5V
GND
-12V
J502/J522
KEY_TXD-B
KEY_TXD-A
KEY_RXD-B
KEY_RXD-A
PWR_SW
GND
+12V
GND
NC
NC
*2
XH10P-W-5P-A
10/20/30m,φ9
200VAC,3φ,50Hz
220VAC,3φ,60Hz
DVI-D MONITOR
J205
1
2
3
4
5
J501/J521
1 KEY_TXD-B
2 KEY_TXD-A
3 KEY_RXD-B
4 KEY_RXD-A
5 PWR_SW
6 GND
7 +12V
8 GND
9 SYS_FAIL-H
10 SYS_FAIL-C
J507/J527
1 SYS_FAIL-H
2 SYS_FAIL-C
3 SYS_ACK-H
4 SYS_ACK-C
TOTAL: UP TO 31.5m
SPU_RF_D-A
SPU_RF_D-B
RF_SPU_D-A
RF_SPU_D-B
SG
GND
TB802
IF_VIDEO
GND
18
22
1
2
BRN
RED
ORG
YEL
GRN
J602
KEY_TXD-B 1
KEY_TXD-A 2
KEY_RXD-B 3
KEY_RXD-A 4
PWR_SW 5
GND 6
+12V 7
GND 8
SYS_FAIL-H 9
SYS_FAIL-C 10
合計:31.5m以下
XH10P-W-6P
10m (20/30m OPTION),φ9
3
4
5
6
7
8
RSB-106
*2
DVI CABLE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
DVI-D MONITOR
J204
DVI0TX2_N
DVI0TX2_P
A_GND
NC
NC
NC
NC
NC
DVI0TX1_N
DVI0TX1_P
A_GND
NC
NC
VCC
GND
NC
DVI0TXD_N
DVI0TXD_P
A_GND
NC
NC
A_GND
DVI0TXC_P
DVI0TXC_N
チャ
アカ
ダイ
キ
ミドリ
23
24
1
2
RED
GRN
BLK
WHT
GRN[B]
RED[B]
3
外部モニター
EXT. MONITOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
J3
アカ
ミドリ
クロ
シロ
ミドリ(太)
アカ(太)
操作部
CONTROL UNIT
RCU-014/015
TMDS_DATA2(-)
TMDS_DATA2(+)
TMDS_DATA2/4_SHIELD
NC
NC
DDC_CLOCK
DDC_DATA
NC
TMDS_DATA(-)
TMDS_DATA(+)
TMDS_DATA1/3_SHIELD
NC
NC
+5V_POWER
GND
HOT_PLUG_DETECT
TMDS_DATAB(-)
TMDS_DATAB(+)
TMDS_DATA0/5_SHIELD
NC
NC
TMDS_CLOCK_SHIELD
TMDS_CLOCK(+)
TMDS_CLOCK(-)
J3
J9
R
GND
G
GND
B
GND
HS
GND
VS
GND
1
2
3
4
TB801
1 24V_PLUS
2 24V_MINUS
6 TX_HV
8 TX_SIG
9 GND
TB901
1 U/24V+
2 V/24V3 W
操作部
CONTROL UNIT
RCU-016 *2
TB1
1 H
2 C
5
6
7
8
9
10
3
4
1
2
P
P
ダイ(太) ORG[B]
キ(太)
YEL[B]
*3
RW-9600,15/30/40/50m,φ22
*1
TPYCY-1.5,MAX.100m
*1
TPYCY-2.5,MAX.100m
2
100-230VAC
1φ,50-60Hz
*6
TB1
1 H
2 C
J3
VCC
GND
-5/-12V
DPYC-2.5 *1
1
2
3
4
5
6
7
8
9
10
11
12
13
J4
+12V
+12V
GND
GND
NC
NC
*6
J1
03-2091(5P)
チャ BRN
アカ RED
ダイ ORG
キ
YEL
J603(XH)
GC_LED
GC_HOLD
GC_UP
J610
GC_DOWN
24V_PLUS 1
GC_0V
24V_MINUS 2
GC_5V
MOTOR(+) 3
J608
MOTOR(+) 4
AD_DATA-H MOTOR(-) 5
AD_DATA-C MOTOR(-) 6
AD_CLK-H SPU_RF_D-A 7
AD_CLK-C SPU_RF_D-B 8
RF_SPU_D-A 9
RF_SPU_D-B 10
SG 11
GND 12
J609
IF_VIDEO
GND
TB BOARD
03P9342
100-120/
200-230VAC
1φ,50-60Hz
BNCコネクタコンバータ
BNC CONNECTOR
CONVERTER
DSUB-BNC-1 *2
DPYC-1.5 *1
R_VIDEO
GND
G_VIDEO
GND
B_VIDEO
GND
H_SYNC
GND
V_SYNC
GND
VCC
GND
-5/-12V
RGB バッファ 基板
RGB BUFFER PCB
03P9229A
*6
J2
R_VIDEO
G_VIDEO
B_VIDEO
NC
NC
GND
GND
GND
NC
GND
GND
NC
H_SYNC
Y_SYNC
NC
1
2
3
4
5
DVI-RGB変換基板
DVI-RGB CONVERSION BOARD
SLB-FRN4-A
440VAC
1φ,50-60Hz
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
J7(NH)
DATA1-H
DATA1-C
SHIFT1-H
SHIFT1-C
FG
03-2088(6-14P) 1
2
3
4
5
6
J604
1 +12V
2 ANT_ON_N
J621
6 GND
*1
COAX.(75Ω)x5
*1
BRN
RED
ORG
1
YEL
2
GRN
3
BLU
4
PPL
5
03-2089(5P)
9
10
11
12
13
14
アカ RED
シロ WHT
クロ BLK
TX_HV 6
TX_SIG 8
GND 9
*1
TPYC-1.5,MAX.100m
アカ RED
シロ WHT
クロ BLK
TB3
24V+/U 1
24V-/V 2
W 3
RW-4747
VDR
VGA CABLE
*1
J680
チャ
アカ
ダイ
キ
ミドリ
アオ
ムラサキ
GYRO CONVERTER
BOARD
64P1106A *2
RGB EXT. MONITOR
保護アース
*1 *4
PE
IV-8sq.
TTYCS-4
1
2
3
4
5
6
7
1
2
3
J5(VH)
GYRO_R2
GYRO_R1
NC
J4(VH)
GYRO_S1
GYRO_S2
GYRO_S3
GYRO_T
GYRO_FG
J1
RU-5466-1 *2
保護アース
PE
*1 *4
IV-8sq.
03-2090(3P)
TPYC-2.5 *1
RU-6522 *2
RED
WHT
BLK
*1
*6
440VAC,3φ,50Hz
TPYC-2.5 *1
TB3
MPYC-7
*6
電源制御部 +12V 11
POWER UNIT ANT_ON 12
GND 13
PSU-006
1 U/24V+
2 V/24V3 W
TB1
1
2
TB2
A
220VAC,3φ,50Hz
RU-5693 *2
RU-3423 *2
RU-1803 *2
空中線部
ANTENNA UNIT
RSB-106/107
A-D CONVERTER
GYROCOMPASS
*1
DPYC-2.5 *1
*6
24VDC
*6 or
200VAC,3φ,50Hz
TPYC-2.5 *1
220VAC,3φ,60Hz
*6
TPYC-2.5 *1
110VAC,3φ,60Hz
DPYC-4
DPYC-2.5 *1
100-115/220-230VAC,1φ,50/60Hz
DPYC-2.5 *1
B
100/110/115/220/230VAC,1φ,50/60Hz
D
*6
C
*6
440VAC,1φ,50-60Hz
1
6
S-1
空中線型式 回転数 電源
ANT. TYPE
RPM
POWER SUPPLY
LAN
スイッチング ハブ
*2
SWITCHING HUB
HUB-100 (8 PORTS)
保護アース PE
IV-1.25sq. *1 *4
FAR-2157/2157-BB
船舶用レーダー/ARPA
相互結線図
MARINE RADAR/ARPA
INTERCONNECTION DIAGRAM
Download PDF

advertising