Service manual | Furuno IB-782 Marine Radio User Manual

MULTI-COMMUNICATION UNIT
IB-782
C
Yo u r L o c a l A g e n t/D e a le r
9-52, A shihara-cho,
N ishinom iya, Japan
Te l e p h o n e :
Te l e f a x :
0 7 9 8 -6 5 -2 111
0798-65-4200
A ll rig h ts re s e rv e d .
Printed in Japan
PUB. No. OM E-56095
(D A M I)
IB -782
FIRST
EDITIO N
B
:
:
AUG. 2001
O C T. 2 4 , 2 0 0 1
SAFETY INSTRUCTIONS
Safety Instructions for the Operator
WARNING
WARNING
Keep heater away from equipment.
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
A heater can melt the equipment's power
cord, which can cause fire or electrical
shock.
Only qualified personnel
should work inside the
equipment.
Keep combustible material (such as
thinner) away from the equipment.
Immediately turn off the power at the
switchboard if water leaks into the
equipment or something is dropped in
the equipment.
Fire can result.
Do not operate the equipment with wet
hands.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Electrical shock can result.
Do not disassemble or modify the
equipment.
CAUTION
Fire, electrical shock or serious injury can
result.
A warning label is attached to the
equipment. Do not remove the label.
If the label is missing or damaged,
contact a FURUNO agent or dealer.
Do not place liquid-filled containers on
the top of the equipment.
WARNING
Fire or electrical shock can result if a liquid
spills into the equipment.
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Make sure no rain or water splash leaks
into the equipment.
Fire or electrical shock can result if water
leaks in the equipment.
i
Name: Warning Label (1)
Type: 86-003-1011-0
Code No.: 100-236-230
Safety Instructions for the Installer
CAUTION
WARNING
ELECTRICAL SHOCK HAZARD
Ground the equipment to
prevent electrical shock and
mutual interference.
Do not open the equipment
unless totally familiar with
electrical circuits and
service manual.
Only qualified personnel
should work inside the
equipment.
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or equipment damage.
Be sure that the power supply is
compatible with the voltage rating of
the equipment.
Connection of an incorrect power supply
can cause fire or equipment damage. The
voltage rating of the equipment appears
on the label above the power connector.
ii
TABLE OF CONTENTS
FOREWORD......................................................................................................... iv
SYSTEM CONFIGURATION ................................................................................. v
EQUIPMENT LIST............................................................................................... vii
1. OPERATION .....................................................................................................1
1.1 Equipment Overview .......................................................................................................1
1.2 Calling .............................................................................................................................2
1.3 Receiving ........................................................................................................................2
1.4 Intercom ..........................................................................................................................3
1.5 Forwarding a Call ............................................................................................................4
1.6 Automatic Call Forwarding...............................................................................................4
1.7 Receive-Only Telephone .................................................................................................5
2. SETTINGS ........................................................................................................6
2.1 PBX Mode Settings .........................................................................................................6
2.2 OID/DID Setting...............................................................................................................7
2.3 DIP Switch Setting...........................................................................................................8
2.4 Changing Number for Connection to Inmarsat Services ..................................................8
3. MAINTENANCE................................................................................................9
3.1 Cleaning..........................................................................................................................9
4. INSTALLATION ..............................................................................................10
4.1 Mounting .......................................................................................................................10
4.2 Wiring............................................................................................................................ 11
SPECIFICATIONS
OUTLINE DRAWING
INTERCONNECTION DIAGRAM
iii
FOREWORD
A Word to the Owner of the IB-782
FURUNO Electric Company thanks you for purchasing the IB-782 Multi-Communication
Unit. We are confident you will discover why the FURUNO name has become synonymous
with quality and reliability.
For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for
quality and reliability throughout the world. This dedication to excellence is furthered by our
extensive global network of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine
environment. However, no machine can perform its intended function unless properly
installed and maintained. Please carefully read and follow the operation and maintenance
procedures set forth in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our
purposes.
Thank you for considering and purchasing FURUNO.
Features
The main features are
• Permits connection of maximum eight additional telephones and faxes for the FELCOM
82.
• Individual IDs may be assigned, for individual calling and communication log
management.
• Automatic call transfer
iv
SYSTEM CONFIGURATION
ANTENNA
UNIT
IB-180
IB-182
TEL or FAX
COMMNUNICATION
UNIT
IB-282
JUNCTION BOX
IB-313
MULTI-COMMUNICATION
UNIT
IB-782
TEL or FAX
Max. 8 units
100-200 VAC
v
: Option
EQUIPMENT LIST
Name
Multi-Communication Unit
Installation Materials
Type
Qty
Remarks
IB-782
—
1 set
vi
• Power cable (3 m)
• Tapping screw (Φ4.5, 4 pcs.)
1. OPERATION
1.1 Equipment Overview
The [POWER] switch is located on the rear panel. When the power is applied, the
diagnostic test checks the equipment for proper operation, and the “Line LEDs” on the front
panel light and go off in numerical order. After the diagnostic test is completed, only the
power lamp lights. The 1A circuit protector protects the equipment from overcurrent.
FURUNO
IB-782
M U LT I - C O M M U N I C AT I O N U N I T
P OW E R
SEND
LN0
LN1
LN2
LN3
LN4
LN5
LN6
LN7
LN8
Lights during automatic call forwarding.
Lights when the power is on.
Front panel
P OW E R
100V-220VAC 50-60Hz
1A
POWER connector
Cable Gland
POWER Switch
Circuit Protector
Ground Terminal
Rear panel
1
1.2 Calling
Below is the procedure for how call a land subscriber, make a ship-to-ship call.
1. Pick up the handset and dial “0” (number for connecting with Inmarsat services). Listen
for the dial tone.
2. Enter subscriber’s complete number (vessel ID no.), then press the [#] button.
Land subscriber
0 0
LES No.
#
Service Country Area
Code
Code Code
Subscriber's
No.
End
Code
Ship-to-ship call
0
LES No.
0
Service
Code
#
Sea Area
No.
Vessel ID No.
(Inmarsat A or B)
End
Code
Sea area no.
AOR-E: 871
POR: 872
IOR: 873
AOR-W: 874
3. Talk with subscriber.
4. Hang up the handset.
Note 1: Dial number within 20 seconds after picking up the handset, or the call will be
cancelled.
Note 2: If you misdial, hang up the handset and dial again. In addition, dial each number
within five seconds of the previous number, or the call will be cancelled.
1.3 Receiving
To answer a call:
1. When a phone rings, pick up its handset and talk with the party.
2. Hang up the handset upon completion of the call.
2
1.4 Intercom
The intercom function is available when two or more telephones are connected to the
IB-782. It allows communication between the telephones of the IB-782 and the
telephones/handset of the communication unit IB-282 and between the telephones of the
IB-782.
ANTENNA
UNIT
IB-182
Extension telephones
connected to IB-782
TEL or FAX
TEL or FAX
TEL2
TEL or FAX
MULTI-COMMUNICATION TEL3 JUNCTION
UNIT
BOX
IB-782
IB-313
TEL or FAX
TEL1
TEL1
TEL2
HANDSET
COMMUNICATION
UNIT
IB-282
TEL or FAX
TEL3
Max. 8 telephones
Connections for intercom feature
Calling IB-782’s telephones
1. Pick up the receiver and listen for the dial tone.
2. Dial party’s extension number, then press the [#] button. For example, if the party’s
extension number is “2,” dial [2], [#].
3. Talk with party.
Note: The busy tone sounds if an invalid extension number is dialed. Hang up the
receiver and dial again.
4. Hang up the receiver upon completion of the call.
Calling communication unit’s telephones
1. Pick up the receiver and dial “0” (number for connecting with Inmarsat services). Listen
for the dial tone.
2. Press the [*] button, dial party’s extension number, then press the [#] button. For
example, if the party’s extension number is “2,” dial [*], [2], [#]. Dial “0” to call the
communication unit’s handset.
3. Talk with party.
4. Hang up the receiver upon completion of the call.
Calling from communication unit’s handset to IB-782’s telephone
1.
2.
3.
4.
Pick up the handset, then press the [Intercomm] key.
Dial [3], [0], and party’s extension number (1-8).
Talk with party.
Press the [ ] key and hang up the handset upon completion of the call.
3
Calling from communication unit’s telephone to IB-782’s telephone
1.
2.
3.
4.
Pick up the receiver and listen for the dial tone.
Dial [*], [3], [0], party’s extension number (1-8), [#].
Talk with party.
Hang up the receiver upon completion of the call.
1.5 Forwarding a Call
A call may be forwarded to another telephone as follows:
How to forward a call
1. Without hanging up the receiver, press the [HOOK] key.
2. Dial telephone extension number and [#].
3. After the call has been forwarded, hang up the receiver.
Note: The busy tone sounds if an invalid extension number is dialed. Cancel forwarding as
below.
Canceling forwarding
If the called party does not answer, cancel forwarding by press the [HOOK] key. You may
also cancel forwarding by hanging up the receiver.
1.6 Automatic Call Forwarding
Calls can be automatically forwarded to another telephone as follows:
Setting
Dial [*], [9], [0], [0], extension telephone number to forward call to, [#].
Note: The SEND LED on the front panel lights when setting automatic call forwarding.
Cancelling
Dial [*], [9], [0], [0], [#]
4
1.7 Receive-Only Telephone
Any telephone connected to the IB-782 can be designated as a “receive-only telephone.”
This requires setting of a DIP switch. For this procedure see paragraph 2.3.
Setting
From the telephone to set as “receive only”, dial [*], [5], [9], [1], [#]
Cancelling
From the telephone not designated as receive-only telephone, dial [*], [5], [9], [1] and the
telephone number you wish to cancel as a receive-only telephone.
Note: The intercom function is not available from a “receive-only telephone.”
5
2. SETTINGS
2.1 PBX Mode Settings
Set the PBX mode from handset connected to the communication unit of the FELCOM 82 to
enable use of the IB-782.
1. Turn on the communication unit.
2. From the handset of the communication unit, press [FUNC Quit], [5], [9], [8] to display
the OID/OID menu.
59OID/DID
PBX Mode: ON
ON/OFF
Enter:[Ent]
Quit: {Quit]
OID/DID menu
3. Press the [ ] or [ ] key to select “PBX Mode” to ON.
59OID/D
PBX Mod
O
DID Mod
O
I
e
N
e
N
D
: ON
/OFF
: OFF
/OFF
Displayed when PBX
mode is turned ON.
Enter:[Ent]
Quit: {Quit]
OID/DID menu
4. Press the [ ] key to select DID Mode. Press the [ ] or [ ] key to select OFF.
59OID/D
PBX Mod
O
DID Mod
O
I
e
N
e
N
D
: ON
/OFF
: OFF
/OFF
Enter:[Ent]
Quit: {Quit]
OID/DID menu
5. Press the [Ent] key.
6. Press the [FUNC Quit] key to finish.
6
2.2 OID/DID Setting
Set the ID number of each telephone connected to the IB-782, from the handset connected
to the communication unit. The two-digit ID number should be the same as the telephone no.
(01-08); for example, TEL No. 2 would be “02.” ID numbers should be set after setting the
PBX mode, the instructions for which appear in the paragraph 2.1.
1. Turn on the communication unit.
2. From the handset, press [FUNC Quit], [5], [9], [3].
59OID/DID
EXT:01
NUM
OID/DOD
TEL:
/
IMN:
FAX:
/
IMN:
Enter:[Ent]
Quit: [Quit]
OID/DID menu
3. Enter telephone ID number in the EXT field, using the numeric keys.
4. Press the [ ] key, then enter OID/DID number and Inmarsat number. If the OID/DID
number is 03 and the IMN is 343164710 hit the following keys:
[0] [3] [0] [3] [ ] [3] [4] [3] [1] [6] [4] [7] [1] [0]
The cursor can be shifted with the arrow keys. The OID/DID number is a hexadecimal
number – you can switch to alphabet with the [Mode] key. To cancel input, press the
[Func Quit] key.
5. Press the [Ent] key.
6. Press the [FUNC Quit] key to quit.
7
2.3 DIP Switch Setting
SW No.
1
2
3
4
Function
How to connect to
Inmarsat services
—
Receive only
—
Default Setting
OFF
ON
OFF
OFF
ON
Connect with OFF
HOOK.
Fixed at “ON.”
YES
—
OFF
Connect by
dialing 0 or 9.
—
NO
Fixed at “OFF.”
2.4 Changing Number for Connection to Inmarsat
Services
The number for connection to Inmarsat services can be 9 or 0. Dial as below to select
number desired.
[*] [9] [1] [0] [0 or 9] [#]
8
3. MAINTENANCE
WARNING
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
3.1 Cleaning
Dust or dirt can be removed from the equipment with a soft, dry cloth. Do not use chemical
cleaners to clean the equipment – they may remove paint and markings.
9
4. INSTALLATION
4.1 Mounting
Mounting considerations
The IB-782 can be mounted on a desk or on a bulkhead. Keep the following points in mind
when selecting a mounting location:
• Leave sufficient space around the unit for maintenance and servicing.
• Locate the unit away from direct sunlight because heat can build up inside the cabinet.
• Install the unit near the telephone or facsimile which is to be connected.
• The mounting location should be stable and moderate in temperature and humidity.
• Locate the unit away from areas subject to rain and water splash.
Mounting procedure
Fix the unit to the mounting location with four tapping screws (supplied).
Tapping Screw
IB -7
f4.5 fixing
hole
MU
FU
IB-782
10
R
O
UN
PO
WE
L
R
-C
TI
OM
MU
SE
ND
NI
CA
TI
ON
UN
IT
LN
0
LN
1
LN
2
LN
3
LN
4
LN
5
LN
6
7
LN
LN
8
82
4.2 Wiring
Follow the illustration below to wire the IB-782.
MULTI-COMMUNICATION UNIT IB-782
TEL8 - TEL1
LN8-LN1
LINE
LN0
POWER
100V-220VAC 50-60Hz
1A
Ground Terminal
100-220 VAC
Power Cable (supplied)
To Communication Unit
IB-282
CAUTION
Ground the equipment to
prevent electrical shock
and mutual interference.
TEL3
5 6
Junction Box
IB-313
Local Supply (Use TTYCS-1
(Japan Industrial Standard) or equivalent.)
Armor
Shield
Conductor
Rosette
MJ-2S
S =1.25 mm 2
=1.35 mm
Vinyl sheath
Painting
TTYCS-1 sectional view
To Telephone
(or FAX)
Telephone
To Telephone
(or FAX)
Facsimile
Modular Jack Cable (supplied)
Telephone
Wiring
11
Facsimile
SPECIFICATIONS OF THE MULTI-COMMUNICATION UNIT
IB-782
1. GENERAL
(1) Outside line
1
(2) Extension line
8
(3) Dialing Method
NTT PB signal
2. POWER SUPPLY
(1) Main Unit
100-220 VAC, 1 phase, 50-60 Hz, 20 VA
(2) Power Consumption
10 W or less
3. ENVIRONMENTAL CONDITION
(1) Ambient Temperature
-15°C to +55°C
(2) Relative Humidity
93% at 40°C
(3) Water proofing
Main Unit: IPX2
(4) Vibration
IEC 60945
4. COATING COLOR
(1) Main Unit
Panel: N3.0 Newtone No. 5, Cover: 2.5GY5/1.5
SP - 1
8/8/01
Download PDF

advertising