PowerLite® 85+/825+/826W+
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Microphone
Connect a dynamic or condenser microphone to the Mic port, using a 3.5 mm
mini-jack cable.
NOTE: If you’re using a condenser microphone, set the Plug-in Power setting
to On. See the User’s Guide on your projector CD for more information.
Turn on your equipment
3
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
1
2
Turn on your computer or video source.
Plug in the projector.
Focus
Zoom
Connect the projector
Choose from the following connections:
Computer Monitor Port
3
Open the A/V Mute slide all the way.
Connect a computer using the VGA cable that came with the projector.
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Using the remote control
Video Player
Connect up to 4 video devices and use the remote control to switch between
them.
Component-toVGA cable
(optional)
S-Video
RCA video cable
cable
(composite video)
(optional)
(optional)
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Audio cable
(optional)
Power light
Connect one end to the projector’s Computer1 or Computer2 port, and the
other end to your computer’s
monitor port. If you are using a notebook,
switch it to external display. You can also connect an audio cable to the
Audio1 or Audio2 port.
Power button
Computer USB Port
The
power light flashes green, then stays on.
Turn projector
on and off
NOTE: To shut down the projector, press the
power button twice, wait for
the two confirmation beeps, then unplug it. You don’t have to wait for the
projector to cool down.
Connect a computer (Windows® 2000 SP4 or later or Mac OS® X 10.5.1-10.6)
using the USB cable that came with the projector.
Choose which
source to display
Turn off projector
display and sound
Connect the square end of the USB cable to the projector’s
TypeB
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. Then turn on your projector (see “Turn on your equipment”). You
can also connect an audio cable to the Audio2 port.
Adjust the image
Camera or USB Device
1
Connect a digital camera, document camera (Epson DC-06 document camera),
or other USB device to the projector’s
TypeA (flat) USB port.
Change
presentation
slides (USB cable
connection only)
If you don’t see an image, press the Source Search button on the
projector or remote control to select the image source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
Open a menu item
assigned by the user
Control projector volume
Navigate
projector
menus
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see the User’s Guide on your projector CD.
Follow the on-screen instructions to install the Epson USB Display software
(with Mac OS X, first double-click the USB Display Installer icon that appears
on your computer screen). Then press the USB button on the remote control.
(You need to install the software only the first time you connect.)
Network (LAN)
Connect the projector to your network using an Ethernet® cable. See “Project
Over the Network” on the back of this sheet for more information.
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature to present JPEG images. See the User’s Guide on
your projector CD.
For information on playing sound through the projector or connecting an
external monitor, see the User’s Guide on your projector CD.
4118552
1-F
Rev.0
C
4118552
1-F
Rev.0
M
4118552
1-F
Rev.0
Y
4118552
1-F
Rev.0
K
PowerLite® 85+/825+/826W+
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Microphone
Connect a dynamic or condenser microphone to the Mic port, using a 3.5 mm
mini-jack cable.
NOTE: If you’re using a condenser microphone, set the Plug-in Power setting
to On. See the User’s Guide on your projector CD for more information.
Turn on your equipment
3
Turn the focus ring to sharpen the image.
Turn the zoom ring to reduce or enlarge the image.
1
2
Turn on your computer or video source.
Plug in the projector.
Focus
Zoom
Connect the projector
Choose from the following connections:
Computer Monitor Port
3
Open the A/V Mute slide all the way.
Connect a computer using the VGA cable that came with the projector.
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Using the remote control
Video Player
Connect up to 4 video devices and use the remote control to switch between
them.
Component-toVGA cable
(optional)
S-Video
RCA video cable
cable
(composite video)
(optional)
(optional)
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Audio cable
(optional)
Power light
Connect one end to the projector’s Computer1 or Computer2 port, and the
other end to your computer’s
monitor port. If you are using a notebook,
switch it to external display. You can also connect an audio cable to the
Audio1 or Audio2 port.
Power button
Computer USB Port
The
power light flashes green, then stays on.
Turn projector
on and off
NOTE: To shut down the projector, press the
power button twice, wait for
the two confirmation beeps, then unplug it. You don’t have to wait for the
projector to cool down.
Connect a computer (Windows® 2000 SP4 or later or Mac OS® X 10.5.1-10.6)
using the USB cable that came with the projector.
Choose which
source to display
Turn off projector
display and sound
Connect the square end of the USB cable to the projector’s
TypeB
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. Then turn on your projector (see “Turn on your equipment”). You
can also connect an audio cable to the Audio2 port.
Adjust the image
Camera or USB Device
1
Connect a digital camera, document camera (Epson DC-06 document camera),
or other USB device to the projector’s
TypeA (flat) USB port.
Change
presentation
slides (USB cable
connection only)
If you don’t see an image, press the Source Search button on the
projector or remote control to select the image source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
Open a menu item
assigned by the user
Control projector volume
Navigate
projector
menus
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see the User’s Guide on your projector CD.
Follow the on-screen instructions to install the Epson USB Display software
(with Mac OS X, first double-click the USB Display Installer icon that appears
on your computer screen). Then press the USB button on the remote control.
(You need to install the software only the first time you connect.)
Network (LAN)
Connect the projector to your network using an Ethernet® cable. See “Project
Over the Network” on the back of this sheet for more information.
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature to present JPEG images. See the User’s Guide on
your projector CD.
For information on playing sound through the projector or connecting an
external monitor, see the User’s Guide on your projector CD.
4118552
1-F
Rev.0
C
4118552
1-F
Rev.0
M
4118552
1-F
Rev.0
Y
4118552
1-F
Rev.0
K
Network configuration
If you need to configure the projector for your network, you can use the
projector’s menu system.
NOTE: If you’re using the optional Wireless 802.11a/b/g Module, see the
User’s Guide on your projector CD for configuration instructions.
1
Press the Menu button on the remote control, select the Network
menu, then press Enter.
Project over the network
Install EasyMP® Network Projection and EasyMP Monitor (Windows only) on
each computer that will project over the network. Use the CD labeled Epson
Projector Software for Meeting & Monitoring to install the software.
If you need to configure the projector for your network, see “Network
Configuration.”
1
2
Select the Wired LAN menu and press Enter.
3
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer, check the following:
For more information about using the projector, install the manuals from your
projector CD.
•
Telephone Support Services
Select Advanced Connection Mode and click OK.
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
•
Press the Source Search button on the projector or remote control to
select the computer as the image source.
•
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor (allow a few
seconds for the projector to sync up after you press the key). It may be
labelled CRT/LCD or have an icon such as
. You may have to hold
down the Fn key while pressing it.
Start EasyMP Network Projection on your computer.
Mac OS X: Double-click the EasyMP Network Projection icon in your
Applications folder.
Choose Network Configuration and press Enter.
Where to get help
Press the LAN button on the remote control.
Windows: Select
or Start > Programs or All Programs > EPSON
Projector > EasyMP Network Projection > EasyMP Network
Projection V2.XX.
2
3
4
Troubleshooting
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6
Monday through Friday
If the projector and notebook don’t display the same
image...
5
•
If your network assigns addresses automatically, turn on the DHCP
setting.
•
If your network does not assign addresses automatically, turn off
DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
buttons on the remote control to
To enter numbers, use the
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, press
the Esc button to return to the previous menu.
6
To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
7
When you’re done making all necessary changes, press the Esc button
to return to the previous menu, select Complete, and press the Enter
button to save your settings. Then press Enter again to confirm.
8
If you don’t see the projector you want, click the Automatic search
button. If you still don’t see the projector, click the Manual Search
button and enter the projector’s IP address.
Do one of the following:
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
PM,
Pacific Time,
Visit epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson with your questions.
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
Registration
1
From the Windows Control Panel, open the Display utility and select
Settings or Change display settings. In Windows Vista®, right-click on
the desktop and select Personalize, then select Display Settings.
2
3
Select Advanced or Advanced Settings.
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external monitor port is set as your
primary display and/or enabled.
For a list of optional accessories, see the User’s Guide on your projector CD.
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Select the projector you want to connect to, then click Connect.
to 6
Internet Support
Windows
Mac OS X
4
AM
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
Choose IP Settings and press Enter. You see a screen like the
following:
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless 802.11a/b/g Module, you can project
wirelessly. To purchase the Wireless 802.11a/b/g Module or other
accessories, see “Optional Accessories.” For more information about using
the projector on a network, see your User’s Guide and EasyMP Network
Projection Operation Guide on your projector CD.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
Press the Menu button to exit the menu system.
This information is subject to change without notice.
© 2009 Epson America, Inc. 12/09
Printed in XXXXXX
4118552
1-B
Rev.0
C
4118552
1-B
Rev.0
M
4118552
1-B
Rev.0
Y
CPD-27777
4118552
1-B
Rev.0
K
Network configuration
If you need to configure the projector for your network, you can use the
projector’s menu system.
NOTE: If you’re using the optional Wireless 802.11a/b/g Module, see the
User’s Guide on your projector CD for configuration instructions.
1
Press the Menu button on the remote control, select the Network
menu, then press Enter.
Project over the network
Install EasyMP® Network Projection and EasyMP Monitor (Windows only) on
each computer that will project over the network. Use the CD labeled Epson
Projector Software for Meeting & Monitoring to install the software.
If you need to configure the projector for your network, see “Network
Configuration.”
1
2
Select the Wired LAN menu and press Enter.
3
If you see a blank screen...
Manuals
If you see a blank screen or the No signal message after turning on your
computer, check the following:
For more information about using the projector, install the manuals from your
projector CD.
•
Telephone Support Services
Select Advanced Connection Mode and click OK.
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
•
Press the Source Search button on the projector or remote control to
select the computer as the image source.
•
If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor (allow a few
seconds for the projector to sync up after you press the key). It may be
labelled CRT/LCD or have an icon such as
. You may have to hold
down the Fn key while pressing it.
Start EasyMP Network Projection on your computer.
Mac OS X: Double-click the EasyMP Network Projection icon in your
Applications folder.
Choose Network Configuration and press Enter.
Where to get help
Press the LAN button on the remote control.
Windows: Select
or Start > Programs or All Programs > EPSON
Projector > EasyMP Network Projection > EasyMP Network
Projection V2.XX.
2
3
4
Troubleshooting
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6
Monday through Friday
If the projector and notebook don’t display the same
image...
5
•
If your network assigns addresses automatically, turn on the DHCP
setting.
•
If your network does not assign addresses automatically, turn off
DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
buttons on the remote control to
To enter numbers, use the
highlight the number you want to input, then press the Enter button.
When you’re finished entering an address in the network menu, press
the Esc button to return to the previous menu.
6
To prevent the IP address from appearing on the standby screen, set the
IP Address Display setting to Off.
7
When you’re done making all necessary changes, press the Esc button
to return to the previous menu, select Complete, and press the Enter
button to save your settings. Then press Enter again to confirm.
8
If you don’t see the projector you want, click the Automatic search
button. If you still don’t see the projector, click the Manual Search
button and enter the projector’s IP address.
Do one of the following:
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
PM,
Pacific Time,
Visit epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson with your questions.
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
Registration
1
From the Windows Control Panel, open the Display utility and select
Settings or Change display settings. In Windows Vista®, right-click on
the desktop and select Personalize, then select Display Settings.
2
3
Select Advanced or Advanced Settings.
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external monitor port is set as your
primary display and/or enabled.
For a list of optional accessories, see the User’s Guide on your projector CD.
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Select the projector you want to connect to, then click Connect.
to 6
Internet Support
Windows
Mac OS X
4
AM
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
Choose IP Settings and press Enter. You see a screen like the
following:
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: Using the optional Wireless 802.11a/b/g Module, you can project
wirelessly. To purchase the Wireless 802.11a/b/g Module or other
accessories, see “Optional Accessories.” For more information about using
the projector on a network, see your User’s Guide and EasyMP Network
Projection Operation Guide on your projector CD.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
Press the Menu button to exit the menu system.
This information is subject to change without notice.
© 2009 Epson America, Inc. 12/09
Printed in XXXXXX
4118552
1-B
Rev.0
C
4118552
1-B
Rev.0
M
4118552
1-B
Rev.0
Y
CPD-27777
4118552
1-B
Rev.0
K