Owner`s manual | Garmin Legend GPS Receiver User Manual

TM
eTrex Legend
personal navigator
®
owner’s
manual
and
reference
guide
© 2001 GARMIN Corporation
GARMIN International, Inc.
1200 E 151st Street, Olathe, Kansas 66062 U.S.A.
Tel. 913/397.8200
Fax. 913/397.8282
GARMIN (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ U.K.
Tel. 44/1794.519944
Fax.44/1794.519222
GARMIN Corp.
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax. 886/2.2642.9099
All rights reserved. Except as expressly provided herein, no part of this manual may
be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage
medium, for any purpose without prior written consent of GARMIN Corporation.
GARMIN Corporation hereby grants permission to download a single copy of this
manual onto a hard drive or other electronic storage medium to be viewed for personal
use, provided that such electronic or printed copy of this manual contains the complete
text of this copyright notice and provided further that any unauthorized commercial
distribution of this manual is strictly prohibited.
Information in this manual is subject to change without notice. GARMIN Corporation
reserves the right to change or improve its products and to make changes in the
content without obligation to notify any person or organization of such changes.
Visit the GARMIN website (www.garmin.com) for current updates and supplemental
information concerning the use and operation of this and other GARMIN products.
GARMIN, AutoLocate, Personal Navigator, and TracBack are registered trademarks, eTrex
Legend, MapSource, and Click Stick are trademarks of GARMIN Corporation and may
not be used without the express permission of GARMIN Corporation.
June 2001
Part Number 190-00234-00 Rev. B
Printed in Taiwan
SECTION 1
Introduction
About This
Manual
Thank you for choosing the GARMIN eTrex Legend.
To get the most from your new eTrex Legend, take time to
read through this owner’s manual in order to understand
all of the operating features. This manual is organized into
four sections.
The Introduction section provides FCC and safety
information and the Table of Contents.
The Getting Started section introduces you to the
eTrex Legend features, main operating pages and basic
navigation methods.
The Reference section provides details about using
the features of the eTrex Legend according to topic. The
explanations for each feature in this section are divided
into: (1) An overview that discusses the feature and how it
functions and (2) A detailed Step-by-Step instruction for
using the feature.
Reading the overview may be all that you require to
operate features, however, the Step-by-Step instructions
are available, if needed.
The Appendices contain information on items such as
Accessories, Specifications, a Troubleshooting Guide, and
an Index by Subject.
Standard Package Contents:
1 eTrex Legend Unit
1 Carry Lanyard
1 Owner’s Manual
1 Quick Start Guide
1 PC Interface Cable
i
Introduction
FCC Compliance
Statement
This device complies with Part 15 of the FCC limits
for Class B digital devices. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed or used in accordance with the instructions, may
cause harmful interference to radio communications.
There is no guarantee that interference will not occur in
a particular instance. If this equipment does cause harmful interference to other equipment, try to correct the
problem by relocating the equipment.
Consult an authorized GARMIN dealer or other qualified
service technician if the problem cannot be corrected.
Operation is subject to the following conditions: (1) This
device cannot cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
The eTrex Legend does not contain any user-serviceable
parts. Repairs should be made only by an authorized
GARMIN service center. Unauthorized repairs can void
the warranty.
Warnings
and
Precautions
CAUTION: The Global Positioning System (GPS) is operated by the government of the United States, which is
solely responsible for its accuracy and maintenance. The
system is subject to changes which could affect the accuracy and performance of all GPS equipment. Although
the eTrex Legend is a precision electronic NAVigation AID
(NAVAID), any NAVAID can be misused or misinterpreted
and, therefore, become unsafe.
CAUTION: IT IS THE USER’S RESPONSIBILITY TO
USE THIS PRODUCT PRUDENTLY. THIS PRODUCT
IS INTENDED TO BE USED ONLY AS A TRAVEL
AID AND MUST NOT BE USED FOR ANY PURPOSE
REQUIRING PRECISE MEASUREMENT OF DIRECTION, DISTANCE, LOCATION, OR TOPOGRAPHY.
THIS PRODUCT SHOULD NOT BE USED AS AN AID
TO DETERMINE GROUND PROXIMITY FOR AIRCRAFT
NAVIGATION.
ii
Introduction
MAP DATA INFORMATION: One of the goals of
GARMIN is to provide customers with the most complete
and accurate cartography that is available to us at a reasonable cost. We use a combination of governmental and
private data sources, which we identify as required in
product literature and copyright messages displayed to
the consumer. Virtually all data sources contain inaccurate
or incomplete data to some degree. This is particularly
true outside the United States, where complete and accurate digital data is either not available or prohibitively
expensive.
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of the eTrex Legend to secure
the GPS unit so that it will not interfere with the vehicle’s
operating controls, obstruct the driver’s view of driving
conditions, or cause damage or personal injury in the
event of an accident. Do not mount the eTrex Legend over
air bag panels or in the field of air bag deployment. Air
bags expand with a rapid force that can propel objects
in their path toward the driver or passengers causing possible injury. Refer to air bag safety precautions contained
in the vehicle owner’s manual. Do not mount the eTrex
Legend in a place where the driver or passengers are likely
to impact it in an accident or collision. The mounting
hardware provided by GARMIN is not warranted against
collision damage or the consequences thereof.
WARNING: When used in vehicles, it is the sole responsibility of the driver of the vehicle to operate the vehicle
in a safe manner, maintain full surveillance of all driving
conditions at all times, and not become distracted by the
eTrex Legend to the exclusion of safe driving practices.
It is unsafe to operate the controls of the eTrex Legend
while you are driving. Failure by the driver of a vehicle
equipped with an eTrex to pay full attention to operation
of the vehicle and road conditions while the vehicle is
in motion could result in an accident or collision with
property damage and personal injury.
Warnings
and
Precautions
Do Not Place Unsecured
on the Vehicle Dash
Do Not Mount Where
Driver’s Field of Vision
is Blocked
Do Not Mount
Over Air Bag Panels
Do Not Mount in Front of an Air
Bag Field of
Deployment
iii
Introduction
Table of Contents
Section One - Introduction
About This Manual.............................................i
FCC Compliance Statement...............................ii
Warnings and Precautions.............................ii-iii
Table of Contents..............................................iv
Section Two - Getting Started
Setup, Features, & Basic Navigation.....................1
Features and Button Function.............................2
Battery Installation...............................................3
Starting-Up...................................................................3
Backlighting and Contrast...................................4
Map Data Setup...................................................4
Page Basics: The Main Pages.............................5-9
Setting The Correct Time.....................................9
Basic Navigation...........................................10-12
Section Three - Reference
The Satellite Page..........................................13-14
Navigation Methods..........................................15
The Map Page..............................................16-22
Map Page Options..................................17-22
Panning the Map .................................18
Stop Navigation....................................19
Navigation Status..................................19
Data Fields.......................................19-20
Map Page Setup Options.................21-22
The Navigation Page.....................................23-24
Bearing/Course Pointer.........................23
Data Fields...........................................23
Navigation Page Options....................24
The Trip Computer Page....................................25
The Main Menu................................................26
Marking Your Location...............................27
Creating a Waypoint............................27-28
Moving a Waypoint....................................28
iv
Projecting a Waypoint.................................29
Editing Waypoints......................................29
Saving as a Waypoint..................................29
The Find Menu......................................30-36
Finding a Waypoint..............................31
Finding a Favorite..........................31-32
Finding a City.......................................32
Finding an Exit.....................................33
Finding a Point of Interest..........34-35
Finding an Address or Intersection..35-36
Using a Goto................................................36
Routes....................................................37-42
Creating and Using a Route...................37
Editing a Route.................................38-40
Adding or Editing from the Route Map
Page.................................................40-41
Navigating a Route.............................41
Data Fields...........................................42
The Tracks Page.......................................43-44
The Setup Pages......................................45-49
Time Page..............................................45
Units Page.............................................46
Display Page..........................................47
Heading Page.......................................47
Interface Page.......................................48
System Page..........................................49
The Accessory Pages..............................50-52
Sun and Moon Page...............................50
Calendar Page.......................................51
Hunt and Fish Page...............................52
Section Four - Appendices
Appendix A: Specifications...............................53
Appendix B: Time Offset Chart........................54
Appendix C: Accessories..................................55
Appendix D: Wiring Diagram...........................56
Appendix E: Troubleshooting...........................57
Appendix F: Index......................................58-59
Appendix G: Warranty.......................................60
SECTION 2
Before you begin to explore the eTrex Legend’s
operating features, you will want to follow these “Getting
Started” instructions to prepare it for operation by
installing batteries, adjusting the screen contrast, loading
optional GARMIN MapSourceTM mapping data, and setting the correct time for your current location.
The operating features of the unit are structured to
be accessed and activated by pressing buttons on the unit
which is explained on the following page.
The five Main Pages are your primary access to
operating the eTrex Legend. Each page provides either
a basic navigation function or access to features which
enhance navigation or customize the unit’s operation to
meet your requirements.
This “Getting Started” section will introduce you to
the Main Pages and how they are structured. You will also
be shown how to perform basic navigation techniques to
help you start using your eTrex Legend immediately.
Detailed instructions on using the eTrex Legend’s
features and their options are contained in the “Reference”
section.
Features include:
Storage for 500 Waypoints with name and graphic symbol.
An automatic Track Log with storage capability for 10
Tracks with 250 points each.
Route building capability, with storage for 20 Routes with
50 Waypoints each.
A Trip Computer for displaying a variety of navigation
data such as speed, ETA, ETE, heading, odometer, etc.
A Find Feature for locating Waypoints, Cities, Interstate
Exits, Points of Interest, Street Addresses and Intersections.
8 MB of detailed map data storage, allowing transfer from
GARMIN MapSource CD-ROM’s.*
Wide Area Augmentation System (WAAS) capability.**
Getting Started
Setup,
Features,
and
Basic Navigation
* Points of Interest, Address,
and Intersection data must
be transferred to the unit
using a GARMIN MapSource
CD-ROM. See pages 4 and 55
for more information.
** About WAAS
Because the Wide Area Augmentation System (WAAS) is
currently under development
and is not fully supported by
geo-stationary satellites, effective use of the WAAS feature
may be limited by your geographic location in relation to
those satellites now in service.
There are two WAAS satellites
in service in geo-stationary
orbit above the Equator, one
over the Atlantic Ocean and
one over the Pacific Ocean.
Currently, WAAS satellite signal
reception requires an absolute
clear view of the sky and works
best when there are no nearby
obstructions such as buildings,
mountains, etc. In fact, you may
not be able to receive or easily
maintain a WAAS satellite signal
until full satellite support for this
program is complete.
Not enabling WAAS when you
cannot receive a signal will
speed unit map drawing and
conserve battery power.
See page 49 for enabling WAAS
and satellite reception
techniques.
1
Getting Started
Features and
Button
Function
Internal Antenna
The CLICK STICKTM (Five Position Switch)
• Press In and Release to enter highlighted
options and to confirm messages
• Press In and Hold to mark your current
location as a waypoint
• Move Up/Down or Right/Left to move
through lists, highlight fields, on-screen
buttons, icons, enter data or move the map
panning arrow
The PAGE button:
• Press and Release to cycle through main pages
LEGEND
The POWER button:
• Press and Hold to turn the unit On/Off
• Press and Release to toggle display backlighting On/Off
External Power
and
Data Connector
LCD
Display
Power/Data
Connector Cover
The ZOOM IN/OUT buttons:
• Press and Hold to Zoom in and out on the Map Page
• Press and Hold when on the Satellite Page to adjust the
screen contrast
The FIND button:
• Press and Release to access the Find Menu
Carry
Lanyard
Slot
2
Battery
Compartment
Cover
F
NOTE: The eTrex Legend is designed to be
held and operated in the left hand, but it
can be held and operated using the right
hand as well, to suit your preference.
Getting Started
Installing the Batteries
The eTrex Legend operates on two AA batteries
(not included), which are located in the back of the unit.
Rechargeable Alkaline, NiMH, NiCad or
Lithium batteries may also be used.
Stored data will not be lost when
the batteries are removed.
To install batteries:
1. Remove the battery cover on the
back of the unit by turning the D-ring
1/4 turn counter-clockwise and pull.
2. Insert the batteries
observing proper
polarity as shown
at the right.
3. Reinstall the battery
cover by turning the
Battery Compartment
D-ring 1/4 turn
D-ring
Battery Cover
clockwise.
4. Battery capacity is displayed on the Status Bar at the bottom
of the Main Menu. (see pages 9 and 26)
Starting Up Your eTrex Legend
To start up the eTrex Legend, take the unit outside
and find an open area where the built-in antenna has a
clear view of the sky. Hold the unit at a comfortable height
with the antenna pointing up. Press and hold the POWER
button to turn the unit on. You will see the Welcome Page.
Press the PAGE button to acknowledge the copyright and
warning messages and move to the Satellite Page.
F
Battery
Installation
Important Note:
When replacing batteries, use only
new or fully recharged batteries.
Do not mix Alkaline, NiMH,
NiCad or Lithium batteries.
Rechargeable batteries may typically display less capacity than
disposable Alkaline batteries.
Remove the batteries from the
unit if you don’t plan to use it
for several months.
Follow the battery manufacturer’s instructions for proper care
and disposal of used batteries.
Extensive use of backlighting
will reduce battery life.
Using ‘Battery Saver’ or ‘Use
With GPS Off’ mode when not
navigating. Alkaline batteries
can last up to 18 hours.
Starting Up
GPS Receiver Status Message
Satellites Signal Strength
NOTE: When you use the unit for the first
time. It may take up to five minutes to find
your location. After that, it will take about
15 to 45 seconds to locate your position.
When a sufficient number of satellites have been
located the window at the top of the page will display a
“Ready to Navigate” message. If you experience difficulty
in tracking satellites, refer to pages 13 for information
about satellite reception and remedies.
Satellite Page
3
Getting Started
Backlighting
and
Contrast
Press & Release POWER Button
to turn Backlighting On/Off
Display Backlighting and Contrast Set Up
If lighting conditions make it hard for you to see
the display screen, you can adjust the contrast or turn on
the backlight.
To turn on the backlighting:
1. Press and release the POWER button to turn on
the backlight feature from any page on the unit. The
backlight will remain on until the set timeout period is
completed or the POWER button is pressed again.
The unit is factory set to timeout 15 seconds after
the last button press.
To adjust the screen contrast:
1. Use the ZOOM IN or OUT buttons to adjust the
contrast with the Satellite Page displayed.
Use ZOOM IN & OUT Buttons
to Adjust Contrast
Map Data
Setup
GARMIN MapSource
CD-ROM’s offer a variety of
detailed mapping data and
navigation information.
MapSource is also an excellent
medium for storage and safety
backup of Personal Waypoints,
Routes and Saved Tracks.
See your GARMIN Dealer or
visit the GARMIN website at:
www.garmin.com
for
MapSource Product Information.
4
Transferring MapSource Map Data
If you have purchased a GARMIN MapSourceTM CD-ROM
mapping program you may want to transfer detailed map
data before beginning use, to provide your unit with maximum Find features and mapping capability. The eTrex
Legend will accept up to 8 MB of transferred map data
which could include any one MetroGuide, Points of Interest, Fishing Hot Spots, Topographic maps, Roads and Recreation, and WorldMap mapping guides for a maximum of
75 maps.
Map data transfer requires the use of a PC, a GARMIN
MapSource CD-ROM, and the PC Interface Cable with
RS232 serial port connector supplied with this unit. Follow
detailed instructions for data transfer in the MapSource User’s
Manual.
Getting Started
Moving from main page to main page
All of the information you need to operate the eTrex
Legend can be found on five main pages (or display screens).
You can simply press and release the PAGE button to cycle
through the Satellite Page, Map Page, Navigation Page, Trip
Computer and Main Menu Page.
Satellite Page
Map Page
Page Basics:
The Main Pages
Navigation Page Trip Computer
Main Menu
While these five pages provide you with different types
of navigation information, they all share common features like
Option Menus and a Main Page Menu, both of which are
accessed by on-screen buttons. To display these menus, simply
highlight the on-screen button and press in on the CLICK
STICK.
Option Menu Button
Main Page Menu Button
An Option Menu
Main Page Menu
These menus allow you to
access options that provide
additional features or customize
the unit to your preferences. To
exit these and other pop-up type
menus, move the CLICK STICK
to the left or right.
Use to go directly to a Main
Page and as an alternate to
cycling through the Main Pages.
Double click on the on-screen
button to toggle between two
pages.
5
Getting Started
Page Basics:
The Main Pages
Map Page Basics
On-Screen
Page and Option
Menu Buttons
Status Window
Position Icon
Map Scale
Map Features
The Map Page displays your present position and
direction of movement using a triangular ‘Position Icon’
that is centered on the map. As you travel, the map
display leaves a “trail” (track log) of your movements.
The map also displays geographic details such as
rivers, lakes, highways, and towns. The map shown above
displays a higher level of detail than the basemap provided with the unit (i.e. residential streets, parks, etc.),
because GARMIN MapSource data has been downloaded
to the unit using a CD-ROM mapping program.
To allow you to view the map from different perspectives, the scale can be changed from 20 feet to 500 miles.
The ZOOM IN and OUT buttons on the side of the unit
allow you to zoom In or Out on the map. Pressing and
holding these buttons causes the scale to change rapidly
instead of changing in increments. The IN button displays
less area but more map detail, while the OUT button will
show you a larger area with less map detail.
6
A Status Window at the top of the page provides
you with current satellite tracking and position accuracy
information.
Getting Started
Navigation Page Basics
Destination (Waypoint) Name
Straight Line Distance
to the Destination
Page Basics:
The Main Pages
Time to Destination
Bearing Pointer
Selectable Data Fields
Compass Ring
The Navigation Page displays directional information
to guide you to a destination. The Status Window at
the top of the page shows you the name of your destination, the distance, and the time to go. A Bearing Pointer
and Compass Ring are displayed to provide you with
navigational guidance. Two Data Fields are provided, and
can be programmed to display a variety of navigation
data.
To navigate to a destination, simply follow the Bearing
Pointer. The Bearing Pointer will always point directly
to the destination, no matter what your current location
might be.
When you are not on an active Goto, Track or Route
(in other words: not traveling to a recorded destination),
the window at the top of the page will display the status
of the GPS Receiver and the approximate accuracy of your
current position. The Compass Ring will be displayed,
indicating your heading while you are moving, but the
data fields at the bottom of the page will not display
any destination related data, such as Estimated Time of
Arrival, etc.
The Navigation Page
when not on an active Goto,
Track, or Route.
7
Getting Started
Page Basics:
The Main Pages
Trip Computer Page Basics
Selectable Data Fields
The Trip Computer Page displays up to eight different
types of navigation data. Each data field is selectable and
can contain one of many data information options.
By selecting the information options that you prefer
and arranging them in a desired order on the page, you
can customize the Trip Computer Page to meet your
navigation needs.
The Page Options Menu allows you to reset the Trip
Computer data when you are ready to start a new trip.
8
Getting Started
Main Menu Page Basics
Page Basics:
The Main Pages
The Main Menu Page with
Feature Icons
&
Battery Capacity, Time/Date,
and Backlighting Status Bar.
The Main Menu provides you with a directory of the eTrex Legend’s advanced
features. From the Main Menu page you can mark and create new waypoints, find map
items such as cities, interstate exits, addresses, points of interest, etc., create routes, save
track logs, setup system operating features, access and use unit accessories.
Main Menu Pages
Mark Waypoint Page - Allows you to mark and record your current location.
Find Menu - Allows you to Find and Goto a map location or waypoint.
Routes Page - Allows you to create a route to a destination, with waypoints along the way.
Tracks Page - Allows you to save a Track Log and navigate a previous path of travel.
Setup Pages - Allows you to set the time, select units of measure, set display backlighting and contrast, select from heading options, select interfaces to compatible external
devices, and select system operating modes.
Accessories Page - Provides Sun & Moon position data, a Calendar with date and note
capability, and best times for Hunting and Fishing.
To exit these pages, highlight the on-screen ‘X’
button and press in on the CLICK STICK.
Setting the Correct Time
If the time displayed in the field at the bottom of the Main Menu does not match
the time for your current location (time zone), you may need to set the time. Use the
Main Menu to access the Setup Pages, select the Time Icon and then follow instructions
for setting the time on page 45.
9
Getting Started
Basic Navigation
To begin learning how to use your eTrex Legend,
begin by using some basic navigation techniques such as
marking your current location as a waypoint, traveling a
short distance, and then, allowing yourself to be guided
back to where you started.
Marking your Current Location as a Waypoint
The first step in most navigation exercises is to mark
your current location as a waypoint so you can return
to it later.
F
The Mark Waypoint Page displaying your Marked Waypoint,
along with the latitude and longitude and approx. elevation.
On-screen buttons can create
a Direct path (Goto) to the
waypoint, show it on the map
(Map), and confirm your selection as a waypoint (OK).
The Data Entry Keyboard
10
NOTE: The eTrex Legend must be “READY TO
NAVIGATE” before you can Mark a waypoint.
To Mark a Waypoint:
1. Press in and hold the CLICK STICK until the ‘Mark
Waypoint’ Page is displayed. Whenever you hold in on the
CLICK STICK, your current location will be marked as a
new waypoint with a three-digit number assigned.
Before saving it, you can personalize the newly marked
waypoint by changing the numeric designation to a more
meaningful name. You can also give it a map symbol to make it
more recognizable when viewed on the map.
To change the waypoint name:
1. Use the CLICK STICK to highlight the waypoint
name field (001) and then press it in to display
the data entry keyboard.
2. Use the CLICK STICK to highlight the desired characters for your new name and then press it in to
place a character in the data field. The field will automatically move to the next character position.
3. Repeat the process until you have completed the new
name or have reached the character limit for the field.
Then highlight ‘OK’ on the keyboard and then press in on
the CLICK STICK to complete the name entry and close
the keyboard.
Getting Started
To change the waypoint symbol:
1. Use the CLICK STICK to highlight the waypoint
symbol field on the Mark Waypoint Page and then press it
in to display the list of symbols.
2. Use the CLICK STICK to move up and down the list
to highlight the desired symbol and then press it in to
place the symbol in the field on the page.
3. Use the CLICK STICK to highlight the on-screen
‘OK’ button at the bottom of the page and then press it
in to save your new waypoint. The waypoint can be
retrieved later using the Find Menu.
Basic Navigation
Now that you’ve marked your location, you can begin
to practice some basic navigation techniques.
There are two main pages that help you navigate; the
Map Page and the Navigation Page.
The Mark Waypoint Page with
the list of
Map Symbols displayed
Press the PAGE button repeatedly until the Map Page
is displayed. You will see the new waypoint in the center
of the map. If you renamed it, it will display the new
name and a map symbol.
Adjust the map scale to 300 feet by pressing the
ZOOM IN or OUT button on the side of the unit until
the scale in the lower left corner of the map reads 300 ft.
To Use the Map Page:
1. Observe the new waypoint you just marked displayed in
the center of the map.
2. Begin walking or driving around for a few minutes and
then stop. (If in a car, make certain the unit has a clear
view of the sky through the windshield in order to receive
satellite signals.)
3. Observe that your location and movement are shown by the
‘Pointer Icon’ and that your path of travel (a Track) is shown
by a dotted line.
4. You can follow the Track back to the waypoint, but instead we’ll
save time and take a direct route to it using another navigation
tool, called a Goto, as explained on the following page.
The Map Page displaying your
Marked Waypoint and a Track
defining your path of travel.
The Accuracy Circle, surrounding the Position Icon indicates
the accuracy of your position to
within the circumference of the
circle.
11
Getting Started
Basic Navigation
Navigating Back to Your Starting Point
Now we will navigate back to the waypoint you
marked at the beginning of this exercise using the Goto
function.
The Map Page with a Goto line
connecting your location to your
original Marked Waypoint
Going To (Goto) the Marked Waypoint:
1. Press and release the FIND key to display the Find Menu.
2. Use the CLICK STICK to highlight and select ‘Waypoints’ from the list of categories.
3. You will be prompted to select find ‘Nearest’ or find ‘By
Name’. Select ‘Nearest’ and press in on the CLICK STICK
to display the Nearest List.
4. The waypoint you had previously marked and saved
will be on the list. Use the CLICK STICK to highlight the
waypoint and then press in to display the Information Page
for the waypoint.
5. Use the CLICK STICK to highlight the ‘Goto’ onscreen button and then press it in to activate a Goto.
Press the PAGE button until the Navigation Page is
displayed.
Walk in the direction of the bearing pointer until it
points to the top of the compass ring. If it points to the
right, you need to move to the right, if it points left, you
need to move to the left. When it points straight up, you
are on course to your destination. The Goto will provide
you with a direct route back to the waypoint and will not
necessarily follow the track you created.
The Navigation Page with the
Bearing Pointer showing you
the direction to go. The
Compass Ring provides you
with orientation information.
The destination name, distance to the destination, and
time to reach it are displayed in the window at the top
of the screen. Two additional data fields are provided at
the bottom of the page and can be programmed to display
a variety of navigation data such as speed, heading, etc.
When you begin to approach the waypoint, an “Arriving
At Destination” message will appear. You can view your
progress by toggling between the Map and Navigation
Page.
To stop navigation, select ‘Stop Navigation’ from either
the Map or Navigation page’s option menu.
The ‘Stop Navigation’ Option.
12
You have now completed a basic exercise in GPS navigation. As you learn more about the unit’s operation, you will
be able to apply more features to your navigation skills.
SECTION 3
Overview
Because the eTrex Legend relies on satellite signals to
provide you with navigational guidance, the unit’s view of
the sky will determine how fast you achieve navigational
status. GPS signals do not travel through rocks, buildings, people, metal, or heavy tree cover...so keep the unit
in clear view of the sky for best results.
Reference
The Satellite
Page
The Satellite Page provides a picture of satellite signal
tracking and tells you when the unit is ready for navigation.
At least three satellite signals are needed to find your location.
The Skyview graphic represents a view looking up
at the sky from your current location showing satellites
and their assigned numbers. The outer ring represents the
horizon around you and the inner circle an overhead view
of the sky out to a 45o angle from vertical. Signal Strength
Bars for each satellite are shown just below the Skyview.
Satellites and their signals appear as hollow shapes until a
signal is received and then they appear darkened in. The
stronger the signal, the taller the signal bar.
Satellite Page
with 8 Satellites Being Tracked
If the unit cannot initially (when first turned on)
determine its location, it will display a “Poor Satellite
Reception” message with four options. Each offers a brief
explanation when highlighted to guide your decision.
When indoors or where a clear view of the sky is
obstructed or you want to save battery power, select the
‘Use With GPS Off’ option from the Satellite Page Option
Menu. You can enter data, create routes, etc., but cannot
navigate in this mode. You can orient the satellite skyview
by selecting optional ‘Track Up’ (your direction of travel)
or ‘North Up’ with the satellite skyview oriented to the
north. You can manually enter a new, more accurate elevation, if known, to increase position accuracy. If you have
moved more than 600 miles since you last used the unit
you may require use of the ‘New Location’ option which
helps the unit to find itself and speeds acquisition.
Once satellite tracking has been achieved, your
location coordinates and the elevation are shown at the
bottom of the Satellite Page.
There are four initialization
options for the “Poor Satellite
Reception” message.
Satellite Page Options Menu
Highlight the on-screen button
at the top of the page & press
in on the CLICK STICK.
13
Reference
The Satellite
Page
The Satellite Page
Options Menu
“GPS Off”
Message
‘North Up’ Skyview Orientation
Enter new elevation data
‘Use Map’ option for determining your current location.
Step-by-Step Instructions
How to select the ‘Use With GPS Off’ option:
1. Use the CLICK STICK to highlight the Option Menu
button at the top of the page and then press it in to
display the Options Menu.
2. Use the CLICK STICK to highlight the ‘Use With GPS Off’
option and then press it in to activate.
3. Observe that the Satellite Page title block now states
“GPS Off”.
4. The eTrex Legend will now stop tracking satellites
and should not be used for navigation. However, whenever the unit is turned On it returns to GPS operation.
How to select ‘Track Up’ or ‘North Up’:
1. Follow procedures for displaying the Options Menu.
2. Highlight either the ‘Track Up’ or ‘North Up’ option
(depending on which is currently in use), and press
in on the CLICK STICK to activate.
How to enter a new elevation:
1. Use the CLICK STICK to display the Options Menu.
2. Highlight ‘New Elevation’ and then press in
on the CLICK STICK. Observe the highlighted
first character in the elevation field and the numerical
keyboard at the bottom of the Satellite Page.
3. Enter the desired elevation by using the CLICK STICK
to highlight the desired numerals and pressing it in. Highlight ‘OK’ and press in to complete entry.
How to enter a new location:
1. Follow procedures for displaying the Options Menu.
2. Highlight ‘New Location’ and press in on the CLICK
STICK to display choices of ‘Auto’ or ‘Use Map’.
3. If you choose ‘Auto’ the eTrex Legend will determine
your new location automatically.
4. If you choose ‘Use Map’ a map page will appear with
instructions stating, “Point to your approximate location
and press ENTER”. Use the CLICK STICK to move the
map pointer to your location on the map and press it in.
14
Reference
Navigation Methods- Overview
Active Navigation is supported by three of the five
Main Pages:
Navigation
Methods
The Map Page graphically shows you map details,
your current location, your elevation, marks your route to
a destination with a route line, and leaves a trail (track
log) of where you’ve been.
The Navigation Page tells you what direction to go
and the direction you are traveling.
The Trip Computer Page records and displays travel
data, like your speed, the distance you have traveled, or
the distance to travel, and the time of day or the time
remaining before reaching a destination and more.
A Goto
Methods of Navigating using the eTrex Legend
There are four methods of navigating when using the
eTrex Legend and each is graphically displayed on the
Map Page.
Goto - A direct path to a map location (waypoint,
city, address, etc.).
A Track
Track - A previous path of travel that has been stored
(logged) in the eTrex Legend. A Track allows you to
repeat a path or to return to your starting point on the
same path using the GARMIN TrackBack feature.
A Route
Route - A path to a destination consisting of landmarks along the way (waypoints, cities, highway exits,
points of interest, intersections, etc.).
Travel when not on a Goto, Track or Route - This
is best described as travel without entering a destination in the eTrex Legend. The Map Page displays your
real-time movement as you travel with the unit turned
on and receiving satellites.
Travel when not on a Goto,
Track, or Route as indicated
by the ‘Pointer Icon’ and a
dotted line indicating your
path of travel.
15
Reference
The Map Page
The Map Page - Overview
The Map Page shows your present position and
direction of movement, as a triangular ‘Position Icon’, in
the center of the map. As you travel, the map display
leaves a “trail” (track log) of where you’ve been. The map
display also shows the map scale and geographic details
such as lakes, rivers, highways, and towns.
Use the ZOOM IN and OUT buttons to change the
map scale in order to show more map area with less
detail or less map area with more detail. Press and hold to
ZOOM the map scale rapidly.
The Map Page
Position Icon
Map Features
Map Scale
In many instances the map will display an ‘Accuracy
Circle’ surrounding the ‘Position Icon’. The eTrex Legend
uses both map resolution and GPS accuracy in defining
your location to a point within the circle. The smaller
the circle, the more accurate your location. For the most
accurate location information, refer to the Satellite Page.
When using the ‘Pan Map’ feature, a small outline
arrow (Map Pointer) can be moved about the page to
highlight and identify map items or to scroll the map to
view areas not shown on the display screen.
A Status Field at the top of the page provides satellite
tracking and location accuracy information.
Two optional Data fields at the bottom of the page
can be programmed to provide a variety of travel and
navigation information.
Accuracy Circle
Panning Arrow
(Map Pointer)
16
More detailed map features as well as information
about those features can be downloaded to the unit from
a GARMIN MapSource CD-ROM. When using MapSource
data, the word ‘mapsource’ will appear below the map
scale whenever you zoom in to view map details.
The Map Page Options Menu allows you change the
arrangement of page features, stop active navigation, pan
the map, and customize the map itself to display features
in a manner that meets your personal preferences.
Reference
Map Page Options - Overview
Map Page options allow a variety of operating and
custom features for your eTrex Legend.
Map Page
Options Menu
On-screen Map Page
Options Menu button
Not all of the Map Page options are available at the
same time. Many are replaced by an opposite option when
they are selected, such as Hide Data Fields/Show Data
Fields. The Map Page options are:
Pan Map - Allows you to move the Panning Arrow
(Map Pointer) about on the map.
Stop Navigation - Stops navigating to a destination.
Hide Nav Status/Show Nav Status - Removes the
navigation status window to expand the map area or
inserts the navigation status window.
Hide Data Fields/Show Data Fields - Removes or
inserts two programmable data fields at the bottom of
the page and expands or reduces the map area.
Setup Map - Displays the Setup Map Pages, which
allows you to tailor the map to your requirements such
as changing text size, map orientation, and map detail.
Restore Defaults - Returns the Map Page to the
original factory settings (defaults).
Map Page Options Menu
with ‘Pan Map’ selected.
When no active navigation
is being used ‘Stop Navigation’ will appear gray.
If ‘Show Data Fields’ is
selected, it will be replaced
by the ‘Hide Data Fields’
option.
The ‘Setup Map’ option
consists of five sub-pages.
Map Page Options - Step-by Step Instructions
To select a map page option:
1. Highlight the Option Menu on-screen button at the
top of the display screen and then press in on the
CLICK STICK to open the menu.
2. Highlight the desired option on the menu and then press
in on the CLICK STICK to activate the option.
3. To close without making a selection, move the CLICK
STICK to the right
17
Reference
Map Page Options
Using the Panning Arrow - Overview
The Map Page pan function allows you to display an
arrow used to point and identify items on the map, and to
move the map in order to view areas beyond the current
viewing area on the display.
The map panning function is activated from the
options menu on the Map Page. The CLICK STICK
moves the panning arrow (also referred to as the map
pointer) in the desired direction on the map page. If the
arrow moves to the edge of the map display, the map will
also move to reveal more map area. When this occurs,
the map will require some time to redraw the new area
of the map.
Map Page with
Panning Arrow
Highlighted Map Item
Whenever the panning arrow is placed on a map
item, the name of that item will be highlighted. This
features applies to waypoints, roads, lakes, rivers ... nearly
everything that is displayed.
Pressing and releasing the CLICK STICK, marks
the arrow location or the map item information page. An
option menu allows you to: add it to the Favorites list,
add it to a route, project a waypoint from it, save it as
a waypoint, or view the sun and moon phase from it.
On-screen buttons at the bottom of the page allow you to
Goto the map item, display it on the map or to select ‘OK’
and return to the Map Page.
When using the panning arrow, pressing the FIND
button will display items with the panning arrow (map
pointer) location used as a reference point for nearest
items instead of your current location. Press the PAGE
button to return to the Main Map Page.
Step-by-Step Instructions
Map Item Information
18
To find details about or Goto a map item:
1. Use the CLICK STICK to move the panning arrow to
the map item that you want to learn more about.
2. When the item’s name is highlighted, press in and
release the CLICK STICK to display the Information
Page for that item.
3. Use the CLICK STICK to highlight and press the
‘Goto’ button on the page to navigate to the item.
Reference
Stop Navigation
The ‘Stop Navigation’ option allows you to quit navigation of a Goto, Route or Track in progress.
Map Page
Options
To stop navigation:
1. Select ‘Stop Navigation’ and then press in on the
CLICK STICK.
When there is no active navigation, the ‘Stop Navigation’ option will appear “grayed out” and is non-functional.
.
Hide Navigation Status/Show Navigation Status
‘Stop Navigation’ Option
The ‘Hide Nav Status/Show Nav Status’ option allows
you to view GPS navigation data in a window at the top
of the page that lists the status of satellite tracking and
accuracy of GPS positioning. When hidden, more map
area is displayed.
To hide or show Nav Status:
1. Select ‘Hide’ or ‘Show’ from the option list and then press
in on the CLICK STICK.
Hide Data Fields/Show Data Fields
The ‘Hide Data Fields/Show Data Fields’ option allows
you to view two programmable data fields. When hidden,
more map area is displayed.
Map Page with Nav Status
and Data Fields Hidden.
To hide or show Data Fields:
1. Select ‘Hide’ or ‘Show’ from the option list and then press
in on the CLICK STICK.
Data Field Step-by-Step Instructions
To program a data field:
1. Use the CLICK STICK to highlight the data field and
then press it in to display the options menu.
2. Highlight the desired option and then press in on the
CLICK STICK to place it in the data field.
Map Data Fields
with Options Menu
19
Reference
Data Fields
Data Fields - Overview
Two optional data fields support the Map Page and can
be programmed to display the following options:
Status Field, shows satellite
tracking and accuracy.
(Non-programmable)
Two programmable
data fields.
Programmable Data Field
with list of options.
20
Bearing - The direction from your current location to
a destination.
Course - The direction from your starting location to
a destination.
Off Course - The distance left or right you are from
the original course (path of travel).
To Course - The compass direction you must go in
order to get back to the original course.
Current Destination - The next waypoint on your route.
Current Distance - The remaining distance to
your next waypoint.
Current ETA - The estimated time of day you will
arrive at your next waypoint.
Current ETE - The estimated time needed to arrive at
the next waypoint on your route.
Elevation - The altitude above sea level.
Final Destination - The last waypoint on your route.
Final Distance - The remaining distance to your final
destination.
Final ETA - The estimated time of day you will reach
your final destination.
Final ETE - The estimated time needed to reach your
final destination.
Heading - The direction in which you are moving.
Pointer - Indicates the direction to the next destination.
Speed - Your rate of travel can be displayed in miles
per hour, kilometers per hour, or nautical miles per hour.
Sunrise - The time at which the sun rises on this day.
Sunset - The time at which the sun sets on this day.
Time of Day - The time for the selected time zone.
Trip Odometer - The accumulated distance traveled.
Turn - The angle difference (in degrees) between
the bearing to your destination and your current line
of travel. ‘L’ means turn Left. ‘R’ means turn Right.
Velocity Made Good - The speed at which you are
closing on a destination along a desired course.
Vertical Speed - Your rate of altitude gain/loss over time.
Reference
Setup Map - Overview
The ‘Setup Map’ option displays the Map Setup Pages.
These pages determine how map features are displayed
allowing you to tailor the map to your needs.
Map Page
Setup Options
The Map Page Setup Options
The Map Setup Page consists of five sub pages each
accessed by an on-screen button. Each page provides a list
of options for the features listed.
Scale options are: ‘Off’, ‘Auto’, or 20 feet through 500
miles (5m through 800km). Text Sizes are: ‘None’, ‘Small’,
‘Medium’, or ‘Large’. The ‘Auto Zoom’ option automatically scales the map to display both your current location
and the next point you are navigating to. ‘Zoom’ specifies
the map scale at which an item will be displayed. When
‘Auto’ is selected, the maximum scale will be determined
by the ‘Detail’ setting. Selecting ‘Lock On Road’ will place
the ‘Position Icon’ on the nearest road to compensate for
mapping and GPS accuracy variations.
Page - Orientation: ‘Track Up’ or ‘North Up’.
Auto Zoom; On or Off.
Detail: Most, More, Normal, Less, and Least.
Lock on Road: On or Off.
Tracks - Saved Tracks: Scale options.
Track Log: Scale options.
Goto Line: Bearing or Course.
Map Features - Points of Interest: Scale options.
Waypoints: Scale options.
Street Label: Scale options.
Land Cover: Scale options.
Text - Points of Interest: Text sizes.
Waypoints: Text sizes.
Street Label: Text sizes.
Land Cover: Text sizes.
Transferred MapSource Map Data - Show or Do
Not Show: Check Boxes activate or deactivate.
Scale options indicate the point at which Tracks,
Tracks Logs, Map Features, or Text Boxes for Map Features
will appear, allowing you to remove map clutter and define
map features as desired.
Page Setup
Tracks Setup
Map Features Setup
Text Setup
Map Data
21
Reference
Map Page
Setup Options
Map Page
Setup
Feature Options
Zooming
In and Out
on the Map
Step-by-Step Instructions
To use Setup Map options:
1. Select ‘Setup Map’ from the Options Menu and then press
in on the CLICK STICK to display the Map Setup Page.
2. Highlight the desired sub-page button to display the
features list for that sub-page.
3. Highlight a feature on the list and press in on the
CLICK STICK to display the options list for that feature.
4. Use the CLICK STICK to highlight the desired option
and then press it in to activate.
5. Press the PAGE button or the on-screen ‘X’ button to
return to the Map Page.
Zooming In and Out - Overview
Use the ZOOM IN and OUT buttons to adjust the map
scale, which is displayed at the bottom of the map.
The map scale is shown in the lower left hand side
of the map display area. The scale is shown in the unit of
measure selected from the ‘Units’ field of the Unit Setup
Page (not to be confused with the Map Setup Page).
It is possible to zoom in so far that the resolution of
the map data is exceeded and the appearance of the map
will no longer be accurate. When this occurs, the word,
“overzoom” will appear just below the map scale.
Zoom In
When using MapSource map data, the word “mapsource” will appear below the map scale whenever you
zoom in to view more detailed map features.
You can control the display of map details at specific
map scales by using the Map Setup. Using the Setup
options allows you to create clearer, “less cluttered”, maps
as you desire. Selecting ‘Autozoom’ adjusts the scale to
show both your current location and next point you’re
navigating to.
Zoom Out
Map Scales
and Descriptions
22
Step-by-Step Instructions
To change the map scale:
1. Press the IN Zoom button to select a scale that
shows more detail and a smaller map area.
2. Press the OUT Zoom button to select a scale that displays
a larger map area, but with less detail.
Reference
Navigation Page - Overview
The Navigation Page provides active guidance with a
rotating compass ring that shows your course over ground
(track) while you’re moving and a bearing pointer to
indicate the current direction to your destination (bearing) relative to the course over ground.
The Compass Ring and Bearing Pointer work independently of the direction of your movement and the
direction to your destination. For example: if the arrow
is pointing straight up, you are going directly to your
destination. If it points any direction other than up, turn
toward the arrow until it points up and then continue
in that direction. If you are using the ‘Course Pointer’
option instead and you drift away from the line of travel
to your destination the Course Deviation Indicator (CDI),
provides graphic indication of drift (right or left) and
displays the distance off course. The compass ring is
accurate only when you are moving.
The Navigation Page also displays a ‘Waypoint’ field
above the compass or highway with the name of the next
waypoint on your route or of your final destination. The map
coordinates for that item as shown just below the name.
The Navigation
Page
Navigation Page
with Bearing Pointer
Active
An on-screen button at the top of the page displays the
Options Menu for this page. Options include: ‘Stop
Navigation’, ‘Bearing Pointer’, ‘Course Pointer’, ‘Big Numbers’, and ‘Restore Defaults’. ‘Big Numbers’ converts information in the data fields to display in a large text format
while reducing the size of the compass ring.
At the bottom of the page are two data fields that are user
programmable with a choice of different data options:
Bearing
Course
Off Course
To Course
Current Destination
Current Distance
Current ETA
Current ETE
Elevation
Final Destination
Final Distance
(Definitions on page 20)
Final ETA
Final ETE
Heading
Speed
Sunrise
Sunset
Time of Day
Trip Odometer
Turn
Velocity Made Good
Vertical Speed
Navigation Page with
Course Pointer and
Course Deviation Indicator
(CDI) Scale active.
Use the ZOOM buttons to
adjust the CDI scale
setting.
23
Reference
The Navigation
Page
Navigation Page
Options Menu
Step-by-Step Instructions
Using options to Setup the Navigation Page:
1. With the Navigation Page displayed, use the CLICK
STICK to highlight the Options Menu button at the
top of the page. Then press it in to display the menu.
2. Observe the Options Menu: If you are currently navigating
on a Goto, Track, or Route, the ‘Stop Navigation’ option
will be active, otherwise it will be “grayed out”.
The next option on the list will be ‘Bearing Pointer’,
which is displayed on the compass ring.
The next option on the list will be ‘Big Numbers’
which displays information in two data fields in
large sized numbers above and below the compass while
displaying the compass in a smaller scale. The last option
on the list is ‘Restore Defaults’.
3. Use the CLICK STICK to highlight your selection
and then press in to activate.
To change data fields:
1. Use the CLICK STICK to highlight the desired data
field and then press it in to display the list of data
options.
2. Select the desired option from the list and press in on
the CLICK STICK.
3. You can reset the data fields at any time to change the
type of data viewed while navigating.
Navigation Page
Data Fields
Options Menu
(The slider at the side
of the menu indicates a
multi-page list of options.)
24
Reference
Trip Computer Page - Overview
The Trip Computer provides a variety of data fields
with read-outs of current information as you travel.
Eight fields display navigation information and are user
programmable. The default settings for these fields are
shown in the illustration.
Here is the list of data field options:
Current Destination Speed
Current Distance
Maximum Speed
Current ETA
Moving Avg. Speed
Current ETE
Overall Avg. Speed
Elevation
Odometer
Final Destination
Trip Odometer
Final Distance
Trip Time - Moving
Final ETA
Trip Time - Stopped
Final ETE
Trip Time - Total
Heading
Time of Day
Pointer
(Definitions on page 20.)
Trip Computer
Page
Trip Computer Page
The Option Menu for the page provides the following options: Reset, Big Numbers, and Restore Defaults.
Step-by-Step Instructions
To program a data field:
1. Use the CLICK STICK to highlight the desired data field
and then press it in to open the data field options menu.
2. Use the CLICK STICK to move Up or Down the menu to
highlight a desired data option.
3. Press In on the CLICK STICK to select the option and
place it in the data field.
Data Field Options Menu
To access the page Options Menu:
1. Use the CLICK STICK to highlight the Options Menu onscreen button and press it in to display the options menu.
2. Highlight the desired option and then press in on the
CLICK STICK to activate.
3. To activate individual ‘Reset’ options, highlight the item
on the list and then press in on the CLICK STICK to
place or remove the check mark.
Use care when choosing the ‘Delete’ options,
I asNOTE:
all Tracks, Waypoints, and Routes can be
permanently deleted when resetting the Trip Computer.
Reset Options Menu
Useful when starting a new
trip to clear old data.
25
Reference
The Main Menu
Using the Main Menu
The Main Menu provides access to additional eTrex
Legend feature pages. The pages listed below provide
enhancements to eTrex Legend operation.
Press the PAGE button repeatedly to cycle to the Main
Menu...or select it from the page list at the top of each
main page.
Mark Waypoint Page - Allows you to mark and store
a waypoint for your current location or a map pointer
location.
Main Menu with
Feature Icons
and Power, Date/Time,
and
Backlight Status Window
Find Menu - Allows you to locate a point to
Goto, or to use as part of a Route; Waypoints, Favorite
Locations, Cities, Interstate Exits, Points of Interest,
Addresses, and Intersections.
Route Page - Allows you to create and store routes
for repeated use.
Tracks Page - Provides access to the track log and
saved tracks.
Setup Page - Allows tailoring of items such as
time format, units of measure, display backlighting
timeout and contrast adjustment, interface Setups,
heading selection and system software information.
Accessories Page - Allows you to access Sun and
Moon data, a Calendar, and Hunting and Fishing data.
Power, Date/Time, and
Backlight Status Window
26
Information about the status of backlighting, time and
date, and unit power are displayed in the window at the
bottom of the Main Menu Page.
The battery icon will display the approximate amount
of reserve power available. When the unit is powered by
a cigarette lighter adapter, a power plug icon will replace
the battery icon. The date and time are displayed in the
center of the window and when backlighting is active the
light bulb to the right will appear illuminated.
Reference
The Mark Waypoint Page - Overview
The Mark Waypoint Page allows you to mark and
record your current location as a waypoint and appears
with a graphic name block (man with a flag) that displays
the assigned number for that waypoint and a waypoint
symbol.
Marking Your
Location
Step-by-Step Instructions
To mark your current location as a waypoint:
1. Press in and hold the CLICK STICK until the Mark
Waypoint Page appears. You can also access this page
by highlighting the Mark Icon on the Main Menu Page
and then pressing in on the CLICK STICK. The waypoint
will automatically be assigned a 3-digit number.
2. To change the name of the waypoint, use the CLICK
STICK to highlight the waypoint name field.
3. To assign an identifying symbol to a waypoint, use
the CLICK STICK to highlight the symbol block just
above the waypoint name.
4. To save the waypoint, highlight ‘OK’ and press in on
the CLICK STICK.
5. If you do not want to save it as a new waypoint, press the
PAGE button before pressing any other button to cancel.
To create a waypoint using the map panning arrow:
1. With the Pan Map feature active, move the panning
arrow (map pointer) to the map item you want and
highlight it.
2. Press in and release the CLICK STICK to display the item
Information Page.
3. With the Information Page displayed highlight the options
menu button at the top of the page and then press the
CLICK STICK in to open the menu.
4. Highlight the ‘Save As Waypoint’ option and press the
CLICK STICK in to save the map item as a waypoint.
Mark Waypoint Page
Map Symbol List
Creating a
Waypoint
Marking a Waypoint with
the Panning Arrow
27
Reference
Creating a
Waypoint
To create a waypoint using the panning
arrow when a map item is not highlighted:
1. With the Pan Map feature active, move the panning arrow
(map pointer) on the map to the location you want to
mark and then, press the CLICK STICK in and release.
2. The Mark Waypoint Page will appear, automatically
assigning a number to the waypoint.
Be certain to press and release the CLICK STICK for
this operation. Pressing and holding the CLICK STICK
will mark a waypoint for your current location. See
“Marking Your Location” on page 27.
Marking a Waypoint on
the map without
highlighting a map item.
Creating a
Waypoint by
manually
entering its
coordinates.
Moving a
Waypoint
28
Moving a Waypoint
To create a waypoint by manually entering its coordinates (lat/lon):
1. Press in and hold the CLICK STICK to access the Mark
Waypoint Page.
2. Highlight the Location Field on the Mark Waypoint Page
and enter the new coordinates using the numerical keyboard. Highlight and press ‘OK’ when finished.
3. You may also change the waypoint name and/or symbol.
To move a waypoint by dragging it on the map:
1. Use the Find Menu to display the Waypoint Page for the
waypoint you want to move. Refer to page 30 for more
information on using the Find Menu.
2. Highlight and press the ‘Map’ on-screen button to display the map for the waypoint.
3. With the waypoint highlighted by the panning arrow,
press in and release the CLICK STICK. The word
“Move” will appear beneath the panning arrow.
4. Use the panning arrow to drag the waypoint to the new
location and then press in on the CLICK STICK to place
it there.
5. Press the PAGE button before pressing the CLICK
STICK to cancel moving of the waypoint and return to
the Main Pages.
Reference
Projecting a Waypoint
Projecting a waypoint from any map item (another
waypoint, etc.) allows you to establish a new waypoint
using a bearing and distance projected from that map item.
Projecting
a Waypoint
To project a waypoint:
1. Select a map item from the Find Menu. (See page 30)
2. Highlight the Option Menu on-screen button at
the top of the Information Page and press in on
the CLICK STICK to display the Project Waypoint Page.
3. Highlight the Distance field and press in on the CLICK STICK
to display the numerical keyboard for entering the distance.
4. Enter the desired distance and then the bearing to the
projected waypoint in the appropriate fields and then
select ‘OK’ and press in on the CLICK STICK to complete.
Editing a Waypoint
A waypoint can be edited to change the map symbol,
name, coordinates, or elevation. It can also be deleted.
To edit a waypoint:
1. Use the Find Menu to display the desired waypoint.
2. Make changes as desired to the waypoint map symbol,
name, location coordinates, and elevation fields. Highlight
the desired field and press in on the CLICK STICK to
display the keyboard. Highlight the desired characters on
the keyboard to enter new data and then select ‘OK’ and
press In to close the keyboard.
3. Highlight the ‘OK’ button the press in on the CLICK
STICK to save the changes.
Enter Distance and
Bearing to project
Editing
Waypoints
To delete a waypoint:
1. Use the Find feature to display the desired waypoint.
2. Highlight ‘Delete’ and press in on the CLICK STICK.
To save any Map Item or Find Menu Item as a
waypoint:
1. Access the Information Page for the desired item (highlighted from the map or selected from the Find Menu).
2. Open the Options Menu at the top of the page, select
‘Save As Waypoint’ and press in on the CLICK STICK to
save the item to the Waypoints List.
Use the keyboard to edit
the name
Saving as a
Waypoint
29
Reference
The Find Menu
The Find Menu - Overview
The Find Menu allows you to find stored locations
(waypoints) and map items (cities, exits, etc.). They can be
found by name or by those nearest to your current location
(Position Icon). If you are using MapSource MetroGuide
data, the list of find locations will be expanded to include
categories for Points of Interest, Street Addresses and Intersections.
Press and release the FIND button to access the Find Menu.
Find Page using your
current location as a point
of reference
The Find Menu allows you to locate and travel to:
Waypoints - Marked and saved locations on the
map used as a destination or a point on the way
(waypoints) to a destination. Refer to page 27 to mark
or create a waypoint.
Favorites - A list of familiar and often used waypoints.
‘Nearest’ or ‘By Name’
Prompt
Cities - A list of cities in the basemap.
Interstate Exits - A list of all Exits on the nearest
Interstate Highway, categorized by “All Types”, “Services”, “Rest Areas”, and “Other” (weight stations, etc.).
‘Near Map Pointer’ or ‘By
Name’ Prompt.
Displayed when using the
Map Pointer.
Points of Interest - A list of restaurants, museums,
hospitals, etc.
Addresses - A page with data entry fields for address
number, street name, city and postal code, used to
define an address.
Intersections - A page with data entry fields for two
streets, a city, and postal code. Used to define an intersection.
For some categories, there are two methods of
listing. The “By Name” list contains every item in the map
database for the selected category, while the “Nearest” list
contains only those items that are near to your Current
Location or near to the Map Pointer. Categories listed by
either method will display a choose prompt.
Item Information Page
30
These pages are structured with a set of sub-menus
and location information pages that guide you through
the process of finding locations. Use them to construct
a Route, establish a direct line of travel (Goto), or when
gathering information.
Reference
Finding a Waypoint - Overview
The Find Menu
Waypoints that you have created and stored in the
eTrex Legend can be found by selecting the ‘Waypoint’
option from the Find Menu. You can find a waypoint
from the list of waypoints using the ‘By Name’ or ‘Nearest’
options explained on the previous page. When selected
from the list the waypoint will be displayed on the Waypoint Information Page.
The Waypoint Information Page displays the waypoint
name or number, a map symbol, the location in lat/lon,
elevation, distance, bearing, and three on-screen buttons
for ‘Goto’, ‘Map’, and ‘OK’ functions.
Step-by-Step Instructions
To find a waypoint:
1. Use the CLICK STICK to select the Waypoint option
from the Find List and then press it in to display a
prompt to select ‘By Name’ or ‘Nearest’. Select and press
in on the CLICK STICK to display the Waypoints List.
2. Use the CLICK STICK to select the desired waypoint
from the list and then press it in to display the
Information Page for that waypoint.
3. With the Information Page displayed, you can
select ‘Goto’ to create a direct line of travel
to the waypoint. Select ‘Map’ to view the waypoint location on the map or select ‘OK’ to close
the page.
4. Use the page option menu to add the waypoints to
the ‘Favorites’ list, add it to an existing route, project a
new waypoint from this location, view sun and moon,
and best fishing and hunting time information for this
waypoint.
Waypoint Find List
Waypoint Information
Page
Finding a Favorite - Overview
Favorites are map items and waypoints that have been
designated as those you would like to give a special
status, as they are frequently used or have other special
significance. The process for finding favorite waypoints
from the ‘Favorites’ list is the same as finding a regular
waypoint, but without ‘By Name’ or ‘Nearest’ options.
Favorites Category
31
Reference
The Find Menu
Favorites List
Step-by-Step Instructions
To find a ‘Favorite’:
1. Use the CLICK STICK to select the ‘Favorites’
option from the Find List and then press it in to
display the list. There is no ‘By Name’ or ‘Nearest’
option.
2. Use the CLICK STICK to select the desired Favorite
from the list and then press it in to display the
Information Page for that item.
3. With the Information Page displayed, you can select
‘Goto” to create a direct line of travel to the item. Select
‘Map’ to view the waypoint location or select ‘OK’.
4. Use the page option menu to add the item to an existing
route, project a new waypoint from this location, or view
sun and moon position data for this time and date.
Finding a City - Overview
Cities can be found by selecting the ‘Cities’ option of the
Find Menu, selecting the city from the list of ‘Nearest’ or
‘By Name’, and then displaying the City Information Page.
Find List for Nearest Cities
32
City Information
Page
The City Information Page for the selected city displays
the city name, the size by population, and distance from
you location. You can view it on the map or create a Goto
direct route to the city from your current location, or from
a location defined by the Panning Arrow (Map Pointer). You
can also save it as a waypoint or add it to an existing route.
Step-by-Step Instructions
To find a city:
1. Use the CLICK STICK to select the ‘Cities’ option, then
press it in to display the list. You will be prompted to
select ‘By Name’ or ‘Nearest’. Selecting ‘By Name’, displays the keyboard to help eliminate scrolling through the
list of cities.
2. If you are using ‘By Name’, begin spelling the name of
the city by using the keyboard. When you have entered
enough characters to define the name, a match list will
be displayed. Use the CLICK STICK to select the desired
City from the list and then press it in to display the
Information Page for that city.
3. With the Information Page displayed, you can select
‘Goto’ , ‘Map’, ‘OK’ buttons, or the ‘Save As’ menu option.
Reference
Finding an Exit - Overview
You can use the Find Exit option to locate a nearby
exit on an interstate highway. Exits are listed only by
‘Nearest’. Exit information pages provide a variety of
information about services near each exit, including rest
stops, lodging, restaurants, service stations, etc. Some
services (i.e. service stations) on this page can be selected
and a separate information page will display with specific
information concerning what types of fuel, mechanical or
food services are available.
The Find Menu
Exit
Types List
Step-by-Step Instructions
To find an exit:
1. Press the FIND button to display the Find Menu.
2. Use the CLICK STICK to highlight ‘Exits’ and then
press it in to display the Exit List.
3. Observe the ‘pop-up’ type options menu and then
highlight and select an exit type by pressing in on the
CLICK STICK.
4. A list of exits nearest to you will be displayed. The title
box indicates the interstate highway which is served by
the exits. Two fields at the bottom of the page indicate
distance and bearing to the exit currently highlighted.
5. Scroll through the list to highlight the desired exit.
6. Press in on the CLICK STICK to display the
Information Page for that exit. This page contains the exit
description at the top of the page with a list of available
services near that exit, displayed below. Distance and
bearing fields are also displayed.
7. Use the CLICK STICK to move to the list of services
and highlight a selection from the list.
8. Press in on the CLICK STICK to display the
Information Page for the selected service.
9. The Exit Services Information Page will display the name
of the service, its direction from the exit, and a list of the
services available.
10. At the bottom of these Information Pages are on-screen
buttons for ‘Goto’, ‘Map’, and ‘OK’.
11. Use the options menu at the top of the page to save
the exit as a waypoint, ‘Favorite’, project a waypoint, or
add to an existing route.
Exits List
Exit Information Page
Services Information
33
Reference
The Find Menu
Finding a Point of Interest - Overview
You can use the ‘Find Points of Interest’ option
to locate a nearby restaurant, lodging, landmark, public
building, park, etc. However, you must have first transferred a MapSource MetroGuide map to the unit map database. Otherwise this option, plus Address and Intersection
options will appear gray and will not be functional.
Points of Interest List
Food & Drink Categories
Here is a list of Point of Interest categories:
Food & Drink
Services
Lodging
Transportation
Attractions
Emergency & Govt.
Entertainment
Manmade Places
Shopping
In many instances, these categories are sub-divided
into types, such as in the instance of Food & Drink. When
you select Food and Drink from the list of categories you
are then presented with a list of types which includes ‘All
Types’ and cuisine options like American, Asian, Barbecue,
Chinese and many more. When you select a restaurant that
is part of a national chain (for example: McDonalds) the
name will appear only once. However, when you highlight
it and press in on the CLICK STICK, a list of ‘Nearest’
locations for that name will appear.
Once you have selected an item, press in on the CLICK
STICK to display the Information Page for that item. You
can then use on-screen buttons to: ‘Goto’, view the location
on the ‘Map’, or the option menu to add to a list, route,
or save as a waypoint.
Step-by-Step Instructions
Nearest Fast Food List
34
To find a point of interest:
1. Press the FIND button to display the Find Menu.
2. Use the CLICK STICK to highlight ‘Points of
Interest’. Choose find ‘By Name’ or find ‘Nearest’, then
press it in to display the Points of Interest Categories List.
3. Use the CLICK STICK to select the desired category
and then press it in to display the Types List.
4. Use the CLICK STICK to select the desired type and
then press it in to display the list for that type.
Reference
To find a point of interest: (continued)
5. If you selected ‘By Name’ a keyboard will display, allowing you to enter the characters of the name you want.
When enough characters are entered a list of matches
is displayed. If you selected ‘Nearest’, just scroll through
the list.
6. Use the CLICK STICK to highlight your selection
from the list and then press it in to display the
Information Page for that item.
7. Use the on-screen buttons to ‘Goto’ or view on the ‘Map’,
or the page options menu to add the item to a list, save it
as a waypoint or add the item to an existing route.
The Find Menu
Finding an Address or Intersection - Overview
You can enter a street number, choose a street name
from a list and find an address within the area of map data
coverage. You enter two street names and locate the point
where they intersect. However, you must first be using a
MapSource MetroGuide which provides this type of map
data, otherwise this option will not be available.
Point of Interest Info Page
Step-by-Step Instructions
To locate an address:
1. Press the FIND button to display the Find Menu.
2. Use the CLICK STICK to highlight ‘Address’
and press it in to display the ‘Find Address’ page.
3. Highlight the’ Number’ field and use the keyboard for
entering numbers.
4. Move to the ‘Street’ field using the CLICK STICK.
5. Press in on the CLICK STICK to display the
‘Select Street Name’ list. Find the street by using the
keyboard to enter characters until a list appears.
6. With the desired street highlighted, press in on the
CLICK STICK to place the street name on the Find
Address page. Repeat this process for city and postal
codes, if desired. A window at the bottom of the page
displays a list of matches and the quality of each match.
7. Use the on-screen buttons at the bottom of the page to
‘Goto’, view the item on the ‘Map’, or ‘OK’ to close.
8. Use the Options Menu to: Add To Favorites, Add To
Route, Project a Waypoint, Save as Waypoint, View Sun
and Moon, or Hunt and Fish.
Find Address Page
Entering an Address
35
Reference
The Find Menu
Find Intersection Page
Find Street Keyboard
Entry
Using a Goto
To locate an intersection:
1. Display the Find Menu and use the CLICK STICK to
highlight the ‘Intersection’ category and press it in to
display the ‘Find Intersection’ page.
2. Highlight the first ’Street’ field and then press in on
the CLICK STICK to display the ‘Street‘ list.
3. Enter the name of the street in the name field at the
top of the list using the keyboard data entry method.
Once you have spelled enough of the street name, you
will get a match with several on the list. Press in on the
CLICK STICK to move the highlight to the street list and
then scroll up or down until you find the street name you
want. Press it in to place the name in the field.
4. Repeat the process to select the second street name and
city and postal codes, if desired.
5. A window at the bottom of the page displays a list of
matches and the quality of each match, allowing you to
choose the most likely intersection. If no match is found, it is
likely that no such intersection exists.
6. Highlight the best match and then press in on
the CLICK STICK to display the Information Page for
the intersection. Use the on-screen buttons at the bottom
of the page to ‘Goto’, view the item on the ‘Map’, or ‘OK ‘
to close.
7. Use the Options Menu to:
Add To Favorites, Add To
Route, Project a Waypoint,
Save as Waypoint, View
Sun and Moon positions, or
Hunt and Fish for viewing
Information Page Options
best hunting and fishing
times.
Using a Goto to Navigate to a Destination
The Goto function allows you to create a direct route
to a destination, (waypoint, map item, address, etc.) Use
the Goto button at the bottom of the Information Page to
travel to a map item using the Map and Navigation Pages.
36
Information Page
‘Goto’ Button
To activate a Goto:
1. Access the Information Page for any desired destination
and use the CLICK STICK to highlight the Goto button.
2. Press in on the CLICK STICK to start navigation.
Reference
Creating and Using a Route - Overview
Routes
Route navigation allows you to create a sequence
of intermediate waypoints which lead you to your final
destination. The eTrex Legend will store 20 routes, each
with up to 50 waypoints. A route can be created and
modified from the Route Page, and waypoints can be
added to a route from the Find Menu. More complex
routes can be created using a PC and MapSource mapping
programs and then transferred to the unit memory. You
can add a waypoint or map item to an existing route at
any time.
Step-by-Step Instructions
To create a route:
1. Access the ‘Routes’ page from the Main Menu. The page
has a ‘New’ button, a list of routes, and the number of
unused routes.
2. Use the CLICK STICK to highlight the ‘New’ button and
press it in to display the route Setup Page.
3. With an empty row (dashed) in the route list highlighted,
press in on the CLICK STICK to display the Find Menu.
4. Use the Find Menu to select a route waypoint from one
of the Find Menu categories and display the Information
Page for selected waypoint, city, exit, point of interest,
etc. Highlight the on-screen ‘OK’ button and press in on
the CLICK STICK to place it on the Routes List.
5. To add more waypoints to the route, repeat the process in
Steps 3 and 4. The route will be named for the first and
last waypoints on the route.
You can add waypoints to the end of an existing route
at any time by using the Find Menu.
To add a Find Menu item to a route:
1. Select an item from the Find Menu and display its
Information Page.
2. Display the page Options Menu and select the ‘Add To
Route’ option to display the Routes List.
3. Highlight and select the route desired and then press in
on the CLICK STICK. A “Waypoint Added Successfully”
message will appear.
The Routes Page with a list
of Routes and the number
of Unused Routes.
A Route with list
of waypoints.
“Add To Route” option
from the Find Menu
Information Pages
37
Reference
Routes
A Route Options Menu
Editing a Route
To remove all waypoints:
1. Select the on-screen page options button from the Route
Page and press the CLICK STICK in to access the options
menu.
2. Highlight the ‘Remove All’ option and then press in
on the CLICK STICK to remove all waypoints from
the list. You will be prompted, “Do you really want to
remove all waypoints from the route?”, select “Yes”.
To reverse the route:
1. Select the on-screen page options button from the
Route Page and press the CLICK STICK in to
access the options menu.
2. Highlight the ‘Reverse Route’ option and then press in
on the CLICK STICK to reverse the order of waypoints in
the list. To change the route back to the original order,
repeat this process.
To copy the route:
1. Select the on-screen page options button from the
Route Page and press the CLICK STICK In to
access the options menu.
2. Highlight the ‘Copy Route’ option and then press in on
the CLICK STICK to copy. The copied route will appear on
the Routes Page. The original route will be named the
same with the copied route followed by a numeral 1. You
may then rename and/or modify the copied route.
Routes List With Two
Copied Routes.
Copied Routes have a
‘1’ Suffix.
Delete Route Prompt
38
To delete the route:
1. Select the on-screen page options button from the
Route Page and press the CLICK STICK In to
access the options menu.
2. Select ’Delete’ and then press in on the CLICK
STICK. You will be prompted, “Do you really want to
delete route?”. Select “Yes”.
To restore default settings for the route:
1. Select the on-screen page options button from the
Route Page and press the CLICK STICK in to
access the options menu.
2. Select ’Restore Defaults’ and then press in on the
CLICK STICK to restore factory settings.
Reference
Editing a Route (Continued)
Routes
To review a waypoint:
1. Select the waypoint from the Route Waypoints List
and press the CLICK STICK in to access the
options menu for the waypoint.
2. Highlight ‘Review’ and then press in on the CLICK
STICK to display the Information Page for the waypoint.
3. Highlight the on-screen ‘OK’ button and then press in
on the CLICK STICK to return to the Route List.
To insert a new waypoint on the route list:
1. Select the row where you want the new waypoint inserted.
Press the CLICK STICK in to access the options menu.
2. Highlight ‘Insert’ and press in on the CLICK
STICK to display the Find Menu and select a new
waypoint, city, exit, point of interest, etc.
3. With the new waypoint highlighted, press in on
the CLICK STICK to display the Information Page for
the new waypoint and then select the on-screen ‘OK’
button to add it the route.
To remove a waypoint from the route list:
1. Select the waypoint that you want to remove
from the Route Waypoints List and press in on
the CLICK STICK to display the options menu for
the waypoint.
2. Highlight ‘Remove’ and press in on the CLICK
STICK to remove the waypoint from the list.
To change a route waypoint:
1. Select the waypoint that you want to change
from the Route Waypoints List and press in on
the CLICK STICK to display the options menu for
the waypoint.
2. Highlight ‘Change’ and press in on the CLICK
STICK to display the Find Menu or create a new
waypoint and add it to the Waypoints list.
3. Select a new waypoint, access its Information Page and
press the on-screen ‘OK’ button to replace the old route
waypoint.
Route Page with
Waypoint List
Route Waypoint
Options Menu
Using the Find Menu to
change a Route Waypoint
39
Reference
Routes
To move a route waypoint:
1. Select the waypoint from the Route Waypoints List
and press the CLICK STICK in to access the
options menu for the waypoint.
2. Highlight the ‘Move’ option and press in on the
CLICK STICK to display the waypoint on the map.
3. Use the CLICK STICK to move the panning arrow
to the waypoint and then press it in to activate
the ‘Move’ feature (a ‘Move’ note will appear by the
waypoint).
4. Use the CLICK STICK to drag the waypoint to
the new location, then press it in to place it.
Adding or Editing a Waypoint from the Route Map Page
Moving a Route Waypoint
by clicking and dragging.
Map Page Route Options
Adding a Route Waypoint
to an end point on the
Route Map Page
40
You can use the panning arrow with the Route Map
Page displayed to add or edit route waypoints.
To add a route waypoint at either end of a route:
1. Select the Route from the Routes List and press the
CLICK STICK in to display the Route Page.
2. Highlight the on-screen ‘Map’ button at the bottom of
the page and press in on the CLICK STICK to
display the Route Map Page.
3. Use the CLICK STICK to move the panning arrow
to either end of the displayed route until the end waypoint is highlighted. Then press it in to display the
map options menu and select ‘Add Turns’. This option
appears only when highlighting the end point of a route.
4. Move the panning arrow to a map item or location where
you would like to extend the route and press in on
the CLICK STICK to display the Information Page
for the new waypoint. Press the on-screen ‘OK’ button to
return to the map page and then press it in again to
place the new waypoint.
To add a route waypoint within a route:
1. Follow steps 1 and 2 in the previous instruction.
2. Use the CLICK STICK to move the panning arrow to a
route line. When the arrow touches the line, the line will
become thin. Press in on the CLICK STICK to display the
word ‘ADD’ next to the line.
Reference
3. Next, drag the line to a map item or other location
where you want to establish a new waypoint and then
press in on the CLICK STICK to place the new waypoint.
A waypoint information page will display. Press the onscreen ‘OK’ button to save the new waypoint, then press
it again to return to the Route Map.
To review or remove a route waypoint:
1. Select the Route from the Routes List and press the
CLICK STICK in to display the Route Page.
2. Use the CLICK STICK to highlight the desired route
and press in to display the Route Page for that route.
3. Use the CLICK STICK to move the map panning
arrow to the waypoint you want to review and press in to
pop-up the options menu. Select ‘Review’ or ‘Remove’
and press it in again to either display the Information Page
for that waypoint or remove it from the route.
Routes
Adding a new waypoint
within a Route
To view the next waypoint in the route:
1. Follow Steps 1 and 2 above.
2. Place the map panning arrow on the waypoint you are
currently viewing and press in to display the options
menu. Select ‘Next’ and press in again to view the
next waypoint which will be centered on the page.
Navigating a Route
A Route can be navigated using the Map Page or the
Navigation Page. The Map Page displays your movement,
the route line, and waypoints on the route. The Navigation
Page provides compass direction and a bearing pointer.
To navigate a route:
1. Select a route from the Routes List and then press in
on the CLICK STICK to display the Route Page.
2. Highlight the on-screen ‘Navigate’ button at the bottom
of the page and then press in on the CLICK STICK to
begin navigating the route.
3. Observe that you have moved to the Navigation Page.
4. Move to the Map Page and observe the route displayed on
the map and the position icon indicating your current location.
5. Begin moving and observe directional information on the
Navigation Page and your progress on the Map Page.
6. To stop navigation use the ‘Stop Navigation’ option on either
page or the ‘Stop’ button on the Route Page.
Navigation Page with
Bearing Pointer
Navigating a Route on the
Map Page
41
Reference
Routes
Data Fields for the Route Page
When navigating a Route, the data displayed in the
data fields on Route Page may be customized to provide
useful navigation information that is specifically related to
route navigation. These data options appear only on the
Route Page.
Options for this type of navigation are:
Data Field Options Menu
Distance to Point vs Leg
Distance. To view Leg
information, highlight the
end waypoint on a leg.
42
Distance to Point - The distance from your current location to a route waypoint.
Leg Course - The line of travel between two route
waypoints.
Leg Distance - The distance between two route
waypoints.
Leg Time - The time required to travel from a route
waypoint to the next.
ETA To Point - Estimated Time of Arrival at a route
waypoint (in sequence).
ETE To Point - Estimated Time Enroute to a route
waypoint.
Sunrise At Point - Time of sunrise at a route waypoint.
Sunset At Point - Time of sunset at a route waypoint.
Pointer - Direction pointer to a route waypoint.
To select data field options:
1. Use the CLICK STICK to highlight a data
field on the Route Page and then press it in
to display the Data Field Options Menu.
2. Use the CLICK STICK to highlight the desired
option and then press in to enter the option in the
data field.
Reference
Using Track Logs - Overview
Tracks Page
The eTrex Legend draws an electronic bread crumb
trail on the Map Page as you travel along. This bread
crumb trail is the ‘Track Log’. The Track Log contains
information about points along its path, including time
and position. The eTrex Legend uses this information to
allow you to navigate using the saved track.
The ‘TracBack’ feature allows you to return along a
traveled path without marking any waypoints. When you
are ready to return to where you started, the eTrex Legend
will take you back by following the ‘Track Log’ that you
left behind. You can save a total of ten tracks in the unit
memory. The Track Log starts recording as soon as the
unit gets a satellite location fix with the Track Log feature
turned on.
Tracks Page
If you want to keep a record of a certain track
log or use the ‘TracBack’ feature, it is recommended that
you clear the Track Log before you start traveling. The
percentage of memory used by the current track log is
displayed in a window at the top of the page. After the
Track Log is ‘Cleared’, it will show zero percent. When
the display shows 99%, the most recent track points will
start overwriting the least recent. To avoid losing track
points you want, save the Track Log before it reaches the
99% mark.
The Saved Track Page displays the track and it can also
be displayed on the Main Map Page as you navigate.
The ‘TracBack’ feature allows you to retrace your track
in both directions. Tracks are marked BEGIN and END.
You can set the track recording interval to Distance,
Time, or Automatic. You can set the Track display resolution to High, Medium, Low, and Lowest. You can also use
the options menu to delete all saved tracks.
Track on Main Map Page
For effective use of the
“TracBack’ feature, clear
the Track Log before starting a new trip or after
saving the Track Log.
Rename saved Track Logs
to help identify them later.
43
Reference
Tracks Page
Saved Track Page
Save Track Options
TracBack Options
Track Log Setup Menu
Record
Method
Options
If you choose Auto-record, you
can set the recording interval
from More to Least Often. You
can set recording intervals for
Time or Distance as desired.
44
Step-by-Step Instructions
To save and use a Track Log:
1. Access the ‘Tracks’ page from the Main Menu. The page
has On/Off buttons, a list of tracks, and the number of
unused tracks.
2. You can press in on the on-screen ‘Off’ button to pause
track logging. When track logging is active the ‘On’
button will appear to be recessed.
3. Highlight the on-screen ‘Save’ button and then press
in on the CLICK STICK to display the track log
‘Save Back Through’ list.
4. Use the CLICK STICK to select the time and date that
you would like to save the track through.
5. Press in on the CLICK STICK to save the track log and
display the Track Page.
6. The Track Page shows the track name (which can be
renamed using the keyboard for data entry), the total
distance of the track, the number of points along the
track, a ‘Show on Map’ option with check box, and onscreen buttons for ‘Map’, ‘OK’, and ‘Tracback’.
7. To enable the Tracback feature, highlight the ‘Tracback’
button and then press in on the CLICK STICK.
This will display the Tracback Menu with two
options, ‘To Beginning’ and ‘To End’. Highlight
the desired option and then press in on the CLICK
STICK to enable. Access the Map Page or the
Navigation Page to navigate the Track.
To use Track Log Setup options:
1. Highlight the Tracks Page Options Menu button at
the top of the page and press in on the CLICK
STICK to display the menu.
2. Highlight the ‘Tracks Log Setup’ option and then press
in on the CLICK STICK to display the Setup Page.
You can check the ‘Wrap When Full’ option by highlighting it and then pressing in on the CLICK STICK.
You can highlight the ‘Record Method’ and ‘Interval’
fields and press in on the CLICK STICK to display their
options. ‘Interval’ options will change to accommodate the
‘Record Method’ choices.
Reference
The Setup Pages - Overview
Setup Pages
The Setup Pages allow you to customize your
eTrex Legend to meet your personal preferences. You
can choose from time settings, units of measure, display
backlighting and contrast settings, heading measurement,
interface options, and system operating mode.
By highlighting the icons on the Setup Menu and then
pressing in on the CLICK STICK, you can display the
Setup Page for each of the menu items.
Time Page - Overview
You can set the time to match your location or for a
projected location anywhere in the world.
Time Format - Allows you to choose from
12 or 24 hour time format. When you select the
12 hour time format, the clock will read like a
standard clock with 12 hour AM and PM cycles. The
24 hour option sets the clock to display a 24 hour
cycle (Military Time).
Setup Menu
Time Zone - Can be set to one of the eight US
Time Zones, or 24 International Time Zones (nearest
city or geographical region) When selecting ‘Other’
you can enter the UTC Time Offset for any other
time zone. Refer to the instructions for setting the UTC
Time Offset on page 54 of the Appendices.
Daylight Savings Time - Can be turned On or Off
or set to Automatic.
Step-by-Step Instructions
To set the time:
1. Use the PAGE button to access the Main Menu.
2. Use the CLICK STICK to highlight the Setup Icon and
then press it in to display the Setup Menu.
3. Use the CLICK STICK to highlight the Time Icon and then
press it in to display the Time Page.
4. Use the CLICK STICK to highlight the ‘Time Zone’ field
then press it in to display the list of time zone options.
5. Highlight a time zone from the list of 8 U.S. time zones
or 24 international time zones (defined by nearest city or
geographically) and then press in on the CLICK STICK.
6. Observe the correct time displayed at the bottom of the page.
Time Setup Page
Time Format
Options
Daylight
Savings
Options
Time Zone Options
45
Reference
Setup Pages
Units Page - Overview
The Units features are best used by individuals with
a working knowledge of map grids and datums. To learn
more about these subjects, visit the National Imagery
and Mapping Agency at http://www.nima.mil or inquire
at your library.
Position Format - Allows you to choose from
different grid formats. The default position format,
‘hdddomm.mmm’ displays the latitude and longitude
in degrees and minutes and is most commonly used.
Units Page
Position Format
Options Menu
Map Datum - Offers a selection of nearly all map
datums in common use. Every map is based on a
map datum (a reference model of the earth’s shape)
and is usually listed in the title block of the map. If
you are comparing GPS coordinates to a paper map,
chart, or other reference, the map datum in this field
must match the horizontal map datum used to generate the map or other reference. The default datum
is WGS 84 (World Geodetic Survey 1984) and should
only be changed when using maps or charts specifying
a different datum. If a map does specify a datum,
use the options list to find datums applicable to the
region of the map, selecting the one that provides
the best positioning at a known point. You may also
choose the ‘User’ datum for custom designed grids.
Distance/Speed - You can choose from three units of
measure to display your rate of travel.
Elevation/Vertical Speed - You can choose from two
units of measure to record your elevation and rate of
ascent.
Map Datum
Options Menu
Distance/
Speed
Options
46
Elevation/
Vertical
Speed
Options
Step-by-Step Instructions
To select Units Page options:
1. For all fields on this page, highlight the field and
then press in on the CLICK STICK to display the
options menu for the field.
2. Highlight the desired option on the menu and then press
in on the CLICK STICK to place it in the field.
Reference
Display Page - Overview
Setup Pages
You can adjust the amount of time that the backlighting feature stays on before timing out and adjust the
screen contrast for best viewing.
Backlighting Timeout - Allows you to choose from
always On, to delays of 15 seconds, 30 seconds, one,
or two minutes before timing out.
Contrast Adjustment - Can be adjusted from light to
dark using the slider adjacent to the contrast bar.
Step-by-Step Instructions
To set the backlighting timeout:
1. Highlight the Backlight Timeout field and then press
in on the CLICK STICK to display options.
2. Highlight the desired option and then press in on the
CLICK STICK to activate it.
Display Page
Backlight
Timeout
Options
To adjust the contrast:
1. Highlight the contrast slider and then press in on the
CLICK STICK to activate.
2. Move the CLICK STICK Up or Down to move the
contrast slider until the desired contrast has been set.
Heading Page - Overview
You can select from three types of heading displays,
and four types of North References and enter the magnetic variation when selecting a ‘User’ reference.
Display - Allows you to choose from Cardinal Letters,
Degrees or Mils.
North Reference - You can choose from True,
Magnetic, Grid or User options. If ‘User’ is chosen
you must enter the Magnetic Variation using data entry
techniques.
Step-by-Step Instructions
To select Display and North Reference options:
1. Highlight the field and then press in on the CLICK
STICK to display the options.
2. Highlight the option and press in on the CLICK
STICK to activate.
Heading Page
Display
Options
North Reference
Options
47
Reference
Setup Pages
Interface Page - Overview
The Interface Settings Page allows you to choose from
seven different input/output serial data formats, or, none
at all. This feature is used when connecting your eTrex
Legend to external NMEA devices, a DGPS beacon receiver,
a personal computer, etc. For effective use of this feature it
is necessary to have a working knowledge of these applications. Following is a description of each format:
GARMIN Mode
with No Options
GARMIN - The proprietary format used to exchange
waypoint, track, and map data with a PC.
GARMIN DGPS - Allows DGPS input using a
GARMIN beacon receiver and a standard RTCM
SC-104 and DGPS tuning.
NMEA Out - Supports the output of standard NMEA
0183 version 2.3 data.
Text Out - Allows simple ASCII text output of location
and velocity information, without any input capabilities.
RTCM In - Allows DGPS input using a standard
RTCM SC-104 format without any output capabilities.
RTCM In/NMEA Out- Allows DGPS input using a
standard RTCM SC-104 format and supports the
output of standard NMEA 0183 version 2.3 data.
RTCM In/Text Out- Allows DGPS input using a
standard RTCM SC-104 format and simple ASCII text
output of location and velocity information.
None - Provides no interfacing capabilities.
GARMIN Differential
GPS Mode
with Data and Options
Fields
48
If ‘GARMIN DGPS’ or ‘RTCM in/NMEA Out’ format
is selected, additional fields are provided to control a
GARMIN differential beacon receiver (e.g. GBR 21 & GBR
23) directly from your unit. Tuning is automatic with
‘Scan’ or you can enter the beacon frequency and bit rate
when you select ‘User’ from the Beacon list to manually
tune the receiver. Refer to the beacon receiver instructions.
Step-by-Step Instructions
To select a serial data format:
1. Highlight the Serial Data Format field and then press
in on the CLICK STICK to display options.
2. Highlight the desired option and then press in on the
CLICK STICK to activate it.
3. If you selected a format that displays additional fields,
highlight those with options and make your selection
using the CLICK STICK.
Reference
System Page - Overview
Setup Pages
The System Setup Page allows you to select from four
modes of operation ‘Normal’, ‘Battery Saver’, ‘Use With
GPS Off’, and ‘Demo Mode’.
Of the GPS options, the ‘Battery Saver’, ‘Use With
GPS Off’, or ‘Demo Mode’ will significantly save battery
power. The ‘Battery Saver’ mode reduces the rate of satellite signal position updating and the ‘Use With GPS
Off’ option stops satellite signal reception altogether. The
‘Demo Mode’ simulates navigation.
This Page Option Menu also displays the current version
of unit operating software and the Unit i.d. Number. The
path for downloading software updates from the GARMIN
website is (www.garmin.com). Downloading updates requires
use of the GARMIN PC Interface Cable, supplied with this
unit. Instructions are posted at the website.
You can use the Wide Area Augmentation System (WAAS)
capability of the eTrex Legend to produce a more accurate
position fix (3 meters nominal). When enabled (the GPS
mode must be set to ‘Normal’ and interface set to other
than RTCM mode), this feature searches for a WAAS satellite
near your location and then receives data for correcting differentials in the GPS satellite signals. When WAAS has been
enabled, you will see WAAS satellite numbers, beginning at
No. 33 or above, displayed on the Satellite Page. When differential correction data has been received for GPS satellites
(numbers 32 or below), a ‘D’ will appear in the signal bar
beneath the skyview. It is helpful to orient the unit antenna
toward the WAAS satellite shown in the skyview. To learn
more about the WAAS System, its satellite positions and current state of development, access the Federal Aviation Administration website (http.//gps.faa.gov/). Refer to the Trouble
Shooting Guide on page 57 if WAAS access is not obtained.
You can select from a list to change the display language.
The bottom of this page, shows the Amount of Memory
Used, Power Status, Date and Time and Backlighting Status.
System Setup Page in
Normal Mode,
WAAS Enabled, and
English Language
WAAS Enabled.
WAAS Satellite is No. 35
and ‘D’ in Signal Bars for
GPS Satellites
Step-by Step Instructions
To select System Page options:
1. Highlight the field and then press in on the CLICK STICK
to display the options. Then use the CLICK STICK to select.
System Page Options
49
Reference
Accessory Pages
Accessories Menu
The are three accessory pages (features which enhance
the unit operation, but are not essential), sun and moon
position relative to a location, a calendar displayed by
month, and a hunting and fishing best times record.
Highlight the appropriate icon and then press in on the
CLICK STICK to display the desired page.
Sun and Moon - Overview
This feature provides you with a graphic display of both
sun and moon positioning for a certain date, time and location with times for sunrise, sunset, moonrise, and moonset.
Accessory Menu
On-screen buttons at the bottom of this page allow you
to animate the movement of the sun and moon and stop
it at a given date. The first button on the left animates the
overhead display of the sun and moon and you can view
positions for any given date by observing the date field and
stopping movement when the desired date is displayed.
You can also display the different phases of the moon by
pressing the center button and then the far right ‘stop’
button when the desired date appears.
Step-by-Step Instructions
Sun & Moon Page
Location Options List
Overhead Moon Phase Stop
Animation Buttons
50
To set the date and time:
1. For the Date and Current Time, highlight each field
and then press in on the CLICK STICK to begin data
entry of individual characters.
2. To display the current date and time, highlight the page
Options Menu and press in on the CLICK STICK to
display the ‘Use Current Time’ option and then press in on
the CLICK STICK to activate.
To set the location:
1. Highlight the Location field and then press in on the
CLICK STICK to display the ‘New Location’ options list.
2. Highlight the option desired and then press in on
the CLICK STICK to activate. If you choose ‘Current
Location’ the field values displayed on the page will
reflect the view from your current location. If you choose
‘Use Map’, a map page will display. Use the map pointer
to identify the desired location and then press in on
the CLICK STICK. If you choose ‘Use Find Menu’ follow
instructions for using the Find Menu on page 30.
Reference
Calendar - Overview
Accessory Pages
This feature provides you with a monthly calendar with
programmable reference notes dates. You can display one
monthly calendar of days at a time and mark days on each
with reference notes using the data entry keypad. You can
create reference notes for multiple months and for months
years in yet to come. You can record 100 notes with up to
18 characters each.
Step-by-Step Instructions
To set the month and year:
1. For the month, highlight the month and then press in
on the CLICK STICK to begin to enter new month using
the data entry keyboard.
2. For the year, highlight the year and then press in on the
CLICK STICK to begin entering the year using the data
entry keyboard.
Or...
3. Choose ‘Set To Current Date’ from the Options Menu.
To create a reference note for a selected date:
1. Use the CLICK STICK to highlight the day of the
month and then press in to display the options menu
for the date.
2. Highlight and select ‘New Note’ to begin entering text
from the keyboard.
3. Observe the message as it is created in the message block
below the keyboard.
4. To edit or delete a note previously created, highlight
the date and press in on the CLICK STICK. You will be
presented with ‘Edit Note’, ‘Delete Note’, ‘View Sun and
Moon’, or ‘View Hunt and Fish’ options.
Calendar Page
Calendar Page Options
Calendar Date Options
Calendar Page Keyboard
and Message Block
51
Reference
Accessory Pages
Hunt and Fish - Overview
This feature provides you with a listing of best times
for hunting and fishing for a chosen location and date.
Step-by-Step Instructions
To set the date:
1. Highlight the date field and then press in
on the CLICK STICK to begin data entry of
individual characters. To display the current date,
highlight the page Options Menu and press in on
the CLICK STICK to display the ‘Use Current Date’
option and then press in on the CLICK STICK to
activate.
Hunt & Fish Page
‘New Location’ Options
To set the location:
1. Highlight the Location field and then press in on
the CLICK STICK to display the ‘New Location’
options list.
2. Highlight the option desired and then press in on
the CLICK STICK to activate. If you choose
‘Current Location’ the field values displayed on the
page will reflect the times at your current location.
3. If you choose ‘Use Map’, a map page will display.
Use the map pointer to identify the desired location
and then press in on the CLICK STICK.
4. If you choose ‘Use Find Menu’ follow instructions for
using the Find Menu on page 30.
I
52
NOTE: The times displayed are the recognized
best and good times for hunting and Þshing.
But, be certain that they are not in conßict with
state and local game laws which may vary
from location to location. It is your responsibility to know and abide by these laws.
Appendices
SECTION 4
Appendix A
Specifications
Physical
Case:
Fully-gasketed, high-impact plastic alloy, waterproof to IPX7
standards (waterproof to one meter for 30 minutes)
Size:
4.4”H x 2”W x 1.2”D
Weight:
Approx. 5.3 ounces (150g) w/batteries
Temperature Range:
5° to 158°F (-15° to 70°C) (operating)
Performance
Receiver:
Differential-ready, 12 parallel channel
Acquisition time:
Approx. 15 seconds (warm start)
Approx. 45 seconds (EZinit/cold start)
Approx. 5 minutes (First Time/AutoLocate™)
Update Rate:
1/second, continuous
GPS Accuracy:
<15 meters (49 ft) RMS, 95% typical2
DGPS (USGC) Accuracy: 3-5 meters (10-16 ft), 95% typical with DGPS corrections1
DGPS (WAAS) Accuracy: <3 meters (10 ft), 95% typical with DGPS corrections2
Velocity Accuracy:
0.05 meter/sec steady state
Dynamics:
Performs to specifications to 6 g’s
Interfaces:
NMEA 0183, RTCM 104 (for DGPS corrections) and
RS-232 for PC interface
Antenna:
Built-In patch
Power
Input:
Two 1.5-volt AA batteries3
Power Consumption:
0.5 watts max.
Battery Life:
Up to 18 hours of typical use in ‘Battery Saver’ mode4
Specifications subject to change without notice.
1
With optional GARMIN Differential Beacon Receiver Input (such as GARMIN GBR 21 or 23).
2
Subject to accuracy degradation to 100m 2DRMS under the U.S. DoD-imposed Selective Availability
program.
3
The temperature rating for the eTrex Legend may exceed the usable range of some batteries. Alkaline
batteries can rupture at high temperatures. External power can only be applied using the GARMIN Auto
Power Adapter or PC Interface Cable with Auto Power Adapter. These cables contain a 12 VDC to 3 VDC
voltage regulator. Modifications or other applications will void the product warranty.
4
Alkaline batteries lose a significant amount of their capacity as temperature decreases. Use lithium
batteries when operating the eTrex Legend in below-freezing conditions. Extensive use of screen
backlighting will significantly reduce battery life. Different brands of batteries will vary in performance.
53
Appendices
Appendix B
Time Offset
Chart
The table below gives approximate UTC time offset for various longitudinal zones.
If you are in a time zone with daylight savings, add one hour to the offset.
Longitudinal Zone
Offset
Longitudinal Zone
Offset
W180.0° to W172.5°
W172.5° to W157.5°
W157.5° to W142.5°
W142.5° to W127.5°
W127.5° to W112.5°
W112.5° to W097.5°
W097.5° to W082.5°
W082.5° to W067.5°
W067.5° to W052.5°
W052.5° to W037.5°
W037.5° to W022.5°
W022.5° to W007.5°
W007.5° to E007.5°
-12.00
-11.00
-10.00
-09.00
-08.00
-07.00
-06.00
-05.00
-04.00
-03.00
-02.00
-01.00
-00.00
E007.5° to E022.5°
E022.5° to E037.5°
E052.5° to E067.5°
E067.5° to E082.5°
E082.5° to E097.5°
E097.5° to E112.5°
E112.5° to E122.5°
E122.5° to E127.5°
E127.5° to E142.5°
E142.5° to E157.5°
E157.5° to E172.5°
E172.5° to E180.5°
+01.00
+02.00
+03.00
+04.00
+05.00
+06.00
+07.00
+08.00
+09.00
+10.00
+11.00
+12.00
A simple way to determine your local time offset is how many hours you are behind
or ahead of UTC (also called ‘Greenwich’ or ‘Zulu’ time) Example: EST (Eastern
Standard Time) is 5 hours behind UTC, so your offset would be -5. Adding one hour
for daylight savings would make EDT (Eastern Daylight Time) -4. Subtract an hour
for each time zone as you travel west.
Offsets for Continental U.S. would be:
EST: -5
CST: -6
MST: -7
PST: -8
54
EDT: -4
CDT: -5
MDT: -6
PDT: -7
Appendices
Standard Accessories
Carry Lanyard
Appendix C
Accessories
Provides convenient method for carrying the eTrex Legend. Attaches to a
slot on the bottom of the unit. (Not shown)
PC Interface Cable
Allows for transfer of data from a PC to an eTrex Legend. (RS232 serial
port connector) (Not shown)
Owner’s Manual
Quick Start Guide
Optional Accessories
Automotive Mounting Bracket
Automotive Mounting Bracket
Can be temporarily or permanently mounted on the dash.
Handlebar Mounting Bracket
Allows the eTrex Legend to be mounted on bicycle handle bars.
Carrying Case
Protects the eTrex Legend and permits use while in the case. (Not shown)
Handlebar Mounting Bracket
Carrying Holster
Allows easy access to the eTrex Legend when clipped on a belt. (Not shown)
Cigarette Lighter Adapter
Provides eTrex Legend operation from an automobile cigarette lighter.
Data Cable
Wiring harness. Bare wire connections for data input/output. (Not shown)
PC Interface Cable/Cigarette Lighter Power Adapter
Allows transfer of waypoints and routes from a PC to the eTrex Legend
and provides unit operation from an automobile cigarette lighter.
MapSource® Map Data CD-ROMs
An excellent tool for creating waypoints and routes on your PC using a
background map and downloading them to your eTrex Legend. See your
GARMIN dealer for MapSource details.
Replacement Battery Cover
Replacement for lost or damaged battery compartment cover. (Not shown)
These and other GARMIN accessories can be obtained from your GARMIN
Dealer, by contacting GARMIN Customer Service at 913-397-8200, or by
ordering on-line at www.garmin.com.
Cigarette Lighter Power
Adapter-Converts 12VDC
output from the lighter to 3VDC
input to the eTrex Legend.
Not interchangeable with power
adapters for GARMIN VHF
720, 725, and 725e, or GPS
170, 175, 190, and 195.
PC Interface with Cigarette
Lighter Power Adapter.
Also non-interchangeable with
the power adapters
for GARMIN units mentioned
above.
55
Appendices
Appendix D
Wiring Diagram
Interface formats are selected from the Setup ‘Interface
Page’ on page 48 of this manual. The input/output lines
on your eTrex Legend unit are RS-232 compatible, allowing easy interface to a wide range of external devices,
including PC’s, differential beacon receivers, marine autopilots and /or a second GPS receiver.
The NMEA 0183 version 2.3 interface format is supported
by the eTrex Legend and enables the unit to drive up to
three NMEA devices.
NMEA 0183 Version 2.3 Approved Sentences:
GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC,
GPRTE, GPWPL, GPBOD
GARMIN Proprietary Sentences:
PGRME (estimated error), PGRMZ (altitude),
PSLIB (beacon receiver control)
56
Data Cable
Power (+)
Data In
Data Out
Ground (-)
eTrex
Legend
Connector
Data In
Green
Data Out
White
Black
Ground (-)
DGPS (Differential GPS) corrections are accepted in
RTCM SC-104 version 2.0 format through the ‘Data In’
line. The GARMIN GBR 21 is the recommended beacon
receiver for use with the eTrex Legend. Other beacon
receivers with the correct RTCM format may be used, but
may not correctly display status or allow tuning control
from the GPS unit.
The eTrex Legend may be hard-wired to a serial connector using the Data Cable, (see Appendix C for ordering
information). Refer to the wiring diagram and the eTrex
legend unit data connection illustrated below.
The PC Interface Cable provided with this unit allows
you to connect your eTrex Legend to a PC-compatible
computer’s serial port.
Appendices
To resolve problems that cannot be remedied
using this guide: Contact GARMIN Customer Service at
913-397-8200
Appendix E
Troubleshooting
Symptom
Probable Cause
Remedy
Unit does not turn on.
Batteries are exhausted.
Replace batteries.
Unit will not turn ON,
even with new batteries.
Batteries may be installed backwards.
Reinstall batteries.
You are pressing and releasing the
POWER button.
You must press and hold the
POWER button for two seconds.
The unit turns On, then turns Off.
Batteries may be nearly exhausted.
Replace batteries.
It takes more than ten minutes
to get a location fix.
The unit’s view of satellites is
obstructed.
Move to a location with a clear view
of the sky.
Cannot access a WAAS system Your view of the satellite is obstructed Move to a location with a clear view
satellite after 2 to 5 minutes. or you are located too far from satellites and point the unit antenna in the
currently in service for the Americas.
direction of the satellite.
System GPS operation is set to something other than ‘Normal’ and/or interface setting is for RTCM.
Cannot obtain a differential
position from WAAS.
Set system GPS to ‘Normal’ and
interface to other than RTCM.
You have not collected enough infor- Wait 10-20 minutes for the initial colmation from the WAAS satellite.
lection, then 1-2 minutes afterwards.
Cannot access Point of Interest, MetroGuide map data is not activated. Access the Map Setup ‘Map’ option
and activate the check box.
Street, or Intersection Find
Lists.
Cannot view a track being laid
down on the map page when
traveling.
The Track Log feature is turned Off.
Access the Tracks Page, highlight
the ‘ON’ button and press in on the
CLICK STICK.
Cannot see the panning arrow
on the Map Page easily.
There is too much map clutter or the
scale is such that map features are too
densely displayed.
Use the Map Page Setup Page to
reduce map clutter or change the
map scale.
Cannot exit a menu or page by
moving the CLICK STICK to
the left.
Some menus and pages have an ‘X’
Exit on-screen button in the upper
right corner.
Highlight the on-screen button and
then press in on the CLICK STICK
to exit.
The eTrex Legend is programmed to provide “pop-up” messages concerning operational characteristics and
conditions. Press in on the CLICK STICK to acknowledge a message and return to the current feature.
57
Appendices
A
Appendix F
Index
Accessories.... .............................................. 55
Activate a Route .......................................... 37
Altitude (Elevation) ............................... 14, 20
Altitude (Elevation) Entry............................ 14
Antenna .................................................... 2, 3
Arrow, Panning.......................................16-18
AutoZoom................................................... 21
Average Speed ................................. 20, 23, 25
B
Backlight Timer....................................... 4, 47
Backlighting On/Off ............................ 2, 4, 47
Battery Installation/Replacement ................... 3
Battery Level Indicator ............................ 9, 26
Battery Type................................................... 3
Beacon Receiver Setup........................... 48, 56
Bearing.................................................. 20, 23
Bearing Pointer...................................... 12, 23
Big Numbers ......................................... 23, 25
C
Cancel Goto (Stop Navigation) .............. 12, 19
Cautions....................................................ii-iii
Cities, By Name........................................... 32
Cities, Nearest ............................................. 32
CLICK STICK................................................ 2
Compass Ring ......................................... 7, 23
Contrast .............................................. 2, 4, 47
Course................................................... 20, 23
D
Data Entry. .............................................. 2, 10
Date and Time Setup ............................... 9, 45
Detail, Map.................................... 2, 6, 16, 21
Differential GPS (DGPS) ........................ 48, 56
Distance .......................................... 20, 23, 25
E
Elevation ................................... 14, 20, 23, 25
Estimated Time of Arrival (ETA)...... 10, 23, 25
Exit Services................................................ 33
Exits...................................................... 30, 33
Exits, Nearest .............................................. 33
58
F
Features......................................................1-2
Fields, Data ..................................... 17, 19, 20
Find Address....................................30, 35-36
Find Cities............................................. 30, 32
Find Exits.............................................. 30, 33
Find Favorites .................................30, 31-32
Find Intersections.............................30, 35-36
Find Button................................................... 2
Find Menu .................................................. 30
Find Points of Interest ......................30, 34-35
Find Waypoints..................................... 30, 31
G
Global Positioning System (GPS)................. 13
Goto Functions ..................................... 12, 36
Cancelling......................................... 12, 19
H
Heading Selection........................................ 47
I
Initialization ............................................ 3, 13
Installing Batteries ......................................... 3
Interface Page .............................................. 48
L
Language Selection...................................... 49
Location (Marking)...........................10-11, 27
M
Main Menu.............................................. 9, 26
Main Pages .................................................5-9
Main Page Menu............................................ 5
Map Datums................................................ 46
Map Display .......................................... 16, 21
Map Page............................................6, 15-16
Map Page Options ..................................17-22
Map Scale.................................... 2, 11, 16, 21
MapSource Map Data .............................. 4, 55
Mark a Waypoint................................... 10, 27
Mark Waypoint Page ............................. 10, 27
Max Speed................................................... 25
Measuring Between Waypoints........ 12, 17, 42
Moving a Waypoint ..................................... 28
Appendices
Appendix F
Index
N
Navigation Page..............................5, 7, 23-24
Nearest (Waypoints, Cities, Exits, etc.) ...31-35
NMEA ................................................... 48, 56
Normal Mode.............................................. 49
North Up ........................................ 13, 14, 21
North Reference .......................................... 47
O
Odometer (Trip).............................. 20, 23, 25
Offset (Time) ......................................... 45, 54
On-Screen Buttons ........................................ 5
Option Menus ................. 5, 13, 17, 21, 25, 26
Orient Map.................................................. 21
P
Panning (Map) .......................................16-18
Page Button ............................................... 2, 5
Position Format........................................... 46
Projecting a Waypoint ................................. 29
Power Button ................................................ 2
R
Receiver Status ........................................ 3, 13
Renaming a Saved Track.............................. 44
Reset Max Speed ......................................... 25
Routes ....................................................37-42
Creating.................................................. 37
Naming................................................... 37
Options .................................................. 37
Editing...............................................38-41
Inverting (Reversing) .............................. 38
S
Satellite Page ..................................3, 5, 13-14
Saving the Tracklog ................................43-44
Select a Waypoint........................................ 31
Selecting a Page ............................................. 5
Serial Number (External)..... Inside Back Cover
Serial Number (Unit i.d.)............................. 49
Set Course............................................. 23, 37
Software Version (Operating)....................... 49
Specifications .............................................. 53
Speed .............................................. 20, 23, 25
Stop Navigation............................... 12, 24, 41
Sunrise/Sunset............................................. 50
Symbol (Map) ....................................... 11, 27
System Setup............................................... 49
T
Time Format ............................................... 45
Time Offset Chart........................................ 54
Time Zone............................................. 45, 54
TracBack...................................................... 43
TracBack Navigation.................................... 44
Track Logs..............................................43-44
Track Up ............................................... 14, 21
Trip Computer Page .................................... 25
Trip Odometer................................. 20, 23, 25
Trip Timer ................................................... 25
Troubleshooting .......................................... 57
Turning the GPS Receiver “Off” ................... 14
U
Unit Features..............................................1-2
Units of Measure ......................................... 46
Units Page ................................................... 46
UTC Offset ............................................ 45, 54
V
Vertical Speed........................................ 20, 46
View Waypoints on Route ..................... 39, 41
W
Warranty ..................................................... 60
Waypoints List .......................................30-31
Waypoints ..............................................27-29
Deleting .................................................. 29
Editing.................................................... 29
Marking.................................................. 27
Naming................................................... 27
Nearest ................................................... 30
Symbols.................................................. 27
Wide Area Augmentation System (WAAS)... 49
Wiring Diagram (Interface).......................... 56
Z
Zoom In/Out Buttons .............................. 2, 16
59
Appendices
Appendix G
GARMIN
Limited Warranty
GARMIN Corporation warrants this product to be free from defects in materials and
workmanship for one year from the date of purchase. GARMIN will, at its sole option,
repair or replace any components which fail in normal use. Such repairs or replacement
will be made at no charge to the customer for parts or labor. The customer is, however,
responsible for any transportation costs. This warranty does not cover failures due to
abuse, misuse, accident or unauthorized alteration or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING
ANY LIABILITY ARISING UNDER WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE
USE, MISUSE OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE
PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSIONS OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY
TO YOU.
To obtain warranty service, call the GARMIN Customer Service department
(913/397.8200) for a returned merchandise tracking number. The unit should be
securely packaged with the tracking number clearly marked on the outside of the
package, and sent freight prepaid and insured to a GARMIN warranty service station.
A copy of the original sales receipt is required as the proof of purchase for warranty
repairs. GARMIN retains the exclusive right to repair or replace the unit or software or
offer a full refund of the purchase price at its sole discretion. SUCH REMEDY SHALL BE
YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.
60
Product Registration
Help us to better support you by completing our on-line registration today!
Have the serial number of your eTrex Legend handy and connect to our website
(www.garmin.com). Look for the Product Registration link on the Home Page.
Why should you register your eTrex Legend unit?
• Notification of Product Updates
• Notification of New Products
• Lost or Stolen unit tracking
Serial Number
Use this area to record the external serial number (8-digit number located inside the
battery compartment) in case it is lost, stolen, or needs service. Be sure to keep your
original sales receipt in a safe place or attach a photocopy to the inside of the manual.
Serial Number:
*
I
*
NOTE: Do not confuse this external serial number with the internal unit i.d.
that is displayed in the System Setup Page. The internal unit i.d. is relevant to
the operating software and is required only when transferring certain types of
GARMIN MapSource Data to your unit.
© 2001 GARMIN Corporation
GARMIN International, Inc.
1200 E 151st Street, Olathe, KS 66062 U.S.A.
GARMIN (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51, 9AQ U.K.
GARMIN Corp.
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number: 190-00234-00 Rev. B
Download PDF

advertising