User manual | Fusion CA-DA41400 Car Amplifier User Manual

USER MANUAL
D-CLASS AMPLIFIER
CA-DA12250 CA-DA41400 CA-DA51600
Specifications and design are subject to change without notice
AMPLIFIER SPECIFICATIONS
CA-DA12250
Peak Power (Watts)
Frequency Response
Dimensions (mm)
Power Ratings
CA-DA41400
CA-DA51600
2250
1400
1600
10Hz - 250Hz
10Hz -65kHz
10Hz -50kHz
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
300(l) x 210(w) x 50(h)
11-13/16 x 8-1/4 x 2”
500W RMS x 1 @ 4Ω 1%
THD+N
150W RMS x 4 @ 4Ω 1%
THD+N
80W RMS x 4 +
250W RMS x 1 @ 4Ω 1%
THD+N
850W RMS x 1 @ 2Ω 1%
THD+N
220W RMS x 4 @ 2Ω 1%
THD+N
130W RMS x 4 +
330W RMS x 1 @ 2Ω 1%
THD+N
1100W RMS x 1 @ 1Ω 1%
THD+N
440W RMS x 2 @ 4Ω
Bridged 1% THD+N
250W RMS x 2 @ 4Ω
Bridged 1% THD+N +
250W RMS x 1 @ 4Ω 1%
THD+N
INSTALLATION GUIDELINES
1.
2.
3.
4.
Ensure the +12V lead is disconnected from
the battery before you connect any new
equipment.
Ensure the mounting location will not
interfere with the gas tank, brake lines or
electrical wiring.
Ensure the Amplifier is securely fastened to
the vehicle to prevent injury in the event of
an accident.
Ensure all wiring is protected to avoid
pinching or crushing which could result in
damage to the audio system.
POWER
FUSION amplifiers should be connected directly
to the +12V battery terminal with an inline fuse or
circuit breaker as close the battery as possible.
5.
6.
7.
WIRING
1.
Ensure the audio system is turned off before
making any connections to the amplifier,
speakers or source unit, failure to do so could
result in permanent damage to the audio
system.
2.
When wiring the FUSION amplifier ensure
that the cable is protected from sharp objects
and always use rubber grommets when wiring
through metal panels.
3.
Ensure all terminals and connections are
protected from the vehicle chassis and from
each other as failure to do so could result in
permanent damage to the audio system.
GROUND
When grounding/earthing your amplifier ensure that
the location is a good source of ground (preferably
the floor pan). Make sure the metal is clean of paint
etc as a poor earth could damage your audio system.
REMOTE TURN ON
This connection turns the amplifier on & should be
connected to the remote turn on wire from the Head
Unit. If one is not available a switched 12v source must
be used. Either a power antenna wire or ACC +12V.
Ensure the mounting location has sufficient
air flow around the amplifier. If the amplifier
is mounted in an enclosed space a 3” fan
with ducting should be used to aid in air
flow.
Do not mount any amplifier on a subwoofer
enclosure as extended exposure to vibration
may cause malfunction of the amplifier.
Ensure you use the recommended gauge
wire/cable for all amplifier connections.
LOW LEVEL INPUTS
Choose the correct length RCA cable & run them to the
RCA outputs of the source/head unit, avoiding running
beside other looms & or power cable.
For specific wiring information please
refer to www.fusionelectronics.com
LEVEL CONTROL
This control is used to match the input level of the amplifier to the output level of you head unit. We recommend
the following method. NOTE: Remove screws and the top cover of amplifier to access controls.
1.
Turn the amplifier level to zero
2.
Turn the volume of the head unit to ¾ and the
bass and treble to zero
3.
Adjust the level control until the desired
maximum volume is achieved without
distortion.
4.
Failure to follow these steps may cause
permanent damage to the audio system.
CROSSOVER TABLE
Model
CADA51600
CADA41400
CADA12250
Channels
Crossover Type
Crossover Frequency
Bass Boost
Front
Selectable - LPF, HPF, or
FULL
LPF or HPF Tunable - 32Hz
- 320Hz
Rear
Selectable - LPF, HPF, or
FULL
LPF or HPF Tunable - 32Hz
- 320Hz
Sub
Fixed LPF and Fixed HPF
(Subsonic)
LPF Tunable - 32Hz - 320Hz
HPF Tunable - 10Hz - 80Hz
Front
Selectable - LPF, HPF, or
FULL
LPF or HPF Tunable - 32Hz
- 320Hz
Rear
Selectable - LPF, HPF, or
FULL
LPF or HPF Tunable - 32Hz
- 320Hz
Tunable - 0dB 12dB
All
Fixed LPF and Fixed HPF
(Subsonic)
LPF Tunable - 32Hz - 320Hz
HPF Tunable - 10Hz - 80Hz
Tunable - 0dB 12dB
Tunable - 0dB12dB
TROUBLE SHOOTING
Problem
Possible Reason
Solution
Amplifier not switching
on. Power LED not ‘on’.
No +12v to power wire
No power to remote wire
Fuse broken
Fuse on amplifier blown
Check fuses and connections to battery
Check remote on connections to head unit
Replace fuse with correct type and amperage
Replace fuse with correct type and amperage
Amplifier not working,
but Power LED is ‘on’
Amplifier too hot
Speaker wires shorted
Move amplifier to vented area
Turn head unit down
Check that there are no speaker wires shorted to
another wire or to the vehicle chassis
No Sound
No RCA Signal
Gain control not set up
Head Unit off or low vol
Amplifier
Speakers
Check RCA connection to head unit
Ensure you have set up the amplifier gain level control
Check head unit volume level
Check all power, remote on and ground connections
Check speakers for wire shorts
AMPLIFIER DIMENSIONS
All dimensions provided are in millimeters (mm) unless indicated
1/4
6.5
50 1-31/32"
12 15/32"
160 6-5/16"
210 8-9/32"
300 11-13/16"
268 10-9/16"
"
CA-DA12250, CA-DA41400, CA-DA51600
CA-DA12250 - CONTROL DESCRIPTIONS
1
2
10
3
4
11
1. SPEAKER OUTPUT:
Connect your subwoofer(s) to these terminals.
NOTE: The positive (+) and negative (-) are internally linked.
2. REMOTE LEVEL CONTROL CONNECTION:
Connect the optional (supplied) Remote Level Controller to
this socket.
3. RCA INPUT:
Connect these RCA connectors to a head unit with a low level
output connection.
4. RCA OUTPUT:
Use these RCA connectors to connect to a secondary
amplifier. This output is a pass-thru connection derived
from the RCA input connectors so that the signal level and
frequency response is the same as the original input signal.
5. POWER AND STATUS LED’S:
This displays “green” if the amplifier has been correctly
powered up & ‘red’ if any faults are present.
6. FUSES:
Please ensure the correct type of fuse is fitted. For CADA12250 3 x 40A fuses.
7. +12V CONNECTION:
Connect directly to the vehicle battery positive (+) terminal via
a 4 gauge power cable, with an inline fuse or circuit breaker
at the battery end. NOTE: This is the last wire to connect up
during installation. Damage could result if this is not done.
8. REMOTE TURN-ON CONNECTION:
This terminal is for turning the amplifier on and off. The
remote input requires a switched positive (+12V) to power
‘ON’ the amplifier. This can usually be found on the rear of
the head unit in the form of a remote output. If not available
you can wire to the ACC position on the ignition key.
5
6
7
8
9
12
9. GROUND CONNECTION:
Connect directly to the vehicle’s chassis via a 4 guage power
cable. NOTE: This is the first wire to connect up during the
installation.
10. LEVEL CONTROL:
This allows level adjustment of the input signal. Use this
control to directly match the head unit to the amplifier. To
set this control correctly, turn the amplifier level to MIN and
the head unit to 3/4 volume, with the bass and treble on zero,
then slowly turn up the level control towards the MAX end of
the control. NOTE: If the sound becomes distorted, turn this
control down.
11. SUBWOOFER LP FILTER FREQUENCY:
This sets the crossover frequency point for the subwoofer
channels’ low pass filter between 32Hz and 320Hz.
12. FUSION LOW FREQUENCY CONTROL:
The FUSION Low Frequency Control (F.L.F.C.) is a dual stage
control interface. The combination of a Subsonic filter and a
Bass Boost control allows precise shaping of the audio signal
for your subwoofer(s). The Subsonic filter is essentially a
high-pass crossover which blocks the frequency signal from
10Hz - 80Hz. This signal often contains no music and its
removal will improve subwoofer control. The Bass Boost is a
variable control to increase the level at 45Hz from 0 - +12dB
of gain. Adjust these controls with extreme care.
CA-DA41400 - CONTROL DESCRIPTIONS
1
2
3
10
4
5
6
7
8
9
13
14
11
15
12
1. SPEAKER OUTPUT:
Connect your speakers to these terminals.
2. RCA OUTPUT:
Use these RCA connectors to connect to a secondary
amplifier. This output is a pass-thru connection derived
from the RCA input connectors so that the signal level and
frequency response is the same as the original input signal.
3. REAR RCA INPUT:
Connect these RCA connectors to a head unit with a rear low
level output connection.
4. FRONT RCA INPUT:
Connect these RCA connectors to a head unit with a front low
level output connection.
5. POWER AND STATUS LED’S:
This displays “green” if the amplifier has been correctly
powered up & ‘red’ if any faults are present.
6. FUSES:
Please ensure the correct type of fuse is fitted.
For CA-DA41400 2 x 40A fuses.
7. +12V CONNECTION:
Connect directly to the vehicle battery positive (+) terminal via
a 4 gauge power cable, with an inline fuse or circuit breaker
at the battery end. NOTE: This is the last wire to connect up
during installation. Damage could result if this is not done.
8. REMOTE TURN-ON CONNECTION:
This terminal is for turning the amplifier on and off. The
remote input requires a switched positive (+12V) to power
‘ON’ the amplifier. This can usually be found on the rear of
the head unit in the form of a remote output. If not available
you can wire to the ACC position on the ignition key.
9. GROUND CONNECTION:
Connect directly to the vehicle’s chassis via a 4 guage power
cable. NOTE: This is the first wire to connect up during the
installation.
10. REAR LEVEL:
This allows level adjustment of the front input signal. Use this
control to directly match the head unit to the amplifier. To
set this control correctly, turn the amplifier level to MIN and
the head unit to 3/4 volume, with the bass and treble on zero,
then slowly turn up the level control towards the MAX end of
the control. NOTE: If the sound becomes distorted, turn this
control down.
16
11. BASS BOOST:
The Bass Boost is a variable control to increase the level at
45Hz from 0 - +12dB of gain. Adjust this control with extreme
care.
12. FRONT LEVEL:
This allows level adjustment of the rear input signal. Use this
control to directly match the head unit to the amplifier. To
set this control correctly, turn the amplifier level to MIN and
the head unit to 3/4 volume, with the bass and treble on zero,
then slowly turn up the level control towards the MAX end of
the control. NOTE: If the sound becomes distorted, turn this
control down.
13. REAR FILTER FREQUENCY:
This sets the crossover frequency point for the rear filter
between 32Hz and 320Hz. NOTE: Failure to correctly set
could result in speaker damage.
14. REAR FILTER SELECTION:
This switch selects the type of filter used for the rear audio
signal. Either Low Pass, High Pass or Full Range can be
selected. The Low Pass filter is designed to filter out all mid
to high frequencies that only full range speakers should
produce. The High Pass filter is designed to filter out all
low frequencies that only subwoofers should produce. Full
Range allows all frquencies.
15. FRONT FILTER SELECTION:
This switch selects the type of filter used for the rear audio
signal. Either Low Pass, High Pass or Full Range can be
selected. The Low Pass filter is designed to filter out all mid
to high frequencies that only full range speakers should
produce. The High Pass filter is designed to filter out all
low frequencies that only subwoofers should produce. Full
Range allows all frquencies.
16. FRONT FILTER FREQUENCY:
This sets the crossover frequency point for the rear filter
between 32Hz and 320Hz. NOTE: Failure to correctly set
could result in speaker damage.
CA-DA51600 - CONTROL DESCRIPTIONS
1
2
3
4
1. SPEAKER OUTPUT:
Connect your speakers to these terminals.
11
3. REAR RCA INPUT:
Connect these RCA connectors to a head unit with a rear low
level output connection.
12
5. REMOTE LEVEL CONTROL CONNECTION:
Connect the optional (supplied) Remote Level Controller to
this socket.
6. POWER AND STATUS LED’S:
This displays “green” if the amplifier has been correctly
powered up and ‘red’ if any faults are present.
7. FUSES:
Please ensure the correct type of fuse is fitted. For CADA51600 2 x 40A fuses.
8. +12V CONNECTION:
Connect directly to the vehicle battery positive (+) terminal via
a 4 gauge power cable, with an inline fuse or circuit breaker
at the battery end. NOTE: This is the last wire to connect up
during installation. Damage could result if this is not done.
9. REMOTE TURN-ON CONNECTION:
This terminal is for turning the amplifier on & off. The remote
input requires a switched positive (+12V) to power ‘ON’ the
amplifier. This can usually be found on the rear of the head
unit in the form of a remote output. If not available you can
wire to the ACC position on the ignition key.
10. GROUND CONNECTION:
Connect directly to the vehicle’s chassis via a 4 guage power
cable. NOTE: This is the first wire to connect up during the
installation.
6
7
8
9
10
14
2. FRONT RCA INPUT:
Connect these RCA connectors to a head unit with a front low
level output connection.
4. SUBWOOFER RCA INPUT:
Connect these RCA connectors to a head unit with a
subwoofer low level output connection.
5
15
16
17
18
13
19
20
Bass Boost control allows precise shaping of the audio signal
for your subwoofer(s). The Subsonic filter is essentially a
high-pass crossover which blocks the frequency signal
from 10Hz - 80Hz. This signal often contains no music & its
removal will improve subwoofer control. The Bass Boost is a
variable control to increase the level at 45Hz from 0 - +12dB
of gain. Adjust these controls with extreme care.
15. SUBWOOFER AUDIO SOURCE:
This switch selects the audio source for the subwoofer
channel. Audio can be sourced from the SUB input
RCA connectors or from the FRONT & REAR input RCA
connectors.
16. SUBWOOFER LEVEL:
This allows level adjustment of the subwoofer input signal.
Use this control to directly match the head unit to the
amplifier. To set this control correctly, turn the amplifier level
to MIN & the head unit to 3/4 volume, with the bass and treble
on zero, then slowly turn up the level control towards the MAX
end of the control. NOTE: If the sound becomes distorted,
turn this control down.
11. SUBWOOFER LP FILTER FREQUENCY:
This sets the crossover frequency point for the subwoofer
channels’ low pass filter between 32Hz and 320Hz.
17. REAR FILTER FREQUENCY:
This sets the crossover frequency point for the rear filter
between 32Hz and 320Hz. NOTE: Failure to correctly set
could result in speaker damage.
12. REAR LEVEL:
This allows level adjustment of the rear input signal. Use this
control to directly match the head unit to the amplifier. To
set this control correctly, turn the amplifier level to MIN and
the head unit to 3/4 volume, with the bass and treble on zero,
then slowly turn up the level control towards the MAX end of
the control. NOTE: If the sound becomes distorted, turn this
control down.
18. REAR FILTER SELECTION:
This switch selects the type of filter used for the rear audio
signal. Either Low Pass, High Pass or Full Range can be
selected. The Low Pass filter is designed to filter out all mid
to high frequencies that only full range speakers should
produce. The High Pass filter is designed to filter out all
low frequencies that only subwoofers should produce. Full
Range allows all frquencies.
13. FRONT LEVEL:
This allows level adjustment of the front input signal. Use this
control to directly match the head unit to the amplifier. To
set this control correctly, turn the amplifier level to MIN and
the head unit to 3/4 volume, with the bass and treble on zero,
then slowly turn up the level control towards the MAX end of
the control. NOTE: If the sound becomes distorted, turn this
control down.
19. FRONT FILTER SELECTION:
This switch selects the type of filter used for the rear audio
signal. Either Low Pass, High Pass or Full Range can be
selected. The Low Pass filter is designed to filter out all mid
to high frequencies that only full range speakers should
produce. The High Pass filter is designed to filter out all
low frequencies that only subwoofers should produce. Full
Range allows all frquencies.
14. FUSION LOW FREQUENCY CONTROL:
The FUSION Low Frequency Control (F.L.F.C.) is a dual stage
control interface. The combination of a Subsonic filter & a
20. FRONT FILTER FREQUENCY:
This sets the crossover frequency point for the rear filter
between 32Hz and 320Hz. NOTE: Failure to correctly set
could result in speaker damage.
RECORD YOUR PURCHASE DETAILS HERE:
SERIAL NUMBER
DATE OF PURCHASE
AFFIX RECEIPT HERE
www.fusionelectronics.com
FUSION Electronics New Zealand
FUSION Electronics Australia
FUSION Electronics Europe
FUSION Electronics USA
Ph: +64 9 369 2900
Ph: +61 1300 736 012
Ph: +44 845 299 7586
Ph: +1 623 580 9000
For further product and installation information, please visit www.fusionelectronics.com
Pour plus d’informations sur les produits et l’installation, rendez-vous sur www.fusionelectronics.com
Para obtener más información acerca de los productos y de su instalación, visite el sitio web www.fusionelectronics.com
Bezoek www.fusionelectronics.com voor meer product- en installatie-informatie.
Weitere Produkt- und Installationsinformationen finden Sie unter www.fusionelectronics.com
Per ulteriori informazioni sui prodotti e la loro installazione, potete visitare www.fusionelectronics.com
Для получения дополнительной информации о продуктах и установке зайдите, пожалуйста, на: www.fusionelectronics.com
WARNING: Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!
PUBLISHED BY FUSION ELECTRONICS LIMITED: © Copyright 2010 by FUSION Electronics Limited. All rights reserved. Specifications and design are subject to change without notice.
YOU CAN HELP PROTECT THE ENVIRONMENT! Please remember to respect the local regulations: Hand in the non-working electrical equipment to an appropriate waste disposal center.
Download PDF

advertising