Furuno GP-90 GPS Receiver User Manual

Back
INSTALLATION MANUAL
GPS NAVIGATOR
GP-90
1. EQUIPMENT LIST ............................................................................................ 1
2. DISPLAY UNIT .................................................................................................. 2
3. ANTENNA UNIT ................................................................................................ 3
4. WIRING ............................................................................................................. 5
5. INITIAL SETTINGS ........................................................................................... 7
6. OPTIONAL DGPS ........................................................................................... 18
7. TAPING ANTENNA UNIT GPA-018S ............................................................. 19
PACKING LISTS & INSTALLATION MATERIALS........................................... A-1
OUTLINE DRAWINGS ...................................................................................... D-1
INTERCONNECTION DIAGRAM ......................................................................S-1
SAFETY INSTRUCTIONS
WARNING
Do not work inside the
equipment unless totally
familiar with electrical
circuits.
Hazardous voltage which can
cause electrical shock, burn
or serious injury exists inside
the equipment.
Turn off the power at the
mains switchboard before
beginning the installation.
Post a sign near the switch
to indicate it should not be
turned on while the equipment is being installed.
Fire, electrical shock or
serious injury can result if the
power is left on or is applied
while the equipment is being
installed.
CAUTION
Ground the display unit to
prevent loss of sensitivity
and mutual interference.
Confirm that the power supply voltage
is compatible with the voltage rating
of the equipment.
Connection to the wrong power supply
can cause fire or equipment damage. The
voltage rating appears on the label at the
rear of the display unit.
Use the correct fuse.
Use of a wrong fuse can cause fire or
equipment damage.
Keep the following compass safe
distances:
Standard Steering
Display unit
0.45 m
0.30 m
1.
EQUIPMENT LIST
Standards
Name
Antenna Unit
Display Unit
Installation
Materials
Spare Parts
Type
GPA-017S
GPA-018S
GPA-019S
GP-90-N
GP-90-A
CP20-01900
CP20-01950
SP20-00500
Q'ty
Mass
(kg)
1
1
1 set
Remarks
For DGPS
2.2
Without Beacon RX
With Beacon RX
See lists at end of
With Antenna Cable
manual.
Without Antenna Cable
1 set
Options
Name
Flush Mount Kit S
Flush Mount Kit F
Antenna Cable Set
Antenna Cable Assy.
Right Angle Antenna
Base
L-Type Antenna Base
Handrail Antenna Base
Mast Mount Kit
Cable Assy
Beacon Receiver Set
Rectifier
DGPS Beacon
Receiver
Whip Antenna
Type
OP20-24
OP20-25
CP20-01700
CP20-02700
CP20-01710
CP20-02710
TNC-PS-3D-15
Code No.
004-393-000
004-393-280
004-372-110
004-381-160
004-372-120
004-381-170
000-133-670
No.13-QA330
000-803-239
No.13-QA310
No.13-RC5160
CP20-01111
MJ-A6SPF0011-050
(03S9202)
MJ-A6SPF0011-100
(03S9226)
MJ-A7SPF0003-050
(20S0241)
MJ-A6SPF0003-050C
(20S0093)
MJ-A6SPF0012-050C
(64S4073)
MJ-A6SPF0012-100C
(64S4071)
OP20-32-1
OP20-32
OP20-33
OP20-34
000-803-240
000-806-114
004-365-780
For antenna unit.
000-132-244
Cross Cable 5m, 6p-4p
000-132-336
Cross Cable 10m, 6p-4p
PR-62
GR-80
FAW-1.2
Remarks
For display unit.
CP20-01701+30 m cable
CP20-02701+30 m cable
CP20-01701+50 m cable
CP20-02701+50 m cable
15 m
000-136-730-01 5m, For DATA4
000-154-054-10 5m
000-154-053-10 Cross cable 5m
000-154-037-10 Cross cable 10m
000-041-018
000-041-019
000-041-596
000-041-598
000-013-485
000-013-486
With GPA-018S
With whip antenna and OP20-32-1
With GPS-019S
Without whip antenna
For 100VAC mains
For 220VAC mains
000-130-046
1.2 m
1
2.
DISPLAY UNIT
The display unit can be installed with either of four methods as shown below. Refer to the
outline drawing at the end of manual.
•
•
•
•
Locate the unit away from exhaust pipes and vents.
The mounting location should be well ventilated.
Mount the unit where shock and vibration are minimal.
Keep the display unit away electromagnetic field generating equipment such as motor,
generator.
• Allow sufficient maintenance space and a sufficient slack in cables for maintenance and
repair.
Table Top and Overhead Mounting
TABLE TOP
OVERHEAD
Display unit mounting methods
Flush mounting type F
An optional flush mount kit type F is required. For details, see outline drawing at end of
manual.
Name
Flush Mount Kit F
Type
OP20-25
Code No.
004-393-280
Flush mounting type S
An optional flush mount kit type S is required. For details, see outline drawing at end of
manual.
Name
Flush Mount Kit S
2
Type
OP20-24
Code No.
004-393-000
3.
ANTENNA UNIT
Mounting
Install the antenna unit referring to the installation diagram at end of manual. When
selecting a mounting location for the antenna unit, keep in mind the following points.
• Select a location out of the radar beam. The radar beam will obstruct or prevent reception
of the GPS satellite signal.
• Be sure the location offers a clean line-of-sight to satellite. Objects within line-of-sight to
a satellite, for example, a mast or funnel, block reception and cause prolonged acquiring time
or interruption of position fix.
• Mount the unit as high as possible. Mounting the antenna as high as possible keeps it free
of water spray, which can intercept reception of GPS satellite signal, if water spray is frozen.
• The antenna unit GPA-018S must be grounded. Connect ground wire of 1.25 sq or larger
(local supply) between the antenna unit and a stainless steel screw fastened to the mast.
• The antenna unit GPA-018S must be taped. See chapter 7 for instructions.
Extending Antenna Cable Length
The standard cable is 15m long. 30m and 50m long extension cable sets are optionally
available.
!Extension cable line-up
Fabricate the end of antenna cable and attach the coaxial connector. Details are shown
on next page.
Antenna Unit
GPA-019S
Cable length Necessary parts
GPA-018S GPA-017S
CP20-01700
CP20-02700
CP20-01710
CP20-02710
30 m
50 m
20cm
Code no.
004-372-110
004-381-160
004-372-120
004-381-170
: Connector
Conversion Cable Assy.
Antenna Cable
1m
30 m or 50 m
For CP20-01700, CP20-01710
1m
To display unit
Fabricate locally. (See the next page.)
OR
TNCP-NJ
Conversion Cable Assy.
Antenna Cable
30 m or 50 m
For CP20-02700, CP20-02710
1m
To display unit
Fabricate locally. (See the next page.)
Extension Cable Line-up
!Waterproofing the connector
Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with
cable-tie.
How to waterproof the connector of the antenna cable
3
3. ANTENNA UNIT
How to attach the N-P-8DFB connector
Outer Sheath
Armor
Inner Sheath Shield
50
Remove outer sheath and armor by the dimensions
shown left.
Expose inner sheath and shield by the dimensions
shown left.
30
Cover with heat-shrink tubing and heat.
Cut off insulator and core by 10mm.
10
30
Twist shield end.
Clip on clamp nut, gasket and clamp as shown left.
Clamp
Nut
Gasket Clamp
(reddish
brown)
Aluminum Foil
Fold back shield over clamp and trim.
Trim shield here.
Insulator
Cut aluminum foil at four places, 90° from one
another.
Fold back aluminum foil onto shield and trim.
Trim aluminum
tape foil here.
1
Expose the insulator by 1mm.
5
Expose the core by 5mm.
Pin
Clamp Nut
Shell
Solder through
the hole.
4
Slip the pin onto the conductor. Solder them together
through the hole on the pin.
Insert the pin into the shell. Screw the clamp nut into
the shell.
(Tighten by turning the clamp nut. Do not tighten by
turning the shell.)
4.
WIRING
The figure below shows the connection of cables on rear of display unit.
CAUTION
Ground the display unit to
prevent loss of sensitivity
and mutual interference.
Antenna Unit
GPA-019S
GPA-018S GPA-017S
20cm
Rear of Display Unit
DATA1
ANT
Ground
DATA2
DATA3
DATA4
External Equipment
INPUT
12~24 VDC
–
Black
+
Red
FUSE 2A
Connection of cables on display unit
5
4. WIRING
Grounding
The display unit contains several CPUs. While they are operating, they radiate noise, which
can interfere with other radio equipment. Ground the unit as follows to prevent it.
• The grounding wire should be 1.25sq or larger.
• The grounding wire should be as short as possible.
External Equipment
The DATA1, DATA2, and DATA3 ports are used to connect an external equipment such as
autopilot, remote display, navigation equipment. Refer to the interconnection diagram on
page S-1 for connection of DATA1, DATA2 and DATA 3 port. The DATA4 port is used to
connect NMEA equipment, IBM-PC or DGPS beacon receiver as follows;
Connection of DATA4 port
In case of RS-422 Level
DATA4
TD-A
TD-B
RD-A
RD-B
S·G
1
2
3
4
5
6
7
RS-422 level
IBM PC
Beacon Receiver
NMEA equipment
In case of RS-232C Level
DATA4
RD
NC
SD
S·G
1
2
3
4
5
6
7
RS-232C level
IBM PC
Beacon Receiver
NMEA equipment
NOTE: See page 15 for selection of input/output signal.
6
5.
INITIAL SETTINGS
Checking Operation
1. Turn on the GP-90.
2. Confirm that "OK" and "BEACON RCVR INSTALLED" are displayed on the self-test
display.
PROGRAM MEMORY
SRAM
Internal Battery
=OK
=OK
=OK
BEACON RCVR INSTALLED
DATA 3: DATA OUTPUT
Confirm that "BEACON RCVR
INSTALLED" is displayed when
DGPS function is provided.
Self-test display at equipment start up
3. Press [MENU ESC], [8] and [1]. Confirm that "BEACON OK" is displayed.
DGPS Setup
The default setting is "manual".
Automatic DGPS setup
The beacon receiver (GR-7000A) can automatically select optimum reference station by
feeding GP-90’s position data. If it takes more than 5 minutes to fix DGPS position at the
automatic mode, switch to manual mode. Use the manual mode when an external beacon
receiver has no automatic function of station selection.
1. Press [MENU ESC], [9] and [7] to display the DGPS SETUP menu.
WAAS/DGPS SETUP
MODE
GPS
WAAS SEARCH
Auto Man (GEO= ___ )
CORRECTIONS DATA SET 00
Auto Man (ID= ___ )
DGPS Station
288.0kHz
Freq.
200 bps
Baud Rate
These items appear when
"Man" is selected.
:Select
ENT: Enter
MENU: Escape
Figure 5-1 DGPS SETUP menu
2. Press S or T to select DGPS MODE and press W to select “INT BEACON”.
3. Press S or T to select DGPS Station.
4. Press W to select Auto.
7
5. INITIAL SETTINGS
5. Press the [NU/CU ENT] key.
6. Press the [MENU ESC] key.
Manual DGPS setup
Enter four digit ID number, frequency and baud rate of station.
1.
2.
3.
4.
5.
Press [MENU ESC], [9] and [7] to display the DGPS SETUP menu.
Press S or T to select DGPS MODE and press W to select “INT BEACON”.
Press S or T to select DGPS Station.
Press W to select Man.
Enter four digit ID number. You can clear an entry by the [CLEAR] key.
If there is no ID number, press the [NU/CU ENT] key.
6. Press the [NU/CU/ENT] key.
If the number entered is invalid, the buzzer sounds and the message "INVALID ID" appears
on the display for three seconds.
7. Enter frequency in four digits (283.5 kHz to 325.0 kHz).
8. Press the [NU/CU ENT] key. "Baud Rate" appears in reverse video.
9. Press W or X to select baud rate; 25, 50, 100 or 200bps.
10. Press the [MENU ESC] key.
DGPS Operation checking
1. Press [MENU ESC] and [7].
2. Press [ ] several times to display the following.
D3D
SAFE
Jan 21 2005 23:59’59" U
100m
DGPS INTEGRITY STATUS
NAME: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Health: 0
ID: 274
Freq: 323.0 kHz
Bit Rate: 200 bps
SNR: 21 dB
Sig Strength: 83 dB
DGPS DATA:
BEACON STATION:
This value is between 1 to 22. The higher
the value, the better the reception of
beacon signal. When this value is less
than 20, the error is included in the
correction data. In this time, position
fixing is done by using past position data.
When the ship is in the service area of a
beacon station, this value should be 21 or
22. If not, check as follows.
Good
Good
:STATION MESSAGE
MENU:Escape
Beacon signal status
Reference station status
DGPS signal strength
This value is between 1and 84.
The higher the value,
the stronger the signal.
If a noise appears at reception band width,
the value becomes bigger.
Figure 5-2
8
Signal to noise ratio
• Check the grounding.
• Check the radar beam interference.
• Check the noise of power generator of
the ship.
5. INITIAL SETTINGS
Input/Output Setting
The GP-90 can output navigation information to external equipment. For example, it can
output position data to a radar or echo sounder for display on their display screen. You can
convert a Loran Plotter to a GPS Plotter with position data from the GP-90.
Before selecting data to output, confirm what data the external equipment requires. Output
necessary data only. Outputting unnecessary data can cause receiving problems at the
external equipment.
Talker
All data transmitted by marine electronics equipment is prefixed with a two-character code
which tells external equipment what equipment is transmitting data. This two-character code
is called the talker. The GP-90 contains the talkers GP, LC and DE.
Because GPS is a relatively new system some early model equipments do not recognize
the GP talker name. In this case transmit data using a conventional talker, which equipment
recognizes, such as Loran C.
9
5. INITIAL SETTINGS
Data format and data output availability
Output data sentence of IEC 61162-1 and NMEA 0183 Ver. 1.5/2.0.
AAM:
APB:
Waypoint arrival alarm
Autopilot sentence B
magnitude of cross track error, direction to steer, arrival alarm, bearing to waypoint
("Heading to steer to destination waypoint data" not used)
BOD: Bearing-origin to destination
BWC: Bearing and distance to waypoint-great circle
BWR: Bearing and distance to waypoint-rhumb line
BWW: Bearing-waypoint to waypoint
DTM: Datum reference
GGA: Global positioning system (GPS) fix data
time of fix, latitude, longitude, quality indicator, number of satellites in use, DOP,
altitude, geoidal separation
("age of dgps data" and "differential reference station ID" not used)
GLL:
Geographic position-latitude/longitude
GNS: GNSS fix data
GBS: GPS satellite fault detection
RMB: Recommended minimum navigation information cross track error, direction to steer,
origin and destination waypoint ID, destination waypoint latitude and longitude,
range and bearing of destination waypoint, destination closing velocity, arrival
alarm
RMC: Recommended minimum specific GPS/TRANSIT data
UTC of position fix, latitude and longitude, ground speed and course, date,
magnetic variation
RTE: Routes
VDR: Set and drift
VTG: Course over ground and ground speed
WCV: Waypoint closure velocity
WPL: Waypoint location
XTE: Cross-track error, measured
ZDA: Time and date
Rnn:
Routes
Also, following NMEA 0183 Ver. 1.5 sentence is output.
APA:
10
Autopilot sentence "A"
magnitude of cross track error, direction to steer, arrival alarm, bearing origin to
destination.
5. INITIAL SETTINGS
Input data sentence of NMEA 0183 Ver. 1.5/2.0
Checksum is checked if attached, and if any errors are found, the sentence becomes invalid.
Talker ID is not distinguished.
DBT: Depth below transducer
DPT: Depth
HDG: Heading, deviation and variation
HDM: Heading, magnetic
HDT: Heading, true
MTW: Water temperature
TLL: Target latitude and longitude
VBW: Dual ground/water speed
VHW: Water speed and heading.
FURUNO proprietary sentence
AGFPA: Autopilot information from FURUNO autopilot equipments.
11
5. INITIAL SETTINGS
AGFPA: Autopilot information from FURUNO autopilot equipments
Port
DATA1
DATA2
DATA3
DATA4
Input
NMEA 0183
Ver. 1.5 /2.0
AGFPA , DBT, DPT,
HDG, HDM, HDT,
MTW, TLL, VBW,
VHW
External MOB
DGPS or general data
(Selected by menu)
Output
IEC 61162-1/NMEA 0183 Ver.1.5/
Ver.2.0
AAM, APA, APB, BOD, BWC, BWR,
BWW, GGA, GLL, GNS, RMB, RMC,
VDR, VTG, WCV, WPL, XTE, ZDA,
GBS, Rnn, RTE
LOG PULSE
Same as the data output form “DATA1”
General data
IEC 61162-1/NMEA 0183 Ver.1.5/
Ver.2.0
AAM, APA, APB, BOD, BWC, BWR,
BWW, GGA, GLL, GNS, RMB, RMC,
VDR, VTG, WCV, WPL, XTE, ZDA,
GBS, Rnn, RTE
General data
1) Input of waypoint data
Connect YEOMAN equipment to DATA4 port.
2) Input and output of waypoint / route data
Rate of operation
The TX rate of operation is the percentage of data output in one second, and it appears on
the screen. If short intervals are assigned to many sentences, the rate of operation
increases as illustrated below
TX
TX
TX
Note: Output data should be less than 100%.
When the external equipment cannot display correct data input from the GP-90, the rate of
operation should be lowered. For example, set a rate of operation less than 60 % for the
Temperature Indicator TI-20.
12
5. INITIAL SETTINGS
DATA 1 output setting
1) Press [MENU], [9] and [3]. The DATA 1, 3 OUTPUT SETUP menu appears.
DATA 1, 3 OUTPUT SETUP
Data Fmt.
Talker ID
Output Data
V1.5
GP
(00-90 sec)
V2.0 IEC
LC
DE
100%
1. AAM:00 APA:00 APB:04 BOD:00
2. BWC:00 BWW:00 GGA:00 GLL:01
3. RMB:01 RMC:00 VTG:01
4. VDR:00 WPL:00 XTE:00
5. GNS:00 GBS:01 Rnn:00
200ppm
DATA3. Log Pulse
ENT : Enter
WCV:00
ZDA:01
RTE:00
400ppm
MENU : Escape
Settings shown here are default settings.
This line appears only when LOG is
selected by internal jumper wires.
Figure 5-3 DATA 1, 3 OUTPUT SETUP menu
2)
3)
4)
5)
6)
7)
Press S or T to select Data Fmt.
Press W or X to select V1.5, V2.0 or IEC.
Press the [ENT] key. Talker ID appears in reverse video.
Press W or X to select GP, LC or DE.
Press the [ENT] key.
Enter Tx interval for each output data sentence in line 1. Tx interval is available in 00,
01, 02, 03, 04, 05, 06, 10, 15, 20, 30, 60, and 90 sec.
8) Press the [ENT] key.
9) Enter Tx interval for each output data sentence in lines 2 through 5. Press the [ENT] key
after setting each line.
In great circle navigation, BWC and WNC are output but BWR and WNR are not. In rhumb
line navigation, BWR and WNR are output but BWC and WNC are not.
The total data output are shown by percentage on the third line.
13
5. INITIAL SETTINGS
DATA 2 output setting
1) Press [MENU], [9] and [4]. The DATA 2 OUTPUT SETUP menu appears.
DATA2 OUTPUT SETUP
V1.5
Data Fmt.
Talker ID
GP
Output Data (00-90 sec)
1. AAM:00 APA:00
2. BWR:00 BWW:00
3. RMB:01 RMC:00
4. VDR:00 WPL:00
5. GNS:00 GBS:01
ENT : Enter
V2.0
IEC
LC
DE
100%
APB:04 BOD:00
GGA:00 GLL:01
VTG:01 WCV:00
XTE:00 ZDA:01
Rnn:00 RTE:00
: Select
MENU : Escape
Setting shown here are default settings.
Figure 5-4 DATA 2 OUTPUT SETUP menu
2) Follow the procedure for setting DATA 1 output.
DATA 3 output setting
The DATA 3 can output NMEA 0183 (V1.5/V2.0) /IEC 61162-1 data or log pulse by
selecting inner jumper wires. For NMEA 0183 (V1.5/V2.0) /IEC 61162-1, the same signal of
DATA 1 is output from DATA 3.
Selection of NMEA0183 or log pulse
Output data
NAV board
JP4 (2 pcs.)
JP5 (3 pcs.)
NMEA 0183 (V1.5/
V2.0)/IEC 61162-1
(default setting)
ON
OFF
Log pulse
OFF
ON
Rate of log pulse output
500 mA Max.
50 VDC
Procedure for setting of log pulse rate
1)
2)
3)
4)
5)
14
Press [MENU], [9] and [3].
Press S or T to select DATA 3. Log Pulse.
Press W or X to select log pulse for external equipment; 200 ppm or 400 ppm.
Press the [ENT] key.
Press the [ESC] key.
5. INITIAL SETTINGS
Setting DATA 4 to Data Output
1) Press [MENU], [9] and [5]. The DATA 4 I/O SETUP menu appears.
DATA 4 I/O SETUP
DATA 4. Level
Data
To Next Page
ENT : Enter
1/2
RS232C
Out
RS422
Com. DGPS
: Select
MENU : Escape
Appears only when external
DGPS receiver is used.
Figure 5-5 DATA 4 I/O SETUP menu
2)
3)
4)
5)
6)
Press S or T to select DATA4. Level.
Press W or X to select level of external equipment; RS232C or RS422.
Press the [ENT] key.
Press W or X to select Out.
Press T to select to Next Page. The DATA 4 I/O SETUP <out> menu appears.
DATA 4 I/O SETUP
<Out>
2/2
To Previous Page
Data Fmt.
Talker ID
V1.5
V2.0 IEC
GP
LC
DE
Output Data
(00-90 sec)
100%
1. AAM:00 APA:00 APB:04 BOD:00
2. BWR:00 BWW:00 GGA:00 GLL:01
3. RMB:01 RMC:00 VTG:01 WCV:00
4. VDR:00 WPL:00
XTE:00 ZDA:01
5. GNS:00 GBS:01 Rnn:00 RTE:00
ENT : Enter
MENU : Escape
Figure 5-6 DATA 4 I/O SETUP <out> menu
7) Follow "DATA 1 output setting" from step 2.
15
5. INITIAL SETTINGS
Setting DATA 4 to “COM.” (general data)
Waypoints and Routes data can be received from a personal computer, through the DATA
4 port.
1) Press [MENU], [9] and [5].
2) Press ! or " to select DATA4. Level.
3) Press # or $ to select level of personal computer; RS232C or RS422.
4) Press the [ENT] key.
5) Press $ to select Com.
6) Press " to select To Next Page. The DATA 4 I/O SETUP <Com.> menu appears.
DATA 4 I/O SETUP <Com.>
2/2
To Previous Page
Baud Rate
9600 bps
WPT/RTE WPT
LLoad Data
Command
Save Data
Command
Stop
Start
WPT/RTE
Stop
Start
: Select
ENT : Enter
MENU : Escape
Figure 5-7 DATA 4 I/O SETUP <Com.> menu
7) Press ! or " to select Baud Rate.
8) Press # or $ to select baud rate; 4800bps, 9600bps or 19200bps.
9) Press the [ENT] key.
10) Press # or $ to select WPT/RTE.
11) Press " to select Command. Stop, on the same line as Command, appears in reverse
video.
12) Press $ to select Start. The message shown in Figure 5-8 appears.
Loading erases current data
and stops Route navigation
Are you sure to load?
ENT: Yes MENU: No
Figure 5-8
13) Press the [ENT] key. The message shown in Figure 5-9 appears while data is being
loaded.
Now loading
Waypoint/Route data !
MENU: Stop
Figure 5-9
16
5. INITIAL SETTINGS
14) Output data from the computer. When loading data is completed, the cursor shifts to
Stop.
15) Press the [ESC] key.
Setting DATA 4 to DGPS
An external DGPS receiver can be connected to the DATA 4 port.
Follow the procedure below to setup the GP-90 according to the specifications of the DGPS
receiver.
1) Press [MENU], [9] and [5].
2) Press ! or " to select Level.
3) Press # or $ to select level; RS232C or RS422.
4) Press the [ENT] key.
5) Press # or $ to select DGPS.
6) Press " to select To Next Page.
DATA 4 I/O SETUP <DGPS>
To previous Page
First Bit
Parity
Stop Bit
Baud Rate
2/2
MSB LSB
EVEN ODD NONE
1
2
4800
9600
: Select
ENT: Enter
MENU: Escape
Figure 5-10 DATA 4 I/O SETUP <DGPS> menu
7) Press ! or " to select First Bit.
8) Press # or $ select first bit; MSB or LSB.
9) Press " to select Parity.
10) Press # or $ to select parity bit; EVEN, ODD or NONE.
11) Press " to select Stop Bit.
12) Press # or $ to select stop bit; 1 or 2.
13) Press " to select Baud Rate.
14) Press # or $ to select baud rate; 4800 or 9600.
15) Press the [ENT] key.
16) Press the [ESC] key.
17
6.
OPTIONAL DGPS
Beacon Receiver Set GR-80
GP-90
GR-80
DATA4
RS-422* TD-A
TD-B
RD-A
RD-B
NP Board
JP3
GND
Open
Whip
Antenna
DATA
1
2
3
4
5
6
7
WHT
BLK
YEL
GRN
BLU
P
P
4
3
2
1
7
RD-A
RD-B
TD-A
TD-B
GND
RS-422
Preamp unit (with
15 m cable)
* This connection is required for L/L Auto mode of GR-80.
When the GP-90 is connected with Beacon Receiver GR-80, do the setting as follows.
Signal level
RS-422 *1
First Bit
LSB
Parity
NONE
Stop Bit
1
Baud Rate
4800 or 9600 *1
*1: Coincide with the setting of the Beacon Receiver GR-80.
Refer to page 17 for DGPS setup.
18
7.
TAPING ANTENNA UNIT GPA-018S
After inserting the whip antenna to the antenna base of GPA-018S, tape the antenna base
and whip antenna with self-vulcanizing tape and vinyl tape to reinforce the whip antenna.
1. Wrap the antenna junction point with butyl 15 tape or the equivalent.
How to wrap
1) Pull the tape to be about two times in length and wind it up, overlapping by 1/2 the width
of the tape.
2) Wrap from bottom to top, i.e., from right to left as in the picture below.
Base
Whip antenna
Antenna
Butyl tape
3) Wrap the tape from the base to a point about 60 mm, and then back to the base.
Keep tension on edge of tape, using finger to hold tape. Then, squeeze edges of tape
with thumb and index finger.
Wrap approx.
60 mm
2. Completely cover the butyl rubber tape with white vinyl tape, wrapping from the base to
the last wind of butyl tape and then back to the base.
How to wrap
1) Being careful not to pull the tape too tightly, wind tape, overlaping by approx. 1/3 of tape
width.
2) Squeeze edges of tape with thumb and index finger.
White vinyl tape
19
NAME
OUTLINE
000-802-081
5X20 SUS304
100-183-262
100-183-271
20-007-3011-2
20-007-3012-1
4
1
1
CP20-01111
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
2.(*1)の空中線部は仕様により決定されます。
ANTENNA UNIT HAS BEEN DETERMINED BY SPECIFICATION.
3
CP20-01101
FGBO-A 2A AC125V
000-549-062
(*1)
1
(*1)
1
(*1)
1
1
Q'TY
DOCUMENT
3.(*2)のアンテナケーブル組品は、有り・無しの仕様が有ります。
AVAILABLE WITH OR WITHOUT ANTENNA UNIT.
OPERATOR'S MANUAL
取扱説明書
OPERATOR'S GUIDE
操作要領書
INSTALLATION MANUAL
装備要領書
図書
OUTLINE
1/1
000-147-463 **
000-147-465 **
OMJ-4427*-*
000-147-467 **
OSJ-4427*-*
IMJ-4427*-*
000-154-054
1
1
1
1
1
(*2)
1
2
Q'TY
20AX-X-9851
000-158-000
MJ-A6SPF0003-050C
000-133-670
MJ-A2SPF0014030C
TNC-PS-3D15
20S0216
000-805-906
NO.6348 SUS303
DESCRIPTION/CODE №
20AX-X-9851 -4
OTHER INSTALLATION MATERIALS
SIGNAL CABLE ASSEMBLY
ケーブル組品MJ
POWER CABLE
ケーブル組品MJ
ANTENNA CABLE ASSY.
ケーブル組品
その他工材
HOSE CLAMP
パーカークランプ
NAME
GP-90-**-*1-**/GP-90-DUAL-**-*1-**
SP20-00500
000-040-537 **
000-041-895 **
GPA-017S
000-142-545 **
GPA-018S
000-041-054 **
GPA-019S
GP-90-E-N
DESCRIPTION/CODE №
ANTENNA UNIT INSTALLATION MATERIALS
INSTALLATION MATERIALS
SPARE PARTS
UNIT
1.コ-ド番号末尾の[**]は、選択品の代表コ-ド番号を表します。
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
PIPE
パイプ
INSTALLING SPACER
取付補助金具
空中線部工材
SELF-TAPPING SCREW
+トラスタッピンネジ 1種
工事材料
FUSE
ヒューズ
予備品
ANTENNA UNIT
空中線部
ANTENNA UNIT
空中線部
ANTENNA UNIT
空中線部
DISPLAY UNIT
受信演算部
ユニット
PACKING LIST
A-1
NAME
OUTLINE
OTHER INSTALLATION MATERIALS
INSTALLATION MATERIALS
SPARE PARTS
UNIT
000-158-000
000-133-670
MJ-A2SPF0014030C
TNC-PS-3D15
20S0216
000-802-081
5X20 SUS304
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
2.(*1)の空中線部は仕様により決定されます。
ANTENNA UNIT HAS BEEN DETERMINED BY SPECIFICATION.
3
1
(*2)
1
4
CP20-01101
FGBO-A 2A AC125V
000-549-062
(*1)
1
(*1)
1
(*1)
1
1
Q'TY
DOCUMENT
OUTLINE
3.(*2)のアンテナケーブル組品は、有り・無しの仕様が有ります。
AVAILABLE WITH OR WITHOUT ANTENNA UNIT.
INSTALLATION MANUAL
装備要領書
OPERATOR'S GUIDE
操作要領書
OPERATOR'S MANUAL
取扱説明書
図書
SIGNAL CABLE ASSEMBLY
ケーブル組品MJ
NAME
GP-90-**-*O-**/GP-90-DUAL-**-*0-**
SP20-00500
000-040-537 **
000-041-895 **
GPA-017S
000-142-545 **
GPA-018S
000-041-054 **
GPA-019S
GP-90-E-N
DESCRIPTION/CODE №
1.コ-ド番号末尾の[**]は、選択品の代表コ-ド番号を表します。
CODE NUMBER ENDED BY "**" INDICATES THE NUMBER OF TYPICAL MATERIAL.
POWER CABLE
ケーブル組品MJ
ANTENNA CABLE ASSY.
ケーブル組品
その他工材
SELF-TAPPING SCREW
+トラスタッピンネジ 1種
工事材料
FUSE
ヒューズ
予備品
ANTENNA UNIT
空中線部
ANTENNA UNIT
空中線部
ANTENNA UNIT
空中線部
DISPLAY UNIT
受信演算部
ユニット
PACKING LIST
1/1
000-147-467 **
000-147-465 **
IMJ-4427*-*
000-147-463 **
OSJ-4427*-*
OMJ-4427*-*
000-154-054
1
1
1
1
Q'TY
20AX-X-9852
MJ-A6SPF0003-050C
DESCRIPTION/CODE №
20AX-X-9852 -4
A-2
A-3
Antenna Cable Set
CP20-01700 (004-372-110)
CP20-01710 (004-372-120)
CODE NO.
004-372-420-00
TYPE
CP20-01701
20AG-X-9405 -4
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
型名/規格
DESCRIPTIONS
略 図
OUTLINE
数量
Q'TY
用途/備考
REMARKS
変換ケーブル組品
1
NJ-TP-3DXV-1
CONVERT CABLE ASSY.
CODE
NO.
2
000-123-809-00
ビニルテープ
2
NO360 0.2X19X10000
VINYL TAPE
CODE
NO.
1
000-835-215-00
コネクタ(N)
3
N-P-8DFB-CF
CONNECTOR
1
CODE
NO.
000-156-918-10
Uテープ 0.5X19X5M
絶縁テープ
4
Uテープ 0.5X19X5M
SELF-BONDING TAPE
1
000-165-833-10
000-800-985-00
CODE
NO.
20AG-X-9404 -2
CODE NO.
1/1
TYPE
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
GP-80,GP-90,SC-55,GP-3500/F,GP1850,GP-1650,FA-100,FA-150,GP1640/F,SC-60/120,GD/GP型名/規格
DESCRIPTIONS
略 図
OUTLINE
数量
Q'TY
選択 TO BE SELECTED
アンテナケーブル組品
1
ANTENNA CABLE ASSY.
8D-FB-CV *30M*
CODE
NO.
1
000-111-547-00
選択 TO BE SELECTED
アンテナケーブル組品
2
CABLE ASSY.
用途/備考
REMARKS
8D-FB-CV *50M*
CODE
NO.
1
000-117-599-00
C0014-M20-E
A-4
Antenna Cable Set
CP20-02700 (004-381-160)
CP20-02710 (004-381-170)
CODE NO.
004-381-190-00
TYPE
CP20-02701
20AX-X-9401 -5
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
型名/規格
DESCRIPTIONS
略 図
OUTLINE
数量
Q'TY
用途/備考
REMARKS
変換ケーブル組品
1
NJ-TP-3DXV-1
CONVERT CABLE ASSY.
CODE
NO.
1
000-123-809-00
ビニルテープ
2
NO360 0.2X19X10000
VINYL TAPE
CODE
NO.
1
000-835-215-00
コネクタ(N)
3
N-P-8DFB-CF
CONNECTOR
CODE
NO.
1
000-156-918-10
コネクタ
4
TNCP-NJ
CONNECTOR
1
CODE
NO.
000-156-599-10
Uテープ 0.5X19X5M
絶縁テープ
5
Uテープ 0.5X19X5M
SELF-BONDING TAPE
1
000-165-833-10
000-800-985-00
CODE
NO.
20AG-X-9404 -2
CODE NO.
1/1
TYPE
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
GP-80,GP-90,SC-55,GP-3500/F,GP1850,GP-1650,FA-100,FA-150,GP1640/F,SC-60/120,GD/GP型名/規格
DESCRIPTIONS
略 図
OUTLINE
数量
Q'TY
選択 TO BE SELECTED
アンテナケーブル組品
1
ANTENNA CABLE ASSY.
8D-FB-CV *30M*
CODE
NO.
1
000-111-547-00
選択 TO BE SELECTED
アンテナケーブル組品
2
CABLE ASSY.
用途/備考
REMARKS
8D-FB-CV *50M*
CODE
NO.
000-117-599-00
1
Apr. 18 '03
D-1
Apr. 18 '03
D-2
Apr. 18 '03
D-3
Y. Hatai
hatai
2005.12.19
11:57:12
+09'00'
D-4
D-5
Sep.29'05
D-6
Feb. 19, '03
D-7
Feb. 19, '03
D-8
C
B
A
2
*3
TNC-P-3
56
12
(-)
整流器 (+)
RECTIFIER
PR-62 *2
DPYC-1.5 *1
NMEA0183 V1.5
J12
1 ANT
2 GND
GPS ANT
INPUT
*3
MJ-A2SPF J1
アカ RED
1 (+)
クロ BLK
2 (-)
NOTE
*1. SHIPYARD SUPPLY
*2. OPTION
*3. CONNECTOR PLUG FITTED AT FACTORY.
*4. SELECTED ON MENU
*5. SELECTED BY JUMPER WIRE JP4/JP5 ON NP BOARD
(DEFAULT SETTING: IEC61162-1/NMEA0183).
3
DWG NO.
SCALE
MASS
Y. Hatai
E.MIYOSHI
TAKAHASHI.T
C4427-C01- F
Apr.17,'06
APPROVED
CHECKED
DRAWN
1
2
3
4
5
6
7
kg
GND
*1
IV-1.25sq.
DATA4
*4
[RS422/RS232C] J8
*4
TD-A
IEC61162-1/ TD-B
NMEA0183 V1.5 RD-A/RD
COM OR DGPS RD-B
SD
SG
FG
1
2
3
4
5
6
1
2
3
4
5
6
DATA2
J7
*4
TD-A
IEC61162-1/
NMEA0183 V1.5 TD-B
RD-H
RD-C
NC
GND
DATA3
J6
*5 TD-A/ALM-H
IEC61162-1/
NMEA0183 V1.5TD-B/ALM-C
MOB-H
OR MOB-C
LOG PULSE OUT
NC
MOB IN
GND
3
4
5
6
RD-H
RD-C
NC
GND
RD-A
RD-B
TD-H
TD-C
RD-A
RD-B
TD-H
TD-C
称
INTERCONNECTION DIAGRAM
GPS NAVIGATOR
相互結線図
GPS航法装置
GP-90
FURUNO ELECTRIC CO., LTD.
NAME
名
TITLE
リモートイベントスイッチ
(MOBスイッチ)
REMOTE EVENT SWITCH
(Man Over Board SWITCH)
REFER TO INSTALLATION MANUAL FOR
USING I/O DATA SENTENCES.
入出力データ、センテンスについては
装備要領書を参照のこと。
4
外部GPSビーコン受信機またはパソコンを接続するときは
装備要領書を参照のこと。
REFER TO INSTALLATION MANUAL TO CONNECT EXTERNAL
DGPS BEACON RECEIVER OR PC.
MJ-A6SPF0003-050C,5m,φ6
シロ WHT
RD-A
クロ BLK
RD-B
キ
YEL
ミドリGRN
MJ-A6SPF0003-050C,5m,φ6
シロ WHT
クロ BLK
キ
YEL
ミドリGRN
MJ-A6SPF0012-050C/100C,5/10m,φ6,6P-6P
MJ-A6SPF0011-050/100,5/10m,φ6,6P-4P
MJ-A6SPF0003-050C,5m,φ6
シロ WHT
クロ BLK
キ
YEL
ミドリGRN
*3
MJ-A7SPF0003-050,5m,φ6
MJ-A7SPF
シロ WHT
P
クロ BLK
キ
YEL
P
ミドリGRN
アカ RED
P
アオ BLU
P
P
*3
MJ-A6SPF
P
P
*3
MJ-A6SPF
P
受信演算部
*3
DATA1
J5
MJ-A6SPF
*4
DISPLAY UNIT
TD-A 1
P
IEC61162-1/
GP-90
TD-B 2
注記
*1
IV-8sq.
*1)造船所手配。
*2)オプション。
*3)コネクタは工場にて取付済。
*4)メニューにて選択。
*5)ジャンパー線JP4/JP5(NP基板)にて選択(工場設定:IEC61162-1/NMEA0183)。
100/110(115)/
220/230VAC,
50/60Hz,1φ
12-24 VDC
MJ-A2SPF0014-030C,3m,φ6
FUSE
2A
ケーブル長さは15/30/50mの選択または支給なし。
SELECT CABLE LENGTH FROM 15/30/50m SET OR NO SUPPLY.
*2
NJ-TP-3DXV
1m
TNC-PS-3D-15,15m,φ5.3
*3
TNC-P-3
*3
TNC-J-3
*2
8D-FB-CV,30/50m,φ14.3
*3
N-J-3
N-P-8DFB
*3
TNC-P-3
*3
TNC-J-3
GPA-017S
GPA-019S
0.2m
GPA-018S
0.2m
または OR
NJ-TP-3DXV,1m
GND *1
IV-2sq.
TNCP-NJ
空中線部
ANTENNA UNIT
N-P-8DFB
*3
N-J-3
1.2m WHIP
*3
TNC-P-3
1
S-1
The paper used in this manual
is elemental chlorine free.
FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone :
0798-65-2111
Fax
0798-65-4200
:
All rights reserved.
Printed in Japan
FIRST EDITION :AUG.
: AUG. 2003
C1
Pub. No. IME-44270-C1
( HIMA ) GP-90
: APR. 18, 2006
*00014746812*
*00014746812*
*00014746812*
*IME44270C10*
*IME44270C10*
*IME44270C10*