Garmin 010-00921-02 GPS Receiver User Manual

Model 28225
DECT6.0
Cordless Handset
Speakerphone
Answering System
User’s Guide
Important Information
NOTICE: This product meets the applicable Industry Canada technical
specifications.
Operation is subject to the following two conditions: (1) This device may
not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
The equipment must be installed using an acceptable method of
connection. The customer should be aware that compliance with the
above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any repairs
or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe systems, if present, are connected together. This precaution
may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the
telephone company.
Interference Information
This equipment generates and uses radio frequency energy which may
interfere with residential radio and television reception if not properly
installed and used in accordance with instructions contained in this
manual. Reasonable protection against such interference is ensured,
although there is no guarantee this will not occur in a given installation.
If interference is suspected and verified by switching this equipment
on and off, the user is encouraged to try to correct the interference by
one or more of the following measures: Reorient the radio/television
receiver’s antenna, relocate the equipment with respect to the receiver,
plug the equipment and receiver into separate circuit outlets. The
user may also wish to consult a qualified radio/television technician
for additional suggestions. This equipment has been fully tested and
complies with all limits for Class B computing devices pursuant to part 15
FCC Rules and Regulations.
Telephone Network Information
Should your equipment cause trouble on your line which may harm the
telephone network, the telephone company, where practicable, may
notify you that temporary discontinuance of service may be required.
Where prior notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily discontinue service
immediately.
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action is
required in the operation of its business. If these changes are expected
to affect the use or performance of your telephone equipment, the
telephone company will likely give you adequate notice to allow you to
maintain uninterrupted service.
Notice must be given to the telephone company upon termination of
your telephone from your line.
REN Number
On the bottom of this equipment is a label indicating, among other
information, the Ringer Equivalence Number (REN) for the equipment.
The REN is useful in determining the number of devices you may connect
to your telephone line and still have all of these devices ring when
your telephone number is called. In most (but not all) areas, the sum
of the RENs of all devices connected to one line should not exceed 5.
To be certain of the number of devices you may connect to your line
as determined by the REN, you should contact your local telephone
company.
REN Number is located on the cabinet bottom.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid
Compatibility.
Licensing
Licensed under US Patent 6,427,009.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters between
the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.
Information for DECT Product
This telephone is compliant with the DECT 6.0 standard
which operates in the 1.92GHz to 1.93GHz frequency
range.
Table of Contents
Important Information. ...............2
Interference Information. ...........2
Telephone Network Information3
REN Number...............................3
Hearing Aid Compatibility (HAC)3
Licensing.....................................3
FCC RF Radiation Exposure
Statement.................................4
Information for DECT Product..4
Introduction...............................7
Before You Begin........................7
Parts Checklist . ..........................7
Telephone Jack Requirements......7
Installation ................................8
Digital Security System...............8
Important Installation
Guidelines..................................9
Base Layout. .............................10
Handset Layout.........................11
Display Icons.............................. 11
Installing the Phone. ................12
Installing the Handset
Batteries.................................. 12
Base Station............................... 13
Answering System Setup............14
Answering System ON/OFF.... 14
Setting the Voice Language.... 14
Recording the Outgoing
Announcement....................... 14
Remote Access Code................. 15
Announce Only On/Off.......... 15
Message Alert............................ 15
Rings to Answer........................ 16
Call Screening........................... 16
Programming Your Phone.........17
Main Menu. ................................ 17
Date & Time................................ 17
Ringer Setup. ............................. 18
Ringer Volume........................ 18
External Ringtone ................ 18
Intercom Ringtone................. 18
Group Melody. .......................... 18
Set Alarm. .................................. 19
Auto Talk.................................... 19
Registration................................ 19
Register Handset. .................. 19
Deregister Handset............... 20
Select Base................................. 20
Tones ON/OFF.......................... 20
Reset Handset............................ 21
Handset Display Settings........ 21
Wallpaper................................... 21
Handset Name............................ 21
Display Contrast....................... 21
Handset Language.................... 22
Base Setup.................................. 22
Area Code................................... 22
Dial Mode................................... 22
Answering System Setup
via the Handset...................... 23
Answering System ON/OFF.... 23
Rings to Answer........................ 23
Message Alert............................ 23
Setting the Voice Language.... 23
Remote Access Code................. 23
Answering System Operation.....24
Listening to Your Messages.... 24
Message Playback. .................... 24
Deleting Messages.................... 24
Base Ringer Volume.................. 25
Memo Recording. ...................... 25
Remote Operation...................... 26
Memory Full.............................. 26
Important Information.............. 26
Handset Operation....................27
Making a Call............................ 27
Pre-Dialing:............................. 27
Dialing:..................................... 27
Receiving a Call......................... 27
Redialing..................................... 28
Changing the Earpiece Volume28
Handset Speaker Phone........... 28
Muting the Microphone .......... 28
DND (Do Not Disturb)............ 28
Muting the Ringer during
an Incoming Call................... 28
Disabling the Ringer on the
Handset................................... 28
Paging the Handset.................. 29
Key Lock...................................... 29
Intercom Operation...................29
Making Intercom Calls............ 29
Receiving Intercom Calls......... 29
Three Party Conference.......... 30
Call Transfer / Forwarding... 30
Table of Contents
Caller ID (CID).........................31
Call Waiting Caller ID............ 31
Receiving CID Records. ........... 31
Reviewing CID Records
(In CID Memory)..................... 32
Dialing a CID Number.............. 32
Storing CID Records
in Internal Memory............... 33
Deleting a CID Record............ 33
Deleting All CID Records...... 34
Programming the Phone Book...34
New Entry.................................. 34
Edit Entry................................... 35
Dialing from the Phone Book35
Delete Entry. ............................. 35
Delete All................................... 36
Call List...................................... 36
Changing the Batteries. ............37
Battery Safety Precautions. ... 37
Display Messages.......................38
Answering System Display
Messages................................38
Handset Sound Signals.............39
Troubleshooting Guide. ............39
Answering System Solutions.....41
General Product Care..............41
Causes of Poor Reception.........42
Accessory Information..............42
Warranty. ................................43
Index.........................................44
Introduction
CAUTION: When using telephone equipment,
there are basic safety instructions that should
always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this
product and save them for future reference.
IMPORTANT: Because cordless phones operate
on electricity, you should have at least one
phone in your home that isn’t cordless, in case
the power in your home goes out.
Before You Begin
Parts Checklist (for 28225xx2 Model)
Make sure your package includes the items shown here.
Base
2 AC power
adaptors
2 Battery
compartment
covers
Telephone
line cord
4 AAA
Batteries
2 Handsets
Handset
Charge Cradle
Telephone Jack Requirements
To use this phone, you need an RJ11C
Wall plate
type modular telephone jack, which
might look like the one pictured here,
Modular
installed in your home. If you don’t
telephone line
jack
have a modular jack, call your local
phone company to find out how to
get one installed.
Installation
Digital Security System
Your cordless phone uses a digital security system to protect
against false ringing, unauthorized access, and charges to
your phone line.
INSTALLATION NOTE: Some cordless
telephones operate at frequencies that may
cause or receive interference with nearby
TVs, microwave ovens, and VCRs. To minimize
or prevent such interference, the base of
the cordless telephone should not be placed
near or on top of a TV, microwave ovens, or
VCR. If such interference continues, move the
cordless telephone farther away from these
appliances.
Certain other communications devices may
also use the 1.9GHz DECT frequency for
communication, and, if not properly set, these
devices may interfere with each other and/or
your new telephone. If you are concerned
with interference, please refer to the owner’s
manual for these devices on how to properly
set channels to avoid interference. Typical
devices that may use the 1.9GHz DECT
frequency for communication include wireless
audio/video senders, wireless computer
networks, multi-handset cordless telephone
systems, and some long-range cordless
telephone systems.
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors,
fluorescent lighting, microwave ovens, heating
appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low
temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
• Never touch non-insulated telephone wires or
terminals, unless the telephone line has been
disconnected at the network interface.
• Use caution when installing or modifying telephone
lines.
Base Layout
display
page
(button)
do not disturb
(button)
charge/
in use
indicator
menu
(button)
ans on/off
(answerer
on/off
button)
memo/
record
(button)
10
volume p / q
(button)
play/stop
(button)
repeat
(button)
delete
(button)
skip
(button)
Handset Layout
redial/p
(button)
mute t
(button)
CID/q
(Caller ID
button)
display
Soft Key
Left/menu
OK (button)
format u
(button)
speaker
(button)
Soft Key
Right/intercom
(button)
talk/flash
(button)
end
(button)
repeat
(button)
mem
(phonebook
button)
stop
(button)
skip
(button)
*tone/ringer
(button)
# Key Lock
(button)
pause
(button)
microphone
Display Icons
Battery Status
Ringer OFF
Keypad Locked
In Range Icon
Active Call
Alarm ON Icon
Handsfree Active
TAM Messages
CID New Calls
Mute
11
Installing the Phone
Installing the Handset Batteries
NOTE: You must connect the handset batteries
before use.
CAUTION: To reduce the risk of fire or personal
injury, use only the Thomson Inc. approved
Model 5-2825 NiMH 1.2V 600mAh rechargeable
batteries, that are compatible with this unit.
1. Locate batteries and batteries door which are packaged
together inside a plastic bag and are separate from the
handset.
2. Locate the batteries compartment on the back of the
handset.
3. Insert the batteries as illustrated above.
4. Close the batteries compartment by pushing the door up
until it snaps into place.
12
Base Station
1. Choose an area near an electrical outlet and a telephone
wall jack (RJ11C), and place your telephone base on a level
surface, such as a desktop or tabletop.
2. Plug one end of the telephone line cord into the TEL LINE jack
on the bottom of the base and the other end into a modular
jack.
3. Plug the AC power converter into the electrical outlet and the
DC connector into the jack on the bottom of the base.
4. Place the handset in the cradle on the base.
5. The charge indicator illuminates, verifying the battery is
charging. The unit will take 20 seconds to register and verify
its security code.
6. Allow the phone to charge for 16 hours prior to first use. If
you don’t properly charge the phone, battery performance is
compromised.
CAUTION: To reduce risk of personal injury,
fire, or damage use only the 5-2822 (for base
unit) and 5-2718 (for handset charger) power
adaptor listed in the user’s guide. This power
adaptor is intended to be correctly orientated
in a vertical or floor mount position.
13
Answering System Setup
This section shows you how to set up your answering system to
receive incoming calls. Before you begin the set up process, you
must turn on the answering system.
Answering System ON/OFF
When you first plug in and activate your phone, the answering
system will be in the ON mode.
NOTE: The MESSAGES indicator illuminates when
the answering system is on.
The indicator blinks when you have new
messages.
The indicator displays “- -” when the system is
off.
1. Press the ans on/off button to turn the system ON.
2. Press the ans on/off button again to turn the system OFF.
Setting the Voice Language
1. Press the menu button repeatedly until you hear “English is
selected”. The indicator displays En. (or if Fench is select, the
indicator displays Fr).
2. Press the repeat or skip button to change the setting.
3. Press the menu button to confirm.
Recording the Outgoing Announcement
For best results when recording, you should be about nine inches
from the microphone, and eliminate as much background noise
as possible.
You may record 2 outgoing announcements in the answerer or
choose the default for your current outgoing announcement.
1. Make sure the answering system is ON.
2. Press the menu button repeatedly until you hear
“Announcement One“. The indicator displays Ar.
3. Press and hold the memo/record button to record an
announcement.
4. Begin speaking after you hear the beep.
5. Release the memo/record button when finished. Your
recording will be played automatically.
6. Repeat Steps 2 thru 5 to record Announcement 2.
14
NOTE: If you choose not to record an outgoing
announcement, a default announcement plays
instead. To return to the default announcement
after you have recorded your own outgoing
announcement, press the delete button while
the announcement is reviewing.
Sample Outgoing Announcement
Hi, this is (use your name here), I can’t answer the phone right
now, so please leave your name, number and a brief message
after the tone, and I’ll get back to you. Thanks.
NOTE: The maximum recording time for the
outgoing announcement is 2 minutes. Your
announcement must be at least 3 seconds in
length.
Remote Access Code
You can access the answering system from a tone-dial
telephone in another (remote) location.
The code is required for remote access, and it prevents
unauthorized access to your answering system. The code can be
any 3-digit number, from 000 to 999 . The pre-set code is 123.
1. Press the menu button repeatedly until you hear “Remote
access code is 123”. The indicator displays AC.
2. Press the repeat or skip button to change the setting.
3. Press the menu button to confirm.
4. Repeat Steps 2 & 3 until all 3-digits have been set. The
answering system announces the new code.
Announce Only On/Off
1. Press the menu button repeatedly until you hear “Announce
Only is On (or OFF)”. Ao shows in the display.
2. Press the repeat or skip button to change the setting.
3. Press the menu button to confirm your setting.
Message Alert
When Message Alert is ON, the answering system will beep every
10 seconds when new messages have been received.
1. Press the menu button repeatedly until you hear “Message
Alert is ON (or OFF)”. The indicator displays AL.
2. Press the repeat or skip button to change the setting.
3. Press the menu button to confirm your setting.
15
Rings to Answer
This feature lets you select the number of times you want the
phone to ring before the answering system answers a call.
1. Press the menu button repeatedly until you hear “Number of
rings selected is 3,4,5,6 or TS”. The indicator displays nr.
2. Press the repeat or skip button to choose your desired
setting.
3. Press the menu button to confirm your setting.
NOTE: If you select Toll Saver (TS) the unit
answers after the 3rd ring if there are NEW
messages, OR the unit answers after the 5th ring
if there are NO new messages. This allows user
to access their answering system from another
location and then hang up after 3 rings to save
long distance charges.
Call Screening
When call screening is ON the base speaker activates when the
system answers an incoming call. You can listen to hear who is
calling and then pick up the call if you desire.
1. Press the menu button repeatedly until you hear “Call
Screening is ON (or OFF)”. The indicator displays CS.
2. Press the repeat or skip button to change the setting.
3. Press the menu button to confirm.
16
Programming Your Phone
Main Menu
The main menu on the handset provides easy access to most of
your phone settings.
The following table outlines the Main menu items:
Answering
System
Access the answering system to listen to your
messages. Adjust many of your answering
system settings from the handset menu.
Calls List
A list of all incoming calls.
Display Setup
Customize the wallpaper, name, display
contrast, and language used on the handset.
Base Setup
Program the area code and dialing mode.
Phonebook
Create and save your own list of contacts.
Handset
Settings
Set the date/time, ringer volume, ringer tones,
alarm, etc.
During programming, you may exit the menu, keep the previous
setting and return to the standby mode, by pressing the /end
button.
Handset Settings
1. Press the the Menu (SKL) button to enter the main menu.
2. Use the
or
button to scroll to HS Settings.
3. Press the OK (SKL) button.
Date & Time
1. Use the
or
button to scroll to Date&Time through
the submenu HS Settings.
2. Press the OK (SKL) button to enter Date&Time. Enter the date
(MM:DD:YY) using the number keypad.
3. Press the OK (SKL) button. Enter the time (HH:MM) using the
number keypad.
4. Press the
button to switch the format (AM or PM
or 24 hr.).
5. Press the OK (SKL) button to confirm the Date & Time setting.
17
Ringer Setup
Ringer Volume
1. Use the
or
button to scroll to Ringer Setup through
the submenu HS Settings.
2. Press the OK (SKL) button.
3. Use the
or
button to scroll to Ringer Volume.
4. Press the OK (SKL) button.
5. Use the
or
button to select the ringer volume: Ringer
Volume 1, Ringer Volume 2, Ringer Volume 3, Ringer Volume
4, Ringer Volume 5 or OFF.
6. Press the OK (SKL) button to confirm.
Ringtone
1. Use the
or
button to scroll to Ringtone through the
submenu Ringer Setup.
2. Press the OK (SKL) button.
3. Use the
or
button to select one type of ring tone (14
ring melodies).
4. Press the OK (SKL) button to confirm the ring type.
Intercom Ringtone
1. Use the
or
button to scroll to Int. Ringtone through
the submenu Ringer Setup.
2. Press the OK (SKL) button.
3. Use the
or
button to select one type of ring tone (14
ring melodies).
4. Press the OK (SKL) button to confirm the ring type.
Group Melody
1. Use the
or
button to scroll to Group Melody through
the submenu Ringer Setup.
2. Press the OK (SKL) button. There are 6 pre-set caller groups:
VIP, Business, Family, Friends, School and Others.
3. Use the
or
button to choose one of the groups.
4. Press the OK (SKL) button.
5. Use the
or
button to select one type of ring tone (14
ring melodies).
6. Press the OK (SKL) button to confirm.
7. Repeat steps 3-6 as needed.
18
Set Alarm
1. Use the
or
button to scroll to Set Alarm through the
submenu HS Settings.
2. Press the OK (SKL) button.
3. Use the
or
button to choose Set Alarm or Alarm
Tone.
4. Press the OK (SKL) button .
If you select [Set Alarm]:
or
button to select OFF, Once or Daily.
1. Use the
2. Press the OK (SKL) button. Enter the time (HH:MM).
3. Press the OK (SKL) button to confirm the setting.
If you select [Alarm Tone]:
or
button to select one type of ring tone (14
1. Use the
ring melodies).
2. Press the OK (SKL) button to confirm the setting.
Auto Talk
The automatic talk function enables the incoming call to be
taken immediately when the handset is removed from the base
station.
or
button to scroll to Auto Talk through the
1. Use the
submenu HS Settings.
2. Press the OK (SKL) button.
3. Use the
or
button to select OFF or ON.
4. Press the OK (SKL) button to confirm the setting.
Registration
1. Use the
or
button to scroll to Registration through
the submenu HS Settings.
2. Press the OK (SKL) button.
Register Handset
1. Press and hold the page button on the base station
for 5 seconds until acknowledgement signal is heard.
2. Use the
or
button to scroll to Register Handset
through the submenu Registration.
3. Press the OK (SKL) button.
4. Use the
or
button to select Base1, Base2, Base3 or
Base4.
5. Press the OK (SKL) button. SEARCHING shows in the handset
display.
19
NOTE:
1. Once the registration procedure is complete,
the handset will automatically be allocated the
next available handset number.
2. Once the Page button is pressed and held
for more than 10 seconds on a base station,
the base stays in registration mode for approx.
2 minutes. While the handset searches for an
available base station, the screen displays
SEARCHING.
Deregister Handset
WARNING: It is not recommended that a handset
be deregistered unless absolutely necessary
because once a handset is deregistered, that
handset’s telephone features cannot be used
until the handset is re-registered.
1. Use the
or
button to scroll to Deregister HS through
the submenu Registration.
2. Press the OK (SKL) button.
or
button to select the handset
3. If necessary, use the
and press OK (SKL) button. “Deregister HS?” shows in the
display.
4. Press the OK (SKL) button to confirm.
Select Base
1. Use the
or
button to scroll to Select Base through
the submenu HS Settings.
2. Press the OK (SKL) button.
3. Use the
or
button to select a specific base.
4. Press the OK (SKL) button to confirm the selection.
Tones ON/OFF
1. Use the
or
button to scroll to Tones ON/OFF through
the submenu HS Settings.
2. Press the OK (SKL) button.
3. Use the
or
button to choose Key tone, Battery Low
and Out of Range.
4. Press the OK (SKL) button.
5. Use the
or
button to select OFF or ON.
6. Press the OK (SKL) button to confirm the selection.
7. Repeat steps 3-6 as needed.
20
Reset Handset
1. Use the
or
button to scroll to Reset Handset through
the submenu HS Settings.
2. Press the OK (SKL) button. “Default Reset?” shows in the
display.
3. Press the OK (SKL) button to reset to the default settings or
press Back (SKR) button to cancel.
Handset Display Settings
1. Press the Menu (SKL) button to enter the main menu.
2. Use the
or
button to select Display Setup.
3. Press the OK (SKL) button.
Wallpaper
1. Use the
or
button to scroll to Wallpaper through the
submenu Display Setup.
2. Press the OK (SKL) button.
3. Use the
or
button to select the desired wallpaper or
Wallpaper Off.
4. Press the OK (SKL) button to confirm the selection.
Handset Name
1. Use the
or
button to scroll to Handset Name through
the submenu Display Setup.
2. Press the OK (SKL) button.
3. Enter the handset name using the keypad (press the Clear
(SKR) button to delete any incorrect characters).
NOTE: Use the */tone/ringer button to change
keyboard entry from upper/lower case and
special characters.
4. Press the OK (SKL) button to confirm.
Display Contrast
1. Use the
or
button to scroll to Display Contrast
through the submenu Display Setup.
2. Press the OK (SKL) button.
3. Use the
or
button to adjust the contrast level (1-8).
4. Press the OK (SKL) button to confirm the setting.
21
Handset Language
1. Use the
or
button to scroll to Language through the
submenu Display Setup.
2. Press the OK (SKL) button.
3. Use the
or
button to select the language.
4. Press the OK (SKL) button to confirm the setting.
Base Setup
1. Press the Menu (SKL) button to enter the main menu.
2. Use the
or
button to select Base Setup.
3. Press the OK (SKL) button.
Area Code
1. Use the
or
button to scroll to Area Code through the
submenu Base Setup.
2. Press the OK (SKL) button.
3. Enter the Area Code using the number keypad, delete any
incorrect digits by pressing Clear (SKR) button.
4. Press the OK (SKL) button to confirm setting.
Dial Mode
1. Use the
or
button to scroll to Dial Mode through the
submenu Base Setup.
2. Press the OK (SKL) button.
3. Use the
or
button to select TONE or PULSE.
4. Press the OK (SKL) button to confirm the selection.
NOTE: If PULSE dialing is selected, press the
*/tone/ringer button to temporarily change to
TONE mode. It will reset automatically when the
pulse call is completed.
22
Answering System Setup via the Handset
1. Press the Menu (SKL) button to access the Main menu.
2. Press the OK (SKL) button again to access the Answer
System menu.
Answering System ON/OFF
1. Use the
or
to scroll to Answer On/Off through the
submenu Answer System.
2. Press the OK (SKL) button.
3. Use the
or
to select Answer On or Answer Off.
4. Press the OK (SKL) to confirm your setting.
Rings to Answer
1. Use the
or
to scroll to Rings to answer through the
submenu Answer System.
2. Press the Soft Key Left (SKL) button.
3. Use the
or
to choose between 3 rings, 4 rings, 5
rings, 6 rings or Toll Saver.
4. Press the OK (SKL) to confirm your setting.
Message Alert
1. Use the
or
to scroll to Message Alert through the
submenu Answer System.
2. Press the OK (SKL) button.
3. Use the
or
to toggle between On or Off.
4. Press the OK (SKL) to confirm your setting.
Setting the Voice Language
1. Use the
or
key to choose the selection Voice
Language through the submenu Answer System.
2. Press the OK (SKL) button.
3. Use the
or
key to select the language.
4. Press the OK (SKL) button to confirm the setting.
Remote Access Code
1. Use the
or
to scroll to Change RemotePIN through
the submenu Answer System.
2. Press the OK (SKL) button.
3. Press the CLear (SKR) to clear the PIN number. Enter a new
3-digit number using the number keypad.
4. Press the OK (SKL) to confirm the new number.
23
Answering System Operation
Listening to Your Messages
When you have new messages, the indicator will flash. Recorded
messages and memos are retained until you delete them.
Your Answering System has approximately 12 minutes of storage
capacity (or 59 messages/memos). If its capacity is full, the
system will answer after 10 rings.
Message Playback
On the base:
1. Press the play/stop button. The prompt will tell you how
many new messages are stored in the Mailbox. If there are
one or more new messages, only the new messages will be
played.
2. Press the play/stop button again to hear old messages after
new message playback is completed. Before each message
is played, the day and time it was recorded is announced.
From the Handset Menu:
1. Press the Menu (SKL) button to access the Main menu.
2. Press the OK (SKL) button again to access the Answer
System menu.
3. Use the
or
to scroll to Play Messages.
4. Press the OK (SKL) button. Messages will be played.
5. Press the STOP (SKL) to stop message playback or press the
DEL (SKR) to delete current message.
Deleting Messages
You may erase messages in the following three ways:
To delete the message or memo currently playing on the base:
1. Press and release play/stop button.
2. Press the review and skip buttons to select and play the
message you want to erase.
3. Press the delete button, the current message is erased, and
the next message plays.
To delete all old messages stored in the Mailbox:
1. In the idle mode, press and hold the delete button. The
system will announce, “All old Messages erased”.
2. All old messages will be deleted.
24
To delete all old messages with the handset :
1. Press the Menu (SKL) button to access the Main menu.
2. Press the OK (SKL) button again to access the Answer
System menu.
3. Use the
or
to scroll to Delete All Mess.
4. Press the OK (SKL) button. Erase All Msg.? shows in the
display.
5. Press the YES (SKL) button to erase all messages or press NO
(SKR) button to cancel.
NOTE: New, unplayed messages cannot be
deleted until you play them. Once you delete the
message, it cannot be recovered.
Base Ringer Volume
In idle mode, press the volume (p or q) buttons to adjust the
volume from Off to Level 5.
Memo Recording
You can record a memo, either at the base unit or from a remote
location.
To record a Memo at the Base:
1. Press the and hold the memo/record button.
2. The system announces, “Now Recording”. Begin speaking
after the beep.
3. Release the memo/record button when finished. Your memo
is stored like a message from an outside caller.
To record a Memo from the Handset:
1. Press the Menu (SKL) button to access the Main menu.
2. Press the OK (SKL) button again to access the Answer
System menu.
3. Use the
or
to scroll to Record memo.
4. Press the OK (SKL) button. You will hear “Now Recording,”
followed by a beep. You may now record a memo.
5. Press the STOP (SKR) to stop recording. Your memo is stored
like a message from an outside caller.
NOTE: If memory is full, the answering system
will announce “Memory is Full”, and the message
indicator flashes an “F “.
25
Memory Full
When the answering system memory is full, the system answers
after 10 rings, beeps and waits for the 3-digit security code. If
you don’t enter the security code within 8 seconds , the phone
hangs up. You should erase some messages so the answering
system can record new messages.
NOTE: The unit also answers after the 10th ring if
it is turned OFF. To access the answering system,
enter your 3-digit security code.
Important Information
NOTES: There is a total of 12 minutes of
recording time. This includes messages, memos,
and announcements.
The maximum number of messages that can be
stored is 59.
A maximum of 2 minutes is allotted for each
message, memo, or announcement.
If a call comes in while you are listening to
messages, playback automatically stops.
Remote Operation
1. Call your answering system from any touch-tone phone.
2. When you hear your outgoing announcement, enter your
3-digit Remote Access code.
3. You can perform the following functions:
• Press the (2) to play messages
• Press the (2) to stop
• Press the (0) to delete current message
• Press the (1) to repeat
• Press the (3) to skip
• Press the (4) to toggle answer on/off
• Press the (7) to review menu again
26
Handset Operation
Making a Call
Pre-Dialing:
1. Dial the telephone number. Use the Clear (SKR) button to
delete any incorrect entries.
OR
Use the
,
, or mem button to select desired number,
press the More (SKL) and scroll to Use Number.
2. Press the /flash button. It will start counting when the call
is connected, the call timer format is HH:MM:SS.
3. Press the /end button to terminate the call.
Dialing:
1. Press the /flash button and wait for the dial tone.
2. Dial the telephone number as required. It will start counting
when the call is connected, the call timer format is HH:MM:
SS.
OR
Press the MORE (SKL) button to choose from Redial, Calls
List, or Phone Book, press the OK (SKL) button.
3. Use the
, or
, button to select desired number,and
press the OK (SKL) button.
4. Press the /end button to terminate the call.
NOTE: During the conversation, you can use
or
button to adjust the speaking volume (5
levels).
Receiving a Call
When an external call is received, all handsets registered and
the base station ring , and flashes in the handset display. If
configured, the telephone number of the caller appears (network
depended). If the caller has been entered in your phone book, the
name appears. On the base, the blue charge/in use indicator will
flash according to the ring cadence.
1. Press the /flash button to establish the connection.
NOTE: If auto answer is enabled, the call is
connected when the handset is lifted from the
base.
2. Press the
/end button to terminate the call.
27
Redialing
The phone stores the last 10 numbers dialed in the redialling
memory.
1.
2.
3.
4.
Press the
Use the
Press the
Press the
button to view the dialed calls.
or
button to select the desired record.
/flash button to redial the desired record.
/end button to terminate the call.
Changing the Earpiece Volume
Press the
or
button as often as necessary to change the
earpiece volume during a call.
Handset Speaker Phone
Press the
button to activate/de-activate the handset speaker.
Muting the Microphone
Press the </mute button to mute your connection, the screen
displays the
icon. To cancel and return to normal connection,
press the </mute button again.
DND (Do Not Disturb)
The do not disturb feature (DND) allows you to mute the ringer of
all registered handset(s) at the same time. The phone must be in
standby mode. Press the DND button on the base, you will hear
a confirmation tone, and the DND LED illuminates. To cancel the
DND feature, press the DND button again. You can also mute
the ringer tone while the phone is ringing by pressing the DND
button on the base.
Muting the Ringer during an Incoming Call
Press the /end button during an Incoming call to stop the ring
on the handset. Your answering system will continue to monitor
the ring.
Disabling the Ringer on the Handset
Press the and hold the */tone/ringer button for 1.5 seconds in
idle mode to activate or deactivate the handset Ringer. The
icon turns ON or OFF.
28
Paging the Handset
If a handset has been misplaced, it is possible to call all the
handsets. The handset will ring at full volume regardless of
any programmed pre-set.
1. Press the page button briefly on the base station.
To stop the page call:
1. Quickly press and release the /flash, /end, or
button on the handset or page button on the base.
Key Lock
Press the and hold the
de-activate the key lock.
button for 2 seconds to activate or
When handset keys are locked, you are still able to receive
incoming calls by pressing the /flash button.
Intercom Operation
Making Intercom Calls
If more than one handset is registered on the base station, it is
possible to make intercom calls between the handsets.
1. Press the INT (SKR) button.
2. Use the
or
button to select the required handset
(Handset 1 or Handset 2).
3. Press the OK (SKL) button to initiate the conversation.
4. Press the /end button to end the call.
NOTE: During the conversation, you can use
or
button to adjust the speaking volume (5
levels).
Receiving Intercom Calls
When an intercom call arrives, the handset rings and displays
the caller’s handset number.
flashes in the handset display.
1. Press the /flash button to establish the connection.
NOTE: If auto answer is enabled, the line can also
be automatically connected after the handset is
lifted up from the base.
2. Press the
/end button to terminate the call.
29
Three Party Conference
After have received an external call, it is possible to include a
second handset in the conversation (three way conference).
1. Press the INT (SKR) button to initiate an intercom call.
2. Use the
or
button to select the required handset
(Handset 1 or Handset 2) that needs to participate in the
conference (e.g. 2).
3. Press the OK (SKL) button to establish the conference call
after the other handset answered the intercom call.
4. Press the /end button to disconnect from the conference
call and the other handset continues with the external call.
Call Transfer / Forwarding
It is possible to put external calls on hold and call other handsets
registered to the base or to forward calls.
After receiving an external call;
1. Press the Int (SKR) button to place the external call on hold
and initiate an intercom call.
2. Use the
or
button to select the required handset
(Handset 1 or Handset 2). The target handset will ring.
3. After the intercom connection is made, press the /end
button to transfer the external call to the desired handset.
NOTE:
1. There must be more than two handsets
registered to the base, otherwise the call
transfer/forwarding function will be invalid.
2. If the /end button is pressed before another
handset answers the intercom call, the call
transfer procedure will be cancelled and the
external call is regained.
30
Caller ID (CID)
IMPORTANT: In order to use this unit’s Caller
ID features, you must subscribe to either the
standard Name/Number Caller ID Service or Call
Waiting Caller ID Service. To know who is calling
while you are on the phone, you must subscribe
to Call Waiting Caller ID Service.
This unit receives and displays information transmitted by your
local phone company. This information can include the phone
number, date, and time; or the name, phone number, date, and
time.
Call Waiting Caller ID
Provided you subscribe to Call Waiting Caller ID service from
your phone company; if you receive an incoming call and you
are using the GE multi handset system, a beep indicates the
presence of a Call Waiting call on the line. The Call Waiting Caller
ID information will be displayed and stored in the history of all
handsets in the system.
• When you hear the call waiting beep in the handset receiver,
press the talk button to put the current call on hold and
answer the incoming call. Press the talk or speaker button to
return to the original call.
Receiving CID Records
When you receive a call, the Caller ID information is transmitted
between the first and second ring. The Caller ID information
appears on the display while the phone rings, giving you a
chance to monitor the information and decide whether or not to
answer the call.
31
Reviewing CID Records (In CID Memory)
If you are not at home or cannot answer, your telephone’s Caller
ID memory stores the data for the 30 most recent calls you
received so you can see who called while you were unavailable.
When the 31st call is received, the oldest Caller ID record (1st call)
is automatically deleted.
You may review the stored information at any time. Calls
received since your last review show as
in the display.
As calls are received and stored, the display is updated to let you
know how many calls have been received. To scroll CID records:
1. Make sure the phone is OFF (not in TALK mode).
2. Press the
3. Use the
button.
or
buttons to review the CID records.
Dialing a CID Number
1. Make sure the phone is OFF (not in TALK mode).
2. Press the
button.
or
buttons to review the CID records.
3. Use the
4. Lift the receiver or press the /flash or button on the
cordless handset, the number is automatically dialed out.
NOTE: Depending on (a) how the incoming
caller’s phone number is formatted when it is
received, and (b) whether or not you previously
pre-programmed your local area code into the
set up menu, you may need to adjust the format
of the incoming caller’s stored phone number
before making the call, press the format u
button to adjust the number, and try again.
Available formats include:
Number of digits Eleven digits
Explanation Example
long distance code “1 ” 1-317-888-8888
+3-digit area code
+7-digit telephone number.
Ten digits3-digit area code +317-888-8888
7-digit telephone number.
Seven digits
32
7-digit telephone number.888-8888
Storing CID Records in Internal Memory
You may also store CID information in the phone’s internal
memory.
NOTE: It is important that you format CID records
correctly BEFORE storing in internal memory
as you cannot reformat CID records stored
in memory.
1. Make sure the phone is OFF (not in talk mode).
2. Press the
button.
3. Use the
or
buttons to scroll to the desired CID
record.
4. Press the More (SKL) button and then use the
or
buttons to select the submenu Save Number.
5. Press the OK (SKL) button and use the keypad to enter a
name (up to15 characters).
NOTE: Use the */tone/ringer button to change
keyboard entry from upper/lower case and
special characters.
6. Press the OK (SKL) button and use
or
select a Group or No Group.
7. Press the OK (SKL) button to confirm.
button to
Deleting a CID Record
1. Make sure the phone is OFF (not in TALK mode).
2. Press the
button.
or
buttons to display the CID record you
3. Use the
want to delete.
4. Press the More (SKL) button and then use the
or
buttons to select the submenu Delete Entry.
5. Press the OK (SKL) button to delete the entry, and the screen
displays “Delete?”.
6. Press the Yes (SKL) button to confirm.
NOTE: Press the end button to return to the
standby mode without deleting any CID records.
33
Deleting All CID Records
1. Make sure the phone is OFF (not in TALK mode).
2. Press the
button.
or
buttons to display any Caller ID record.
3. Use the
4. Press the More (SKL) button and then use the
or
buttons to select the submenu Delete All.
5. Press the OK (SKL) button and the screen displays “Delete
All?”.
6. Press the Yes (SKL) button to confirm.
NOTE: Press the end button to return to the
standby mode without deleting any CID records.
Programming the Phone Book
The telephone can store up to 50 entries in the phone book. Store
numbers frequently used in order to be able to dial them quickly
and easily. When the function is supported by the telephone
provider service and the caller, the handset displays the name of
the caller (when stored in the phone book).
New Entry
1.
2.
3.
4.
5.
Press the Menu (SKL) button to enter the main menu.
Use the
or
button to select Phone Book.
Press the OK (SKL) button to enter menu.
Press the More (SKL) button.
Use the
or
button to select New Entry and press the
OK (SKL) button.
Enter number (max. 24 digits) and press the OK (SKL) button
when finished.
Enter name (max. 15 characters) and press the OK (SKL)
button when finished.
NOTE: Use the */tone/ringer button to change
keyboard entry from upper/lower case and
special characters.
6. Use the
or
button to select a Group or No Group.
There are 6 pre-set caller groups: VIP, Business, Family,
Friends, School and Others.
7. Press the OK (SKL) button to confirm the selection and store
the entry.
NOTE: When the capacity is full, Memory full will
display. Any incorrect input can be deleted by
pressing Clear (SKR) button.
34
8. User can also save number into phone book through call list
(refer to Call List section).
Edit Entry
Press the Menu (SKL) button to enter the main menu.
Use the
or
button to select Phone Book.
Press the OK (SKL) button to enter menu.
Use the
or
button to select a desired entry.
Press the More (SKL) button to access Phone Book menu,
and then use the
or
to select the submenu Edit
Entry.
6. Press the OK (SKL) to enter the number field, press the OK
(SKL) button again to senter the name field, press the OK
(SKL) button again to select Caller Groups .
7. Press the OK (SKL) button to confirm.
NOTE: Press the Clear (SKR) key to delete any
incorrect input.
1.
2.
3.
4.
5.
Dialing from the Phone Book
1. Press the mem button when in standby mode, the first entry
in the phone book appears.
NOTE: If there is no record in phone book, the
screen displays, Empty and it will automatically
return to the main menu.
2. Use the
or
button to select the required record from
the phone book.
3. Press the /flash button to dial the number.
4. Press the /end button to terminate the call.
NOTE: To store entries in the phone book , please
refer to “Phone Book” section.
Delete Entry
Press the Menu (SKL) button to enter the main menu.
Use the
or
button to select Phone Book.
Press the OK (SKL) button to enter menu.
Use the
or
button to select a desired entry.
Press the More (SKL) button to access Phone Book menu,
and then use the
or
to select the submenu Delete
Entry.
6. Press the OK (SKL) button to delete the entry, and the screen
displays “Delete?”.
7. Press the Yes (SKL) button to confirm.
1.
2.
3.
4.
5.
35
Delete All
Press the Menu (SKL) button to enter the main menu.
Use the
or
button to select Phone Book.
Press the OK (SKL) button to enter menu.
Press the More(SKL) button to enter menu.
Use the
or
to select the submenu Delete All.
Press theOK (SKL) button to delete the entry, and the screen
displays “Delete All PB?”
7. Press the Yes (SKL) button to confirm.
NOTE: User can access Phone Book directly from
standby mode by pressing mem button.
1.
2.
3.
4.
5.
6.
Call List
IMPORTANT: To use the “Call List” function, you
must subscribe to your network operator’s
Caller Identification (CID) service.
Call List can contain up to 30 records.
1. Press the Menu (SKL) button to enter the main menu.
2. Use the
or
button to select Calls List.
3. Press the OK (SKL) button to enter Calls List.
NOTE: If there is no record in call log, empty
information will display.
4. Use the
or
button to find the desired record.
5. Press the More (SKL) button.
6. Use the
or
button to scroll to Delete Entry, Save
Number, Delete All or Use number.
If you choose Delete Entry:
1. Press the OK (SKL) button to delete the entry, and the screen
displays “Delete?”.
2. Press the Yes (SKL) button to confirm.
If you choose Save Number:
1. Press the OK (SKL) button to enter the name field, press the
OK (SKL) button again to select Caller Groups.
2. Press the OK (SKL) button to save the record to the phone
book.
NOTE: Press the Clear (SKR) key to delete any
incorrect input.
36
If you choose Delete All:
1. Press the OK (SKL) button to delete the entry, and the screen
displays “Delete All?”.
2. Press the Yes (SKL) button to confirm.
If you choose User Number:
Press OK (SKL) button to view user number, you may then redial
the number or save it to Calls List or Phone Book
Changing the Batteries
CAUTION: To reduce the risk of fire or personal
injury, use only the Thomson Inc. approved
Model 5-2825 NiMH 1.2V 600mAh rechargeable
batteries, that are compatible with this unit.
1. Make sure the telephone is OFF (not in TALK mode) before
you replace the batteries.
2. Remove the batteries compartment door.
3. Disconnect the cord attached to the batteries and remove
the batteries from the handset.
4. Insert the new batteries and connect the cord to the jack
inside the batteries compartment.
5. Put the batteries compartment door back on.
6. Place handset in the base to charge. Allow the handset
batteries to properly charge (for 16 hours) prior to first
use or when you install the new batteries. If you do not
properly charge the phone, the batteries performance will
be compromised.
Battery Safety Precautions
• Do not burn, disassemble, mutilate, or puncture. Like other
batteries of this type, toxic materials could be released which
can cause injury.
• To reduce the risk of fire or personal injury, use only the
battery listed in the User’s Guide.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
NOTE: The RBRC seal on the battery used in your Thomson Inc. product
indicates that we are participating in a program to collect and recycle the
rechargeable battery (or batteries).
For more information go to the RBRC web site at www.rbrc.org
or call 1-800-8-BATTERY or contact a local recycling center.
37
Display Messages
The following indicators show the status of a message, provides
Caller ID information, or helps you set up and use your phone.
DELETE ALL PB?
Prompt asking if you want
to erase all records.
DELETE?
Prompt asking if you want
to erase the current records.
ERASE ALL MSG.? Prompt asking if you want
to erase all messages.
NO LINE
Indicates that the telephone line is not
connected.
RECORDING
Indicates it is recording a memo.
SEARCHING
Indicates handset is too far away
from the base, and the handset is
searching for the base.
PAGING
Someone pressed the PAGE button
on the base.
ANSWER ON
Indicates the answering system is set to ON.
ANSWER OFF
Indicates the answering system
is set to OFF.
Answering System Display Messages
The following messages show the status of the answering
system or help you set up and use the system.
Ao
Ac
AL
Ar
CS
En
F
Fr
nr
38
Indicates “Announce Only”.
Indicates “Remote Access Code”.
Indicates “Message Alert”.
Indicates “Announcement”.
Indicates “Call Screening”.
Indicates “English” is selected language in voice menu.
Indicates “Memory Full”.
Indicates “French” is selected language in voice menu.
Indicates “Number of Rings”.
Handset Sound Signals
Signal
Meaning
A long warbling tone Signals an incoming call
(with ringer on)
Three short beeps (several times)
Page signal
Single beep every 7 seconds Low battery warning
Troubleshooting Guide
Cordless Phone Solutions
No Display
• The battery must be fully charged. Try replacing the
battery.
Registration will not work
• The battery must be fully charged. Charge the battery for
16 hours.
• Make sure that the unit is connected to a non-switched
electrical outlet. Disconnect the unit from the wall and plug
it in again.
• You must be subscribed to Caller ID service from your local
telephone company in order to receive Caller ID records. Telephone Solutions
No dial tone
• Check installation:
Make sure the base power cord is connected to a working
electrical outlet.
Make sure the telephone line cord is connected to the base
unit and the wall phone jack.
• Connect another phone to the same modular jack; if the
second phone doesn’t work, the problem might be with
your wiring or local service.
• The handset may be out of range of the base. Move closer
to the base.
• Make sure the battery is properly charged (for 16 hours).
• Ensure the battery pack is installed correctly.
• The handset should beep when you press the talk button,
and the charge indicator on the base should be lit when
the handset rests in the cradle. If not, the battery may need
to be charged.
39
• Place the handset in the base for at least 20 seconds to
reset unit.
Handset does not ring
• Make sure the handset ringer is turned ON.
• Move closer to the base. The handset may be out of range.
• You may have too many extension phones on your line. Try
unplugging some phones.
• Check for a dial tone.
You experience static, noise, or fading in and out • Move closer to base. The handset might be out of range.
• Relocate the base. Make sure base is not plugged into an
electrical outlet with another household appliance.
• Charge the battery.
Unit beeps
• Place handset in base for 20 seconds; if it still beeps,
charge battery for 16 hours.
• Clean the charging contacts on handset and base with a
soft cloth.
• See solutions for “No dial tone.”
• Replace the battery.
Unit locks up and there is no communication between the
handset and base
• Unplug the power adaptor from the electrical outlet and
the back of the base. Remove the handset battery. Wait for
30 seconds and plug the power adaptor back into the base
and electrical outlet. Reconnect the battery and charge for
16 hours.
Battery Solutions
If you experience any of the following problems, even after
recharging the battery, you may need to replace the battery
pack:
40
• Short talk time
• Poor sound quality.
• Limited Range
Answering System Solutions
Can’t hear messages, beep, etc.
• Adjust speaker volume.
Time/Day setting stuck at 12 a.m Mon.
• Set the time clock.
Answers on 10th ring
• Make sure answering system is turned on.
• Answering system memory may be full. Erase some
messages.
Incoming messages are incomplete
• An extension phone may have been lifted as a message is
received.
• Answering system memory is full. Erase some messages.
• You may have accidently pressed the play/stop button
during playback and stopped the message.
Won’t respond to remote commands
• You must use a tone-dial phone. This phone does not
support pulse (rotary) dialing.
• Make sure to enter the correct security code.
• Did unit hang up? If you take no action for a period of time, it
automatically hangs up.
General Product Care
To keep your telephone working and looking good, follow these
guidelines:
• Avoid putting the phone near heating appliances and
devices that generate electrical noise (for example, motors
or fluorescent lamps ).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping the unit and other rough treatment.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
• Retain the original packaging in case you need to ship the
phone at a later date.
• Periodically clean the charge contacts on the handset and
base with a soft cloth.
41
Causes of Poor Reception
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction that can shield
radio signals.
• You’re too close to appliances such as microwaves, stoves,
computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of the
house.
• Base is plugged into AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
• You’re out of range of the base.
• Microwave oven is using the same frequency.
Accessory Information
DESCRIPTION
MODEL NO.
AC Power Adaptor
5-2822
Handset Replacement Battery
5-2825
Handset Charger Power Adaptor
5-2718
Handset Charger Cradle
5-2835
To order, call the nearest distributor for your area;
Ontario: (905) 624-8516
Manitoba: (204) 783-2088
British Columbia: (604) 438-8001 Quebec: (514) 352-9071
A shipping and handling fee will be charged upon ordering. It is
required by law to collect appropriate sales tax for each individual
state, country, and locality to which the merchandise is being
sent. Items are subject to availability.
42
Warranty
Thomson Multimedia Ltd., warrants to the purchaser or gift
recipient that if any manufacturing defect becomes apparent in
this product within 1 year from the original date of purchase, it
will be replaced free of charge, including return transportation.
This warranty does not include damage to the product resulting
from accidents, misuse or leaking batteries.
Should your product not perform properly during the warranty
period, either:
1. Return it to the selling dealer with proof of purchase for
replacement,
OR
2. Call 1-800-522-0338 (English) or 1-800-522-0445 (French) for
instructions concerning where to mail the product.
The provisions of this written warranty are in addition to and not
a modification of or subtraction from the statutory warranties
and other rights and remedies contained in any applicable
legislation, and to the extent that any such provisions purport
to disclaim, exclude or limit any such statutory warranties and
other rights and remedies, such provisions shall be deemed to
be amended to the extent necessary to comply therewith.
Attach your sales receipt to this booklet for future reference. This
information is required if service is needed during the warranty
period.
PURCHASE DATE _ ______________________________________________
NAME OF STORE _______________________________________________
43
Index
A
Accessory Information
42
Announce Only On/Off
15
Answering System Display
Messages38
Answering System ON/OFF
14
Answering System ON/OFF23
Answering System Operation24
Answering System Setup
14
Answering System Setup via the
Handset23
Answering System Solutions 41
Area Code22
Auto Talk
19
B
Base Layout
10
Base Ringer Volume25
Base Setup22
Base Station
13
Battery Safety Precautions37
Before You Begin
7
C
Call List36
Call Screening
16
Call Transfer / Forwarding30
Call Waiting Caller ID31
Caller ID (CID)31
Causes of Poor Reception
42
Changing the Batteries37
Changing the Earpiece Volume28
D
Date & Time
17
Delete All36
Delete Entry35
Deleting a CID Record33
Deleting All CID Records34
Deleting Messages24
Deregister Handset20
Dial Mode22
Dialing a CID Number32
Dialing from the Phone Book35
Dialing:27
Digital Security System8
Disabling the Ringer on the
Handset28
44
Display Contrast21
Display Icons
11
Display Messages38
DND (Do Not Disturb)28
E
Edit Entry35
External Ringtone 18
F
FCC RF Radiation Exposure
Statement
4
G
General Product Care
Group Melody
41
18
H
Handset Display Settings21
Handset Language22
Handset Layout
11
Handset Name21
Handset Operation27
Handset Sound Signals39
Handset Speaker Phone28
Hearing Aid Compatibility (HAC)3
I
Important Information2
Important Information26
Important Installation Guidelines9
Information for DECT Product
4
Installation 8
Installing the Handset Batteries 12
Installing the Phone
12
Intercom Operation29
Intercom Ringtone
18
Interference Information2
Introduction
7
K
Key Lock29
L
Licensing3
Listening to Your Messages24
Index
M
S
Main Menu
17
Making a Call27
Making Intercom Calls29
Memo Recording25
Memory Full26
Message Alert
15
Message Alert23
Message Playback24
Muting the Microphone 28
Muting the Ringer during an
Incoming Call28
Select Base20
Set Alarm
19
Setting the Voice Language
14
Setting the Voice Language23
Storing CID Records in Internal
Memory33
T
New Entry34
Table 7
Telephone Jack Requirements 7
Telephone Network Information3
Three Party Conference30
Tones ON/OFF20
Troubleshooting Guide39
P
W
Paging the Handset29
Parts Checklist 7
Pre-Dialing:27
Programming the Phone Book34
Programming Your Phone
17
Wallpaper21
Warranty
43
N
R
Receiving a Call27
Receiving CID Records31
Receiving Intercom Calls29
Recording the Outgoing
Announcement
14
Redialing28
Register Handset
19
Registration
19
Remote Access Code
15
Remote Access Code23
Remote Operation26
REN Number3
Reset Handset21
Reviewing CID Records (In CID
Memory)32
Ringer Setup
18
Ringer Volume
18
Rings to Answer
16
Rings to Answer23
45
Visit the GE website at: www.GE.com/phones
Model 28225
00025100 (Rev. 3 CAN E)
08-30
Printed in China
Thomson Multimedia Ltd.
30 Eglinton Ave W., Suite 304
Mississauga, ON Canada L5R 3E7
© 2008 Thomson Multimedia Ltd.
Trademark(s) ® Registered
Marque(s) ® déposée(s)