Product information guide | Garmin 19800149402 GPS Receiver User Manual

GPSMAP® 4000/5000 Series Installation Instructions
The GPSMAP 4000/5000 series chartplotter and GPS antenna must be properly installed according to the following instructions. You need the
appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers.
Caution
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
notice
When drilling or cutting, always check what is on the opposite side of the surface.
Mount the GPSMAP 4000/5000 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the
controls or touch screen.
Contact Garmin Product Support if you have any questions while installing your GPSMAP 4000/5000 Series chartplotter. In the USA, go to
www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020.
In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
In Europe, go to www.garmin.com/support and click Contact Support for in-country support information, or contact Garmin (Europe) Ltd. by
phone at +44 (0) 870.8501242.
Before installing your GPSMAP 4000/5000 series chartplotter, confirm that the package contains the items listed on the box. If any parts are
missing, contact your Garmin dealer immediately.
Warning
See the Important Safety and Product Information guide in the product box for product warnings and other important information.
To install the GPSMAP 4000/5000 series chartplotter, you must:
1. Mount the GPSMAP 4000/5000 series chartplotter (page 2).
2. Mount the GPS antenna (page 5).
3. Connect the GPSMAP 4000/5000 series device to power and to the GPS antenna (pages 8-9).
4. Create a NMEA 2000 network or connect the chartplotter to an existing NMEA 2000 network (page 10).
5. Connect the GPS 19x antenna to the NMEA 2000 network (page 10).
6. Ensure the chartplotter software is up-to-date (page 20).
Although they are not necessary to use the GPSMAP 4000/5000 chartplotter, this manual covers other installation options:
• Connecting the chartplotter to other Garmin Marine Network compatible devices, such as a sounder or a radar (page 15).
• Connecting the chartplotter to other NMEA 0183-compatible devices such as a VHF radio with DSC (page 15).
• Connecting the chartplotter to an external alarm (page 18).
• Connecting the chartplotter to a video input source (page 19).
• Connecting the chartplotter to an external video monitor (page 19).
March 2012
Part Number 190-01494-02 Rev. A
Printed in Taiwan
Mounting the GPSMAP 4000/5000 Series Chartplotter
You can mount the GPSMAP 4000/5000 series chartplotters one of two ways. You can use the included bracket to bail mount the chartplotter, or
you can use the included template and hardware to flush mount the chartplotter.
Notice
You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger size, you must flush mount the GPSMAP 5015/5215 chartplotters.
Bail Mounting the GPSMAP 4000/5000 Series Chartplotter
Use the included bracket to bail mount the GPSMAP 4000/5000 series chartplotter.
Tools required (not included):
• Drill and drill bit
• Screwdriver
• Pencil
• Mounting hardware (screws or nuts, washers, and bolts)
NOTE: The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are 5/16 in. (7.9 mm) in
diameter. Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size
of the drill bit required depends on the mounting hardware chosen.
To install the bail-mount bracket:
NOTE: You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger
size, you must flush mount the GPSMAP 5015/5215 chartplotter.
1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to
leave at least 5 in. (12.7 cm) of clearance behind the 4000/5000 series chartplotter for the
wiring.
Mounting
screws
Bail-mount
bracket
NOTE: Mount a GPSMAP 4008/4208/5008/5208 chartplotter 31 1/2 in. (80 cm), and a
GPSMAP 4010/4210/4012/4212/5012/5212 chartplotter 39 3/8 in. (1 m) from a magnetic
compass to avoid interference.
2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.
3. Secure the bail mount to the surface with screws and washers.
To install the GPSMAP 4000/5000 series chartplotter on the bailmount bracket:
1. Loosely attach the mounting knobs to the GPSMAP 4000/5000 series
chartplotter.
2. Slide the chartplotter onto the bail mount, and tighten the mounting knobs.
2
Mounting knobs ×2
GPSMAP 4000/5000 Series Installation Instructions
Flush Mounting the GPSMAP 4000/5000 Series Chartplotter
The flush-mount method you will use with your chartplotter is dependent on the model. Be sure to follow the instructions for your chartplotter
model.
Flush Mounting a GPSMAP 4008/4208/4012/4212 Chartplotter or a GPSMAP 5008/5208/5012/5212
Chartplotter
Hardware (included):
• Flush-mount template
• Rubber gasket
• Four threaded 4 mm mounting studs
• Four 4 mm flat washers
• Four 4 mm lock washers
• Four 4 mm nuts
Tools required (not included):
• Jigsaw
• Masking tape
• Scissors
• Drill
• Drill bits—3/8 in. (10 mm) and 4 mm
• 1/16 in. (2 mm) Allen (Hex) wrench
• 4 mm socket or wrench
• Center punch and hammer
To flush mount a GPSMAP 4008/4208/4012/4212 chartplotter or a GPSMAP 5008/5208/5012/5212 chartplotter:
1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location at which you want to flush
mount the chartplotter.
NOTES:
• Make sure the surface on which you mount the chartplotter has at least 7 in. (18 cm) of open space behind it to fit the chartplotter and the
connected wires.
• Make sure to leave approximately 1/2 in. (13 mm) of space on the right side of the chartplotter to access the SD card door.
• Mount a 4008/4208/5008/5208 chartplotter 31 1/2 in. (80 cm), and a 4012/4212/5012/5212 chartplotter 39 3/8 in. (1 m) from a magnetic
compass to avoid interference.
2. The flush-mount template has adhesive on the back. Remove the protective liner and apply the template to the mounting location.
3. Using a 3/8 in. (10 mm) drill bit, drill one or more of the four pilot holes inside the corner of the template to begin cutting the mounting surface.
4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the flush-mount template. Use a file and sandpaper
to refine the size of the hole.
Notice
Be very careful when cutting this hole. There is only a small amount of clearance between the case and the mounting holes.
5. Install the four mounting studs by screwing them into the back of the chartplotter. Use the 1/16 in. (2 mm) Allen wrench to tighten the mounting
studs until they stop. The studs are coated with a reusable thread-locking patch applied at the factory.
notice
Do not use power tools to tighten the mounting studs. Doing so may cause you to overtighten.
Do not overtighten - you may damage the mounting stud or the mounting holes.
6. Place the chartplotter in the hole and make sure that the mounting studs line up with the pilot holes on the flush-mount template after cutting,
sanding, and filing the hole. If they do not, mark the locations where the studs will feed through the mounting surface.
7. Using the center punch, indent the center of each of the 4 mm mounting-hole locations.
8. Using a 4 mm drill bit, drill the four mounting holes.
9. Install the rubber gasket on the back of the chartplotter. The top and bottom sections will line up with the holes. The side sections will line up
with the notches in the case (for the cover).
10.Place the chartplotter into the cutout. The four mounting studs should feed through the four mounting holes drilled in step 8.
11.Place the flat washers and the lock washers over the mounting studs. Then thread the hex nuts onto the mounting studs. Tighten all four hex
nuts evenly until the chartplotter is snug against the mounting surface.
GPSMAP 4000/5000 Series Installation Instructions
3
Chartplotter
Mounting studs ×4
Rubber gasket
Mounting surface
Lock washers ×4
Flat washers ×4
Hex nuts ×4
Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter
Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter:
Hardware (included):
• Flush-mount template
• Rubber gasket
• Mounting screws (4.2 × 1.4 DIN7981 / number 8 ANSI)
Tools required (not included):
• Jigsaw
• Masking tape
• Scissors
• Drill
• Drill bits—3/8 in. (10 mm)
• Center punch and hammer
• Anti-seize lubricant (optional)
To flush mount a GPSMAP 4010/4210 chartplotter or a GPSMAP 5015/5215 chartplotter:
1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location where you want to flush mount
the chartplotter.
Notes:
• Make sure the surface on which you mount the chartplotter has at least 7 in. (18 cm) of open space behind it to fit the chartplotter and the
connected wires, and make sure to leave approximately 1/2 in. (13 mm) of space on the right side of the chartplotter to access the SD card
door.
• Mount a 4010/4210 chartplotter 31 1/2 in. (80 cm), and a 5015/5215 chartplotter 23 5/8 in. (60 cm), from a magnetic compass to avoid
interference.
2. The flush-mount template has adhesive on the back. Remove the protective liner and apply
the template to the location at which you want to mount the chartplotter.
3. Using a 3/8 in. (10 mm) drill bit, drill a pilot hole inside the corner of the template to begin
cutting the mounting surface.
4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the
flush-mount template. Use a file and sandpaper to refine the size of the hole.
5. If the top and bottom mounting covers are attached to the front of the chartplotter, remove
them by unsnapping the covers from the sides.
Mounting covers ×2
4
GPSMAP 4000/5000 Series Installation Instructions
6. Place the chartplotter in the hole, and make sure that the mounting holes on the chartplotter line up with the pilot holes on the flush-mount
template after cutting, sanding, and filing the hole. If they do not, mark the locations where the pilot holes need to be.
7. Using the center punch, indent the center of each of the mounting-hole locations.
8. Using the 3/8 inch drill bit, drill the mounting holes.
NOTE: If you are mounting the chartplotter in fiberglass, it is recommended to use a countersink bit to drill a clearance-counterbore through only the top
gel-coat layer. This will help to avoid any cracking in the gel-coat layer when the screws are tightened.
9. Install the rubber gasket on the back of the chartplotter. The top and bottom sections will line up with the holes. The side sections will line up
with the notches in the case for the sun cover.
NOTE: To prevent corrosion of the metal contacts, cover unused connectors (page 20) with the attached weather caps.
10.Place the chartplotter into the cutout.
11.Securely tighten the included mounting screws through the chartplotter into the pilot holes.
Note: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainless antiseize lubricant to the screw before using.
12.Replace the mounting covers by snapping them into place.
Mounting the GPS 19x Antenna
notice
Be sure to follow the correct mounting directions and the correct wiring directions for the antenna included with your chartplotter.
You can surface mount the antenna, attach it to a standard marine pole mount, or install the antenna under fiberglass.
Mounting Location Considerations
To ensure the best reception, keep these considerations in mind while selecting a mounting location.
• Mount the antenna in a location that has a clear, unobstructed view of the sky in all directions.
• Mount the antenna where it is not covered by the superstructure of the boat, a radar device, or
➊
a mast ➊.
• On a sailboat, avoid mounting the GPS antenna high on the mast to prevent inaccurate speed
readings caused by excessive heeling.
• Do not install the antenna near sources of electromagnetic interference (EMI) ➋, such as the
motor or other large marine electronics.
• Install the antenna at least 3 ft. (1 m) away from the path of a radar beam or VHF radio
antenna ➌.
• It is best to install the antenna above the path of the radar beam ➍.
➌
• It is acceptable to install the antenna under the path of the radar beam ➎.
• Install the antenna at least 2 in. (5 cm) from a magnetic compass to avoid interfering with the compass.
➋
➍
➎
Verifying a Mounting Location
1. Select a mounting location.
2. Temporarily secure the antenna in the selected location.
3. Test the antenna for correct operation on the chartplotter.
4. If you experience interference with other electronics, try a different location.
5. Repeat steps 3 and 4 until you find a mounting location where the antenna operates correctly.
After you verify correct operation at the mounting location, permanently mount the antenna.
GPSMAP 4000/5000 Series Installation Instructions
5
Mounting the Antenna on a Surface
1. Select a mounting location for the antenna, and verify correct operation at the mounting location.
2. Trim the surface-mount template, and make sure the antenna fits in the mounting location you selected.
3. Remove the protective liner on the back of the template, and apply the template to the mounting location.
4. Use a 1/8 in. (3.2 mm) bit to drill the three pilot holes indicated on the template.
Notice
If you are mounting the GPS 19x on fiberglass, it is recommended to use a countersink bit to drill a clearance counterbore through the top gelcoat layer (but
no deeper). This helps to avoid cracking in the gelcoat layer when the screws are tightened.
5. Use a 3/8 in. (10 mm) bit to drill a starter hole for the jigsaw blade, as indicated on
the template.
6. Use a jigsaw to cut the center hole as indicated on the template.
7. Use the three M4 screws ➊ to secure the surface-mount bracket ➋ to the
mounting surface ➌.
8. Make sure the large gasket is in place on the bottom of the antenna ➍.
9. Route a NMEA 2000 drop cable through the center hole, and connect it to the
antenna ➎.
10.Place the antenna on the surface-mount bracket, and twist it clockwise to lock it in
place.
11.Secure the antenna to the mounting bracket with the M3 set screw ➏.
12.Route the NMEA 2000 drop cable away from sources of electronic interference.
➏
➊
➍
➎
➋
➌
13.Connect the antenna to your NMEA 2000 network.
Mounting the Antenna on a Pole
Using the pole-mount bracket, you can install the antenna on a standard marine pole
Mount (not included). A standard threaded marine pole mount has the following characteristics:
• An outer diameter (OD) of 1 inch
• Threads that measure 14 threads per inch
Note: An external cellular antenna is not compatible with the pole-mount bracket.
Mounting the Antenna with the Cable Routed Outside of the Pole
1. Select a mounting location for the antenna, and verify correct operation at the mounting location.
➌
2. Route a NMEA 2000 drop cable through the pole-mount bracket ➊.
3. Place the cable in the vertical slot ➋ along the base of the pole-mount bracket.
4. Thread the pole-mount bracket onto a standard marine pole mount (not included).
Do not overtighten the bracket.
5. Connect the NMEA 2000 drop cable to the antenna.
6. Place the antenna on the pole-mount bracket, and twist it clockwise ➌ to lock it in place.
7. Secure the antenna to the bracket with the M3 set screw ➍.
8. Fasten the marine pole mount to the boat if it is not already attached.
9. Route the NMEA 2000 drop cable away from sources of electronic interference.
10.Connect the antenna to your NMEA 2000 network.
11.After the antenna has been installed on the pole mount, fill the remaining gap in the vertical cable slot with a
marine sealant (optional).
➍
➊
➋
Mounting the Antenna with the Cable Routed through the Pole
1. Select a mounting location for the antenna, and verify correct operation at the mounting location.
2. Temporarily position a standard marine pole mount (not included) in the mounting location you selected.
3. Mark the approximate center of the pole.
6
GPSMAP 4000/5000 Series Installation Instructions
4. At the marked location, use a 3/4 in. (19 mm) bit to drill a hole for the cable to pass through.
5. Fasten the marine pole mount to the boat (hardware not included).
6. Thread the pole-mount bracket ➊ onto the marine pole mount.
Do not overtighten the bracket.
7. Route a NMEA 2000 drop cable through the pole-mount bracket and the pole, and connect the cable to the antenna.
8. Place the antenna on the pole-mount bracket, and twist it clockwise ➌ to lock it in place.
9. Secure the antenna to the bracket with the included M3 set screw ➍.
10.Route the NMEA 2000 drop cable away from sources of electronic interference.
11.Connect the antenna to your NMEA 2000 network.
12.After the antenna is installed on the pole mount, fill the vertical cable slot with a marine sealant (optional).
Mounting the Antenna under a Surface
NOTICE
When choosing a location to install the under-deck-mounting bracket, make sure the included screws are not too long for the surface thickness. If the screws
are not appropriate for the surface, you must supply the correct length of M4 screws to avoid damage to the top of the mounting surface.
The antenna can be mounted under a fiberglass surface. Because the antenna has difficulty acquiring cellular signals through metal, it is
recommended that you use the under-deck mount under a fiberglass surface.
1. Identify the mounting location on the fiberglass surface ➊, and verify correct operation
at the mounting location.
2. Using the under-deck-mounting bracket ➋ as a template, mark three pilot-hole locations
➌ on the surface.
3. Use a 1/8 in. (3.2 mm) bit to drill the three marked pilot holes.
4. Place the antenna in the bracket, and twist it clockwise to lock it in place.
5. Secure the antenna to the bracket with the included M3 set screw ➍.
6. Remove the backing from the adhesive pads ➎ on the under-deck mounting bracket.
7. Make sure that the bracket aligns with the pilot holes, and adhere the under-deck
mounting bracket to the surface.
8. Using screws of the appropriate length, fasten the bracket to the surface.
9. Connect a NMEA 2000 drop cable to the antenna ➏.
10.Route the NMEA 2000 drop cable away from sources of electronic interference.
11.Connect the antenna to your NMEA 2000 network.
GPSMAP 4000/5000 Series Installation Instructions
➊
➎
➋
➌
➍
➏
7
Wiring and Cables
The GPSMAP 4000/5000 series chartplotter comes with a power cable, a NMEA 2000 drop cable, a 19-pin NMEA 0183 data cable, and a
17-pin Marine Video cable. Optional Garmin Marine Network components use specialized Garmin Network cables. Depending on the
installation, it may be necessary to drill holes to route the connector end of these cables.
Garmin rubber grommets are provided to cover these holes for a finished look.
Trim to this line for
You may not need the grommets in some installations. The grommets do NOT create a
the Marine Video
waterproof seal. Apply a marine sealant around the grommet and cable after installation.
cable.
Be sure to test the system before installing and sealing the grommets. Purchase additional
grommets from your Garmin dealer or directly from Garmin at www.garmin.com.
Use this hole (no
trim) for the power,
NMEA, Marine
Network, or
GPS 17 cable.
Tools
•
•
•
•
Drill
1 1/4 in. (31.7 mm) paddle drill bit or hole saw
Utility knife
Marine sealant (optional)
Split
To install the cable grommet:
1. Mark the location where you want to route the cable (power, NMEA 0183, NMEA
2000 Marine Video, or Marine Network).
2. Using a 1 1/4 in. (31.7 mm) paddle drill bit or hole saw, drill the installation hole.
3. Refer to the diagram for trimming instructions. Carefully trim the cable hole in the
grommet, as needed.
4. Route the cable to the chartplotter, and test the system.
5. Spread the grommet apart at the split and place it around the cable.
6. Firmly push the grommet into the installation hole until it is seated. Apply marine
sealant, as needed, to weatherproof the cable.
Installing Locking Rings on the Cables
To help make the cable-routing process easier, the locking rings are packaged separately from the cables. Each locking ring is packaged in a
small bag with a number on the label for easy identification. After you route the cables, use the following table to identify the correct locking
ring for each cable:
Cable
Power
Connector
Color
Red
NMEA 0183
Blue
Video
Yellow
Locking Ring
Number
➀
➁
➂
Replacement Locking
Ring Part Number
010-11170-01
010-11170-02
010-11170-00
Notes:
• The NMEA 2000 cables and connectors come with the locking rings pre-installed. Do not remove the locking ring from a NMEA 2000 cable
while routing the cable.
• Optional Garmin Marine Network components use specialized Garmin Network cables (not included). Each network cable is also
packaged with a separate locking ring, in a bag labeled with a ➃. A network-cable specific locking ring should not be used with a
GPSMAP 4000/5000 cable.
Installing a locking ring on a cable:
1. Route the cable away from sources of electronic interference so that the cable connector is at the mounting location of the chartplotter.
2. Use the table above to identify the correct locking ring for the cable, and locate the locking ring bag by number.
3. Separate the two halves of the locking ring.
4. Align the two halves of the locking ring over the cable and snap them together.
8
GPSMAP 4000/5000 Series Installation Instructions
5. Insert the O-ring into the end of the connector.
Installing a Locking Ring
Wiring the Power Cable
The GPSMAP 4000/5000 series chartplotter must be connected to the power supply for the boat. Use the 2-pin power cable included, and
connect the power (red) and ground (black) wires.
notes:
• Use 14 AWG shielded wiring for extended runs of wire to the power cable.
• Solder all connections and seal them with heat-shrink tubing.
GPSMAP 4000/5000 Series Installation Instructions
9
Connecting the GPSMAP 4000/5000 Series Chartplotter and the GPS 19x Antenna to Your
NMEA 2000 Network
The GPSMAP 4000/5000 series chartplotter is packaged with the necessary NMEA 2000 connectors and cable to either connect the GPSMAP
4000/5000 series chartplotter and GPS 19x antenna to your existing NMEA 2000 network, or to build a basic NMEA 2000 network. For more
information on NMEA 2000, visit www.garmin.com.
Connecting to an Existing NMEA 2000 network
If your boat already has a NMEA 2000 network installed, use the included T-connectors and drop cable to connect the GPSMAP 4000/5000
series chartplotter and GPS 19x antenna to the existing network.
To connect the GPSMAP 4000/5000 series chartplotter and GPS 19x to your existing NMEA 2000 network:
1. Determine the appropriate locations to connect the
GPSMAP 4000/5000 series chartplotter and GPS 19x
to your existing NMEA 2000 backbone.
2. Disconnect one side of a NMEA 2000 T-connector from
the backbone nearest to the location where you want
GPSMAP 4000/5000
to connect the chartplotter.
GPS 19x
series chartplotter
antenna
If you need to extend the NMEA 2000 backbone,
connect an appropriate NMEA 2000 backbone
extension cable (not included) to the side of the T-connector you disconnected.
3. Connect an included T-connector in the NMEA 2000
Drop cables
backbone (for the chartplotter).
(included)
NMEA 2000
4. Route an included drop cable to the chartplotter and
device
to the top of the T-connector you added to your NMEA
(not included)
2000 network.
T-connectors
If the included drop cable is not long enough, you can
(included)
add a drop cable extension up to 13 ft. (4 m). If more
cable is needed, add an extension to your NMEA 2000
backbone, based on the NMEA 2000 guidelines.
5. Disconnect one side of a NMEA 2000 T-connector from
the backbone nearest to the location where you want
to connect the GPS 19x antenna.
If you need to extend the NMEA 2000 backbone,
Existing NMEA 2000 network
connect an appropriate NMEA 2000 backbone
(not included)
extension cable (not included) to the side of the Connecting
the
GPSMAP
4000/5000
Series Chartplotter and GPS 19x
T-connector you disconnected.
Antenna to an Existing NMEA 2000 Network
6. Connect an included T-connector in the NMEA 2000
backbone (for the GPS 19x antenna).
7. Route an included drop cable from the GPS 19x antenna to the top of the T-connector you added to your NMEA 2000 network.
If the included drop cable is not long enough, you can add a drop cable extension up to 13 ft. (4 m). If more cable is needed, add an
extension to your NMEA 2000 backbone, based on the NMEA 2000 guidelines.
notice
If you have an existing NMEA 2000 network on your boat, it should already be connected to power. Do not connect the included NMEA 2000 power cable to
an existing NMEA 2000 network.
NOTES:
• The diagram shows only the NMEA 2000 data connection to the GPSMAP 4000/5000 series chartplotter. The chartplotter must also be
connected to power or it will not function. See page 9.
• One GPS antenna will provide position data for every device on the NMEA 2000 network. Do not connect multiple GPS antennas if you are
using multiple chartplotters.
10
GPSMAP 4000/5000 Series Installation Instructions
Creating a Basic NMEA 2000 Network
If your boat does not already have an existing NMEA 2000 network installed, you will need to create a basic NMEA 2000 network. For more
information on NMEA 2000, visit www.garmin.com.
To create a basic NMEA 2000 network
1. Connect the three included T-connectors together by their sides.
2. Connect the appropriate terminators to each end of the combined T-connectors.
3. Wire the included NMEA 2000 power cable to a 12 Vdc power source through a switch. Connect to the ignition switch for the boat if possible.
4. Connect the NMEA 2000 power cable to the top of one of the T-connectors.
5. Route and connect the included NMEA 2000 drop cables from the GPS 19x and from the GPSMAP 4000/5000 series chartplotter to the tops
of the other T-connectors.
GPS 19x
antenna
GPSMAP 4000/5000
series chartplotter
Ignition or
in-line switch
Power cable
Fuse
+
12 Vdc battery
-
Drop cables
Male
terminator
Female
terminator
T-connectors
Creating a Basic NMEA 2000 Network
notes:
• The diagram shows only the NMEA 2000 data connection to the GPSMAP 4000/5000 series chartplotter. The chartplotter must also be
connected to power or it will not function. See page 9.
• One GPS antenna will provide position data for every device on the NMEA 2000 network. Do not connect multiple GPS antennas if you are
using multiple chartplotters.
GPSMAP 4000/5000 Series Installation Instructions
11
Wiring a Garmin Marine Network
The optional Garmin Marine Network is a plug-and-play system that allows for high-speed data transfer between multiple Garmin chartplotters
and other network-compatible Garmin devices such as a Garmin sonar unit (GSD 22), a Garmin radar (GMR 18 or GMR 404/406), or an XM
Weather receiver (GDL 30/30A). The GPSMAP 4000/5000 series chartplotters have three network ports that can be used to connect other
Garmin network-compatible chartplotters and devices. If the network requires more ports, use a Garmin Marine Network port extender (GMS
10), or another GPSMAP 4000/5000. Data from each connected component is shared by all the connected Garmin chartplotters.
Notes:
• NMEA 0183 devices must all be wired to one chartplotter on the network. The data is then shared over the network to other connected
chartplotters.
• Connect all chartplotters to the NMEA 2000 network as well as to the Garmin Marine Network. NMEA 2000 data is not shared over the
Garmin Marine Network.
• Connect network components, such as a Garmin GMR radar, GSD sounder, or GDL XM Weather receiver to any chartplotter on the network
or to an optional GMS 10 Network Port Expander. Data is shared between all chartplotters on the network.
• BlueChart® g2 Vision cartography data is shared with any connected GPSMAP 4000/5000 series chartplotter.
• Video input from the Marine Video cable is only viewable on the chartplotter to which it is connected.
• You can connect a GPSMAP 4000/5000 chartplotter to a Marine Network with a GPSMAP 3000 series chartplotter:
• They will share GPS 17 GPS position information as well as information to and from standard NMEA 0183 devices.
• They will share information from connected network compatible Garmin devices such as a sonar unit (GSD 22), a radar (GMR 18 or
GMR 404/406), or an XM Weather receiver (GDL 30/30A).
• Garmin GPSMAP 3000 series chartplotters CANNOT share cartography data with the GPSMAP 4000/5000 series chartplotters.
• All network components must be connected to the power source for the boat according to their installation instructions. The following
diagrams show only the network connections, not power connections.
• Currently, XM Weather and audio service is only available in the United States (lower 48). Because of this, a connected XM Weather
receiver (GDL 30/30A) will only function in the United States (lower 48).
12
GPSMAP 4000/5000 Series Installation Instructions
Sample Garmin Marine Network Setups:
Garmin GPSMAP
4000/5000 series
chartplotter
Garmin GPSMAP
4000/5000 series
chartplotter
Marine Network with Two Chartplotters
Garmin marine radar
GDL 30/30A XM weather unit
GSD 22 sounder unit
xxxx
x x x x xxxxxxxxxxxxxxxxxxx
To transducer
Garmin GPSMAP
4000/5000 series
chartplotter
Garmin GPSMAP
4000/5000 series
chartplotter
Extended Marine Network With Two Chartplotters
NOTES:
• Every device connected to the Garmin Marine Network must be connected to the power supply for the boat. These diagrams show the
network connections; however, they do not show the power connections. Wire each device according to the appropriate installation
instructions.
• These diagrams show the Garmin Marine Network connections; however, they do not show NMEA 2000 or NMEA 0183 connections.
GPSMAP 4000/5000 Series Installation Instructions
13
Garmin marine radar
GSD 22 sounder unit
xxxx
x x x x xxxxxxxxxxxxxxxxxxx
GMS 10 marine network port expander
To transducer
GDL 30/30A
XM weather receiver
Garmin
GPSMAP 3000 series
chartplotter
Garmin
GPSMAP 4000/5000
series chartplotter
Connecting a GPSMAP 4000/5000 Series Chartplotter to an Existing Garmin Marine Network
NOTES:
• When connecting a GPSMAP 4000/5000 series chartplotter to an existing Garmin Marine Network, the GMS 10 can be used but is not
necessary. The GPSMAP 4000/5000 series chartplotter has three network ports and acts as a port expander. Wire the GPS antenna and
additional NMEA devices to either the existing GPSMAP 3000 series chartplotter or the new GPSMAP 4000/5000 Series chartplotter. The
existing GPSMAP 3000 series chartplotter and the new GPSMAP 4000/5000 series chartplotter share NMEA 0183 data and Garmin Marine
Network data, but do not share cartography.
• Every device connected to the Garmin Marine Network must be connected to the power supply for the boat. This diagram shows the network
connections; however, it does not show the power connections. Wire each device according to the appropriate installation instructions.
• This diagram shows the Garmin Marine Network connections; however, it does not show NMEA 2000 or NMEA 0183 connections.
14
GPSMAP 4000/5000 Series Installation Instructions
Wiring Additional NMEA 0183 Devices
The NMEA 0183 data cable included with the GPSMAP 4000/5000 series chartplotter supports the NMEA 0183 standard, which is used to wire
various NMEA 0183-compliant devices, such as VHF radios, NMEA instruments, autopilots, or a computer.
Basic NMEA 0183 Wiring
These diagrams illustrate basic NMEA 0183 wiring used to connect your GPSMAP 4000/5000 series chartplotter to NMEA 0183-compliant
devices such as an AIS or DSC device. For more-complete information on the NMEA 0183 capabilities of the GPSMAP 4000/5000 series
chartplotter, see the section on advanced NMEA 0183 wiring (page 16).
+
wire color
Fuse
7.5 A - 42 V
Garmin
GPSMAP 4000/5000 series
chartplotter
Power
cable
NMEA 0183
Cable
>
>
>
>
BATTERY
10–35 Vdc
Wire
Red (power)
Red (power)
Black (pwr gnd)
Black (pwr gnd)
Black (data GND)
Black (data GND)
White
Transmit A(+)
orange/white
>
transmit B(-)
Gray
Receive A(+)
pink
receive B(-)
>
>
>
Wiring to a NMEA 0183-compliant Device (AIS)
+
wire color
Fuse
7.5 A - 42 V
Garmin
GPSMAP 4000/5000 series
chartplotter
Power
cable
NMEA 0183
Cable
>
>
>
>
BATTERY
10–35 Vdc
NMEA 0183-compliant
device
(AIS)
-
Red (power)
Wire
Red (power)
Black (pwr gnd)
Black (pwr gnd)
Black (data GND)
Black (data GND)
NMEA 0183-compliant
device
orange/white
white
Transmit
gray
Receive
pink
>
>
unconnected
Wiring to a Single-ended NMEA 0183-compliant Device
Notes:
• If the NMEA 0183-compliant device has only one receiving wire (no A, B, +, or -), leave the pink wire unconnected.
• If the NMEA 0183-compliant device has only one transmitting wire (no A, B, +, or -), connect the orange/white wire to ground.
• Consult the installation instructions of your NMEA 0183-compliant device to identify the Transmit A(+) and B(-) wires and Receive A(+)
and B(-) wires.
• Use 28 AWG, shielded, twisted-pair wiring for extended runs of wire.
• Solder all connections and seal them with heat-shrink tubing.
GPSMAP 4000/5000 Series Installation Instructions
15
Advanced NMEA 0183 Wiring
The GPSMAP 4000/5000 series chartplotter features four ports to receive NMEA 0183 data (RX ports), and two ports to send NMEA 0183 data
(TX ports). Wire one NMEA 0183 device per RX port to send data to a 4000/5000 series chartplotter. Wire up to three NMEA 0183 devices in
parallel to each TX port to receive data from a 4000/5000 series chartplotter.
Each RX and TX port has 2 wires, labeled A (+) and B (-) according to the NMEA 0183 convention. Connect the corresponding A (+) and B (-)
wires of each port to the A (+) and B (-) wires of your NMEA 0183-compliant device. Refer to the table and wiring diagrams when wiring the
4000/5000 chartplotter to NMEA 0183 devices.
Consult the installation instructions of your NMEA 0183-compliant device to identify the Transfer (TX) A(+) and B(-) wires and
Receiving (RX) A(+) and B(-) wires. Use 28 AWG, shielded, twisted-pair wiring for extended runs of wire. Solder all connections and seal
them with heat-shrink tubing.
Notes:
• For two-way communication with a NMEA 0183 device, the ports on the GPSMAP 4000/5000 chartplotters are not linked. For example,
if the RX port of the NMEA 0183-compliant device is wired to TX port 1 on the GPSMAP 4000/5000, you can wire the TX port of your
NMEA 0183-compliant device to RX port 1, port 2, port 3, or port 4 on the GPSMAP 4000/5000.
• The ground wires on the NMEA 0183 data cable from the GPSMAP 4000/5000 series chartplotter and your NMEA 0183-compliant device
must both be grounded.
• Approved NMEA 0183 sentences—GPBWC, GPRMC, GPGGA, GPGSA, GPGSV, GPGLL, GPBOD, GPRMB, GPRTE, GPVTG,
GPWPL, GPXTE, and Garmin proprietary sentences­—PGRME, PGRMM, and PGRMZ.
• The GPSMAP 4000/5000 series chartplotter also includes support for the WPL sentence, DSC, and sonar NMEA 0183 input with support for
the DPT (depth) or DBT, MTW (water temperature), and VHW (water temperature, speed, and heading) sentences.
• Use the Communications section of the Configure menu on the GPSMAP 4000/5000 series chartplotter to set up NMEA 0183
communications. See the owner’s manual for details.
Port
Wire Function
Wire Color
Pin Number
Receiving Port 1
RX / A (+)
White
1
RX / B (-)
Orange/White
2
RX / A (+)
Brown
5
RX / B (-)
Brown/White
6
Receiving Port 3
RX / A (+)
Violet
9
RX / B (-)
Violet/White
10
Receiving Port 4
RX / A (+)
Black/White
11
rX / B (-)
Red/White
12
Transmitting
Port 1
tX / A (+)
Gray
3
tX / B (-)
Pink
4
Transmitting
Port 2
tX / A (+)
Blue
7
tX / B (-)
Blue/White
8
N/A
GPS 17 in
Green/White
13
N/A
GPS 17 out
Green
14
N/A
spare
Receiving Port 2
Connector
Pin 1
Pin 3
Pin 8
Pin 17
NMEA 0183 Cable End
View
15
N/A
Alarm
Yellow
16
N/A
Accessory on
Orange
17
N/A
Ground
Black
18
N/a
spare
19
GPSMAP 4000/5000 Series NMEA 0183 Data Cable
16
GPSMAP 4000/5000 Series Installation Instructions
+
Wire
Fuse
7.5 A - 42 V
Garmin
GPSMAP 4000/5000 series
chartplotter
Power
cable
NMEA 0183
Cable
Battery
10–35 Vdc
Wire
see table for
wire colors
Red (power)
Red (power)
Black (pwr gnd)
Black (pwr gnd)
Black (data GND)
Black (data GND)
>
RX / A(+)
tX / A (+)
>
>
>
>
RX / B(-)
tX / B(-)
TX / A(+)
rX / A(+)
TX / B(-)
rX / B(-)
>
>
>
NMEA 0183-compliant
device
Wiring to a Standard NMEA 0183-compliant Device with 2-way Communication
Wire
Fuse
7.5 A - 42 V
Garmin
GPSMAP 4000/5000 series
chartplotter
Power
cable
NMEA 0183
Cable
+
see table for
wire colors
Battery
10–35 Vdc
-
Wire
Red (power)
Red (power)
Black (pwr gnd)
Black (pwr gnd)
Black (data GND)
Black (data GND)
>
>
RX / A(+)
tX / A(+)
RX / B(-)
tX / B(-)
OR
OR
>
>
TX / A(+)
rX / A(+)
TX / B(-)
rX / B(-)
>
>
NMEA 0183-compliant
device
>
>
Wiring to a Standard NMEA 0183-compliant Device for One-Way Communication
+
Wire
Garmin
GPSMAP 4000/5000 series
chartplotter
Fuse
7.5 A - 42 V
Power
cable
NMEA 0183
Cable
Battery
10–35 Vdc
Wire
see table for
wire colors
Red (power)
Red (power)
Black (pwr gnd)
Black (pwr gnd)
Black (data GND)
Black (data GND)
>
tX / A(+)
>
tX / B(-)
rX
NMEA 0183-compliant
device
>
Unconnected
Wiring to Send Data to a NMEA 0183-compliant Device With a Single Wire TX Connection
+
Wire
Garmin
GPSMAP 4000/5000 series
chartplotter
Fuse
7.5 A - 42 V
Power
cable
NMEA 0183
Cable
>
>
see table for
wire colors
Red (power)
Battery
10–35 Vdc
Wire
Red (power)
Black (pwr gnd)
Black (pwr gnd)
Black (data GND)
Black (data GND)
NMEA 0183-compliant
device
rX / b(-)
rX / a(+)
tX
>
Wiring to Receive Data from a NMEA 0183-compliant Device With a Single Wire RX Connection
GPSMAP 4000/5000 Series Installation Instructions
17
Wiring to an Optional Alarm
The GPSMAP 4000/5000 series chartplotter can be used with a lamp, a horn, or both, to sound or flash an alert when the chartplotter displays a
message. The alarm does not need to be wired for the GPSMAP 4000/5000 chartplotter to function. The alarm circuit switches to a low-voltage
state when the alarm sounds. The maximum current is 100 mA, and a relay is needed to limit the current from the chartplotter to 100 mA. To
select between visual and audible alerts, install a switch.
+
Wire
Color
Battery
10–35 Vdc
-
Fuse
7.5 A - 42 V Red (power)
Garmin
GPSMAP 4000/5000 series
chartplotter
Black (gnd)
Power
cable
Horn
NMEA 0183
Cable
Relay
Yellow (alarm)
Lamp
100 ma max
coil current
Wiring to a lamp, a horn, or both.
Wiring to a DB-9 PC Serial Connector
The GPSMAP 4008/4208/4010/4210/4012/4212/5008/5208/5012/5212 chartplotters can be connected to a PC with a serial port by wiring the
chartplotter to a DB-9 serial connector.
+
Wire
Garmin
GPSMAP 4000/5000 series
chartplotter
Fuse
7.5 A - 42 V
Power
cable
NMEA 0183
Cable
Battery
10–35 Vdc
-
see table for
wire colors
DB-9 Serial
PC Connector
DB-9 pin
numbers
Red (power)
Black (pwr gnd)
pin 5: gnd
Black (data GND)
>
>
>
>
RX / B(-)
RX / A(+)
Pin 3: tX
tX / A(+)
Pin 2: rX
TX / B(-)
Unconnected
>
>
1
2
3
4
5
6
7
8
9
End View
Wiring to a DB-9 Serial PC Connector
18
GPSMAP 4000/5000 Series Installation Instructions
Wiring to a GPS 17 or GPS 17 HVS Antenna
If you already have a Garmin GPS 17 or GPS 17 HVS installed on your boat, you can wire it to the GPSMAP 4000/5000 series chartplotter
instead of installing the included GPS 19x. Wire the existing GPS 17 or GPS 17 HVS antenna to the included 19-pin NMEA 0183 cable as well
as to the power supply for the boat, referring to the diagram below. Use 22 AWG shielded wiring for extended runs of wire to the NMEA 0183
cable or GPS 17 HVS cable. Solder all connections and seal them with heat-shrink tubing.
Note: If you are using more than one Garmin chartplotter over a Garmin Marine Network, do not wire more than one chartplotter to a GPS
antenna. The GPS signal is shared between multiple chartplotters connected to a Garmin Marine Network.
+
Wire
color
Garmin
GPSMAP 4000/5000 series
chartplotter
Battery
10–35 Vdc
-
Wire
color
Fuse
7.5 A - 42 V Red (power)
Red (power)
Black (gnd)
Black (gnd)
Power
cable
Orange (acc. on)
NMEA 0183
Cable
> Green (Data out)
> GREEN/white (data in)
Fuse
1A
GPS 17 or
GPS 17 HVS
antenna
Yellow (on)
Blue (data in)
>
White (data out) >
Wiring to a GPS 17 or GPS 17 HVS Antenna
Marine Video Cable
The included Marine Video 17-pin cable allows input of NTSC (National Television System Committee)/PAL (Phase Alternate Line) composite
video sources, and PC monitor output (4008/4208/4010/4210/5008/5208 = VGA output, 4012/4212/5012/5212/5015/5215 = XGA output).
Marine Video inputs are only available on the chartplotter to which they are attached and will not transmit over the Garmin Marine Network.
➊ and ➋ VIDEO 1 and VIDEO 2 Inputs (RCA connectors) allow input from two separate NTSC/PAL compatible video devices, such as VCR,
DVD, TV, or a video camera. The chartplotter can display one video input at a time or alternate between the two. See the owner’s manual for
details. Sound from a video source must be attached to a separate stereo/audio system. The video output from video devices attaches to the
Video 1 (Black Cable) or Video 2 (Gray Cable) RCA connectors.
➌ Use the PC monitor output (HD 15-pin) connector for remote viewing of the chartplotter display on a computer monitor. The remote monitor
must be capable of at least VGA resolution and have multi-sync capability.
Note
➊
➌
➋
Pin 2
Pin 1
➋
Pin 7
Pin 17
➊
Marine Video Cable
End View
GPSMAP 4000/5000 Series Installation Instructions
➌
Connector
Pin
Function
RCA-1
Center
2
Video 1 in (black jacket)
RCA-1 Outer
6
Video 1 in, gnd
RCA-2
Center
11
Video 2 in (gray jacket)
RCA-2 Outer
15
Video 2 in, gnd
HD-15 Pin 1
1
VGA, analog-red
HD-15 Pin 2
4
VGA, analog-green
HD-15 Pin 3
3
VGA, analog-blue
HD-15 Pin 5
13
VGA, analog, gnd
HD-15 Pin 6
8
VGA, analog-red, gnd
HD-15 Pin 7
8
VGA, analog-green, gnd
HD-15 Pin 8
8
VGA, analog-blue, gnd
HD-15 Pin 10
13
VGA, sync-Gnd
HD-15 Pin 13
7
VGA, H-sync
HD-15 Pin 14
12
VGA, V-sync
HD-15 Pin
shell
9
VGA, overall shield
19
Making the Final Connections to the GPSMAP 4000/5000 Series Chartplotter
After the power cable and the GPS antenna (as well as any optional Garmin Marine Network devices, NMEA 0183 devices, NMEA 2000
connections, or video connections) are wired to the boat, the cables must be connected to the GPSMAP 4000/5000 series chartplotter.
There are seven connectors on the back of the chartplotter, one for power, three for Garmin Marine Network devices, one for the NMEA 0183
cable, one for a NMEA 2000 cable, and one for the marine video cable.
To attach the power cable, the NMEA 0183 cable, and the marine video cable, carefully press the cable into the correct port on the back of the
chartplotter until it is firmly seated. Do not force the cable, because this may damage the pins. After the cable is seated, turn the locking ring
clockwise until it stops.
To attach a Garmin Marine Network cable or a NMEA 2000 Micro-connector cable, carefully press the cable into the correct port on the back of
the chartplotter until it is firmly seated. Do not force the cable, because this may damage the pins. After the cable is seated, turn the locking
ring clockwise until it is tight. Be careful not to overtighten the locking ring.
NMEA 2000 cable
Micro-connector
Power cable connector
Garmin Marine Network
connectors
Marine video cable
connector
NMEA 0183 cable
connector
GPSMAP 4000/5000 Series Connectors
Updating the Chartplotter Software
Your GPSMAP 4000/5000 series chartplotter may contain a software update SD card. If so, follow the instructions provided with the card.
If a software update SD card is not included, visit www.garmin.com to make sure your chartplotter software is up-to-date. To determine the
version of software on your chartplotter, select or touch Configure > System > System Information.
20
GPSMAP 4000/5000 Series Installation Instructions
Specifications
Specification
Devices
Measurement
Size
4008, 4208
7 in. H × 11 13/64 in. W × 4 13/64 in. D (176.9 × 284.4 × 106 mm)
4010, 4210
8 29/32 in. H × 13 13/32 in. W × 4 1/8 in. D (226.9 × 340.4 × 105.1 mm)
4012, 4212
9 1/2 in. H × 14 51/64 in. W × 4 1/8 in. D (240.5 × 375 × 105.1 mm)
5008, 5208
6 51/64 in. H × 10 3/32 in. W × 4 11/64 in. D (173.5 × 256 × 105.9 mm)
5012, 5212
9 15/32 in. H × 13 in. W × 4 45/64 in. D (240.5 × 330 × 119.2 mm)
5015, 5215
11 21/32 in. H × 15 35/64 in. W × 5 21/32 in. D (295.8 × 394.9 × 143.8 mm)
4008, 4208
6 lb. (2.7 kg)
4010, 4210
8 lb. (3.6 kg)
4012, 4212
10 lb. (4.5 kg)
5008, 5208
6 lb. (2.7 kg)
5012, 5212
10 lb. (4.5 kg)
5015, 5215
12 lb. (5.4 kg)
4008, 4208
5 11/64 in. H × 6 27/32 in. W (131.4 × 174 mm)
4010, 4210
6 11/32 in. H × 8 7/16 in. W (161.4 × 214.2 mm)
4012, 4212
7 19/64 in. H × 9 11/16 in. W (184.3 × 245.8 mm)
5008, 5208
5 in. H × 6 47/64 in. W (128.2 × 170.9 mm)
5012, 5212
7 7/64 in. H × 9 19/64 in. W (180.49 × 235.97 mm)
5015, 5215
8 63/64 in. H × 11 31/32 in. W (228.1 × 304.1 mm)
Case
All models
Fully Gasketed, high-impact plastic and aluminum alloy, waterproof to IEC 529-IPX
Temp. Range
All models
from 5°F to 131°F (from -15°C to 55°C)
Weight
Display
Compass Safe 4008, 4208, 5008, 5208
Distance
4012, 4212, 5012, 5212
31 1/2 in. (80 cm)
39 3/8 in. (1 m)
4010, 4210
31 1/2 in. (80 cm)
5015, 5215
23 5/8 in. (60 cm)
Power
Specification
Devices
Measurement
Source
All models
10 - 35 Vdc
Usage
4008, 4208
35 W max. at 10 Vdc
4010, 4210
40 W max. at 10 Vdc
4012, 4212
40 W max. at 10 Vdc
5008, 5208
35 W max. at 10 Vdc
5012, 5212
40 W max. at 10 Vdc
Fuse
5015, 5215
60 W max. at 10 Vdc
All models
7.5 A, 42 V fast-acting
NMEA 2000 Load Equivalency Number (LEN) All models
2
NMEA 2000 Unit Draw
75 mA max.
All models
GPSMAP 4000/5000 Series Installation Instructions
21
NMEA 2000 PGN Information
Receive
22
Transmit
059392
ISO Acknowledgment
059392
ISO Acknowledgment
059904
ISO Request
059904
ISO Request
060928
ISO Address Claim
060928
ISO Address Claim
126208
NMEA - Command/Request/Acknowledge Group Function
126208
NMEA - Command/Request/Acknowledge Group Function
126464
Transmit/Receive PGN List Group Function
126464
Transmit/Receive PGN List Group Function
126992
System Time
126996
Product Information
126996
Product Information
127250
Vessel Heading
127250
Vessel Heading
128259
Speed - Water Referenced
127489
Engine Parameters - Dynamic
128267
Water Depth
127488
Engine Parameters - Rapid Update
129025
Position - Rapid Update
127505
Fluid Level
129026
COG & SOG - Rapid Update
128259
Speed - Water Referenced
129029
GNSS Position Data
128267
Water Depth
129540
GNSS Sats in View
129025
Position - Rapid Update
130306
Wind Data
129026
COG & SOG - Rapid Update
130312
Temperature
129029
GNSS Position Data
129539
GNSS DOPs
129540
GNSS Sats in View
130306
Wind Data
130310
Environmental Parameters
130311
Environmental Parameters
130312
Temperature
130313
Humidity
130314
Actual Pressure
GPSMAP 4000/5000 series
chartplotters are NMEA 2000 certified.
GPSMAP 4000/5000 Series Installation Instructions
GPSMAP 4000/5000 Series Installation Instructions
23
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web
site at www.garmin.com.
© 2012 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK
Garmin Corporation
No. 68, Zhangshu 2nd Road, Xizhi Dist., New Taipei City, 221, Taiwan (R.O.C.)
www.garmin.com
Download PDF

advertising