Furuno FCV-1200LM Radar Detector User Manual

COLOR LCD SOUNDER
FCV-1200L/1200LM
Your Local Agent/Dealer
9-52 Ashihara-cho,
Nishinomiya, Japan
Telephone :
0798-65-2111
Telefax :
0798-65-4200
All rights reserved.
Printed in Japan
FIRST EDITION : APR. 2000
L
PUB.No. OME-23650
( DAMI ) FCV-1200L/LM
: JUN. 10,2002
*00080900500*
*00080900500*
*00080900500*
*OME23650L00*
*OME23650L00*
*OME23650L00*
SAFETY INSTRUCTIONS
WARNING
ELECTRICAL SHOCK HAZARD
WARNING
Keep heater away from equipment.
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
A heater can melt the equipment's power
cord, which can cause fire or electrical
shock.
Use the proper fuse.
Immediately turn off the power at the
switchboard if water leaks into the
equipment or something is dropped in
the equipment.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in equipment
damage.
CAUTION
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or illegible, contact
a FURUNO agent or dealer.
(Processor unit)
Name: Warning Label (1)
To avoid electrical shock, do not Type: 86-003-1011-0
remove cover. No user-serviceable
Code No.: 100-236-230
parts inside.
WARNING
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Make sure no rain or water splash leaks
into the equipment.
(Monitor unit)
Name: Warning Label (2)
Type: 03-129-1001-0
Code No.: 100-236-740
DANGER
Electrical shock hazard.
Power off control unit
and unplug CN2 before
servicing.
(Processor unit)
Name: Power Warning
Label
Type: 02-127-2002-0
Code No.: 100-283-240
Fire or electrical shock can result if water
leaks in the equipment.
About the TFT LCD
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01%
of the pixels may drop out or blink, however this is not an indication of malfunction.
i
FOREWORD
A Word to FCV-1200L/1200LM Owners
Congratulations on your choice of the FURUNO FCV-1200L/FCV-1200LM COLOR LCD
SOUNDER. We are confident you will see why the FURUNO name has become synonymous
with quality and reliability.
FCV-1200L is a dual-frequency color LCD sounder, and FCV-1200LM is a monitor which
displays the signal from an external video sounder.
For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative
and dependable marine electronics equipment. This dedication to excellence is furthered by our
extensive global network of agents and dealers.
This equipment is designed and constructed to meet the rigorous demands of the marine
environment. However, no machine can perform its intended function unless installed, operated
and maintained properly. Please carefully read and follow the recommended procedures for
operation and maintenance.
We would appreciate hearing from you, the end-user, about whether we are achieving our
purposes.
Thank you for considering and purchasing FURUNO equipment.
Features
•
8- or 16- color presentation (including background) provides detailed information on fish
density and bottom composition, on a 10.4 inch color LCD.
•
Furuno Free Synthesizer (FFS) transceiver design allows use of user-selectable operating
frequencies.
•
•
•
•
•
You can select display orientation; Portrait (vertical) or Landscape (horizontal).
•
ii
Automatic bottom tracking features permits unattended operation.
Frequency mixing picture helps discriminate fish species.
Alarms: Fish, Bottom, Fish-Bottom, Water Temperature (temperature data required).
A-scope presentation displays echoes at each transmission with amplitudes and colors
according to intensities.
Unique split range control allows independent range settings in dual-frequency mode.
TABLE OF CONTENTS
FOREWORD...................................................................................................................ii
INDICATIONS .................................................................................................................v
SYSTEM CONFIGURATION .........................................................................................vi
1.
BASIC OPERATION ............................................................................................ 1-1
1.1 Key/Control Operation ...............................................................................................................1-1
1.2 Turning the Power On/Off..........................................................................................................1-3
1.3 Adjusting the Brilliance of LCD and Key Panel .........................................................................1-3
1.4 Presentation Mode ....................................................................................................................1-4
1.5 Selecting Basic Range ............................................................................................................ 1-11
1.6 Shifting the Basic Range .........................................................................................................1-12
1.7 Adjusting Gain .........................................................................................................................1-13
1.8 Measuring Depth .....................................................................................................................1-13
1.9 Marker Line..............................................................................................................................1-14
1.10 Adjusting Clutter ......................................................................................................................1-15
1.11 Adjusting TVG .........................................................................................................................1-16
1.12 Eliminating Weak Echoes........................................................................................................1-18
1.13 Picture Advance Speed ...........................................................................................................1-19
1.14 A-Scope Display ......................................................................................................................1-21
1.15 Suppressing Interference ........................................................................................................1-22
1.16 Adjusting the External Video Sounder Picture ........................................................................1-24
2.
MENU OPERATION............................................................................................. 2-1
2.1 Basic Menu Operation ...............................................................................................................2-1
2.2 DISP Menu ................................................................................................................................2-3
2.3 ALM Menu .................................................................................................................................2-6
2.4 TX/RX Menu ..............................................................................................................................2-9
2.5 USER-1/2 Menu ...................................................................................................................... 2-11
iii
3.
SYSTEM MENU................................................................................................... 3-1
3.1 SYSTEM Menu Operation .........................................................................................................3-1
3.2 SYSTEM SETTING Menu .........................................................................................................3-2
3.3 ES/DRAFT SETTING Menu ......................................................................................................3-4
3.4 RANGE SETTING Menu ...........................................................................................................3-7
3.5 TEMP SETTING Menu ..............................................................................................................3-9
3.6 NET SONDE SETTING Menu .................................................................................................3-10
3.7 USER COLOR SETTING Menu ..............................................................................................3-13
3.8 USER CLUTTER SETTING Menu ..........................................................................................3-15
3.9 NAV DATA SETTING Menu.....................................................................................................3-16
3.10 TARGET ECHO SETTING Menu ............................................................................................3-17
4.
INTERPRETING THE DISPLAY .......................................................................... 4-1
4.1 Color Bar....................................................................................................................................4-1
4.2 Zero Line....................................................................................................................................4-2
4.3 Bottom Echoes ..........................................................................................................................4-2
4.4 Fish Schools ..............................................................................................................................4-3
4.5 Other Echoes.............................................................................................................................4-4
5.
MAINTENANCE & TROUBLESHOOTING.......................................................... 5-1
5.1 Maintenance ..............................................................................................................................5-1
5.2 Fuse Replacement ....................................................................................................................5-2
5.3 Troubleshooting ......................................................................................................................... 5.3
5.4 Diagnostic Test ..........................................................................................................................5-4
5.5 Test Pattern ...............................................................................................................................5-6
5.6 Default Setting ...........................................................................................................................5-7
APPENDIX 1
MENU TREE...................................................................................AP-1
APPENDIX 2
SCREEN DIVISION ........................................................................AP-6
APPENDIX 3
DISPLAY DIVISION........................................................................AP-9
INDEX ........................................................................................................................ IN-1
iv
INDICATIONS
The illustration below shows the indications as they appear on the portrait-type monitor unit.
Their locations are also the same on the landscape-type monitor unit. This manual shows all
display screen illustrations using the portrait-type monitor unit.
Picture advance speed
Frequency
Noise limiter
Shift
Water temperature
Minute marker
Elapsed time
1/1
5.3 F
LF N1
0
0
x H xx M
Marker
line
10
F
Alarm marker
19.7
20
Color bar
Alarm
Zero line
VRM Depth
VRM marker
5
40
Temperature scale*
0
Water temperature graph*
Depth scale
Fish school
Seabed
60
Ship's speed*
Depth
17.8kt
49.6
1'21" <P/R>
*: Appropriate sensors required
ft
Scroll time
80
Transducer power reduction (FCV-1200L only)
v
SYSTEM CONFIGURATION
Note: This equipment is intended for marine use only.
Standard type
Monitor unit MU-101C is supplied as standard. The illustration below shows the portrait-type
monitor unit and control unit.
MONITOR UNIT MU-101C
CONTROL UNIT
CV-1201: Portrait type
CV-1202: Landscape type
Navigator *4
NMEA 0183
External Monitor
Interface Unit
IF-8000
PROCESSOR UNIT
CV-1203 (FCV-1200L)
CV-1203M (FCV-1200LM)
Water Temp. Sensor
(T-02MSB, etc.)
Net Sonde
FNZ-18
Ship's Mains
12-24 VDC
E/S Interface
VI-1100A
HI
Rectifier
RU-1746B-2
Sonar, Net Recorder,
Telesounder TS-50/80 *3
E/S Interface
VI-1100A
LO
100/110/115/200/
220/230 VAC
1φ, 50/60 Hz
Navigator *4
Same as above
OR
Transceiver Unit ETR-5D/10D
Telesounder TS-7000/8000 *3
Same as above
High
Frequency
Transducer*1
: Standard
Low
Frequency
OR
Transducer*1
: Option
: Local Supply
*1: FCV-1200L only
*2: EXIF Assy. required for FCV-1200L.
*3: For sister ship one unit only
Sister ship: EXIF Assy. required for FCV-1200L
Master ship: FCV-1200LM or FCV-1200L equipped with EXIF Assy.
*4: Navigator may be connected to interface unit or monitor unit.
vi
Switch Box
EX-7
Picture Recorder
MT-12
E/S Interface VI-1100A
OR
Transmitter Unit ETR-5D/10D
Same as above
Same as above
Same as above
*2
Blackbox type
Monitor unit MU-101C is not supplied. The external monitor is required. Connect the control unit
CV-1201 or CV-1202 to the interface unit IF-8000.
MONITOR UNIT
MU-101C
External Monitor
Navigator
NMEA 0183
Interface Unit
IF-8000
CONTROL UNIT
CV-1201: Portrait type
CV-1202: Landscape type
*4
Interface Unit
IF-8000
PROCESSOR UNIT
CV-1203 (FCV-1200L)
CV-1203M (FCV-1200LM)
Water Temp. Sensor
(T-02MSB, etc.)
External Monitor
Net Sonde
FNZ-18
Ship's Mains
12-24 VDC
E/S Interface
VI-1100A
HI
Rectifier
RU-1746B-2
E/S Interface
VI-1100A
LO
100/110/115/200/
220/230 VAC
1φ, 50/60 Hz
Sonar, Net Recorder,
Telesounder TS-50/80 *3
Same as above
OR
Transceiver Unit ETR-5D/10D
Telesounder TS-7000/8000 *3
Same as above
High
Frequency
Transducer*1
: Standard
Low
Frequency
OR
Transducer*1
: Option
: Local Supply
*1: FCV-1200L only
*2: EXIF Assy. required for FCV-1200L.
*3: For sister ship one unit only
Sister ship: EXIF Assy. required for FCV-1200L
Master ship: FCV-1200LM or FCV-1200L equipped with EXIF Assy.
*4: When connecting optional monitor unit, connect it to control unit.
Switch Box
EX-7
Picture Recorder
MT-12
E/S Interface VI-1100A
OR
Transceiver Unit ETR-5D/10D
Same as above
Same as above
Same as above
*2
vii
This page is intentionally left blank.
1. BASIC OPERATION
1.1
Key/Control Operation
1.1.1
Portrait-type control unit
Monitor Unit
Correct key operation: One beep
Wrong key operation: Two beeps
Control
Unit
COLOR LCD SOUNDER FCV– 1200L
Adjusts dimmer of the display
and control panel. (P. 1-3)
MARKER
TLL
BRILL
PWR
Inscribes marks on the display
(P. 1-14).
SHIFT
Turns power on/off.
(P. 1-3)
• Shifts the display area.
(P. 1-12)
• Changes the menu setting.
(P. 2-1)
VRM
ADVANCE/A-SCOPE
SIG LEVEL
NL
TVG
GAIN-EXT
• Shifts VRM/WHITE
MARKER. (P. 1-13)
• Selects menu item.
(P. 2-1)
CLUTTER
MENU
EXIT
FUNCTION
Selects a display range. (P. 1-11)
RANGE
DUAL
HF
ZOOM
LF
ZOOM
Selects a display.
(P. 1-4)
USER-1
USER-2
MODE
LF
4
HF
6
2
8
0
4
6
0
10
2
10
8
GAIN
Adjusts gain of high and low
frequencies individually. (P. 1-13)
Opens the SIGNAL
LEVEL menu.
(P. 1-18)
Opens the TVG
menu. (P. 1-16)
Opens the CLUTTER
menu. (P. 1-15)
Opens the PIC ADVANCE/A-SCOPE menu.
(P. 1-19, 1-21)
Opens the NOISE
LIMITER menu. (P. 1-22)
ADVANCE/A-SCOPE
SIG LEVEL
TVG
NL
GAIN-EXT
CLUTTER
MENU
Opens the EXTERNAL
ECHO menu. (P. 1-24)
EXIT
Opens the main menu. (P. 2-1)
Closes menus.
FUNCTION
Control unit (Portrait type)
1-1
1.1.2
Landscape-type control unit
Monitor Unit
Control Unit
Adjusts dimmer of the
display and control
panel (P. 1-13).
Correct key operation: One beep
Wrong key operations:Two beeps
· Shifts the display area. (P. 1-12)
· Changes menu setting. (P. 2-1)
Inscribes marks
on the display
(P. 1-14).
MARKER
TLL
Selects the display.
(P.1-4)
SHIFT
HF
VRM
LF
ZOOM
HF
ZOOM
8
0
10
4
6
USER1
MENU
CLUTTER
6
2
DUAL
ADVANCE/A-SCOPE
SIG LEVEL
NL
GAIN-EXT
TVG
BRILL
4
COLOR LCD SOUNDER FCV– 1200L
GAIN
LF
USER2
EXIT
2
PWR
RANGE
FUNCTION
8
MODE
0
Turns power on/off.
(P.1-3)
Selects the
display range. (P. 1-11)
10
Adjusts gain of high and
low frequencies individually.
(P. 1-13)
· Shifts VRM/WHITE
MARKER. (P. 1-13)
· Selects menu item.
(P. 2-1)
Opens the SIGNAL
LEVEL menu.
(P. 1-18)
Opens the TVG
menu. (P. 1-16)
Opens the CLUTTER
menu. (P. 1-15)
Opens the PIC ADVANCE/A-SCOPE
menu.(P. 1-19, 1-21)
Opens the NOISE
LIMITER menu.
ADVANCE/A-SCOPE
(P. 1-22)
SIG LEVEL
TVG
NL
GAIN-EXT
MENU
CLUTTER
EXIT
FUNCTION
Control unit (Landscape type)
1-2
Opens the
EXTERNAL
ECHO menu. (P. 1-24)
Opens the main
menu. (P. 2-1)
1.2
1.
Turning the Power On/Off
Press the [PWR] key to turn the power on.
Beep sounds, and then the power turns on. The display selected with the [MODE] switch
appears.
2.
Press the [PWR] key again to turn the power off.
Note: Wait for five seconds before turning on the power again.
1.3
Adjusting the Brilliance of LCD and Key Panel
The brilliance of the LCD and the dimmer of key panel may be adjusted as below. The LCD
brilliance is adjustable 10 steps; the panel dimmer in 5 steps.
1.
Press the [BRILL] key to open the BRILL/PANEL DIMMER window.
BRILL/PANEL DIMMER
(9) [
]
[
]
PANEL DIM (4) [
]
[
]
BRILL
Note: Location of arrow keys on the brilliance setting
window is opposite of same controls on the control unit.
Brill/panel dimmer window
2.
Press the [+] or [-] key to adjust the LCD brilliance (0 – 9).
([+] key: bright, [-] key: dark)
Note:Brilliance must be adjusted within five seconds after pressing the [BRILL] key or the
brill/panel dimmer window will be erased.
3.
Press the [!] or ["] key to adjust the key panel dimmer (0 – 4, 0: OFF, 4: Maximum).
Adjust the key panel brilliance within five seconds or the window will be erased.
Note1: When turning off the power with brilliance set to minimum, since nothing will appear on
the display the next time the power is turned on. In this case, press the [BRILL] key several
times.
Note2: The brilliance of a commercial monitor cannot be adjusted with the [BRILL] key. Use the
associated control on the monitor.
1-3
1.4
Presentation Mode
Seven presentation modes are available with the [MODE] switch.
M O D E
LF-ZOOM
LF
DUAL
HF
HF-ZOOM
USER-1
USER-2
Currentry selected mode
shown in reverce video
Display mode window
Single picture (low frequency or high frequency)
Low frequency (LF)
The lower the frequency of the ultrasonic pulse the wider the detection area. Thus, the low
frequency is suitable for general search and judging bottom condition.
High frequency (HF)
The higher the frequency of the ultrasonic pulse the better the resolution. Therefore, the high
frequency pulse is useful for detailed observation of fish echoes.
1/1
LF
0.0
0
0
20
Fish school
Low
frequency
High
frequency
40
Bottom
60
49.6
ft
80
Detection Area
Single Picture
Comparison of detection ranges, sample single picture (low frequency)
1-4
Dual
Provides the low frequency picture on the left 1/2 of the screen; the high frequency on the right
1/2.
1/1
LF
0
HF
0.0
0
0
Low
frequency
High
frequency
20
20
40
40
60
60
49.6 ft 80
80
Frequency
Low
High
Beamwidth
wide
Narrow
Echo trail
Long
Short
Dual frequency display
1-5
ZOOM
The “single picture” (high or low frequency) appears on the right 1/2 of the screen and the zoom
picture on the left 1/2. The zoom picture may be selected among BOTTOM LOCK, BOTTOM
ZOOM, MARKER ZOOM, DISCRIM (discrimination) 1/2 and DISCRIM (discrimination) 1/3. The
default zoom picture is BOTTOM LOCK. You can select through the menu. See page 2-3.
BOTTOM LOCK
The bottom lock display shows the area between the zoom marker and the bottom as a straight
line to distinguish it from fish near the bottom, and thus it is useful for discriminating fish near
the bottom.
1/1
5
Bottom lock display
LF
0
00
Zoom marker
4
Zoomed fish school
10
3
20
This area zoomed
and displayed on left
1/2 of screen.
2
1
Bottom as a straight line
21.7 ft
0
Fish
school
30
Single frequency display
40
Bottom lock display
1-6
BOTTOM ZOOM
The bottom zoom display shows the zoomed bottom (automatically tracked) on the left 1/2 of
the screen. When the bottom depth increases, the display shifts to keep the bottom echo at the
lower part of the screen.
1/1
LF
Bottom zoom
display
0
00
24
26
10
Single frequency display
28
Zoom marker (current)
20
Bottom
30
30
32
Zoom marker (past)
29.8 ft 34
40
Bottom zoom display
MARKER ZOOM
The marker zoom display expands the area selected with the VRM on the normal picture to full
vertical size of the screen on the left-half window. This mode is useful for observing specific fish
school.
1/1
Marker zoom
display
LF
0
00
12
14
11.5
Fish school
Zoomed fish school
16
VRM (Green)
10
This area is zoomed.
20
18
30
Single frequency display
20
25.0 ft
40
Zoom marker
Marker zoom display
1-7
DISCRIM 1/2
The discrim(ination) 1/2 screen shows the single picture on the right 1/2 of the screen and the
bottom lock display and discriminator display occupy the left 1/2 of the screen. The discriminator
display shows the bottom as a straight line, which is useful for determining bottom hardness.
1/1
Bottom lock display
LF
0
00
2
10
1
Bottom trail
Long tail=Hard bottom
Short tail=Soft bottom
0
20
10
30
Single frequency display
Bottom discrimination
display
21.5 ft 20
40
Discrim 1/2 display
DISCRIM 1/3
This display is similar to the DISCRIM 1/2 display except the bottom discriminator display
occupies only 1/3 of the left 1/2 of the screen as below.
1/1
LF
0
00
Bottom zoom
display
3
2
10
Bottom trail
1
Long tail=Hard bottom
Short tail=Soft bottom
20
0
30
Single frequency display
Bottom discrimination
display
21.5 ft 10
Discrim 1/3 display
1-8
40
USER 1, 2
The display set at the user 1 (user 2) menu appears. Default setting is as follows.
USER 1: Vertical split three screens (LF + HF + MIX)
USER 2: Vertical and horizontal split four screens (LF + HF + LF bottom lock +HF bottom lock
displays)
This setting may be changed through the menu. For further details see page 2-11.
LF
0
1/1
HF
MIX
0
0
0
10
10
10
20
20
20
30
30
30
40
40
40
ft
24.8
High
Low
Mix
frequency frequency display*
User 1 display
*Mix
This mode compares echo intensity between low and high frequencies, and displays echoes
from tiny fish in discriminative colors. This is done by utilizing the fact that tiny fish return a
stronger echo against a high frequency rather than a low frequency. This is done as below.
1.
If a high frequency echo is stronger than the corresponding echo on the low frequency, the
high frequency echo is displayed.
2.
If the low frequency echo is stronger than or equal to the high frequency echo, it is less
likely to be a tiny fish and therefore is displayed in blue.
3.
If the echoes on both frequencies have the intensity corresponding to reddish brown or red,
they are displayed in reddish brown or red: this is necessary to display the zero line and
bottom in reddish brown or red.
In other words, the echoes displayed in orange thru light-blue may be considered to be tiny fish
such as whitebait.
1-9
High frequency
Low frequency
Blue
Green
YEL
GRN
R-BRN
RED
ORG
+
Descriminator
These echoes
are likely to be
Blue small fish.
YEL
Reddish-brown
Displayed in blue
since high freq.
echo is weaker.
BLU
Displayed in reddishbrown since high
freq. echoes are
red or reddish brown.
How the mix display works
1/1
LF
0
Low frequency display
Bottom zoom
display (LF)
HF
0.0
10
10
20
20
30
30
40
40
21
21
22
22
23.6 ft 23
23
User 2 display
1-10
0
0
High frequency display
Bottom zoom
display (HF)
1.5
Selecting Basic Range
The basic range may be selected with the [RANGE] switch from the eight ranges listed below.
(The default unit of depth measurement is feet.) These eight ranges may be programmed as
desired. For details, see page 3-7.
RANGE
30f
60f
120f
250f
500f
1000f
1600f
3000f
t
t
t
t
t
t
t
t
Range setting window (ex. feets)
Basic ranges (default setting)
Range Switch Position
Range Unit
1
2
3
4
5
6
7
8
Feet
30
60
120
250
500
1000
1600
3000
Meter
10
20
40
80
150
300
500
1000
Fathom
5
10
20
40
80
160
250
500
Hiro (Japanese)
6
12
25
50
100
200
300
600
Passi/Braza
6
12
25
50
100
200
300
600
Note1: This setting must be done within five seconds after rotating the [RANGE] switch once or
the range window will be erased.
Note2: Range for high and low frequencies can be set separately.
Note3: For how to select unit of depth measurement of depth, see page 3-3.
1-11
1.6
Shifting the Basic Range
The [-] and [+] keys determine the start depth of the picture. Start depth (shift) is shown at the
top of the screen. The shift value setting is reflected on all other range by default. This function
is not available when AUTO SHIFT is ON in DISP menu.
Shift the start
depth to watch
shallow or deep.
picture
Principle of shift
S H I F T
10 ft
10
Shift window (screen center), shift indication (top right corner)
Note1: This operation must be done within five seconds after pressing the [-] or [+] key or the
shift window will be erased.
Note2: The FCV-1200L/LM can automatically shift the display range to provide virtually
hands-free automatic operation. This can be done through the menu. For further details
see page 2-5.
Note3: You can set shift value independently for each range. See page 3-3.
1-12
1.7
Adjusting Gain
The [GAIN] control adjusts the sensitivity of the receiver. Adjust it so excessive noise just
disappears from the screen.
Gain too high
Gain proper
Gain too low
Examples of proper and improper gain levels
1.8
Measuring Depth
Use [!] or ["] key to place the VRM on the object to measure depth. Depth is digitally
displayed above the VRM.
Note: This operation is not available when the white marker window appears (by pressing the
[!] or ["] key). Select VRM at MARKER SELECT in DISP menu to use the VRM.
1/1
LF
0.0
0
0
VRM (Green)
20
Depth to VRM
39.8
40
60
49.6
ft
80
How to use the VRM
1-13
1.9
Marker Line
The [MARKER/TLL] key inscribes a vertical line when pressed. It may be used to denote a fish
school or other important echo.
At the same moment the key is pressed latitude and longitude position may be output to
connected navigation plotter and marked on its screen. (This feature requires a navigation
plotter.) For further details see TLL OUTPUT on page 3-16.
Elapsed time from the moment that the [MARKER/TLL] key is pressed may be displayed at the
upper-left corner of the screen. For details, see page 2-5.
1/1
Elapsed time from
when the
[MARKER/TLL] key
is pressed.
LF
0.0
0
0
0H00M
20
40
60
49.6
ft
80
Marker/TLL key function
1-14
Marker line
Shown in second color
from top of color bar in
16-color display; the top
color of color bar in 8-color
display.
1.10
Adjusting Clutter
When blue dots appear over the entire screen (mainly caused by dirty water), use the clutter
function to eliminate them.
1.
Rotate the [FUNCTION] switch to select CLUTTER.
The clutter menu appears.
C L U T T E R
HF•CLUTTER
HF•CURVE
LF•CLUTTER
LF•CURVE
: 4 (0
: STD
: 4 (0
: STD
7)
7)
Color changes
depending on
clutter level.
LOW
HIGH
Change echo color
assignment.
[-/+]: Change setting
[EXIT (knob)]: Exit
Clutter menu
•
•
For dual display
→
Go to step 2.
For other modes
→
Go to step 3.
2.
Press the [!] or ["] key to select HF CURVE or LF CURVE as appropriate.
3.
Press the [-] or [+] key to open the clutter curve selection window (default: STD).
STD
LINEAR CUSTOM
Clutter curve selection window
STD: The higher the clutter level the smaller weak echoes are displayed. (default setting)
LINEAR: The higher the clutter level the smaller all echoes are displayed.
CUSTOM: Applies the user clutter settings to the clutter menu.
4.
Press the [!] or ["] key to close the window.
5.
Press the [!] or ["] to select HF CLUTTER or LF CLUTTER as appropriate.
6.
Press the [-] or [+] key to set clutter rejection level. (0-7, 0 turns clutter rejector off.)
1-15
4
Clutter setting window
7. Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
Note: To use the user clutter setting menu setting is reflected on this function, select CUSTOM
at step 3.
1.11
Adjusting TVG
The TVG compensates for propagation loss of sound, so that the echoes from the same size
fish schools are displayed in the same color. Avoid excessive TVG; weak echoes may not be
displayed. The TVG is also useful for reducing surface noise.
0 ft
0 ft
100
100
How TVG works
1. Rotate the [FUNCTION] switch to select TVG.
The TVG menu appears.
TVG
HF·TVG LEV : 5 (0~10)
HF·TVG DIST : 600ft
LF·TVG LEV : 5 (0~10)
LF·TVG DIST : 600ft
0ft
This scale is
synchronized with the
distance value setting.
low
Gain
600
high ft
Adjust TVG effective
distance.
[-/+]: Change setting
[EXIT (knob)]: Exit
TVG menu
1-16
•
•
For dual display
→
Go to step 2.
For other modes
→
Go to step 3.
Note: When only the picture of the external equipment is displayed, an error message appears
on the menu.
2. Press the [!] or ["] key to select HF TVG DIST or LF TVG DIST as appropriate.
3. Press the [-] or [+] key to set the TVG available distance.
The larger the setting, the longer the range at which TVG works. The scale on the menu
synchronizes with the rate setting.
4. Press the [!] or ["] key to close the window.
5.
When surface noise appears in the range shallower than the setting range, press the [!]
key to select HF TVG LEV(EL) or LF TVG LEV(EL) as appropriate.
6. Press the [-] or [+] key to set the TVG level in the setting window (range: 0-10).
The higher the TVG level, the less the gain near distance.
5
TVG level setting window
7. Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
1-17
1.12
Eliminating Weak Echoes
Dirty water or reflections from plankton may be painted on the display in green or light-blue.
These weak echoes may be erased with the signal level function.
1.
Rotate the [FUNCTION] switch to select SIG LEVEL.
The SIGNAL LEVEL menu appears.
SIGNAL LEVEL
SIGNAL LEV : OFF
OFF
current
Echo colors
disappear from
weakest to
strongest.
Eliminate low
intensity echoes.
[-/+]: Change setting
[EXIT (knob)]: Exit
Signal level menu
2.
Press the [-] or [+] key to select the setting desired.
OFF 1 2 3 4 5 6 7 8 9
Signal level setting window (For 16 colors)
Every pressing of the [+] key deletes echoes from weakest to strongest in ascending order.
For eight colors, the setting window shows OFF, 1 to 4.
3.
Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
1-18
1.13
Picture Advance Speed
The ADVANCE/A-SCOPE function selects picture advance speed.
1.
Rotate the [FUNCTION] switch to select ADVANCE/A-SCOPE.
The PIC ADVNC/A-SCOPE menu appears.
PIC ADVNC/A-SCOPE
PIC ADVNC : 1/1
A-SCOPE
: OFF
For picture advance
and A-SCOPE setting.
[-/+]: Change setting
[EXIT (knob)]: Exit
PIC ADVNC/A-SCOPE menu
2.
Press the [-] or [+] key to select the speed desired.
STOP
1/16
1/8
1/4
1/2
1/1
2/1
3/1
4/1
Picture advance speed setting window
The fractions in the window mean the number of vertical scan lines produced per transmission.
For example, “1/2” means a vertical scan line is produced every two transmissions. These
fractions also appear at the top of the screen for your reference.
When selecting an advance speed, keep in mind that a fast advance speed will expand the size
of a fish school horizontally and a slow speed will contract it. The current speed appears at the
top of the display.
1/1 S
"S" means picture advance
speed is synchronized with
ship's speed.
See the next page.
Speed indication
3.
Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
1-19
Ship’s speed dependent mode
With speed data provided by a speed log, current indicator or navigation equipment, the display
advance speed may be set according to ship’s speed, the ship’s speed dependent mode. As
shown in the figure below the horizontal scale of the display is not influenced by the change of
ship’s speed, thus the speed-dependent picture advance permits judgement of fish school size
and abundance at any speed. The picture advance speed indication is suffixed with an “S” when
the ship’s speed dependent mode is active. For example, “1/1S.” For how to enable the ship’s
speed dependent mode see page 2-9. This function is available with ship’s speed of 2-20 kt.
Fish school is shrunk at high
ship's speed; expanded at
low ship's speed.
Normal Mode
Same size
fish schools
Speed
FULL SPEED
HALF SPEED
Fish schools are shown
same size regardless of
ship's speed.
Actual Movement
Ship's Speed Dependent Mode
How the ship’s speed dependent mode works
1-20
1.14
A-Scope Display
The A-scope picture displays echoes at each transmission with amplitudes and colors
proportional to their intensities on the right 1/4 of the screen. This feature is useful for close
observation of small fish and fish near the bottom,.
Note: For the dual mode display and vertical split screen, the A-scope display is available of the
high frequency only. In case of the horizontal split screen, high and low frequency A-scope
displays appear.
1.
Rotate the [FUNCTION] switch to select ADVANCE/A-SCOPE.
The PIC ADVNC/A-SCOPE menu appears.
2.
Press the ["] key to select A-SCOPE.
3.
Press the [+] key to select ON in the setting window.
OFF
ON
A-scope selection window
4.
Rotate the [FUNCTION] key to select EXIT.
To turn off the A-scope display, press the [-] key to select OFF at step 3 in this procedure.
1/1
LF
0
0
0.0
20
Single
frequency
A-scope Display
No responce
40
Weak echo (fish)
60
49.6
ft
Strong echo (bottom)
80
A-scope display
1-21
1.15
Suppressing Interference
Interference from other acoustic equipment operating nearby or other electronic equipment on
your boat may show itself on the display as shown in the figure below. You may suppress these
types of interference with the noise limiter.
Interference from
other sounder
Electrical interference
Interference
1.
Rotate the [FUNCTION] key to select NL.
The NOISE LIMITER menu appears.
NOISE LIMITER
HF·FREQ ADJ : +0.0%
-10
0
+10
HF·NOISE LIM : OFF
LF·FREQ ADJ : +0.0%
-10
0
The inverted solid
triangle shifts with
operation of [-] or
[+] key.
+10
LF·NOISE LIM : OFF
1. Shift frequencies to
reject interference.
2. Use LF/HF·NOISE LIM
in case interference
hasn't been rejected.
[-/+]: Change setting
[EXIT (knob)]: Exit
NL menu
•
•
For the dual display
→
Go to step 2.
For other modes
→
Go to step 3.
Note: When only the picture from external equipment is displayed, an error message appears
on the menu.
1-22
2.
Press the [!] or ["] to select HF•FREQ ADJ or LF•FREQ ADJ whichever is appropriate.
3.
Press the [-] or [+] key to set appropriate value in the setting window so that interference
disappears. (The setting range is -10.0% to +10.0%, however the lowest setting available
for the 68 and 200 kHz transducers is -4.5%.)
To adjust interference suppression level finely, go to step 4.
If the interference suppression is sufficient, go to step 7.
4.
Press the [!] or ["] key to close the setting window.
5.
Press the ["] key to select HF•NOISE LIM or LF•NOISE LIM whichever is appropriate.
6.
Press the [-] or [+] key to select the noise rejection setting in the setting window.
N3 provides the highest level of interference suppression.
OFF
N1 N2 N3
Signal level setting window
7.
Rotate the [FUNCTION] switch to select EXIT.
Note: Turn the noise limiter off when no interference exists, otherwise weak echoes may be
missed.
1-23
1.16
Adjusting the External Video Sounder Picture
The USER-1/USER-2 display can show the picture from external equipment, and you can adjust
the picture as below.
1.
Display the picture of the external equipment. “EXT” appears at the top of the screen.
2.
Rotate the [FUNCTION] switch to select GAIN-EXT.
The EXTERNAL (3 rd) ECHO menu appears.
EXTERNAL (3rd) ECHO
GAIN
: 5.0 (0
10)
CLUTTER
CURVE
: 4 (0
: STD
7)
TVG
STC
:5
:0
10)
10)
NOISE LIM
: OFF
GAIN ADJ
: +0 ( + 50)
TX PULSE
MANUAL
: STD
: 0.2 msec
(0
(0
These settings only
appear when the
picture from external
equipment is
displayed.
Optimize external (3rd)
echo presentation.
[-/+]: Change setting
[EXIT (knob)]: Exit
EXTERNAL (3 rd) ECHO menu
3.
Press the [!] or ["] to select the item to adjust.
4.
Press the [-] or [+] key to adjust.
5.
Press the [!] or ["] to close the window.
6.
Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
Items
GAIN: Adjusts gain (0.0-10.0)
CLUTTER: See page 1-15,
CURVE: See page 1-15
TVG: See page 1-16
STC: See page 2-9
NOISE LIM: Same as NOISE LIMITER. See page 1-22
GAIN ADJ: See page 2-9
TX PULSE, MANUAL: See page 2-10
1-24
2. MENU OPERATION
2.1
Basic Menu Operation
The main menu, consisting of the DISP (display), ALM (alarm), TX/RX, USER-1/2 and SYSTEM
menus, contains various items which once preset do not require frequent adjustment.
1.
Rotate the [FUNCTION] switch fully clockwise to select MENU.
The last-used menu among DISP, ALM, TX/RX, USER-1/2 and SYSTEM appears.
The illustration below shows the DISP menu.
Menu titles
Description for
selection.
DISP ALM TX/RX USER-1/2 SYSTEM
ZOOM MODE
: BOTTOM LOCK
NO. OF COLORS
HUE
BACKGROUND
WHITE LINE
:
:
:
:
16
STD
BLUE
OFF (OFF, 1~10)
DEPTH INFO
BOTTOM SEARCH
MARKER SELECT
AUTO SHIFT
:
:
:
:
STD
AUTO
VRM
OFF
DISPLAY DATA
SCROLL TIME
: TIMER
: OFF
SMOOTHING-1
:
SMOOTHING-2
: OFF
(OFF,1~8)
Menu for display setting.
[-/+]: Change set, [EXIT (knob)]: Exit
DISP menu
2.
Press the [!] key to select menu title area.
3.
Press the [+] or [-] key to select menu desired among DISP, ALM, TX/RX, USER-1/2 and
SYSTEM.
The menu selected is highlighted in the menu title area.
4.
Press the [!] or ["] key to select item. For example, select NO. OF COLORS.
Menu help for the item selected appears at the bottom of the screen.
5.
Press the [-] or [+] key to display the setting window. The illustration below shows the
selection window for NO. OF COLORS.
8
16
Selection window (ex. NO. OF COLORS)
2-1
cursor position in relation to the entire option range. This bar shifts with operation of [-] or [+] key.
Blue bar
CUSTOM STD HUE1 HUE2 HUE3 HUE4
The blue bar shows the current cursor position in
relation to the option range.
This bar shifts with operation of [-] or [+] key.
Selecting window (for item having several options, ex. HUE)
7.
Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
The menu disappears.
2-2
2.2
DISP Menu
DISP ALM TX/RX USER-1/2 SYSTEM
ZOOM MODE
: BOTTOM LOCK
NO. OF COLORS
HUE
BACKGROUND
WHITE LINE
:
:
:
:
16
STD
BLUE
OFF (OFF, 1~10)
DEPTH INFO
BOTTOM SEARCH
MARKER SELECT
AUTO SHIFT
:
:
:
:
STD
AUTO
VRM
OFF
DISPLAY DATA
SCROLL TIME
: TIMER
: OFF
SMOOTHING-1
:
SMOOTHING-2
: OFF
(OFF,1~8)
Menu for display setting.
[-/+]: Change set, [EXIT (knob)]: Exit
For picure advance speed: 2/1, 3/1, 4/1
For picture advance speed : 1/16, 1/8, 1/4, 1/2, 1/1
DISP menu
ZOOM MODE
Selects the zoom mode to show when the [MODE] switch selects ZOOM. Refer to Chapter 1.
NO. OF COLORS
Selects eight color or sixteen-color presentation.
HUE
Selects desired picture color. USER displays the colors programmed by the user. (See chapter
3.) STD is the standard colors used on most FURUNO video sounders. HUE 1-7 provide other
picture color arrangements.
BACKGROUND
Selects background color to black, dark blue, blue, light-blue or white. Note that the background
color is fixed when the user color (in HUE above) is selected.
WHITE LINE
Changes the strongest signal color to white. The higher the setting, the wider the white line.
Generally, fish schools on or close to the bottom are displayed on the screen as if they are small
rising of the bottoms. This feature can help discriminate bottom fish schools from the bottom.
2-3
DEPTH INFO
Changes the size and position of the depth indication.
BOTTOM SEARCH
On the dual frequency display, select transducer which is to measure depth. AUTO, automatic;
LOW, low frequency, HIGH, high frequency.
MARKER SELECT
Selects the marker function, VRM or WHITE MARKER.
VRM: Measures depth to an echo.
WHITE MARKER: The echo from a fish school or the bottom can be displayed in white.
(White marker operation)
1.
After the selecting EXIT with the [FUNCTION] switch to close the menu, press the [!] or ["]
key to show the white marker setting window.
WHITE MARKER
Color bar
The color selected
by this red arrow
changes to white.
OFF
/
: Select color
to enhance.
White marker setting window
2.
Press the [!] or ["] key to select the echo color which you want to emphasize.
The setting window disappears if there is no key operation within five seconds.
The color bar selected to display in white is displayed in white on the color bar.
Note: Before changing from WHITE MARKER to VRM, you must select OFF in the white marker
setting window.
2-4
AUTO SHIFT
Selects manual or automatic depth shift. The automatic shift function automatically locates the
bottom trace on the lower half of the screen; the range window jumps up where the bottom trace
rises over the center of the screen and jumps down when it reaches the bottom of the screen.
AUTO appears at the top right corner of the screen when the auto shift function is on. Note that
the [+] and [-] key are inoperative when the automatic shift function is turned on,
1/2
3/4
3/4
Range changes automatically to
locate the bottom on the lower half
of screen.
The equipment shifts to a deeper
range when the bottom comes to
the lower edge of the depth scale.
Automatic shift concept
DISPLAY DATA
Selects the data to display at the left top corner of the screen among OFF, L/L*, TD*, TIMER
(Elapsed time from the moment when the [MARKER/TLL] key is pressed), GAIN**, R/B* (range
and bearing to the waypoint) and COURSE*.
*: Requires navigation device.
**: The gain setting shown on the display may not agree exactly with GAIN controller position.
When you change the gain setting and then return correctly, using of the setting shown on
the display is recommended.
SCROLL TIME
Turns the display scroll time on/off. Scroll time displays, at the screen bottom, the amount of
time a scan line stays on the screen as it passes from one side of the screen to the other. Time
varies with the range and picture advance speed.
SMOOTHING-1
This setting can only be changed when the picture advance speed is set to 1/16, 1/8, 1/4, 1/2 or
1/1. (See page 1-19.) This function smoothes echo presentation. The higher the number, the
greater the smoothing. Adjust the setting when echoes appear “spotty.”
SMOOTHING-2
This setting can only be changed when the picture advance speed is set to 2/1, 3/1 or 4/1. (See
page 1-19.) This function smoothes echo presentation. Select ON when rough echoes appear.
2-5
2.3
ALM Menu
Sets the alarms; BOTTOM, FISH and TEMP (temperature). To silence the alarm beep, press the
[-], [+], [!] or ["] key.
BOTTOM ALARM
When your ship comes in the area of the selected depth, the beep sounds and the indication
BTM flashes at the top right corner to draw your attention.
FISH ALARM
FISH ALARM: Fish echoes of yellow or stronger colors (default setting) trigger the alarm.
BTM-FISH ALARM: When fish echoes come in the area which you set above the bottom, the
beep sounds and the indication FISH flashes at the top right corner of the screen. (Available
mode: bottom lock, discrim 1/2, discrim 1/3)
TEMP ALARM
Selects temperature range which triggers temperature alarm. Alarm is activated (beep sounds
and the indication TEMP appears at the top right corner of the screen) when water temperature
is above (UP) or below (DOWN) the preset value. This function requires a water temperature
sensor.
2.3.1
Setting the alarm
1.
Rotate the [FUNCTION] switch fully clockwise to select MENU.
2.
Press the [!] key to select the menu title area.
3.
Press the [-] or [+] key to select ALM to display the ALM menu.
2-6
DISP ALM TX/RX USER-1/2 SYSTEM
BOTTOM ALARM : OFF
ALARM DEPTH : 0 ft
*
ALARM ZONE : 10 ft
FISH ALARM
ALARM DEPTH
ALARM ZONE
ALARM LEVEL
: OFF
: 0 ft
: 10 ft *
: MID
TEMP ALARM
: OFF
TEMP LIMIT
: 65.0˚F(20~95)
*
ALARM ZONE : 1.0˚F
Menu for alarm setting.
[-/+]: Change set, [EXIT (knob)]: Exit
*: The setting is not available when ALARM
is OFF.
ALM (Alarm) menu
4.
Press the [!] or ["] key to select the alarm which you want to set.
5.
Press the [-] or [+] key to show the alarm setting window.
OFF
ON
Bottom alarm
OFF FISH
OFF WITHIN RANGE
BTM-FISH
Fish alarm
OUT OF RANGE
Temp alarm
Alarm setting window
6.
Press the [-] or [+] key to select the alarm type desired.
7.
Press the ["] key twice to select ALARM DEPTH (TEMP LIMIT for temp alarm).
8.
Press the [-] or [+] key to show the alarm setting window.
0 ft
Starting depth setting window (ex. Depth alarm)
9.
For BOTTOM ALARM and FISH ALARM, press the [-] or [+] key to set the starting point of
alarm zone.
Alarm marker appears (Depth alarm: green, Fish alarm: white).
2-7
Selected alarm
(flashing)
BTM
Alarm area
Start line
Alarm marker
Bottom alarm (green): right side
12.5
ft
Fish alarm (white): right side
Bottom-fish alarm (white): left side (vertical screen division)
right side (horizontal screen division)
Setting of alarm zone (ex. Bottom alarm)
10. Press the [] key to select ALARM ZONE.
11. Press the [-] or [+] key to show the alarm zone setting window.
10 ft
Alarm zone setting window (ex. Bottom alarm)
12. Press the [-] or [+] key to set the alarm zone.
For depth alarm and temp alarm, go to step 16. To set the fish alarm, go to step 13.
13. Press the [] key to select ALARM LEVEL.
14. Press the [-] or [+] key to show the level setting window.
MIN MID MAX
Level setting window
15. Press the [-] or [+] key to set the alarm level.
MIN: Alarm triggered against light-blue or stronger fish echoes.
MID: Alarm triggered against yellow or stronger fish echoes.
MAX: Alarm triggered against red or stronger fish echoes.
16. Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
To cancel an alarm, select OFF at step 6.
2-8
2.4
TX/RX Menu
DISP ALM TX/RX USER-1/2 SYSTEM
*1
*1
PRR LEVEL
:
<High Frequency>
STC
:
GAIN ADJ
:
RX BAND
:
TX PULSE
:
PULSE LENGTH :
<Low Frequency>
STC
:
GAIN ADJ
:
RX BAND
:
TX PULSE
:
PULSE LENGTH :
(0~20,S)
(0~10)
+
STD
STD
0.2msec (0.2~5.0)*2
(0~10)
+
STD
STD
0.2msec (0.2~5.0)*2
Menu for TX/RX setting.
[-/+]: Change set, [EXIT (knob)]: Exit
*1: FCV-1200L only
*2: The setting becomes available when
MANUAL is selected at TX PULSE.
TX/RX menu
PRR LEVEL
Changes pulse repetition rate. Normally, the highest rate (20) is used. When in shallow waters
second reflection echoes may appear between surface and actual bottom echo. In this case
lower the PRR level.
The choice “S” means the ship’s speed dependent mode, where the PRR changes
automatically with ship’s speed. (Requires ship’s speed input.) For further information about the
ship’s speed dependent mode, see page 1-20.
STC (High and Low Frequencies)
Adjusts STC level for the high and low frequencies, and is useful for suppressing surface noise.
The setting range is 0-10; the higher the setting the greater the extent of suppression. Setting
10 suppresses noise up to about 5 m. Turn off the STC when there is no noise on the screen,
otherwise weak echoes may be missed.
GAIN ADJ (High and Low Frequencies)
Adjusts gain (range: -50 to +50) of transceiver unit selected. Adjust the setting when the GAIN
control cannot effectively adjust the gain.
2-9
RX BAND (High and Low Frequencies)
Sets amplifier bandwidth of high and low frequency Rx amplifier.
When NARROW is selected, the noise suppression is greater however resolution is lower in
shallow water. Normally, set to STD. For more effective resolution, select WIDE.
TX PULSE (High and Low Frequencies)
Sets TX pulselength for high and low frequencies. The available choices are SHORT1,
SHORT2, STD, LONG, and MANUAL. Pulselength (without MANUAL) automatically changes
with range and shift.
PULSE LENGTH (High and Low Frequencies)
When selecting MANUAL on TX PULSE, this setting (setting range: 0.2 msec – 5.0 msec) is
active. The smaller digit, the greater the detection resolution; the larger digit, the longer the
detection range.
2-10
2.5
USER-1/2 Menu
Sets screen division for the dual frequency picture. This setting can be selected with USER-1, 2
of the [FUNCTION] switch. Default settings are as below.
USER-1:
( [LF]+[HF] +[MIX])
USER-2:
([LF]ZM/NOR+[HF]ZM/NOR)
DISP ALM TX/RX USER-1/2 SYSTEM
<USER 1>
SCREEN LAYOUT :
DISP MODE
: [LF]+[HF]+[MIX]
ZOOM MODE : BOTTOM ZOOM *1
<USER 2>
SCREEN LAYOUT :
DISP MODE
: [LF]Zm/Nor+[HF]Zm/Nor
ZOOM MODE : BOTTOM ZOOM
EXT DEVICE : ETR*2
DEFAULT SET : NO
Menu for user-preset mode setting.
[-/+]: Change set, [EXIT (knob)]: Exit
*1: The setting is available when Zm (Zoom)
is selected at the DISP MODE field.
*2: The setting is available when EX is
selected at the DISP MODE field.
USER-1/2 menu
SCREEN LAYOUT
Selects the screen division layout among the following patterns.
2-11
DISP MODE
Selects the picture to display in respective screen layout. See the Appendix 2 at the back of this
manual for detailed information.
[HF]:Normal
[LF]:Normal
[EX]:Normal*
[HF]:Zoom
[LF]:Zoom
[EX]:Zoom*
[MIX]:Normal
[LF]+[HF]:Zm/Nor
[LF]:Zm/Nor+[HF]
[EX]+[HF]:Zm/Nor*
[EX]+[LF]:Zm/Nor*
[EX]:Zm/Nor+[HF]*
[EX]:Zm/Nor+[LF]*
[EX]+[LF]+[HF]*
[MIX]+[LF]+[HF]
[LF]+[H]sub+[HF]
[L]sub+[LF]+[HF]
[HF]:Zm/Nor
[LF]:Zm/Nor
[EX]:Zm/Nor*
[LF]+[HF]
[EX]+[HF]*
[EX]+[LF]*
[LF]:Zm+[HF]:Zm
[HF]+[MIX]
[LF]+[MIX]
[H]sub+[HF]
[L]sub+[LF]
[LF]:Zm/Nor+[HF]:Zm/Nor
*: EXIF assy. (option) equipped for FCV-1200L,
INTERNAL selected at XDCR CONNECT
on the E/S DRAFT SETTING menu.
HF: high frequency
LF: low frequency,
NOR: normal
ZM: zoom,
MIX: mix
Sub: gain for fish and seabed echoes is raised
EX: display of external transducer unit or telesounder
Gain (sub)
The [GAIN] control mainly adjusts the bottom echo. When selecting the sub (sub gain), the
[GAIN] control adjusts the fish and bottom echoes. At the sub gain mode, press the [-] or [+] key
to show the sub gain setting window.
GAIN (SUB)
1.3
Sub gain setting window
Press the [-] or [+] key to select the setting value (0.0-10.0) within five seconds.
ZOOM MODE
Selects the zoom mode to use.
2-12
EXT DEVICE
Selects the equipment to use for EX in use mode EX of SCREEN LAYOUT. “EXT” appears at the
top of the screen.
ETR: External Transceiver Unit
TS/OTHER: telesounder, external echo sounder, sonar, picture recorder.
Note: When selecting
or
screen, the above equipment (low frequency echo)
should be connected to the EXT_H port. The EXT_L port signal cannot be displayed on
those screen layouts.
DEFAULT SET
Restores default settings of the user-1/2 menus. Select YES to restore default settings. Three
beeps sounds while default settings are being restored.
2-13
This page is intentionally left blank.
3. SYSTEM MENU
3.1
SYSTEM Menu Operation
1.
Rotate the [FUNCTION] switch fully clockwise to select MENU.
2.
Press the [!] key to select the menu title area.
3.
Press the [+] key to select SYSTEM to show the system menu.
DISP ALM TX/RX USER-1/2 SYSTEM
SYSTEM SETTING
ES / DRAFT SETTING
RANGE SETTING
TEMP SETTING
NET SONDE SETTING
USER COLOR SETTING
USER CLUTTER SETTING
NAV DATA SETTING
TARGET ECHO
TEST MODE
DEFAULT SETTING
Menu for system setting.
[+]: Go to setting [EXIT (knob)]: Exit
System menu
4.
Press the [!] or ["] key to select the item which you want to set.
5.
Press the [+] key to show the sub menu.
6.
Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
The system menu disappears.
3-1
3.2
SYSTEM SETTING Menu
This menu mainly sets picture layout parameters.
DISP ALM TX/RX USER-1/2 SYSTEM
SYSTEM SETTING
LANGUAGE
: ENGLISH
PICT ADV DIR : LEFT
DEPTH SCALE : RIGHT
DISP DIVISION :
ZOOM MARKER : ON
FREE SHIFT
: OFF
ECHO STRETCH : OFF
DEPTH UNIT
SPEED UNIT
TEMP UNIT
: ft
: kt
: ˚F
BOTTOM LEVEL :+0 (-40 ~ +0)
Select system language.
[-/+]: Change set, [EXIT (knob)]: Exit
SYSTEM SETTING menu
LANGUAGE
Selects the language, ENGLISH or JAPANESE. After making selection, rotate the [FUNCTION]
switch to select EXIT. This permits switching of language.
PICT ADV DIR
Selects picture advance direction to left, right or left/right which advances the picture in both
right and left directions from the screen center.
DEPTH SCALE
Selects where to position the depth scale; right, center or off.
DISP DIVISION
Sets screen division for the dual picture.
divides the screen.
3-2
vertically divides the screen;
horizontally
ZOOM MARKER
Turns zoom marker on/off.
FREE SHIFT
Set shift value independently for each range (ON) or commonly for all range (OFF).
ECHO STRETCH
Displays the strong echoes long though the pulse length setting is short. It is useful for
distinguishing individual fish (e.x. squid) in plankton.
DEPTH UNIT
Selects unit of depth measurement; meters, feet, fathoms, hiro (Japanese), passi/braza.
SPEED UNIT
Selects unit of ship’s speed; kt, km/h, sm/h.
TEMP UNIT
Sets unit of water temperature measurement; Celsius or Fahrenheit.
BOTTOM LEVEL
1/1
5
When seabed depth readout is unstable,
use this feature to stabilize it. The
LF
0
00
Bottom lock display
setting range is -40 to 0, and the default
4
10
setting is 0.
3
If this setting value is too small, fish
20
echo may be regarded as bottom which
2
causes unstable depth readout.
30
1
Set the bottom
search so that this
line disappears.
0
40
Seabed
3-3
3.3
ES/DRAFT SETTING Menu
This menu sets up the transducer and ship’s draft.
DISP ALM TX/RX USER-1/2 SYSTEM
ES/DRAFT SETTING
*
<High Frequency>
XDCR CONNECT
TX POWER
DRAFT
FREQ CHOICE
: INTERNAL
: MAX
: +0.0 ft (-15
: 75 kHz
*
<Low Frequency>
XDCR CONNECT
TX POWER
DRAFT
FREQ CHOICE
:INTERNAL
: MAX
: +0.0 ft (-15
: 22 kHz
E/S SIG OUT
KP SETTING
: OFF
: INTERNAL
+90)
+90)
Select transducer connected.
[-/+]: Change set, [EXIT (knob)]: Exit
*: FCV-1200L only
ES/DRAFT SETTING menu
XDCR CONNECT (High and Low Frequencies)
Sets the video sounder to be used for the high and low frequencies, as follows.
INTERNAL: Use the internal video sounder signal (FCV-1200L only).
ETR: Use the video sounder signal from the external Transceiver unit (FCV-1200LM and
FCV-1200L with optional EXIF assy. only).
TS/OTHER: Use the video sounder signal from the external telesounder, video sounder or
sonar (FCV-1200LM and FCV-1200L with optional EXIF assy. only).
Note: Choose INTERNAL when selecting LF, HF or LF/HF at the ES SIG OUT described on the
next page.
TX POWER (High and Low Frequencies)
Reduces the power output on high and low frequency (FCV-1200L only). <P/R> appears at the
bottom of the screen when MIN is selected. When interference from near another shipborne
transducer occurs, set this item appropriately. (MAX→1/2→ 1/4→ 1/8→ 1/16→MIN)
3-4
DRAFT
Sets the ship’s draft, to show the depth between the sea surface and the bottom (rather than
from transducer to bottom). When the picture recorder MT-12 is used to replay the recording
data, set the draft to –2.0 ft.
FREQ CHOICE
You can select the transmitting frequencies for the following transducers. Select the frequency to
use on this menu.
This function is useful when there is interference from other vessel, or when targeting certain fish
species.
50kHz/75kHz transducer
Using the following transducers with 75 kHz provides high resolution.
•
•
•
•
•
50B-6
50/200-1T (50kHz)
50/200-1ST(50 kHz)
50B-9
50B12
88 kHz/22 kHz transducer
Using the following transducer with 22 kHz frequency enables long range detection, a
characteristic of low frequency.
•
88B-10
Note: When the above transducers are used with 75 kHz or 22 kHz, the transmission line may
be longer slightly.
3-5
E/S SIG OUT
Outputs selected video sounder signal to external equipment. Default setting is OFF (no output).
In the following cases, the optional EXIF assy. is required for FCV-1200L.
•
•
•
When telesounder is connected on sister ship.
When recording video sounder signal by picture recorder.
When FCV-1200L outputs video sounder signal to other color video sounder.
LF: Outputs the low frequency signal.
HF: Outputs the high frequency signal.
LF/HF: Outputs both the high and low frequency signals.
Note: When selecting LF, HF, or LF/HF, select INTERNAL at XDCR CONNECT.
Equipment connected
XDCR CONNECT
External transceiver unit
ETR
Telesounder on sister ship
INTERNAL
Telesounder on master
ship
TS/OTHER
Record by picture recorder
INTERNAL
Play back by picture
recorder
TS/OTHER
Outputs to other E/S
INTERNAL
E/S SIG OUT
Remarks
LF, HF, LF/HF
Not available on FCV1200LM
LF, HF, LF/HF
Not available on FCV1200LM
LF, HF, LF/HF
Not available on FCV1200LM
KP SETTING
Synchronizes transmission with other echo sounders. Select EXTERNAL to synchronize
transmission.
3-6
3.4
RANGE SETTING Menu
This menu allows the user to preset the range selected with the [RANGE] control.
DISP ALM TX/RX USER-1/2 SYSTEM
RANGE SETTING
RANGE1
RANGE2
RANGE3
RANGE4
RANGE5
RANGE6
RANGE7
RANGE8
M/Z RANGE
B/L RANGE
: 30 ft (16
: 60 ft
: 120 ft
: 250 ft
: 500 ft
: 1000 ft
: 1600 ft
: 3000 ft
: 16 ft (16
: 16 ft
6000)
600)
SPLIT RANGE: OFF
Set preset range scales.
[-/+]: Change set, [EXIT (knob)]: Exit
RANGE SETTING Menu
Note: Hiro is the Japanese unit of depth measurement.
RANGE1-RANGE8
Presets basic ranges for the [RANGE] switch. (5-2000 m, 16-6000 ft, 2-1200 fa, 4-1600 hiro, 31200 P/B)
M/Z RANGE
Sets display range of marker zoom and bottom zoom pictures. (5-200 m, 16-600 ft, 2-120 fa,
4-160 hiro, 3-120 P/B)
Note: For the vertical split screen, halve the above values.
B/L RANGE
Sets display range of bottom-lock, discrim-1/2, discrim-1/3 picture. (5-200 m, 16-600 ft, 2-120 fa,
4-160 hiro, 3-120 P/B)
Note: For the vertical split screen, halve the above values.
3-7
SPLIT RANGE
Select ON to set range for low frequency and high frequency individually.
1.
Rotate the [RANGE] switch to show RANGE (LF or HF) window.
RANGE [LF]
30
60
120
250
500
1000
1600
3000
ft
ft
ft
ft
ft
ft
ft
ft
RANGE [HF]
Switch [LF] and [HF] by
pressing the [RANGE]
switch.
30
60
120
250
500
1000
1600
3000
ft
ft
ft
ft
ft
ft
ft
ft
Range window
2.
Press the [RANGE] switch within five seconds to display the RANGE (LF) window or
RANGE (HF) window whichever desired.
3.
3-8
Rotate the [RANGE] switch to select the range desired.
3.5 TEMP SETTING Menu
This menu sets up water temperature sensor.
DISP ALM TX/RX USER-1/2 SYSTEM
TEMP SETTING
TEMP INPUT
TEMP ADJUST
: SENSOR
: +0.0 F(-20
+20)
TEMP READOUT : ON
TEMP GRAPH
: OFF
TEMP COLOR
: STD
Select temperature sensor.
[-/+]: Change set, [EXIT (knob)]: Exit
TEMP SETTING menu
TEMP INPUT
Selects source of water temperature data; net sonde, sensor, NMEA or CIF.
TEMP ADJUST
Offsets water temperature indication to improve accuracy. Effective only for net sonde and water
temperature sensor. (-20.0 to +20.0°F in 0.1 step)
TEMP READOUT
Turns on/off water temperature indication.
TEMP GRAPH
Turns on/off temperature graph and selects graph scale.
OFF: No water temperature graph
NARROW: Graduation every 2°
STD: Graduation every 2.5° (default setting)
EXPAND: Graduation every 5.0°
TEMP COLOR
Selects the color of the temperature graph (standard, white, red, black, yellow).
Note: Standard means the fifth color from the bottom of the color bar, including background
color in 16-color display; third color in 8-color display. Yellow means tenth (8-color display: sixth)
color from the bottom of the color bar.
3-9
3.6
NET SONDE SETTING Menu
This menu sets up the Net Sonde.
DISP ALM TX/RX USER-1/2 SYSTEM
NET SONDE SETTING
SONDE MARK
COLOR
WIDTH
: OFF
:1
:2
SONDE GRAPH : OFF
GRAPH MODE : SURFACE
GRAPH WIDTH : 1/4
GRAPH RESET : NO
Indication of sonde mark.
[-/+]: Change set, [EXIT (knob)]: Exit
NET SONDE SETTING menu
SONDE MARK
Selects where to display the sonde mark; HIGH frequency picture, LOW frequency picture or
OFF.
1/1
LF
0
0
0.0
20
40
Sonde mark
60
COLOR
Selects number of colors to display net sonde mark; 1 (14 level color), 2 (12 level color) or 3 (10
level color).
WIDTH
Selects the width of sonde mark; 2 dots, 3 dots, 4 dots or 5 dots.
3-10
SONDE GRAPH
Turns on/off the net sonde water temperature graph.
10
15
20
0
5
10
Water temperature
graph
Horizontal lines
show depth.
Net sonde water temperature graph (at the left-hand side of display)
GRAPH MODE
Selects the display starting position of the net sonde water temperature graph. SURFACE is the
first-water temperature (surface condition); BOTTOM the last-written water temperature (net
sonde position). The display range is 12 °C and scale interval is 5 °C. For example, if the surface
water temperature is 18 °C, the first temperature scale would be 10 °C-20 °C and the display
range is 9 °C-21 °C. If the water temperature drops by 9 °C, for example, the next temperature
scale would be 0 °C to 10 °C and the display range –1 °C to 11 °C.
3-11
Scale (5 C)
Display Range(12 C)
10
0
15
5
20
10
Surface
15
20
25
5
10
15
Scale shifts with
temperature
Bottom
Net sonde water temperature graph (SURFACE/BOTTOM)
GRAPH WIDTH
Selects the width of sonde water temperature graph; 1/4 of the screen or 1/2 of the screen.
Note: When turning on both of sonde water temperature graph and A-scope, 1/2 is not available.
GRAPH RESET
Select ON to reset the graph.
3-12
3.7
USER COLOR SETTING Menu
In addition to the standard and factory programmed color sets, the user may set and store
display colors as desired and recall them from the DISP menu.
DISP ALM TX/RX USER-1/2 SYSTEM
USER COLOR SETTING
COLOR NO.
:
BKGD
RED
GREEN
BLUE
: 0 (0
:2
:9
15)
DEFAULT SET: NO
Color setting for 16-color presentation.
[-/+]: Change set, [EXIT (knob)]: Exit
USER COLOR SETTING menu
1.
Press the [-] or [+] key to show the color setting window.
BKGD ECHO1 ECHO2 ECHO3 ECHO4 ECHO5 ECHO6 ECHO7
Color setting window (in case of 16 colors)
2.
Press the [-] or [+] key to select the color to change (background, color 1-14* and the
strongest color).
*: In case of eight colors, color is 1-6.
ECHO15
ECHO14
ECHO13
ECHO12
ECHO11
ECHO10
ECHO9
ECHO8
ECHO7
ECHO6
ECHO5
ECHO4
ECHO3
ECHO2
ECHO1
BKGD
Color bar (in case of 16 colors)
3-13
3.
Press the [!] or ["] key to close the color setting window.
4.
Press the ["] key to select RED, GREEN or BLUE (level).
5.
Press the [-] or [+] key to show the level setting window.
0
Level setting window
6.
Press the [-] or [+] key to select color strength.
The higher the number, the darker the color.
7.
Press the [!] or ["] key to close the level setting window.
8.
Do steps 4-7 to adjust other color..
9.
To return to original color, select YES at DEFAULT SET.
3-14
3.8
USER CLUTTER SETTING Menu
The USER CLUTTER SETTING menu lets you emphasize weak to medium strength echoes.
The settings of this menu are active when selecting CUSTOM on the CLUTTER menu.
DISP ALM TX/RX USER-1/2 SYSTEM
USER CLUTTER SETTING
COLOR-7
COLOR-6
COLOR-5
COLOR-4
COLOR-3
COLOR-2
COLOR-1
BACKGROUND
:
:
:
:
:
:
:
:
3 (1 14)
3
3
3
3
3
3
3
DEFAULT SET
: NO
The larger setting
value, the wider
ratio of the color
selected.
When the value is not suitable,
weak level is automatically adjusted.
Set clutter level to be displayed.
[-/+]: Change set, [EXIT (knob)]: Exit
USER CLUTTER SETTING menu
1.
Press the [!] or ["] key to select color or background to change. COLOR-7 is the strongest
color.
2.
Press the [-] or [+] key to show the setting window.
0
Setting window
3.
Press the [-] or [+] key to set the level (1-14).
If
then
you want to emphasize COLOR-7 (reddish
brown, red)
COLOR-7, COLOR-6: set large value.
COLOR-5 to COLOR-1: set small value.
you want to emphasize middle color (yellow,
green)
COLOR-7 to COLOR-5: set small value.
COLOR-4 and COLOR-3: set large value.
COLOR-2 and COLOR-1: set small value.
you want to remove the weakest color
COLOR-1: set small value.
4.
Press the [!] or ["] key to close the setting window.
5.
Repeat steps 1 through 4 to set other color.
To return to default setting, select YES at DEFAULT SET.
3-15
3.9
NAV DATA SETTING Menu
This menu selects source of position data and heading data.
DISP ALM TX/RX USER-1/2 SYSTEM
NAV DATA SETTING
SPEED INFO
: OFF
NMEA VERSION : Ver 2.0
NAV DATA
: AUTO
COURSE : TRUE
TLL OUTPUT
: OFF
Indication of speed data.
[-/+]: Change set, [EXIT (knob)]: Exit
NAV DATA SETTING menu
SPEED INFO
Turns on/off the ship’s speed indication.
NMEA VERSION
Selects NMEA version of external equipment; Ver 1.5, Ver 2.0 or SPECIAL. If you are not sure
of version number try both and select which one successfully receives data. SPECIAL outputs
the depth data with 600 bps.
NAV DATA
Selects source of navigation data (NMEA talker); Loran C, Loran A, Decca, GPS, DR or AUTO.
Select AUTO when more than one talker data is input. The order of priority is GPS, Loran C,
Loran A, Decca DR.
COURSE
Selects heading reference; TRUE or MAG (magnetic bearing).
TLL OUTPUT
Enables/disables output of L/L position to a navigation plotter when the [MARKER/TLL] key is
pressed.
3-16
3.10
TARGET ECHO SETTING Menu
The TARGET ECHO menu sets equipment objective. Four choices are available: NORMAL,
SURFACE, SQUID and DEEP SEA.
DISP ALM TX/RX USER-1/2 SYSTEM
TARGET ECHO
TARGET ECHO : NORMAL
SURFACE is valid when proper
transducer is connected.
Select target echo to optimize
sounding parameters.
[-/+]: Change set, [EXIT (knob)]: Exit
TARGET ECHO menu
Note: Select SURFACE only when both of the transducers (1 kW) below are used. The
SURFACE can be used to detect small surface fish. The pulse repetition rate is greater than
NORMAL.
•
•
•
•
•
•
•
50/200-1ST
50/200-1T
200B-5S
50B-6
50B-9/9B
50B-8G
50/200/400
3-17
This page is intentionally left blank.
4. INTERPRETING THE DISPLAY
This section provides, using typical examples, information necessary for interpreting the display.
1/1
LF
0.0
Surface
noise
0
0
Zero line
20
Color bar
Fish school
40
Bottom
60
49.6
ft
80
Typical display
4.1
Color Bar
The color bar shows the relation between echo intensity and echo color on the screen. The top
color (reddish brown) is the strongest color and the lower colors the weakest. The bar can be
used as a reference to estimate density of a fish school, fish species and hardness of the
bottom. The background color can be selected on the menu screen.
STRONG
WEAK
R-BRN
RED
ORANGE
YELLOW
GREEN
LIGHT-BLUE
BLUE
DEEP BLUE
No Signal
49.6
ft
Color bar
4-1
4.2
Zero Line
The zero line represents the transducer’s position. It moves off the screen when a shifted range
is used, or is shown at draft depth when ship’s draft is entered.
Zero Line
Range shifted
Zero line
4.3
Bottom Echoes
Bottom echoes are normally strongest and displayed in reddish brown or red, but colors and
width will vary with bottom material, depth, sea condition, installation, frequency, pulselength
and sensitivity.
Bottom profile
A hard and rough bottom appears with a longer tail because it reflects more of the ultrasonic
pulse. Because of their stronger return, shallow echoes appear wider than deep ones even
when all botom conditions are equal. Also, a longer bottom tail appears on slopes because of
the difference in traveling time at both edges of the beam angle. In the rugged bottom, echoes
are reflected on many different planes, overlapping to present a 3D effect.
Color difference
Rugged
bottom
Second bottom
echo
Bottom material and bottom profile
4-2
Bottom nature
The nature of the bottom is known from the intensity and length of the bottom tail. Generally,
when observing the bottom nature, the lower sounding frequency is used, the pulselength is set
to long, and the gain setting is not disturbed. In the hard and craggy bottom, the bottom appears
more reddish and with a long tail. However, the bottom with a sediment may give a short tail if a
low frequency sounding is used.
Rock base
Mud & sand
Bottom nature
4.4
Fish Schools
Fish quantity
Fish quantity can be estimated to a certain extent from fish echoes on the screen if fish school
size and fish school density are kept in mind.
Fish school size
Usually the size of fish echoes on the screen is proportional to the actual size of the fish school.
However, if two fish echoes appear at different depths with the same size, the fish school at
shallower depth is smaller because the ultrasonic beam widens as it propagates and a fish
school in deep water is displayed larger.
Deep fish school sounding time
Shallow fish school sounding time
Large
school
Size of
fish school
School depth
and sounding
time
Small
school
Fish school size
Difference of fish school sounding times
4-3
Fish school density
If two fish scools appear with the same color at different depths, the one in deeper water is
denser because the ultrasonic wave attenuates as it propagates and the fish school in deep
water tends to be displayed in a weaker color.
Fish Echo
Less Reddish
(Sparse echo)
Reddish
(Dense echo)
Difference in
signal strength
Strong
Echo
Weak Echo
Fish school density
4.5
Other Echoes
Plankton
A plamkton layer, a likely place to find fish, is displayed in green or blue dots. It usually descends
in the day and rises at night.
Plankton
Fish School
Plankton
Current rip
When two ocean currents meet with different speeds, directions and water temperatures, a
current rip develops. A current rip’s on-screen appearance is as shown below.
Current Rip
Current rip
4-4
Surface noise
When the sea is rough or the ship passes over a wake, surface noise may appear at the top of
the screen. It can be suppressed with the CLUTTER function.
Surface Noise
Surface noise
Aerated water
When the sea is rough or the ship makes a quick turn, gaps in the bottom echo on the screen
may appear. This is caused by air bubbles which block propagation of the sound wave.
Generally low frequency ultrasonic waves are interrupted more easily than high ones.
Ultrasonic wave
blocked by aerated
water
Aerated water
False image
Every time the ultrasonic pulse is transmitted, some radiation escapes on each side of the beam,
called “side lobes.” Echoes from side lobes show on the display as false images as below.
Main
Lobe
False Image
Side
Lobe
False images
4-5
This page is intentionally left blank.
5. MAINTENANCE &
TROUBLESHOOTING
WARNING
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
5.1
Maintenance
Regular maintenance is important for continued performance. Important points to be checked
from time to time are shown below.
Check point
Action
Interval
Transducer cable
If conductors are exposed, replace cable.
Monthly
Power cable plug, transducer cable plug
If loosened, secure tightly.
Monthly
Grounding
If corroded, clean.
Monthly
Ship’s mains voltage
If out of ratings, correct problem.
Monthly
Transducer cleanliness
Marine life on the transducer will result in a
gradual decrease in sensitivity. Check the
transducer face each time the boat is
drydocked. Carefully remove any marine
life with piece of wood or fine sandpaper.
At
dry-dock
Display unit cleanliness
Dust or dirt may be removed with a soft
cloth. Water-diluted mild detergent may be
used if desired. DO NOT use chemical
cleaners to clean the display unit; they
may remove paint and markings.
LCD screen
Wipe the LCD carefully to prevent
scratching, using tissue paper and an LCD
cleaner. To remove dirt or salt deposits,
use an LCD cleaner, wiping slowly with
tissue paper so as to dissolve the dirt or
salt. Change paper frequently so the salt
or dirt will not scratch the LCD. Do not use
solvents such as thinner, acetone or
benzene for cleaning.
As
necessary
5-1
5.2
Fuse Replacement
A fuse in the display unit and processor unit protects the equipment against overcurrent and
reverse polarity of the ship’s mains or internal fault. If a fuse blows find the cause before
replacing it.
CAUTION
Use the proper fuse.
Use of a wrong fuse can cause fire or
equipment damage.
Location of fuse
Replacement
Type
On the circuit board in the
display unit
Contact your dealer.
FGMB 3A 125VAC
In the processor unit
Unscrew the fuse holder on
the processor unit to replace
fuse. If the fuse blows again
after replacement, contact
your dealer.
FGMO 15A 125VAC
5-2
5.3
Troubleshooting
This section provides simple troubleshooting procedures which the user may follow to restore
normal operation.
If…
there are no echoes but the scale appears
there is no zero line or zero line is not in correct
position
Then…
•
•
•
you suspect low sensitivity
the bottom is traced in zigzag pattern or you
experience occassional loss of echo
•
•
•
there is no depth readout
•
•
automatic shift is inoperative
•
picture is distorted
•
color is strange in a given area
occasional noise is seen
•
•
there is noise and interference
•
•
•
check if the transducer is properly connected.
check if the range shifted. (Zero line does not
appear when the range is shifted.)
press the [-] key so as the scale appears from
0.
check that gain control is properly set.
the sea may be rough. Bottom is traced zigzag
when the sea is rough.
own boat may have passed over other boat’s
wake, which blocks propagation of sound wave.
check to see if bottom is present on the normal
picture range.
check if bottom echo is strong enough (red,
reddish brown in color).
check if bottom echo is strong enough (red,
reddish brown in color)
check if magnetic field generating equipment
(transformer, rectifier) are nearby.
check if a magnet is near the equipment.
check if the cables of pulse generating
equipment are near the equipment.
check that GAIN and CLUTTER properly
adjusted.
check the setting of the noise limiter.
check the equipment’s ground.
5-3
5.4
Diagnostic Test
The diagnostic test checks the equipment for proper operation.
1.
Rotate the [FUNCTION] switch fully clockwise to select MENU.
2.
Press the [!] key to select the menu title area at the top of screen.
3.
Press the [+] key to select SYSTEM.
4.
Press the [!] or ["] key to select TEST.
5.
Press the [+] key to open the test menu.
DISP ALM TX/RX USER-1/2 SYSTEM
TEST MODE
DIAGNOSTICS : NO
TEST PATTERN : NO
Press and hold [MARKER] key more than
3 sec to exit from TEST MODE.
Menu for diagnostics.
[-/+]: Change set, [EXIT (knob)]: Exit
Test menu
6.
Press the [+] key twice to select YES in the setting window.
The test screen appears.
[
] : NO
[
] : YES
Test setting window
5-4
Program No.
Panel Unit
RO M
S R A M
D R A M
E S 1
E S 2
E X I F
N M E A
SONDE (CIF)
Temp. SENSOR
Temp. SONDE
0252296-0XX
Ver XX OK
OK
OK
OK
OK 15-200*
OK 15-200*
OPEN
OK
OK
+32.6˚F
+31.6˚F
*
0
0
0
0
0
0
8
0
0
5
61
86
Press and hold [MARKER] key more than 3 sec to exit.
XX: Version No.
*: Frequency from the transducer connected.
•
•
ROM, SRAM, DRAM test results are shown as OK or NG (No Good).
ES1, ES2: ES1/2 Board connection test results are shown as OK or OPEN. (For
FCV-1200LM, OPEN only.) When test result is OK, the frequency of ES Board appears;
15-200 or 400.
•
•
EXIF: Test results are shown as OK or OPEN (no EXIF assy connection). For FCV-1200LM,
OK appears.
NMEA*, SONDE (CIF)* test results are shown as OK. Nothing appears in case of error or no
connection. *requires special test connector.
Panel test
The “Panel” column at the right of the diagnostics display is used to check keys and controls.
1.
Press any key except the [POWER] key. The pressed key’s on-screen location changes
from 0 to 1 when the key is pressed.
2.
Operate the controls. For the controls the figure on the screen changes as below.
[FUNCTION] :1 to 8
[RANGE] :
0 to 20
[MODE] :
1 to 7
[GAIN] :
0 to 127
3.
Press the [MARKER/TLL] key more than three seconds to return to the SYSTEM menu.
4.
Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
5-5
5.5
Test Pattern
The test pattern tests for proper display of colors.
1. Rotate the [FUNCTION] switch fully clockwise to select MENU.
2. Press the [] key to select the menu title area at the top of the screen.
3. Press the [+] key to select SYSTEM.
4. Press the [] or [] key to select TEST.
5. Press the [+] key.
6. Press the [+] key to select TEST PATTERN.
7. Press the [+] key twice to select YES in the dialog box.
[
] : NO
[
] : YES
Test pattern selection dialog box
8. Press the [+] key to change the test pattern.
The test pattern changes in the sequence below.
16 tones
of RED
16 tones
of GREEN
16 tones
of BLUE
WHITE
RED
BLACK
BLUE
GREEN
Test pattern sequence
9. Press the [MARKER/TLL] key more than three seconds to return to the system menu.
10. Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
5-6
5.6
Default Setting
The memory (all menu settings) can be cleared to start afresh. All default menu settings are
restored when the memory cleared. For your reference all default settings are shown in the
menu tree at the back of this manual.
Note: User color setting, language, target echo setting and user clutter setting are not
disturbed.
1. Rotate the [FUNCTION] switch fully clockwise to select MENU.
2. Press the [] key to select the menu titles at the top of the menu.
3. Press the [+] key to select SYSTEM.
4. Press the [] key to select DEFAULT SETTING.
5. Press the [+] key to show the DEFAULT SETTING menu.
DISP ALM TX/RX USER-1/2 SYSTEM
DEFAULT SETTING
DEFAULT SET : NO
[-/+]: Change set, [EXIT (knob)]: Exit
Default setting menu
6. Press the [+] key twice to select YES in the selection window.
[
] : NO
[
] : YES
Selection window
Alarm beeps three times while the memory is being cleared.
7. Rotate the [FUNCTION] switch fully counterclockwise to select EXIT.
5-7
This page is intentionally left blank.
APPENDIX 1
MENU TREE
[FUNCTION] switch
CLUTTER
HF CLUTTER (0-7, 4)
HF CURVE (STD, LINEAR, CUSTOM)
LF CLUTTER (0-7, 4)
LF CURVE (STD, LINEAR, CUSTOM)
TVG
HF TVG LEV (0-10, 5)
Underline: default setting
HF TVG DIST (100ft-3000ft, 600ft)
LF TVG LEV (0-10, 5)
LF TVG DIST (100ft-3000ft, 600ft)
SIG LEVEL
SIGNAL LEV (OFF, 16 colors: 1-9, 8 colors: 1-4)
ADVANCE/A-SCOPE
PIC ADVNC (STOP, 1/16, 1/8, 1/4, 1/2, 1/1, 2/1, 3/1, 4/1)
A-SCOPE (OFF, ON)
NL
*1
HF FREQ ADJ (-10.0-+10.0% , +0.0%)
HF NOISE LIM (OFF, N1, N2, N3)
LF FREQ ADJ (-10.0-+10.0, +0.0)
LF NOISE LIM (OFF, N1, N2, N3)
GAIN-EXT
*1: For 68 and 200 kHz transducers,
the setting range is -4.5 to +10.0%)
GAIN (0.0-10.0, 5.0)
CLUTTER (0-7, 4)
CURVE (STD, LINEAR, CUSTOM)
TVG (0-10, 5)
STC (0-10, 0)
*2
NOISE LIM (OFF, N1, N2, N3)
GAIN ADJ (-50-+50, +0)
TX PULSE (SHORT1, SHORT2, STD, LONG, MANUAL)
PULSE LENGTH (0.2msec-5.0msec, 0.2msec)
*2: Only when the picture from the external equipment is displayed.
MENU
1
(Continued on the next page.)
AP-1
(Continued from previous page)
1
DISP
ZOOM MODE (BOTTOM LOCK, BOTTOM ZOOM,
MARKER ZOOM, DISCRIM-1/2, DISCRIM-1/3)
NO. OF COLORS (8, 16)
HUE (CUSTOM, STD, HUE1-7)
BACKGROUND (BLACK, DARKBLUE, BLUE, LIGHTBLUE, WHITE)
WHITE LINE (OFF, 1-10)
DEPTH INFO (OFF, STD, LARGE, RIGHT)
BOTTOM SEARCH (AUTO, LF, HF)
MARKER SELECT (VRM, WHITE MARKER)
AUTO SHIFT (OFF, ON)
DISPLAY DATA (OFF, L/L, TD, TIMER, GAIN,
R/B, COURSE)
SCROLL TIME (OFF, ON)
SMOOTHING-1 (OFF, 1-8, 3)
SMOOTHING-2 (OFF, ON)
ALM
BOTTOM ALARM (OFF, ON)
ALARM DEPTH (0-6000ft, 0ft)
ALARM ZONE (1-6000ft, 10ft)
FISH ALARM (OFF, FISH, BTM-FISH)
ALARM DEPTH (FISH: 0-6000ft, 0ft)
(BTM-FISH: 0.0-600.0ft, 0.0ft)
ALARM ZONE (FISH:1-6000ft, 10ft)
(BTM-FISH:0.1-600.0ft, 1.0ft)
ALARM LEVEL (MIN, MID, MAX)
TEMP ALARM (OFF, WITHIN RANGE, OUT OF RANGE)
TEMP LIMIT (20.0-95.0, 65.0 F)
ALARM ZONE (0.1-30.0, 1.0 F)
(Continued on the next page)
AP-2
(From the previous page)
TX/RX
PRR LEVEL (0-20, S, 20)
STC (0-10, 0)
GAIN ADJ (-50-+50, +0)
RX BAND* (NARROW, STD, WIDE)
TX PULSE (SHORT1, SHORT2, STD, LONG, MANUAL)
PULSE LENGTH (0.2msec-5.0msec, 0.2msec)
HF and LF should be set.
*: FCV-1200L only
USER-1/2
USER-1
SCREEN LAYOUT (
)
([HF]:Normal, [LF]:Normal, [Ex]:Normal*
DISP MODE
[HF]:Zoom, [LF]:Zoom, [Ex]:Zoom*, [Mix]:Normal)
([HF]:Zm/Nor, [LF]:Zm/Nor, [Ex]:Zm/Nor*,
[LF]+[HF], [Ex]+[HF]*, [Ex]+[LF]*, [LF]Zm+[HF]Zm,
[HF]+[Mix], [LF]+[Mix], [H]sub+[HF], [L]sub+[LF])
([LF]+[HF]:Zm/Nor, [LF]:Zm/Nor+[HF], [Ex]+[HF]:Zm/Nor*,
[Ex]+[LF]:Zm/Nor*, [EX]:Zm/Nor+[HF]*, [EX]:Zm/Nor+[LF]*,
[Ex]+[LF]+[HF]*, [LF]+[HF]+[Mix],
[LF]+[H]sub+[HF], [L]sub+[LF]+[HF])
([LF]Zm/Nor+[HF]Zm/Nor)
*: FCV-1200L equipped with EXIF Assy.,
INTERNAL selected at XDCR
CONNECT on the DRAFT SETTING
menu.
ZOOM MODE (BOTTOM LOCK, BOTTOM ZOOM, MARKER ZOOM,
DISCRIM-1/2, DISCRIM-1/3)
USER-2
SCREEN LAYOUT (Same as USER-1, default setting:
)
DISP MODE (Same as USER-1, default setting:[LF]Zm/Nor+[HF]Zm/Nor)
ZOOM MODE (Same as USER-1, default setting:BOTTOM ZOOM)
EXT DEVICE (ETR, TS/OTHER)
DEFAULT SET (NO, YES)
SYSTEM
2
(Continued on the next page)
AP-3
(Continued from the previous page)
SYSTEM SETTING
LANGUAGE (ENGLISH, JAPANESE)
PICT ADV DIR (LEFT, RIGHT, L/R)
DEPTH SCALE (RIGHT, CENTER, OFF)
DISP DIVISION (
)
ZOOM MARKER (OFF, ON)
FREE SHIFT (OFF, ON)
ECHO STRETCH (ON, OFF)
DEPTH UNIT (m, ft, fa, hiro, P/B)
SPEED UNIT (kt, km/h, sm/h)
TEMP UNIT ( C, F)
BOTTOM LEVEL (-40-+0, +0)
ES/DRAFT SETTING
XDCR CONNECT (INTERNAL, ETR, TS/OTHER)
TX POWER (MAX, 1/2, 1/4, 1/8, 1/16, MIN)
DRAFT (-15ft-+90ft; +0ft)
FREQ CHOICE (XXX kHz)
HF and LF should be set.
*:FCV-1200L only
E/S SIG OUT (OFF, LF, HF, LF/HF)
KP SETTING (INTERNAL, EXTERNAL)
RANGE SETTING
RANGE1 (16-6000ft, 30ft)
RANGE2 (16-6000ft, 60ft)
RANGE3 (16-6000ft, 120ft)
RANGE4 (16-6000ft, 250ft)
RANGE5 (16-6000ft, 500ft)
RANGE6 (16-6000ft, 1000ft)
RANGE7 (16-6000ft, 1600ft)
RANGE8 (16-6000ft, 3000ft)
M/Z RANGE (16-600ft, 16ft)
B/L RANGE (16-600ft, 16ft)
SPLIT RANGE (OFF, ON)
TEMP SETTING
TEMP INPUT (SONDE, SENSOR, NMEA, CIF)
TEMP ADJUST (-20.0 F-+20.0 F, +0.0 F)
TEMP READOUT (OFF, ON)
TEMP GRAPH (OFF, NARROW, STD, EXPAND)
TEMP COLOR (STD, WHITE, RED, BLACK, YELLOW)
(Continued on the next page)
AP-4
(Continued from the previous page)
NET SONDE SETTING
SONDE MARK (OFF, LF, HF)
COLOR (1, 2, 3)
WIDTH (2dots, 3dots, 4dots, 5dots)
SONDE GRAPH (OFF, ON)
GRAPH MODE (SURFACE, BOTTOM)
GRAPH WIDTH (1/4, 1/2)
GRAPH RESET (NO, YES)
USER COLOR SETTING
COLOR NO. (BKGD, ECHO1-ECHO15)
RED (0-15, 0)
GREEN (0-15, 2)
BLUE (0-15, 9)
DEFAULT SET (NO, YES)
USER CLUTTER SETTING
COLOR-7 (1-14, 3)
COLOR-6 (1-14, 3)
COLOR-5 (1-14, 3)
COLOR-4 (1-14, 3)
COLOR-3 (1-14, 3)
COLOR-2 (1-14, 3)
COLOR-1 (1-14, 3)
BACKGROUND (1-14, 3)
DEFAULT SET (NO, YES)
NAV DATA SETTING
SPEED INFO (OFF, ON)
NMEA VERSION (Ver1.5, Ver2.0, SPECIAL)
NAV DATA (LC, LA, DECCA, GPS, DR, AUTO)
COURSE (TRUE, MAG)
TLL OUTPUT (OFF, ON)
TARGET ECHO
TARGET ECHO (NORMAL, SURFACE, SQUID, DEEP SEA)
TEST MODE
DIAGNOSTICS (NO, YES)
TEST PATTERN (NO, YES)
DEFAULT SETTING
DEFAULT SET (NO, YES)
AP-5
APPENDIX 2
SCREEN DIVISION
The screen divisions are arranged as below through the SCREEN LAYOUT on the USER-1/2
menu.
(full screen)
HIGH
NORMAL
LOW
NORMAL
ETR/
TELESOUNDER
NORMAL
HIGH
ZOOM
[HF]: Normal
[LF]: Normal
*[Ex]: Normal
[HF]: Zoom
LOW
ZOOM
ETR/
TELESOUNDER
ZOOM
MIX
NORMAL
[LF]: Zoom
*[Ex]: Zoom
[Mix]: Normal
*: For FCV-1200L with EXIF assy. (option). Select INTERNAL at HF/LF XDCR CONNECT on
ES/DRAFT SETTING menu.
AP-6
(two split screen)
(1:2)
(half)
H
Z
O
O
M
H
HIGH
NORMAL
N
O
R
M
A
L
HIGH
ZOOM
L
Z
O
O
M
[HF]: Zm/Nor
E T
T / S
R
Z
O
O
M
E T
T / S
R
N
O
R
M
A
L
L
ETR/
TELESOUNDER
NORMAL
ETR/
TELESOUNDER
ZOOM
L
H
N
O
R
M
A
L
N
O
R
M
A
L
N
O
R
M
A
L
N
O
R
M
A
L
E T
T / S
R
ETR/
TELESOUNDER
NORMAL
N
O
R
M
A
L
Z
O
O
M
HIGH
ZOOM
H
Z
O
O
M
LOW
ZOOM
H
N
O
R
M
A
L
[LF]:Zm+[HF]:Zm
L
N
O
R
M
A
L
M
I
X
N
O
R
MIX
NORMAL
LOW
NORMAL
[LF]+[Mix]
L
L
S
U
B
N
O
R
M
A
L
LOW
NORMAL
L
N
O
R
M
A
L
LOW
NORMAL
ETR/
TELESOUNDER
NORMAL
*[Ex]+[LF]
*[Ex]+[HF]
L
HIGH
NORMAL
[LF]+[HF]
HIGH
NORMAL
H
LOW
ZOOM
[LF]: Zm/Nor
*[Ex]: Zm/Nor
E T
T / S
R
LOW
NORMAL
N
O
R
M
A
L
M
I
X
MIX
NORMAL
N
O
R
HIGH
NORMAL
[HF]+[Mix]
H
H
S
U
B
N
O
R
M
A
L
HIGH
NORMAL
HIGH
SUB
[H]sub+[HF]
LOW
NORMAL
Tbe dashed line shows position of
dividing line for vertical (1:2) split screen.
LOW
SUB
[L]sub+[LF]
*: For FCV-1200L with EXIF assy. (option). Select INTERNAL at HF/LF XDCR CONNECT on
ES/DRAFT SETTING menu.
AP-7
(three split screen)
L
N
O
R
M
A
L
H
H
N
O
R
M
A
L
Z
O
O
M
HIGH
NORMAL
L
L
H
HIGH
ZOOM
Z
O
O
M
N
O
R
M
A
L
N
O
R
M
A
L
LOW
NORMAL
N
O
R
M
A
L
H
H
N
O
R
M
A
L
Z
O
O
M
HIGH
NORMAL
HIGH
ZOOM
ETR/
TELESOUNDER
NORMAL
E T
T/S
R
N
O
R
M
A
L
L
L
Z
O
O
M
N
O
R
M
A
L
H
N
O
R
M
A
L
N
O
R
M
A
L
L
H
N
O
R
M
A
L
N
O
R
M
A
L
HIGH
NORMAL
ETR/
TELESOUNDER
NORMAL
ETR/
TELESOUNDER
ZOOM
E T E T
T/S T/S
R
R
Z
O
O
M
N
O
R
M
A
L
N
O
R
M
A
L
H
H
N
O
R
M
A
L
S
U
B
LOW
NORMAL
LOW
ZOOM
ETR/
TELESOUNDER
NORMAL
L
N
O
R
M
A
L
LOW
NORMAL
ETR/
TELESOUNDER
NORMAL
ETR/
TELESOUNDER
ZOOM
*[EX]:Zm/Nor+[LF]
HIGH
NORMAL
LOW
NORMAL
ETR/
TELESOUNDER
NORMAL
L
H
N
O
R
M
A
L
N
O
R
M
A
L
M
I
X
N
O
R
*[Ex]+[LF]+[HF]
L
LOW
ZOOM
*[Ex]+[LF]: Zm/Nor
*[EX]:Zm/Nor+[HF]
E T
T/S
R
N
O
R
M
A
L
Z
O
O
M
*[Ex]+[HF]: Zm/Nor
E T E T
T/S T/S
R
R
LOW
NORMAL
[LF]: Zm/Nor+[HF]
[LF]+[HF]: Zm/Nor
E T
T/S
R
HIGH
NORMAL
MIX
NORMAL
HIGH
NORMAL
LOW
NORMAL
[LF]+[HF]+[Mix]
HIGH
NORMAL
HIGH
SUB
LOW
NORMAL
L
S
U
B
L
H
N
O
R
M
A
L
N
O
R
M
A
L
[LF]+[H]sub+[HF]
HIGH
NORMAL
LOW
NORMAL
LOW
SUB
[L]sub+[LF]+[HF]
*: For FCV-1200L with EXIF assy. (option). Select INTERNAL at HF/LF XDCR CONNECT on
ES/DRAFT SETTING menu.
(four split screen)
LOW
NOR
HIGH
NOR
LOW
ZOOM
HIGH
ZOOM
[LF]: Zm/Nor+[HF]: Zm/Nor
AP-8
APPENDIX 3
DISPLAY DIVISION
The display is arranged as shown below through DISP DIVISION on the SYSTEM SETTING
menu.
LF or HF
NORMAL
SONDE
WATER
TEMP
"ON"
DUAL
LOW/HIGH
S
O
N
D
E
LOW
S
O
N
D
E
LOW/
HIGH
HIGH
LOW HIGH
LOW/HIGH
S
C
O
P
E
ZOOM
S
O
N
D
E
A
A
A-SCOPE
"ON"
ZOOM
LOW HIGH
S
C
O
P
E
Z
O
O
M
LOW/
HIGH
H
I
G
H
/
L
O
W
Z
O
O
M
H
I
G
H
/
L
O
W
A
S
C
O
P
E
The width of the sonde temperature display may be set to 1/4 or 1/2 the screen size. Selection
is made with SONDE GRAPH in the NET SONDE SETTING menu. When Sonde temperature
display is set to 1/2, and the A-scope is turned on, the width of the sonde temperature display
becomes 1/4 automatically.
AP-9
SPECIFICATIONS OF THE COLOR LCD VIDEO SOUNDER
FCV-1200L/1200LM
1. ECHO SOUNDER (FCV-1200L ONLY)
(1) TX Frequency
15/28/38/45/50/68/88/107/150/200/400 kHz, select 2 channels
400 kHz requires optional transmit board
(2) Output Power
1, 2 or 3 kWrms
(3) TX Rate
5 to 1000 pulse/min (20 to 1000 m range, normal mode)
Max. 2400 pulse/min (5 m range, surface mode)
(4) Pulselength
0.2 to 5.0 msec
2. DISPLAY UNIT
(1) Display Mode
10.4 inch TFT color LCD, VGA: 640 x 480 pixels, Portrait/Landscape
(2) Echo Color
8 or 16 colors according to echo intensity.
(3) Background Color
Selectable among 5 colors.
(4) Display Mode
Single mode (high/low frequency), Dual-frequency, Zoom, Mix, A-scope
(5) Zoom Display
Marker zoom, Bottom zoom, Bottom-lock expansion
(6) Range Shift
Range: 5-2000 m, Shift: 0-2000 m, Expansion range: 5-200 m
(7) Display Advance Speed
7 steps (Lines/TX: Freeze, 1/16, 1/8, 1/4, 1/2, 1/1, 2/1, 3/1, 4/1)
(8) Alarm
Fish alarm, Water temperature alarm, Bottom alarm
(9) Noise Limiter
Frequency adjustable range: ±10% (-4.5 to +10% for 68/200 kHz)
(10)
Other Features Automatic bottom tracking, Clutter rejector,
Water temperature graph (optional sensor required)
3. INTERFACE
(1) Data Format
IEC 61162-1, NMEA0183 Ver.1.5/2.0
(2) Input Data
GGA, GLC, GLL, GTD, MTW, RMA, RMB, RMC, VTG
Any talker is available
(3) Output Data
SDDBS, SDDBT, SDDPT, SDTLL, YCMTW*, VRM
*: Optional sensor required
(4) Output for Monitor
RGB: VGA signal, optional interface IF-8000 required
4. POWER SUPPLY
(1) Voltage and Current
12-24 VDC: 10.0-5.0 A
(2) Power Consumption
120 VA or less
(3) Rectifier
100/110/115/200/220/230 VAC available (option)
SP - 1
5. ENVIRONMENTAL CONDITION
(1) Temperature
-15 °C to +55 °C
(2) Relative Humidity
Less than 95% (at 40°C)
(3) Water Resistance
Display Unit and Control Unit: IEC IPX5
Processor Unit: IEC IPX2
6. COATING COLOR
(1) Processor Unit
2.5GY5/1.5
(2) Display Unit and Control Unit
Panel: N3.0 Sleektone No.535, Chassis: 2.5GY5/1.5
SP - 2
INDEX
A
I
advance speed ........................................ 1-19
interference............................................1-22
Aerated water .......................................... 4-5
A-scope display ...................................... 1-21
B
background color ...................................... 2-3
basic range............................................. 1-11
BOTTOM ALARM .................................... 2-6
BOTTOM LOCK ...................................... 1-6
Bottom nature.......................................... 4-3
Bottom profile .......................................... 4-2
BOTTOM ZOOM ...................................... 1-6
BRILL key ............................................... 1-3
BTM-FISH ALARM .................................. 2-6
C
clutter ................................................... 1-15
Current rip .............................................. 4-4
D
DEPTH UNIT .......................................... 3-3
discrimination.......................................... 1-6
DISPLAY DATA ....................................... 2-5
L
language ..................................................3-2
M
marker Line ...........................................1-14
MARKER ZOOM ......................................1-6
MARKER/TLL key..................................1-14
mix ......................................................... 1 - 9
MODE switch...........................................1-4
N
navigation data ......................................3-16
NMEA ...................................................3-16
P
Panel test.................................................5-5
Plankton ..................................................4-4
R
RANGE switch ....................................... 1-11
S
DRAFT .................................................... 3-5
screen division........................................ 2-11
dual......................................................... 1-5
shift .......................................................1-12
F
False image.............................................. 4-5
FISH ALARM .......................................... 2-6
Fish quantity ........................................... 4-3
Fish school size ........................................ 4-3
G
GAIN control.......................................... 1-13
H
HUE........................................................ 2-3
signal level.............................................1-18
single picture............................................1-4
smoothing ................................................2-5
SPEED UNIT...........................................3-3
sub gain .................................................2-12
Surface noise............................................4-5
T
TEMP ALARM .........................................2-6
TEMP UNIT.............................................3-3
temperature graph....................................3-9
IN-1
LF or HF
NORMAL
SONDE
WATER
TEMP
"ON"
ZOOM
HIGH
LOW/HIGH
LOW
ZOOM
LOW/HIGH
S
O
N
D
E
S
O
N
D
E
LOW/
HIGH
A
A-SCOPE
"ON"
DUAL
LOW/
HIGH
S
C
O
P
E
HIGH
S
O
N
D
E
LOW
HIGH
LOW
A
S
C
O
P
E
LOW/
HIGH
ZOOM
LOW/
HIGH
ZOOM
A
S
C
O
P
E
The width of the sonde temperature display may be set to 1/4 or 1/2 the screen size. Selection
is made with SONDE GRAPH in the NET SONDE SETTING menu. When Sonde temperature
display is set to 1/2, and the A-scope is turned on, the width of the sonde temperature display
becomes 1/4 automatically.
AP-10
TVG ...................................................... 1-16
W
U
white line.................................................2-3
USER-1,2................................................. 1-9
V
VRM...................................................... 1-13
IN-2
WHITE MARKER ....................................2-4