Furuno GP-1650WD GPS Receiver User Manual

Back
COLOR DGPS/PLOTTER
COLOR GPS/PLOTTER
GP-1650WD, GP-1650W FURUNO/NAVIONICS
GP-1650WD, GP-1650W FURUNO/C-MAP NT
The paper used in this manual
is elemental chlorine free.
Your Local Agent/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone :
0798-65-2111
Fax
0798-65-4200
:
All rights reserved.
Printed in Japan
FIRST EDITION : AUG
AUG.. 2002
B1
Pub. No. OME-44240
( TATA ) GP-1650W/1650WD
: APR
APR.. 12, 2005
*00080935700*
*00080935700*
*00080935700*
*OME44240B10*
*OME44240B10*
*OME44240B10*
SAFETY INSTRUCTIONS
WARNING
CAUTION
Do not use the equipment for other than
its intended purpose.
Do not open the equipment.
Hazardous voltage which can cause
electrical shock, burn or serious injury
exists inside the equipment. Only qualified
personnel should work inside the equipment.
No one navigation device should ever be
solely replied upon for the navigation of
a vessel.
Do not disassemble or modify the
equipment.
Always confirm position against all available
aids to navigation, for safety of vessel and
crew.
Fire, electrical shock or serious injury
can result.
Use the proper gain setting.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Incorrect gain may produce wrong depth
indication, possibly result ing in a
dangerous situation. See "Adjusting the
gain" on page 2-6.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
The picture is not refreshed when
picture advancement is stopped.
Do not operate the equipment with wet
hands.
Maneuvering the vessel in this condition
may result in a dangerous situation.
Electrical shock can result.
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or illegible, contact
a FURUNO agent or dealer.
Use the proper fuse.
Fuse rating is shown on the power cable.
Use of a wrong fuse can result in damage
to the equipment.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
About the TFT LCD
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.01%
of the pixels may drop out or blink, however this is not an indication of malfunction.
i
Name: Warning Label (1)
Type: 86-003-1011-1
Code No.: 100-236-231
TABLE OF CONTENTS
4.5
4.6
Displaying Track and Mark
Points ............................................ 4-4
Target Mark ................................... 4-4
5.
WAYPOINTS
5.1
5.2
5.3
5.4
5.5
5.6
Entering Waypoints ....................... 5-1
Erasing Individual Waypoints......... 5-4
Changing Waypoint Data............... 5-5
Changing Waypoint Position on
the Plotter Display ......................... 5-5
Waypoint Mark Size....................... 5-6
Searching Waypoints..................... 5-6
6.
ROUTES
6.1
6.2
6.3
6.4
6.5
Entering Routes............................. 6-1
Connecting Routes........................ 6-2
Inserting, Removing Waypoints ..... 6-3
Creating Track-based Routes........ 6-5
Erasing Routes.............................. 6-6
FOREWORD .................................. iv
SYSTEM CONFIGURATION ......... v
WHAT IS WAAS?........................... vi
1.
OPERATIONAL OVERVIEW
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Display Unit Controls .....................1-1
Inserting Mini Chart Card ...............1-2
Turning the Power On/Off ..............1-2
Adjusting Tone and Brilliance .........1-3
Plotter Displays..............................1-4
Steering/Highway Displays ............1-4
Menu Operation, Soft Keys ............1-5
Demonstration Display...................1-6
2.
PLOTTER DISPLAYS
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
Presentation Modes .......................2-1
Cursor............................................2-2
Shifting the Display ........................2-2
Displaying Nav Information Window2-2
Selecting Chart Scale/Range .........2-3
Mini Chart Cards............................2-3
Navigation Data Display.................2-6
Steering Display.............................2-7
Highway Display ............................2-8
Changing Operation Mode .............2-9
Navigation Trip Distance ..............2-10
3.
TRACK
3.1
3.2
3.6
Displaying Track ............................3-1
Stopping/Restarting Plotting
of Track..........................................3-1
Changing Track Color ....................3-2
Track Plotting Method, Interval.......3-2
Changing Track Memory
Capacity.........................................3-3
Erasing Tracks...............................3-4
4.
MARK
4.1
4.2
4.3
4.4
Entering Marks...............................4-1
Changing Mark Attributes...............4-2
Changing Mark Size.......................4-3
Erasing Marks................................4-3
3.3
3.4
3.5
7.
NAVIGATION
7.1
7.2
7.4
7.5
Navigating to “Quick Points” .......... 7-1
Navigating to Waypoints
(waypoint list) ................................ 7-2
Navigating to Ports, Port
Services ........................................ 7-2
Following a Route.......................... 7-4
Canceling Navigation .................... 7-6
8.
PLOTTER ALARMS
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
Introduction ................................... 8-1
Audio Alarm On/Off ....................... 8-1
Arrival Alarm.................................. 8-2
Anchor Watch Alarm...................... 8-2
XTE (Cross Track Error) Alarm...... 8-3
Speed Alarm ................................. 8-3
Proximity Alarm ............................. 8-3
Alarm Information .......................... 8-4
9.
MEMORY CARD OPERATIONS
9.1
9.2
9.3
Formatting Memory Cards............. 9-1
Saving Data to Memory Card ........ 9-2
Loading Data from Memory Card .. 9-3
7.3
ii
TABLE OF CONTENTS
10. CUSTOMIZING YOUR UNIT
10.1 CHART SETUP OPTIONS menu 10-1
10.2 DISPLAY OPTIONS menu .......... 10-3
10.3 GPS/DGPS/TD OPTIONS
menu........................................... 10-4
10.4 CONFIGURATION menu............. 10-8
11. USING C-MAP NT MODEL
11.1
11.2
11.3
11.4
Inserting Chart Card .................. 11-1
Cursor and Data Display ............ 11-2
Tidal Information.......................... 11-3
Navigating to Ports, Port
Services ...................................... 11-4
11.5 Setting Chart Setup Options........ 11-6
11.6 Selecting Chart Scale/Range ...... 11-7
11.7 Displaying Program Number ....... 11-8
12. MAINTENANCE &
TROUBLESHOOTING
12.1
12.2
12.3
12.4
12.5
12.6
Maintenance................................ 12-1
Replacement of Fuse, Battery ..... 12-2
Simple Troubleshooting............... 12-2
Error Messages........................... 12-3
Diagnostic Tests .......................... 12-3
Clearing Memories ...................... 12-5
APPENDIX
MENU TREE ..........................................A-1
LORAN C CHAINS.................................A-3
DECCA CHAINS ....................................A-4
WORLD TIME ........................................A-5
GEODETIC CHART LIST .......................A-6
SPECIFICATIONS..................... SP-1
INDEX
DECLARATION OF CONFORMITY
iii
FOREWORD
A Word to GP-1650WD/1650W
Owners
Navigation information is displayed on a
bright 5.6-inch color TFT LCD. On-screen
information shown are position, range and
bearing to cursor position, range, bearing,
ETA and TTG to waypoint, etc.
A high sensitivity receiver tracks up to twelve
(WAAS: thirteen) satellites simultaneously.
An 8-state Kalman filter ensures optimum
accuracy in determination of vessel position,
course and speed.
Congratulations on your choice of the
FURUNO GP-1650WD COLOR
DGPS/PLOTTER, GP-1650W COLOR
GPS/PLOTTER. We are confident you will
see why the FURUNO name has become
synonymous with quality and reliability.
For over 50 years FURUNO Electric
Company has enjoyed an enviable
reputation for innovative and dependable
marine electronics equipment. This
dedication to excellence is furthered by our
extensive global network of agents and
dealers.
C-MAP NT-FP chart card is available for the
GP-1650WD/1650W.
The main features of the
GP-1650WD/1650W are
• WAAS capability.
• Comprehensive navigation data displays.
This equipment is designed and constructed
to meet the rigorous demands of the marine
environment. However, no machine can
perform its intended function unless installed,
operated and maintained properly. Please
carefully read and follow the recommended
procedures for operation and maintenance.
• Bright 5.6-inch color TFT LCD with
temperature compensated tone and
brilliance control.
• Automatic coastline chart loading.
• Position display in latitude and longitude,
Loran C or Decca TDs.
We would appreciate hearing from you, the
end-user, about whether we are achieving
our purposes.
• Improved position accuracy with optional
Thank you for considering and purchasing
FURUNO equipment.
chart card or FURUNO and C-MAP NT
mini chart cards.
DGPS beacon receiver (GP-1650W).
• Accepts both FURUNO and NAVIONICS
• Alarms: Arrival, Anchor Watch, Cross-track
Features
Error, Speed and Proximity.
• Man overboard feature records latitude
The GP-1650WD provides a totally
integrated DGPS beacon receiver, WAAS
function, GPS receiver and color video
plotter. The GP-1650W mostly shares the
same features with the GP-1650WD except
it does not have a DGPS beacon receiver.
and longitude coordinates at time of man
overboard.
• “Highway” display provides graphic
presentation of ship’s track and is useful
for monitoring cross track error.
iv
SYSTEM CONFIGURATION
GPA-017
(GP-1650W)
GPA-019
(GP-1650WD)
ANTENNA UNIT
Receives signal from
GPS satellite and beacon
reference station.
(GP-1650WD only)
DISPLAY UNIT
External equipment
(Autopilot, etc.)
DGPS beacon receiver
(GP-1650W only)
Rectifier
PR-62
Ship's mains
100/110/115/220/230 VAC
1 , 50/60 Hz
Ship's mains
12-24 VDC
This GPS receiver complies with Canadian standard RSS-210 (Low Power
License-Exempt Radio communication Devices).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
v
WHAT IS WAAS?
WAAS, available in North America, is a provider in the worldwide SBAS (Satellite Based
Augmentation System) navigation system. An SBAS provider furnishes GPS signal corrections
to SBAS users. Two more SBAS providers are also currently under development, MSAS
(Multi-Functional Satellite Augmentation System) for Japan and EGNOS (Euro Geostationary
Navigation Overlay Service) for Europe. All providers will be compatible with one another, thus
providing “seamless” position fixes to SBAS users.
150°W
120°W
90°W
60°W
30°W
0
30°E
60°E
90°E
120°E
150°E
60°N
60°N
40°N
EGNOS
MSAS
40°N
20°N
20°N
122
0
120
134
131
0
WAAS
20°S
20°S
40°S
40°S
60°S
60°S
150°W
120°W
Satellite, Region
120, AOR-E
122, AOR-W
131, IOR
134, POR
90°W
60°W
30°W
0
Position
15.5°W
54°W
64.5°E
178°E
30°E
60°E
90°E
120°E
150°E
Initial operation time
WAAS: 2003
EGNOS: 2004
MSAS: 2005
At the time of this software release, SBAS is still under development. (Providers are expected to
have initial operations capability from the times shown above.) During this developmental period,
which may last for several years, there is no guarantee of the accuracy, integrity, continuity, or
availability of the SBAS signal. Furuno will accept no responsibility for the use of the signal for
other than the above stated purpose. It is the user’s responsibility to exercise common
prudence and navigational judgment while using the SBAS signal in the developmental phase.
Note: This manual uses “WAAS” when referring to any SBAS provider.
vi
1. OPERATIONAL OVERVIEW
This chapter acquaints you with the basics of your unit - from turning on the power to the soft
key menu operation.
1.1
Display Unit Controls
• Registers own ship's positions.
• Marks man overboard position, event position.
Cursor pad
• Shifts cursor and display.
• Selects items on menus.
Registers items
on menus.
SAVE
MOB
ENTER
Soft key's functions change
depending on the display.
POWER
BRILL
ALARM
PLOT
XTE
HIWAY
WPT
RTE
ABC
1
DEF
2
GHI
3
JKL
4
MNO
5
PQR
6
STU
7
VWX
8
YZ&
9
CLEAR
_'#
0
MENU
Enter alphanumeric data.
Opens/closes
the main menu.
Mini chart card slot.
HIDE
SHOW
• Clears data.
• Erases selected waypoint.
• Silences audible alarm.
Displays/hides the soft key menu,
nav data, mode indication.
Displays the waypoint & route
menu.
Alternately selects Steering display and
Highway display.
Selects plot display.
Displays the alarm menu.
• Long press: Turns power off.
• Touch and release: Turns power on.
Opens the window for adjustment of tone and brilliance.
Display unit
1-1
1. OPERATIONAL OVERVIEW
1.2
Inserting Mini Chart
Card
Insert appropriate mini chart card before
turning on the power.
Note: Static electricity can be passed
through your fingers to a memory card
and destroy the contents of the card.
To prevent this, always touch a
metallic object, such as a steel desk,
before handling a memory card.
1.3
Turning the Power
On/Off
Turning the power on
Press the [POWER/BRILL] key at bottom
left-hand side of the display unit to turn on
the power. When the unit is turned on, it
proceeds in the sequence shown in the
figure in below, after displaying the FURUNO
information display.
Displayed for about five seconds.
START UP TEST
PROGRAM
1. Push down the lid catch to open the mini
chart card slot cover.
OK
RAM
OK
BACKUP DATA
OK
INTERNAL BATTERY
OK
GPS
OK
- - WARNING - -
Card slot
Location of mini chart
card slot cover
2. Insert appropriate mini chart card groove
side up.
Inserting groove
side up.
NO NATIONAL HYDROGRAPHIC OFFICE
HAS VERIFIED THE INFORMATION
IN THIS COASTLINE DATA CARD AND
NONE ACCEPT LIABILITY FOR THE
ACCURACY OF REPRODUCTION OR ANY
MODIFICATIONS MADE THEREAFTER.
THIS PRODUCT WITH THIS COASTLINE
DATA CARD DOES NOT REPLACE THE
REQUIREMENT TO USE THE
APPROPRIATE PRODUCTS FOR
NAVIGATION ACCORDING TO NATIONAL
AND INTERNATIONAL REGULATONS.
FURUNO ELECTRIC CO., LTD.
Displayed for about 30 seconds,
or press any key to escape.
The last-used display appears.
Start-up sequence
For any NG on the start up test display,
request service.
Mini chart card
Direction of mini chart card
3. Close the slot cover to protect the chart
drive. (Keep the slot cover closed at all
times.)
Note: Turn off power before inserting or
ejecting the mini chart card.
The GP-1650WD/1650W takes about 90
seconds to find its position when turned on
for the very first time. This is because the
equipment has no satellite data, called the
Almanac, in its database. If you want to
lessen the time needed to find position you
may enter your position manually (default
position: San Francisco, USA) on the GPS
SETUP OPTIONS menu.
Thereafter it takes about 12 seconds to find
position each time the power is turned on.
1-2
1. OPERATIONAL OVERVIEW
When the satellite signal is being received
normally, the GP-1650WD/1650W displays
various abbreviations at the bottom left-hand
corner of the display which show DGPS/GPS
receiver status. The table in below shows
these abbreviations and their meanings.
1.4
Adjusting Tone and
Brilliance
1. Press the [POWER/BRILL] key with a
touch-and-release action. The tone and
brilliance setting window appears.
Functions
Display abbreviations
Indication
Meaning
GPS 2D
2D (dimension) GPS
position fix
GPS 3D
3D GPS position fix
DGPS 2D
(GP-1650WD)
2D differential GPS
position fix
DGPS 3D
(GP-1650WD)
3D differential GPS
position fix
NO FIX
Position cannot be
found.
DOP
DOP error
DEMO
Simulation mode
GPS W2D
2D WAAS position fix
GPS W3D
3D WAAS position fix
Turning the power off
Press and hold down the [POWER/BRILL]
key until the screen goes blank. The time
remaining until the power is turned off is
shown on the screen.
Note: The example screens shown in this
manual may not match the screen you
see on your display. The screen you
see depends on your system
configuration and equipment settings.
TONE
TONE
TONE
BRILL
BRILL
BRILL
RETURN
Tone and display brilliance setting window
Soft keys
Tone and brilliance adjustment window
2. Press ◄ or ► on the cursor pad to adjust
display tone.
3. Press ▲ or ▼ on the cursor pad to adjust
display brilliance.
Note that tone and brilliance can also be
adjusted by soft keys. After pressing the
[POWER/BRILL] key, use the appropriate
soft key to adjust tone or brilliance.
Note: Tone or brilliance must be adjusted
within 10 seconds after pressing the
[POWER/BRILL] key or the tone and
brilliance adjustment window will be
erased.
1-3
1. OPERATIONAL OVERVIEW
1.5
Plotter Displays
1.6
Press the [PLOT] key. Each time this key is
pressed, the display mode changes in the
sequence shown below. For display mode,
refer to Chapter 2.
NORTH
UP
Steering/Highway
Displays
Press the [XTE/HIWAY] key. Each time this
key is pressed, the display mode changes in
the sequence shown below. For display
mode, refer to Chapter 2.
ZOOM
IN
ZOOM
OUT
230
WP-002
240
250
260
FISH
BRIDGE
DGPS 3D
NAV
POS
[Plotter Display]
DATE: JUN 02 2002
POSITION
TIME 23:59:59
TRIP:123nm
LAT/LON
34° 56.789' N
135° 56.789' E
LAT
LON
SPD
RNG
16.3 kt
CSE
245.8°
BRG
27.2 nm
245.0°
245.0°
234.5°
BRG
CSE
TTG
0.1nm
XTE
DEP
20ft
29th 14:50
0.1nm
EDIT
XT-LMT
DGPS 3D
[Steering Display]
001WPT
CSE
87.8°
BRG
RNG
SPD
BEACON
INFO
65.8°F
nm
kt
000.02nm
ZOOM
SAT
INFO
27.2
13.6
RNG
SPD
ETA
1h 59m
TD
DATUM: WGS-84
TMP
CROSS
TRACK
QP<01>
COURSE
UP
94.6°
1.88nm
10.0kt
001WPT
YUUKI
HIGHWAY
FISH01
DGPS 3D
[Nav Data Display]
0.1nm
Display modes (plotter key)
XTE
000.02nm
DGPS 3D
0.1nm
EDIT
XT-LMT
[Highway Display]
Display modes (XTE/HIWAY key)
1-4
1. OPERATIONAL OVERVIEW
1.7
Menu Operation, Soft
Keys
3. Select item with the cursor pad, and
press the EDIT soft key. For example,
select TIME DISPLAY.
Most operations are carried out through the
menu which is opened and closed with the
[MENU] key. Menus may be selected with
the five soft keys to the right of menus.
Options are selected with the cursor pad.
MENU
CHART SETUP OPTIONS
DISPLAY OPTIONS
DGPS 3D
12 HOUR
24 HOUR
Time display window
1. Press the [MENU] key to display the
main menu.
GPS/DGPS/TD OPTIONS
TIME DISPLAY
Soft
keys
4. Use the cursor pad to change the setting.
5. Press the ENTER soft key or [ENTER]
key.
6. Press the RETURN soft key.
7. Press the [PLOT] key to finish.
CONFIGURATION
Main menu
2. Press appropriate soft key to display
desired menu. For example, press the
DISPLAY OPTIONS soft key. The name
of the menu in use appears at the top
right corner of the display.
RNG & BRG MODE
RANGE/SPEED UNIT
DEPTH UNIT
TEMP UNIT
LAT/LON DISPLAY
TIME DISPLAY
WAYPOINTS SW
COURSE VECTOR
BEARING
MAG VARIATION
TD DISPLAY
POSITION DISPLAY
SET GO TO METHOD
OPERATION MODE
LANGUAGE
RHUMB LINE
nm/kt
ft
F
DD MM.MMM'
24 HOUR
AUTO2
LINE
MAGNETIC
AUTO 01.3 E
LORAN C
LAT/LON
1 POINT
PLEASURE
ENGLISH
DISPLAY
SETUP
EDIT
RETURN
DGPS 3D
Display setup menu
1-5
1. OPERATIONAL OVERVIEW
1.8
Demonstration Display
The demonstration display provides
simulated operation of this unit. On the
plotter display, own ship tracks, at the speed
selected, a figure eight course or any course
you enter, starting from position entered. All
controls are operative; you may set
destination, enter waypoints, etc
1. Press the [MENU] key, followed by the
CONFIGURATION and SYSTEM MENU
soft keys to open the system menu.
2. Press the DEMONSTRATION MODE soft
key to open the demonstration setting
screen.
DEMO MODE
DEMO SPEED
DEMO COURSE
DEMO START LAT
DEMO START LON
OFF
10.0kt
000.0°
34°12.34'N
135°12.34'E
DEMO
MODE
EDIT
EDIT soft key. Select how you want the
courseline to be traced; by FIGURE 8 or
DIR.(ection). For DIR., enter course.
10. Press the ENTER soft key or [ENTER]
key.
11. Select DEMO START LAT., and press
the EDIT soft key. Enter latitude. Use the
N< - > S soft key to switch coordinates if
necessary.
12. Press the ENTER soft key or [ENTER]
key.
13 Select DEMO START LONG, and press
the EDIT soft key. Enter longitude. Use
the E< - > W soft key to switch
coordinates if necessary.
14. Press the ENTER soft key or [ENTER]
key.
15. Press the RETURN soft key.
16. Press the [PLOT] soft key.
To cancel the demonstration display, set
DEMO MODE to OFF.
DGPS 3D
RETURN
Demo setting screen
3. Press ▲ or ▼ to select DEMO MODE.
4. Press the EDIT soft key to show the
demo mode window.
DEMO MODE
▲
▼
ON
OFF
Demo mode window
5. Press ▲ to select ON.
6. Press the ENTER soft key or the
[ENTER] key.
7. Select DEMO SPEED and press the
EDIT soft key. Enter speed. Select digit
with ◄/► and enter appropriate numeric
value with the numeric keys.
8. Press the ENTER soft key or [ENTER]
key.
9. Select DEMO COURSE and press the
1-6
2. PLOTTER DISPLAYS
2.1
Presentation Modes
The plotter display mainly shows chart,
ship’s track, waypoints, and navigation data.
Three types of display presentations are
provided for the normal plotter display:
north-up, course-up and auto course-up. To
change the mode, use the presentation
mode selection soft key, which is the 3rd soft
key from the top.
screen and points to north. A filled triangle
marks own ship’s position.
When destination is not set, the course is
upward on the screen at the moment the
course-up mode is selected.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
QP<01>
ZOOM
IN
ZOOM
OUT
AUTO
C.U.
North-up
Press the NORTH UP soft key to show the
north-up display. North (zero degree) is at
the top of the display and own ship is at the
center of the screen. Own ship marker is a
filled circle. This mode is useful for
long-range navigation.
Functions for
soft key
Course bar
Current display mode
Nav information
(north-up)
Track
window
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
NORTH
UP
ZOOM
IN
ZOOM
OUT
COURSE
UP
002WP
COURSE
UP
FISH
BRIDGE
NAV
WPT
DGPS 3D
GPS status
NAV
WPT
DGPS 3D
Plotter display, course-up mode
Auto course-up
Press the AUTO C.U. soft key to show the
automatic course-up display. When
destination is set it is at the top of the screen,
and the north mark appears at the upper left
side of the screen and points to north. A filled
triangle marks own ship’s position. The
course is at the top of screen at the moment
the automatic course-up mode is selected.
When own ship is off its intended course by
22.5° or more, it is automatically brought
back to perpendicular.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
Icon (chart) Own ship
marker
AUTO
C-UP
ZOOM
IN
ZOOM
OUT
Waypoint name
Waypoint mark
NORTH
UP
Plotter display, north-up mode
Course-up
Press the COURSE UP soft key to show the
course-up display. When destination is set it
is at the top of the screen, and the north
mark appears at the upper left side of the
NAV
WPT
DGPS 3D
Auto course-up mode
2-1
2. PLOTTER DISPLAYS
2.2
Cursor
2.3
Shifting the Display
Turning on the cursor, shifting the
cursor
The display can be shifted on the plotter
display.
Press the cursor pad to turn the cursor on,
and the cursor appears at the own ship’s
position. Operate the cursor pad to shift the
cursor. The cursor moves in the direction of
the arrow or diagonal pressed on the cursor
pad.
1. Press the cursor pad to display the
cursor.
2. Locate the cursor at a screen edge. The
screen shifts in the direction opposite of
cursor location.
Cursor position is displayed in latitude and
longitude or Loran or Decca TDs (depending
on menu setting) at the top of the plotter
display when the cursor is on.
34° 12.345' N
135° 12.345' E
FROM 16.45nm
OS
276.9°
NORTH
UP
2.4
Displaying Nav
Information Window
The nav information window can show four
data: own ship position, waypoint position,
own ship’s speed/course and off.
ZOOM
IN
ZOOM
OUT
COURSE
UP
Press the soft key at the bottom of screen.
Each press key changes data in the
sequence shown below. Soft key name also
changes.
GO TO
CURSOR
CENTER
DGPS 3D
NAV POS soft key
Displays own ship's position, course and speed.
Data displayed on the plotter display
when the cursor is on
Turning off the cursor, returning own
ship marker to screen center
The CENTER soft key turns off the cursor
and returns own ship marker to screen
center.
When the cursor is off, own ship position is
shown.
NAV WPT soft key
Displays range/bearing to the selected waypoint,
chart scale and own ship's course.
NAV S/C soft key
Displays own ship's course/speed and
water temperature*/depth.
NAV OFF soft key
Turns off the window.
*: Water temperature sensor is required.
Sequence of pressing the bottom soft key
When the cursor is on, the window at the top
of the display shows the cursor position
instead of own ship’s. To change the window
mode when the cursor is on, press the
CENTER soft key to show the appropriate
soft key.
2-2
2. PLOTTER DISPLAYS
2.5
Selecting Chart
Scale/Range
Chart scale (range) may be selected with the
ZOOM IN or ZOOM OUT soft key. ZOOM IN
expands the chart; ZOOM OUT shrinks it.
2.6
Mini Chart Cards
The mini chart cards contain nautical charts.
When you insert a suitable mini chart card in
the slot and your boat is near land, a chart
appears.
When a wrong card is inserted or a wrong
chart scale is selected, the land will be
hollow. Insert the proper card and select a
suitable chart scale. Chart icons appear to
help you select a suitable chart scale. The
table below shows the chart icons and their
meanings.
Chart icons and their meanings
Icon
Meaning
Proper card is not inserted or
chart scale is too small. Press
the soft key ZOOM IN to
adjust chart scale.
Chart scale is too large. Press
the soft key ZOOM OUT to
adjust chart scale.
Suitable chart scale is
selected.
Indices and chart enlargement
When the ZOOM OUT soft key is used, you
will see several frames appear on the chart.
These frames are called indices and they
show you what parts of the chart can be
enlarged in the current picture range. The
areas circumscribed with smaller frames can
be enlarged, but the area enclosed by the
largest frame cannot. These indices can be
erased through the menu. See page 10-2.
2-3
2. PLOTTER DISPLAYS
FURUNO chart symbols
Symbol
Description
Summit
Wreck
Lighthouse
Lighted Buoy
Buoy
Sample chart (Japan and South Korea)
Radio Station
showing indices
Position of Sounding
Remarks on chart display
Obstruction
A chart will not be displayed in the following
conditions:
Fishing Reef
• When the chart scale is too large or too
Platform
small.
When this happens, select proper chart
scale.
• When scrolling the chart outside the
indices.
Chart symbols
FURUNO mini chart card
The table below shows FURUNO mini chart
symbols and their meanings.
Anchorage
Comparison of FURUNO and Nav-ChartsTM
chart cards
Item
FURUNO
Nav-Charts™
Dot scrolling
capability
YES
YES
Course-up
display
YES
YES
Lighthouse data
YES *3
presentation
YES
Zoom at cursor
position
YES
*1
0.125, 0.5,
1, 2... 2048
nm
Same as left
Chart offset
data entry
YES
YES
Centering
YES
*2
Range at
Equator
*1 Nav-ChartsTM chart may not center the
cursor perfectly.
*2 Nav-ChartsTM chart may not center own
ship's position perfectly.
*3 Newly designed chart cards containing
lighthouse data. Chart cards for North
America area are completed, and others
are in production.
*4 Nav-ChartsTM is the registered trademark
of NAVIONICS INC.
2-4
2. PLOTTER DISPLAYS
Aid to navigation data
Selected FURUNO and NAVIONICS mini
chart cards can show buoy and lighthouse
data. Simply place the cursor on the
lighthouse or buoy mark.
Place the cursor on
a lighthouse or buoy mark.
Placing the cursor on the mark
Example of data displayed
Range and bearing
from own ship
Period (ex.: 6 seconds)
Visibility in nautical
mile (ex.: 12 miles)
Port service icons (Nav-ChartsTM
cards)
Selected Nav-ChartsTM mini chart cards
show by icons services available at ports.
Use the cursor pad to place the cursor on
the sailboat icon (denotes a port or harbor),
and then press the [ENTER] key. The
services available appear at the top of the
display.
Detailed information of service
selected
List of services
at the port selected
NORTH
UP
FIRST AID
NAVAID: /FL 6S 12M
FROM OS
52.38nm 48.0°
FL : Flashing
F
: Fixed light
F FL : Fixed and Flashing light
MO : Morse code light
Oc : Occulting light
CANCEL
DGPS 3D
Sailboat mark (Port)
Example of buoy, lighthouse data
Plotter display showing Nav-ChartsTM
port service display
Emergency
medical service
Fueling station
Water
supply station
Traveler's
service station
Customer
service station
Marine
equipment service
Port
Information center
Port service icons
2-5
2. PLOTTER DISPLAYS
2.7
Navigation Data Display
The navigation data display provide generic
navigation data and DGPS/GPS information.
Press the [PLOT] several times to show the
navigation data display.
Position Date
DATE: JUN 30 2002
POSITION
Range to waypoint
TIME 23:59:59
TRIP:123nm
12.5
LAT
LON
DATE: JUN 30 2002
ZOOM
SAT
INFO
DATUM: WGS-84
20.8ft
WAAS
satellite*
Bearing to waypoint
Temperature, depth
Geodetic chart datum
Course
Speed
Navigation data display
The navigation data display shows your
position by L/L or TD (Loran-C, Decca). To
change position format, press the
appropriate LAT/LON or TD soft key.
Enlarging an indication
An indication on the screen may be enlarged
as follows:
1. Use the cursor pad to select the
indication which you wish to enlarge.
Selected indication is circumscribed with
a red cursor.
2. Press the ZOOM soft key.
To return to the normal nav data display,
press the RETURN soft key.
12
21
07
W
20
W
E
06
BEACON
INFO
DGPS 3D
SAT
No. 30
08
05
299.9°
DEP
TIME 23:59:59
N
BRG
65.8°F
Receive signal level
Bars show satellite
signal level.
Date
TD
123.25 nm
kt
359.9°
2-6
Press the SAT INFO soft key. Your display
should look something like the following
illustration.
RNG
CSE
TMP
The GPS satellite monitor display shows
information about GPS satellites.
LAT/LON
34° 56.789' N
135° 56.789' E
SPD
GPS satellite monitor display
11
SAT
INFO
SNR
40
50
21
07
06
11
03
05
12
08
20
03
123
S
ALT
5m
RETURN
DGPS 3D
GPS fix
state
DOP 2.0
Altitude
DOP value
For WAAS
satellite*
Estimated position in the sky, and
satellite number in reverse video is
used for positioning.
*Only when WAAS fix mode is used.
GPS satellite monitor display
To return to the normal navigation data
display, press the RETURN soft key.
2. PLOTTER DISPLAYS
Beacon information display
2.8
The DGPS beacon receiver-equipped model,
can show DGPS reference station
information. Press the BEACON INFO soft
key to show the DGPS reference station
information.
The steering display provides steering
information such as range, bearing, ETA to
destination, course and speed.
Press the [XTE/HIWAY] key several times to
show the steering display.
DGPS reference station information
Receive data status
Beacon receiver setting status
MODE
FREQ
BAUD
RATE
AUTO SEARCH
288.0kHz
BEACON
INFO
OK
OK
SS
75
SN
21
DGPS 3D
Course
Compass bearing
Estimated time of arrival
Speed
Range from own ship to waypoint
Waypoint name
Bearing from
own ship to
waypoint
200 BPS
RECEIVED DATA:
BEACON STATION:
Steering Display
RETURN
Course indicator
Bearing to waypoint
CROSS
TRACK
001-WP
230
BRG
CSE
TTG
240
247.0°
245.0°
1h 59m
250
RNG
SPD
ETA
260
27.2
13.6
nm
kt
29th 14:50
Signal strength (SS),
Signal to noise ratio (SN)
0.1nm
Beacon information display
SS: SS (Signal Strength) displays a numeric
representation of field strength of the
received signal on the selected frequency.
The higher the number the stronger the
received signal. (should read at least 60.) If
noise is present at reception band width, the
figure gets bigger.
SN: SN (Signal-to-Noise) ratio displays the
ratio between the desired signal and
unwanted noise on the selected frequency.
The higher the SN ratio the better the quality
of the signal. (should read at least 21.)
Note: If your equipment does not have a
DPGS receiver, the message “NO
DIFFERENTIAL DATA” appears when
the BEACON INFO soft key is pressed.
Also when connecting with the
external beacon receiver, this
message appears.
XTE
000.02nm
DGPS 3D
XTE scale
0.1nm
EDIT
XT-LMT
Indicates the
Own ship
direction to steer
(Right: green, Left: red)
XTE
indication Amount of XTE in nautical miles
range
Time-to-go to waypoint
Steering display
How to read the compass display
The solid inverted triangle at the center of
the compass shows own ship’s course. The
hollow inverted triangle shows the bearing to
destination waypoint. When own ship’s
course is changed, the hollow inverted
triangle moves with course change.
Note: Course means the direction which
own ship moves to, it is different from the
own ship’s heading. Tide current and wind
may affect the course.
2-7
2. PLOTTER DISPLAYS
How to read the XTE indication
2.9
The black boat-shaped mark shows own
boat’s movement and direction, and the
amount to steer to return to course. Using
the figure shown on the previous page as an
example, you would steer right by 000.02
nautical miles to return to course. When this
mark is out of range of the XTE scale, the
mark color changes from black to yellow.
The range of the XTE scale can be set as
shown below.
The highway display provides a graphic
presentation of ship’s course. It is useful for
monitoring XTE - the XTE scale shows
direction and amount in nautical miles to
steer to return to course. In the figure below,
for example, you would steer right by 0.02
nm to return to course.
Highway Display
Press the [XTE/HIWAY] key once or twice to
show the highway display.
Course
Setting the range of the XTE scale
1. Press the EDIT XT-LMT soft key to
display the following window.
Waypoint mark
& name
001WPT
EDIT XTE LIMIT
Speed
Range to waypoint
Bearing to waypoint
CSE 87.8
BRG
RNG
SPD
94.6°
1.88nm
10.0 kt
WPT001
YUUKI
HIGHWAY
FISH01
0 .1nm
0.1nm
XTE range setting window
2. Use the cursor pad to select digit to
change.
3. Press appropriate alphanumeric key.
4. Press the [ENTER] key. To cancel entry,
press the CANCEL soft key instead of the
[ENTER] key.
Note that all digits may be cleared by
pressing the [CLEAR] key.
2-8
XTE
0.02nm
DGPS 3D
XTE
scale
0.1nm
EDIT
XT- LMT
Indicates the
direction to steer Own ship
(Right: green, Left: red)
Amount of XTE in nautical miles
Waypoint
Highway display
2. PLOTTER DISPLAYS
2.10 Changing Operation
Mode
Operation mode can be changed among
PLEASURE, FISHING1 and FISHING2.
FISHING1 or 2 mode provides mark/line
entry at the cursor or own ship’s position. On
FISHING 1 or 2 mode, pressing the
[HIDE/SHOW] key changes the function of
soft keys. Holding track, changing track color,
and selecting color and form of mark/line can
be performed by the soft keys directly. For
detailed FISHING mode information, see
Chapter 4.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
COURSE
UP
ZOOM
QP<01>
IN
ZOOM
OUT
AUTO
C.U.
NAV
WPT
DGPS 3D
Press the [HIDE/SHOW] key.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
COURSE
UP
STOP
TRACK
QP<01>
TRACK
COLOR
MARK
ENTRY
Soft key to
enter marlk.
MARK
EDIT
NAV
WPT
DGPS 3D
Press the [HIDE/SHOW] key.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
COURSE
UP
QP<01>
DGPS 3D
Press the [HIDE/SHOW] key.
QP<01>
DGPS 3D
Press the [HIDE/SHOW] key.
Sequence of pressing the [HIDE/SHOW] key
at FISHING 1 or 2 mode
2-9
2. PLOTTER DISPLAYS
Selecting fishing 1 or fishing 2 mode
2.11 Navigation Trip Distance
1. Press the [MENU] key and the DISPLAY
OPTIONS soft key. The display setup1
menu appears.
The navigation trip distance is displayed on
the navigation data display. Press the
[PLOT] key several times to show the
navigation data display.
RNG & BRG MODE
RANGE/SPEED UNIT
DEPTH UNIT
TEMP UNIT
LAT/LON DISPLAY
TIME DISPLAY
WAYPOINTS SW
COURSE VECTOR
BEARING
MAG VARIATION
TD DISPLAY
POSITION DISPLAY
SET GO TO METHOD
OPERATION MODE
LANGUAGE
RHUMB LINE
nm / kt
ft
°F
DD°MM.MMM'
24 HOUR
AUTO2
LINE
MAGNETIC
AUTO 01.3°E
LORAN C
LAT/LON
1 POINT
PLEASURE
ENGLISH
DISPLAY
SETUP1
Trip
EDIT
DATE: OCT 21 2000
POSITION
TIME 23:59:59
TRIP: 4792 nm
LAT/LON
34° 56.789' N
135° 56.789' E
SPD
12.5 kt
359.9°
RETURN
2. Press ▼ to select OPERATION MODE.
3. Press the EDIT soft key to show the
OPERATION MODE window.
OPERATION MODE
PLEASURE
FISHING 1
FISHING 2
Operation mode window
123.25 nm
299.9°
BRG
DATUM: WGS-84
TMP
Display setup1 menu
TD
RNG
CSE
DGPS 3D
LAT
LON
65.8°F
ZOOM
SAT
INFO
DEP
20.8ft
DGPS 3D
BEACON
INFO
Navigation data display
Note: When you enlarge POSITION, TRIP is
not displayed.
Resetting trip distance
1. Press the [MENU] key followed by the
CONFIGURATION and SYSTEM MENU
soft keys.
2. Press the MEMORY/TRIP CLEAR soft
key to open the clear memory menu.
4. Press ▲ or ▼to select PLEASURE,
FISHING1 or FISHING2.
5. Press the ENTER soft key or the
[ENTER] key to finish.
CLEAR PLOTTER MEMORY NO
CLEAR GPS MEMORY
NO
CLEAR ALL MEMORY
NO
TRIP METER RESET
NO
DGPS 3D
CLEAR
MEMORY
EDIT
RETURN
Clear memory menu
3.
4.
5.
6.
2-10
Press ▼to select TRIP METER RESET.
Press the EDIT soft key.
Press ▲ to select YES.
Press the ENTER soft key or the
[ENTER] key to reset trips distance.
3. TRACK
3.1
Displaying Track
1. Press the [MENU] key to open the main
menu.
MENU
CHART SETUP OPTIONS
DISPLAY OPTIONS
GPS/DGPS/TD OPTIONS
DGPS 3D
CONFIGURATION
Main menu
2. Press the CHART SETUP OPTIONS soft
key to open the CHART SETUP
OPTIONS menu.
CHART
SETUP
CHART OFFSET
The default setting is ON, which traces ship’s
track in accordance with ship’s movements.
Number of track and mark points used
appears in the TRACK STATUS window on
the TRACK CONTROL display. Using the
illustration at the bottom of the page as an
example, it shows that 1000 out of 2000
track points and 5 out of 3000 mark shave
been used.
3.2
TRACK CONTROL
CHART DETAILS
RETURN
DGPS 3D
4. Press ▲ to select DISPLAY TRACK.
5. Press the EDIT soft key to show the
display track window.
6. Press ▲ or ▼ to select ON or OFF as
appropriate.
7. Press the ENTER soft key or the
[ENTER] key.
8. Press the [PLOT] key to close the menu.
Chart setup menu
3. Press the TRACK CONTROL soft key to
open the TRACK CONTROL menu.
DISPLAY TRACK ON
TRACK COLOR WHITE
PLOT
TIME
TIME INTERVAL 01m00s
DIST INTERVAL 00.10 nm
TRACK MEMORY 2000 POINTS
(MARK MEMORY) (3000) POINTS
TRACK STATUS
TRACK
CONTROL
EDIT
STOP
TRACK
ERASE
T&M
TRACKING
TRACK : 1000 / 2000 PTS used
MARK :
5 / 3000 PTS used
RETURN
Stopping/Restarting
Plotting of Track
When your boat is at anchor or returning to
port you probably won’t need to record its
track. You can stop recording the track, to
conserve the track memory, as follows:
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and TRACK
CONTROL soft key.
2. Press the STOP TRACK soft key. The
indication “TRACKING” in the TRACK
STATUS window changes to “NOT
TRACKING”.
On the plotter display, H icon appears.
To restart recording the track, press the
START TRACK soft key at step 2 in the
above procedure.
DGPS 3D
Track control menu
3-1
3. TRACK
When the fishing mode is selected, you can
stop or restart plotting the track with the soft
key only on the plotter display. Press the
[HIDE/SHOW] key several times to show the
STOP TRACK soft key on the plotter display.
Press the STOP TRACK soft key to stop
plotting of track. The message of HOLD
TRACK PLOTTING appears approx. 2
seconds and then own ship mark changes to
hollow circle. To restart plotting the track,
press the START TRACK soft key again. The
message START TRACK PLOTTING
appears approx. 2 seconds and then plotting
restarts.
3.3
Changing Track Color
Track can be displayed in red, yellow, green,
light-blue, purple, blue or white. It can be
useful to change track color to discriminate
between previous day's track, past track, etc.
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and TRACK
CONTROL soft keys.
2. Press ▲ or ▼ to select TRACK COLOR.
3. Press the EDIT soft key to display the
TRACK COLOR window.
TRACK COLOR
▲
▼
RED
YELLOW
GREEN
LIGHT BLUE
PURPLE
BLUE
WHITE
Track color window
4. Press ▲ or ▼ to select the color desired.
5. Press the ENTER soft key to finish.
When the fishing mode is selected, you can
change track color with the soft key only on
the track display.
3-2
1. Press the [HIDE/SHOW] key several
times to show the TRACK COLOR soft
key on the plotter display.
2. Press the TRACK COLOR soft key to
show the TRACK COLOR window.
3. Press ▲ or ▼ to select the color desired.
4. Press the ENTER soft key or the
[ENTER] key to finish, or press the
CANCEL soft key to escape.
3.4
Track Plotting Method,
Interval
In drawing the track, first the ship’s position
(fed from the DGPS/GPS receiver, WAAS) is
stored into the unit’s memory at an interval of
time or distance. A shorter interval provides
better reconstruction of the track, but the
storage time of the track is reduced. When
the track memory becomes full, the oldest
track is erased to make room for the latest.
Track plotting method
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and TRACK
CONTROL soft keys.
2. Press ▲ or ▼ to select PLOT.
3. Press the EDIT soft key to display the
PLOT window.
PLOT
▲
▼
TIME
DISTANCE
Plot window
4. Press ▲ or ▼ to select TIME or
DISTANCE. Distance is useful for
conserving track memory, since no track
is recorded when the boat is stationary.
5. Press the ENTER soft key or the
[ENTER] key.
3. TRACK
Track plotting interval
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and TRACK
CONTROL soft keys.
2. Press ▲ or ▼ to select TIME INTERVAL
or DIST INTERVAL.
3. Press the EDIT soft key to display the
INTERVAL window.
3. Press the EDIT soft key to display the
TRACK MEMORY window.
TRACK MEMORY
1000/5000 POINTS
Track memory window
TIME INTERVAL
01 m 00 s
(When selecting TIME INTERVAL.)
DIST INTERVAL
The track memory window may be
erased by pressing the CANCEL soft key
to escape.
4. Enter number of track memory points
desired, with the alphanumeric keys.
00.10 nm
(When selecting DIST INTERVAL.)
Interval window
4. Use the cursor pad to place the cursor on
the digit desired. The [CLEAR] key
functions to clear an entire line of data.
5. Press appropriate alphanumeric key to
enter value.
6. Repeat steps 4 and 5 to complete.
7. Press the ENTER soft key or the
[ENTER] key.
Note that all digits may be cleared by
pressing the CLEAR soft key or the
[CLEAR] key.
5. Press the ENTER soft key or the
[ENTER] key. The following window
appears to ask you if you are sure to
change the track memory capacity.
RESETTING ERASES
TRACK, MARK/LINE
ALREADY SAVED. OK?
YES ... "ENTER" key
NO ... "CLEAR" key
Erase message
3.5
Changing Track Memory
Capacity
The equipment stores a total of 5000 points
of track and marks. This total may be freely
apportioned as desired. The default setting is
2000 points for track and 3000 points for
mark. Note that when the track memory
capacity is changed, all tracks and marks
in the memory are erased.
6. Press the [ENTER] key to change
apportion, or press the [CLEAR] key to
escape.
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and TRACK
CONTROL soft keys.
2. Press ▼ to select TRACK MEMORY.
3-3
3. TRACK
3.6
Erasing tracks by color
Erasing Tracks
Be absolutely sure you want to erase track;
erased track cannot be restored.
Erasing tracks by area
You can erase tracks within an area you set.
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS, TRACK
CONTROL and ERASE T & M soft keys.
ERASE ALL TRACKS
ERASE TRACKS BY AREA
ERASE TRACKS BY COLOR
ERASE ALL MARKS/LINES
ERASE MARKS BY AREA
ERASE
EDIT
Tracks can be erased by on color.
1. Press the [MENU] key followed by the
CHART SETUPOPTIONS, TRACK
CONTROL and ERASE T & M soft key.
2. Select ERASE TRACK BY COLOR, and
then press the EDIT soft key.
3. Select the color which you want to erase.
4. Press the ENTER soft key or [ENTER]
key. You are asked if you are sure to
erase.
5. Press the [ENTER] key to erase, or
press the [CLEAR] key to escape.
Erasing all track
TRACK STATUS
You can erase all track.
TRACKING
TRACK : 1000 / 2000 PTS used
MARK :
5 / 3000 PTS used
RETURN
DGPS 3D
Erase menu
2. Select ERASE TRACK BY AREA, and
then press the EDIT soft key.
3. Move the cursor to the starting point of
the area to erase.
4. Press the START soft key.
5. Move the cursor to the ending point of
the area to erase.
6. Press the END soft key. You are asked if
you sure to erase.
7. Press the [ENTER] key to erase, or
press the [CLEAR] key to escape.
3-4
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS, TRACK
CONTROL and ERASE T& M soft keys.
2. Select ERASE ALL TRACKS, and then
press the EDIT soft key.
You are asked if you sure to erase all track.
3. Press the [ENTER] key to erase, or press
the [CLEAR] key to escape.
4. MARK
You can enter marks to denote important
locations, such as a good fishing spot. In the
default condition, you may enter 3000 marks.
Plotter display
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
ZOOM
QP<01>
4.1
IN
ZOOM
OUT
Entering Marks
Select the FISHING 1 or FISHING 2 mode to
enable entry of marks on the PLOTTER
display. Select the location desired with the
cursor, or turn off the cursor to enter the
mark at own ship position. Press the MARK
ENTRY soft key to enter the mark. The mark
is entered in the shape and color selected
from the MARK SHAPE and MARK COLOR
windows.
In the FISHING 1 or FISHING 2 mode,
pressing the [HIDE/SHOW] key changes the
function of the soft keys as follows.
COURSE
UP
AUTO
C.U.
NAV
WPT
DGPS 3D
Press the [HIDE/SHOW] key.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
COURSE
UP
STOP
TRACK
QP<01>
TRACK
COLOR
MARK
ENTRY
MARK
EDIT
Soft key
to enter mark.
NAV
WPT
DGPS 3D
Press the [HIDE/SHOW] key.
34° 12.345' N
135° 12.345' E
CSE 245.8°
SPD 16.3kt
COURSE
UP
QP<01>
DGPS 3D
Press the [HIDE/SHOW] key.
QP<01>
DGPS 3D
Press the [HIDE/SHOW] key.
Changing displays
(PLOTTER display)
4-1
4. MARK
4.2
Changing Mark
Attributes
Mark line
You can select shape, line and color of
marks and lines on the plotter display.
1. Press the [HIDE/SHOW] key to show the
MARK EDIT soft key.
2. Press the MARK EDIT soft key to show
the MARK/LINE window.
MARK
EDIT
MARK SHAPE
.
MARK LINE
MARK
SHAPE
MARK
LINE
YELLOW
MARK COLOR
MARK
COLOR
RETURN
DGPS 3D
Mark/line window
3. Press the MARK SHAPE soft key to
change mark shape, the MARK LINE soft
key to change mark line, or the MARK
COLOR soft key to change mark color.
Press the MARK LINE soft key to display
the MARK LINE window. Press ▲ or ▼
to select mark line desired.
MARK LINE
▲
Mark does not
have a line.
▼
Mark line window
Mark color
Press the MARK COLOR soft key to
display the MARK COLOR window.
Press ▲ or ▼ to select mark color
desired.
MARK COLOR
▲
RED
YELLOW
GREEN
LIGHT BLUE
PURPLE
BLUE
WHITE
▼
Mark color window
Mark shape
Press the MARK SHAPE soft key to
display the MARK SHAPE window. Press
▲ or ▼ to select mark shape desired.
MARK SHAPE
▲
✕
▼
Mark shape window
4-2
4. Press the ENTER soft key or the
[ENTER] key.
5. Press the RETURN soft key to finish.
Marks/lines entered hereafter are inscribed
in the shape, color and line type selected
here.
4. MARK
4.3
Changing Mark Size
Erasing marks/lines in an area
Mark size can be selected from STD
(standard) and SMALL.
You can erase marks and lines within an
area you select.
1. Press the [MENU] key to display the
main menu.
2. Press the CHART SETUP OPTIONS soft
key.
3. Press the CHART DETAILS soft key to
open the CHART DETAILS menu.
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS, TRACK
CONTROL and ERASE T & M soft keys.
2. Press ! or " to select ERASE MARKS
BY AREA, and then press the EDIT soft
key.
The plotter display appears.
3. Move the cursor to the starting point of
the area to erase.
4. Press the START soft key.
5. Press the cursor pad to make a square.
6. Press the END soft key.
You are asked if you sure to erase the
marks/lines in the area you selected.
7. Press the [ENTER] key to erase, or
press the [CLEAR] key to escape.
LAT/LON GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
OFF
WHITE
STD
CHART
DETAIL
EDIT
DEPTH
INFO
RETURN
DGPS 3D
Erasing all marks/lines
Chart details menu
4. Press ▼ to select MARK SIZE.
5. Press the EDIT soft key.
6. Press ▲ or ▼ to select STD (standard)
or SMALL.
7. Press the [ENTER] key.
4.4
Erasing Marks
Erasing individual marks/lines
1. Operate the cursor pad to place the
cursor on the mark you want to erase.
2. Press the [CLEAR] key. The mark
selected is erased.
You can erase all marks and lines. Be
absolutely sure you want to erase all marks
and lines; erased marks and lines cannot be
restored.
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS, TRACK
CONTROL and ERASE T& M soft keys.
2. Select ERASE ALL MARKS/LINES. And
then press the EDIT soft key.
You are asked if you are sure to erase all
marks and lines.
3. Press the [ENTER] key to erase, or
press the [CLEAR] key to escape.
Note: To erase a line, place the cursor on
an edge of the line. The line
segment will be erased.
4-3
4. MARK
4.5
Displaying Track and
Mark Points
Number of track and mark points used
appears in the TRACK STATUS window on
the TRACK CONTROL display.
DISPLAY TRACK ON
TRACK COLOR WHITE
PLOT
TIME
TIME INTERVAL 01m00s
DIST INTERVAL 00.10 nm
TRACK MEMORY 2000 POINTS
(MARK MEMORY) (3000) POINTS
TRACK STATUS
TRACK
CONTROL
EDIT
STOP
TRACK
ERASE
T&M
TRACKING
TRACK : 1000 / 2000 PTS used
MARK :
5 / 3000 PTS used
RETURN
DGPS 3D
Track control menu
4.6
Target Mark
A target mark ( ) shows a radar target’s
position. This mark is inscribed on the plotter
display and saved as a waypoint when a
certain key is pressed on the radar. Some
FURUNO radars can output a target mark to
this plotter.
4-4
5. WAYPOINTS
5.1
Entering Waypoints
In navigation terminology, a waypoint is a
particular location on a voyage whether it be
a starting, intermediate or destination point.
A waypoint is the simplest piece of
information your equipment requires to get
you to a destination, in the shortest distance
possible. This unit has 835 waypoints
(including quick waypoints) into which you
can enter position information. There are five
methods by which you can enter a waypoint:
at own ship’s position, at MOB position, by
cursor, by range and bearing, and through
the waypoint list (manual input of latitude
and longitude).
Entering waypoints at own ship’s
position
You can save your current position as a
waypoint. Press the [SAVE/MOB] key with a
touch-and-release action to store your
position. This new waypoint will
automatically be saved in the waypoint list
under the next consecutive waypoint
number.
For FISHING 2 mode, immediately after
pressing the MOB key, you can change the
mark shape, color etc. similar to that shown
in the procedure on the next page. Press the
SAVE soft key to enter the mark.
2. Press the [ENTER] key to select MOB
position as destination, or the [CLEAR]
key to only mark MOB position.
3. To show range and bearing to the MOB
position, press the NAV L/L soft key
followed by the NAV WPT soft key.
Bearing and range
to MOB position
MOB
mark
Range, bearing
Man
overboad
M
(MOB)
Current
position
MOB concept
To erase a MOB mark in the PREASURE
and FISHING 1 modes, you must erase both
the waypoint it is registered under and the
MOB mark itself. Place the cursor on the
MOB mark and press the [CLEAR] key
followed by the [ENTER] key to erase the
waypoint. (A flashing diamond appears over
the waypoint when it has been correctly
selected.) Repeat to erase the MOB mark.
Entering waypoints by the cursor
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
WPT
& ROUTE
Entering waypoints at MOB position
The MOB mark functions to mark man
overboard position.
1. When man overboard, press the
[SAVE/MOB] key several seconds to
display the following message.
MAN OVER BOARD!
GO TO (MOB)?
YES ... "ENTER" key
NO ... "CLEAR" key
WAYPOINTS
ROUTES
LOG
CREATE VOYAGE BASED ROUTE
DGPS 3D
Waypoint & route menu
MOB message
5-1
5. WAYPOINTS
2. Press the WAYPOINTS soft key to
display the WAYPOINTS menu.
ADD/EDIT/MOVE WAYPOINTS
WPT
LOCAL LIST
Changing the shape and color of waypoint
mark
1. Press the SELECT MARK soft key.
2. Press the MARK SHAPE soft key to open
the mark shape selection window.
ALPHA/NUMERIC LIST
MARK SHAPE
WAYPOINT BY CURSOR
WAYPOINT BY RANGE & BEARING
RETURN
DGPS 3D
Waypoints menu
3. Press the WAYPOINT BY CURSOR soft
key. The plotter display appears.
4. Operate the cursor pad to place the
cursor on the location desired.
5. Press the NEW WPT soft key. The
waypoint window appears and it shows
mark shape, waypoint name, comment
(default: date), position of waypoint and
proximity alarm radius.
MARK NAME
0 0 1 WPT
COMMENT
17:38 02JUN02
LAT
LON
34 12. 345' N
135 12. 3457' W
PROXIMITY
ALARM RADIUS
NEW
WPT
SELECT
MARK
COORD
TYPE
N<-->S
E<-->W
SAVE
0.00 nm
Mark shape selection window
3. Operate the cursor pad to select shape
desired.
4. Press the ENTER soft key or the
[ENTER] key.
5. Press the SELECT MARK soft key.
6. Press the MARK COLOR soft key to
open the mark color selection window.
SELECT COLOR
▲
RETURN
DGPS 3D
Waypoint window
6. If you do not need to change the
waypoint data, simply press the SAVE
soft key to register the waypoint and
return to the plotter display. If you want to
change waypoint data as shown in the
next several paragraphs, be sure to
press the SAVE soft key only after
changing all data you want to change.
5-2
▼
RED
YELLOW
GREEN
LIGHT BLUE
PURPLE
BLUE
WHITE
Mark color selection window
7. Press ▲ or ▼ to select the color desired,
and then press the ENTER soft key or
the [ENTER] key.
5. WAYPOINTS
Changing waypoint name, comment,
proximity alarm radius
Entering waypoints by range and
bearing
1. If necessary, you can change the name
(up to 6 characters), comment (up to 13
characters), L/L position and the
proximity alarm radius (explained in detail
in Chapter 8) as follows:
a) Select the NAME, COMMENT or
This method is useful when you want to
enter a waypoint using range and bearing to
a target found on a radar.
PROXIMITY ALARM RADIUS field.
b) Use the cursor pad to select character or
digit.
c) Enter appropriate data with the
alphanumeric keys.
Note: You cannot change shape and color of
a waypoint when it has a proximity
alarm radius entered. To change
shape or color, enter all zeroes as the
proximity alarm radius.
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
2. Press the WAYPOINTS soft key to open
the waypoint menu.
3. Press the WAYPOINT BY RANGE &
BEARING soft key. The plotter screen
appears.
34° 12.345' N
135° 12.345' E
FROM
'X'
0.01nm
224.1
WPT
RNG BRG
ZOOM
IN
ZOOM
OUT
X
NEW
WPT
START
POINT
Changing waypoint position
1. Use the cursor pad to place the cursor in
the LAT LON field.
2. Operate the cursor pad to place the
cursor on digit to change. Enter
appropriate data with the alphanumeric
keys.
3. You can switch co-ordinates with the
N<-->S/E<-->W soft key.
DGPS 3D
RETURN
Plotter display, range and bearing selected
as waypoint entry method
4. Operate the cursor pad to place the
cursor on the location desired. The range
and bearing from own ship to cursor
appear at the top of the screen.
Note: The origin point of range and
bearing can be shifted to the place
you desire. Operate the cursor pad
to select location, and then press
the soft key START POINT. “X”
appears at the cursor position.
5. Press the NEW WPT soft key to show the
waypoint window.
6. If necessary, change data as you did in
“Entering waypoints by the cursor.”
7. Press the SAVE soft key to register the
waypoint.
5-3
5. WAYPOINTS
Entering waypoints by latitude and
longitude position
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
2. Press the WAYPOINTS soft key to open
the WAYPOINT menu.
3. Press the LOCAL LIST (lists waypoints in
order from nearest to furthest) or
ALPHA/NUMERIC LIST (lists waypoints
in alphanumeric order) soft key.
BRG.
WPT
LOCAL
23.8°
1.75nm
FISH01 RNG.
33°12.345' N
ABCDEFGHIJKL
135°23.456' W
GO TO
WPT001
12:30 29SE97
BRG. 90.0°
RNG. 2.51nm
33°23.456' N
135°23.567' W
BRG.
NEW
WPT
EDIT
WPT
180.0°
5.07nm
ABCDEF RNG.
34°12.345' N
15:21 01OCT97
135°54.321' W
BRIDGE
BRG. 359.9°
RNG. 8.01nm
34°12.345' N
135°54.321' W
16:45 01OCT97
ERASE
WPT
RETURN
DGPS 3D
Local list
BRG.
180.0°
5.07nm
ABCDEF RNG.
34°12.345' N
15:21 01OCT97
135°54.321' W
BRIDGE
BRG. 359.9°
RNG. 8.01nm
34°12.345' N
135°54.321' W
WPT
ALPHA
GO TO
16:45 01OCT97
BRG.
23.8°
1.75nm
FISH01 RNG.
33°12.345' N
ABCDEFGHIJKL
WPT001
12:30 29SE97
DGPS 3D
135°23.456' W
BRG. 90.0°
RNG. 2.51nm
NEW
WPT
EDIT
WPT
ERASE
WPT
33°23.456' N
135°23.567' W
RETURN
SEARCH FOR _ _ _
Search window
Alphanumeric list
4. Press the NEW WPT soft key to show the
waypoint window. Own ship’s position is
shown. Change the data similar to how
you did in “Entering waypoints by the
cursor.”
5. Press the SAVE soft key.
5-4
5.2
Erasing Individual
Waypoints
Individual waypoints can be erased by the
cursor or through the waypoint list.
Erasing waypoints by the cursor
1. Press the cursor pad to turn on the
cursor.
2. Operate the cursor pad to place the
cursor on the waypoint you want to erase.
A flashing diamond mark appears over
the waypoint when it is correctly selected.
3. Press the [CLEAR] key. You are asked if
you are sure to erase the waypoint.
4. Press the [ENTER] key. The waypoint is
erased from both the plotter screen and
the waypoint list.
Erasing waypoints through the
waypoint list
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
2. Press the WAYPOINTS soft key to open
the WAYPOINTS menu.
3. Press the LOCAL LIST or
ALPHA/NUMERIC LIST soft key.
4. Press ▲ or ▼ to select the waypoint you
want to erase.
5. Press the ERASE WPT soft key. You are
asked if you are sure to erase the
waypoint.
6. Press the [ENTER] key. The waypoint is
erased from both the waypoint list and
the plotter screen.
5. WAYPOINTS
5.3
Changing Waypoint Data
You can change the waypoint data through
the waypoint list.
1. Press the [WPT/RTE] key, WAYPOINTS,
and LOCAL LIST or ALPHA/NUMERIC
LIST soft keys.
2. Press ▲ or ▼ to select the waypoint you
want to change.
3. Press the EDIT WPT soft key.
4. Change data as you did in “Entering
waypoints by the cursor.”
5. Press the SAVE soft key.
5.4
Changing Waypoint
Position on the Plotter
Display
You may change the position of waypoints
on the plotter display as follows:
1. Press the [WPT/RTE] key followed by the
WAYPOINTS soft key to open the
WAYPOINTS menu.
2. Press the WAYPOINT BY CURSOR soft
key. The plotter display appears.
3. Operate the cursor pad to place the
cursor on the waypoint which you want to
change. A flashing diamond mark
appears on the waypoint when it is
correctly selected.
4. Press the EDIT/MOVE soft key.
5. Press the MOVE WPT soft key.
6. Operate the cursor pad to place the
cursor on the location desired.
7. Press the [ENTER] key.
The waypoint moves to the cursor position
and its new position is recorded on the
waypoint list. If the waypoint is set as
destination or is part of a route, you are
asked if you are sure to move the waypoint.
In this case, press the [ENTER] key again to
move the waypoint, or the [CLEAR] key to
cancel move.
5-5
5. WAYPOINTS
5.5
Waypoint Mark Size
You may change the size of all waypoint
marks to small or large (default), or turn
them off.
1. Press the [MENU] key to open the main
menu.
2. Press the CHART SETUP OPTIONS soft
key.
3. Press the CHART DETAILS soft key to
open the CHART DETAILS menu.
5.6
Searching Waypoints
You can search for a waypoint through the
alpha/numeric list as follows:
1. Press the [WPT/RTE] key, and then
press the WAYPOINTS and
ALPHA/NUMERIC LIST soft keys to
show the alphanumeric list. At the bottom
of the display the search window
appears.
SEARCH FOR _ _ _
LAT/LON GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
OFF
WHITE
STD
CHART
DETAIL
Search window
EDIT
DEPTH
INFO
RETURN
DGPS 3D
Chart details menu
4. Press ▲ or ▼ to select WAYPOINT.
5. Press the EDIT soft key.
6. Press ▲ or ▼ to select LARGE, SMALL
or OFF. LARGE shows mark in actual
shape as shown on page 6-2. SMALL
displays all waypoints with an “X”
regardless of mark shape selected.
7. Press the ENTER soft key or [ENTER]
key.
5-6
2. Use the alphanumeric keys to enter the
first 1 - 3 characters in the search window.
The waypoint searched appears at the
top of the screen.
6. ROUTES
Often a trip from one place to another
involves several course changes, requiring a
series of route points (waypoints) which you
navigate to, one after another. The sequence
of waypoints leading to the ultimate
destination is called a route. Your unit can
automatically advance to the next waypoint
on a route, so you do not have to change the
destination waypoint repeatedly.
You can store up to 200 routes. A route may
consist of 35 points.
6.1
Entering Routes
Entering routes through the route list
This method constructs routes using existing
waypoints.
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
2. Press the ROUTES soft key to open the
ROUTE menu.
ABCDEF
ABCDEFGHIJKL
LENGTH
56.7 nm
WAYPOINTS
6
BRIDGE
12:30 29SE97
FISH01
15:21 01OCT97
HPT001
16:45 01OCT97
DGPS 3D
LENGTH
25.6 nm
WAYPOINTS
35
LENGTH
21.1 nm
WAYPOINTS
3
LENGTH
4.7 nm
WAYPOINTS
1
SEARCH FOR _ _ _
ROUTE
GO TO
NEW
ROUTE
EDIT
ROUTE
ERASE
ROUTE
RETURN
RETURN
Route menu
3. Press the NEW ROUTE soft key to open
the new route entry window.
ROUTE NAME
001
COMMENT
NEW
ROUTE
PLOT
LOCAL
LIST
ALPH
LIST
CONECT
ROUTE
DGPS 3D
CANCEL
New route entry window
6-1
6. ROUTES
4. If desired you can change the route
name shown and/or add a comment. To
change route name, press the [CLEAR]
key to clear the route name. Use the
cursor pad to position the cursor and
then press appropriate alphanumeric key.
To enter a comment, place the cursor in
the COMMENT window. Use the cursor
pad and alphanumeric keys to enter your
comment. A route name may consist of
six characters; comment, 13 characters.
5. Press the LOCAL LIST or ALPH LIST soft
key to open the waypoint list.
6. Press ▲ or ▼ to select a waypoint, and
press the ADD WPT soft key to add it to
the route.
7. Repeat step 6 to complete the route.
When you want to clear a waypoint
selected, press the ERASE LST WP soft
key. Each press of this key deletes the
last waypoint entered.
8. Press the SAVE soft key to register the
route.
6.2
Connecting Routes
Two routes can be connected as follows:
1. Press the [WPT/RTE] key followed by the
ROUTES and NEW ROUTE soft keys to
open the NEW ROUTE menu.
2. Enter the name for new route.
3. Press the CONECT ROUTE soft key.
4. Enter the registered route name for the
first route beneath FIRST in the
CONNECT ROUTE window.
CONNECT ROUTE
FIRST
SECOND
______
______
FORWARD
REVERSE
NEW
ROUTE
F<-->R
SAVE
DGPS 3D
CANCEL
Connect route window
Entering routes by the cursor
This method allows you to construct a route
directly on the plotter display, using existing
waypoints or new locations. Any new
location will be saved as a waypoint, under
the next consecutive waypoint number.
1. Follow step 1-4 in “Entering routes
through the route list.”
2. Press the PLOT soft key. The plotter
display appears.
3. Operate the cursor pad to place the
cursor on an existing waypoint (ADD
WPT soft key appears) or new location
(ADD NEW WPT soft key appears).
4. Press the ADD WP (ADD NEW WPT)
soft key.
5. Repeat steps 3 and 4 to complete the
route.
6. Press the [ENTER] key to register the
route.
6-2
5. Press the F<-->R soft key to select
direction to transverse the waypoints of
the route; forward or reverse.
6. Enter the route name of the second route
similar to how you did for the first route.
7. Press the SAVE soft key.
Note: The maximum number of waypoints in
a route is 35. If this number is
exceeded an error message appears.
In this case, delete waypoints in one
or both routes so the total number of
waypoints does not exceed 35.
6. ROUTES
6.3
Inserting, Removing
Waypoints
Inserting waypoints through the route
list
Waypoints can be inserted in routes as
follows:
7. Press ▲ or ▼ to select the waypoint you
want to insert. You can switch between
the local list and alphanumeric list by
pressing the LOCAL LIST or ALPH LIST
soft key.
8. Press the SELECT WPT soft key.
Changing waypoints through the list
1. Press the [WPT/RTE] key followed by the
ROUTES soft key to open the ROUTE
menu.
2. Select a route by pressing ▲ or ▼.
3. Press the EDIT ROUTE soft key. The
route name screen appears.
4. Press the LOCAL LIST soft key. All
waypoints in the route are displayed.
EDIT
ROUTE
ROUTE NAME: ABCDEF
COMMENT: ABCDEFGHIJKL
01
WPT001
02
WPT002
03
WPT003
04
WPT004
05
WPT005
34 .12.345'N
135 .54.321'W
34 .23.456'N
136 .10.255'W
35 .11.222'N
136 .55.889'W
35 .22.878'N
136 .44.333'W
34 .15.279'N
135 .34.111'W
LEG
204.8
33.83nm
22.0
34.27nm
35.1
2.89nm
125.6
31.25nm
INSERT
WPT
REMOVE
WPT
CHANGE
WPT
COORD
TYPE
RETURN
RETURN
DGPS 3D
Waypoints used in a route can be changed
with others.
1. Press the [WPT/RTE] key followed by the
ROUTES soft key to open the ROUTE
menu.
2. Select a route by pressing ▲ or ▼.
3. Press the EDIT ROUTE soft key. The
route name screen appears.
4. Press the LOCAL LIST soft key.
5. Select the waypoint which you want to
change (remove).
6. Press the CHANGE WPT soft key to
show the local list.
7. Select the waypoint which you want to
change (insert).
8. Press the CHANGE WPT soft key to
change the waypoint.
9. Press the [PLOT] key.
Edit route menu
5. Press ▲ or ▼ to place the cursor at the
location where you want to insert a
waypoint.
6. Press the INSERT WPT soft key to show
the waypoint list.
EDIT
ROUTE
ROUTE NAME: ABCDEF
COMMENT: ABCDEFGHIJKL
01
WPT001
02
WPT002
03
WPT003
04
WPT004
05
WPT005
DGPS 3D
34 .12.345'N
LIST
135LOCAL
.54.321'W
LEG
204.8
33.83nm
WPT010
34 .23.456'N
001
100136 .10.255'W 22.0
34.27nm
WPT011
35 .11.222'N
002
136 .55.889'W
35.1
2.89nm
WPT012
35 .22.878'N
003
136 .44.333'W
125.6
WPT013
34 .15.279'N
31.25nm
004
135 .34.111'W
SELECT
WPT
COORD
TYPE
LOCAL
LIST
ALPH
LIST
RETURN
CANCEL
Waypoint list for editing a route (Local list)
6-3
6. ROUTES
Inserting waypoints on the plotter
display
Inserting waypoints before the first
waypoint or after the last waypoint
1. Press the [WPT/RTE] key followed by the
ROUTES soft key to open the ROUTE
menu.
2. Press ▲ or ▼ to select the route desired.
3. Press the EDIT ROUTE soft key.
4. Press the PLOT soft key to show the
plotter screen.
5. Operate the cursor pad to place the
cursor on the first or last waypoint of the
route which you want to insert.
6. Press the ADD TO START (ADD TO
END) soft key.
7. Operate the cursor pad to place the
cursor on an existing waypoint (ADD
WPT soft key appears) or new location
(ADD NEW WPT soft key appears).
8. Press the ADD WPT (ADD NEW WPT)
soft key.
9. Press the [ENTER] key.
When you want to insert waypoints after the
last waypoint, press the “ADD TO END” soft
key at step 6.
Inserting waypoints in an intermediate
location within a route
1. Follow steps 1 through 4 in “Inserting
waypoints before the first waypoint or
after the last waypoint.”
2. Operate the cursor pad to place the
cursor on a line connecting waypoints.
3. Press the SPLIT LEG soft key. The
selected line turns red.
4. Operate the cursor pad to place the
cursor on an existing waypoint (INSERT
WPT soft key appears) or new location
(INSERT NEW WPT soft key appears).
5. Press the appropriate soft key, INSERT
WPT or INSERT NEW WPT.
6-4
Removing waypoints from routes
Removing route waypoints through the
route list
1. Press the [WPT/RTE] key followed by the
ROUTES soft key to open the ROUTE
menu.
2. Press ▲ or ▼ to select the route desired.
3. Press the EDIT ROUTE and LOCAL LIST
soft keys to show the waypoint list.
4. Press ▲ or ▼ to select the waypoint you
want to delete.
5. Press the REMOVE WPT soft key.
Removing route waypoints from the plotter
display
1. Press the [WPT/RTE] key followed by the
ROUTES soft key to open the ROUTE
menu.
2. Press ▲ or ▼ to select the route desired.
3. Press the EDIT ROUTE soft key.
4. Press the PLOT soft key to show the plot
screen.
5. Operate the cursor pad to place the
cursor on the waypoint you want to
remove from the route.
6. Press the REMOVE WPT soft key.
6. ROUTES
6.4
Creating Track-based
Routes
You can create routes based on your ship’s
track by entering waypoints at own ship’s
position. This feature is useful when you
wish to retrace a track.
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
2. Press the CREATE VOYAGE BASED
ROUTE soft key to show the save route
menu.
4. If required, you may change the route
name and enter a comment, using the
[CLEAR] key, cursor pad and
alphanumeric keys.
5. Press the START LOG soft key to show
the track-based route screen. If you
entered an existing route name at step 4,
you are asked if you want to add
track-based waypoints to the existing
route. Then, press the [ENTER] key to
select YES, or the [CLEAR] key to
escape.
SAVE
ROUTE
ROUTE NAME: XYZ
COMMENT: BEST FISHING
ABCDEF
ABCDEFGHIJKL
BRIDGE
12:30 29SE97
FISH01
15:21 01OCT97
LENGTH
25.6 nm
WAYPOINTS
35
LENGTH
56.7 nm
WAYPOINTS
6
SAVE
ROUTE
NEW
SELECT
ROUTE
LENGTH
21.1 nm
WAYPOINTS
3
LEG
01
FINISH
LOG
02
03
04
COORD
TYPE
05
HPT001
16:45 01OCT97
DGPS 3D
LENGTH
4.7 nm
WAYPOINTS
1
SEARCH FOR _ _ _
RETURN
RETURN
RETURN
RETURN
DGPS 3D
Route contents display
Save route menu
3. Press the NEW soft key to show the new
route window.
6. Press the [PLOT] key to show the plot
display. The SAVE icon appears at the
bottom of the screen.
NORTH
UP
Next consecutive route number
ROUTE NAME
006
ZOOM
SAVE
ROUTE
IN
ZOOM
OUT
START
LOG
COURSE
UP
COMMENT
DGPS 3D
CANCEL
DGPS 3D
SA
VE
NAV
POS
SAVE icon
SAVE icon appearance on the plotter display
New route window
6-5
6. ROUTES
7. Press the [SAVE/MOB] key with a
touch-and-release action to enter a
waypoint mark at own ship position. A
new waypoint is created under the next
consecutive waypoint number and that
waypoint is added to the route.
8. Repeat step 7 whenever you change
course. 35 waypoints can be entered.
9. To stop creating the track-based route,
press the [WPT/RTE] key followed by the
CREATE VOYAGE BASED ROUTE soft
key.
10. Press the FINISH LOG soft key to
register the route. The SAVE icon
disappears.
6.5
Erasing Routes
1. Press the [WPT/RTE] key followed by the
ROUTES soft key to open the route
menu.
2. Press ▲ or ▼ to select a route you want
to erase.
3. Press the ERASE ROUTE soft key. You
are asked if you are sure to erase the
route.
4. Press the [ENTER] key to erase the
route.
6-6
7. NAVIGATION
7.1
Navigating to “Quick
Points”
The “quick point” feature allows you to
navigate to point(s) without retaining the data
indefinitely in your unit’s memory. Each time
a quick point is entered previous quick points
have the same numbers as newly entered
ones are written over.
A light-blue line connects between own ship
and destination, marked “QP<01>”, and it
shows the shortest course to the destination.
Arrows on the line show the direction to
follow to get to the quick point. Range and
bearing from own ship to the destination
appear at the top of screen. This location is
saved to the waypoint list as waypoint
“QP01.”
Selecting quick point entry method
You need to tell your unit how to set the
quick point: 1 POINT, 35 POINT (up to 35
points) or WPT/PORT SERV. (For
WPT/PORT SERV, see the next page.)
1. Press the [MENU] key.
2. Press the DISPLAY OPTIONS soft key.
3. Select SET GO TO METHOD and press
the EDIT soft key. The following display
appears.
SET GO TO METHOD
1 POINT
35 POINT
WPT/PORT SER
SET GOTO METHOD window
4. Select method desired.
5. Press the ENTER soft key.
6. Press the RETURN soft key to finish.
Navigating to a single quick point
1. Select 1 POINT in “Selecting quick point
entry method,” and return to the plotter
display.
2. Place the cursor on an existing waypoint
(GO TO WPT soft key appears) or a new
location (GO TO CURSOR soft key
appears).
3. Depending on the selection you made at
step 2, press the GO TO CURSOR or
GO TO WPT soft key.
Navigating to multiple quick points
1. Select 35 POINT in “Selecting quick point
entry method,” and return to the plotter
display.
2. Press the GO TO soft key.
3. Place the cursor on an existing waypoint
(SELECT WPT soft key appears) or a
new location (ADD QP soft key appears).
4. Depending on the selection you made at
step 3, press the SELECT WPT or ADD
QP soft key. “QP<01>” appears at the
cursor location. To erase last-entered
waypoint, press the ERASE LST WPT
soft key.
5. Repeat steps 3 and 4 to enter other quick
points.
6. After entering all waypoints (up to 35
points), press the [ENTER] key to
register the route.
A light-blue line connects between own ship
and all quick points, and it shows the
shortest course to destination. Arrows on the
line show the direction to follow the route.
Quick points are numbered in sequential
order from QP<01> and are saved to the
waypoint list. Range and bearing from own
ship to the first destination appear at the top
of screen. The unit saves the points as a
route, under the name “Q<RTE” (Quick
Route).
7-1
7. NAVIGATION
7.2
Navigating to Waypoints
(waypoint list)
1. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
2. Press the WAYPOINTS soft key to open
the WAYPOINTS menu.
3. Press the LOCAL LIST or
ALPHA/NUMERIC LIST soft key to show
corresponding waypoint list.
4. Select a waypoint.
5. Press the GO TO soft key. The plotter
display appears. A light-blue line runs
between destination selected and own
ship’s position. Arrows on the line show
the direction to follow. Waypoint data
appear at the top of screen.
7.3
Navigating to Ports, Port
Services
Some Nav-ChartsTM and C-MAP chart cards
have a port service list which shows services
available at ports or harbors. (See page 2-5.)
You can use the list to set destination as
follows:
1. Press the [MENU] key to open the main
menu.
2. Press the DISPLAY OPTIONS soft key.
3. Press ▼ to select SET GO TO METHOD
and press the EDIT soft key.
4. Press the ▲ or ▼ to select WPT/PORT
SER and press the [ENTER] key or the
ENTER soft key.
5. Press the [PLOT] key to return to the
plotter display.
6. Press the GO TO soft key. Soft key titles
change as in the figure below.
+ 40°45.971'N
13°57.462'E
FROM
OS
0.26 nm
180.2°
GO TO
QUICK
ROUTE
NEAR
SRVICE
PUNTA CORNACCHIA
ACCO AMENO
PORT
ISCHIA PORTO
CASAMICCIOLA
I. ISCHIA
DGPS 3D
CANCEL
GO TO
Plotter display
7. Press the PORT or NEAR SRVICE soft
key depending on objective. PORT
shows a list of ports in your area. NEAR
SRVICE displays the port service list.
SELECT PORT
ACCIAROLI
ACQUAMORTA
AGNONE S. NICOLA
AGROPOLI
AMALFI
BAIA
CAPRI
CASA MICCIOLA-ISCHIA
Sample port list (southern Italy)
7-2
7. NAVIGATION
+
SELECT PORT
SERVICE
40°45.971'N
13°57.462'E
FROM
OS
0.26 nm
180.2°
GO TO
PUNTA CORNACCHIA
ACCO AMENO
ENTER
ISCHIA PORTO
CASAMICCIOLA
I. ISCHIA
DGPS 3D
CANCEL
GO TO
Sample filling station locations
(southern Italy)
▼
Sample port service list
8. If you selected PORT at step 7, use the
cursor pad to select a port and press the
[ENTER] key. Make a route using the soft
keys and press the [ENTER] key. (If you
want to go directly to that port, simply
press the ADD QP soft key followed by
the [ENTER] key.)
If you selected NEAR SERVICE in step
7, select service mark desired and then
press the ENTER soft key. Then, the
display shows the locations of those
services nearest you. (The figure at right
shows the location of filling stations in an
area in southern Italy.) Use ▲ or ▼ to
place the “hand cursor” on the port
service icon desired and press the
ENTER soft key. Make a route using the
soft keys and press the [ENTER] key. (If
you want to go directly to location
selected, simply press the ADD QP soft
key followed by the [ENTER] key.)
7-3
7. NAVIGATION
7.4
Navigate along specific leg of route
Following a Route
1. Press the [WPT/RTE] key followed by the
ROUTE soft key to open the route list.
2. Press ▲ or ▼ to select a route.
3. Press the GO TO soft key to show the
plotter display.
FISH
WPT
FROM
OS
1.3 nm
208.5°
GO TO
ROUTE
ZOOM
IN
ZOOM
OUT
WP-002
GO TO
WPT
FISH
RVSE
ROUTE
WP-001
DGPS 3D
Place the cursor on the leg to display it in a
white and red flashing line, and then press
the FOLLOW LEG soft key.
Restarting navigation
When you steer to avoid an obstacle or the
vessel drifts, you may go back your intended
course (Line 1 in the figure below). Use the
steering or highway display to help you
return to course.
Also, if you don’t need to return to the
original course, you can go directly to the
waypoint (Line 2 in the figure below) using
the restart function below.
RETURN
CRAB
Line 2
Plotter display, route selected as destination
The cursor is on the route waypoint nearest
own ship.
4. Operate the cursor pad to place the
cursor on the waypoint or leg desired in
the route.
5. Press the GO TO WPT or FOLLOW LEG
soft key (depending on the choice made
at step 4).
Green lines connect all route waypoints and
arrows on the lines point in the direction to
traverse the route.
Obstacle
Original course
Example of when to restart navigation
1. Set a destination.
2. Press the [WPT/RTE] key to open the
WAYPOINT & ROUTE menu.
3. Press the LOG soft key.
TO Waypoint (WPT no. in reverse video)
Passed waypoint (gray characters)
Estimated Time of Arrival at last
waypoint
Navigate route waypoints in reverse
order
Press the RVSE ROUTE soft key to reverse
the order to traverse waypoints. The arrows
on the route line point in the direction
selected.
ETA
01
BRIDGE
02
HARBOR
03
WP<001>
04
Navigate directly to a route waypoint
WP<002>
05
WP<003>
If you want to go directly to a route waypoint,
place the cursor on the waypoint to show the
flashing diamond, and then press the GO TO
WPT soft key.
Line 1
LOG
23:59 31.SEP
34°23.564'N
135°23.456'E
34°32.456'N
135°32.456'E
34°23.345'N
135°12.456'E
34°34.555'N
135°55.555'E
34°32.555'N
134°99.999'E
LEG
120.5°
23.4nm
23.6°
23.4nm
STOP
123.6°
23.5nm
RVSE
ROUTE
180.5°
23.5nm
SPEED
180.5°
23.5nm
COORD
TYPE
DGPS 3D
Log display
4. Press the RESTART soft key.
7-4
RESTART
7. NAVIGATION
Setting speed for ETA calculation
Switching waypoints
Speed, which may be input manually or
automatically, is required to calculate ETA
(Estimated Time of Arrival) to a waypoint.
When you arrive to a waypoint on a route,
you can switch to the next waypoint three
ways: AUTO1, AUTO2 and MANUAL.
1. Press the [WPT/RTE] key to display the
WAYPOINT & ROUTE menu.
2. Press the LOG soft key.
3. Press the SPEED soft key.
AUTO1: Automatically switches the TO
waypoint when your boat is within the arrival
alarm area. For how to set the arrival alarm
area, see “9.3 Arrival Alarm” on page 9-2.
SELECT SPEED
FOR ETA
Waypoint
▲
▼
SPD 10.0kt
GPS AVG SPD
Select speed for ETA window
Own Ship
Swithes to the next waypoint here.
Auto 1
4. Key in speed manually in the SPD field,
or use GPS speed data by selecting GPS
AVG SPD.
5. Press the ENTER soft key to register
your selection.
AUTO2: Automatically switches the TO
waypoint when the boat enters the arrival
alarm range or the boat passes an imaginary
perpendicular line passing through the
center of the destination waypoint.
Switches to the next waypoint
on the perpendicular though own
ship is off the arrival alarm range.
Own ship
Waypoint
Perpendicular
Auto 2
MANUAL: When the boat enters the arrival
alarm area, the TO waypoint may be
switched by using the RESTART soft key (on
the LOG display). If the arrival alarm is not
set, the waypoint will not be switched. To be
alerted when you arrive at a waypoint turn on
the audio alarm. For further details, see “9.2
Audio Alarm On/Off” on page 9-1.
7-5
7. NAVIGATION
To select waypoint switching method do the
following:
1.
2.
3.
4.
Press the [MENU] key.
Press the DISPLAY OPTIONS soft key.
Select WAYPOINTS SW.
Press the EDIT soft key to show the
waypoint sw window.
WAYPOINTS SW
AUTO 1
AUTO 2
MANUAL
Waypoint sw window
5. Select appropriate waypoint switching
method.
6. Press the ENTER soft key to close the
window.
7.5
1.
2.
3.
4.
5.
6.
Canceling Navigation
Press the [WPT/RTE] key.
Press the LOG soft key.
Press the STOP soft key.
Press the [ENTER] key to go stand by.
Press the RELEASE soft key.
Press the [ENTER] key.
7-6
8. PLOTTER ALARMS
8.1
Introduction
There are five plotter-related alarms which
generate both audible and visual alarms:
Arrival alarm, Anchor Watch alarm, XTE
(Cross Track Error) alarm, Proximity alarm,
and Speed alarm.
When an alarm setting is violated the buzzer
sounds, and the speaker icon ( ) appears
in red. You may silence the alarm by
pressing the [CLEAR] key. The icon remains
on the screen until the cause of the alarm is
removed or the alarm is deactivated.
8.2
Audio Alarm On/Off
The audio alarm sounds whenever an alarm
setting is violated. You can enable or disable
the audio alarm as follows:
1. Press the [ALARM] key to show the
ALARM menu.
ALARM
AUDIO ALARM
ARRIVAL ALARM
ANCHOR ALARM
PROXIMITY ALARM
XTE ALARM
SPEED ALARM
ON
ON 0.100nm
ON 0.050nm
ON
ON 0.100nm
OVER/UNDER
12.5 ~ 15.0kt
EDIT
CLEAR
ALARM
ALARM INFORMATION
NO ALARM
DGPS 3D
Alarm menu
2. Press ▲ or ▼ to select AUDIO ALARM.
3. Press the EDIT soft key to show the
audio alarm window.
AUDIO ALARM
▲
▼
ON
OFF
Audio alarm window
4. Press ▲ or ▼ to select ON or OFF.
5. Press the ENTER soft key or the
[ENTER] key to register your selection.
8-1
8. PLOTTER ALARMS
8.3
Arrival Alarm
8.4
The arrival alarm informs you that your boat
is approaching a destination waypoint. The
area that defines an arrival zone is that of a
circle which you approach from the outside
of the circle. The alarm will be released if
your boat enters the circle. When the arrival
alarm is active, a red dashed circle marks
the arrival alarm area.
Anchor Watch Alarm
The anchor watch alarm informs you that
your boat is moving when it should be at rest.
When the anchor watch is active, a red
dashed circle marks the anchor watch area.
Alarm
setting
Alarm
range
Your ship's position
where you start the
anchor watch alarm.
Own ship
: Alarm area
Destination
waypoint
How the arrival alarm works
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select ARRIVAL
ALARM.
3. Press the EDIT soft key to show the
arrival alarm window.
: Alarm
area
How the anchor watch alarm works
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select ANCHOR
ALARM.
3. Press the EDIT soft key to open the
anchor alarm window.
ANCHOR ALARM
▲
ARRIVAL ALARM
▼
▲
▼
ON 0.500nm
OFF
Arrival alarm window
4. Press ▲ to select ON.
5. Operate the cursor pad to place the
cursor on the digit desired.
6. Key in the alarm range desired. The
arrival alarm range is 0.001 to 9.999
miles.
7. Press the ENTER soft key or the
[ENTER] key.
8-2
ON 0.050nm
OFF
Anchor watch alarm window
4. Press ▲ to select ON.
5. Key in the alarm range desired. The
anchor watch range is 0.001 to 9.999
miles.
6. Press the ENTER soft key or the
[ENTER] key to register your selection.
The anchor alarm range appears with the
circle, its center is the own ship location
when pressing the [ENTER] key. If own ship
goes out this range, the alarm works.
8. PLOTTER ALARMS
8.5
XTE (Cross Track Error)
Alarm
3. Press the EDIT soft key to display the
speed alarm window.
The XTE alarm warns you when your boat is
off its intended course. When the XTE alarm
is active, two red dashed lines mark the XTE
alarm area.
SPEED ALARM
▲
▼
Alarm
setting
Own ship's
position
Speed alarm window
Destination
waypoint
: Alarm
How the XTE alarm works
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select XTE ALARM.
3. Press the EDIT soft key to open the XTE
alarm window.
XTE ALARM
▲
ON 0.100nm
OFF
▼
WITHIN 15.0 ~ 15.3
OVER/UNDER
kt
OFF
4. Press ▲ or ▼ to select WITHIN or
OVER/UNDER.
5. Key in the alarm range desired.
6. Press the ENTER soft key or the
[ENTER] key to finish.
8.7
Proximity Alarm
The proximity alarm alerts you when your
vessel nears a waypoint by the distance set
for that waypoint on the waypoint list. This
distance is called the proximity alarm radius.
The waypoint having a proximity alarm
. You can globally
radius is displayed with
activate or deactivate the proximity alarm
here.
XTE alarm window
4. Press ▲ to select ON.
5. Key in the alarm range desired. The XTE
alarm range is 0.001 to 9.999 miles.
6. Press the ENTER soft key or the
[ENTER] key to register your selection.
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select PROXIMITY
ALARM.
3. Press the EDIT soft key to show the
proximity alarm window.
PROXIMITY ALARM
8.6
Speed Alarm
The speed alarm warns you when your
boat’s speed is within, over/under or under
the speed range set.
1. Press the [ALARM] key to open the alarm
menu.
2. Press ▲ or ▼ to select SPEED ALARM.
▲
▼
ON
OFF
Proximity alarm window
4. Select ON or OFF by the cursor pad.
5. Press the ENTER soft key or the
[ENTER] key to register your selection.
8-3
8. PLOTTER ALARMS
8.8
Alarm messages
Alarm Information
When an alarm setting has been violated the
buzzer sounds and the speaker icon (shown
in red) appears. You can see which alarm
has been violated, as well as silence the
buzzer, on the alarm menu display.
1. Press the [ALARM] key.
AUDIO ALARM
ARRIVAL ALARM
ANCHOR ALARM
PROXMTY ALARM
XTE ALARM
SPEED ALARM
ON
ON 0.100nm
ON 0.050nm
ON
ON 0.100nm
OVER/UNDER
12.5 ~ 15.0kt
ALARM INFORMATION
ALARM
EDIT
CLEAR
ALARM
YOU HAVE ARRIVED AT
WAYPOINT : SP-001.
DGPS 3D
Alarm information
(Example: Arrival alarm)
Alarm menu
2. Press the CLEAR ALARM soft key to
silence the buzzer. The color of the alarm
message and the speaker icon changes
from red to black.
Note: The speaker icon is displayed in red
until all alarms have been
acknowledged on the alarm menu
display. If more than one alarm has
been violated the message
CONTINUE appears at the bottom of
the display. In this case press the
NEXT INFO soft key to see which
other alarms have been violated.
8-4
Alarm messages and their meanings
Message
Meaning
YOU HAVE ARRIVED
AT WAYPOINT.
Arrival alarm setting
violated.
YOU HAVE EXCEEDED
ANCHOR WATCH
LIMIT.
Anchor watch alarm
setting violated.
YOU HAVE ENTERED
AN AVOIDANCE AREA.
Proximity alarm
setting violated.
YOU HAVE EXCEEDED
XTE LIMIT.
XTE alarm setting
violated.
YOU HAVE EXCEEDED
SPEED ALARM LIMIT.
Speed alarm setting
violated.
9. MEMORY CARD OPERATIONS
The following data can be saved to memory
cards:
9.1
• Mark/line
Before you can use a memory card it must
be formatted. Note that formatting a used
card erases all saved data.
• Waypoints/routes
• Track
• Configuration (menu settings)
Formatting Memory
Cards
1. Turn the power off.
2. Insert the memory card you want to
format into the slot.
3. Turn the power on.
4. Press the [MENU] key followed by the
CONFIGURATION and
UPLOAD/DOWNLOAD DATA soft keys.
DWNLOAD
UPLOAD
DOWN WPT/RTE TO PC
UPLOAD WPT/RTE FROM PC
SAVE DATA TO MEMORY CARD
LOAD DATA FROM MEMORY CARD
DGPS 3D
RETURN
Download/upload menu
5. Press the SAVE DATA TO MEMORY
CARD
TRACK
OFF
SAVE
DATA
MARK/LINE
OFF
EDIT
WAYPOINT/ROUTE OFF
CONFIGURATION
SAVE
DATA
OFF
FORMAT
RETURN
DGPS 3D
Save data display
6. Press the FORMAT soft keys. You are
asked if you are ready to format the
memory card.
9-1
9. MEMORY CARD OPERATIONS
7. Press the [ENTER] key to format (or
press the [CLEAR] key to escape). Now
FORMATTING MEMORY CARD appears.
Do not remove the card while it is being
formatting. When the formatting is
completed, FORMAT COMPLETED
appears.
8. Press the [ENTER] key to finish. Now
you can record data to the memory card.
Note: Chart cards cannot be formatted.
9.2
Saving Data to Memory
Card
The memory card can save four items of
data; track, mark/line, waypoint/route and
configuration.
Saving data
1. Insert a formatted memory card into the
slot.
2. Press the [MENU] key followed by the
CONFIGURATION and
UPLOAD/DOWNLOAD DATA soft keys.
3. Press the SAVE DATA TO MEMORY
CARD soft key. The SAVE DATA display
appears.
4. Press ▲ or ▼ to select item to save.
5. Press the EDIT soft key to open the
TRACK, MARK/LINE,
WAYPOINTS/ROUTES or
CONFIGURATION window.
6. Press ▲ to select ON.
7. Press the ENTER soft key or the
[ENTER] key.
8. Repeat steps 4 to 7 to save other data if
desired.
9. Press the SAVE DATA soft key. The
following message appears and saving
starts. Do not remove the memory card
while data is being saved.
NOW SAVING DATA TO
MEMORY CARD. DO NOT
TURN OFF THE POWER UNTIL
SAVING COMPLETED.
SAVE DATA message
When saving is completed, COMPLETE
SAVING DATA appears.
10. Press the [ENTER] key.
9-2
9. MEMORY CARD OPERATIONS
Error messages
Memory card not inserted
Press the [ENTER] key to return to the SAVE
DATA display.
MEMORY CARD NOT
INSERTED. INSERT CARD
PRESS "ENTER" key
TO CONTINUE.
Not inserted message
Unformatted memory card
Press the [ENTER] key to return to the SAVE
DATA display. And format it refering to the
previous page.
MEMORY CARD NOT
FORMATTED
PRESS "ENTER" key
TO CONTINUE.
Not formatted message
9.3
Loading Data from
Memory Card
Data (track, marks, waypoints, configuration)
can be loaded from a memory card and
displayed on the screen. This feature is
useful for observing past data and setting up
the equipment for a specific purpose (with
“configuration”).
1. Press the [MENU] key followed by the
soft keys CONFIGURATION and
UPLOAD/DOWNLOAD DATA.
2. Press the LOAD DATA FROM MEMORY
CARD soft key to show the LOAD DATA
display.
TRACK
OFF
LOAD
DATA
MARK/LINE
OFF
EDIT
WAYPOINT/ROUTE OFF
CONFIGURATION
LOAD
DATA
OFF
Wrong card inserted
When a wrong card is inserted, the following
error message appears. Press the [ENTER]
key to return to the SAVE DATA display.
Replace it with a formatted memory card.
WRONG CARD INSERTED.
INSERT MEMORY CARD.
PRESS "ENTER" key
TO CONTINUE.
Wrong card message
Data overwrite
Data type to be recorded exists on memory
card. (Two or more of same data type cannot
be recorded.) Press the [ENTER] key to
overwrite same data type on the card, or
press the [CLEAR] key to escape.
RETURN
DGPS 3D
Load data display
3. Press ▲ or ▼ to select item to load.
4. Press the EDIT soft key to show the
ON/OFF selection window.
5. Press ▲ to select ON. Press the ENTER
soft key or the [ENTER] key. If the
memory card does not contain the item
selected, the buzzer sounds and ON
cannot be selected.
6. After you select all items desired, press
the LOAD DATA soft key to load data.
The following message appears.
OVERWRITE FOLLOWING
DATA. OK?
(TRACK)
YES ... "ENTER" key
NO ... "CLEAR" key
Overwrite message
9-3
9. MEMORY CARD OPERATIONS
NOW LOADING DATA FROM
MEMORY CARD. DO NOT
TURN OFF THE POWER UNTIL
LOADING COMPLETE.
Load data message
After loading is completed, the following
message appears.
COMPLETE LOADING DATA.
PRESS "ENTER" KEY
TO CONTINUE.
Complete message
7. Press the [ENTER] key.
Notes on loading data
Track
Since loaded track data is added to internal
track, oldest track in the memory of the unit
will be deleted when the track memory
capacity is exceeded.
Waypoint/route
Waypoints/routes in the memory of the unit
are deleted to make room for loaded ones.
Mark/line
The loaded data is added to internal data.
When the mark/line memory becomes full,
no marks may be entered.
Configuration
The loaded data replaces current
configuration settings. Press the [ENTER]
key to restart. If the memory card is ejected
while loading, or data could not be loaded,
press the [ENTER] key to restart with default
settings. Note that the track memory
capacity setting is not saved nor loaded.
9-4
10. CUSTOMIZING YOUR UNIT
This section describes the various options
which allow you to set up your unit to suit
your needs.
10.1 CHART SETUP
OPTIONS menu
The chart offset options menu provides three
menus: chart offset, track control, and chart
details.
1. Press the [MENU] key to open the main
menu.
2. Press the CHART SETUP OPTIONS soft
key.
CHART OFFSET menu
In some instances position may be off by a
few minutes. For example, the position of the
ship is shown to be at sea while it is in fact
moored at a pier. You can compensate for
this error by offsetting chart position as
follows:
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and CHART
OFFSET soft keys.
34° 12.345' N
135° 12.345' E
FROM 16.41 nm
276.9°
OS
CHART
OFFSET
ZOOM
IN
ZOOM
OUT
CHART
SETUP
SET
OFFSET
RESET
OFFSET
CHART OFFSET
TRACK CONTROL
DGPS 3D
RETURN
CHART DETAILS
Plotter display, chart offset selected
DGPS 3D
RETURN
Chart setup options menu
2. Use the cursor pad to place the cursor
where to offset chart position.
3. Press the SET OFFSET soft key.
4. Press the RETURN soft key to finish.
To cancel chart offset, press the RESET
OFFSET soft key at step 3 in the above
procedure.
TRACK CONTROL menu
This menu mainly controls track color and
track plotting interval. For further details see
Chapter 3.
10-1
10. CUSTOMIZING YOUR UNIT
CHART DETAILS menu
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and CHART
DETAILS soft keys.
LAT/LON GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
OFF
WHITE
STD
CHART
DETAIL
EDIT
DEPTH
INFO
RETURN
DGPS 3D
Chart details menu
2. Use the cursor pad to select item and
press the EDIT soft key.
3. Select option with the cursor pad and
press the RETURN soft key to finish.
Chart details menu description
LAT/LONG GRID: Turns lat/long grid on/off
and changes its color.
TEXT INFO: Turns geographic name display
on/off.
WAYPOINT: Turns waypoint on or off and
selects size to large or small. “LARGE”
displays waypoint in shape selected;
“SMALL” shows waypoints as an X
regardless of actual shape. “OFF” only
display waypoints when they are used in
navigation.
WAYPOINT NAME: Turns waypoint name
on/off.
INDEX: Turns chart indices on/off.
10-2
LANDMASS: Selects brightness and color of
land.
BACKGROUND: Selects background color
to black or blue.
NAV AIDS: Turns aids to navigation symbols
(for example, buoys) on/off. When OFF is
selected, symbols are displayed but
information is not.
SECTOR INFO: Turns lighthouse viewable
angle indication (on FURUNO charts) on/off.
Viewing angle is shown as an arc extending
from lighthouse position. Arc color, white or
green, is the color of the light beam. This
feature is available with selected charts.
OTHER SYMBOLS: Selects color of all
other chart symbols.
MARK SIZE: Selects the mark size STD
(standard) or SMALL (appearing with “x”.)
DEPTH INFO soft key: Turns depth info
display on/off and sets it color.
10. CUSTOMIZING YOUR UNIT
10.2 DISPLAY OPTIONS
menu
This menu contains items for setting up the
plotter displays.
1. Press the [MENU] key.
2. Press the DISPLAY OPTIONS soft key.
The display setup1 menu appears.
RNG & BRG MODE
RANGE/SPEED UNIT
DEPTH UNIT
TEMP UNIT
LAT/LON DISPLAY
TIME DISPLAY
WAYPOINTS SW
COURSE VECTOR
BEARING
MAG VARIATION
TD DISPLAY
POSITION DISPLAY
SET GO TO METHOD
OPERATION MODE
LANGUAGE
RHUMB LINE
nm / kt
ft
°F
DD°MM.MMM'
24 HOUR
AUTO2
LINE
MAGNETIC
AUTO 01.3°E
LORAN C
LAT/LON
1 POINT
PLEASURE
ENGLISH
DISPLAY
SETUP
EDIT
Selects unit of water temperature
measurement between Celsius and
Fahrenheit.
LAT/LON DISPLAY
Displays the minutes of latitude and
longitude positions in hundredths,
thousandths or ten thousandths.
TIME DISPLAY
Selects time display format for 12 hour or 24
hour.
WAYPOINT SW
RETURN
DGPS 3D
TEMP UNIT
Display setup menu
DISPLAY SETUP menu description
RNG & BRG MODE
The GPS receiver calculates the range,
bearing, cross track error (XTE) and ETA to
TO waypoint when you set a destination.
The range and bearing can be calculated by
GREAT CIRCLE (straight line between two
points) or RHUMB LINE (straight line
between two points on nautical chart)
method.
RANGE/SPEED UNIT
Selects the unit for range and speed; nm/kt,
km/ km/h, sm/ sm/h.
DEPTH UNIT
Selects unit of depth measurement among
feet, fathoms, and meters.
Provides automatic or manual waypoint
switching when following a route. For further
details, see page 7-5.
COURSE VECTOR
You may extend a line from the own ship
position to show ship’s course. The line can
be a vector (the length depends on the ship’s
speed) or course bar (course bar).
BEARING
A navigation device outputs both true and
magnetic bearings. A magnetic bearing is
true bearing plus (or minus) earth’s magnetic
deviation. Thus the equation for finding
magnetic bearing is;
true bearing ±x (magnetic variation)° =
magnetic bearing
You can display your ship’s course and
bearing to waypoint in true or magnetic
bearing.
10-3
10. CUSTOMIZING YOUR UNIT
MAG VARIATION
The magnetic variations for all areas of the
earth are preprogrammed into this unit. The
preprogrammed variation is accurate for
most instances, however you may wish to
manually enter a updated variation referring
the latest navigation chart.
1. Select MAG VARIATION, and press the
EDIT soft key to show the mag variation
window.
MAG VARIATION
▲
▼
AUTO
MANUAL 0.7°W
OPERATION MODE
Selects the operation mode among
PLEASURE, FISHING 1 and FISHING 2.
For details, see page 4-1 and 5-1.
LANGUAGE
Selects the language for operation display
for ENGLISH or FRENCH.
10.3 GPS/DGPS/TD OPTIONS
menu
This menu sets up GPS and DPGS receivers
and enables display of position in Loran C or
Decca TDs.
Mag variation window
2. Select MANUAL.
3. Key in magnetic deviation value.
4. Press the W<-->E soft key to switch
between East and West and vice versa, if
necessary.
5. Press the ENTER soft key or the
[ENTER] key to finish.
1. Press the [MENU] key.
2. Press the GPS/DGPS/TD OPTIONS soft
key to display the GPS/DGPS/TD options
menu.
GPS/DGP
OPTION
GPS SETUP OPTIONS
DGPS/WAAS SETUP OPTIONS
TD SETUP
TD DISPLAY
Position may be shown in Loran C TDs,
Decca TDs, or latitude and longitude. To
display position in TDs, select Loran C or
Decca here and choose TD at “POSITION
DISPLAY” below. You can select the Loran C
or Decca chain to use on the TD SETUP
menu. For details see “TD SETUP menu” on
page 10-7 and 8.
POSITION DISPLAY
Displays position in latitude and longitude or
TD (time difference).
SET GO TO METHOD
Selects the method for entering the quick
point: 1 POINT, 35 POINT (2-35 points), or
WPT/PORT SER. For further details see
pages 7-1 and 7-2.
10-4
DGPS 3D
RETURN
GPS/DGPS/TD options menu
10. CUSTOMIZING YOUR UNIT
GPS SETUP OPTIONS menu
description
This menu provides items for setting up the
GPS receiver. To display it, display the menu
shown above, and then press the GPS
SETUP OPTIONS soft key.
GPS
OPTION
LOCAL TIME OFFSET
GEODETIC DATUMS
POS SMOOTHING
SPD/CSE SMOOTHING
GPS SPEED AVE
LAT OFFSET
LON OFFSET
DISABLE SATELLITE
LATITUDE
LONGITUDE
ANT. HEIGHT
FIX MODE
+00:00
WGS-84
000 sec
005 sec
060 sec
0.000'N
0.000'E
__ __ __
38°00.000'N
123°00.000'W
005 m
2D/3D
DGPS 3D
EDIT
RETURN
GPS SETUP options menu
LOCAL TIME OFFSET
GPS uses UTC time. If you would rather use
local time, enter the time difference between
it and UTC time. Use the +<-->- soft key to
switch from plus to minus and vice versa.
GEODETIC DATUM
Your equipment is preprogrammed with most
of the major chart systems of the world.
Although the WGS-84 system, the GPS
standard, is now widely used other
categories of charts still exist. Select the
chart system used, not the area where your
boat is sailing. The default chart system is
WGS-84.
1. Select GEODETIC DATUM.
2. Press the EDIT soft key to show the
geodetic datum window.
3. Press ▲ or ▼ to select the chart system
you are using. If UNKNOWN appears in
the GEODETIC DATUM window, select a
different chart system.
4. Press the ENTER soft key or the
[ENTER] key to register your selection.
POS SMOOTHING
When the DOP or receiving condition is
unfavorable, the GPS fix may change, even
if the vessel is dead in water. This change
can be reduced by smoothing the raw GPS
fixes. A setting between 000 to 999 is
available. The higher the setting, the more
smoothed the raw data, however too high a
setting slows response time to change in
latitude and longitude. This is especially
noticeable at high ship’s speeds. 000 is the
normal setting; increase the setting if the
GPS fix changes.
SPD/CSE SMOOTHING
During position fixing, ship’s velocity (speed
and course) is directly measured by
receiving GPS satellite signals. The raw
velocity data may change randomly
depending on receiving conditions and other
factors. You can reduce this random
variation by increasing the smoothing. Like
with latitude and longitude smoothing, the
higher the speed and course smoothing the
more smoothed the raw data. If the setting is
too high, however, the response to speed
and course change slows. For no smoothing,
enter all zeroes. The default setting is 005
(sec).
GEODETIC DATUM
▲
AUSTRALIA
▼
CHART DATUM
WGS-84
Geodetic datum window
10-5
10. CUSTOMIZING YOUR UNIT
GPS SPEED AVE
Calculation of ETA is based on average
ship’s speed over a given period. If the
period is too long or too short calculation
error will result. Change this setting if
calculation error occurs. The default setting
is 60 seconds, which is suitable for most
conditions.
LAT OFFSET, LON OFFSET
GPS-generated position may be off from the
chart. In this case, you can apply an offset to
GPS position to refine position accuracy.
Mark the equipment indication on the chart,
and then calculate the L/L error.
1. Select LAT OFFSET or LON OFFSET.
2. Press the EDIT soft key.
3. Key in the error value. To switch the
north and south (east and west), press
the N<->S (W<->E) soft key.
4. Press the ENTER soft key or [ENTER]
key.
DISABLE SATELLITE
Every GPS satellite is broadcasting
abnormal satellite number(s) in its Almanac,
which contains general orbital data about all
GPS satellites, including those which are
malfunctioning. Using this information, the
GPS receiver automatically eliminates any
malfunctioning satellite from the GPS
satellite schedule. However, the Almanac
sometimes may not contain this information.
If you hear about a malfunctioning satellite
from another source, you can disable it
manually. Enter satellite number (max. 3
satellites) in two digits and press the ENTER
soft key or the [ENTER] key.
LATITUDE, LONGITUDE
The default latitude and longitude position is
San Francisco, USA (38.00.000’N,
123.00.000’W). When the unit is turned on
for the first time it begins searching for its
actual position. To lessen the time required
10-6
to find position, you may enter your position
manually. To switch from North to South and
vice versa, use the N<-->S soft key, and to
switch from West to East and vice versa, use
the W<-->E soft key. Finally, press the
ENTER soft key or the [ENTER] key.
ANT. HEIGHT
Enter the height of the antenna unit above
sea surface. For further details refer to the
Installation Manual.
FIX MODE
You can choose the position-fixing mode
from 2D or 2D/3D. 2D requires three
satellites to fix position; 2D/3D requires three
or four satellites, whichever is available.
DGPS/WAAS SETUP OPTIONS menu
This menu sets parameters for the DGPS
beacon receiver. (GP1650WD, or GP1650W
equipped with DGPS beacon receiver.) and
WAAS. To display it, press the [MENU] key
followed by the GPS/DPGS/TD OPTIONS
and DGPS SETUP OPTIONS soft keys.
DGPS
WAAS
DGPS/WAAS MODE
AUTO
BEACON FREQUENCY
AUTO
BEACON BAUD RATE
AUTO
WAAS SEARCH
AUTO
EDIT
CORRECTIONA DATA SET 02
DGPS/WAAS ALARM
ON
DGPS 3D
RETURN
DGPS/WAAS menu
DGPS/WAAS MODE
Select DGPS, WAAS or AUTO. (Position is
fixed by WAAS when DGPS correction data
is not available.)
BEACON FREQUENCY (for DGPS)
DGPS reference station can be searched
automatically or manually. For manual
10. CUSTOMIZING YOUR UNIT
search, select MANUAL here, and use the
cursor pad to select frequency of DGPS
reference station. The default setting is
AUTO.
BEACON BAUD RATE (for DGPS)
Selects the transmission rate of the DGPS
reference station nearest you, among
AUTO (default setting), 50, 100 or 200 bps.
This setting is only effective when DGPS
mode is “manual”; baud rate cannot be
changed in automatic DGPS mode.
WAAS SEARCH (for WAAS)
Choose AUTO for automatic search or
MANUAL for manual search. For MANUAL,
enter appropriate WAAS satellite number,
referring to the illustration below.
AUTO mode and GEO satellite (in JUNE 2002)
118°W
2°
34.75°W
2°
24.5°E
2°
121.25°E
2°
120
131
134
AOR-W
54°W
AOR-E
15.5°W
IOR
64.5°W
POR
178°E
This menu selects the Loran C or Decca
chain to use to display position in TDs. To
display it, press the [MENU] key followed by
the GPS/DPGS/TD OPTIONS and TD
SETUP soft keys.
TD
LORAN C
GRI
9940 11-27
U.S. WEST COAST
CORRECTION1
+000.0µs
CORRECTION2
+000.0µs
DECCA
DEC CHAIN
20 R-P
FRENCH
CORRECTION1
+00.00 lane
CORRECTION2
+00.00 lane
DGPS 3D
SETUP
EDIT
RETURN
TD setup menu
Displaying LORAN C TDs
1. Select GRI and press the EDIT soft key
to show the GRI & STA. PAIR window.
GRI & STA. PAIR
▲
9940
11-27
▼
▲
122
TD SETUP menu
U.S. WEST COAST
GRI & sta. pair window
One-degree threshold
Longitude Range
Satellite
120.25°E to 117°W
134
119°W to 33.75°W
122
35.75°W to 25.5°E
120
23.5°E to 122.25°E
131
CORRECTIONS DATA SET (for WAAS)
Determines how to use the WAAS signal,
currently in the test mode. Enter appropriate
two-digit numeric. Use “02” (default setting)
until the WAAS System changes from its
current “Testing Status” to “Operational
Status”.
2. Press ▲ or ▼ to select GRI code. Press
► to enable selection of station pair, and
then press ▲ or ▼ to select station pair.
See the Loran C chain list at the end of
this manual for GRI and station pairs.
3. Press the ENTER soft key or the
[ENTER] key to register your selection.
4. If necessary, you may enter a position
offset to refine Loran C position. Select
LORAN C CORRECTION1 or
CORRECTION2 and press the EDIT soft
key. Enter correction value and press the
ENTER soft key or the [ENTER] key. Use
the + <--> - soft key to switch from plus to
minus and vice versa.
DGPS/WAAS ALARM
This alarm alerts you by aural and visual
alarms when the WAAS/DGPS signal is lost.
10-7
10. CUSTOMIZING YOUR UNIT
Displaying DECCA TDs
10.4 CONFIGURATION menu
1. Select DEC CHAIN and press the EDIT
soft key to show the chain sta. pair
window.
The CONFIGURATION menu has facilities
for setting up data ports,
uploading/downloading data, diagnostic test,
demonstration mode setup, and memory
clearing.
▲
CHAIN STA. PAIR
▲
20
P-R
▼
FRENCH
Chain sta. pair window
1. Press the [MENU] key.
2. Press the CONFIGURATION soft key to
display the configuration menu.
CONFIG
2. Press ▲ or ▼ to select Decca chain
number. Press ► to enable selection of
lane, and then press ▲ or ▼ to select
lane pair (R: red, G: green and P: purple).
Refer to the Decca chain list at the end of
this manual.
3. Press the ENTER soft key or the
[ENTER] key to register your selection.
4. If necessary, you may enter position
offset to refine Decca position. Select
DECCA CORRECTION1 or
CORRECTION2 and press the EDIT soft
key. Enter correction value and press the
ENTER soft key or the [ENTER] key. Use
the + <--> - soft key to switch from plus to
minus and vice versa.
SETUP NMEA PORT 1
SETUP NMEA/DGPS PORT 2
UPLOAD/DOWNLOAD DATA
SYSTEM MENU
DGPS 3D
RETURN
Configuration menu
SETUP NMEA PORT 1 menu
description
This menu sets up DATA PORT 1 according
to the specifications of the equipment
connected to it. The menu can be displayed
by pressing the [MENU] key followed by the
CONFIGURATION and SETUP NMEA
PORT 1 soft key. For detailed information,
see the Installation Manual.
SETUP
PORT 1
FORMAT
NMEA0183
Ver2.0
LAT/LON FORMAT DD°MM.MMM'
EDIT
SELECT
SNTNC.
DGPS 3D
RETURN
Setup NMEA port 1 (or 2) menu
10-8
10. CUSTOMIZING YOUR UNIT
FORMAT
Selects NMEA0183 version 1.5 or 2.0. If you
are unsure of the version number, try both
equipment and choose the one which
outputs data correctly.
LAT/LON FORMAT (GGA only)
connector at the back of display unit. The
menu can be displayed by pressing the
[MENU] key followed by the
CONFIGURATION and
UPLOAD/DOWNLOAD DATA soft keys. For
detailed information, see the Installation
Manual.
DWNLOAD
UPLOAD
Selects the minute of latitude and longitude
positions in hundredths, thousandths or ten
thousandths.
DOWNLOAD WPT/RTE TO PC
SELECT SNTNC. soft key
SAVE DATA TO MEMORY CARD
This key enables/disables input/output of
data sentences.
LOAD DATA FROM MEMORY CARD
UPLOAD WPT/RTE FROM PC
RETURN
DGPS 3D
SETUP NMEA/DGPS PORT 2 menu
description
This menu should be set according to the
specifications of the equipment connected to
connectors PORT 2 (DGPS) at the rear of
the display unit. The menu can be displayed
by pressing the [MENU] key followed by the
CONFIGURATION and SETUP NMEA
PORT 2 soft keys. For detailed information,
see the Installation Manual.
Upload/download menu
ANT
XDR
DGPS
NMEA
+ 13GND
2
12-24
VDC
FORMAT
Selects data format of connected equipment;
NMEA0183 version 1.5, version 2.0,
RTCM104 (EXTRN), RTCM104 (INTRN) or
RTCM104 (OUTPUT). RTCM104 (INTRN) or
RTCM104 (OUTPUT) is for GP-1650WD
only.
LAT/LON FORMAT (GGA only)
This setting can be performed when
NMEA0183 Ver.1.5 or 2.0 is minute as the
FORMAT. It displays the seconds of latitude
and longitude positions in hundredths,
thousandths or ten thousandths.
UPLOAD/DOWNLOAD DATA menu
This menu allows you to upload waypoint
and route data to a PC or download the
same data from a PC, via the DGPS
Connect PC to DGPS.
Display unit, rear view
Set communication software on the PC as
follows:
Baud Rate:
4800 bps
Character Length: 8 bit
Stop bit:
1 bit
Parity:
None
X Control:
XON/XOFF
The following data can be
downloaded/uploaded between a personal
computer and this equipment:
• Waypoint data (In alphanumeric order)
10-9
10. CUSTOMIZING YOUR UNIT
• Route data (In order of route number)
• End of sentence
Note 1: There are two kinds of data for
route data: route data and route
comment data.
Note 2: DGPS position fix is not available
when uploading or downloading
data.
Download waypoint/route to PC
1. Connect the PC to the GP-1650W series
as shown on the next page.
2. Press the DOWNLOAD WPT/RTE TO
PC soft key. You are asked if you are
GP-1650WD/1650W
DGPS
1
2
3
4
5
6
7
NC
NC
RD (YELLOW)
NC
SD (RED)
SG (BLUE)
SHIELD
ready to download waypoints and routes.
3. Press the [ENTER] key to download.
Upload waypoint/route from PC
Note that all waypoint and route data stored
in this unit will be deleted when data is
uploaded.
1. Connect the PC to the GP-1650W series
as shown below.
2. Press the UPLOAD WPT/RTE FROM PC
soft key. You are asked if you are ready
to upload waypoints and routes.
3. Press the [ENTER] key to upload.
PC/AT
DSUB 9-pin
(EIA-574)
PC/AT
DSUB 25-pin
(EIA-232)
3 (TxD)
2 (TxD)
2
5
4
6
7
8
3 (RxD)
7 (GND)
4 (DTR)
5 (DSR)
6 (RTS)
20 (CTS)
(RxD)
(GND)
(DTR)
(DSR)
(RTS)
(CTS)
Connection of GP-1650WD/GP-1650W to PC
10-10
10. CUSTOMIZING YOUR UNIT
Waypoint data format
Route data menu
PFEC, GPwpl, llll.lll, a, yyyyy.yyy, a, c----c, c, c----c, A <CR><LF>
1 2
3
4
5
6 7
8
$GPRTE, x, x, a, ccc, c----c, c----c, ... , c----c <CR><LF>
5
1 2 3
4
6
12
Waypoint data format
Route data format
Waypoint latitude
N/S
Waypoint longitude
E/W
Waypoint name (Number of characters is
fixed to 6 and space code is placed when
the number of characters are less than
6.)
6: Waypoint color
7: Waypoint comment (1 byte for mark code
+ 13 characters of comment.)
1st byte of mark code: Fixed to ‘@’.
2nd byte of mark code: Internal mark
code. See Note 1.
8. Information of marking waypoint. Always
set to “A”.
“A”: Displayed
“V”: Not displayed
1: Number of sentences required for one
complete route data (1 to 4). See Note 2.
2: Number of sentences currently used (1 to
4)
3: Message mode (Always set to C)
4: Route No. (001 to 300, 3 digits required)
5 through 12: Waypoint name (Max. 8
names, length of each waypoint name is
fixed to 7 byte)
1:
2:
3:
4:
5:
Note 1: Following characters can be used
for comments:
_ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789&'#
=9
=>
=B
=F
=;
=:
=?
=<
=@
=D
=C
=G
Note 2: A route can may contain 35
waypoints and GPRTE sentence for
one route data may exceed 80 byte
limitation. In this case, route data is
divided into several GPRTE
sentences (Max. 4 sentences). This
value shows the number of
sentences the route data has been
divided.
Route comment data format
$PFEC, GPrtc,
1
==
=A
=E
=H
Character available for comment
xx, c----c <CR><LF>
2
Route comment format
1: Route No. (01 to 200, 3 digits required)
2: Route comment (Max. 16 characters,
variable length)
The same characters of the comment for
waypoint comment can be used.
End of sentence
$PFEC, GPxfr,
CTL, E <CR><LF>
End of sentence
10-11
10. CUSTOMIZING YOUR UNIT
This page is intentionally left blank.
10-12
11. USING C-MAP NT MODEL
The GP-1650WD/1650W C-MAP NT series
uses FURUNO mini chart cards and C-MAP
NT-FP chart cards. These charts show
accurate coastlines, depth contours, place
names, aids to navigation such as buoys and
lighthouses, and other navigational marks.
11.1 Inserting Chart Card
1. Push down the lid catch to open the chart
card slot cover.
Card slot
Location of chart card slot cover
2. Insert appropriate chart card groove side
up.
3. Close the slot cover to protect the chart
drive. (Keep the slot cover closed at all
times.)
Note 1: Turn off the power before inserting
or ejecting the chart card.
Note 2: When using C-MAP NT-FP card, do
not eject it while a chart is being
drawn. This may cause the
equipment to stop working.
11-1
11. USING C-MAP NT MODEL
11.2 Cursor and Data Display
Besides its fundamental functions of
providing position data, the cursor can also
show caution area, depth area, source of
data, etc. Further, you can display
information about an icon by placing the
cursor on it.
1. Press the cursor pad to turn the cursor
on.
34° 12.345' N
135° 12.345' E
FROM 16.45nm
OS
276.9°
NORTH
UP
5. Press the ENTER soft key or the
[ENTER] key to display details for object
selected Objects.
Caution area
Information
LEUCHTFEUER DIE KARTE ENTHAEL
T NUR DIE LAGEN DER WICHTIGEN
FEUER. LIGHTS ONLY THE PRINC
IPAL LIGHTS ARE SHOWN ON THIS
CHART. MISSWEISUNG SIEHE K
ARTEN GROESSEREN MASSSTABS. M
AGNETIC VARIATION LOCAL MAGNE
TIC ANOMALIES SEE LARGER SCAL
E CHARTS.
ZOOM
IN
ZOOM
OUT
COURSE
UP
GO TO
CURSOR
CENTER
DGPS 3D
Plotter display
2. Use the cursor pad to place the cursor on
the position desired.
3. Press the [ENTER] key to open the
Objects window. For example the
following window appears.
PORT
SERVICE
Objects
Example of caution area window
6. Press the CANCEL soft key to close the
window.
7. Repeat steps 4 to 6 to select other item.
8. Press the CANCEL soft key to close the
Objects window.
When you place the cursor on any icon, its
information appears.
1. Place the cursor on a lighthouse icon.
Place the cursor
on a lighthouse icon.
NAVAID : X X X X X X 6S 7m 9M
FROM OS 2. 43nm
351. 2°
ZOOM
Caution area
Depth area
PUNTA CORNACCHIA
Source of data
ACCO AMENO
NORTH
UP
IN
ZOOM
OUT
ENTER
COURSE
UP
ISCHIA PORTO
GO TO
CURSOR
CANCEL
DGPS 3D
CENTER
DGPS 3D
Objects window
Lighthouse icon
4. Press ▲ or ▼ to select the item desired.
2. Press the [ENTER] key. For example, the
following window appears.
11-2
11. USING C-MAP NT MODEL
11.3 Tidal Information
Objects
Navigation mark, fixed
Extended navigational aid, ge
Light
Light
Light
Light
R
Depth contour
G
Land area
W
R
Source of data
The C-MAP NT-FP chart card provides for
calculation of the tide heights for any date.
Additionally it displays the times of sunrise
and sunset.
1. Press the cursor pad to place the cursor
on a Tide icon.
T
Object windows
3. Press ▲ or ▼ to select the item desired.
4. Press the [ENTER] key to display
detailed information.
Navigation mark, fixed
Light.
Color
white
Height
7. 00 Meters
Light characteristic
occulting
XXXXXXXX
XXXXXXXX
Tide icon
2. Press the [ENTER] key to open the
Objects window.
Objects
Tide height
Depth contour
Caution area
Depth area
Source of data
Sample lighthouse data
5. Press the CANCEL soft key to close the
Objects window.
Objects window
3. Press ▲ or ▼ to select Tide height.
4. Press the ENTER soft key or the
[ENTER] key to open the TIDE window.
Time:
12:00
Height: 1.01 ft
Draught: 0.82 ft
01/01/00 +01
59 26. 467' N
010 28. 646' E
Port Info
HORTEN
High Water (max)
Low Water (min)
Sunrise
09:15L
1.32
1.07
0.82
0.57
0.32
0
4
8
12
16
20
24
1.32 ft (13:15)
0.32 ft (21:45)
Sunset
15:27L
TIDE window
11-3
11. USING C-MAP NT MODEL
5. Press the DATE soft key to open the
DATE window.
DATE
DD/MM/YYYY
01 / 01 / 2000
DATE window
6. Use ◄ or ► to position the cursor where
desired and then press the appropriate
numeric keys to enter a date.
7. Press the ENTER soft key or the
[ENTER] key to show the tidal graph for
entered date.
8. Press ◄ or ► to locate the vertical
cursor on the time desired. Time and
height are shown to the left of the graph.
9. Press ▲ or ▼ to shift the level cursor.
Draught is shown to the left of the graph.
10. Press the CANCEL soft key to close the
TIDE window.
11.4 Navigating to Ports, Port
Services
The C-MAP NT-FP chart provides detailed
information on aids to navigation (buoy,
lighthouse) and port service information. The
port service information includes the
availability of water and fuel supplies,
shipyards, first aid, etc. You can use the list
to set destination as follows:
1. Press the [MENU] key to open the main
menu.
2. Press the DISPLAY OPTIONS soft key.
3. Press ▼ to select SET GO TO METHOD
and press the EDIT soft key. The SET
GO TO METHOD window appears.
SET GO TO METHOD
1 POINT
35 POINT
WPT/PORT SER
SET GO TO METHOD window
4. Press ▼ to select WPT/PORT SER and
press the ENTER soft key or the
[ENTER] key.
5. Press the [PLOT] key once or twice to
return the plotter display.
6. Press the GO TO soft key. Soft key titles
change. If the GO TO soft key is not
displayed, press the cursor pad.
+ 40˚45.971'N
13˚57.462'E
FROM
OS
0.26 nm
180.2˚
GO TO
QUICK
ROUTE
NEAR
SRVICE
PUNTA CORNACCHIA
ACCO AMENO
ISCHIA PORTO
CASAMICCIOLA
I. ISCHIA
DGPS 3D
Plotter display
11-4
CANCEL
GO TO
11. USING C-MAP NT MODEL
7. Press the NEAR SRVICE soft key.
The SELECT PORT SERVICE window
appears.
+
40˚45.971'N
13˚57.462'E
FROM
QP<01>
0.26 nm
180.2˚
GO TO
ZOOM
IN
ZOOM
OUT
Currently selected icon
PUNTA CORNACCHIA
SELECT PORT SERVICE
ACCO AMENO
ADD
QP
Health emergency
ISCHIA PORTO
CASAMICCIOLA
DGPS 3D
I. ISCHIA
USE
SOFT KEYS TO MAKE
ROUTE THEN PRESS "ENTER"
ERASE
LST QP
CANCEL
GO TO
Make route window
SELECT PORT SERVICE window
8. Use the cursor pad to select service mark
desired. Currently selected icon is
circumscribed. The name of currently
selected icon appears at the top of the
window. Refer to the user's manual of
C-MAP NT for details about the icons.
9. Press the ENTER soft key or the
[ENTER] key. Then, the display shows
the locations of those services nearest
you.
+
40˚45.971'N
13˚57.462'E
FROM
OS
0.26 nm
180.2˚
GO TO
11. Do one of the following:
Go directly to port service selected:
Press the [ENTER] key. The own ship
and the port service is connected by a
blue line. The range and bearing from
own ship to the port service appears at
the navigation data display.
You can go to the port service directly by
steering the ship to the heading
indicated.
Go to port service selected via
waypoints, make a route as follows:
a) Move the cursor to the nearest waypoint
of the port service.
b) Press the ADD QP soft key.
c) Repeat the above steps a) and b) to enter
other waypoints.
d) Press the [ENTER] key to finish.
PUNTA CORNACCHIA
ACCO AMENO
ENTER
ISCHIA PORTO
CASAMICCIOLA
DGPS 3D
I.SELECT
ISCHIA ICON BY
KEY.
CANCEL
GO TO
Sample filling station locations
A line connects between own ship,
waypoints and the port service. Further,
the range and bearing from own ship to
first waypoint appears.
Note: Destination is automatically cancelled
if there is no port for service selected.
10. Press ▲ or ▼ to place the "hand cursor"
on the port service icon desired and
press the ENTER soft key or the
[ENTER] key.
11-5
11. USING C-MAP NT MODEL
11.5 Setting Chart Setup
Options
CHART DETAILS menu
1. Press the [MENU] key followed by the
CHART SETUP OPTIONS and CHART
DETAILS soft key.
LAT/LON GRID
TEXT INFO
WAYPOINT
WAYPOINT NAME
INDEX
LANDMASS
BACKGROUND
NAV AIDS
SECTOR INFO
OTHER SYMBOLS
MARK SIZE
GREEN
ON
LARGE
ON
ON
BRT YELLOW
BLUE
ON
ON
WHITE
STD
CHART
DETAIL
34° 12.345' N
135° 12.345' E
FROM 16.45nm
OS
276.9°
EDIT
NORTH
UP
ZOOM
IN
DEPTH
INFO
ZOOM
OUT
COURSE
UP
GO TO
CURSOR
RETURN
DGPS 3D
SECTOR INFO: Turns lighthouse viewable
angle indication on C-MAP NT-FP chart
on/off. Viewing angle is shown as an arc
extending from lighthouse position. This
feature is available with selected charts.
When OFF is selected, the visual information
is not displayed and the lighthouse is
displayed as "!".
Sector info
Chart details menu
2. Press ▲ or ▼ to select item and press
the EDIT soft key.
3. Select option with cursor pad and press
the ENTER soft key or the [ENTER] key.
4. Press the RETURN soft key to finish.
CENTER
DGPS 3D
Lighthouse
34° 12.345' N
135° 12.345' E
FROM 16.45nm
OS
276.9°
ZOOM
IN
ZOOM
OUT
COURSE
UP
Items which are concerned with C-MAP
NT-FP chart cards are described here.
GO TO
CURSOR
DGPS 3D
LANDMASS: Selects brightness and color of
land. When you select OFF, color of land is
black.
BACKGROUND: Not available with C-MAP
NT-FP chart card.
NAV AIDS: Turns aids to navigation symbols
(for example, buoys) on/off. When OFF is
selected, symbols are displayed but
information is not displayed (at the upper
part of the screen).
11-6
NORTH
UP
CENTER
Lighthouse appearance
when sector info is off
OTHER SYMBOLS: Selects color of all
other chart symbols. When OFF is selected,
navaid icons are not displayed but alarm
icons are displayed.
DEPTH INFO soft key: Turns the DEPTH
INFO display on/off and sets it color on
FURUNO charts, or selects the depth areas
limit and spot sounding & bathymetric range
in C-MAP NT-FP chart.
11. USING C-MAP NT MODEL
1. With the CHART DETAILS menu
displayed, press the DEPTH INFO soft
key to show the following display.
FOR FURUNO CHART
DEPTH
DEPTH
DEPTH
DEPTH
< 10 m
= 10 m
> 10 m
INFO
RED
YELLOW
LIGHT BLUE
RED
DEPTH
INFO
EDIT
10 m : APPROX. 30 ft or 5 fa
11.6 Selecting Chart
Scale/Range
FOR C-MAP CHART
SHADE CHANGE DPTH 0020, 0164 ft
SPOT SOUNDING &
0033~3000 ft
BATHYMETRIC RANGE
DGPS 3D
SPOT SOUNDING &
BATHYMETRIC RANGE: Sets the depth
range to display the spot sounding on the
C-MAP NT-FP chart. The depth range is
displayed red.
RETURN
Depth info display
2. Press ▲ or ▼ to select item and press
the EDIT soft key or enter the appropriate
value by using numeric keys.
3. Select option with cursor pad and press
the ENTER soft key or the [ENTER] key.
4. Press the RETURN soft key several
times to finish.
Chart scale (range) may be selected with the
ZOOM IN or ZOOM OUT soft key. ZOOM IN
expands the chart; ZOOM OUT shrinks it.
The range selected is momentarily displayed
at the lower left-hand corner.
Note: When the display is expanded or
shrunk beyond the range of the chart
card in use the chart is not displayed,
and an appropriate chart icon
appears.
SHADE CHANGE DPTH: Sets two
values in the range of Depth Limit on the
DEPTH INFO display when the C-MAP
NT-FP chart is used. The Depth Areas
are shown on the screen in three colors
depending on depth.
0 to left value: Blue
left value to right value: Light-blue
greater than right value: Light-gray
(Maximum value: 12000 meter or
39369 ft)
In the figure above, as the following,
0 - 20 ft: Blue
20 - 164 ft: Light-blue
greater than 164 ft: Light-gray
Note 1: Depth data depends on the
registered value at "depth area".
Note 2: It may be difficult to distinguish
colors of track and mark/line in
sea areas painted in light-blue or
green.
11-7
11. USING C-MAP NT MODEL
11.7 Displaying Program
Number
1. Press the [MENU] key to open the main
menu.
2. Press the CONFIGURATION soft key to
show the CONFIGURATION n menu.
3. Press the SYSTEM MENU soft key to
open the SYSTEM MENU.
4. Press the SELF TEST soft key to open
the TEST menu.
5. Press the MEMORY, I/O TEST soft key to
start the test. Test results and program
numbers. are shown as below.
Program Number
TEST
PROGRAM: OK
No.14518150**
SRAM: OK
INTERNAL
BATTERY: OK
GPS
RECEIVER: OK
No.48502060**
DRAM: OK
PORT1: -- -PORT2: -- --
BEACON
RECEIVER: OK
No.08501781**
No.
RETURN
Memory, I/O test results
11-8
12. MAINTENANCE &
TROUBLESHOOTING
12.1 Maintenance
Regular maintenance is essential for good
performance. A maintenance program should
be established and should at least include
the items listed in below.
WARNING
Do not open the equipment.
Hazardous voltage which can
cause electrical shock, burn or
serious injury exists inside the
equipment. Only qualified
personnel should work inside
the equipment.
Recommended maintenance program
Item
Antenna
Check point
Check for loosened and corroded bolts.
Remedy
Tighten loosened bolts. Replace
heavily corroded bolts.
Check connection point for
watertightness.
Antenna cable
Check connector for tightness and
corrosion.
Replace damaged pats.
Check cables for damage.
Display unit connectors
Check for tight connection.
Tighten loosened connectors.
Ground terminal
Check for tight connection and corrosion.
Clean or replace as necessary.
Dust and foreign material on the display
unit.
Dust may be removed with a soft cloth,
if necessary anti-static cleaner may be
used. Never use chemical solvents to
clean the display; they can remove
paint and markings.
Dust and foreign material on the screen.
Wipe the LCD carefully to prevent
scratching, using tissue paper and an
LCD cleaner. To remove dirt or salt
deposits, use an LCD cleaner, wiping
slowly with tissue paper so as to
dissolve the dirt or salt. Change paper
frequently so the salt or dirt will not
scratch the LCD. Do not use solvents
such as thinner, acetone or benzene
for cleaning.
Display unit
LCD
12-1
12. MAINTENANCE & TROUBLESHOOTING
12.2 Replacement of Fuse,
Battery
The fuse on the power cable protects the
system from reverse polarity of the ship’s
mains and equipment fault. If the fuse blows,
find the cause before replacing it. Use only a
3 A fuse. Using the wrong fuse will damage
the unit and void the warranty.
CAUTION
Use the correct fuse.
Use of a wrong fuse can cause fire or
damage the equipment.
A battery installed on the circuit board inside
display unit preserves data when the power
is turned off. The life of the battery is about
three years. When the battery voltage is low
the battery icon ( ) appears on the display.
When this happens, contact your dealer to
request replacement of the battery.
Type
Code Number
Lithium
Battery
CR2450-F2 ST2L
000-144-941
Note : Use only the specified battery. Use of
an incorrect battery may cause
explosion. Dispose of the battery in
accordance with local regulations.
12.3 Simple Troubleshooting
Below are simple troubleshooting
procedures which the user can follow to
restore normal operation.
Simple troubleshooting (plotter)
If …
Then …
check for blown fuse.
check that the power connector is firmly tightened.
you cannot turn on the power
check for corrosion on power cable connector.
check for damaged power cable.
check ship’s battery for proper voltage output (12/24 V).
power is on but nothing appears
press the [POWER/BRILL] key and then the cursor pad
to adjust display brilliance and tone.
there is no response when a key is pressed
turn on the power again.
check for loosened antenna connector.
position is not fixed within 90 seconds.
check GPS receiver status indication.
track is not plotted
plotting is stopped. (“H” appears on the plotter display.)
bearing is wrong
check that correct magnetic variation is entered on the
DISPLAY OPTIONS menu.
loran or Decca TDs do not appear
check that proper Loran or Decca chain codes are
entered on the DISPLAY UNIT.
loran TDs are wrong
enter TD offset on the GPS/DGPS/TD OPTIONS menu.
ship’s speed display is not zero after ship is stopped
try to decrease GPS speed smoothing setting on the
GPS/DGPS/TD OPTIONS menu.
12-2
12. MAINTENANCE & TROUBLESHOOTING
12.4 Error Messages
SYSTEM
MENU
The GP-1650W/1650WD displays the
following error messages on the alarm menu
to alert you to possible trouble.
SELF TEST
DEMONSTRATION MODE
MEMORY/TRIP CLEAR
Error messages
Error Message
NO GPXS FIX
Meaning, remedy
No GPS signal. Check
antenna cable.
NO DIFFERENTIAL
No DGPS signal. Check
GPS
antenna.
CORRECTION.
(GP-1650WD only)
DGPS 3D
RETURN
System menu
4. Press the SELF TEST soft key to open
the TEST menu.
TEST
VOLTAGE
OF Voltage
of
internal
INTERNAL
battery is low. Request
BATTERY IS LOW. replacement of battery.
MEMORY•I/O TEST
KEYBOARD TEST
TEST PATTERN
12.5 Diagnostic Tests
Memory, I/O port test
DGPS 3D
This test conducts a general check of the
display unit and the antenna unit. The unit
displays the results for each device or
component checked as OK or NG (No
Good).
1. Press the [MENU] key to open the main
menu.
2. Press the CONFIGURATION soft key to
show the CONFIGURATION menu.
Test menu
5. Press the MEMORY•I/O TEST soft key to
start the test. Test results and program
nos. are shown as below.
TEST
PROGRAM: OK
No.14518010**
SRAM: OK
PORT1: OK
PORT2: OK
SETUP NMEA/DGPS PORT 2
UPLOAD/DOWNLOAD DATA
SYSTEM MENU
INTERNAL
BATTERY: OK
GPS
RECEIVER: OK
No.48502060**
DRAM: OK
CONFIG
SETUP NMEA PORT 1
RETURN
BEACON
RECEIVER: OK
No.08501781**
No.
RETURN
: Special connections are required to check these ports.
Otherwise, "--" appears.
**: Program Version No.
Memory, I/O test results
DGPS 3D
RETURN
Configuration menu
3. Press the SYSTEM MENU soft key to
open the SYSTEM menu.
6. The test runs continuously. To return to
the TEST menu, press the RETURN soft
key.
Note: BEACON RECEIVER results only
appear on GP-1650WD.
12-3
12. MAINTENANCE & TROUBLESHOOTING
Keyboard test
TEST PATTERN
This test checks all controls for proper
operation.
WHT
1. Press the [MENU] followed by the
CONFIGURATION, SYSTEM MENU and
SELF TEST soft keys to display the
TEST menu.
2. Press the KEYBOARD TEST soft key to
display the screen for testing the
keyboard.
RED
GRN
BLU
PRESS "ENTER" TO CHANGE PATTERN
WHT
KEYBOAD
TEST
▲
▲
▲
PRESS
"CLEAR" KEY
3 TIMES
TO RETURN.
▲
RED
Keyboard test
3. Press each key one by one. The pressed
key’s on-screen location turns black if the
key is functioning properly.
4. To escape, press the [CLEAR] key three
times.
GRN
BLU
Display test
1. Press the [MENU] key followed by the
CONFIGURATION, SYSTEM MENU and
SELF TEST soft keys to display the
TESTmenu.
2. Press the TEST PATTERN soft key to
open the test pattern display.
3. Press the [ENTER] key to change the
test pattern.
12-4
BLK
Display test pattern
BLK
RETURN
12. MAINTENANCE & TROUBLESHOOTING
12.6 Clearing Memories
The memory, which stores marks, tracks and
initial settings, can be cleared to start afresh.
When this done all default settings are
restored.
1. Press the [MENU] key followed by the
CONFIGURATION and SYSTEM MENU
soft key.
2. Press the MEMORY/TRIP CLEAR soft
key to open the clear memory menu.
CLEAR
MEMORY
CLEAR PLOTTER MEMORY NO
CLEAR GPS MEMORY
NO
CLEAR ALL MEMORY
NO
TRIP METER RESET
NO
DGPS 3D
EDIT
RETURN
Clear memory menu
3. Press ▲ or ▼ to select memory or trip
meter reset.
4. Press the EDIT soft key.
5. Press ▲ to select YES.
6. Press the ENTER soft key or the
[ENTER] key to clear item selected.
Note: For CLEAR PLOTTER MEMORY and
CLEAR ALL MEMORY, all waypoints
and routes are cleared and default
settings are restored. If you require
this data, save it to a PC beforehand.
12-5
12. MAINTENANCE & TROUBLESHOOTING
This page is intentionally left blank.
12-6
MENU TREE
MENU key
Default settings shown in bold italic.
CHART SETUP OPTIONS
CHART OFFSET
TRACK CONTROL
Default settings shown in bold italic.
CHART DETAILS
DEPTH INFO Soft key
FURUNO chart
DEPTH < 10m (ON, OFF; RED)
DEPTH = 10m (ON, OFF; YELLOW)
DEPTH > 10m (ON, OFF; LIGHT BLUE)
DEPTH INFO (ON, OFF; RED)
(COLORS: RED, YELLOW, GREEN,
LIGHT BLUE, PURPLE, BLUE, WHITE)
SPOT SOUNDING & BATHYMETARIC RANGE
(0 - 9999 ft,0 - 33 ft)
C-MAP NT chart
SHADE CHANGE DPTH
SPOT SOUNDING & BATHYMETRIC RANGE
DISPLAY OPTIONS
GPS/DGPS/TD OPTIONS
DISPLAY TRACK (ON, OFF)
TRACK COLOR
(RED, YELLOW, GREEN, LIGHTBLUE, PURPLE, BLUE, WHITE)
PLOT (TIME, DISTANCE)
TIME INTERVAL (00m10s)
DIST INTERVAL (00.10nm)
TRACK MAMORY (2000 POINTS)
LAT/LON GRID (ON, OFF; GREEN)
TEXT INFO (ON, OFF)
WAYPOINT (LARGE, SMALL, OFF)
WAYPOINT NAME (ON, OFF)
INDEX (ON, OFF)
LANDMASS (BRT, DIM, OFF; YELLOW)
BACKGROUND (BLACK, BLUE)
NAV AIDS (ON, OFF)
SECTOR INFO (ON, OFF)
OTHER SYMBOLS (ON, OFF; WHITE)
(RED, YELLOW, GREEN, LIGHT BLUE,
PURPLE, BLUE, WHITE)
MARK SIZE (STD, SMALL)
RNG & BRG MODE (GREAT CIRCLE, RHUMB LINE)
RANGE/SPEED UNIT (nm/kt, km/km/h, sm/sm/h)
DEPTH UNIT (m, ft, fa)
TEMP UNIT (°C, °F)
LAT/LON DISPLAY
(DD°MM.MM', DD°MM.MMM', DD°MM.MMMM')
TIME DISPLAY (12HOUR, 24HOUR)
WAYPOINTS SW (AUTO1, AUTO2, MANUAL)
COURSE VECTOR (VECTOR, LINE, OFF)
BEARING (TRUE, MAGNETIC)
MAG VARIATION (AUTO, MANUAL)
TD DISPLAY (LORAN-C, DECCA)
POSITION DISPLAY (LAT/LON, TD)
SET GO TO METHOD
(1POINT, 35POINT, WPT/PORT SERVICE)
OPERATION MODE (PLEASURE, FISHING1, FISHING 2)
LANGUAGE (ENGLISH, FRENCH)
GPS SETUP OPTIONS
DGPS/WAAS SETUP OPTIONS
1
TD SETUP
Loran C Default: 9940, 11-27 (US West Coast)
Decca Default: Chain: 01, R-G (South Baltic)
LOCAL TIME OFFSET (00:00)
GEODETIC DATUMS (WGS-84)
POS SMOOTHING (000 sec)
SPD/CSE SMOOTHING (005 sec)
GPS SPEED AVE (060 sec)
LAT OFFSET (0.000'N)
LON OFFSET (0.000'E)
DISABLE SATELLITE
LATITUDE (38.00.000'N)
LONGITUDE (123.00.000'W)
ANT. HEIGHT (005m)
FIX MODE (2D, 2D/3D)
DGPS/WAAS MODE (DGPS, WAAS, AUTO, OFF)
BEACON FREQUENCY (AUTO, MANUAL)
BEACON BAUD RATE (AUTO, 50, 100, 200)
WAAS SEARCH (AUTO, MANUAL)
CORRECTIONS DATA SET (00 to 99, 02)
DGPS/WAAS ALARM (ON, OFF)
LORAN C
(GRI, CORRECTION1, 2)
DECCA
(DEC CHAIN, CORRECTION1, 2)
A-1
MENU TREE
1
CONFIGURATION
SETUP NMEA PORT 1
FORMAT
(NMEA0183Ver.1.5, 2.0)
LAT/LON FORMAT
(DD°MM.MM', DD°MM.MMM', DD°MM.MMMM)
SETUP NMEA/DGPS PORT 2
FORMAT
(NMEA0183Ver.1.5, 2.0, RTCM104EX, RTCM104INTRN,
RTCM104OUT)
LAT/LON FORMAT
(DD°MM.MM', DD°MM.MMM', DD°MM.MMMM)
SELECT SNTNC. soft key
(AAM, APB, BOD, BWC/BWR*, GGA,
GLL, MTW, RMA, RMB, RMC, VTG, WPL, XTE,
ZDA)
*: BWR: For RHUMB LINE
BWC: For GREAT CIRCLE
UPLOAD/DOWNLOAD DATA
SYSTEM MENU
DOWNLOAD WAYPOINT/RTE TO PC
UPLOAD WAYPOINT/RTE FROM PC
SAVE DATA TO MEMORY CARD
LOAD DATA FROM MEMORY CARD
SELF TEST (MEMORY, I/O; KEYBOARD;
TEST PATTERN, REMOTE CONTROLLER
TEST)
DEMO MODE
DEMONSTRATION MODE
DEMO SPEED
DEMO START LAT
DEMO START LON
MEMORY/TRIP CLEAR
CLEAR PLOTTER MEMORY (NO, YES)
CLEAR GPS MEMORY (NO, YES)
CLEAR ALL MEMORY (NO, YES)
TRIP METER RESET (NO, YES)
WPT/RTE key
WAYPOINTS
LOCAL LIST
ALPHA/NUMERIC LIST
WAYPOINT BY CURSOR
WAYPOINT BY RANGE & BEARING
ROUTES
LOG
CREATE VOYAGE BASED ROUTE
ALARM key
Page 1
A-2
AUDIO ALARM (ON, OFF)
ARRIVAL ALARM (ON, OFF)
ANCHOR ALARM (ON, OFF)
PROXIMITY ALARM (ON, OFF)
XTE ALARM (ON, OFF)
SPEED ALARM (WITHIN, OVER/UNDER, OFF)
LORAN C CHAINS
Chain
GRI
S1
S2
S3
S4
S5
Central Pacific
4990
11
29
–
–
–
Canadian East Coast
5930
11
25
38
–
–
Commando Lion (Korea)
5970
11
31
42
–
–
Canadian West Coast
5990
11
27
41
–
–
South Saudi Arabia
7170
11
26
39
52
–
Labrador Sea
7930
11
26
–
–
–
Eastern Russia
7950
11
30
46
61
–
Gulf of Alaska
7960
11
26
44
–
–
Norwegian Sea
7970
11
26
46
60
–
Southeast USA
7980
11
23
43
59
–
Mediterranean Sea
7990
11
29
47
–
–
Western Russia
8000
10
25
50
65
–
North Central USA
8290
11
27
42
–
–
North Saudi Arabia
8990
11
25
40
56
69
Great Lakes
8970
11
28
44
59
–
South Central USA
9610
11
25
40
52
65
West Coast USA
9940
11
27
40
–
–
Northeast USA
9960
11
25
39
54
–
Northwest Pacific (old)
9970
11
30
55
81
–
Icelandic
9980
11
30
–
–
–
North Pacific
9990
11
29
43
–
–
Suez
4991
10
24
England, France
8940
12
30
Northwest Pacific
8930
11
30
50
70
Newfoundland East Coast
7270
11
25
Lessay
6731
10
39
BØ
7001
11
27
Sylt
7499
11
26
Ejde
9007
10
23
38
Saudia Arabia North
8830
11
25
39
56
Saudia Arabia South
7030
11
25
37
55
A-3
DECCA CHAINS
Chain
No.
Chain
Chain
code
Location
Chain
no.
Chain
Chain
code
Location
01
South Baltic
0A
Europe
34
Kanto
8C
Japan
02
Vestlandet
0E
"
35
Shikoku
4C
"
03
Southwest British
1B
"
36
Hokuriku
2C
"
04
Northumbrian
2A
"
37
Kita Kyushu
7C
"
05
Holland
2E
"
38
Namaqualand
4A
06
North British
3B
"
39
Cape
6A
"
07
Lofoten
3E
"
40
Eastern Province
8A
"
3F
"
41
South West Africa
9C
"
"
08
Southern Africa
09
North Baltic
4B
"
42
Natal
10C
10
North West
4C
"
43
Dampier
8E
11
Trondelag
4E
"
44
Port Headland
4A
12
English
5B
"
45
Anticosti
9C
13
North Bothnian
5F
"
46
East Newfoundland
2C
"
14
Southern Spanish
6A
"
47
Cabot Strait
6B
"
15
North Scottish
6C
"
48
Nova Scotia
7C
"
16
Gulf of Finland
6E
"
17
Danish
7B
"
18
Irish
7D
"
19
Finnmark
7E
"
20
French
8B
"
21
South Bothnian
8C
"
22
Hebridean
8E
"
23
Frisian Islands
9B
"
24
Helgeland
9E
"
25
Skagerrak
10B
"
26
North Persian Gulf
5C
27
South Persian Gulf
1C
"
28
Bombay
7B
"
29
Calcutta
8B
"
30
Bangladesh
6C
"
31
Saliyah
2F
"
32
Hokkaido
9C
Japan
33
Tohoku
6C
"
A-4
Persian Gulf & India
Australia
"
Northern America
WORLD TIME
A-5
GEODETIC CHART LIST
001:
002:
003:
004:
005:
006:
007:
008:
009:
010:
011
012:
013:
014:
015:
016:
017:
018:
019:
020:
021:
022:
023:
024:
025:
026:
027:
028:
029:
030:
031:
032:
033:
034:
035:
036:
037:
038:
039:
040:
041:
042:
043:
044:
045:
046:
047:
048:
049:
050:
Islands
051:
052
053:
054:
055:
056:
057:
058:
059:
060:
061:
062:
063:
064:
065:
066:
067:
068:
069:
070:
071:
072:
073:
074:
075:
076:
077:
078:
079:
080:
081:
082:
083:
084:
085:
086:
087:
088:
089:
090:
091:
092:
WGS84
WGS72
TOKYO
NORTH AMERICAN 1927
EUROPEAN 1950
AUSTRALIAN GEODETIC 1984
ADINDAN-MN
ADINDAN-E
ADINDAN-MA
ADINDAN-SE
ADINDAN-SU
AFG
AIN EL ABD 1970
ANNA 1 ASTRO 1965
ARC 1950-MN
ARC 1950-B
ARC 1950-L
ARC 1950-M
ARC 1950-S
ARC 1950-ZR
ARC 1950-ZM
ARC 1950-ZB
ARC 1960-MN
ARC 1960-K
ARC 1960-T
ASCENSION IS. 1958
ASTRO BEACON “E”
ASTRO B4 SOR. ATOLL
ASTRO POS 71/4
ASTRONOMIC STATION 1952
AUSTRALIAN GEODETIC 1966
BELLEVUE (IGN)
BERMUDA 1957
BOGOTA OBSERVATORY
GAUPO INCHAUSPE
CANTON IS. 1966
CAPE
CAPE CANAVERAL
CARTHAGE
CHATHAM 1971
CHUA ASTRO
CORREGO ALEGRE
DJAKARTA (BATAVIA)
DOS 1968
EASTER IS. 1967
EUROPEAN 1950-WE
EUROPEAN 1950-CY
EUROPEAN 1950-EG
EUROPEAN 1950-ESC
EUROPEAN 1950-EIS
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Mean Value (Japan, Korea & Okinawa)
Mean Value (CONUS)
Mean Value
Australia & Tasmania
Mean Value (Ethiopia & Sudan)
Ethiopia
Mali
Senegal
Sudan
Somalia
Bahrain Is.
Cocos Is.
Mean Value
Botswana
Lesotho
Malawi
Swaziland
Zaire
Zambia
Zimbabwe
Mean Value (Kenya & Tanzania)
Kenya
Tanzania
Ascension Is.
Iwo Jima Is.
Tern Is.
St. Helena Is.
Marcus Is.
Australia & Tasmania
Efate & Erromango Islands
Bermuda Islands
Columbia
Argentina
Phoenix Islands
South Africa
Mean Value (Florida & Bahama Islands)
Tunisia
Chatham Is. (New Zealand)
Paraguay
Brazil
Sumatra Is. (Indonesia)
Gizo Is. (New Georgia Is.)
Easter Is.
Western Europe
Cyprus
Egypt
England, Scotland, Channel & Shetland Islands
England, Ireland, Scotland, & Shetland
EUROPEAN 1950-GR
EUROPEAN 1950-IR
EUROPEAN 1950-SA
EUROPEAN 1950-SI
EUROPEAN 1950-NF
EUROPEAN 1950-PS
EUROPEAN 1979
GANDAJIKA BASE
GEODETIC DATUM 1949
GUAM 1963
GUX 1 ASTRO
HJORSEY 1955
HONG KONG 1363
INDIAN-TV
INDIAN-BIN
IRELAND 1965
ISTS 073 ASTRO 1969
JOHNSTON IS. 1961
KANDAWALA
KERGUELEN IS.
KERTAU 1948
LA REUNION
L. C. 5 ASTRO
LIBERIA 1964
LUZON
LUZON-M
MAHE 1971
MARCO ASTRO
MASSAWA
MERCHICH
MIDWAY ASTRO 1961
MINNA
NAHRWAN-O
NAHRWAN-UAE
NAHRWAN-SA
NAMIBIA
MAPARIMA, BWI
NORTH AMERICAN 1927WU
NORTH AMERICAN 1927EU
NORTH AMERICAN 1927AK
NORTH AMERICAN 1927BH
NORTH AMERICAN 1927SS
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Greece
Iran
Italy, Sardinia
Italy, Sicily
Norway & Finland
Portugal & Spain
Mean Value
Republic of Maldives
New Zealand
Guam Is.
Guadalcanal Is.
Iceland
Hong Kong
Thailand & Vietnam
Bangladesh, India & Nepal
Ireland
Diego Garcia
Johnston Is.
Sri Lanka
Kerguelen Is.
West Malaysia & Singapore
Mascarene Is.
Cayman Brac Is.
Liberia
Philippines (excl. Mindanao Is.)
Mindanao Is.
Mahe Is.
Salvage Islands
Eritrea (Ethiopia)
Morocco
Midway Is.
Nigeria
Masirah Is. (0man)
United Arab Emirates
Saudi Arabia
Namibia
Trinidad & Tobago
Western United States
Eastern United States
Alaska
Bahamas (excl. San Salvador Is.)
Bahamas, San Salvador Is.
A-6
093:
094:
095:
096:
097:
098:
099:
100:
101:
102:
103:
104:
105:
106:
107:
108:
109:
110:
111:
112:
113:
114:
115:
116:
117:
118:
119:
120:
121:
122:
123:
124:
125:
126:
127:
128:
129:
130:
131:
132:
133:
134:
135:
136:
137:
138:
139:
140:
141:
142:
143:
144:
145:
146:
147:
148:
149:
150:
151:
152:
153:
154:
155:
156:
157:
158:
159:
160:
161:
162:
163:
164:
165:
166:
167:
168:
169:
170:
171:
172:
173:
NORTH AMERICAN 1927CN
: Canada (incl. Newfoundland Is.)
NORTH AMERICAN 1927AB
: Alberta & British Columbia
NORTH AMERICAN 1927EC
: East Canada
NORTH AMERICAN 1927MO
: Manitoba & Ontario
NORTH AMERICAN 1927NE
: Northwest Territories & Saskatchewan
NORTH AMERICAN 1927YK
: Yukon
NORTH AMERICAN 1927CZ
: Canal Zone
NORTH AMERICAN 1927CR
: Caribbean
NORTH AMERICAN 1927CA
: Central America
NORTH AMERICAN 1927CU
: Cuba
NORTH AMERICAN 1927GR
: Greenland
NORTH AMERICAN 1927MX
: Mexico
NORTH AMERICAN 1983AK
: Alaska
NORTH AMERICAN 1983CN
: Canada
NORTH AMERICAN 1983CS
: CONUS
NORTH AMERICAN 1983MX
: Mexico, Central America
OBSERVATORIO 1966
: Corvo & Flores Islands (Azores)
OLD EGYPTIAN 1930
: Egypt
OLD HAWAIIAN-MN
: Mean Value
OLD HAWAIIAN-HW
: Hawaii
OLD HAWAIIAN-KA
: Kauai
OLD HAWAIIAN-MA
: Maui
OLD HAWAIIAN-OA
: Oahu
OMAN
: Oman
ORDNANCE SURVEY OF GREAT BRITAIN 1936-MN: Mean Value
ORDNANCE SURVEY OF GREAT BRITAIN 1936-E: England
ORDNANCE SURVEY OF GREAT BRITAIN 1936-IM: England, Isle
of Man & Wales
ORDNANCE SURVEY OF GREAT BRITAIN 1936-SSI: Scotland, &
Shetland Islands
ORDNANCE SURVEY OF GREAT BRITAIN 1936-WL: Wales
PICO DE LAS NIVIES
: Canary Islands
PITCAIRN ASTRO 1967
: Pitcairn Is.
PROVISIONS SOUTH CHILEAN 1963: South Chile (near 53°S)
PROVISIONAL SOUTH AMERICAN 1956MN: Mean Value
PROVISIONAL SOUTH AMERICAN 1956BO: Bolivia
PROVISIONAL SOUTH AMERICAN 1956NC: Chile-Northern Chile
(near 19°S)
PROVISIONAL SOUTH AMERICAN 1956SC: Chile-Southern Chile
(near 43°S)
PROVISIONAL SOUTH AMERICAN 1956CO: Columbia
PROVISIONAL SOUTH AMERICAN 1956EC: Ecuador
PROVISIONAL SOUTH AMERICAN 1956GY: Guyana
PROVISIONAL SOUTH AMERICAN 1956PR: Peru
PROVISIONAL SOUTH AMERICAN 1956VN: Venezuela
PUERTO RICO
: Puerto Rico & Virgin Islands
QATAR NATIONAL
: Qatar
QORNOQ
: South Greenland
ROME 1940
: Sardinia Islands
SANTA BRAZ
: Sao Maguel, Santa Maria Islands (Azores)
SANTO (DOS)
: Espirito Santo Is.
SAPPER HILL 1943
: East Falkland Is.
SOUTH AMERICAN 1969MN
: Mean Value
SOUTH AMERICAN 1969AG
: Argentina
SOUTH AMERICAN 1969BO
: Bolivia
SOUTH AMERICAN 1969BR
: Brazil
SOUTH AMERICAN 1969CH
: Chile
SOUTH AMERICAN 1969CO
: Columbia
SOUTH AMERICAN 1969EC
: Ecuador
SOUTH AMERICAN 1969GY
: Guyana
SOUTH AMERICAN 1969PA
: Paraguay
SOUTH AMERICAN 1969PR
: Peru
SOUTH AMERICAN 1969TT
: Trinidad & Tobago
SOUTH AMERICAN 1969VZ
: Venezuela
SOUTH ASIA
: Singapore
SOUTHEAST BASE
: Porto Santo & Madeira Islands
SOUTHWEST BASE
: Faial, Graciosa, Pico, Sao Jorge, & Terceira Is.
TIMBALAI 1948
: Brunei & East Malaysia (Sarawak & Sadah)
TOKYO JP
: Japan
TOKYO KP
: Korea
TOKYO OK
: Okinawa
TRISTAN ASTRO 1968
: Tristan da Cunha
VITI LEVU 1916
: Viti Levu Is. (Fiji Islands)
WAKE-ENIWETOK 1960
: Marshall Islands
ZANDERIJ
: Surinam
BUKIT RIMPAH
: Bangka & Belitung Islands (Indonesia)
CAMP AREA ASTRO
: Camp Mcmurdo Area, Antarctica
G. SEGARA
: Kalimantan Is. (Indonesia)
HERAT NORTH
: Afghanistan
HU-TZU-SHAN
: Taiwan
TANANARIVE OBSERVATORY 1925 : Madagascar
YACARE
: Uruguay
RT-90
: Sweden
Pulkovo 1942
: Russia
Finish KKJ
: Finland
SPECIFICATIONS OF
COLOR GPS/ PLOTTER: GP-1650W
COLOR DGPS/ PLOTTER: GP-1650WD
1
GENERAL
1.1
Display
5.6-inch high resolution color LCD
1.2
Projection
Mercator
1.3
Usable Area
85° latitude or below
1.4
Display Mode
Plotter, Video pilot, Highway display, Waypoint display
1.5
Alarms
Arrival and Anchor watch, Cross track error and proximity alarms,
Ship’s speed in and out alarms
2
GPS RECEIVER
2.1
Receiving Channels
GPS
12 channels parallel, 12 satellite tracking
WAAS
1 channel
2.2
Rx Frequency
1575.42 MHz
2.3
Rx Code
C/A code, WAAS
2.4
Position Fixing System
All in view, 8-state Kalman filter
2.5
Position Accuracy
GPS
10 m (95% of the time, HDOP ≤ 4)
DGPS
5 m (95% of the time), external data required for GP-1650W
WAAS
3 m (95% of the time)
2.6
Tracking Velocity
999 kts
2.7
Position-fixing Time
Warm start: 12 s approx., Cold start: 90 s approx.
2.8
Position Update Interval
1s
3
DISPLAY SECTION
3.1
Effective Area
115.2 × 84.2 mm
3.2
Display Pixels
234 × 320 dots
3.3
Position Indication
Latitude/longitude or Loran C LOP or DECCA LOP
4
PLOTTER
4.1
Effective Projection Area
0.125 nm to 2,048 nm (at equatorial area)
4.2
Track Display
Plot interval: by time (1 to 59 min. 59 sec.) or
by distance (0.01 to 99.99 nm)
4.3
Colors
Red, yellow, green, purple, light-blue, blue, white
4.4
Memory Capacity
Track/Mark: 5000 points, waypoint: 800 point
4.5
Storage Capacity
Simple route: 200 routes with 35 waypoints each
4.6
MOB
1 point
4.7
Quick Route
1 course
SP - 1
E4424S01A-M
4.8
Electronic Chart
FURUNO or NAVIONICS chart card available,
C-MAP chart card also available for C-MAP NT Model
5
INTERFACE
5.1
Input Data
IEC61162-1, NMEA 0183 Ver1.5
$**DBT, $**DPT, $**MTW, $**TLL, $GPWPL
5.2
Output Data
IEC61162-1, NMEA 0183 Ver1.5
$GPAAM, $GPAPB, $GPBOD, $GPBWR/GPBWC, $GPGLL,
$GPGGA, $GPRMA, $GPRMB, $GPRMC, $GPVTG, $GPXTE,
$GPZDA, $GPWPL
6
POWER SOURCE
6.1
Display Unit
12-24 VDC: 1.1-0.5 A
6.2
Rectifier (PR-62, option)
100/110/115/220/230 VAC, 1 phase, 50/60 Hz
7
ENVIRONMENTAL CONDITIONS
7.1
Ambient Temperature
Antenna Unit
-20ºC to + 70ºC
Display Unit
-15ºC to +55ºC
7.2
Relative Humidity
95% at +40ºC
7.3
Waterproofing (IEC 60529)
Antenna Unit
IPX6
Display Unit
IPX5
7.4
Vibration
IEC 60529
8
COATING COLOR
8.1
Display Unit
Cover: Munsell 2.5GY5/1.5, Panel: N3.0
8.2
Antenna Unit
N9.5 (white)
SP - 2
E4424S01A-M
INDEX
A
Alarm information window 8-4
ALARM key 8-1
Alarm messages 8-4
Alarms
alarm information window 8-4
alarm message 8-4
anchor watch alarm 8-2
arrival alarm 8-1-8-2
audio alarm 8-1
DGPS alarm 10-7-10-8
proximity alarm 8-3
speed alarm 8-3
XTE alarm 8-2-8-3
Anchor watch alarm 8-2
Arrival alarm 8-1-8-2
Audio alarm 8-1
Antenna height 10-7
Auto course-up mode 2-1
B
Background color
chart 10-2
Battery replacement 12-2
Beacon baud rate 10-7
Beacon frequency 10-7
Beacon information display 2-7
Brilliance adjustment 1-3
Buoy data 2-4-2-5
C
Chart details menu 10-2
Chart offset menu 10-1
Chart scale 2-3
Chart setup options menu 10-1–10-2
Configuration menu 10-11–10-14
Course vector 10-3
Course-up mode 2-1
Cross-track error alarm. See XTE alarm
Cursor 2-2
Cursor data 11-2
D
Decca chains A-5
DECCA station selection 11-8
Demonstration display 1-6
DGPS/WAAS alarm 10-7
DGPS beacon information display 2-7
DGPS/WAAS mode 10-6
DGPS/WAAS setup options menu
10-6-10-7
Diagnostics
display test 12-3
keyboard test 12-4
memory, I/O test 12-3
Disable satellite 10-6
Display options menu 10-3-10-4
Display test 12-3
Downloading data 10-10
E
Error messages
12-3
F
Fix mode 10-6
Fuse replacement 12-2
G
Geodetic chart list A-6
Geodetic datum 10-5
GPS satellite monitor display 2-6
GPS/DGPS/TD options menu 10-4-10-8
Great circle 10-3
Grid 10-2
H
Highway display 2-8
I
Indications
enlargement of nav data 2-6
K
Keyboard test 12-4
L
Lat/lon display resolution 10-3
Lighthouse data 2-5
Local time 10-5
Loran C chains A-3
Loran C station selection 10-7
Index-1
INDEX
M
Magnetic bearing 10-3
Magnetic variation 10-4
Maintenance 12-1
Mark
color 4-3
number used 4-4
entering 4-1
erasing 4-4
line 4-3
displaying 4-4
shape 4-2
Memory card
formatting 9-1
loading data 9-3
saving data 9-2
Memory clear 12-5
Memory, I/O port test 12-3
MENU key 1-5
Menu tree A-1–A-2
Mini chart cards
aids to navigation data 2-4
background color 10-2
buoy data 2-4
chart scale 2-3
chart symbol color 10-2
chart symbols 2-4
depth info 10-2
grid 10-2
Indices 2-3, 10-2
inserting 1-2
landmass color 10-2
lighthouse data 2-5
nav aids 10-2
port service icons (NAVIONICS) 2-5
text info 10-2
MOB 5-1
N
Nav data display 2-6
Navigation
cancelling 7-6
multiple quick points 7-1
ports, port service 7-2
quick points 7-1
restarting 7-4
route 78-4
route in reverse order 7-4
single quick point 7-1
specific route leg 7-4
switching route waypoints 7-5
waypoints 7-2
North-up mode 2-1
O
Object 11-2
Operation mode 2-9
P
Pleasure mode 2-9
PLOT key 1-4
Port services
description 2-5
navigating to 7-2
Position format selection 10-4
Position input 10-6
Power on/off 1-2
POWER/BRILL key 1-3
Presentation modes 2-1
Program number 11-8, 12-3
Proximity alarm 8-3
activating, deactivating 8-3
setting radius for individual waypoints 5-3
Q
Quick points
entry method 7-1
multiple points 7-1
single point 7-1
R
Range selection 2-3
Range unit 10-3
Rhumb line 10-3
Routes
connecting (two) 6-2
entering by cursor 6-2
entering through route list 6-1
entering track based 6-4
erasing 6-6
inserting waypoints on the plotter display 6-3
inserting waypoints through route list 6-3
navigating 7-4
navigating in reverse order 7-4
removing from plotter display 6-4
removing waypoints through route list 6-3
restarting navigation of 7-4
switching waypoints 7-5
Index-2
INDEX
S
SAVE/MOB key 5-1
Sector info (lighthouse viewable angle) 10-2
Setup NMEA port 1 menu 10-9
Setup NMEA port 2 menu 10-9
Smoothing
position 10-5
speed/course 10-5
Soft keys 1-5
Speed
GPS speed averaging 10-6
input (for ETA calculation) 7-5
unit 10-3
Speed alarm 8-3
Steering display 2-7
System configuration v
System menu 10-12
SYSTEM SETUP soft key 11-8
T
TD setup menu 10-7
Temperature unit 10-3
Tidal Information 11-3
Time
display selection 10-3
local 10-5
Trip
2-10
Tone adjustment 1-3
Track
color 3-2
displaying 3-1
erasing 34-4
plotting interval 3-2
stopping/restarting plotting of
Track based route 6-4
Trip distance reset 12-5
Troubleshooting 12-2
entering at MOB position 5-1
entering at own ship's position 5-1
entering by cursor 5-1
entering by latitude and longitude position 5-4
entering by range and bearing 5-3
erasing 5-4
mark size 5-6
name entry 5-3
name on/off 10-2
navigating by 7-2
proximity alarm radius 5-3
searching 5-6
shape 5-2
size 10-2
World time A-5
WPT/RTE key 5-1
X
XTE alarm 8-3
XTE scale 2-8
3-1
U
Upload/download data menu 10-9
Uploading data 10-10
W
Waypoints
changing data 5-5
changing position at entry 5-2
changing position on plotter screen 5-5
color 5-2
comments 5-3
Index-3