Garmin 520 Two-Way Radio User Manual

Rino 520/530
®
2-way radio & GPS
owner’s manual
© Copyright 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street
Olathe, Kansas 66062, U.S.A.
Tel. 913/397.8200 or 800/800.1020
Fax 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle
Abbey Park Industrial Estate
Romsey, SO51 9DL, U.K.
Tel. 44/0870.8501241
Fax 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated,
downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants
permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy
of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this
copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make
changes in the content without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site
(www.garmin.com) for current updates and supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, AutoLocate®, MapSource®, TracBack®, BlueChart®, and Rino® are registered trademarks of Garmin Ltd. or its subsidiaries and may
not be used without the express permission of Garmin.
March 2006
Part Number 190-00548-00 Rev. B
Printed in Taiwan
INTRODUCTION
INTRODUCTION
Thank you for choosing the Garmin® Rino® 520 or the
Rino® 530 (Radio Integrated with Navigation for the
Outdoors). To get the most from your new Rino 520 or
Rino 530, read through the Quick Start Guide first, then
this Owner’s Manual to understand all of the operating
features.
The Quick Start Guide describes the process of
navigating the Main Pages and the Option Menus, along
with some basic unit operations to familiarize you with
your new Rino 520/530 right out of the box. Read the
Quick Start Guide first.
This manual is organized into the following sections:
The Introduction section provides FCC, safety, warranty,
and product registration information, as well as the Table
of Contents.
The Getting Started section provides basic information
about the Rino 520/530.
Rino® 520/530 Owner’s Manual
The Unit Operation section provides information on
each of the Main Pages, listed in the same order as
viewed on the unit. The section for each page provides
an overview that describes how it functions, and stepby-step instructions for using the page and its features. It
also includes an overview of some additional features and
step-by-step instructions for using those features.
The Appendix includes additional information about the
Rino 520/530
The Index provides keywords and the pages on which
they appear.
Note that: Significant differences between the Rino
520 and Rino 530 features are noted throughout the
Quick Start Guide and the Owner’s Manual. The Rino
530 contains all of the features of the Rino 520 with the
addition of a seven channel NOAA weather receiver with
weather alert, an electronic compass, and barometric
pressure altimeter.
i
INTRODUCTION > WARNINGS AND CAUTIONS
Warnings and Cautions
The GPS system is operated by the United States government
which is solely responsible for its accuracy and maintenance. The
system is subject to changes which could affect the accuracy and
performance of all GPS equipment. Although the Garmin Rino
520/530 is a precision electronic NAVigation AID (NAVAID), any
NAVAID can be misused or misinterpreted and, therefore, become
unsafe.
The electronic chart is an aid to navigation and is designed to
facilitate the use of authorized government charts, not replace
them. Only official government charts and notices to mariners
contain all information needed for safe navigation—and, as
always, the user is responsible for their prudent use.
Use the Rino 520/530 at your own risk. To reduce the risk of
unsafe operation, carefully review and understand all aspects
of this Owner’s Manual. When in actual use, carefully compare
indications from the Rino 520/530 to all available navigation
sources, including the information from other NAVAIDs, visual
sightings, charts, etc. For safety, always resolve any discrepancies
before continuing navigation.
WARNING: The Rino 520/530 contains a lithium-ion
rechargeable battery pack. The battery used in this device may
present a risk of fire or chemical burn if mistreated. Do not
ii
disassemble, heat above 140°F (60°C), or incinerate.
WARNING: If the original battery pack must be replaced, dispose
of the used battery properly. Contact your local waste disposal
department for information on proper disposal of lithium-ion
batteries. Keep used batteries away from children. Do not
disassemble or dispose of batteries in fire.
MAP DATA INFORMATION: One of the goals of Garmin
is to provide customers with the most complete and accurate
cartography that is available to us at a reasonable cost. We use a
combination of governmental and private data sources, which we
identify (as required) in product literature and copyright messages
displayed to the consumer. Virtually all data sources contain
inaccurate or incomplete data to some degree. This is particularly
true outside the United States, where complete and accurate digital
data is either not available or prohibitively expensive.
CAUTION: IT IS THE USER’S RESPONSIBILITY TO
USE THIS PRODUCT PRUDENTLY. THIS PRODUCT IS
INTENDED TO BE USED ONLY AS A NAVIGATIONAL AID
AND MUST NOT BE USED FOR ANY PURPOSE REQUIRING
PRECISE MEASUREMENT OF DIRECTION, DISTANCE,
LOCATION, OR TOPOGRAPHY.
Rino® 520/530 Owner’s Manual
INTRODUCTION > WARNINGS AND CAUTIONS
IMPORTANT: READ THIS INFORMATION BEFORE
USING YOUR RINO:
Exposure to Radio Frequency Signals—Your wireless handheld
radio is a low power radio transmitter and receiver. When it is
on, it receives and also sends out radio frequency (RF) signals.
In August 1996, The Federal Communications Commissions
(FCC) adopted RF exposure guidelines with safety levels for
handheld wireless radios. Those guidelines are consistent with
safety standards previously set by both U.S. and international
standards bodies: American National Standards Institute (ANSI)
IEEE. C95.1-1992; National Council on Radiation Protection
and Measurements (NCRP) Report 86; International Commission
on Non-Ionizing Radiation Protection (ICNIRP) 1996. Those
standards were based on comprehensive and periodic evaluations
of the relevant scientific literature. For example, over 130
scientists, engineers, and physicians from universities, government
health agencies, and industry reviewed the available body of
research to develop the ANSI Standard (C95.1). The design of your
radio complies with the FCC guidelines (and those standards).
Rino® 520/530 Owner’s Manual
For body-worn and face-held operation, this radio demonstrates
compliance and meets the FCC RF exposure guidelines for
uncontrolled exposure (general population) when used with
approved accessories supplied with or designed for this product.
Use of other accessories may not ensure compliance with FCC RF
exposure guidelines.
Antenna Care—Use only the supplied antenna. Unauthorized
antennas, modifications, or attachments could damage the radio
and may violate FCC regulations. Do not use any radio that has
a damaged antenna, because if it comes into contact with your
skin, a minor burn can result.
Electronic Devices—Most modern electronic equipment is
shielded from RF signals. However, certain equipment may not be
shielded against the RF signals from your wireless radio.
Pacemakers—The Health Industry Manufacturers Association
recommends that a minimum separation of six inches (6”) be
maintained between a handheld wireless radio and a pacemaker
to avoid potential interference with the pacemaker. These
recommendations are consistent with the independent research by
and recommendations of Wireless Technology Research. Persons
with pacemakers should ALWAYS keep the radio more than six
inches from their pacemaker when the radio is turned on, should
not carry the radio in a breast pocket, should use the ear opposite
iii
INTRODUCTION > WARNINGS AND CAUTIONS
the pacemaker to minimize the potential for interference, and
should turn the radio off immediately if you have any reason to
suspect that interference is taking place.
Commercial Aircraft—Many commercial airlines prohibit the
use of FRS/GMRS radios on board. Switch OFF your radio before
boarding an aircraft or check the airline rules.
Hearing Aids—Some digital wireless radios may interfere with
some hearing aids. In the event of such interference, you may want
to consult your hearing aid manufacturer to discuss alternatives.
Blasting Areas—To avoid interfering with blasting operations,
turn your radio OFF when in a “blasting area” or in areas posted:
“Turn off two-way radio.” Obey all signs and instructions.
Other Medical Devices—If you use any other personal medical
device, consult the manufacturer of your device to determine if it is
adequately shielded from external RF energy. Your physician may
be able to assist you in obtaining this information.
Potentially Explosive Atmospheres—Turn your radio OFF
and do not remove your battery when you are in any area with a
potentially explosive atmosphere. Obey all signs and instructions.
Sparks from your battery in such areas could cause an explosion or
fire resulting in bodily injury or even death.
Turn your radio OFF in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health
care facilities may be using equipment that could be sensitive to
external RF energy.
Vehicles—RF signals may affect improperly installed or
inadequately shielded electronic systems in motor vehicles. Check
with the manufacturer or its representative regarding your vehicle.
You should also consult the manufacturer of any equipment that
has been added to your vehicle.
Areas with a potentially explosive atmosphere are often, but not
always clearly marked. They include fueling areas such as gasoline
stations, below deck on boats, fuel or chemical transfer or storage
facilities; vehicles using liquefied petroleum gas (such as propane
or butane); areas where the air contains chemicals or particles,
such as grain, dust, or metal powders; and any other area where
you would normally be advised to turn off your vehicle engine.
Posted Facilities—Turn your radio OFF in any facility where
posted notices so require.
iv
Rino® 520/530 Owner’s Manual
INTRODUCTION > WARNINGS AND CAUTIONS
WARNING: This product, its packaging, and its components
contain chemicals known to the State of California to cause cancer,
birth defects, or reproductive harm. This Notice is being provided
in accordance with California’s Proposition 65. If you have any
questions or would like additional information, please refer to our
Web site at http://www.garmin.com/prop65.
Because the Garmin Rino 520/530 can be used for vehicular
navigation, important safety considerations must be followed.
Please read and observe the following instructions.
WARNING: For use in vehicles, it is the sole responsibility of
the owner/operator of a vehicle with the Rino 520/530 installed to
place and secure the device so it will not interfere with the vehicle
operating controls and safety devices, obstruct the driver’s view
of driving conditions, or cause personal injury in the event of an
accident.
Do Not Mount
Where Driver’s
Field of Vision is
Blocked
Do Not Place
Unsecured
on the Vehicle
Dash
Do Not Mount in Front of an Airbag Field
of Deployment
Rino® 520/530 Owner’s Manual
v
INTRODUCTION > TABLE OF CONTENTS
Introduction.............................................................i
Getting to Know Your Rino 520/530 .....................1
Front of the Rino 520/530 ........................................ 2
Back of the Rino 520/530 ......................................... 3
Main Display Pages .................................................. 4
Operating the Rino 520/530 ..................................... 5
Status Bar Overview ................................................ 6
Unit Operation........................................................7
vi
Radio Page ................................................................ 7
Initializing the Rino 520/530 ......................................... 7
Using Name and Symbol Fields .................................... 8
Setting the Channel and Code ..................................... 10
Adjusting the Volume and Squelch Level: .................. 11
Scanning and Monitoring ............................................ 12
Radio Page Option Menu ............................................ 13
Setup Radio ............................................................ 14
Setup Tones ............................................................ 16
Use Weather Radio .................................................... 17
Use Weather Alert .................................................. 17
Turn Radio/GPS On/Off ........................................ 18
Status Window ............................................................. 18
GPS Status ............................................................. 18
Radio Transmission/Reception Status ................... 18
Using the Rino 520/530 Radio Features ............... 20
Peer-to-Peer Positioning .............................................. 20
New Contact Page Overview ....................................... 20
Sending a Location ...................................................... 23
Map Page................................................................. 24
Map Page Options ....................................................... 26
Using the Pan Map Option .......................................... 27
Programming the Data Fields ...................................... 28
Setting up the Map ....................................................... 29
Measuring Distance ..................................................... 31
Compass Page........................................................ 32
Using the Compass Page ............................................. 32
Compass Page Options ................................................ 34
Using Sight ‘N Go ...................................................... 35
Calibrating the Compass .............................................. 35
Altimeter Page ....................................................... 37
Altimeter Page Options ............................................... 38
Viewing Pressure/Elevation Plots ................................ 39
Adjusting the Zoom Ranges ........................................ 39
Pan Plot ........................................................................ 40
Resetting Data.............................................................. 40
Calibrating the Altimeter ............................................. 41
Programming Data Fields ............................................ 41
Main Menu Page .....................................................
42
®
Rino 520/530 Owner’s Manual
INTRODUCTION > TABLE OF CONTENTS
Satellite Page .......................................................... 43
Sky View Graphic ........................................................ 43
WAAS .......................................................................... 44
Satellite Strength.......................................................... 44
Satellite Page Options .................................................. 45
Trip Computer Page ............................................... 47
Trip Computer Page Options ....................................... 47
Waypoints ...............................................................48
Mark Waypoint Page ................................................... 48
Creating Waypoints ..................................................... 49
Averaging a Waypoint ................................................. 50
Projecting a Waypoint.................................................. 50
Editing a Waypoint ...................................................... 50
Find ..........................................................................52
Finding a Waypoint...................................................... 53
Finding a Geocache ..................................................... 54
Finding a Contact......................................................... 55
Finding a City .............................................................. 56
Finding an Exit ............................................................ 57
Finding a Point of Interest ........................................... 58
Finding an Address or Intersection .............................. 60
Recent Finds ................................................................ 62
Using Go To Navigation .............................................. 63
Rino® 520/530 Owner’s Manual
Tracks Page ............................................................ 64
Using the TracBack Feature ........................................ 65
Setting up the Track Log ............................................. 67
Using Track Profiles ................................................... 67
Routes Page............................................................ 68
Editing a Route ............................................................ 69
Adding or Editing from the Route Map Page .............. 72
Setting Up Routing Methods ....................................... 73
Navigating a Route ...................................................... 74
Using the Turn-By-Turn Active Route Page ............... 74
Highway Page ........................................................ 75
Setup Pages ............................................................ 76
System Setup Page....................................................... 76
Radio Setup Page ......................................................... 77
Display Setup Page ...................................................... 77
Tones Setup Page ......................................................... 78
Page Sequence Setup ................................................... 78
Map Setup Page ........................................................... 78
Routing Setup Page ..................................................... 79
Geocache Setup ........................................................... 79
Marine Setup................................................................ 79
Time Setup Page .......................................................... 80
Units Setup Page .......................................................... 81
vii
INTRODUCTION > TABLE OF CONTENTS
LORAN TD Format ............................................... 81
Heading Setup Page ..................................................... 83
Calibration Setup Page ............................................... 83
Altimeter Setup ............................................................ 84
Welcome Page Setup ................................................... 84
Interface Setup Page .................................................... 85
Proximity Waypoints .............................................. 87
Calendar .................................................................. 88
Alarm Clock ............................................................ 90
Calculator ................................................................ 91
Stopwatch ............................................................... 92
Sun & Moon ............................................................ 93
Hunt & Fish ............................................................. 94
Games .....................................................................95
Memory Race .............................................................. 95
Geko Smak .................................................................. 95
Nibbons ........................................................................ 96
Gekoids ........................................................................ 96
Beast Hunt ................................................................... 96
Assimilation ................................................................. 97
Clothesline ................................................................... 97
Waypoint Bomber ........................................................ 97
About FRS/GMRS Radio ........................................ 98
Specifications ....................................................... 100
Standard Accessories Provided with the Unit ... 102
Optional Accessories ........................................... 102
Installing Accessories.......................................... 102
Transferring MapSource Data ............................. 103
GPS Troubleshooting Guide ............................... 105
Radio Frequency Charts ...................................... 106
Data Field Definitions........................................... 109
Interface Information............................................ 111
FCC Compliance Information .............................. 112
FCC Licensing Information ................................. 113
Limited Warranty .................................................. 114
Software License Agreement .............................. 116
Product Registration ............................................ 116
Index ...................................................................117
Appendix ..............................................................98
viii
Rino® 520/530 Owner’s Manual
.GETTING STARTED.
GETTING TO KNOW YOUR RINO
520/530
The Rino 520/530 (Radio Integrated with Navigation for
the Outdoors) is a FRS/GMRS radio with a 12 channel
GPS receiver. It has integrated radio functionality to
provide two-way communications for up to two miles
using FRS (Family Radio Service) channels. The Rino
520/530 also provides 15 high-performance GMRS
(General Mobile Radio Service) channels and 8 GMRS
repeater channels (U.S. versions only) for communication
up to 14 miles. GMRS channels are limited to 2 watts of
power when used in Canada. GMRS repeater channels
are not approved for use by the Canadian government, so
they are disabled on Rino 520/530 units sold in Canada.
The Rino 520/530 has three user-selectable GMRS power
levels: 0.5 W, 2.0 W, and 5.0 W (USA only). Keep in
mind that FRS channels only transmit at 0.5 W. The Rino
520/530 also has a rechargeable lithium-ion battery pack
with charger. Be certain to fully charge the lithium-ion
battery while attached to the Rino 520/530 prior to the
Rino® 520/530 Owner’s Manual
first use to ensure accurate battery capacity reporting.
Follow the charging instructions contained in the Rino
Quick Start Guide
If you wish, you can purchase a spare lithium-ion battery
pack or an optional alkaline battery pack with transmit
power limited to 2.0 W.
The unit contains built-in cartography of a North
American basemap that includes Interstate and State
Highways and Exit Information. The Rino uses compatible
MapSource®map data software (not included). The Rino
520/530 can display up to 56 MB of a variety of detailed
map data. Some of the mapping options that are compatible
with the Rino 520/530 include City Select, MetroGuide,
Topo, Fishing Hot Spots, and BlueChart® data. Check your
local dealer or the Garmin Web site (www.garmin.com) for
a complete listing of MapSource products.
The Rino 520/530 is waterproof to IPX7 standards and is
designed for rugged use. Garmin’s user-friendly interface
allows you to start navigating almost immediately.
1
GETTING STARTED
Front of the Rino 520/530
Power button:
• Press and hold to turn the unit On/Off
• Press to adjust contrast and backlighting
Call button:
• Press to send out Call Tone
• Sends position when released
(if enabled)
Talk button:
• Press and hold to talk
• Sends position when released
(if enabled)
Page/Quit button:
• Press to cycle through main pages
• Used to quit or escape menu items
Volume (V) button:
• Press to open volume/squelch control
• Press and hold to mute/unmute the
speaker
Speaker
2
TFT Display
Thumb Stick
• Press In to enter highlighted options and to confirm
messages
• Move Up, Down, Right or Left to
move through lists, highlight fields,
on-screen buttons, icons, enter data,
or move the map panning arrow
• Press In and hold to display Shortcuts Menu.
Zoom/Map (Z) button:
• From the Map Page, press to open Zoom control
window
• From any other page, press to display Map Page
and press again to open Zoom control
• Press and hold to turn the electronic compass
On/Off (Rino 530 only)
Microphone:
• Hold unit 3-4 inches away when talking
Rino® 520/530 Owner’s Manual
GETTING STARTED
Back of the Rino 520/530
GPS Antenna
Upper - Wrist Strap Attachment Point
2-way FRS/GMRS Antenna
Belt Clip/Bike/Auto Mount Connector
Battery Pack Locking D-Ring
Mini USB Port with Weather Cap
Headset Connector with Weather Cap
Battery Charger Contacts
Lower - Wrist Strap Attachment Point
Rino® 520/530 Owner’s Manual
Lithium-Ion Battery Pack
Lithium-Ion Battery Information
• Completely charge with the battery attached to the Rino prior to use
to ensure accurate capacity reporting. Refer to the Quick Start Guide.
• Avoid prolonged exposure to direct sunlight and high temperatures
as this can reduce useful battery life. See “Specifications”
• Do not store a fully discharged battery for long periods of time. This
may prevent the battery from recharging.
• See the section on Warnings and Precautions for instructions on
proper disposal of batteries no longer capable of being recharged.
• If the battery capacity gauge becomes inaccurate; fully discharge
the battery by leaving the unit On, in normal mode, until it shuts off.
Then fully charge the battery while attached to the unit.
3
GETTING STARTED
Main Display Pages
All of the information you need to operate the Rino 520/530 can be found on five default main pages (four for the Rino
520). Simply press and release the Page/Quit button to cycle through the Radio Page, Map Page, Active Route Page*,
Compass Page, Altimeter Page (Rino 530 only), and Main Menu Page. You can also access the Main Pages by pressing the
on-screen Main Page button . Customize the Main Page sequence by using the Page Sequence Setup (see page 78).
Follow
Road
Off
Road
Active Route Page
*Active Route page displays in the main page sequence only
when navigating a route or when on a Go To..
Radio Page
Map Page
There are two types of Active Route Pages: one with TurnBy-Turn directions when following roads and one with a list of
points when navigating off road.
The Altimeter Page is
displayed only for the
Rino 530.
Main Menu
4
Altimeter Page
Compass Page
Rino® 520/530 Owner’s Manual
GETTING STARTED
Operating the Rino 520/530
For best results, you should initialize the GPS receiver in
your Rino 520/530 unit before you use it the first time.
See page 7 for instructions on initializing the unit. The
compass and altimeter contained in the Rino 530 should
also be calibrated. Refer to the “Calibrating the Compass”
and “Calibrating the Altimeter” sections.
To use the Thumb Stick:
•
•
•
Press In to enter highlighted options and to
confirm messages.
Move Up, Down, Right or Left
to move through lists, highlight
fields, on-screen buttons, icons,
enter data, or move the map
panning arrow.
Press In and hold to display Shortcuts Menu.
To use the Page Option Menu:
1. Highlight the Option Menu on-screen button
the top of the display screen and then press
the Thumb Stick In to open the menu.
Rino® 520/530 Owner’s Manual
at
2. Highlight the desired menu option and press the
Thumb Stick In to activate the option.
3. To close without making a selection, move the
Thumb Stick to the Right.
To Close a feature or setting page:
1. Highlight the Close button at the top of the
page and press theThumb Stick In to return to
the previous page, or press the Page/Quit button.
Shortcuts Menu
The Shortcuts Menu, accessed by holding the Thumb
Stick In, provides quick access to frequently used
features and the Lock Keys option.
To lock/unlock the buttons (keys):
1. Press and hold the Thumb Stick
In to access the Shortcuts Menu.
Highlight Lock Keys and press
the Thumb Stick In. Only the Call
and the Press To Talk buttons are
functional.
2. To unlock, press and hold the Page/Quit button
until “Keylock Disabled” is displayed (about 5
seconds).
5
GETTING STARTED
Status Bar Overview
As you move around any of the Main Pages, the current
page’s title briefly displays (3 seconds) and then is
replaced by the Status Bar. The Status Bar displays
current settings and operational icons and contains the
Main Page
and Page Option Menu
buttons.
The available icons are:
Battery Level
Using External Power
Receiving Radio signal
Transmitting Radio signal
Radio On
Peer-To-Peer On/Location Ready to Send
Keylock On
Alarm Clock On
Speaker Muted
Weather Alert On (Rino 530 only)
You can adjust the backlight level by pressing the
POWER key and releasing, then tap the POWER key
or press the Thumb Stick Up/Down to cycle through
the levels of backlight adjustment. See page 77 for
information on changing the display colors and backlight
timeout and brightness levels. Backlighting is Off when
you power up the unit. When On, it uses a significant
amount of battery power.
Pop-Up Messages
Whenever a significant event in the operation of the unit
occurs, an on-screen message displays to advise you of
the occurrence. In each case, the condition is described
and often a remedy provided. Pressing the Thumb Stick
acknowledges the message and closes the window.
On-Screen Message
GPS On, 3D Position Fix
6
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
UNIT OPERATION
Radio Page
The Radio Page is the first of the default Main Pages.
This page provides the user interface for FRS (Family
Radio Service) and GMRS (General Mobile Radio
Service) radio operations. Garmin Rino units work with
third party FRS/GMRS radios using standard FRS/GMRS
frequencies. To take advantage of all of the Rino features,
communication with other Rinos is necessary.
The Radio Page also provides access to the Weather
Radio (available in Rino 530 only), which provides
a constant update of current weather conditions by
receiving NOAA weather broadcasts for your area. The
Weather Alert feature further enhances the Weather Radio
by automatically notifying you of any weather alerts,
even when the Weather Radio is not is use and the FRS/
GMRS radio is not transmitting or receiving an audio
transmission. These features are helpful while outdoors or
planning any trips or activities.
Rino® 520/530 Owner’s Manual
Radio Page
Initializing the Rino 520/530
To take full advantage of the Rino 520/530 features,
the GPS receiver must be initialized. The initialization
process allows the Rino 520/530 to receive and store
satellite information and begin using the satellites for
navigation. Initialization is automatic and should only
take a few minutes. If this is the first time the unit is used
or if you have moved more than 600 miles from your last
used location, initialization may take up to 5 minutes.
7
UNIT OPERATION > RADIO PAGE
To initialize the unit:
1. Take the Rino 520/530 outside where there is an
unobstructed view of the sky and turn it on.
2. The unit begins to search for satellite signals. A
Satellite Signal graph is displayed on the Radio
page or you can get more detailed information by
accessing the Satellite Page from the Main Menu.
3. The first time you initialize your Rino it could take
up to five minutes. When the GPS is initialized and
ready for navigation, three or more green GPS
signal bars are displayed.
If for some reason the unit is not able to gather the
necessary satellite information, refer to the GPS Troubleshooting Chart in the Appendix.
Using Name and Symbol Fields
The Name field allows you to enter a name that appears
on other Rino units as you communicate with them. You
may enter a name using a combination of up to 10 letters,
numbers, or spaces. The Symbol field allows you to choose
a face icon from a list to further personalize your identity.
8
Name Field
Symbol Field
Radio Status
GPS Status
Face options
To enter a name:
1. Using the Thumb Stick, highlight the Name field.
Press the Thumb Stick In to activate the field and
display the keyboard.
2. Move the Thumb Stick Up, Down, Left, or Right
to highlight the Clear field, then press the Thumb
Stick In to clear the default Name.
3. To enter a new name, use the Thumb Stick to
move the cursor to the desired character (letter,
number, or a space). Press the Thumb Stick In to
select that highlighted character. Choose Back to
delete the character to the left of the cursor. You
may enter up to 10 characters for your name.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Entering a name
with the on-screen
keyboard
4. When you have entered your new name, use the
Thumb Stick to highlight OK and then press the
Thumb Stick In.
To change the user symbol:
1. Using the Thumb Stick, highlight the face symbol
on the left of the Name field. Press the Thumb
Stick In to show a list of available face icons.
2. Move the Thumb Stick Up or Down to scroll
through the selections. Because not all the
selections can fit in the window, a slider bar on the
right side indicates your current position in the list.
Rino® 520/530 Owner’s Manual
Changing the
user symbol
TIP: Hold the Thumb Stick Up or Down to scroll
through the list more quickly. Once you reach the end
of the list, you can wrap back to the top or bottom by
releasing the Thumb Stick then pressing in the same
direction again. This same method may also be used
on other selection windows.
3. Once you have highlighted the desired icon, press
the Thumb Stick In to change the symbol.
9
UNIT OPERATION > RADIO PAGE
Setting the Channel and Code
The Rino 520/530 has a total of 22 channels (not
including GMRS repeater channels) and 38 codes to
select from using the Channel and Code fields. Channels
1–7 and 15-22 are GMRS channels, 8-14 are FRS
channels, and 15R–22R are GMRS repeater channels
(repeater channels are available on U.S. units only and
are disabled by default). To communicate with other Rino
and FRS/GMRS users, you must be on the same channel
and code. Garmin Rino units work with 3rd party FRS/
GMRS radios, provided the other radios use standard
FRS/GMRS frequencies. A chart of Rino frequencies may
be found in the “Appendix.”
Squelch codes allow you to hear calls from only specific
persons. Thirty-eight (38) Codes (called Continuous
Tone Controlled Squelch System or CTCSS) allow
your Rino 520/530 to ignore unwanted calls from other
persons using the same channel. Simply select the same
code (number) as selected by the other person(s) with
which you plan to communicate.
10
Select from FRS 8–14, GMRS 1-7 & 15–22,
and 15R–22R GMRS repeater channels (with
Repeater Channels enabled).
NOTE: Codes do not cause your conversation to be
private. They only allow you to filter out other users
on the same channel, so you only hear the radios you
want to hear. Codes on are not a scrambling system!
Refer to the section on Voice Scramble operation.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Setting the code to 0 (code off) allows you to hear all
activity on the selected channel, but you must be set to
the same code as the other person(s) to transmit back. See
the “Appendix” for a table listing all of the 38 Codes and
their frequencies.
As you change channels, the Rino 520/530 remembers
the last channel/code combination that you were using.
For example, you may set the unit channel to 5 and code
to 21, then change the channel to 8 and code to 2. If you
change the channel back to 5, the code changes back to
its previous setting of 21. See the “Appendix” for more
information on FRS/GMRS and its operational aspects.
Choose from 38 codes. Setting
the unit to zero will allow you to
hear all transmissions on that
channel, but you must be on the
same code to radio back.
To change the Channel and/or Code:
1. Using the Thumb Stick, highlight the Channel or
Code field and then press the Thumb Stick In to
show a list of available channels/codes.
2. Move the Thumb Stick Up or Down to scroll
through the selections. Because not all the items
fit in the window, a slider bar on the right side
indicates your current position in the list.
3. Highlight the selection, press the Thumb Stick In.
Adjusting the Volume and Squelch Level:
1. Press the Volume Control (V) button to display
the Volume/Squelch Level Control window.
2. Move the Thumb Stick Up or Down to adjust the
volume level.
3. Use the Thumb Stick to set the squelch level by
moving the slider all the way to the Left to unmute
the background noise (weak signals that you don’t
want to hear). Then slowly
move it to the Right until the
background noise stops. The
squelch is set.
Volume/Squelch Adjustment
Rino® 520/530 Owner’s Manual
11
UNIT OPERATION > RADIO PAGE
Scanning and Monitoring
The Scan option allows you to scan through the available
channels for activity. As the unit scans and detects
activity on a channel, it pauses on that channel/code for
a few seconds, then continues scanning. If you transmit
at that time you will be on that channel. When the Rino
520/530 is scanning and it receives an incoming signal,
the Rino 520/530 automatically decodes the Code used
by the incoming signal. The Rino 520/530 then uses that
Code when it transmits back to that unit. However, if you
transmit when the scan has not paused, the transmission
uses the channel set before scanning.
You may use the Set Scanlist option to pick which
channels/codes to scan. Scanning through all channels
can take time: Selecting only specific channels/codes
decreases the scan time and helps prevent the chances
of missing a transmission. The Scanlist also has Option
Menu choices to Scan Current Codes or Scan All Codes.
Choosing Scan Current Codes scans only the Channel and
Code combination in memory.
12
The Monitor option lets you listen to a single channel for
all activity, including static and weak signals. The Rino
requires the user to adjust the squelch for a frequency
to filter out unwanted noise. Using the Monitor option
temporarily turns off the squelch, allowing you to hear
the open channel. If you see an “Activity...” message,
there is activity on your selected channel, but the
incoming signal does not match the Code your unit is
using. You may choose to monitor a channel if you want
to hear all the activity on a channel.
To scan or monitor a channel(s):
1. Using the Thumb Stick, highlight the Scan or
Monitor button and then press the Thumb Stick
In. Scan starts searching through the available
channels. Monitor opens the channel to listen to
any radio transmissions on that channel.
2. To stop using either option, highlight the button
with the Thumb Stick and press In.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
4. To Scan Current Codes, highlight the Option
Menu and press the Thumb Stick In. Choose the
desired setting and press the Thumb Stick In.
The Code field is blank when the unit is scanning or monitoring
channels until a signal is received and it pauses.
To set up a Scanlist:
1. Using the Thumb Stick, highlight the Option Menu
button and press In. Highlight Setup Scanlist and
press the Thumb Stick In.
2. To add/remove a channel from the list, highlight
the channel and press the Thumb Stick In to
add/remove the check mark in front of the name.
Only channels that are checked will be scanned.
3. To select all channels or clear all channels,
highlight either the Select All or Clear All buttons
and press the Thumb Stick In.
Scanlist Page
Radio Page Option Menu
The Radio Page Option Menu allows you to customize
aspects of your Rino 520/530, such as setting up the
radio, programming call and ring tones, and setting up a
scanlist.
Rino 530 option only
Radio Page Option Menu
Rino® 520/530 Owner’s Manual
13
UNIT OPERATION > RADIO PAGE
Setup Radio
The Setup Radio option displays the Radio Setup Page.
This page determines how the radio functions and enables
you to adjust the radio operation to your needs. The
following options are available:
Setup Radio Page
Send Location—Enables/disables the peer-to-peer
positioning feature. See the “Peer-to-Peer” section for
more on this feature.
Allow Polling—Enables/disables your Rino 520/530’s
ability to respond to a polling request from another Rino.
GMRS Power—Use this to set the power level used
to transmit GMRS channels (1-7, 15-22 and repeater
14
channels 15R-22R, if applicable) 1/2 watt is used for
FRS channels 7-15. If the battery is too low to support
the higher power levels, it automatically decreases the
transmit power and sends a notification message.
Scramble—Adds a level of privacy to your
conversations. When On, the voice transmission sounds
garbled to other non-scrambled Rino units, as well as
other third party radios.
NOTE: When Scramble is set to On, in order for
peer-to-peer and Send Location features to work, the
receiving radio must have Scramble enabled also.
Repeater Channel—Use this option to turn On/Off
GMRS repeater channels 15R–22R. Repeater channels
use repeaters, when available, to enable communication
around obstacles that normally block transmission and
can increase tranmission distance. GMRS repeater
channels are not available in Rino units sold in Canada.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Weather Alert—When Weather Alert is enabled (See
Weather Radio section), the receiver is set to look for
weather alert tones either only on the current channel or
on all channels .
is recommended for most environments, but it may be
necessary to adjust the level to achieve the desired voice
trigger level. You will hear yourself talking in the headset
when transmitting successfully using VOX.
Headset Type—Allows you to choose which accessory
headset or microphone you are using with the unit, or
have the unit automatically detect the type. If you use
more than one type of headset or microphone, you need
to set the unit to Ask When Detected before changing
accessories.
Microphone Sensitivity—Allows you to set the
sensitivity of the internal microphone and the sensitivity
of a headset microphone. When selected, a sensitivity
adjustment slider displays. Adjusting the sensitivity
requries the assistance of another radio user to advise of
the voice quality received while adjusting the slider.
NOTE: If the headset has a PTT (Push to Talk)
button, it must be pressed for the unit to detect the
headset.
VOX Level—Controls the sensitivity level of any
Voice Operated Transmission (VOX) accessory.
VOX accessories allow you to use the unit handsfree. A lower VOX setting is recommended for quiet
environments while a higher VOX setting should be
used in noisy environments. Setting the VOX level to 5
Rino® 520/530 Owner’s Manual
Mic Adjustment Slider
15
UNIT OPERATION > RADIO PAGE
Setup Tones
Call Tone—When the Call button
is pressed, an attention tone is
transmitted. This option allows you
to choose one of 10 tones.
Roger Tone—When the Talk
button is released, a tone is sent to Setup Tones Page
signify the end of the transmission. This option allows
you to choose one of four tones, or set the tone to Off.
Ring Tone—When an incoming transmission is received,
an attention tone will sound. This option allows you to
choose one of 10 tones or set the tone to Off. The Ring
tone will not sound again until there has been 45 seconds
of radio inactivity.
Vibrate—Choose from On or Off to have the unit
vibrate when an incoming transmission is received. Once
received, the unit will not vibrate again until there has
been 45 seconds of radio inactivity. The unit also vibrates
at Power On when set to do so.
16
Message Beep—Choose from 19 options or Off to have
the unit emit a tone when a message or note is received.
Key Beep—Choose from four tones or Off to emit a tone
when a key is pressed.
Power Beep—Enable or disable the tone the unit makes
when it is turned on and off.
Turn Warning (Early)—Choose from 19 tones or Off to
signal an upcoming turn on a route.
Turn Warning (Final)—Choose from 19 tones or Off to
signal the final turn on a route.
A “Set Quiet Mode” is available to mute all tones using
the Option Menu.
Setup Scanlist
Refer to “Scanning and
Monitoring” for complete
information about this feature
and the options in
this page.
Setup Scanlist Page
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Use Weather Radio
Available for the Rino 530 only, the Weather Radio
provides a constant update of the weather conditions. The
Weather Alert feature further enhances the Weather Radio
by automatically detecting any weather alert tones if you
are not actively transmitting or receiving with the radio.
To access the Weather Radio, select the Weather button
and press the Thumb Stick In or select the Radio Page
Option Menu button. Press the Thumb Stick In when
Use Weather Radio is highlighted to turn on the weather
radio. You can also access the Weather Radio through the
Shortcuts Menu.
When the Weather Radio is on, a “Ready To Receive
Weather” message displays if no signal is present or the
squelch is set too high. A “Receiving Weather” message
is displayed if weather is being received, if squelch is too
low, or monitor is on. The Weather Radio has a separate
squelch setting from the FRS/GMRS radio. Refer to Page
11 for instructions on setting the squelch for weather
radio.
Rino® 520/530 Owner’s Manual
Change the Weather Radio channel in the same manner as
changing the FRS/GMRS radio channel. There are seven
Weather Radio channels (1 through 7) available.
Radio Page with
Weather Radio On
Changing the Weather
Radio Channel
Selecting the “Seek” button increments the radio to the
next active weather channel. Selecting the “Monitor”
button monitors the selected channel for activity.
Use Weather Alert
When the radio is on, Enable Weather Alert is located
at the bottom of the Radio Page Option Menu. Press
the Thumb Stick In when Enable Weather Alert is
highlighted to turn it on. You can then turn the Weather
Radio off and continue FRS/GMRS radio operations.
17
UNIT OPERATION > RADIO PAGE
When a Weather Alert tone is detected, the Rino 520/530
automatically turns on the Weather Radio and broadcasts
the Weather Alert if you are not actively transmitting or
receiving on the radio. The volume changes to 3/4 the
maximum when a Weather Alert is broadcast. Select
Disable Weather Alert to turn off this feature.
To turn the weather radio off, press the Thumb Stick
In when Use FRS/GMRS Radio is highlighted. This
switches the Rino 520/530 back over to the FRS/GMRS
radio operation. Weather Alert is disabled whenever the
FRS/GMRS and Weather Radio is turned off.
Turn Radio/GPS On/Off
Press the Thumb Stick In on either of these two options
to toggle them from on to off. For example, to turn GPS
Off, press the Thumb Stick In when Turn GPS Off is
highlighted.
18
Status Window
The Status Window on the bottom half of the Radio Page
shows current GPS and radio status, and radio actions. As
you operate the unit, the graphics change depending on
what actions you are taking and the unit settings.
GPS Status
The GPS signal bars indicate the strength of satellite
arrays overhead. More bars mean more satellites in view.
As the unit collects satellite information, the satellite
signal bars increase to indicate a 3D position fix. The
more satellite signal bars, the better your position
fix. Three or more green bars are required for GPS
navigation.
Radio Transmission/Reception Status
As the radio transmits and receives, a variety of messages
appear to indicate the type and status of the transmission
or reception.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > RADIO PAGE
Radio Page Status Indicators
The Radio Page status bar displays icons and the status window displays messages and icons to describe current
operating conditions, depending on what you are doing. See below for explaination of messages and icons.
Message
Radio Status
A signal is being received, but doesn’t match the code.
The 2-way Radio is turned Off
FRS Channel is selected and
you can transmit
GMRS Channel is selected
and you can transmit
Radio feature Off
Transmit Power at 1/2 watt
You are receiving a transmission on the
selected channel
Transmit Power at 2 watts
Set to a weather channel and waiting to
receive weather broadcast
Receiving a weather broadcast
Transmit Power at 5 watts
GPS Status Status Bar
GPS receiver Off
Radio On
Acquiring Satellites
Radio
Receiving
Weakest Signal
Radio
Transmitting
2D GPS Location
3D GPS Location
You are transmitting on an FRS channel
You are transmitting on an GMRS channel
Your position (current location) is being sent
Rino® 520/530 Owner’s Manual
Peer-to-peer On
Position Ready
to transmit
3D GPS Location
Strongest Signal
GPS On Position Ready
Weather Alert
On
19
UNIT OPERATION > USING THE RINO 520/530 RADIO FEATURES
Using the Rino 520/530 Radio
Features
Your Rino 520/530 unit provides many features to
enhance your radio experience, such as transmitting
your location or any location and receiving contact
information. This section reviews some of the advanced
radio features. Refer to the “Features” section for
information on all of the features of the Rino 520/530.
Peer-to-Peer Positioning
The Rino 520/530’s most unique feature is being able to
send its location to another Rino, which is called Peer-toPeer positioning. With peer-to-peer positioning enabled
(see the “Setup Radio” section) and a GPS position,
whenever you press and release either the Call button or
the Talk button, the Rino 520/530 automatically sends out
its location. This information is available to all other Rino
users that are monitoring the same channel and squelch
code. This feature allows you to track the movement
of other Rino users and even navigate to their location.
Locations may only be sent once every 30 seconds due
20
to FCC restrictions. Your Rino 520/530 can respond to
polling requests from other units more frequently.
To transmit your location to other Rino users:
1. Enable Send Location (see “Setup Radio”).
2. Press and release either the Talk or Call button.
A bright flag on the Status Bar indicates the unit
is ready to transmit its position. A dimmed flag is
waiting for the 30 second delay to expire.
New Contact Page Overview
The first time that a signal is received from another Rino
user, a New Contact page is displayed. From the New
Contact page you can show their location on your Map,
Go To their location, or select OK to add it to the Contact
List. Press the Page/Quit button to disregard the contact.
Name and
Symbol
New
Contact Page
Contact Information
Field
Rino® 520/530 Owner’s Manual
UNIT OPERATION > USING THE RINO 520/530 RADIO FEATURES
The Rino 520/530 can manage up to 50 contacts at any
time. Each time you receive a signal from a contact, your
map is updated showing their new position. A Track Log
of their movement is created and shown on your map
(see the “Track Logs” section). After a contact has been
established, a “<contact name> Updated” message briefly
appears at the bottom of your display each time the
contact updates.
All contacts are listed on the Find Contact Page and are
also displayed in the Contact Bar on the Map Page (see
the “Map Page” section). Contacts behave like waypoints
and count towards the 500 maximum waypoint total.
If the contact did not have a GPS location on the last
transmission, the last known position appears overlayed
by a question mark in the Location field. To view the
contact details (such as Direction and Distance from
Current Location, Elevation, Location, and Notes that
have up to 30 characters), use the Thumb Stick to move
to the next data field to add or change information.
Rino® 520/530 Owner’s Manual
Use the Thumb Stick to view or edit
different contact data.
To accept a new contact:
1. When a new contact is received, the New Contact
page automatically appears.
2. Highlight OK and press the Thumb Stick In. If you
do not select OK, the contact is not saved.
21
UNIT OPERATION > USING THE RINO 520/530 RADIO FEATURES
To review a contact and contact details:
1. From the Map Page, highlight the desired contact
on the Contact Bar and press the Thumb Stick In.
As you highlight the contacts on the Contact Bar,
the Map page centers the map on that contact and
display its name, direction and distance near the
top of the screen.
Or
1. Press the Thumb Stick In and hold it until the
Shortcuts Menu is displayed. Highlight Find and
press the Thumb Stick In.
2. Highlight Contacts and press the Thumb
Stick In.
3. From the Contacts List, select the desired contact
and press the Thumb Stick In.
2. For Notes, highlight the field and press the Thumb
Stick In to start entering data, up to 30 characters.
For other fields, highlight the field and press the
Thumb Stick In to start changing the data.
3. Highlight OK and press the Thumb Stick In when
done.
Contacts List
To change contact details:
1. The Elevation, Position, and Note fields may be
manually edited. Select the desired field and press
the Thumb Stick In.
Contact Details Page
22
Rino® 520/530 Owner’s Manual
UNIT OPERATION > USING THE RINO 520/530 RADIO FEATURES
Sending a Location
Another feature is the ability to send a specific location
to other Rino users. This comes in handy when you are
trying to round-up the group or you just want to meet at a
specific location. You may send any point found from the
Find menu. If the unit needs to wait until 30 seconds have
elapsed since the last position transmission, a “Waiting to
send location...” message appears until the unit is able to
transmit. If a location is sent more than once, a number is
automatically added to the end of the name (for example:
CAMP, CAMP 1, CAMP 2, etc.).
To send a location:
1. Press the Thumb Stick In and hold it until the
Shortcuts Menu is displayed.
2. Highlight Find and press the Thumb
Stick In.
3. Highlight the desired category and press the
Thumb Stick In. ( For the Contacts List, select the
desired contact and press the Thumb Stick In.)
4. Depending on which category you select, highlight
the desired item and press the Thumb Stick In to
display the Information page for that item.
5. From the Information Page, highlight the Option
Menu button in the upper right corner of the page
and press the Thumb Stick In.
6. Highlight Send Location and press the Thumb
Stick In again. The unit now sends the point to the
other Rino users on your channel/squelch code.
To send a location, highlight the Option
Menu from the Waypoint Review Page,
select Send Location, and press In.
Rino® 520/530 Owner’s Manual
23
UNIT OPERATION > MAP PAGE
Map Page
In many instances the map displays an Accuracy Circle
surrounding the Position Icon. The Rino 520/530 uses
both map resolution and GPS accuracy in defining your
location to a point within the circle. The smaller the
circle, the more accurate your location.
The map displays geographic details such as rivers, lakes,
highways, and towns. The map can display a higher level
of detail than the basemap provided with the unit (i.e.
residential streets, parks, etc.), if Garmin MapSource
data has been downloaded to the unit using a CD-ROM
mapping program. When using MapSource data, the word
“mapsource” displays below the map scale whenever you
zoom in to view map details.
When using the Pan Map feature (accessed from the Map
Page Option Menu), a small outline arrow (Map Pointer)
can be moved about the page to highlight and identify
map items or to scroll the map to view areas not shown
on the display screen.
The Map Page displays your present position and
direction of movement using a triangular Position Icon
that is shown on the map. As you travel the map display
leaves a “trail” (track log) of your movements.
At the top of the Map Page, you can choose to show
either the Contact Bar, Data Fields, Guidance Text,
or only the Map. As you highlight the contacts on the
Contact Bar, the Map Page centers the map on that
contact and displays its name, direction, and distance.
Highlighting the Contact on the Map Page and pressing
the Call button polls the contact.
24
Option Menu and Main
Page Menu Buttons
Status Bar
Accuracy Circle
Contact Bar
Map Scale
Position Icon
Rino® 520/530 Owner’s Manual
UNIT OPERATION > MAP PAGE
To view a Contact from the Map Page:
1. Highlight the Contact icon using the Thumb
Stick. As you highlight the contacts on the
Contact Bar, the Map page centers the map on
that contact and displays its name, direction, and
distance near the top of the screen.
2. Press the Thumb Stick In to view the details of
the Contact.
3. Press the Thumb Stick to the Left or Right to recenter the map on your current position.
The scale can be changed from 20 feet to 500 miles. A
lower zoom scale displays less area but more map detail,
while a higher zoom scale shows you a larger area with
less map detail. The Thumb Stick and Z (Zoom) button
on the front right of the unit allow you to zoom in and
out on the map. Press the Z (Zoom) button from any page
(other than the Map Page) to open the Map Page.
To change scales on the Map Page:
1. Press the Z (Zoom) button to open the Zoom
window.
2. Use the Thumb Stick and Z (Zoom) button to
change the map scale in order to show more map
area with less detail or less map area with more
detail.
Press and hold Up or Down on the Thumb Stick
to zoom the map scale rapidly. Press the Thumb
Stick In or to any direction to close the Zoom
window.
The map scale in the lower left hand side of the display is
shown in units of measurement selected in the Units field
of the Unit Setup Page (accessed
through the Main Menu Setup
Page). If you zoom in so far that
the resolution of the map data is
exceeded and the appearance of
the map is no longer accurate, the
word, “overzoom” displays just
Up to Zoom Out;
below the map scale.
Down to Zoom In
Rino® 520/530 Owner’s Manual
25
UNIT OPERATION > MAP PAGE
Map Page Options
Map Page options allow a variety of operating and
custom features for your Rino 520/530. The Map Page
options are:
Map Page Option Menu
Pan Map—Allows you to move the Panning Arrow (Map
Pointer) about on the map. Refer to the “Using the Pan
Map Option” section for complete instructions.
Stop Navigation—Quits navigation of a Go To, Route
or Track in progress. When you are not navigating to a
destination, the Stop Navigation option is “grayed out”
and is non-functional.
Show... Data Fields—Displays two, three, or four
navigation data fields, Map Only, and Contacts. Data
fields can be programmed to display various data options.
Guidance Text—Displays guidance information such
as direction to turn at the next intersection, etc. It can
be set for Always Show, Never Show, or Show When
Navigating.
Setup Map—Displays the Setup Map Pages, which
allow you to tailor the map to your requirements such
as changing text size, map orientation, and map detail.
Refer to the “Setting up the Map” section for complete
instructions.
Measure Distance—Displays the distance from one
point on the map to another.
Turn Declutter On—Turns the Declutter feature on to
reduce the amount of map details when zoomed out.
Restore Defaults—Returns the Map Page to the original
factory settings (defaults).
Recalculate—Recalculates the current route.
26
Rino® 520/530 Owner’s Manual
UNIT OPERATION > MAP PAGE
Using the Pan Map Option
The Map Page pan function allows you to display an
arrow used to point at and identify items on the map,
and to move the map in order to view areas beyond the
current viewing area on the display.
The map panning function is activated from the Option
Menu on the Map Page. Use the Thumb Stick to move
the panning arrow (also referred to as the map pointer) in
the desired direction. If the arrow moves to the edge of
the map display, the map also moves to reveal more area.
Whenever you place the panning arrow on a map item,
the name of that item is highlighted. This feature applies
to waypoints, roads, lakes, rivers; nearly everything that
is displayed.
Press the Thumb Stick In to mark the arrow location or
display the map item information page. The Option Menu
allows you to: send the location of that item, project a
waypoint from it, save it as a waypoint, set a proximity
circle around it, add it to a route, or view the Sun &
Moon phase or view Hunt & Fish information from it.
Rino® 520/530 Owner’s Manual
On-screen buttons at the bottom of the page allow you
to Go To the map item, display it on the map or to select
OK and return to the Map Page. Press the Page/Quit
button to stop panning the map.
To Find an item near the map pointer:
1. When using the panning arrow, press and hold the
Thumb Stick In to display the Shortcuts Menu.
2. Select Find to display items. Select the category
you wish to search (waypoints, contacts, etc.). The
Rino 520/530 then searches for the items nearest
the location of the map pointer instead of your
actual location.
Map Page with
Panning Arrow
27
UNIT OPERATION > MAP PAGE
Programming the Data Fields
Select Show... Data Fields to view from two, three, or
four optional Data Fields at the top of the screen that
can be programmed to provide a variety of travel and
navigation information. A list of the choices is shown to
the right. Not all data types are available on every page.
Data Field Options
Thee data field options apply to the Map Page data
fields and the Trip Computer data fields. For definitions
of all data fields used in the Rino 520/530, refer to the
“Appendix.”
To program a data field:
1. Use the Thumb Stick to highlight the data field
and then press In to display the list of data
options.
2. Highlight the desired option and then press the
Thumb Stick In to change the data field type.
Changing Data Fields
Guidance text
The Guidance Text option displays upcoming
intersections, points, or direction to navigate. The three
options are: Always Show, Never Show, and Show When
Navigating.
Selecting Data Fields
28
Rino® 520/530 Owner’s Manual
UNIT OPERATION > MAP PAGE
Setting up the Map
The Setup Map option displays the five Map Setup Pages,
each accessed by an on-screen button.
Sub-Page Buttons
Setup Items
Marine Data Setup
Map Data Setup
Text Setup
3. Press Up or Down on the Thumb Stick to
highlight an item on the list. Press Right to return
to the sub-page buttons.
5. Use the Thumb Stick to highlight the desired
option and then press it In to activate.
6. Press the Page/Quit button or the Close button to
return to the Map Page.
Points Setup
Tracks Setup
General Setup
To use Map Setup options:
1. Select Setup Map from the Options Menu and
then press the Thumb Stick In to display the Map
Setup Page.
2. Press Right or Left on the Thumb Stick to
highlight the desired sub-page button, which
displays the options for that sub-page.
Rino® 520/530 Owner’s Manual
29
UNIT OPERATION > MAP PAGE
General Setup
Orientation—Track Up or North Up;
fixes the top of the map display to the
current track heading or to a north
heading.
Below—Sets the map scale at which
Track Up displays. Above that scale
the map reverts to North Up.
Auto Zoom—On or Off; automatically scales the map to
display both your current location and the next point to
which you are navigating.
Detail—Most, More, Normal, Less, or Least; controls
how much map detail you see. This setting only applies
to a map feature set to Auto. Those features which have
a specified scale or are turned Off are unaffected by this
setting.
Lock on Road—On or Off; available only if MapSource
Data is loaded. When On, the triangle icon locks to the
road that you are traveling.
30
Tracks Setup
Saved Tracks and Track Log—Scale
options; Off, Auto, or 20 ft–500 miles,
sets the maximum scale at which the
feature should appear on the screen.
Some types of data display only at
certain zoom scales.
Track Points—Select the number of track points per
track. Up to 10,000 active Track Points allowed
Go To Line—Bearing to or Course line displayed on a
Go To route.
Map Points Setup
Map Points, User Waypoints, Street
Label, and Land Cover—Off, Auto,
or 20 ft–500 miles, sets the maximum
scale at which that feature should
appear on the screen. Some types of
data display only at specific zoom
scales.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > MAP PAGE
Text Setup
Map Points, user Waypoints, Street
Label, and Land Cover—None,
Small, Medium, or Large; control the
screen size of the name.
Map Information Setup
Show—Check box; check mark
determines if map data is used or not.
Option Menu allows you to choose
to show all, show none, or show
specific MapSource Data. See also the
“Appendix.”
Measuring Distance
To use the Measure Distance option:
1. Select Measure Distance from the Option Menu
and then press the Thumb Stick In to display the
Panning Arrow. Ref displays under the arrow.
2. Use the Thumb Stick to move about on the Map
Page until you reach the point to which you want to
measure. A new Map Pointer field displays showing
the location of the pointer and the direction and
distance from where you began the measuring.
3. To begin measuring from a different point, press
the Thumb Stick In at the desired location.
4. To stop measuring, press the Page/Quit button.
Map Pointer Field
Marine Setup
Show—Options for categories are On,
Off, and Auto.
Rino® 520/530 Owner’s Manual
Measuring distance
31
UNIT OPERATION > COMPASS PAGE
Compass Page
The Compass Page provides active guidance with a
rotating compass ring that shows your course (heading)
while you are moving and a bearing pointer to indicate
the current direction to your destination (bearing) relative
to the course.
The Data Fields at the top of the page provide you with
navigation information. The list of data field choices and
definitions may be found in the “Appendix.”
The Compass Ring functions as a magnetic compass
when you are stationary (Rino 530 only). When you are
moving, the heading is controlled by the GPS receiver
(based upon settings customized in the Heading Setup
Page).
32
Selectable
Data Fields
Bearing Pointer
Compass Ring
NOTE: The Compass on the Rino 530 must be calibrated for the greatest accuracy. Refer to page 36 for
information on calibrating the compass.
Using the Compass Page
The two main components of the Compass Page are the
Bearing Pointer and Compass Ring. The Bearing Pointer
always points directly to the destination, no matter what
your current location might be. The Compass Ring
displays your heading.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > COMPASS PAGE
While you are navigating a route, the bearing pointer
indicates the direction (a bent arrow) of the turn to the
next point in the route as well as the direction to the
current point when you get within 15 seconds Estimated
Time of Arrival of the current point.
For example, if the arrow is pointing straight up, you
are going directly to your destination. If it points any
direction other than up, turn and move towards the
direction the arrow is pointing until it points up, and
then continue in that direction. If you are using the
Course Pointer option instead and you drift away from
the original line of travel to your destination, the Course
Deviation Indicator (CDI) provides graphic indication of
drift (right or left) and displays the distance off course.
When you are not on an active GoTo, Track, or Route
(in other words, not traveling to a recorded destination),
the Compass Ring displays your heading while you are
moving, but the data fields at the top of the page will not
display any destination related data, such as Estimated
Time of Arrival.
Rino® 520/530 Owner’s Manual
CDI Scale
Compass Page with Course
Pointer and Course Deviation
Indicator (CDI) Scale active.
To stop navigating:
1. Highlight the Option Menu button at the top of the
Compass, Highway, or Map Page and press the
Thumb Stick In.
2. Select Stop Navigation, then press the Thumb
Stick In.
33
UNIT OPERATION > COMPASS PAGE
Compass Page Options
Sight ‘N Go—Use the Sight ‘N Go feature to locate a
landmark visually and then lock in a magnetic heading
to it. Rino 530 feature only.
Stop Navigation/Resume Navigation—Cancels/resumes
navigation (“Grayed out” or disabled unless you are
navigating on a Go To, Track, or Route.)
Recalculate—Recalculates the active route.
Bearing Pointer/Course Pointer—Toggles between
Bearing (always directed toward your destination) and
Course (shows amount of correction needed to get back
on course.)
Show Data Fields—Toggles to display data fields on the
right side of the display or removing the data fields
Compass Page Option Menu
To change data fields:
1. Use the Thumb Stick to highlight the desired data
field and then press it In to display the list of data
options.
2. Select the desired option from the list and press
the Thumb Stick In. The list of data field choices
and definitions may be found in the Appendix.
Calibrate Compass—Calibrates the electronic compass.
Follow the on-screen instructions. Rino 530 feature only.
Restore Defaults—Returns options and data field choices
to factory designations.
34
Rino® 520/530 Owner’s Manual
UNIT OPERATION > COMPASS PAGE
Using Sight ‘N Go
Sighting Marks
Available for the Rino 530 only, this feature allows you
visually locate an object and navigate to it.
To use Sight ‘N Go to navigate:
1. Use the Page button to access the Compass
Page and then use the Thumb Stick to access
the Option Menu.
2. Use the Thumb Stick to highlight Sight ‘N Go
and press In. Note that the compass ring with
pointer is in-line with the two sighting marks on
the case.
3. Hold the Rino 530 at eye level and line up the two
sighting marks on the case with a distant object.
Press the Thumb Stick In to Lock Direction.
4. To navigate to your destination, select Set Course
and press the Thumb Stick In. Begin traveling to
your destination using the pointer as a guide.
To view your destination as a waypoint, select
Project Waypoint and press the Thumb Stick In.
To re-sight the destination, press the Thumb Stick
In when Re-Sight is highlighted.
Rino® 520/530 Owner’s Manual
Rino 530 held level
for Sight ‘N Go
Calibrating the Compass
When you first use the Rino 530, the Electronic Compass
must be calibrated outdoors and away from metal
objects. The accuracy of the Electronic Compass is
adversely affected if the unit is not held level or is held
near items that generate magnetic fields, such as cars,
large belt buckles, etc. Recalibration is recommended
after significant environmental changes such as location
changes, temperature fluctuations, switching from
lithium-ion battery power to alkaline or NiCad. etc.
35
UNIT OPERATION > COMPASS PAGE
To calibrate the Electronic Compass:
1. Use the Page button to access the Compass
Page.
2. Use the Thumb Stick to highlight the Option
Menu button and press In.
3. Highlight the Calibrate Compass option and
press the Thumb Stick In.
4. Press the Thumb Stick In to activate the Start
button and then follow on-screen directions for
holding and turning the unit. Hold the unit level
when calibrating the compass.
The “Calibration Successful” message displays
when finished. If a “Calibration Failed” message
displays, repeat the process.
When you manually turn the Compass Off, it stays off
until you manually turn it On again.
To turn the compass on and off:
• Press and hold the Zoom (Z) button. A message
appears on the screen indicating that the compass
has been turned on or off.
Calibrating the compass: Hold the unit face up
and level while slowly rotating it.
The unit displays a “Just Right,” “Too Fast,” or
“Too Slow” message to help you to adjust your
turning speed as needed.
36
Rino® 520/530 Owner’s Manual
UNIT OPERATION > ALTIMETER PAGE
Altimeter Page
Available for the Rino 530 only, the Altimeter Page
provides the current elevation, rate of ascent/descent,
a profile of elevation changes over distance or time, or
a profile of pressure changes over time. The Altimeter
Page’s Option Menu allows you to select from a
variety of display options such as plotting over time,
plotting over distance, displaying the zoom ranges of
measurement, viewing elevation or pressure points, and
resetting data displays. Two user selectable data fields
allow you to display a variety of current and recorded
pressure and elevation related data.
NOTE: To achieve the greatest accuracy, the
Altimeter should be calibrated. Refer to page 41 for
information on calibrating the Altimeter.
The Status Window is located at the bottom of the page
and displays the current elevation and your current rate
of ascent or descent when moving. It can also display the
ambient or the barometric pressure.
Rino® 520/530 Owner’s Manual
The Plot or Profile Field is located in the center of the
page and can be configured to display either elevation or
ambient pressure or barometer plots as selected from the
Altimeter Page Option Menu.
Data Fields at the top of the page are user selectable and
display a variety of recorded or current data.
Data Fields
Status Window
Four types of plots are possible:
• Elevation vs Time
• Elevation vs Distance
• Barometric Pressure* vs Time
• Ambient Pressure* vs Time
* Ambient Pressure is the actual pressure at your location. Barometric
Pressure is the ambient pressure measured relative to sea level.
37
UNIT OPERATION > ALTIMETER PAGE
Altimeter Page Options
The Altimeter Page Option Menu allows you to select
the type of information and how it is to be displayed.
Altimeter Page Options include:
Zoom Ranges—Sets the zoom range for elevation,
distance, or time.
Pan Plot—Allows you to scroll through the collected
data plots to view elevation, time of day, and date a
specific point was created
Reset…—Clears recorded data from the page to begin
recording new data.
Altimeter Page Option Menu
Plot Over Time/Distance—Plots the changes in
elevation over a length of time or over a distance.
When Plot Over Distance is selected, Plot over Time is
displayed in the Option Menu (and vice versa).
Calibrate Altimeter—Increases the accuracy of the
altimeter. You must know your elevation or pressure
to calibrate the altimeter. See page 41 for detailed
instructions on calibration.
Restore Defaults—Returns the Altimeter Page to the
original factory settings (defaults).
View Pressure/Elevation Plot—Displays a record of
changes in barometric pressure or elevation for a set
period of time.
Plot Ambient/Barometer—Changes between plotting
ambient pressure versus time and barometric pressure
versus time.
38
Rino® 520/530 Owner’s Manual
UNIT OPERATION > ALTIMETER PAGE
Viewing Pressure/Elevation Plots
When selecting the View Elevation Plot option, you
can plot a profile of elevation changes that occur as you
navigate over a set distance or period of time. When
you select View Pressure Plot, you can view a record of
changes in the ambient or the barometric pressure for a
set period of time. When one option is active the other
displays on the Altimeter Page Option Menu.
To view elevation or pressure plots:
1. Use the Thumb Stick to highlight the desired
option from the Option Menu and then press In to
display the plot.
2. Adjust time and distance measurement as desired
using the Elevation Plot Zoom Ranges feature
explained below.
3. To clear the plot and start a new one, you must
clear the Track Log.
Rino® 520/530 Owner’s Manual
Adjusting the Zoom Ranges
You can set the Zoom Ranges for elevation, distance, or
time when you display the View Elevation Plot. You may
change the ranges for the horizontal and vertical scales.
To adjust zoom ranges:
1. Select the type of plot you want to display and use
the Thumb Stick to highlight Zoom Ranges from
the Option Menu.
2. Press the Thumb Stick In to display the Zoom
Ranges Page.
3. Move the Thumb Stick Up or Down to adjust the
vertical distance and Left or Right to adjust either
the time or distance. Press In to return to the Plot
Page.
Zoom Range selection
39
UNIT OPERATION > ALTIMETER PAGE
Pan Plot
The Pan Plot option allows you to scroll through the
stored elevation or pressure profile and to view a single
point along the profile. When the pointer is stopped at a
location along the profile, the display shows the elevation,
time of day and date the point was created. The most
recent data is displayed on the right side of the plot.
As the profile moves past the pointer, the status
window at the top of page changes to display the
date, time, and altitude for the point indicated.
Resetting Data
You can reset the elevation data and the maximum
elevation data by selecting the Reset option from the
Altimeter Page Option Menu.
To reset the elevation data and max elevation
fields:
Pan Plot Option Page
To use the Pan Plot option:
1. Use the Thumb Stick to access the Option Menu.
2. Highlight the View Points option and press the
Thumb Stick In to display the View Points Page.
3. Move the Thumb Stick Right or Left to scroll the
profile past the pointer in the center of the page.
40
1. Use the Thumb Stick to highlight the Reset
option from the page Option Menu and press it In
to display the Reset page.
2. Use the Thumb Stick to highlight the elevation
options on the page and then press it In to place a
check mark in the box next to a selected item.
3. Move to the Apply button and press the Thumb
Stick In to reset the data fields.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > ALTIMETER PAGE
Calibrating the Altimeter
Because the Rino 530 relies on the barometric pressure
to determine the elevation and the pressure at any given
elevation can fluctuate, you can calibrate the altimeter
to increase its accuracy. You must know the elevation
(from a map point or other reliable data) or the pressure
(calibrated to sea level - information you can obtain from
the NOAA weather forecasts received on your Rino 530
or other reliable source) for your current location.
At the message asking “Do You Know The Correct
Pressure?” highlight the on-screen Yes button and
press the Thumb Stick In to enter your pressure.
When finished, highlight OK and press it In to
return to the Altimeter Page.
To manually calibrate the altimeter:
1. Use the Thumb Stick to access the Option Menu.
2. Highlight the Calibrate Altimeter option and press
the Thumb Stick to display the Calibration Page.
3. At the message asking “Do You Know The Correct
Elevation?” highlight the on-screen Yes button and
press the Thumb Stick In to enter your elevation.
When finished, highlight OK and press it In to
return to the Altimeter Page. If you don’t know
your current elevation, press No to move to the
pressure calibration page.
Rino® 520/530 Owner’s Manual
Calibrate Altimeter Pages
Programming Data Fields
Two, user-selectable, data fields support this page and can
be programmed to display the data options.
To program a data field:
1. Use the Thumb Stick to highlight the desired data
field and then press it In to select desired data
from the options list.
41
UNIT OPERATION > MAIN MENU PAGE
Main Menu Page
The Main Menu provides access
to additional Rino 520/530 feature
pages. The pages listed below
provide enhancements to Rino
520/530 operation. Press the Page
button to cycle to the Main Menu
or select it from the Main Page
button at the top of each main page. Main Menu Page
Satellite Page—Provides a picture of the satellite signal
tracking and tells you when the unit is ready to navigate.
Trip Computer Page—Provides navigation data.
Mark Waypoint Page—Allows you to mark a waypoint
for your current location or a map pointer location.
Find Menu—Allows you to locate and Go To Waypoints,
Favorite Locations, Cities, Interstate Exits, Points of
Interest, Addresses, and Intersections.
Tracks Page—Provides access to the track log, saved
tracks, and contact tracks.
42
Routes Page—Allows you to create and store routes.
Highway Page—Provides a graphic perspective of your
current route.
Setup Menu—Controls the settings for many of teh units
operating features.
Proximity Page—Activates an alarm for a defined radius
around a specified waypoint.
Calendar—An outdoor calendar with data access and
waypoint association.
Alarm Clock—Allows use of the Rino as an alarm clock.
Calculator—A standard or scientific calculator.
Stopwatch—A multi-featured stopwatch.
Sun & Moon—Sunrise/Sunset times, Moon phases, sun
and moon positoin tables.
Hunt & Fish—A table of best hunting and fishing times
for agiven location and date.
Games—A series of challenging games, some use GPS.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SATELLITE PAGE
Satellite Page
The Satellite Page provides a picture of satellite signal
tracking, tells you when the unit is ready for navigation,
and shows your location coordinates.
To access the Satellite Page:
1. Press the Page button or the Main Page button to
open the Main Menu.
2. In the Main Menu, scroll down and select
Satellite.
Accuracy and Location
Coordinates
Sky View Graphic
The Sky View graphic represents a view looking up at
the sky from your current location showing satellites
and their assigned numbers. The outer ring represents
the horizon around you. The inner ring represents a
view above you at a 45° angle from vertical. The center
represents directly overhead. Signal Strength Bars for
each satellite are shown below the Sky View. Satellites
and their signals appear as hollow shapes until a signal is
received and then they appear darkened in. The stronger
the signal, the taller the signal bar.
90°
Overhead Satellite Map
Inner ring- 45°
above the horizon
Signal Strength Bars
Satellite Page
Rino® 520/530 Owner’s Manual
Center dot - 90°
above the horizon
Outer ring the horizon
45°
43
UNIT OPERATION > SATELLITE PAGE
WAAS
The Wide Area Augmentation System (WAAS) capability
produces a more accurate position fix. When enabled
(GPS set to Normal and WAAS set to Enabled through
the System Setup Page, also the interface must be set
to something other than RTCM mode), this feature
searches for WAAS satellites near your location and
then receives data for correcting differentials in the
GPS satellite signals. WAAS satellite numbers begin
at number 33 and are displayed on the Satellite Page.
When differential correction data has been received for
GPS satellites (numbers 32 or below), a D displays in
the signal bar beneath the skyview. It is helpful to orient
the unit antenna toward the WAAS satellite shown in the
skyview. To learn more about the WAAS System, refer to
the Federal Aviation Administration Web site (http://gps.
faa.gov/).
Because the Rino 520/530 relies on satellite signals to
provide you with navigational guidance, the unit’s view
of the sky determines how fast you achieve navigational
status. GPS signals do not travel through heavy objects
or people: For best results, keep the unit in clear view of
the sky.
WAAS Satellites
Satellite Page using WAAS
Satellite Strength
At least three satellite signals are needed to determine
your location, otherwise the unit displays a “Poor
Satellite Reception” message with four options:
Use with GPS Off—Select this option if you want to turn
GPS off.
44
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SATELLITE PAGE
New Location—Select this option if you have moved
more than 600 hundred miles (from where you last used
the unit).
Restart Search—Select this option if today is not the
date provided.
Continue Acquiring—Select this option if no other option
applies. The unit will attempt to gather GPS signals.
New Location—If you are more than 600 miles (from
where you last used the unit), select the New Location
and then the Use Map options to approximate your
location. This gives the unit reference information and
speeds satellite acquisition. Once a location fix has been
made, this option is grayed out.
GPS Elevation—Allows you to view the elevation at
your current location as calculated by the GPS receiver.
Satellite Page Options
Use With GPS Off—Use this option when you are
indoors, your view of the sky is obstructed, or you want
to save battery power. You can enter data, create routes,
etc., but cannot navigate in this mode.
Track Up/North Up—You can orient the satellite
skyview by selecting ‘Track Up’ (your direction of travel)
or ‘North Up’ (the satellite skyview oriented to the north).
Display Color Options—You have two color options
for displaying the satellite array and signal strength bars,
‘Single’ or ‘Multicolor.’
Rino® 520/530 Owner’s Manual
Satellite Page Option Menu
45
UNIT OPERATION > SATELLITE PAGE
To select the Use With GPS Off option:
1. Use the Thumb Stick to highlight the Option
Menu button at the top of the page and then press
it In.
2. Use the Thumb Stick to highlight the Use With
GPS Off option and then press it In.
The Rino 520/530 stops tracking satellites and
should not be used for navigation. However, the
next time you turn the unit on, it returns to Normal
GPS operation.
To select Track Up or North Up:
1. Use the Thumb Stick to highlight the Option
Menu button at the top of the page and then press
it In to display the Option Menu.
2. Highlight either the Track Up or North Up option
(depending on which is currently in use), and
press the Thumb Stick In to activate.
46
To enter a new location:
1. Use the Thumb Stick to highlight the Option
Menu button at the top of the page and then press
it In.
2. Highlight New Location and press the Thumb
Stick In to display choices of Auto or Use Map.
If you choose Automatic the Rino 520/530
determines your new location automatically.
If you choose Use Map a map page displays with
instructions stating, “Point to your approximate
location and press ENTER”. Use the Thumb Stick
to move the map pointer to your location on the
map and press the Thumb Stick In to enter the
new location.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > TRIP COMPUTER PAGE
Trip Computer Page
The Trip Computer Page by default displays up to
eight different types of navigation data. Choosing Big
Numbers will display three large data fields.
a desired order on the page, you can customize the Trip
Computer Page to meet your navigation needs.
Trip Computer Page Options
The Option Menu allows you to reset the Trip Computer
data when you are ready to start a new trip, choose
between Big or Small Numbers, and Restore Defaults.
Reset—Clears recorded data from the page to begin
recording new data.
Trip Computer Page,
Small Numbers
Trip Computer Page,
Big Numbers
Each data field is selectable and can contain one of many
data information options. The default settings for these
fields are shown in the illustration. The list of data field
choices and definitions may be found in the “Appendix.”
When the data field title is selected, press the Thumb
Stick In to select a new data field choice. By selecting the
information options that you prefer and arranging them in
Rino® 520/530 Owner’s Manual
Big/Small Numbers—Changes the display from eight
small data fields to three large data fields.
Restore Defaults—Returns the Trip Computer Page to
the original factory settings (defaults).
47
UNIT OPERATION > WAYPOINTS
Waypoints
There are numerous ways to create, edit, and use
waypoints. Use the Shortcut Menu, “Mark” from the
Main Menu, Panning from the Map page, the “Save”
option from Map Point Review page, and the “Save as
Waypoint” option on the Contact Review page. The Rino
520/530 can store up to 500 waypoints.
Mark Waypoint Page
The Mark Waypoint Page allows you to mark and record
your current location as a waypoint. It appears with a
graphic name field that displays the assigned number
for that waypoint, a waypoint symbol, a date and time
notation, location coordinates, approximate elevation, and
direction and distance from your current location.
Waypoint Name
Symbol
Waypoint
Details
To mark your current location and open the
Mark Waypoint Page:
1. Press and hold the Thumb Stick In until the
Shortcut Menu opens.
2. Highlight Mark Waypoint and press the Thumb
Stick In to save your current location as a
waypoint. You can also access this page by
highlighting Mark on the Main Menu Page and
pressing the Thumb Stick In.
3. If you do not want to save it as a new waypoint,
highlight the Close button and press the Thumb
Stick In to cancel.
To use Mark Waypoint Page Options:
•
•
•
To change the name of the waypoint, use the
Thumb Stick to highlight the waypoint name field.
To assign an identifying symbol to a waypoint, use
the Thumb Stick to highlight the symbol block just
to the left of the waypoint name.
To view the waypoint on the map, highlight the
Map button and press the Thumb Stick In.
Mark Waypoint Page
48
Rino® 520/530 Owner’s Manual
UNIT OPERATION > WAYPOINTS
Creating Waypoints
To create a waypoint for a
map feature contained in
the Find feature:
1. Access the Find Menu from
the Main Menu and open a
categories list to select the Saving a map feature
desired map item.
as a waypoint
2. Press In and release the
Thumb Stick to display the map item information
page.
3. Highlight the Save button and press the Thumb
Stick In to save the item as a waypoint.
To create a waypoint using the map panning
arrow:
2. A prompt asks you if you want to save the location
as a Waypoint. Press Yes and the Waypoint Page
displays, automatically assigning a number to the
waypoint. Highlight the Close button and press
the Thumb Stick In to exit the page.
To create a waypoint by entering coordinates:
1. Press In and hold the Thumb Stick to access the
Mark Waypoint page. You can also use the Find
Menu to display a previously saved waypoint.
2. Highlight the Location field and press in on the
Thumb Stick to open the on-screen keyboard.
Use the keyboard to change the location
coordinates and press the OK button to exit.
3. You may also change the waypoint name, symbol,
or add notes using the same process.
1. With the Pan Map feature active (refer to the Map
Page section of this manual), move the panning
arrow (map pointer) on the map to the location
or map item you want to mark, then press the
Thumb Stick In to display a prompt for a location
or information page for a map item
Rino® 520/530 Owner’s Manual
49
UNIT OPERATION > WAYPOINTS
Averaging a Waypoint
Averaging a waypoint location can increase the accuracy
of a waypoint at your current location by taking multiple
position readings and averaging the results.
3. Highlight either the bearing or distance field, then
press the Thumb Stick In to display the numerical
keyboard. Enter the new bearing or distance, then
highlight OK and press In to finish.
To average a waypoint:
Select Average Location from the options list or
the Avg button on the Mark Waypoint page when
marking a new waypoint only. Press the Thumb
Stick In to activate the Averaging Page. The
longer you allow averaging to run the greater the
location accuracy. Press Save when done.
Enter
Direction
Enter
Distance
Project Waypoint Page
Projecting a Waypoint
Editing a Waypoint
To project a waypoint:
To edit a waypoint:
Projecting a waypoint from any map item (another
waypoint, etc.) allows you to establish a new waypoint on
a bearing and distance projected from that map item.
1. Select a map item from the Find Menu.
2. Access the Option Menu using the on-screen
button at the top of the Information Page. Highlight
Project Waypoint and press In.
50
A waypoint or contact can be edited to add notes or
change the map symbol, name, coordinates, or elevation.
You can also delete a waypoint or contact.
Use the Find Menu to display the waypoint/contact
or highlight it on the Map Page and press the
Thumb Stick In.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > WAYPOINTS
To delete a waypoint or contact:
1. Use the Find feature to display the point.
2. Highlight the Delete button and then press the
Thumb Stick In. Confirm the deletion.
To move a waypoint by dragging it:
1. Use the Find Menu to display the Waypoint Page
for the waypoint you want to move.
2. Highlight and press the Map on-screen button to
display the waypoint on the map.
3. With the waypoint highlighted by the panning
arrow, press In and release the Thumb Stick. The
word “Move” displays beneath the panning arrow.
Deleting a Waypoint
Rino® 520/530 Owner’s Manual
4. Use the panning arrow to drag the waypoint to the
new location and then press the Thumb Stick In
to place it.
Press the Page/Quit button before pressing the
Thumb Stick to cancel moving the waypoint and
return to the Main Pages.
Moving a Waypoint
51
UNIT OPERATION > FIND
Find
To access the Find Menu:
The Find Menu allows you to Find stored locations
(waypoints and contacts) and map items (cities, exits,
etc.). They can be found by name or by those nearest to
your current location. If you are using Rino compatible
Garmin MapSource detailed mapping data, the list of
Find locations is expanded to include categories for
Points of Interest, Street Addresses, and Intersections.
Find Menu
1. Use the Thumb Stick to highlight the Main Pages
button and then press it In to display the list of
Main pages.
2. Highlight Main Menu and press In to display the
Main Menu.
3. From the Main Menu, highlight the Find icon and
press the Thumb Stick in to display the Find Menu.
Categories can be listed in several different ways:
By Name, Nearest Current Location, and Nearest a
Referenced Map location. The By Name list contains
every item in the map database for the selected category,
while the Nearest lists contains only those items that are
near to your Current Location or a referenced location.
The distance defined by “Nearest” varies because it
is determined by the density of items near you in the
selected category. There are more restaurants near you
than cites for example.
These pages are structured with a set of sub-menus and
location information pages that guide you through the
process of Finding locations.
52
Rino® 520/530 Owner’s Manual
UNIT OPERATION > FIND
Finding a Waypoint
Waypoints that you have created and stored in the Rino
520/530 can be found by selecting the Waypoint option
from the Find Menu. You can Find a waypoint from the
list of waypoints using the Nearest current location, By
Name (all waypoints in alphabetical order), or Nearest
referenced location options as explained on the previous
page. When selected from the list, the waypoint displays
on the Waypoint Information Page.
The Waypoint Information Page displays the waypoint
name or number, a map symbol, the location in lat/lon,
elevation, distance, bearing, and three on-screen buttons
for Go To, Map, and Delete functions.
To Find a waypoint by nearest:
1. Use the Thumb Stick to select Waypoint from the
Find Menu. Press the Thumb Stick In to display
the Waypoints List. The List is displayed as “All
Symbols Near Current Location.”
Rino® 520/530 Owner’s Manual
2. Use the Thumb Stick to select the desired
waypoint from the list and then press the Thumb
Stick In to display the Information Page for that
waypoint.
3. Select Go To to create a direct line of travel to
the waypoint. Select Map to view the waypoint
location on the map or select Delete to delete the
waypoint.
4. Press the Option Menu button to access
additional features. You can select: Send Location
(to other Rino users), Project Waypoint, Set
Proximity (alarm), Add to Route, View Sun & Moon
(reports for that waypoint), View Hunt & Fish
(reports for that waypoint), or Reposition Here.
To Find a waypoint by selecting a symbol:
1. With the Waypoints List displayed, use the
Options Menu to view waypoints using the same
type symbol by highlighting “Select Symbol” and
pressing In on the Thumb Stick.
2. A “Used Symbol” window appears with a list of all
the symbol types assigned to waypoints.
53
UNIT OPERATION > FIND
To Find a waypoint by name:
1. Use the Thumb Stick to select Waypoint from the
Find Menu. Press the Thumb Stick In to display
the Waypoints List.
Waypoints List
2. Use the Thumb Stick to enter the name of the
waypoint that you would like to Find.
3. Select OK when you are finished entering the
name. The waypoint list opens with the name
closest to the name you entered on the top.
4. Select the desired waypoint from the list and
then press the Thumb Stick In to display the
Information Page for that waypoint.
5. With the Waypoint Information Page displayed,
select Go To to create a direct line of travel to the
waypoint. Select Map to view the waypoint location
on the map or select Delete to delete the waypoint.
6. Press the Option Menu button to access
additional features.
Finding a Geocache
Waypoint Information Page
54
Information Page Options Menu
The Find Geocache feature allows you to view and
navigate to geocache locations you created using your
Rino or downloaded from your computer. For more
information about geocaching, visit the Garmin web site
www.garmin.com/outdoor/geocaching/.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > FIND
To Find a geocache:
1. From the Find Menu, select
the Geocache icon and press
the Thumb Stick In.
2. If you have not established
a geocache list, you are
presented with the Geocache
Geocache List
setup page. Here you are
asked to select symbols for geocache locations.
Standard symbols for geocaching are presented
along with a calendar entry option.
3. Change the symbols if desired and select “Yes” or
“No” for calendar entry, then use the Close button.
Finding a Contact
Contacts that you have received in the Rino 520/530 can be
found by selecting the Contacts icon from the Find Menu.
To Find a contact:
1. From the Find Menu, highlight Contacts and
press the Thumb Stick In.
Rino® 520/530 Owner’s Manual
Contact List
2. From the Contacts List, select the desired contact
and press the Thumb Stick In.
3. With the Contact Information Page displayed,
select Go To to create a direct line of travel to the
contact. Select Map to view the contact’s location
on the map or select Delete to delete the contact.
If the contact did not have a GPS location on the
last transmission, a question (?) mark appears in
the location field.
4. Press the Option Menu button to access
additional features.
55
UNIT OPERATION > FIND
Finding a City
Cities can be found by selecting the Cities option of the
Find Menu, selecting the city from the list of Nearest or
By Name, and then displaying the City Information Page.
The City Information for the selected city displays,
including the city name, the size by population, and
distance from your location. You can view it on the
map, or create a Go To direct route to the city from your
current location or from a location defined by the Panning
Arrow (Map Pointer). You can also save the city as a
waypoint or add it to an existing route.
To Find a city:
1. From the Find Menu use
the Thumb Stick to select
the Cities option, then
press it In to display the
Find Nearest or Find By
Name prompt. Selecting
Find Nearest Cities List
By Name displays the
keyboard as an alternative
to scrolling through the list of nearest cities.
56
2. If using Find By Name, begin spelling the name
of the city by using the keyboard. When you have
entered enough characters to begin to define the
name, a match list displays.
If you are using Find By Nearest, scroll through
the list to Find the city you want. Use the Thumb
Stick to select the desired city from the list and
then press it In to display the Information Page for
that city.
If you use Select Map (which is displayed only
when you have more than one type of detailed
data map downloaded from MapSource to your
Rino), you have the option to choose which map
you want data from.
If using Change Reference, follow instructions
when the map displays and select a location to
base the city search from.
3. With the Information Page displayed, you can
select Go To, Map, or Save options.
4. Press the Option Menu button to access
additional features.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > FIND
Finding an Exit
You can use the Find Exit option
to locate a nearby exit on an
interstate highway. Exits are
listed only by Nearest to your
current location or a referenced
location you can specify.
Find Nearest Exits List
Exit information pages provide a
variety of information about services near each exit, such
as rest stops, lodging, restaurants, and service stations.
Some services can be selected and a separate information
page displays with specific information concerning what
types of fuel, mechanical, and food services are available.
To Find an exit:
1. Use the Thumb Stick to highlight the Exits icon
and then press it In to display the Exits List.
2. A list of exits nearest to you displays. The header
text indicates the interstate highway that is served
by the exits. A field at the bottom of the page
indicates distance and bearing to the exit. Scroll
through the list to highlight the desired exit.
Rino® 520/530 Owner’s Manual
3. Press the Thumb Stick In to display the
Information Page for that exit. This page contains
the exit description with a list of available services
near that exit along with the distance and bearing.
4. Use the Thumb Stick to move to the list of
services and highlight a selection from the list.
5. Press the Thumb Stick In to display the
Information Page for the selected service.
The Exit Services Information Page displays a
list of services. Highlight the desired service and
press the Thumb Stick for details.
At the bottom of these Information Pages are onscreen buttons for Go To, Map, and Save.
6. Press the Option Menu button to access
additional features.
57
UNIT OPERATION > FIND
Finding a Point of Interest
You can use the Find Points of Interest option to
locate a nearby restaurant, lodging, landmark, public
building, park, etc. However, you must have transferred
a MapSource CitySelect or MetroGuide map to the unit
map database. Otherwise, this option, plus Address and
Intersection options, are not displayed on the Find Menu.
Here is a list of Point of Interest categories:
•
•
•
•
•
•
•
•
58
Food & Drink
Lodging
Attractions
Entertainment
Shopping
Marine Points
Recreation
Geographic Points
•
•
•
•
•
•
•
•
Fuel Services
Transportation
Hospitals
Geographic Points
Auto Services
Community
Marine Points
Other
In many instances, these categories are subdivided into
types, such as in the instance of Food & Drink. When you
select Food & Drink from the list of categories, you have
the option of choosing from a list of types that includes
All Types and cuisine options such as American, Asian,
Barbecue, Chinese, etc.
Food & Drink types
Once you have selected an item, you can display the
Information Page for that item. You can then use the onscreen buttons to Go To or view the location on the Map;
or use the Option Menu for more choices.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > FIND
To Find a point of interest:
1. Use the Thumb Stick to select the desired
category and then press it In to display the list for
that category.
2. Use the Option Menu button at the top of page to
select from either By Name or Nearest options.
Selecting By Name displays a keyboard allowing
you to enter the characters of the name you want.
A list of matches displays when enough characters
are entered.
3. Use the Thumb Stick to highlight your selection
from the list and then press it In to display the
Information Page for that item.
4. Use the on-screen buttons to Go To or view on
the Map, or use the page Option Menu.
5. Press the Option Menu button to access
additional features. You can select: Send Location
(to other Rino users), Project Waypoint, Find Near
Here, Change Reference, Set Proximity (alarm),
Add to Route, View Sun & Moon (tables for that
waypoint), View Hunt & Fish (tables for that
waypoint) or Map Information.
Rino® 520/530 Owner’s Manual
All POI’s By Name
POI’s By Category
59
UNIT OPERATION > FIND
Finding an Address or Intersection
You can enter a street number, choose a street name
from a list and Find an address within the area of map
data coverage or enter two street names and locate the
intersection. To use these options, however, you must be
using a MapSource product that provides this type of map
data.
To locate an address:
1. From the Find Menu, use the Thumb Stick to
highlight the Address icon and press it In to
display the Find Address page.
2. Highlight the Number field and use the keyboard
for entering numbers.
3. Move to the Street field using the Thumb Stick.
4. Press the Thumb Stick In to display the Select
Street Name list. Find the street by using the
keyboard to enter characters until a list appears.
5. With the desired street highlighted, press the
Thumb Stick In to place the street name on the
Find Address page. A window at the bottom of the
page displays a list of matches and the quality of
each match. You may also use the Option Menu to
Clear Region, Enable City Filter or Clear All.
6. Use the on-screen buttons at the bottom of the
page to Go To, view the item on the Map, Save
to save as a waypoint, or use the Option Menu
for other choices. Highlight the Main Page Menu
button and press In to close.
Entering a Street Number
60
Address Matches
Rino® 520/530 Owner’s Manual
UNIT OPERATION > FIND
To locate an intersection:
1. Display the Find Menu and use the Thumb Stick
to highlight the Intersection category and press it
In to display the Find Intersection page.
2. Highlight the first Street field and then press the
Thumb Stick In to display the Street list.
3. Enter the name of the street in the name field at
the top of the list using the keyboard data entry
method discussed in the Quick Start Guide. Once
you have spelled enough of the street name, a
list of matches displays, often with several streets
on the list. Press the Thumb Stick In to move
the highlight to the street list and then scroll up
or down until you Find the street name you want.
Press it In to place the name in the field.
4. Repeat the process for the second street name.
When the second street has been entered, a
search for matches begins.
Rino® 520/530 Owner’s Manual
5. Highlight the best match and then press the
Thumb Stick In to display the Information Page
for the intersection. Use the on-screen buttons at
the bottom of the page to Go To, view the item on
the Map, Save to close, or use the Option Menu
for other choices.
Enter Two Street
Names
Finding an Intersection
61
UNIT OPERATION > FIND
Recent Finds
You can use the Recent Finds option to locate Points of
Interest, Cities, Waypoints, Contacts, Intersections and
other locations you have recently retrieved. The process
for Finding recent points from the Find Menu is the same
as Finding a regular waypoint.
To Find a Last Found Place:
1. Use the Thumb Stick to select the Recent Finds
option from the Find Menu and then press it In.
2. Press Left then Up or Down on the Thumb Stick
to highlight an item on the list and press the
Thumb Stick In to display the Information Page
for that item.
3. With the Information Page displayed, you can
select Go To to create a direct line of travel to the
item. Select Map to view the waypoint location.
For Waypoints and Contacts, you may also
choose to Delete to permanently remove that
item. Access the Options Menu for other choices.
62
Recent
Finds List
Recent Finds Page
To clear the list, access the Options Menu to
display the “Remove All” option.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > USING GO TO NAVIGATION
Using Go To Navigation
The Go To is the basic function that allows you to create
a route to a destination, (waypoint, city, or point of
interest). Once you have accessed the Information Page
for an item, use the Go To button at the bottom of the
page to initiate travel, using the Map and Compass Pages
for guidance.
To activate a Go To:
1. Use the Find Menu to access the Information
Page for any desired destination and use the
Thumb Stick to highlight the Go To button.
2. Press the Thumb Stick In to start navigation. A
“Follow Road/Off Road” prompt displays before
the route is calculated if activated in the Routes
Setup or you have loaded detailed routable maps .
3. If you select “Follow Road” a “Calculating Route”
message displays with percentage timer to
completion. “Off Road” immediately projects a line
to your destination.
Rino® 520/530 Owner’s Manual
4. The Map page is displayed where you can
observe your movements and a navigation line
indicating the path from your current location to
your destination.
5. Use the Page/Quit button or Main Menu button
to access one of the other navigation pages;
Compass Page, Highway Page or Active Route
Page with Turn-By-Turn instructions.
When you are close to your destination, an “Arriving at
Destination” message appears.
To stop navigation, select the on-screen Option Menu
button at the top of a Navigation Page. Select Stop
Navigation, then press the Thumb Stick In.
Viewing a Go To on
the Map Page
63
UNIT OPERATION > TRACKS PAGE
Tracks Page
The Rino 520/530 draws an electronic bread crumb trail
on the Map Page as you travel along. This bread crumb
trail is the Track Log. The Track Log contains information
about points along its path, including time, and position.
The Rino 520/530 uses this information to allow you to
navigate using the saved track. You may also save tracks
from other Rino users as they communicate with you.
To open the Tracks page:
1. Access the Menu Page by using the on-screen
menu button or the Page button.
2. Select the Tracks icon and press the Thumb
Stick In. The Tracks page opens.
To save and use a Track:
1. Access the Tracks page from the Main Menu.
Press the on-screen Off button In to pause track
logging. When track logging is active the On
button is filled by a dot.
64
2. Highlight the Save on-screen button and then
press the Thumb Stick In to display the track log
“Do you want to save the entire track?” prompt.
3. If you choose Yes the entire track is saved.
4. If you choose No, the track is displayed on the
map along with a panning arrow. You are asked
to select a beginning point for the part of the track
you want to save. Move the panning arrow to the
desired point and then press the Thumb Stick In.
4. The prompt then asks you to select the ending
point for the saved track. Move the panning arrow
to the desired point. Press the Thumb Stick In to
save the track log and display the Track Page. The
Track Page shows the track name (which can be
renamed using the keyboard for data entry), the
total distance of the track, track area (if available),
a Show on Map option, and on-screen buttons for
Delete, Map, OK, and TracBack.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > TRACKS PAGE
Using the TracBack Feature
The TracBack feature allows you to return along a
traveled path (or another Rino user’s path) without
marking any waypoints. When you are ready to return to
where you started, the Rino 520/530 takes you back by
following the Track Log that you left behind. You can
save a total of 20 tracks in the unit memory. The Track
Log starts recording as soon as the unit gets a satellite
location fix and the Track Log feature is turned on. When
you no longer need a Track Log you can press the onscreen Clear button to remove it.
If you want to keep a record of a certain track log or use
the TracBack feature, it is recommended that you clear
the Track Log before you start traveling. The percentage
of memory used by the current track log is displayed in
a window at the top of the page. After the Track Log is
Cleared, it displays zero percent.
Saved Track
Tracks Page
Rino® 520/530 Owner’s Manual
65
UNIT OPERATION > TRACKS PAGE
When the track log memory field reaches 100%, the most
recent track points start to overwrite the least recent if the
default setting Wrap When Full remains selected on the
track log setup. To avoid losing track points you want,
save the Track Log when it approaches the 99% mark.
The active track log stores up to 10,000 points.
The Saved Track Page displays the track and it can also
be displayed on the Main Map Page as you navigate. You
may save up to 20 tracks with 500 points per track in the
unit. Saved Contact tracks count towards this total. Tracks
are marked BEGIN and END.
To use the TracBack feature:
1. Highlight the TracBack button on the Tracks
Page and press the Thumb Stick In. The track
is displayed on the map and you are prompted to
“Select the point you want to TracBack to.”
2. Use the panning arrow to select the desired point
and press the Thumb Stick In to enable.
3. Use the Map Page or the Compass Page to
navigate the Track.
TracBack
Track on Map
66
Rino® 520/530 Owner’s Manual
UNIT OPERATION > TRACKS PAGE
Setting up the Track Log
You can set the track recording
interval to Distance, Time, or
Automatic. You can set the Track
display resolution to High, Medium,
Low, and Lowest. You can also use
the Option Menu to delete all saved
tracks.
Using Track Profiles
Track Log Setup
To use Track Log Setup options:
1. Highlight the Tracks Page Setup button on the
page and press the Thumb Stick In to display the
Setup Page.
2. You can check the Wrap When Full option by
highlighting it and then pressing the Thumb Stick
In. You can highlight the Record Method and
Interval fields and press the Thumb Stick In to
display their options. Interval options change to
accommodate the Record Method choices.
Rino® 520/530 Owner’s Manual
Once you have saved a track, you
not only have a record of the path
you traveled but an altitude profile
as well. (Rino 530 Only)
To view a Track Profile:
1. With the Saved Track Page for
Track Profile
the desired track displayed,
press the Option Menu button to display the
Profile option.
2. Press the Thumb Stick In to display the Track
Profile.
The beginning of the track is marked by a flag and
you can scroll across the profile using the Thumb
Stick.
As you scroll, the elevation for each point is
displayed at the top of the page and the distances
of that point from the Start and End points are
displayed at the bottom of the page.
3. At any point on the profile, you can press the
Thumb Stick In to display that point on the map.
67
UNIT OPERATION > ROUTES PAGE
Routes Page
Route navigation allows you to
create a sequence of intermediate
waypoints that leads you to your
final destination. The Rino 520/530
stores 20 routes, each with up to 50
Routes List Page
waypoints. A route can be created
and modified from the Routes Page,
and waypoints can be added to a route from the Find
Menu.
4. Select a route waypoint from one of the Find Menu
categories and display the Information Page for
the selected waypoint, city, exit, point of interest,
etc. Highlight the on-screen Use button and press
the Thumb Stick In to place it on the Routes List.
5. To add more waypoints to the route, repeat the
process in Steps 3 and 4. The route is named for
the first and last waypoints on the route.
You can add waypoints to the end of an existing route at
any time by using the Find Menu.
Creating and Using a Route
To create a route:
1. Access the Routes page from the Main Menu. The
page has a New button, a list of routes, and an
Active route button.
2. Use the Thumb Stick to highlight the New button
and press it In to display the Route Setup Page.
3. With an empty row (dashed) in the route list
highlighted, press the Thumb Stick In to display
the Find Menu.
68
New Route Page
Rino® 520/530 Owner’s Manual
UNIT OPERATION > ROUTES PAGE
To add a Find Menu item to a route:
1. Select an item from the Find Menu and display
its Information Page. If a contact is used in a
route, the route changes as the contact’s position
is updated, or it may be saved as a Waypoint to
serve as a stationary point.
2. Select the page Option Menu and select Add To
Route to display the Routes List.
3. Highlight and select the route desired and then
press the Thumb Stick In. A “Waypoint Added
Successfully” message displays.
Editing a Route
To remove all waypoints:
1. From the Route Page, select the on-screen
Option Menu button and press the Thumb Stick
In to access the Option Menu.
2. Highlight the Remove All option and then press
the Thumb Stick In to remove all waypoints from
the list. When you see the prompt “Do you really
want to remove all waypoints from the route?”,
select Yes.
Rino® 520/530 Owner’s Manual
Route Options
To reverse the route:
1. From the Route Page, select the on-screen page
Option Menu button and press the Thumb Stick
In to access the Option Menu.
2. Highlight the Reverse Route option and then
press the Thumb Stick In to reverse the order of
waypoints in the list. You can now navigate back
to your original location. To change the route back
to the original order, repeat this process.
69
UNIT OPERATION > ROUTES PAGE
To copy the route:
1. From the Routes Page, select the on-screen page
Option Menu button and press the Thumb Stick
In to access the Option Menu.
2. Highlight the Copy Route option and then press
the Thumb Stick In to copy. The copied route
displays on the Routes Page and is named the
same but followed by the numeral 1 (one). You
may then rename and/or modify the copied route.
To delete the route:
1. From the Route Page, select the on-screen page
Option Menu button and press the Thumb Stick
In to access the Option Menu.
2. Select Delete and then press the Thumb Stick In.
When you see the prompt “Do you really want to
delete route?”, select Yes.
To restore default settings for the route:
1. From the Route Page, select the on-screen page
Option Menu button and press the Thumb Stick
In to access the Option Menu.
70
2. Select Restore Defaults and then press the
Thumb Stick In to restore factory settings.
To review a route point:
1. Select the point from the Route Points List and
press the Thumb Stick In to access the Option
Menu for the waypoint.
2. Highlight Review and then press the Thumb
Stick In to display the Information Page.
3. Highlight the Close button and then press the
Thumb Stick In or use the Page/Quit button to
return to the Route List.
To insert a new point on the route list:
1. Select the row where you want the new point
inserted before. Press the Thumb Stick In.
2. Highlight Insert and press the Thumb Stick In to
display the Find Menu and select a new waypoint,
city, exit, point of interest, etc.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > ROUTES PAGE
3. With the new point highlighted, press the Thumb
Stick In to display the Information Page for the
new point and then select the on-screen Use
button to add it the route.
To change a route point:
1. Select the waypoint that you want to change from
the Route Waypoints List and press the Thumb
Stick In.
2. Highlight Change and press the Thumb Stick In
to display the Find Menu or create a new waypoint
and add it to the points list.
3. Select a new waypoint, access its Information
Page and press the on-screen Use button to
replace the old route waypoint.
To move a route point:
Route point review options
To remove a point from the route list:
1. Select the point that you want to remove from the
Route Waypoints List and press the Thumb Stick
In.
2. Highlight Remove and press the Thumb Stick In
to remove the waypoint from the list.
Rino® 520/530 Owner’s Manual
1. Select the point from the Route Points List and
press the Thumb Stick In.
2. Highlight the Move option and press the Thumb
Stick In to select the waypoint.
3. Use the Thumb Stick to move the point up or
down in the list. Press the Thumb Stick In to
leave the waypoint in the new list order.
71
UNIT OPERATION > ROUTES PAGE
Adding or Editing from the Route Map
Page
You can use the panning arrow with the Route Map Page
displayed to add or edit route waypoints.
To add a point at either end of a route:
1. Select the Route from the Routes List. Press the
Thumb Stick In to display the Route Page.
2. Highlight the on-screen Map button at the bottom
of the page and press the Thumb Stick In to
display the Route Map Page.
3. Use the Thumb Stick to move the panning arrow
to either end of the displayed route until the end
point is highlighted. Then press the Thumb Stick
In and select Add Turns. This option appears only
when highlighting the end point of a route.
4. Move the panning arrow to highlight a map item
where you would like to extend the route and
press the Thumb Stick In to add the new point.
If on a point where there is not a highlighted map
item, a prompt to save as a waypoint appears.
72
5. Select “Yes” save as a waypoint to view the
waypoint information page. Close the page to
save and view it on the map.
6. Press the Thumb Stick In to place the new route
point. Use the Page/Quit button to exit.
To add a route point within a route:
1. Follow steps 1 and 2 in the previous instructions.
2. Use the Thumb Stick to move the panning arrow
to a route line. When the arrow touches the line,
the line highlights in a different style. Press the
Thumb Stick In to display the word ADD next to
the line.
3. Drag the line to a highlight a map item then press
the Thumb Stick In to place the new route point.
If on a point where there is not a highlighted map
item, a prompt to save as a waypoint appears.
4. Select “Yes” save as a waypoint to view the
waypoint information page. Close the page to
save and view it on the map.
5. Press the Thumb Stick In to place the new route
point. Use the Page/Quit button to exit.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > ROUTES PAGE
To review or remove a route point:
1. Select the Route from the Routes List. Press the
Thumb Stick In to display the Route Page.
2. Highlight the Map button and press the Thumb
Stick In to display the route.
3. Use the Thumb Stick to move the map panning
arrow to the point you want to review and press In.
Select Review or Remove and press In again to
either display the Information Page or remove it
from the route.
Select Next and press In to view the next waypoint.
Setting Up Routing Methods
3. Select Routing and press the Thumb Stick In to
open the Routing Setup Page.
4. Select the Guidance Method and choose
“Prompted” if you want to choose from “Follow
Road” or “Off Road” each time a route is being
calculated.
5. In the Follow Road Method field make a selection
from the options provided.
6. If you want a Next Turn Preview to display, select “On”.
7. When using the “Follow Road” guidance method,
select the Follow Road Options button and press the
Thumb Stick In to choose from a page of options.
The Routing Setup Page allows you to customize how
routing functions behave. There are setup options for
route creation and methods of navigation.
To use the Routing Setup:
1. Use the Page/Quit button or Main Page button to
access the Main Menu.
2. Use the Thumb Stick to highlight the Setup Icon
and then press it In to open the Setup Menu.
Rino® 520/530 Owner’s Manual
Routing Setup Page
Follow Road Options
73
UNIT OPERATION > ROUTES PAGE
Navigating a Route
A Route can be navigated using the Map Page, the Compass
Page, or the Highway Page. To stop navigation, highlight
the Stop Navigation option on any of the three page’s
Option Menus or select Stop on the Route Page.
To navigate a route:
1. Select a route from the Routes List and then press
the Thumb Stick In.
2. Highlight the on-screen Navigate button at the
bottom of the page and then press the Thumb
Stick In to begin navigating the route on the map.
3. To review the Active Route highlight the Active
button on the Routes Page. Two versions of the
Active Route can be displayed, one for “Follow
Road” and one for “Off Road.“
Follow
Road
(Turn-By-Turn)
74
Off
Road
(Point-toPoint)
Using the Turn-By-Turn Active Route Page
When navigating a Route that follows roads, the Active
Route Page is displayed as a Turn-By-Turn Page with
each turn on the route listed in order and defined by a
graphic arrow, a description of the turn and direction
to go, the distance to that turn, and the time remaining
before you reach the turn. Each turn on the route displays
a turn preview page just before you reach the turn
location. The preview page shows you a detailed map of
the turn and the direction to go.
To view the Turn-By-Turn Active Route Page:
When on a Route that follows roads, press the
Page/Quit button to cycle to the page or press the
Main Page button to select it from the Main Page
Menu.
To view the preview page for
any turn on a route:
Use the Thumb Stick to highlight
a turn on the Page and then
press In to display the preview
page for that turn.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > HIGHWAY PAGE
Highway Page
When you are navigating a Go To or Route, the Highway
Page can guide you to your destination using navigation
data fields and a graphic highway. Up to four userselectable data fields display information such as speed,
distance, time to next point on the route, etc. The Show
Data Fields options are similar to the Map and Compass
pages.
The highway graphic provides a visual path to your
destination. Your course is represented by a center line in
the middle of the graphic. As you move toward each point
on the route, the graphic shows the direction you should
move to stay on course to the point. You can add this page
to the page sequence by using the Page Sequence Setup
option.
2. Highlight the Highway Page icon from the Main
Menu and press the Thumb Stick In to observe
your path of travel displayed on the highway
graphic.
3. Press the Options Menu button to display the
Options Menu and select Data Fields to customize
the page to your requirements.
4. Select “Show: 3 Data Fields or 4 Data Fields”
5. Highlight the first field and press the Thumb Stick
In to display the list of data options. Repeat for
each field.
To navigate using the Highway Page:
1. While on an active route, press the Page/Quit
button or the Main Page button to access the
Main Menu.
Rino® 520/530 Owner’s Manual
Highway Page
75
UNIT OPERATION > SETUP PAGES
Setup Pages
The Setup Pages allow you to customize the Rino
520/530 to your personal preferences. You can choose
time settings, units of measure, display backlighting and
timeout settings, heading measurement, interface options
and system operating mode.
By highlighting the icons on the Setup Menu and then
pressing the Thumb Stick In, you can display the Setup
Page for each of the menu items.
power connection settings. See the “Appendix” for
WAAS capability information.
To access the System Setup page:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the System icon to open the System Setup
page.
To access the Setup Menu
1. Press the Page button or the Main Page button to
open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
There are then several more icons to choose from
in the Setup Menu.
System Setup Page
The System Setup Page allows you to change GPS
operation modes, use the WAAS capabilities, set AA
battery type, external power loss settings, and external
76
The options menu allows
you to restore Default
settings and view the
version of unit operating
software.
System Setup Page
The Option Menu allows you to restore defaults or
display the current version of unit operating software and
the Unit I.D. Number. Software updates and instructions
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SETUP PAGES
for downloading are available from the Garmin Web site
(www.garmin.com).
Choose one of the GPS options other than Normal to
significantly save battery power. The Battery Saver mode
reduces the rate of satellite signal position updating
and the GPS Off option stops satellite signal reception
altogether. The Demo Mode simulates navigation.
Enable or disable WAAS.
Set the Battery Type for more accurate battery capacity
status when using the optional battery pack for alkaline or
NiMH “AA” batteries.
Set the unit to turn Off if external power is lost.
Set the unit to power On when the charger is connected or
to charge the unit only.
Radio Setup Page
This setup page allows you to adjust the radio operation
to meet your requirements. (See page 14 for detailed
instructions.)
Rino® 520/530 Owner’s Manual
Display Setup Page
You can choose a display mode, a
color scheme for day and for night
viewing, adjust the amount of time
that the backlighting feature stays
on, and set the level of brightness.
To access the Display
Setup page:
Display Setup Page
1. Press the Main Page button to access the Main Menu.
2. In the Main Menu, scroll down and select Setup
and then Display.
Display Mode—Can be set for Auto (changes from day
to night mode and back again at dusk and dawn), Day
only, or Night only.
Color Scheme Selection—Can be set in Day and Night
modes to one of 10 color schemes. As you scroll up and
down the list of schemes, each color scheme previews.
Backlighting Timeout—Choose from Stays On or
delays of 15 seconds, 30 seconds, one minute, or two
minutes before timing out.
77
UNIT OPERATION > SETUP PAGES
Backlight Intensity Level—Use a pop-up slider to
adjust the brightness to your preferences. The percent set
displays when you close the slider.
Tones Setup Page
This setup page allows you to select a unique tone for
each of the different tone applications. (See page 16 for
detailed instructions.)
Page Sequence Setup
You can add, remove, or reorder any of the Main Pages,
plus additional pages. The default Main pages are Radio,
Map, Navigation, Altimeter, Trip Computer, and Main
Menu. The Main Menu cannot
be removed from the page
sequence. If a page is added to
the Main Page Sequence, it does
not appear in the Main Menu.
Inserting a new page in
the Page Sequence
78
To move, insert or remove a Main Page:
1. From the Main Menu, highlight the Option Menu
button and press the Thumb Stick In. Highlight
Page Sequence Setup and press In.
2. To rearrange a page in the page sequence,
highlight the page and press In. Select Move
then move the Menu item Up or Down using
the Thumb Stick. When the desired position is
displayed, press the Thumb Stick In.
3. To insert a new page, highlight the page you want
to insert it before and press the Thumb Stick In.
Select Insert, then choose a page from the list
and press the Thumb Stick In.
4. To remove a page in the order, highlight the page
and press In. Select Remove and press the
Thumb Stick In.
Map Setup Page
This setup page has six sections and allows you to
customize the way the map page displays. (See page 29
for detailed instructions.)
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SETUP PAGES
Routing Setup Page
This setup page allows you to set methods for guidance,
navigation methods, and next turn prompts, and route
type selection. (See page 73 for detailed instructions.)
Geocache Setup
The Geocache Page setup allows
you to find and record items hidden
at geographic locations. Refer to
the Garmin web site for information
on how to download geocache
Geocache Setup
locations from the internet, www.
garmin.com/outdoors/geocache/.
To setup the Geocache feature:
1. Press the Page/Quit button or the Main Page
button to access the Main Menu.
2. Highlight the Setup icon from the Main Menu and
press the Thumb Stick In to display the Setup
Menu.
3. Select Geocache and press the Thumb Stick In
to display the setup page.
Rino® 520/530 Owner’s Manual
4. Use the Thumb Stick to highlight the symbol
fields if you want to assign other symbols than the
standard geocache symbols already in place.
5. Select “Yes” or “No” for a calendar entry when a
geocache is found.
Marine Setup
The Marine Page setup allows you to set values for the
limits, which activate alarm features
specific to maritime navigation.
To setup the Marine alarms:
1. Press the Page/Quit button or
the Main Page button to access
the Main Menu.
Marine Setup
2. Highlight the Setup icon from
the Main Menu and press the
Thumb Stick In to display the Setup Menu.
3. Select Marine and press the Thumb Stick In to
display the setup page.
4. Highlight the box adjacent to each alarm field and
activate by pressing the Thumb Stick In.
79
UNIT OPERATION > SETUP PAGES
5. Then highlight each field to enter or select options
or enter values.
Time Setup Page
You can set the time to match your geographical location.
To access the Time Setup page:
1. Press the Page/Quit button
or the Main Page button to
open the Main Menu.
2. In the Main Menu, scroll
down and select Setup.
3. Select the Time icon to
open the Time Setup page.
Time Setup Page
Time Format—Allows you to
choose from 12-hour (like a standard clock with 12-hour
AM and PM cycles) or 24-hour time format ( a 24- hour
cycle, also called Military Time).
Time Zone—Can be set to one of the eight US Time
Zones, or 24 International Time Zones (nearest city or
geographical region). Select Other so you can enter the
UTC Time Offset.
80
Daylight Saving Time—Can be turned On or Off or
set to Automatic and will change according to your time
zone.
To set the time:
1. Use the Page button to access the Main Menu.
2. Use the Thumb Stick to highlight the Setup Icon.
Press the Thumb Stick In to display the Setup
Menu.
3. Use the Thumb Stick to highlight the Time Icon.
Press the Thumb Stick In to display the Time
Page.
4. Use the Thumb Stick to highlight the Time Zone
field. Press the Thumb Stick In to display the time
zone list.
5. Highlight a time zone from the list and then press
the Thumb Stick In.
6. If you choose Other, you must enter a UTC offset
value.
7. The correct time displays at the bottom of the
page.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SETUP PAGES
Units Setup Page
The Units features are best used by individuals with a
working knowledge of map grids and datums. To learn
more about these subjects, visit the National Imagery and
Mapping Agency at http://www.nima.
mil or inquire at your local library.
To access the Units Setup
page:
1. Press the Page/Quit button or
the Main Page button to open
the Main Menu.
Units Setup Page
2. In the Main Menu, scroll down
and select Setup.
3. Select the Units icon to open the Units Setup
page.
Position Format—Allows you to choose from different
grid formats. The default position format, ‘hddd°mm.
mmm’ displays the latitude and longitude in degrees and
minutes and is most commonly used.
Rino® 520/530 Owner’s Manual
LORAN TD Format
When creating new waypoints using LORAN TD
coordinates, you must set the correct LORAN chain
number and secondary stations in the Setup TD field
before storing the waypoint. After the waypoint is
stored in unit memory, it always
references the LORAN chain
number and secondary stations
currently selected in the Setup
TD field. If you enter a different
LORAN chain number, change the
secondary stations, or offsets in the Loran TD Setup
Setup TD field, the active waypoint
information reflects those changes. Because the unit
does not rely on the LORAN signal for navigation, it can
reference a different GRI chain and/or secondary stations
and still navigate to the location stored in memory.
To adjust the settings, select Loran TD as the Position
Format to open the Loran TD setup window. To change
the settings of any fields, highlight the field, press the
Thumb Stick In. When done, highlight Save and press In.
81
UNIT OPERATION > SETUP PAGES
For more information on Loran TDs, you may download
Garmin’s Loran TD Position Format Handbook from
the Garmin web site at http://www.garmin.com/support/
userManual.jsp.
Map Datum—Offers a selection of nearly all map
datums in common use. Every map is based on a map
datum (a reference model of the earth’s shape) and is
usually listed in the title block of the map. If you are
comparing GPS coordinates to a paper map, chart, or
other reference, the map datum in this field must match
the horizontal map datum used to generate the map or
other reference. The default datum is WGS-84 (World
Geodetic Survey 1984) and should only be changed when
using maps or charts specifying a different datum. If a
map does specify a datum, use the options list to Find
datums applicable to the region of the map, selecting the
one that provides the best positioning at a known point.
If necessary, you also may choose the User datum for
custom designed grids.
82
NOTE: The User datum is based on a WGS-84-Local datum and is an advanced feature for unlisted
or custom datums. To learn more, check your local
library or the Internet for educational materials on
datums and coordinate systems.
Distance/Speed—Choose from five units of measure to
display your rate of travel.
Elevation/Vertical Speed—Choose from three units of
measure to record your elevation and vertical speed.
Pressure—Choose from inches, millibars, or
hectopascals to measure the pressure.
Temperature—Choose from Celsius or Fahrenheit.
Depth—Choose from Feet, Fathoms, or Meters.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SETUP PAGES
Switch to compass heading when below–Enter the
desired speed for the Rino 530 to switch from using GPS
to using the compass for guidance.
Heading Setup Page
You can select the type of heading
displays, North References, or
magnetic variation (when set to
“User”).
To access the Heading
Setup page:
Heading Setup Page
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select Setup
then select the Heading Setup page.
Display—Allows you to choose from Cardinal Letters,
Degrees or Mils.
North Reference—You can choose from True, Magnetic,
Grid or User options. If User is chosen, you must correct
for the Magnetic Variation. The Electronic or GPS
compass uses the North Reference setting to create a
bearing.
The following features apply to the Rino 530 only:
Rino® 520/530 Owner’s Manual
for more than…—Enter a time limit to switch to the
compass. When you travel at the speed entered above for
the time entered here, the Rino 530 switches from GPS to
the compass.
To select either option:
Highlight the field and then press the Thumb
Stick In to display the options.
Calibration Setup Page
Available for the Rino 530 only, the Calibration Setup
Page allows you to calibrate both the Compass and
Altimeter for increased accuracy in navigation.
To calibrate the Compass:
Refer detailed instructions on page 35.
To calibrate the Altimeter:
Refer detailed instructions on page 41.
83
UNIT OPERATION > SETUP PAGES
Altimeter Setup
The Altimeter Setup Page allows
you to set the Altimeter to selfcalibrate each time you turn on the
Rino unit in order to function as a
barometer or to manually calibrate
when you have accurate elevation Altimeter Setup Page
or pressure data.
To setup the Altimeter:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Altimeter icon to open the Altimeter
Setup page.
4. Highlight the Auto Calibration field and press the
Thumb Stick In to select from On or Off. When
On, elevation is corrected by GPS.
5. Highlight the Barometer Mode field and press
the Thumb Stick In to select “Variable Elevation”
(used when you are moving) or “Fixed Elevation”
(Used when stationary.)
84
6. To manually calibrate the Altimeter, refer to
detailed instructions on page 41.
Welcome Page Setup
The Welcome Page setup allows you
to insert a message such as ownership
information on the Welcome Page (the
first page to display when you turn the
unit on.)
To setup the Welcome Page:
Welcome Page
1. Press the Page/Quit button or the Main Page
button to access the Main Menu.
2. Highlight the Setup icon from the Main Menu and
press the Thumb Stick In to display the Setup
Menu.
3. Select Welcome Message and press the Thumb
Stick In to display the setup page.
4. Use the on-screen keyboard to begin entering
your message in the Welcome Message field.
5. Highlight OK and the press the Thumb Stick In to
finish.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SETUP PAGES
Interface Setup Page
The Interface Settings Page
allows you to choose from
different input/output serial data
formats. This feature is used
when connecting to external
NMEA devices, a DGPS beacon Interface Setup Page
receiver, a personal computer,
etc. To use non-Garmin data formats, you must use the
RS232 to Mini USB interface cable described in the
Accessories section of this manual. Refer to your Garmin
Dealer or the Garmin web site (www.garmin.com) for
availability.
To access the Interface Setup page:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Interface icon to open the Interface
Setup page.
Rino® 520/530 Owner’s Manual
The available interface formats are:
Garmin—The proprietary format used to exchange
waypoint, track, and map data with a PC. Use this setting
for transferring data when using a MapSource product.
Garmin DGPS—Allows DGPS input using a Garmin
beacon receiver and a standard RTCM SC-104 and DGPS
tuning.
NMEA In/NMEA Out—Supports the output of standard
NMEA 0183 version 3.01 data. Use this for real-time
plotting with MapSource or third party programs.
Text Out—Allows ASCII text output of location and
velocity information without input capabilities.
RTCM IN—Allows DGPS input using a standard RTCM
SC-104 format without output capabilities.
RTCM In/NMEA Out—Allows DGPS input using a
standard RTCM SC-104 format and supports the output
of standard NMEA 0183 version 3.01 data.
85
UNIT OPERATION > SETUP PAGES
RTCM In/Text Out—Allows DGPS input using a
standard RTCM SC-104 format and simple ASCII text
output of location and velocity information.
None—Provides no interfacing capabilities.
If Garmin DGPS or RTCM In/NMEA Out format
is selected, additional fields are provided to control a
Garmin differential beacon receiver directly from your
unit. Tuning is automatic with Scan or you can enter the
beacon frequency and bit rate when you select User from
the Beacon list to manually tune the receiver. Refer to the
beacon receiver instructions.
Beacon Receiver
Setup Page
To select a serial data format:
1. Highlight the Serial Data Format field and then
press the Thumb Stick In.
2. Highlight an option and then press the Thumb
Stick In to activate it.
86
Rino® 520/530 Owner’s Manual
UNIT OPERATION > PROXIMITY WAYPOINTS
Proximity Waypoints
This feature allows you to establish waypoints that have
alarm circles around at a distance you can specifiy The
alarm helps you to avoid locations that are restricted or
hazardous.
Proximity Waypoints Page
To use Proximity Waypoints:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. Access the Proximity Waypoints Page from the
Main Menu by highlighting the Proximity icon and
pressing In on the Thumb Stick.
2. With the Name field highlighted, press the Thumb
Stick In to display the Find Menu.
Rino® 520/530 Owner’s Manual
3. Select a waypoint from the Waypoints List or
from any other group of map points and press the
Thumb Stick In to display the Information Page
for that item.
4. Highlight the “Use” button at the bottom of the
page and press the Thumb Stick In to place the
point in the list on the Proximity Waypoints Page.
5. Next use the Thumb Stick to highlight the Radius
field if you want to enter a value different than the
default of 1 mile.
6. Highlight the “Proximity Alarms” check box and
press the Thumb Stick In to activate the alarm
feature. When you trigger an alarm, a tone will
sound and a “Near Proximity Point” message
appears. When you move outside the set radius,
a “Leaving Proximity Point” message displays.
When you choose a Contact, the Proximity
location moves each time the contact updates.
7. To remove or review a single entry, press the
Thumb Stick In. To remove all waypoints from
the list, press the Option Menu button and
choose Remove All.
87
UNIT OPERATION > CALENDAR
Calendar
This feature provides you with a daily, weekly, or
monthly calendar. The calendar allows you to view the
following for any chosen location: Sunrise/Sunset time,
moon phase, Hunt and Fish probabilities, and to archive
waypoints for locations you have visited or want to
navigate to.
Options Menu
Calendar Page
To access the Calendar:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select
Calendar. Press the Thumb Stick in and the
current week is displayed.
88
To view the calendar by days, weeks, or
months:
1. Select the Option Menu button and press the
Thumb Stick In to display the Option Menu.
2. Highlight and select Day View, Week View, or
Month View and then press the Thumb Stick In.
To view a different day, week, or month:
Highlight the left or right arrows on either side
of the date and press the Thumb Stick In.
Depending on the view option selected, the left
arrow shows past days, weeks, and months.
The right arrow shows future days, weeks, and
months.
To add a point (location) to a selected date:
1. Select the Option Menu button and press the
Thumb Stick In to display the Option Menu.
2. Highlight and select Add Point to access the Find
Menu.
3. Select a point from one of the categories in the
Find Menu and press the Thumb Stick In to add it
to the Calendar Page for that date.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > CALENDAR
To view information for a point:
1. In the calendar, select the desired date using the
Thumb Stick to display the calendar date page.
2. Highlight the desired point on the page and press
the Thumb Stick In to display the information
page for that point.
To remove a point:
1. In the calendar, select the desired date using the
Thumb Stick to display the calendar date page.
2. Select the Option Menu button and press the
Thumb Stick In to display the Option Menu.
3. Select Remove Points and press the Thumb
Stick In.
4. Select from Older Than...1 Week, 2 Weeks, 3
Weeks, 4 Weeks or Remove All and the press
the Thumb Stick In.
Rino® 520/530 Owner’s Manual
To remove a selected point:
1. In the calendar, select the desired date using the
Thumb Stick to display the calendar date page.
2. Highlight the desired point on the page and press
the Thumb Stick in to display the Information
Page for that point.
3. Highlight Delete button and then press the Thumb
Stick In.
To view Sun and Moon or Hunt and Fish
information for a selected date:
1. In the calendar, select the desired date using the
Thumb Stick to display the calendar date page.
2. Select the Option Menu button and press the
Thumb stick In to display the Option Menu.
3. Select View Sun And Moon or View Hunt And
Fish and press the Thumb Stick In.
89
UNIT OPERATION > ALARM CLOCK
Alarm Clock
Enter a time in the time field and
turn the alarm on and off from the
control field menu. Remember to
enter alarm times in the same time
format (UTC or local) you are
using for your system.
To turn the alarm clock on/off:
1. Use the Thumb Stick to highlight the Alarm
Mode field and then press In to display the
options.
2. Choose On or Off and press the Thumb Stick In.
Alarm Clock Page
To access the Alarm Clock:
1. Press the Main Page button to open the Main
Menu.
2. In the Main Menu, scroll down and select Alarm
Clock.
When you turn the alarm On, an “Alarm Set” message
appears and allows you to turn the unit Off. When the
“Set Time” arrives, the unit switches on and sounds the
alarm beep. Press the Thumb Stick In to silence the
alarm.
To set an alarm clock time:
1. Use the Thumb Stick to highlight the time field
and then press In to display the keyboard.
2. Use the Thumb Stick to enter the desired time,
choose OK, and press In.
90
Rino® 520/530 Owner’s Manual
UNIT OPERATION > CALCULATOR
Calculator
This feature provides you with all the
basic functions of both of standard or
scientific calculator. You can perform
most calculations identified by the
function symbols along the sides of
the keypad and can save the results
Calculator Page
temporarily in the memory. The
memory is cleared either manually or when you turn off
the Rino 520/530.
To change calculator options:
1. Highlight the page Option Menu and press the
Thumb Stick In to display the Scientific/Standard
and Radians/Degrees options.
2. Highlight the option you want to change and then
press the Thumb Stick In.
3. Use the Thumb Stick to move about the
calculator, enter numbers, and perform
calculations.
To access the Calculator:
1. Press Page/Quit button or the Main Page button
to access the Main Menu.
2. In the Main Menu, scroll down and select
Calculator.
Rino® 520/530 Owner’s Manual
91
UNIT OPERATION > STOPWATCH
Stopwatch
This feature allows you to use the
unit as a stopwatch, including using
it as a lap timer. You may also have
the unit record the lap time based
on distance. For example, if you
set the lap distance to one mile, the Stopwatch Page
unit records the time it takes you to
travel one mile.
To access the Stopwatch:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select the
Stopwatch icon.
3. To mark a lap, use the Thumb Stick to highlight
the Lap field and then press In, with the stopwatch
running.
4. Reset the stopwatch when the timer is stopped.
Use the Thumb Stick to highlight the Reset field
and then press In.
Stopwatch Lap Options
You can set the stopwatch to Lap by Distance so that
each time a certain distance has been travelled, the
stopwatch automatically marks a lap. You can enter a
specific lap distance by selecting Set Lap Distance. To
return to manually marking each lap, open the Option
Menu and select the Lap by Button Press option.
To use the Stopwatch:
1. Use the Thumb Stick to highlight the Start field
and then press In.
2. Use the Thumb Stick to highlight the Stop field
and then press In.
92
Rino® 520/530 Owner’s Manual
UNIT OPERATION > SUN & MOON
Sun & Moon
This feature provides you with a
graphic display of both sun and
moon positioning for a certain
date, time and location with times
for sunrise, sunset, moonrise, and
moonset.
To set the location:
Sun & Moon Page
To access the Sun & Moon Page:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select the Sun
& Moon icon.
1. Highlight the Location field and then press the
Thumb Stick In to display the New Location
options list.
2. Highlight the option desired and then press the
Thumb Stick In to activate. If you choose Current
Location the field values displayed on the page
are for your location. If you choose Use Map,
a map page displays. Use the map pointer to
identify the desired location and then press the
Thumb Stick In. If you choose Use Find Menu
follow instructions in the Find section.
To set the date and time:
1. For the Date and Current Time, highlight each
field, then press the Thumb Stick In to begin data
entry of individual characters.
2. To display the current date and time, highlight the
page Option Menu and press the Thumb Stick In
to display Use Current Time and then press the
Thumb Stick In.
Rino® 520/530 Owner’s Manual
93
UNIT OPERATION > HUNT & FISH
Hunt & Fish
To set the location:
This almanac type feature provides
you with a table of predicted best
times for hunting and fishing for a
selected location and date.
Hunt & Fish Page
To access the Hunt & Fish Page:
1. Cycle the Page/Quit button or press the Main
Page button to access the Main Menu.
2. In the Main Menu, scroll down and select the Hunt
& Fish icon.
To set the date:
1. Highlight the date field and then press the
Thumb Stick In to begin data entry of individual
characters.
2. To display the current date, highlight the page
Option Menu and press the Thumb Stick In to
display the Use Current Date option and then
press the Thumb Stick In.
94
1. Highlight the Location field and then press the
Thumb Stick IN to display the New Location
options list.
2. Highlight the option desired and then press
the Thumb Stick In to activate. If you choose
Current Location the field values displayed
on the page reflect the times at your current
location.
3. If you choose Use Map, a map page displays.
Use the map pointer to identify the desired
location and then press the Thumb Stick In. If
you choose Use Find Menu follow instructions
for using the Find Menu.
NOTE: The times displayed are the recognized best
and good times for hunting and fishing. Be certain
that they are not in conflict with state and local game
laws, which may vary from location to location. It is
your responsibility to know and abide by these laws.
Rino® 520/530 Owner’s Manual
UNIT OPERATION > GAMES
Games
The Games Page includes Memory
Race, Geko Smak, Virtua Maze,
Nibbons, Gekoids, Beast Hunt,
Assimilate, Clothesline, and Waypoint
Bomber. Highlight the appropriate
icon and then press the Thumb Stick
Games Menu
In to play the desired game. Brief
instructions are displayed when you start each game. All
players must be on the same channel/code to play games
involving multiple players.
Memory Race
In this GPS game be the first to clear the board by matching
all of the two symbols sets together. Each symbol is in a
square (you can adjust the size) that you need to walk or
travel to. Once your position appears in a square, highlight
Open at the bottom of the screen and press the Thumb Stick
In. Play by yourself or race against others. Press Page/Quit
to exit at any time.
Rino® 520/530 Owner’s Manual
To adjust the Grid Size or Square Size:
1. Highlight the Grid Size or Square Size field and
press In on the Thumb Stick.
2. Choose the desired size and press In.
3. Highlight Start and press In to begin the game.
Geko Smak
Geko Smak is a GPS-based game that features you
as the player piece. In measured rhythm, Gekos will
appear on the screen. Before the Geko disappears, move
toward the Geko and press the Thumb Stick to smack the
Geko with a hammer. If you get the Geko, an “!” mark
displays above the hammer. If not, just a hammer displays
momentarily.
Field size choices are small, medium and large. Small
fields are roughly 20 yards by 30 yards and large fields
are 60 yards by 90 yards (about the size of an American
football field).
The difficulty levels are Easy, Normal and Hard. These
levels determine how often Gekos appear. The pace
quickens and values vary as difficulty levels increase.
Press the Page/Quit button to exit.
95
UNIT OPERATION > GAMES
Nibbons
In this GPS game, you must walk around the board
collecting the flags as they appear. As you walk, your
“tail” grows. You may travel anywhere on the screen
but you cannot walk on your tail, or you lose a life. As
an added challenge, you must also avoid the Skulls that
chase after you.
Gekoids
This game, which can be played without GPS on, is all
about blasting gekoids. The catch is, you are the space
ship and you can survive only when you avoid getting
hit by Gekoids. Before you begin to play, make certain
to choose your game settings. Orient Map “Northwards”
rotates your ship in the center of the map. The map is
stationary and north is always up. Orient Map “Ship Up”
rotates the virtual world around your ship. Your ship
always points Up.
Beast Hunt
The objective is to find and kill the beast with an arrow
before it incinerates you or you fall into one of several
pits while navigating a maze of platforms. You can be
transported by slides that curve or move diagonally.
When you think you know where the beast is press the
Thumb Stick In to initiate aiming when you are in an
adjacent spot. With the Thumb Stick, point the arrow
in the direction where you think the beast is and press
the Thumb Stick In to fire. When you lose a game,
the layout of hazards, slides, warning platforms, and
the location of the beast is shown. A scoreboard keeps
track of your wins and losses. Press Page/Quit anytime
during the game for further instructions, to turn the sound
On/Off, or to quit.
Press the Thumb Stick to start and blast away! Press the
Page/Quit button to exit.
96
Rino® 520/530 Owner’s Manual
UNIT OPERATION > GAMES
Assimilation
Think of this as a high-tech game of tag. In this GPS
game team members select the same user symbol and
then attempt to assimilate others into their team by
getting within 30 feet of them and pressing the Talk
button. Press Call to show the score and Page to quit the
game. You can set a time limit so the largest team wins,
or play until the other team is completely assimilated. Set
your own rules and enjoy!
Clothesline
In this GPS game team members select the same user
symbol and then attempt to “hit” or “clothesline” other
players by pressing the Talk button when an opposing
team member is between them. You may also mark a
point and assign it a symbol to be used as a stationary
team member. Wait 30 seconds between attempts. Press
Call to view the score and Page to quit the game.
Rino® 520/530 Owner’s Manual
Waypoint Bomber
In this GPS game, it is good to stay on the move! Two or
more players attempt to “bomb” each other. Move your
cursor around on the map page using your Thumb Stick.
When you think an opponent is close to your cursor,
drop a bomb. The receiving radio shows an “Incoming”
message. If the receiving radio is within the blast circle
(about 45 feet), it displays a message that you have been
hit. You must wait 30 seconds between shots to reload.
Either have a timed game with the winner being the one
with the least amount of hits on their radio, or play until
someone gets a specified number of hits (that person
loses). Press the Page/Quit button to exit.
97
APPENDIX > ABOUT FRS/GMRS RADIO
About FRS/GMRS Radio
FRS Radio
FRS, or Family Radio Service, is a UHF radio frequency
band allocated by the FCC for general public use. The
operating frequency ranges from 462.5625 to 467.7125
MHz, with a maximum transmitting power of one half
watt. FRS radios are small and lightweight, making them
ideally suited for outdoor activities. You can expect your
FRS radio to offer reliable operation at a distance of onemile. If the area between you and another FRS operator
is free of obstructions, operation up to two miles can be
achieved. FRS radios broadcast on one of 14 channels,
each with a specific frequency within the FRS band.
The use of FRS radios does not require a license. FRS
was intended for use by families and small groups as an
inexpensive means of two-way communication. FRS
is intended for use throughout the United States, its
territories and possessions. It may also be used in Canada.
FRS is not approved outside of these areas and
98
may interfere with local government communication
frequencies (fire, police, etc.).
FRS Features
FRS radios also include call functions, squelch codes,
channel scan features, and voice scramble capabilities.
Call functions allow you to push a Call button on the
radio to alert other radios set on the same channel. This
feature generates a call tone and is handy in a noisy
environment where the tone is easier to initially identify
than plain speech.
Squelch codes allow you to selectively block out other
FRS users that are not part of your group. They will still
be talking with others in their own group, but you will not
hear them on your radio. They may or may not hear you
and members of your group on their own radios. Squelch
codes act as a filter, blocking your FRS radio from
hearing other unwanted FRS users. Remember though,
these are public-use frequencies and everyone has a right
to talk or listen in.
Rino® 520/530 Owner’s Manual
APPENDIX > ABOUT FRS/GMRS RADIO
Channel scan allows your FRS radio to scan all FRS
frequencies for signals. After scanning briefly to see what
channels other users are on, set your FRS radios to an
unused channel and enjoy less interference. For greater
privacy, some FRS radios have a voice scramble feature.
This feature causes your message to sound garbled to
other FRS users that are not part of your group. However,
it does not guarantee your conversations will be 100
percent private and secure. Other casual FRS users will
not hear your messages, but users with similar radios or
more technically-oriented users can still monitor your
conversations.
FRS Limitations
If you are operating in an urban environment or in
varying terrain, some features (such as canyons or
mountains) act as obstructions limiting the maximum
reception range of your FRS radio. The UHF FRS
frequencies are “line of sight”, meaning that the signals
do not follow the surface of the earth, but instead radiate
in a straight line from the transmitting antenna. If there
Rino® 520/530 Owner’s Manual
is an obstruction between the transmitting FRS radio and
the receiving FRS radio, the signal will not be received.
Smaller obstructions, such as trees, cars and even crowds
of people cause some loss of signal, resulting in reduced
maximum range.
GMRS Radio
The use of a GMRS (General Mobile Radio Service)
radio requires an FCC license (refer to the Web site
http://www.wireless.fcc.gov/uls/ for details.) No license
is required in Canada to operate on GMRS channels. The
operating frequency of GMRS ranges from 462.550 to
462.725 MHz. GMRS radios can use repeater channels
(15R–22R) and repeater towers to extend the range of
the operation. A repeater tower simultaneously receives
GMRS signals on a 467 MHz frequency and then
rebroadcasts the signal on a 462 MHz frequency. Refer
to the “Frequency Charts” for a complete list of each
channel’s frequency. GMRS repeater channels are not
approved for use by the Canadian government, so they
are disabled on Rino 520/530 units sold in Canada.
99
APPENDIX >SPECIFICATIONS
Specifications
Physical
Case: Fully-gasketed, high-impact plastic alloy,
waterproof to IPX7 standards (waterproof to
one meter for 30 minutes)
Size:
5.1” H x 2.3” W x 1.8” D; 7.5” H with antenna
(13.2 x 5.8 x 4.6 cm; 19 cm with antenna)
Weight: Approx. 10.3 ounces (294 g) with Li-Ion battery
pack; 6.2 ounces (175g) without battery pack
Display: 1.7H x1.3”W; 176 x 220 pixels,
256- color transreflective TFT
Compass: Accuracy; +/- 5 degrees1, resolution ; 1 degree
Performance
GPS Receiver: WAAS Enabled, Differential-ready,
12 parallel channel
Acquisition time:
Cold:
Approx. 15 seconds
Warm:
Approx. 45 seconds
AutoLocate™:
Approx. 5 minutes
Update Rate:
1/second, continuous
GPS Accuracy: <15 meters (49 ft) RMS, 95% typical2
DGPS (USGC) Accuracy: 3–5 meters (10–16 ft), 95%
typical with DGPS corrections3
DGPS (WAAS) Accuracy: <3 meters (10 ft), 95%
typical with DGPS corrections3
Altimeter: Accuracy;+/- 10 feet1, resolution; 1 foot
Velocity Accuracy: 0.05 meter/sec steady state
Temperature Range:
-4° to 140° F (-20° to 60° C) (operating range)
32° to 113° F (0° to +45° C) (charging range)
Dynamics:
Performs to specifications to 6 g’s
Interfaces:
NMEA 0183, RTCM 104 (for DGPS
corrections) and RS-232 for PC
interface. Requires RS232 Cable
Accessory (not included).
Quad-helix
Antenna:
100
Rino® 520/530 Owner’s Manual
APPENDIX > SPECIFICATIONS
Radio
Channels: Ch 8–14 FRS,
Ch 1-7, 15–22 GMRS (FCC license req. in U.S.)
WX 1–7 Weather Radio channels
Codes: 1–38
Range: Up to 2 miles on FRS; up to 14 miles on GMRS
Radio Output Power:
FRS 0.5 W; GMRS 2.0 W or 5.0 W (5.0 W - US
only)
Alkaline battery pack, 0.5, 2.0 W
Recharging Time:
Up to 6 hours for a fully depleted Li-Ion Pack
Specifications are subject to change without notice.
Subject to proper user calibration.
1
Subject to accuracy degradation to 100m 2DRMS under the U.S.
DoD-imposed Selective Availability program.
2
With optional Garmin Differential Beacon Receiver Input (such as
Garmin GBR 23).
3
5, 5, 90 Duty Cycle - 5% receive with audio unmuted, 5%
transmit and 90% standby (receive with audio muted)
4
Power
Input: 8.4 V, 2400mAh, rechargeable 2–cell lithiumion battery pack
Battery Life:
Li-Ion Pack: Up to 16 hours (GMRS 5 watt TX,
GPS On)4
Alkaline Pack: Up to 18 hours (GMRS 2 watt
TX, GPS On)4
Rino® 520/530 Owner’s Manual
101
APPENDIX > ACCESSORIES
Installing Accessories
Standard Accessories Provided with the Unit
Belt Clip Assy.—Attaches to the back of the unit and clips to belt or waistband.
A/C Adapter and Charger—Provides an auxilliary power source and
recharges the lithium-ion battery. (Not shown)
Wrist Strap—Provides a convenient method for carrying the unit.
USB Interface Cable and MapSource Trip and Waypoint Manager CDROM—Provides interface to a PC, USB Divers and mapping data management.
Owner’s Manual—Detailed operation reference. (Not shown)
Quick Start Guide—Abbreviated overview of unit operation. (Not shown)
Wrist Strap Installation
USB Cable
Mini USB Port
RS232 Cable
Headset Connector
Port
Optional Accessories
12-volt Adapter Cable—Provides power from an automobile cigarette lighter.
Spare Li-Ion Battery Pack—can replace the included lithium-ion battery pack.
Alkaline Battery Pack—Uses 4 “AA” Alkaline or NiCad batteries. (Not shown)
Carrying Case—Protects the Rino from dust and damage. (Not shown)
Earbud with PTT (Push To Talk) Mic—Earbud and clip-on mic w/PTT button.
Flexible Ear Receiver—Comfortable earpiece for better hearing ability.
Headset with VOX Boom Mic—Utilizes the Rino’s VOX (Voice Operated
Transmission) feature.
PC RS-232 Data Cable —Required for transfer of NMEA interface data.
Automotive Mount—Allows you to mount your Rino on most smooth
surfaces and automotive windshields. (Not shown)
Bicycle Mount—Allows you to mount your Rino on a handlebar. (Not shown)
Neck Lanyard—Allows you to carry the Rino around your neck. (Not shown)
To obtain accessories, see your local dealer or visit the Garmin web site at
www.garmin.com.
102
VOX Headset
Belt Clip Button
(attaches to back
of unit)
Earbud
Belt Clip
(attaches to belt or
waistband)
Lithium-Ion Battery
Pack
Earbud w/PTT
Battery Charger
(Clips onto Battery
Pack)
Alternate Wrist Strap
Attachment Point
12 V DC Adapter
A/C or D/C Power
Adapter Connector
Rino® 520/530 Owner’s Manual
APPENDIX > TRANSFERRING MAPSOURCE DATA
Transferring MapSource Data
If you have purchased a Garmin MapSource Data
program you may want to transfer detailed map data
before beginning use. The Rino 520/530 accepts up to
56 MB of map data from most MapSource products. It
is not possible to transfer thirrd party maps into Garmin
products.
You cannot view multiple types of MapSource data in the
same location at the same time (one replaces the other if
there is an overlap). When you leave a CitySelect area
for example, and enter the area of a topographic map,
the display changes to contour lines. The same is true
when moving from a topo map to a CitySelect map. The
BlueChart maps are at the top of the hierarchy and will
replace any other map information. Here is the list of the
hierarchy of Rino compatible maps for your reference:
1.
3.
5.
7.
BlueChart
MetroGuide
Points of Interest
U.S. Topo
Rino® 520/530 Owner’s Manual
2. City Select
4. Fishing Hot Spots
6. U.S. Waterways & Lights
8. Roads and Recreation
9. WorldMap
Map data transfer requires the use of a PC, a Garmin
MapSource Data Disk, and the PC Interface Cable with USB
port connector supplied with this unit. Follow instructions for
data transfer in the MapSource User’s Manual.
To set up for data transfer:
1. Before attaching the data cable to your PC, install
the Trips and Waypoints Manager CD-ROM
provided with your unit. It also installs USB drivers
specifically needed to communicate with your Rino.
2. Remove the Data Port cover on the back of the
unit by lifting up on the protective cover on the
back of the unit.
3. Connect the Mini-USB connector on the cable to
the PC USB port.
4. Connect the remaining Mini USB connector to the
back of the Rino 520/530 by orienting the connector
with the slot on the back of the unit.
5. Turn on the Rino 520/530 and follow instructions
for map data transfer provided in the MapSource
User’s Manual.
103
APPENDIX > TROUBLESHOOTING GUIDE
Radio Troubleshooting Guide
Symbol
Probable Cause
Remedy
Radio not transmitting
Talk key may not be fully depressed.
Press and hold Talk key until done talking.
FRS/GMRS Radio feature not on or battery low..
Turn radio on or recharge battery..
Messages not being received by others.
Incorrect Channel/Code setting
Make sure other radios are on the same channel, code and scramble.
Out of range or obstructed.
Decrease distance between radios. Adjust Squelch setting.
Limited talk range.
Natural or man-made obstructions can decrease
range.
Decrease distance between radios or obtain a better line of sight
between radios. If GMRS, power may be set too low..
You can hear others, but they cannot hear
you, or you see an incoming transmission, but
nothing is heard.
You are on the same channel, but a different Code.
If you are using Code zero (0), you will hear all transmissions on that
channel. Use the same Code (1-38) as the other party or use Scan to
Find what Code they are using.
Message garbled.
Scramble option is enabled.
Both radios need to have this feature set the same.
Too many unwanted conversations being heard.
Too many users on channel or Code is set to zero.
Switch to a different channel and/or different Code other than zero
(1–38).
Interference or static.
Radios too far apart or too close. Obstructions in
radio line of sight.
Keep radios at least 3 feet apart. Obtain a better line of sight between
radios. Also, try increasing the squelch to accept only strong signals.
Interference from other electronics.
Shut off other devices or move to a different area.
Cannot transmit location.
Could be one of a few things: Your view of the
satellite is obstructed and a GPS fix is not available.
Send Location is off. 30 seconds have not elapsed
since last location transmission. GPS is set to off.
Move to a location with a clear view of the sky. Enable Send Location.
Wait 30 seconds between location transmission. Enable GPS.
Only Call and Press To Talk keys work.
Keylock is enabled.
Hold the Page/Quit button for 5 seconds to release key lock.
104
Rino® 520/530 Owner’s Manual
APPENDIX > TROUBLE SHOOTING GUIDE
GPS Troubleshooting Guide
Symptom
Probable Cause
Remedy
Unit does not turn on.
Battery exhausted.
Recharge or replace batteries.
Unit does not turn on, even with new AA batteries.
AA Batteries may be installed backwards.
Reinstall batteries.
You are pressing and releasing the Power button.
You must press and hold the Power button for 2 seconds.
The unit turns on, then turns off.
Battery may be nearly exhausted.
Recharge or replace batteries.
It takes more than 10 minutes to get a location fix
The unit’s view of satellites is obstructed.
Move to a location with a clear view of the sky.
Cannot access a WAAS system satellite after 2 to 5
minutes.
Your view of the satellite is obstructed or you are
located too far from satellites currently in service for the
Americas
Move to a location with a clear view and point the unit
antenna in the direction of the satellite.
System GPS operation is set to something other than
Normal and/or interface setting is set for RTCM.
Set system GPS to Normal and interface to something other
than RTCM. Or simply turn off WAAS.
Cannot obtain a differential position from WAAS
You have not collected enough information from the
WAAS satellite.
Wait up to 5 minutes for the initial collection, then 1–2
minutes afterwards.
Cannot access Point of Interest, Street, or Intersection
Find Lists.
Detailed MapSource map data is not loaded, unlocked,
or not activated.
Load detailed mapping and unlock, or access the Map Setup
Map option and activate the check box.
Cannot view a track being laid down on the map
page when traveling.
The Track Log feature is turned off.
Access the Tracks Page, highlight the On button and press
the Thumb Stick In.
Cannot see the panning arrow on the Map Page
easily.
There is too much map clutter or the scale is such that
map features are too densely displayed.
Use the Map Page Setup Page to reduce map clutter or
change the map scale.
Cannot exit a menu or page by moving the Thumb
Stick to the Left.
Some menus and pages have an “X” (Exit) on-screen
button in the upper right corner.
Highlight the on-screen button and then press the Thumb
Stick In.
Rino® 520/530 Owner’s Manual
105
APPENDIX > RADIO FREQUENCY CHARTS
Radio Frequency Charts
FRS/GMRS Radio Frequency Chart
Channel Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
106
Transmit Frequency (MHz)
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
Receive Frequency (MHz)
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
Channel Description
GMRS Interstitial 1, FRS 1
GMRS Interstitial 2, FRS 2
GMRS Interstitial 3, FRS 3
GMRS Interstitial 4, FRS 4
GMRS Interstitial 5, FRS 5
GMRS Interstitial 6. FRS 6
GMRS Interstitial 7, FRS 7
FRS-8
FRS-9
FRS-10
FRS-11
FRS-12
FRS-13
FRS-14
GMRS Primary 1
GMRS Primary 2
GMRS Primary 3
GMRS Primary 4
GMRS Primary 5
GMRS Primary 6
GMRS Primary 7
GMRS Primary 8
Rino® 520/530 Owner’s Manual
APPENDIX > RADIO FREQUENCY CHARTS
FRS/GMRS Radio Frequency Chart (cont.)
Channel Number
15R
16R
17R
18R
19R
20R
21R
22R
Transmit Frequency (MHz)
467.5500
467.5750
467.6000
467.6250
467.6500
467.6750
467.7000
467.7250
Receive Frequency (MHz)
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
Channel Description
GMRS Repeater 1
GMRS Repeater 2
GMRS Repeater 3
GMRS Repeater 4
GMRS Repeater 5
GMRS Repeater 6
GMRS Repeater 7
GMRS Repeater 8
Weather Radio Frequency Chart
Channel Number
WX 1
WX 2
WX 3
WX 4
WX 5
WX 6
WX 7
Receive Frequency (MHz)
162.550
162.400
162.475
162.425
162.450
162.500
162.525
Rino® 520/530 Owner’s Manual
Channel Description
NOAA 1 (Weather Radio)
NOAA 2 (Weather Radio)
NOAA 3 (Weather Radio)
NOAA 4 (Weather Radio)
NOAA 5 (Weather Radio)
NOAA 6 (Weather Radio)
NOAA 7 (Weather Radio)
NOTE: For use in countries outside of the U.S. or
Canada, please check with
that government for any
restrictions on FRS or GMRS
use.
107
APPENDIX > RADIO FREQUENCY CHARTS
CTCSS Frequency Chart for the Rino
Code Number Frequency (Hz)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
108
199.5
67
71.9
74.4
77
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100
103.5
107.2
110.9
114.8
118.8
123
Code Number Frequency (Hz)
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
127.3
131.8
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
Code Number Frequency (Hz)
38
250.3
NOTE: If you plan to purchase FRS
radios from third party manufacurers
be aware that there are Continuous
Tone Controlled Squelch System
(CTCSS) differences in some radios.
Some of the tones on one radio may
not be available on other radios.
Charts showing the different Squelch
Codes and manufacturers can be
located on the Internet.
Rino® 520/530 Owner’s Manual
APPENDIX > DATA FIELD DEFINITIONS
Data Field Definitions
minute. (Altimeter Page Only.)
The following data field options are available on the Map,
Navigation, Altimeter, and Trip Computer Pages.
Descent-Total—The total distance descended. (Altimeter Page
Only.)
Accuracy GPS—The estimated accuracy of the GPS signal.
Distance to Destination—The remaining distance to your next
waypoint.
Ambient Pressure—Actual pressure at unit location. (Altimeter
Page Only.)
Distance to Next—The distance to next waypoint on your route.
Ascent-Average—The average vertical distance of ascents.
(Altimeter Page Only.)
ETA at Destination—The estimated time of arrival at your
destination, if you maintain your current speed and course.
Ascent-Maximum—The maximum ascent rate in feet per minute.
(Altimeter Page Only.)
ETA at Next—The estimated time of day you will arrive at your
next waypoint.
Ascent-Total—The total distance ascended. (Altimeter Page
Only.)
Barometer—Ambient pressure relative to sea level. (Rino 530
Altimeter Page Only.)
Bearing—The direction from your current location to a
destination.
Course—The direction from your starting location to a
destination.
Descent-Average —The average vertical distance of descents.
(Altimeter Page Only.)
Descent-Maximum—The maximum descent rate in feet per
Rino® 520/530 Owner’s Manual
Elevation—The altitude (height) above or below sea level.
Elevation-Average—The average elevation achieved. (Altimeter
Page only)
Elevation-Maximum—The highest elevation reached. (Altimeter
Page only)
Glide Ratio—The ratio of horizontal distance traveled to vertical
distance.
Glide Ratio Dest—The glide ratio required to descend from your
present position to the destination’s elevation.
Heading—Your direction of travel as indicated by a compass, in
degrees or cardinal letters (N,S,E,W).
109
APPENDIX > DATA FIELD DEFINITIONS
Odometer—A running tally of distance travelled, based upon the
distance between second-by-second position readings.
Time to Next—The time remaining before you reach the next
point on a route.
Off Course—The distance left or right you are from the original
course (path of travel).
To Course—The compass direction you must go in order to get
back to the original course.
Pointer—Indicates the direction to the next destination.
Trip Odometer—A running tally of distance travelled since last reset.
Speed—Display rate of travel in miles per hour, kilometers per
hour, or nautical miles per hour.
Trip Time–Moving—A running tally of movement time elapsed
since last reset.
Speed-Maximum—The maximum speed the unit has moved.
Trip Time–Stopped—A running tally of stopped time elapsed
since last reset.
Speed-Moving Avg.—Average speed of the unit while moving.
Speed-Overall Avg.—Your average speed.
Sunrise—The time at which the sun rises on this day.
Sunset—The time at which the sun sets on this day.
Temperature—The current outside (ambient) temperature as
measured by the sensor contained in the lithium-ion battery pack.
For best accuracy allow the unit to adjust to ambient temperature
when it has been in a warmer/colder environment such as indoors,
an auto, in direct sunlight, or held with your hand around the
battery. (Temperature is not available while the battery is charging.)
Time of Day—The time for the selected time zone.
Time to Destination—The time remaining before your reach your
destination.
Trip Time–Total—A running tally of all time since last reset.
Turn—The angle difference (in degrees) between the bearing to
your destination and your current line of travel. L means turn Left.
R means turn Right.
Velocity Made Good—The speed at which you are closing on a
destination along a desired course.
Vertical Speed—Your rate of altitude gain/loss over time.
Vertical Speed To Destination—The measurement of your rate of
ascent/descent to a predetermined altitude.
Waypoint at Destination—Indicates the name of the destination
waypoint.
Waypoint at Next—Indicates the next waypoint on a route.
APPENDIX > INTERFACE INFORMATION
Interface Information
Interface formats are selected in the Setup Interface Page.
See also the “MapSource Setup” section of this Appendix
for information on using the Rino 520/530 with MapSource.
The input/output lines on your Rino 520/530 unit can be
made RS232 compatible by using the optional RS232 PC
Interface Cable accessory available from Garmin, in order
to interface to a wide range of external devices, including
PCs, differential beacon receivers, marine autopilots, or a
second GPS receiver. Refer to the Garmin web site www.
garmin.com for the RS232 Cable Accessory ordering
information.
GARMIN Proprietary Sentences:
PGRME (estimated error), PGRMM (datum string),
PGRMZ (altitude), PSLIB (beacon receiver control)
DGPS (Differential GPS) corrections are accepted in
RTCM-SC-104 version 2.0 format through the ‘Data
IN’ line. The Garmin GBR 21 and GBR 23 are the
recommended beacon receivers for use with the Rino
520/530. Other beacon receivers with the correct RTCM
format may be used, but may not correctly display status
or allow tuning control from the GPS unit.
The NMEA 0183 version 3.01 interface format is
supported by the Rino 520/530 and enables the unit to
drive up to three NMEA devices.
NMEA 0183 Version 3.01 Approved Sentences:
GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC,
GPRTE, GPVTG, GPWPL, GPBOD
111
Rino® 520/530 Owner’s Manual
APPENDIX > FCC COMPLIANCE INFORMATION
FCC Compliance Information
The Rino 520/530 complies with Part 15 of the FCC
regulations and with Canadian RSS-210 and ICES-003
for Class B digital devices. Operation of this device is
subject to the following conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation.
This equipment generates, uses, and can radiate radio
frequency energy and may cause harmful interference
to radio communications if not installed and used in
accordance with the instructions. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
112
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet that is on a
different circuit than the receiver’s circuit.
• Consult the dealer or an experienced radio/TV
technician for help.
The Rino 520/530 does not contain any user-serviceable
parts. Repairs should only be made by an authorized
Garmin service center. Unauthorized repairs or
modifications could result in permanent damage to the
equipment and void your warranty and your authority to
operate this device.
Rino® 520/530 Owner’s Manual
APPENDIX > FCC LICENSING INFORMATION
FCC Licensing Information
The Rino 520/530 two-way radio operates on General
Mobile Radio Service (GMRS) frequencies regulated by
the Federal Communications Commission (FCC) in the
United States. Operation on the GMRS frequencies is
subject to additional rules as specified in 47 CFR Part 95.
In order to transmit on GMRS frequencies, you are
required to obtain a license from the FCC. An individual
18 years of age or older, who is not a representative of
a foreign government, is eligible to apply for a GMRS
license. To apply for a GMRS license, you will need FCC
Form 605 (605 Main Form and Schedule F) and FCC
Form 159. You can download the application forms from
the FCC web site at http://www.fcc.gov/Forms/. You
can also request them through the FCC forms hotline at
1-800-418-FORM (1-800-418-3676). You can file Form
605 online at http://wireless.fcc.gov/uls/. A filing fee,
which may change from time to time, is associated with
this application.
Rino® 520/530 Owner’s Manual
For information on fees, see the FCC fee information
web page at http://wireless.fcc.gov/feesforms/index.html.
General information may be found at http://wireless.fcc.
gov/services/personal/generalmobile/.
For questions concerning the license application, contact
the FCC at 1-888-Call-FCC (1-888-225-5322)
No license is required to operate on GMRS channels
in Canada. However, GMRS repeater channels are not
approved for use by the Canadian government.
For use in countries outside of the U.S. and Canada,
please check with that government for any restrictions of
FRS or GMRS use.
113
APPENDIX > LIMITED WARRANTY
Limited Warranty
This Garmin product is warranted to be free from defects
in materials or workmanship for one year from the date
of purchase. Within this period, Garmin will at its sole
option repair or replace any components that fail in
normal use. Such repairs or replacement will be made at
no charge to the customer for parts or labor, provided that
the customer shall be responsible for any transportation
cost. This warranty does not cover failures due to abuse,
misuse, accident or unauthorized alteration or repairs.
THE WARRANTIES AND REMEDIES CONTAINED
HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED OR
STATUTORY, INCLUDING ANY LIABILITY ARISING
UNDER ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE,
STATUTORY OR OTHERWISE. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH
MAY VARY FROM STATE TO STATE.
114
IN NO EVENT SHALL GARMIN BE LIABLE
FOR ANY INCIDENTAL, SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES, WHETHER
RESULTING FROM THE USE, MISUSE, OR
INABILITY TO USE THIS PRODUCT OR FROM
DEFECTS IN THE PRODUCT. Some states do not allow
the exclusion of incidental or consequential damages, so
the above limitations may not apply to you.
Garmin retains the exclusive right to repair or replace
the unit or software or offer a full refund of the purchase
price at its sole discretion. SUCH REMEDY SHALL BE
YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY
BREACH OF WARRANTY.
To obtain warranty service, contact your local Garmin
authorized dealer or call Garmin Product Support for
shipping instructions and an RMA tracking number.
The unit should be securely packed with the tracking
number clearly written on the outside of the package. The
unit should then be sent, freight charges prepaid, to any
Garmin warranty service station. A copy of the original
Rino® 520/530 Owner’s Manual
APPENDIX > LIMITED WARRANTY
sales receipt is required as the proof of purchase for
warranty repairs.
Garmin International, Inc.
1200 E 151st Street, Olathe, Kansas 66062 U.S.A.
Tel. 913/397.8200
Fax. 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate,
Romsey, SO51 9DL U.K.
Tel. 44/0870.8501241
Fax 44/0870.8501251
Online Auction Purchases: Products sold through online
auctions are not eligible for rebates or other special
offers from Garmin. Online auction confirmations are not
accepted for warranty verification. To obtain warranty
service, an original or copy of the sales receipt from
the original retailer is required. Garmin will not replace
missing components from any package purchased through
an online auction.
Rino® 520/530 Owner’s Manual
International Purchases: A separate warranty is
provided by international distributors for units purchased
outside the United States. This warranty is provided
by the local in-country distributor and this distributor
provides local service for your unit. Distributor
warranties are only valid in the area of intended
distribution. Units purchased in the United States or
Canada must be returned to the Garmin service center
in the United Kingdom, the United States, Canada, or
Taiwan for service.
The Garmin Rino 520/530 has no user-serviceable parts.
Should you ever encounter a problem with your unit,
please take it to an authorized Garmin dealer for repairs.
The Rino 520/530 is fastened shut with screws. Any
attempt to open the case to change or modify the unit
in any way will void your warranty and may result in
permanent damage to the equipment.
115
APPENDIX > SOFTWARE LICENSE AGREEMENT
Software License Agreement
Product Registration
Garmin grants you a limited license to use the software embedded
in this device (the “Software”) in binary executable form in the
normal operation of the product. Title, ownership rights, and
intellectual property rights in and to the Software remain in
Garmin.
Use this area to record the serial number (8-digit number located in
the battery compartment) in case your Rino 520/530 is lost, stolen,
or needs service. Be sure to keep your original sales receipt in a
safe place or attach a photocopy inside the manual.
BY USING THE RINO 520/530, YOU AGREE TO BE BOUND
BY THE TERMS AND CONDITIONS OF THE FOLLOWING
SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS
AGREEMENT CAREFULLY.
You acknowledge that the Software is the property of Garmin and
is protected under the United States of America copyright laws
and international copyright treaties. You further acknowledge
that the structure, organization, and code of the Software are
valuable trade secrets of Garmin and that the Software in source
code form remains a valuable trade secret of Garmin. You agree
not to decompile, disassemble, modify, reverse assemble, reverse
engineer, or reduce to human readable form the Software or any
part thereof or create any derivative works based on the Software.
You agree not to export or re-export the Software to any country
in violation of the export control laws of the United States of
America.
116
Help us better support you by completing our online registration
today! Have the serial number of your Rino 520/530 handy and
connect to our Web site (http://www.garmin.com). Look for the
Product Registration link on our Home page.
Serial Number: ___ ___ ___ ___ ___ ___ ___ ___
Contact Garmin
If you should encounter any difficulty while using your Rino
520/530, or if you have any questions, in the U.S.A. contact
Garmin Product Support by phone: 913/397.8200 or 800/800.1020,
Monday–Friday, 8 AM–5 PM Central Time; or by e-mail at
sales@garmin.com. In Europe, contact Garmin (Europe) Ltd. at
44/0870.8501241.
Rino® 520/530 Owner’s Manual
INDEX
INDEX
A
Accessories 102
Accuracy 100
Acquisition time 100
Address 60
Add to Route 53, 59
Alarm 90
Alarm Clock 90
Altimeter Page 37
Altitude 37
Arriving at Destination 63
Arrow, Panning 27
Ascent 37, 109
Auto Zoom 30
B
Barometric Pressure 38, 39
Basemap 1
Battery icon 6
Battery Life 101
Bearing 32
Bearing Pointer 32, 34
BlueChart 103
Rino® 520/530 Owner’s Manual
Bread Crumb Trail 64
C
Calculator 91
Calendar 88
Calibrating the Altimeter 41
Calibrating the Compass 35
Call 98
Call Tone 16
CDI 33
Channel 10
City 56
Code 10
Compass
Calibrate 35
Contact 20, 55
Course Deviation Indicator 33
Course Pointer 33, 34
CTCSS 10, 108
Current location 48
D
Data Fields 34, 40, 41
Definitions 109
Data Transfer 103
Defaults 4, 26, 34, 38, 47,
70, 76
Delete Waypoint 51
Descent 37, 109
DGPS 111
E
Editing
Routes 69
Waypoints 50
Electronic Compass 36
Elevation 37, 38, 39
Cchanges 39
Changes 37
Plot 39
Exit 57
F
Family Radio Service 1, 98
FCC 98
License 99
Finding
By name 52, 53
Contact 54, 55
Intersection 61
Point of Interest 58
FRS 7, 10, 108
G
Games 95
Garmin sentences 111
General Mobile Radio Service 1
GMRS 1, 7, 10, 14, 98
Goto 53, 54, 55, 56, 57, 63
GPS
On/Off 18, 44
Status 18
GRI chain 81
H
Headset 15
Hunt & Fish 53, 59, 94
I
Initialize 8
Interface formats 111
Intersection 60, 61
L
Lap 92
License Agreement 116
Line of sight 99
Lock
Buttons/Keys 5
Direction 35
117
INDEX
on Road 30
LORAN TD Format 81
M
Main Display Pages 4
Main Menu Page 42
MapSource 1, 24, 60, 85
Setup 94
Map Data 31, 60, 103
Map Detail 30
Map Page
Options 26
Pan Map 26
Restore Defaults 26
Setup Map 26, 28, 29
Map Pointer 27
Mark Waypoint 48
Measure Distance 26, 31
Message Tone 16
Microphone 15
Monitor Channels 12
My ID 8
N
Name 8
Navigate 33, 73
118
Navigation Page 32
Options 34
Restore Defaults 34
New Contact 20
New Location 45, 46
NMEA 0183 111
North Heading 30
North Up 30, 45, 46
O
Operating the Rino 5
Options Menu 5
Orientation 30
P
Pan Map 26, 27
Pan Plot 40
PC 103, 111
PC Interface Cable 103
Peer-to-Peer 14, 20
PIT 15
Points of Interest 58, 59, 103
Pressure 39
Changes 37
Plot 38, 39
View Plot 39
Programming the Data Fields
28
Project Waypoint 35, 53, 59
Proximity Waypoints 87
R
Radio 17
Radio Page 7
Status Window 18
Weather Radio 17
Re-Sight 35
Recently Found Places 62
Restore Defaults 26, 38, 47
Reverse Route 69
Review Route 70
Ring Tone 16
Roger Tone 16
Routes 68
Copy 70
Create 68
Delete 70
Edit 69
Navigate 73
Remove waypoints 69
Restore defaults 70
Reverse 69
Review 70
S
Satellite Page 43
Scanlist 12, 13, 16
Scan Channels 12, 99
Scan Codes 12
Scramble 14, 99
Sending a Location 23
Setup
Map 26, 28, 29
Scanlist 16
TD field 81
Tones 16
Shortcut Menu 5, 48
Show Data Fields 34
Sight ‘N Go 34, 35
Signal Strength 43
Sky View 43
Specifications 94
Squelch codes 10, 98
Status Bar Overview 6
Status Indicators 19
Stopwatch 92
Stop Navigation 26, 34
Sun & Moon 53, 59, 93
Rino® 520/530 Owner’s Manual
INDEX
Symbol 8, 9
T
Thumb Stick 2, 5
Tones 16
Call 16
Ring 16
Roger 16
Setup 16
Topo map 103
TracBack 65
Track
Log 64
Points 30
Track Up 30, 45, 46
Transmit Location 20, 23
Trip Computer Page 47
Two-way Radio 1, 98, 113
U
15
Voice Scramble 99
VOX 15
W
WAAS 44, 76
Waterproof 1, 100
Waypoint 48, 49
Create 48
Delete 51
Edit 50
Move 51
Weather Alert 17
Weather Radio 17, 63
Z
Zoom 25, 30
Ranges 38, 39
Altimeter Page 38
UHF 98
Units Page 78, 81
Unlock Buttons 5
V
Vibrate 16
Voice Operated Transmission
Rino® 520/530 Owner’s Manual
119
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin web site at www.garmin.com.
© Copyright 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00548-00 Rev. B