Owner`s manual | Garmin 2006C GPS Receiver User Manual

owner’s manual
EDGE® 200
GPS-ENABLED CYCLING COMPUTER
July 2011
190-01368-00_0A
Printed in Taiwan
Getting Started
About the Battery
 warning
Always consult your physician before
you begin or modify any exercise
program. See the Important Safety
and Product Information guide in the
product box for product warnings and
other important information.
 warning
This product contains a lithium-ion
battery. See the Important Safety and
Product Information guide in the
product box for product warnings and
other important information.
When using your Edge® the first time,
complete the following tasks:
1.
2.
3.
4.
5.
6.
7.
Charge the Edge (page 2).
Install the Edge (page 3).
Turn on the Edge (page 4).
Acquire satellites (page 6).
Go for a ride (page 6).
Save your ride (page 6).
Get Garmin Connect™ software
(page 7).
8. Transfer history to your computer
(page 8).
2
The Edge is powered by a built-in,
lithium-ion battery that you can
recharge using the AC charger or the
USB cable included in the product box.
NOTE: The Edge will not charge when
outside the temperature range of 32°F
to 122°F (0°C to 50°C).
Charging the Edge
notice
To prevent corrosion, thoroughly
dry the mini-USB port, the weather
cap, and the surrounding area before
charging or connecting to a computer.
Edge 200 Owner’s Manual
note: To connect the Edge to your
computer using the USB cable, see
page 8.
1. Plug the AC charger into a standard
wall outlet.
2. Pull up the weather cap from the
mini-USB port ➊.
➊
3. Plug the small end of the AC
charger into the mini-USB port.
4. Charge the Edge for at least three
hours before you begin using it.
A fully charged battery can run for
up to 14 hours before it must be
recharged.
Installing the Edge
For the best GPS reception, position
the bike mount so the front of the Edge
is oriented toward the sky. You can
install the bike mount on the stem or
the handlebars.
1. Select a suitable and secure location
to mount the Edge where it does not
interfere with safe operation of your
bike.
2. Place the rubber disk ➊ on the back
of the bike mount ➋.
The rubber tabs align with the back
of the bike mount so it stays in
place.
➍
➋
➊
➌
Edge 200 Owner’s Manual
3
3. Place the bike mount on the bike
stem.
4. Attach the bike mount securely
using the two bands ➌.
5. Align the tabs on the back of the
Edge with the bike mount notches
➍.
6. Press down slightly and turn the
Edge clockwise until it locks into
place.
Releasing the Edge
1. Turn the Edge counterclockwise to
unlock the device.
2. Lift the Edge off the mount.
Turning on the Edge
Press
.
Configuring the Edge
The first time you turn on the Edge,
you are prompted to configure system
settings and user profile settings.
• Follow the on-screen instructions to
complete the initial setup.
• Select ▲ or ▼ to view choices
and change the default selection.
• Select to make a selection.
4
Edge 200 Owner’s Manual
Keys
Each Edge key has multiple functions.
Key
Description
Select to turn the
device on and off,
cancel, or return to the
previous menu.
Select to start and stop
the timer.
Select to create a new
lap.
Select to scroll through
training data pages.
Hold on any page
to return to the main
menu.
Edge 200 Owner’s Manual
5
Acquiring Satellite
Signals
It may take 30 to 60 seconds to acquire
signals.
1. Go outdoors to an open area.
2. Make sure that the front of the Edge
is oriented toward the sky.
3. Wait while the Edge searches for
satellites.
The time of day and date are set
automatically.
1. Select Ride.
2. Select Start to start the timer.
History is only recorded while the
timer is running.
3. After completing your ride, select
.
Training Indoors
You can turn off GPS when you are
training indoors.
1. Select Ride > Start.
A message appears asking if you
want to use the device indoors.
2. Select Yes.
GPS automatically turns back on when
indoor training is complete.
Saving Your Ride Data
Going for a Ride
Select Save to save your ride data
and reset the timer.
Before you can record history, you
must acquire satellite signals (page 6).
6
Edge 200 Owner’s Manual
Back to Start
You can navigate back to the start of
your ride. The timer must be on to use
back to start.
Garmin recommends that you use
Garmin Connect (page 7) to create
courses. You can then transfer the
courses to your Edge.
1. Select Ride > Start.
2. After completing your ride, select
.
3. Select Back to Start > Start.
Creating a Course with Your
Edge
Before you can create a course, you
must have history with GPS track data
saved to the Edge.
Using Free Software
1. Select Courses.
2. Select a ride > Create.
Garmin Connect is web-based software
for storing and analyzing your ride
data.
1. Go to www.garminconnect.com.
2. Select Getting Started.
3. Follow the on-screen instructions.
Courses
Starting a Course
You must have saved a course to start
a course.
1. Select Courses.
2. Select a course from the list >
Start.
Courses allow you to train using a
previously recorded activity. You can
follow the course trying to match or
exceed previously set goals.
Edge 200 Owner’s Manual
7
History
The Edge can save at least 130
hours of ride data with typical use.
When the Edge memory is full, a
message appears. The Edge does not
automatically delete or overwrite your
history. See page 9 to learn how to
delete history.
Upload your history (page 8) to
Garmin Connect periodically to keep
track of all of your ride data.
History includes time, distance,
calories, average speed, maximum
speed, ascent and descent, and detailed
lap information.
note: History is not recorded while
the timer is stopped or paused.
8
Viewing History
1. Select History.
2. Select an option:
• Last Ride
• Longest Ride
• Fastest Ride
• All Rides
• Odometer
3. Use ▲ and ▼ to scroll through
your activities.
note: To see lap data, select
Options > Laps.
Transferring History to
Your Computer
1. Connect the USB cable to a USB
port on your computer.
2. Pull up the weather cap from the
mini-USB port ➊.
Edge 200 Owner’s Manual
3. Select Yes.
Deleting History
➊
3. Plug the small end of the USB
cable into the mini-USB port.
4. Go to www.garminconnect.com.
5. Follow the on-screen instructions.
Viewing the Odometer
Select History > Odometer to
view the accumulated ride distance
and time.
Resetting the Odometer
1. Select History > Odometer >
Reset.
2. Select an option:
• Select Trip to reset current trip
data
• Select Reset All to reset all
odometer data.
Edge 200 Owner’s Manual
After you have transferred your history
to your computer, you may want to
delete the history from your Edge.
1.
2.
3.
4.
Select History.
Select an option.
Select a ride.
Select Options > Delete Ride.
Alerts
You can use Edge alerts to train toward
specific distance, time, and calorie
goals.
Using Distance, Time, and
Calorie Alerts
1. Select Settings > Alerts.
2. Select Distance, Time, or Calorie.
3. Turn on the alert.
4. Enter a time, distance, or calorie
amount.
9
5. Go for a ride.
Each time you reach the alert amount,
the Edge beeps and displays a message.
Auto Lap
Using Auto Lap by Position
You can use Auto Lap® to
automatically mark the lap at a specific
position. This feature is helpful for
comparing your performance over
different parts of a ride (for example, a
long climb or training sprints).
1. Select Settings > Auto Lap.
2. Select By Position.
3. Select an option:
• Select Lap Only to trigger the
lap counter each time you select
and each time you pass any
of those locations again.
• Select Start And Lap to trigger
the lap counter at the GPS
location where you select
and at any location during the
ride where you select .
• Select Mark And Lap to trigger
the lap counter at a specific GPS
location marked before the ride
and at any location during the
ride where you select .
4. Go for a ride.
Note: During courses, use the By
Position option to trigger laps at all of
the lap positions saved in the course.
Using Auto Lap by Distance
You can use Auto Lap to automatically
mark a lap at a specific distance. This
feature is helpful for comparing your
performance over different parts of a
ride (for example, every 10 miles or 40
kilometers).
1. Select Settings > Auto Lap.
2. Select By Distance.
10
Edge 200 Owner’s Manual
3. Enter a value.
4. Select Save.
Using Auto Pause
You can use Auto Pause® to pause the
timer automatically when you stop
moving or when your speed drops
below a specified value. This feature is
helpful if your ride includes stop lights
or other places where you need to slow
down or stop.
Note: The paused time is not saved
with your history data.
1. Select Settings > Auto Pause.
2. Select an option:
• Select Off.
• Select When Stopped to pause
the timer automatically when
you stop moving.
• Select Custom Speed to pause
the timer automatically when
your speed drops below a
specified value.
Edge 200 Owner’s Manual
3. Go for a ride.
Using Auto Scroll
Use the auto scroll feature to
automatically cycle through all of the
training data pages while the timer is
running.
1. Select Settings > Auto Scroll.
2. Select a display speed: Slow,
Medium, or Fast.
3. Go for a ride.
The training data pages scroll
automatically.
11
Changing the Start Notice
This feature automatically detects
when your Edge has acquired satellites
and is moving. It is a reminder to start
the timer so you can record your ride
data.
1. Select Settings > Start Notice.
2. Select an option:
• Select Off.
• Select Once.
• Select Repeat to change the
amount of time to delay the
reminder.
Changing Your User
Profile Settings
The Edge uses information that you
enter about yourself to calculate
accurate ride data.
1. Select Settings > User Profile to
update gender, birth year, weight,
and height.
12
2. Follow the on-screen instructions.
Data Management
You can use the Edge as a USB mass
storage device.
note: The Edge is not compatible
with Windows® 95, 98, Me, or NT. It is
also not compatible with Mac® OS 10.3
and earlier.
Deleting Files
NOTICE
Your device memory contains
important system files that should not
be deleted.
1. Connect the Edge to your computer
using the USB cable (page 8).
2. Open the Garmin drive or volume.
3. Select the file.
4. Select the Delete key on your
keyboard.
Edge 200 Owner’s Manual
System Settings
Specifications
Changing the Backlight
1. Select Settings > System >
Display.
2. Adjust the backlight brightness and
the backlight duration.
Tip: Use a short backlight setting
to conserve battery power.
notice
The Edge is waterproof to IEC
Standard 60529 IPX7. It can withstand
immersion in 1 meter of water for
30 minutes. Prolonged submersion
can cause damage to the unit. After
submersion, be certain to wipe dry
and air dry the unit before using or
charging.
Changing the Audible Tones
1. Select Settings > System > Tones.
2. Turn the tones for keys and
messages on or off.
Changing the Auto Power
Down Setting
This feature automatically turns the
Edge off after 15 minutes of inactivity.
1. Select Settings > System > Power
Down.
2. Select On or Off.
Edge 200 Owner’s Manual
Edge Specifications
Water
resistance
IPX7
Computer
interface
USB 2.0 full speed
Battery life
14 hours, typical
usage*
Operating
temperature
range
From -4°F to 140°F
(from -20°C to 60°C)
13
Edge Specifications
Bike Mount Specifications
Charging
temperature
range
Bands
(O-rings)
From 32°F to 122°F
(from 0°C to 50°C)
*The actual battery life of a fully
charged battery depends on how
much time you use GPS and the
backlight. Exposure to extremely cold
temperatures will also reduce battery
life.
Bike Mount Specifications
Physical size
(W × H × D)
1.5 × 1.5 × 0.36 in.
(37.8 × 37.8 × 9.2
mm)
Two sizes:
• 1.3 × 1.5 × 0.9 in.
AS568-125
• 1.7 × 1.9 × 0.9 in.
AS568-131
Note: Use EPDM
(Ethylene Propylene
Diene Monomer)
replacement bands
only.
Go to http://buy
.garmin.com, or
contact your Garmin
dealer.
Weight
0.28 oz. (7.9 g)
(including
bands and
rubber spacer
pad)
14
Edge 200 Owner’s Manual
Troubleshooting
Registering Your Device
Help us better support you by
completing our online registration
today:
• Go to http://my.garmin.com.
• Keep the original sales receipt, or a
photocopy, in a safe place.
Resetting the Device
If the keys stop responding, you may
need to reset the device.
Hold
for 10 seconds.
Clearing User Data
1. Turn off the Edge.
2. Hold and simultaneously.
3. Select Yes to clear all user data.
Note: This deletes all
user‑entered information, but it
does not delete your history.
Edge 200 Owner’s Manual
Updating the Software
1. Connect the Edge to your computer
using the USB cable (page 8).
2. Go to www.garminconnect.com.
If there is new software available,
Garmin Connect alerts you to
update the software.
3. Follow the on-screen instructions.
Caring for Your Device
notice
Do not store the device where
prolonged exposure to extreme
temperatures can occur, because it can
cause permanent damage.
Avoid chemical cleaners and solvents
that can damage plastic components.
Cleaning the Device
1. Use a cloth dampened with a mild
detergent solution.
2. Wipe it dry.
15
www.garmin.com
913-397-8200
1-800-800-1020
00 358 19 311 001
815 69 555
0808 2380000
+44 (0) 870.8501241
00 33 1 5517 81 89
00800 4412 454
+44 2380 662 915
1-866-429-9296
0180 5 / 42 76 46 - 880
0180 5 / 42 76 46 - 550
00 35 1214 447 460
43 (0) 3133 3181 0
00 39 02 3669 9699
00 902 00 70 97
00 32 2672 5254
0800-0233937
00 46 7744 52020
00 45 4810 5050
www.garmin.com/support
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park
Southampton, Hampshire, SO40 9LR UK
Garmin Corporation
No. 68, Zhangshu 2nd Road, Xizhi Dist.
New Taipei City, 221, Taiwan (R.O.C.)
© 2011 Garmin Ltd. or its subsidiaries
Garmin®, the Garmin logo, Edge®, Auto Lap®, and Auto Pause®
are trademarks of Garmin Ltd. or its subsidiaries, registered in
the USA and other countries. Garmin Connect™ is a trademark
of Garmin Ltd. or its subsidiaries. These trademarks may not
be used without the express permission of Garmin. Windows®
is a registered trademark of Microsoft Corporation in the United
States and/or other countries. Mac® is a trademark of Apple
Computer, Inc., registered in the U.S. and other countries.
Download PDF

advertising