Owner`s manual | Garmin 110 Network Card User Manual

®
110
2-way radio & personal navigator®
owner’s manual
© Copyright 2002–2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street
Olathe, Kansas 66062, U.S.A.
Tel. 913/397.8200 or 800/800.1020
Fax 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle
Abbey Park Industrial Estate
Romsey, SO51 9DL, U.K.
Tel. 44/0870.8501241
Fax 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated,
downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants
permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy
of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this
copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make
changes in the content without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site
(www.garmin.com) for current updates and supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, AutoLocate®, Personal Navigator®, MapSource®, TracBack®, BlueChart®, and Rino® are registered trademarks of Garmin Ltd. or its
subsidiaries and may not be used without the express permission of Garmin.
January 2005
Part Number 190-00251-10 Rev. D
Printed in Taiwan
INTRODUCTION
INTRODUCTION
Thank you for choosing the Garmin® Rino® 110 (Radio
Integrated with Navigation for the Outdoors). To get the
most from your new Rino 110, read through the Quick
Start Guide first, then this Owner’s Manual to understand
all of the operating features.
The Quick Start Guide describes the process of setting
up your Rino 110 and some basic unit operations to
familiarize you with your new Rino 110 right out of the
box. The small size of the guide makes it perfect to take
with you!
This Owner’s Manual describes the Main Pages of the
Rino 110 and their options in detail. While the Owner’s
Manual provides some direction on how to select and
change items, its main intention is to describe each Main
Page, Option Menu, and feature in detail.
Rino® 110 Owner’s Manual
This manual is organized into the following sections:
The Introduction section provides the Table of Contents
and safety information.
The Getting Started section provides basic information
about the Rino 110.
The Unit Operation section provides information on
each of the five Main Pages, listed in the same order as
viewed on the unit. The section for each Page provides
an overview that discusses the page, how it functions,
and step-by-step instructions for using the page and its
features. It also includes an overview of some additional
features and step-by-step instructions for using the
features.
The Appendix includes additional information about the
Rino 110.
The Index provides keywords and the pages on which
they appear.
i
INTRODUCTION > TABLE OF CONTENTS
Introduction.............................................................i
Getting to Know Your Rino 110 ............................1
Front of the Rino 110................................................ 2
Back of the Rino 110 ................................................ 3
Main Page Sequence................................................ 4
Operating the Rino 110 ............................................ 5
Status Bar Overview ................................................ 6
Unit Operation........................................................7
Radio Page ................................................................ 7
Initializing the Rino 110 ................................................ 7
Using My ID and Symbol Fields ................................... 8
Setting the Channel and Squelch Code........................ 10
Scanning and Monitoring ............................................ 12
Radio Page Option Menu ............................................ 14
Setup Radio ............................................................ 14
Setup Tones ............................................................ 15
Setup Scanlist ......................................................... 16
Turn Radio/GPS On/Off ........................................ 16
Informational Picture ................................................... 16
GPS Status ............................................................. 16
Radio Transmission Status .................................... 16
Mark Waypoint’s Indicators ................................... 17
ii
Using the Rino 110 Radio Features ...................... 18
Peer-to-Peer Positioning .............................................. 18
New Contact Page Overview ....................................... 18
Sending a Location ...................................................... 21
Map Page.................................................................22
Map Page Options ....................................................... 24
Using the Pan Map Option .......................................... 25
Programming the Data Fields ...................................... 26
Data Field Options ................................................. 26
Setting up the Map ....................................................... 27
General Setup ......................................................... 27
Tracks Setup ........................................................... 28
Map Features Setup................................................ 28
Text Setup .............................................................. 28
Map Data Setup...................................................... 28
Measuring Distance ..................................................... 28
Navigation Page ..................................................... 29
Using the Navigation Page .......................................... 29
Navigation Page Options ............................................. 31
Trip Computer Page ............................................... 32
Trip Computer Page Options ....................................... 32
Main Menu Page ..................................................... 33
Using the Main Menu .................................................. 33
Rino® 110 Owner’s Manual
INTRODUCTION > TABLE OF CONTENTS
Main Menu Options ..................................................... 34
Page Sequence Setup ............................................. 34
Shortcuts Menu ............................................................ 35
Waypoints ...............................................................36
Creating Waypoints ..................................................... 37
Projecting a Waypoint.................................................. 38
Editing a Waypoint ...................................................... 38
Find ‘N Go ............................................................... 40
Finding a Waypoint...................................................... 41
Finding a Contact......................................................... 43
Finding a City .............................................................. 44
Finding a Point of Interest ........................................... 45
Finding a Last Found Place ......................................... 47
Using a Goto ........................................................... 48
Route Page.............................................................. 49
Creating and Using a Route ......................................... 49
Editing a Route ............................................................ 50
Adding or Editing from the Route Map Page .............. 53
Navigating a Route ...................................................... 54
Stopping Navigation .................................................... 55
Data Fields for the Route Page .................................... 55
Data field options for Route Page: ......................... 55
Tracks Page ............................................................ 56
Rino® 110 Owner’s Manual
Using the TracBack Feature ........................................ 57
Setting up the Track Log ............................................. 58
Proximity Page ....................................................... 59
Satellite Page .......................................................... 60
Sky View graphic ................................................... 60
WAAS .......................................................................... 61
Satellite Strength .................................................... 61
Satellite Page Options .................................................. 62
Setup Pages ............................................................ 63
Time Setup Page .......................................................... 63
Units Setup Page .......................................................... 64
LORAN TD Format..................................................... 65
Display Setup Page ...................................................... 66
Heading Setup Page ..................................................... 67
Interface Setup Page .................................................... 68
System Setup Page....................................................... 70
Calendar .................................................................. 71
Alarm Clock ............................................................ 73
Calculator ................................................................ 74
Stopwatch ............................................................... 75
Stopwatch Lap Options ............................................... 75
Sun & Moon ............................................................ 76
Hunt & Fish ............................................................. 77
iii
INTRODUCTION > TABLE OF CONTENTS
Area Calculator ....................................................... 78
Games .....................................................................79
Memory Race .............................................................. 79
Waypoint Bomber ........................................................ 79
Clothesline ................................................................... 80
Assimilation ................................................................. 80
Specifications ......................................................... 81
Physical ........................................................................ 81
Performance ................................................................. 81
Radio ............................................................................ 82
Power ........................................................................... 82
Accessories ............................................................83
Transferring MapSource Data ............................... 84
What is FRS? .......................................................... 85
FRS Features................................................................ 85
FRS Limitations........................................................... 86
GMRS .......................................................................... 86
GPS Troubleshooting Guide ................................. 87
Radio Troubleshooting Guide ............................... 88
Frequency Charts ................................................... 89
Safety and Product Information ............................ 93
FCC Compliance Information ..................................... 93
FCC Licensing Information ......................................... 93
Limited Warranty ......................................................... 94
Software License Agreement ....................................... 96
Product Registration .................................................... 96
Contact Garmin............................................................ 96
Warnings and Cautions ................................................ 97
Index ...................................................................100
Appendix ..............................................................90
Data Field Definitions............................................. 90
Interface Information.............................................. 92
iv
Rino® 110 Owner’s Manual
GETTING STARTED > GETTING TO KNOW YOUR RINO 110
GETTING TO KNOW YOUR RINO 110
The Rino 110 (Radio Integrated with Navigation for
the Outdoors) is a 7.6 ounce, 12-channel, GPS-enabled
handheld device. It also has integrated radio functionality
to provide two-way communications for up to two miles
using 14 FRS (Family Radio Service) channels and
eight high-performance GMRS (General Mobile Radio
Service) channels. For more information about GMRS,
refer to the “Appendix.”
You can transmit your GPS position to other Rino
users on FRS and GMRS bands with the peer-topeer positioning feature. The Rino 110 stores up to
500 waypoints with a 10-character name and graphic
symbol. The active track log stores up to 2,048 points
and allows you to save up to 20 tracks with up to 125
points per track. Using MapSource® Points of Interest
(not included), the Rino 110 can display up to 1 MB of a
variety of different points (not actual maps), including
Rino® 110 Owner’s Manual
businesses, cities, landmarks, and marine points. Check
your local dealer or the Garmin Web site (www.garmin.
com) for a complete listing of MapSource products.
Garmin designed your Rino 110 with you, the user, in
mind. The Rino 110 is waterproof to IEC 60529 IPX7
standards and is rugged enough to endure the most trying
use. Garmin’s user-friendly interface allows you to start
navigating with your new GPS in no time. With your
Rino 110 you know where you are, where you’ve been,
and where you’re going. And since you’ll always know
the way back home, you can concentrate on what you set
out to do: explore the great outdoors.
1
GETTING STARTED > FRONT OF THE RINO 110
Front of the Rino 110
Power button:
• Press and hold to turn the unit On/Off
• Press to adjust contrast and backlighting
Call button:
• Press to send out Call Tone
• Sends position when released
(if enabled)
Talk button:
• Press and hold to talk
• Sends position when released
(if enabled)
Page/Quit button:
• Press to cycle through main pages
• Used to quit or escape menu items
Volume (V) button:
• Press to open volume control window
Speaker
2
LCD Display
Thumb Stick
• Press In to enter highlighted options and to
confirm messages
• Move Up, Down, Right or Left to move
through lists, highlight fields,
on-screen buttons, icons, enter
data, or move the map panning
arrow
• Press In and hold to display Shortcuts Menu.
Zoom/Map (Z) button:
• From the Map Page, press to open Zoom
control window
• From any other page, press to display Map
Page and press again to open Zoom control
Microphone:
• Hold unit 3–4 inches away when talking
Rino® 110 Owner’s Manual
GETTING STARTED > BACK OF THE RINO 110
Back of the Rino 110
2-way FRS/GMRS Antenna
Belt Clip Connector Mount
Headset Connector
with Weather cap
GPS Antenna
External Power And
Data Connector with
Weather cap
Battery Compartment D-Ring
Battery Compartment Cover
Mount Alignment Notches
Rino® 110 Owner’s Manual
3
GETTING STARTED > MAIN PAGE SEQUENCE
Main Page Sequence
All of the information you need to operate the Rino 110 can be found on five default main pages (or display screens).
Press and release the Page key to cycle through the Radio Page, Map Page, Navigation Page, Trip Computer, and Main
Menu Page. You can also access the Main Pages by pressing the on-screen Main Page button
. Customize the Main
Page sequence through the Main Menu (refer to the “Main Menu Page” section later in this guide).
Map Page
Radio Page
Main Menu
4
Navigation Page
Trip Computer
Rino® 110 Owner’s Manual
GETTING STARTED > OPERATING THE RINO 110
Operating the Rino 110
For best results, you should initialize the GPS receiver in
your Rino 110 unit before you use it the first time. Refer
to the “Initializing the Rino 110” section later in this
manual for instructions on initializing the unit.
The Rino 110 is programmed to provide “pop-up”
messages concerning operational characteristics and
conditions. Press the Thumb Stick In to acknowledge a
message and return to the current feature.
To use the Thumb Stick:
•
•
•
Press In to enter highlighted options and to
confirm messages
Move Up, Down, Right or Left to move through
lists, highlight fields, on-screen buttons, icons,
enter data, or move the map panning arrow
Press In and hold to display the Shortcuts Menu.
To use the page Option Menu:
2. Highlight the desired menu option and press the
Thumb Stick In to activate the option.
3. To close without making a selection, move the
Thumb Stick to the Right.
To lock/unlock the keys:
1. Press and hold the Thumb Stick In to access the
Shortcuts Menu. Highlight Enable Keylock and
press the Thumb Stick In. The Talk key is now
locked.
2. To unlock, press and hold the Page key until
“Keylock Disabled” is displayed (about 5 seconds).
Keylock Pop-up Message
1. Highlight the Option Menu on-screen button
at the top of the display screen and then press the
Thumb Stick In to open the menu.
Rino® 110 Owner’s Manual
5
GETTING STARTED > STATUS BAR OVERVIEW
Status Bar Overview
The Status Bar at the top of the screen displays on all
the available Main Pages. As you move around any of
the Main Pages, the current page’s title briefly displays
(3 seconds) and then is replaced by the Status Bar. The
current settings and operational icons on the Status Bar
are displayed as you use your Rino. The icons you may
see are shown and described below:
Option Menu button
Main Page Menu
button/ Exit button
Transmitting Radio signal
Backlight On
Radio On
Peer-To-Peer On/Location Ready to Send
Keylock On
Alarm Clock On
GPS On, Position Ready
GPS On, Position Not Ready
Status Bar
New batteries installed
Batteries are about 1/2 discharged
Batteries are fully discharged.
Install new batteries or recharge batteries.
Using External Power
Receiving Radio signal
6
Rino® 110 Owner’s Manual
UNIT OPERATION > RADIO PAGE
UNIT OPERATION
Radio Page
The Radio Page is the first of the default Main Pages.
This page provides the user interface for FRS (Family
Radio Service) and GMRS (General Mobile Radio
Service) radio operations. Garmin Rino units work
with 3rd party FRS/GMRS radios, provided the other
radios use standard FRS/GMRS frequencies. To take full
advantage of the Rino features, communicate with other
Rino users.
Also use the Radio Page to control and setup the radio,
view current settings, and see informational graphics of
the unit’s operation.
Initialization is automatic and should only take a few
minutes.
To initialize the unit (acquire satellites):
1. Take the Rino 110 outside where it has an
unobstructed view of the sky and turn it on.
2. The unit begins to search for satellite signals.
“Tracking Satellites” is displayed while the unit is
initializing.
3. Initialization should take no more than five
minutes. When the GPS is initialized and ready
for navigation, the message “3D Accuracy” is
displayed on the Radio Page.
Initializing the Rino 110
To take full advantage of all of the Rino 110 features,
the GPS receiver must be initialized. The initialization
process allows the Rino 110 to receive and store satellite
information and begin using the satellites for navigation.
Rino® 110 Owner’s Manual
Radio Page
7
UNIT OPERATION > RADIO PAGE
Using My ID and Symbol Fields
The My ID field allows you to enter a name and symbol
that appears on other Rino units as you communicate with
them. You may enter a name using a combination of up to
10 letters, numbers, or spaces. The Symbol field allows
you to choose a face icon (symbol) from a list to further
personalize your ID.
My ID Field
Symbol
3. To enter a new ID, use the Thumb Stick to move
the cursor to the desired character (letter, number,
or a space). Press the Thumb Stick In to select
that highlighted character. Choose Back to delete
the character to the left of the cursor. You may
enter up to 10 characters for your ID.
Entering a name
with the on-screen
keyboard
4. When you have entered your new ID, highlight OK
and press the Thumb Stick In.
To enter a name:
1. Using the Thumb Stick, highlight the My ID field.
Press the Thumb Stick In to activate the field and
display the keyboard.
2. Move the Thumb Stick Up, Down, Left, or Right
to highlight the Clear field, then press the Thumb
Stick In to clear the default Name ID.
8
Rino® 110 Owner’s Manual
UNIT OPERATION > RADIO PAGE
To change the user symbol:
1. Using the Thumb Stick, highlight the face symbol
to the right of the My ID field. Press the Thumb
Stick In to show a list of available face symbols
(icons).
2. Move the Thumb Stick Up or Down to scroll
through the selections. Because not all the
selections can fit in the window, a slider bar on the
right side indicates your current position in the list.
TIP: Hold the Thumb Stick Up or Down to scroll
through the list more quickly. Once you reach the
end of the list, you can “wrap” back to the top or
bottom by releasing the Thumb Stick then pressing
in the same direction again. This same method may
also be used on other selection windows.
3. Once you have highlighted the desired symbol,
press the Thumb Stick In.
Changing the user symbol
Rino® 110 Owner’s Manual
9
UNIT OPERATION > RADIO PAGE
Setting the Channel and Squelch Code
The Rino 110 has a total of 22 channels and 38 squelch
codes to select from using the Channel and Code
fields. Channels 1–14 are FRS channels and 15–22 are
GMRS channels (disabled by default in U.S. units). To
communicate with other Rino and FRS/GMRS users, you
must be on the same channel and squelch code. Garmin
Rino units work with 3rd party FRS/GMRS radios,
provided the other radios use standard FRS/GMRS
frequencies. A chart of Rino frequencies can be found in
the “Appendix.”
Squelch codes allow you to hear calls from only specific
persons. Thirty-eight (38) Squelch Codes (also called
Continuous Tone Coded Squelch System or CTCSS)
allow your Rino 110 to ignore unwanted calls from other
persons using the same channel. Be sure everyone you
will communicate with using your Rino has selected the
same squelch code (number).
10
Select from FRS 1–14 and GMRS
15–22 (with GMRS enabled)
NOTE: Squelch codes do not cause your conversation to be private. They only allow you to filter out
other users on the same channel, so you only hear
the radios you want to hear. Squelch Codes are not a
scrambling system!
Rino® 110 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Setting the squelch code to 0 (squelch code off) allows
you to hear all activity on the selected channel, but
you must be set to the same squelch code as the other
person(s) to transmit back. See the “Appendix” for a table
listing all of the 38 Squelch Codes and their frequencies.
As you change the main channels, the Rino 110
remembers the last channel/squelch code combination
that you were using. For example, you may set the unit
channel to 5 and squelch code to 21, then change the
main channel to 8 and squelch code to 2. If you change
the channel back to 5, the squelch code changes back to
its previous setting of 21. See the “Appendix” for more
information on FRS/GMRS and its operational aspects.
To change the Channel and/or Squelch Code:
2. Scroll through the selections and highlight the
desired selection. Because not all the items fit in
the window, a slider bar on the right side indicates
your current position in the list.
3. Once you have highlighted the desired selection,
press the Thumb Stick In.
Choose from 38 squelch codes. Setting the unit
to zero will allow you to hear all transmissions
on that channel, but you must be on the same
squelch code to communicate back.
1. Using the Thumb Stick, highlight the Channel
or Code field and then press In to show a list of
available channels/squelch codes.
Rino® 110 Owner’s Manual
11
UNIT OPERATION > RADIO PAGE
Scanning and Monitoring
The Scan option allows you to scan through the available
channels for voice activity. As the unit scans and
receives a signal (or if you transmit), it stops on that
channel/squelch code for a few seconds, then continues
scanning. When the Rino 110 is scanning and it receives
an incoming signal, the Rino 110 automatically decodes
the Squelch Code used by the incoming signal. The Rino
110 then uses that Squelch Code when it transmits back
to that unit.
The Code field is
blank when the unit is
scanning or monitoring
channels.
helps prevent the chances of missing a transmission.
The Scanlist also has Option Menu
choices to
Scan Current Codes or Scan All Codes. Choosing Scan
Current Codes scans only the Channel and Squelch Code
combinations in memory.
The Monitor option lets you listen to a single channel
for any activity, including static and weak voice signals.
The Rino series automatically squelches a frequency
to filter out unwanted noise. Using the Monitor option
temporarily turns off the automatic squelch, allowing
you to hear all activity on channel. If you see a broken
transmission symbol ( ), there is activity on your
selected channel, but the incoming signal does not match
the Squelch Code your unit is using.
You may use the Set Scanlist option to pick which
channels/squelch codes to scan. Scanning through the
all the channels can take time. Selecting only specific
channels/squelch codes decreases the scan time and
12
Rino® 110 Owner’s Manual
UNIT OPERATION > RADIO PAGE
To scan or monitor a channel(s):
1. Using the Thumb Stick, highlight the Scan or
Monitor button and then press In. Scan starts
searching through the available channels.
Monitor opens the channel to listen to any radio
transmissions on that channel.
2. To stop using either option, highlight the button
again and press the Thumb Stick In.
3. To begin scanning the codes you selected,
highlight the Option Menu
and press the
Thumb Stick In. Choose Scan Current Codes and
press the Thumb Stick In.
To setup a Scanlist:
1. Using the Thumb Stick, highlight the Option
Menu on-screen button
and press In.
Highlight Setup Scanlist and press the Thumb
Stick In.
2. To add/remove a channel from the list, highlight
the channel and press the Thumb Stick In to
add/remove the check mark in front of the name.
Only channels that are checked are scanned.
To select all channels or clear all channels, select
either the Select All or Clear All buttons and
press the Thumb Stick In.
Rino® 110 Owner’s Manual
Radio Page Option Menu
Scanlist Page
The Radio Page Option Menu provides the following:
Setup Radio, Setup Tones, Setup Scanlist, Turn Radio
Off/On, and Turn GPS Off/On. Refer to the following
pages for explanations of each item in the Radio Page
Option Menu.
13
UNIT OPERATION > RADIO PAGE
Radio Page Option Menu
The Radio Page Option Menu
allows you to
customize aspects of your Rino 110, such as setting up
the radio, programming call and ring tones, and setting up
a scanlist.
Setup Radio
The Setup Radio option displays the Radio Setup Page.
This page determines how the radio functions and enables
you to adjust the radio operation to your needs. The
following options are available:
Setup Radio Page
Send Location—enables/disables the peer-to-peer
positioning feature. See the “Peer-to-Peer” section for
more on this feature.
14
Allow Polling—allows you to enable/disable position
polling from other Rinos.
VOX Level—controls the sensitivity level of any
Voice Operated Transmission (VOX) accessory.
VOX accessories allow you to use the unit handsfree. A lower VOX setting is recommended for quiet
environments while a higher VOX setting should be
used in noisy environments. Setting the VOX level to 5
is recommended for most environments, but it may be
necessary to adjust the level to achieve the desired voice
trigger level. You will hear yourself talking in the headset
when transmitting successfully using VOX.
GMRS Radio—use this option to turn On/Off GMRS
channels 15–22 in U.S. units only. GMRS channels in
Canadian units are enabled automatically. See the “FCC
Licensing Information” section and the “Appendix” for
more information on using GMRS channels.
Rino® 110 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Headset Type—allows you to choose which accessory
headset or microphone you are using with the unit, or
have the unit automatically detect the type. If you use
more than one type of headset or microphone, you need
to set the unit to Ask When Detected before changing
accessories.
NOTE: If the headset has a PTT (Push to Talk)
button, it must be pressed for the unit to detect the
headset.
Roger Tone—when the Talk key is released, a tone is
sent to signify the end of the transmission. This option
allows you to choose one of four tones or set the tone to
Off.
Ring Tone—when an incoming transmission is received,
an attention tone sounds. This option allows you to
choose one of ten tones or set the tone to Off. The Ring
Tone will not sound again until there has been 45 seconds
of radio inactivity.
Microphone Sensitivity—allows you to set the
sensitivity of the internal microphone and the sensitivity
of a headset microphone.
Setup Tones
Call Tone—when the Call key is pressed, an attention
tone is transmitted. This option allows you to choose one
of ten tones.
Rino® 110 Owner’s Manual
Setup Tones Page
15
UNIT OPERATION > RADIO PAGE
Setup Scanlist
Refer to “Scanning and Monitoring” previously in this
manual for complete information about this feature and
the options in this page.
Turn Radio/GPS On/Off
Press the Thumb Stick In on either of these two options
to toggle them from on to off. For example, to turn GPS
Off, press the Thumb Stick In when Turn GPS Off is
highlighted.
Informational Picture
The Informational Picture on the bottom half of the
Radio Page features Garmin’s Mr. Mark Waypoint figure
showing current GPS and radio status, and radio actions.
As you operate the unit, the graphics change depending
on what actions you are taking and the unit settings.
GPS Status
Four satellites are shown on at the top of the picture along
with descriptive text to indicate GPS reception status.
As the unit collects satellite information, the satellite
16
symbols flash alternately until all four are steady to
indicate a 3D position fix. The more satellites that are
steady, the better your position fix.
Radio Transmission Status
As radio signals come in, signal wave symbols
( ) display to the left of Mark Waypoint. Fragmented
(or broken) signal symbols ( ) are shown to indicate
activity on that channel. Audio remains muted because
the incoming signal does not match the squelch code your
unit is set to.
Informational Picture showing
Mark Waypoint
Rino® 110 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Mark Waypoint’s Indicators
The Mark Waypoint figure displays several different icons, depending on what you are doing. See the illustrations for
more information.
GPS and FRS/GMRS Radio On;
Ready to transmit Position
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Transmitting on FRS
GPS and FRS/GMRS Radio On;
Position not ready;
Transmitting on GMRS
GPS and FRS/GMRS Radio On;
Position transmitted
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Receiving transmission
Rino® 110 Owner’s Manual
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Activity on channel;
Broken transmission.
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Position received from Rino user
GPS Off;
FRS/GMRS Radio On;
Position sending not available
GPS On;
FRS/GMRS Radio Off;
GPS operation only
17
UNIT OPERATION > USING THE RINO 110 RADIO FEATURES
Using the Rino 110 Radio Features
Your Rino 110 unit provides many features to enhance
your radio experience, such as transmitting locations and
receiving contact information. This section reviews some
of the advanced radio features.
Peer-to-Peer Positioning
The Rino 110’s most unique feature is being able to send
its location to another Rino, which is called Peer-to-Peer
positioning. With peer-to-peer positioning enabled (see
page 14) and a GPS position (see the “Initializing the
Rino 110” section), whenever you press and release either
the Call key or the Talk key, the Rino 110 automatically
sends out its location. This information is available to all
other Rino users that are monitoring the same channel
and squelch code. This feature allows you to track the
movement of other Rino users and even navigate to
their location. Locations may only be sent once every 30
seconds due to FCC restrictions. Your Rino 110 responds
to polling requests from other units more frequently.
18
To transmit your location to other Rino users:
1. Enable Send Location (see the “Setup Radio”
section).
2. Press and release either the Talk or Call key.
A flag on the top Status Bar or in Mark’s hand
indicates the unit is ready to transmit its position.
New Contact Page Overview
The first time that a signal is received from another Rino
user, the New Contact Page is displayed. From the New
Contact Page you can show their location on your Map,
Goto their location, or add them to your contact list
(select OK). Press Page to ignore this contact.
Name and Symbol
Contact
Information Field
New Contact Page
Rino® 110 Owner’s Manual
UNIT OPERATION > USING THE RINO 110 RADIO FEATURES
The Rino 110 can manage up to 50 contacts at any time.
Each time you receive a signal from a contact, your map
is updated showing their new position. A Track Log
of their movement is created and shown on your map
(see the “Track Logs” section). After a contact has been
established, a “<contact name> Updated” message briefly
appears at the bottom of your display each time the
contact updates.
All contacts are listed on the Contact List Page and also
displayed in the Contact Bar on the Map Page (see the
“Map Page” section). Contacts behave like waypoints
and count towards the 500 maximum waypoint total.
If the contact did not have a GPS location on the last
transmission, a ? (question mark) appears below the flag.
To view the contact details (such as Direction, Elevation,
Timestamp, Location, and Notes that have up to 30
characters), highlight the details field and press Left or
Right on the Thumb Stick to change to the next data
field.
Rino® 110 Owner’s Manual
Press Left or Right on the Thumb
Stick to view different contact data.
To accept a new contact:
1. When a new contact is received, the New Contact
Page automatically appears.
2. Highlight OK and press the Thumb Stick In. If you
do not select OK, the contact is not saved.
19
UNIT OPERATION > USING THE RINO 110 RADIO FEATURES
To review a contact and contact details:
1. From the Map Page, highlight the desired contact
on the Contact Bar and press the Thumb Stick In.
As you highlight the contacts on the Contact Bar,
the Map Page centers the map on that contact
and display its name, direction, and distance near
the top of the screen.
Or Press the Thumb Stick In and hold it until the
Shortcuts Menu is displayed. Highlight Find ‘N Go
and press the Thumb Stick In.
2. Highlight Contacts and press the Thumb
Stick In.
3. From the Contacts List, select the desired contact
and press the Thumb Stick In.
For Notes, highlight Edit and press In to start
entering data, up to 30 characters. For other
fields, highlight the field and press the Thumb
Stick In to start changing the data.
2. Highlight OK and press In when done.
To view a contact on the Map Page:
1. From the Contact Review Page, highlight Map and
press the Thumb Stick In.
2. Press the Page key when done to return to the
Contact Review Page.
Contact Bar
To change contact details:
1. The Elevation, Position, and Note fields may be
manually edited. Select the desired field and press
the Thumb Stick In.
20
Contacts also show on the Map
Page. Highlight the contact and the
map centers on their last position.
Rino® 110 Owner’s Manual
UNIT OPERATION > USING THE RINO 110 RADIO FEATURES
Sending a Location
Another handy feature is the ability to send a specific
location to other Rino users. This comes in handy when
you are trying to round up the group or you want to meet
at a specific location. You may send any point found from
the Find ‘N Go menu. If the unit needs to wait until 30
seconds have elapsed since the last position transmission,
a “Waiting to send location...” message appears until the
unit is able to transmit. If a location is sent more than
once, a number is automatically added to the end of the
name, such as CAMP, CAMP 1, and CAMP 2.
4. Depending on which category you select, highlight
the desired item and press the Thumb Stick In to
display the Information Page for that item.
5. From the Information Page, highlight the Option
Menu
in the upper right and press the Thumb
Stick In.
6. Highlight Send Location and press In again. The
unit now sends the point to the other Rino users
on your channel/squelch code.
To send a location:
1. Press the Thumb Stick In and hold it until the
Shortcuts Menu is displayed.
2. Highlight Find ‘N’ Go and press the Thumb
Stick In.
3. Highlight the desired category and press the
Thumb Stick In. (For the Contacts List, select the
desired contact and press the Thumb Stick In.)
Rino® 110 Owner’s Manual
Choose Send Location and press In.
21
UNIT OPERATION > MAP PAGE
Map Page
The Map Page displays your present position and
direction of movement using a triangular Position Icon
that is centered on the map. As you travel the map display
leaves a “trail” (track log) of your movements.
The map can display a higher level of detail than the
basemap provided with the unit (i.e. residential streets,
parks, etc.), if Garmin MapSource data has been loaded
into the unit using a CD-ROM mapping program. When
using MapSource data, the word “mapsource” displays
below the map scale whenever you zoom in to view map
details.
location to a point within the circle. The smaller the
circle, the more accurate your location.
When using the Pan Map feature, a small outline arrow
(Map Pointer)
can be moved about the page to
highlight and identify map items or to scroll the map to
view areas not shown on the display screen.
On the right side of the Map Page, you can choose to
show either the Contact Bar, Data Fields, or only the
Map. As you highlight the contacts on the Contact
Bar, the Map Page centers the map on that contact and
displays its name, direction, and distance.
In many instances the map displays an Accuracy Circle
surrounding the Position Icon. The Rino 110 uses both
map resolution and GPS accuracy in defining your
22
Rino® 110 Owner’s Manual
UNIT OPERATION > MAP PAGE
To view a Contact from the Map Page:
1. Highlight the desired Contact icon using the
Thumb Stick. As you highlight the contact on the
Contact Bar, the Map Page centers the map on
that contact and displays its name, direction, and
distance near the top of the screen.
2. Press the Thumb Stick In to view the details of
the Contact.
3. Press the Thumb Stick to the Left or Right to recenter the map on your current position.
The scale can be changed from 20 feet to 500 miles. A
lower zoom scale displays less area but more map detail,
while a higher zoom scale shows you a larger area with
less map detail. The Thumb Stick and Zoom (Z) key on
the front right of the unit allow you to zoom in and out on
the map. Press the Zoom (Z) key from any page (other
than the Map Page) to open the Map Page.
2. Use the Thumb Stick to change the map scale to
show more map area with less detail or less map
area with more detail.
Press and hold Up or Down on the Thumb Stick
to zoom the map scale rapidly. Press the Thumb
Stick Left, Right, or In to close the Zoom window.
The map scale in the lower left hand side of the display
is shown in the units of measurement selected in the
Units field of the Unit Setup Page (accessed through the
Main Menu Setup Page). If you zoom in so far that the
resolution of the map data is exceeded and the appearance
of the map is no longer accurate, the word, “overzoom”
displays just below the map scale.
To change scales on the Map Page:
1. Press the Zoom (Z) key to open the Zoom
window.
Rino® 110 Owner’s Manual
Press Up to Zoom Out;
press Down to Zoom In
23
UNIT OPERATION > MAP PAGE
Map Page Options
Map Page options allow a variety of operating and
custom features for your Rino 110. The Map Page options
are listed below. Highlight an option then press the
Thumb Stick In to select.
Map Page Option Menu
Pan Map—allows you to move the Panning Arrow (Map
Pointer) about on the map. Refer to the “Using the Pan
Map Option” section for complete instructions.
Stop Navigation—quits navigation of a Goto, Route,
or Track in progress. When you are not navigating to a
destination, the Stop Navigation option is “grayed out”
and is non-functional.
24
Show...—allows you to choose to show either the Contact
Bar, four programmable Data Fields, or show the Map
Only. Choosing either Contact Bar or Data Fields reduces
the map area.
Setup Map—displays the Setup Map Pages, which
allow you to tailor the map to your requirements such
as changing text size, map orientation, and map detail.
Refer to the “Setting up the Map” section for complete
instructions.
Measure Distance—displays the distance from one point
on the map to another.
Restore Defaults—returns the Map Page to the original
factory settings (defaults).
Rino® 110 Owner’s Manual
UNIT OPERATION > MAP PAGE
Using the Pan Map Option
The Map Page pan function allows you to display an
arrow used to point at and identify items on the map,
and to move the map in order to view areas beyond the
current viewing area on the display.
The map panning function is activated from the Option
Menu
on the Map Page. Use the Thumb Stick to
move the panning arrow (also referred to as the map
pointer) in the desired direction. If the arrow moves to
the edge of the map display, the map also moves to reveal
more area and a busy hourglass appears by the cursor
while the data is drawn on the screen.
Whenever you place the panning arrow on a map item,
the name of that item is highlighted. This feature applies
to waypoints, roads, lakes, rivers; nearly everything that
is displayed.
Press the Thumb Stick In to mark the arrow location or
display the map item Information Page. The Option Menu
allows you to send the location of that item, project
a waypoint from it, save it as a waypoint, set a proximity
Rino® 110 Owner’s Manual
circle around it, add it to a route, or view the Sun & Moon
or Hunt & Fish information for it. On-screen buttons at
the bottom of the page allow you to Goto the map item,
display it on the Map, or to select OK and return to the
Map Page. Press the Page key to stop panning the map.
To find an item near the map pointer:
1. When using the panning arrow, press and hold the
Thumb Stick In to display the Shortcuts Menu.
2. Select Find ‘N Go to display items. Select the
category you wish to search (waypoints, contacts,
etc.), then select Near Map Pointer from the popup list. The Rino 110 then searches for the items
nearest the location of the map pointer instead of
your actual location.
Map Page with
Panning Arrow
25
UNIT OPERATION > MAP PAGE
Programming the Data Fields
Select Show... Data Fields to view four optional
Data Fields on the right side of the screen that can be
programmed to provide a variety of travel and navigation
information. A list of the choices is shown to the right.
Not all data types are available on every page.
To program a data field:
1. Use the Thumb Stick to highlight the data field
and then press In to display the list of data
options.
2. Highlight the desired option and then press the
Thumb Stick In to change the data field.
Changing Data Fields
26
Data Field Options
Thee data field options apply to the data fields on the
Map Page, Navigation Page, and the Trip Computer. For
definitions of these data fields, refer to the “Appendix.”
Bearing
Course
Current Destination
Current Distance
Current ETA
Current ETE
Elevation
Final Destination
Final Distance
Final ETA
Final ETE
GPS Accuracy
Heading
Max Speed
Moving Avg. Speed
Odometer
Off Course
Overall Avg. Speed
Pointer
Speed
Sunrise
Sunset
Time of Day
To Course
Trip Odometer
Trip Time—Movg.
Trip Time—Stopped
Trip Time—Total
Turn
Velocity Made Good
Vertical Speed
Trip Computer Only Location (lat/lon)
Location (selected)
Rino® 110 Owner’s Manual
UNIT OPERATION > MAP PAGE
Setting up the Map
Setup Map displays the five Map Setup Pages, each
accessed by an on-screen button.
Setup Items
Options
Sub-Page Buttons
General Setup
Lines Setup
Points Setup
Text Setup
Map Data Setup
To use Map Setup options:
1. Select Setup Map from the Option Menu
and
then press the Thumb Stick In to display the Map
Setup Page.
2. Press Up or Down on the Thumb Stick to
highlight the desired sub-page button, which
displays the options list for that sub-page to
the left.
3. Press Left, then Up or Down on the Thumb Stick
to highlight an item on the list.
Rino® 110 Owner’s Manual
Press Right to return to the sub-page buttons.
4. Use the Thumb Stick to highlight the desired
option and press In to activate.
5. Press the Page key or the on-screen X button to
return to the Map Page.
General Setup
Orientation—Track Up or North Up; fixes the top of
the map display to the current track heading or to a north
heading.
Auto Zoom—On or Off; automatically scales the map to
display both your current location and the next point to
which you are navigating.
Detail—Most, More, Normal, Less, or Least; controls
how much map detail you see. This setting only applies
to a map feature set to Auto. Those features which have
a specified scale or are turned Off are unaffected by this
setting.
Display Mode—Land or Water.
27
UNIT OPERATION > MAP PAGE
Tracks Setup
Saved Tracks and Track Log—scale options; Off, Auto,
or 20 ft.–500 miles, sets the maximum scale at which the
feature should appear on the screen. Some types of data
display only at certain zoom scales.
Goto Line—Bearing or Course.
Map Features Setup
Points of Interest and Waypoints—Off, Auto, or 20
feet to 500 miles, sets the maximum scale at which that
feature should appear on the screen. Some types of data
display only at certain zoom scales.
Text Setup
Points of Interest and Waypoints—None, Small,
Medium, or Large; control the screen size of the name.
Map Data Setup
Show—check box; check mark determines if map data is
used or not. Option Menu allows you to choose to show
all, show none, or show specific MapSource data.
28
Measuring Distance
To use the Measure Distance option:
1. Select Measure Distance from the Option Menu
and then press the Thumb Stick In to display
the Panning Arrow. Ref displays under the arrow.
2. Use the Thumb Stick to move about on the Map
Page until you reach the point to which you want
to measure. A new Map Pointer field displays
showing the location of the pointer and the
direction and distance from where you began the
measuring.
3. To begin measuring from a different point, press
the Thumb Stick In at the desired location.
4. To stop measuring, press the Page key.
Map Pointer Field
Measuring Distance
Rino® 110 Owner’s Manual
UNIT OPERATION > NAVIGATION PAGE
Navigation Page
The Navigation Page provides active guidance with a
rotating compass ring that shows your course (track)
while you are moving and a bearing pointer to indicate
the current direction to your destination (bearing) relative
to the course.
The Data Field at the top of the page, by default shows
you the name of your destination. All five Data Fields can
be programmed to display a variety of navigation data.
The list of data field choices can be found in the “Map
Page” section listed in the “Data Field Options” heading
and definitions may be found in the “Appendix.”
When you are moving, the heading of the Compass Ring
is controlled by the GPS receiver (based upon settings
customized in the Heading Setup Page).
Rino® 110 Owner’s Manual
Straight Line
Distance to
Destination
Destination Name
(Waypoint)
Times to
Destination
Bearing
Pointer
Compass Ring
Selectable
Data Fields
Using the Navigation Page
The two main components of the Navigation Page are the
Bearing Pointer and Compass Ring. The Bearing Pointer
always points directly to the destination, no matter what
your current location might be. The Compass Ring
displays your heading.
29
UNIT OPERATION > NAVIGATION PAGE
While you are navigating a route, the pointer indicates the
direction (a bent arrow) of the turn to the next point in the
route as well as the direction to the current point when
you get within 15 seconds Estimated Time of Arrival of
the current point.
For example, if the arrow is pointing straight up, you
are going directly to your destination. If it points any
direction other than up, turn and move towards the
direction the arrow is pointing until it points up, and
then continue in that direction. If you are using the
Course Pointer option instead and you drift away from
the original line of travel to your destination, the Course
Deviation Indicator (CDI) provides graphic indication of
drift (right or left) and displays the distance off course.
When you are not on an active Goto, Track, or Route
(in other words, you are not traveling to a recorded
destination), the window at the top of the page is blank
when Destination is selected. The Compass Ring
displays your heading while you are moving, but the
data fields to the right of the page will not display any
30
destination related data, such as the Estimated Time of
Arrival.
CDI Scale
Navigation Page with Course
Pointer and Course Deviation
Indicator (CDI) Scale active.
To stop navigating:
1. Highlight the on-screen Option Menu
button
at the top of the Navigation or Map Page and
press the Thumb Stick.
2. Select Stop Navigation, then press the
Thumb Stick.
Rino® 110 Owner’s Manual
UNIT OPERATION > NAVIGATION PAGE
Navigation Page Options
Stop Navigation—cancels navigation. “Grayed out” or
disabled unless you are navigating on a Goto, Track, or
Route.
Bearing Pointer/Course Pointer—toggles between
Bearing (always directed at destination) and Course
(distinctive with dots across center of compass ring,
shows amount of correction needed to be back on
course.). Refer to the image on the previous page for an
example of the compass with the Course Pointer. Refer
to the image below for an example of a compass with a
Bearing Pointer.
Show Data Fields/Big Compass—toggles to display data
fields on the right side of the display or removing the data
fields and showing a larger compass.
Rino® 110 Owner’s Manual
Restore Defaults—returns options and data field choices
to factory designations.
Navigation Page Option Menu
To change data fields:
1. Use the Thumb Stick to highlight the desired data
field and then press it In to display the list of data
options.
2. Select the desired option from the list and press
the Thumb Stick In. The list of data field choices
may be found on page 26 and definitions may be
found in the “Appendix.”
31
UNIT OPERATION > TRIP COMPUTER PAGE
Trip Computer Page
The Trip Computer Page by default displays up to seven
different types of navigation data. Choose Big Numbers
to display two (2) large data fields.
By selecting the information options that you prefer
and arranging them in a desired order on the page, you
can customize the Trip Computer Page to meet your
navigation needs.
Trip Computer Page Options
The Option Menu allows you to reset the Trip Computer
data when you are ready to start a new trip, choose
between Big or Small Numbers, and Restore Defaults.
Trip Computer Page,
Small Numbers
Trip Computer Page,
Big Numbers
Each data field is selectable and can contain one of many
data information options. The default settings for these
fields are shown in the top-right image. The list of data
field choices may be found on page 26 and definitions
may be found in the “Appendix.” When the data field title
is selected, press the Thumb Stick In to select a new data
field choice.
Reset—clears recorded data from the page to begin
recording new data.
Big/Small Numbers—changes the display from seven
small data fields to two large data fields.
Restore Defaults—returns the Trip Computer Page to the
original factory settings (defaults).
Selecting a data field
32
Rino® 110 Owner’s Manual
UNIT OPERATION > MAIN MENU PAGE
Main Menu Page
The Main Menu provides access to
additional Rino 110 feature pages.
The pages listed below provide
enhancements to Rino 110 operation.
Press the Page key repeatedly to
cycle to the Main Menu or select it
Main Menu Page
from the Main Page Menu at the top
of each main page.
Using the Main Menu
The Main Menu allows access to many features and
pages in the Rino 110. Please refer to the “Features”
section for a complete description of the items accessed
through the Main Menu.
Mark Waypoint Page—allows you to mark and store
a waypoint for your current location or a map pointer
location.
Points of Interest, Addresses, and Intersections. (Some
require MapSource data.)
Routes Page—allows you to create and store routes for
repeated use.
Tracks Page—provides access to the track log, saved
tracks, and contact tracks.
Proximity Page—allows you to set a proximity alert
distance around contacts or waypoints.
Satellite Page—provides a picture of the satellite signal
tracking and tells you when the unit is ready to navigate.
Setup Page—allows tailoring of items such as time
format, units of measure, display backlighting timeout
and contrast adjustment, heading selection, interface
setups, and system software information.
Calendar Page—provides you with a monthly calendar
with programmable reference notes.
Find ‘N Go Menu—allows you to locate and Goto
Waypoints, Favorite Locations, Cities, Interstate Exits,
Rino® 110 Owner’s Manual
33
UNIT OPERATION > MAIN MENU PAGE
Alarm Clock—provides a settable 24-hour alarm clock.
Main Menu Options
Calculator—provides a calculator feature available in
two forms: Standard or Scientific.
Through the Main Menu you can establish the sequence
of pages.
Stopwatch Page—allows you to use the unit as a
stopwatch, including a lap timer.
Page Sequence Setup
You may add, remove, or reorder any of the Main Pages,
plus additional pages. The default Main pages are Radio,
Map, Navigation, Trip Computer, and Main Menu. The
Main Menu cannot be removed from the page sequence.
If a page is added to the Main Page Sequence, it does not
appear in the Main Menu.
Sun & Moon Page—shows a graphic display of both
the Sun & Moon locations at various times, dates, and
locations.
Hunt & Fish Page—provides you with a listing of best
times for hunting and fishing for a chosen location.
Area Calculation Page—use this function to calculate
area as you move around.
Games Page—games are provided as an entertainment
feature.
Many of the items in the Main Menu Page are discussed
in-depth in the “Features” section. Refer to the specific
section for more information.
34
To move, insert, or remove a Main Page:
1. From the Main Menu, highlight the Option Menu
on-screen button
and press the Thumb Stick
In. Highlight Page Sequence Setup and press In.
2. To move a page in the page sequence, highlight
the page and press In. Select Move then move
the Menu item Up or Down using the Thumb
Stick. When the desired position is displayed and
press the Thumb Stick In.
Rino® 110 Owner’s Manual
UNIT OPERATION > MAIN MENU PAGE
To insert a new page, highlight the page you wish
to insert it before and press In. Select Insert, then
choose a page from the list and press the Thumb
Stick In.
To remove a page in the order, highlight the page
and press In. Select Remove and press the
Thumb Stick In.
Inserting a new page in
the Page Sequence
Shortcuts Menu
The Shortcuts Menu is accessed by pressing the Thumb
Stick In until the menu pops up on the middle of the
display. The Shortcuts Menu can be accessed from most
pages.
Rino® 110 Owner’s Manual
Shortcuts Menu
Mark Waypoint—marks your current location as a
waypoint. Opens the Mark Waypoint Page that allows
you to customize the waypoint information as well as
Goto or show on the Map.
Find ‘N Go—opens the Find ‘N Go Page. From the Find
‘N Go Page, you can find waypoints, contacts, and cities.
You may also find Points of Interest if MapSource data is
loaded into the Rino 110.
Enable Keylock—enables keylock so keys are not
inadvertently pushed. Press and hold the Page key to
unlock the keys.
35
UNIT OPERATION > WAYPOINTS
Waypoints
There are numerous ways to create, edit, and use
waypoints. The Mark Waypoint Page and the Find ‘N Go
Menu are two common pages for creating and editing
waypoint. You can also create a waypoint using the Map
Page. The Rino 110 holds up to 500 waypoints.
The Mark Waypoint Page allows you to mark and record
any location as a waypoint and appears with a graphic
name block that displays the assigned number for that
waypoint and a waypoint symbol.
To mark your current location and open the
Mark Waypoint Page:
1. Press and hold the Thumb Stick In until the
Shortcuts Menu opens.
2. Highlight Mark Waypoint and press the Thumb
Stick In. The Mark Waypoint Page opens. You
can also access this page by highlighting Mark
on the Main Menu Page and pressing the Thumb
Stick In.
36
3. To save the waypoint, highlight OK and press the
Thumb Stick In. If you do not want to save it as a
new waypoint, press the Page key to cancel.
Waypoint
Name
Symbol
Waypoint
Details
Mark Waypoint Page
To change Mark Waypoint Page Options:
•
•
•
To change the name of the waypoint, use the
Thumb Stick to highlight the waypoint name field.
To assign an identifying symbol to a waypoint, use
the Thumb Stick to highlight the symbol block just
above the waypoint name.
To view the waypoint details, highlight the details
field and press Left or Right on the Thumb Stick
to change to the next data field.
Rino® 110 Owner’s Manual
UNIT OPERATION > WAYPOINTS
Creating Waypoints
There are many ways to create a waypoint. You can use
any of the methods listed below.
To create a waypoint for a map feature:
1. With the Pan Map feature active, move the
panning arrow (map pointer) to the map item you
want and highlight it.
2. Press In and release the Thumb Stick to display
the item Information Page.
3. With the Information Page displayed, highlight the
Option Menu button
at the top of the page
and then press the Thumb Stick to open.
4. Highlight Save As Waypoint and press the
Thumb Stick to save the item as a waypoint.
Saving a map feature as a waypoint
Rino® 110 Owner’s Manual
To create a waypoint using the panning
arrow:
1. With the Pan Map feature active, move the
panning arrow (map pointer) on the map to the
location you want to mark, then press the Thumb
Stick.
2. The Mark Waypoint Page displays, automatically
assigning a number to the waypoint.
To create a waypoint by manually entering its
coordinates (lat/lon):
1. Press In and hold the Thumb Stick to access the
Shortcuts Menu. Highlight Mark Waypoint and
press In. You can also use the Find ‘N Go to view
a previous waypoint.
2. Highlight the details field and press Left or Right
on the Thumb Stick to change to the Location
field. Press In and enter the new coordinates
using the on-screen numerical keyboard. Highlight
and press OK when finished.
3. You may also change the waypoint name and/or
symbol or add notes.
37
UNIT OPERATION > WAYPOINTS
Projecting a Waypoint
Editing a Waypoint
To project a waypoint:
To edit a waypoint:
Projecting a waypoint from any map item (another
waypoint, etc.) allows you to establish a new waypoint on
a bearing and distance projected from that map item.
1. Select a map item from the Find ‘N Go Menu.
2. Highlight the Option Menu on-screen button
at the top of the Information Page and press the
Thumb Stick In to display the options. Highlight
Project Waypoint and press In.
3. Highlight either the bearing or distance field, then
press the Thumb Stick In to display the numerical
keyboard. Enter the new bearing or distance, then
highlight OK and press In to finish.
A waypoint or contact can be edited to add notes or
change the map symbol, name, coordinates, or elevation.
You can also delete a waypoint or contact.
1. Use the Find ‘N Go Menu to display the waypoint/
contact or highlight it on the Map Page and press
the Thumb Stick In.
2. To make changes to the waypoint map symbol,
name, location coordinates, elevation fields and
notes, highlight the desired field and press the
Thumb Stick In to display the keyboard. (For
Notes, highlight Edit and press In to start entering
data, up to 30 characters.) Select OK and press
the Thumb Stick In to finish.
3. Highlight the OK button the press the Thumb
Stick to save the changes.
Project Waypoint Page
38
Rino® 110 Owner’s Manual
UNIT OPERATION > WAYPOINTS
To delete a waypoint or contact:
1. Use the Find ‘N Go feature to display the point.
2. Highlight the Delete button and then press the
Thumb Stick In. Confirm the deletion.
4. Use the panning arrow to drag the waypoint to the
new location and then press the Thumb Stick In
to place it.
Press the Page key before pressing the Thumb
Stick to cancel moving the waypoint and return to
the Main Pages.
To save Map or Find ‘N Go items as
waypoints:
Deleting a waypoint
To move a waypoint by dragging it:
1. Use the Find ‘N Go Menu to display the Waypoint
Page for the waypoint you want to move.
2. Highlight and press the Map on-screen button to
display the waypoint on the map.
3. With the waypoint highlighted by the panning
arrow, press In and release the Thumb Stick. The
word “Move” displays beneath the panning arrow.
Rino® 110 Owner’s Manual
1. Access the Information Page for the desired item
(highlighted from the map or selected from the
Find ‘N Go Menu).
2. Open the Option Menu at the top of the page,
select Save As Waypoint.
3. Press the Thumb Stick In to save the item to the
Waypoints List.
4. Highlight Save As Waypoint and press the
Thumb Stick In.
39
UNIT OPERATION > FIND 'N GO
Find ‘N Go
The Find ‘N Go Menu allows you to find stored locations
(waypoints) and cities. They can be found by name or
by those nearest to your current location. If you are
using certain MapSource data, the list of find locations is
expanded to include Points of Interest. If you would like
to use an option that is grayed out (disabled), you need to
load detailed maps using MapSource.
To access the Find ‘N Go Menu:
1. Press and hold the Thumb Stick In to access the
Shortcuts Menu.
2. Highlight Find ‘N Go and press In.
Or
1. Press the Page key or the on-screen Main Page
Menu button to display the Main Menu.
2. Highlight the Find ‘N Go icon and press the
Thumb Stick In.
40
Find ‘N Go Menu
Categories are listed in two different ways: By Name and
Nearest. The By Name list contains every item in the map
database for the selected category, while the Nearest list
contains only those items that are near to your Current
Location or the Map Pointer.
These pages are structured with a set of sub-menus and
location information pages that guide you through the
process of finding locations.
Rino® 110 Owner’s Manual
UNIT OPERATION > FIND 'N GO
Finding a Waypoint
Waypoints that you have created and stored in the Rino
110 can be found by selecting the Waypoint option from
the Find ‘N Go Menu. You can find a waypoint from the
list of waypoints using the By Name or Nearest options
as explained on the previous page. When selected
from the list, the waypoint displays on the Waypoint
Information Page.
The Waypoint Information Page displays the waypoint
name or number, a map symbol, the location in lat/lon,
elevation, distance, bearing, and three on-screen buttons
for Goto, Map, and OK functions.
To find a waypoint by nearest:
1. Use the Thumb Stick to select Waypoint from the
Find ‘N Go Menu. Press the Thumb Stick In to
select Nearest from the pop-up menu. Press the
Thumb Stick In to display the Waypoints List.
2. Use the Thumb Stick to select the desired
waypoint from the list and then press the Thumb
Stick In to display the Information Page for that
waypoint.
3. With the Information Page displayed, select Goto
to create a direct line of travel to the waypoint.
Select Map to view the waypoint location on the
map, or select Delete to delete the waypoint.
4. Press the Option Menu button
to access
additional features. You can select: Send Location
(to other Rino users), Project Waypoint, Set
Proximity (alarm), Add to Route, View Sun & Moon
(reports for that waypoint), View Hunt & Fish
(reports for that waypoint), or Reposition Here.
Nearest Waypoints selected
in Find ‘N Go Menu
Rino® 110 Owner’s Manual
41
UNIT OPERATION > FIND 'N GO
To find a waypoint by name:
1. Use the Thumb Stick to select Waypoint from the
Find ‘N Go Menu. Press the Thumb Stick In to
select By Name from the pop-up menu. Press the
Thumb Stick In to display the Waypoints List.
Find ‘N Go Menu
2. Use the Thumb Stick to enter the name of the
waypoint that you would like to find.
3. Select OK when you are finished entering the
name. The waypoint list opens with the name
closest to the name you entered on the top.
4. Select the desired waypoint from the list and
then press the Thumb Stick In to display the
Information Page for that waypoint.
5. With the Information Page displayed, select Goto
to create a direct line of travel to the waypoint.
Select Map to view the waypoint location on the
map or select Delete to delete the waypoint.
6. Press the Option Menu button
to access
additional features. You can select: Send Location
(to other Rino users), Project Waypoint, Set
Proximity (alarm), Add to Route, View Sun & Moon
(reports for that waypoint), View Hunt & Fish
(reports for that waypoint), or Reposition Here.
Entering a waypoint
name to find By Name
42
Rino® 110 Owner’s Manual
UNIT OPERATION > FIND 'N GO
Finding a Contact
Contacts that you have received in the Rino 110 can be
found by selecting the Contacts option from the Find ‘N
Go Menu.
Contact List
To find a contact:
1. From the Find ‘N Go Menu, highlight Contacts
and press the Thumb Stick In.
2. From the Contacts List, select the desired contact
and press the Thumb Stick In.
3. With the Contact Information Page displayed,
select Goto to create a direct line of travel to the
contact. Select Map to view the contact’s location
on the map, or select Delete to delete the contact.
Rino® 110 Owner’s Manual
If the contact did not have a GPS location on the
last transmission, a question (?) mark appears
below the flag. To view the contact details,
highlight the details field and press Left or Right
on the Thumb Stick to change to the next data
field.
Contact Information Page
4. Press the Option Menu button
to access
additional features. You can select: Poll location,
Send Location (to other Rino users), View Track,
Project Waypoint, Save as a waypoint, or Set
Proximity (alarm).
43
UNIT OPERATION > FIND 'N GO
Finding a City
Cities can be found by selecting the Cities option of
the Find ‘N Go Menu, selecting the city from the list
of Nearest or By Name, and then displaying the City
Information Page.
The City Information for the selected city displays,
including the city name, the size by population, and
distance from your location. You can view it on the map
or create a Goto direct route to the city from your current
location or from a location defined by the panning arrow
(map pointer). You can also save the city as a waypoint or
add it to an existing route.
To find a city:
1. Use the Thumb Stick to select the Cities option,
then press it In to display the find Nearest or find
By Name prompt. Selecting By Name displays
the keyboard as an alternative scrolling through
the list of nearest cities. If you are currently
panning the map, the option Near Map Pointer
appears in place of the Nearest option.
44
2. If using find By Name, begin spelling the name
of the city by using the keyboard. When you have
entered enough characters to define the name,
a match list displays. If you are using find By
Nearest or Near Map Pointer scroll through the
list to find the city you want. Use the Thumb Stick
to select the desired city from the list and then
press it In to display the Information Page for
that city.
3. With the Information Page displayed, you can
select Goto, Map, or OK options.
4. Press the Option Menu button
to access
additional features. You can select: Send Location
(to other Rino users), Project Waypoint, Save as
a Waypoint, Set Proximity (alarm), Add to Route,
View Sun & Moon (reports for that waypoint), or
View Hunt & Fish (reports for that waypoint).
Rino® 110 Owner’s Manual
UNIT OPERATION > FIND 'N GO
Finding a Point of Interest
You can use the Find Points of Interest option to
locate a nearby restaurant, lodging, landmark, public
building, park, etc. However, you must have transferred
a MapSource Points of Interest (POI) to the unit map
database. Otherwise, this option is grayed out and not
functional. Here is a list of Point of Interest categories:
• Food & Drink
• Services
• Lodging
• Transportation
• Attractions
• Emergency & Govt.
• Entertainment
• Manmade Places
• Shopping
In many instances, these categories are subdivided into
types, such as in the instance of Food & Drink. When you
select Food & Drink from the list of categories, you are
then presented with a list of types that includes All Types
and cuisine options such as American, Asian, Barbecue,
and Chinese.
Rino® 110 Owner’s Manual
Food & Drink types
Once you have selected an item, you can display the
Information Page for that item. You can then use the onscreen buttons to Goto or view the location on the Map;
or use the Option Menu
for more choices.
45
UNIT OPERATION > FIND 'N GO
To find a point of interest:
1. Use the Thumb Stick to highlight Points of
Interest and then press it In to display the Points
of Interest Categories List.
2. Use the Thumb Stick to select the desired
category and then press it In to display the
Types List.
If necessary, use the Thumb Stick to select the
desired type and then press it In to display the list
for that type.
3. Use the Option Menu
at the top of page to
select from either By Name or Nearest options.
Selecting By Name displays a keyboard allowing
you to enter the characters of the name you want.
A list of matches displays when enough characters
are entered.
4. Use the Thumb Stick to highlight your selection
from the list and then press it In to display the
Information Page for that item.
5. Use the on-screen buttons to Goto or view on the
Map, or use the page Option Menu.
46
Nearest Food & Drink
6. Press the Option Menu button
to access
additional features. You can select: Send Location
(to other Rino users), Project Waypoint, Save as
a Waypoint, Set Proximity (alarm), Add to Route,
View Sun & Moon (reports for that waypoint), or
View Hunt & Fish (reports for that waypoint).
Rino® 110 Owner’s Manual
UNIT OPERATION > FIND 'N GO
Finding a Last Found Place
You can use the Recently Found Places option to
locate Points of Interest, Cities, Waypoints or Contacts,
Intersections, and other locations you have recently
retrieved. The process for finding recent points from the
Find ‘N Go list is the same as finding a regular waypoint.
To find a Last Found Place:
1. Use the Thumb Stick to select the Last Found
Places option from the Find ‘N Go List and then
press it In.
Sub-page
buttons
Last Found Places Page
Rino® 110 Owner’s Manual
2. Press Up or Down on the Thumb Stick to
highlight the desired sub-page button, which
will display the options list for that sub-page
(Points of Interest, Cities, Waypoints/Contacts, or
Intersections) to the left.
3. Press Left then Up or Down on the Thumb Stick
to highlight an item on the list and press the
Thumb Stick In to display the Information Page
for that item. Press Right to return to the sub-page
buttons.
4. With the Information Page displayed, you can
select Goto to create a direct line of travel to the
item. Select Map to view the waypoint location or
select OK. For Waypoints and Contacts, you may
also choose to Delete to permanently remove
that item.
5. Use the page Option Menu to send the location of
that point, project a new waypoint from its location,
set a proximity circle, add the item to an existing
route, or view sun/moon or hunt/fish position data
for this time and date.
47
UNIT OPERATION > USING A GOTO
Using a Goto
The Goto function allows you to create a direct route to a
destination (waypoint, city, or point of interest). Once you
have accessed the Information Page for an item, use the
Goto button at the bottom of the page to initiate travel,
using the Map and Navigation Pages for guidance.
To activate a Goto:
1. Use the Find ‘N Go Menu to access the
Information Page for any desired destination and
use the Thumb Stick to highlight the Goto button.
2. Press the Thumb Stick In to start navigation.
3. Observe the Navigation Page: it displays the
name of your destination, the distance from your
current location, and a Bearing Pointer indicating
the direction you should travel. The time required
to reach your destination displays when you
begin to travel and establish a predictable rate of
movement. The Data Fields to the right of the
page display information relative to your travel.
4. Use the Page key or Main Page Menu to access
the Map Page and observe your movements and
a dark line indicating the direct path from your
current location to your destination.
5. Use the Bearing Pointer on the Navigation Page
to maintain travel in the right direction and observe
distance and time information to monitor your
progress.
When you are close to your destination, an “Arriving
at Destination” message appears. If you move past the
destination, the Bearing Pointer reverses and the distance
increases.
To stop navigation, select the on-screen Option Menu
button
at the top of the Navigation or Map Page.
Select Stop Navigation, then press the Thumb Stick In.
Viewing a Goto on the Map Page
48
Rino® 110 Owner’s Manual
UNIT OPERATION > ROUTE PAGE
Route Page
Route navigation allows you to create a sequence of
intermediate waypoints that leads you to your final
destination. The Rino 110 stores 20 routes, each with up
to 50 waypoints. A route can be created and modified
from the Route Page, and waypoints can be added to a
route from the Find ‘N Go Menu. More complex routes
can be created using a PC and MapSource mapping
programs and then transferred to the unit’s memory.
Creating and Using a Route
Create a route from the Routes Page. You can then use
that route to get to your destination.
To create a route:
1. Access the Routes Page from the Main Menu. The
page has a New button, a list of routes, and the
number of unused routes.
2. Use the Thumb Stick to highlight the New button
and press it In to display the route Setup Page.
Rino® 110 Owner’s Manual
Routes List Page
3. With an empty row (dashed) in the route list
highlighted, press the Thumb Stick In to display
the Find ‘N Go Menu.
4. Select a route waypoint from one of the Find ‘N
Go Menu categories and display the Information
Page for the selected waypoint, city, exit, point of
interest, etc. Highlight the on-screen Use button
and press the Thumb Stick In to place it on
the route.
5. To add more waypoints to the route, repeat the
process in Steps 3 and 4. The route is named for
the first and last waypoints on the route.
You can add waypoints to the end of an existing route at
any time by using the Find ‘N Go Menu.
49
UNIT OPERATION > ROUTE PAGE
To add a Find ‘N Go Menu item to a route:
1. Select an item from the Find ‘N Go Menu and
display its Information Page. If a contact is used
in a route, the route changes as the contact’s
position is updated, or it may be saved as a
Waypoint to serve as a stationary point.
2. Select the page Option Menu and select Add To
Route to display the list of routes.
3. Highlight and select the route desired and then
press the Thumb Stick In. A “Waypoint Added
Successfully” message displays.
Editing a Route
To remove all waypoints:
1. From the Route Page, select the on-screen
Option Menu button
and press the Thumb
Stick In to access the Option Menu.
2. Highlight the Remove All option and then press
the Thumb Stick In to remove all waypoints from
the list. When you see the prompt “Do you really
want to remove all waypoints from the route?”,
select Yes.
50
Route Options
To reverse the route:
1. From the Route Page, select the on-screen page
Option Menu button
and press the Thumb
Stick In to access the Option Menu.
2. Highlight the Reverse Route option and then
press the Thumb Stick In to reverse the order of
waypoints in the list. To change the route back to
the original order, repeat this process.
Rino® 110 Owner’s Manual
UNIT OPERATION > ROUTE PAGE
To copy the route:
1. From the Route Page, select the on-screen page
Option Menu button
and press the Thumb
Stick In to access the Option Menu.
2. Highlight the Copy Route option and then press
the Thumb Stick In to copy. The copied route
displays on the Route Page and is named the
same but followed by the numeral 1 (one). You
may then rename and/or modify the copied route.
To delete the route:
1. From the Route Page, select the on-screen page
Option Menu button
and press the Thumb
Stick In to access the Option Menu.
2. Select Delete and then press the Thumb Stick In.
When you see the prompt “Do you really want to
delete route?”, select Yes.
To restore default settings for the route:
1. From the Route Page, select the on-screen page
Option Menu button
and press the Thumb
Stick In to access the Option Menu.
Rino® 110 Owner’s Manual
2. Select Restore Defaults and then press the
Thumb Stick In to restore factory settings.
To review a route point:
1. Select the point from the Route Points List and
press the Thumb Stick In to access the Option
Menu for the waypoint.
2. Highlight Review and then press the Thumb
Stick In to display the Information Page.
3. Highlight the on-screen OK button and then press
the Thumb Stick In to return to the Route
Points List.
To insert a new point on the route list:
1. Select the row where you want the new point
inserted before. Press the Thumb Stick In.
2. Highlight Insert and press the Thumb Stick In
to display the Find ‘N Go Menu and select a new
waypoint, city, exit, point of interest, etc.
51
UNIT OPERATION > ROUTE PAGE
Route point review options
3. With the new point highlighted, press the Thumb
Stick In to display the Information Page for the
new point and then select the on-screen OK
button to add it the route.
To remove a point from the route list:
1. Select the point that you want to remove from the
Route Points List and press the Thumb Stick In.
2. Highlight Remove and press the Thumb Stick In
to remove the waypoint from the list.
2. Highlight Change and press the Thumb Stick In
to display the Find ‘N Go Menu or create a new
waypoint and add it to the points list.
3. Select a new waypoint, access its Information
Page and press the on-screen Use button to
replace the old route waypoint.
To move a route point:
1. Select the point from the Route Points List and
press the Thumb Stick In.
2. Highlight the Move option and press the Thumb
Stick In to select the waypoint.
3. Use the Thumb Stick to move the point up or
down in the list. Press the Thumb Stick In to
leave the waypoint in the new list order.
To change a route point:
1. Select the waypoint that you want to change from
the Route Points List and press the Thumb
Stick In.
52
Rino® 110 Owner’s Manual
UNIT OPERATION > ROUTE PAGE
Adding or Editing from the Route Map
Page
You can use the panning arrow with the Route Map Page
displayed to add or edit route waypoints.
To add a point at either end of a route:
1. Select the Route from the list of routes. Press the
Thumb Stick In to display the Route Page.
2. Highlight the on-screen Map button at the bottom
of the page and press the Thumb Stick In to
display the Route Map Page.
3. Use the Thumb Stick to move the panning arrow
to either end of the displayed route until the end
point is highlighted. Then press the Thumb Stick
In and select Add Turns. This option appears only
when highlighting the end point of a route.
4. Move the panning arrow to a map item or
location where you would like to extend the route
and press the Thumb Stick In to display the
Information Page for the new point.
Rino® 110 Owner’s Manual
5. Press the on-screen Use button to return to the
Map Page and then press the Thumb Stick In
again to place the new waypoint.
To add a route point within a route:
1. Follow steps 1 and 2 in the previous instructions.
2. Use the Thumb Stick to move the panning arrow
to a route line. When the arrow touches the line,
the line becomes thin. Press the Thumb Stick In
to display the word ADD next to the line.
3. Drag the line to a map item or other location
where you want to establish a new waypoint and
then press the Thumb Stick In to place the new
waypoint. A Waypoint Information Page displays.
Press the on-screen OK button to save the new
waypoint, then press it again after returning to the
Route Map.
53
UNIT OPERATION > ROUTE PAGE
To review or remove a route point:
1. Select the Route from the list of routes. Press the
Thumb Stick In to display the Route Page.
2. Use the Thumb Stick to highlight Map and press
In to display the route on the map.
3. Use the Thumb Stick to move the map panning
arrow to the point you want to review and press In.
Select Review or Remove and press In again to
either display the Information Page or remove it
from the route.
Select Next and press In again to view the next
waypoint.
Select Add Turns to manually add a turn to the
route using the map and map pointer.
To navigate a route:
1. Select a route from the list of routes and then
press the Thumb Stick In.
2. Highlight the on-screen Navigate button at the
bottom of the page and then press the Thumb
Stick In to begin navigating the route. The screen
changes to the Navigation Page.
3. Move to the Map Page to view the route and your
current location.
4. Begin moving, watching directional information on
the Navigation Page or your progress on the Map
Page.
Navigating a Route
A Route can be navigated using the Map Page or
the Navigation Page. The Map Page displays your
movement, the route line, and waypoints on the route.
The Navigation Page shows compass direction and a
bearing pointer.
54
Rino® 110 Owner’s Manual
UNIT OPERATION > ROUTE PAGE
Stopping Navigation
To stop navigation, highlight the Stop Navigation option
on either the Navigation or Map Page’s Option Menu or
select the Stop button on the Route Page.
Data Fields for the Route Page
When navigating a Route, the data displayed in the data
fields on the Route Page may be customized to provide
useful navigation information.
To select data field options:
1. Use the Thumb Stick to highlight a data field on
the Route Page and then press In to display the
data field options.
2. Use the Thumb Stick to highlight the desired
option and press In to select that option for the
selected data field.
Rino® 110 Owner’s Manual
Changing the Route Data Fields
Data field options for Route Page:
• Distance to Point
• ETA To Point
• ETE To Point
• Leg Course
• Leg Distance
• Leg Time
• Pointer
• Sunrise At Point
• Sunset At Point
55
UNIT OPERATION > TRACKS PAGE
Tracks Page
To save and use a Track:
The Rino 110 draws an electronic bread crumb trail on
the Map Page as you travel along. This bread crumb trail
is the Track Log. The Track Log contains information
about points along its path, including time and position.
The Rino 110 uses this information to allow you to
navigate using the saved track. You may also save tracks
from other Rino users as they communicate with you.
To open the Tracks Page:
1. Access the Menu Page by using the on-screen
menu button
or the Page key.
2. Select the Tracks icon and press the Thumb
Stick In. The Tracks Page opens.
1. Access the Tracks Page from the Main Menu.
Press the on-screen Off button In to pause track
logging. When track logging is active the On
button appears to be recessed.
2. Highlight the Save on-screen button and then
press the Thumb Stick In to display the track log
Save Back Through list.
3. Use the Thumb Stick to select the time and date
that you would like to save the track through.
4. Press the Thumb Stick In to save the track log
and display the Tracks Page. The Tracks Page
shows the track name (which can be renamed
using the keyboard for data entry), the total
distance of the track, track area (if available), a
Show on Map option, and on-screen buttons for
Map, OK, and Tracback.
Tracks Page
56
Rino® 110 Owner’s Manual
UNIT OPERATION > TRACKS PAGE
Using the TracBack Feature
The TracBack feature allows you to return along a
traveled path (or another Rino user’s path) without
marking any waypoints. When you are ready to return
to where you started, the Rino 110 takes you back by
following the Track Log that you left behind. You can
save a total of 20 tracks in the unit memory. The Track
Log starts recording as soon as the unit gets a satellite
location fix and the Track Log feature is turned on. When
you no longer need a Track Log you can press the onscreen Clear button to remove it.
If you want to keep a record of a certain track log or use
the TracBack feature, it is recommended that you clear
the Track Log before you start traveling. The percentage
of memory used by the current track log is displayed in
a window at the top of the page. After the Track Log is
cleared, it displays zero percent.
Rino® 110 Owner’s Manual
When the display reaches 100%, the most recent track
points start to overwrite the least recent if the default
setting Wrap When Full remains selected on the track
log setup. To avoid losing track points you want, save the
Track Log when it approaches the 99% mark. The active
track log stores up to 2,048 points.
The Saved Track Page displays the track and it can also
be displayed on the Main Map Page as you navigate. You
may save up to 20 tracks with 125 points per track in the
unit. Saved Contact tracks count towards this total. Tracks
are marked BEGIN and END.
57
UNIT OPERATION > TRACKS PAGE
To use the TracBack feature:
1. Highlight the Tracback button on the Tracks Page
and press the Thumb Stick In. The Tracback
Menu options (To Beginning and To End) are
displayed.
2. Highlight the desired option and press the Thumb
Stick In to enable.
3. Use the Map Page or the Navigation Page to
navigate the Track.
Setting up the Track Log
You can set the track recording interval to Distance,
Time, or Automatic. You can set the Track display
resolution to High, Medium, Low, and Lowest. You can
also use the Option Menu to delete all saved tracks.
58
To use Track Log Setup options:
1. Highlight the Tracks Page Option Menu button
at the top of the page and press the Thumb
Stick In to display the menu.
2. Highlight the Tracks Log Setup option and then
press the Thumb Stick In.
You can check the Wrap When Full option by
highlighting it and then pressing the Thumb Stick
In. You can highlight the Record Method and
Interval fields and press the Thumb Stick In to
display their options. Interval options change to
accommodate the Record Method choices.
Rino® 110 Owner’s Manual
UNIT OPERATION > PROXIMITY PAGE
Proximity Page
To add a proximity point:
The Proximity Page lets you define an alarm circle around
a stored waypoint/contact position, and can be used to
help you avoid dangerous areas or to alert you when you
have strayed too far away from other Rino users. Up
to ten waypoints may be listed, with a maximum alarm
radius of 99.99 nautical or statute miles or kilometers.
If entering a proximity alarm circle, a “Near Proximity
Point <name>” message appears. If leaving a proximity
alarm circle, a “Leaving Proximity Point <name>”
message appears.
To access the Proximity Page:
1. Press the Page key or the Menu icon
the Main Menu.
2. In the Main Menu,
scroll down and
select Proximity.
to open
1. Use the Thumb Stick to highlight an empty space
on the Proximity list and press the Thumb Stick
In to display the Find ‘N Go screen. Highlight an
item from the list and press the Thumb Stick In to
open the item.
2. From the Review Page, select Use. Press In again
to begin entry of the proximity radius. Use the
Thumb Stick to enter a distance and press In.
To clear one or all proximity point(s) from the
list:
1. To clear a single alarm, use the Thumb Stick to
highlight the proximity point to clear and press In.
Choose Remove and press In.
2. To clear all proximity waypoints, highlight the
Option Menu
and press In. Choose Remove
All and press the Thumb Stick In.
To turn proximity alarms on or off:
Use the Thumb Stick to highlight Proximity
Alarms and press In to place a check mark.
Proximity Waypoints Page
Rino® 110 Owner’s Manual
59
UNIT OPERATION > SATELLITE PAGE
Satellite Page
The Satellite Page provides a picture of satellite signal
tracking, tells you when the unit is ready for navigation,
and shows your location coordinates.
To access the Satellite Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select
Satellite.
Signal
Strength Bars
Skyview
Graphic
the horizon around you. The inner ring represents a
view above you at a 45° angle from vertical. The center
represents directly overhead. Signal Strength Bars for
each satellite are shown to the left of the Sky View.
Satellites and their signals appear as hollow shapes until
a signal is received and then they appear darkened in. The
stronger the signal, the taller the signal bar.
90°
Center dot - 90°
above the horizon
Inner ring- 45°
above the horizon
Outer ring the horizon
45°
Satellite Page
Sky View graphic
The Sky View graphic represents a view looking up at
the sky from your current location showing satellites
and their assigned numbers. The outer ring represents
60
Rino® 110 Owner’s Manual
UNIT OPERATION > SATELLITE PAGE
WAAS
The Wide Area Augmentation System (WAAS) capability
produces a more accurate position fix. When enabled
(GPS set to Normal and WAAS set to Enabled through
the System Setup Page; also the interface must be set
to something other than RTCM mode), this feature
searches for WAAS satellites near your location and
then receives data for correcting differentials in the
GPS satellite signals. WAAS satellite numbers begin at
number 33 or above and are displayed on the Satellite
Page. When differential correction data has been received
for GPS satellites (numbers 32 or below), a D displays
in the signal bar. It is helpful to orient the unit antenna
toward the WAAS satellite shown in the skyview. To
learn more about the WAAS System, refer to the Federal
Aviation Administration Web
site (http://gps.faa.gov/).
Because the Rino 110 relies on
satellite signals to provide you
with navigational guidance,
the unit’s view of the sky
Satellite Page using WAAS
Rino® 110 Owner’s Manual
determines how fast you achieve navigational status. GPS
signals do not travel through heavy objects or people: For
best results, keep the unit in clear view of the sky.
Satellite Strength
At least three satellite signals are needed to determine
your location; otherwise the unit displays a “Poor
Satellite Reception” message with four options:
Use with GPS Off—select this option if you want
GPS off.
New Location—select this option if you have moved
more than 600 miles (from where you last used the unit).
Restart Search—select this option if today is not date
provided.
Continue Acquiring—select this option if no other
option applies. The unit attempts to gather GPS signals.
61
UNIT OPERATION > SATELLITE PAGE
Satellite Page Options
Satellite Page Option Menu
To select the Use With GPS Off option:
1. Use the Thumb Stick to highlight the Option
Menu button
at the top of the page and then
press it In.
2. Use the Thumb Stick to highlight the Use With
GPS Off option and then press it In.
The Rino 110 stops tracking satellites and cannot
be used for navigation. However, the next time
you turn the unit on, it returns to Normal GPS
operation.
62
To select Track Up or North Up:
1. Use the Thumb Stick to highlight the Option
Menu button
at the top of the page and then
press it In to display the Option Menu.
2. Highlight either the Track Up or North Up option
(depending on which is currently in use), and
press the Thumb Stick In to activate.
To enter a new location:
1. Use the Thumb Stick to highlight the Option
Menu button
at the top of the page and then
press it In.
2. Highlight New Location and press the Thumb
Stick In to display choices of Auto or Use Map.
If you choose Automatic the Rino 110 determines
your new location automatically.
If you choose Use Map, a map page displays with
instructions stating, “Point to your approximate
location and press ENTER.” Use the Thumb Stick
to move the map pointer to your location on the
map and press the Thumb Stick In.
Rino® 110 Owner’s Manual
UNIT OPERATION > SETUP PAGES
Setup Pages
The Setup Pages allow you to customize the Rino 110 to
your personal preferences. You can choose time settings,
units of measure, display backlighting and contrast
settings, heading measurement, interface options and
system operating mode.
To access the Time Setup Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Time icon to open the Time Setup
Page.
By highlighting the icons on the Setup Menu and then
pressing the Thumb Stick In, you can display the Setup
Page for each of the menu items.
To access the Setup Menu:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select Setup.
There are then several more icons to choose from
in the Setup Menu.
Time Setup Page
Time Setup Page
Time Format—allows you to choose from 12-hour (like
a standard clock with 12-hour AM and PM cycles) or 24hour time format ( a 24-hour cycle, also called Military
Time).
You can set the time to match your location or for a
projected location anywhere in the world.
Rino® 110 Owner’s Manual
63
UNIT OPERATION > SETUP PAGES
Time Zone—can be set to one of the eight US Time
Zones or 24 International Time Zones (nearest city or
geographical region). Select Other so you can enter the
UTC Time Offset.
Daylight Savings Time—can be turned On or Off or set
to Automatic.
To set the time:
1. Use the Page key to access the Main Menu.
2. Use the Thumb Stick to highlight the Setup Icon.
Press the Thumb Stick In to display the Setup
Menu.
3. Use the Thumb Stick to highlight the Time Icon.
Press the Thumb Stick In to display the Time
Page.
4. Use the Thumb Stick to highlight the Time Zone
field. Press the Thumb Stick In to display the time
zone list.
5. Highlight a time zone from the list and then press
the Thumb Stick In.
64
6. If you choose Other, you must enter a UTC offset
value. The correct time displays at the bottom of
the page.
Units Setup Page
The Units features are best used by individuals with a
working knowledge of map grids and datums. To learn
more about these subjects, visit the National Geospatial–
Intelligence Agency at http://www.nima.mil or inquire at
your local library.
To access the Units Setup Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Units icon to open the Units Setup
Page.
Units Setup Page
Rino® 110 Owner’s Manual
UNIT OPERATION > SETUP PAGES
Position Format—allows you to choose from different
grid formats. The default position format, hddd°mm.
mmm displays the latitude and longitude in degrees and
minutes and is most commonly used. The following
additional formats are available:
hddd.ddddd°—latitude/longitude in decimal degrees;
hddd°mm.mmm’—latitude/longitude in decimal
numbers; hddd°mm’ss.s”—latitude/longitude in degrees,
minutes, seconds; British Grid; Dutch Grid; EOV
Hungarian Grid; Finnish Grid; German Grid; Icelandic
Grid; India Zones; Irish Grids; Loran TD; Maidenhead;
MGRS; New Zealand; QNG Grid; RT90; South African
Grid; Swedish Grid; Swiss Grid; Taiwan Grid; US
National Grid; UTM/UpS—Universal Transverse
Mercator / Universal Polar Stereographic grids; W
Malayan RSO; and User UTM Grid.
LORAN TD Format
When creating new waypoints using LORAN TD
coordinates, you must set the correct LORAN chain
number and secondary stations in the Setup TD field
Rino® 110 Owner’s Manual
before storing the waypoint. After the waypoint is stored
in unit memory, it always references the LORAN chain
number and secondary stations currently selected in the
Setup TD field. If you enter a different LORAN chain
number or change the secondary stations or offsets in the
Setup TD field, the active waypoint information reflects
those changes. Because the unit does not rely on the
LORAN signal for navigation, it can reference a different
GRI chain and/or secondary stations and still navigate to
the location stored in memory.
To adjust the Loran TD settings, select Loran TD as the
Position Format to open the Loran TD setup window. To
change the settings of any fields, highlight the field, and
press the Thumb Stick In. When done, highlight Save
and press In.
For more information on Loran TDs, you may download
Garmin’s Loran TD Position Format Handbook from
the Garmin Web site at http://www.garmin.com/support/
userManual.jsp.
65
UNIT OPERATION > SETUP PAGES
Map Datum—offers a selection of nearly all map datums
in common use. Every map is based on a map datum (a
reference model of the earth’s shape) and is usually listed
in the title block of the map. If you are comparing GPS
coordinates to a paper map, chart, or other reference, the
map datum in this field must match the horizontal map
datum used to generate the map or other reference. The
default datum is WGS-84 (World Geodetic Survey 1984)
and should only be changed when using maps or charts
specifying a different datum. If a map does specify a
datum, use the options list to find datums applicable to
the region of the map, selecting the one that provides the
best positioning at a known point. If necessary, you also
may choose the User datum for custom designed grids.
NOTE: The User datum is based on a WGS-84-Local datum and is an advanced feature for unlisted
or custom datums. To learn more, check your local
library or the Internet for educational materials on
datums and coordinate systems.
Distance/Speed—choose from three units of measure to
display your rate of travel.
Elevation/Vertical Speed—choose from two units of
measure to record your elevation and vertical speed.
Display Setup Page
You can adjust the amount of time that the backlighting
feature stays on and adjust the screen contrast.
Backlighting Timeout—choose from Stays On or delays
of 15 seconds, 30 seconds, one minute, or two minutes
before timing out.
Contrast Adjustment—can be adjusted from light to
dark using the slider adjacent to the contrast bar.
66
Rino® 110 Owner’s Manual
UNIT OPERATION > SETUP PAGES
To access the Display Setup Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Display icon to open the Display Setup
Page.
To adjust the contrast:
1. Highlight the contrast slider and then press the
Thumb Stick In.
2. Move the Thumb Stick Up or Down to move the
slider to increase or decrease the contrast.
Heading Setup Page
You can select the type of heading displays, the types of
North References, or enter the magnetic variation.
To access the Heading Setup Page:
Display Setup Page
To set the backlighting timeout:
1. Highlight the Backlight Timeout field and then
press the Thumb Stick In.
2. Highlight the desired option and then press the
Thumb Stick In.
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Heading icon to open the Heading
Setup Page.
Heading Setup Page
Rino® 110 Owner’s Manual
67
UNIT OPERATION > SETUP PAGES
Display—allows you to choose from Cardinal Letters,
Degrees or Mils.
North Reference—you can choose from True, Magnetic,
Grid or User options. If User is chosen, you must correct
for the Magnetic Variation.
To access the Interface Setup Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Interface icon to open the Interface
Setup Page.
To select either option:
1. Highlight the field and then press the Thumb
Stick In to display the options.
2. Highlight the option and press the Thumb Stick In
to activate.
Interface Setup Page
The Interface Setup Page allows you to choose from
different input/output serial data formats. This feature
is used when connecting to external NMEA devices, a
DGPS beacon receiver, a personal computer, etc. See the
“Appendix” for using the Rino 110 with MapSource.
Interface Setup Page
The available interface formats are:
Garmin—the proprietary format used to exchange
waypoint, track, and map data with a PC. Use this setting
for transferring data when using a MapSource product.
Garmin DGPS—allows DGPS input using a Garmin
beacon receiver and a standard RTCM SC-104 and DGPS
tuning.
68
Rino® 110 Owner’s Manual
UNIT OPERATION > SETUP PAGES
NMEA In/NMEA Out—supports the output of standard
NMEA 0183 version 3.0 data. Use this for real-time
plotting with MapSource or 3rd party programs.
Text Out—allows ASCII text output of location and
velocity information without input capabilities.
RTCM IN—allows DGPS input using a standard RTCM
SC-104 format without output capabilities.
RTCM In/NMEA Out—allows DGPS input using a
standard RTCM SC-104 format and supports the output
of standard NMEA 0183 version 3.0 data.
RTCM In/Text Out—allows DGPS input using a
standard RTCM SC-104 format and simple ASCII text
output of location and velocity information.
If Garmin DGPS or RTCM In/NMEA Out format
is selected, additional fields are provided to control
a Garmin differential beacon receiver (e.g. GBR 23)
directly from your unit. Tuning is automatic with Scan
or you can enter the beacon frequency and bit rate when
you select User from the Beacon list to manually tune the
receiver. Refer to the beacon receiver instructions.
To select a serial data format:
1. Highlight the Serial Data Format field and then
press the Thumb Stick In.
2. Highlight an option and then press the Thumb
Stick In to activate it.
None—provides no interfacing capabilities.
Interface Setup Page
Rino® 110 Owner’s Manual
69
UNIT OPERATION > SETUP PAGES
System Setup Page
The System Setup Page allows you to change GPS
operation modes, use the WAAS capabilities, turn the
Message Beep on or off, and choose the battery type. See
the “Appendix” for WAAS capability information.
To access the System Setup Page:
1. Press the Page key or the
Menu icon
to open the
Main Menu.
2. In the Main Menu, scroll
down and select Setup.
3. Select the System icon to System Setup Page
open the System
Setup Page.
Choose one of the four GPS options other than Normal
to significantly save battery power. The Battery Saver
mode reduces the rate of satellite signal position updating
and the GPS Off option stops satellite signal reception
altogether. The Demo Mode simulates navigation.
To change the battery type:
1. Use the Thumb Stick to highlight the Battery
Type field and then press In.
2. Then use the Thumb Stick to select the desired
option and press In.
The Option Menu
allows you restore defaults or
display the current version of unit operating software and
the Unit I.D. Number. Software updates and instructions
for downloading are available from the Garmin Web site
(www.garmin.com).
70
Rino® 110 Owner’s Manual
UNIT OPERATION > CALENDAR
Calendar
To change the month and year:
This feature provides you with a monthly calendar with
programmable reference notes. You can display one
monthly calendar at a time and add reference notes using
the data entry keypad. Days that are shaded have notes
added. You can create reference notes for multiple months
and for months in years yet to come. You can record 100
notes with up to 18 characters each.
Highlight the left or right arrows on either side
of the date and press the Thumb Stick In. The
left arrow shows past months/years and the right
arrow shows future months/years.
To use the current month and year
Choose Set To Current Date from the Option
Menu
.
To create a reference note for a selected date:
Calendar Page
1. Use the Thumb Stick to highlight the day of the
month and then press In to display the pop-up
Menu (containing New Note, View Sun & Moon,
and View Hunt & Fish).
2. Highlight and select New Note to begin entering
text from the keyboard.
To access the Calendar:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select
Calendar.
Rino® 110 Owner’s Manual
71
UNIT OPERATION > CALENDAR
To edit or delete a note:
1. To edit or delete a note previously created,
highlight the date and press the Thumb Stick In.
2. Select Edit Note, or Delete Note, from the pop-up
menu. To complete the deletion of the note, press
the Thumb Stick In when Yes is highlighted in the
pop-up window.
3. To edit the note, change the desired characters
using the keyboard as shown in the image to the
right. Press OK when you are finished editing the
note.
To delete notes by week:
1. Choose Delete Notes... from the Option
Menu
.
2. From the Older Than... window, choose the
desired option and press the Thumb Stick In.
To view information for a date:
1. In the calendar, select the desired date using the
Thumb Stick.
2. Review the note in the note window below the
calendar.
3. Press the Thumb Stick In to display the pop-up
menu.
4. Select View Sun & Moon to view the Sun & Moon
Page for that date. Select View Hunt & Fish to
view the Hunt & Fish Page for that date.
Editing a note
72
Rino® 110 Owner’s Manual
UNIT OPERATION > ALARM CLOCK
Alarm Clock
This feature provides an alarm for the system clock. Enter
a time in the time field and turn the alarm on and off from
the control field menu. Remember to enter alarm times
in the same time format (UTC or local) you are using for
your system. The unit must be on for the alarm clock to
work.
To access the Alarm Clock:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select
Alarm Clock.
To set an alarm clock time:
1. Use the Thumb Stick to highlight the time field
and then press In to display the keyboard.
2. Use the Thumb Stick to enter the desired time,
choose OK and press In.
Rino® 110 Owner’s Manual
Alarm Clock Page
To turn the alarm clock On/Off:
1. Use the Thumb Stick to highlight the Alarm
Mode field and then press In to display the
options.
2. Choose On or Off and press the Thumb Stick In.
When the alarm sounds, a brief tone is heard (unless
Message Beep is Off under System Setup) and “Alarm
Clock” appears on the screen. Press the Thumb Stick In
to acknowledge the alarm.
73
UNIT OPERATION > CALCULATOR
Calculator
To change calculator options:
This feature provides you with all the basic functions of
both a standard or scientific calculator. You can perform
most calculations identified by the function symbols
along the sides of the keypad and can save the results
temporarily in the memory. The memory is cleared either
manually or when you turn off the Rino 110.
To access the Calculator:
1. Highlight the page Option Menu
and press
the Thumb Stick In to display the Scientific/
Standard and Radian/Degrees options.
2. Highlight the option you want to change and then
press the Thumb Stick In.
3. Use the Thumb Stick to move about the
calculator, enter numbers, and perform
calculations.
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select
Calculator.
Calculator Page
74
Rino® 110 Owner’s Manual
UNIT OPERATION > STOPWATCH
Stopwatch
This feature allows you to use the unit as a stopwatch,
including using it as a lap timer. You may also have the
unit record the lap time based on distance. For example,
if you set the lap distance to one mile, the unit records the
time it takes you to travel one mile.
To access the Stopwatch:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select the
Stopwatch icon.
To use the Stopwatch:
1. Use the Thumb Stick to highlight the Start field
and then press In. You may also press the Volume
(V) key to start the stopwatch.
2. Use the Thumb Stick to highlight the Stop field
and then press In. You may also press the Volume
(V) key to stop the stopwatch.
3. To mark a lap, use the Thumb Stick to highlight
the Lap field and then press In, with the stopwatch
running. You may also press the Zoom (Z) key to
capture the lap time.
4. Reset the stopwatch when the timer is stopped.
Use the Thumb Stick to highlight the Reset field
and then press In. You may also press the Zoom
(Z) key to reset the times.
Stopwatch Lap Options
You can set the stopwatch to Lap by Distance so that each
time a certain distance has been travelled, the stopwatch
automatically marks a lap. You can enter a specific lap
distance by selecting Set Lap Distance. To return to
manually marking each lap, open the Option Menu
and select the Lap by Button Press option.
Stopwatch Page
Rino® 110 Owner’s Manual
75
UNIT OPERATION > SUN & MOON
Sun & Moon
This feature provides you with a graphic display of both
sun and moon positioning for a certain date, time and
location with times for sunrise, sunset, moonrise, and
moonset.
To access the Sun & Moon Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select the Sun
& Moon icon.
To view information for a different date and
time:
1. To view the sun and moon information for a
specific date or time, highlight each field, then
press the Thumb Stick In to begin data entry of
individual characters.
2. To display the current date and time, highlight the
page Option Menu
and press the Thumb
Stick In to display Use Current Time. Press the
Thumb Stick In.
76
To set the location:
1. Highlight the Location field and then press the
Thumb Stick to display the New Location
options list.
2. Highlight the option desired and then press In
on the Thumb Stick to activate. If you choose
Current Location, the field values displayed on
the page displays your location. If you choose Use
Map, a map page displays. Use the map pointer
to identify the desired location and then press In
on the Thumb Stick. If you choose Use Find ‘N
Go Menu follow instructions in the “Find ‘N Go”
section.
Sun & Moon Page
Rino® 110 Owner’s Manual
UNIT OPERATION > HUNT & FISH
Hunt & Fish
This feature provides you with a listing of best times for
hunting and fishing for a chosen location and date.
To access the Hunt & Fish Page:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select the Hunt
& Fish icon.
To view information for a different date:
1. Highlight the date field and then press In on the
Thumb Stick to begin data entry of individual
characters.
2. To display the current date, highlight the page
Option Menu and press the Thumb Stick In to
display the Use Current Date openu
Rino® 110 Owner’s Manual
77
UNIT OPERATION > AREA CALCULATOR
Area Calculator
This feature provides you an area calculation as you
move about a location or view a saved track. The area
calculation displays in acres, hectares, and square feet,
square yards, square meters, square kilometers, and
square miles.
To access the Area Calculator:
1. Press the Page key or the Menu icon
to open
the Main Menu.
2. In the Main Menu, scroll down and select the Area
Calculator icon.
Area Calculation Page
To review the area of a saved track:
1. On the Tracks Page, highlight a Saved Track.
2. Press the Thumb Stick In to see a map with the
area shown in a data field at the bottom.
To calculate the area:
1. Be sure the Rino 110 has a GPS fix.
2. Press Start when you are ready to begin.
3. Begin walking or traveling the perimeter (edge) of
the area you want to measure.
4. Use the Thumb Stick to stop the calculation when
you have traveled the desired distance.
5. Use the Thumb Stick to store the area as a saved
track.
78
Rino® 110 Owner’s Manual
UNIT OPERATION > GAMES
Games
The Games Page includes Memory Race, Waypoint
Bomber, Clothesline, and Assimilation. Highlight the
appropriate icon and then press the Thumb Stick In to
play the desired game. Brief instructions are displayed
when you start each game. All players must be on the
same channel/squelch code to play.
Memory Race
Be the first to clear the board by matching all of the two
symbols sets together. Each symbol is in a square (you
can adjust the size) that you need to walk or travel to.
Once your position appears in a square, highlight Open at
the bottom of the screen and press the Thumb Stick In.
Play by yourself or race against others. Press Page to quit
at any time.
To adjust the Grid Size or Square Size:
1. Highlight the Grid Size or Square Size field and
press In on the Thumb Stick.
2. Choose the desired size and press In.
Rino® 110 Owner’s Manual
3. Highlight Start and press In to begin the game.
Memory Race
Waypoint Bomber
In this game, it is good to stay on the move! Two or
more players attempt to “bomb” each other. Move your
cursor around on the Map Page using your Thumb Stick.
When you think an opponent is close to your cursor,
drop a bomb. The receiving radio shows an “Incoming”
message. If the receiving radio is within the blast circle
(about 45 feet), it displays a message that you have been
hit. You must wait 30 seconds between shots to reload.
79
UNIT OPERATION > GAMES
Either have a timed game with the winner being the one
with the least amount of hits on their radio, or play until
someone gets a specified number of hits (that person
loses). Hint: mark stationary objects such as trees and
poles, and drop a bomb when an opposing player is near
that object! Adjust the rules to your liking.
• To fire at the cursor location, press the Thumb
Stick In.
• To fire at your current location, press the Talk key.
• Press Call to view the scoreboard at any time.
• Press Page to quit the game at any time.
Clothesline
Team members select the same user symbol and then
attempt to “hit” or “clothesline” other players by pressing
the Talk key when an opposing team member is between
them. You may also mark a point and assign it a symbol
to be used as a stationary team member. Wait 30 seconds
between attempts. Press Call to view the score and Page
to quit the game.
Assimilation
Think of this as a high-tech game of tag. Team members
select the same user symbol and then attempt to
assimilate others into their team by getting within 30 feet
of them and pressing the Talk key. Press Call to show the
score and Page to quit the game. You can set a time limit
so the largest team wins, or play until the other team is
completely assimilated. Set your own rules and enjoy!
Waypoint Bomber
80
Rino® 110 Owner’s Manual
APPENDIX > SPECIFICATIONS
Specifications
Physical
Case:
Size:
Fully-gasketed, high-impact plastic alloy,
waterproof to IPX7 standards (waterproof to
one meter for 30 minutes)
4.5” H x 2.3” W x 1.6” D; 7” H with antenna
(11.4 x 5.8 x 4.1; 17.8 cm)
Weight: Approx. 7.6 ounces (236 g) with batteries
Temperature Range:
-4° to 158° F (-20° to 70° C) (operating range)
Display: 1.4” H x 1.4” W (3.6 cm x 3.6 cm)
160 x 160 pixels, high-contrast LCD
Performance
GPS Receiver:
WAAS Enabled, Differential-ready,
12 parallel channel
Rino® 110 Owner’s Manual
Acquisition time:
Approx. 15 seconds (warm start)
Approx. 45 seconds (cold start)
Approx. 5 minutes (First Time/AutoLocate®)
Update Rate:
1/second, continuous
GPS Accuracy: <15 meters (49 ft) RMS, 95% typical1
DGPS (USGC) Accuracy: 3–5 meters (10–16 ft), 95%
typical with DGPS corrections2
DGPS (WAAS) Accuracy:
<3 meters (10 ft), 95% typical with
DGPS corrections2
Velocity Accuracy: 0.05 meter/sec steady state
Dynamics:
Performs to specifications to 6 g’s
Interfaces:
NMEA 0183, RTCM 104
(for DGPS corrections)
and RS-232 for PC interface
Antenna:
Quad-helix
81
APPENDIX > SPECIFICATIONS
Radio
Channels:
Specifications are subject to change without notice.
1–14 FRS,
15–22 GMRS (requires FCC license
in the U.S.)
Squelch Codes: 1–38
Range: Up to 2 miles on FRS; up to 5 miles on GMRS
Radio Output Power:
FRS 0.5 watt; GMRS 1.0 watt
Power
Input: Three 1.5 Volt AA batteries3
Battery Life:
GPS only: up to 41 hours;
FRS only: up to 20 hours;
FRS and GPS: up to 14 hours4
82
Subject to accuracy degradation to 100m 2DRMS under the U.S.
DoD-imposed Selective Availability program.
1
With optional Garmin Differential Beacon Receiver Input (such as
Garmin GBR 23).
2
3
The temperature rating for the Rino 110 may exceed the usable
range of some batteries. Alkaline batteries can rupture at high
temperatures. External power can only be applied using the
Garmin Auto Power Adapter or PC Interface Cable with Auto
Power Adapter. These cables contain a 12 VDC to 4.5 VDC
voltage regulator. Modifications or other applications voids the
product warranty. Alkaline batteries lose a significant amount of
their capacity as temperature decreases. Extensive use of screen
backlighting and the radio significantly reduces battery life.
Different brands of batteries vary in performance.
5, 5, 90 Duty Cycle - 5% receive with audio unmuted, 5%
transmit and 90% standby (receive with audio muted)
4
Rino® 110 Owner’s Manual
APPENDIX > ACCESSORIES
Accessories
To obtain accessories, see your local dealer or visit the
Garmin Web site at www.garmin.com.
Headset with VOX Boom Mic—hands-free at its best!
Utilize the Rino’s VOX (Voice Operated Transmission)
feature with this headset and voice activated boom mic.
12-Volt Adapter Cable—provides unit power from an
automobile cigarette lighter.
Instructional Video—for getting accustomed to your
Rino basic operations quickly.
2.5 to 3.5 mm Jack Adapter—allows you to use 3rd
party headsets with your Rino unit.
MapSource Map Data CD-ROMs—an excellent
tool for creating waypoints and routes on your PC and
downloading them to your Rino.
Bash Guard Kit—helps protect the Rino’s edges against
hard shocks. Includes 2 bash guards, quick-release neck
lanyard, and belt clip.
NiMH Battery Charger—includes NiMH battery
charger and 4 AA NiMH batteries.
Carrying Case—protects the Rino and permits use while
in the case.
PC Data Cable and 12-Volt Adapter—allows transfer
of waypoints and routes from a PC to the Rino and
provides unit power from an automobile cigarette lighter.
Earbud with PTT (Push To Talk) Mic—earbud and a
clip-on mic with PTT button.
Flexible Ear Receiver—comfortable ear piece for better
hearing ability of your Rino.
Rino® 110 Owner’s Manual
Rail/Handlebar Mount—allows you to mount your Rino
on most rails or handlebars.
Suction Cup Mount—allows you to mount your Rino on
most smooth surfaces or windshields.
83
APPENDIX > TRANSFERRING MAPSOURCE DATA
Transferring MapSource Data
If you have purchased a Garmin MapSource CD-ROM
mapping program, you may want to transfer detailed data
before beginning use to provide your unit with maximum
Find features. The Rino 110 accepts up to 1 MB of map
data from the MapSource Points of Interest. It is not
possible to transfer 3rd party maps into Garmin products.
Map data transfer requires the use of a PC, a Garmin
MapSource CD-ROM, and the PC Interface Cable with
RS-232 serial port connector supplied with this unit.
Follow detailed instructions for data transfer in the
MapSource User’s Manual.
3. Connect the remaining cable connector to the
back of the Rino 110 by orienting the slot on the
connector with the indexing bar on the back of the
unit and push the connector until it is fully seated
in the unit.
4. Turn on the Rino 110 and follow instructions for
map data transfer provided in the MapSource
User’s Manual. See also the “Interface Setup
Page” section for unit interface settings.
To setup for data transfer:
1. Remove weather cap from the Power/Data Port
on the back of the unit by lifting up on the rubber
weather cap.
2. Connect the serial port connector on the cable to
an available serial port on your computer.
84
Rino® 110 Owner’s Manual
APPENDIX > WHAT IS FRS?
What is FRS?
FRS, or Family Radio Service, is a UHF radio frequency
band allocated by the FCC for general public use. The
operating frequency ranges from 462.5625 to 467.7125
MHz, with a maximum transmitting power of one half
watt. FRS radios are small and lightweight, making them
ideally suited for outdoor activities. FRS radios typically
feature a half watt of transmit power. You can expect
your FRS radio to offer reliable operation at a one-mile
range. If the area between you and another FRS operator
is free of obstructions, operation up to two miles can be
achieved. FRS radios broadcast on one of 14 channels,
each with a specific frequency within the FRS band.
The use of FRS radios does not require a license. FRS
was intended for use by families and small groups as an
inexpensive means of two-way voice communication.
FRS is intended for use throughout the United States, its
territories and possessions. It may also be used in Canada.
FRS is not approved outside of these areas and
Rino® 110 Owner’s Manual
may interfere with local government communication
frequencies (fire, police, etc.).
FRS Features
More sophisticated FRS radios also include call
functions, squelch codes, channel scan features, and voice
scramble capabilities. Call functions allow you to push
a Call button on the radio to alert other radios set on the
same channel. This feature generates a call tone and is
handy in a noisy environment where the tone is easier to
initially identify than plain speech.
Squelch codes allow you to selectively block out other
FRS users that are not part of your group. They will still
be talking with others in their own group, but you will not
hear them on your radio. They may or may not hear you
and members of your group on their own radios. Squelch
codes act as a filter, blocking your FRS radio from
hearing other unwanted FRS users. Remember though,
these are public-use frequencies and everyone has a right
to talk or listen in.
85
APPENDIX > WHAT IS FRS?
Channel scan allows your FRS radio to scan all FRS
frequencies for signals. After scanning briefly to see what
channels other users are on, simply set your FRS radios to
an unused channel and enjoy less interference.
FRS Limitations
If you are operating in an urban environment or in
varying terrain such as canyons or mountains, some
features act as obstructions limiting the maximum
reception range of your FRS radio. The UHF FRS
frequencies are “line of sight,” meaning that the signals
do not follow the surface of the earth, but instead radiate
in a straight line from the transmitting antenna. If there
is an obstruction between the transmitting FRS radio and
the receiving FRS radio, the signal will not be received.
Smaller obstructions, such as trees, cars, and even crowds
of people cause some loss of signal, resulting in reduced
maximum range.
86
GMRS
The use of a GMRS (General Mobile Radio Service)
radio requires an FCC license in the U.S. No license is
required in Canada to operate on GMRS channels. The
operating frequency of GMRS ranges from 462.550 to
462.725 MHz. Refer to the “Frequency Charts” for a
complete list of each channel’s frequency.
Rino® 110 Owner’s Manual
APPENDIX > GPS TROUBLESHOOTING GUIDE
GPS Troubleshooting Guide
Symptom
Probable Cause
Remedy
Unit does not turn on.
Batteries are exhausted.
Replace batteries.
Unit does not turn on, even with new batteries.
Batteries may be installed backwards.
Reinstall batteries.
You are pressing and releasing the Power button.
You must press and hold the Power button for 2 seconds.
The unit turns on, then turns off.
Batteries may be nearly exhausted.
Replace batteries.
It takes more than ten minutes to get a location fix
The unit’s view of satellites is obstructed.
Move to a locatin with a clear view of the sky.
Cannot access a WAAS system satellite after 2 to 5
minutes.
Your view of the satellite is obstructed or you are
located too far from satellites currently in service for the
Americas
Move to a location with a clear view and point the unit
antenna in the direction of the satellite.
System GPS operation is set to something other than
Normal and/or interface setting is set for RTCM.
Set system GPS to Normal and interface to other than
RTCM. Or simply turn off WAAS.
Cannot obtain a differential position from WAAS
You have not collected enough information from the
WAAS satellite.
Wait 10–20 minutes for the initial collection, then 1–2
minutes afterwards.
Cannot access Point of Interest, Street, or Intersection
Find Lists.
MetroGuide map data is not activated.
Access the Map Setup Map option and activate the check
box.
Cannot view a track being laid down on the map
page when traveling.
The Track Log feature is turned off.
Access the Tracks Page, highlight the On button and press
the Thumb Stick In.
Cannot see the panning arrow on the Map Page
easily.
There is too much map clutter or the scale is such that
map features are too densely displayed.
Use the Map Page Setup Page to reduce map clutter or
change the map scale.
Cannot exit a menu or page by moving the Thumb
Stick to the Left.
Some menus and pages have an “X” (Exit) on-screen
button in the upper right corner.
Highlight the on-screen button and then press the Thumb
Stick In.
Rino® 110 Owner’s Manual
87
APPENDIX > RADIO TROUBLESHOOTING GUIDE
Radio Troubleshooting Guide
Symbol
Probable Cause
Remedy
Radio not transmitting
Talk key may not be fully depressed
Press and hold Talk key until done talking.
FRS/GMRS Radio feature may not be on.
Turn radio on.
Incorrect channel/Squelch Code setting
Make sure other radios are on the same channel and Squelch Code.
Out of range or obstructions.
Decrease distance between radios.
Limited talk range.
Natural or man-made obstructions can decrease
range.
Decrease distance between radios or obtain a better line of sight
between radios.
You can hear others, but they cannot hear
you, or you see an incoming transmission, but
nothing is heard.
You are on the same channel, but a different
Squelch Code.
If you are using Squelch Code zero (0), you will hear all transmissions
on that channel. Use the same Squelch Code (1-38) as the other party or
use Scan to find what Squelch Code they are on.
Message garbled.
Scramble option is enabled.
Both radios need to have this feature set the same (Rino 110 units do not
have voice scramble).
Too many unwanted conversations being heard.
Too many users on channel or Squelch Code is set
to zero.
Switch to a different channel and/or Squelch Code other than zero
(1–38).
Interference or static.
Radios too far apart or too close. Obstructions in
radio line of sight.
Keep radios at least 3 feet apart. Obtain a better line of sight between
radios.
Interference from other electronics.
Shut off other devices or move to a different area.
Cannot transmit location.
Could be one of a few things: Your view of the
satellite is obstructed and a GPS fix is not available.
Send Location is off. 30 seconds have not elapsed
since last location transmission. GPS is set to off.
Move to a location with a clear view of the sky. Enable Send Location.
Wait 30 seconds between location transmission. Enable GPS.
None of the keys except Talk will work.
Keylock is enabled.
Hold Page for 5 seconds to release keylock.
Messages not being received by others.
88
Rino® 110 Owner’s Manual
APPENDIX > FREQUENCY CHARTS
Frequency Charts
Channel #
Transmit Frequency (MHz)
Channel #
Transmit Frequency
1
2
3
4
5
6
7
8
9
10
11
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
12
13
14
15 (GMRS)
16 (GMRS)
17 (GMRS)
18 (GMRS)
19 (GMRS)
20 (GMRS)
21 (GMRS)
22 (GMRS)
467.6625
467.6875
467.7125
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
Code
1
2
3
4
5
6
7
8
9
10
Frequency
67
71.9
74.4
77
79.7
82.5
85.4
88.5
91.5
94.8
Rino® 110 Owner’s Manual
Code
11
12
13
14
15
16
17
18
19
20
Frequency
97.4
100
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
Code
21
22
23
24
25
26
27
28
29
30
Frequency
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
NOTE: If you plan to purchase
FRS radios from third party
manufacturers be aware that
there are CTCSS differences in
some radios. Some of the tones
on one radio may not be available on other radios. Charts
showing the different Squelch
Codes and manufacturers can
be located on the Internet.
Code
31
32
33
34
35
36
37
38
Frequency
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
89
APPENDIX > DATA FIELD DEFINITIONS
Data Field Definitions
The following data field options are available on the Map,
Navigation, Altimeter, and Trip Computer Pages.
Final ETE—the estimated time needed to reach your final
destination.
GPS Accuracy—the estimated accuracy of the GPS signal.
Bearing—the direction from your current location to a destination.
Heading—your moving direction.
Course—the direction from your starting location to a destination.
Location (lat/lon)—your current GPS position. (Trip Computer
Page Only.)
Current Destination—the next waypoint on your route.
Current Distance—the remaining distance to your next waypoint.
Current ETA—the estimated time of day you will arrive at your
next waypoint.
Current ETE—the estimated time needed to arrive at the next
waypoint on your route.
Elevation—the altitude (height) above or below sea level.
Final Destination—the last waypoint on your route.
Final Distance—the remaining distance to your final destination.
Final ETA—the estimated time of day you will reach your final
destination.
90
Location (selected)—the lat/lon of point defined on map. (Trip
Computer Page Only.)
Maximum Speed—the maximum speed the unit has moved.
Moving Avg. Speed—average speed of the unit while moving.
Odometer—a running tally of distance travelled, based upon the
distance between second-by-second position readings.
Off Course—the distance left or right you are from the original
course (path of travel).
Overall Avg. Speed—your average speed.
Pointer—indicates the direction to the next destination.
Rino® 110 Owner’s Manual
APPENDIX > DATA FIELD DEFINITIONS
Speed—display rate of travel in miles per hour, kilometers per
hour, or nautical miles per hour.
Trip Time–Stopped—a running tally of stopped time elapsed
since last reset.
Sunrise—the time at which the sun rises on this day.
Trip Time–Total—a running tally of all time since last reset.
Sunset—the time at which the sun sets on this day.
Turn—the angle difference (in degrees) between the bearing to
your destination and your current line of travel. L means turn Left.
R means turn Right.
Time of Day—The time for the selected time zone.
To Course—the compass direction you must go in order to get
back to the original course.
Trip Odometer—a running tally of distance travelled since last
reset.
Velocity Made Good—the speed at which you are closing on a
destination along a desired course.
Vertical Speed—your rate of altitude gain/loss over time.
Trip Time–Moving—a running tally of movement time elapsed
since last reset.
Rino® 110 Owner’s Manual
91
APPENDIX > INTERFACE INFORMATION
Interface Information
Interface formats are selected in the Setup Interface Page.
See also the “Transferring MapSource Data” section of
this Appendix for information on using the Rino 110 with
MapSource. The input/output lines on your Rino 110 unit
are RS-232 compatible, allowing easy interface to a wide
range of external devices, including PC’s, differential
beacon receivers, marine autopilots, and /or a second GPS
receiver.
The NMEA 0183 version 3.0 interface format is
supported by the Rino 110 and enables the unit to drive
up to three NMEA devices.
NMEA 0183 Version 3.0 Approved Sentences:
DGPS (Differential GPS) corrections are accepted in
RTCM-SC-104 version 2.0 format through the Data
IN line. The Garmin GBR 21 and GBR 23 are the
recommended beacon receivers for use with the Rino 110.
Other beacon receivers with the correct RTCM format
may be used, but may not correctly display status or
allow tuning control from the GPS unit.
The Rino 110 may be hard-wired to a serial connector
using a Data Only Cable. Refer to the wiring diagram and
the Rino 110 unit data connection illustrated below.
The PC Interface Cable provided with this unit allows
you to connect your Rino 110 to a PC-compatible
computer’s serial port.
GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC,
GPRTE, GPVTG, GPWPL, GPBOD
GARMIN Proprietary Sentences:
PGRME (estimated error), PGRMM (datum string),
PGRMZ (altitude), PSLIB (beacon receiver control)
92
Rino® 110 Owner’s Manual
APPENDIX > SAFETY AND PRODUCT INFORMATION
Safety and Product Information
FCC Compliance Information
The Rino 110 complies with Part 15 of the FCC regulations and
with Canadian RSS-210 and ICES-003 for Class B digital devices.
Operation of this device is subject to the following conditions: (1)
This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
This equipment generates, uses, and can radiate radio
frequency energy and may cause harmful interference to radio
communications if not installed and used in accordance with the
instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet that is on a different
circuit than the receiver’s circuit.
Rino® 110 Owner’s Manual
•
Consult the dealer or an experienced radio/TV technician
for help.
The Rino 110 does not contain any user-serviceable parts. Repairs
should only be made by an authorized Garmin service center.
Unauthorized repairs or modifications could result in permanent
damage to the equipment and void your warranty and your
authority to operate this device.
FCC Licensing Information
The Rino 110 two-way radio operates on General Mobile
Radio Service (GMRS) frequencies regulated by the Federal
Communications Commission (FCC) in the United States.
Operation on the GMRS frequencies is subject to additional rules
as specified in 47 CFR Part 95.
In order to transmit on GMRS frequencies, you are required to
obtain a license from the FCC. An individual 18 years of age
or older, who is not a representative of a foreign government,
is eligible to apply for a GMRS license. To apply for a GMRS
license, you will need FCC Form 605 (605 Main Form and
Schedule F) and FCC Form 159. You can download the application
forms from the FCC Web site at http://www.fcc.gov/Forms/. You
can also request them through the FCC forms hotline at 1-800-418FORM (1-800-418-3676).
93
APPENDIX > SAFETY AND PRODUCT INFORMATION
You can file Form 605 online at http://wireless.fcc.gov/uls/. A
filing fee, which may change from time to time, is associated with
this application.
For information on fees, see the FCC fee information Web page at
http://wireless.fcc.gov/feesforms/index.html. General information
may be found at http://wireless.fcc.gov/services/personal/
generalmobile/.
For questions concerning the license application, contact the FCC
at 1-888-Call-FCC (1-888-225-5322).
No license is required to operate on GMRS channels in Canada.
For use in countries outside of the U.S. and Canada, please check
with that government for any restrictions of FRS or GMRS use.
Limited Warranty
This Garmin product is warranted to be free from defects in
materials or workmanship for one year from the date of purchase.
Within this period, Garmin will at its sole option repair or
replace any components that fail in normal use. Such repairs or
replacement will be made at no charge to the customer for parts
or labor, provided that the customer shall be responsible for any
transportation cost. This warranty does not cover failures due to
abuse, misuse, accident or unauthorized alteration or repairs.
94
THE WARRANTIES AND REMEDIES CONTAINED
HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES EXPRESS OR IMPLIED OR STATUTORY,
INCLUDING ANY LIABILITY ARISING UNDER ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES, WHETHER RESULTING FROM THE USE,
MISUSE, OR INABILITY TO USE THIS PRODUCT OR FROM
DEFECTS IN THE PRODUCT. Some states do not allow the
exclusion of incidental or consequential damages, so the above
limitations may not apply to you.
Garmin retains the exclusive right to repair or replace the unit
or software or offer a full refund of the purchase price at its sole
discretion. SUCH REMEDY SHALL BE YOUR SOLE AND
EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.
Rino® 110 Owner’s Manual
APPENDIX > SAFETY AND PRODUCT INFORMATION
To obtain warranty service, contact your local Garmin authorized
dealer or call Garmin Product Support for shipping instructions
and an RMA tracking number. The unit should be securely packed
with the tracking number clearly written on the outside of the
package. The unit should then be sent, freight charges prepaid, to
any Garmin warranty service station. A copy of the original sales
receipt is required as the proof of purchase for warranty repairs.
Garmin International, Inc.
1200 E 151st Street, Olathe, Kansas 66062 U.S.A.
Tel. 913/397.8200
Fax. 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey,
SO51 9DL U.K.
Tel. 44/0870.8501241
Fax 44/0870.8501251
International Purchases: A separate warranty is provided by
international distributors for units purchased outside the United
States. This warranty is provided by the local in-country distributor
and this distributor provides local service for your unit. Distributor
warranties are only valid in the area of intended distribution. Units
purchased in the United States or Canada must be returned to the
Garmin service center in the United Kingdom, the United States,
Canada, or Taiwan for service.
The Garmin Rino 110 has no user-serviceable parts. Should you
ever encounter a problem with your unit, please take it to an
authorized Garmin dealer for repairs.
The Rino 110 is fastened shut with screws. Any attempt to open
the case to change or modify the unit in any way will void your
warranty and may result in permanent damage to the equipment.
Online Auction Purchases: Products sold through online auctions
are not eligible for rebates or other special offers from Garmin.
Online auction confirmations are not accepted for warranty
verification. To obtain warranty service, an original or copy of the
sales receipt from the original retailer is required. Garmin will not
replace missing components from any package purchased through
an online auction.
Rino® 110 Owner’s Manual
95
APPENDIX > SAFETY AND PRODUCT INFORMATION
Software License Agreement
Product Registration
Garmin grants you a limited license to use the software embedded
in this device (the “Software”) in binary executable form in the
normal operation of the product. Title, ownership rights, and
intellectual property rights in and to the Software remain in
Garmin.
Use this area to record the serial number (8-digit number located in
the battery compartment) in case your Rino 110 is lost, stolen, or
needs service. Be sure to keep your original sales receipt in a safe
place or attach a photocopy inside the manual.
BY USING THE RINO 110, YOU AGREE TO BE BOUND
BY THE TERMS AND CONDITIONS OF THE FOLLOWING
SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS
AGREEMENT CAREFULLY.
You acknowledge that the Software is the property of Garmin and
is protected under the United States of America copyright laws
and international copyright treaties. You further acknowledge
that the structure, organization, and code of the Software are
valuable trade secrets of Garmin and that the Software in source
code form remains a valuable trade secret of Garmin. You agree
not to decompile, disassemble, modify, reverse assemble, reverse
engineer, or reduce to human readable form the Software or any
part thereof or create any derivative works based on the Software.
You agree not to export or re-export the Software to any country
in violation of the export control laws of the United States of
America.
96
Help us better support you by completing our online registration
today! Have the serial number of your Rino 110 handy and connect
to our Web site (http://www.garmin.com). Look for the Product
Registration link on our Home page.
Serial Number: ___ ___ ___ ___ ___ ___ ___ ___
Contact Garmin
If you should encounter any difficulty while using your Rino
110, or if you have any questions, in the U.S.A. contact Garmin
Product Support by phone: 913/397.8200 or 800/800.1020,
Monday–Friday, 8 AM–5 PM Central Time; or by e-mail at
sales@garmin.com. In Europe, contact Garmin (Europe) Ltd. at
44/0870.8501241.
Rino® 110 Owner’s Manual
APPENDIX > SAFETY AND PRODUCT INFORMATION
Warnings and Cautions
The GPS system is operated by the United States government,
which is solely responsible for its accuracy and maintenance. The
system is subject to changes which could affect the accuracy and
performance of all GPS equipment. Although the Garmin Rino 110
is a precision electronic NAVigation AID (NAVAID), any NAVAID
can be misused or misinterpreted and, therefore, become unsafe.
The electronic chart is an aid to navigation and is designed to
facilitate the use of authorized government charts, not replace
them. Only official government charts and notices to mariners
contain all information needed for safe navigation—and, as
always, the user is responsible for their prudent use.
Use the Rino 110 at your own risk. To reduce the risk of unsafe
operation, carefully review and understand all aspects of this
Owner’s Manual—and thoroughly practice operation using the
Demo mode prior to actual use. When in actual use, carefully
compare indications from the Rino 110 to all available navigation
sources, including the information from other NAVAIDs, visual
sightings, charts, etc. For safety, always resolve any discrepancies
before continuing navigation.
Rino® 110 Owner’s Manual
MAP DATA INFORMATION: One of the goals of Garmin
is to provide customers with the most complete and accurate
cartography that is available to us at a reasonable cost. We use a
combination of governmental and private data sources, which we
identify (as required) in product literature and copyright messages
displayed to the consumer. Virtually all data sources contain
inaccurate or incomplete data to some degree. This is particularly
true outside the United States, where complete and accurate digital
data is either not available or prohibitively expensive.
CAUTION: IT IS THE USER’S RESPONSIBILITY TO
USE THIS PRODUCT PRUDENTLY. THIS PRODUCT IS
INTENDED TO BE USED ONLY AS A NAVIGATIONAL AID
AND MUST NOT BE USED FOR ANY PURPOSE REQUIRING
PRECISE MEASUREMENT OF DIRECTION, DISTANCE,
LOCATION, OR TOPOGRAPHY.
IMPORTANT: READ THIS INFORMATION BEFORE
USING YOUR RINO:
Exposure to Radio Frequency Signals—Your wireless handheld
radio is a low power radio transmitter and receiver. When it is
on, it receives and also sends out radio frequency (RF) signals.
In August 1996, The Federal Communications Commissions
(FCC) adopted RF exposure guidelines with safety levels for
handheld wireless radios. Those guidelines are consistent with
97
APPENDIX > SAFETY AND PRODUCT INFORMATION
safety standards previously set by both U.S. and international
standards bodies: American National Standards Institute (ANSI)
IEEE. C95.1-1992; National Council on Radiation Protection
and Measurements (NCRP) Report 86; International Commission
on Non-Ionizing Radiation Protection (ICNIRP) 1996. Those
standards were based on comprehensive and periodic evaluations
of the relevant scientific literature. For example, over 130
scientists, engineers, and physicians from universities, government
health agencies, and industry reviewed the available body of
research to develop the ANSI Standard (C95.1). The design of your
radio complies with the FCC guidelines (and those standards).
For body-worn operation, this radio demonstrates compliance and
meets the FCC RF exposure guidelines when used with approved
accessories supplied with or designed for this product. Use of other
accesssories may not ensure compliance with FCC RF exposure
guidelines.
Antenna Care—Use only the supplied antenna. Unauthorized
antennas, modifications, or attachments could damage the radio
and may violate FCC regulations. Do not use any radio that has a
damaged antenna, because if it comes into contact with your skin,
a minor burn can result.
98
Electronic Devices—Most modern electronic equipment is
shielded from RF signals. However, certain equipment may not be
shielded against the RF signals from your wireless radio.
Pacemakers—The Health Industry Manufacturers Association
recommends that a minimum separation of six inches (6”) be
maintained between a handheld wireless radio and a pacemaker
to avoid potential interference with the pacemaker. These
recommendations are consistent with the independent research by
and recommendations of Wireless Technology Research. Persons
with pacemakers should ALWAYS keep the radio more than six
inches from their pacemaker when the radio is turned on, should
not carry the radio in a breast pocket, should use the ear opposite
the pacemaker to minimize the potential for interference, and
should turn the radio off immediately if you have any reason to
suspect that interference is taking place.
Hearing Aids—Some digital wireless radios may interfere with
some hearing aids. In the event of such interference, you may want
to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices—If you use any other personal medical
device, consult the manufacturer of your device to determine if it is
adequately shielded from external RF energy. Your physician may
be able to assist you in obtaining this information.
Rino® 110 Owner’s Manual
APPENDIX > SAFETY AND PRODUCT INFORMATION
Turn your radio OFF in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health
care facilities may be using equipment that could be sensitive to
external RF energy.
Vehicles—RF signals may affect improperly installed or
inadequately shielded electronic systems in motor vehicles. Check
with the manufacturer or its representative regarding your vehicle.
You should also consult the manufacturer of any equipment that
has been added to your vehicle.
Areas with a potentially explosive atmosphere are often, but not
always clearly marked. They include fueling areas such as gasoline
stations, below deck on boats, fuel or chemical transfer or storage
facilities; vehicles using liquefied petroleum gas (such as propane
or butane); areas where the air contains chemicals or particles,
such as grain, dust, or metal powders; and any other area where
you would normally be advised to turn off your vehicle engine.
Posted Facilities—Turn your radio OFF in any facility where
posted notices so require.
Commercial Aircraft—Many commercial airlines prohibit the use
of FRS radios on board. Switch OFF your radio before boarding an
aircraft or check the airline rules.
Blasting Areas—To avoid interfering with blasting operations,
turn your radio OFF when in a “blasting area” or in areas posted:
“Turn off two-way radio.” Obey all signs and instructions.
Potentially Explosive Atmospheres—Turn your radio OFF
and do not remove your battery when you are in any area with a
potentially explosive atmosphere. Obey all signs and instructions.
Sparks from your battery in such areas could cause an explosion or
fire resulting in bodily injury or even death.
Rino® 110 Owner’s Manual
99
INDEX
Symbols
3D Accuracy 7
A
Accessories 83
Accuracy 81
Acquisition time 81
Add to Route 41, 42, 44,
46
Alarm 59, 73
Arriving at Destination 48
Arrow 25
Attention Tone 15
Auto Zoom 27
B
Battery Icon 6
Battery Life 82
Battery Type, Changing 70
Bearing 29
Bearing Pointer 29, 31, 48
Bread Crumb Trail 56
Broken Signals 16
Broken Transmission 12
Buttons Locked 35
C
100
Calculator 74
Calendar 71
Call 85
Call Tone 15
CDI 30
Change Route 50
Change Scales 23
Channel 10
City 44
Clock 73
Compass 29
Contact 18, 43
Course 29
Course Deviation Indicator 30
Course Pointer 30, 31
CTCSS 10, 89
Current Location 36
D
Data Fields 26, 31, 55
Definitions 90
For Route Page 55
Data Transfer 84
Defaults 4, 24, 31, 32,
51, 70
Delete Waypoint 39
Detail 27
DGPS 92
Direct Route 48
Display Mode 27
E
Editing
Routes 50
Waypoints 38
F
Family Radio Service 1,
85. See also FRS
FCC 85
License 86
Filter Unwanted Noise 10,
12
Finding
City 44
Contact 43
Near Map Pointer 44
Point of Interest 45
Find ‘N Go 40, 48, 50
Fishing information 77
FRS 1, 7, 10, 85, 89
G
Games 79
Garmin sentences 92
General Mobile Radio
Service 1. See
also GMRS
GMRS 1, 7, 10, 14, 85
Goto 41, 42, 43, 44, 45, 48
GPS
On/Off 16, 61
Status 16
GRI Chain 65
H
Headset Microphone 15
Hunting Information 77
Hunt & Fish 41, 42, 44,
46, 77
I
Informational Picture 16
Initialize 7
Interfaces 81
Interface formats 92
Internal Microphone 15
Rino® 110 Owner’s Manual
INDEX
K
Keylock 5, 35
L
Lap 75
Last Found Place 47
License Agreement 96
Lock
Buttons/Keys 5, 35
LORAN TD Format 65
M
Main Display Pages 4
Main Menu 33
MapSource 1, 22, 49, 69
Map Data 28, 84
Map Detail 27
Map Features Setup 28
Map Page 22
Options 24
Overview 22
Pan Map 24
Restore Defaults 24
Scale 23
Setup Map 24, 27
Map Pointer 25
Rino® 110 Owner’s Manual
Mark Waypoint 16
Mark Waypoint Page 36
Measure Distance 24, 28
Message Beep 70
Microphone 15
Monitor Channels 12
Move a Waypoint 39
My ID 8
N
Name 8
Navigate 30, 54
Navigation Page 29–31
Bearing Pointer/Course
Pointer 31
Options 31
Restore Defaults 31
Stop Navigation 31
New Contact 18
New Location 62
NMEA 0183 92
North Heading 27
North Up 27, 62
Note 71
O
Operating the Rino 5
Option Menu 5
Orientation 27
P
Page Sequence Setup 34
Pan Map 24, 25
PC 84, 92
PC Interface Cable 84
Peer-to-Peer 14, 18
PIT 15
Points of Interest 45, 46
Polling 14
Poll Location 43
Position Icon 22
Program a Data Field 26
Project Waypoint 38, 41,
42, 43, 44, 46
Proximity Alarms 59
R
Radio Page 7
Channel 10
Code 10
Informational Picture 16
Overview 7
Setup Radio 14
Radio Transmission Status
16
Receive Signals 7
Recently Found Places 47
Reference Note 71
Reposition Here 41, 42
Reset 32, 75
Restore Defaults 24, 32
Reverse Route 50
Review
Route 51
Ring Tone 15
Roger Tone 15
Routes 49
Copy 51
Create 49
Data Fields 55
Delete 51
Edit 50
Navigate 54
Remove waypoints 50
Restore defaults 51
Reverse 50
Review 51
101
INDEX
Use 49
S
Satellite Fix 7
Satellite Information 7
Satellite Page 59
GPS Off 61
Options 62
Sky View 60
Save as a Waypoint 44, 46
Scales 23
Scanlist 12, 13, 16
Scan Codes 12, 13, 86
Send Location 14, 18, 21,
41, 42, 43, 44, 46
Set
Alarm clock 73
Proximity 41, 42, 43,
44, 46
Scanlist 12
Setup
Map 24, 27
Page 63
Radio 14
Scanlist 16
TD field 65
102
Time Page 63
Tones 15
Shortcut Menu 5, 35
Show... 24
Show Data Fields 31
Signal Strength 60
Size 81
Sky View 60
Specifications 81
Squelch codes 10, 85
Status Bar 6
Icons 6
Stopwatch 75
Stop Navigation 24, 31
Sun & Moon 41, 42, 44, 46
Symbol 8
Changing 9
T
Text Setup 28
Thumb Stick 2, 5
Time Page 63
Tones 15, 73
Call 15
Ring 15
Roger 15
Setup 15
TracBack 57
Track 29
Log 56
Page 56
Setup 28
Tracking Satellites 7
Track Log 22
Track Up 62
Transferring 84
Transmit Location 18, 21
Trip Computer Page 32–41
Options 32
Reset 32
Two-way Radio 1, 85, 93
U
Track 43
Voice Operated Transmission 14
VOX 14
W
WAAS 61, 70
Waterproof 1, 81
Waypoint 36, 37
Create 36, 37
Delete 39
Edit 38
Move 39
Project 38
Z
Zoom 23, 27
UHF 85
Units Page 64
Unlock Buttons 5, 35
Unwanted Calls
Ignore 10
V
View
Contact 23
Rino® 110 Owner’s Manual
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin web site at www.garmin.com.
© Copyright 2002–2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00251-10 Rev. D
Download PDF

advertising