Service manual | Furuno FAR2167DS-BB Radar Detector User Manual

MARINE RADAR/ARPA
FAR2167DS-BB
PRINTED IN JAPAN
SAFETY INSTRUCTIONS
The installer must read and follow all the safety instructions before attempting to install the
equipment.
WARNING
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
Warning, Caution
Prohibitive Action
Mandatory Action
WARNING
Radio Frequency Radiation Hazard
The radar antenna emits electromagnetic radio frequency (RF) energy which can
be harmful, particularly to your eyes. Never look directly into the antenna aperture
from a close distance while the radar is in operation or expose yourself to the
transmitting antenna at a close distance.
Distances at which RF radiation levels of 100 W/m2 and 10 W/m2 exist are given in
the table below.
Note: If the antenna unit is installed at a close distance in front of the wheel house,
it may be necessary to halt transmission within a certain sector of antenna
revolution. This can be done from the SCANNER menu.
Radiator type
Distance to Distance to
100 W/m2
10 W/m2
point
point
SN30AF
0.60 m
8.90 m
SN36AF
0.40 m
7.40 m
i
WARNING
WARNING
CAUTION
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
A proper license is necessary to install
a radar.
Only qualified personnel should work
inside the equipment.
Wear a hard hat and safety belt when
mounting the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna mast.
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna
mast.
Do not install units other than the
antenna unit in a place subject to rain
or water splash.
Fire, electrical shock or injury can result if
water leaks into those units.
Turn off the power at the switchboard
before beginning the installation.
Fire, electrical shock or injury can result if
the power is on during the installation.
Use only the specified power cables.
Use of power cables that are thinner than
those specified can cause fire.
Securely attach protective earth to the
ship's body.
The protective earth is required to prevent
electrical shock.
ii
See your dealer for details.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Standard Steering
compass compass
Antenna Unit
(50 kw)
3.75 m
2.45 m
Monitor Unit
(MU-201CR)
1.55 m
1.00 m
Processor Unit
(RPU-013)
1.35 m
0.85 m
0.30 m
0.30 m
0.95 m
0.60 m
0.65 m
0.45 m
Power Supply
Unit (PSU-006)
0.30 m
0.30 m
Memory Card
Interface Unit
(CU-200)
0.90 m
0.60 m
Switching Hub
(HUB-100)
1.00 m
0.60 m
Control Unit
(RCU-014)
Control Unit
(RCU-015)
Control Unit
(RCU-016)
TABLE OF CONTENTS
SYSTEM CONFIGURATION................................................................................iv
EQUIPMENT LISTS ..............................................................................................v
1. MOUNTING.................................................................................................. 1-1
1.1
1.2
1.3
1.4
1.5
Antenna Unit.................................................................................................................1-1
Monitor Unit (for FAR-2167DS) ....................................................................................1-7
Control Unit ................................................................................................................1-10
Processor Unit............................................................................................................1-15
Power Supply Unit......................................................................................................1-16
2. WIRING ........................................................................................................ 2-1
2.1
2.2
2.3
2.4
2.5
2.6
Wiring Overview ...........................................................................................................2-1
Antenna Unit.................................................................................................................2-2
Monitor Unit (for FAR-2167DS) ....................................................................................2-7
Processor Unit..............................................................................................................2-8
Power Supply Unit......................................................................................................2-13
Changing AC Power Specification .............................................................................2-15
3. ADJUSTMENTS .......................................................................................... 3-1
3.1
3.2
3.3
3.4
3.5
Initializing Tuning..........................................................................................................3-1
Heading Alignment .......................................................................................................3-2
Adjusting Sweep Timing...............................................................................................3-5
Suppressing Main Bang ...............................................................................................3-6
Other Settings ..............................................................................................................3-7
4. OPTIONAL EQUIPMENT ............................................................................ 4-1
4.1
4.2
4.3
4.4
Gyro Converter GC-10 .................................................................................................4-1
Memory Card Interface Unit .......................................................................................4-10
DVI-RGB Conversion Kit ............................................................................................4-13
BNC Connector Converter .........................................................................................4-16
5. IO DATA....................................................................................................... 5-1
PACKING LISTS ............................................................................................... A-1
OUTLINE DRAWINGS ...................................................................................... D-1
INTERCONNECTION DIAGRAM...................................................................... S-1
iii
SYSTEM CONFIGURATION
RADIATOR
SN30AF
SN36AF
ANTENNA UNIT
CHASSIS
RSB-111/112
POWER SUPPLY UNIT
PSU-006
200 VAC, 3φ, 50 Hz (For amtenna motor)
220 VAC, 3φ, 50 Hz
380 VAC, 3φ, 50 Hz
440 VAC, 3φ, 50 Hz
110 VAC, 3φ, 60 Hz
TRANSFORMER
RU-5693
220 VAC, 3φ, 50 Hz
TRANSFORMER
RU-6522
*
MONITOR UNIT
MU-201CR
(For FAR-2167DS)
CONTROL UNIT
RCU-014
(Standard)
OR
RCU-015
(Trackball)
TRANSFORMER
RU-5466-1
440 VAC, 3φ, 50 Hz
(For voltage power)
100-115V/220-230 VAC
1φ, 50/60 Hz
TRANSFORMER
440 VAC, 1φ,
RU-1803
50/60 Hz
Navigator
Speed Log
IEC-61162 Serial data
(I/O)
IEC-61162 Serial data
(Input)
PROCESSOR
UNIT
RPU-013
GYRO CONVERTER
GC-10
Gyrocompass
100-230 VAC
1φ, 50/60 Hz
REMOTE CONTROL UNIT
RCU-016
Radar Remote
Display
SWITCHING HUB
HUB-100
Alarm
AD-100
AIS
VDR
Track Controller
External
Monitor
MEMORY CARD
INTERFACE UNIT
CU-200-FAR
TRANSFORMER
RU-1803
: Standard supply
: Optional supply
: Local supply
100-115 VAC/
220-230 VAC
1φ, 50/60 Hz
440 VAC
1φ, 50/60 Hz
Equipment category
* FAR-2167DS-BB is not equipped with
a monitor unit. Procure one locally.
iv
Unit
Category
Antenna
Exposed to weather
Other units
Protected from weather
EQUIPMENT LISTS
Standard supply
Name
Antenna Unit
Type
Code No.
Qty
SN30AF
–
SN36AF
–
RSB-111
–
RSB-112
–
Power Supply
Unit
PSU-006
–
1
Monitor Unit
MU-201CR
–
1
Processor Unit
RPU-013
–
1
Control Unit
RCU-014
–
RCU-015
–
Installation
Materials*
Accessories*
Spare Parts*
1
1
1
1
Remarks
Radiator
200 VAC, 3φ, 50 Hz
220 VAC, 3φ, 60 Hz
Chassis
380 VAC, 3φ, 50 Hz
440 VAC, 3φ 60 Hz
For FAR-2167DS
Standard-type
Trackball-type
CP03-31501
008-573-780
For antenna unit
CP03-25700
000-080-435
CP03-25710
000-080-436
CP03-25730
000-082-191
CP03-25720
000-080-437
CP03-25800
000-080-434
1
Cable assy. for monitor unit
CP03-25602
008-535-940
1
For processor unit
CP03-31401
008-572-750
1
For power supply unit
CP03-25604
008-539-850
1
For control unit
FP03-09810
008-536-010
1
For monitor unit.
FP03-09850
008-535-610
FP03-09860
008-535-690
FP03-10101
008-538-730
SP03-14404
008-535-910
SP03-14405
008-535-920
SP03-14401
008-535-990
SP03-15501
008-572-730
SP03-15502
008-572-740
15 m signal cable (RW-9600)
1
30 m signal cable (RW-9600)
40 m signal cable (RW-9600)
50 m signal cable (RW-9600)
1
1
1
1
1
For standard-type control unit
For trackball-type control unit
For antenna unit
For processor unit, 100 VAC
For processor unit, 220 VAC
For monitor unit
For power supply unit, 100 VAC
For power supply unit, 220 VAC
* See packing list at end of this manual.
v
Optional equipment
Name
Type
Gyro Converter GC-10-2
Stepdown
Transformer
Unit
Code No.
000-080-440
Remarks
See Chapter 4.
RU-1803
–
440 to 100 VAC, for processor unit
RU-5693
–
110 to 220 VAC, 3φ, for antenna unit
RU-6522
–
220 to 200 VAC, 3φ, for antenna unit
440 to 200 VAC, 3φ, for antenna unit
RU-5466-1
–
Radar Remote
Display
FMD-8010
–
Memory Card
Interface Unit
CU-200-FAR
000-081-568
External Alarm
Buzzer
OP03-21
000-030-097
Remote
Control Unit
RCU-016
000-080-299
Remote type, w/FP03-09860
RAM Card
O0RAM08MC-005
004-376-740
8MB
DVI-RGB
Converter Kit
OP03-180-2
008-536-070
See Chapter 4.
Cable Assy.
XH10P-W-6P L=20M
000-149-748
Processor unitQControl unit, 20 m
XH10P-W-6P L=30M
000-149-749
Processor unitQControl unit, 30 m
XH10P-W-5P-A L=10M
000-149-050
Between control units, 10 m
XH10P-W-5P-A L=20M
000-149-051
Between control units, 20 m
XH10P-W-5P-A L=30M
000-149-052
Between control units, 30 m
DVI-D/D S-LINK 10M
000-150-200
Processor unitQControl unit, 10 m
S03-9-5(8-8P)
008-206-640
External radar, 5 m, 8-8P
S03-9-10(8-8P)
008-206-650
External radar, 10 m, 8-8P
S03-9-15(8-8P)
008-209-160
External radar, 15 m, 8-8P
CP03-28900
000-082-658
FR-FTPC-CY 10 m, modular
connector MPS588-C, 2 pcs.
CP03-28910
000-082-659
FR-FTPC-CY 20 m, modular
connector MPS588-C, 2 pcs.
CP03-28920
000-082-660
FR-FTPC-CY 30 m, modular
connector MPS588-C, 2 pcs.
Bracket Assy.
FP03-09820
008-535-560
Hanger assy. for monitor unit
Handgrip Assy.
FP03-09840
008-535-570
For monitor unit
Dust Cover
03-163-1201
100-307-260
For monitor unit
Clamp Assy.
OP03-182
008-535-620
For RCU-014
Flush Mount Kit FP03-09870
008-535-630
For control unit
Connection
Stand
OP03-183
008-535-640
RCU-014QMU-201CR
OP03-185
008-535-660
RCU-014
Hanger Kit
FP03-10201
008-539-530
Desktop inst. kit for CU-200-FAR
BNC
Connector
Converter
DSUB-BNC-1
000-148-528
For connecting VDR
Switching Hub
HUB-100
Installation
Materials
(Armored LANCable Kit)
.
vi
–
w/CP03-27430, see Chapter 4.
See Operator's Manual for HUB-100,
issued separately.
1. MOUNTING
1.1 Antenna Unit
Mounting considerations
The antenna unit is generally installed either on top of the wheelhouse, on the radar mast, or on
a suitable platform. The mounting location should afford a good all-round view and satisfy the
siting and mounting considerations mentioned below.
Siting
• No funnel, mast or derrick should be within the vertical beamwidth of the antenna unit in the bow
direction, especially zero degrees ±5°, to prevent blind sectors and false echoes on the radar
picture.
• Deposits and fumes from a funnel or other exhaust vent can adversely affect the aerial performance and hot gases may deform the radiator. The antenna unit must not be mounted where
the temperature is more than 70°C.
• Locate a direction finder antenna clear of the antenna unit to prevent interference to the direction finder. A separation of more than two meters is recommended.
• Choose a location where reflections from the radar reflector will not be received by the radar
antenna.
• The "standard" antenna unit orientation has the cable glands directed toward the bow.
• Leave sufficient space around the unit for maintenance and servicing. See the antenna unit outline drawing for recommended maintenance space.
Mounting
• Use rope and crane to hoist the antenna unit to the mounting location. Lifting fixtures are provided on the antenna chassis to which to fasten rope.
• Mount the unit parallel to the waterline.
• A hole is required in the mounting platform for the antenna cable.
• An appropriate platform should be constructed at the mounting location to facilitate installation
and maintenance work.
• Connect ground wire between antenna terminal on antenna chassis and ground point.
• If the mounting platform is made of steel paint it to prevent electrolytic corrosion. DO NOT paint
the antenna radiator.
1-1
Installation precaution for S-band antenna unit
If an S-band antenna unit is mounted near the end of a platform to provide sufficient rotation clearance for the radiator, the antenna unit, because of its weight, will swing up and down by ship's
vibration and rolling. This exerts excessive levels of stress at the base of the radiator, which can
damage the radiator. To prevent this, relocate the antenna unit, or if relocation is not possible reinforce the platform.
Mast for
DF, etc.
Remarkable vibration
(pitching)
Mounting
position
EXAMPLE
Mast for DF
Mount antenna unit
directly on mast or on
a platform, as near as
possible to center of mast.
Mounting precaution for S-band antenna unit
1-2
Assembling the antenna unit
The antenna unit should be assembled before mounting it. Follow the procedure below to
assemble the antenna unit.
1. Screw the guide pins (2 pcs.) in the radiator.
2. Remove the protective cap from the choke guide and radiator.
3. Grease the O-ring and set it to the groove on the choke guide.
4. Place the radiator on the radiator bracket. (Radiator direction is shown by the logo on the
bracket. If reversely oriented the radiator cannot be set to the bracket.)
5. Loosely fix the radiator to the radiator bracket with hex bolts (M10×25), spring washers and flat
washers.
6. Remove the guide pins and tighten the hex bolts.
Antenna radiator
Do not remove teflon tube
from the center conductor.
Spring washer,
flat washer,
10 pcs. each,
M10x25
Protective cap
Radiator bracket
Choke guide
O-ring
Radiator front
Guide pin (2 pcs.)
Arrow mark for the radiator front.
CAUTION
Be sure to remove the guide pins
after fixing the radiator.
Injury may result if the guide pins loosen
and fall from antenna radar platform.
Assembling the antenna unit
1-3
How to hoist the antenna unit
1. Fix the antenna radiator to the antenna unit chassis as shown on page 1-3.
2. Attach the lifting fixtures and collars as shown below.
3. Position the radiator as shown below and arrange the ropes A and B.
Lifting fixture
Supplied as accessories.
Remove after installation.
Collar
Spring washer
Spring washer
Flat washer (M12)
Hex bolt (M12x20)
(Torque: 63.5 Nm)
Remove lifting fixture, coat threads
of hex bolts with silicone grease, and
then insert bolts in antenna chassis.
Lifting hook (2 pcs.)
A
2m
B
*
1.8m
*
* 2. Place protective material
(cardboard, foam, etc.) between
rope and radiator at the
asterisk-marked locations, to
prevent damage to radiator.
Attachment of lifting fixtures, collar and ropes
1-4
Fastening the antenna unit to the mounting platform
WARNING
Do not open the equipment unless
totally familiar with electrical circuits
and service manual.
Only qualified personnel should
work inside the equipment.
Wear a hard hat and safety belt when
mounting the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna mast.
Construct a suitable service platform
from which to install the antenna unit.
Serious injury or death can result if
someone falls from the radar antenna
mast.
Note: The antenna is made of cast aluminum, which is subject to electrolytic corrosion if the
mounting platform is steel or iron. To prevent electrolytic corrosion, use the supplied seal washers
and corrosion-proof rubber mat.
Fix the antenna unit to the mounting location, referring to the procedure below and the illustration
on the next page.
1. Referring to the antenna outline drawing, prepare a mounting platform. Drill eight fixing holes
of 15 mm in diameter in the mounting platform or the deck.
• The diameter of the mast for the mounting platform must be over 250 mm.
• The thickness of the platform must be over 15 mm.
• The reinforcement rib must be installed diagonally as shown below.
Over 15 mm
Use two nuts.
At least 250 mm in diameter,
Thickness at least 6 mm.
Install the reinforcement
rib diagonally.
Ship's bow
Bottom view
Installation of reinforcement ribs
1-5
2. Lay the corrosion-proof rubber mat (supplied) on the mounting platform, aligning the holes on
the rubber mat with the fixing holes on the mounting platform.
3. Lay the antenna unit on the rubber mat, orienting it so the cable gland is directed toward ship's
bow. Remove the lifting fixtures and collars.
4. Fix the antenna base to the mounting platform with four M12×70 hex bolts, nuts, washers and
seal washers (supplied).
5. Arrange the ground point at a location on the mounting platform that is within 300 mm from the
ground terminal on the antenna unit. Fasten the ground wire (RW-4747, 340 mm) there, using
the M6×25 hex bolt, nut and washers.
6. Connect the other end of the ground wire to the ground terminal on the antenna unit.
7. Coat the ground terminal, ground point on the mounting platform and fixing bolts on the
antenna unit with anticorrosive sealant (supplied).
Seal
washer
Corrosionproof
rubber
mat
Use two nuts.
(Torque: 63.5 Nm)
Ground terminal
G1_1/4-A
Lay corrosion-proof rubber mat,
bolt antenna unit to mounting
location, and coat exposed
hardware with anticorrosive sealant.
Hex bolt
Flat washer
Flat washer
Spring washer
Hex nut
Ground wire
Coat with
anticorrosive
sealant.
Fasten ground wire and then
coat with anitcorrosive sealant.
OR
Ground wire
Hex nut
Spring washer
Flat washer
Hex bolt
Ground wire
Welding
Antenna chassis
Arrange ground terminal as close
as possible to antenna unit.
Ground terminal provided on antenna base.
Mounting the antenna unit
1-6
1.2 Monitor Unit (for FAR-2167DS)
The monitor unit is can flush mounted in a panel or mounted on a desktop (requires optional
accessories).
The FAR-2167DS-BB is not equipped with a monitor unit. Procure a suitable monitor unit locally.
Recommended monitor: SXGA (1280×1024), aspect ratio 5:4.
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Select a location where the screen can be viewed conveniently while facing the bow.
• Locate the unit out of direct sunlight and away from heat sources because of heat that can build
up inside the cabinet.
• Locate the unit away from places subject to water splash and rain.
• Leave sufficient space on the sides and rear of the unit to facilitate maintenance, referring to the
outline drawing for maintenance space.
• The monitor unit will give interference to a magnetic compass if it is placed too close to the compass. Observe the compass safe distances on page ii to prevent interference to the compass.
Mounting procedure
Flush mounting
Follow the procedure below to mount the monitor unit in a console.
1. Make a cutout in the mounting location referring to the outline drawing shown below.
2. Set the monitor unit to the hole and fix it with four self-tapping screws (6×30).
3. Attach panel hooks near the fixing holes (upper part). See next page. These are used to pull
out the monitor unit from the panel for servicing.
4. Attach four panel covers to the fixing holes.
1
4-FIXING HOLES
(79)
296 1
454
296 1
420
506
490
506 1
534
4-φ8
FIXING HOLES
30
80
Mounting dimensions for flush mounting the monitor unit
1-7
Panel hook
Panel cover
Fixing screw
How to attach panel hook and panel cover
Note: If you need to remove the monitor unit from the console, remove the four panel covers with
your fingernail and use two panel hooks supplied as accessories to lift the monitor unit.
Desktop mounting
Use the optional desktop mouting kit (Type: FP03-09820, Code No.: 008-535-560) to mount the
monitor unit on a desktop.
Contents of desktop mounting kit FP03-09820
Name
Type
Code No.
Qty
Hanger L
03-163-1111
100-305-141
1
Hanger R
03-163-1112
100-305-181
1
Hanger stay
03-163-1113
100-305-191
1
Hole plug
CP-30-HP-13
000-147-143
2
Snap button
KB-13, Black
000-570-276-10
4
Hex. bolt
M6×25
000-802-771
4
Hex. bolt
M10×30
000-802-182
2
Spring washer
M10
000-864-261
2
Flat washer
M10
000-864-131
2
1. Assemble two hangers and hanger stay with two hex bolts (M10×30), flat washers and spring
washers and cover each hex bolt with hole plug.
2. Fix the above assembly to the mounting location with four hex bolts (M12, dockyard supply).
3. Fasten the monitor unit to the mounting hanger assembly with four hex bolts (M6×25, supplied).
4. Cover each hex bolt with a panel cover (4 pcs.).
5. Cover fixing holes for hand grips with snap buttons (4 pcs).
1-8
Hanger (L)
M12 bolts for fixing
(Dockyard supply)
Hanger stay
Hanger (R)
Panel cover
Snap button
Flat Washer M10
Spring Washer M10
Hex bolt
(M6x25)
Hex bolt
M10x30
Hole plug
Panel cover
To remove this, insert fingernail in groove.
Fastening monitor unit to hanger
Attaching hand grips
Hand grips are optionally available for the desktop-mount monitor unit. Attach them as follows:
1. Remove the snap buttons attached at step 5 on the previous page.
2. Fix hand grips with wave washers, rosette washers and flat head screws.
Wave washer
Rosette washer
Flat head screw (torque: 7.6 Nm)
Hand grip
How to attach hand grips
1-9
1.3 Control Unit
Mounting considerations
The control unit may be mounted on a desktop, with or without the KB fixing metal (supplied) which
mounts the control unit at an angle. When selecting a mounting location, keep in mind the following points:
• Select a location where the control unit can be operated conveniently while observing the display screen.
• Locate the unit away from heat sources because of heat that can build up inside the cabinet.
• Locate the equipment away from places subject to water splash and rain.
• Determine the mounting location considering the length of the signal cable between the control
unit and the processor unit. (A 10 m signal cable is attached to the control unit.)
• A magnetic compass will be affected if the control unit is placed too close to it. Observe the compass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Fixing with KB (keyboard) fixing plate
The KB fixing plate sits the control unit at a comfortable angle, like the retractable legs on a PC
keyboard.
1. Fix the KB fixing plate to the bottom of the control unit.
2. Attach cushions (three for RCU-014, two for RCU-015/RCU-016) to the bottom of the control
unit as shown below.
3. Fix the unit to a desired location with self-tapping screws (local supply).
KB fixing plate
Cushion
Control unit RCU-014/015/016, side view
1-10
Fixing without KB fixing plate
1. Drill four mounting holes of 5 mm diameter, referring to the outline drawing at the back of this
manual.
2. Fix the control unit with four screws (M4) from the under side of the desktop. (M4 screws with
a sufficient length for the thickness of the desktop should be provided locally.)
# Minimum recommended service space
180
136±1
#70
4-M4 (Fixing holes)
(bottom)
308±1
398
Mounting dimensions for control unit RCU-014
24
32
F3
180
136±1
F1
F2
F4
110±1
160
4-M4 (Fixing holes)
(REAR)
Mounting dimensions for control unit RCU-015/RCU-016
1-11
Flush mounting
Use the optional flush mount kit FP03-09870 (Code No. 008-535-630) to flush mount the control
unit RCU-014, RCU-015 and/or RCU016 in a console.
Contents of flush mount kit for RCU-014/015/016
Name
Type
Qty
Mounting plate
03-163-7531
4
Hex bolt
M5
4
Wing screw
M5×40
4
Pan head screw
M4×12
4
1. Prepare a cutout in the mounting location as shown in the figure below.
170±2
176±2
388 ±2
150±2
Flush mount cutout for RCU-014
Flush mount cutout for RCU-015 and RCU-016
2. Set the control unit to the cutout.
3. From the rear side, attach the mounting plate to the control unit with four screws.
4. Screw the wing screw to each mounting plate and then insert hex bolt to each wing screw.
53
(P)
#70
92
53
#70
86
(P)
5. Fasten each wing screw and then fasten the hex nuts as shown in the figure below.
171
Note:
P <
=10
# Minimum recommended service space
To change location of
cable entrance, see
page 1-14.
Flush mount mounting dimensions for control unit RCU-014 (left) and RCU-015/RCU-016
1-12
Connecting RCU-016 in series with RCU-014
1. Pass the cable from RCU-016.
2. Plug in connector
to J502.
3. Clamp the copper part of the cable with the cable clamp.
Control unit RCU-014, inside view
1-13
Changing the cable entrance on control unit RCU-015/RCU-016
To change the cable entrance from the side (default) to the bottom, modify the unit as shown
below.
Screw M3X8
(torque: 10.78 Nm)
Bottom of unit
2. Pull out cable.
3. Pass cable thru this hole.
Cable clamp
03-163-7804
Screw M4X8
(torque: 1.47 Nm)
4. In here, clamp copper part
of cable with cable clamp
removed at step 1.
1. Remove cable
clamp.
J522: Plug in here to connect RCU-016 in series with RCU-015.
Changing cable entrance on control unit RCU-015/RCU-016
1-14
1.4 Processor Unit
Mounting considerations
When selecting a mounting location, keep in mind the following points:
• Locate the processor unit away from heat sources because of heat that can build up inside the
cabinet.
• Locate the unit away from places subject to water splash and rain.
• Leave sufficient space at the sides and rear of the unit to facilitate maintenance, referring to the
outline drawing.
• A magnetic compass will be affected if the processor unit is placed too close to it. Observe the
compass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Fix the unit with four M6 bolts or self-tapping screws.
#50
2-φ7 FIXING HOLES
25
385
# Minimum recommended
service space
380
410
340±1
370±1
R3
.5
7
2-FIXING NOTCH
350±1
Mounting dimensions for processor unit
Upper case assy.
Note: If you fix the unit with the
cable entry up, do not unfasten
the screw (M3x10) that fastens
the upper case assy. and lower
case assy. of the processor unit.
Lower case assy.
Do not unfasten
this screw.
1-15
1.5 Power Supply Unit
Mounting considerations
The power supply unit may be mounted on a bulkhead or a deck. Because it has no operation
requirements it can be located almost anywhere, provided the location is well ventilated.
Mounting procedure
Fix the unit to the mounting location with four 6×20 self-tapping screws (local supply). For
mounting on a bulkhead, do the following:
1. Mark location for mounting holes.
2. Screw in the self-tapping screws at the location for the bottom fixing holes, leaving a gap of
about 5 mm between the bottom of the screw head and bulkhead.
3. Set the unit to the screws inserted at step 1.
4. Fasten the self-tapping screws at the top of the unit.
5. Tighten all self-tapping screws.
#50
2-φ7 FIXING HOLES
25
385
# Minimum recommended
service space
380
410
340±1
370±1
R3
.5
7
350±1
2-FIXING NOTCH
Mounting dimensions for power supply unit
1-16
2. WIRING
2.1 Wiring Overview
POWER
SUPPLY
UNIT
TPYCY-2.5
TPYCY-1.5
ANTENNA UNIT
MONITOR UNIT
(For FAR-2157)
TB801
TB802
24 VDC
TPYC-2.5
RW-9600
15/30/40/50 m
(Max.100 m)
RU-5693
TPYC-1.5
110 VAC, 3φ,
60 Hz
220 VAC, 3φ,
50 Hz
440 VAC, 3φ,
50 Hz
RU-3423
RU-6522
RU-5466-1
100-115 VAC/220-230V,
1φ, 50/60 Hz
440 VAC,
1φ, 50/60 Hz
RU-1803
DPYC-2.5
100/110/115/
220/230 VAC
1φ, 50/60 Hz
DVI-D/D SINGLELINK 5/10m
200 VAC, 3φ, 50 Hz
220 VAC, 3φ, 60 Hz
PROCESSOR UNIT
DPYC-2.5
CONTROL UNIT
(RCU-014 or RCU-015)
MEMORY CARD
INTERFACE
CU-200-FAR
XH10P-W-5P
L=10/20/30 m
100-230 VAC
1φ, 50/60 Hz
XH10P-W-6P L=1.5/10/20/30m
CONTROL UNIT
(RCU-016)
DPYC-2.5
: Fabrication required
100-115V/220-230 VAC
1φ, 50/60Hz
F1
F2
F3
F4
2-1
2.2 Antenna Unit
Antenna safety switch
Gland for HV cable (TYPCY-1.5)
Cover (right side)
Gland for power cable
(TPYCY-2.5)
Gland for signal cable (RW-9600)
Ground terminal
Antenna unit, front view
Fabricating signal cable RW-9600 and HV cable TYPCY-1.5
1. Use a ratchet or box wrench (diagonal 13 mm) to open port- and starboard-side covers on the
antenna unit.
2. Unfasten the gland nut for the signal cable and remove the gasket, flat washers (3 pcs.) and
gland cap. (The gland cap may be discarded.)
3. Fabricate the signal cable as follows:
a)
b)
c)
d)
e)
f)
g)
Remove the vinyl sheath, armor and sheath by the amounts shown in the figure below.
Unravel the shield to expose cores.
Shorten cores (except coax) considering their locations on the terminal inside the antenna unit.
Shorten the shield, leaving 210 mm. Attach crimp-on-lug (FV5.5-4, yellow, φ4) to shield.
Remove the sheath of cores by 6 mm.
Unravel armor.
Fix vinyl wire, coaxial cable and shield by taping the shield with vinyl tape at the location shown
below.
Vinyl
sheath
Sheath
Armor
20 mm
Shield
450 mm
5 mm
500 mm
Coaxial cable
Vinyl wire
Shield
Taping
6
14 5 9
Unravel armor.
Core
Fold back shield.
Shield
Crimp-on lug
Coaxial cable
Fabricating signal cable RW-9600
2-2
4. In the order shown in the figure below, pass the gland nut, flat washers (3 pcs.) and gasket onto
the signal cable.
Armor
Gasket
Flat washer
(2)
Signal cable
Flat washer Gland nut
(1)
5. As shown in the figure below, fold back the armor onto flat washer (2) and insert remaining
armor through flat washer (3). Cut off the part of the armor that protrudes past the flat washers
(2) and (3).
Flat washer
(3)(2) (1)
Fold back armor
Flat washer (2)
Cut off armor that protrudes
past flat washer.
6. Lead the signal cable through its cable gland and then into the chassis. Coat the threaded part
of gland nut with sealant (supplied) and then tighten the nut.
Gland for HV
cable (TPYCY-1.5)
TB Board
Gland for
signal cable
(RW-9600)
TB801
Connect shield of signal cable here.
Coaxial
TB803 cable
TB802
Fastening coaxial cable
Antenna unit, front view
2-3
7. Using the terminal opener provided, connect cores (except coaxial cable) to their appropriate
locations on TB801 on the TB Board. Refer to the interconnection diagram for wiring details.
8. Connect the coaxial cable to TB802, referring to the right-hand illustration below..
Wiring WAGO connector
Push down.
Fastening coaxial cable
Fasten shield
by clamp.
Terminal opener
Taping
Wire
Twist
Fasten conductor with screw.
WAGO connector
NOTICE
Procedure
1. Twist core.
2. Insert terminal opener as shown and
push down.
3. Insert core into hole.
4. Release terminal opener.
5. Pull wire to confirm that it is firmly in
place.
Fasten BARE conductor. Do not use
crimp-on lug, to prevent increased
contact resistance.
How to wire WAGO connector
9. Attach crimp-on lug (FV5.5-4) to the shield of the signal cable and fasten it with the screw at
the location specified in the illustration on the preceding page.
10.Process unused cores as follows:
a) Slip shrink tubing onto cores and heat.
b) Bind unused cores with cable tie.
11.Unfasten the gland nut for the HV cable and remove gasket, flat washers (3 pcs.) and gland
cap. (The gland cap may be discarded.)
12.Fabricate the HV cable as shown below.
20 mm
5 mm
Sheath
Armor
6
Sheath
L
Vinyl
sheath
Conductor
S = 1.50 mm2
φ = 1.56 mm
Armor
L: 300 mm (red)
L: 370 mm (black, white)
SECTIONAL VIEW
How to fabricate HV cable TYPCY-1.5
2-4
13.In the order shown in the figure below, pass the gland nut, flat washers (3 pcs.) and gasket
onto the HV cable.
14.As shown in the figure below, fold back the armor onto the flat washer and insert it thru the
other flat washer. Cut off the part of the armor that protrudes past the washer.
Flat washer
(1) (2) (3)
HV cable
Cut off armor that
protrudes past washer.
Gland nut
Gasket
15.Pass the HV cable through its cable gland and tighten gland nut.
16.Using the terminal opener, connect wiring to TB901, referring to the interconnection diagram.
CAUTION
High voltage is present at the No. 6 pin
of TB901. Miswiring at this pin can
damage the antenna unit.
17.Close the cover.
18.Seal the cable gland for the HV cable with putty.
Fabricating the power cable TYPCY-2.5
1. Use a ratchet or box wrench to open the port-side cover on the antenna unit.
2. Unfasten the gland nut for the power cable and remove gasket, flat washer (3 pcs.) and gland
cap. (The gland cap may be discarded.)
3. Fabricate the power cable as shown below. Unravel the armor. Wrap sheath with vinyl tape to
fix base of vinyl wire.
Armor
Sheath
25 mm
5 mm
Sheath
FV2-4
Conductor
S = 2.50 mm2
φ = 2.01 mm
230 mm
Vinyl sheath
Armor
SECTIONAL VIEW
How to fabricate power cable TYPCY-2.5
2-5
4. In the order shown in the figure below, pass the gland nut, flat washers (3 pcs.) and gasket onto
the power cable.
5. As shown in the figure below, fold back armor onto flat washer and insert it thru the other flat
washer. Cut off part of armor that protrudes past flat washer..
Flat washer
(1) (2) (3)
25 mm
5 mm
Sheath
Power cable
FV2
230 mm
Vinyl sheath
Armor
Cut off armor that
protrudes past washer.
Gland nut
Gasket
Passing flat washer, etc. onto HV cable
6. Pass the power cable though its cable gland and then tighten the gland nut..
7. Pass the power cable to the rear of the antenna unit.
Terminal for power cable
Cable gland for power cable
(TPYCY-2.5)
Antenna unit, left-side view
8. Connect the power cable to its terminal, referring to the interconnection diagram.
9. Close the cover.
10.Seal the cable gland for the power cable with putty.
2-6
2.3 Monitor Unit (for FAR-2167DS)
Two cables are terminated at the monitor unit: the signal cable from the processor unit (5 m or 10
m cable) and the power cable from the ship's mains. The signal cable comes with a connector preattached to it for connection to the monitor unit. Fabricate the power cable as below. Use DPYC2.5 (Japan Industry Standard) cable or the equivalent. Be sure to ground the unit, with IV-8sq wire
(local supply).
Note: Pass the AC line through a double-contact breaker (shipyard supply). Further, for vessels
where the power line is grounded, connect one end of the line to the C (common) terminal and the
other end to the H terminal.
Fabricating the power cable DPYC-2.5
1. Remove the armor from the cable by 40 mm.
2. Remove the vinyl sheath by 35 mm.
3. Remove the insulation from the cores by about 10 mm..
4. Peel paint from the armor by 40 mm.
5. Cover the end of the armor with vinyl tape. Fix crimp-on lugs (FV5.5-4, yellow) to the cores.
(1)
DPYC-2.5
Armor
Approx. 40 mm
Armor
35 mm
(2)
Vinyl sheath
Conductor
S = 2.5 mm2
φ = 2.01 mm
SECTIONAL VIEW
10 mm
(3)
40 mm: Peel paint.
(4),
(5)
Crimp-on lug
Taping
Fabricating power cable DPYC-2.5
Cable entrance for signal cable
(Connect end which has no EMI core here.)
Cable entrance for power cable
Monitor unit MU-201CR, rear view
2-7
2.4 Processor Unit
Four cables are terminated at the processor unit: the antenna unit cable, monitor unit cable (FAR2167DS only), control unit cable and the power cable. Cables other than the power cable come
with a connector preattached to them. Fabricate the power cable as below.
Note: Pass the AC line through a double-contact breaker (shipyard supply). Further, for vessels
where the power line is grounded, connect one end of the line to the C (common) terminal and the
other end to the H terminal.
Fabricating the power cable DPYC-2.5
1. Remove the armor from the cable by 40 mm.
2. Remove the vinyl sheath by 35 mm.
3. Remove the insulation from the cores by about 10 mm.
4. Peel paint from the armor by 40 mm.
5. Tape the end of the armor with vinyl tape. Fix crimp-on lugs (FV5.5-4, yellow, supplied) to the
cores.
(1)
DPYC-2.5
Armor
Approx. 40 mm
Armor
35 mm
(2)
Vinyl sheath
Conductor
S = 2.5 mm2
φ = 2.01 mm
SECTIONAL VIEW
10 mm
(3)
40 mm: Peel paint.
(4),
(5)
Crimp-on lug
Taping
Fabricating power cable DPYC-2.5
2-8
Connection of cables
The power cable is connected to the terminal board on the rear panel and the signal cable from
the monitor unit is connected to the DVI-D connector. Other cables are connected to the printed
circuit board 03P9342. Be sure to ground the unit, with IV-8sq wire (local supply).
Cable clamp for power cable
Monitor unit
*
Network
Terminal board for power cable
DVI-D monitor
Remove the
protective cover.
F70
FUSE
1
15
DC/AC
F1
2
Control unit**
Heading senor
Speed log
Navigator
Power cable
9 14
ACK
Cable clamp
17
21
2
3
4
5
HDG
φ9
6
18
19
20
RSD
φ18.9
1
7
AIS
AD100
8
28
GYRO
PSU004
φ7.4
24'
φ7
26
VDR OUT
Memory Card IF unit
VDR OUT
Antenna unit
GND TERMINAL
24
VDR IN
VDR IN
Power supply unit
Gyrocompass
AD-100
AIS
Processor unit, rear view
*: The connector with EMI core should be connected to the processor unit.
**: The configuration of optional cable between the processor unit and the control unit is as follows.
Note that the cable fabrication for each end is different.
Control unit
Processor unit
150 mm
1.5/20/30 m
300 mm
Cable XH10P-W-6P L=20/30M
When the RCU-016 is installed, optional cable (XH10P-W-5P-A, L=10/20/30M) is required. Cable
fabrication for each end is the same.
Control unit
Processor unit
150 mm
10/20/30 m
150 mm
Cable XH10P-W-5P-A L=10/20/30M
2-9
Location of connectors
Open the processor unit as shown below to access the 03P9342 board, which is for connection
of external equipment.
Cable clamp
Cables from power supply unit
03P9342
J621
J612
J608
Gyro converter board
or AD-100
J607
External alarm
Speed log
J620
J606
Track control
J611
AIS
J619
Navigator
J605
ECDIS
J603
Gyro converter board
J618
To Sub display *
(SEMI-LOG)
To Sub display *
(FULL-LOG)
From Master radar
J610
J604
J602
PSU
J617
Cable from the
control unit
J616
Cable from antenna unit
J614 J615
J601
+12V for card I/F
J613
PC
J609
J654
Tx HV line
Coaxial wire
Location of connectors inside the processor unit
*: See page 2-11 for details.
2-10
Heading sensor
Cable fabrication for the cables connected to the 03P9342 board
Signal cable RW-9600 (Between antenna unit and processor unit)
Vinyl sheath
Armor
Shield
450
60
5
Expose cores, and then
wind shield around armor.
Vinyl tape
6
14 5 9
Coaxial cable
Conductor
Fold back shield.
Coaxial cable
Fasten cable clamp here.
Power cable TPYC-1.5
Armor
60: Peel paint
L: According to location
of connector.
6
L
Cables for optional equipment (use TTYCS-1 or TTYCS-4, or equivalent)
Armor
60: Peel paint.
Armor
Shield
Sheath
Shield
L= Depends on equipment
connected. Measure at
processor unit.
φ = 10.1 mm
L
5
Conductor
S = 0.75 mm 2
φ = 1.11 mm
TTYCS-1
Vinyl tape
Expose cores, and then
wind shield around armor.
6
Fasten cable clamp here.
Armor
Sheath
φ = 16.3 mm
Shield
Conductor
S = 0.75 mm 2
φ = 1.11 mm
TTYCS-4
2-11
Wiring WAGO connector
Push down.
Fastening coaxial cable
Fasten shield
by clamp.
Terminal opener
Taping
Wire
Twist
Fasten conductor with screw.
WAGO connector
Procedure
1. Twist core.
2. Insert terminal opener as shown and
push down.
3. Insert core into hole.
4. Release terminal opener.
5. Pull wire to confirm that it is firmly in
place.
NOTICE
Fasten BARE conductor. Do not use
crimp-on lug, to prevent increased
contact resistance.
Connection of Sub-display
A conventional remote display and/or FAR-2xx7 series radar can be connected to J617 (FULLLOG) and J618 (SEMI-LOG) in the processor unit as a sub-display. However, the control for GAIN
and STC are different depending on J617 and J618. Refer to the table to connect sub-displays.
Port
Conventional remote display
FAR-2167DS
Even if input video level is adjusted
to 4 Vp-p, the gain is 8 db lower
than that on the master radar.
The gain is 8 dB lower than that
on the master radar.
The GAIN control is effective.
The GAIN control has no effect.
The STC control is effective.
The STC control has no effect.
Overall gain
When input video level is adjusted
to 4 Vp-p, the gain becomes the
same as that on the master radar.
The gain is almost same as that
on the master radar.
GAIN control
The GAIN control is effective.
The GAIN control has no effect.
STC control
The STC control changes the radar The STC control has no effect.
image, however STC is doubly
applied, resulting in improper radar
picture. Therefore, it is not recommended to use this port.
J617(FULLOverall gain
LOG)GAIN
and STC are
not conGAIN control
trolled. Video
STC control
signal for
conventional
sub display is
output.
J618(SEMILOG)Video
signal of
main radar
controlled
GAIN and
STC is
output.
2-12
2.5 Power Supply Unit
Wire the power supply unit referring to the interconnection diagram. Be sure to ground the unit,
with IV-8sq wire (local supply).
Note: Pass the AC line through a double-contact breaker (shipyard supply). Further, for vessels
where the power line is grounded, connect one end of the line to the C (common) terminal and the
other end to the H terminal.
CAUTION
High voltage is present at the
No. 6 pin of TB3. Miswiring at
this pin can damage the unit.
TB3: Power output line, control line
Ground
Cable clamp: Locate armor of cables in clamp.
TB1, TB2: Power input line
Power supply unit, inside view
Fabricating cable connected to terminal TB1, TB2, TB3
Terminal TB1: cable DPYC-2.5
See page 2-8 for sectional view of cable if using equivalent cable.
Armor
30: Remove paint.
FV2-4
120
2-13
Terminal TB2: cable TPYC-2.5 (for antenna motor)
Terminal TB3: #11-#13, cable TYPC-1.5 (between power control section and processor)
See page 2-5 for sectional views of these cables if using equivalent cables.
Armor
30: Peel paint
FV2-4
L
L: 100 (For TPYC-2.5)
150 (For TPYC-1.5)
Terminal TB3: #1-#3 TPYCY-2.5 (between power control section and antenna)
Terminal TB3: #6, #8, #9 TPYCY-1.5 (between power control section and antenna)
Armor
Vinyl sheath
FV2-4
L
30
L: 80 (For TPYCY-2.5)
120 (For TPYCY-1.5)
Armor
φ = TYPCY-1.5: 14.5 mm
TPYCY-2.5: 15.5 mm
Sheath
Conductor
S= TPYCY-1.5: 1.52 mm, TPYCY-2.5: 2.52 mm
φ = TPYCY-1.5: 1.56 mm, TPYCY-2.5: 2.01 mm
2-14
2.6 Changing AC Power Specification
To change AC power specification from 100 VAC to 220 VAC and vice versa, change fuse and
jumper wire setting, following the instructions in this section.
Processor unit
As directed in the table below, add or remove jumper connector P108 from the PWR board
03P9339 and change the fuse in the processor unit according to ship's mains. Then, adjust the
overvoltage detection circuit, the procedure for which is shown on the next page.
Note: When switching from 220 VAC to 100 VAC, construct a jumper connector locally, referring
to the illustration on the next page. (VH8 connector housing is to be plugged into J108.)
Power supply
Fuse
Jumper connector P108
100 VAC
10A
Necessary
220 VAC
5A
Unnecessary
Cover of PWR board
Fuse
PWR board
Upper part of processor unit
(SPU assembly omitted)
Processor unit, inside view
2-15
J105
J106
PWR board
(P)HV
J104
J103
R21
(OVER)
J101
P108/J108
AC FIL
87654321
Jumper connector
(VH8P)
Processor unit, inside view
How to adjust the overvoltage detection circuit:
1. Add or remove the jumper connector P108 as appropriate and change the fuse, referring to the
table on the previous page for details.
2. On the PWR board, set R21 fully clockwise.
3. Connect a variable transformer between ship's mains and the input power terminal board TB1 in the processor unit.
4. Adjust the variable transformer output (i.e., input voltage to the processor unit) as follows:
For 100 VAC set: 144 VAC
For 220 VAC set: 288 VAC
5. Turn on the radar and rotate R21 counterclockwise gradually until the overvoltage detection circuit activates (i.e., power supply cuts off).
6. Lower the output voltage of the variable transformer and confirm that the radar automatically
turns on with a voltage lower than 142 VAC or 284 VAC.
7. Gradually increase the output voltage of the variable transformer and confirm that the overvoltage detection circuit activates at 144 V or 288 VAC of the variable transformer output.
8. Assemble and connect the processor unit.
2-16
Power supply unit
Refer to the illustration and table below to add (or remove) jumper connector P8 from the TX-HV
Board (03P9350) and change fuse.
After completing jumper and fuse arrangements, adjust the overvoltage detection circuit, using a
variable transformer.
Note: When switching from 220 VAC to 100 VAC, construct a jumper connector locally, referring
to the illustration below. (VH6 connector housing is to be plugged into J8.)
Power
Fuse
Jumper connector P8
100 VAC
5A
Required
220 VAC
3A
Unnecessary
P8/J8
654321
Unfasten four screws and remove
cover for TX-HV Board.
Jumper connector
(VH6P)
CR23
R21
Fuse
TX-HV Board
2-17
How to adjust the overvoltage detection circuit
1. Add or remove the jumper connector P8 as appropriate and change the fuse, referring to the
table above for details.
2. On the PWR board, set R21 fully clockwise.
3. Connect a variable transformer between ship's mains and the input power terminal board
TB-1 in the processor unit.
4. Adjust the variable transformer output (i.e., input voltage to the processor unit) as follows:
For 100 VAC set: 144 VAC
For 220 VAC set: 288 VAC
5. Turn on the radar and rotate R21 counterclockwise gradually until the overvoltage detection circuit activates (i.e., power supply cuts off).
6. Lower the output voltage of the variable transformer and confirm that the radar automatically
turns on with a voltage lower than 142 VAC or 284 VAC.
7. Gradually increase the output voltage of the variable transformer and confirm that the overvoltage detection circuit activates at 144 V or 288 VAC of the variable transformer output.
8. Assemble and connect the power supply unit.
2-18
3. ADJUSTMENTS
This section provides the information necessary for setting and adjusting the radar, which is carried out from the radar's menu system. Menus may be accessed from the keyboard or on-screen
menu in case of Control Unit RCU-014, or on-screen menu in case of Control Unit RCU-015.
The menu illustrations in this chapter show default settings in bold face.
3.1 Initializing Tuning
1. Transmit the radar on 48 nm range.
2. Rotate the [GAIN] control until the value on the gain bar is 70-80.
3. Left-click the MENU box at the right side of the screen.
4. Spin the thumbwheel to choose 1 ECHO and then push the thumbwheel.
[ECHO]
1 BACK
2 2ND ECHO REJ
OFF/ON
3 TUNE INITIALIZE
5 SART
OFF/ON
6 WIPER
OFF/1/2
7 ECHO AREA*
CIRCLE/WIDE/ALL
* Not available with IMO radar
ECHO menu
5. Spin the thumbwheel to choose 3 TUNE INITIALIZE.
6. Push the thumbwheel to initialize automatic tuning.
In a few moments echoes appear on the screen. The message "TUNE INITIALIZE" appears (in
red) during automatic tuning. When this message disappears, the tuning is completed. If necessary adjust the [GAIN] control to show echoes clearly.
7. Push the right button twice to close the menu.
3-1
3.2 Heading Alignment
You have mounted the antenna unit facing straight ahead in the direction of the bow. Therefore,
a small but conspicuous target dead ahead visually should appear on the heading line (zero
degrees). In practice, you will probably observe some small bearing error on the display because
of the difficulty in achieving accurate initial positioning of the antenna unit. The following adjustment will compensate for this error.
Correct bearing
relative to heading
α
Target
340
α
350 000
010
020
330
030
320
040
310
050
060
300
070
290
280
080
270
090
260
100
250
110
240
120
230
130
140
220
210
150
200
190
180
170
160
Picture appears
deviated clockwise.
Antenna mounted error
to port (HDG SW
advance)
β
Apparent position
of target
β
Target
340
350 000
010
020
330
030
320
040
310
050
060
300
070
290
280
080
270
090
260
100
250
110
240
120
230
130
140
220
210
150
200
Antenna mounted error
to starboard (HDG
SW delayed)
Apparent
position
of target
190
180
170
Correct
bearing
relative to
heading
160
Picture appears
deviated counterclockwise.
Heading alignment
1. Select a stationary target echo at a range between 0.125 and 0.25 nm, preferably near the
heading line.
2. Operate the EBL control to bisect the target echo:
a) Roll the trackball to place the arrow in the EBL1 or EBL2 box (at bottom left corner), whichever
EBL you want to use.
b) Push the left button to turn on the EBL.
c) Push the left button again to send the cursor inside the effective display area.
d) Roll the trackball (coarse adjustment) or spin the thumbwheel (fine adjustment) to bisect the
target with the EBL.
3. Read the target bearing.
4. Measure the bearing of the stationary target on the navigation chart and calculate the difference
between actual bearing and apparent bearing on the radar screen.
5. Left-click the MENU box at the right side of the screen to close the menu.
3-2
6. For Control Unit RCU-014:
a) While pressing and holding down the [HL OFF] key, press the [MENU] key five times.
b) Press the [0] key to show the INITIALIZE menu.
For Control Unit RCU-015:
See the procedure on the next page for how to show the INITIALIZE menu.
[INITIALIZE]
1
2
3
4
5
6
7
8
BACK
[ECHO ADJ]
[SCANNER]
[INSTALLATION]
[OWN SHIP INFO]
[ARP PRESET]
[NETWORK]
[OTHER]
INITIALIZE menu
7. RCU-014: Press the [2] key to open the ECHO ADJ menu.
RCU-015: Choose 2 ECHO ADJ and then push the thumbwheel.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
8. RCU-014: Press the [3] key to choose HD ALIGN.
RCU-015: Choose 3 HD ALIGN and then push the thumbwheel.
9. RCU-014: Key in the bearing difference. The setting range is 0 to 359.9(°).
RCU-015: Spin the thumbwheel to set the bearing difference and then push the thumbwheel.
The setting range is 0 to 359.9(°).
10.Confirm that the target echo is displayed at correct bearing on the screen and then push the
thumbwheel.
11.RCU-014: Press the [MENU] key to finish.
RCU-015: Left-click the MENU box to finish.
3-3
How to access the INITIALIZE Menu with Control Unit RCU-015
1. Use the trackball to place the
pointer on the MENU box so it
is highlighted. DO NOT click
the menu box - just leave the
pointer over "MENU".
2. Press and hold down the F1
key. Keep it held down during
the next step.
3. Push the right button five times.
You should hear three beeps
on the fifth push.
The INITIALIZE menu appears.
Choose 4 INSTALLATION to
show the installation menus.
Menu operation with trackball module
1. Roll the trackball to choose the MENU box and then push
the thumbwheel or left button.
2. Spin the thumbwheel to choose menu item and then push
the thumbwheel or left button.
3. Spin the thumbwheel to choose menu option and then
push the thumbwheel or left button.
4. Left-click the MENU box to close the menu.
3-4
3.3 Adjusting Sweep Timing
Sweep timing differs with respect to the length of the signal cable between the antenna unit and
the processor unit. Adjust sweep timing to prevent the following symptoms:
• The echo of a "straight" target (for example, pier), on the 0.25 m range, will appear on the display as being pulled inward or pushed outward. See the figure below.
• The range of target echoes will also be incorrectly shown.
(1) Correct
(2) Target pushed
inward
(3) Target pushed
outward
Examples of correct and incorrect sweep timings
1. Transmit on the 0.25 nm range.
2. Adjust the radar picture controls to display picture properly.
3. Select a target echo which should be displayed straightly.
4. On the ECHO ADJ menu, On the ECHO ADJ menu, choose 4 TIMING ADJ.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
5. Spin the thumbwheel to set a suitable value which causes the target to be displayed straightly.
The setting range is 0 to 4095.
6. Left-click the MENU box to finish.
3-5
3.4 Suppressing Main Bang
If main bang appears at the screen center, suppress it as follows.
1. Transmit the radar on a long range and then wait ten minutes.
2. Adjust gain to show a slight amount of noise on the display.
3. Select the 0.25 nm range. Adjust sea clutter control to suppress sea clutter.
4. On the ECHO ADJ menu, choose 5 MBS.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
5. Spin the thumbwheel to set a suitable value so that the main bang disappears. The setting
range is 0 to 255.
6. Left-click the MENU box to finish.
3-6
3.5 Other Settings
ECHO menu setting
Open the ECHO ADJ menu as described on page 3-3 and 3-4.
[ECHO ADJ]
1 BACK
2 CABLE ATT ADJ
AUTO/MANUAL
30
3 HD ALIGN
000.0°
4 TIMING ADJ
0
5 MBS
0
6 DEFAULT ANT HEIGHT
5/7.5/10/15/20/
25/30/35/40/45/
more 50 m
7 NEAR STC CURVE
2/2.5/3/3.5
8 MID STC CURVE
3/4/5/6
9 FAR STC CURVE
6/7/8
0 RING SUPPRESSION
0
ECHO ADJ menu
CABLE ATT ADJ
Before adjusting, set the radar as follows:
IR: 2, ES: off, EAV: off, 24nm range, long pulse
(Same as default setting of PICTURE1)
To adjust the cable attenuation manually, choose MANUAL and push the thumbwheel. With
the gain set to 80, spin the thumbwheel until noise just appears on the screen. Default setting is
30 for the antenna cable length of 15 m. The setting range is 0 to 73.
To adjust the cable attenuation automatically, choose AUTO and push the thumbwheel. The
message "CABLE ATT ADJ" appears (in red) at the bottom of the screen. It takes about five minutes to complete the adjustment, after which the radar goes into stand-by.
DEFAULT ANT HEIGHT
Select height (m) of the radar antenna unit from the sea surface from among 5, 7.5, 10, 15, 20,
25, 30, 35, 40, 45 and "more 50 m".
NEAR STC CURVE, MID STC CURVE AND FAR STC CURVE
The default setting is suitable for most conditions. If necessary, change the setting according to
sea conditions.
RING SUPPRESSION
This is mainly used to removes "ring" noise that appears in the waveguide-type radar. Adjust so
the rings disappear at the range of 0.125 nm. The setting range is 0 to 255.
3-7
SCANNER menu
1. Open the INITIALIZE menu as described on page 3-3 and 3-4.
2. Choose 3 SCANNER to open the SCANNER menu.
[SCANNER]
1 BACK
2 BLIND SECTOR 1
START 000°
ANGLE 000°
3 BLIND SECTOR 2
START 000°
ANGLE 000°
4 ANT REVOLUTION
LO/HI/AUTO
5 ANT SW
OFF/ON
6 ANT STOPPED
STBY/TX
7 M SPEC
OFF/ON
8 BB TYPE
NORMAL/BB
SCANNER menu
BLIND SECTOR 1 and BLIND SECTOR 2
Set area (up to 2) where no radar pulses will be transmitted. Heading should be adjusted before
setting any blind sector. For example, set the area where an interfering object at the rear of the
antenna would produce a dead sector (area where no echoes appear) on the display. To enter an
area, enter start bearing (relative to heading) and dead sector angle. To erase the area, enter 0
for both the START and ANGLE options. The setting range of START is 0 to 359° and ANGLE is
0 to 180°.
ANT REVOLUTION
No use.
ANT SW and ANT STOPPED
This is used for antenna maintenance by service personnel.
M SPEC
No use.
BB TYPE
Choose type of radar. Select "BB" for FAR-2167DS-BB.
3-8
INSTALLATION menu
Open the INSTALLATION menu by choosing 4 INSTALLATION from the INITIALIZE menu.
RADAR
Choose main radar or sub radar.
RANGE UNIT
Choose NM, SM, km or kyd (kilo yard) as appropriate. For
the IMO- and A-type radars the range unit is fixed at "NM".
RADAR NO and RADAR POSN
For multiple radar system using the network hub, set
number (name) and antenna position for each system, to
easily distinguish radars from one another.
MODEL
Choose "60".
TYPE
Choose radar type from among the following options:
IMO: IMO compliant
A: Near-IMO specifications
B: International fishing vessels
C: Japanese flag vessels
W: Washington state (USA) ferry
[INSTALLATION]
1 BACK
2 RADAR
MAIN/SUB
3 RANGE UNIT*1
NM/SM/km/kyd
4 RADAR NO*2
1/2/3/4/5/6/7/8
5 RADAR POSN
FORE/MAIN TOP/
MAIN 2ND/MAIN 3RD/
AFT/PORT/
STARBOARD
6 MODEL
6/12/25 UP/25 DOWN/
50/30 UP/30 DOWN/60
7 TYPE
IMO/A/B/C/W
8 ON TIME
XX.XH
9 TX TIME
XX.XH
*1: Not shown on IMO- or A-type radar.
*2: No.1-4: with antenna unit
No.5-8: without antenna unit
INSTALLATION menu
ON TIME and TX TIME
These items show number of hours the radar has been turned on and transmitted, respectively.
Value can be changed; for example, after replacing magnetron TX Time can be reset to 0.
3-9
OWN SHIP INFO menu
Open the OWN SHIP INFO menu by choosing 5 OWN SHIP INFO from the INITIALIZE menu.
[OWNSHIP INFO]
1 BACK
2 LENGTH/WIDTH
LENGTH 100 m
WIDTH
50 m
3 SCANNER POSN
BOW
0m
PORT 0 m
4 GPS1 ANT POSN
BOW
0m
PORT 0 m
5 GPS2 ANT POSN
BOW
0m
LEFT 0 m
6 CONNING POSN
BOW
0m
PORT 0 m
OWN SHIP INFO menu
LENGTH/WIDTH and SCANNER POSN
To accurately inscribe own ship marker on the screen, enter length and width of the ship and
antenna position from the bow and left sides. The setting ranges are as follows:
LENGTH:
WIDTH:
BOW:
LEFT:
0 to
0 to
0 to
0 to
999 m
99 m
999 m
99 m
GPS 1 ANT POSN and GPS 2 ANT POSN
This is for AIS. Enter the GPS antenna position, from the bow and left side. The setting ranges are
the same as above.
CONNING POSN
Enter the conning position, from the bow and left side. The setting ranges are the same as those
shown on the preceding page. When you set the reference point as the conning position, these
values are used to correct the radar antenna position.
Note: If two or more radars are installed, all items on the OWN SHIP INFO menu should be the
same except 3 SCANNER.
3-10
ARPA PRESET menu
Open the ARPA PRESET menu by choosing 6 ARP PRESET from the INITIALIZE menu.
[TRACK PRESET]
[ARP PRESET]
1 BACK
2 TTM OUTPUT
OFF/REL/TRUE
3 MAX RANGE
24/32
4 ECHO LEVEL
16
5 QV DISPLAY
OFF/ON
6 ARP W/O GYRO*
OFF/ON
7 [ACQ PRESET]
8 [TRACK PRESET]
9 [ARP SENSOR DATA]
0 DEFAULT
[ACQ PRESET]
1 BACK
2 LAND SIZE
800 M
3 ANT SELECT
XN12AF/XN20AF/
XN24AF/XN4A/XN5A
SN30AF/SN36AF/
SN4A/SN5A
4 AUTO ACQ CORRE
5 SCAN
5 AUTO ACQ WEED
1 SCAN
1 BACK
2 GATE SIZE
S/ M /L/LL
3 FILTER RESPONSE
1/ 2 /3/4
4 LOST COUNT
9 SCAN
5 MAX SPEED
100 KTS
6 TRACKING MODE
1 /2/3/4
7 START TIME TGT VECT
TIME /SCAN
50 SEC
20 SCAN
*: Not shown on IMO radar.
ARP-related menus
TTM OUTPUT
Set the output format of tracked targets among OFF, REL and TRUE.
OFF:
No output
REL (relative):Target bearing from own ship, degree relative.
Target course, degree relative.
TRUE:
Target bearing, degree true.
Target course, degree true.
Note: The TTM OUTPUT port changes according to the setting for INS as described on page 313.
INS-OFF:
Output from J619 port
INS-SERIAL: Output from J620 port
INS-LAN:
Output from NETWORK port
MAX RANGE
Choose the maximum ARPA tracking range, 24 or 32 nm.
ECHO LEVEL
Set echo detection level. The setting range is 1 to 31.
QV DISPLAY
OFF: Normal picture
ON: Quantized picture. Always off at power on.
ARP W/O GYRO (Not shown on IMO radar)
ARPA may be used without a gyrocompass. Choose ON to use ARPA without a gyrocompass.
3-11
LAND SIZE
Set the minimum echo size to be considered a landmass. The setting range is 100 to 1000 m, in
increments of 100 m.
ANT SELECT
Set the model of antenna radiator used.
AUTO ACQ CORRE
Set the number of consecutive echoes to receive from a target before initiating automatic acquisition on it. The setting range is 3 to 10.
AUTO ACQ WEED
Set the number of consecutive "no echoes" from a target before canceling automatic acquisition
on it. The setting range is 1 to 5.
GATE SIZE
Set the gate size among S, M, L, or LL.
FILTER RESPONSE
Set the filter response function. The setting range is 1 to 4. Choose 1 for better trackability; 4 for
better stability.
LOST COUNT
Set the number of consecutive "no echoes" before an acquired target is declared as a lost target.
The setting range is 1 to 20.
MAX SPEED
Set the maximum tracking speed. The setting range is 40 to 150.
TRACKING MODE
Set the tracking mode among 1 to 4.
START TIME TGT VECT
Choose how to wait from time of acquisition to display of vector. Choose TIME to set by time (seconds) or SCAN to set by number of antenna scans.
3-12
OTHER menu
Open the OTHER menu by choosing 8 OTHERS from the INITIALIZE menu.
[OTHERS]
1 BACK
2 DEMO ECHO
OFF/EG/SPU/PC
3 EAV w/o GYRO
OFF/ON
4 ARP SELECT
ARPA/ATA
5 INS
OFF/SERIAL/LAN
OTHER menu
EAV w/o GYRO
Echo averaging can be used without a gyrocompass. Choose ON to use echo averaging without
a gyrocompass.
ARP SELECT
Choose ARPA or ATA depending on your radar system.
INS
Choose appropriate item according to the ECDIS connected.
OFF:
No connection
SERIAL: When connecting FEA-2105 series ECDIS.
LAN:
When connecting FEA-2107 series ECDIS.
3-13
This page intentionally left blank.
3-14
4. OPTIONAL EQUIPMENT
4.1 Gyro Converter GC-10
The Gyro Converter GC-10, incorporated inside the processor unit, converts analog gyrocompass
reading into digital coded bearing data for display on the radar screen.
This section explains how to install the GC-10 (mainly consisting of the GYRO CONVERTER
board) and set it up according to the gyrocompass connected.
Installing the GYRO CONVERTER board
Necessary Parts: Gyro Converter GC-10-2 (Code no. 000-080-440)
See packing list at the back of this manual for details.
1
3
1
12
3
1
4
1. Open the processor unit.
2
1
1
12
1
1
1
5
1
1
3
7
Processor unit, inside view
4-1
2. Fasten the GYRO CONVERTER board inside the processor unit with five washer head screws.
3. Fix connector 231-607/019-FUR (called J602) with two screws.
Screw
M3X8 5 pcs
GYRO CONVERTER board
64P1106A
Screw
M2.6X10 2 pcs
1
7
Connector (231)
231-107/026-FUR
7
1
Connector (231)
231-607/019-FUR
PCB 03P9342
Fixing GYRO CONVERTER board inside the processor unit
4. Connect the GYRO CONVERTER board to the 03P9342 board with XH-PH 03-2088 connector
assy. (6-14P) and NH connector assy. 03-2091.
4-2
5. Connect J602 (attached at step 3) to the GYRO CONVERTER board with two VH connector
assemblies 03-2089 (3P) and 03-2090 (5P).
Wiring WAGO connector
Press downward.
Terminal opener
Connection for J602
2
J602
P608
1 2 3 4
7 6 5 4 3 2 1
PPL
BLU
GRN
YEL
ORG
From J5 RED
BRN
From J4
Connection for P608
1
YEL
ORG
RED
BRN
WAGO connector
Twist
2
2
Wire
Procedure
1. Twist core.
2. Press terminal opener downward.
3. Insert wire to hole.
4. Remove terminal opener.
5. Pull wire to confirm that it is secure.
VH connector assy.
03-2089 (5P)
VH connector assy.
03-2090 (3P)
P5
1
To J602
XH-PH connector assy.
03-2088 (6-14P)
To P608
P7
P4
NH connector assy.
03-2091 (5P)
P1
P603
J5
4
GYRO CONVERTER J1
64P1106A
1
3
P608
3
1
J7
1
1
12
1
5
J602
1
2
1
7
J603
1
12
1
J4
TB
03P9342
Connecting connector assemblies inside processor unit
6. Confirm gyrocompass specifications and set up the DIP switches and jumper wires on the
GYRO CONVERTER board according to gyrocompass connected:
• Setting jumper wires and DIP switches by gyrocompass specifications: page 4-6
• Setting jumper wires and DIP switches by make and model of gyrocompass: page 4-7
• Location of jumper wires and DIP switches: page 4-8
4-3
7. Pass the gyrocompass cable through the cable clamp and connect it to connector J602 as
shown in the figure below.
8. Attach the clamps to the plastic cover and then attach the cover to the GYRO CONVERTER
board as shown in the figure below. Pass cables thru the clamp ED-1.
Screw
M4X8 3 pcs
Plastic cover
Clamp CKS-10-L
Clamp EDS-1
Insert cables to these
clamp.
2
1
12
1
1
1
5
1
1
1
7
3
1
3
1
12
3
1
4
Clamp CKS-13-L
Attaching plastic cover for GYRO CONVERTER board
9. Close the processor unit.
4-4
Connection of external power supply
An external power supply is necessary when the repeater signal is step-by-step type and the step
voltage is below 20 V or output voltage is less than 5 W.
1. Cut jumper wire JP1 on the GYRO CONVERTER board when an external power supply is
used.
2. Connect the gyrocompass cable and power cable as shown below.
GYRO CONVERTER board
[A] 64P1106
External Power Supply
20 - 135 VAC
20 - 100 VDC
J5
1 > R2
2 > R1/COM
Either connection
in case of DC
polarity.
S2
J4
1 > S1
2 > S2
S3
3 > S3
S1
Gyrocompass
(Step type)
COM
F.G.
4>T
5 > F.G.
Connection of external power supply to GYRO CONVERTER board
DIP switch, jumper wire settings
Default setting
The gyro converter GC-10 is set at the factory for connection with the gyrocompass specifications
below.
AC synchronous signal:50/60 Hz
Rotor voltage:
60 V to 135 V AC
Stator voltage:
60 V to 135 V AC
Gear ratio:
360x
Supply voltage:
30 V to 135 V AC
If the specifications of the gyrocompass differ from those mentioned above, change jumper wire
and DIP switch settings on the GYRO CONVERTER board. Settings may be changed according
to gyrocompass specifications (see page 4-6) or make and model of gyrocompass (see page 47). For the location of DIP switches and jumper wires, see page 4-8.
Note: If you change the setting with the power turned on, set #8 of SW2 from OFF to ON, then
OFF again to effect changes.
4-5
Setting method 1: DIP switch settings and gyrocompass specifications
1) Gyrocompass type
2) Frequency
50/60 Hz
SW
1-7
OFF
SW
1-8
OFF
#2, #3, #4
400 Hz
ON
OFF
OFF
#4, #5, #6
500 Hz
OFF
ON
ON
OFF
#4, #5, #6
DC
ON
ON
ON
OFF
#4, #5, #6
Gyrocompass
type
AC synchronous
SW
1-4
OFF
SW
1-5
OFF
SW
1-6
OFF
#1, #2, #3
DC synchronous
OFF
OFF
OFF
DC step
ON
OFF
Full-wave
pulsating current
Half-wave
pulsating current
OFF
ON
JP1
3) Rotor voltage (between R1 & R2)
Rotor Voltage
20 to 45 VAC
30 to 70 VAC
40 to 90 VAC
60 to 135 VAC
SW2-1
ON
OFF
ON
OFF
Remarks
AC synchronouspulsating current
AC synchronouspulsating current
AC synchronouspulsating current
DC synchronous
DC step
4) Stator voltage (between S1 & S2)
JP3
#2
#2
#1
#1
5) Ratio
Ratio
360X
180X
90X
36X
Frequency
Stator Voltage
SW2-2
20 to 45 VAC, or 20 to 60 VDC
ON
30 to 70 VAC, or 40 to 100 VDC OFF
40 to 90 VAC
ON
60 to 135 VAC
OFF
SW2-3
OFF
OFF
OFF
OFF
JP2
#2
#2
#1
#1
6) Supply voltage
SW1-1
OFF
ON
OFF
ON
SW1-2
OFF
OFF
ON
ON
SW1-3
OFF
OFF
OFF
OFF
7) AD-10 format data
Select data Tx interval for ports 1 to 6 with
jumper wires JP6 and JP7. The Tx interval
is available in 25 msec or 200 msec. Use
25 msec for radar.
9) NMEA-0183
Version no.
Version no. SW3-1
1.5
OFF
2.0
ON
Stator Voltage
20 to 45 VAC, or 20 to 60 VDC
30 to 70 VAC, or 40 to 100 VDC
JP4
#2
#1
JP5
#2
#1
8) NMEA-0183 Tx interval and output sentence
Tx
interval
SW
2-5
SW
2-6
1s
OFF
OFF
HDT+VHW
200 ms
ON
OFF
HDT
100 ms
OFF
ON
HDT
25 ms
ON
ON
HDT
10) NMEA-0183
baud rate
Baud rate SW3-2
4800 bps
OFF
38400 bps
ON
11) Power fail
detection
Talker
SW3-3
Disable
OFF
Enable
ON
Output sentence
12) Stator signal
loss detection
Detection
SW2-7
Yes
OFF
No
ON
(Use OFF for radar only)
SW2-4: factory use only
SW3-4: not used
After setting jumpers and DIP switches, reset the power or set SW2-8 to “CPU”.
4-6
Setting method 2: by make and model of gyrocompass
Maker
Models
Specification
SW
1-1
SW
1-2
SW
1-3
SW
1-4
SW
1-5
SW
1-6
SW
1-7
SW
1-8
SW
2-1
SW
2-2
SW
2-3
JP 1
JP 2
JP 3
JP 4
JP 5
Anschutz
Standard 2,3
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 22V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
#1,
#2,#3
#2
#2
#1
1
#
Standard 4,6
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 90V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#2
#1
#1
1
#
Standard 20
DC step
35V 180x
COM(-) ,3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
2
#
C-1/1A/2/3
A-55, B-55
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 22V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
#1,
#2,#3
#2
#2
#1
1
#
CMZ-700
DC step
24V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF Remove
#2
-
*
*
DC synchronous 360x
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
-
ON
OFF
Remove
#2
-
*
*
DC step
35V 180x
COM(+),3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
AC synchronous
50/60Hz
Rotor voltage: 100V
Stator voltage: 90V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
step
35V 180x
See note below. COM(+),3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
Remove
#2
-
*
*
Plath
NAVGAT II/III
AC synchronous
50/60Hz
Rotor voltage: 50/60V
Stator voltage: 68V
360x
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#2
#2
#1
#1
Tokimec
(Sperry
type)
ES-1/2/11
GLT-101/102/
103/106K/107
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 90V
36x
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
ES-11A/110
TG-200
PR222R/2000
PR237L/H
GM 21
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 22V
90x
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
MK-14
MOD-1/2/T
NK-EN,NK-EI
DC step
70V 180x
COM(-), 3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
SR-130/140
DC step
70V 180x
5-wire, open collector
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
TG-100/5000
PR-357/130/
140, ES-17
GLT-201/202
/203
DC step
70V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
TG-6000
DC step
24V 180x
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
GM-11
AC synchronous
50/60Hz
Rotor voltage: 100V
Stator voltage: 90V
90x
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
SR-120,ES-16
MK-10/20/30
DC step
35V 180x
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
Kawasaki
GX-81
AC synchronous
50/60Hz
Rotor voltage: 100/110V
Stator voltage: 90V
90x
OFF
ON
OFF OFF
OFF
OFF
OFF
OFF
OFF
#1,
#2,#3
#1
#1
#1
#1
Armabrown
MK-10,MKL-1
SERIES1351,
MOD-4
DC step
50V 180x
COM(+), 3-wire(-)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
OFF
OFF
#4,
#5,#6
#2
-
#1
#1
Robertson
SKR-80
DC step
35V 180x
COM(-), 3-wire(+)
ON
OFF
OFF
ON
OFF
OFF
ON
ON
-
ON
OFF
#4,
#5,#6
#2
-
#2
#2
Yokogawa
Navtec
(Pla th
type)
CMZ-250X/
300X/500
CMZ-100/200/
300
C-1Jr,D-1Z/1/3
IPS-2/3
CMZ-50
OFF
OFF
*: Set JP4 and JP5 according to the voltage of the external power supply.
Note: If CMZ-50 has 35 VDC, set JP1 to #4, #5, #6.
4-7
Location of DIP switches, jumper wires on the GYRO CONVERTER board
JP5, JP4
(Supply voltage)
JP2
(Stator voltage)
JP3
(Rotor voltage)
64P1106
JP1
(Gyro type)
SW3
DIP switch
J12
(Data output
port #6)
J11
(Data output
port #5)
J10
(Data output
port #4)
SW2
DIP switch
Fuse
(2A)
SW1
J4
DIP switch
(Stator signal input)
J5
(Rotor signal input,
external power input)
J6
(IEC-61162-1 output port)
GYRO CONVERTER board
4-8
JP6, JP7
(AD format
data Tx interval)
J9
(Data output port #3)
J8
(Data output port #2)
J7
(Data output port #1)
Setting the heading readout on the radar display
Confirm that the gyrocompass is giving a reliable readout. Then, set the heading readout on the
radar display with the gyrocompass readout as follows:
1. Right-click the HDG box at the top right corner on the screen.
[HDG MENU]
1 HDG SOURCE
AD-10/SERIAL
2 GC-10 SETTING
000.0˚
HDG menu
2. Spin the thumbwheel to choose 1 HDG SOURCE and push the left button.
3. Spin the thumbwheel to choose AD-10 and push the left button.
4. Spin the thumbwheel to choose 2 GC-10 SETTING and push the left button.
5. Spin the thumbwheel to set gyrocompass reading and push the left button.
6. Push the right button close the menu.
4-9
4.2 Memory Card Interface Unit
Mounting considerations
When selecting a mounting location, observe the following points:
•
•
•
•
Locate the unit away from heat sources because of heat that can build up inside the cabinet.
Locate the unit away from places subject to water splash and rain.
Leave sufficient space at the sides and rear of the unit to facilitate maintenance.
A magnetic compass will be affected if the unit is placed too close to the magnetic compass.
Observe the compass safe distances on page ii to prevent interference to a magnetic compass.
Mounting procedure
Flush mounting
This unit can be flush-mounted in a panel with the standard installation materials.
1. Prepare a cutout in the mounting location, referring to the outline drawing at the end of this
manual.
2. Screw in the threaded rods to the flange on the front panel of the unit securely by hands.
3. Set the unit to the cutout.
4. Insert the flat washer, spring washer and nut in that order for each rod and fasten the nuts.
Flush mounting dimensions for memory card interface unit
4-10
Desktop mount
Requires the optional desktop mount kit FP03-10201. Refer to the packing list at the back of this
manual for further information about this kit.
1. Fix the mounting bracket 19-023-3081 to the unit with four screws.
2. Mount the above assembly on a desktop with four self-tapping screws.
Connections
One memory card IF unit and one processor unit
Connect as shown below.
Processor unit
J614
12 VDC
MJ-A3SPF0015-100 (10 m)
Memory card IF unit
12 VDC
two mini-cards
PSE-4PTX-BL (10 m)
NETWORK
NETWORK
RJ-45
Connections one memory card interface unit
One memory card IF unit and multiple processor units
Prepare optional armored LAN cable kit and Switching Hub HUB-100. Connect as shown below.
No.1
J614
Processor
unit
NETWORK
12 VDC
MJ-A3SPF0015-100 (10 m)
Memory card IF unit
12 VDC
FR-FTPC-CY (10/20/30 m)
(straight)
two mini-cards
NETWORK
FR-FTPC-CY (10/20/30 m)
(straight)
No.2
Processor
unit
No.3
Processor
unit
No.4
Processor
unit
Switching hub
FR-FTPC-CY
(10/20/30 m)
(straight)
HUB-100
(option)
FR-FTPC-CY (10/20/30 m) (straight)
FR-FTPC-CY (10/20/30 m) (straight)
Connecting one memory card interface unit and multiple processor units via switching hub
4-11
Armored LAN cable kit
Type
Code No.
Contents
OP03-28900
000-082-658
Cable FR-FTPC-CY (10 m), Modular connector (2 pcs.)
OP03-28910
000-082-689
Cable FR-FTPC-CY (20 m), Modular connector. (2 pcs.)
OP03-28920
000-082-660
Cable FR-FTPC-CY (30 m), Modular connector (2 pcs.)
Note: When two memory card interface units are connected via a network, change ID code for the
second unit.
1. Remove the cover and set the IP0 bit of the DIP switch S1 on the CARDCPU board (03P9333)
to ON.
2. Set INIT bit of S1 to ON and turn on the radar. Wait until CR2 starts blinking. DO NOT turn off
the power until CR2 starts blinking.
3. Turn off the power and set INIT bit to OFF.
ON
J314
OFF
IP0
IP1
IP2
CR2
S1
INIT
(Default: all OFF)
CARDCPU board 03P9333
Memory card interface unit, showing location of DIP switch S1
4-12
4.3 DVI-RGB Conversion Kit
This information provides the procedure necessary for the installation of the DVI-RGB conversion
kit. This kit is installed in the processor unit to enable connection of an RGB monitor or VDR
(Voyage Data Recorder).
Name:
DVI-RGB conversion kit
Type:
OP03-180-2
Code no.: 008-536-070
See packing list for contents. Refer to the figure below for modification.
DVI-RGB CONVERSION board
(SLB-FRN4-A)
DVI cable
M3x8
6 pcs
J9
(10 pin)
J4
(6 pin)
J3
J615
03-2094
03-2092
03P9342 board
03-2093
Spacer
SQ-35
6 pcs
M3x8
4 pcs
J1
(13 pin)
RGB-BUFF board
(03P9229B)
D-sub 15P
Female
J2
J3
(3 pin)
RGB Cable
(User supply)
Spring washer
Fixing
holes
Boss
Ferrite core
To external monitor or
BNC connector converter
(see page 4-15).
Clamp copper tape
section by cable clamp.
Ferrite core side: Connect to DVI-D port on
the upper part of the processor unit.
How to wire the DVI-RBG conversion board
4-13
1. Remove the top cover and open the upper part of the processor unit.
DVI-D port
(Connect DVI cable at step 12.)
Processor unit, side view
2. Fix the RGB-BUFF board (03P9229B board) with four screws. (See the figure below.)
3. Attach the connector assemblies to J1 and J3 on the 03P9229B board as follows.
J1: 13-pin connector of the connector assembly 03-2094
J3: 3-pin connector of the connector assembly 03-2093
4. Attach six sets of spring washers and spacers at the locations shown below.
Spring washer, spacer
J1
03P9229B board
J2 (Connect RGB Cable at step 10.)
J3
J2
03P9342 board
J615 (Connect connector assembies at step 8.)
Processor unit (bottom chassis)
4-14
5. Attach the DVI-RGB CONVERSION board to the location shown below.
DVI-RGB
CONVERSION board
J3 (Connect DVI cable at step 9.)
J9
J4
Fixing the DVI-RGB conversion board inside the processor unit
6. Attach the 10-pin connector from J1 on the 03P9229B board to J9 on the DVI-RGB board.
7. Attach the connector assembly 03-2092 to J4 on the DVI-RGB CONVERSION board.
8. Remove connector housing J615 from the 03P9342 board. Connect the cable from J3 on the
03P9229B board and the cable from J4 on the DVI-RGB CONVERSION board to J615. Attach
J615 to the 03P9342 board.
To connect wires to the WAGO connector, use the terminal opener (supplied as installation
materials) as shown below.
Terminal opener
J615 Housing
1) Press downward.
1
2
BRN
RED
ORG
YEL
GRN
3
4
5
2) Insert core.
Connecting wires to the housing
9. Connect the DVI cable to J3 on the DVI-RGB CONVERSION board. Connect the end that does
not have the ferrite core.
10.Pass an RGB cable (local supply) through the cable clamp and connect it to J2 on the
03P9229B board.
11.Pass the DVI cable through the cable clamp, laying the section with copper tape in the cable
clamp.
12.Assemble the processor unit and connect the other end of the DVI cable to the DVI-D port.
4-15
4.4 BNC Connector Converter
To connect the FURUNO Voyage Data Recorder VR-5000 to this radar, the DVI-RGB conversion
kit (mentioned at previous paragraph) and the BNC connector converter are required. Also VGA
cable (between the processor unit and the BNC connector converter) and five 75 ohm coaxial
cables (between the BNC connector converter and VR-5000) are required.
FAR-2167DS(-BB)
PROCESSOR UNIT
BNC CONNECTOR
R
CONVERTER
DSUB-BNC-1
G
VGA cable
DVI-RGB
Conversion kit
D-sub 15P
Female
D-sub 15P
Male
75 W coax. cable
VD1
R
VR-5000
DATA COLLECTING
UNIT
G
B
B
H
HS
V
VS
Connecting VR-5000 to FAR-2167DS(-BB) via BNC connector converter
BNC connector converter
4-16
5. IO DATA
Available input and output data are shown in the tables below and input and output sentences are
shown on the next page.
Note: This radar accepts position data fixed by WGS-84 geodetic datum only. Set the datum to
WGS-84 on the EPFS (GPS, etc.) connected to this radar. If other type of datum is input, the error
message "DATUM" appears and the AIS feature is inoperative.
Input
Data
Heading
signal
Specifications
Contents
Synchro or step
GC-10 required
AD-10 format
External AD-100
Remarks
Switching between AD-10
and IEC 61162 is done
from menu.
IEC 61162-2
Speed signal
IEC 61162-1
Navigator
data
IEC 61162-1
Position, course, speed, LORANC TD, waypoint, route, time, wind
speed and direction, current data,
depth, water temperature, roll,
pitch, ROT
External
radar signal
Heading, Bearing,
Trigger, Video
No GAIN, STC control
Alarm ACK
input
Contact closure
signal
Operate as remote display
Input signal from alarm
system
Track Control RS-422
unit
Option
Output
Data
Specifications
Contents
Remarks
Radar system
data
RS-232C
RSD, OSD, TLL
For PC plotter
ARPA data
IEC 61162-1
TTM
For ECDIS
Remote display
signal
Heading, Bearing, Tx
Trigger, Video
External LCD
monitor signal
DVI
Same as main monitor unit
2 systems max.
External CRT
monitor signal
R, G, B, H, V
Same as main monitor unit
Option
Alarm signal
Contact closure
signal
Output to alarm system by using
photo-relay
4 outputs, output
content selected from
menu.
2 ports
5-1
IEC 61162 input sentence and priority
Item
Sentence and order of priority
Speed (STW)
Speed (SOG
Speed (position)
Heading (True)
Position
Waypoint
Date
Depth
Water temperature
Wind
VBW>VHW
VBW
VTG>RMC
HDT*
GGA>GLL>RMC>RMABWR>BWC>RM
B
ZDA
DPT>DBT>DBS
MTW
MWV
IEC 61162 output sentence
Item
Target L/L
Radar system data
Own ship data
ARPA target data
Sentence
TLL (Not on IMO radar)
RSD
OSD
TTM
HDT is IEC61162-2, all other sentences are IEC61162-1 ed2.
5-2
+056#..#6+10/#6'4+#.5
#%%'5514+'5
70+6
176.+0'
):: %2
(2
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
)::
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
45$545$5
&'5%4+26+10%1&'ͳ
䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
#%%'5514+'5
ઃዻຠ
ઃዻຠ
#06'00#&4+8'70+6
ⓨਛ✢ᧄ૕ㇱ⚵ຠ
࡙࠾࠶࠻
0#/'
45$545$5
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
A-1
*':$1.6
౐ⷺ㩘㩨㩣㩎‫ޓ‬㧔ో㩒㩆㩨㧕
*':076
౐ⷺ㩏㨹㩎‫ޓ‬㧝⒳
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
14+0)
1㩢㩧㩂㩨
%4+/210.7)
࿶⌕┵ሶ
%4+/210.7)
࿶⌕┵ሶ
6'4/+0#.12'0'4
ᠲ૞㩤㩔㩨㨺
%14415+102411(
47$$'4/#6
㒐ⲁࠧࡓ
5'#.9#5*'4
㩆㨺㩣㩦㨹㩆㨶
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01 /:575
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
%1&'01
,$#)
%1&'01
(8
%1&'01
(8㨻㨿
%1&'01
%1&'01
%1&'01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
%2
6;2'
↪ㅜ㧛஻⠨
4'/#4-5
):: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)::
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-2
)4170&+0)9+4'
㨻㨺㩇✢
*':$1.6
౐ⷺ㩘㩨㩣㩎
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
*':076
౐ⷺ㩏㨹㩎‫ޓ‬㧝⒳
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
495
%1&'01 /:575
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
%2
6;2'
↪ㅜ㧛஻⠨
4'/#4-5
):: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)::
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-3
2
1
番 号
NO.
略 図
OUTLINE
100-090-720
100-090-730
2
2
数量
Q'TY
1/1
03GO-X-9501
用途/備考
REMARKS
03GO-X-9501 -0
FURUNO ELECTRIC CO .,LTD.
CODE NO.
03-015-3234-0
CODE NO.
03-015-3233-0
型名/規格
DESCRIPTIONS
FP03-10101
TYPE
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
COLLAR FOR LIFTING
FIXTURE
取付用カラー
LIFTING FIXTURE
つり上げ金具
名 称
NAME
ACCESSORIES
付属品表
008-538-730
CODE NO.
A-4
N A M E
O U T L I N E
ANTENNA INSTALLATION MATERIALS
UNIT
008-254-590
SN5AF/7AF/30AF/36AF
008-505-950 **
SN30AF
DESCRIPTION/CODE №
(略図の寸法は、参考値です。
03FT-X-9851
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
1.䍘-䍢䍼⇟ภᧃየ䈱[**]䈲䇮ㆬᛯຠ䈱ઍ⴫ဳᑼ/䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
INSTALLATION MATERIALS
工事材料
アンテナ工材
ANTENNA
アンテナ組品
ユニット
SN30AF/SN36AF
PACKING LIST
03FT-X-9851 -0
1
1
Q'TY
1/1
A-5
⇟ภ
01
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%1&'01
59㨻㩣㩚㩋㨷㨺㩖㩨)
%1&'01
/:575
%1&'01
/575‫ޓ‬
%1&'01
/575
%1&'01
,$#)
%1&'01
50#(#(#(/5##(#(
ᢙ㊂
36;
%3:
↪ㅜ㧛஻⠨
4'/#4-5
%3: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
5+.+%1047$$'4
㩃㩚㩆㨺㩣
*':$1.6
౐ⷺ㩘㩨㩣㩎
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
14+0)
1㩢㩧㩂㩨
)7+&'2+0
㩕㩩㩧
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
6;2'
%1&'01
A-6
⇟ภ
01
%#$.'
㩃㨺㩖㩨㩣
%
%#$.'
㩃㨺㩖㩨㩣
%
%#$.'
㩃㨺㩖㩨㩣
%
%#$.'
㩃㨺㩖㩨㩣
%
⇛‫ޓޓ‬࿑
176.+0'
(#4UGTKGU
%1&'01
49/
%1&'01
49/
%1&'01
49/
%1&'01
49/
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
).:
ㆬᛯ‫ޓ‬61$'5'.'%6'&
ାภ㩃㨺㩖㩨㩣‫ޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
ାภ㩃㨺㩖㩨㩣‫ޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
ାภ㩃㨺㩖㩨㩣‫ޓޓ‬
5+)0#.%#$.'
ㆬᛯ‫ޓ‬61$'5'.'%6'&
ାภ㩃㨺㩖㩨㩣‫ޓޓ‬
5+)0#.%#$.'
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
6;2'
%1&'01
A-7
N A M E
O U T L I N E
OTHER INSTALLATION MATERIALS
ACCESSORIES
SPARE PARTS
SPARE PARTS
UNIT
(略図の寸法は、参考値です。
000-149-054
DVI-D/D SINGLELINK 5M
008-536-010
FP03-09810
008-535-990
SP03-14401
000-081-063
SP03-03900
000-080-288 **
MU-201CR
DESCRIPTION/CODE №
03GL-X-9855
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
2.੍஻ຠ䈲䇮AC↪,DC↪䈪ㆬᛯ㗿䈇䉁䈜䇯
CHOOSE SPARE PARTS DEPENDING ON AC OR DC POWER.
1.䍘䍎䍢䍼ᧃየ䈮[**]䈱ઃ䈇䈢䍳䍤䍍䍢䈲ઍ⴫䈱ဳᑼ/䍘䍎䍢䍼䉕⴫␜䈚䈩䈇䉁䈜䇯
DOUBLE ASTERISK DENOTES COMMONLY USED EQUIPMENT.
CABLE ASSY.
ケーブル組品
その他工材
ACCESSORIES
付属品
付属品
SPARE PARTS
予備品
予備品
SPARE PARTS
予備品
予備品
DISPLAY UNIT
表示部
ユニット
MU-201CR
PACKING LIST
03GL-X-9855 -2
1
1
AC用
1
DC用
1
1
Q'TY
1/1
A-8
⇟ภ
01
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
:575
%1&'01
%1&'01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
6;2'
ᢙ㊂
36;
).:
⴫␜ㇱ↪‫ޓޓޓޓޓޓ‬
(14&+52.#;70+6
⴫␜ㇱ↪‫ޓޓޓޓޓޓ‬
(14&+52.#;70+6
⴫␜ㇱ↪‫ޓޓޓޓޓޓ‬
(14&+52.#;70+6
↪ㅜ㧛஻⠨
4'/#4-5
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
5'.(6#22+0)5%4'9
㩎㩡㩇㩊㨹㩕㩩㩧㩒㩆㩨‫ޓ‬⒳
2#0'.*11-
㩔㩩㩒㩣㩖㨹㩂
%15/'6+%%#2
㩔㩩㩒㩣㩀㩔㩨㨺
ฬ‫ޓޓ‬⒓
0#/'
#%%'5514+'5
ઃዻຠ⴫
%1&'01
A-9
㩕㨷㨺㩇㩨
(75'
()/$#8
()/$8#
2$(
2'4
8'5
⴫␜ㇱ↪
(14&+52.#;70+6
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪ
ᄌࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
5'652'4
8'55'.
4'/#4-5%1&'01
).:
52#4'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52
6;2'
&9)01
14
6;2'01
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
).: $1:012
%1&'01
A-10
0#/'
࡙࠾࠶࠻
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
176.+0'
427
&'5%4+26+10%1&'ͳ
36;
70+6
0#/'
176.+0'
ขᛒ⺑᣿ᦠ
೙ᓮㇱ
427
241%'551470+6
੍஻ຠ
).: &'5%4+26+10%1&'ͳ
36;
1/
12'4#6145/#07#.
㩿㪁㪊㪀
ⵝ஻ⷐ㗔ᦠ
52#4'2#465
+/
+056#..#6+10/#07#.
੍஻ຠ
52
52#4'2#465
ᠲ૞ⷐ㗔ᦠ
15
㩿㪁㪈㪀
੍஻ຠ
12'4#6145)7+&'
52
52#4'2#465
㩿㪁㪈㪀
੍஻ຠ
52
52#4'2#465
㩿㪁㪈㪀
Ꮏ੐᧚ᢱ
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
%2
+056#..#6+10/#6'4+#.5
㩿㪁㪉㪀
Ꮏ੐᧚ᢱ
%2
+056#..#6+10/#6'4+#.5
㩿㪁㪉㪀
࿑ᦠ
&1%7/'06
ขᛒ⺑᣿ᦠ
1/
12'4#6145/#07#.
㪈㪅䍘㪄䍢䍼⇟ภᧃየ䈱㪲㪁㪁㪴䈲䇮ㆬᛯຠ䈱ઍ⴫䍘䍎䍢䍼䉕⴫䈚䉁䈜䇯
㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪜㪥㪛㪠㪥㪞㩷㪮㪠㪫㪟㩷㩹㪁㪁㩹㩷㪠㪥㪛㪠㪚㪘㪫㪜㪪㩷㪫㪟㪜㩷㪚㪦㪛㪜㩷㪥㪬㪤㪙㪜㪩㩷㪦㪝㩷㪩㪜㪧㪩㪜㪪㪜㪥㪫㪘㪫㪠㪭㪜㩷㪤㪘㪫㪜㪩㪠㪘㪣㪅
㪊㪅㩿㪁㪊㪀㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪઀᭽䈱ᤨ䈱䉂ᷝઃ䈘䉏䉁䈜䇯
㪪㪬㪧㪧㪣㪰㪜㪛㩷㪮㪠㪫㪟㩷㪝㪘㪩㪄㪉㪈㪌㪎㪆㪉㪈㪍㪎㪛㪪㩷㪦㪥㪣㪰㪅
ဳᑼ䎒䱤䱚䱮䲈⇟ภ䬛䯾Ბ䬽႐ว䫺ਅᲑ䭗䭙਄Ბ䬺ઍ䭞䭚ㆊᷰᦼຠ䬶䬑䭙䫺䬸䬰䭘䬚䬛౉䬲䬵䬓䭍䬨䫻䫹䬹䬙䫺ຠ⾰䬾ᄌ䭞䭙䭍䬪䭢䫻
A-11
㪉㪅䋨㪁㪈䋩䋨㪁㪉䋩䈲䇮䈠䉏䈡䉏઀᭽ㆬᛯຠ䉕⴫䈚䉁䈜䇯
䋨㪁㪈䋩䋨㪁㪉䋩㪠㪥㪛㪠㪚㪘㪫㪜㩷㪪㪧㪜㪚㪠㪝㪠㪚㪘㪫㪠㪦㪥㩷㪪㪜㪣㪜㪚㪫㪠㪭㪜㩷㪠㪫㪜㪤㪅
䎷䎺䎲䎃䎷䎼䎳䎨䎶䎃䎤䎱䎧䎃䎦䎲䎧䎨䎶䎃䎰䎤䎼䎃䎥䎨䎃䎯䎬䎶䎷䎨䎧䎃䎩䎲䎵䎃䎤䎱䎃䎬䎷䎨䎰䎑䎃䎃䎷䎫䎨䎃䎯䎲䎺䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎃䎰䎤䎼䎃䎥䎨䎃䎶䎫䎬䎳䎳䎨䎧䎃䎬䎱䎃䎳䎯䎤䎦䎨䎃䎲䎩䎃䎷䎫䎨䎃
䎸䎳䎳䎨䎵䎃䎳䎵䎲䎧䎸䎦䎷䎑䎃䎴䎸䎤䎯䎬䎷䎼䎃䎬䎶䎃䎷䎫䎨䎃䎶䎤䎰䎨䎑
).:
䯴⇛࿑䬽ኸᴺ䬾䫺ෳ⠨୯䬶䬨䫻䎃䎧䎬䎰䎨䎱䎶䎬䎲䎱䎶䎃䎬䎱䎃䎧䎵䎤䎺䎬䎱䎪䎃䎩䎲䎵䎃䎵䎨䎩䎨䎵䎨䎱䎦䎨䎃䎲䎱䎯䎼䎑䯵
3
2
1
CRIMP-ON LUG
圧着端子
AC用
略 図
OUTLINE
000-538-118
000-147-417
000-808-981
FURUNO ELECTRIC CO .,LTD.
CODE NO.
FV2-4 アオ
CODE NO.
734-230
CODE NO.
231-131
型名/規格
DESCRIPTIONS
CP03-25602
TYPE
数量
Q'TY
2
1
1
03GL-X-9405
制御部用 FOR PROCESSOR UNIT
制御部用 FOR PROCESSOR UNIT
1/1
制御部用 FOR PROCESSOR UNIT
用途/備考
REMARKS
03GL-X-9405 -0
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
TERMINAL OPENER
操作レバー
TERMINAL OPENER
操作レバー
名 称
NAME
INSTALLATION MATERIALS
番 号
NO.
工事材料表
008-535-940
CODE NO.
A-12
㩕㨷㨺㩇㩨
(75'
()$18
#2$(
2'4
8'5
(75'
㩕㨷㨺㩇㩨
()$18#
2$(
&9)01
14
6;2'01
2'4
8'5
#%↪‫ޓޓޓޓޓޓޓޓ‬
(14241%'551470+6
).:
52#4'
4'/#4-5%1&'01
5'652'4
8'55'.
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌ
ࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
).: $1:012
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
52
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪ
ᄌࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
#%↪‫ޓޓޓޓޓޓޓޓ‬
(14241%'551470+6
).:
52#4'
4'/#4-5%1&'01
5'652'4
8'55'.
6;2'
%1&'01
A-14
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52
6;2'
&9)01
14
6;2'01
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
).: $1:012
%1&'01
A-13
+056#..#6+10/#6'4+#.5
52#4'2#465
70+6
176.+0'
%2
52
52
257
&'5%4+26+10%1&'ͳ
36;
A-15
):: 䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
)::
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
䋨㪁㪈䋩䈱੍஻ຠ䈲㪃઀᭽䈮䉋䉍㪘㪚㪈㪇㪇↪㪑㪪㪧㪇㪊㪄㪈㪌㪌㪇㪈㪃㪘㪚㪉㪉㪇↪䋺㪪㪧㪇㪊㪄㪈㪌㪌㪇㪉㪅
㪁㪈㩷㪑㩷㪪㪜㪣㪜㪚㪫㩷㪦㪥㪜㩷㪘㪚㪚㪦㪩㪛㪠㪥㪞㩷㪫㪦㩷㪧㪩㪦㪚㪜㪪㪪㪦㪩㩷㪬㪥㪠㪫㩾㪪㩷㪪㪧㪜㪚㪠㪝㪠㪚㪘㪫㪠㪦㪥㪪㩷㪑㩷㪪㪧㪇㪊㪄㪈㪌㪌㪇㪈㩷㪝㪦㪩㩷㪈㪇㪇㪭㪘㪚㩷㪦㪩㩷㪪㪧㪇㪊㪄㪈㪌㪌㪇㪉㩷㪝㪦㪩㩷㪉㪉㪇㪭㪘㪚
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
52#4'2#465
੍஻ຠ
52#4'2#465
੍஻ຠ
੍஻ຠ
219'4%10641.70+6
㔚Ḯ೙ᓮㇱ
࡙࠾࠶࠻
0#/'
257
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
%4+/210.7)
࿶⌕┵ሶ
ฬ‫ޓޓ‬⒓
0#/'
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
(8㨻㨿
ဳฬ㧛ⷙᩰ
&'5%4+26+105
ᢙ㊂
36;
%2
6;2'
↪ㅜ㧛஻⠨
4'/#4-5
):: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
)::
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'722'4241&7%6
37#.+6;+56*'5#/'
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌࠊࠅ߹ߖࠎ‫ޕ‬
⇟ภ
01
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-16
257
(75'
㩕㨷㨺㩇㩨
()$18#
2$(
&9)01
14
6;2'01
2'4
8'5
257
(75'
㩕㨷㨺㩇㩨
()$18#
2$(
&9)01
14
6;2'01
#%8
2'4
8'5
5'652'4
8'55'.
4'/#4-5%1&'01
)::
52#4'
):: $1:012
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌ
ࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
(74701'.'%64+%%1.6&
176.+0'
219'4%10641.70+6
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
6;2'
%1&'01
ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌ
ࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
5'652'4
8'55'.
4'/#4-5%1&'01
)::
52#4'
):: $1:012
A-18
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52
6;2'
#%8
(74701'.'%64+%%1.6&
176.+0'
219'4%10641.70+6
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
%1&'01
A-17
数量
Q'TY
用途/備考
REMARKS
1
000-881-447
4
03GL-X-9411
FURUNO ELECTRIC CO .,LTD.
CODE NO.
M4X12 C2700W MBNI2
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
WASHER HEAD SCREW
+-ナベセムスネジB
⇟ภ
01
%75*+10
㩂㩢㨻㩔㩨㩧㩘㩩㩧
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
(2
%1&'01
6/
%1&'01
/:%9/$0+
%1&'01
)
%1&'01
6;2'
%1&'01
ᢙ㊂
36;
).:
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
↪ㅜ㧛஻⠨
4'/#4-5
).: A-20
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇㩒㩆㩨$
)41//'6
㩂㩨㩥㩜㨹㩎
-$(+:+0)/'6#.
-$⋥ઃ㊄ౕ
ฬ‫ޓޓ‬⒓
0#/'
#%%'5514+'5
名 称
NAME
型名/規格
DESCRIPTIONS
1/1
INSTALLATION MATERIALS
番 号
NO.
略 図
OUTLINE
03GL-X-9411 -0
ઃዻຠ⴫
CP03-25604
TYPE
工事材料表
008-539-850
CODE NO.
A-19
⇟ภ
01
%75*+10
㩂㩢㨻㩔㩨㩧㩘㩩㩧
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
6/
%1&'01
/:%9/$0+
%1&'01
)
%1&'01
%1&'01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
).:
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
ᠲ૞ㇱ↪‫ޓޓޓޓ‬
(14%10641.70+6
㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇㩒㩆㩨$
)41//'6
㩂㩨㩥㩜㨹㩎
5'#.
㩖㩨㩡㨼㩧㩎㩨㩆㨺㩣
-$(+:+0)/'6#.
-$⋥ઃ㊄ౕ
6
ฬ‫ޓޓ‬⒓
0#/'
4
3
2
1
番 号
NO.
WING SCREW
蝶ボルト
HEX.NUT
六角ナット 1種
FP03-09870
TYPE
略 図
OUTLINE
100-306-261
000-863-108
000-881-447
000-149-997
4
4
4
4
数量
Q'TY
1/1
03GL-X-9503
用途/備考
REMARKS
Option
03GL-X-9503 -2
A-22
FURUNO ELECTRIC CO .,LTD.
CODE NO.
M5X40 SUS304
CODE NO.
M5 SUS304
CODE NO.
M4X12 C2700W MBNI2
CODE NO.
03-163-7531-1
型名/規格
DESCRIPTIONS
For RCU-014/015/016 Flush mount kit
008-535-630
CODE NO.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
WASHER HEAD SCREW
+-ナベセムスネジB
FLUSH MOUNTING PLATE
フラッシュマウント金具
名 称
NAME
ACCESSORIES
↪ㅜ㧛஻⠨
4'/#4-5
#%%'5514+'5
ᢙ㊂
36;
).: 付属品表
(2
6;2'
ઃዻຠ⴫
%1&'01
A-21
N A M E
ACCESSORIES
03GL-X-9859
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
100-305-370
03-163-2071-0
100-305-190
03-163-1113-0
100-305-140
03-163-1111-0
100-305-180
03-163-1112-0
000-147-143
CP-30-HP-13
000-570-276
KB-13ヨウ ボタンクロ
000-864-131
M10 SUS304
000-864-261
M10 SUS304 000-802-182
M10X30 SUS304
000-802-771
M6X25 SUS304
A-23
Option
1/1
(*2)
1
(*1)
1
1
1
2
4
2
2
2
4
DESCRIPTION/CODE №
Q'TY
FP03-09820/09830
For MU-201CR/231CR Desktop mount kit
O U T L I N E
(略図の寸法は、参考値です。
(*2)䈲䇮FP03-09830↪䈪䈜䇯
*2:䇭FOR FP03-09830.
(*1)䈲䇮FP03-09820↪䈪䈜䇯
*1:䇭FOR FP03-09820.
HANGER STAY
ハンガーササエ(23)
HANGER STAY
ハンガーササエ(20)
HANGER L
ハンガーL(20)
HANGER R
ハンガーR(20)
HOLE PLUG
ホールプラグ
PLASTIC RIVET
スナップボタン
FLAT WASHER
ミガキ平座金
SPRING WASHER
バネ座金
HEX.BOLT
六角ボルト スリワリ
HEX.BOLT
(SLOTTED,WASHER HEAD)
六角セムスB スリワリ
付属品
FP03-09820/09830
PACKING LIST
03GL-X-9859 -0
4
3
2
1
番 号
NO.
WAVE WASHER
波座金
略 図
OUTLINE
840-211-252
000-864-910
000-864-350
000-861-475
数量
Q'TY
4
4
4
2
1/1
03GL-X-9502
用途/備考
REMARKS
Option
03GL-X-9502 -0
FURUNO ELECTRIC CO .,LTD.
CODE NO.
WW-6 SUS
CODE NO.
M6X20 C2700W
ポリシール クロ
CODE NO.
M6 C2700W ポリシール クロ
CODE NO.
14-002-1125-2
型名/規格
DESCRIPTIONS
For MU-201CR/MU-231CR
FP03-09840
TYPE
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
OVAL COUNTERSUNK
HEAD SCREW
+丸皿小ネジ
ROSETTE WASHER
ローゼット座金
HANDLE
取手
名 称
NAME
ACCESSORIES
付属品表
008-535-570
CODE NO.
A-24
0#/'
176.+0'
16*'4+056#..#6+10/#6'4+#.5
+056#..#6+10/#6'4+#.5
70+6
/,#52(%
2'26:$.
%2
%7
&'5%4+26+10%1&'ͳ
)1: 36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
)1:
A-25
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ/,
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
ߘߩઁᎿ᧚
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ
Ꮏ੐᧚ᢱ
/'/14;%#4&+06'4(#%'
㩜㩝㩢㨺㩀㨺㩎㩨㨼㩧㩊㨺㩖㨴㨼㩇
࡙࠾࠶࠻
%7(#4
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
⇟ภ
01
6*4'#&'&41&
ኸಾ㩘㩨㩣㩎
*':076
౐ⷺ㩏㨹㩎‫৻ޓ‬⒳
(.#69#5*'4
㩚㩀㩨㩁ᐔᐳ㊄
524+0)9#5*'4
㩔㩨㩒ᐳ㊄
⇛‫ޓޓ‬࿑
176.+0'
%1&'01
/:575
%1&'01
/575
%1&'01
/575
%1&'01
/575
%1&'01
%㩦㨾㨼
%1&'01
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
)1:
↪ㅜ㧛஻⠨
4'/#4-5
)1: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
.#$'.#66#%*+0)
241%'&74'
⥽ベ㩙㨺㩂⾍ઃⷐ㗔
56''4+0)9*''..#$'.
⥽ベ⾍ࠅ㩙㨺㩂
$5*
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-26
3
2
1
略 図
OUTLINE
CODE NO.
000-881-145
000-802-081
M4X10 C2700W MBNI2
CODE NO.
100-316-250
5X20 SUS304 1シュ
CODE NO.
19-023-3081-0
型名/規格
DESCRIPTIONS
4
4
1
数量
Q'TY
1/1
03GO-X-9502
用途/備考
REMARKS
Option
03GO-X-9502 -0
FURUNO ELECTRIC CO .,LTD.
For CU-200 Desktop mount kit
FP03-10201
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
WASHER HEAD SCREW
+-ナベセムスネジA
+TAPPING SCREW
+トラスタッピンネジ
MOUNTING BRACKET
ハンガー
名 称
NAME
ACCESSORIES
番 号
NO.
付属品表
008-539-530
Q'TY
TYPE
03GL-X-9852 -2
GC-10-2
DESCRIPTION/CODE №
CODE NO.
OUTLINE
A-27
PACKING LIST
NAME
NAME
OUTLINE
1/1
DESCRIPTION/CODE №
Q'TY
M4X8 C2700W MBNI2
+-ナベセムスネジB
予備品
3
SPARE PARTS
SP03-13300
予備品
WASHER HEAD SCREW
000-881-445
M3X8 C2700W MBNI2
1
+-ナベセムスネジB
SPARE PARTS
008-419-280
その他部品
5
WASHER HEAD SCREW
OTHER PARTS
000-881-404
M2.6X10 C2700W MBNI2
+ナベセムスネジA
03-2091(5P)
NHコネクタ
1
2
WASHER HEAD SCREW
NH CONNECTOR ASSY.
008-534-670
03-2090(3P)
VHコネクタ
000-801-844
80-0665
GCカバー組品
1
1
GC COVER ASSY.
VH CONNECTOR ASSY.
008-537-030
008-534-660
03-2089(5P)
VHコネクタ
1
VH CONNECTOR ASSY.
008-534-650
03-2088(6-14P)
XH-PHコネクタ
1
XH-PH CONNECTOR ASSY.
008-534-640
64P1106A
演算プリント
1
PROCESSOR BOARD
004-412-220
231-607/019-FUR
コネクタ(231)
1
CONNECTOR
000-147-414
231-107/026-FUR
コネクタ(231)
1
CONNECTOR
000-147-413
A-28
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
03GL-X-9852
(75'
㩕㨷㨺㩇㩨
()/$#8
()/$8#
2$(
&9)01
14
6;2'01
2'4
8'5
).: ဳᑼ㩄㨺㩎㩨⇟ภ߇㧞Ბߩ႐ว‫ޔ‬ਅᲑࠃࠅ਄Ბߦઍࠊࠆㆊᷰᦼຠߢ޽ࠅ‫ޔ߅ߥޓޕߔ߹޿ߡߞ౉߇߆ࠄߜߤޔ‬ຠ⾰ߪᄌ
ࠊࠅ߹ߖࠎ‫ޕ‬
6916;2'5#0&%1&'5/#;$'.+56'&(14#0+6'/6*'.19'4241&7%6/#;$'5*+22'&+02.#%'1(6*'
722'4241&7%637#.+6;+56*'5#/'
5'652'4
8'55'.
$1:012
4'/#4-5%1&'01
).:
52#4'
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)‫(ޓ‬144'('4'0%'10.;㧕
&9)01
2'4
5'6
914-+0)
37#06+6;
75'
52
6;2'
GC-10
(74701'.'%64+%%1.6&
176.+0'
52#4'2#465.+56(14
0#/'1(
2#46
/(450#/'
+6'/
01
5*+201
%1&'01
A-29
⇟ภ
01
⇛‫ޓޓ‬࿑
176.+0'
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%1&'01
12
%1&'01
/:%9/$0+
%1&'01
/:%9/$0+
%1&'01
Coupling pedestal kit
RCU-014 + MU-201CR
12
ᢙ㊂
36;
).:
4%7/7%4↪
(144%7#0&/7
%4
4%7/7%4↪
(144%7#0&/7
%4
4%7/7%4↪
(144%7#0&/7
%4
4%7/7%4↪
(144%7#0&/7
%4
↪ㅜ㧛஻⠨
4'/#4-5
Option
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
%172.+0)2.#6'#55;
ㅪ⚿บ
⚵ຠ
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇㩒㩆㩨$
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇㩒㩆㩨$
%172.+0)(+:674'
ㅪ⚿㊄ౕ$
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
6;2'
%1&'01
A-30
16*'42#465
176.+0'
/%9/$0+
53
53
&8+&&5.+0-/
2
2
2
2$
5.$(40#
/:%9/$0+
&'5%4+26+10%1&'ͳ
DVI-RGB conversion kit
36;
䋨⇛࿑䈱ኸᴺ䈲䇮ෳ⠨୯䈪䈜䇯㩷㩷㪛㪠㪤㪜㪥㪪㪠㪦㪥㪪㩷㪠㪥㩷㪛㪩㪘㪮㪠㪥㪞㩷㪝㪦㪩㩷㪩㪜㪝㪜㪩㪜㪥㪚㪜㩷㪦㪥㪣㪰㪅䋩
).:
㪫㪮㪦㩷㪫㪰㪧㪜㪪㩷㪘㪥㪛㩷㪚㪦㪛㪜㪪㩷㪤㪘㪰㩷㪙㪜㩷㪣㪠㪪㪫㪜㪛㩷㪝㪦㪩㩷㪘㪥㩷㪠㪫㪜㪤㪅㩷㩷㪫㪟㪜㩷㪣㪦㪮㪜㪩㩷㪧㪩㪦㪛㪬㪚㪫㩷㪤㪘㪰㩷㪙㪜㩷㪪㪟㪠㪧㪧㪜㪛㩷㪠㪥㩷㪧㪣㪘㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪧㪧㪜㪩㩷
㪧㪩㪦㪛㪬㪚㪫㪅㩷㪨㪬㪘㪣㪠㪫㪰㩷㪠㪪㩷㪫㪟㪜㩷㪪㪘㪤㪜㪅
A-31
Option
).: ဳᑼ㪆䍘䍎䍢䍼⇟ภ䈏䋲Ბ䈱႐ว䇮ਅᲑ䉋䉍਄Ბ䈮ઍ䉒䉎ㆊᷰᦼຠ䈪䈅䉍䇮䈬䈤䉌䈎䈏౉䈦䈩䈇䉁䈜䇯䇭䈭䈍䇮ຠ⾰䈲ᄌ䉒䉍䉁䈞䉖䇯
524+0)9#5*'4
㩔㩨㩒㩅㩨㩀㩨㩒
52#%'4
㩇㩗㩩㨺㩅㨺
%#$.'#55;
㩃㨺㩖㩨㩣⚵ຠ
:*%100'%614#55;
:*㩄㩒㩂㩊⚵ຠ
:*%100'%614#55;
:*㩄㩒㩂㩊⚵ຠ
8*%100'%614#55;
8*㩄㩒㩂㩊⚵ຠ
4)$$7(($1#4&
4)$$7((㩖㩩㩢㩧㩎
&8+4)$#55;
&8+4)$⚵ຠ
9#5*'4*'#&5%4'9
㩏㩗㩨㩈㩛㩇㩒㩆㩨$
0#/'
ߘߩઁㇱຠ
12
㧼㧭㧯㧷㧵㧺㧳‫ޓ‬㧸㧵㧿㨀
⇟ภ
01
⇛‫ޓޓ‬࿑
176.+0'
For LAN cable kit
%1&'01
/25%
ဳฬ㧛ⷙᩰ
&'5%4+26+105
%2
6;2'
ᢙ㊂
36;
).:
↪ㅜ㧛஻⠨
4'/#4-5
Option
).: 㧲㨁㧾㨁㧺㧻‫ޓ‬㧱㧸㧱㧯㨀㧾㧵㧯‫ޓ‬㧯㧻‫ޓ‬㧚㧘㧸㨀㧰
㧔⇛࿑ߩኸᴺߪ‫ޔ‬ෳ⠨୯ߢߔ‫&ޓޕ‬+/'05+105+0&4#9+0)(144'('4'0%'10.;㧕
/1&7.#4%100%614
㩄㩒㩂㩊
㩝㩆㩨㨷㩡㨺
ฬ‫ޓޓ‬⒓
0#/'
+056#..#6+10/#6'4+#.5
Ꮏ੐᧚ᢱ⴫
%1&'01
A-32
D-1
D-2
D-3
Takahashi T.
Y. Hatai
Y. Hatai
Takahashi T.
D-4
Y. Hatai
Takahashi T.
D-5
Y. Hatai
Takahashi T.
D-6
Y. Hatai
D-7
Y. Hatai
Takahashi T.
D-8
Y. Hatai
Takahashi T.
D-9
Y. Hatai
D-10
Y. Hatai
Takahashi T.
D-11
Y. Hatai
Takahashi T.
D-12
Y. Hatai
Takahashi T.
D-13
Y. Hatai
D-14
Y. Hatai
D-15
Y. Hatai
D-16
Y. Hatai
D-17
Y. Hatai
D-18
Apr.05'04
D-19
注記
*1)造船所手配。
*2)オプション。
*3)最長 100m (延長するときは接続箱RJB-001が必要 )。
*4)保護アース用ケーブルは緑/黄の絶縁線を使用のこと。
*5)FAR-2167DS-BBのときは支給なし。
保護アース
PE *1 *4
IV-8sq.
トランス
TRANSFORMER
RU-1803 *2
DPYC-2.5
*1
1
2
3
NOTES
*1: SHIPYARD SUPPLY.
*2: OPTION.
*3: MAX. 100m. (JUNCTION BOX RJB-001 IS REQUIRED FOR EXTENSION)
*4: USE GRN/YEL WIRE FOR PROTECTIVE EARTH.
*5: NOT SUPPLIED FOR FAR-2167DS-BB.
表示部
MONITOR UNIT *5
MU-201CR
保護アース
PE
*1 *4
IV-8sq.
DRAWN
Oct. 6 '06
CHECKED
APPROVED
SCALE
DWG.No.
1
2
3
4
5
6
7
8
Maki
TAKAHASHI.T
MASS
kg
C3523-C01- B
1
2
3
4
5
6
7
8
1
2
3
TXP
TXN
RXP
NC
NC
RXN
NC
NC
防水型カードインターフェイス
MEMORY CARD I/F UNIT
CU-200
*2
AC
AC
GND
P
P
NR203PF-VVS1.25
3.5m, φ8.6
MPS588-C
100-230VAC
1φ,50/60Hz
*1
LAN CABLE(CAT5) OR
FR-FTPC-CY,10/20/30m,φ13
シロ/ミドリ WHT/GRN
ミドリ
GRN
シロ/ダイ WHT/ORG
アオ
BLU
シロ/アオ WHT/BLU
ダイ
ORG
シロ/チャ WHT/BRN
チャ
BRN
P5E-4PTX-BL,10m,φ6.3
1
2
3
4
5
6
7
8
TXP
TXN
RXP
NC
NC
RXN
NC
NC
NETWORK
SAME AS AVOBE
DVI-D MONITOR
J205
J615
+12V
GND
+5V
GND
-12V
1
2
1
2
3
4
5
6
7
8
9
J622
SYS_ACK-H
SYS_ACK-C
J601
NC
RXD
TXD
NC
GND
NC
NC
NC
NC
P
P
J607
LOG-A 1
LOG-B 2
NC 3
J619
ARPA-A 1
ARPA-B 2
NC 3
J611
AIS_TD-A 1
AIS_TD-B 2
AIS_RD-A 3
AIS_RD-B 4
AIS_GND 5
*1
IV-1.25sq.
TYPE
名 称
Y.Hatai
NAME
RW-4864,φ9.5
RW-4864,φ9.5
RW-4864,φ9.5
*1
TTYCS-7
*1
TTYCS-4
*1
TTYCS-4
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1
*1
TTYCS-1Q
RS-232C CABLE
J502/J522
KEY_TXD-B
KEY_TXD-A
KEY_RXD-B
KEY_RXD-A
PWR_SW
GND
+12V
GND
NC
NC
PC
1
2
3
4
5
6
7
8
9
10
SUB DISPLAY2
(SEMI-LOG)
SUB DISPLAY1
(FULL-LOG)
MASTER RADAR
ALARM SYSTEM
AIS
(IEC-61162-2)
TRACK_CONTROL
(IEC-61162-1)
ECDIS
(IEC-61162-1)
SPEED LOG
(IEC-61162-1)
NAVIGATOR
(IEC-61162-1)
HDG SENSOR
(IEC-61162-2)
*1
J501/J521
1 KEY_TXD-B
2 KEY_TXD-A
3 KEY_RXD-B
4 KEY_RXD-A
5 PWR_SW
6 GND
7 +12V
8 GND
9 SYS_FAIL-H
10 SYS_FAIL-C
J507/J527
1 SYS_FAIL-H
2 SYS_FAIL-C
3 SYS_ACK-H
4 SYS_ACK-C
TOTAL: UP TO 31.5m
1
2
3
4
5
6
7
8
9
10
J501
KEY_TXD-B
KEY_TXD-A
KEY_RXD-B
KEY_RXD-A
PWR_SW
GND
+12V
GND
NC
NC
XH10P-W-5P-A
1.5/10/20/30m,φ9
SPU_RF_D-A
SPU_RF_D-B
RF_SPU_D-A
RF_SPU_D-B
SG
GND
TB802
IF_VIDEO
GND
5
J618(NH)
GND 1
OP_HD_2 2
GND 3
OP_BP_2 4
GND 5
OP_TRIG_2 6
GND 7
OP_VIDEO_2 8
J617(NH)
GND 1
OP_HD_1 2
GND 3
OP_BP_1 4
GND 5
OP_TRIG_1 6
GND 7
OP_VIDEO_1 8
J616(NH)
GND 1
OP_HD_IN 2
GND 3
OP_BP_IN 4
GND 5
OP_TRIG_IN 6
GND 7
OP_VIDEO_IN 8
P
P
P
P
P
P
P
P
P
P
P
J606
NAV-A 1
NAV-B 2
NC 3
J620
TRK_TD-A 1
TRK_TD-B 2
TRK_RD-A 3
TRK_RD-B 4
GND 5
P
J605
HDG-A 1
HDG-B 2
HDG_GND 3
J612
ALARM1_0 1
ALARM1_1 2
ALARM2_0 3
ALARM2_1 4
ALARM3_0 5
ALARM3_1 6
OPERATOR_FITNESS_0 7
OPERATOR_FITNESS_1 8
EXT_ALM_ACK_N 9
GND 10
SYS_FAIL-H 11
SYS_FAIL-C 12
J614
1 +12V
2 GND
1
2
3
4
5
J602
KEY_TXD-B 1
KEY_TXD-A 2
KEY_RXD-B 3
KEY_RXD-A 4
PWR_SW 5
GND 6
+12V 7
GND 8
SYS_FAIL-H 9
SYS_FAIL-C 10
XH10P-W-6P
2.3/10/20/30m,φ9
合計:31.5m以下
RED
GRN
BLK
WHT
GRN[B]
RED[B]
4
P
P
MPS588-C
MJ-A3SPF0015,10m,φ6
DVI-D/DSINGLELINK5M/10M
5/10m,φ7
J302
TXP
TXN
RXP
NC
NC
RXN
NC
NC
MJ-A3SPF
J1
シロ WHT
+12V 1
クロ BLK
GND 2
FG 3
RGBビデオコンバータ
RGB VIDEO CONVERTOR
DVI-RGB-1 *2
24
BRN
RED
ORG
YEL
GRN
制御部
PROCESSOR UNIT
RPU-013
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
DVI-D MONITOR
J204
DVI0TX2_N
DVI0TX2_P
A_GND
NC
NC
NC
NC
NC
DVI0TX1_N
DVI0TX1_P
A_GND
NC
NC
VCC
GND
NC
DVI0TXD_N
DVI0TXD_P
A_GND
NC
NC
A_GND
DVI0TXC_P
DVI0TXC_N
チャ
アカ
ダイ
キ
ミドリ
23
24
1
2
RS-232C
*2
DVI CABLE
J3
アカ
ミドリ
クロ
シロ
ミドリ(太)
アカ(太)
24V_PLUS
24V_MINUS
TB801
TX_HV
3
外部モニター
EXT. MONITOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
J9
R
GND
G
GND
B
GND
HS
GND
VS
GND
1
2
3
4
操作部
CONTROL UNIT
RCU-014/015
TMDS_DATA2(-)
TMDS_DATA2(+)
TMDS_DATA2/4_SHIELD
NC
NC
DDC_CLOCK
DDC_DATA
NC
TMDS_DATA(-)
TMDS_DATA(+)
TMDS_DATA1/3_SHIELD
NC
NC
+5V_POWER
GND
HOT_PLUG_DETECT
TMDS_DATAB(-)
TMDS_DATAB(+)
TMDS_DATA0/5_SHIELD
NC
NC
TMDS_CLOCK_SHIELD
TMDS_CLOCK(+)
TMDS_CLOCK(-)
J3
5
6
7
8
9
10
3
4
1
2
P
P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
操作部
CONTROL UNIT
RCU-016 *2
TB1
1 H
2 C
TB1
1 H
2 C
1
2
3
4
5
6
7
8
9
10
11
12
13
03-2091(5P)
チャ BRN
アカ RED
ダイ ORG
キ
YEL
*3
RW-9600,15/30/40/50m,φ22
チャ
BRN
ダイ(太) ORG[B]
キ(太)
YEL[B]
*1
TPYCY-1.5,MAX.100m
TB901
1 U
2 V
3 W
TB803
9 GND
10
11 TX_SIG
2
100-240VAC
1φ,50-60Hz
BNCコネクタコンバータ
BNC CONNECTOR
CONVERTER
DSUB-BNC-1 *2
J3
VCC
GND
-5/-12V
DPYC-2.5 *1
J1
1
2
3
4
5
J603(XH)
GC_LED
GC_HOLD
GC_UP
J610
GC_DOWN
24V_PLUS 1
GC_0V
24V_MINUS 2
GC_5V
MOTOR(+) 3
J608
MOTOR(+) 4
AD_DATA-H MOTOR(-) 5
AD_DATA-C MOTOR(-) 6
AD_CLK-H SPU_RF_D-A 7
AD_CLK-C SPU_RF_D-B 8
RF_SPU_D-A 9
RF_SPU_D-B 10
SG 11
GND 12
J609
IF_VIDEO
GND
TB BOARD
03P9342
100-120/
200-240VAC
1φ,50-60Hz
R_VIDEO
GND
G_VIDEO
GND
B_VIDEO
GND
H_SYNC
GND
V_SYNC
GND
VCC
GND
-5/-12V
RGB バッファ 基板
RGB BUFFER PCB
03P9229A
J4
+12V
+12V
GND
GND
NC
NC
DPYC-1.5 *1
J2
R_VIDEO
G_VIDEO
B_VIDEO
NC
NC
GND
GND
GND
NC
GND
GND
NC
H_SYNC
Y_SYNC
NC
J7(NH)
DATA1-H
DATA1-C
SHIFT1-H
SHIFT1-C
FG
DVI-RGB変換基板
DVI-RGB CONVERSION BOARD
SLB-FRN4-A
440VAC
1φ,50-60Hz
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
BRN
3
RED
1
ORG
2
YEL
3
GRN
4
BLU
5
PPL
03-2089(5P)
03-2088(6-14P) 1
2
3
4
5
6
J604
1 +12V
2 ANT_ON_N
J621
6 GND
VDR
*1
J680
チャ
アカ
ダイ
キ
ミドリ
アオ
ムラサキ
9
10
11
12
13
14
*1
TPYC-1.5,MAX.100m
アカ RED
シロ WHT
クロ BLK
TX_HV 6
TX_SIG 8
GND 9
*1
TPYCY-2.5,MAX.100m
RW-4747
*1
COAX.(75Ω)x5
VGA CABLE
*1
1
2
3
4
5
6
7
J1
RU-5466-1 *2
GYRO CONVERTER
BOARD
64P1106A *2
RGB EXT. MONITOR
TTYCS-4
保護アース
*1 *4
PE
IV-8sq.
*1
440VAC,3φ,50Hz
RU-6522 *2
保護アース
PE
*1 *4
IV-8sq.
MPYC-7
TPYC-2.5 *1
220VAC,3φ,50Hz
GND 13
RED
WHT
BLK
J5(VH)
GYRO_R2
GYRO_R1
NC
J4(VH)
GYRO_S1
GYRO_S2
GYRO_S3
GYRO_T
GYRO_FG
TPYC-2.5 *1
RU-5693 *2
アカ RED
シロ WHT
クロ BLK
TB3
U 1
V 2
W 3
電源制御部
POWER SUPPLY TB3
UNIT
+12V 11
PSU-006 ANT_ON 12
03-2090(3P)
TPYC-2.5 *1
110VAC,3φ,60Hz
TB1
1
2
TB2
1 U
2 V
3 W
B
TPYC-2.5 *1
RU-1803 *2
A
200/380VAC,3φ,50Hz
220/440VAC,3φ,60Hz
DPYC-2.5 *1
100-115/220-230VAC,1φ,50/60Hz
空中線部
ANTENNA UNIT
RSB-111/112
A-D CONVERTER
GYROCOMPASS
D
DPYC-2.5 *1
C
440VAC,1φ,50-60Hz
1
6
S-1
空中線型式 回転数 電源
ANT. TYPE
RPM
POWER SUPPLY
RSB-111
21
200VAC,3φ,50Hz
26
220VAC,3φ,60Hz
RSB-112
21
380VAC,3φ,50Hz
26
440VAC,3φ,60Hz
LAN
スイッチング ハブ
*2
SWITCHING HUB
HUB-100 (8 PORTS)
保護アース PE
IV-1.25sq. *1 *4
FAR-2167DS/2167DS-BB
船舶用レーダー/ARPA
相互結線図
MARINE RADAR/ARPA
INTERCONNECTION DIAGRAM
Download PDF

advertising