Specifications | Furuno GP-1650 GPS Receiver User Manual

Back
COLOR DGPS/PLOTTER
COLOR GPS/PLOTTER
GP-1650D, GP-1650 FURUNO/NAVIONICS
GP-1650D, GP-1650 FURUNO/C-MAP NT
C
Your Local Agent/Dealer
9-52, Ashihara -cho,
Nishinomiya, Japan
Telephone:
Telefax:
0 7 9 8 - 6 5 - 2111
0798-65-4200
All rights reserved.
Printed in Japan
P U B . N o . O M E -4 3 9 4 0
( DAMI )
GP-1650/1650D
FIRST
EDITION
N3
:
:
FEB . 1999
OCT 7, 200 2
SAFETY INSTRUCTIONS
CAUTION
WARNING
Do not use the equipment for other than
its intended purpose.
Do not open the equipment.
Hazardous voltage which can
cause electrical shock, burn or
serious injury exists inside the
equipment. Only qualified
personnel should work inside
the equipment.
Use of the equipment as a stepping stool,
for example, can result in personal injury
or equipment damage.
No one navigation device should ever be
solely replied upon for the navigation of
a vessel.
Do not disassemble or modify the
equipment.
Always confirm position against all available
aids to navigation, for safety of vessel and
crew.
Fire, electrical shock or serious injury
can result.
Turn off the power immediately if water
leaks into the equipment or the equipment is emitting smoke or fire.
GPS position and velocity accuracies
are controlled by the U.S. Department of
Defense. Position may be degraded
up to 100 meters.
Continued use of the equipment can cause
fire or electrical shock.
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or illegible, contact
a FURUNO agent or dealer.
Do not place liquid-filled containers on
the top of the equipment.
WARNING
Fire or electrical shock can result if a
liquid spills into the equipment.
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Name: Warning Label (1)
Type: 86-003-1011-0
Code No.: 100-236-230
Do not operate the equipment with wet
hands.
Electrical shock can result.
Keep heater away from equipment.
About the TFT LCD
Heat can alter equipment shape and melt
the power cord, which can cause fire or
electrical shock.
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01%
of the pixels may drop out or blink, however this is not an indication of malfunction.
i
i
TABLE OF CONTENTS
FOREWORD ....................................... iv
SYSTEM CONFIGURATION ....... v
5. WAYPOINTS
5.1
5.2
5.3
5.4
5.5
Entering Waypoints.......................... 5-1
Erasing Individual Waypoints ......... 5-4
Changing Waypoint Data ................. 5-4
Waypoint Mark Size ......................... 5-5
Changing Waypoint Position on the
Plotter Display ................................. 5-5
5.6 Searching Waypoints ....................... 5-5
1. OPERATIONAL OVERVIEW
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Display Unit Controls ....................... 1-1
Inserting Mini Chart Card................. 1-2
Turning the Power On/Off ................ 1-2
Adjusting Tone and Brilliance .......... 1-3
Plotter Displays ................................ 1-3
Menu Operation, Soft Keys ............. 1-4
Demonstration Display .................... 1-5
6. ROUTES
6.1
6.2
6.3
6.4
6.5
2. PLOTTER DISPLAYS
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
Presentation Modes ......................... 2-1
Cursor .............................................. 2-2
Shifting the Display .......................... 2-2
Selecting Chart Scale/Range .......... 2-2
Mini Chart Cards .............................. 2-2
Navigation Data Display .................. 2-5
Steering Display .............................. 2-6
Highway Display .............................. 2-7
Changing Operation Mode .............. 2-8
Navigation Trip Distance .................. 2-8
Entering Routes ............................... 6-1
Connecting Routes .......................... 6-2
Inserting, Removing Waypoints ....... 6-2
Creating Track-based Routes .......... 6-4
Erasing Routes ................................ 6-5
7. NAVIGATION
7.1 Navigating to “Quick Points” ............ 7-1
7.2 Navigating to Waypoints
(waypoint list) ................................... 7-2
7.3 Navigating to Ports, Port Services ... 7-2
7.4 Following a Route ............................ 7-3
7.5 Cancelling Navigation ...................... 7-5
3. TRACK
8. PLOTTER ALARMS
3.1 Displaying Track .............................. 3-1
3.2 Stopping/Restarting Plotting
of Track ............................................ 3-2
3.3 Changing Track Color ...................... 3-2
3.4 Track Plotting Method, Interval ........ 3-2
3.5 Changing Track Memory Capacity .. 3-3
3.6 Erasing All Track .............................. 3-4
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
4. MARK
4.1
4.2
4.3
4.4
4.5
Introduction ...................................... 8-1
Audio Alarm On/Off .......................... 8-1
Arrival Alarm .................................... 8-1
Anchor Watch Alarm ........................ 8-2
XTE (Cross Track Error) Alarm ........ 8-2
Speed Alarm .................................... 8-3
Proximity Alarm ................................ 8-3
Alarm Information ............................ 8-4
9. SAVING AND LOADING
DATA TO/FROM MEMORY
CARD
Entering Marks ................................ 4-1
Changing Mark Attributes ................ 4-2
Changing Mark Size ........................ 4-3
Erasing Marks .................................. 4-3
Displaying Track and Mark Points ... 4-3
9.1 Formatting Memory Cards ............... 9-1
9.2 Saving Data to Memory Card .......... 9-1
9.3 Loading Data from Memory Card .... 9-2
ii
10. CUSTOMIZING YOUR UNIT
10.1
10.2
10.3
10.4
CHART SETUP OPTIONS menu .. 10-1
DISPLAY OPTIONS menu ............. 10-2
GPS/DGPS/TD OPTIONS menu ... 10-4
CONFIGURATION menu ............... 10-7
11.USING C-MAP NT MODEL
11.1 Inserting Chart Card ........................11-1
11.2 Cussor and Data Display ................11-1
11.3 Tidal Information .............................. 11-2
11.4 Navigation to Ports, Port Services ..11-3
11.5 Setting Chart Setup Options ...........11-5
11.6 Selecting Chart Scale/Range .......... 11-6
11.7 Displaying Program Number ...........11-7
12. MAINTENANCE &
TROUBLESHOOTING
12.1
12.2
12.3
12.4
12.5
12.6
Maintenance .................................. 12-1
Replacement of Fuse, Battery ....... 12-2
Simple Troubleshooting ................. 12-2
Error Messages ............................. 12-3
Diagnostic Tests............................. 12-3
Clearing Memories ........................ 12-5
APPENDIX
Menu Tree ................................................ A-1
Loran C Chains ........................................ A-3
Decca Chains ........................................... A-4
World Time ............................................... A-5
Geodetic Chart List .................................. A-6
SPECIFICATIONS ....................... SP-1
INDEX
Declaration of Conformity
iii
FOREWORD
A Word to GP-1650D/1650
Owners
Features
The GP-1650D is a totally integrated DGPS
beacon receiver, GPS receiver, and color
video plotter. The GP-1650 mostly shares the
same features with the GP-1650D except it
does not have a built-in DGPS beacon receiver.
Congratulations on your choice of the
FURUNO GP-1650D COLOR DGPS/PLOTTER, GP-1650 COLOR GPS/PLOTTER. We
are confident you will see why the FURUNO
name has become synonymous with quality
and reliability.
Navigation information is displayed on a
bright 5.6-inch color TFT LCD. On-screen information shown are position, range and
bearing to cursor position, range, bearing,
ETA and TTG to waypoint, etc.
For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for
innovative and dependable marine electronics equipment. This dedication to excellence
is furthered by our extensive global network
of agents and dealers.
A high sensitivity receiver tracks up to twelve
satellites simultaneously. An 8-state Kalman
filter ensures optimum accuracy in determination of vessel position, course and speed.
C-MAP NT-FP chart card is available for the
GP-1650/1650D C-MAP NT.
This equipment is designed and constructed
to meet the rigorous demands of the marine
environment. However, no machine can perform its intended function unless installed, operated and maintained properly. Please
carefully read and follow the recommended
procedures for operation and maintenance.
The main features of the GP-1650D/GP-1650
are
• Comprehensive navigation data displays.
We would appreciate hearing from you, the
end-user, about whether we are achieving our
purposes.
• Bright 5.6-inch color TFT LCD with temperature compensated tone and brilliance
control.
Thank you for considering and purchasing
FURUNO equipment.
• Automatic coastline chart loading.
• Position display in latitude and longitude,
Loran C or Decca TDs.
• Improved position accuracy with optional
DGPS beacon receiver (GP-1650).
• Accepts both FURUNO and NAVIONICS
or C-MAP NT mini chart cards.
• Alarms: Arrival, Anchor Watch, Cross-track
Error, Speed, Proximity.
• Man overboard feature records latitude
and longitude coordinates at time of man
overboard.
• “Highway” display provides graphic presentation of ship’s track and is useful for
monitoring cross track error.
iv
SYSTEM CONFIGURATION
ANTENNA UNIT GPA-018
(GP-1650D)
ANTENNA UNIT GPA-019
(GP-1650D)
1.2 m Whip Antenna
(option)
ANTENNA UNIT GPA-017
(GP-1650)
ANTENNA UNIT
Receives signal from
GPS satellite and beacon
reference station (GP-1650D
only).
DISPLAY UNIT
Ship’s position is
calculated in longitude
and latitude from signal
received from the antenna unit and displayed
on the screen.
Ship’s mains
10.8—31.2 VDC
External equipment
(Autopilot, etc.)
DGPS beacon receiver
GP-1650 only
v
This page is intentionally left blank.
1. OPERATIONAL OVERVIEW
This chapter acquaints you with the basics of your unit - from turning on the power to the soft
key menu operation.
1.1
Display Unit Controls
• Registers own ship's position.
• Marks man overboard position, event position.
Cursor pad
• Shifts cursor and display.
Registers items
on menus.
• Selects items on menus.
SAVE
MOB
ENTER
Soft key's functions change
depending on the display.
POWER
BRILL
ALARM
PLOT
XTE
HIWAY
WPT
RTE
ABC
1
DEF
2
GHI
3
JKL
4
MNO
5
PQR
6
STU
7
VWX
8
YZ&
9
CLEAR
_'#
0
MENU
Enter alphanumeric data.
Opens/closes
the main menu.
Mini chart card slot.
HIDE
SHOW
• Clears data.
• Erases selected waypoint.
• Silences audible alarm.
Displays/hides the soft key menu,
nav data, mode indication.
Displays the waypoint & route
menu.
Alternately displays Steering Display,
Highway Display.
Selects plot display.
Displays the alarm menu.
• Long press: Turns power on/off.
• Touch and release: Opens the display for adjustment of tone and brilliance.
Figure 1-1 Display unit
1-1
1.2
Inserting Mini Chart Card
Insert appropriate mini chart card before turning on the power.
1. Push down the lid catch to open the mini
chart card slot cover.
Your equipment takes about 90 seconds to
find its position when turned on for the very
first time. This is because the equipment has
no satellite data, called the Almanac, in its
database. If you want to lessen the time
needed to find position you may enter your
position manually (default position: San Francisco, USA) on the GPS SETUP OPTIONS
menu.
Thereafter it takes about 12 seconds to find
position each time the power is turned on.
Card slot
Figure 1-2 Location of mini chart
card slot cover
2. Insert appropriate mini chart card groove
side up.
3. Close the slot cover to protect the chart
drive. (Keep the slot cover closed at all
times.)
Note: Turn off power before inserting or ejecting the mini chart card.
1.3
Turning the Power On/Off
Press the [POWER/BRILL] key at bottom lefthand side of the display unit to turn on the
power. When the unit is turned on, it proceeds
in the sequence shown in Figure 1-3, after
displaying the FURUNO information display.
Displayed for about five seconds.
When the satellite signal is being received
normally, the equipment displays various abbreviations at the bottom left-hand corner of
the display which show DGPS/GPS receiver
status. Table 1-1 shows these abbreviations
and their meanings.
Table 1-1 Display abbreviations
Indication
Meaning
GPS 2D
Normal 2D
(dimension) GPS
position fix
GPS 3D
Normal 3D GPS
position fix
DGPS 2D
(GP-1650D)
Normal 2D differential
GPS position fix
DGPS 3D
(GP-1650D)
Normal 3D differential
GPS position fix
NO FIX
Position can not be
found.
DOP
DOP error
DEMO
Simulation mode
START UP TEST
PROGRAM
OK
RAM
OK
BACKUP DATA
OK
INTERNAL BATTERY
OK
GPS
OK
— — WARNING — —
NO NATIONAL HYDROGRAPHIC OFFICE
HAS VERIFIED THE INFORMATION
IN THIS COASTLINE DATA CARD AND
NONE ACCEPT LIABILITY FOR THE
ACCURACY OF REPRODUCTION OR ANY
MODIFICATIONS MADE THEREAFTER.
THIS PRODUCT WITH THIS COASTLINE
DATA CARD DOES NOT REPLACE THE
REQUIREMENT TO USE THE
APPROPRIATE PRODUCTS FOR
NAVIGATION ACCORDING TO NATIONAL
AND INTERNATIONAL REGULATONS.
FURUNO ELECTRIC CO., LTD.
Displayed for about 30 seconds,
or press any key to escape.
The last-used display appears.
Figure 1-3 Start-up sequence
1-2
Turning the power off
Press and hold down the [POWER/BRILL]
key until the screen goes blank. The time
remaining until the power is turned off is
shown on the screen.
1.4
Adjusting Tone and
Brilliance
NORTH
UP
ZOOM
IN
ZOOM
OUT
1. Press the [POWER/BRILL] key with a
touch-and-release action. The tone and
brilliance setting menu appears.
COURSE
UP
WP-002
FISH
Functions
BRIDGE
NAV
POS
DGPS 3D
[Plotter Display]
TONE
TONE
TONE
DATE: OCT 21 1998
POSITION
BRILL
BRILL
TIME 23:59:59
LAT/LON
34° 56.789’ N
135° 56.789’ E
BRILL
SPD
TD
RNG
16.3
RETURN
LAT
LON
27.2 NM
KT
CSE
ZOOM
BRG
245.8°
245.0°
SAT
INFO
DATUM: WGS-84
BEACON
INFO
Tone and display brilliance setting menu
Soft keys
Figure 1-4 Tone and
brilliance adjustment screen
TMP
65.8°F
DEP
20ft
DGPS 3D
[Nav Data Display]
2. Press t or s to adjust display tone.
3. Press ▲ or ▼ to adjust display brilliance.
Note that tone and brilliance can also be adjusted by soft keys. After pressing the
[POWER/BRILL] key, use the appropriate soft
key to adjust tone or brilliance.
Note: Tone or brilliance must be adjusted
within 10 seconds after pressing the
[POWER/BRILL] key or the tone and brilliance adjustment screen will be erased.
230
240
245.0°
234.5°
BRG
CSE
TTG
0.1NM
XTE
260
27.2
13.6
29th 14:50
0.1NM
000.02nm
EDIT
XT-LMT
[Steering Display]
CSE
87.8°
BRG
RNG
SPD
94.6°
1.88nm
10.0kt
001WPT
YUUKI
0.1NM
XTE
HIGHWAY
FISH01
000.02nm
DGPS 3D
Press the [PLOT] key. Each time this key is
pressed, the display mode changes in the sequence shown below.
nm
kt
DGPS 3D
001WPT
Selecting a display
250
RNG
SPD
ETA
1h 59m
1.5 Plotter Displays
There are four types of plotter displays: Plotter display, Navigation data display, Steering
display and Highway display. For details, refer to Chapter 3.
CROSS
TRACK
QP<01>
0.1NM
EDIT
XT-LMT
[Highway Display]
Figure 1-5 Display modes (plotter)
1-3
Steering display, Highway display
MENU
CHART SETUP OPTIONS
Press the [XTE/HIWAY] key to display the
Steering display, Highway display alternately.
DISPLAY OPTIONS
Soft
keys
GPS/DGPS/TD OPTIONS
CROSS
TRACK
QP<01>
230
240
27.2
13.6
RNG
SPD
ETA
1h 59m
0.1NM
260
Figure 1-7 Main menu
245.0°
234.5°
BRG
CSE
TTG
250
CONFIGURATION
DGPS 3D
XTE
nm
kt
29th 14:50
000. 02nm
DGPS 3D
0.1NM
EDIT
XT- LMT
2. Press appropriate soft key to display desired menu. For example, press the soft
key CHART SETUP OPTIONS. The
menu in use appears at the top right corner of the display.
CHART
SETUP
[Steering Display]
CHART OFFSET
TRACK CONTROL
001WPT
CSE
87.8°
BRG
RNG
SPD
94.6°
1.88nm
10.0kt
001WPT
YUUKI
CHART DETAILS
HIGHWAY
DGPS 3D
FISH01
RETURN
Figure 1-8 Chart setup options menu
0.1NM
XTE
000. 02nm
DGPS 3D
0.1NM
EDIT
XT-LMT
3. Select menu with the soft keys. For examples press the soft key TRACK CONTROL to display the track control menu.
[Highway Display]
s DISPLAY
Figure 1-6 Steering display,
Highway display
TRACK ON
TRACK COLOR WHITE
PLOT
TIME
TIME INTERVAL 01m00s
DIST INTERVAL 00.10 nm
TRACK MEMORY 2000 POINTS
(MARK MEMORY) (3000) POINTS
TRACK STATUS
TRACKING
1.6
Menu Operation, Soft Keys
TRACK : 1000 / 2000 PTS used
MARK :
5 / 3000 PTS used
TRACK
CONTROL
EDIT
STOP
TRACK
ERASE
TRACK
ERASE
MARK
RETURN
Most operations are carried out through the
menu. The menu is opened and closed with
the [MENU] key. Menus may be selected with
the five soft keys to the right of menus. Options are selected with the cursor pad.
1. Press the [MENU] key to display the main
menu.
1-4
DGPS 3D
Figure 1-9 Track control menu
4. Use the cursor pad to select item, and
then press the soft key EDIT. For example,
select TRACK COLOR. The track color
window appears.
4. Press the soft key labeled EDIT to show
the demo mode window.
DEMO MODE
TRACK COLOR
▲
▲
ON
™ OFF
▼
'
RED
™ YELLOW
™ GREEN
™ LIGHT BLUE
™ PURPLE
™ BLUE
™ WHITE
▼
'
Figure 1-13 Demo mode window
5. Press ▲ to select ON.
Figure 1-10 Track color window
5. Use the cursor pad to select option.
6. Press the soft key RETURN to finish.
1.7
3. Press ▲ or ▼ to select DEMO MODE.
Demonstration Display
The demonstration display provides simulated operation of this unit. On the plotter display, own ship tracks, at the speed selected,
a figure eight course or any course you enter, starting from position entered. All controls
are operative; you may set destination, enter waypoints, etc.
1. Press the [MENU] key, followed by the soft
keys CONFIGURATION and SYSTEM
MENU to open the system menu.
6. Press the soft key ENTER or the [ENTER]
key.
7. Select DEMO SPEED and press the soft
key EDIT. Enter speed with the cursor
pad. Select digit with t/sand enter value
with numeric key.
8. Select DEMO COURSE and press the
soft key EDIT. Select how you want the
courseline to be traced; by FIGURE 8 or
DIR.(ection). For DIR., enter course.
9. Select DEMO START LAT., and press the
soft key EDIT. Enter current latitude.
10.Select DEMO START LONG., and press
the soft key EDIT. Enter current longitude.
11. Press the soft key RETURN to finish.
To cancel the demonstration display, set
DEMO MODE to OFF.
2. Press the soft key DEMONSTRATION
MODE to open the demonstration setting
screen.
s DEMO
MODE
DEMO SPEED
DEMO COURSE
DEMO START LAT
DEMO START LON
DGPS 3D
OFF
10.0kt
000.0°
34°12.34’N
135°12.34’E
DEMO
MODE
EDIT
RETURN
Figure 1-11 Demo setting screen
1-5
This page is intentionally left blank.
2. PLOTTER DISPLAYS
2.1
Course-up
Presentation Modes
The plotter display mainly shows chart, ship’s
track, waypoints, and navigation data.
Three types of display presentations are provided for the normal plotter display: north-up,
course-up and auto course-up. To change the
mode, use the presentation mode selection
soft key, which is the 3rd soft key from the
top.
North-up
Press the soft key COURSE UP to show the
course-up display. When destination is set it
is at the top of the screen, the north mark
appears at the upper left side of the screen
and points to north. A filled triangle marks own
ship’s position.
When destination is not set, the course or
heading is upward on the screen at the moment the course-up mode is selected.
34° 12.345’ N
135° 12.345’ E
Press the soft key NORTH UP to show the
north-up display. North (zero degree) is at the
top of the display and own ship is at the center of the screen. Own ship marker is a filled
circle. This mode is useful for long-range
navigation.
Functions for
soft key
Course bar
34° 12.345’ N
135° 12.345’ E
CSE 245.8°
SPD 16.3kt
NORTH
UP
ZOOM
IN
ZOOM
OUT
COURSE
UP
FISH
BRIDGE
ZOOM
IN
ZOOM
OUT
AUTO
C.U.
NAV
WPT
DGPS 3D
Figure 2-2 Plotter display, course-up mode
Auto course-up
Press the soft key AUTO C.U. to show the
automatic course-up display. The course or
heading is at the top of screen at the moment the course-up mode is selected. When
own ship is off its intended course by 22.5°
or more, it is automatically brought back to
perpendicular.
NAV
WPT
DGPS 3D
GPS status
QP<01>
COURSE
UP
Current display mode
(north-up)
Track
Nav information
window
002WP
CSE 245.8°
SPD 16.3kt
Icon (chart)
Own ship
marker
34° 12.345’ N
135° 12.345’ E
CSE 245.8°
SPD 16.3kt
AUTO
C-UP
ZOOM
IN
Waypoint name
Waypoint mark
ZOOM
OUT
NORTH
UP
Figure 2-1 Plotter display, north-up mode
DGPS 3D
NAV
WPT
Figure 2-3 Auto course-up mode
2-1
2.2
Cursor
2.4
Turning on the cursor, shifting the
cursor
Press the cursor pad to turn the cursor on,
and the cursor appears at the own ship’s position. Operate the cursor pad to shift the
cursor. The cursor moves in the direction of
the arrow or diagonal pressed on the cursor
pad.
Cursor state determines what data is shown
on the display. Cursor position is displayed
in latitude and longitude or Loran or Decca
TDs (depending on menu setting) at the top
of the plotter display when the cursor is on.
34° 12.345’ N
135° 12.345’ E
FROM 16.45nm
OS
276.9°
NORTH
UP
ZOOM
IN
ZOOM
OUT
COURSE
UP
GO TO
CURSOR
DGPS 3D
CENTER
Figure 2-4 Data displayed on the plotter
display when the cursor is on
Chart scale (range) may be selected with the
soft key ZOOM IN or ZOOM OUT. ZOOM IN
expands the chart; ZOOM OUT shrinks it.
Note: When the display is expanded or
shrunk beyond the range of the chart card in
use NO CHART appears, along with the appropriate chart icon. See Table 2-1.
2.5
The soft key CENTER turns off the cursor
and returns own ship marker to screen center.
2.3
Shifting the Display
The display can be shifted on the plotter display.
1. Press the cursor pad to display the cursor.
2. Locate the cursor at a screen edge. The
screen shifts in the direction opposite of
cursor location.
2-2
Mini Chart Cards
The mini chart cards contain nautical charts.
When you insert a suitable mini chart card in
the slot and your boat is near land, a chart
appears.
When a wrong card is inserted or a wrong
chart scale is selected, the land will be hollow. Insert the proper card and select a suitable chart scale. Chart icons appear to help
you select a suitable chart scale. Table 2-1
shows the chart icons and their meanings.
Table 2-1 Chart icons and their meanings
Icon
Turning off the cursor, returning
own ship marker to screen center
Selecting Chart
Scale/Range
Meaning
Proper card is not inserted or
chart scale is too small. Press
the ZOOM IN soft key to
adjust chart scale.
Chart scale is too large. Press
the ZOOM OUT soft key to
adjust chart scale.
Suitable chart scale is
selected.
Indices and chart enlargement
Chart symbols
When the soft key ZOOM OUT is used, you
will see several frames appear on the chart.
These frames are called indices and they
show you what parts of the chart can be enlarged in the current picture range. The areas circumscribed with smaller frames can
be enlarged, but the area enclosed by the
largest frame cannot.
FURUNO mini chart card
The table below shows FURUNO mini chart
symbols and their meanings.
Table 2-2 FURUNO chart symbols
Symbol
Description
Summit
Wreck
Lighthouse
Lighted Buoy
Buoy
Radio Station
Position of Sounding
Figure 2-5 Sample chart (Japan and South
Korea) showing indices
Obstruction
Fishing Reef
Remarks on chart display
Platform
A chart will not be displayed in the following
conditions:
Anchorage
• When the chart scale is too large or too
small.
• When scrolling the chart outside the indices.
When this happens, select proper chart scale.
2-3
Table 2-3 Comparison of FURUNO and
Nav-Charts™ chart cards
Item
FURUNO
Dot scrolling
capability
YES
Course-up
display
YES
Nav-Charts™
Range and bearing
from own ship
YES
YES
Lighthouse data
YES *3
presentation
YES
Zoom at cursor
position
YES
*1
0.125, 0.5,
1, 2... 2048
nm
Same as left
Chart offset
data entry
YES
YES
Centering
YES
*2
Range at
Equator
Example of data displayed
Period (ex.: 6 seconds)
Visibility in nautical
mile (ex.: 12 miles)
NAVAID: /FL 6S 12M
FROM OS
52.38nm 48.0°
FL : Flashing
F
: Fixed light
F FL : Fixed and Flashing light
MO : Morse code light
Oc : Occulting light
Figure 2-7 Example of buoy,
lighthouse data
*1 Nav-Charts™ chart may not center the
cursor perfectly.
*2 Nav-Charts™ chart may not center own
ship's position perfectly.
*3 Newly designed chart cards containing
lighthouse data. Chart cards for North
America area are completed, and others
are in production.
*4 Nav-Charts™ is the resistered trademark
of NAVIONICS INC.
Port service icons (Nav-Charts™
cards)
Selected Nav-Charts™ mini chart cards show
by icons services available at ports. Use the
cursor pad to place the cursor on the sailboat icon (denotes a port or harbor), and then
press the [ENTER] key. The services available appear at the top of the display.
Detailed information of service
selected
List of services
at the port selected
NORTH
UP
Aid to navigation data
FIRST AID
Selected FURUNO and Nav-Charts™ mini
chart cards can show buoy and lighthouse
data. Simply place the cursor on the lighthouse or buoy mark.
DGPS 3D
Place the cursor on
a lighthouse or buoy mark.
Figure 2-6 Placing the cursor on the mark
2-4
CANCEL
Sailboat mark (Port)
Figure 2-8 Plotter display showing NavCharts™ port service display
Enlarging an indication
Emergency
medical service
Fueling station
Water
supply station
Traveler’s
service station
An indication on the screen may be enlarged
as follows:
1. Use the cursor pad to select the indication which you wish to enlarge. Selected
indication is circumscribed with a red cursor.
2. Press the soft key ZOOM.
To return to the normal nav data display, press
the soft key RETURN.
Customer
service station
Marine
equipment service
GPS satellite monitor display
The GPS satellite monitor display shows information about GPS satellites.
Information center
Port
Figure 2-9 Port service icons
2.6
Press the soft key SAT INFO. Your display
should look something like the following illustration.
Receive signal level
Bars show satellite
signal level. Satellites
extends past the
dashed line are used
in fixing position.
Navigation Data Display
Date
The navigation data display provides generic
navigation data and DPGS/GPS information.
Press the [PLOT] several times to show the
navigation data display.
DATE: OCT 21 1998
TIME 23:59:59
N
SAT
No. 30
08
05
12
21
07
20
W
Position Date
DATE: OCT 21 1998
POSITION
Range to waypoint
TIME 23:59:59
TRIP:123nm
34° 56.789' N
135° 56.789' E
SPD
11
50
21
07
06
11
03
05
12
08
20
03
LAT/LON
S
LAT
LON
ALT
5m
DOP 2.0
RETURN
DGPS 3D
TD
RNG
12.5
123.25 nm
kt
CSE
BRG
359.9°
65.8°F
ZOOM
299.9°
SAT
INFO
DATUM: WGS-84
TMP
E
06
SAT
INFO
SNR
40
DEP
DGPS 3D
Temperature, depth
Geodetic chart
Course
Speed
20.8ft
GPS fix
state
Altitude
DOP value
Estimated position in the sky, and
satellite number in reverse video is
used for positioning.
BEACON
INFO
Bearing to waypoint
Figure 2-11 GPS satellite monitor display
To return to the normal navigation data display, press the soft key RETURN.
Figure 2-10 Navigation data display
Navigation data display shows the position
by L/L or TD (Loran-C, Decca). To change
position format, press the appropriate soft key
LAT/LON or TD.
2-5
Beacon information display
2.7
Equipped with a DGPS beacon receiver, your
unit can show DGPS reference station information. Press the soft key BEACON INFO to
show the DGPS reference station information.
The steering display provides steering information such as range, bearing, ETA to destination, course and speed.
DGPS reference station information
Receive data status
Beacon receiver setting status
MODE
FREQ
BAUD
RATE
AUTO SEARCH
288.0kHz
BEACON
INFO
200 BPS
RECEIVED DATA:
BEACON STATION:
OK
OK
SS
75
SN
19
Steering Display
Press the [XTE/HIWAY] key to show the
steering display.
Course
Compass bearing
Estimated time of arrival
Speed
Range from own ship to waypoint
Waypoint name
Bearing from
own ship to
waypoint
CROSS
TRACK
001-WP
230
DGPS 3D
Course indicator
Bearing to waypoint
240
250
260
RETURN
Signal strength (SS),
Signal to noise ratio (SN)
BRG
CSE
TTG
245.0°
234.5°
1h 59m
RNG
SPD
ETA
27.2
13.6
nm
kt
29th 14:50
Figure 2-12 Beacon information display
SS: SS (Signal Strength) displays a numeric
representation of field strength of the received
signal on the selected frequency. The higher
the number the stronger the received signal.
If noise is present at reception band width,
the figure gets bigger.
SN: SN (Signal-to-Noise) ratio displays the
ratio between the desired signal and unwanted noise on the selected frequency. The
higher the SN ratio the better the quality of
the signal.
Note: If your equipment does not have a
DPGS receiver, the message “NO DIFFERENTIAL DATA” appears when the soft key
BEACON INFO is pressed.
2-6
0.1NM
DGPS 3D
XTE
indication
range
XTE
000.02nm
0.1NM
EDIT
XT-LMT
Indicates the
direction to steer
Own ship
Amount of XTE in nautical miles
XTE scale
Time-to-go to waypoint
Figure 2-13 Steering display
How to read the compass display
The solid inverted triangle at the center of
the compass shows own ship’s course (heading). The hollow inverted triangle shows the
bearing to destination waypoint. When own
ship’s course is changed, the hollow inverted
triangle moves with course change.
How to read the XTE scale
2.8
The black boat-shaped mark shows own
boat’s movement and direction, and amount
to steer to return to course. Using Figure 213 as an example, you would steer right by
000.02 nautical miles to return to course.
When this mark is out of range of the XTE
scale, the mark color changes from black to
yellow. The range of the XTE scale can be
set as shown below (default: 0.5 nm).
The highway display provides a graphic presentation of ship’s track along intended
course. It is useful for monitoring XTE - the
XTE scale shows direction and amount in
nautical miles to steer to return to course. In
the figure below, for example, you would steer
right by 0.02 nm to return to course.
Setting the range of the XTE scale
1. Press the soft key EDIT XT-LMT to display the following window.
EDIT XTE LIMIT
Highway Display
Press the [XTE/HIWAY] key to show the highway display.
Course
Speed
Range to waypoint
Bearing to waypoint
Waypoint mark
& name
001WPT
CSE 87.8
BRG
RNG
SPD
94.6°
1.88nm
10.0 kt
WPT001
0 .1nm
YUUKI
0.1NM
Figure 2-14 XTE range setting window
2. Use the cursor pad to select digit to
change.
3. Press appropriate alphanumeric key.
DGPS 3D
XTE
indication
range
XTE
HIGHWAY
FISH01
0.02nm
0.1NM
EDIT
XT- LMT
Indicates the
direction to steer Own ship
Amount of XTE in nautical miles
4. Repeat steps 2 and 3.
5. Press the [ENTER] key. To cancel entry,
press the soft key CANCEL.
Waypoint
Figure 2-15 Highway display
Note that all digits may be cleared by pressing the [CLEAR] key.
2-7
2.9
Changing Operation Mode
Operation mode can be changed between
PLEASURE and FISHING. FISHING mode
provides mark/line entry on the PLOTTER
display. The mark can be entered up to 5000
points together with tracks. The apportion
between track and mark memory can be
changed at menu. Pressing the [HIDE/
SHOW] key changes the function of soft keys.
Holding track, changing track color, and selecting color and form of mark/line can be
performed by the soft keys directly.
2.10 Navigation Trip Distance
The navigation trip distance is displayed at
the navigation data display. Press the [PLOT]
key several times to show the navigation
data display.
Trip
DATE: OCT 21 2000
POSITION
34° 56.789' N
135° 56.789' E
SPD
RHUMB LINE
nm / kt
ft
F
DD MM.MMM'
24 HOUR
AUTO2
LINE
MAGNETIC
AUTO 01.3 E
LORAN C
LAT/LON
1 POINT
PLEASURE
CSE
123.25 nm
299.9°
BRG
DATUM: WGS-84
TMP
DISPLAY
SETUP1
65.8°F
EDIT
LAT/LON
LAT
LON
TD
ZOOM
SAT
INFO
DEP
20.8ft
DGPS 3D
BEACON
INFO
Figure 2-19 Navigation data display
Note: When you enlarge POSITION, TRIP is
not displayed.
You can reset the trip distance as follows.
1.
Press the [MENU] key followed by the
soft keys CONFIGURATION and SYSTEM MENU.
2.
Press the soft key MEMORY/TRIP
CLEAR to open the clear memory menu.
RETURN
DGPS 3D
RNG
12.5 kt
359.9°
1. Press the [MENU] key and the soft key
DISPLAY OPTIONS. The display setup1
menu appears.
RNG & BRG MODE
RANGE/SPEED UNIT
DEPTH UNIT
TEMP UNIT
LAT/LON DISPLAY
TIME DISPLAY
WAYPOINTS SW
COURSE VECTOR
BEARING
MAG VARIATION
TD DISPLAY
POSITION DISPLAY
SET GO TO METHOD
s OPERATION MODE
TIME 23:59:59
TRIP: 4792 nm
Figure 2-16 Display setup1 menu
2. Press ▼ to select OPERATION MODE.
CLEAR PLOTTER MEMORY NO
3. Press the soft key EDIT to show the OPERATION MODE window.
CLEAR GPS MEMORY
NO
CLEAR ALL MEMORY
NO
TRIP METER RESET
NO
CLEAR
MEMORY
EDIT
OPERATION MODE
▲
' PLEASURE
™ FISHING
▼
DGPS 3D
RETURN
Figure 2-17 OPERATION MODE window
4. Press ▲ or ▼ to select PLEASURE or
FISHING.
3.
Press 6 to select TRIP METER RESET.
5. Press the soft key ENTER or the [ENTER]
key to finish.
4.
5.
Press the soft key EDIT.
Press 5 to select YES.
Figure 2-20 Clear memory menu
6. Press the soft key ENTER or the
[ENTER] key to clear memory selected.
2-8
3. TRACK
3.1
Displaying Track
s DISPLAY
1. Press the [MENU] key to open the main
menu.
MENU
TRACK ON
TRACK COLOR WHITE
PLOT
TIME
TIME INTERVAL 01m00s
DIST INTERVAL 00.10 nm
TRACK MEMORY 2000 POINTS
(MARK MEMORY) (3000) POINTS
TRACK STATUS
CHART SETUP OPTIONS
TRACKING
TRACK : 1000 / 2000 PTS used
MARK :
5 / 3000 PTS used
DISPLAY OPTIONS
TRACK
CONTROL
EDIT
STOP
TRACK
ERASE
TRACK
ERASE
MARK
RETURN
GPS/DGPS/TD OPTIONS
DGPS 3D
Figure 3-3 Track control menu
DGPS 3D
4. Press ▲ to select DISPLAY TRACK.
CONFIGURATION
Figure 3-1 Main menu
5. Press the soft key EDIT to show the display track window.
2. Press the soft key CHART SETUP OPTIONS to open the chart setup menu.
6. Press ▲ or ▼ to select ON or OFF as
appropriate.
CHART
SETUP
CHART OFFSET
8. Press the [PLOT] key to close the menu.
TRACK CONTROL
The default setting is ON which traces ship’s
track in accordance with ship’s movements.
CHART DETAILS
DGPS 3D
7. Press the soft key ENTER or the [ENTER]
key.
RETURN
Figure 3-2 Chart setup menu
Number of track and mark points used appears at the TRACK STATUS window on the
TRACK CONTROL display. In case of figure
3-3, track memory is recorded 1000 points
(max. 2000 points) and mark memory is recorded 5 points (max. 3000 points).
3. Press the soft key TRACK CONTROL to
open the track control menu.
3-1
3.2
Stopping/Restarting
Plotting of Track
TRACK COLOR
▲
' RED
™ YELLOW
™ GREEN
™ LIGHT BLUE
™ PURPLE
™ BLUE
™ WHITE
▼
When your boat is at anchor or returning to
port you probably won’t need to record its
track. You can stop recording the track, to
conserve the track memory, as follows:
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press the soft key STOP TRACK. The indication “TRACKING” in the TRACK STATUS window changes to “NOT
TRACKING”.
To restart recording the track, press the soft
key START TRACK at step 2 in the above
procedure.
When the fishing mode is selected, you can
stop or restart plotting the track with the soft
key only on the plotter display. Press the
[SHOW/HIDE] key several times to show the
soft key STOP TRACK. Press the soft key
STOP TRACK on the plotter display to stop
plotting of track. HOLD TRACK PLOTTING
appears approx. 2 seconds and own ship
mark changes to hollow circle. To restart plotting the track, press the soft key START
TRACK. START TRACK PLOTTING appears
approx. 2 seconds and the plotting restarts.
3.3
Changing Track Color
Track can be displayed in red, yellow, green,
light-blue, purple, blue or white. It can be useful to change track color on a regular basis
to discriminate between previous day's track,
past track, etc.
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press ▲ or ▼ to select TRACK COLOR.
3. Press the soft key EDIT to display the
track color window.
Figure 3-4 Track color window
4. Press ▲ or ▼ to select the color desired.
5. Press the soft key ENTER to finish.
When the fishing mode is selected, you can
change track color with the soft key only on
the track display.
1. Press the [SHOW/HIDE] key several
times to show the soft key TRACK
COLOR.
2. Press the soft key TRACK COLOR to
show the TRACK COLOR window.
3. Press ▲ or ▼ to select the color desired.
4. Press the soft key ENTER or the [ENTER]
key to finish, or press the soft key CANCEL to escape.
3.4
Track Plotting Method,
Interval
In drawing the track, first the ship’s position
(fed from the DGPS/GPS receiver) is stored
into the unit’s memory at an interval of time
or distance. A shorter interval provides better reconstruction of the track, but the storage time of the track is reduced. When the
track memory becomes full, the oldest track
is erased to make room for the latest.
Track plotting method
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press ▲ or ▼ to select PLOT.
3. Press the soft key EDIT to display the plot
window.
3-2
PLOT
▲
' TIME
™ DISTANCE
▼
Figure 3-5 Plot window
4. Press ▲ or ▼ to select TIME or DISTANCE. Distance is useful for conserving track memory, since no track is
recorded when the boat is stationary.
5. Press the soft key ENTER or the [ENTER]
key.
Track plotting interval
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press ▲ or ▼ to select TIME INTERVAL
or DIST INTERVAL.
3.5
Changing Track Memory
Capacity
The equipment stores a total of 5000 points
of track and marks. This total may be freely
apportioned as desired. The default setting
is 2000 points of track and 3000 marks. You
can change the memory capacity for track
and marks. Note that when this is done all
tracks and marks in the memory are erased.
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press ▼ to select TRACK MEMORY.
3. Press the soft key EDIT to display the
TRACK MEMORY window.
TRACK MEMORY
1000/5000 POINTS
3. Press the soft key EDIT to display the interval window.
Figure 3-7 TRACK MEMORY window
TIME INTERVAL
01 m 00 s
(When selecting TIME INTERVAL.)
DIST INTERVAL
00.10 nm
(When selecting DIST INTERVAL.)
Figure 3-6 Interval window
4. Use the cursor pad to place the cursor on
the digit desired. The [CLEAR] key functions to clear an entire line of data.
5. Press appropriate alphanumeric key to
enter value.
6. Repeat steps 4 and 5 to complete.
7. Press the soft key ENTER or the [ENTER]
key.
The TRACK MEMORY window may be
erased by pressing the soft key CANCEL
to escape.
4. Enter number of track memory points
desired with the alphanumeric keys.
Note that all digits may be cleared by
pressing the soft key CLEAR or the
[CLEAR] key in entering track memory
points.
5. Press the soft key ENTER or the [ENTER]
key. The following window appears to ask
you if you are sure to change the track
memory capacity.
RESETTING ERASES
TRACK, MARK/LINE
ALREADY SAVED. OK?
YES ... "ENTER" key
NO ... "CLEAR" key
Figure 3-8 ERASE messege
6. Press the [ENTER] key to change apportion, or press the [CLEAR] key to escape.
3-3
3.6
Erasing All Track
You can erase all track. Be absolutely sure
you want to erase all track; erased track cannot be restored.
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press the soft key ERASE TRACK. You
are asked if you sure to erase all track.
3. Press the [ENTER] key to erase, or press
the [CLEAR] key to escape.
3-4
4. MARK
4.1
Entering Marks
Select the fishing mode to enable entry of
marks on the PLOTTER display. Select the
location desired with the cursor, or turn off
the cursor to enter the mark at own ship position. Pressing the [HIDE/SHOW] key
changes the function of the soft keys. Press
the soft key MARK ENTRY to enter the mark.
The mark is entered in the shape and color
selected from the MARK SHAPE and MARK
COLOR windows.
In the FISHING mode, pressing the [HIDE/
SHOW] key changes the function of the soft
keys as follows.
34° 12.345’ N
135° 12.345’ E
CSE 245.8°
SPD 16.3kt
COURSE
UP
ZOOM
QP<01>
IN
ZOOM
OUT
AUTO
C.U.
NAV
WPT
DGPS 3D
Press the [HIDE/SHOW] key.
34° 12.345’ N
135° 12.345’ E
CSE 245.8°
SPD 16.3kt
COURSE
UP
STOP
TRACK
QP<01>
TRACK
COLOR
MARK
ENTRY
MARK
EDIT
Soft key
to enter mark.
NAV
WPT
DGPS 3D
Press the [HIDE/SHOW] key.
34° 12.345’ N
135° 12.345’ E
CSE 245.8°
SPD 16.3kt
COURSE
UP
QP<01>
DGPS 3D
Press the [HIDE/SHOW] key.
QP<01>
DGPS 3D
Press the [HIDE/SHOW] key.
Figure 4-1 Changing displays
4-1
4.2
Changing Mark Attributes
MARK LINE
▲
'
You can select shape, line and color of mark/
line on the TRACK display.
™
™
™
▼
1. Press the [HIDE/SHOW] key to show the
soft key MARK EDIT.
2. Press the soft key MARK EDIT to show
the MARK/LINE window.
MARK SHAPE
.
MARK LINE
MARK COLOR
YELLOW
Figure 4-2 MARK/LINE window
3. Press the soft key MARK SHAPE to
change mark shape, the soft key MARK
LINE to change mark line, or the soft key
MARK COLOR to change mark color.
Mark shape
Press the soft key MARK SHAPE to display the MARK SHAPE window. Press ▲
or ▼ to select mark shape desired.
MARK SHAPE
▲
' ™
™
™
™ ✕
™
™
™
▼
Figure 4-3 MARK SHAPE window
Mark line
Press the soft key MARK LINE to display
the MARK LINE window. Press ▲ or ▼ to
select mark line desired.
4-2
Figure 4-2 MARK LINE window
Mark color
Press the soft key MARK COLOR to display the MARK COLOR window. Press
▲ or ▼ to select mark color desired.
MARK COLOR
▲
' RED
™ YELLOW
™ GREEN
™ LIGHT BLUE
™ PURPLE
™ BLUE
™ WHITE
▼
Figure 4-4 MARK COLOR window
4. Press the soft key ENTER or the [ENTER]
key.
5. Press the soft key RETURN to finish.
Marks/lines entered hereafter are inscribed
in the shape, color and line type selected
here.
4.3
Changing Mark Size
4.4
Erasing Marks
Mark size can be selected from STD (standard) and SMALL.
Erasing individual marks/lines
1. Press the [MENU] key to display the main
menu.
1. Operate the cursor pad to place the cursor on the mark you want to erase.
2. Press the soft key CHART SETUP OPTIONS.
2. Press the [CLEAR] key. The mark selected is erased.
3. Press the soft key CHART DETAILS to
open the CHART DETAILS menu.
Note: To erase line, place the cursor on
a edge of the line. The line segment will
be erased.
sLAT/LON
GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
OFF
WHITE
STD
DGPS 3D
CHART
DETAIL
EDIT
DEPTH
INFO
RETURN
Figure 4-5 CHART DETAILS menu
4. Press ▼ to select MARK SIZE.
5 Press the soft key EDIT.
Erasing whole marks/lines
You can erase all marks and lines. Be absolutely sure you want to erase all marks and
lines; erased marks and lines cannot be restored.
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
TRACK CONTROL.
2. Press the soft key ERASE MARK. You
are asked if you are sure to erase all
marks and lines.
3. Press the [ENTER] key to erase, or press
the [CLEAR] key to escape.
6. Press ▲ or ▼ to select STD (standard) or
SMALL.
7. Press the [ENTER] key.
4.5
Displaying Track and
Mark Points
Number of track and mark points used appears in the TRACK STATUS window on the
TRACK CONTROL display. For further details see page 3-1.
4-3
This page is intentionally left blank.
5. WAYPOINTS
5.1
Entering Waypoints
In navigation terminology, a waypoint is a particular location on a voyage whether it be a
starting, intermediate or destination point. A
waypoint is the simplest piece of information
your equipment requires to get you to a destination, in the shortest distance possible.
This unit has 835 waypoints (including quick
waypoints) into which you can enter position
information. There are five methods by which
you can enter a waypoint: at own ship’s position, at MOB position, by cursor, by range
and bearing, and through the waypoint list
(manual input of latitude and longitude).
Entering waypoints at own ship’s
position
You can save your current position as a
waypoint. Press the [SAVE/MOB] key with a
touch-and-release action to store your position. This new waypoint will automatically be
saved in the waypoint list under the next consecutive waypoint number.
Entering waypoints at MOB position
The MOB mark functions to mark man overboard position.
2. Press the [ENTER] key to select MOB
position as destination, or the [CLEAR]
key to only mark MOB position.
3. To show range and bearing to the MOB
position, press the soft key NAV L/L followed by the soft key NAV WPT.
Bearing and range
to MOB position
MOB
mark
Range, bearing
Man
overboad
Current
position
Figure 5-2 MOB concept
To erase a MOB mark, you must erase both
the waypoint it is registered under and the
MOB mark itself. Place the cursor on the
MOB mark and press the [CLEAR] key followed by the [ENTER] key to erase the
waypoint. (A flashing diamond appears over
the waypoint when it has been correctly selected.) Repeat to erase the MOB mark.
Entering waypoints by the cursor
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
1. Press the [SAVE/MOB] key several seconds to display the following message.
MAN OVER BOARD!
GO TO (MOB)?
YES ... "ENTER" key
NO ... "CLEAR" key
M
(MOB)
WPT
& ROUTE
WAYPOINTS
ROUTES
LOG
CREATE VOYAGE BASED ROUTE
Figure 5-1 MOB message
DGPS 3D
Figure 5-3 Waypoint & route menu
2. Press the soft key WAYPOINTS to display the waypoint menu.
5-1
ADD/EDIT/MOVE WAYPOINTS
WPT
Changing the shape and color of
waypoint mark
LOCAL LIST
1. Press the soft key SELECT MARK.
ALPHA/NUMERIC LIST
2. Press the soft key MARK SHAPE to open
the mark shape selection window.
WAYPOINT BY CURSOR
WAYPOINT BY RANGE & BEARING
MARK SHAPE
RETURN
DGPS 3D
Figure 5-4 waypoint menu
3. Press the soft key WAYPOINT BY CURSOR. The plotter display appears.
4. Operate the cursor pad to place the cursor on the location desired.
5. Press the soft key NEW WPT. The
waypoint window appears and it shows
mark shape, waypoint name, comment
(default: date), position of waypoint and
proximity alarm radius.
Figure 5-6 Mark shape selection window
MARK
NAME
0 0 1 WPT
COMMENT
17:38 01SEP97
LAT
LON
34 12. 345’ N
135 12. 3457’ W
PROXIMITY
ALARM RADIUS
DGPS 3D
NEW
WPT
SELECT
MARK
COORD
TYPE
N<-->S
E<-->W
SAVE
0.00 nm
3. Operate the cursor pad to select shape
desired.
4. Press the soft key ENTER or the [ENTER]
key.
5. Press the soft key SELECT MARK.
6. Press the soft key MARK COLOR to open
the mark color selection window.
RETURN
SELECT COLOR
Figure 5-5 Waypoint window
6. If you do not need to change the waypoint
data, simply press the soft key SAVE to
register the waypoint and return to the
plotter display. Be sure to press the soft
key SAVE only after changing all data.
▲
' RED
™ YELLOW
™ GREEN
™ LIGHT BLUE
™ PURPLE
™ BLUE
™ WHITE
▼
Figure 5-7 Mark color selection window
7. Press ▲ or ▼ to select the color desired,
and then press the soft key ENTER or the
[ENTER] key.
5-2
Changing waypoint name, comment,
proximity alarm radius
34° 12.345’ N
135° 12.345’ E
FROM
’X’
0.01nm
224.1
WPT
RNG BRG
ZOOM
IN
1. If necessary, you can change the name
(1 to 6 characters), comment (13 characters), L/L position and the proximity alarm
radius (explained in detail in Chapter 8)
as follows:
a) Select the NAME, COMMENT or
PROXIMITY ALARM RADIUS field.
b) Use the cursor pad to select character or digit.
c) Enter appropriate data with the alphanumeric keys.
Note: You cannot change shape and color
of a waypoint when it has a proximity alarm
radius entered. To change shape or color,
enter all zeroes as the proximity alarm radius.
Changing waypoint position
ZOOM
OUT
X
NEW
WPT
START
POINT
DGPS 3D
RETURN
Figure 5-8 Plotter display, Range and
bearing selected as waypoint entry method
4. Operate the cursor pad to place the cursor on the location desired. The range and
bearing from own ship to cursor appear
at the top of the screen.
Note: The origin point of range and
bearing can be shifted to the place you
desire. Operate the cursor pad to select
location, and then press the soft key
START POINT. “X” appears at the cursor
position.
1. Use the cursor pad to place the cursor in
the LAT LON field.
5. Press the soft key NEW WPT. The screen
should look something like the one shown
in Figure 5-5.
2. Operate the cursor pad to place the cursor on digit to change. Enter appropriate
data with the alphanumeric keys.
6. If necessary, change data as you did in
“Entering waypoints by the cursor.”
3. You can switch co-ordinates with the soft
key N<-->S/E<-->W.
Entering waypoints by range and
bearing
This method is useful when you want to enter a waypoint using range and bearing to a
target found on a radar.
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
2. Press the soft key WAYPOINTS to open
the waypoint menu.
7. Press the soft key SAVE to register the
waypoint.
Entering waypoints by latitude and
longitude position
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
2. Press the soft key WAYPOINTS to open
the waypoint menu.
3. Press the soft key LOCAL LIST (lists
waypoints in order from nearest to furthest) or ALPHA/NUMERIC LIST (lists
waypoints in alphanumeric order).
3. Press the soft key WAYPOINT BY
RANGE & BEARING. The plotter screen
appears.
5-3
BRG.
23.8°
1.75nm
FISH01 RNG.
33°12.345' N
ABCDEFGHIJKL
WPT
LOCAL
135°23.456' W
GO TO
WPT001
12:30 29SE97
BRG. 90.0°
RNG. 2.51nm
33°23.456' N
135°23.567' W
BRG.
180.0°
5.07nm
ABCDEF RNG.
34°12.345' N
15:21 01OCT97
135°54.321' W
BRIDGE
BRG. 359.9°
RNG. 8.01nm
34°12.345' N
135°54.321' W
16:45 01OCT97
DGPS 3D
NEW
WPT
EDIT
WPT
BRG.
180.0°
5.07nm
ABCDEF RNG.
34°12.345’ N
15:21 01OCT97
135°54.321’ W
BRIDGE
BRG. 359.9°
RNG. 8.01nm
34°12.345’ N
135°54.321’ W
Erasing waypoints through the
waypoint list
RETURN
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
WPT
ALPHA
GO TO
BRG.
23.8°
1.75nm
FISH01 RNG.
33°12.345’ N
ABCDEFGHIJKL
WPT001
12:30 29SE97
DGPS 3D
135°23.456’ W
BRG. 90.0°
RNG. 2.51nm
33°23.456’ N
135°23.567’ W
4. Press the [ENTER] key. The waypoint is
erased from both the plotter screen and
the waypoint list.
ERASE
WPT
Figure 5-9 Local list
16:45 01OCT97
3. Press the [CLEAR] key. You are asked if
you are sure to erase the waypoint.
NEW
WPT
EDIT
WPT
ERASE
WPT
RETURN
SEARCH FOR _ _ _
Search window
2. Press the soft key WAYPOINTS to open
the waypoint menu.
3. Press the soft key LOCAL LIST or ALPHA/
NUMERIC LIST.
4. Press ▲ or ▼ to select the waypoint you
want to erase.
5. Press the soft key ERASE WPT. You are
asked if you are sure to erase the
waypoint.
6. Press the [ENTER] key. The waypoint is
erased from both the waypoint list and the
plotter screen.
Figure 5-10 Alpha/numeric list
4. Press the soft key NEW WPT to show the
waypoint window. Own ship’s position is
shown. Change the data similar to how
you did in “Entering waypoints by the cursor.”
5. Press the soft key SAVE.
5.2
Erasing Individual
Waypoints
Individual waypoints can be erased by the
cursor or through the waypoint list.
5.3
Changing Waypoint Data
You can change the waypoint data through
the list.
1. Press the [WPT/RTE] key, soft key
WAYPOINTS, and soft key LOCAL LIST
or ALPHA/NUMERIC LIST.
2. Press ▲ or ▼ to select the waypoint you
want to change.
3. Press the soft key EDIT WPT.
4. Change data as you did in “Entering
waypoints by the cursor.”
5. Press the soft key SAVE.
Erasing waypoints by the cursor
1. Press the cursor pad to turn on the cursor.
2. Operate the cursor pad to place the cursor on the waypoint you want to erase. A
flashing diamond mark appears over the
waypoint when it is correctly selected.
5-4
5.4
Waypoint Mark Size
You may change the size of all waypoint
marks to small or large (default), or turn them
off.
3. Operate the cursor pad to place the cursor on the waypoint which you want to
change. A flashing diamond mark appears
on the waypoint when it is correctly selected.
1. Press the [MENU] key to open the main
menu.
4. Press the soft key EDIT/MOVE.
2. Press the soft key CHART SETUP OPTIONS.
6. Operate the cursor pad to place the cursor on the location desired.
3. Press the soft key CHART DETAILS to
open the CHART DETAILS menu.
7. Press the [ENTER] key.
sLAT/LON
GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
OFF
WHITE
STD
DGPS 3D
CHART
DETAIL
EDIT
DEPTH
INFO
The waypoint moves to the cursor position
and its new position is recorded on the
waypoint list. If the waypoint is set as destination or is part of a route, you are asked if
you are sure to move the waypoint. In this
case, press the [ENTER] key again, or the
[CLEAR] key to cancel move.
5.6
RETURN
Figure 5-11 Chart details menu
4. Press ▲ or ▼ to select WAYPOINT.
5. Press the soft key EDIT.
6. Press ▲ or ▼ to select LARGE, SMALL
or OFF. LARGE shows mark in actual
shape. SMALL displays all waypoints with
an “X” regardless of mark shape selected.
7. Press the soft key ENTER or [ENTER]
key.
5.5
5. Press the soft key MOVE WPT.
Changing Waypoint
Position on the Plotter
Display
Searching Waypoints
You can search for a waypoint through the
alpha/numeric list as follows:
1. Press the [WPT/RTE] key, and then press
the soft keys WAYPOINTS and ALPHA/
NUMERIC LIST to show the alpha/numeric list. At the bottom of the display the
search window appears.
SEARCH FOR _ _ _
Figure 5-12 Search window
2. Use the alphanumeric keys to enter the
first 1 - 3 characters in the search window. The waypoint searched appears at
the top of the screen.
You may change the latitude and longitude
position of waypoints on the plotter display
as follows:
1. Press the [WPT/RTE] key followed by the
soft key WAYPOINTS to open the
waypoint menu.
2. Press the soft key WAYPOINT BY CURSOR. The plotter display appears.
5-5
This page is intentionally left blank.
6. ROUTES
Often a trip from one place to another involves
several course changes, requiring a series
of route points (waypoints) which you navigate to, one after another. The sequence of
waypoints leading to the ultimate destination
is called a route. Your unit can automatically
advance to the next waypoint on a route, so
you do not have to change the destination
waypoint repeatedly.
You can store up to 200 routes. A route may
consist of 35 points.
ROUTE NAME
001
COMMENT
NEW
ROUTE
PLOT
LOCAL
LIST
ALPH
LIST
CONECT
ROUTE
DGPS 3D
CANCEL
Figure 6-2 New route entry screen
6.1
Entering Routes
Entering routes through the route
list
This method constructs routes using existing waypoints.
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
2. Press the soft key ROUTES to open the
route menu.
ABCDEF
ABCDEFGHIJKL
BRIDGE
12:30 29SE97
FISH01
15:21 01OCT97
HPT001
16:45 01OCT97
DGPS 3D
LENGTH
25.6 nm
WAYPOINTS
35
LENGTH
56.7 nm
WAYPOINTS
6
LENGTH
21.1 nm
WAYPOINTS
3
LENGTH
4.7 nm
WAYPOINTS
1
SEARCH FOR _ _ _
4. If desired you can change the route name
shown and/or add a comment. To change
route name, press the [CLEAR] key to
clear the route name. Use the cursor pad
to locate the cursor and then press appropriate alphanumeric key. To enter a
comment, place the cursor in the COMMENT window. Use the cursor pad and
alphanumeric keys to enter your comment. A route name may consist of six
characters; comment, 13 characters.
5. Press the soft key LOCAL LIST or ALPH
LIST to open the waypoint list.
GO TO
6. Press ▲ or ▼ to select a waypoint, and
press the soft key ADD WPT to add it to
the route.
NEW
ROUTE
7. Repeat step 6 to complete the route.
ROUTE
EDIT
ROUTE
ERASE
ROUTE
RETURN
RETURN
Figure 6-1 Route menu
When you want to clear a waypoint selected, press the soft key ERASE LST
WP. Each pressing of this key deletes the
last waypoint entered.
8. Press the soft key SAVE to register the
route.
3. Press the soft key NEW ROUTE to open
the new route entry screen.
6-1
Entering routes by the cursor
CONNECT ROUTE
This method allows you to construct a route
directly on the plotter display, using existing
waypoints or new locations. Any new location will be saved as a waypoint, under the
next consecutive waypoint number.
FIRST
SECOND
______
______
FORWARD
REVERSE
NEW
ROUTE
F<-->R
SAVE
1. Follow step 1-4 in “Entering routes
through the route list.”
2. Press the soft key PLOT. The plotter display appears.
DGPS 3D
CANCEL
Figure 6-3 Connect route window
3. Operate the cursor pad to place the cursor on an existing waypoint (soft key ADD
WPT appears) or new location (soft key
ADD NEW WPT appears).
5. Press the soft key F<-->R to select direction to transverse the waypoints of the
route.
4. Press the soft key ADD WP (ADD NEW
WPT) key.
7. Enter the route name of the second route
similar to how you did for the first route.
5. Repeat steps 3 and 4 to complete the
route.
8. Press the soft key SAVE.
6. Press the [ENTER] key to register the
route.
6.2
Connecting Routes
Note: The maximum number of waypoints in
a route is 35. If this number is exceeded an
error message appears. In this case, if desired, delete waypoints in one or both routes
so the total number of waypoints does not
exceed 35.
Two routes can be connected as follows:
1. Press the [WPT/RTE] key followed by the
soft keys ROUTES and NEW ROUTE to
open the new route menu.
2. Enter the name for new route.
3. Press the soft key CONECT ROUTE.
4. Enter the registered route name for the
first route beneath FIRST in the CONNECT ROUTE window.
6.3
Inserting, Removing
Waypoints
Inserting waypoints through the
route list
Waypoints can be inserted in routes as follows:
1. Press the [WPT/RTE] key followed by the
soft key ROUTES to open the route menu.
2. Select a route by pressing ▲ or ▼.
3. Press the soft key EDIT ROUTE. The
route name screen appears.
4. Press the soft key LOCAL LIST. All
waypoints in the route are displayed.
6-2
EDIT
ROUTE
ROUTE NAME: ABCDEF
COMMENT: ABCDEFGHIJKL
s
01
WPT001
02
WPT002
03
WPT003
04
WPT004
05
WPT005
34°12.345’N
135°54.321’W
34°23.456’N
136°10.255’W
35°11.222’N
136°55.889’W
35°22.878’N
136°44.333’W
34°15.279’N
135°34.111’W
LEG
204.8°
33.83nm
22.0°
34.27nm
35.1°
2.89nm
125.6°
31.25nm
INSERT
WPT
REMOVE
WPT
CHANGE
WPT
COORD
TYPE
RETURN
RETURN
DGPS 3D
5. Press ▲ or ▼ to place the cursor at the
location where you want to insert a
waypoint.
6. Press the soft key INSERT WPT to show
the waypoint list.
EDIT
ROUTE
02
LEG
34¡.12.345’N
LOCAL LIST
135¡.54.321’W
204.8¡
WPT01033.83nm
001
34¡.23.456’N
WPT002
136¡.10.255’W
01
WPT001
03
WPT003
04
WPT004
05
WPT005
DGPS 3D
33°22.125’N
136°44.369’W
22.0¡
SELECT
WPT
COORD
TYPE
WPT011
34.27nm
002
35¡.11.222’N
33°22.130’N
136°44.355’W
136¡.55.889’W
35.1¡
LOCAL
LIST
WPT0122.89nm
35¡.22.878’N
003
33°22.111’N
136°44.365’W
136¡.44.333’W
125.6¡
WPT013
34¡.15.279’N
31.25nm
004
33°22.200’N
136°44.113’W
135¡.34.111’W
5. Operate the cursor to place the cursor on
the waypoint which you want to insert.
6. Press the soft key ADD TO START.
7. Operate the cursor pad to place the cursor on an existing waypoint (soft key ADD
WPT appears) or new location (soft key
ADD NEW WPT appears).
8. Press the soft key ADD WPT (ADD NEW
WPT).
Figure 6-4 Edit route menu
ROUTE NAME: ABCDEF
COMMENT: ABCDEFGHIJKL
4. Press the soft key PLOT to show the plotter screen.
ALPH
LIST
RETURN
CANCEL
Figure 6-5 Waypoint list for editing
a route (Local list)
7. Press ▲ or ▼ to select the waypoint you
want to insert. You can switch between
the local list and alphanumeric list by
pressing the soft key LOCAL LIST or
ALPH LIST.
9. Press the [ENTER] key.
When you want to insert waypoints after the
last waypoint, press the soft key “ADD TO
END” at the step 6.
Inserting waypoints in an intermediate
location within a route
1. Follow steps 1 through 4 in “Inserting
waypoints before the first waypoint or after the last waypoint.”
2. Operate the cursor pad to place the cursor on a line connecting waypoints.
3. Press the soft key SPLIT LEG. The selected line turns red.
4. Operate the cursor pad to place the cursor on an existing waypoint (soft key INSERT WPT appears) or new location (soft
key INSERT NEW WPT appears). Press
the appropriate soft key.
Removing waypoints from routes
8. Press the soft key SELECT WPT.
Removing route waypoints through the
route list
Inserting waypoints on the plotter
display
1. Press the [WPT/RTE] key followed by the
soft key ROUTES to open the route menu.
Inserting waypoints before the first
waypoint or after the last waypoint
1. Press the [WPT/RTE] key followed by the
soft key ROUTES to open the route menu.
2. Press ▲ or ▼ to select the route desired.
2. Press ▲ or ▼ to select the route desired.
3. Press the soft keys EDIT ROUTE and
LOCAL LIST to show the waypoint list.
4. Press ▲ or ▼ to select the waypoint you
want to delete.
5. Press the soft key REMOVE WPT.
3. Press the soft key EDIT ROUTE.
6-3
Removing route waypoints from the
plotter display
Next consecutive route number
1. Press the [WPT/RTE] key followed by the
soft key ROUTES to open the route menu.
ROUTE NAME
SAVE
ROUTE
START
LOG
006
2. Press ▲ or ▼ to select the route desired.
COMMENT
3. Press the soft key EDIT ROUTE.
4. Press the soft key PLOT to show the plot
screen.
5. Operate the cursor pad to place the cursor on the waypoint you want to remove
from the route.
6. Press the soft key REMOVE WPT.
6.4
Creating Track-based
Routes
You can create routes based on your ship’s
track by entering waypoints at own ship’s
position. This feature is useful when you wish
to retrace a track.
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
2. Press the soft key CREATE VOYAGE
BASED ROUTE to show the save route
menu.
CANCEL
DGPS 3D
Figure 6-7 New route window
4. If required, you may change the route
name and enter a comment, using the
[CLEAR] key, cursor pad and alphanumeric keys.
5. Press the soft key START LOG to show
the track-based route screen. If you entered an existing route name at step 4,
you are asked if you want to add trackbased waypoints to the existing route.
Then, press the [ENTER] key to select
YES, or the [CLEAR] key to escape.
SAVE
ROUTE
ROUTE NAME: XYZ
COMMENT: BEST FISHING
01
LEG
FINISH
LOG
02
03
ABCDEF
ABCDEFGHIJKL
BRIDGE
12:30 29SE97
FISH01
15:21 01OCT97
HPT001
16:45 01OCT97
DGPS 3D
LENGTH
25.6 nm
WAYPOINTS
35
LENGTH
56.7 nm
WAYPOINTS
6
SAVE
ROUTE
NEW
SEARCH FOR _ _ _
DGPS 3D
COORD
TYPE
RETURN
RETURN
Figure 6-8 Route contents display
RETURN
RETURN
Figure 6-6 Save route menu
3. Press the soft key NEW to show the new
route window.
6-4
05
SELECT
ROUTE
LENGTH
21.1 nm
WAYPOINTS
3
LENGTH
4.7 nm
WAYPOINTS
1
04
6. Press the [PLOT] key to show the plot display. The SAVE icon appears at the bottom of the screen.
NORTH
UP
ZOOM
IN
ZOOM
OUT
COURSE
UP
DGPS 3D
SA
VE
NAV
L/L
SAVE icon
Figure 6-9 SAVE icon appearance
on the plotter display
7. Press the [SAVE/MOB] key with a touchand-release action to enter a waypoint
mark at own ship position. A new waypoint
is created under the next consecutive
waypoint number and that waypoint is
added to the route.
8. Repeat step 7 as necessary. 35 waypoints
can be entered.
9. Press the [WPT/RTE] key followed by the
soft key CREATE VOYAGE BASED
ROUTE.
10.Press the soft key FINISH LOG to register the route. The SAVE icon disappears.
6.5
Erasing Routes
1. Press the [WPT/RTE] key followed by the
soft key ROUTES to open the route menu.
2. Press ▲ or ▼ to select a route you want
to erase.
3. Press the soft key ERASE ROUTE. You
are asked if you are sure to erase the
route.
4. Press the [ENTER] key to erase the route.
6-5
This page is intentionally left blank.
7. NAVIGATION
7.1 Navigating to “Quick
Points”
The “quick point” feature allows you to navigate to point(s) without retaining the data indefinitely in your unit’s memory. Each time a
quick point is entered the previous quick
points having the same quick point numbers
are written over.
Selecting quick point entry method
You need to tell your unit how to set the quick
point: 1 POINT, 35 POINT (up to 35 points)
or WPT/PORT SERV. (For WPT/PORT
SERV, see the next page.)
3. Depending on the selection you made at
step two press the soft key GO TO CURSOR or GO TO WPT.
A light-blue line connects between own ship
and destination, marked “QP<01>”, and it
shows the shortest course to the destination.
Arrows on the line show the direction to follow to the quick point. Range and bearing
from own ship to the destination appears at
the top of screen. This location is saved to
the waypoint list as waypoint “QP01.”
Navigating to multiple quick points
1. Press the [MENU] key.
1. Select 35 POINT in the “selecting quick
point entry method,” and return to the plotter display.
2. Press the soft key DISPLAY OPTIONS.
2. Press the soft key GO TO.
3. Select SET GO TO METHOD and press
the soft key EDIT. The following display
appears.
3. Place the cursor on an existing waypoint
(soft key SELECT WPT appears) or a new
location (soft key ADD QP appears).
SET GO TO METHOD
▲
' 1 POINT
™ 35 POINT
™ WPT/PORT SER
▼
Figure 7-1 Set go to method window
4. Select method desired.
5. Press the soft key ENTER.
6. Press the soft key RETURN to finish.
Navigating to a single quick point
1. Select 1 POINT in the “selecting quick
point entry method,” and return to the plotter display.
2. Place the cursor on an existing waypoint
(soft key GO TO WPT appears) or a new
location (soft key GO TO CURSOR appears).
4. Depending on the selection you made at
step 3 press the soft key SELECT WPT
or ADD QP. “QP<01>” appears at the cursor location. To erase last-entered
waypoint press the soft key ERASE LST
WPT.
5. Repeat steps 3 and 4 to complete.
6. Press the [ENTER] key to register the
route.
A light-blue line connects between own ship
and all quick points, and it shows the shortest course to destination. Arrows on the line
show the direction to follow the route. Quick
points are numbered in sequential order from
QP<01> and are saved to the waypoint list.
Range and bearing from own ship to the first
destination appears at the top of screen. The
unit saves the points as a route, under the
name “Q>RTE” (Quick Route).
7-1
7.2
Navigating to Waypoints
(waypoint list)
1. Press the [WPT/RTE] key to open the
waypoint & route menu.
+ 40°45.971’N
13°57.462’E
4. Select a waypoint.
5. Press the soft key GO TO. The plotter display appears. A light-blue line runs between destination selected and own ship’s
position. Arrows on the line show the direction to the follow. Waypoint data appear at the top of screen.
0.26 nm
180.2°
GO TO
QUICK
ROUTE
NEAR
SRVICE
PUNTA CORNACCHIA
PORT
ACCO AMENO
2. Press the soft key WAYPOINTS to open
the waypoint menu.
3. Press the soft key LOCAL LIST or ALPHA/
NUMERIC LIST to show corresponding
waypoint list.
FROM
OS
ISCHIA PORTO
CASAMICCIOLA
I. ISCHIA
CANCEL
GO TO
DGPS 3D
Figure 7-2 Plotter display
7. Press the soft key PORT or NEAR
SRVICE soft key depending on objective.
PORT shows a list of ports in your area.
NEAR SRVICE displays the port service
list.
SELECT PORT
s
7.3
Navigating to Ports, Port
Services
Some Nav-Charts™ mini chart cards have a
port service list which shows services available at ports or harbors. (See page 2-4.) You
can use the list to set destination as follows:
1. Press the [MENU] key to open the main
menu.
2. Press the soft key DISPLAY OPTIONS.
3. Press ▼ to select SET GO TO METHOD
and press the soft key EDIT. The SET GO
TO METHOD window appears.
4. Press the ▲ or ▼ to select WPT/PORT
SER and press the [ENTER] key or the
soft key ENTER.
ACCIAROLI
ACQUAMORTA
AGNONE S. NICOLA
AGROPOLI
AMALFI
BAIA
CAPRI
CASA MICCIOLA-ISCHIA
Figure 7-3 Sample port list (southern Italy)
SELECT PORT
SERVICE
'
™
™
™
™
™
™
™
5. Press the [PLOT] key to return to the plotter display.
6. Press the soft key GO TO. Soft key titles
change as in Figure 7-2.
▼
Figure 7-4 Sample port service list
7-2
8. If you selected PORT in step 7, use the
cursor pad to select a port and press the
[ENTER] key. Make a route using the soft
keys and press the [ENTER] key. (If you
want to go directly to that port, simply
press the soft key ADD QP followed by
the [ENTER] key.)
FISH
WPT
FROM
OS
1.3 nm
208.5°
ZOOM
IN
ZOOM
OUT
WP-002
GO TO
WPT
FISH
If you selected NEAR SERVICE in step
7, select service mark desired and then
press the soft key ENTER. Then, the display shows the locations of those services
nearest you. (Figure 7-5 shows location
of filling stations in an area in southern
Italy.) Use ▲ or ▼ to place the “hand cursor” on the port service icon desired and
press the soft key ENTER. Make a route
using the soft keys and press the [ENTER] key. (If you want to go directly to
location selected, simply press the soft
key ADD QP followed by the [ENTER]
key.)
+
40°45.971’N
13°57.462’E
FROM
OS
0.26 nm
180.2°
GO TO
GO TO
ROUTE
RVSE
ROUTE
WP-001
DGPS 3D
RETURN
CRAB
Figure 7-6 Plotter display, route
selected as destination
The cursor is on the route waypoint nearest
own ship.
4. Operate the cursor pad to place the cursor on the waypoint or leg desired in the
route.
5. Press the soft key GO TO WPT or FOLLOW LEG (depending on the choice at
step 4).
Green lines connect all route waypoints and
arrows on the lines point in the direction to
traverse the route.
PUNTA CORNACCHIA
ACCO AMENO
ENTER
Navigate route waypoints in reverse
order
ISCHIA PORTO
CASAMICCIOLA
I. ISCHIA
DGPS 3D
CANCEL
GO TO
Figure 7-5 Sample filling station locations
(southern Italy)
Press the soft key RVSE ROUTE to reverse
the order to traverse waypoints. The arrows
on the route line point in direction selected.
Navigate directly to a route
waypoint
7.4
Following a Route
1. Press the [WPT/RTE] key followed by the
soft key ROUTE to open the route list.
If you want to go directly to a route waypoint,
place the cursor on the waypoint to show the
flashing diamond, and then press the soft key
GO TO WPT.
2. Press ▲ or ▼ to select a route.
3. Press the soft key GO TO to show the
plotter display.
Navigate along specific leg of route
Place the cursor on the leg to display it in a
white and red flashing line, and then press
the soft key FOLLOW LEG.
7-3
Restarting navigation
Setting speed for ETA calculation
When you steer to avoid an obstacle or the
vessel drifts, you may go off your intended
course (Line 1 in Figure 7-7). Use the steering or highway display to return to course.
Speed, which may be input manually or automatically, is required to calculate ETA (Estimated Time of Arrival) to a waypoint.
Also, if you don’t need to return to the original course, you can go directly to the waypoint
(Line 2 in Figure 7-7) using the restart function as on the next page.
1. Press the [WPT/RTE] key to display the
waypoint & route menu.
2. Press the soft key LOG.
3. Press the soft key SPEED.
SELECT SPEED
FOR ETA
Line 2
▲
' SPD 10.0kt
™ GPS AVG SPD
▼
Figure 7-9 Select speed for ETA window
Obstacle
4. Key in speed manually in the SPD field,
or use GPS speed data by selecting GPS
AVG SPD.
Line 1
Original course
5. Press the soft key ENTER to register your
selection.
Figure 7-7 Example of when
to restart navigation
1. Set a destination.
Switching waypoints
2. Press the [WPT/RTE] key to open the
waypoint & route menu.
3. Press the soft key LOG.
TO Waypoint (WPT no. in reverse video)
Passed waypoint (gray characters)
Estimated Time of Arrival at last
waypoint
ETA
01
34°23.564’N
135°23.456’E
BRIDGE
02
HARBOR
03
WP<001>
04
WP<002>
05
34°32.456’N
135°32.456’E
34°23.345’N
135°12.456’E
34°34.555’N
135°55.555’E
34°32.555’N
134°99.999’E
WP<003>
LOG
23:59 31.SEP
LEG
120.5°
23.4nm
23.6°
23.4nm
STOP
123.6°
23.5nm
RVSE
ROUTE
180.5°
23.5nm
SPEED
180.5°
23.5nm
DGPS 3D
Figure 7-8 Log display
4. Press the soft key RESTART.
7-4
RESTART
COORD
TYPE
When you arrive to a waypoint on a route,
you can switch to the next waypoint three
ways: AUTO1, AUTO2 and MANUAL.
AUTO1: Automatically switches the TO
waypoint when your boat is within the arrival
alarm area. For how to set the arrival alarm
area, see “8.3 Arrival Alarm” on page 8-1.
AUTO2: Automatically switches the TO
waypoint when the boat enters the arrival
alarm range or the boat passes an imaginary
perpendicular line passing through the center of the destination waypoint.
MANUAL: When the boat enters the arrival
alarm area, the TO waypoint may be switched
by using the soft key RESTART (on the LOG
display). If the arrival alarm is not set, the
waypoint will not be switched. To be alerted
when you arrive at a waypoint turn on the
audio alarm. For further details, see “8.2 Audio Alarm On/Off” on page 8-1.
To select waypoint switching method do the
following:
1. Press the [MENU] key.
2. Press the soft key DISPLAY OPTIONS.
3. Select WAYPOINTS SW.
4. Press the soft key EDIT to show the
waypoint sw window.
5. Select appropriate waypoint switching
method.
7.5
Cancelling Navigation
1. Press the [WPT/RTE] key.
2. Press the soft key LOG.
3. Press the soft key STOP.
4. Press the [ENTER] key to go stand by.
5. Press the soft key RELEASE.
6. Press the [ENTER] key.
6. Press the soft key ENTER to close the
window.
7-5
This page is intentionally left blank.
8. PLOTTER ALARMS
8.1
4. Press ▲ or ▼ to select ON or OFF.
Introduction
There are five plotter-related alarms which
generate both audible and visual alarms: Arrival alarm, Anchor Watch alarm, XTE (Cross
Track Error) alarm, Proximity alarm, and
Speed alarm.
When an alarm setting is violated the buzzer
sounds, and the speaker icon ( ) appears
in red. You may silence the alarm by pressing the [CLEAR] key. The icon remains on
the screen until the cause of the alarm is removed or the alarm is deactivated.
8.2
5. Press the soft key ENTER or the [ENTER]
key to register your selection.
8.3
Arrival Alarm
The arrival alarm informs you that your boat
is approaching a destination waypoint. The
area that defines an arrival zone is that of a
circle which you approach from the outside
of the circle. The alarm will be released if your
boat enters the circle. When the arrival alarm
is active a red dashed circle marks the arrival alarm area.
Audio Alarm On/Off
The audio alarm sounds whenever an alarm
setting is violated. You can enable or disable
the audio alarm as follows:
1. Press the [ALARM] key to show the alarm
menu.
ALARM
ON
ALARM
ON 0.100nm
ARRIVAL ALARM
ON 0.050nm
ANCHOR ALARM
PROXIMITY ALARM ON
ON 0.100nm
XTE ALARM
OVER/UNDER
SPEED ALARM
12.5 ~ 15.0kt
sAUDIO
EDIT
Alarm
range
Own ship
: Alarm area
Destination
waypoint
Figure 8-3 How the arrival alarm works
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select ARRIVAL ALARM.
CLEAR
ALARM
ALARM INFORMATION
3. Press the soft key EDIT to show the arrival alarm window.
NO ALARM
ARRIVAL ALARM
DGPS 3D
▲
Figure 8-1 Alarm menu
' ON 0.500nm
™ OFF
▼
2. Press ▲ or ▼ to select AUDIO ALARM.
3. Press the soft key EDIT to show the audio alarm window.
AUDIO ALARM
▲
ON
™ OFF
▼
'
Figure 8-2 Audio alarm window
Figure 8-4 Arrival alarm window
4. Press ▲ to select ON.
5. Operate the cursor pad to place the cursor on the digit desired.
6. Key in the alarm range desired. The arrival alarm range is 0.001 to 9.999 miles.
7. Press the soft key ENTER or the [ENTER]
key.
8-1
8.4
Anchor Watch Alarm
The anchor watch alarm informs you that your
boat is moving when it should be at rest.
When the anchor watch is active, a red
dashed circle marks the anchor watch area.
8.5
XTE (Cross Track Error)
Alarm
The XTE alarm warns you when your boat is
off its intended course. When the XTE alarm
is active two red dashed lines mark the XTE
alarm area.
Alarm
setting
Your ship’s position
where you start the
anchor watch alarm.
Alarm
setting
Own ship’s
position
Destination
waypoint
: Alarm
area
: Alarm
Figure 8-5 How the anchor
watch alarm works
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select ANCHOR ALARM.
3. Press the soft key EDIT to open the anchor alarm window.
ANCHOR ALARM
▲
' ON 0.050nm
™ OFF
▼
Figure 8-6 Anchor watch alarm window
4. Press ▲ to select ON.
5. Key in the alarm range desired. The anchor watch range is 0.001 to 9.999 miles.
6. Press the soft key ENTER or the [ENTER]
key to register your selection.
8-2
Figure 8-7 How the XTE alarm works
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select XTE ALARM.
3. Press the soft key EDIT to open the XTE
alarm window.
XTE ALARM
▲
' ON 0.100nm
™ OFF
▼
Figure 8-8 XTE alarm window
4. Press ▲ or ▼ to select ON.
5. Key in the alarm range desired. The XTE
alarm range is 0.001 to 9.999 miles.
6. Press the soft key ENTER or the [ENTER]
key to register your selection.
8.6
Speed Alarm
The speed alarm warns when your boat’s
speed is within, over/under or under the
speed range set.
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select SPEED ALARM.
3. Press the soft key EDIT to display the
speed alarm window.
SPEED ALARM
▲
' WITHIN
15.0 ~ 15.3 kt
™ OVER/UNDER
™ OFF
▼
8.7
Proximity Alarm
The proximity alarm alerts you when your
vessels nears a waypoint by the distance set
for that waypoint on the waypoint list. You
can globally activate or deactivate the proximity alarm here. Waypoints whose proximity alarm is active have a ( ) mark near them.
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select PROXIMITY
ALARM.
3. Press the soft key EDIT to show the proximity alarm window.
PROXIMITY ALARM
▲
Figure 8-9 Speed alarm window
4. Press ▲ or ▼ to select WITHIN, OVER/
UNDER, or OFF.
5. Key in the alarm range desired.
6. Press the soft key ENTER or the [ENTER]
key to finish.
' ON
™ OFF
▼
Figure 8-10 Proximity alarm window
4. Select ON or OFF by the cursor pad.
5. Press the soft key ENTER or the [ENTER]
key to register your selection.
8-3
8.8
Alarm messages
Alarm Information
When an alarm setting has been violated the
buzzer sounds and the speaker icon (shown
in red) appears. You can see which alarm
has been violated, as well as silence the
buzzer, on the alarm menu display.
ALARM
ARRIVAL ALARM
ANCHOR ALARM
PROXMTY ALARM
XTE ALARM
SPEED ALARM
ON
ON 0.100nm
ON 0.050nm
ON
ON 0.100nm
OVER/UNDER
12.5 ~ 15.0kt
ALARM INFORMATION
ALARM1
EDIT
CLEAR
ALARM
NEXT
PAGE
Alarm information
(Example: Arrival alarm)
Figure 8-11 Alarm menu
2. Press the soft key CLEAR ALARM to silence the buzzer. The color of alarm message and the speaker icon may change
from red to black.
Note: The speaker icon is displayed in red
until all alarms have been acknowledged on
the alarm menu display. If more than one
alarm has been violated the message CONTINUE appears at the bottom of the display.
In this case press the soft key NEXT INFO to
see which other alarms have been violated.
8-4
YOU'VE ARRIVED AT
WAYPOINT.
Meaning
Arrival alarm setting
violated.
YOU'VE ENTERED AN
AVOIDANCE AREA.
Proximity alarm
setting violated.
YOU HAVE EXCEEDED XTE alarm setting
XTE LIMIT.
violated.
YOU’VE ARRIVED AT
WAYPOINT : SP-001.
DGPS 3D
Message
YOU HAVE EXCEEDED
Anchor watch alarm
ANCHOR WATCH
setting violated.
LIMIT.
1. Press the [ALARM] key.
sAUDIO
Table 8-1 Alarm messages and their meanings
YOU HAVE EXCEEDED Speed alarm setting
SPEED ALARM LIMIT.
violated.
9. SAVING AND LOADING DATA
TO/FROM MEMORY CARD
The following data can be saved to memory
card:
• Mark/line
• Waypoints/routes
• Track
• Configration (menu settings)
9.1
Before you can use a memory card it must
be formatted. Note that formatting a used
card erases all saved data.
1. Insert the memory card you want to format into the slot.
2. Press the [MENU] key followed by the soft
keys CONFIGRATION and UPLOAD/
DOWNLOAD DATA.
MARK/LINE
1. Insert a formatted memory card into the
slot.
2. Press the [MENU] key followed by the soft
keys CONFIGURATION and UPLOAD/
DOWNLOAD DATA.
3. Press the soft key labeled SAVE DATA
TO MEMORY CARD. The SAVE DATA
display (Figure 9-1) appears.
4. Press ▲ or ▼ to select item to save.
SAVE
DATA
OFF
EDIT
5. Press the soft key EDIT to open the
TRACK, MARK/LINE, WAYPOINTS/
ROUTES or CONFIGRATION window.
SAVE
DATA
6. Press ▲ to select ON.
OFF
7. Press the soft key ENTER or the [ENTER]
key.
FORMAT
DGPS 3D
Saving data
OFF
WAYPOINT/ROUTE OFF
CONFIGURATION
Saving Data to Memory
Card
The memory card can save four items of data;
track, mark/line, waypoint/route and configuration.
Formatting Memory Cards
sTRACK
9.2
RETURN
Figure 9-1 SAVE DATA display
3. Press the soft key SAVE DATA TO
MEMORY CARD and the soft key FORMAT. You are asked if you are ready to
format the memory card.
4. Press the [ENTER] key to format (or press
the [CLEAR] key to escape). Now FORMATTING MEMORY CARD appears. Do
not remove the card while it is being formatting. When the formatting is completed, FORMAT COMPLETED appears.
5. Press the [ENTER] key to finish. Now you
can record data to the memory card.
8. Repeat from steps 4 to 7 to save other
data if desired.
9. Press the soft key SAVE DATA. The following message appears and saving
starts. Do not remove the memory card
while data is being saved.
NOW SAVING DATA TO
MEMORY CARD. DO NOT
TURN OFF THE POWER UNTIL
SAVING COMPLETED.
Figure 9-2 SAVE DATA message
When saving is completed, COMPLETE SAVING DATA appears.
10.Press the [ENTER] key.
9-1
Error message
OVERWRITE FOLLOWING
DATA. OK?
(TRACK)
Memory card not inserted
YES ... "ENTER" key
NO ... "CLEAR" key
Press the [ENTER] key to return to the SAVE
DATA display.
MEMORY CARD NOT
INSERTED. INSERT CARD
PRESS "ENTER" key
TO CONTINUE.
Figure 9-3 NOT INSERTED message
Unformatted memory card
Press the [ENTER] key to return to the SAVE
DATA display. And format it refering to the
previous page.
MEMORY CARD NOT
FORMATTED
PRESS "ENTER" key
TO CONTINUE.
Figure 9-4 NOT FORMATTED message
Wrong card inserted
Appears when a chart card is inserted. Press
the [ENTER] key to return to the SAVE DATA
display. Replace it with a formatted memory
card.
WRONG CARD INSERTED.
INSERT MEMORY CARD.
PRESS "ENTER" key
TO CONTINUE.
Figure 9-5 WRONG CARD message
Figure 9-6 OVERWRITE message
9.3
Loading Data from
Memory Card
Data (track, marks, waypoints, configuration)
can be loaded from a memory card and displayed on the screen. This feature is useful
for observing past data and setting up the
equipment for a specific purpose (with “configuration”).
1. Press the [MENU] key followed by the soft
keys CONFIGURATION and UPLOAD/
DOWNLOAD DATA.
2. Press the soft key LOAD DATA FROM
MEMORY CARD to show the LOAD DATA
display.
sTRACK
MARK/LINE
OFF
LOAD
DATA
OFF
EDIT
WAYPOINT/ROUTE OFF
CONFIGURATION
DGPS 3D
LOAD
DATA
OFF
RETURN
Figure 9-7 LOAD DATA display
3. Press ▲ or ▼ to select item to load.
Data overwrite
Data type to be recorded exists on memory
card. (Two or more of same data type cannot be recorded.) Press the [ENTER] key to
overwrite same data type on the card, or
press the [CLEAR] key to escape.
9-2
4. Press the soft key EDIT to show the
ON/OFF selection window.
5. Press ▲ to select ON. Press the soft key
ENTER or the [ENTER] key. If the
memory card does not contain the item
selected, the buzzer sounds and ON cannot be selected.
6. After you select all items desired, press
the soft key LOAD DATA to load data. The
following message appears.
NOW LOADING DATA FROM
MEMORY CARD. DO NOT
TURN OFF THE POWER UNTIL
LOADING COMPLETE.
Figure 9-8 LOAD DATA message
After loading is completed, the following
message appears.
COMPLETE LOADING DATA.
PRESS "ENTER" KEY
TO CONTINUE.
Figure 9-9 COMPLETE message
7. Press the [ENTER] key.
Note on loading data
Track
Since loaded track data is added to internal
track, oldest track will be entered when the
track memory capacity is exceeded.
Waypoint/route
The loaded data substitutes for previously
stored.
Mark/line
The loaded data is added to internal data.
When the mark/line memory becomes full no
marks may be entered.
Configuration
The loaded data replaces current configuration settings. Press the [ENTER] key to restart. If the memory card is ejected while
loading or data could not be loaded, press
the [ENTER] key to restart with default settings. Note that track memory capacity is not
saved or loaded.
9-3
This page is intentionally left blank.
10. CUSTOMIZING YOUR UNIT
This section describes the various options
which allow you to set up your unit to suit
your needs.
10.1 CHART SETUP OPTIONS
menu
The chart offset options menu provides three
menus: chart offset, track control, and chart
details.
1. Press the [MENU] key to open the main
menu.
CHART OFFSET menu
In some instances position may be off by a
few minutes. For example, the position of the
ship is shown to be at sea while it is in fact
moored at a pier. You can compensate for
this error by offsetting chart position as follows:
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
CHART OFFSET.
34° 12.345’ N
135° 12.345’ E
FROM 16.41 nm
276.9°
OS
ZOOM
IN
ZOOM
OUT
2. Press the soft key CHART SETUP OPTIONS.
SET
OFFSET
CHART
SETUP
CHART OFFSET
RESET
OFFSET
DGPS 3D
TRACK CONTROL
CHART
OFFSET
RETURN
Figure 10-2 Plotter display,
chart offset selected
CHART DETAILS
2. Use the cursor pad to place the cursor
where to offset chart position.
DGPS 3D
RETURN
3. Press the soft key SET OFFSET.
Figure 10-1 Chart setup options menu
4. Press the soft key RETURN to finish.
To cancel chart offset, press the soft key RESET OFFSET at step 3 in the above procedure.
TRACK CONTROL menu
This menu mainly controls track color and
track plotting interval. For further details see
Chapter 3.
10-1
CHART DETAILS menu
1. Press the [MENU] key followed by the soft
keys CHART SETUP OPTIONS and
CHART DETAILS.
sLAT/LON
GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
OFF
WHITE
DGPS 3D
CHART
DETAIL
EDIT
DEPTH
INFO
NAV AIDS: Turns aids to navigation symbols
(for example, buoys) on/off. The default setting is ON. When OFF is selected, symbols
are displayed and information is not.
SECTOR INFO: Turns lighthouse viewable
angle indication on FURUNO charts on/off.
Viewing angle is shown as an arc extending
from lighthouse position. Arc color, white or
green, is the color of the light beam. This feature is available with selected charts. The
default setting is ON.
OTHER SYMBOLS: Selects color of all other
chart symbols. The default setting is white.
RETURN
DEPTH INFO soft key: Turns depth info display on/off and sets it color.
Figure 10-3 Chart details menu
2. Use the cursor pad to select item and
press the soft key EDIT.
10.2 DISPLAY OPTIONS menu
3. Select option with cursor pad and press
the soft key RETURN to finish.
This menu contains items for setting up the
plotter display.
Chart details menu description
LAT/LONG GRID: Turns lat/long grid on/off
and changes its color. The default settings
are ON and green.
TEXT INFO: Turns geographic name display
on/off. The default setting is ON.
WAYPOINT: Turns waypoint on or off and selects size to large or small. “LARGE” displays
waypoint in shape selected; “SMALL” shows
waypoints as an X regardless of actual shape.
“OFF” only display waypoints when they are
used in navigation. The default setting is
LARGE.
WAYPOINT NAME: Turns waypoint name
on/off. The default setting is ON.
1. Press the [MENU] key.
2. Press the soft key DISPLAY OPTIONS.
The display setup1 menu appears.
sRNG & BRG MODE
RANGE/SPEED UNIT
DEPTH UNIT
TEMP UNIT
LAT/LON DISPLAY
TIME DISPLAY
WAYPOINTS SW
COURSE VECTOR
BEARING
MAG VARIATION
TD DISPLAY
POSITION DISPLAY
SET GO TO METHOD
RHUMB LINE
nm / kt
m
°C
DD°MM.MMM'
24 HOUR
AUTO2
LINE
MAGNETIC
AUTO 01.3°E
LORAN C
LAT/LON
1 POINT
DGPS 3D
DISPLAY
SETUP
EDIT
RETURN
Figure 10-4 Display setup menu
Display setup menu description
INDEX: Turns chart indices on/off. The default setting is ON.
RNG & BRG MODE
LANDMASS: Selects brightness and color
of landmass. The default settings are bright
and yellow.
The GPS receiver calculates the range, bearing, cross track error (XTE) and ETA to TO
waypoint when you set a destination. The
range and bearing can be calculated by
GREAT CIRCLE (straight line between two
points) or RHUMB LINE (straight line between two points on nautical chart, default
setting) method.
BACKGROUND: Select background color to
black or blue (default setting).
10-2
RANGE/SPEED UNIT
Selects the unit for range and speed; nm/kt
(default setting), km/ km/h, sm/ sm/h.
DEPTH UNIT
You can display your ship’s course and bearing to waypoint in true or magnetic bearing,
and the default setting is magnetic.
MAG VARIATION
TEMP UNIT
The magnetic variations for all areas of the
earth are preprogrammed into this unit. The
preprogrammed variation is accurate for most
instances, however you may wish to manually enter a variation.
Selects unit of water temperature measurement between Celsius or Fahrenheit. The default setting is Fahrenheit.
1. Select MAG VARIATION, and press the
soft key EDIT to show the mag variation
window.
Selects unit of depth measurement among,
feet, fathoms, and meters. The default setting is feet.
LAT/LON DISPLAY
MAG VARIATION
▲
™ AUTO
' MANUAL 0.7°W
▼
Displays the seconds of latitude and longitude positions in hundredths, thousandths
(default setting) or ten thousandths.
TIME DISPLAY
Figure 10-5 Mag variation window
2. Select MANUAL.
Selects time display format for 12 hour or
24 hour (default setting).
3. Key in magnetic deviation value.
WAYPOINT SW
4. Press the soft key W<-->E to switch between East and West and vice versa, if
necessary.
Provides automatic or manual waypoint
switching when following a route. For further
details, see page 7-4. The default setting is
AUTO2.
5. Press the soft key ENTER or the [ENTER]
key to finish.
COURSE VECTOR
Position may be shown in Loran C TDs (default setting), Decca TDs, or latitude and longitude. To display position in TDs select Loran
C or Decca here and choose TD at “POSITION DISPLAY” below. You can select the
Loran C or Decca chain to use on the TD
SETUP menu. For details see “TD SETUP
menu” on page 10-6.
You may extend a line from the own ship position to show ship’s course. The line can be
a vector (the length depends on the ship’s
speed.) or a line (course bar). The default
setting is LINE.
TD DISPLAY
BEARING
POSITION DISPLAY
A navigation device outputs both true and
magnetic bearings. A magnetic bearing is true
bearing plus (or minus) earth’s magnetic deviation. Thus the equation for finding magnetic bearing is;
Displays position in latitude and longitude
(default setting) or Loran C or Decca TDs.
true bearing ± x (magnetic variation)° = magnetic bearing
10-3
SET GO TO METHOD
GPS
OPTION
s LOCAL TIME OFFSET
Selects the method for entering the quick
point: 1 POINT (default setting), 35 POINT
(2-35 points), or WPT/PORT SER. For further details see pages 7-1 and 7-2.
OPERATION MODE
Selects the operation mode between PLEASURE and FISHING.For further details see
page 2-8.
GEODETIC DATUMS
POS SMOOTHING
SPD/CSE SMOOTHING
GPS SPEED AVE
LAT OFFSET
LON OFFSET
DISABLE SATELLITE
LATITUDE
LONGITUDE
ANT. HEIGHT
FIX MODE
+00:00
WGS-84
000 sec
005 sec
060 sec
0.000’N
0.000’E
__ __ __
38°00.000’N
123°00.000’W
005 m
2D/3D
DGPS 3D
EDIT
RETURN
Figure 10-7 GPS SETUP options menu
LOCAL TIME OFFSET
10.3 GPS/DGPS/TD OPTIONS
menu
This menu sets up GPS and DPGS receivers and enables display of position in Loran
C or Decca TDs.
GPS uses UTC time. If you would rather use
local time, enter the time difference between
local time and UTC time. Use the soft key
+<-->- to switch from plus to minus and vice
versa.
GEODETIC DATUM
1. Press the [MENU] key.
DGPS SETUP OPTIONS
The GP-1650D, GP-1650 is preprogrammed
with most of the major chart systems of the
world. Although the WGS-84 system, the
GPS standard, is now widely used other categories of charts still exist. Select the chart
system used, not the area where your boat
is sailing. The default chart system is WGS84.
TD SETUP
1. Select GEODETIC DATUMS.
2. Press the soft key GPS/DGPS/TD OPTIONS to display the GPS/DGPS/TD options menu.
GPS/DGP
OPTION
GPS SETUP OPTIONS
2. Press the soft key EDIT to show the geodetic datum window.
DGPS 3D
RETURN
Figure 10-6 GPS/DGPS/TD options menu
GEODETIC DATUMS
▲
AUSTRALIA
▼
CHART DATUM
GPS SETUP OPTIONS menu
description
This menu provides items for setting up the
GPS receiver. To display it, show the menu
shown in Figure 10-6, and then press the soft
key GPS SETUP OPTIONS.
WGS-84
Figure 10-8 Geodetic datum window
3. Press ▲ or ▼ to select the chart system
you are using. If no chart datum exists for
geodetic datum selected UNKNOWN appears in the CHART DATUM window. In
this case select a different chart system.
4. Press the soft key ENTER or the [ENTER]
key to register your selection.
10-4
POS SMOOTHING
DISABLE SATELLITE
When the DOP or receiving condition is unfavorable, the GPS fix may change greatly,
even if the vessel is dead in water. This
change can be reduced by smoothing the raw
GPS fixes. A setting between 000 to 999 is
available. The higher setting the more
smoothed the raw data, however too high a
setting shows response time to change in
latitude and longitude. This is especially noticeable at high ship’s speeds. 000 is the
normal setting; increase the setting if the GPS
fix changes greatly.
Every GPS satellite is broadcasting abnormal satellite number(s) in it’s Almanac, which
contains general orbital data about all GPS
satellites, including those which are malfunctioning. Using this information, the GPS receiver automatically eliminates any
malfunctioning satellite from the GPS satellite schedule. However, the Almanac sometimes may not contain this information. If you
hear about a malfunctioning satellite from
another source, you can disable it manually.
Enter satellite number (max. 3 satellites) in
two digits and press the soft key ENTER or
the [ENTER] key.
SPD/CSE SMOOTHING
During position fixing, ship’s velocity (speed
and course) is directly measured by receiving GPS satellite signals. The raw velocity
data may change randomly depending on receiving conditions and other factors. You can
reduce this random variation by increasing
the smoothing. Like with latitude and longitude smoothing, the higher the speed and
course smoothing the more smoothed the
raw data. If the setting is too high, however,
the response to speed and course change
slows. For no smoothing, enter all zeroes.
The default setting is 5 (sec).
LATITUDE, LONGITUDE
GPS SPEED AVE
ANT. HEIGHT
Calculation of ETA is based on average ship’s
speed over a given period. If the period is
too long or too short calculation error will result. Change this setting if calculation error
occurs. The default setting is 60 seconds,
which is suitable for most conditions.
Enter the height of the antenna unit above
sea surface. For further details refer to the
installation manual. The default setting is 5
m.
LAT OFFSET, LON OFFSET
You can choose the position-fixing mode from
2D or 2D/3D. 2D requires three satellites to
fix position; 2D/3D requires three or four satellites, whichever is available. The default setting is 2D/3D.
GPS generated position may be off by some
seconds due to GPS signal variation. You
may apply an offset to GPS position to refine
position accuracy.
The default latitude and longitude position is
San Francisco, USA (38.00.00’N,
123.00.000’W). When the unit is turned on
first the first time it begins searching for its
actual position. To lessen the time required
to find position, you may enter your position
manually. To switch from North to South and
vice versa, use the soft key N<-->S, and to
switch from West to East and vice versa, use
the soft key W<-->E. Finally, press the soft
key ENTER or the [ENTER] key.
FIX MODE
10-5
DGPS SETUP OPTIONS menu
TD SETUP menu
This menu sets parameters for the DGPS
beacon receiver. (GP-1650D, or GP-1650
equipped with DGPS beacon receiver.) To
display it, press the [MENU] key followed by
the soft keys GPS/DPGS/TD OPTIONS and
DGPS SETUP OPTIONS.
This menu selects the Loran C or Decca
chain to use to display position in TDs. To
display it, press the [MENU] key followed by
the soft keys GPS/DPGS/TD OPTIONS and
TD SETUP.
DGPS
OPTION
s DGPS
MODE
ON
BEACON FREQUENCY
AUTO
BEACON BAUD RATE
AUTO
DGPS ALARM
OFF
EDIT
TD
LORAN C
s GRI
9940 11-27
U.S. WEST COAST
CORRECTION1
+000.0 s
CORRECTION2
+000.0 s
DECCA
DEC CHAIN
20 R-P
FRENCH
CORRECTION1
+00.00 lane
CORRECTION2
+00.00 lane
DGPS 3D
DGPS 3D
EDIT
RETURN
RETURN
Figure 10-9 DGPS setup options menu
DGPS MODE
Select ON to use the DGPS mode. The default setting is ON. A DGPS beacon receiver
must be connected to use this mode.
BEACON FREQUENCY
DGPS reference station can be searched automatically or manually. For manual search,
select MANUAL here, and use the cursor pad
to select frequency of DGPS reference station. The default setting is AUTO.
BEACON BAUD RATE
Selects the transmission rate of the DGPS
reference station nearest you, among AUTO
(default setting), 50, 100 or 200 bps. This
setting is only effective when the DGPS mode
is “manual”; baud rate cannot be changed in
automatic DGPS mode.
DGPS ALARM
Enable/disable the DGPS alarm. When enabled, the audio alarm sounds three times if
position cannot be found with DGPS. The
default setting is ON.
10-6
SETUP
Figure10-10 TD setup menu
Displaying LORAN C TDs
1. Select GRI and press the soft key EDIT
to show the GRI & sta. pair window.
GRI & STA. PAIR
▲
9940 s 11-27
▼
U.S. WEST COAST
Figure 10-11 GRI & sta. pair window
2. Press ▲ or ▼ to select GRI code. Press
s to enable selection of station pair, and
then press ▲ or ▼ to select station pair.
See the Loran C chain list at the end of
this manual for GRI and station pairs.
3. Press the soft key ENTER or the [ENTER]
key to register your selection.
4. If necessary, you may enter a position offset to refine Loran C position. Select LORAN
C
CORRECTION1
or
CORRECTION2 and press the soft key
EDIT. Enter correction value and press the
soft key ENTER or the [ENTER] key. Use
the soft key + <--> - to switch from plus to
minus and vice versa.
SETUP NMEA PORT 1 menu
description
Displaying DECCA TDs
1. Select DEC CHAIN and press the soft key
EDIT to show the chain sta. pair window.
CHAIN STA. PAIR
▲
20 s P-R
▼
FRENCH
This menu sets up DATA PORT 1 according
to the specifications of the equipment connected to it. The menu can be displayed by
pressing the [MENU] key followed by the soft
keys CONFIGURATION and SETUP NMEA
PORT 1. For detailed information, see the
installation manual.
Figure 10-12 Chain sta. pair window
2. Press ▲ or ▼ to select Decca chain number. Press s to enable selection of lane,
and then press ▲ or ▼ to select lane pair
(R: red, G: green and P: purple). Refer to
the Decca chain list at the end of this
manual.
SETUP
PORT 1
sFORMAT
NMEA0183
Ver2.0
LAT/LON FORMAT DD°MM.MMM’
EDIT
SELECT
SNTNC.
3. Press the soft key ENTER or the [ENTER]
key to register your selection.
4. If necessary, you may enter position offset to refine Decca position. Select
DECCA CORRECTION1 or CORRECTION2 and press the soft key EDIT. Enter correction value and press the soft key
ENTER or the [ENTER] key. Use the soft
key + <--> - to switch from plus to minus
and vice versa.
10.4 CONFIGURATION menu
The configuration menu has facilities for setting up data ports, uploading/downloading
data, self test, demonstration mode setup,
and memory clearing.
DGPS 3D
RETURN
Figure 10-14 Setup NMEA port 1 (or 2) menu
FORMAT
Selects NMEA0183 version 1.5 or 2.0. If you
are unsure of the version of external equipment try both and choose the one which outputs data correctly. The default setting is
version 2.0.
LAT/LON FORMAT (GGA only)
Selects the seconds of latitude and longitude
positions in hundredths, thousandths or ten
thousandths.
1. Press the [MENU] key.
2. Press the soft key CONFIGURATION to
display the configuration menu.
CONFIG
Soft key SELECT SNTNC
This key enables/disables input/output of data
sentences.
SETUP NMEA PORT 1
SETUP NMEA/DGPS PORT 2
UPLOAD/DOWNLOAD DATA
SYSTEM MENU
DGPS 3D
RETURN
Figure 10-13 Configuration menu
10-7
SETUP NMEA/DGPS PORT 2 menu
description
DWNLOAD
UPLOAD
DOWNLOAD WPT/RTE TO PC
This menu should be set according to the
specifications of the equipment connected to
connectors PORT 1 (NMEA) and PORT 2
(DGPS) at the rear of the display unit. The
menu can be displayed by pressing the
[MENU] key followed by the soft keys CONFIGURATION and SETUP NMEA PORT 2.
For detailed information, see the installation
manual.
UPLOAD WPT/RTE FROM PC
SAVE DATA TO MEMORY CARD
LOAD DATA FROM MEMORY CARD
DGPS 3D
RETURN
Figure 10-15 Upload/download menu
FORMAT
Selects data format of connected equipment;
NMEA0183 version 1.5, version 2.0,
RTVM104 (EXTRN), RTCM104 (INTRN) or
RTCM104 (OUTPUT). RTCM104 (INTRN) is
for GP-1850D only. The default setting is
RTVM104 (EXTRN).
The procedure for setting LAT/LON FORMAT
are similar to those for PORT 1. Note that
you cannot setup data sentences when you
select RTCM104 (INTRN) as the format. (A
level converter (IF-1432) is required when
using NMEA0183 format.)
Figure 10-16 Display unit, rear view
LAT/LON FORMAT (GGA only)
Selects the seconds of latitude and longitude
positions in hundredths, thousandths or ten
thousandths.
UPLOAD/DOWNLOAD DATA menu
This menu allows you to upload waypoint and
route data to a PC or download the same
data from a PC, via the DGPS connector at
the back of display unit. The menu can be
displayed by pressing the [MENU] key followed by the soft keys CONFIGURATION
and UPLOAD/DOWNLOAD DATA. For detailed information, see the installation manual.
For memory card, see chapter 9.
Set communication software on the PC as
follows:
Baud Rate:
Character Length:
Stop bit:
Parity:
X Control:
4800 bps
8 bit
1 bit
None
XON/XOFF
The following data can be downloaded/uploaded between a personal computer and this
equipment.
• Waypoint data (In alphanumeric order)
• Route data (In order of route number)
• End of sentence
Note 1: There are two kinds of data for route
data: route data and route comment data.
Note 2: DGPS position fix is not available
when uploading or downloading data.
10-8
Download waypoint/route to PC
Upload waypoint/route from PC
1. Connect the PC to the equipment as
shown below.
Note that all waypoint and route data stored
in your unit will be deleted when data is uploaded.
2. Press the soft key labeled DOWNLOAD
WPT/RTE TO PC. You are asked if you
are ready to download waypoints and
routes.
3. Press the [ENTER] key to download.
1. Connect the PC to the equipment as
shown below.
2. Press the soft key labeled UPLOAD WPT/
RTE FROM PC. You are asked if you are
ready to upload waypoints and routes.
3. Press the [ENTER] key to upload.
GP-1650/1650D
DGPS
1
2
3
4
5
6
7
NC
NC
RD (YELLOW)
NC
SD (RED)
SG (BLUE)
SHIELD
PC/AT
DSUB 9-pin
(EIA-574)
PC/AT
DSUB 25-pin
(EIA-232)
3 (TxD)
2 (TxD)
2
5
4
6
7
8
3 (RxD)
7 (GND)
4 (DTR)
5 (DSR)
6 (RTS)
20 (CTS)
(RxD)
(GND)
(DTR)
(DSR)
(RTS)
(CTS)
Figure 10-17 Connection of GP-1650D/GP-1650 to PC
10-9
Waypoint data format
Route data menu
PFEC, GPwpl, llll.llll, a, yyyyy.yyy, a, c----c, c, c----c, a <CR><LF>
1 2 3
4 5 6 7 8
$GPRTE, x, x, a, ccc, c----c, c----c, ... , c----c <CR><LF>
1 2 3 4 5
6
12
Figure 10-18 Waypoint data format
Figure 10-20 route data format
1: Waypoint latitude
1: Number of sentences required for one
complete route data (1 to 4). See Note 2.
2: N/S
3: Waypoint longitude
2: Number of sentences currently used (1
to 4)
4: E/W
5: Waypoint name (Number of characters is
fixed to 6 and space code is placed when
the number of characters are less than
6.)
6: Waypoint color
7: Waypoint comment (1 byte for mark code
+ 13 characters of comment.)
1st byte of mark code: Fixed to ‘@’.
2nd byte of mark code: Internal mark
code. See Note 1.
8. Information of marking waypoint. Always
set to “A”.
3: Message mode (Always set to C)
4: Route No. (001 to 300, 3 digits required)
5 through 12: Waypoint name (Max. 8
names, length of each waypoint name is fixed
to 7 byte)
Note 2: A route can may contain 35 waypoints
and GPRTE sentence for one route data may
exceed 80 byte limitation. In this case, route
data is divided into several GPRTE sentences
(Max. 4 sentences). This value shows the
number of sentences the route data has been
divided.
Route comment data format
“A”: Displayed
“V”: Not displayed
$PFEC, GPrtc,
Note 1: Following characters can be used
for comments:
xx, c----c <CR><LF>
1
2
Figure 10-21 Route comment format
_ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789&’#
=9
=>
=B
=F
=;
=:
=?
=<
=@
=D
=C
=G
Figure 10-19 Character
available for comment
==
=A
1: Route No. (01 to 200, 3 digits required)
2: Route comment (Max. 16 characters, variable length)
=E
The same characters of the comment for
waypoint comment can be used.
=H
End of sentence
$PFEC, GPxfr,
CTL, E <CR><LF>
Figure 10-22 End of sentence
10-10
SYSTEM menu
This menu provides testing facilities, demonstration mode setup and memory/trip clear.
You may display it by pressing the [MENU]
key followed by the soft keys CONFIGURATION and SYSTEM MENU.
SYSTEM
MENU
SELF TEST
DEMONSTRATION MODE
MEMORY/TRIP CLEAR
DGPS 3D
RETURN
Figure 10-23 System menu
SYSTEM MENU description
SELF TEST, MEMORY/TRIP CLEAR: SELF
TEST and MEMORY/TRIP CLEAR are described in Chapter11.
DEMONSTRATION MODE: This sets the
parameters for the demonstration display. For
further details see page 1-5 .
10-11
This page is intentionally left blank.
11. USING C-MAP NT MODEL
The GP-1650D/1650 C-MAP NT series uses
FURUNO mini chart card and C-MAP NT-FP
chart card. These charts show accurate
coastlines, depth contours, place names, aids
to navigation such as buoys and lighthouses,
and other navigational marks.
11.1 Inserting Chart Card
11.2 Cursor and Data
Display
Besides its fundamental functions of
providing position data, the cursor can also
show caution area, depth area, source of
data, etc. Further, you can display information
about an icon by placing the cursor on it.
1.
Insert an appropriate chart card before
turning on the power.
1.
Press the cursor pad to turn the cursor
on.
34° 12.345' N
135° 12.345' E
FROM 16.45nm
OS
276.9°
NORTH
UP
ZOOM
Push down the lid catch to open the chart
card slot cover.
IN
ZOOM
OUT
COURSE
UP
GO TO
CURSOR
DGPS 3D
Card slot
CENTER
Figure 11-2 Plotter display
Figure 11-1 Location of chart card slot cover
2.
Insert appropriate chart card groove side
up.
3.
Close the slot cover to protect the chart
drive. (Keep the slot cover closed at all
times.)
Note1: Turn off the power before inserting or
ejecting the chart card.
Note2: When using C-MAP NT-FP card, do
not eject it while a chart is being drawn. This
may cause the equipment to stop working.
2.
Use the cursor pad to place the cursor on
the position desired.
3.
Press the [ENTER] key to open the
Objects window. For example the
following window appears.
Objects
Caution area
Depth area
Source of data
Figure 11-3 Objects window
11-1
4.
Press ! or " to select the item desired.
Objects
5.
Press the soft key ENTER or the
[ENTER] key to display details for object
selected Objects.
Navigation mark, fixed
Extended navigational aid, ge
Light
Light
Light
Light
Depth contour
Land area
Source of data
Caution area
Information
LEUCHTFEUER DIE KARTE ENTHAEL
T NUR DIE LAGEN DER WICHTIGEN
FEUER. LIGHTS ONLY THE PRINC
IPAL LIGHTS ARE SHOWN ON THIS
CHART. MISSWEISUNG SIEHE K
ARTEN GROESSEREN MASSSTABS. M
AGNETIC VARIATION LOCAL MAGNE
TIC ANOMALIES SEE LARGER SCAL
E CHARTS.
Figure 11-6 Object windows
3.
Press ! or " to select the item desired.
4.
Press the [ENTER] key to display detailed
information.
Figure 11-4 Example of caution area window
6.
Press the soft key CANCEL to close the
window.
7.
Repeat step 4 to 6 to select other item.
8.
Press the soft key CANCEL to close the
Objects window.
Navigation mark, fixed
Light.
Color
white
Height
7. 00 Meters
Light characteristic
occulting
XXXXXXXX
XXXXXXXX
When you place the cursor on any icon, its
information appears.
1.
Place the cursor on a lighthouse icon.
Figure 11-7 Sample lighthouse data
Place the cursor
on a lighthouse icon.
NAVAID : X X X X X X 6S 7m 9M
FROM OS 2. 43nm
351. 2
5.
NORTH
UP
Press the soft key CANCEL to close the
Objects window.
ZOOM
IN
ZOOM
OUT
COURSE
UP
GO TO
CURSOR
DGPS 3D
CENTER
Figure 11-5 Lighthouse icon
2.
Press the [ENTER] key. For example, the
following window appears.
11.3 Tidal Information
The C-MAP NT-FP chart card provides for
calculation of the tide heights for any date.
Additionally it displays the times of sunrise
and sunset.
1.
Press the cursor pad to place the cursor
on a Tide icon.
T
Figure 11-8 Tide icon
11-2
2.
Press the [ENTER] key to open the
Objects window.
7.
Press the soft key ENTER or the
[ENTER] key to show the tidal graph for
entered date.
8.
Press or to locate the vertical
cursor on the time desired. Time and
height are shown to the left of the graph.
9.
Press or to shift the level cursor.
Draught is shown to the left of the graph.
Objects
Tide height
Depth contour
Caution area
Depth area
Source of data
10. Press the soft key CANCEL to close the
TIDE window.
Figure 11-9 Objects window
11.4 Navigating to Ports,
Port Services
3.
Press or to select Tide height.
4.
Press the soft key ENTER or the
[ENTER] key to open the TIDE window.
Time:
12:00
Height: 1.21 ft
Draught: 0.82 ft
01/01/00 +01
59 26. 467' N
010 28. 646' E
Port Info
HORTEN
High Water (max)
Low Water (min)
Sunrise
09:15L
5.
1.32
1.07
0.82
0.57
0.32
0
4
8
12
16
20
24
1.32 ft (13:15)
0.32 ft (21:45)
Sunset
15:27L
The C-MAP NT-FP chart provides detailed
information on aids to navigation (buoy,
lighthouse) and port service information that
you specify with the cursor. The port service
information includes the availability of water
and fuel supplies, shipyards and first aid, etc.
You can use the list to set destination as
follows:
1.
Press the [MENU] key to open the main
menu.
Figure 11-10 TIDE window
2.
Press the soft key DISPLAY OPTIONS.
Press the soft key DATE to open the
DATE window.
3.
Press to select SET GO TO METHOD
and press the soft key EDIT. The SET
GO TO METHOD window appears.
DATE
SET GO TO METHOD
1 POINT
35 POINT
WPT/PORT SER
DD/MM/YYYY
01 / 01 / 2000
Figure 11-11 DATE window
6.
Use or to position the cursor where
desired and then press the appropriate
numeric keys to enter a date.
Figure 11-12 SET GO TO METHOD window
4.
Press to select WPT/PORT SER and
press the soft key ENTER or the
[ENTER] key.
5.
Press the [PLOT] key once or twice to
return the plotter display.
11-3
6.
Press the soft key GO TO. Soft key titles
change as in Figure 11-10. If GO TO key
is not displayed, press the cursor pad.
+ 40˚45.971'N
13˚57.462'E
FROM
OS
0.26 nm
180.2˚
+
40˚45.971'N
13˚57.462'E
FROM
OS
0.26 nm
180.2˚
GO TO
GO TO
PUNTA CORNACCHIA
ACCO AMENO
QUICK
ROUTE
NEAR
SRVICE
CASAMICCIOLA
PUNTA CORNACCHIA
ACCO AMENO
ENTER
ISCHIA PORTO
DGPS 3D
I.SELECT
ISCHIA ICON BY
KEY.
CANCEL
GO TO
ISCHIA PORTO
Figure 11-15 Sample filling station locations
CASAMICCIOLA
I. ISCHIA
DGPS 3D
CANCEL
GO TO
Figure 11-13 Plotter display
7.
Press the soft key NEAR SRVICE.
The SELECT PORT SERVICE window
appears.
10. Press or to place the “hand cursor”
on the port service icon desired and
press the soft key ENTER or the
[ENTER] key.
+
40˚45.971'N
13˚57.462'E
FROM
QP<01>
0.26 nm
180.2˚
ZOOM
IN
Currently selected icon
SELECT PORT SERVICE
Health emergency
GO TO
ZOOM
OUT
PUNTA CORNACCHIA
ACCO AMENO
ADD
QP
ISCHIA PORTO
CASAMICCIOLA
DGPS 3D
I. ISCHIA
USE
SOFT KEYS TO MAKE
ROUTE THEN PRESS "ENTER"
ERASE
LST QP
CANCEL
GO TO
Figure 11-16 Make route window
Figure 11-14 SELECT PORT SERVICE
window
8.
9.
Use the cursor pad to select service mark
desired. Currently selected icon is
circumscribed. The name of currently
selected icon appears at the top of the
window. Refer to the user’s manual of
C-MAP NT for details about the icons.
Press the soft key ENTER or the
[ENTER] key. Then, the display shows
the locations of those services nearest
you.
11-4
11. Do one of the following:
Go directly to port service selected:
Press the [ENTER] key. The own ship and
the port service is connected by a blue line.
The range and bearing form own ship to
the port service appears at the navigation
data display.
You can go to the port service directly by
steerings the ship to the hearing indicated.
Go to port service selected via
waypoints, make a route as follows:
a) Move the cursor to the nearest waypoint
of the port service.
b) Press the soft key ADD QP.
c) Repeat the above steps a) and b) to
enter other waypoints.
d) Press the [ENTER] key to finish.
A line connects between own ship and
the port service. And the range and
bearing from own ship to first waypoint
appears.
Note: Destination is automatically cancelled if
there is no port for service selected.
11.5 Setting Chart Setup
Options
CHART DETAILS menu
1.
Press the [MENU] key followed by the
soft keys CHART SETUP OPTIONS and
CHART DETAILS.
LAT/LON GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
DGPS 3D
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
ON
WHITE
STD
NAV AIDS: Turns aids to navigation symbols
(for example, buoys) on/off. The default
setting is ON. When OFF is selected,
symbols are displayed but information is not
displayed (at the upper part of the screen).
SECTOR INFO: Turns lighthouse viewable
angle indication on C-MAP NT-FP chart
on/off. Viewing angle is shown as an arc
extending from lighthouse position. This
feature is available with selected charts. The
default setting is ON. When you select OFF,
the visual information is not displayed and the
lighthouse is displayed as “!”.
34° 12.345’ N
135° 12.345’ E
3.
4.
NORTH
UP
ZOOM
IN
ZOOM
OUT
CHART
DETAIL
COURSE
UP
EDIT
GO TO
CURSOR
DEPTH
INFO
CENTER
DGPS 3D
Figure 11-18 SECTOR INFO
RETURN
Lighthouse
34° 12.345’ N
135° 12.345’ E
Figure 11-17 Chart details menu
2.
FROM 16.45nm
OS
276.9°
IN
ZOOM
OUT
COURSE
UP
Select option with cursor pad and press
the soft key ENTER or the [ENTER] key.
Items which are concerned with C-MAP
NT-FP chart card are described here.
LANDMASS: Selects brightness and color of
land. The default settings are bright (BRT)
and yellow. When you select OFF, color of
land is black.
BACKGROUND: When the C-MAP NT-FP
chart card is used, this function is no
inoperative.
NORTH
UP
ZOOM
Press ! or " to select item and press
the soft key EDIT.
Press the soft key RETURN to finish.
FROM 16.45nm
OS
276.9°
GO TO
CURSOR
DGPS 3D
CENTER
Figure 11-19 Lighthouse appearance
when SECTOR INFO is off
OTHER SYMBOLS: Selects color of all other
chart symbols. The default setting is white.
When you select OFF, navaid icons are not
displayed but alarm icons are displayed.
11-5
DEPTH INFO soft key: Turns the DEPTH
INFO display on/off and sets it color in
FURUNO chart, or selects the depth areas
limit and spot sounding & bathymetric range
in C-MAP NT-FP chart.
1.
While displaying chart details menu,
press the soft key DEPTH INFO to show
the following display.
DEPTH
INFO
FOR FURUNO CHART
DEPTH
DEPTH
DEPTH
DEPTH
< 10 m
= 10 m
> 10 m
INFO
RED
YELLOW
LIGHT BLUE
RED
EDIT
Note 1: Depth data depends on the
registered value at "depth area". (See
page 1.)
Note 2: It may be difficult to distinguish
colors of track and mark/line in sea areas
painted in light-blue or green.
SPOT SOUNDING &
BATHYMETRIC RANGE: Sets the depth
range to display the spot sounding on the
C-MAP NT-FP chart. The depth range
you set is displayed red.
10 m : APPROX. 30 ft or 5 fa
FOR C-MAP CHART
11.6 Selecting Chart
Scale/Range
SHADE CHANGE DPTH 0020, 0164 ft
SPOT SOUNDING &
0033~3000 ft
BATHYMETRIC RANGE
DGPS 3D
RETURN
Figure 11-20 DEPTH INFO display
2.
Press or to select item and press
the soft key EDIT or enter the appropriate
value by using numeric keys.
3.
Select option with cursor pad and press
the soft key ENTER or the [ENTER] key.
4.
Press the soft key RETURN several
times to finish.
SHADE CHANGE DPTH: Sets two
values in the range of Depth Limit on the
DEPTH INFO display when the C-MAP
NT-FP chart is used. The Depth Areas
are shown on the screen in three colors
depending on depth.
0 to left value: Blue
left value to right value: Light-blue
greater than right value: Light-gray
(Maximum value: 12000 meter or
39369 ft)
In Figure 11-20, as the following,
0 - 20 ft: Blue
20 - 164 ft: Light-blue
greater than 164 ft: Light-gray
11-6
Chart scale (range) may be selected with the
soft key ZOOM IN or ZOOM OUT. ZOOM IN
expands the chart; ZOOM OUT shrinks it.
The range selected is momentarily displayed
at the lower left-hand corner.
Note: When the display is expanded or
shrunk beyond the range of the chart card in
use the chart is not displayed, and an
appropriate chart icon appears.
11.7 Displaying Program
Number
1.
Press the [MENU] key to open the main
menu.
2.
Press the soft key CONFIGURATION to
show the configuration menu.
3.
Press the soft key SYSTEM MENU to
open the system menu.
4.
Press the soft key SELF TEST to open
the test menu.
5.
Press the soft key MEMORY, I/O TEST to
start the test. Test results and program
numbers. are shown as below.
Program Number
TEST
PROGRAM: OK
No.14518150**
SRAM: OK
INTERNAL
BATTERY: OK
GPS
RECEIVER: OK
No.48502170**
DRAM: OK
PORT1: -- -PORT2: -- --
BEACON
RECEIVER: OK
No.08501820**
No.
RETURN
Figure 11-21 Memory, I/O test results
11-7
This page is intentionally left blank.
12. MAINTENANCE & TROUBLESHOOTING
12.1 Maintenance
Regular maintenance is essential for good
performance. A maintenance program should
be established and should at least include
the items listed in Table 12-1.
WARNING
Do not open the equipment.
Hazardous voltage which can
cause electrical shock, burn or
serious injury exists inside the
equipment. Only qualified
personnel should work inside
the equipment.
Table 12-1 Recommended maintenance program
Item
Antenna
Check point
Check for loosened and corroded
bolts.
Remedy
Tighten loosened bolts. Replace heavily
corroded bolts.
Check connection point for
watertightness.
Antenna cable
Check connector for tightness and
corrosion.
Replace damaged parts.
Check cables for damage.
Display unit
connectors
Check for tight connection.
Tighten loosened connectors.
Ground terminal
Check for tight connection and
corrosion.
Clean or replace as necessary.
Dust and foreign material on the
display unit.
Dust may be removed with a soft cloth. if
necessary anti-static cleaner may be
used. Never use chemical solvents to
clean the display; they can remove paint
and markings.
Dust and foreign material on the
display unit.
Wipe the LCD carefully to prevent
scratching, using tissue paper and an
LCD cleaner. To remove dirt or salt
deposits, use an LCD cleaner, wiping
slowely with tissue paper so as to dissolve
the dirt or salt. Change paper frequently
so the salt or dirt will not scratch the LCD.
Do not use solvents such as thinner,
acetone or benzene for cleaning.
Display unit
LCD
12-1
12.2 Replacement of Fuse,
Battery
The fuse on the power cable protects the
system from reverse polarity of the ship’s
mains and equipment fault. If the fuse blows,
find the cause before replacing it. Use only a
3A fuse. Using the wrong fuse will damage
the unit and void the warranty.
A battery installed on a circuit board inside
display unit preserves data when the power
is turned off. The life of the battery is about
three years. When the battery voltage is low
the battery icon ( ) appears on the display.
When this happens, contact your dealer to
request replacement of the battery.
Lithium
Battery
CAUTION
Type
Code Number
CR2450-F2 ST2
000-133-495
Use the correct fuse.
Use of a wrong fuse can cause fire or
equipment damage.
12.3 Simple Troubleshooting
Below are simple troubleshooting procedures
which the user can follow to restore normal
operation.
Table 12-2 Simple troubleshooting (plotter)
If...
Then...
no picture but marks and characters check if picture advance speed is set to "STOP" on the
appear
sounder setup options menu.
check for loosened transducer connector.
picture appears but no zero line
If using manual video sounder operation, range is shifted; set
shifting to zero to correct.
picture sensitivity is too low
check gain setting, if using manual operation.
marine life or air bubbles may be clinging to transducer face.
water may be dirty.
bottom may be too soft to return a suitable echo.
depth is not displayed
adjust gain to display bottom echo in dark tone.
noise or interference obstructs the
display
check if transducer cable is near ship's engine. If it is,
relocate it.
check ground.
other video sounders may be operating nearby and on same
frequency.
water temperature graph appears
but no or wrong readout
12-2
check for loosened sensor cable.
12.4 Error Messages
SYSTEM
MENU
SELF TEST
This equipment displays the following error
messages on the alarm menu to alert you to
possible trouble.
DEMONSTRATION MODE
MEMORY/TRIP CLEAR
Table 12-4 Error messages
Error Message
Meaning, remedy
NO GPS FIX
No GPS signal.
Check antenna cable.
NO DIFFERENTIAL
GPS CORRECTION.
(GP-1650D only)
No DGPS signal.
Check antenna.
DGPS 3D
RETURN
Figure 12-2 System menu
4. Press the soft key SELF TEST to open
the test menu.
Voltage of internal
VOLTAGE OF
battery is low.
INTERNAL BATTERY IS
Request replacement
LOW.
of battery.
TEST
MEMORY•I/O TEST
KEYBOARD TEST
12.5 Diagnostic Tests
TEST PATTERN
Memory, I/O port test
This test conducts a general check of the display unit and the antenna unit. The unit displays the results for each device or
component checked as OK or NG (No Good).
1. Press the [MENU] key to open the main
menu.
DGPS 3D
RETURN
Figure 12-3 Test menu
5. Press the soft key MEMORY•I/O TEST
to start the test. The test results appears
as below.
2. Press the soft key CONFIGURATION to
show the configuration menu.
TEST
PROGRAM: OK
No.14518010**
CONFIG
SRAM: OK
INTERNAL
BATTERY: OK
GPS
RECEIVER: OK
No.48502170**
SETUP NMEA PORT 1
DRAM: OK
SETUP NMEA/DGPS PORT 2
PORT1: OK
PORT2: OK
BEACON
RECEIVER: OK
No.08501820**
No.
UPLOAD/DOWNLOAD DATA
RETURN
SYSTEM MENU
DGPS 3D
RETURN
: Special connections are required to check these ports.
Otherwise, "--" appears.
**: Program Version No.
Figure 12-1 Configuration menu
Figure 12-4 Memory, I/O test results
3. Press the soft key SYSTEM MENU to
open the system menu.
6. The test runs continuously. To return to
the self test menu, press the soft key
RETURN.
Note: BEACON RECEIVER results only appear on GP-1650D.
12-3
Keyboard test
Display test
This test checks all controls for proper operation.
1. Press the [MENU] key followed by the soft
keys CONFIGURATION, SYSTEM
MENU and SELF TEST to display the self
test menu.
1. Press the [MENU] followed by the soft
keys CONFIGURATION, SYSTEM
MENU and SELF TEST to display the self
test menu.
2. Press the soft key KEYBOARD TEST to
display the screen for testing the keyboard.
2. Press the soft key TEST PATTERN to
open the test pattern display.
3. Press the [ENTER] key to change the test
pattern.
TEST PATTERN
KEYBOAD
TEST
▲
▲
▲
WHT
RED
GRN
BLU
BLK
▲
PRESS
"CLEAR" KEY
3 TIMES
TO RETURN.
PRESS "ENTER" TO CHANGE PATTERN
Figure 12-5 Keyboard test
RETURN
WHT
3. Press any key. The pressed key’s onscreen location turns black if the key is
functioning properly.
4. To escape, press the [CLEAR] key three
times.
RED
GRN
BLU
BLK
Figure 12-6 Display test pattern
12-4
12.6 Clearing Memories
The memory, which stores marks, tracks and
initial settings, can be cleared to start afresh.
When this done all default settings are restored.
1. Press the [MENU] key followed by the soft
keys CONFIGURATION and SYSTEM
MENU.
2. Press the soft key MEMORY/TRIP
CLEAR to open the clear memory menu.
CLEAR
MEMORY
s
CLEAR PLOTTER MEMORY NO
CLEAR GPS MEMORY
NO
CLEAR ALL MEMORY
NO
TRIP METER RESET
NO
DGPS 3D
EDIT
RETURN
Figure 12-7 Clear memory menu
3. Press ▲ or ▼ to select memory/trip to
clear.
4. Press the soft key EDIT.
5. Press ▲ to select YES.
6. Press the soft key ENTER or the [ENTER]
key to clear memory selected.
Note: For PLOTTER MEMORY and CLEAR
ALL MEMORY, all waypoints and routes are
cleared and default settings are restored. If
you require this data, save it to a PC.
12-5
This page is intentionally left blank.
MENU TREE
MENU key
Default settings shown in bold italic.
CHART SETUP OPTIONS
CHART OFFSET
TRACK CONTROL
Default settings shown in bold italic.
CHART DETAILS
Soft key DEPTH INFO
FURUNO chart
DEPTH < 10m (ON, OFF; RED)
DEPTH = 10m (ON, OFF; YELLOW)
DEPTH > 10m (ON, OFF; LIGHT BLUE)
DEPTH INFO (ON, OFF; RED)
(COLORS: RED, YELLOW, GREEN,
LIGHT BLUE, PURPLE, BLUE, WHITE)
C-MAP NT chart
SHADE CHANGE DPTH
SPOT SOUNDING & BATHYMETRIC RANGE
DISPLAY OPTIONS
GPS/DGPS/TD OPTIONS
1
DISPLAY TRACK (ON, OFF)
TRACK COLOR
(RED, YELLOW, GREEN, LIGHTBLUE, PURPLE, BLUE, WHITE)
PLOT (TIME, DISTANCE)
TIME INTERVAL (00m10s)
DIST INTERVAL (00.10nm)
TRACK MAMORY (2000 POINTS)
LAT/LON GRID (ON, OFF; GREEN)
TEXT INFO (ON, OFF)
WAYPOINT (LARGE, SMALL, OFF)
WAYPOINT NAME (ON, OFF)
INDEX (ON, OFF)
LANDMASS (BRT, DIM, OFF; YELLOW)
BACKGROUND (BLACK, BLUE)
NAV AIDS (ON, OFF)
SECTOR INFO (ON, OFF)
OTHER SYMBOLS (ON, OFF; WHITE)
(RED, YELLOW, GREEN, LIGHT BLUE,
PURPLE, BLUE, WHITE)
MARK SIZE (STD, SMALL)
RNG & BRG MODE (GREAT CIRCLE, RHUMB LINE)
RANGE/SPEED UNIT (nm/kt, km/km/h, sm/sm/h)
DEPTH UNIT (m, ft, fa)
TEMP UNIT (°C, °F)
LAT/LON DISPLAY
(DD°MM.MM', DD°MM.MMM', DD°MM.MMMM')
TIME DISPLAY (12HOUR, 24HOUR)
WAYPOINTS SW (AUTO1, AUTO2, MANUAL)
COURSE VECTOR (VECTOR, LINE, OFF)
BEARING (TRUE, MAGNETIC)
MAG VARIATION (AUTO, MANUAL)
TD DISPLAY (LORAN-C, DECCA)
POSITION DISPLAY (LAT/LON, TD)
SET GO TO METHOD
(1POINT, 35POINT, WPT/PORT SERVICE)
OPERATION MODE (PLEASURE, FISHING)
GPS SETUP OPTIONS
LOCAL TIME OFFSET (00:00)
GEODETIC DATUMS (WGS-84)
POS SMOOTHING (000 sec)
SPD/CSE SMOOTHING (005 sec)
GPS SPEED AVE (060 sec)
LAT OFFSET (0.000'N)
LON OFFSET (0.000'E)
DISABLE SATELLITE
LATITUDE (38.00.000'N)
LONGITUDE (123.00.000'W)
ANT. HEIGHT (005m)
FIX MODE (2D, 2D/3D)
DGPS SETUP OPTIONS
DGPS MODE (ON, OFF)
BEACON FREQUENCY
(AUTO, MANUAL)
BAUD RATE
(AUTO, 50, 100, 200)
DGPS ALARM (ON, OFF)
TD SETUP
Loran C Default: 9940, 11-27 (US West Coast)
Decca Default: Chain: 01, R-G (South Baltic)
A-1
LORAN C
(GRI, CORRECTION1, 2)
DECCA
(DEC CHAIN, CORRECTION1, 2)
1
CONFIGURATION
SETUP NMEA PORT 1
FORMAT
(NMEA0183Ver.1.5, 2.0)
LAT/LON FORMAT
(DD°MM.MM’, DD°MM.MMM’, DD°MM.MMMM)
SETUP NMEA/DGPS PORT 2
FORMAT
(NMEA0183Ver.1.5, 2.0, RTCM104EX, RTCM104INTRN,
RTCM104OUT)
LAT/LON FORMAT
(DD°MM.MM’, DD°MM.MMM', DD°MM.MMMM)
SELECT SNTNC. soft key
(AAM, APB, BOD, BWC/BWR, GGA, GLL,
RMA, RMB, RMC, VTG, WPL, XTE, ZDA)
UPLOAD/DOWNLOAD DATA
DOWNLOAD WAYPOINT/RTE TO PC
UPLOAD WAYPOINT/RTE FROM PC
SAVE DATA TO MEMORY CARD
LOAD DATA TO MEMORY CARD
SYSTEM MENU
SELF TEST (MEMORY, I/O; KEYBOARD;TEST PATTERN)
DEMONSTRATION MODE
CLEAR PLOTTER MEMORY (NO, YES)
MEMORY/TRIP CLEAR
CLEAR GPS MEMORY (NO, YES)
CLEAR ALL MEMORY (NO, YES)
TRIP METER RESET (NO, YES)
WPT/RTE key
WAYPOINTS
LOCAL LIST
ALPHA/NUMERIC LIST
WAYPOINT BY CURSOR
WAYPOINT BY RANGE & BEARING
ROUTES
LOG
CREATE VOYAGE BASED ROUTE
ALARM key
AUDIO ALARM (ON, OFF)
ARRIVAL ALARM (ON, OFF)
ANCHOR ALARM (ON, OFF)
PROXIMITY ALARM (ON, OFF)
XTE ALARM (ON, OFF)
SPEED ALARM (WITHIN, OVER/UNDER, OFF)
A-2
Loran C Chains
Chain
GRI
S1
S2
S3
S4
S5
Central Pacific
4990
11
29
–
–
–
Canadian East Coast
5930
11
25
38
–
–
Commando Lion (Korea)
5970
11
31
42
–
–
Canadian West Coast
5990
11
27
41
–
–
South Saudi Arabia
7170
11
26
39
52
–
Labrador Sea
7930
11
26
–
–
–
Eastern Russia
7950
11
30
46
61
–
Gulf of Alaska
7960
11
26
44
–
–
Norwegian Sea
7970
11
26
46
60
–
Southeast USA
7980
11
23
43
59
–
Mediterranean Sea
7990
11
29
47
–
–
Western Russia
8000
10
25
50
65
–
North Central USA
8290
11
27
42
–
–
North Saudi Arabia
8990
11
25
40
56
69
Great Lakes
8970
11
28
44
59
–
South Central USA
9610
11
25
40
52
65
West Coast USA
9940
11
27
40
–
–
Northeast USA
9960
11
25
39
54
–
Northwest Pacific (old)
9970
11
30
55
81
–
Icelandic
9980
11
30
–
–
–
North Pacific
9990
11
29
43
–
–
Suez
4991
10
24
England, France
8940
12
30
Northwest Pacific
8930
11
30
50
70
Newfoundland East Coast
7270
11
25
Lessay
6731
10
39
BØ
7001
11
27
Sylt
7499
11
26
Ejde
9007
10
23
38
Saudia Arabia North
8830
11
25
39
56
Saudia Arabia South
7030
11
25
37
55
A-3
Decca Chains
Chain
No.
Chain
Chain
code
Location
Chain
no.
Chain
Chain
code
Location
01
South Baltic
0A
Europe
34
Kanto
8C
Japan
02
Vestlandet
0E
"
35
Shikoku
4C
"
03
Southwest British
1B
"
36
Hokuriku
2C
"
04
Northumbrian
2A
"
37
Kita Kyushu
7C
"
05
Holland
2E
"
38
Namaqualand
4A
06
North British
3B
"
39
Cape
6A
"
07
Lofoten
3E
"
40
Eastern Province
8A
"
3F
"
41
South West Africa
9C
"
"
08
Southern Africa
09
North Baltic
4B
"
42
Natal
10C
10
North West
4C
"
43
Dampier
8E
11
Trondelag
4E
"
44
Port Headland
4A
12
English
5B
"
45
Anticosti
9C
13
North Bothnian
5F
"
46
East Newfoundland
2C
"
14
Southern Spanish
6A
"
47
Cabot Strait
6B
"
15
North Scottish
6C
"
48
Nova Scotia
7C
"
16
Gulf of Finland
6E
"
17
Danish
7B
"
18
Irish
7D
"
19
Finnmark
7E
"
20
French
8B
"
21
South Bothnian
8C
"
22
Hebridean
8E
"
23
Frisian Islands
9B
"
24
Helgeland
9E
"
25
Skagerrak
10B
"
26
North Persian Gulf
5C
27
South Persian Gulf
1C
"
28
Bombay
7B
"
29
Calcutta
8B
"
30
Bangladesh
6C
"
31
Saliyah
2F
"
32
Hokkaido
9C
Japan
33
Tohoku
6C
"
Persian Gulf & India
A-4
Australia
"
Northern America
World Time
A-5
Geodetic Chart List
001:
002:
003:
004:
005:
006:
007:
008:
009:
010:
011
012:
013:
014:
015:
016:
017:
018:
019:
020:
021:
022:
023:
024:
025:
026:
027:
028:
029:
030:
031:
032:
033:
034:
035:
036:
037:
038:
039:
040:
041:
042:
043:
044:
045:
046:
047:
048:
049:
050:
051:
052
053:
054:
055:
056:
057:
058:
059:
060:
061:
062:
063:
064:
065:
066:
067:
068:
069:
070:
071:
072:
073:
074:
075:
076:
077:
078:
079:
080:
081:
082:
083:
084:
085:
086:
087:
088:
089:
090:
091:
092:
093:
WGS84
WGS72
TOKYO
NORTH AMERICAN 1927
EUROPEAN 1950
AUSTRALIAN GEODETIC 1984
ADINDAN-MN
ADINDAN-E
ADINDAN-MA
ADINDAN-SE
ADINDAN-SU
AFG
AIN EL ABD 1970
ANNA 1 ASTRO 1965
ARC 1950-MN
ARC 1950-B
ARC 1950-L
ARC 1950-M
ARC 1950-S
ARC 1950-ZR
ARC 1950-ZM
ARC 1950-ZB
ARC 1960-MN
ARC 1960-K
ARC 1960-T
ASCENSION IS. 1958
ASTRO BEACON “E”
ASTRO B4 SOR. ATOLL
ASTRO POS 71/4
ASTRONOMIC STATION 1952
AUSTRALIAN GEODETIC 1966
BELLEVUE (IGN)
BERMUDA 1957
BOGOTA OBSERVATORY
GAUPO INCHAUSPE
CANTON IS. 1966
CAPE
CAPE CANAVERAL
CARTHAGE
CHATHAM 1971
CHUA ASTRO
CORREGO ALEGRE
DJAKARTA (BATAVIA)
DOS 1968
EASTER IS. 1967
EUROPEAN 1950-WE
EUROPEAN 1950-CY
EUROPEAN 1950-EG
EUROPEAN 1950-ESC
EUROPEAN 1950-EIS
EUROPEAN 1950-GR
EUROPEAN 1950-IR
EUROPEAN 1950-SA
EUROPEAN 1950-SI
EUROPEAN 1950-NF
EUROPEAN 1950-PS
EUROPEAN 1979
GANDAJIKA BASE
GEODETIC DATUM 1949
GUAM 1963
GUX 1 ASTRO
HJORSEY 1955
HONG KONG 1363
INDIAN-TV
INDIAN-BIN
IRELAND 1965
ISTS 073 ASTRO 1969
JOHNSTON IS. 1961
KANDAWALA
KERGUELEN IS.
KERTAU 1948
LA REUNION
L. C. 5 ASTRO
LIBERIA 1964
LUZON
LUZON-M
MAHE 1971
MARCO ASTRO
MASSAWA
MERCHICH
MIDWAY ASTRO 1961
MINNA
NAHRWAN-O
NAHRWAN-UAE
NAHRWAN-SA
NAMIBIA
MAPARIMA, BWI
NORTH AMERICAN 1927WU
NORTH AMERICAN 1927EU
NORTH AMERICAN 1927AK
NORTH AMERICAN 1927BH
NORTH AMERICAN 1927SS
NORTH AMERICAN 1927CN
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
094:
095:
096:
097:
098:
099:
100:
101:
102:
103:
104:
105:
106:
107:
108:
109:
110:
111:
112:
113:
114:
115:
116:
117:
118:
119:
Mean Value (Japan, Korea & Okinawa)
Mean Value (CONUS)
Mean Value
Australia & Tasmania
Mean Value (Ethiopia & Sudan)
Ethiopia
Mali
Senegal
Sudan
Somalia
Bahrain Is.
Cocos Is.
Mean Value
Botswana
Lesotho
Malawi
Swaziland
Zaire
Zambia
Zimbabwe
Mean Value (Kenya & Tanzania)
Kenya
Tanzania
Ascension Is.
Iwo Jima Is.
Tern Is.
St. Helena Is.
Marcus Is.
Australia & Tasmania
Efate & Erromango Islands
Bermuda Islands
Columbia
Argentina
Phoenix Islands
South Africa
Mean Value (Florida & Bahama Islands)
Tunisia
Chatham Is. (New Zealand)
Paraguay
Brazil
Sumatra Is. (Indonesia)
Gizo Is. (New Georgia Is.)
Easter Is.
Western Europe
Cyprus
Egypt
England, Scotland, Channel & Shetland Islands
England, Ireland, Scotland, & Shetland Islands
Greece
Iran
Italy, Sardinia
Italy, Sicily
Norway & Finland
Portugal & Spain
Mean Value
Republic of Maldives
New Zealand
Guam Is.
Guadalcanal Is.
Iceland
Hong Kong
Thailand & Vietnam
Bangladesh, India & Nepal
Ireland
Diego Garcia
Johnston Is.
Sri Lanka
Kerguelen Is.
West Malaysia & Singapore
Mascarene Is.
Cayman Brac Is.
Liberia
Philippines (excl. Mindanao Is.)
Mindanao Is.
Mahe Is.
Salvage Islands
Eritrea (Ethiopia)
Morocco
Midway Is.
Nigeria
Masirah Is. (0man)
United Arab Emirates
Saudi Arabia
Namibia
Trinidad & Tobago
Western United States
Eastern United States
Alaska
Bahamas (excl. San Salvador Is.)
Bahamas, San Salvador Is.
Canada (incl. Newfoundland Is.)
120:
121:
122:
123:
124:
125:
126:
127:
128:
129:
130:
131:
132:
133:
134:
135:
136:
137:
138:
139:
140:
141:
142:
143:
144:
145:
146:
147:
148:
149:
150:
151:
152:
153:
154:
155:
156:
157:
158:
159:
160:
161:
162:
163:
164:
165:
166:
167:
168:
169:
170:
171:
172:
173:
A-6
NORTH AMERICAN 1927AB
: Alberta & British Columbia
NORTH AMERICAN 1927EC
: East Canada
NORTH AMERICAN 1927MO
: Manitoba & Ontario
NORTH AMERICAN 1927NE
: Northwest Territories & Saskatchewan
NORTH AMERICAN 1927YK
: Yukon
NORTH AMERICAN 1927CZ
: Canal Zone
NORTH AMERICAN 1927CR
: Caribbean
NORTH AMERICAN 1927CA
: Central America
NORTH AMERICAN 1927CU
: Cuba
NORTH AMERICAN 1927GR
: Greenland
NORTH AMERICAN 1927MX
: Mexico
NORTH AMERICAN 1983AK
: Alaska
NORTH AMERICAN 1983CN
: Canada
NORTH AMERICAN 1983CS
: CONUS
NORTH AMERICAN 1983MX
: Mexico, Central America
OBSERVATORIO 1966
: Corvo & Flores Islands (Azores)
OLD EGYPTIAN 1930
: Egypt
OLD HAWAIIAN-MN
: Mean Value
OLD HAWAIIAN-HW
: Hawaii
OLD HAWAIIAN-KA
: Kauai
OLD HAWAIIAN-MA
: Maui
OLD HAWAIIAN-OA
: Oahu
OMAN
: Oman
ORDNANCE SURVEY OF GREAT BRITAIN 1936-MN: Mean Value
ORDNANCE SURVEY OF GREAT BRITAIN 1936-E: England
ORDNANCE SURVEY OF GREAT BRITAIN 1936-IM: England, Isle
of Man & Wales
ORDNANCE SURVEY OF GREAT BRITAIN 1936-SSI: Scotland, &
Shetland Islands
ORDNANCE SURVEY OF GREAT BRITAIN 1936-WL: Wales
PICO DE LAS NIVIES
: Canary Islands
PITCAIRN ASTRO 1967
: Pitcairn Is.
PROVISIONS SOUTH CHILEAN 1963: South Chile (near 53˚ S)
PROVISIONAL SOUTH AMERICAN 1956MN: Mean Value
PROVISIONAL SOUTH AMERICAN 1956BO: Bolivia
PROVISIONAL SOUTH AMERICAN 1956NC: Chile-Northern Chile
(near 19˚S)
PROVISIONAL SOUTH AMERICAN 1956SC: Chile-Southern Chile
(near 43˚S)
PROVISIONAL SOUTH AMERICAN 1956CO: Columbia
PROVISIONAL SOUTH AMERICAN 1956EC: Ecuador
PROVISIONAL SOUTH AMERICAN 1956GY: Guyana
PROVISIONAL SOUTH AMERICAN 1956PR: Peru
PROVISIONAL SOUTH AMERICAN 1956VN: Venezuela
PUERTO RICO
: Puerto Rico & Virgin Islands
QATAR NATIONAL
: Qatar
QORNOQ
: South Greenland
ROME 1940
: Sardinia Islands
SANTA BRAZ
: Sao Maguel, Santa Maria Islands (Azores)
SANTO (DOS)
: Espirito Santo Is.
SAPPER HILL 1943
: East Falkland Is.
SOUTH AMERICAN 1969MN
: Mean Value
SOUTH AMERICAN 1969AG
: Argentina
SOUTH AMERICAN 1969BO
: Bolivia
SOUTH AMERICAN 1969BR
: Brazil
SOUTH AMERICAN 1969CH
: Chile
SOUTH AMERICAN 1969CO
: Columbia
SOUTH AMERICAN 1969EC
: Ecuador
SOUTH AMERICAN 1969GY
: Guyana
SOUTH AMERICAN 1969PA
: Paraguay
SOUTH AMERICAN 1969PR
: Peru
SOUTH AMERICAN 1969TT
: Trinidad & Tobago
SOUTH AMERICAN 1969VZ
: Venezuela
SOUTH ASIA
: Singapore
SOUTHEAST BASE
: Porto Santo & Madeira Islands
SOUTHWEST BASE
: Faial, Graciosa, Pico, Sao Jorge, & Terceira Is.
TIMBALAI 1948
: Brunei & East Malaysia (Sarawak & Sadah)
TOKYO JP
: Japan
TOKYO KP
: Korea
TOKYO OK
: Okinawa
TRISTAN ASTRO 1968
: Tristan da Cunha
VITI LEVU 1916
: Viti Levu Is. (Fiji Islands)
WAKE-ENIWETOK 1960
: Marshall Islands
ZANDERIJ
: Surinam
BUKIT RIMPAH
: Bangka & Belitung Islands (Indonesia)
CAMP AREA ASTRO
: Camp Mcmurdo Area, Antarctica
G. SEGARA
: Kalimantan Is. (Indonesia)
HERAT NORTH
: Afghanistan
HU-TZU-SHAN
: Taiwan
TANANARIVE OBSERVATORY 1925: Madagascar
YACARE
: Uruguay
RT-90
: Sweden
Pulkovo 1942
: Russia
Finish KKJ
: Finland
SPECIFICATIONS OF
COLOR GPS/ PLOTTER: GP-1650
COLOR DGPS/ PLOTTER: GP-1650D
1. GENERAL
(1) Display
5.6 inch high resolution color LCD
(2) Projection
Mercator
(3) Usable Area
85° latitude or below
(4) Display Mode
Plotter, Video pilot, Highway display, Waypoint display
2. GPS RECEIVER
(1) Receiving Channels
12 channels, 12 satellite tracking, Parallel tracking
(2) Rx Frequency
1575.42 MHz
(3) Rx Code
C/A code
(4) Position Fixing System
All in view, 8-state Kalman filter
(5) Position Accuracy
Approx. 10 m, 95% of the time,
horizontal dilution of position(HDOP)≤1
Note: All GPS receiver are subject to degradation of position and
velocity accuracy under the U.S. Department of Defense.
Position may be degraded.
DGPS: Approx. less than 5 m, 95% of the time
(6) Tracking Velocity
900 kts
(7) Position-fixing Time
Warm start: 12 seconds, Cold start: 90 seconds
(8) Position Update Interval
1 second
(9) DGPS Data Receiving
RTCM SC-104 Ver 2.1 formatted
(External DGPS data required for GP-1650)
3. DISPLAY SECTION
(1) Effective area
115.2×84.2 mm
(2) Display pixels
234×320 dots
(3) Position Indication
Latitude/longitude or Loran C LOP or DECCA LOP
4. PLOTTER
(1) Effective Projection Area 0.125 nm to 2,048 nm (at equatorial area)
(2) Track Display
Plot interval: by time (0 to 99 min. 59 sec.) or
by distance (0 to 99.99 nm)
(3) Colors
Red, yellow, green , purple, light-blue, blue, white
(4) Memory Capacity
Track/Mark: 5000 points, waypoint: 800 point
(5) Storage Capacity
Simple route: 200 routes with 35 waypoints each
SP - 1
(6) MOB
1 point
(7) Quick routes
1 course
(8) Electronic Chart
FURUNO chart card or NAVIONICS chart card available
C-MAP chart card also available for C-MAP NT Model
5. DATA INPUT / OUTPUT
(1) Input data
IEC61162-1 adopted
$**DBT, $**DPT, $**MTW, $**TLL, $GPWPL
(2) Output data
IEC61162-1 adopted
$GPAAM, $GPAPB, $GPBOD, $GPBWR/GPBWC, $GPGLL,
$GPGGA, $GPRMA, $GPRMB, $GPRMC, $GPVTG, $GPXTE,
$GPZDA, $GPWPL
6. POWER SOURCE
(1) For DC Source
12-24 VDC (-10%,+30%): 1.2-0.6 A
(2) For AC Source
100/110/115/200/220/230 VAC, 1 phase, 50/60 Hz
(optional rectifier required)
7. ENVIRONMENTAL CONDITIONS
(1) Useable Temperature
Antenna unit: -25ºC to + 70ºC
Display unit: -15ºC to +55ºC
(2) Relative Humidity
95%(40ºC)
(3) Waterproofing
Antenna unit: IEC60529 IPX6
Display unit: IEC60529 IPX5
8. COATING COLOR
(1) Display Unit
Cover: Munsell 2.5GY5/1.5
Panel: N3.0
(2) Antenna Unit
N9.5
SP - 2
INDEX
A
Alarm information window 8-4
Alarm messages 8-4
Alarms
alarm information window 8-4
alarm message 8-4
anchor watch alarm 8-2
arrival alarm 8-1
audio alarm 8-1
DGPS alarm 10-6
proximity alarm 8-3
speed alarm 8-3
XTE alarm 8-2
Anchor watch alarm 8-2
Antenna height 10-5
Arrival alarm 8-1
Audio alarm 8-1
Auto course-up mode 2-1
B
Background color
chart 10-2
Battery replacement 12-2
Beacon baud rate 10-6
Beacon frequency 10-6
Beacon information display 2-6
Brilliance adjustment 1-3
Buoy data 2-4
C
Chart details menu 10-2
Chart offset menu 10-1
Chart scale 2-2
Chart setup options menu 10-1–10-2
Configuration menu 10-7–10-11
Course vector 10-3
Course-up mode 2-1
Cross-track error alarm. See XTE alarm
Cursor 2-2
Cursor data 11-1
D
Decca chains A-4
DECCA station selection 10-6
Demonstration display 1-5
Depth info 10-2
DEPTH INFO soft key 10-2
Depth unit 10-3
DGPS alarm 10-6
DGPS beacon information display 2-6
DGPS mode 10-6
DGPS setup options mode 10-5–10-7
Diagnostics
display test 12-4
keyboard test 12-4
memory, I/O test 12-3
remote controller test 11-5
Disable satellite 10-5
Display options menu 10-2–10-4
Display setup menu 10-2–10-4
Display test 11-4
Downloading data 10-9
E
Error messages 12--3
F
Fix mode 10-5
Fuse replacement 12-2
G
Geodetic datum 10-4
GPS position offset 10-5
GPS satellite monitor display 2-5
GPS/DGPS/TD options menu 10-4–10-7
Great circle 10-2
Grid 10-2
H
Highway display 2-7
I
Indications
enlargement of nav data 2-5
K
Keyboard test 12-4
L
Lat/lon display resolution 10-3
Lighthouse data 2-4
Local time 10-4
Loran C chains A-3
Loran C station selection 10-6
M
Magnetic bearing 10-3
Magnetic variation 10-3
Maintenance 12-1
Mark
color 4-2
displaying 4-2
entering 4-1
erasing 4-3
line 4-2
shape 4-2
Index-1
Memory card
formatting 9-1
saving data 9-1
loading 9-2
Memory/trip clear 12-5
Memory, I/O port test 12-3
MENU key 1-4
Menu tree A-1–A-2
Mini chart cards
aids to navigation data 2-4
background color 10-2
buoy data 2-4
chart scale 2-2
chart symbol color 10-2
chart symbols 2-3
depth info 10-2
grid 10-2
Indices 10-2
indices 2-3
inserting 1-2
landmass color 10-2
lighthouse data 2-4
nav aids 10-2
port service icons (NAVIONICS) 2-4
text info 10-2
N
Nav data display 2-5
Navigation
cancelling 7-5
multiple quick points 7-1
ports, port service 7-2
quick points 7-1–7-5
restarting 7-4
route 7-3
route in reverse order 7-3
single quick point 7-1
specific route leg 7-3
switching route waypoints 7-4
waypoints 7-2
North-up mode 2-1
Q
Quick points
entry method 7-1
multiple points 7-1
single point 7-1
R
Range selection
plotter 2-2
Range unit 10-3
Rhumb line 10-2
Routes
connecting (two) 6-2
entering by cursor 6-2
entering through route list 6-1
entering track based 6-4
erasing 6-5
inserting waypoints on the plotter display 6-3
inserting waypoints through route list 6-2
navigating 7-3
navigating in reverse order 7-3
navigating specific leg 7-3
removing from plotter display 6-4
removing waypoints through route list 6-3
restarting navigation of 7-4
switching waypoints 7-4
S
Object 11-1
Operation mode 2-8
SAVE/MOB key 5-1
Sector info (lighthouse viewable angle) 10-2
Setup NMEA port 1 menu 10-7
Setup NMEA port 2 menu 10-8
Smoothing
position 10-4
speed/course 10-5
Soft keys 1-4
Speed
GPS speed averaging 10-5
input 7-4
unit 10-3
Speed alarm 8-3
Steering display 2-6
System configuration v
System menu 10-11
P
T
Port services
description 2-4
navigating to 7-2,11-3
Position format selection 10-3
Position input 10-5
Power on/off 1-2
POWER/BRILL key 1-3
Presentation modes 2-1
Program number 11-7,12-3
Proximity alarm 8-3
activating, deactivating 8-3
setting radius for individual waypoints 5-3
TD setup menu 10-6–10-7
TDs selection 10-3
Temperature unit 10-3
Tidal Information 11-2
Time
display selection 10-3
local 10-4
Trip 2-8
Tone adjustment 1-3
O
Index-2
Track
color 3-2
displaying 3-1
erasing all 3-3
plotting interval 3-2
stopping/restarting plotting of 3-1
Track based route 6-4
Track and markpoints 4-2
Troubleshooting 12-2
U
Upload/download data menu 10-8
Uploading data 10-9
W
Waypoints
changing data 5-4
changing position at entry 5-3
changing position on plotter screen 5-5
color 5-2
comments 5-3
entering at MOB position 5-1
entering at own ship's position 5-1
entering by cursor 5-1
entering by latitude and longitude position 5-3
entering by range and bearing 5-3
erasing individual by cursor 5-4
erasing individual through waypoint list 5-4
mark size 5-5
name entry 5-3
name on/off 10-2
navigating by 7-2
proximity alarm radius 5-3
searching 5-5
shape 5-2
size 10-2
World time A-5
WPT/RTE key 5-1
X
XTE alarm 8-2
XTE scale 2-7
Index-3
Download PDF

advertising