Furuno Fcv620 Fish Finder User Manual

FI-504 MULTI
Instrument
www.furuno.co.jp
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
Telephone : +81-(0)798-65-2111
Fax
: +81-(0)798-65-4200
All rights reserved.
Printed in Japan
A : OCT . 2007
A1 : OCT . 17, 2007
Pub. No. OME-72690-A1
(DAMI )
FI-504
*00016733410*
*00016733410*
* 0 0 0 1 6 7 3 3 4 1 0 *
IMPORTANT NOTICES
• The descriptions in this manual are intended for readers with a solid knowledge
of English.
• No part of this manual may be copied or reproduced without written permission.
• If this manual is lost or worn, contact your dealer about replacement.
• The contents of this manual and equipment specifications are subject to change
without notice.
• The example screens (or illustrations) shown in this manual may not match the
screens you see on your display. The screen you see depends on your system
configuration and equipment settings.
• Store this manual in a convenient place for future reference.
• FURUNO will assume no responsibility for the damage caused by improper use
or modification of the equipment (including software) by an unauthorized agent
or a third party.
• When it is time to discard this product it must be done according to local regulations for disposal of industrial waste. For disposal in the USA, refer to the Electronics Industries Alliance (http://www.eiae.org/).
i
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
The operator of this equipment must read these safety instructions before attempting to
operate the equipment.
WARNING
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Warning, Caution
Mandatory Action
Prohibitive Action
Safety instructions for the operator
Safety instructions for the installer
WARNING
Do not open the equipment.
Only qualified personnel should
work inside the equipment.
Do not disassemble or modify
the equipment.
Fire or electrical shock can result if
the equipment is modified.
Do not operate the equipment
with wet hands.
Electrical shock can result.
Make sure no rain or water
splash leaks into the equipment.
WARNING
Turn off the power at the switchboard before beginning the
installation.
Turn off the power to prevent
electrical shock.
Make sure the installation site is
not subject to water spray.
Fire or electrical shock can result if
water leaks into the equipment.
CAUTION
Observe the following compass
safe distances to prevent interference to the instruments:
Fire or electrical shock can result
if water leaks into the equipment.
Immediately turn off the power
at the switchboard if water leaks
into the equipment.
Continued use of the equipment
can cause fire or electrical shock.
Warning Label
A warning label is attached to the equipment. Do not
remove the label. If the label is missing or damaged,
contact a FURUNO agent or dealer about replacement.
ii
Standard Steering
compass compass
FI-50 series
Instruments
0.35 m
0.30 m
TABLE OF CONTENTS
FOREWORD .............................................................................................. iv
SYSTEM CONFIGURATION ....................................................................... v
1.OPERATION ............................................................................................. 1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Operating Controls, Display Layout...................................................................... 1
Turning the Power On/Off .................................................................................... 2
Adjusting Brilliance and Contrast ......................................................................... 2
Selecting a Display............................................................................................... 3
Selecting Apparent or True Wind Angle, Wind Speed.......................................... 8
Resetting Counters and Indications ..................................................................... 8
Alarms .................................................................................................................. 9
Timers ................................................................................................................ 11
2. MAINTENANCE, TROUBLESHOOTING .............................................. 13
2.1 Preventive Maintenance..................................................................................... 13
2.2 Troubleshooting.................................................................................................. 14
3. INSTALLATION ..................................................................................... 15
3.1
3.2
3.3
3.4
Equipment Lists.................................................................................................. 15
Mounting............................................................................................................. 16
Wiring ................................................................................................................. 18
Setting Up........................................................................................................... 21
SPECIFICATIONS ................................................................................. SP-1
PACKING LIST ........................................................................................ A-1
OUTLINE DRAWINGS............................................................................. D-1
INTERCONNECTION DIAGRAM ............................................................ S-1
iii
FOREWORD
FOREWORD
A Word to the Owner of the FI-504
Congratulations on your choice of the FURUNO FI-504 Multi Display, a
member of the FI-50 series of marine instruments. We are confident you
will see why the FURUNO name has become synonymous with quality
and reliability.
For over 50 years FURUNO Electric Company has enjoyed an enviable
reputation for quality marine electronics equipment. This dedication to
excellence is furthered by our extensive global network of agents and
dealers.
This equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its
intended function unless operated and maintained properly. Please carefully read and follow the recommended procedures for operation and
maintenance.
Thank you for considering and purchasing FURUNO equipment.
Features
The FI-504 Multi Display provides heading, environment, autopilot, engine, depth, speed, and wind information, all on a high quality, backlit
LCD. The sturdy weather-proof case is built to stand up to even the
harshest of environments.
The main features are
• Eight varieties of displays: heading, environment, autopilot, engine,
depth, speed, timer, and wind.
• Four levels of backlighting including off.
• Timers: Stopwatch and count-down
• Depth alarms: Shallow alarm, Deep alarm
• Anchor alarms: Shallow alarm, Deep alarm
• Voltage alarm monitors power source voltage
• Wind alarms: High apparent wind angle, Low apparent wind angle,
Max. true wind speed, Low true wind speed
• Speed indications: Max. STW, Average STW, SOG, Max. SOG, Average SOG, Wind speed, Max. true wind speed
• Log indication from 0 to 99,999 nm
• Resettable trip counter, from 0 to 999 nm
iv
SYSTEM CONFIGURATION
Standalone configuration
NMEA 2000 Sensor
(ex. Smart Sensor)
: Standard Supply
: Optional Supply
: Local Supply
12 VDC
NOTICE: Turn on the terminal resistor in the instrument when connecting
an NMEA 2000 sensor. For the procedure, see the section on setting up,
in the installation chapter.
v
SYSTEM CONFIGURATION
NMEA 2000 network
FI-5001
WIND
TRANSDUCER
TERMINAL BOX
(where necessary)
FI-504
MULTI
FI-501*
and/or
FI-502
FI-505
COURSE PILOT
FI-506
RUDDER
FI-503
DIGITAL
30
NMEA 2000
SENSOR*
NMEA 2000
SENSOR*
NMEA 2000
SENSOR*
NMEA 2000
SENSOR*
NMEA 2000
SENSOR*
JUNCTION BOX
FI-5002
* NMEA 2000 SENSORS
- Boat speed
- Depth
- Heading
- Navigation
- Environment
- Autopilot
- Engine
*FI-501 Wind Angle
FI-502 Close Hauled Wind Angle
12 VDC
(not necessary if powered
by NMEA 2000 network)
: Standard Supply
: Optional Supply
: Local Supply
NOTICE: Turn on the terminal resistor in the terminator of the NMEA
2000 network.
vi
1.
OPERATION
Provided applicable sensors are connected, the FI-504 provides the following information, all on a backlit LCD:
•
•
•
•
•
•
•
•
•
1.1
Depth
Speed
Heading
Environment data
Autopilot (rudder)
Engine
Wind
Timers
Navigation data
Operating Controls, Display Layout
Mode name
(Ex. SPD=Speed)
SELECT/CLEAR
- Select menu option.
- Silence alarm.
- Clear data.
- Reset counters and indcations.
- Increment value.
APP/TRUE
- Select apparent or true (wind) alternately.
- Decrement value.
MODE
Select a display.
DISP
- Turn on power.
- Select a display category.
1
1. OPERATION
1.2
Turning the Power On/Off
To power the instrument, press the DISP key. All LCD segments go on
and off and then the last-used display appears.
To power off the instrument, press the DISP and MODE keys together
(about 7-10 seconds). The timer appears and counts down from three
seconds to one second, and then the power goes off.
POWER
Press DISP
and MODE
keys together
3
POWER
2
POWER
1
POWER
OFF
Power OFF sequence
1.3
Adjusting Brilliance and Contrast
1. Press the DISP and MODE keys together. The display for adjustment
of brilliance appears, with current brilliance setting flashing.
BRILL
2
Brilliance setting (flashing)
2. Within seven seconds of completing step 1, press the APP/TRUE key
to lower the brilliance, or the SELECT/CLEAR key to raise it.
3. Press the DISP and MODE keys together. The display for adjustment
of contrast appears, with current contrast setting flashing.
CONT
3
Contrast setting (flashing)
4. Within seven seconds of completing step 3, press the APP/TRUE key
to lower the contrast, or the SELECT/CLEAR key to raise it.
5. Press the DISP and MODE keys together to save the settings and
restore normal operation.
The brilliance and contrast will be the same on all units which are synchronized. (For how to synchronize units, see page 26.)
2
1. OPERATION
1.4
Selecting a Display
Use the DISP key to select a display category. Select desired display
with the MODE key.
SPEED
Boat speed
Maximum STW
Average STW
SOG
Maximum SOG
Average SOG
VMG to windward
Log
Trip
DEPTH
Current depth
Shallow alarm
Deep alarm
Shallow anchor alarm
Deep anchor alarm
TIMER
Count-up timer
Count-down timer 1
Count-down timer 2
ENGINE
Trip fuel usage
Fuel usage rate
Engine RPM
WIND
DISP
AUTOPILOT
Rudder angle
Wind speed
Maximum true wind speed
Maximum true wind speed alarm
Low true wind speed alarm
Wind angle
High apparent wind angle alarm
Low apparent wind angle alarm
Beaufort wind speed
Ground wind direction
HEADING
Current heading
Average heading
Heading on next tack
Course over ground
Course made good
Distance made good
ENVIRONMENT
Battery voltage
Minimum battery voltage alarm
Time
Date
Water temperature
Air temperature
Air pressure
Humidity
Wind chill temperature
Dew point
NAVIGATION
Bearing to waypoint
Distance to waypoint
Cross track error
Waypoint number/name
Latitude
Longitude
Course over ground
Speed over ground
Satellites tracked
Roll
Pitch
3
1. OPERATION
1.4.1
Display description
Depth category
Display title
Current depth
Shallow alarm
Indication
DPTH
SHALLOW
Deep alarm
DEEP
Shallow anchor
alarm
SHALLOW
Deep anchor
alarm
DEEP
Function
Current depth, in meters, feet or fathoms.
Set shallow depth alarm. Audio and visual
alarms are released when the depth is
lower than the threshold value.
Set deep depth alarm. Audio and visual
alarms are released when the depth is
higher than the threshold value.
Set shallow anchor alarm. Audio and visual
alarms are released when the depth is
lower than the threshold value.
Set deep anchor alarm. Audio and visual
alarms are released when the depth is
higher than the threshold value.
Speed category
Display title
Boat speed
SPD
Maximum STW
SPD MAX
Average STW
SPG AVG
SOG
SOG
Maximum SOG
SOG MAX
Average SOG
SOG AVG
VMG to windward
VMG
Log
LOG
Trip
TRIP
4
Indication
Function
Boat speed, in knots (kt), miles per hour
(MPH) or kilometers per hour (KMH).
Maximum boat speed, in knots (kt), miles
per hour (MPH) or kilometers per hour
(KMH).
Average boat speed, in knots (kt), miles per
hour (MPH) or kilometers per hour (KMH).
Speed over ground, in knots (kt), miles per
hour (MPH) or kilometers per hour (KMH).
Maximum speed over ground, in knots (kt),
miles per hour (MPH) or kilometers per
hour (KMH).
Average speed over ground, in knots (kt),
miles per hour (MPH) or kilometers per
hour (KMH).
Velocity made good to windward, in knots
(kt), miles per hour (MPH) or kilometers per
hour (KMH).
Log distance (total distance run), in nautical
miles, (NM) kilometers (KM) or statute
miles (SM).
Trip distance (distance run between two
points), in nautical miles (NM), kilometers
(KM) or statute miles (SM).
1. OPERATION
Timer category
Display title
Indication
Count up timer
UP
Count down timer 1 DOWN 1
Count down timer DOWN 2
Function
Count-up timer.
Count-down timer 1.
Count-down timer 2.
Wind category
Display title
Indication
Wind speed
APP (or TRUE)
Maximum true wind MAX TRUE
speed
Maximum true wind
MAX TRUE
speed alarm
Low true wind
speed alarm
TRUE LO
Wind angle
APP (or TRUE)
High apparent wind
APP HI
angle alarm
Low apparent wind
angle alarm
APP LO
Beaufort wind
speed
BFT
Ground wind angle GWIND
Function
Wind speed, in knots or meters/second.
Maximum true wind speed.
Set maximum true wind speed alarm. Audio
and visual alarms are released when the
wind speed goes higher than the threshold
value.
Set low true wind speed alarm. Audio and
visual alarms are released when the wind
speed goes lower than the threshold value.
Apparent (or true) wind angle, in degrees.
Set high apparent wind angle alarm. Audio
and visual alarms are released when the
wind angle at starboard goes higher than
the threshold value.
Set low apparent wind angle alarm. Audio
and visual alarms are released when the
wind angle at port goes lower than the
threshold value.
Beaufort wind speed. Beaufort speeds up to
12 are shown. See the table below for Beaufort no. and wind speed.
Angle of wind over ground, in degrees.
Bearing reference in Magnetic (MAG) or
True (TRUE).
Beaufort no. and wind speed
Wind speed
Beaufort
no.
kt
m/s
Wind speed
Beaufort
no.
kt
m/s
0
0
0-0.2
7
28-33
14.4-17.4
1
1-3
0.5-2.0
8
34-40
17.5-21.0
2
4-6
2.1-3.5
9
41-47
21.1-24.6
3
7-10
3.6-5.6
10
48-55
24.7-28.8
4
11-16
5.7-8.6
11
56-63
28.9-32.6
5
17-21
8.7-11.2
12
64
32.7-32.9
6
22-27
11.3-14.3
5
1. OPERATION
Heading category
Display title
Current heading
Indication
HDG
Average heading
HDG AVG
Heading on next tack
TACK
Course over ground
Course made good
Distance made good
COG
CMG
DMG
Function
Heading, in degrees. Bearing reference
in Magnetic (MAG) or True (TRUE).
Average heading, in degrees. Bearing
reference in Magnetic (MAG) or True
(TRUE).
Heading on next tack, in degrees true
(fixed). Bearing reference in Magnetic
(MAG) or True (TRUE).
Course over ground, in degrees.
Course made good, in degrees.
Distance made good, in kilometers
(km), nautical miles (nm) or statute
miles (sm).
Navigation category
Display title
Bearing to waypoint
BTW
Distance to waypoint
DTW
Cross track error
XTE
Waypoint number/name
Latitude
Longitude
Course over ground
WPT
LAT
LON
COG
Speed over ground
SOG
Satellites tracked
Roll
Pitch
GPS SAT
ROLL
PITCH
6
Indication
Function
Bearing to waypoint, in degrees.
Bearing reference of Magnetic (MAG) or
True (TRUE)
Distance to waypoint, in kilometers
(KM), nautical miles (NM) or statute
miles (SM).
Cross-track error, in kilometers (KM),
nautical miles (NM) or statute miles
(SM).
Waypoint number and name are shown.
Position in latitude.
Position in longitude.
Course over ground, in degrees.
Bearing reference in Magnetic (MAG) or
True (TRUE).
Speed over ground, in knots (K), miles
per hour (MPH) or kilometers per hour
(KMH).
GPS satellites tracked.
Ship’s roll, in degrees.
Ship’s pitch, in degrees.
1. OPERATION
Environment category
Display title
Battery voltage
Minimum battery voltage
alarm
Indication
VOLTS
VOLTS LO
Time
-
Date
Water temperature
Air temperature
Air pressure
Humidity
Wind chill temperature
WATER
AIR°
HPA
HUMID
CHILL
Dew point
DEW
Function
Battery voltage.
Set low battery voltage alarm.
Audio and visual alarms are
released when the battery
voltage goes lower than the
threshold value.
Current time, in 12-hour or
24-hour format.
Current date.
Water temperature, in °C or °F.
Air temperature, in °C or °F.
Air pressure, in Hectopascal.
Relative humidity, in percentage.
Wind chill temperature, in °C or
°F.
Dew point, in °C or °F.
Autopilot category
Display title
Rudder angle
Indication
RUDDER
Function
Rudder angle, in degrees either
P(ort) or S(tarboard).
Engine category
Display title
Trip fuel used
TOTAL
Indication
Fuel rate
RTE (L/H)
Engine RPM
RPM
Function
Total fuel consumption, in liters
or gallons.
Amount of fuel consumed in
hour, in liters/hour (L/H) or
gallons/hour (G/H).
Engine speed per minute.
Note: In case of multiple engines, the data of desired engine number
(max. eight, E0-E7) can be selected with the SELECT/CLEAR key.
Scrolling speed and scrolling direction
Display scrolling speed and direction can be changed by the length of
key push.
Short push: Scroll in forward order.
Medium push: Go back one display. Several beeps sound and then the
previous display appears.
Hold down: Rapid scrolling, in forward direction. Several beeps sound
and then speed is changed.
7
1. OPERATION
1.5
Selecting Apparent or True Wind Angle,
Wind Speed
You can show wind angle and wind speed in apparent or true wind. The
apparent wind is the actual flow of air acting upon a sail, or the wind as
it appears to the sailor. True wind is the wind seen by a stationary observer in velocity and direction.
WIth a wind angle or wind speed indication displayed, press the APP/
TRUE key to change the wind angle or wind speed to apparent and true
alternately. A beep sounds after the change is completed. (Wind angle
and wind speed displays are mutually changed.) True wind requires boat
speed input. If there is no speed input three dashes appear.
APP
KT
5.0
HI
APP
TRUE
TRUE
135
HI
APP
TRUE
KT
HI
9.6
Apparent and true
wind speeds
1.6
APP
TRUE
157
HI
Apparent and true
wind angles
Resetting Counters and Indications
You can reset the following counters and indications:
•
•
•
•
•
•
•
•
•
Trip distance
Course made good
Distance made good
Average speed
Average SOG
Maximum speed
Maximum SOG
Average heading
Maximum true wind speed
Select the applicable display and press and hold down the SELECT/
CLEAR key. A short beep sounds, the counter or indication flashes twice
and then a long beep sounds to indicate that resetting is completed.
8
1. OPERATION
1.7
Alarms
There nine conditions which trigger audio and visual alarms: Shallow
alarm, Deep alarm, Shallow anchor alarm, Deep anchor alarm, Max. true
wind speed alarm, Low true wind speed alarm, High apparent wind angle
alarm, low apparent wind angle alarm, and low battery voltage alarm.
1. Use the DISP and MODE keys to select desired alarm page, referring
to the illustration below for alarm location.
Display
category
Available alarms
DEPTH
DEEP
SHALLOW
020
Shallow alarm
WIND
TRUE
MAX
KT
ENVIRONMENT
5.0
Deep alarm
Shallow anchor
alarm
LO
38.9
10.0
150
TRUE
KT
APP S* HI
9.7
Max. true wind
speed alarm
DEEP
SHALLOW
Low true wind
speed alarm
Deep anchor
alarm
APP S* LO
12.2
5.4
High apparent
wind angle alarm
Low apparent
wind angle alarm
VOLTS
LO
9.0
Low voltage
alarm
*S (Starboard) or P (Port)
.
Alarm description
Alarm
Shallow alarm
Deep alarm
Shallow anchor alarm
Deep anchor alarm
Max. true wind speed
alarm
Low true wind speed
alarm
High apparent wind
angle alarm
Low apparent wind
angle alarm
Alarms released when;
depth is shallower than this
threshold.
depth is deeper than this
threshold.
anchor depth is shallower than
this threshold.
anchor depth is greater than
this threshold.
max. true wind speed is
greater than this threshold.
true wind speed is lower than
this threshold.
apparent wind angle is higher
than this threshold.
apparent wind angle is lower
than this threshold.
Setting range
0.0-303 m
0.1-304 mt
depth is shallower than this
threshold.
depth is deeper than this
threshold.
0.1-999 kts
0-998 kts
0°-179°
S180°-P1°
(S=Starboard, P=Port)
9
1. OPERATION
Alarm description
Alarm
Low battery voltage
alarm
Alarms released when;
battery voltage is lower than
this threshold.
Setting range
5.0 - 20.0 volts
2. If the selected alarm page shows “Off,” press and hold down the
SELECT/CLEAR key until an alarm setting appears.
3. Press the APP/TRUE and SELECT/CLEAR keys together to enable
adjustment. The alarm setting starts flashing.
4. Press the APP/TRUE key to lower the setting; the SELECT/CLEAR
key to raise it.
Note: A low alarm cannot be set higher than its affiliated high (max.)
alarm.
5. Press the APP/TRUE and SELECT/CLEAR keys together to confirm
setting and restore normal operation.
When an alarm is violated, the buzzer sounds and the alarm icon (
)
flashes. You can silence the buzzer with the SELECT/CLEAR key. The
icon continues flashing until the offending alarm is disabled.
While the icon is flashing you can switch between alarm display and current display alternately by pressing the DISP and SELECT/CLEAR keys
together.
10
1. OPERATION
1.8
Timers
Three timers are provided:
• Count-up timer (stopwatch)
• Count-down timer (two provided)
Time is displayed in seconds or minutes, depending on counter values.
Once you have set a timer, you can leave that page and select any other
display. The counter continues to run in the background.
Count-up timer
The count-up timer functions like a stop watch, counting time upward, to
99 hours, 99 minutes and 59 seconds.
Count-down timers
The two count-down timers count down from a time between 15 minutes
and one minute. When these timers have counted down to zero, they
then start counting up. The timers beep at preset intervals to alert you to
specific points in time.
•
•
•
•
Two beeps every minute
Three beeps at the start of the last 30 seconds
One beep/second for each of the last 10 seconds
Two-second beep at zero
How to set the timers
1. Press the MODE key to show the desired timer display.
00:00:00.0
UP
Count-up
timer
DOWN 1
15.0
Count-down
timer 1
DOWN 2
15.0
Count-down
timer 2
2. Do one of the following depending on timer type selected:
Count-up timer:
Press the SELECT/CLEAR key to start the timer. A long beep sounds
and the timer starts counting upward.
Count-down timer:
To start the timer from the time shown, press the SELECT/CLEAR
key. To set a different start time, press the APP/TRUE and SELECT/
CLEAR keys together to enable adjustment. Use the APP/TRUE key
to lower the value; SELECT/CLEAR key to raise it. Press the APP/
TRUE and SELECT/CLEAR keys together to confirm setting. Press
the SELECT/CLEAR key to start the timer.
11
1. OPERATION
To stop or restart the timer, press the SELECT/CLEAR key momentarily. A short beep sounds when the timer is stopped or restarted.
To stop and reset the timer to start value, press the SELECT/CLEAR
key until you hear a long beep. The timer is stopped and reset to start
value.
The timer settings are reflected on any timer-equipped instrument in the
network which is set up for synchronization.
12
2.
MAINTENANCE,
TROUBLESHOOTING
This chapter provides the information necessary for keeping your equipment in good working order.
WARNING
Do not open the equipment.
Only qualified personnel should
work inside the equipment.
2.1
Preventive Maintenance
Following the recommended procedures below will help maintain performance.
Check item
Check point
Remedy
Cabling
Check that all cabling is
Reconnect if necessary. Replace if damaged.
securely fastened and is
free or rust and corrosion.
Cabinet
Dust on cabinet
Remove dust with a soft, lint-free cloth.
NOTICE
Do not apply paint, anti-corrosive
sealant or contact spray to coating
or plastic parts of the equipment.
Those items contain organic solvents
that can damage coating and plastic
parts, especially plastic connectors.
13
2. MAINTENANCE, TROUBLESHOOTING
2.2
Troubleshooting
If you feel the equipment is not functioning properly, follow the procedures in the table below to try to restore normal operation. If normal operation cannot be restored, do not attempt to check inside the cabinet.
There are no user-serviceable parts inside.
Troubleshooting
Problem
Possible cause
Display is
• Power supply
blank. Panel is • Cabling disconnected or
not lit.
damaged.
Power is on but
no or some
data.
Inaccurate data
• Check power supply.
• Check cabling.
Sensor is turned off.
• Turn on sensor.
Cable from sensor is disconnected • Check cabling.
or damaged.
• Electromagnetic field generating • Turn off all electromagnetic field
generating equipment. Turn them on
equipment is in operation.
and off one by one. Check the display. Relocate offending equipment
or this instrument as appropriate.
•
• Cabling from sensor is damaged. Check cabling.
• Sensor is improperly aligned
(where applicable).
14
Remedy
• Check installation. If installation is
proper, an offset may be applied to
certain data. For details, see section
1.7.
3.
INSTALLATION
NOTICE
Do not apply paint, anti-corrosive
sealant or contact spray to coating
or plastic parts of the equipment.
Those items contain organic solvents
that can damage coating and plastic
parts, especially plastic connectors.
3.1
Equipment Lists
Standard supply
Name
Display Unit
Installation
Materials
Type
FI-504
CP26-00600
Code No.
000-011-744
Qty
1
1 set
Remarks
See packing list at end of
manual for details.
Optional supply
Name
Cable Assy.
Flush Mount Kit
Junction Box
Type
FI-50-DROP
FI-50-CHAIN-0.3M
FI-50-CHAIN-5M
FI-50-CHAIN-1M
FI-50-CHAIN-10M
FI-50-CHAIN-20M
FI-50-FLUSH-KIT
FI-5002
Code No.
000-166-945-10
000-166-949-10
000-166-951-10
000-166-950-10
000-166-952-10
000-166-953-10
000-010-619
000-010-765
Qty
1
1
1
1
1
1
1 set
1 set
Remarks
15
3. INSTALLATION
3.2
Mounting
The display unit can be installed two ways: surface mount (fixed at front
panel or fixed from rear panel) and flush mount (optional kit required).
This section covers surface mounting. For flush mounting, see the flush
mounting instructions, issued separately.
Surface mount 1: Fix instrument from front panel
1. Using the template at the back of this manual, open a mounting hole
in the installation site.
2. Detach the front panel together with the keypad assy. Attach sponge
(supplied) to rear of display unit.
3. Set the display unit to the mounting hole, and fix it with four self-tapping screws (3×20, supplied).
4. Attach the front panel and keypad assy. to the display unit.
Keypad Assy.
Sponge
Mounting
Hole
Front Panel
16
Self-tapping screw (3x20)
3. INSTALLATION
Surface mount 2: Fix instrument from rear panel
1. Using the template at the back of this manual, open a mounting hole
in the installation site.
2. Insert studs (M3×40, 2 pcs., supplied) in the holes shown below. (Use
only the studs supplied.)
Insert stud here.
3. Set the display unit to the mounting hole, inserting studs through
respective holes. Fix the display unit with wing nuts (M3, supplied).
Mounting
Hole
Stud (M3x40)
Wing Nut (M3)
17
3. INSTALLATION
3.3
Wiring
3.3.1
Standalone configuration
For standalone configuration the junction box is not necessary; connect
the instrument directly to the power supply.
–
Black
NMEA 2000
drop cable
NMEA 2000
SENSOR
+
Red
12 VDC
FI-50-DROP
Cable (6 m)
Display Unit
FI-504
.
3.3.2
Multi-instrument configuration
FI-50-CHAIN
(0.3 m: Std, 1/5/10/20 m: Option)
DISP. UNIT
FI-501/502/FI-503/FI-505/FI-506
DISP. UNIT
(Instruments can be connected
FI-504
in any order.)
Instruments chained
as above
Instruments chained
as above
FI-5002
POWER CABLE (2 m)
Black
–
+
Red
Instruments chained as above
Instruments chained as above
Instruments chained as above
FI-50-DROP Cable
(6 m, standard supply)
JUNCTION BOX
FI-5002
(optional supply)
NMEA 2000
Backbone Cable
(local supply)
FI-50X FI-50X FI-50X
JUNCTION BOX FI-5002
The total length of drop cables and backbone cables must be within 80 m.
18
3. INSTALLATION
Junction box (option)
The junction box is required when connecting NMEA 2000 network. This
section covers wiring of the junction box. For how to mount the junction
box, see its installation instructions, issued separately.
12VDC
CN3
CN4
DROP DROP
CN5
DROP
BACKBONE
12 VDC
FI-501/502/503/504/505/506
NMEA2000
DEVICE
Fix cable with cable
tie (supplied).
CH3 DROP - CH5 DROP and BACKBONE are socket-and-plug-type terminal blocks. Detach plug to connect wiring to it, by rocking it back and
forth with your fingers. Remove approx. 6 mm of the sheath from the end
of wires and twist wires. Loosen fixing screw in the plug, insert wire into
hole and tighten fixing screw. Set plug to socket.
Drain wire
White
Red
Blue
Black
Sheath
6mm
How to fabricate cable
Fixing screw
Hole for wire
Wire
Twist
How to insert wire
19
3. INSTALLATION
Terminal resistor
The illustration below show various system configurations and what units
to activate the terminal resistor.
Smart sensor+FI-50x
Smart
Sensor
FI-50x
Multiple FI-50 series instruments, FI-5002, drop cabling
FI-50x FI-50x FI-50x FI-50x
Drop cable
FI-5002
Multiple FI-50 series instruments, FI-5002
FI-50x FI-50x FI-50x FI-50x
FI-5002
Multiple FI-50 series instruments, multiple FI-5002
FI-50x FI-50x
FI-50x FI-50x
FI-50x FI-50x
FI-5002
FI-5002
FI-5002
Multiple FI-50 series instruments, FI-5002, smart sensor
Smart
Sensor
FI-50x FI-50x FI-50x
FI-5002
Multiple FI-50 series instruments, FI-5002, heading sensor, smart sensor
Heading
Sensor
(ex. SC-30)
NMEA 2000
Sensor
Smart
Sensor
FI-50x FI-50x
Terminator
Terminator
FI-5002
T-connector
T-connector
T-connector
Multiple FI-50 series instruments, FI-5002, NMEA 2000 sensors
NMEA 2000
Sensor
NMEA 2000
Sensor
FI-50x FI-50x
Terminator
FI-5002
T-connector
= Terminal resistor ON
20
T-connector
3. INSTALLATION
Turn on the terminal resistor in the junction box when the NMEA 2000
sensor(s) connected to it do not have a terminal resistor.
Terminal Resistor
OFF:
ON:
For how to turn on the terminal resistor in a FI-50 series instrument, see
page 33 (FI-501//FI-502/FI-505) or page 35 (FI-506).
3.4
Setting Up
Your instrument is pre-programmed with factory default settings, which
may or may not be suited to your vessel. Therefore, it is necessary to initialize the instrument for use with your vessel. This should be done immediately after completion of the installation.
Two sets of setup menus are provided: setup1 and setup2. The setup1
menu provides system parameters and the setup2 menu has user settings.
3.4.1
Setup1 menu
The setup1 menu contains system parameters which optimize the instrument for use on your vessel. Follow the procedure below to access and
set parameters.
1. Press the APP/TRUE and SELECT/CLEAR keys momentarily to
enable the setup1 menu. The Depth unit selection screen appears,
with the depth unit flashing. (See the illustration on the next page.)
2. Use the DISP key to select a menu item. Each press of the key
changes the menu item in the sequence shown in the illustration on
the next page.
21
3. INSTALLATION
.
DPTH M
DEPTH
Depth unit
SPD
RES
RES
CAL
LOG NM
1.0
TIMER
LOG unit
WIND
CAL
3
SPD
RES
VMG response
S
CAL
0
Speed unit
SOG
HR
12
Time format
RES
CAL
3
3
KT
WINDADJ
CAL
CAL
1.0
F
Audio alarm Wind data selection Wind unit
enable/disable
Wind speed
adjustment
WSPDRES
HDG RES
HDG MAG
CAL
CAL
3
HDGLOCK
CAL
--- ---:--- --CAL
0
Local time
CAL
LOC
Wind angle offset Wind speed Heading reference Heading lock
response
CAL
KT
CAL
Speed response SOG response
WIND
CAL
0 On
TIME
SPD
CAL
Depth offset Shallow alarm lock Depth response
Speed unit resolution Speed offset
ANGLE
DPT
CAL
0.01
VMG
CAL
0.0 Off
SPD --- --- ---
CAL
SHWLOCK
CAL
CAL
TEMP
C
CAL
0
Heading response
W TEMP
CAL
0.0
Water temp. unit Water temp. offset
FUEL
L
CAL
Fuel unit
3. Use the APP/TRUE or SELECT/CLEAR key to set value or select
option.
VMG key: Decrement value
SELECT/CLEAR key: Increment value or select option.
4. To continue, press the DISP key to select another menu item.
5. To save settings and restore normal operation, press the APP/TRUE
and SELECT/CLEAR keys together.
22
3. INSTALLATION
Setup1 menu items
Display
DPTH
M
Function
Select depth unit.
CAL
Set depth offset.
DEPTH
Setting range or
options
M (Meter),
FT (Feet)
Default
setting
M
-99 - +99
0.0
CAL
0.0
SHWLOCK
Lock/unlock shallow alarm setting. ON, OFF
OFF
Set depth response. The lower the 0 - 12
setting the faster the response to
change in depth.
3
CAL
0 OFF
DPT
RES
CAL
F
3
SPD
KT
Select speed unit.
KT (Knot),
KT
MPH (Miles/Hour),
KMH (Kilometers/Hour)
Select speed resolution. Select
number of places to show after
decimal point.
0.01, 0.1
0.01
Set speed adjustment.
0.3 - 2.5
1.0
Select log unit.
NM (Nautical Mile),
SM (Statute Mile),
KM (Kilometer)
NM
CAL
3
SPD
CAL
0.01
SPD --- --- --CAL
1
1.0
LOG NM
CAL
.0
23
3. INSTALLATION
Setup1 menu items
Display
SPD
RES
CAL
0
SOG
RES
CAL
0
0
VMG
RES
CAL
Setting range or
options
Set speed response. The lower the 0 - 12
setting the faster the response to
change in speed.
Default
setting
0
Set SOG response. The lower the 0 - 12
setting the faster the response to
change in speed over ground.
0
Set VMG response. The lower the 0 - 12
setting the faster the response to
change in velocity made good.
3
Enable/disable the timer alarm’s
audio alarm.
ON
Function
3
TIMER
CAL
ON, OFF
3 On
WIND
CAL
n
Select source of wind data. Select F: For FI-5001,
“r” for second unit.
r: repeater
F
Select wind unit.
KT (Knot),
M/S (Meters/Second)
KT
Set wind speed
adjustment.
0.3 - 2.5
1.0
Set wind angle offset.
S 0° - 180°
P 1° - 179°
0
Set wind speed response.
The higher the setting the faster
the response to change in wind
speed.
0 - 12
3
F
WIND
KT
CAL
F
WINDADJ
CAL
1.0
ANGLE
S
CAL
0
WSPDRES
CAL
3
24
3. INSTALLATION
Setup1 menu items
Display
HDG MAG
Function
Select true or magnetic bearing.
CAL
HDGLOCK
CAL
LOC
HDG RES
CAL
0
TIME
HR
Select heading type to display
when
activating locked heading.
Setting range or
options
MAG (Magnetic),
TRU (True
Default
setting
MAG
LOC (Locked),
CUr (Current)
LOC
Set heading response. The lower 0 - 12
the setting the faster the response
to change in heading.
0
Select time format.
12
12, 24 (hour)
CAL
12
--- ---:--- --CAL
2
0
TEMP
C
Use local time. Enter time differ-12 - +12
ence between local time and GMT
to use local time.
0
Select water temperature unit.
°C, °F
°C
Set water temperature
offset.
-99 - +99
0
Select fuel unit.
L (Liter),
G (Gallon)
L
CAL
0
W TEMP
CAL
0.0
FUEL
L
CAL
0
25
3. INSTALLATION
3.4.2
Setup2 menu
The setup 2 menu contains user settings which once preset do not require frequent adjustment.
1. Press and hold down the APP/TRUE and SELECT/CLEAR keys
together (about 5-6 seconds) to enable the user settings menu. The
software version of CPU1 appears. (See the illustration below.)
2. Press the DISP key to choose menu item. Each press of the key
changes the menu item in the sequence shown below.
*XXxx=program and program ver. nos.
XXxxx*
XXxxx*
KEYBEEP
A
CAL
Program ver. Program ver.
no. (CPU1) no. (CPU2)
SETUP
CAL
ON
Setup 1 menu
TIMER
CAL
ON
Timer
displays
A PILOT
CAL
ON
Autopilot
displays
rES
CAL
OFF
Terminal
resistor
WIND
CAL
ON
Wind
displays
ENGINE
CAL
ON
Engine
displays
Auto
brilliance
SYNCHRO
DEPTH
CAL
CAL
Synchronization
HEADING
CAL
ON
Heading
displays
DEMO
CAL
OFF
Demo
mode
CAL
ON
ON
Key
beep
ON
BRILL
ON
Depth
displays
NAVI
CAL
ON
Nav
displays
ALT
CAL
OFF
Alternating
displays
SPEED
CAL
ON
Speed
displays
ENVIRO
CAL
ON
Environment
displays
RESET
CAL
OFF
Restore factory
defaults
3. Use the SELECT/CLEAR key to select setting.
4. To continue, press the DISP key to select another item.
5. To save settings and restore normal operation, press the APP/TRUE
and SELECT/CLEAR keys together.
26
3. INSTALLATION
Setup2 menu items
Display
XXxxx
XXxxx
KEYBEEP
Setting range or
options
Function
Default
setting
Software version of CPU1.
XX=program no. and
xxx=program version no.
-
-
Software version of CPU2.
XX=program no. and
xxx=program version no.
-
-
Turn key beep on/off.
ON, OFF
ON
Auto brilliance on/off.
ON, OFF
ON
CAL
ON
A
BRILL
CAL
ON
ALT
CAL
OFF
SETUP
CAL
OFF
OFF
1: Depth/boat spd
2: Boat spd/water temp.
3: Depth/water temp.
4: Depth/boat spd/water temp.
5: Roll/pitch
6: Latitude/Longitude
Enable/disable access to the ON, OFF
ON
setup1 menu.
Enable/disable alternating
displays.
ON
rES
CAL
Turn the terminal resistor on/ ON, OFF
off.
OFF
Turn on/off synchronization of ON:
FI-50 series instruments.
Synchronize all FI-50
instruments having this
setting.
OFF:
Turn off synchronization.
A:
Synchronize FI-50 instruments having this setting.
b:
Synchronize FI-50 instruments having this setting.
Turn depth displays on/off.
ON, OFF
ON
Turn speed displays on/off.
ON
OFF
SYNCHRO
CAL
ON
DEPTH
ON
CAL
ON
SPEED
ON, OFF
CAL
ON
27
3. INSTALLATION
Setup2 menu items
Display
TIMER
Turn timer displays on/off.
Setting range or
options
ON, OFF
Default
setting
ON
Turn wind displays on/off.
ON, OFF
ON
Turn heading displays on/off. ON, OFF
ON
Turn navigation displays
on/off.
ON, OFF
ON
Turn environmental displays
on/off.
ON, OFF
ON
Turn autopilot displays on/off. ON, OFF
ON
Turn engine displays on/off.
ON, OFF
ON
Demo mode. To enable,
press the SELECT/CLEAR
key. Depth is shown.
To disable and return to this
menu, press and hold down
the SELECT/CLEAR key.
Restore factory defaults.
To restore factory defaults,
press and hold down the
SELECT/CLEAR key to
show ON. Press the key
again. A beep sounds upon
completion.
ON, OFF
OFF
Function
CAL
ON
WIND
CAL
ON
HEADING
CAL
ON
NAVI
CAL
ON
ENVIRO
CAL
ON
A PILOT
CAL
ON
ENGINE
CAL
ON
DEMO
CAL
OFF
RESET
CAL
OFF
28
FI-504 MULTI
SPECIFICATIONS OF
FI-504 MULTI
1
GENERAL
1.1 Display
1.2 Display Content
1.3 I/O Port
2
JUNCTION BOX (OPTION)
2.1 No. of I/O ports
NMEA 2000 Device
NMEA 2000 Backbone
3
12 VDC, less than 0.1 A
12 VDC, less than 1 A, max. 2A connectable
ENVIRONMENTAL CONDITIONS
4.1 Useable Temperature Range
4.2 Relative Humidity
4.3 Waterproofing
Display Unit
Junction Box
4.4 Vibration
5
6 ports
2 ports
POWER SUPPLY AND POWER CONSUMPTION
3.1 Display Unit
3.2 Junction Box
4
Segment LCD
Depth, speed, wind speed, wind angle,
timer, environmental information (water
temperature, air temperature, air
pressure, dewpoint, wind chill
temperature), rudder angle
NMEA 2000, 2 ports
-15°C - +55°C
Less than 95% (+40°C)
IP56
IPX0
- 2 Hz-5 Hz and up to 13.2 Hz with an
excursion of ±1 mm ±10% (7 m/s2
maximum acceleration at 13.2 Hz);
- above 13.2 Hz and up to 100 Hz with a
constant maximum acceleration of 7 m/s2
COATING COLOR
5.1 Display Unit
5.2 Junction Box
N2.5
N2.5
SP-1
E7269S01A
NAME
OUTLINE
INSTALLATION MATERIALS
UNIT
000-167-804-10
M3X40 SUS304
000-167-826-10
M3 SUS304
000-167-453-10
M3 SUS304
000-167-404-10
M3 SUS304
000-163-884-10
3X20 SUS304
000-167-832-10
TZ7583002AO
100-340-471-10
19-028-3124-1
000-011-745-00
FI-504
1
Q'TY
2
2
2
2
4
1
1
CP26-00600
DESCRIPTION/CODE №
FI-504
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
コ-ド番号末尾の[**]は、選択品の代表コードを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
BOLT
寸切ボルト
WING NUT
蝶ナット
FLAT WASHER
ミガキ丸平座金
SPRING WASHER
バネ座金
SELF-TAPPING SCREW
+ナベタッピンネジ 1シュ
SPONGE
サーフェスマウントスポンジ
PANEL REMOVER
パネルリムーバー
工事材料
MONITOR UNIT
表示部
ユニット
PACKING LIST
DOCUMENT
OUTLINE
000-167-332-1*
OM*-72690-*
000-167-295-1*
OS*-72690-*
000-168-501-1*
C72-00705-*
000-166-949-10
FI-50-CHAIN-0.3M
000-166-945-10
FI-50-DROP
**
**
DESCRIPTION/CODE №
1/1
1
1
1
1
1
Q'TY
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF
THE UPPER PRODUCT. QUALITY IS THE SAME.
26AA-X-9860
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
OPERATOR'S MANUAL
取扱説明書
OPERATOR'S GUIDE
INTERNAL RESISTOR
SETTING
操作要領書
内部終端ノ設定
図書
CABLE ASSY.
ケーブル組品0.3M
CABLE ASSY.
ケーブル組品
NAME
26AA-X-9860 -1
A-1
A-2
フラッシュマウントキット
INSTRUMENTS
FLUSH MOUNT KIT.
FI-50
番 号
NO.
名 称
NAME
略 図
OUTLINE
CODE NO.
000-010-619-00
TYPE
FI-50-FLUSH-KIT
型名/規格
DESCRIPTIONS
26AA-X-9401 -3
数量
Q'TY
用途/備考
REMARKS
※1
前面パネルF
1
1/1
TZ7580002A0
FRONT PANEL
1
CODE NO.
000-167-885-10
※1に貼付済み PRE-ATTACHED TO ※1.
FURUNOロゴH3
2
19-028-1502-0
FURUNO STICKER H3
1
CODE NO.
100-339-580-10
ハードカバーF
3
TZ7580007AO
COVER
1
CODE NO.
000-167-887-10
フラッシュマウントツール
4
TZ7580008AO
FRAME
1
CODE NO.
000-167-886-10
+ナベタッピンネジ 1シュ
5
3X20 SUS304
SELF-TAPPING SCREW
4
CODE NO.
000-163-884-10
+ナベPタイトネジ
6
3X12 SUS304
SCREW
4
CODE NO.
000-167-827-10
Fマウントスポンジ
7
TZ7583001AO
SPONGE
1
CODE NO.
000-167-833-10
取付要領書
8
C72-00703-* ワ/エイ
INSTALLATION PROCEDURE
1
CODE NO.
000-167-323-1*
型式/コード番号が2段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。
TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM.
QUALITY IS THE SAME.
THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
FURUNO ELECTRIC CO .,LTD.
26AA-X-9401
Jul.24'07 R.Esumi
D-1
Jul.24'07 R.Esumi
D-2
Jul.24'07 R.Esumi
D-3
C
B
A
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
DROP
SHIELD
NET-S
NET-C
NET-H
NET-L
DROP
SHIELD
NET-S
NET-C
NET-H
NET-L
DROP
SHIELD
NET-S
NET-C
NET-H
NET-L
BACKBONE
SHIELD
NET-S
NET-C
NET-H
NET-L
1
2
3
4
5
接続箱
JUNCTION BOX
NMEA2000 NETWORK
(BACKBONE)
1
2
3
4
5
DROP
SHIELD
NET-S
NET-C
NET-H
NET-L
BACKBONE
SHIELD
NET-S
NET-C
NET-H
NET-L
1
2
3
4
5
1
2
3
4
5
DROP
SHIELD
NET-S
NET-C
NET-H
NET-L
接続箱
JUNCTION BOX
NMEA2000 NETWORK
(BACKBONE)
FI-5002-POWERCABLE,2m
アカ RED
(VV-SA0.75x2C) クロ BLK
1
2
3
4
5
DROP
SHIELD
NET-S
NET-C
NET-H
NET-L
同上
DITTO
同上
DITTO
FI-50-DROP,6m,φ6
アカ RED
クロ BLK
シロ WHT
アオ BLU
選択
SELECT
同上
DITTO
同上
DITTO
FI-50-DROP,6m,φ6
アカ RED
クロ BLK
シロ WHT
アオ BLU
NOTE
*1: OPTION.
*2: USE A TERMINAL BOX (NO-PROTECTION) WHEN THE SUPPLIED CABLE IS CUT.
*3: PROTECT CABLE ENDS TO PREVENT SHORT-CIRCUIT.
注記
*1)オプション。
*2)ケーブルを切断する場合は、ターミナルボックス(非防水)を使用のこと。
*3)短絡しないように、端末を処理する。
12VDC
12VDC
1 SHIELD
2 (+)
3 (-)
LTW12-05AMMM
-SR7000
LTW12-05AFFM
-SR7000
1
2
3
4
5
1
2
3
4
5
NMEA2K
SHIELD
NET-S
NET-C
NET-H
NET-L
NMEA2K
SHIELD
NET-S
NET-C
NET-H
NET-L
WIND
+V
DIR1
DIR2
SPEED
GND
SHIELD
インスツルメント
INSTRUMENT FI-501/502
3
1
2
3
4
5
DWG.No.
SCALE
1
2
3
4
5
6
C7266-C01- D
MASS
kg
Oct.10'07 R.Esumi
T.TAKENO
T.YAMASAKI
4
REF.No.
LTW12-05AFFM
-SR7000
1
2
3
4
5
NMEA2K
SHIELD
NET-S
NET-C
NET-H
NET-L
インスツルメント
INSTRUMENT FI-501/502
風向風速センサー
WIND TRANSDUCER
FI-5001
NAME
名 称
TITLE
INTERCONNECTION DIAGRAM
INSTRUMENT
相互結線図
FI-501/502/503/504/505/506
インスツルメント
ケーブルや接続条件により満足しない場合あり
DEPEND ON CABLE AND CONNECTION CONDITIONS
FI-50-DROP,6m,φ6
アカ RED
(+)
12VDC (-)
クロ BLK
シロ WHT
NC
*3 NC
アオ BLU
単品で使用するとき
USING INDEPENDENTLY
1
2
3
4
5
6
LTWBD-06AFMM
LR7000 FI-50-SENSOR-30M/50M,30/50m,φ4.3
クロ BLK
チャ BRN
アカ RED
ターミナルボックス
ダイ ORG
TERMINAL BOX *2
キ YEL
FI-5001-TERMINAL
インスツルメント(最大26個)
INSTRUMENT (TOTAL: UP TO 26 SETS)
NMEA2Kケーブル長総合計:80m以下
NMEA2K CABLE TOTAL LENGTH: UP TO 80m
NMEA2K
SHIELD
NET-S
NET-C
NET-H
NET-L
Oct. 9 '07
CHECKED
Oct. 9 '07
APPROVED
DRAWN
LTW12-05AMMM
-SR7000
インスツルメント
INSTRUMENT FI-503/504
505/506
LTW12-05AFFM
NMEA2K
-SR7000
1 SHIELD
2 NET-S
3 NET-C
4 NET-H
5 NET-L
FI-50-CHAIN,0.3m,φ6
(1/5/10/20m *1)
ジャンクションボックス
JUNCTION BOX FI-5002 *1
2
FI-50-CHAIN,0.3m,φ6
(1/5/10/20m *1)
1
S-1
タッピンネジ用穴(4ヵ所)
For tapping screws (4 pcs.)
寸切りボルト用穴(2ヵ所)
For bolts (2 pcs.)
FI-50シリーズ 表示部 フラッシュマウント用型紙
FI-50 series Display unit Flush Mount Template