Furuno NX-700A Stereo Receiver User Manual

NAVTEX RECEIVER
NX-700A/B
The paper used in this manual
is elemental chlorine free.
Your Local Agent/Dealer
9-52 Ashihara-cho,
Nishinomiya 662-8580, JAPAN
Telephone :
0798-65-2111
Fax
0798-65-4200
:
All rights reserved.
Printed in Japan
FIRST EDITION :MAY.
: MAY. 2005
B1
Pub. No. OME-56490
( HIMA ) NX-700
: JUL. 08, 2005
*00015280401*
*00015280401*
*00015280401*
*OME56490B10*
*OME56490B10*
*OME56490B10*
IMPORTANT NOTICE
•
No part of this manual may be copied or reproduced without written permission.
•
If this manual is lost or worn, contact your dealer about replacement.
•
The contents of this manual and equipment specifications are subject to change without
notice.
•
The example screens (or illustrations) shown in this manual may not match the screens
you see on your display. The screen you see depends on your system configuration and
equipment settings.
•
This manual is intended for use by native speakers of English.
•
FURUNO will assume no responsibility for the damage caused by improper use or
modification of the equipment or claims of loss of profit by a third party.
•
Please carefully read and follow the operation and maintenance procedures set forth in
this manual.
•
Store this manual in a convenient place for further reference.
i
SAFETY INSTRUCTIONS
Safety information for the Operator
WARNING
CAUTION
ELECTRICAL SHOCK HAZARD
A warning label is attached to the equipment. Do not remove the label. If the
label is missing or damaged, contact
a FURUNO agent or dealer about
replacement.
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
WARNING
Do not disassemble or modify the
equipment.
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
Fire, electrical shock or serious injury can
result.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
Keep heater away from equipment.
A heater can melt the equipment's power
cord, which can cause fire or electrical
shock.
Use the proper fuse.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.
ii
Name: Warning Label (1)
Type: 86-003-1011-1
Code No.: 100-236-231
Safety information for the Installer
CAUTION
WARNING
Do not open the equipment
unless totally familiar with
electrical circuits and
service manual.
Observe the following compass safe
distances to prevent deviation of a
magnetic compass.
Standard Steering
ELECTRICAL
SHOCK
HAZARD
Only qualified personnel
should work inside the
equipment.
Display unit
NX-700A
1.45 m
0.95 m
NX-700B
0.30 m
0.30 m
1.15 m
0.75 m
Receiver unit NX-7001
Turn off the power at the mains switchboard before beginning the installation.
Attach securely protective
earth to the ship's body.
Fire, electrical shock or serious injury can
result if the power is left on or is applied
while the equipment is being installed.
The protective earth is required
to the power supply to prevent
electrical shock.
iii
FORWORD
Congratulations on your choice of the FURUNO NX-700A/B NAVTEX Receiver.
We are confident that you will enjoy many years of operation with this fine piece
of equipment.
For over 50 years, Furuno Electric Company has enjoyed an enviable reputation
for quality and reliability throughout the world. Our extensive global network of
agents and dealers furthers this dedication to excellence.
The NX-700A/B is just one of the many Furuno developments in the field of
marine radio communication.
NX-700A: Display unit w/printer
NX-700B: Display unit w/o printer
This NX-700A/B provides cost-effective price, high sensitivity and simple
operation in one compact and light-weight unit. In addition to its fundamental
function of receiving NAVTEX broadcasts, this unit can also function as nav data
display when connected to navigation equipment.
This unit is designed and constructed to ensure the user many years of
trouble-free operation. To obtain full performance from the equipment, however,
you should carefully read and follow the recommended procedures for
installation, operation and maintenance. No machine can perform its intended
functions unless it is installed and maintained properly.
Thank you for considering and purchasing FURUNO equipment.
iv
Features
NAVTEX (Navigational Telex) is a world wide coastal telex broadcasting system.
Coastal NAVTEX broadcasting stations with specific ID’s transmit Navigational
warnings. Meteorological warnings, Search and Rescue (SAR) information and
other navigational information for NAVTEX receiver-equipped vessels sailing in
coastal waters.
The FURUNO NX-700 NAVTEX receiver receives NAVTEX messages and
automatically displays them together with station ID and message category
information.
If ship’s position data is fed from navigation equipment, the NX-700
automatically decides in which NAVAREA the vessel is navigating, and selects
stations. (NAVAREAs are geographical zones defined by the international
Maritime Organization.)
-Meets the following standards and regulations
MSC.148 (77) IMO A.694 (17)
IEC 61097-6 Ed.2 CDV (2005-02)
IEC 60945 Ed. 3 and 4
IEC 61162-1 and 2
EN 300 065V 1.1.3
EN 301 011V 1.1.1 (1998-09)
ITU-R M 540-2
ITU-R M 625-3
-Receives 518 kHz and another (490 or 4209.5 kHz) at the same time
-5” LCD display
-Prints out the message selected
-Bright 76 x 100 mm, monochrome LCD, 240 x 320 dots with adjustable contrast
and brilliance
-Low power consumption
-Displays the NAV data (date, own ship’s position, speed and course) or distance
(distance between own ship’s position and information mentioned in the
message) at the bottom of screen
v
TABLE OF CONTENTS
EQUIPMENT LISTS ........................................................................................... viii
SYSTEM CONFIGURATIONS .............................................................................. x
1. PRINCIPLE OF NAVTEX SYSTEM ............................................................... 1-1
1.1
1.2
1.3
1.4
1.5
How NAVTEX Works ................................................................................................. 1-1
NAVTEX System Operation....................................................................................... 1-1
Message Format ....................................................................................................... 1-2
NAVTEX Station Map ................................................................................................ 1-3
NAVTEX Station List.................................................................................................. 1-4
2. OPERATION................................................................................................... 2-1
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
Operating Controls .................................................................................................... 2-1
Turn the Unit On/Off .................................................................................................. 2-1
Adjusting LCD Dimmer.............................................................................................. 2-2
Confirming the New Message.................................................................................... 2-3
Sample Messages..................................................................................................... 2-4
Choosing the Receive Mode ..................................................................................... 2-5
Choosing the Local Frequency .................................................................................. 2-6
Editing the Setting for Station and Message .............................................................. 2-6
Switchings the Frequency to Display......................................................................... 2-8
Alarm Messages........................................................................................................ 2-8
Processing Messages ............................................................................................... 2-9
Printing Messages................................................................................................... 2-10
Editing the NAVTEX Station List .............................................................................. 2-12
Icons ....................................................................................................................... 2-15
Messages List ......................................................................................................... 2-16
Other Functions....................................................................................................... 2-17
3. MAINTENANCE & TROUBLESHOOTING ................................................... 3-1
3.1
3.2
3.3
3.4
3.5
Maintenance.............................................................................................................. 3-1
Replacement of Fuse, Battery, LCD and Thermal Paper ........................................... 3-2
Troubleshooting......................................................................................................... 3-4
Diagnostics................................................................................................................ 3-5
Restoring All Default Settings .................................................................................... 3-6
4. INSTALLATION .............................................................................................. 4-1
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Display Unit ............................................................................................................... 4-1
Receiver Unit............................................................................................................. 4-3
Antenna Unit ............................................................................................................. 4-4
Printer (NX-700B only) .............................................................................................. 4-5
Wiring........................................................................................................................ 4-5
Setting of Printer...................................................................................................... 4-10
Digital Interfacing......................................................................................................4-11
vi
MENU TREE.................................................................................................... AP-1
SPECIFICATIONS ........................................................................................... SP-1
PACKING LISTS ............................................................................................... A-1
OUTLINE DRAWINGS ...................................................................................... D-1
INTERCONNECTION DIAGRAM.......................................................................S-1
vii
EQUIPMENT LISTS
Standard Supply
Name
Display Unit
Receiver Unit
Antenna Unit
Installation
Materials
Spare Parts
Accessories
Type
NX-700A
NX-700B
NX-7001
NX-7H
CP08-01810
CP08-01820
CP08-01870
CP08-01880
CP08-01890
Code No.
000-040-180
000-040-210
000-040-350
000-040-362
000-040-363
CP08-01860
000-040-349
CP08-01863*
004-514-530
CP08-01864*
004-514-540
CP08-01861*
SP08-02101*
FP08-00800*
004-514-350
004-514-370
000-040-396
viii
Qty
1
1
1
Remarks
w/printer
w/o printer
10 m cable, CP08-01811*
20 m cable, CP08-01811*
1
30 m cable, CP08-01811*
40 m cable, CP08-01811*
50 m cable, CP08-01811*
DSUB25P cable, between
1
Display and Receiver Units
For Antenna Unit w/o antenna
1
cable
For Antenna Unit w/ antenna
cable.
1
For Display Unit
1
Fuse for Receiver Unit*
1
For NX-700A
*: See the back of this manual.
Optional Supply
Name
Thermal Paper
Flush Mount Kit
AC-DC Power
Type
TP058-30CL
OP08-19
OP08-20
PR-240-CE
Code No.
000-154-047
004-514-810
004-514-820
000-053-373
000-041-174
000-041-175
000-041-176
000-041-177
000-041-178
005-948-250
005-948-260
005-948-270
005-948-280
005-948-290
000-563-048
000-126-000
000-126-001
000-152-698
000-152-699
000-152-700
000-152-701
Qty
1 set
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
No.13-QA330
000-803-239
1
No.13-QA310
000-803-240
No.13-RC5160
000-806-114
CP20-01111
NX-700A
NX-700B
004-365-780
-
OP04-2
Extension Cable Kit
OP08-12
Coaxial Cable
RG-10/U-Y
Cable Assy
DSUB25P-DSUB25P
Right Angle Mounting
Base
L-Angle Mounting
Base
Handrail Mounting
Base
Mast Mounting Kit
Display Unit
ix
1
1
1
1
Remarks
For NX-700A
For NX-700A
For NX-700B
10 m, w/connector
20 m, w/connector
30 m, w/connector
40 m, w/connector
50 m, w/connector
10 m
20 m
30 m
40 m
50 m
30 m
40 m
50 m
3m
5m
10 m
15 m
For antenna unit NX-7H
SYSTEM CONFIGURATIONS
DISPLAY UNIT
NX-700A
DISPLAY UNIT
NX-700B
ANTENNA UNIT
NX-7H
or
Max. 15 m
Max. 100 m
RECEIVER UNIT
NX-7001
External Alarm
Rectifier
PR-240-CE
Printer (NX-700B only)
INS
(Integrated Navigation System)
or
Navigator
Power supply
100-115/
200-230 VAC.
1 , 50/60 Hz
Power supply
12-24 VDC
: Standard
: Option
: User supply
Environmental Category
Antenna unit
To be installed in an exposed area
Display unit
Receiver unit
To be installed in a protected area
x
1.
PRINCIPLE OF NAVTEX SYSTEM
1.1
How NAVTEX Works
NAVTEX is an acronym meaning Navigational Telex, and as its name shows, it is
a kind of narrow band radio teletype system for sending (by frequency shift
keying) text messages expressed in a 7-unit code. The difference is that a
NAVTEX transmitter transmits nine control characters (header code) ahead of
the main message, so that the receiver can identify the station, message type
and serial number automatically.
1.2
NAVTEX System Operation
For navigation purposes, the world is divided into 16 areas as shown in the
figure below. Each Navtex station has an identification code, from “A” to “Z”. The
frequency assigned to Navtex are 518 kHz and another (490 or 4209.5 kHz),
and many stations exist in the same service coverage.
If the stations were to transmit without any rule, the system would collapse due
to mutual interference. To avoid this problem, the following rules apply.
• The transmission schedule is determined so that two or more stations having
a common service area may not overlap in time.
• Each station transmits with minimum required power to cover its service area
(200 to 400 nautical miles nominal).
1-1
1. PRINCIPLE OF NAVTEX SYSTEM
1.3
Message Format
For automatic identification of messages, each message starts with nine control
characters, called “Header codes”.
The first five characters are always “ZCZC_“ and common to all messages. This
part is used for message synchronization. The latter four characters are
designed as B1, B2, B3 and B4 indicate origin, category and serial number of
the message.
Character B1 is the identification letter of the Navtex station “A” thru “Z”.
Character B2 indicates the type of message. “A” thru “Z”, as listed below.
Character B3 and B4 indicate the serial number of the message. The serial
numbers are counted up from “01” to “99”, and starts from “01” again. Number
“00” is specially reserved for important emergency messages.
The end of each message is indicated by “NNNN” (four successive N’s).
General message format is summarized below.
Header code
ZCZC
B1 B2 B3 B4
main message
Start code
(sync)
Main message
NNNN
Termination code
Serial number
"00": Emergency message
"01" - "99": Normal message
Type of message
"A" - "Z"
(See the list below.)
Station ID
"A" - "Z"
1-2
A:
[Type of message (category)]
Navigational warning
I:
Spare
B:
Meteorological warning
J:
SATNAV message
C:
Ice report
K:
Other electronic navigational aid
system message
D:
Search and rescue information/pirate L:
attack warnings
Navigational warning (addition to
“A”)
E:
Meteorological forecast
F:
Pilot message
G:
AIS
H:
LORAN message
V to Y
Special services allocation by the
NAVTEX Co-ordinating Panel
Z:
QRU (no message on hand)
1. PRINCIPLE OF NAVTEX SYSTEM
1.4
NAVTEX Station Map
1-3
1. PRINCIPLE OF NAVTEX SYSTEM
1.5
NAV
area
I
NAVTEX Station List
Latitude
Longitude
Freq.
Area Station
(kHz)
(nm)
ID
Broadcast schedule (UTC)
Belgium
Oostende
51 11 N
02 48 E
518
55
T
0310, 0710, 1110, 1510, 1910, 2310
Estonia
Tallinn
59 30 N
24 30 E
518
250
U
0320, 0720, 1120, 1520, 1920, 2320
Iceland
Reykjavik Radio
64 05 N
21 51 W
518
550
R
0250, 0650, 1050, 1450, 1850, 2250
490
550
R
0318, 0718, 1118, 1518, 1918, 2318
Ireland
Valentia
51 27 N
09 49 W
518
400
W
0340, 0740, 1140, 1540, 1940, 2340
Malin Head
55 22 N
07 21 W
518
400
Q
0240, 0640, 1040, 1440, 1840, 2240
France
Niton
50 35 N
01 18 W
518
270
K
0140, 0540, 0940, 1340, 1740, 2140
Netherlands
Den Helder
52 06 N
04 15 E
518
110
P
0230, 0630, 1030, 1430, 1830, 2230
Norway
Bodo Radio
67 16 N
14 23 E
518
450
B
0010, 0410, 0810, 1210, 1610, 2010
Rogaland Radio
58 48 N
05 34 E
518
450
L
0150, 0550, 0950, 1350, 1750, 2150
Vardoe Radio
70 22 N
31 06 E
518
450
V
0330, 0730, 1130, 1530, 1930, 2330
Svalbard
78 04 N
13 38 E
518
450
A
0000, 0400, 0800, 1200, 1600, 2000
Orlandet
63 40 N
09 33 E
518
450
N
0210, 0610, 1010, 1410, 1810, 2210
Bjuroklubb
64 28 N
21 36 E
518
300
H
0110, 0510, 0910, 1310, 1710, 2110
Gislovshammar
55 29 N
14 19 E
518
300
J
0130, 0530, 0930, 1330, 1730, 2130
Grimeton
57 06 N
12 23 E
518
300
D
0030, 0430, 0830, 1230, 1630, 2030
Cullercoats
55 02 N
01 26 W
518
270
G
0100, 0500, 0900, 1300, 1700, 2100
490
270
U
0320, 0720, 1120, 1520, 1920, 2320
Portpatrick
54 51 N
05 07 W
518
270
O
0220, 0620, 1020, 1420, 1820, 2220
490
270
C
0020, 0420, 0820, 1220, 1620, 2020
Niton
50 35 N
01 18 W
518
270
E
0040, 0440, 0840, 1240, 1640, 2040
490
270
I
0120, 0520, 0920, 1320, 1720, 2120
Oostende
51 11 N
02 48 E
518
150
M
0200, 0600, 1000, 1400, 1800, 2200
Cross Corsen
48 28 N
05 03 W
518
300
A
0000, 0400, 0800, 1200, 1600, 2000
490
300
E
0040, 0440, 0840, 1240, 1640, 2040
Niton
50 35 N
01 18 W
490
270
T
0310, 0710, 1110, 1510, 1910, 2310
Horta
38 32 N
28 38 W
518
640
F
0050, 0450, 0850, 1250, 1650, 2050
Monsanto
38 44 N
09 11 W
518
530
R
0250, 0650, 1050, 1450, 1850, 2250
490
530
G
0100, 0500, 0900, 1300, 1700, 2100
Coruna
43 21 N
08 27 W
518
400
D
0030, 0430, 0830, 1230, 1630, 2030
Tarifa
36 01 N
05 34 W
518
400
G
0100, 0500, 0900, 1300, 1700, 2100
Las Palmas
28 10 N
15 25 W
518
400
I
0120, 0520, 0920, 1320, 1720, 2120
Sweden
United
Kingdom
II
Station
Country
France
Portugal
Spain
(Continued on next page)
1-4
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
III
Country
Latitude
Longitude
Freq.
Area
Station
(kHz)
(nm)
ID
Broadcast schedule (UTC)
Bulgaria
Varna
43 04 N
27 46 E
518
350
J
0130, 0530, 0930, 1330, 1730, 2130
Croatia
Split radio
43 30 N
16 29 E
518
85
Q
0240, 0640, 1040, 1440, 1840, 2240
Cyprus
Cypradio
35 03 N
33 17 E
518
200
M
0200, 0600, 1000, 1400, 1800, 2200
Egypt
Alexandria
31 12 N
29 52 E
518
350
N
0210, 0610, 1010, 1410, 1810, 2210
Serapeum
30 28 N
32 22 E
4209.5
400
X
0750, 1150
France
Toulon
43 06 N
05 59 E
518
250
W
0340, 0740, 1340, 1540, 1940, 2340
490
250
S
0300, 0700, 1100, 1500, 1900, 2300
Greece
Iraklion
35 20 N
25 07 E
518
280
H
0110, 0510, 0910, 1310, 1710, 2110
Kerkyra
39 37 N
19 55 E
518
280
K
0140, 0540, 0940, 1340, 1740, 2140
Limnos
39 52 N
25 04 E
518
280
L
0150, 0550, 0950, 1350, 1750, 2150
Israel
Haifa
32 49 N
35 00 E
518
200
P
0020, 0420, 0820, 1220, 1620, 2020
Italy
Roma
41 48 N
12 31 E
518
320
R
0250, 0650, 1050, 1450, 1850, 2250
Augusta
37 14 N
15 14 E
518
320
V
0330, 0730, 1130, 1530, 1930, 2330
Cagliari
39 14 N
09 14 E
518
320
T
0310, 0710, 1110, 1510, 1910, 2310
Trieste
45 41 N
13 46 E
518
320
U
0320, 0720, 1120, 1520, 1920, 2320
Malta
Malta
35 49 N
14 32 E
518
400
O
0220, 0620, 1020, 1420, 1820, 2220
Russian
Federation
Novorossiysk
44 42 N
37 44 E
518
300
A
0300, 0700, 1100, 1500, 1900, 2300
Spain
Cabo de la Nao
38 43 N
00 09 E
518
300
X
0350, 0750, 1150, 1550, 1950, 2350
Turkey
Istanbul
41 04 N
28 57 E
518
300
D
0030, 0430, 0830, 1230, 1630, 2030
Samsun
41 17 N
36 20 E
518
300
E
0040, 0440, 0840, 1240, 1640, 2040
Antalya
36 53 N
30 42 E
518
300
F
0050, 0450, 0850, 1250, 1650, 2050
Izmir
38 22 N
26 36 E
518
300
I
0120, 0520, 0920, 1320, 1720, 2120
Mariupol
47 06 N
37 33 E
518
280
B
0100, 0500, 0900, 1300, 1700, 2100
Odessa
46 29 N
30 44 E
518
280
C
0230, 0630, 1030, 1430, 1830, 2230
Bermuda
32 23 N
64 41 W
518
280
B
0010, 0410, 0810, 1210, 1610, 2010
Riviere-au-Renard
50 11 N
66 07 W
518
300
C
D
0020, 0420, 0820, 1220, 1620, 2020
0035, 0435, 0835, 1235, 1635, 2035
Wiarton
44 20 N
81 10 W
518
300
H
0110, 0510, 0910, 1310, 1710, 2110
St. Johns
47 30 N
52 40 W
518
300
O
0220, 0620, 1020, 1420, 1820, 2220
Thunder Bay
48 25 N
89 20 W
518
300
P
0230, 0630, 1030, 1430, 1830, 2230
Sydney, NS
46 10 N
60 00 W
518
300
Q
0240, 0640, 1040, 1440, 1840, 2240
J
0255, 0655, 1055, 1455, 1855, 2255
Yarmouth
43 45 N
66 10 W
518
300
U
0320, 0720, 1120, 1520, 1920, 2320
V
0335, 0735, 1135, 1535, 1935, 2335
Ukraine
IV
Station
Bermuda
(UK)
Canada
(Continued on next page)
1-5
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
IV
Country
Canada
United States
Netherlands
Antilles
Freq.
Area
Station
(kHz)
(nm)
ID
518
300
X
0350, 0750, 1150, 1550, 1950, 2350
518
300
T
0310, 0710, 1110, 1510, 1910, 2310
490
300
S
0300, 0700, 1100, 1500, 1900, 2300
80 23 W
518
240
A
0000, 0400, 0800, 1200, 1600, 2000
41 43 N
70 30 W
518
200
F
0445, 0845, 1245, 1645, 2045, 0045
New Orleans
29 53 N
89 57 W
518
200
G
0300, 0700, 1100, 1500, 1900, 2300
Portsmouth
36 43 N
76 00 W
518
280
N
0130, 0530, 0930, 1330, 1730, 2130
Isabella
18 28 N
67 04 W
518
200
R
0200, 0600, 1000, 1400, 1800, 2200
Savannah, GA
32 08 N
81 42 W
518
200
E
0040, 0440, 0840, 1240, 1640, 2040
Curacao
12 10 N
68 52 W
518
400
H
0110, 0510, 0910, 1310, 1710, 2110
Station
Latitude
Longitude
Labrador
53 42 N
57 01 W
Iqaluit, NU
63 43 N
68 33 W
Miami
25 37 N
Boston
V
VI
NIL
Argentina
Ushaia
54 48 S
68 18 W
518
280
M
0200, 0600, 1000, 1400, 1800, 2200
Rio Gallegos
51 37 S
65 03 W
518
280
N
0210, 0610, 1010, 1410, 1810, 2210
45 51 S
67 25 W
518
280
O
0220, 0620, 1020, 1420, 1820, 2220
Bahia Blanca
38 43 S
62 06 W
518
280
P
0230, 0630, 1030, 1430, 1830, 2230
Mar del Plata
38 03 S
57 32 W
518
280
Q
0240, 0640, 1040, 1440, 1840, 2240
Buenos Aires
34 36 S
58 22 W
518
560
R
0250, 0650, 1050, 1450, 1850, 2250
Uruguay
La Paloma
34 40 S
54 09 W
518
280
F
0050, 0450, 0850, 1250, 1650, 2050
490
280
A
0000, 0400, 0800, 1200, 1600, 2000
Namibia
Walvis Bay
23 03 S
14 37 E
518
378
B
0010, 0410, 0810, 1210, 1610, 2010
South Africa
Cape Town
33 40 S
18 43 E
518
500
C
0020, 0420, 0820, 1220, 1620, 2020
Port Elizabeth
34 02 S
25 33 E
518
500
I
0120, 0520, 0920, 1320, 1720, 2120
Durban
30 00 S
31 30 E
518
500
O
0220, 0620, 1020, 1420, 1820, 2220
Mumbay
19 05 N
72 50 E
518
250
G
0100, 0500, 0900, 1300, 1700, 2100
Madras
13 08 N
80 10 E
518
400
P
0230, 0630, 1030, 1430, 1830, 2230
Mauritius
Mauritius Radio
20 10 S
57 28 E
518
400
C
0020, 0420, 0820, 1220, 1620, 2020
Bahrain
Hamala
26 09 N
50 28 E
518
300
B
0010, 0410, 0810, 1210, 1610, 2010
Egypt
Serapeum
30 28 N
32 22 E
518
200
X
0350, 0750, 1150, 1550, 1950, 2350
4209.5
200
X
0750, 1150
Kosseir
26 06 N
34 17 E
518
400
V
0330, 0730, 1130, 1530, 1930, 2330
Bushehr
28 59 N
50 50 E
518
300
A
0000, 0400, 0800, 1200, 1600, 2000
Bandar Abbas
27 07 N
56 04 E
518
300
F
0050, 0450, 0850, 1250, 1650, 2050
Comodoro
Rivadavia
VII
VIII
IX
Broadcast schedule (UTC)
India
Iran
(Continued on next page)
1-6
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
IX
Station
Country
Latitude
Longitude
Freq.
(kHz)
Area
(nm)
Station
ID
Saudi Arabia
Jeddah
21 23 N
39 10 E
518
390
H
0705, 1305, 1905
Oman
Muscat
23 36 N
58 30 E
518
270
M
0200, 0600, 1000, 1400, 1800, 2200
Pakistan
Karachi
24 51 N
67 03 E
518
400
P
0230, 0630, 1030, 1430, 1830, 2230
X
XI
Broadcast schedule (UTC)
NIL
China
Sanya
18 14 N
109 30 E
518
250
M
0200, 0600, 1000, 1400, 2200
Guangzhou
23 08 N
113 32 E
518
250
N
0210, 0610, 1010, 1410, 2210
Fuzhou
26 01 N
119 18 E
518
250
O
0220, 0620, 1020, 1420, 2220
Shanghai
31 08 N
121 33 E
518
250
Q
0240, 0640, 1040, 1440, 2240
Dalian
38 52 N
121 31 E
518
250
R
0250, 0650, 1050, 1450, 2250
Jayapura
02 31 S
140 43 E
518
300
A
0000, 0400, 0800, 1200, 1600, 2000
Ambon
03 42 S
128 12 E
518
300
B
0010, 0410, 0810, 1210, 1610, 2010
Makassar
05 06 S
119 26 E
518
300
D
0030, 0430, 0830, 1230, 1830, 2030
Jakarta
06 06 S
106 54 E
518
300
E
0040, 0440, 0840, 1240, 1640, 2040
Otaru
43 19 N
140 27 E
518
400
J
0130, 0530, 0930, 1330, 1730, 2130
Kushiro
42 57 N
144 36 E
518
400
K
0140, 0540, 0940, 1340, 1740, 2140
Yokohama
35 14 N
139 55 E
518
400
I
0120, 0520, 0920, 1320, 1720, 2120
Moji
34 01 N
130 56 E
518
400
H
0110, 0510, 0910, 1310, 1710, 2110
Naha
26 05 N
127 40 E
518
400
G
0100, 0500, 0900, 1300, 1700, 2100
Chukpyong
37 03 N
129 26 E
518
200
V
0330, 0730, 1130, 1530, 1930, 2330
490
200
J
0130, 0530, 0930, 1330, 1730, 2130
Pyongsan
35 36 N
126 29 E
518
200
W
0340, 0740, 1340, 1540, 1940, 2340
490
200
K
0140, 0540, 0940, 1340, 1740, 2140
Penang
05 26 N
100 24 E
518
350
U
0320, 0720, 1120, 1520, 1920, 2320
Miri
04 28 N
114 01 E
518
350
T
0310, 0710, 1110, 1510, 1910, 2310
Sandakan
05 54 N
118 00 E
518
350
S
0300, 0700, 1100, 1500, 1900, 2300
Singapore
Singapore
01 25 N
103 52 E
518
400
C
0020-0030, 0420-0430, 0820-0830,
1220-1230, 1620-1630, 2020-2030
Thailand
Bangkok Radio
13 43 N
100 34 E
518
200
F
0050, 0450, 0850, 1250
United States
Guam
13 29 N
144 50 E
518
100
V
0100, 0500, 0900, 1300, 1700, 2100
Indonesia
Japan
Korea,
Republic of
Malaysia
(Continued on next page)
1-7
1. PRINCIPLE OF NAVTEX SYSTEM
NAV
area
XI
Vietnam
Taiwan
Associate
Member of IMO
XII
Canada
United States
XIII
Freq.
Area
Station
(kHz)
(nm)
ID
518
400
X
0350, 0750, 1150, 1550, 1950, 2350
490
400
W
0340, 1540
4209.5
400
W
0230, 0630, 1030, 1430, 1830, 2230
108 13 E
518
400
K
0140, 0540, 0940, 1340, 1740, 2140
22 29 N
120 25 E
518
216
P
Hong Kong
22 13 N
114 15 E
518
400
L
0150, 0550, 0950, 1350, 1750, 2150
Prince Rupert
54 20 N
130 20 W
518
300
D
0030, 0430, 0830, 1230, 1630, 2030
Tofino
48 55 N
125 35 W
518
300
H
0110, 0510, 0910, 1310, 1710, 2110
San Francisco
37 55 N
122 44 W
518
350
C
0400, 0800, 1200, 1600, 2000, 2400
Kodiak
57 46 N
152 34 W
518
200
J
0300, 0700, 1100, 1500, 1900, 2300
Honolulu
21 22 N
158 09 W
518
350
O
0040, 0440, 0840, 1240, 1640, 2040
Cambria
35 31 N
121 03 W
518
350
Q
0445, 0845, 1245, 1645, 2045, 0045
Astoria
46 10 N
123 49 W
518
216
W
0130, 0530, 0930, 1330, 1730, 2130
Kholmsk
47 02 N
142 03 E
518
300
B
0010, 0410, 0810, 1210, 1610, 2010
Murmansk
68 46 N
32 58 E
518
300
C
0020, 0420, 0820, 1220, 1620, 2020
Arkhangelsk
64 51 N
40 17 E
518
300
F
0050, 0450, 0850, 1250, 1650, 2050
Astrakhan
45 47 N
47 33 E
518
250
W
0340, 0740, 1140, 1540, 1940, 2340
A
H
0400, 1200, 2000
0000, 0800, 1600
B
0410, 1210, 2010
I
0010, 0810, 1610
C
0420, 1220, 2020
J
0020, 0820, 1620
D
0430, 1230, 2030
K
0030, 0830, 1630
E
0440, 1240, 2040
L
0040, 0840, 1640
Station
Latitude
Longitude
Ho Chi Minh City
10 47 N
106 40 E
Haiphong
20 44 N
106 44 E
Danang
16 05 N
Kaohsiung
Country
Russian
Federation
XIV
XV
XVI
Broadcast schedule (UTC)
0230, 0630, 1030, 1430, 1830, 2230
NIL
Chile
Peru
Antofagasta
23 40 S
70 25 W
518
300
Valparaiso
32 48 S
71 29 W
518
300
Talcahuano
36 42 S
73 06 W
518
300
Puerto Montt
41 30 S
72 58 W
518
300
Punta Arenas
53 09 S
70 58 W
518
300
Isla de Pascua
27 09 S
109 25 W
518
300
Paita
05 05 S
81 07 W
518
Callao
12 03 S
77 09 W
Mollendo
17 01 S
72 01 W
F
0450, 1250, 2050
G
0050, 0850, 1650
200
S
0300, 0700, 1100, 1500, 1900, 2300
518
200
U
0320, 0720, 1120, 1520, 1920, 2320
518
200
W
0340, 0740, 1140, 1540, 1940, 2340
Note: The list shows the stations listed at Longwave Navtex Broadcasts (Oct. 2004).
1-8
2.
OPERATION
2.1
Operating Controls
Registers items on menus.
Cursor pad
-Shifts the cursor and display.
-Selects items on menus.
ENT
MENU
ESC
Opens menu/Returns to the previous display.
LIST
Opens the LIST options.
PRINT
Opens the PRINT options.
DIM
Turns the power on/off.
Adjusts the panel and LCD dimmer.
+: Raises the setting.
- : Decreases the setting.
Display unit, front view
2.2
Turning the Unit On/Off
key to turn the unit on. A beep sounds and the equipment shows
Press the
the start up display, where the ROM and RAM are checked for proper operation
and the program no. is displayed. The results of the check are shown as OK or
NG (No Good).
When the results are OK, the list display is shown after five seconds after
completion of the check, with frequency last used before turning the power off.
DUAL CHANNEL NAVTEX
NX-700
FURUNO ELECTRIC CO., LTD.
ROM : OK RAM : OK
Program No. 0850193-XX
XX: Program version No.
2-1
2. OPERATION
At the default setting, the equipment functions as below;
When the results of the check are OK, ALL MESSAGE display for 518 kHz
appears. This screen shows all messages received in 518 kHz.
You can switch 518 kHz (International message) and 490 kHz (local message) to
display. The NX-700A is preset to print all received message out.
All message display (518 kHz)
Note 1: To display all received messages in 490 kHz, press ◄ or ►.
Note 2: To cancel the printing all received messages out, see page 2-11.
To turn the power off, press the
key again.
Note: If NG appears for any test, try to press any key to go to the next stage.
The equipment, however, may not be operated properly. Contact your
dealer if the problem persists.
2.3
Adjusting LCD Dimmer
You can adjust LCD and panel dimmer with the + DIM – key. The adjustment
range is 0 (dark) to 9 (bright).
+: Raises the dimmer.
-: Decreases the dimmer.
2-2
2. OPERATION
2.4
Confirming the New Message
When you receive a new message, do one of the following depending on
message received.
SAR (Search and Rescue) message
1. When an SAR message is received, the audible alert sounds and details for
the SAR message appear.
Icon for SAR message
2. Press any key other than
key to silence the alarm.
Other messages
1. When a message other than an SAR message is received, the display shows
one of the following windows.
Received new int'l msg.
Received new local msg.
Display new msg ?
Yes No
Display new msg ?
Yes No
International message
Local message
2. If you want to read the message immediately, press ◄ to choose “Yes” and
then press the ENT key to display the message
To read the message later, choose “No”, and then press the ENT key to
close the window.
2-3
2. OPERATION
2.5
Sample Messages
Press ▲ or ▼ on the cursor pad to choose a message, and then press the ENT
key to show the detailed information for that message. The message list and
detailed message displays can be switched by pressing the ENT key.
Frequency (paragraph 2.9)
Station ID, type of message,
serial No. (two digits, paragraph 1.3)
Status icon (paragraph 2.14)
No. of saved messages
Error rate
Category of messages
(paragraph 2.11)
Receiving
date
New
ENT key
Old
Operation guide
Message icon (paragraph 2.14)
Message list
Detailed message
Note 1: The operation guide at the bottom of screen shows the functions of the
keys available for use with the current screen.
Note 2: The character size can be changed. For detail, see page 2-18.
Key
▲▼
◄►
MENU
ENT
LIST
PRINT
2-4
Display mode
List
Detailed
List
Detailed
List
Detailed
List
Detailed
List
Detailed
List
Detailed
Function
Scrolls the list.
Scrolls the message.
Switches the international and local lists.
Shows the newer (◄) or older (►) message.
Shows the main menu.
Shows the detailed message selected.
Shows the message list.
Shows the list options.
Shows the print options.
2. OPERATION
2.6
Choosing the Receive Mode
The NAVTEX menu allows you to select what station to receive, automatically,
manually. The Auto mode requires navigation data, and stations are
automatically selected according to the distance between own ship and NAVTEX
stations. If navigation data is not input, all stations are selected. The manual
mode lets you freely stations to receive. The INS mode allows you to set the
station, message and local channel from the external equipment (ex. Integrated
Navigation System, using NMK sentence) connected.
1. Press the MENU/ESC key to show the main menu.
Menu
NAVTEX
System
Display
Service
Main menu
2. Press ▲ or ▼ to choose NAVTEX.
3. Press the ENT key or ► to open the NAVTEX menu.
NAVTEX
Receive Mode Manual
Local Channel 490kHz
Auto Print
All
Rcv Station & Msg
User Select Station & Msg
NAVTEX menu
4. Press ▲ or ▼ to choose Receive Mode, and then press the ENT key or ► to
show the receive mode options.
INS
Auto
Manual
Receive mode options
5. Press ▲ or ▼ to choose INS, Auto or Manual as appropriate, and then press
the ENT key.
6. Press the MENU/ESC key several times to close the menu.
2-5
2. OPERATION
2.7
Choosing the Local Frequency
You can choose 490 kHz or 4209.5 kHz as the local frequency. This function is
only available for the Auto and Manual modes. (See paragraph 2.6.)
1. Press the MENU/ESC key to show the main menu.
2. Press ▲ or ▼ to choose NAVTEX, and then press the ENT key or ►.
3. Press ▲ or ▼ to choose Local Channel, and then press the ENT key or ► to
show the local channel options.
490kHz
4209.5kHz
Local channel options
4. Press ▲ or ▼ to choose the frequency 490 kHz or 4209.5 kHz, and then
press the ENT key.
5. Press the MENU/ESC key several times to close the menu.
2.8
Editing the Settings for Station and Message
Stations and messages for receiving/displaying on each station (message) can
be edited as below.
Rcv Station & Msg
Station
You can receive messages by station when Manual is chosen as the Receive
Mode on the NAVTEX menu.
Message
You can choose the messages to receive when Manual or Auto is chosen as the
Receive Mode on the NAVTEX menu. Note that A/B/D/L cannot be rejected.
User Select Station & Msg
Station
Choose the station to display on User Selected Messages, which is shown when
the LIST key is pressed.
Message
Choose the type of message to display on User Selected Messages, which is
shown when the LIST key is pressed.
Note 1: For messages, the alarm message is displayed always.
Note 2: When User Select is chosen as the Auto Print on NAVTEX menu, only
the messages chosen here are printed. (See paragraph 2-11.)
1. Press the MENU/ESC key to show the main menu.
2. Press ▲ or ▼ to choose NAVTEX, and then press the ENT key.
2-6
2. OPERATION
3. Press ▲ or ▼ to choose “Rcv Station & Msg” or “User Select Station & Msg”.
4. Press the ENT key to open the appropriate editing window. (Below is the Rcv
Station & Msg editing window.)
Recieve mode
Rcv Station & Msg
Internaitional frequency
Station
[Auto]
[518]
Station
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Message
Message
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Local frequency*
[490]
Station
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Message
Changeable item
ABCDEFGHIJKLMNOPQRSTUVWXYZ
[ ][ ] MOVE
[ENT] EDIT [MENU] RETURN TO MENU
*: Local channel selected at Paragraph 2.7.
Edit window (ex. Rcv Station & Msg)
5. Press ▲ or ▼ to choose the item to edit, and then press the ENT key to
show the alphabet selection window.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
Cursor
6. Press ◄ or ► to choose the alphabet desired, and then press ▲ or ▼ to
choose to receive or not.
The alphabet you have chosen not to receive is marked with “-“ (hyphen).
7. Press the ENT key
8. Repeat steps 5 through 7 to complete.
9. Press the MENU/ESC key to close the window.
2-7
2. OPERATION
2.9
Switching the Frequency to Display
With showing the message list, you can switch the frequency to 518 kHz or 490
(or 4209.5) kHz by pressing ◄ or ► key.
Press
490 (4209)
518
Switching the frequency to display
2.10
Alarm Messages
The sequence of events when an alarm message is received is as shown below.
When receiving SAR (Search and Rescue) message:
The audible alarm beep sounds, and the SAR message is shown. Note that All
Messages list appears if other list option is chosen when the ENT key is pressed.
(See paragraph 2.11.)
When receiving WARNING message (A/B/L):
When the Warn Msg Alm on System menu is set to On, the audible alarm
sounds and the message for receiving appears.
Silencing audible alarm
Press any key (except
2-8
key).
2. OPERATION
2.11
Processing Messages
Choosing messages to display
You can choose which category of messages to display: All, Alarm, User
Selected and Good messages.
1. With the message list or detailed message shown, press the LIST key to
show the list options.
All Messages
Alarm Messages
User Messages
Good Messages
Lock Message
List options
2. Press ▲ or ▼ to choose the item.
All Messages: Shows all messages received.
Alarm Messages: Shows only SAR/WARNING messages.
User Selected Messages: Shows messages arranged at User Select Station &
Msg on NAVTEX menu.
Good Messages: Shows messages whose error rate is less than 4%.
3. Press the ENT key to close the window.
The list chosen at step 2 appears.
Note: When the following messages appear, set the List window to All Messages
to show.
Urgent message:
“Message not chosen for display received; it is a int’l (or local) 00 message.
Choose “All Message” (LIST menu) to display.”
Normal message:
Int’l (or local) message not chosen for display received. Choose “All
Message” (LIST menu) to display.”
2-9
2. OPERATION
Protecting message from deleting
Messages are automatically deleted from the memory under the following
conditions.
-66 hours passed from the moment when received.
-Older than No. 200
To prevent a message from being deleted, do the follows;
1. Choose the message at the list display.
2. Press the LIST key to show the list options.
All Messages
Alarm Messages
User Messages
Good Messages
Lock Message
List options
3. Choose Lock Message from the list window.
The protect icon ( ) appears next to the message selected.
Note 1: To unlock a message, choose it and then select Unlock Message in the
list window. (The protect icon disappears.)
Note 2: When you unlock a message which was received 66 hours ago or a
message that is older than No. 200, it will be deleted promptly when
unlocked.
Note 3: Maximum each 50 messages for International and local (or 25% of each
memory) can be protected.
2.12
Printing Messages
Received messages can be printed automatically or manually, from the built-in
printer (NX-700A) or external printer (NX-700B).
Printing all messages displayed
All messages chosen on paragraph 2.11 can be printed out.
1. Press the PRINT key with showing all messages.
Print
Cancel Print
Print options
2. Press ▲ or ▼ to choose “Print”.
3. Press the ENT key to print.
Note: When a message is received while printing some messages, the new one
cannot be printed.
2-10
2. OPERATION
Printing each message
1.
2.
3.
4.
5.
Press ▲ or ▼ to choose the desired message from the list.
Press the ENT key to show the detailed information.
Press the PRINT key.
Press ▲or ▼ to choose “Print” from the window.
Press the ENT key to print.
Printing messages automatically
When receiving a message, it can be printed out immediately.
1. Press the MENU/ESC key to open the main menu.
2. Press ▲ or ▼ to choose NAVTEX, and then press the ENT key to show the
NAVTEX menu.
3. Press ▲ or ▼ to choose Auto Print, and then press the ENT key to open the
auto print options.
Off
All
User Select
Auto print options
4. Press ▲ or ▼ to choose All, User Select or Off as appropriate.
All: Prints all messages when receiving.
User Select: Prints only the specified messages at User Select Station & Msg
on the NAVTEX menu when receving.
Off: All messages are not printed automatically.
5. Press the ENT key.
6. Pres the MENU/ESC key several times to close the menu.
Canceling printing
When a menu is displayed, you cannot cancel the printing.
1. Press the PRINT key while showing the messages to open the print window.
2. Press ▼ to choose “Cancel Print” and then press the ENT key.
2-11
2. OPERATION
2.13
Editing the NAVTEX Station List
Maximum 300 NAVTEX stations can be registered into the memory.
Note: To cancel editing of a NAVTEX station, press the MENU/ESC key. The
message “Exit without saving?” appears. Choose “Yes”, and then press
ENT key.
Adding NAVTEX station
You may add a NAVTEX station to the NAVTEX station list as follows:
1. Press the MENU/ESC key to show the main menu.
2. Press ▲ or ▼ to choose Service, and then press the ENT key.
Service
INS Input Speed
4800bps
INS Output Speed 4800bps
Print Header
On
Edit Station List
Default Setting
Test
Rcv Monitor
Service menu
3. Press ▲ or ▼ to choose Edit Station List, and then press the ENT key.
Frequency
NAV Area
Station name
518kHz
NavArea
01
[ New ]
Oostende
Tallinn
Reykjavik Radio
Valentia
Malin Head
Niton
Den Helder
Bodo Radio
Rogaland Radio
Vardoe Radio
Svalbard
T, - , U, - , R, - , W,- , Q, - , K, - , P, - , B, - , L, - , V, - , A, - , -
[ ][ ] CHANGE NAVAREA
[LIST] CHANGE FREQ
[ENT] EDIT [MENU] RETURN TO MENU
Edit station list display
4. Confirm that New is chosen, and then press the ENT key to show the
addition window appears.
2-12
2. OPERATION
NAV Area
Station Name
Latitude
Longitude
Station ID
Sertvice Area
NavArea
Station
Latitude
Longitude
518kHz
490kHz
4209.5kHz
Range
1
0 00'N
0 00'E
ID1: - ID2: - ID3: ID1: - ID2: - ID3: ID1: - ID2: - ID3: 400nm
Save data ?
New addition window
5. Confirm that NavArea is chosen, and then press the ENT key to show the
area No. window.
6. Press ▲ or ▼ to choose a Nav area No. (1 to 16, and EXT), and then press
the ENT key.
For NAV area No., see paragraph 1.4. EXT is reserved for future use.
7. Confirm that Station is chosen, and then press ENT key.
8. Enter a station name (Max. 18 characters), and then press the ENT key.
a) Press ▲ or ▼ to choose a character. Each press of ▲ shows A -> … -> Z ->
a -> … -> z -> 0 -> … -> 9 -> _ -> - -> space in that sequence.
b) Press ► to move the cursor to next digit.
c) Repeat steps a) and b) to complete the station name.
9. Confirm that Latitude is chosen, and then press the ENT key.
10. Enter the latitude for station, and then press the ENT key.
Use ▲ or ▼ to switch to North and South.
11. Confirm that Longitude is chosen, and then press the ENT key.
12. Enter the longitude for station, and then pres the ENT key.
Use ▲ or ▼ to switch to East and West.
13. Choose 518kHz, 490kHz or 4209.5kHz, and then press the ENT key.
14. Enter the station ID (A to Z), and then press the ENT key.
For multiple stations, fill in ID2 and ID3.
15. Confirm that Range is chosen, and then press the ENT key.
16. Enter the service area (1 to 999 nm), and then press the ENT key.
17. Confirm that Save data? is chosen, and then press the ENT key.
The message “Save new station?” appears.
18. Press ◄ to choose “Yes”, and then press ENT key to close the new addition
window disappears.
Note: If the station ID was not entered at step 14, the message “Enter ID
data.” appears. Press any key, and then enter the station ID.
19. To enter another NAVTEX station, repeat steps 4 through 18.
20. Press the MENU/ESC key several times to close the menu.
2-13
2. OPERATION
Editing NAVTEX station
Existing NAVTEX station may be edited as follows:
1.
2.
3.
4.
5.
Press the MENU/ESC key to show the main menu.
Press ▲ or ▼ to choose Service, and then press the ENT key.
Press ▲ or ▼ to choose Edit Station List, and then press the ENT key.
Press ◄ or ► to choose the NAV area to be changed (01 to 16, EXT).
Press the LIST key to choose the frequency to be changed (518kHz, 490kHz
or 4209.5kHz).
6. Press ▲ or ▼ to choose the station, and then press the ENT key.
Edit
Delete
7. Press ▲ to choose “Edit”, and then press ENT key to show the edit window
appears.
Oostende
NAV Area
Station Name
Latitude
Longitude
Station ID
Service Area
NavArea
1
Station
Oostende
Latitude
51 11'N
Longitude
2 48'E
518kHz
ID1: T ID2: - ID3: 490kHz
ID1: - ID2: - ID3: 4209.5kHz ID1: A ID2: - ID3: Range
55nm
Save data ?
Edit window (Ex. NAVTEX station Oostende)
8. Edit data as appropriate.
9. Confirm that Save station? is chosen, and then press the ENT key.
10. Press ◄ to choose “YES”, and then press the ENT key to erase the edit
window.
11. Press the MENU/ESC key several times to close the menu.
Deleting NAVTEX stations
You may delete unnecessary NAVTEX stations as follows:
1.
2.
3.
4.
5.
Press the MENU/ESC key to show the main menu.
Press ▲ or ▼ to choose Service, and then press the ENT key.
Press ▲ or ▼ to choose Edit Station List, and then press the ENT key.
Press ◄ or ► to choose the NAV area to be deleted. (01 to 16, EXT).
Press the LIST key to choose the frequency to be deleted (518kHz, 490kHz
or 4209.5kHz).
6. Press ▲ or ▼ to choose the station name to be deleted, and then press ENT
key.
The item window appears.
2-14
2. OPERATION
Edit
Delete
7. Press ▲ or ▼ to choose Delete, and then press the ENT key.
The message “Delete station?” appears.
8. Press ◄ to choose “Yes”, and then press the ENT key to close the edit
window.
9. Press the MENU/ESC key several times to close the menu.
2.14
Icons
The NX-700 shows various icons to denote equipment status, and these are as
shown in the table below.
Icon
Status
Meaning
Status icon (shown at the tip of display)
Blinking
L1
Blinking
L2
Blinking
I
Blinking
L1
Blinking
L2
Blinking
Shows that an International frequency (518 kHz)
message has not been read.
Shows that a Local frequency message has not
been read.
L1: 490 kHz, L2: 4209.5 kHz
Appears while receiving a message.
I: International frequency (518 kHz)
L1: 490 kHz
L2: 4209.5 kHz
Lighting
Displayed when the voltage of the internal battery is
low. The message “Battery error” also appears on
the display.
X
Lighting
Print error (no paper, not connected to the printer,
etc.). The message “Printer error” also appears on
the display.
P
R
Lighting
While printing.
Message icon (shown next to messages)
NEW
SAR
!!
Lighting
Displayed when message is displayed for the first
time.
(This icon disappeared after showing the detail or 24
hours has passed.)
Lighting
Displayed when message type D (SAR) is displayed.
Lighting
Appears when message type A, B or L (Warning) is
displayed.
Lighting
Protected message
2-15
2. OPERATION
2.15
Messages List
In addition to the message “Received new local (int’l) msg.” the following
message-related messages may appear on the display.
Message
New message received.
Oldest message deleted to
free up memory.
Same message with lower
error rate received.
Currently displayed
message will be deleted.
Term of validity expired.
Currently displayed
message will be deleted.
Message not chosen for
display received; it is a int’l
00 message. Choose “All
Message”(LIST menu) to
display.
Message not chosen for
display received; it is a
local 00 message. Choose
“All Message”(LIST menu)
to display.
Int’l message not chosen
for display received.
Choose “All
Message”(LIST menu) to
display.
Local message not chosen
for display received.
Choose “All
Message”(LIST menu) to
display.
2-16
Meaning
Appears when the oldest
message is deleted to
make space for the latest
one.
Appears when two
messages have the
same ID are received
and the latter’s error rate
is lower than the former.
Appears when 66 hours
has passed after
receiving the currently
displayed message.
Appears when receiving
an international message
not specified for display
(00) at the SELECT
MESSAGES display.
Appears when receiving
a local message not
specified for display (00)
at the SELECT
MESSAGES display.
Appears when receiving
an international message
not specified for display
(Normal) at the SELECT
MESSAGES display.
Appears when receiving
a local message not
specified for display
(Normal) at the SELECT
MESSAGES display.
Remedy
Press any key.
Press any key.
Press any key.
Press any key, and then
choose All Message in
the List window.
2. OPERATION
2.16
Other Functions
This paragraph describes the various options which allow you to set up your unit
to suit your needs.
NAVTEX menu
Item
Receive
Mode
Local
Channel
Auto Print
Description
Chooses the receiving mode. (See
paragraph 2.6.)
Chooses the local channel.
Chooses the message to print
automatically. (See paragraph 2.12.)
Rcv Station & Receives messages in the category.
Msg
User Select
Sets the station and type of message to
be shown on the SELECT MESSAGES
Station &
Msg
display.
Setting
INS, Auto, Manual
490kHz, 4209.5kHz
Off, All, User Select
-
System menu
Item
Description
Turns the audible alarm on/off when receiving a
Warn Msg Alm
Warning message (A, B, and L).
Turns the audible alarm for monitoring of Rx
signal on/off.
Signal Monitor Off: Disables monitoring.
Int’l: Monitors international frequency.
Local: Monitors local frequency.
Key Beep
Turns key beep on/off.
If a GPS receiver feeds nav data to the NAVTEX,
you may use local time instead of UTC time.
Time Offset
Enter the time difference between local time and
UTC time.
Units
Printer
Setting
On, Off
Off, Int’l, Local
On, Off
-13:30 to
+13:30
nm, kt,
Chooses units of measurement (distance and
km, km/h,
ship speed) to be shown on the User Display.
mi, mi/h
None,
NX-700A,
Sets the printer type. (See paragraph 4.6.)
Upright,
Inverted
2-17
2. OPERATION
Display menu
Item
Scrolling
Description
Selects the speed of scrolling by pressing ▲ or ▼.
Slow: Scrolls by one line.
Fast: Scrolls by half of screen.
Skips to $$:
Scrolls line by line in list display; Skips to $$ position in detailed
display.
Font Size
Selects the size of characters.
Time Display
Selects the time format.
Setting
Slow, Fast,
Skip to $$
Small,
Medium,
Large
24 hour,
12 hour
Selects the date format.
MMM DD YYY,
Date Display
DD MMM YYYY,
YYYY MMM DD
Selects the type of data as user display to be shown at the
bottom of the display.
Nav Data
Date
Own ship's
position
Ship's speed
MAY 07 2005
00:00:18
12 34. 001 ' N
123 45. 001 ' E
SOG 1. 6 kt
COG 56. 9
Course
[ ][ ] SCROLL
[ ][ ] CHANGE FREQ
[MENU] MENU
[ENT] SHOW MESSAGE
[LIST] LIST MENU [PRINT] PRINT MENU
User Display
Off,
Nav Data,
Distance
Distance
Distance between the positions shown in the message and
own ship's when receiving.
DISTANCE
23.4nm
[ ][ ] SCROLL
[ ][ ] CHANGE FREQ
[MENU] MENU
[ENT] SHOW MESSAGE
[LIST] LIST MENU [PRINT] PRINT MENU
Speed
Display
Contrast
2-18
Selects the speed format to be displayed.
SOG: Speed Over Ground
STW: Speed Through Water
Sets the display contrast.
SOG, STW
0 to 9
2. OPERATION
Service menu
Item
INS
Input
Speed
INS
Output
Speed
Print
Header
Description
Setting
4800,
9600,
Selects the data transmission speed at which to input data
19200,
from INS.
38400
bps
4800,
9600,
Selects the data transmission speed to output data to the INS. 19200,
38400
bps
Turns the header (Own ship’s position, date, frequency, error
rate and distance information when receiving a message) for
printing on/off.
Receiving date
Own ship's poisition
when receiving
518kHz
Error Rate: 0.0%
Received MAY 07 2005 01:12:53
Position
34 28'N
134 03'E
Distance
23.4nm
Header
On, Off
ZCZC AA10
Distance between the positions shown in the messasge
and own ship's when receiving.
Edit
Edits/deletes stations. (See paragraph 2.13.)
Station
List
Default Restores all default settings. (See paragraph 3.5.)
Settings
Test
Starts the diagnostic test. (See paragraph 3.4.)
Shows the status for International and Local receiving.
-
-
International
message
Rcv
Monitor
Local message
-
2-19
2. OPERATION
This page is intentionally left be blank.
2-20
3.
MAINTENANCE &
TROUBLESHOOTING
This chapter provides information necessary for keeping your unit in good
working order and remedying simple problems.
WARNING
Do not open the equipment.
Hazardous voltage which can
cause electrical shock exists
inside the equipment. Only
qualified personnel should
work inside the equipment.
3.1
Maintenance
Regular maintenance is important for optimum performance. A maintenance
program should be established and should at least include the items shown in
the table below.
Maintenance program
Item
Check point
Remedy
Display unit connectors
Check for tight connection.
Tighten loosened connectors.
LCD
The LCD will, in time,
accumulate a coating of dust
which tends to dim the picture.
Wipe LCD lightly with soft
cloth to remove dust.
Wipe the LCD carefully to
prevent scratching, using
tissue paper and an LCD
cleaner. To remove dirt or salt
deposits, use an LCD cleaner,
wiping slowly with tissue
paper so as to dissolve the dirt
or salt. Change paper
frequently so the salt or dirt
will not scratch the LCD. Do
not use solvents such as
thinner, acetone or benzene
for cleaning.
Ground terminal
Check for tight connection and Clean or replace ground wire
corrosion.
as necessary.
3-1
3. MAINTENANCE & TROUBLESHOOTING
3.2
Replacement of Fuse, Battery and Thermal
Paper
Fuse
The fuse inside the receiver unit protects the equipment from overcurrent or
reverse polarity. If the fuse blows, contact your dealer about replacement.
Name
Fuse
Type
FGMB 2A 125V
Code No.
000-103-165
WARNING
Use the proper fuse.
Use of a wrong fuse can result in damage
to the equipment or cause fire.
Battery
A battery is installed inside the display unit, and it preserves data when the
power is turned off. The life of the battery is about 5-10 years, and its voltage is
checked when the power is turned on. When its voltage is low, the BATTERY
) icon appears on the display to alert you. When this happens, contact your
(
dealer to request replacement of the battery.
Note: When the battery is dead, all default settings are restored.
Name
BATT
Type
Code No.
CR2450-F2ST2L 000-144-941
WARNING
Ensure battery polarity is correct.
Wrong polarity may cause the batteries to
explode.
LCD Display
The life of the LCD is approx. 20,000 hour. When the LCD has expired, the
brilliance cannot be raised.
3-2
3. MAINTENANCE & TROUBLESHOOTING
Thermal paper (NX-700A only)
When the thermal paper runs out completely, the message “Printer error” (center
of screen) and the X icon (at the right-hand top corner) appear. Replace the
paper as follows.
Name
Thermal paper
Type
TP058-30CL
Code No.
000-154-047
1. Turn off the power.
2. Press the button shown below to open the paper holder cover.
Eject button
3. Peel the tape from the end of new paper.
Tape
4. Set the new paper in the paper container in the direction shown below.
Paper holder
New paper
Paper holder cover
5. Pull the end of the paper by 2 to 3 cm (as shown above), and then close the
cover.
3-3
3. MAINTENANCE & TROUBLESHOOTING
3.3
Troubleshooting
This section provides simple troubleshooting procedures which the user can
follow to restore normal operation. If you cannot restore normal operation do not
attempt to check inside the unit. Any trouble should be referred to a qualified
technician.
If . . .
then . . .
-ask serviceman to replace the blown
fuse.
you cannot turn on the power
-check battery for proper voltage
output.
the equipment receives unwanted
confirm that “Manual” is chosen at
messages.
Receive Mode on the NAVTEX menu.
check equipment by the diagnostic
test.
check the broadcasting schedule.
NAVTEX signal cannot be received.
check that the D-sub connector is
firmly fastened.
check that the antenna cable is firmly
fastened.
paper does not advance. (NX-700A only)
load paper correctly.
paper feeds but no recording. (NX-700A
check if correct thermal paper is being
only)
used.
keep the paper in a well-ventilated and
paper has darkened. (NX-700A only)
cool place.
check the setting of Printer on the
System menu.
check the printer cable.
the recording is not proper for the external check that the power of printer is
printer. (NX-700B only)
turned on and status is
“SELET/READY”.
check that the printer is available.
check that paper is set properly.
3-4
3. MAINTENANCE & TROUBLESHOOTING
3.4
Diagnostics
The memory test checks ROM, RAM, data port, battery, keyboard and LCD for
proper operation and displays program version numbers.
1. Press the MENU/ESC key to open the main menu.
2. Press ▼ to choose Service, and then press the ENT key.
3. Press ▲ or ▼ to choose Test, and then press the ENT key.
The message “Start test?” appears.
4. Press ◄ to choose “Yes”, and then press the ENT key.
Memory Test
Program No
Boot
ROM
SRAM
DRAM
CPU RAM
EEPROM
Battery
: 0850193-01.*
: 0850192-01.*
: OK
: OK
: OK
: OK
: OK
: OK (3.2V)
Hit any key.
*: Program version no.
Memory test
For any NG (No Good), contact your dealer.
5. When the message “Hit any key.” appears at the bottom of screen, press any
key (except
key) to show the key test screen.
Key Test
If there is no operation for
10 s, the screen changes.
Key test
6. Press each key (except
key) one by one.
A key is functioning properly if its on-screen location fills in black when the key is
pressed.
7. After all keys have been tested or no key is pressed after 10 seconds, the
equipment starts the LCD test by showing the white and black display (level
0 to 9).
3-5
3. MAINTENANCE & TROUBLESHOOTING
8. When the message “Hit any key” appears on the screen, press any key
(except
key) to show the Rx test screen.
The alarm for receiving monitor sounds while the Rx test is being conducted.
Also the test message is printed when the item other than “None” at Printer on
System menu.
Rx test
9. When the message “Hit any key.” appears on the screen, press any key
(except
key) or wait for one minute with no operation to finish.
10. Press the MENU/ESC key several times to close the menu.
3.5
Restoring all Default Settings
This operation restores all default settings. The following two settings, however,
are not disturbed.
-Received messages
-NAVTEX stations list (See paragraph 2.13.)
1. Press the MENU/ESC key to show the main menu.
2. Press ▼ to choose Service, and then press the ENT key.
3. Press ▲ or ▼ to choose Default Setting, and then press ENT key.
The message “Restore default settings?” appears.
4. Press ◄ to choose “Yes”, and then press the ENT key.
The Service menu appears.
5. Press the MENU/ESC key several times to close the menu.
3-6
4.
INSTALLATION
4.1
Display Unit
The display unit can be installed on a tabletop, on the overhead, or in a panel.
Refer to the outline drawings at the back of this manual for installation
instructions. When selecting a mounting location, keep in mind the following
points.
• Locate the unit away from exhaust pipes and vents.
• Locate it of direct sunlight, (or in a suitable, ventilated enclosure) to prevent
heat which can build up inside the cabinet.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Allow sufficient maintenance space at the sides and rear of the unit and leave
sufficient slack in cables, to facilitate maintenance and servicing.
• Compass safe distances are:
NX-700A (Standard: 1.45 m, Steering: 0.95 m)
NX-700B (Standard: 0.30 m, Steering: 0.30 m)
Tabletop, overhead mounting
1. Fix the hanger by using four self-tapping screws (5x20).
2. Screw knob bolts in display unit, set it to the hanger, and tighten the knob
bolts.
Note: For the overhead mounting, reinforce the mounting location for the weight
of the display unit (NX-700A: 3.3 kg, NX-700B: 0.7 kg) and secure the
hanger, with bolts, nuts and washers (local supply).
NX-700A
NX-700B
4-1
4. INSTALLATION
Flush mounting
The display unit can be installed flush mounted in a console or panel by using
the optional flush mount kit.
.
(For NX-700A)
Type: OP08-19
Code No.: 004-514-810
Name
Type
Code No.
Qty Remarks
Mounting metal
08-023-1019 100-326-960
1
Self-tapping screw
5X20
000-802-081
6
Hex. bolt
M8x15
000-862-144
2
Spring washer
M8
000-864-262
2
1. Cut out a hole with dimensions as shown below in the mounting location.
156+1
30+1
168+0.5
284+0.5
7
7
275+1
4
Fixing hole
2. Attach the fixing metal to the display unit with two hex. bolts (M8x15,
supplied with optional kit) and spring washers (supplied with optional kit).
3. Fasten six self-tapping screws to fix the display unit to the mounting location.
144+1
155+0.5
(For NX-700B)
Type: OP08-20
Code No.: 004-514-820
Name
Type
Code No.
Qty
Remarks
Mounting metal
08-023-2011 100-327-010 1
Self-tapping screw 5x20
000-802-081 4
Pan head screw
M4x12
000-802-130 4
1. Cut out a hole with dimensions as shown below in the mounting location.
156+1
155+0.5
4
Fixing hole
2. Attach the fixing metal to the display unit with four pan head screws (M4X12,
supplied with the optional kit).
3. Fasten four self-tapping screws (supplied with the optional kit) to fix the
display unit to the mounting location.
4-2
4. INSTALLATION
Receiver Unit
General mounting considerations
• The mounting location should be well ventilated and dry.
• The unit can be mounted on bulkhead or the desk.
• Secure the maintenance space shown in drawing at the back of this manual
for ease of maintenance and service.
• Compass safe distances are:
Standard: 1.15 m, Steering: 0.75 m
Mounting Method
Fasten the receiver unit with four self-tapping screws (5x20, supplied as
installation material). For bulkhead mounting, do the follows.
1. Tighten lower self-tapping screws so there is 5 mm clearance between
bottom of screw head and bulkhead.
2. Hook the receiver unit on the lower screws.
3. Tighten upper screws followed by the lower screws.
210+1
205+1
Fixing hole 2- 6
8
4.2
6
210+1
Notch
4-3
4. INSTALLATION
4.3
Antenna Unit
Mounting considerations
Install the antenna unit referring to the antenna installation diagram at the back
of this manual. When selecting a mounting location for the antenna unit, keep in
mind the following points:
• Do not shorten the antenna cable.
• The NX-700 contains a very sensitive receiver. To avoid mutual interface with
other radio equipment, do not install this unit near an SSB/VHF/CB
radiotelephone.
Coat here with silicone sealant to
prevent breakage of the cable by
vibration.
Wrap the vinyl sheet to prevent
the breakage of the cable, and
then fix the hose clamp.
4-4
4. INSTALLATION
4.4
Printer (NX-700B only)
Prepare the printer by locally as shown below for the NX-700B.
-8 bit parallel Centronics interface, or serial RS-232C
-Serial printer
-Baud Rate: 9600 bps
-Character length: 8 bit
-Parity: No
-Flow control: Xon/Xoff
-32 characters/line or more
4.5
Wiring
Display unit
NX-700A or B
Antenna ubit
NX-7H
Ground wire
IV-1.25sq (Local supply)
Antenna cable
04S4168 10/20/30/40/50m
DSUB25P-DSUB25P cable
(3m)
Ground wire
IV-1.25sq (Local supply)
Receiver unit
NX-7001
Power cable
DPYC-2.5
(Local supply)
-INS or Navigator
-Printer (for NX-700B only)
-Alarm
12-24VDC
4-5
4. INSTALLATION
Receiver unit
All cables are gathered to the receiver unit. Connect cables at inside of the
receiver unit as shown below.
RCV Board
08P3227
TB401 TB402
(+) (-)
J402*
1
2
3
4
5
J403
6
1
2
3
4
5
6
7
8
J401
Antenna cable
(to Antenna unit)
TTYCS-1Q
(to Navigator
or INS )
DPYC-2.5
(to ship's battery)
Printer cable
(to Printer, NX-700B only)
DPYC-1.5
(to External alarm)
DSUB25P-DSUB25P-3M cable
(to Display unit)
Receiver unit, inside view
Use the following JIS cable (Japan Industrial Standard) or equivalent to connect
power source, INS and external alarm appropriately.
DPYC-2.5
DPYC-1.5
Armor
Armor
Sheath
Sheath
TTYCS-1Q (Four core twisted)
Armor
Sheath
φ = 12.5 mm
Conductor
S = 2.5 mm 2
φ = 2.01 mm
φ = 11.7 mm
Conductor
S = 1.5 mm 2
φ = 1.56 mm
For printer, use the cable supplied with the printer.
4-6
Shield
φ = 11.3 mm
Conductor
S = 0.75 mm2
φ = 1.11 mm
4. INSTALLATION
Fabricate these cables as below to connect to the receiver unit.
DPYC-1.5 (For external alarm)
Vinyl sheath
5 mm
100 mm
25 mm
Soldering
Vinyl wire
Scrape the paint off the cable
where the cable contacts the cable clamp.
TTYCS-1Q (For Navigator or INS)
Shield
5 mm
100 mm
25 mm
Soldering
Vinyl sheath
Vinyl wire
Scrape the paint off the cable
where the cable contacts the cable clamp.
DPYC-2.5 (For ship’s battery)
5 mm
100 mm
25 mm
Crimp-on lug
(M4, local supply)
Vinyl sheath
Scrape the paint off the cable
where the cable contacts the cable clamp.
How to use J402 and 403 connector
1. Insert the terminal opener (attached in the receiver unit) into the connector.
2. Insert a wire in terminal while pressing and holding the terminal opener.
3. Release the terminal opener. Pull wire to confirm that it is connected firmly.
Terminal opener
Wire
4-7
4. INSTALLATION
Antenna cable
Be sure to leave some slack in the cable for future service and maintenance.
For RG-10/UY, RG-214 cable
When using the coaxial cable, type RG-10/UY or RG-214, attach the FM-MP-7
connector (supplied as installation material) or PL-259 (local supply) as below.
1.
2.
3.
4.
5.
Remove the sheath by 30 mm.
Bare 23 mm of the center conductor. Trim braided shield by 5 mm and tin.
Slide coupling ring onto cable.
Screw the plug assembly on the cable.
Solder plug assembly to braided shield through solder holes. Solder contact
sleeve to conductor.
6. Screw coupling ring into plug assembly.
30 mm
Sheath
5 mm
Plug assembly
Contact sleeve
2 mm
Solder here.
Conductor
Braided shield
Insulator
Coupling ring
Solder both
sides of hole.
Cut conductor here.
Note: When the RG-214 cable is used, care must be exercised to prevent
damage to the cable as it has no armor.
4-8
4. INSTALLATION
Extending antenna cable length
When connecting two cables for extension, use optional extension cable kit
OP-04-2.
Code No.: 000-041-174 (10 m), 000-041-175 (20 m), 000-041-176 (30 m),
000-041-177 (40 m), 000-041-178 (50 m)
Name
Cable assy
Connector
Insulating tape
Type
Code No.
Qty
005-948-320
005-948-330
04S4168
1
005-948-340
005-948-350
005-948-360
FMA-1
000-152-964-10
1
U tape 0.5x19x5M 000-800-985
1
Remarks
10 m w/connectors
20 m w/connectors
30 m w/connectors
40 m w/connectors
50 m w/connectors
OP04-2
To Receiver unit
FMA-1 connector
Grounding
The ground wire (local supply) should be 1.25 sq or larger. The ground wire
should be as short as possible.
4-9
4. INSTALLATION
4.6
Setting of Printer
After the connection completely, the setting of printer should be done for
NX-700B as shown below. (For NX-700A, use the default setting as is.)
1. Press the
key to turn the power on.
2. Press the MENU key to show the main menu.
Menu
NAVTEX
System
Display
Service
3. Press ▼ to choose System, and then press the ENT key or ► to activate the
System menu.
System
Warn Msg Alm
Signal Monitor
Key Beep
Time Offset
Units
Printer
Off
Off
Off
+00:00
nm, kt
NX-700A
4. Press ▼ to choose Printer, and then press the ENT key or ► to show the
item window.
None
NX-700A
Upright
Inverted
5. Press ▲ or ▼ to choose the appropriate setting, and then press the ENT
key.
None: When no printer is connected.
NX-700A: For NX-700A only.
Upright: When NX-700B is connected to an upright-type printer which ejects
paper in bottom to top direction.
Inverted: When NX-700B is connected to a bulkhead mount printer which ejects
paper in top to bottom direction.
6. Press the MENU key several times to close the menu.
4-10
4. INSTALLATION
4.7
Digital Interfacing
This equipment can receive navigation data in IEC 61162-1 Ed2/2 format.
Priority
TIME&DATE
L/L
SOG
STW
COG
ZDA
GNS > GGA > RMC > GLL
VTG > VBW > RMC
VHW > VBW
VTG > RMC
Input data sentence description
GGA: GPS position fixing condition
$--GGA,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,x,xx,x.x,x.x,M,x.x,M,x.x,xxxx*hh<CR><LF>
|
| |
|
| | | | | | | | |
| |
|
| |
|
| | | | | | | | |
| +-- 11
|
| |
|
| | | | | | | | | +---- 10
|
| |
|
| | | | | | | | +--------- 9
|
| |
|
| | | | | | +---+------------ 8
|
| |
|
| | | | +---+------------------ 7
|
| |
|
| | | +------------------------- 6
|
| |
|
| | +---------------------------- 5
|
| |
|
| +------------------------------- 4
|
| |
+----+--------------------------------- 3
|
+---+--------------------------------------------- 2
+------------------------------------------------------------- 1
1. UTC of position
2. Latitude, N/S
3. Longitude, E/W
4. GPS quality indicator (see note)
5. Number of satellite in use,00-12, may be different from the number in view
6. Horizontal dilution of precision
7. Antenna altitude above/below mean sealevel, m
8. Geoidal separation, m
9. Age of differential GPS data
10. Differential reference station ID, 0000-1023
11. Checksum
NOTE
0 = fix not available or invalid
1 = GPS SPS mode, fix valid
2 = differential GPS, SPS mode, fix valid
3 = GPS PPS mode, fix valid
4 = Real Time Kinetic. Satellite system used in RTK mode with fixed integers
5 = Float RTK. Satellite system used in RTK mode with floating fingers
6 = Estimated (dead reckoning) mode
7 = Manual input mode
8 = Simulator mode
The GPS quality indicator shall not be a null field.
4-11
4. INSTALLATION
GLL: Latitude and longitude
$--GLL,llll.lll,a,yyyyy.yyy,a,hhmmss.ss,A,a*hh<CR><LF>
| |
|
|
|
| | |
| |
|
|
|
| | +------- 6
| |
|
|
|
| +--------- 5
| |
|
|
|
+----------- 4
| |
|
|
+---------------- 3
| |
+------+----------------------- 2
+---+----------------------------------- 1
1. Latitude, N/S
2. Longitude, E/W
3. UTC of position
4. Status: A=data valid, V=data invalid
5. Mode indicator (see note)
6. Checksum
NOTE Positioning system Mode indicator:
A = Autonomous
D = Differential
E = Estimated (dead reckoning)
M = Manual input
S = Simulator
N = Data not valid
The Mode indicator field supplements the Status field. The Status field shall be
set to V=invalid for all values of Operating Mode except for A=Autonomous and
D=Differential. The positioning system Mode indicator and Status field shall not
be null fields.
4-12
4. INSTALLATION
RMC: Recommend Minimum Specific GNSS Data
$--RMC,hhmmss.ss,A,llll.lll,a,yyyyy.yyy,a,x.x,x.x,xxxxxx,x.x,a,a*hh<CR><LF>
|
| | |
|
| | |
|
| | | |
|
| | |
|
| | |
|
| | | +--- 10
|
| | |
|
| | |
|
| | +----- 9
|
| | |
|
| | |
|
+--+------- 8
|
| | |
|
| | |
+--------------- 7
|
| | |
|
| | +--------------------- 6
|
| | |
|
| +------------------------- 5
|
| | |
+---+---------------------------- 4
|
| +---+---------------------------------------- 3
|
+--------------------------------------------------- 2
+---------------------------------------------------------- 1
1. UTC of position fix
2. Status: A=data valid, V=navigation receiver warning
3. Latitude, N/S
4. Longitude, E/W
5. Speed over ground, knots
6. Course over ground, degrees true
7. Date: dd/mm/yy
8. Magnetic variation, degrees E/W
9. Mode indicator (see note)
10. Checksum
NOTE Positioning system Mode indicator:
A = Autonomous
D = Differential
E = Estimated (dead reckoning)
M = Manual input
S = Simulator
N = Data not valid
The Mode indicator field supplements the Status field. The Status field
shall be set to V=invalid for all values of Operating Mode except for
A=Autonomous and D=Differential. The positioning system Mode indicator
and Status field shall not be null fields.
4-13
4. INSTALLATION
ZDA: Time and date
$--ZDA,hhmmss.ss,xx,xx,xxxx,xx,xx*hh<CR><LF>
|
| |
| | | |
|
| |
| | | +--------- 7
|
| |
| | +----------- 6
|
| |
| +-------------- 5
|
| | +------------------ 4
|
| +---------------------- 3
|
+------------------------- 2
+--------------------------------- 1
1. UTC
2. Day, 01 to 31(UTC)
3. Month, 01 to 12(UTC)
4. Year(UTC)
5. Local zone hours, 00h to +-13h
6. Local zone minutes, 00 to +59
as local hours
7. Checksum
4-14
4. INSTALLATION
NRQ: Request NAVTEX messages
Command to request specific NAVTEX message(s) to be sent to IBS port. Messages may be
sent in any order. Each message sent from the IBS port shall be preceded by the NRX sentence.
$-NRQ,x,h,h*hh<CR><LF>
Note 1: the transmitter coverage area mask is defined as a 32 bit mask 0xFF.FF.FF.FF where
the least significant bit represents transmitter coverage area ’A’, the next bit is ’B’ and so on up
to bit 25 which is ’Z’. Bits 31-26 shall be set to ’0’. To select a transmitter coverage area its
corresponding bit shall be set to ’1’; to deselect a transmitter coverage area its corresponding
bit shall be set to ’0’.
Note 2: the message type mask is defined as a 32 bit mask 0xFF.FF.FF.FF where the least
significant bit represents message type ’A’, the next bit is ’B’ and so on up to bit 25 which is ’Z’.
Bits 31-26 shall be set to ’0’. To select a message type its corresponding bit shall be set to ’1’;
to deselect a message type its corresponding bit shall be set to ’0’.
NMK: Set NAVTEX mask
Command to set B1.B2 mask for specific NAVTEX message(s) to be stored in internal message
memory & echoed to the IBS port.
$-NMK,x,h,h*hh<CR><LF>
Note 1: the transmitter coverage area mask is defined as a 32 bit mask 0xFF.FF.FF.FF where
the least significant bit represents transmitter coverage area ’A’, the next bit is ’B’ and so on up
to bit 25 which is ’Z’. Bits 31-26 shall be set to ’0’. To select a transmitter coverage area its
corresponding bit shall be set to ’1’; to deselect a transmitter coverage area its corresponding
bit shall be set to ’0’.
Note 2: the message type mask is defined as a 32 bit mask 0xFF.FF.FF.FF where the least
significant bit represents message type ’A’, the next bit is ’B’ and so on up to bit 25 which is ’Z’.
Bits 31-26 shall be set to ’0’. To select a message type its corresponding bit shall be set to ’1’;
to deselect a message type its corresponding bit shall be set to ’0’.
Example usage:
&NVNMK,518,00001E1F,00000023*42
4-15
4. INSTALLATION
ACK: Acknowledge
$--ACK,xxx*hh<CR><LF>
| |
| + ------------------------2
+-----------------------------1
1. Local alarm number(identifier)
2. Checksum
GNS:
$--GNS,hhmmss.ss,llll.lll,a,yyyyy.yyy,a,c--c,xx,x.x,x.x,x.x,x.x,x.x*hh<CR><LF>
|
| | | | | | | | | | | |
|
| | | | | | | | | | | +--- 11
|
| | | | | | | | | | +------ 10
|
| | | | | | | | | +---------- 9
|
| | | | | | | | +-------------- 8
|
| | | | | | | +------------------ 7
|
| | | | | | +---------------------- 6
|
| | | | | +------------------------- 5
|
| | | | +------------------------------ 4
|
| | +-----+--------------------------------- 3
|
+-----+--------------------------------------------- 2
+------------------------------------------------------------- 1
1. UTC of position
2. Latitude, N/S
3. Longitude, E/W
4. Mode indicator
5. Total number of satllite in use,00-99
6. HDOP
7. Antenna altitude, metres, re:mean-sea-level (geoid)
8. Geoidal separation
9. Age of differential data
10. Differential reference station ID
11. Checksum
4-16
4. INSTALLATION
VHW: Water speed and heading
$--VHW,x.x,T,x.x,M,x.x,N,x.x,K*hh<CR><LF>
| | | | | | | | |
| | | | | | | | +--------- 5
| | | | | | +--+----------- 4
| | | | +--+----------------- 3
| | +---+----------------------- 2
+---+----------------------------- 1
1. Heading, degrees true
2. Heading, degrees magnetic
3. Speed, knots
4. Speed, km/h
5. Checksum
VTG: Course over ground and ground speed
$--VTG,x.x,T,x.x,M,x.x,N,x.x,K,a*hh<CR><LF>
| | | | | | | | | |
| | | | | | | | | +------- 6
| | | | | | | | +--------- 5
| | | | | | +--+----------- 4
| | | | +--+----------------- 3
| | +--+----------------------- 2
+--+----------------------------- 1
1. Course over ground, degrees true
2. Course over ground, degrees magnetic
3. Speed over ground, knots
4. Speed over ground, km/h
5. Mode indicator (see note)
6. Checksum
NOTE Positioning system Mode indicator:
A = Autonomous
D = Differential
E = Estimated (dead reckoning)
M = Manual input
S = Simulator
N = Data not valid
The positioning system Mode indicator field shall not be a null field.
4-17
4. INSTALLATION
VBW: Dual ground/water speed
$--VBW,x.x,x.x,A,x.x,x.x,A,x.x,A,x.x,A*hh<CR><LF>
| | | | | | | | | | |
| | | | | | | | | | +--- 11
| | | | | | | | | +----- 10
| | | | | | | | +-------- 9
| | | | | | | +----------- 8
| | | | | | +-------------- 7
| | | | | +----------------- 6
| | | | +-------------------- 5
| | | +------------------------ 4
| | +--------------------------- 3
| +------------------------------ 2
+---------------------------------- 1
1. Longitudial water speed, knots
2. Transverse water speed, knots
3. Status: water speed, A=data valid V=data invalid
4. Longitudial ground speed, knots
5. Transverse ground speed, knots
6. Status: ground speed, A=data valid V=data invalid
7. Stern transverse water speed, knots
8. Status: stern water speed, A=data valid V=data invalid
9. Stern transverse ground speed, knots
10. Status: stern ground speed, A=data valid V=data invalid
11. Checksum
4-18
4. INSTALLATION
Output data description
NRX: New NAVTEX received message
New NAVTEX message to follow in ASCII format
$NXNRX,xxxx,x,x,x,xx,xx,xxxx,hhmmss,x.x,n--n*hh<CR><LF>
encapsulated message
error rate % (xx.x)
UTC of receipt of message
year
month (1-12)
day (0-31)
freq ('490', '518' or '4209')
number of lines in message (1 to 999)
line number (1 to 999)
message identifier (B1B2B3B4)
The first NRX sentence transmitted for a particular NAVTEX message shall contain valid data
for all fields. For subsequent NRX sentences encapsulating a NAVTEX message, all fields apart
from 'message identifier', 'line number' and 'encapsulated message' are optional. If UTC time or
date are not known then the fields are NULL.
Example usage:
$NXNRX,TA21,1,4,518,10,01,2005,102000,2.2,291600 UTC JAN =*hh
$NXNRX,TA21,2,4,,,,,,,OOSTENDERADIO - INFO 37/04 =*hh
$NXNRX,TA21,3,4,,,,,,,WESTHINDER ANCHORAGE, ANCHOR LOST IN*hh
$NXNRX,TA21,4,4,,,,,,,POSITION 51-24.94N 002-40.02E.+*hh
Example usage when no UTC is available to the equipment:
$NXNRX,TA21,1,4,518,,,,,2.2, TEST MESSAGE*hh
Where the NAVTEX message contains reserved characters as defined in IEC 61162-1, then
these shall be handled by using ASCII 'escape code' :
c) Reserved character
d) <CR>
e) <LF>
f) $
^24
g) *
^2A
h) ,
^2C
i) !
^21
j) \
^5C
k) ^
^5E
l) ~
^7E
ASCII escape code
^0D
^0A
4-19
4. INSTALLATION
ALR: Set alarms
$NXALR,hhmmss.ss,xxx,A,A,c--c*hh<CR><LF>
|
| | | | |
|
| | | | +----------------- 6
|
| | | +----------------- 5
|
| | +-------------------- 4
|
| +---------------------- 3
|
+------------------------- 2
+--------------------------------- 1
1. Time of alarm condition change, UTC
2. Local alarm number(identifier)
3. Alarm condition(A=threshold exceeded, V=not exceeded)
4. Alarm's acknowledge state, A=acknowledged V=unacknowledged
5. Alarm's description text
6. Checksum
Serial Interface
4-20
MENU TREE
MENU/ESC Key
NAVTEX
System
LIST key
PRINT key
Receive Mode (INS, Auto, Manual)
Local Channel (490kHz, 4209.5kHz)
Auto Print (Off, All, User Select)
Rcv Station & Msg
User Select Station & Msg
Warn Msg Alm (Off, On)
Signal Monitor (Off, Int’l, Local)
Key Beep (Off, On)
Time Offset (-13:30 to +13:30, 0:00)
Units (nm, kt, km, km/h, mi, mi/h)
Printer (None*, NX-700A, Upright, Inverted)
*: Default seting for NX-700B.
Display
Scrolling (Slow, Fast, Skip To $$)
Font Size (Small, Medium, Large)
Time Display (24hour, 12hour)
Date Display (MMM DD YYYY, DD MMM YYYY, YYYY MMM DD)
User Display (Off, Nav Data, Distance)
Speed Display (SOG, STW)
Contrast (0 to 9, 5)
Service
INS Input Speed (4800, 9600, 19200, 38400bps)
INS Output Speed (4800, 9600, 19200, 38400bps)
Print Header (Off, On)
Edit Station List
Default Setting
Test
Rcv Monitor
All Messages
Alarm Messages
User Selected Messages
Good Messages
Lock Message
Print
Cancel Print
AP-1
FURUNO
NX-700A/B
SPECIFICATIONS OF NAVTEX RECEIVER
NX-700A/B
1
NAVTEX RECEIVER
1.1
Receiving frequency
518 kHz and 490 kHz (or 4209.5 kHz), receive both frequencies
simultaneously
1.2
Mode of reception
F1B
1.3
Sensitivity
2 µV e.m.f. (50 ohms), 4% error rate or less
1.4
Input protection
Withstands 30 Vrms for 15 minutes or more (w/ pre-amp unit)
1.5
Spurious emission
1nW or less
1.6
Message category
A: Navigation warning
B: Meteorological warning
C: Ice report
D: Search and rescue information/ pirate attack warnings
E: Meteorological forecast
F: Pilot message
G: AIS
H: Loran message
I: Spare
J: SATNAV messages
K: Other electronic navigational aid and system message
L: Navigational warning (addition to “A”)
V to Y: Special services allocation by the NAVTEX Co-ordinating
Panel
Z: QRU (no message on hand)
2
DISPLAY UNIT
2.1
Display system
5-inch, 76 (W) x 100 (H) mm, monochrome LCD, 240 x 320 dots
2.2
Display modes
Message selection mode
Message display mode
2.3
Message storage
200 messages x 2 channels
(100,000 characters x 2 channels)
3
PRINTER SECTION (FOR NX-700A ONLY)
3.1
Printing system
Line thermal head printing system
3.2
Printing paper
Thermal paper (58 mm x 30 m)
3.3
Printing width
48 mm
3.4
Character format
24 x 12 dot
3.5
Dot pitch
8 dots/ mm
3.6
Number of characters
32 characters/line
3.7
Print speed
Approx. 20 mm/sec.
SP - 1
E5649S01B-M
FURUNO
NX-700A/B
4
ANTENNA UNIT
4.1
Antenna type
NX-7H: H-field antenna
4.2
Output impedance
50 ohms
4.3
Power supply
+7 V to +9 V (thru co-ax cable)
5
INTERFACE
5.1
Input data
IEC61162-1, -2
GGA, GLL, RMC, ZDA, NRQ, NMK, ACK, GNS, VHW, VTG, VBW
5.2
Output data
NRX, ALR
Alarm
PHOTO MOS Contact closure signal (max. 0.5 A, 50 V) for SAR
alert
6
POWER SUPPLY
6.1
NX-700A
12-24VDC:
1.5-0.8A
6.2
NX-700B
12-24VDC:
0.7-0.4A
7
ENVIRONMENTAL CONDITION
7.1
Ambient temperature
Antenna unit
-25°C to +70°C
Receiver / Display unit
-15°C to +55°C
7.2
Relative humidity
95% at 40°C (without dew condensation)
7.3
Waterproofing
7.4
Antenna unit
IP66
Receiver / Display unit
IP20 (NX-700B: IP25 for front panel)
Vibration
- 2Hz to 5 Hz and up to 13.2 Hz with a deviation of ±1 mm ±10%
(7 m/s2 maximum acceleration at 13.2 Hz);
- above 13.2 Hz and up to 100 Hz with a constant maximum
acceleration of 7 m/s2 .
8
COATING COLOR
8.1
Display unit
N3.0
8.2
Receiver unit
N3.0
8.3
Antenna unit
N9.5
SP - 2
E5649S01C-M
A-1
PACKING LIST
08AW-X-9862 -2
1/1
NX-700A/NX-700A-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-700-A*
指示部
1
DISPLAY UNIT
000-040-342 **
付属品
ACCESSORIES
FP08-00800
TP058-30CL
感熱記録紙
1
RECORDING PAPER
000-154-047
工事材料
INSTALLATION MATERIALS
CP08-01861
工事材料
1
INSTALLATION MATERIALS
004-514-350
1.コ-ド番号末尾の[**]は、選択品の代表コードを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
08AW-X-9862
A-2
PACKING LIST
08AW-X-9860 -0
1/1
NX-700B/NX-700B-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-700B*
指示部
1
DISPLAY UNIT
000-152-663 **
工事材料
INSTALLATION MATERIALS
5X20 SUS304
+トラスタッピンネジ 1種
4
SELF-TAPPING SCREW
000-802-081
1.コ-ド番号末尾の[**]は、選択品の代表コードを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
08AW-X-9860
A-3
PACKING LIST
08AW-X-9861 -0
1/1
NX-7001-AN-J*/E*,NX-7001-BN-J*/E*
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-7001-*
受信部
1
RECEIVER UNIT
000-040-345 **
受信部予備品
RECEIVER UNIT SPARE PARTS
SP08-02101
予備品
1
SPARE PARTS
004-514-370
工事材料
INSTALLATION MATERIALS
CP08-01860
DSUB25P-DSUB25P-3M
ケーブル組品
1
CABLE ASSY.
000-152-698
受信部工材
RECEIVER UNIT INSTALLATION MATERIALS
CP08-01863
工事材料
1
INSTALLATION MATERIALS
004-514-530
図書
DOCUMENT
OS*-56490-*
操作要領書(和)
1
OPERATOR'S GUIDE
000-152-805 **
OM*-56490-*
取扱説明書(和)
1
OPERATOR'S MANUAL
000-152-803 **
1.コ-ド番号末尾の[**]は、選択品の代表コードを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
08AW-X-9861
A-4
PACKING LIST
08AW-X-9859 -0
1/1
NX-7001-AA-J*/E*、NX-7001-BA-J*/E*
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-7001-*
受信部
1
RECEIVER UNIT
000-040-345 **
受信部予備品
RECEIVER UNIT SPARE PARTS
SP08-02101
予備品
1
SPARE PARTS
004-514-370
工事材料
INSTALLATION MATERIALS
CP08-01860
DSUB25P-DSUB25P-3M
ケーブル組品
1
CABLE ASSY.
000-152-698
受信部工材
RECEIVER UNIT INSTALLATION MATERIALS
CP08-01864
工事材料
1
INSTALLATION MATERIALS
004-514-540
図書
DOCUMENT
OS*-56490-*
操作要領書(和)
1
OPERATOR'S GUIDE
000-152-805 **
OM*-56490-*
取扱説明書(和)
1
OPERATOR'S MANUAL
000-152-803 **
1.コ-ド番号末尾の[**]は、選択品の代表コードを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
08AW-X-9859
A-5
PACKING LIST
08AW-X-9852 -0
1/1
NX-7H-0-10/-10-HK,NX-7H-0-20/-20-HK
N A M E
ユニット
O U T L I N E
DESCRIPTION/CODE №
Q'TY
UNIT
NX-7H*
アンテナ
1
ANTENNA
000-040-214 **
工事材料
INSTALLATION MATERIALS
CP08-01810/01820
CP08-01811
工事材料
1
INSTALLATION MATERIALS
004-514-610
04S4168 *20M*
ケーブル組品
1
CABLE ASSY.
(*)
000-107-019
04S4168 *10M*
ケーブル組品
1
CABLE ASSY.
(*)
000-106-821
1.コ-ド番号末尾の[**]は、選択品の代表コードを表します。
CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.
2.(*)印のケ-ブル組品は選択出来ます。
(*) MARKED CABLES ARE SELECTABLE.
(略図の寸法は、参考値です。
DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
08AW-X-9852
A-6
CODE NO.
004-514-350
TYPE
CP08-01861
08AW-X-9401 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
+トラスタッピンネジ 1種
1
略 図
OUTLINE
型名/規格
DESCRIPTIONS
数量
Q'TY
用途/備考
REMARKS
5X20 SUS304
4
SELF-TAPPING SCREW
CODE NO.
000-802-081
08AW-X-9401
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-7
CODE NO.
004-514-530
TYPE
CP08-01863
08AW-X-9402 -0
1/1
工事材料表
INSTALLATION MATERIALS
名 称
NAME
番 号
NO.
+トラスタッピンネジ 1種
1
略 図
OUTLINE
型名/規格
DESCRIPTIONS
4
CODE NO.
2
MP-M5A
2
CODE NO.
3
000-108-861
MP-M3A
2
REDUCER(S)
CODE NO.
同軸プラグ
4
000-802-081
REDUCER(L)
アダプタ
用途/備考
REMARKS
5X20 SUS304
SELF-TAPPING SCREW
アダプタ
数量
Q'TY
000-108-860
FM-MP-7
2
COAX.PLUG
CODE NO.
000-108-859
08AW-X-9402
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-8
CODE NO.
004-514-540
TYPE
CP08-01864
08AW-X-9403 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
+トラスタッピンネジ 1種
1
略 図
OUTLINE
型名/規格
DESCRIPTIONS
4
CODE NO.
2
用途/備考
REMARKS
5X20 SUS304
SELF-TAPPING SCREW
同軸プラグ
数量
Q'TY
000-802-081
FM-MP-7
1
COAX.PLUG
CODE NO.
000-108-859
08AW-X-9403
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-9
08AW-X-9407 -0
CODE NO.
1/1
TYPE
工事材料表
NX-700A/B
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
ケーブル組品
1
略 図
OUTLINE
型名/規格
DESCRIPTIONS
1
CODE NO.
2
選択 TO BE SELECT
04S4168 *40M*
1
CODE NO.
3
000-107-020
CABLE ASSY.
ケーブル組品
用途/備考
REMARKS
選択 TO BE SELECT
04S4168 *30M*
CABLE ASSY.
ケーブル組品
数量
Q'TY
000-107-021
選択 TO BE SELECT
04S4168 *50M*
1
CABLE ASSY.
CODE NO.
000-107-022
08AW-X-9407
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-10
CODE NO.
004-514-610
TYPE
CP08-01811
08AW-X-9404 -0
1/1
工事材料表
INSTALLATION MATERIALS
番 号
NO.
名 称
NAME
型名/規格
DESCRIPTIONS
数量
Q'TY
用途/備考
REMARKS
Uテープ 0.5X19X5M
絶縁テープ
1
略 図
OUTLINE
1
SELF-BONDING TAPE
CODE NO.
000-800-985
08AW-X-9404
FURUNO ELECTRIC CO .,LTD.
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
A-11
NAME OF
PART
OUTLINE
ヒューズ
1
004-514-370
TYPE
SP08-02101
SPARE PARTS LIST FOR
SHIP NO.
ITEM
NO.
CODE NO.
U
DWG. NO.
OR
TYPE NO.
S
08AW-X-9301 -0 1/1
BOX NO.
P
SETS PER
VESSEL
E
QUANTITY
REMARKS/CODE NO.
WORKING
PER
SET
PER
VES
SPARE
FGMB 2A 125V
1
FUSE
000-103-165
MFR'S NAME
FURUNO
ELECTRIC
CO.,LTD.
DWG NO.
08AW-X-9301
(略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.)
1/1
D-1
Y. Hatai
D-2
D-3
D-4
Y. Hatai
D-5
D
固定ボルト
FIXING BOLT
アンテナケーブル
ANTENNA CABLE
0°
-5°
33°
-5° - 33°
ANTENNA BASE No.13-QA330
TYPE
コード番号 000-803-239
CODE No.
アンテナ
直型アンテナベース
ベース型式 RIGHT ANGLE ANTENNA BASE
MOUNTING
METHOD
装備方法
INCLINATION
傾斜
000-803-240
No.13-QA310
L-TYPE ANTENNA BASE
L型アンテナベース
0°
32°
65°
32° -
65°
0°
65° 98°
65° -
98°
C)取付ける場所が傾斜しているとき ANTENNA BASE MOUNTING
オプションのアンテナベースを使う。
USE OPTIONAL ANTENNA BASE No.13-QA330/QA310.
CABLE TIE
(LOCAL SUPPLY)
テープを巻く
WIND TAPE
KEEP CABLE ASIDE TO AVOID
INJURY FROM PIPE.
90゚
MOUNTING LOCATION
4
a
*
3 m
1.5 m
3 m
10 cm
30 cm
φ 76
φ61
4-M5 皿穴
COUNTERSUNK
表 1
1 m
DWG. No.
SCALE
APPROVED
CHECKED
1.5 m
THREAD PER 25.4mm (1 INCH): 14
PITCH: 1.8143 mm
THREAD LENGTH: 15.17 mm
PITCH DIAMETER: 24.17 mm
1-14UNS1B
ねじ山数(25.4mmにつき): 14
ピッチ: 1.8143 mm
オネジ有効長さ: 15.17 mm
オネジ有効径: 24.17 mm
TX ANTENNA(MF/HF)
送信アンテナ(MF/HF)
MAIN MAST
メインマスト
4 m
4 m
NX-700
NX-300
08-021-310G- 1
±10% MASS W/ 10m CABLE.
0.94 kg 質量は10mケーブルを含む。
C5629-G05- E
1/2
MASS
TAKAHASHI.T
E.MIYOSHI
1. TABLE 1 INDICATES TOLERANCE OF DIMENSIONS.
DRAWN
MAY 16, '05
NOTE
0.5 m
NAVTEX ANTENNA
ナブテックスアンテナ
1 m
1)指定なき寸法公差は表1による。
±3
注記
±2.5
50 < L ≦ 100
公差(mm)
TOLERANCE
±1.5
TABLE 1
WHIP ANTENNA
ホイップアンテナ(MF/HF)
WHIP ANTENNA
ホイップアンテナ(VHF/UHF)
RX WHIP ANTENNA
受信ホイップアンテナ
100 < L ≦ 500
寸法区分(mm)
DIMENSIONS
0 < L ≦ 50
DISTANCE (MIN.)
確保する距離
DIA. OF 'a'
aの直径
*支柱の太さにより変わる。
* DISTANCE DEPENDS ON MAST DIAMETER OF 'a'.
レーダービームに入らないこと
NOT WITHIN RADAR BEAM
5 m NOT WITHIN INMARSAT BEAM
インマルビームに入らないこと
INMARSAT ANTENNA
インマルサットアンテナ
LOOP ANTENNA
ループ・アンテナ
5
THE FIGURE BELOW SHOWS THE RECOMMENDED SEPARATION DISTANCES
FROM OTHER ANTENNAS TO AVOID MUTUAL INTERFERENCE.
他の機器のアンテナから下の図の距離以上離す。
取付場所
MOUNTING DIMENSIONS OF ANTENNA BASE
アンテナベース基部
注記 1)パイプ(アンテナベース)はアンテナユニットにねじ込んだ後に固定する。
2)アンテナを固定するときはパイプ(アンテナベース)をアンテナにねじ込むこと。
アンテナ側をねじるとコネクタ部やケーブルに無理がかかり、故障の原因となる。
NOTE 1. FASTEN PIPE(ANTENNA BASE) TO ANTENNA UNIT FIRST THEN FIX THEM TO MAST OR HANDRAIL.
2. WHEN FIXING ANTENNA, TURN PIPE OR ANTENNA BASE; NOT THE ANTENNA.
TURNING THE ANTENNA MAY TWIST THE CABLE AND PLACE STRESS ON CONNECTOR.
アンテナベース
ANTENNA BASE
USE HANDRAIL MOUNTING BASE No.13-RC5160
(CODE No.000-806-114, OPTION).
THE DIAMETER OF THE HANDRAIL MAY BE FROM
φ19mm TO φ32mm.
PIPE
WIND TAPE
テープを巻く
3
コンベックス
(現地手配)
パイプで傷つかないよう
ケーブルを脇へよける。
パイプ
HANDRAIL MOUNTING
コンベックス
(現地手配)
CABLE TIE
(LOCAL SUPPLY)
パーカー
クランプ
HOSE CLAMP
ケーブル固定板
CABLE FIXTURE
USE A PIPE ONLY.
b)パイプのみを使うとき
レール用アンテナベース No.13-RC5160(取付可能レール直径:φ19∼φ32)
(コード番号:000-806-114)
B)スタンションやパルピットにつけるとき
LEAVE SLACK HERE TO RELIEF
STRESS ON CONNECTOR.
115
C
ANTENNA CABLE
120
アンテナケーブル
MOUNTING BRACKET
取付補助金具
コネクタに力がかからない
よう、余裕を持たせる。
PIPE
パイプ
WIND TAPE
テープを巻く
USE MAST MOUNTING KIT CP20-01111.
173
B
2
a)マスト取付金具CP20-01111(工事材料)でマストに固定する。
MAST MOUNTING
173
A
1
A)マストへの取付け
NAME
名称
TITLE
ケーブル固定板
CABLE FIXTURE
ANTENNA UNIT
OUTLINE DRAWING
外寸図
NX-3H-D/NX-7H
空中線部
φ156
6
D
C
B
A
D-6
45゚
116
C
B
A
+ DC IN
-
NOTE
*1. SHIPYARD SUPPLY.
*2. OPTION.
*3. SELECT OUTPUT OF PRINTER SIGNAL FROM MENU.
DWG.No.
SCALE
J403(WAGO)
ALARM-H
ALARM-C
FG
SD *3
RD
SG
FG
FG
MASS
Y. Hatai
TAKAHASHI.T
E.MIYOSHI
B2 RCV 08P3227
1
2
3
4
5
6
7
8
1
2
3
4
5
6
J402(WAGO)
(IEC61162-2)
TD-A
TD-B
GND-ISO
RD-A
RD-B
FG
TB401
(+)
TB402
(-)
受信部
RECEIVER UNIT
NX-7001
C5649-C01- D
Jul.8,'05
APPROVED
CHECKED
DRAWN
*1
DPYC-1.5
(MAX.0.5A,50V)
*1
RS-232C CABLE
プリンタ
PRINTER
(NX-700Bのみ)
(NX-700B ONLY)
*1
外部アラーム
EXT. ALARM
*1
TTYCS-1Q
*1
TTYCS-1Q
PE,IV-1.25sq *1
保護アース
DC OUT +
-
SUPPLY UNIT
PR-240-CE *2
AC/DC電源ユニット
2
AC IN AC/DC POWER
J402(WAGO)
INS
3 GND-ISO
4 RD-A
5 RD-B
6 FG
*1
DPYC-2.5
*1
DPYC-1.5
*1
DPYC-2.5
注記
*1)造船所手配。
*2)オプション。
*3)プリンタ信号出力はメニューにて選択。
*1
TTYCS-1Q
24VDC
100-115/
200-230VAC
1φ,50/60Hz
12-24 VDC
NAVIGATOR
航法装置
1
1
14
2
15
3
16
4
17
5
18
6
19
7
20
8
21
9
22
10
23
11
24
12
25
13
ANT
FMA-1 M-P-3
NAME
名 称
TITLE
M-P-3
M-P-3
0.6m
アンテナ部
ANTENNA UNIT
NX-7H
INTERCONNECTION DIAGRAM
NAVTEX RECEIVER
相互結線図
NX-700A/B
ナブテックス受信機
GND *1
IV-1.25sq.
NX-700A/B
指示部
DISPLAY UNIT
*1
*2
MP-7 or PL-259
RG-10/UY,30/40/50m
or RG-214 *1, MAX200m
04S4168,φ5.5
10/20/30/40/50m
EXTENSION CABLE KIT
04S4168,10/20/30/40/50m,φ5.5
延長ケーブルキット*2
4
DSUB25P-DSUB25P-3M, 1 RECEIVER
SD(NX-700A)/NC(NX-700B)
3m,φ10
14 RD(NX-700A)/NC(NX-700B)
(5/10/15m, *2)
2 TD-A
15 TD-B
3 RD-A
16 RD-B
4 ALARM-H
17 ALARM-C
5 TEST-RD-A
18 TEST-RD-B
6 FRQ-RD-A
19 FRQ-RD-B
7 490-TD-A
20 490-TD-B
8 518-TD-A
21 518-TD-B
9 12V+
22 0V SG
10 0V GND-ISO
23 DC+
11 DC+
24 DC+
12 DC25 DC13 DC-
FM-MP-7
or
*1
PL-259
M-P-3
08-001-3157-A
GND *1
IV-1.25sq.
J401
SD
RD
TD-A
TD-B
RD-A
RD-B
ALARM-H
ALARM-C
TEST-RD-A
TEST-RD-B
FRQ-RD-A
FRQ-RD-B
490-TD-A
490-TD-B
518-TD-A
518-TD-B
12V+
0V SG
0V GND-ISO
DC+
DC+
DC+
DCDCDC*3
3
S-1
INDEX
Editing..................................................... 2-14
A
Alarm message ............................................. 2-9
O
C
Output Speed.............................................. 2-19
Contrast ...................................................... 2-18
P
D
Date............................................................ 2-21
Default Settings ............................................ 3-6
Diagnostics ................................................... 3-5
F
Font Size .................................................... 2-18
Frequency..................................................... 2-8
Power ........................................................... 2-1
Printer Setting ............................................. 4-10
Printing ....................................................... 2-10
all messages........................................... 2-10
canceling ................................................ 2-11
each messages....................................... 2-11
Print header ................................................ 2-19
Protecting ................................................... 2-10
R
Icons........................................................... 2-15
Input Speed ................................................ 2-19
Rcv Monitor................................................. 2-19
Receive Mode............................................... 2-5
Replacement................................................. 3-2
K
S
Keys ............................................................. 2-1
Key Beep.................................................... 2-17
Scrolling...................................................... 2-18
Speed Display............................................. 2-18
L
T
LCD dimmer ................................................. 2-2
Time Display ............................................... 2-18
Time Offset ................................................. 2-17
Troubleshooting ............................................ 3-4
I
M
Maintenance ................................................. 3-1
Menu Tree ................................................. AP-1
Message
Sample ..................................................... 2-4
Format ...................................................... 1-2
List.......................................................... 2-16
New .......................................................... 2-3
Processing ................................................ 2-9
U
Units ........................................................... 2-17
N
NAVTEX ....................................................... 1-1
NAVTEX Station Map .................................... 1-3
NAVTEX Station List ..................................... 1-4
Adding .................................................... 2-12
Deleting .................................................. 2-14
IN-1