Garmin M20M GPS Receiver User Manual

G1000
TM
cockpit reference guide
for the Mooney M20M & M20R
Copyright © 2004, 2005 Garmin Ltd. or its subsidiaries. All rights reserved.
This manual reflects the operation of System Software version 0424.10 or later for the Mooney M20M and M20R. Some differences
in operation may be observed when comparing the information in this manual to earlier or later software versions.
Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Tel: 913/397.8200
Fax: 913/397.8282
Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.
Tel: 503/391.3411
Fax 503/364.2138
Garmin (Europe) Ltd., Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, Hampshire S051 9DL, U.K.
Tel: 44/0870.8501241
Fax: 44/0870.8501251
Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
Tel: 886/02.2642.9199
Fax: 886/02.2642.9099
Web Site Address: www.garmin.com
Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or
stored in any storage medium, for any purpose without the express written permission of Garmin. Garmin hereby grants permission
to download a single copy of this manual and of any revision to this manual onto a hard drive or other electronic storage medium to
be viewed for personal use, provided that such electronic or printed copy of this manual or revision must contain the complete text
of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is
strictly prohibited.
Garmin® is a registered trademark of Garmin Ltd. or its subsidiaries, and G1000™ is a trademark of Garmin Ltd. or its subsidiaries.
These trademarks may not be used without the express permission of Garmin.
NavData® is a registered trademark of Jeppesen, Inc.; Stormscope® and SkyWatch® are registered trademarks of L-3 Communications; and XM® is a registered trademark of XM Satellite Radio, Inc.
May 2005
190-00450-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Printed in the U.S.A.
WARNINGS,
CAUTIONS, & NOTES
WARNING: Navigation and terrain separation must NOT be predicated upon the use of the terrain function.
The G1000 Terrain Proximity feature is NOT intended to be used as a primary reference for terrain avoidance
and does not relieve the pilot from the responsibility of being aware of surroundings during flight. The Terrain
Proximity feature is only to be used as an aid for terrain avoidance and is not certified for use in applications
requiring a certified terrain awareness system. Terrain data is obtained from third party sources. Garmin is
not able to independently verify the accuracy of the terrain data.
WARNING: The displayed minimum safe altitudes (MSAs) are only advisory in nature and should not be relied
upon as the sole source of obstacle and terrain avoidance information. Always refer to current aeronautical
charts for appropriate minimum clearance altitudes.
WARNING: The altitude calculated by G1000 GPS receivers is geometric height above Mean Sea Level and could
vary significantly from the altitude displayed by pressure altimeters, such as the GDC 74A Air Data Computer,
or other altimeters in aircraft. GPS altitude should never be used for vertical navigation. Always use pressure
altitude displayed by the G1000 PFD or other pressure altimeters in aircraft.
WARNING: The Jeppesen database used in the G1000 system must be updated regularly in order to ensure
that its information remains current. Updates are released every 28 days. A database information packet is
included in the G1000 package. Pilots using an outdated database do so entirely at their own risk.
WARNING: The basemap (land and water data) must not be used for navigation, but rather only for non-navigational situational awareness. Any basemap indication should be compared with other navigation sources.
WARNING: Traffic information shown on the G1000 Multi Function Display is provided as an aid in visually
acquiring traffic. Pilots must maneuver the aircraft based only upon ATC guidance or positive visual acquisition
of conflicting traffic.
WARNING: Use of the Stormscope interface for hazardous weather penetration is prohibited. Weather information on the G1000 MFD is approved only for weather avoidance, not penetration.
WARNING: Use of the GDL 69 Weather Interface for hazardous weather penetration is prohibited. Weather
information provided by the GDL 69 is approved only for weather avoidance, not penetration.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
i
WARNINGS,
CAUTIONS, & NOTES
WARNING: NEXRAD weather data is to be used for long-range planning purposes only. Due to inherent delays
in data transmission and the relative age of the data, NEXRAD weather data should not be used for short-range
weather avoidance.
WARNING: The Garmin G1000, as installed in the Mooney M20M and M20R aircraft, has a very high degree
of functional integrity. However, the pilot must recognize that providing monitoring and/or self-test capability
for all conceivable system failures is not practical. Although unlikely, it may be possible for erroneous operation to occur without a fault indication shown by the G1000. It is thus the responsibility of the pilot to detect
such an occurrence by means of cross-checking with all redundant or correlated information available in the
cockpit.
WARNING: For safety reasons, G1000 operational procedures must be learned on the ground.
WARNING: The United States government operates the Global Positioning System and is solely responsible
for its accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy and
performance of all GPS equipment. Portions of the Garmin G1000 utilize GPS as a precision electronic NAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information presented by the G1000 can be misused or
misinterpreted and, therefore, become unsafe.
WARNING: To reduce the risk of unsafe operation, carefully review and understand all aspects of the G1000
Pilot’s Guide documentation and the G1000 Flight Manual Supplement. Thoroughly practice basic operation
prior to actual use. During flight operations, carefully compare indications from the G1000 to all available
navigation sources, including the information from other NAVAIDs, visual sightings, charts, etc. For safety
purposes, always resolve any discrepancies before continuing navigation.
WARNING: The illustrations in this guide are only examples. Never use the G1000 to attempt to penetrate a
thunderstorm. Both the FAA Advisory Circular, Subject: Thunderstorms, and the Airman’s Information Manual
(AIM) recommend avoiding “by at least 20 miles any thunderstorm identified as severe or giving an intense
radar echo.”
CAUTION: The GDU 1040 PFD and MFD displays use a lens coated with a special anti-reflective coating that is
very sensitive to skin oils, waxes, and abrasive cleaners. CLEANERS CONTAINING AMMONIA WILL HARM THE
ANTI-REFLECTIVE COATING. It is very important to clean the lens using a clean, lint-free cloth and an eyeglass
lens cleaner that is specified as safe for anti-reflective coatings.
ii
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
WARNINGS,
CAUTIONS, & NOTES
CAUTION: The Garmin G1000 does not contain any user-serviceable parts. Repairs should only be made by
an authorized Garmin service center. Unauthorized repairs or modifications could void both the warranty and
the pilot’s authority to operate this device under FAA/FCC regulations.
NOTE: When using Stormscope, there are several atmospheric phenomena in addition to nearby thunderstorms
that can cause isolated discharge points in the strike display mode. However, clusters of two or more discharge
points in the strike display mode do indicate thunderstorm activity if these points reappear after the screen has
been cleared.
NOTE: All visual depictions contained within this document, including screen images of the G1000 panel and
displays, are subject to change and may not reflect the most current G1000 system. Depictions of equipment
may differ slightly from the actual equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
iii
WARNINGS,
CAUTIONS, & NOTES
This page intentionally left blank.
iv
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
RECORD OF REVISIONS
Part Number
190-00450-01
Change Summary
Reformat of manual.
Added WX 500 Stormscope
Added XM Weather
Added ADF/DME
Added extended range fuel tanks
Changes in EIS softkey labels
Revision Date of Revision Affected Pages
A
5/25/05
i-Index-2
Description
Initial release
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
v
RECORD OF REVISIONS
This page intentionally left blank.
vi
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
TABLE OF CONTENTS
SECTION 1: SYSTEM OVERVIEW.................................... 1-1
1.1
1.2
1.3
1.4
1.5
PFD/MFD Controls................................................... 1-2
PFD Softkeys............................................................ 1-4
MFD Softkeys .......................................................... 1-6
MFD Page Groups ................................................... 1-8
Backlighting ............................................................. 1-8
SECTION 2: FLIGHT INSTRUMENTS .............................. 2-1
2.1 Airspeed Indicator.................................................. 2-3
Speed Indication ......................................................... 2-3
Speed Ranges ............................................................. 2-3
Airspeed Trend Vector ................................................. 2-3
Vspeed References ...................................................... 2-3
2.2 Attitude Indicator .................................................. 2-3
2.3 Altimeter .................................................................. 2-4
Altitude Reference Bug................................................ 2-4
Altitude Trend Vector ................................................... 2-4
Barometric Setting Box ................................................ 2-4
2.4 Vertical Deviation/Glideslope Indicator ............ 2-4
2.5 Marker Beacon Annunciations ............................ 2-4
2.6 Vertical Speed Indicator ....................................... 2-5
2.7 Horizontal Situation Indicator (HSI) ................... 2-5
Course Pointer ............................................................ 2-6
Course Deviation Indicator (CDI) .................................. 2-6
Bearing Pointers and Information Windows .................. 2-6
DME Radio (optional) .................................................. 2-7
Navigation Source ....................................................... 2-7
SECTION 3: ENGINE INDICATION SYSTEM (EIS).... 3-1
3.1 Engine Display......................................................... 3-1
3.2 Lean Engine Display ............................................... 3-1
Cylinder Select ............................................................ 3-1
3.3 Engine System Display .......................................... 3-2
3.4 Flap & Trim Indications.......................................... 3-2
Rudder Trim Indicator .................................................. 3-2
Elevator Trim Indicator ................................................. 3-2
Flaps Position Indicator ............................................... 3-2
SECTION 4: NAV/COM AND TRANSPONDER .......... 4-1
4.1
4.2
4.3
4.4
Radio Status Indications ....................................... 4-3
Volume ...................................................................... 4-3
Automatic Squelch ................................................. 4-3
Quickly Activating 121.500 MHz .......................... 4-3
4.5 Optional NAV Radios ............................................. 4-3
ADF Radio (optional) ................................................... 4-3
DME Radio (optional) .................................................. 4-4
4.6 Frequency Auto-tuning ......................................... 4-4
Auto-tuning on the PFD .............................................. 4-4
Auto-tuning on the MFD ............................................. 4-4
4.7 Transponder ............................................................. 4-5
Mode Selection ........................................................... 4-5
Ground Mode (Automatic) ...................................... 4-5
Reply Status ........................................................... 4-5
Code Selection ....................................................... 4-5
Flight ID Reporting ...................................................... 4-5
SECTION 5: AUDIO PANEL ................................................ 5-1
5.1 COM Radio Selection ............................................. 5-2
5.2 Marker Beacon Receiver ....................................... 5-2
Marker Beacon Signal Sensitivity ................................. 5-2
5.3 Nav Radio Audio Selection ................................... 5-2
5.4 Intercom System (ICS) Isolation .......................... 5-3
5.5 Intercom Squelch Control ..................................... 5-3
5.6 Digital Clearance Recorder with Playback
Capability ................................................................. 5-4
SECTION 6: AUTOMATIC FLIGHT CONTROL ............. 6-1
SECTION 7: NAVIGATION .................................................. 7-1
7.1 Navigation Map Page ............................................ 7-1
Select the MAP Page Group......................................... 7-1
7.2 Direct-to Navigation .............................................. 7-1
Direct-to Navigation from the MFD .............................. 7-1
Direct-to Navigation from the PFD ............................... 7-2
7.3 Airport Information ............................................... 7-3
Select the Airport Information Page ............................. 7-3
Enter a Waypoint Facility Name or City Location ........... 7-3
Access Runway Information ......................................... 7-3
Access Frequency Information...................................... 7-3
7.4 Intersection Information ...................................... 7-4
Select the Intersection Information Page ...................... 7-4
Access Information on an Intersection ......................... 7-4
7.5 NDB Information..................................................... 7-4
Select the NDB Information Page ................................. 7-4
View Information on a Specific NDB ............................ 7-4
7.6 VOR Information ..................................................... 7-5
Select the VOR Information Page ................................. 7-5
Access Information on a VOR....................................... 7-5
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
vii
TABLE OF CONTENTS
7.7 User Waypoint Information Page ....................... 7-5
7.8 Nearest Airports ..................................................... 7-5
Nearest Airport Information on the MFD ...................... 7-5
Nearest Airports Information on the PFD ...................... 7-6
7.9 Nearest Intersections ............................................ 7-6
Select the Nearest Intersections Page........................... 7-6
View Information on the Nearest Intersection .............. 7-7
7.10 Nearest NDB ............................................................ 7-7
Select the Nearest NDB Page ....................................... 7-7
Access Information on a Specific NDB .......................... 7-7
7.11 Nearest VOR ............................................................. 7-7
Select the Nearest VOR Page ....................................... 7-7
View Information on the Nearest VOR.......................... 7-7
Select and Load a VOR Frequency ................................ 7-8
7.12 Nearest User Waypoint.......................................... 7-8
Select the Nearest User Waypoint Page ........................ 7-8
Select a Nearest User Waypoint ................................... 7-8
7.13 Nearest Frequencies .............................................. 7-8
Select the Nearest Frequencies Page ............................ 7-8
Select and Load the Nearest ARTCC, FSS, or Weather
Frequency ................................................................... 7-9
7.14 Nearest Airspaces ................................................... 7-9
Select the Nearest Airspaces Page................................ 7-9
Airspace Alerts Box ..................................................... 7-9
View Additional Details for a Listed Airspace ................ 7-9
View and Quickly Load the Frequency for a
Controlling Agency ...................................................... 7-9
SECTION 8: FLIGHT PLANNING ...................................... 8-1
8.1 User Defined Waypoints........................................ 8-1
Select the User WPT Information Page ......................... 8-1
Create a New User Waypoint ....................................... 8-1
Create User Waypoints from the Navigation
Map Page ................................................................... 8-1
Modify a User Waypoint .............................................. 8-2
Delete a User Waypoint ............................................... 8-2
8.2 Viewing the Active Flight Plan ............................ 8-2
8.3 Activate a Stored Flight Plan............................... 8-2
8.4 Activate a Flight Plan Leg .................................... 8-2
8.5 Stop Navigating a Flight Plan.............................. 8-3
8.6 Invert Active Flight Plan ....................................... 8-3
8.7 Create a New Flight Plan ...................................... 8-3
Create a new flight plan using the PFD ........................ 8-4
viii
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
Load a Departure ................................................... 8-4
Load an Arrival........................................................ 8-4
Load an Approach .................................................. 8-4
Remove a Departure, Arrival, or Approach
from a Flight Plan ................................................... 8-5
Store A Flight Plan ................................................. 8-5
Edit a Stored Flight Plan ....................................... 8-5
Delete a Waypoint from the Flight Plan............ 8-5
Invert and activate a Stored Flight Plan ........... 8-5
Copy a Flight Plan .................................................. 8-6
Delete a Flight Plan ............................................... 8-6
Graphical Flight Plan Creation ............................ 8-6
Trip Planning............................................................ 8-6
SECTION 9: PROCEDURES ................................................ 9-1
9.1 Arrivals and Departures........................................ 9-1
Load and Activate a Departure Procedure .................... 9-1
Load and Activate An Arrival Procedure ........................ 9-1
9.2 Approaches .............................................................. 9-2
Load and/or Activate an Approach Procedure ............... 9-2
Activate An Approach in the Active Flight Plan ............. 9-3
SECTION 10: HAZARD AVOIDANCE ........................... 10-1
10.1 Customizing the Hazard Displays on the
Navigation Map .................................................... 10-1
10.2 STORMSCOPE® (Optional).................................. 10-1
Displaying Stormscope Lightning Data on the
Navigation Map Page ................................................ 10-1
Stormscope Page....................................................... 10-2
10.3 XM Weather (Optional) ....................................... 10-3
Displaying METAR and TAF information on the
Airport Information Page ........................................... 10-3
Displaying Weather on the Weather Data Link Page ... 10-4
NEXRAD Limitations ............................................. 10-4
Map Panning Information – Weather Data Link Page . 10-5
Weather Product Symbols .......................................... 10-5
Weather Product Age ................................................ 10-6
10.4 Traffic Information Service (TIS) ....................... 10-7
Displaying Traffic on the Traffic Map Page................... 10-7
Displaying Traffic on the Navigation Map ................... 10-7
TIS Audio Alert .......................................................... 10-7
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
TABLE OF CONTENTS
10.5 Skywatch Traffic Advisory System
(TAS)(Optional) ...................................................... 10-8
Displaying Traffic on the Traffic Map Page................... 10-8
Displaying Traffic on the Navigation Map ................... 10-8
10.6 Terrain And Obstacle Proximity ........................ 10-9
Displaying Terrain and Obstacles on the Terrain
Proximity Page .......................................................... 10-9
Displaying Terrain and Obstacles on the
Navigation Map ........................................................ 10-9
SECTION 11: ABNORMAL OPERATION ..................... 11-1
11.1 Reversionary Mode .............................................. 11-1
11.2 Abnormal COM Operation .................................. 11-2
11.3 Unusual Attitudes ................................................. 11-2
SECTION 12: ANNUNCIATIONS & ALERTS .............. 12-1
12.1 Alert Level Definitions ........................................ 12-2
12.2 M20M/M20R Aircraft Alerts ................................ 12-2
Voice Alerts ............................................................... 12-2
Message Advisory Alerts ............................................ 12-2
12.3 G1000 System Annunciations ............................ 12-3
Voice Alerts ............................................................... 12-5
Audio Alerts .............................................................. 12-5
12.4 G1000 System Message Advisories .................. 12-6
MFD & PFD Message Advisories................................. 12-7
Database Message Advisories .................................... 12-8
GMA 1347 Message Advisories ................................. 12-9
GIA 63 Message Advisories ....................................... 12-9
GEA 71 Message Advisories .................................... 12-11
GTX 33 Message Advisories..................................... 12-12
GRS 77 Message Advisories..................................... 12-12
GMU 44 Message Advisories ................................... 12-13
GDL 69 Message Advisories..................................... 12-13
GDC 74A Message Advisories.................................. 12-13
Miscellaneous Message Advisories........................... 12-14
INDEX ...................................................................................Index-1
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
ix
TABLE OF CONTENTS
This page intentionally left blank.
x
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 1
SYSTEM OVERVIEW
SECTION 1: SYSTEM OVERVIEW
The purpose of this Cockpit Reference Guide is to
provide the pilot a resource with which to find operating instructions on the major features of the G1000
system more easily. It is not intended to be a
comprehensive operating guide. Complete operating procedures for the complete system are found in the
following documents:
•
•
•
•
G1000 Primary Flight Display Pilot’s Guide
G1000 VHF NAV/COM Pilot’s Guide
G1000 Transponder Pilot’s Guide
G1000 GMA 1347 Audio Panel Pilot’s Guide and
Supplement
• G1000 Engine Indication System Pilot’s Guide
• G1000 Multi Function Display Pilot’s Guide
• G1000 Optional Equipment Addendum
This guide gives the pilot abbreviated operating instructions for the Primary Flight Display (PFD), Multi
Function Display (MFD), and the GMA 1347 Audio Panel
System.
NOTE: The pilot should read and thoroughly
understand the Mooney M20M/M20R Aircraft
Flight Manual Supplement (AFMS) for limitations, procedures and operational information
not contained in this Cockpit Reference Guide.
The Mooney M20M/M20R Aircraft Flight Manual
Supplement always takes precedence over the
information found in this guide.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
1-1
SECTION 1
SYSTEM OVERVIEW
1.1
PFD/MFD CONTROLS
1
17
2
3
5
4
6
8
9
Figure 1-1 PFD/MFD Controls
10
14
11
15
12
16
13
1-2
7
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 1
SYSTEM OVERVIEW
(1) NAV VOL/ID Knob – Controls the NAV audio level.
Press to toggle the Morse code identifier ON and OFF.
Volume level is shown in the field as a percentage.
(2) NAV Frequency Toggle Key – Toggles the standby
and active NAV frequencies.
(3) Dual NAV Knob – Tunes the MHz (large knob) and
kHz (small knob) standby frequencies for the NAV receiver. Press to toggle the tuning cursor (light blue box)
between the NAV1 and NAV2 fields.
(4) Heading Knob – Turn to manually select a heading
on the HSI. When pressed, it synchronizes the heading
bug with the compass lubber line.
(5) Joystick – Changes the map range when rotated. Activates the map pointer when pressed.
(6) CRS/BARO Knob – The large knob sets the altimeter barometric pressure and the small knob adjusts the
course. The course is only adjustable when the HSI is in
VOR1, VOR2, or OBS/SUSP mode. Pressing this knob
centers the CDI on the currently selected VOR.
(7) Dual COM Knob – Tunes the MHz (large knob) and
kHz (small knob) standby frequencies for the COM transceiver. Pressing this knob toggles the tuning cursor (light
blue box) between the COM1 and COM2 fields.
(8) COM Frequency Toggle Key – Toggles the standby
and active COM frequencies. Pressing and holding this
key for two seconds automatically tunes the emergency
frequency (121.5 MHz) in the active frequency field.
(9) COM VOL/SQ Knob – Controls COM audio level.
Pressing this knob turns the COM automatic squelch ON
and OFF. Audio volume level is shown in the field as a
percentage.
(10) Direct-to Key – Allows the user to enter a destination waypoint and establish a direct course to the selected
destination (specified by the identifier, chosen from the
active route, or taken from the map cursor position).
(11) FPL Key – Displays the active Flight Plan Page for
creating and editing the active flight plan, or for accessing
stored flight plans.
(12) CLR Key (DFLT MAP) – Erases information, cancels an entry, or removes page menus. To display the
Navigation Map Page immediately, press and hold CLR
(MFD only).
(13) Dual FMS Knob – Used to select the page to be
viewed (only on the MFD). The large knob selects a page
group (MAP, WPT, AUX, NRST), while the small knob
selects a specific page within the page group. Pressing the
small knob turns the selection cursor ON and OFF.
(14) MENU Key – Displays a context-sensitive list of options. This list allows the user to access additional features,
or to make setting changes that relate to certain pages.
(15) PROC Key – Selects approaches, departures and arrivals from the flight plan. If a flight plan is used, available procedures for the departure and/or arrival airport
are automatically suggested. If a flight plan is not used,
the desired airport and the desired procedure may be selected. This key selects IFR departure procedures (DPs),
arrival procedures (STARs) and approaches (IAPs) from
the database and loads them into the active flight plan.
(16) ENT Key – Accepts a menu selection or data entry.
This key is used to approve an operation or complete data
entry. It is also used to confirm selections and information entries.
(17) Dual ALT Knob – Sets the reference altitude in the
box located above the Altimeter. The large knob selects
the thousands, while the small knob selects the hundreds.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
1-3
SECTION 1
SYSTEM OVERVIEW
1.2
PFD SOFTKEYS
Softkey ON
TERRAIN – Press to display terrain information
on the inset map.
STRMSCP (optional) – Press to display the Stormscope lightning data on the inset map (within
a 200 nm radius of the aircraft).
NEXRAD (optional) – Press to display NEXRAD
precititation data on the inset map.
XM LTNG (optional) – Press to display the XM
Radio lightning data on the inset map.
BACK – Press to return to the previous level
softkey configuration.
PFD – Press to display the additional softkeys for
additional configurations to the PFD.
METRIC – Press to display the current and reference altitudes in meters, in addition to feet.
Pressing the metric softkey also changes the
barometric setting to hectopascals.
DFLTS – Press to reset default settings on the PFD.
DME (optional) – Press to display the DME information window.
BRG1 (bearing) – Press to cycle through the following Nav sources, making the pointer the indicator for the corresponding source and displaying
the the appropriate information.
Softkey OFF
(optional)
INSET
PFD
OBS
CDI
ADF/DME
XPDR
IDENT
TMR/REF
NRST
ALERTS
Figure 1-2 PFD Top Level Softkeys
INSET – Press to display the Inset Map in the lower
left corner of the PFD.
OFF – Press to remove the Inset Map
DCLTR (3) – Press momentarily to select the
desired amount of map detail. The declutter
level appears adjacent to the DCLTR softkey.
• No declutter: All map features are visible
• Declutter – 1: Declutters land data
• Declutter – 2: Declutters land and SUA data
• Declutter – 3: Declutters large NAV data remaining
(removes everything except the active flight plan)
TRAFFIC – Press to display TIS traffic on the map.
TOPO – Press to display topographical data (i.e.,
coastlines, terrain, rivers, lakes, etc.) and
elevation scale on the inset map.
INSET
OFF
DCLTR
DCLTR-1
TRAFFIC
TOPO
TERRAIN
(optional)
STRMSCP
(optional)
(optional)
NEXRAD
XM LTNG
BACK
ALERTS
Press the BACK or OFF softkey
to return to the top level
softkeys
DCLTR-2
DCLTR-3
Figure 1-3 PFD Softkey Flow Chart – 1
1-4
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 1
SYSTEM OVERVIEW
PFD
(optional)
METRIC
DFLTS
DME
BRG1
360 HSI
ARC HSI
BRG2
STD BARO
BACK
ALERTS
Press the DFLTS softkey to change the PFD
metric values to standard
Press the STD BARO or BACK softkeys
to return to the top level softkeys
Figure 1-4 PFD Softkey Flow Chart – 2
NAV1 – Displays NAV1 waypoint frequency or
identifier and DME information in the BRG1
information window.
GPS – Displays GPS waypoint identifier and GPS
distance information in the BRG1 information
window.
ADF – Displays ADF waypoint frequency in
the BRG1 information window.
OFF – Removes the BRG1 information
window.
360 HSI – Press to display the 360° compass rose.
ARC HSI – Press to display the 140° viewable arc.
BRG2 (bearing) – Press to cycle through the following Nav sources, making the pointer the indicator for the corresponding source and displaying
the the appropriate information.
NAV2 – Displays NAV2 waypoint frequency or
identifier and DME information in the BRG2
information window.
GPS – Displays GPS waypoint identifier and GPS
distance information in the BRG2 information
window.
ADF – Displays ADF waypoint frequency in
the BRG2 information window.
OFF – Removes the BRG2 information
window.
STD BARO – Press to set the barometric pressure
to 29.92 inches of mercury (1013 hPa by
pressing the METRIC softkey).
BACK – Press to return to the previous level
softkeys.
OBS – Press to select OBS mode on the CDI when
navigating by GPS (only available with active leg).
CDI – Press to change navigation mode on the CDI
between GPS, VOR1 and VOR2.
ADF/DME (optional) – Press to display the ADF/DME
Tuning window.
XPDR – Press to display the transponder mode selection softkeys.
STBY – Press to select standby mode.
ON – Press to select mode A.
ALT – Press to select altitude reporting mode.
VFR – Press to automatically squawk 1200 (only
in the U.S.A., refer to ICAO standards for VFR
codes in other countries).
CODE – Press to display transponder code selection
softkeys 0-7.
0 through 7 – Press numbers to enter code.
IDENT – Press to provide special aircraft
position identification to Air Traffic Control
(ATC).
BKSP – Press to remove numbers entered one
at a time.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
1-5
SECTION 1
SYSTEM OVERVIEW
(optional)
OBS
ADF/DME
CDI
XPDR
TMR/REF
IDENT
NRST
ALERTS
CDI (VOR1)
CDI (VOR2)
Press the BACK softkey
to return to the top level
softkeys
GPS
ALT
ON
STBY
VFR
CODE
IDENT
BACK
ALERTS
Press the BACK
softkey
to return to
the top level
softkeys
0
1
2
3
4
5
7
6
IDENT
BKSP
BACK
ALERTS
Figure 1-5 PFD Softkey Flow Chart – 3
BACK – Press to return to the previous level
softkeys.
IDENT – Press to provide special aircraft position
identification to Air Traffic Control (ATC).
BACK – Press to return to the previous level
softkeys.
IDENT – Press to provide special aircraft position
identification to Air Traffic Control (ATC).
TMR/REF – Press to display the Timer/References
window.
NRST – Press to display the Nearest Airports
window.
ALERTS – Press to display the Alerts window.
1-6
1.3
MFD SOFTKEYS
ENGINE – Pressing this softkey makes available the
LEAN and SYSTEM softkeys which in turn access
the Lean Page and the System Page, respectively.
MAP – pressing this softkey enables the following
softkeys:
TRAFFIC – pressing this softkey displays/
removes Traffic on the Navigation Map.
TOPO – pressing this softkey displays or
removes topographic information on the
Navigation Map.
TERRAIN – pressing this softkey displays/
removes terrain and obstacle data on the
Navigation Map.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 1
SYSTEM OVERVIEW
STRMSCP (optional) – pressing this softkey
displays/removes Stormscope lightning
data on the Navigation Map.
NEXRAD (optional) – pressing this softkey
displays/removes precipitation data on the
Navigation Map.
XM LTNG (optional) – pressing this softkey
displays/removes XM Radio lightning data
on the Navigation Map.
BACK – pressing this softkey displays the
ENGINE and MAP top level softkeys.
DCLTR (declutter) – pressing this softkey removes
map information in three levels.
CHKLIST (checklist)(optional) – pressing the
CHKLIST softkey displays the Checklist Page.
DCLTR
MAP
ENGINE
CHKLIST
(optional)
Press the BACK softkey on this level to
return to the top softkey level
ENGINE
LEAN
SYSTEM
DCLTR-1
BACK
DCLTR-2
DCLTR-3
Press to return to the
top softkey level
TRAFFIC
ENGINE
LEAN
SYSTEM
DEC FUEL
INC FUEL
RST FUEL
TOPO
SYSTEM
CYL SLCT
ASSIST
(optional)
(optional)
STRMSCP
NEXRAD
XM LTNG
BACK
The DONE softkey changes to UNDO when the checklist
item is already checked
ENGINE
LEAN
(optional)
BACK
Press the ENGINE or BACK softkey on any level to
return to the default page level
ENGINE
TERRAIN
DONE
EXIT
EMERGCY
BACK
CLR
ENGINE
MAP
DCLTR
CHKLIST
Figure 1-6 MFD Softkeys
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
1-7
SECTION 1
SYSTEM OVERVIEW
1.4
MFD PAGE GROUPS
1.
Turn the large FMS knob until the desired page
group is selected.
2.
Turn the small FMS knob to select pages within
the group. See Figure 1-7.
Nearest Group
Auxiliary Page Group
Number of Pages in Current
Group
Waypoint Page Group
Map Page Group
Figure 1-7 Page Group Icon
1.5
Selected Page
BACKLIGHTING
To manually adjust the backlight for the
PFD and MFD:
1-8
1.
Press the MENU key on the PFD to display the
PFD Setup Menu window.
2.
Press the small FMS knob to activate the
cursor. ‘PFD DSPL > AUTO’ is now highlighted.
3.
Turn the small FMS knob to display the
selection window.
4.
Turn either FMS knob to select ‘MANUAL’, then
press the ENT key.
5.
With the intensity value now highlighted, turn
the small FMS knob to select the desired
backlighting.
6.
Turn the large FMS knob to highlight ‘MFD
DSPL > AUTO’ and repeat steps 3 through 5.
Figure 1-8 PFD Setup Menu Window
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 2
FLIGHT INSTRUMENTS
SECTION 2: FLIGHT INSTRUMENTS
1
16
15
14
13
2
12
11
3
10
4
9
8
5
7
6
1
NAV Frequency Window
9
Turn Rate Indicator
2
Airspeed Indicator
10
Barometric Setting Box
3
True Airspeed Box
11
Vertical Speed Indicator
4
Heading Box
12
Altimeter
5
Horizontal Situation Indicator
13
Altitude Reference Box
6
Outside Air Temperature Box
14
COM Frequency Window
7
System Time Box
15
Navigation Status Bar
8
Transponder Status Bar
16
Slip/Skid Indicator
Figure 2-1 Default PFD Information
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
2-1
SECTION 2
FLIGHT INSTRUMENTS
10
1
9
2
8
3
7
4
5
6
1
Traffic Annunciation
7
Alerts Window
2
Selected Heading Box
8
Selected Course Box
3
Inset Map
9
Vertical Deviation/Glideslope Indicator
4
BRG1 Information Window
10
Marker Beacon Annunciation
5
DME Information Window
6
BRG2 Information Window
Figure 2-2 Additional PFD Information
Distance to Next Waypoint
Next Waypoint
Desired Track to
Next Waypoint
Current Track
Figure 2-3 PFD Navigation Status Window
2-2
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 2
FLIGHT INSTRUMENTS
2.1
AIRSPEED INDICATOR
Vspeed References
Airspeed Trend
Vector
Actual Airspeed
Vspeed
References
Speed Ranges
True Airspeed
Box
Figure 2-4 Airspeed Indicator
Vspeeds are set using the TMR/REF softkey. Glide, Vr,
Vx and Vy are shown on the References window. When
active (ON), the Vspeeds are displayed at their respective
locations to the right of the airspeed scale.
2.2
ATTITUDE INDICATOR
The Slip/Skid Indicator is located under the roll pointer and moves laterally away from the pointer to indicate
lateral acceleration. One Slip/Skid indicator displacement
is equal to one ball displacement when compared to a traditional slip/skid indicator.
10
Speed Indication
The indicated airspeed is displayed inside the black
pointer. The pointer will become red upon reaching
Vne.
9
1
8
2
7
3
6
4
5
Figure 2-5 Red Pointer at Vne
Speed Ranges
The color coded speed range strip denotes flaps operating range, normal operating range, and never exceed
speed (Vne). A red range is also present for low speed
awareness. Refer to the Airplane Flight Manual (AFM) for
airspeed limitations and indicator markings.
Airspeed Trend Vector
The end of the trend vector displays approximately
what the airspeed will be in 6 seconds if the current rate
of acceleration/decelaration is maintained.
1
Roll Pointer
6
Aircraft Wing Tips
2
Roll Scale
7
Pitch Scale
3
Horizon Line
8
Slip/Skid Indicator
4
Aircraft Symbol
9
Sky Representation
5
Land Representation
10
Roll Index
Figure 2-6 Attitude Indicator
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
2-3
SECTION 2
FLIGHT INSTRUMENTS
2.3
ALTIMETER
Barometric Setting Box
Altitude Reference
Box
To set barometric pressure, turn the BARO knob to
select the desired setting.
2.4
Altitude Trend
Vector
Current Altitude
The Vertical Deviation/Glideslope Indicator appears
when an ILS is tuned in the active NAV field.
2.5
Altitude Reference Bug
Barometric Setting
Box
Figure 2-7 Altimeter
VERTICAL DEVIATION/GLIDESLOPE
INDICATOR
MARKER BEACON ANNUNCIATIONS
Marker Beacon
Annunciation
Altitude Reference Bug
The Altitude Reference Bug can be set to any desired
altitude. The bug acts as a visual reference to indicate the
desired altitude is approaching.
Vertical
Deviation/Glideslope
Indicator
To set the altitude reference bug:
1.
Turn the ALT knobs to set the altitude reference
bug. The small ALT knob sets the hundreds and
the large ALT knob sets the thousands. This
altitude also appears in the altitude reference
box above the altimeter.
Figure 2-8 Marker Beacon and Vertical Deviation
Altitude Trend Vector
The end of the trend vector displays approximately
what the altitude will be in 6 seconds if the current rate of
vertical speed is maintained.
2-4
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 2
FLIGHT INSTRUMENTS
2.6
VERTICAL SPEED INDICATOR
14
13
1
Vertical Speed Pointer
12
2
11
3
10
4
9
8
5
7
6
Figure 2-9 Vertical Speed Indicator
2.7
HORIZONTAL SITUATION INDICATOR
(HSI)
The HSI compass can be displayed as a 360° rose or
140° arc by pressing the PFD softkey, followed by the 360
HSI or the ARC HSI softkey.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Turn Rate Indicator
Lateral Deviation Scale
Navigation Source
Aircraft Symbol
Course Deviation Indicator
Rotating Compass Rose
OBS Mode
TO/FROM Indicator
Heading Bug
Course Pointer
Flight Phase
Turn Rate and Heading Trend Vector
Heading
Lubber Line
Figure 2-10 Horizontal Situation Indicator
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
2-5
SECTION 2
FLIGHT INSTRUMENTS
Turn Rate Indicator and Heading Trend Vector
Bearing Pointers and Information Windows
Each tick mark is at 9 (half standard rate tick mark)
and 18 (standard rate tick mark) degrees to the left and
right of the lubber line. A wide magenta line displays the
current turn rate, up to 24 degrees. A magenta arrowhead appears at 25 degrees. This trend vector provides
the pilot with a prediction of what the heading will be in
6 seconds at the present turn rate.
Pressing the PFD softkey provides access to the BRG1
and BRG2 softkeys. The BRG1 pointer is a single line
pointer. The BRG2 pointer is a double line pointer.
DME
Information Bearing 1
Pointer
Window
Bearing 2
Pointer
Figure 2-14 Turn Rate Indicator and Heading Trend Vector
Course Pointer
The course pointer is a single line arrow (GPS, VOR1
and LOC1) or double line arrow (VOR2 and LOC2) which
points in the direction of the set course.
Bearing 1
Information
Window
Bearing 2
Information
Window
Figure 2-14 HSI with Bearing Information
Distance to
Bearing Source
Waypoint
Identifier
Course Deviation
Lateral Deviation
TO/FROM Indicator
Scale
Figure 2-15 Arc CDI and Compass Rose CDI
Course Deviation Indicator (CDI)
The CDI scale automatically adjusts to the current
phase of flight (enroute 5.0 nm, terminal area 1.0 nm,
or approach 0.3 nm). Scaling may be selected manually
from the MFD System Setup Page.
2-6
Bearing
Pointer
Source
Icon
Figure 2-15 BRG1 Information Window
Distance to
Bearing Source
Waypoint
Identifier
Bearing
Pointer
Source
Icon
Figure 2-16 BRG2 Information Window
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 2
FLIGHT INSTRUMENTS
DME Radio (optional)
To display the DME Information Window, press the
PFD softkey followed by the DME softkey.
Figure 2-17 DME Information Window
Navigation Source
To change between navigation sources:
1.
Press the CDI softkey to change from GPS to
VOR1/LOC1.
2.
Press the CDI softkey again to change from
VOR1/LOC1 to VOR2/LOC2.
3.
Press the CDI softkey a third time to return to
GPS.
When using GPS as the navigation source, the following may appear:
• INTEG – RAIM is not available
• WARN – GPS detects a position error
• SUSP – Displayed when in OBS Mode indicating
GPS navigation is suspended.
Figure 2-18 GPS INTEG, GPS SUSP, LOC1 and VOR2
To enable/disable OBS mode while navigating
with GPS:
1.
Press the OBS softkey to select OBS Mode.
2.
Turn the CRS knob to select the desired course
TO/FROM the waypoint.
3.
Press the OBS softkey again to return to normal
operation.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
2-7
SECTION 2
FLIGHT INSTRUMENTS
.
This page intentionally left blank.
2-8
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 3 – ENGINE
INDICATION SYSTEM (EIS)
SECTION 3: ENGINE INDICATION
SYSTEM (EIS)
3.1
3.2
LEAN ENGINE DISPLAY
ENGINE DISPLAY
In all cases green indicates normal operation, yellow
indicates caution, and red indicates warning.
Mooney M20R Engine displays are shown in this section. The M20M displays are similar with the exception of
showing the Turbine Inlet Temperature (TIT).
Pressing the ENGINE softkey makes available the
LEAN and SYSTEM softkeys which in turn provide access the Lean Page and the System Page, respectively.
Manifold
Pressure
Gauge
RPM Gauge
Fuel Quantity
Indicator
Fuel Flow
Indicator
Oil Pressure
Indicator
Fuel Flow
Readout
Exhaust Gas
Temperature
Bar Graph
EGT Readout
For Selected
Cylinder
Cylinder Head
Temperature
Bar Graph
CHT Readout
For Selected
Cylinder
Figure 3-2 M20R LEAN Engine Page
Cylinder Select
Oil Temperature
Indicator
Cylinder Head
Temperature
Indicator
Voltmeter
Ammeter
Figure 3-1 M20R Default Engine Page
In aircraft with the extended range 55 gallon tanks
option, the fuel quantity will still show 45 gallons when
full.
The CYL SLCT softkey can be utilized to obtain information about a particular cylinder.
The CYL SLCT softkey becomes disabled when a particular cylinder turns yellow or red, until the temperature
decreases and returns to normal or when the ASSIST
softkey is pressed.
Pressing the ASSIST softkey causes the first cylinder
that peaks to become hightlighted and information for
that cylinder to be displayed.
Any exceedance of default Engine Page parameters,
while viewing the Lean Engine Page, will cause the display
to automatically switch back to the default Engine Page.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
3-1
SECTION 3 – ENGINE
INDICATION SYSTEM (EIS)
3.3
ENGINE SYSTEM DISPLAY
If desired, use the DEC FUEL, INC FUEL and RST
FUEL softkeys to adjust the amount of fuel remaining for
totalizer calculations.
NOTE: Fuel calculations do not use the aircraft
fuel quantity indicators, and are calculated from
the last time the fuel was reset.
3.4
FLAP & TRIM INDICATIONS
The flap and trim indicators are located on the MFD
next to the engine indicating displays.
Rudder Trim Indicator
Actual trim position is shown using a blue inverted
triangle. The ‘takeoff’ rudder trim position is shown in
white.
Elevator Trim Indicator
Trim position is shown by a blue triangle. A white
block indicates ‘takeoff’ elevator trim position.
Flaps Position Indicator
The Flaps Position Indicator shows the current position of the flaps. The three possible positions, up, takeoff, and down, are depicted in cyan as ‘UP’, ‘T/O’, and
‘DN’, respectively. During flaps position transition, ‘///’ is
displayed in the window.
Aircraft Total
Time in Service
Fuel Remaining
Flap
Position
Rudder Trim
Takeoff Position
Elevator Trim
Takeoff Position
Trim Position
Indicator
Figure 3-3 M20R SYSTEM Engine Page
Any exceedance of default Engine Page parameters,
while viewing the System Engine Page, will cause the display to automatically switch back to the default Engine
Page.
3-2
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 4 – NAV/COM &
TRANSPONDER
SECTION 4: NAV/COM AND
TRANSPONDER
The Nav/Com controls and frequency windows are located on the Primary Flight Display and the Multi-Function Display in the same locations.
NAV
Controls
NAV Frequency Window
COM Frequency Window
COM
Controls
Figure 4-1 G1000 VHF NAV/COM Interface (PFD)
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
4-1
SECTION 4 – NAV/COM &
TRANSPONDER
Standby NAV
Frequency Field
Tuning Box
Selected NAV
Frequency
Active NAV
Frequency Field
Navigation Status Window
Selected COM
Frequency
Figure 4-2 Frequency Fields
Frequency Toggle Arrow
Active COM
Frequency Field
Tuning Box
Figure 4-3 Frequency Toggle Arrow and Tuning Box
NAV Controls
COM Controls
VOL/PUSH
ID Knob
VOL/PUSH
SQ Knob
Frequency Toggle Key
Dual NAV
Knob
Dual COM
Knob
• Turn to tune in desired
frequencies.
• Press to change tuning box
positions.
Figure 4-4 NAV/COM Controls
4-2
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Standby COM
Frequency Field
Tuning Box
SECTION 4 – NAV/COM &
TRANSPONDER
4.1
RADIO STATUS INDICATIONS
4.5
OPTIONAL NAV RADIOS
• TX – When a COM radio is keyed, a white TX
indication appears to the right of the corresponding
COM frequency.
The Tuning window is displayed by pressing the ADF/
DME softkey (if no ADF is installed, the softkey will be
labeled DME).
• ID – When the Morse code identifier is ON for a
NAV radio, a white ID indication appears to the left
of the corresponding active NAV frequency. The
Morse code identifier can be heard if the corresponding NAV radio is selected on the audio panel.
ADF Radio (optional)
Figure 4-5 Radio Status Indications
4.2
Figure 4-6 COM Volume Level
From the Tuning window, turn the large FMS
knob to highlight the ADF tuning field.
2.
Turn the small FMS knob to enter the first
digit.
3.
Turn the large FMS knob to select the next
desired digit field. Turn the small FMS knob to
again select the desired digit.
4.
When the desired frequency is entered press
the ENT key to transfer the frequency into the
active field.
5.
Turn the large FMS knob to select the MODE
field. Turn the small FMS knob to select ADF
or BFO.
6.
Turn the large FMS knob to select the volume
field if desired. Turn the small FMS knob to
adjust the ADF volume to the desired level.
7.
Press the FMS knob to exit all the fields.
AUTOMATIC SQUELCH
Automatic squelch can be disabled for a COM radio by
pressing the COM knob to select the desired COM subwindow, then by pressing the VOL/PUSH SQ knob.
4.4
1.
VOLUME
‘VOLUME’ is displayed in place of the associated radio
name (i.e., ‘COM1’ or ‘NAV2’) for two seconds after the
volume level is last changed.
4.3
To tune the ADF:
QUICKLY ACTIVATING 121.500 MHZ
Pressing and holding the COM Frequency Toggle key
for approximately two (2) seconds automatically tunes the
selected COM radio to the emergency frequency.
Figure 4-7 ADF/DME Tuning Window
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
4-3
SECTION 4 – NAV/COM &
TRANSPONDER
4.6
DME Radio (optional)
FREQUENCY AUTO-TUNING
Auto-tuning on the PFD
Figure 4-8 Radio Tuning Window
To change the DME tuning source:
Figure 4-10 Nearest Airports Window (PFD)
1.
From the Tuning window, turn the large FMS
knob to highlight the DME source field.
1.
2.
Turn the small FMS knob to display the selection window. Turn the FMS knob to select the
desired mode and press the ENT key.
Press the NRST softkey to display the Nearest
Airports Window.
2.
Turn the FMS knobs to highlight the desired
frequency.
3.
Press the ENT key to place the frequency in the
standby field of the active COM.
4.
Press the Frequency Toggle key to place the
frequency in the active field.
Figure 4-9 DME Selection Window
NAV frequencies are entered automatically in the NAV
window upon approach loading or approach activation.
Auto-tuning on the MFD
Auto-tuning on the MFD is done in much the same
way as on the PFD. Use the FMS knobs to select the desired frequency on any of the information pages. Pressing
the ENT key then loads the selected frequency into the
standby frequency window of the appropriate radio.
4-4
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 4 – NAV/COM &
TRANSPONDER
4.7
TRANSPONDER
Mode Selection
The STBY, ON and ALT softkeys can be accessed by
pressing the XPDR softkey.
Ground Mode (Automatic)
GND is displayed when the aircraft is on the ground.
Figure 4-11 Ground Mode
Reply Status
When the transponder sends replies to interrogations,
an “R” indication appears momentarily in the reply status
field.
Following is a list of important codes:
• 1200 – VFR code in the U.S. (please refer to the
ICAO standards for VFR codes in other countries).
• 7000 – VFR code commonly used in Europe
(please refer to the ICAO standards).
• 7500 – Hijack code.
• 7600 – Loss of communication code.
• 7700 – Emergency code.
• 7777 – Military interceptor operations code
(NEVER ENTER THIS CODE).
• 0000 – Code for military use (in the U.S.).
Flight ID Reporting
If so configured, the Flight ID may be entered in the
Timer/Reference window. If configuration is set to “SAME
AS TAIL” the aircraft tail number will always be displayed.
Figure 4-12 Reply Indication
Code Selection
1.
Press the XPDR softkey to display the transponder Mode Selection softkeys.
2.
Press the CODE softkey to display the transponder Code Selection softkeys, which includes the
digit softkeys.
3.
Press the appropriate digit softkeys to enter
the code in the four-digit code field of the
Transponder Status bar. Five seconds after the
fourth digit has been entered, the transponder
code becomes activated.
Flight ID
Figure 4-13 Timer/References Window
When entering a code, press the BKSP softkey as needed to back up and change code
digits.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
4-5
SECTION 4 – NAV/COM &
TRANSPONDER
This page intentionally left blank.
4-6
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 5 – AUDIO PANEL
SECTION 5: AUDIO PANEL
Transceiver Audio
(COM 3 is unavailable)
Transmitters
(COM3 MIC is unavailable)
Split COM
(Not recommended for use
in the M20M/M20R
Telephone (Unavailable)
Passenger Address
Speaker
Marker Beacon/Mute
Marker Beacon Signal Sensitivity
Aircraft Navigation Radio Audio
(ADF & DME optional, AUX
unavailable)
Manual Squelch
Aircraft Navigation Radio Audio
Recorded COM Audio Playback
ICS Isolation
VOL/SQ
Volume/Squelch
VOL Annunciation
SQ Annunciation
Reversionary Mode
Figure 6-1 Audio Panel Controls
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
5-1
SECTION 5 – AUDIO PANEL
5.1
COM RADIO SELECTION
Marker Beacon Signal Sensitivity
Pressing the COM1 MIC or COM2 MIC key selects
the active transmitter (i.e., microphone). The associated
receiver audio (COM1 or COM2) also becomes selected
when the COM MIC key is pressed.
To prevent deselecting the desired received audio
when pressing another COM MIC key, press the already
selected COM1 or COM2 key before pressing the other
COM MIC key.
Figure 5-4 Marker Beacon
5.3
NAV RADIO AUDIO SELECTION
Pressing DME, ADF, NAV1, or NAV2 selects and
deselects the radio source and activates the annunciator. Selected audio can be heard over the headset and the
speakers. These four keys can be selected individually or
together.
Figure 5-2 Transceivers
5.2
The HI SENS key can be pressed for increased marker
beacon signal sensitivity.
MARKER BEACON RECEIVER
The marker beacon receiver is always ON. Figure 5-3
shows the marker beacon annunciators on the PFD
Inner Marker
Annunciator
Middle Marker
Annunciator
Figure 5-3 Marker Beacon Signal Indicator Lights on the PFD
When the MKR/MUTE key is pressed, the key annunciator is lit and the audio tone can be heard over the
speaker or headsets during marker reception.
When the tone is active, pressing the MKR/MUTE key
mutes the audio but does not affect the annunciator. The
audio returns when the next marker signal is received.
5-2
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Outer Marker
Annunciator
SECTION 5 – AUDIO PANEL
5.5
INTERCOM SQUELCH CONTROL
Select manual squelch for intercom audio by pressing
the MAN SQ key to light the annunciator.
Figure 5-5 Navigation Radios
5.4
INTERCOM SYSTEM (ICS) ISOLATION
Pressing the small VOL/SQ knob now toggles between volume and squelch adjustment by lighting VOL
or SQ respectively.
Press the PILOT and/or COPLT key to select who is
isolated from hearing the Nav/Com radios and music. Selection scenarios are addressed in Table 5-1.
Figure 5-6 ICS Isolation
Figure 5-7 Volume/Squelch Control
Mode
PILOT KEY
ANNUNCIATOR
COPLT KEY
ANNUNCIATOR
Pilot Hears
Copilot Hears
Selected radios;
pilot; copilot;
passengers;
MUSIC 1
Passenger
Hears
Selected radios;
pilot; copilot;
passengers;
MUSIC 2
Copilot;
passengers;
MUSIC 1
Copilot;
passengers;
MUSIC 2
ALL
OFF
OFF
Selected radios;
pilot; copilot;
passengers;
MUSIC 1
PILOT
ON
OFF
Selected radios;
pilot
Copilot
Selected radios;
pilot; passengers;
MUSIC 2
Selected radios;
pilot; copilot
Passengers;
MUSIC 2
COPILOT
OFF
ON
Selected radios;
pilot; passengers;
MUSIC 1
CREW
ON
ON
Selected radios;
pilot; copilot
Table 5-1 ICS Isolation Modes
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
5-3
SECTION 5 – AUDIO PANEL
5.6
DIGITAL CLEARANCE RECORDER
WITH PLAYBACK CAPABILITY
Each reception of primary active COM audio is automatically recorded in a memory block. When the next
transmission is received, it is recorded in the next memory
block, and so on. Once the 2.5 minutes of recording time
has been reached, the recorder begins recording over the
stored memory blocks, starting from the oldest block.
Powering off the unit automatically clears all recorded
blocks.
Figure 5-8 Playback
• Pressing PLAY once plays back the latest recorded
memory block, then returns to normal operation.
• Pressing PLAY during playback of a memory block
halts the playback of this block and plays back the
preceding recorded block. The PLAY key can be
used to backtrack through the recorded memory
blocks to reach and play back any desired block.
Pressing the MKR/MUTE key during playback
halts playback and returns the recorder/playback
to normal operation.
If a COM input signal is detected during playback,
playback is halted and the new COM input signal is recorded as the latest block.
5-4
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 6 – AUTOMATIC
FLIGHT CONTROL
SECTION 6: AUTOMATIC FLIGHT
CONTROL
Refer to the pilot’s guide for the installed autopilot system.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
6-1
SECTION 6 – AUTOMATIC
FLIGHT CONTROL
This page intentionally left blank.
6-2
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 7 – NAVIGATION
SECTION 7: NAVIGATION
7.2
DIRECT-TO NAVIGATION
Direct-to Navigation from the MFD
7.1
NAVIGATION MAP PAGE
Select the MAP Page Group
1.
2.
3.
Turn the large FMS knob until MAP is highlighted in the page group window in the lower
right of the MFD display.
Identifier
Facility Name
City
Nearest Airport
Flight Plan Field
Map Orientation
Map of the
Selected
Waypoint
Turn the small FMS knob to select the first MAP
page (indicated by a solid rectangular icon).
Map Range
Press the MAP softkey to display softkeys for the
available information which may be displayed
on the map.
WARNING: The map display should only be
used for situational awareness. Any map display
indication should be compared with approved
navigation sources.
Symbol
Region
Latitude/
Longitude
Activate Field
Bearing
Distance
Direct-to
Course
Figure 7-2 MFD Direct-to Window
To enter a Direct-to destination:
1.
Press the Direct-to (
2.
Turn the small FMS knob to enter the first letter
of the destination waypoint identifier. Turn the
large FMS knob to the right to move the cursor
to the next character position.
3.
Repeat step 2 to spell out the rest of the waypoint identifier.
4.
Press the ENT key to confirm the identifier. The
‘Activate?’ field is highlighted.
5.
Press the ENT key to activate.
) key.
To select a Direct-to destination to a flight
plan waypoint or nearest airport:
Figure 7-1 Navigation Map Page
1.
Press the Direct-to (
2.
Turn the large FMS knob to highlight the Flight
Plan Field or Nearest Airport Field.
3.
Turn the small FMS knob to display a list waypoints or airports.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
) key.
7-1
SECTION 7 – NAVIGATION
4.
5.
Continue turning the small FMS knob to scroll
through the list and highlight the desired
waypoint or airport.
Press the ENT key to confirm the selection.
Press ENT again to activate a Direct-to.
To re-center the CDI (HSI) needle to the
same destination waypoint:
1.
) key, followed by
Press the Direct-to (
pressing the ENT key twice. NOTE: If a missed
approach point (MAP) is the current destination, the approach will be canceled.
Direct-to Navigation from the PFD
WPT Symbol
WPT Location
Identifier
Facility Name
Flight Plan WPT
Bearing to WPT
Distance from WPT
Course to Selected WPT
Nearest WPT
Lat/Lon
Figure 7-4 PFD Direct-to Window
1.
Press the Direct-to key (
2.
Turn the large FMS knob to place the cursor in
the desired selection field.
3.
Turn the small FMS knob to begin selecting the
desired identifier, location, etc.
4.
Press the ENT key.
The cursor is now flashing on ‘ACTIVATE?’.
Press the ENT key again to activate.
To manually define the Direct-to course:
1.
Press the Direct-to (
2.
Turn the FMS knobs to select the destination
waypoint.
3.
Press the ENT key to confirm the selected waypoint, then turn the large FMS knob to highlight
the Direct-to Course field.
5.
4.
Turn the FMS knobs to select the desired course
and press the ENT key.
1.
Press the Direct-to (
5.
Press the ENT key again to begin navigation
using the selected destination and course.
2.
Press the MENU key to display the Options
Window. The cursor will be flashing on ‘Cancel
Direct-to NAV’.
3.
Press the ENT key to cancel the direct-to.
) key.
Canceling Direct-to Navigation:
) key.
1. Press the Direct-to (
2.
Press the MENU key to display the Direct-to
options menu.
3.
With ‘Cancel Direct-To NAV’ highlighted, press
the ENT key. If a flight plan is still active, the
G1000 resumes navigating the flight plan
along the closest leg.
Cancelling Direct-to Navigation:
Figure 7-3 Canceling Direct-to Navigation
7-2
).
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
) key.
SECTION 7 – NAVIGATION
7.3
AIRPORT INFORMATION
7.
To remove the flashing cursor, press the FMS
knob.
Access Runway Information
1.
Press the FMS knob to activate the cursor.
2.
Turn the large FMS knob to place the cursor on
the Runways field.
3.
Turn the small FMS knob to display the next
runway for the selected airport.
4.
Continue turning the small FMS knob to select
the desired runway.
5.
To remove the flashing cursor, press the FMS
knob.
Access Frequency Information
Figure 7-5 Airport Information Page
Select the Airport Information Page
1. Turn the large FMS knob to select the ‘WPT’ page
group. Turn the small FMS knob to select the first
rectangular page icon.
Enter a Waypoint Facility Name or City
Location:
1.
Press the FMS knob to activate the cursor.
2.
Turn the large FMS knob to select the facility
name or location (city) field.
3.
Turn the small FMS knob to select the desired
character.
4.
Turn the large FMS knob to select the next
character field.
5.
Repeat steps 3 and 4 until the facility name or
location is selected, then press the ENT key. If
there are duplicate names in the database, a
list is displayed from which to chose the desired
location.
1.
Press the FMS knob to activate the cursor.
2.
Turn the large FMS knob to move the cursor to
the Frequencies window.
3.
Turn either FMS knob to scroll through the list,
placing the cursor on the desired frequency.
4.
Press the ENT key to place the selected frequency in the standby field of the ‘COM’ or
‘NAV’ window.
To remove the flashing cursor, press the FMS
knob.
• ‘TX’ – transmit only, RX - receive only
• ‘PT’ – part time frequency
• ‘i’ – additional information exists, press the ENT
key
If a listed frequency has sector or altitude restrictions,
the frequency is preceded by an info designation.
5.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
7-3
SECTION 7 – NAVIGATION
7.4
INTERSECTION INFORMATION
7.5
NDB INFORMATION
Select the Intersection Information Page
1.
Turn the large FMS knob to select the WPT page
group.
2.
Turn the small FMS knob to select the second
rectangular page icon.
Figure 7-7 NDB Information Page
Select the NDB Information Page
1.
Turn the large FMS knob to select the WPT page
group.
2.
Turn the small FMS knob to select the third
rectangular page icon
Figure 7-6 Intersection Information Page
Access Information on an Intersection
1.
7-4
With the Intersection Information Page displayed, press the FMS knob to activate the
cursor.
2.
Turn the FMS knobs to enter a name for the
identifier and press the ENT key.
3.
Press the FMS knob to remove the flashing
cursor.
View Information on a Specific NDB:
1.
With the NDB Information Page displayed,
press the FMS knob to activate the cursor.
2.
Turn the large FMS knob to highlight the
desired selection field (identifier, name or closest city).
3.
Turn the FMS knobs to enter an identifier, name
or city and press the ENT key.
4.
Press the FMS knob to remove the flashing
cursor.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 7 – NAVIGATION
7.6
VOR INFORMATION
7.7
USER WAYPOINT INFORMATION
PAGE
See the Flight Planning section for a discussion on creating and modifying user defined waypoints.
7.8
NEAREST AIRPORTS
Figure 7-8 VOR Information Page
Select the VOR Information Page
1.
Turn the large FMS knob to select the WPT page
group.
2.
Turn the small FMS knob to select the fourth
rectangular page icon.
Access Information on a VOR:
Figure 7-9 Nearest Airports Page
Nearest Airport Information on the MFD
Select the Nearest Airports Page
1.
With the VOR Information Page displayed, press
the FMS knob to activate the cursor.
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the large FMS knob to highlight the
desired selection field (identifier, name or closest city).
2.
Turn the small FMS knob to select the first
rectangular page icon.
3.
Turn the FMS knobs to enter an identifier, name
or city and press the ENT key.
1.
4.
Press the FMS knob to remove the flashing
cursor.
Press the APT softkey located at the bottom
of the display. The first airport in the nearest
airports list is highlighted.
2.
Turn the large FMS knob to highlight the
desired airport.
Access Information on a Specific Airport
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
7-5
SECTION 7 – NAVIGATION
Access Runway Information for the
Selected Airport
2.
Press the ENT key to display airport information.
Press the ENT key again (cursor is on ‘BACK’)
to return to the list.
1.
Press the RNWY softkey located at the bottom
of the display.
3.
2.
Turn the small FMS knob to select the desired
runway.
Load an Airport COM Frequency into the
Active COM
1. Turn the large FMS knob to place the cursor
on the desired airport frequency shown in the
window.
Quickly Tune the COM Transceiver to a
Nearby Airport Frequency
1.
Press the FREQ softkey located at the bottom
of the display.
2.
Turn either FMS knob to select the desired
frequency.
3.
Press the ENT key. The selected frequency is
placed in the standby frequency tuning box.
4.
Press the Frequency Toggle key to place the
frequency in the active field.
2.
Press the ENT key and the selected frequency
will become the standby frequency for the
active COM.
3.
Press the Frequency Toggle key to make the
frequency the active frequency.
7.9
NEAREST INTERSECTIONS
Nearest Airports Information on the PFD
Bearing TO
Distance
Airport Symbol
Identifier
Runway Length
Primary COM Frequency
Figure 7-10 Nearest Airports Window
1.
Press the NRST softkey to display the PFD Nearest Airports Window.
View Information on a Specific Airport in
the List
1.
7-6
Turn the large FMS knob to place the cursor on
the desired airport identifier.
Figure 7-11 Nearest Intersections Page
Select the Nearest Intersections Page
1.
Turn the large FMS knob to select the NRST
page group.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 7 – NAVIGATION
2.
Turn the small FMS knob to select the second
rectangular page icon.
View Information on the Nearest Intersection
1.
2.
Press the FMS knob to activate the cursor.
Turn either FMS knob to select the desired
intersection. Press the ENT key.
7.11 NEAREST VOR
Select the Nearest VOR Page
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the small FMS knob to select the fourth
rectangular page icon.
7.10 NEAREST NDB
Figure 7-13 Nearest VOR Page
Figure 7-12 Nearest NDB Page
Select the Nearest NDB Page
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the small FMS knob to select the third
rectangular page icon.
Access Information on a Specific NDB
1.
Press the FMS knob to activate the cursor.
2.
Turn either FMS knob to select the desired NDB.
Press the ENT key. The remaining information
on the Nearest NDB Page pertains to the
selected NDB.
View Information on the Nearest VOR:
1.
With the Nearest VOR Page selected, press the
VOR softkey.
2.
Turn either FMS knob to select a VOR. Press
the ENT key.
OR Press the MENU key. Select the Select VOR
Window option and press the ENT key. Turn
either FMS knob to select a VOR.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
7-7
SECTION 7 – NAVIGATION
Select and Load a VOR Frequency
1.
With the Nearest VOR Page selected, press the
FREQ softkey to highlight the VOR frequency
for the selected VOR.
2.
Press the ENT key. The selected VOR frequency
is placed in the NAV standby frequency field.
OR Press the MENU key. Select the Select Frequency Window option and press the ENT key.
Press the ENT key again when the frequency
field is highlighted to place the selected VOR
frequency in the NAV standby field.
Select a Nearest User Waypoint
1.
With the Nearest User Waypoint Page selected,
press the FMS knob to activate the cursor.
2.
Press the ENT key to select the Nearest User
Waypoint.
3.
The remaining information on the Nearest User
Waypoint Page pertains to the selected Nearest
User Waypoint.
7.13 NEAREST FREQUENCIES
7.12 NEAREST USER WAYPOINT
Figure 7-15 Nearest Frequencies Page
Select the Nearest Frequencies Page
Figure 7-14 Nearest User Waypoints Page
Select the Nearest User Waypoint Page
7-8
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the small FMS knob to select the fifth
rectangular page icon.
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the small FMS knob to select the sixth
rectangular page icon.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 7 – NAVIGATION
Select and Load the Nearest ARTCC, FSS, or
Weather Frequency
1.
With the Nearest Frequencies Page selected,
press the ARTCC, FSS, or Wx softkey.
2.
Turn the large FMS knob to select the frequency.
3.
Press the ENT key to load the frequency into
the ‘COM’ frequency standby field.
7.14 NEAREST AIRSPACES
displayed.
• If the aircraft is within two nautical miles of an
airspace and the current course takes the aircraft
inside, ‘Ahead < 2 nm’ is displayed.
• If the aircraft is within two nautical miles of an
airspace and the current course will not take the
aircraft inside, ‘Within 2 nm’ is displayed.
• If the aircraft has entered an airspace, ‘Inside’ is
displayed.
View Additional Details for a Listed Airspace
1.
Select the Nearest Airspace Page.
2.
Press the FMS knob to activate the cursor.
3.
Turn the large FMS knob to scroll through the
list, highlighting the desired airspace.
4.
Press the ALERTS softkey and turn either FMS
knob to select the desired airspace.
5.
Press the FMS knob to remove the flashing
cursor.
View and Quickly Load the Frequency for a
Controlling Agency
Figure 7-16 Nearest Airspaces Page
Select the Nearest Airspaces Page
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the small FMS knob to select the seventh
rectangular page icon.
1.
Select the Nearest Airspaces Page.
2.
Press the FREQ softkey and turn either FMS
knob to select the desired frequency. Press the
ENT key to load the frequency into the ‘COM’
frequency standby field.
Airspace Alerts Box
• If the projected course takes the aircraft inside an
airspace within the next ten minutes, ‘Ahead’ is
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
7-9
SECTION 7 – NAVIGATION
This page intentionally left blank.
7-10
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 8 – FLIGHT PLANNING
SECTION 8: FLIGHT PLANNING
8.1
3.
Turn the large FMS knob to highlight the
latitude/longitude field or the Reference Waypoints field, depending on how the waypoint
is to be defined.
4.
Turn the FMS knobs to enter the position
coordinates or the radial and distance from
the reference waypoint.
5.
Press the ENT key to accept the new waypoint.
6.
Press the FMS knob to remove the flashing
cursor.
USER DEFINED WAYPOINTS
Create User Waypoints from the Navigation
Map Page
1.
With the Navigation Map Page displayed, push
the joystick to activate the panning function.
The target pointer is displayed at the present
aircraft position.
2.
After placing the pointer at the desired position, press the ENT key. The User Waypoint
Information Page is now displayed with the
captured position.
3.
Turn the FMS knobs to select a waypoint
name.
4.
With the User Waypoint Information Page
displayed, press the FMS knob to activate the
cursor.
Press the ENT key to accept the selected
name. The first reference waypoint field is
highlighted.
5.
Turn the FMS knobs to enter a name for the new
waypoint and press the ENT key. The message
‘Are you sure you want to create the new user
waypoint’ is displayed. With ‘YES’ highlighted,
press the ENT key.
If desired, turn the FMS knobs to enter the
identifier of the reference waypoint and the
radial and distance to the reference waypoint.
Press the ENT key to accept.
6.
Press the FMS knob to remove the flashing
cursor.
Figure 8-1 User WPT Information Page
Select the User WPT Information Page
1.
Turn the large FMS knob to select the NRST
page group.
2.
Turn the small FMS knob to select the fifth
rectangular page icon.
Create a New User Waypoint
1.
2.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
8-1
SECTION 8 – FLIGHT PLANNING
Modify a User Waypoint
1.
With the User Waypoint Information Page
displayed, press the FMS knob to activate the
cursor.
2.
Turn the large FMS knob to move the cursor to
the desired field and turn the small FMS knob
to make changes.
3.
Press the ENT key to accept the changes.
4.
Press the FMS knob to remove the flashing
cursor.
Figure 8-3 Active Flight Plan Window on the PFD
8.3
1.
ACTIVATE A STORED FLIGHT PLAN
Press the FPL key and turn the small FMS knob
to display the Flight Plan Catalog Page.
Delete a User Waypoint
1.
Select the User Waypoint Information Page
and press MENU to display the User Waypoint
Information Page Options or press the DELETE
softkey.
2.
Turn the large FMS knob to select ‘Delete User
Waypoint’ and press the ENT key. The message
‘Would you like to delete the user waypoint’
is displayed. With ‘YES’ highlighted, press the
ENT key.
8.2
1.
VIEWING THE ACTIVE FLIGHT PLAN
Press the FPL key.
Figure 8-4 Flight Plan Catalog Page
2.
Press the FMS knob to activate the cursor.
3.
Turn the large FMS knob to highlight the desired
flight plan and press the ACTIVE softkey.
4.
With OK highlighted, press the ENT key to
activate the flight plan. To cancel the flight
plan activation, turn the large FMS knob to
highlight ‘CANCEL’ and press the ENT key.
8.4
1.
Figure 8-2 Active Flight Plan Page on the MFD
8-2
ACTIVATE A FLIGHT PLAN LEG
From the Active Flight Plan Page, press the FMS
knob to activate the cursor and turn the large
FMS knob to highlight the desired destination
waypoint.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 8 – FLIGHT PLANNING
2.
Press the ACT LEG softkey (using MFD only).
OR
3.
4.
Press the MENU key, select the ‘Activate Leg’
option from the page menu and press the ENT
key. This step must be used when activating a
leg from the PFD.
With ‘Activate’ highlighted, press the ENT
key.
8.6
INVERT ACTIVE FLIGHT PLAN
1.
From the Active Flight Plan Page, press the
MENU key to display the Page Menu.
2.
Turn the large FMS knob to highlight ‘Invert
Flight Plan’ and press the ENT key. The original flight plan remains intact in its flight plan
catalog storage location.
3.
With ‘OK’ highlighted, press the ENT key to
invert the flight plan.
Figure 8-5 Activate Flight Plan Leg Confirmation
8.5
STOP NAVIGATING A FLIGHT PLAN
1.
Press the FPL key and turn the small FMS knob
to display the Active Flight Plan Page.
2.
Press the ENT key to display the Page Menu
window.
Figure 8-8 Invert Flight Plan
Figure 8-9 Invert Flight Plan Confirmation
8.7
Figure 8-6 Delete Flight Plan
3.
Turn the large FMS knob to highlight ‘Delete
Flight Plan’ and press the ENT key. With ‘OK’
highlighted, press the ENT key to deactivate
the flight plan. This will not delete the stored
flight plan, only the active flight plan.
CREATE A NEW FLIGHT PLAN
To create a new flight plan using the MFD:
1.
Press the FPL key and turn the small FMS knob
to display the Flight Plan Catalog Page.
2.
Press the NEW softkey to display a blank flight
plan page for the first empty storage location.
Figure 8-7 Delete Flight Plan Confirmation
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
8-3
SECTION 8 – FLIGHT PLANNING
Figure 8-10 Create FPL on MFD
3.
Turn the small FMS knob to display the Waypoint Information Page. Turn the small FMS
knob to enter the first character of the identifier
of the departure waypoint. Turn the large FMS
knob to move the cursor to the next character
field. Repeat using the FMS knobs until the
desired identifier has been entered.
1.
Press the FPL key and press the small FMS knob
to activate the cursor.
2.
Turn the small FMS knob to enter the first
character of the flight plan starting identifier.
3.
Turn the large FMS knob to move the cursor to
the next character field.
4.
Turn the small FMS knob to enter the next character. Continue this process until the desired
identifier is entered.
5.
Press the ENT key and the cursor is now ready
for entering of the next flight plan waypoint.
6.
Repeat steps 2 through 5 to enter the identifier
for each additional flight plan waypoint.
7.
Once all waypoints have been entered, press
the FMS knob to return to the Active Flight Plan
Window.
Figure 8-11 Waypoint Info Window
4.
Press the ENT key.
5.
Repeat step number 3 to enter the identifier
for each additional flight plan waypoint.
6.
When all waypoints have been entered, press
the FMS knob to return to the Flight Plan
Catalog Page. The new flight plan is now in
the list.
Create a new flight plan using the PFD
NOTE: A flight plan cannot be entered using the
PFD if another flight plan is active.
NOTE: After the first leg is entered (using the
PFD only), it is immediately activated.
8-4
Figure 8-12 Creating Flight Plan on the PFD
8.8
LOAD A DEPARTURE
See the Procedures section for a discussion on loading
and activating departure procedures.
8.9
LOAD AN ARRIVAL
See the Procedures section for a discussion on loading
and activating arrival procedures.
8.10 LOAD AN APPROACH
See the Procedures section for a discussion on loading
and activating approach procedures.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 8 – FLIGHT PLANNING
8.11 REMOVE A DEPARTURE, ARRIVAL,
OR APPROACH FROM A FLIGHT PLAN
1.
2.
3.
With the Active or Stored Flight Plan Page displayed, press the small FMS knob to activate
the cursor.
Turn the large FMS knob to highlight the title
for the approach, departure or arrival to be
deleted. Titles appear in white directly above
the procedure’s waypoints.
Press the CLR key to display a confirmation
window. With ‘OK’ highlighted, press the ENT
key to remove the selected procedure.
8.12 STORE A FLIGHT PLAN
1.
From the Flight Plan Page, press the FMS knob
to activate the cursor.
2.
Turn the large FMS knob to highlight the
desired flight plan and press the MENU key to
display the Flight Plan Page options.
3.
Turn the large FMS knob to highlight ‘Store
Flight Plan’ and press the ENT key.
4.
With ‘OK’ highlighted, press the ENT key to
store the flight plan.
4.
Turn the FMS knobs to make the desired
changes, then press the ENT key.
5.
Press the FMS knob to return to the Flight Plan
Catalog Page.
8.14 DELETE A WAYPOINT FROM THE
FLIGHT PLAN
1.
Press the FPL key and turn the small FMS knob
to display the Flight Plan Catalog Page.
2.
Press the FMS knob to activate the cursor.
3.
Turn the large FMS knob to highlight the
desired flight plan and press the ENT key.
4.
Turn the large FMS knob to select the waypoint
to be deleted and press the CLR key to display a
‘REMOVE WAYPOINT’ confirmation window.
5.
With ‘OK’ highlighted, press the ENT key to
remove the waypoint. To cancel the delete
request, turn the large FMS knob to highlight
‘CANCEL’ and press the ENT key.
6.
Once all changes have been made, press the
FMS knob to return to the Flight Plan Page.
Figure 8-14 Remove Waypoint Confirmation
Figure 8-13 Store Flight Plan Confirmation
8.13 EDIT A STORED FLIGHT PLAN
8.15 INVERT AND ACTIVATE A STORED
FLIGHT PLAN
1.
Press the FPL key and turn the small FMS knob
to display the Flight Plan Catalog Page.
1.
From the Flight Plan Catalog Page, press the
FMS knob to activate the cursor.
2.
Press the FMS knob to activate the cursor.
2.
3.
Turn the large FMS knob to highlight the
desired flight plan and press the ENT key.
Turn the large FMS knob to highlight the
desired flight plan and press the MENU key to
display the Page Menu options.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
8-5
SECTION 8 – FLIGHT PLANNING
3.
4.
Turn the large FMS knob to highlight ‘Invert
Flight Plan’ and press the ENT key. The original flight plan remains intact in its flight plan
catalog storage location.
2.
Press the MENU key to display the Flight Plan
Catalog options.
3.
Turn the large FMS knob to highlight ‘Delete
Flight Plan’ and press the ENT key.
With ‘OK’ highlighted, press the ENT key to
invert the flight plan.
4.
A ‘Delete flight plan?’ confirmation window
is displayed. With ‘OK’ highlighted, press the
ENT key to delete the flight plan. To cancel,
turn the large FMS knob to highlight ‘CANCEL’
and press the ENT key.
8.18 GRAPHICAL FLIGHT PLAN CREATION
Figure 8-15 Invert Flight Plan
1.
Press the FPL key to display the Active Flight
Plan Page.
2.
Press the Joystick to activate the map pointer.
Use the Joystick to move the pointer to the
desired point on the map to be inserted as a
waypoint in the flight plan.
3.
Press the LD WPT softkey. The selected waypoint will be inserted at the end of the flight
plan.
4.
If the selected waypoint is to be placed elsewhere in the flight plan, press the FMS knob
to activate the cursor. Waypoints are inserted
ABOVE the cursor.
5.
After placing the cursor at the desired point
in the list of waypoints, press the LD WPT softkey.
8.16 COPY A FLIGHT PLAN
1.
From the Flight Plan Catalog press the FMS
knob to activate the cursor, turn the large FMS
knob to highlight the flight plan to be copied,
then press the MENU key to display the Flight
Plan Catalog Options.
2.
Turn the large FMS knob to highlight ‘Copy
Flight Plan #’ and press the ENT key.
3.
A ‘Copy to flight plan?’ confirmation window
is displayed. With ‘OK’ highlighted, press the
ENT key to copy the flight plan. To cancel, turn
the large FMS knob to highlight ‘CANCEL’ and
press the ENT key.
8.17 DELETE A FLIGHT PLAN
1.
8-6
From the Flight Plan Catalog Page, press the
FMS knob to activate the cursor, turn the large
FMS knob to highlight the flight plan to be
deleted.
8.19 TRIP PLANNING
1.
Turn the large FMS knob to select the AUX page
group.
2.
Turn the small FMS knob to select the first
rectangular page icon.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 8 – FLIGHT PLANNING
3.
The current page mode is displayed at the
top of the page: ‘AUTOMATIC’ or ‘MANUAL’.
To change the page mode, press the AUTO or
MANUAL softkey.
Figure 8-16 Trip Planning Page
4.
5.
For Direct-to planning, press the WPTS softkey
and verify that the ‘from’ waypoint field indicates P.POS (present position). If necessary,
press the MENU key and select ‘Set WPT to
Present Position’ to display P.POS. Press the
ENT key and the flashing cursor moves to the
‘to’ waypoint field. Turn the FMS knobs to enter
the identifier of the ‘to’ waypoint and press the
ENT key to accept the waypoint. OR,
For point-to-point planning, turn the FMS knobs
to enter the identifier of the ‘from’ waypoint.
Once the waypoints identifier is entered, press
the ENT key to accept the waypoint. The
flashing cursor moves to the ‘to’ waypoint.
Again, turn the FMS knobs to enter the identifier of the ‘to’ waypoint and press the ENT key
to accept the waypoint.
6.
For flight plan leg planning, press the FPL
softkey (at the bottom of the display) and turn
the small FMS knob to select the desired flight
plan (already stored in memory), by number.
Turn the large FMS knob to highlight the ‘LEG’
field and turn the small FMS knob to select the
desired leg of the flight plan, or select ‘CUM’
to apply trip planning calculations to the entire
flight plan.
7.
Turn the large FMS knob to highlight the departure time (DEP TIME) field.
8.
Turn the FMS knobs to enter the departure time.
Press the ENT key when finished. (Departure
time may be entered in local or UTC time,
depending upon unit settings).
9.
Turn the FMS knobs to enter the fuel flow.
Press the ENT key when finished. Note that in
automatic page mode, fuel flow is provided by
the system.
10. The flashing cursor moves to the fuel on board
field. Turn the FMS knobs to modify the fuel on
board. Press the ENT key when finished. Note
that in automatic mode this is provided by the
system.
11. The flashing cursor moves to the calibrated
airspeed field. Turn the FMS knobs to enter an
calibrated airspeed. Press the ENT key when
finished.
OR,
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
8-7
SECTION 8 – FLIGHT PLANNING
This page intentionally left blank.
8-8
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 9 – PROCEDURES
SECTION 9: PROCEDURES
9.1
ARRIVALS AND DEPARTURES
Load and Activate a Departure Procedure
1.
With the Navigation Map Page displayed, press
the FPL key.
2.
Press the LD DP softkey. If a flight plan is active,
the departure airport will be displayed as the
default. A list of available departures is also
displayed.
3.
If no flight plan is active, use the FMS knobs to
enter the identifier of the desired airport. Press
the ENT key.
4.
Turn the large FMS knob to highlight the Departure field. Turn the small FMS knob to display
a list of available departures.
5.
Turn either FMS knob to select the desired
departure and press the ENT key.
Figure 9-1 Select Departure
6.
A list of runways may be displayed for the
departure. Turn either FMS knob to select the
desired runway and press the ENT key.
7.
A list of available transitions is displayed for the
departure. Turn either FMS knob to highlight
the desired transition waypoint and press the
ENT key.
Figure 9-2 Select Departure Transition
8.
With ‘LOAD?’ highlighted, press the ENT key.
The departure will be active when the flight
plan is active.
Load and Activate An Arrival Procedure
1.
With the Navigation Map Page displayed, press
the FPL key.
2.
Press the LD STAR softkey. If a flight plan is
active, the destination airport will be displayed
as the default. A list of available arrivals is also
displayed.
3.
If no flight plan is active, use the FMS knobs to
enter the identifier of the desired airport. Press
the ENT key.
4.
Turn the large FMS knob to highlight the Arrival
field. Turn the small FMS knob to display a list
of available arrivals.
5.
Turn either FMS knob to select the desired
arrival and press the ENT key.
Figure 9-3 Select Arrival
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
9-1
SECTION 9 – PROCEDURES
6.
A second window is displayed listing available
transitions for the arrival. Turn either FMS knob
to highlight the desired transition waypoint and
press the ENT key.
9.2
Load and/or Activate an Approach Procedure
1.
With the Navigation Map Page displayed, press
the FPL key.
2.
Press the LD APR softkey. If a flight plan is
active, the destination airport will be displayed
as the default. A list of available approaches
is also displayed.
3.
If no flight plan is active, use the FMS knobs to
enter the identifier of the desired airport. Press
the ENT key.
4.
Turn the large FMS knob to highlight the
Approach field. Turn the small FMS knob to
display a list of available approaches.
Figure 9-4 Select Arrival Transition
7.
A third window is displayed listing the available
runways. Turn either FMS knob to select the
desired runway and press the ENT key.
APPROACHES
Figure 9-5 Select Arrival Runway
8.
9-2
With ‘LOAD?’ highlighted, press the ENT key.
If a flight plan is active, the selected arrival
procedure is inserted after the destination
airport and becomes part of the active flight
plan. If no flight plan is active when the arrival
is loaded, the arrival procedure will become the
active flight plan.
Figure 9-6 Selecting an Approach Procedure
5.
Turn the FMS knobs to highlight the desired
approach. Press the ENT key.
6.
The cursor will move to the TRANSITIONS
field. Turn the large FMS knob to highlight the
desired transition waypoint and press the ENT
key. (The “Vectors” option assumes vectors will
be received to the final course segment of the
approach and will provide navigation guidance
relative to the final approach course.)
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 9 – PROCEDURES
Figure 9-7 Selecting an Approach Transition
7.
Turn the large FMS knob to highlight ‘Activate?’
and press the ENT key to activate the approach.
Selecting ‘Load?’ will add the procedure to the
flight plan without immediately using it for
navigation guidance.
Activate An Approach in the Active Flight Plan
1.
With the Navigation Map Page displayed, press
the PROC key.
2.
Turn the large FMS knob to highlight ‘ACTIVATE
APPROACH’.
3.
Press the ENT key. The approach procedure is
now active.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
9-3
SECTION 9 – PROCEDURES
This page intentionally left blank.
9-4
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 10 – HAZARD
AVOIDANCE
SECTION 10: HAZARD AVOIDANCE
10.2 STORMSCOPE® (OPTIONAL)
WARNING: Use of the Stormscope system for
hazardous thunderstorm penetration is prohibited. Weather information on the G1000 MFD
is approved for weather avoidance only. Refer
to the WX-500 Pilot’s Guide for detailed operation.
10.1 CUSTOMIZING THE HAZARD
DISPLAYS ON THE NAVIGATION MAP
1.
2.
3.
With the Navigation Map Page displayed, press
the MENU key to display the Navigation Map
Page Menu. The cursor flashes on the ‘Map
Setup’ option.
Press the ENT key. The Map Setup Menu is
displayed. Turn the small FMS knob to select
the ‘Weather’ or ‘Traffic’ group to customize
the display of weather features. Select ‘Traffic’
to customize the display of traffic.
Press the small FMS knob to return to the
Navigation Map Page.
Displaying Stormscope Lightning Data on the
Navigation Map Page
1.
Press the MAP softkey.
2.
Press the STRMSCP softkey. Press the STRMSCP
softkey again to remove Stormscope Lightning
Data from the Navigation Map Page.
Figure 10-1 Page Menu
Figure 10-2 Map Setup Menu
Figure 10-4 In-Flight Navigation Map Page Displaying
Stormscope Lightning Data
Figure 10-3 Map Setup Group List
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
10-1
SECTION 10 – HAZARD
AVOIDANCE
At a map range of less than 25 nm, Stormscope lightning data is not displayed, but can still be present. The
presence of Stormscope lightning data is indicated by the
annunciation ‘LTNG < 25 nm’ in the upper right corner.
2.
Turn the small FMS knob until the Stormscope
Page is selected. This is the third rectangular
page icon.
Figure 10-5 Lightning Display Range Annunciation
To select ‘cell’ or ‘strike’ as the Stormscope
lightning mode:
1.
With the Weather Group selected, press the
ENT key. The cursor flashes on ‘STRMSCP
LTNG’.
2.
Turn the large FMS knob to select ‘STRMSCP
MODE’.
3.
Turn either FMS knob to display the ‘Cell/Strike’
window.
4.
Turn either FMS knob to select ‘Cell’ or ‘Strike’.
Press the ENT key.
5.
Push the FMS knob to return to the Navigation
Map Page.
Figure 10-6 Stormscope Page
To change the Stormscope lightning mode
between ‘cell’ and ‘strike’:
1.
Select the Stormscope Page.
2.
Press the MODE softkey. The CELL and STRIKE
softkeys are displayed. Press the CELL softkey
to display ‘CELL’ data or press the STRIKE softkey to display ‘STRIKE’ data. ‘CELL’ or ‘STRIKE’
is displayed in the mode box located in the
upper left corner of the Stormscope Page.
To clear Stormscope lightning data from
the Navigation Map Page:
1.
Press the MENU key (with the Navigation Map
Page displayed).
2.
Turn either FMS knob to highlight the ‘Clear
Lightning Data’ field and press the ENT key.
NOTE: “Cell mode” uses a clustering program to
identify clusters of electrical activity that indicate
cells.
Stormscope Page
1.
Turn the large FMS knob until the Map Page
group is selected.
To change the viewing mode between 360˚
and 120˚:
1.
10-2
Select the Stormscope Page.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 10 – HAZARD
AVOIDANCE
2.
Press the VIEW softkey. The 360 and ARC softkeys are displayed. Press the 360 softkey to
display a 360˚ viewing are or press the ARC
softkey to display a 120˚ viewing area.
Press the CLEAR softkey to remove all Stormscope lightning data from the display.
10.3 XM WEATHER (OPTIONAL)
WARNING: Use of XM weather for hazardous weather penetration is not recommended.
Weather information provided by XM Radio
Service is approved only for weather avoidance,
not penetration.
1.
Press the MAP softkey.
2.
Press the NEXRAD or XM LTNG softkey to display the desired weather. Press the applicable
softkey again to remove weather data from the
Navigation Map Page.
Displaying METAR and TAF information on the
Airport Information Page
To display METAR and TAF text on the Airport Information Page:
1.
Turn the large FMS knob to select the WPT Page
Group.
2.
Turn the small FMS knob to select the Airport
Information Page.
3.
Press the WX softkey to display METAR and TAF
text (METAR and TAF information is updated
every 12 minutes).
METAR
Text
TAF
Text
WX
Softkey
Figure 10-8 METAR and TAF Text Displayed on the
Airport (Weather) Information Page
Figure 10-7 Navigation Map Page Displaying NEXRAD Weather
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
10-3
SECTION 10 – HAZARD
AVOIDANCE
Displaying Weather on the Weather Data Link
Page
To select the Weather Data Link Page:
1.
Turn the large FMS knob to select the Map Page
Group.
2.
Turn the small FMS knob to select the fourth
rectangular page icon.
3.
Press the available softkeys to select the desired
XM weather product.
4.
Press the LEGEND softkey to view the legends
for the selected products. If necessary, turn the
FMS knobs to scroll through the list. Press the
small FMS knob or the ENT softkey to return to
the map.
NEXRAD Limitations
Certain limitations exist regarding the NEXRAD radar
displays. Some, but not all, are listed here:
• NEXRAD base reflectivity does not provide sufficient information to determine cloud layers or
precipitation characteristics (hail vs. rain, etc).
• An individual NEXRAD site cannot depict high altitude storms at close ranges, and has no information
about storms directly over the site.
• The resolution of displayed NEXRAD data is 2 kilometers. Therefore, when zoomed in on the display,
each square block is 2 kilometers. The intensity
level reflected by the square will be the highest level
sampled within the 2 kilometer square area.
ECHO TOP – press the ECHO TOP softkey to show
the location, elevation, and direction the highest radar echo. This may not indicate the top of
a storm or clouds, only the highest radar return
echo. ECHO TOPS cannot be displayed along
with NEXRAD and CLOUD TOPS. When ECHO
TOPS is activated, NEXRAD and CLOUD TOPS
are removed. Refer to the Legend for a description of the ECHO TOPS coding. The display is
updated every 7.5 minutes.
CLD TOP – press the CLD TOP softkey to show the
cloud top altitude determined from satellite imagery.
The display is updated every 15 minutes.
Figure 10-9 Weather Data Link Page
NEXRAD – press the NEXRAD softkey to show
NEXRAD weather and radar coverage information.
Areas where radar coverage is not available will be
shown in grayish-purple. The display is updated
every five minutes.
10-4
LTNG – pressing the LTNG softkey shows the location
of cloud-to-ground lightning strikes. The display is
updated every five minutes.
NOTE: Strikes depicted represent cloud to ground
strikes within a 2 km radius of the actual strike
location. Therefore, the exact location of the
strike is not displayed.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 10 – HAZARD
AVOIDANCE
CELL MOV – pressing the CELL MOV softkey shows
storm cell movement by displaying an arrow. pointing in the direction of predicted movement. The
display is updated every 12 minutes.
SIG/AIR – pressing the SIG/AIR softkey shows
SIGMET and AIRMET information. The display is
updated every 12 minutes.
METAR – press the METAR softkey to graphically display METARs. METARS are shown as colored flags
at airports providing METAR reports. The display
is updated every 12 minutes.
MORE WX – press the MORE WX softkey to display
the following group of softkeys for additional
weather control:
SFC – pressing the SFC softkey for Surface Analysis
shows current or forecast conditions. Forecasts
are available for intervals of Current, 12, 24, 36,
and 48 hours. Press the softkey corresponding
to the desired forecast. The closest city forecast
information is displayed in the legend. The display is updated every 12 minutes.
FRZ LVL – press the FRZ LVL softkey to display
contour lines for freezing levels. The display is
updated every 12 minutes.
WIND – press the WIND softkey to show wind
speed and direction at a selected altitude from
the ground up to 42,000 feet in 3,000 foot increments. After pressing the WIND softkey, press
the softkey corresponding to the desired winds
aloft altitude. The display is updated every 12
minutes.
COUNTY – pressing the COUNTY softkey provides
specific public awareness and protection weather
warnings for Tornado, Severe Thunderstorm,
and Flood conditions provided by the National
Weather Service (NWS). The display is updated
every 5 minutes.
CYCLONE – pressing the CYCLONE softkey shows
the current location of cyclones (hurricanes and
tropical storms) and their projected track at various time intervals. The display is updated every
12 minutes.
Map Panning Information – Weather Data Link
Page
1.
Push in the joystick to display the panning
arrow.
2.
Move the joystick to place the panning arrow
on AIRMETs, TFRs, METARs, or SIGMETs. Press
the ENT key to display pertinent information
for the selected product.
Note that pressing the ENT key when panning over an AIRMET or a SIGMET displays an
information box that displays the text of the
report. Panning over an airport with METAR
information does not display more information
but allows the user to press the ENT key and
select that Airport’s Information Page to display
the text of the report. Pressing the ENT key
when panning over a TFR displays TFR specific
information.
Weather Product Symbols
Figure 10-10 depicts the symbol for each weather
product (read from left to right) . When a weather product is active, the product symbol is displayed in the lower
right of the screen.
• NEXRAD
• Cloud Top/Echo Top
• XM Lightning
• Cell Movement
• SIGMETs/AIRMETs
• METARs
• City Forecast
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
10-5
SECTION 10 – HAZARD
AVOIDANCE
•
•
•
•
•
Surface Analysis
Freezing Levels
Winds Aloft
County Warnings
Cyclone Warnings
Echo Top (Cloud Top and Echo Top Mutually Exclusive)
Figure 10-10 Weather Product Symbols
Weather Product Age
The age for each of the enabled products is displayed
on the right side of the display. Times are based on Zulu
time when the data was assembled on the ground, not the
time the data was received by the FIS sensor. When the age
of a weather product has exceeded half of the expiration
time, the product time will change from light blue to amber
in color.
10-6
Weather Product
SIGMETs/AIRMETs
City Forecasts
County Warnings
Cyclone Warnings
Echo Tops
Freezing Levels
METARs
Lightning
NEXRAD
Radar Coverage
Cell Movement
Surface Analysis
TFRs
Winds Aloft
TAFs
Clouds Tops
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Expires After
(minutes)
60
60
60
60
30
60
90
30
30
30
30
60
60
90
60
60
SECTION 10 – HAZARD
AVOIDANCE
10.4 TRAFFIC INFORMATION SERVICE (TIS)
Traffic Advisory, aircraft is 400’ above & Traffic out of
Traffic Mode descending, moving in the direction of the line
range
NOTE: If the G1000 is configured to use the
optional Skywatch Traffic Advisory System, TIS
will not be available for use.
NOTE: Traffic Information Service (TIS) is only
available when the aircraft is within the service
volume of a TIS capable terminal radar site.
Displaying Traffic on the Traffic Map Page
1.
Turn the large FMS knob to select the Map Page
Group.
2.
Turn the small FMS knob to select the second
rectangular page icon.
3.
4.
5.
Press the OPERATE softkey to begin displaying
traffic. ‘TIS OPERATIING’ is displayed in the
Traffic mode field.
Press the STANDBY softkey to place the system
in the Standby mode. ‘TIS STANDBY’ will be
displayed in the Traffic mode field.
Rotate the Joystick clockwise to display a larger
area or rotate counter-clockwise to display a
smaller area.
If data is not received for a period longer than 6 seconds, the age of the present data will be displayed in the
lower left of of the screen along with the annuciation that
the system has entered Coast mode. The system will
maintain the traffic display (up to 60 seconds) until the
next data reception. If no data is received after 60 seconds, traffic will be removed from the display.
Last data update Proximity Traffic at same
Traffic 1600’ above &
is older than 6 altitude, level flight & moving climbing, moving in the
sec. resulting in
in the direction of the line
direction of the line
Coast mode
Figure 10-11 Traffic Map Page
Displaying Traffic on the Navigation Map
1.
Ensure TIS is operating. With the Navigation
Map displayed, press the MAP softkey.
2.
Press the TRAFFIC softkey. Traffic will now be
displayed on the map.
TIS Audio Alert
When a Traffic Advisory (TA) is displayed, an audio
alert “Traffic” is given.
“Traffic Not Available” will be heard whenever TIS service becomes unavailable.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
10-7
SECTION 10 – HAZARD
AVOIDANCE
10.5 SKYWATCH TRAFFIC ADVISORY
SYSTEM (TAS)(OPTIONAL)
Traffic Advisory,
aircraft is 400’ below
Traffic Mode Altitude Mode
& climbing
Traffic, Out of
Range
Refer to the SkyWatch pilot’s guide for a detailed discussion of the SkyWatch system.
Displaying Traffic on the Traffic Map Page
1.
Turn the large FMS knob to select the Map Page
Group.
2.
Turn the small FMS knob to select the second
rectangular page icon.
3.
Press the OPERATE softkey to begin displaying
traffic. ‘TAS OPERATING’ is displayed in the
Traffic mode field.
4.
Press the ALT MODE softkey to change the
altitude volume. Select the desired altitude
volume by pressing the the BELOW, NORMAL,
ABOVE, or UREST (unrestricted) softkey. The
selection is displayed in the Altitude mode
field.
5.
6.
10-8
Press the STANDBY softkey to place the system
in the Standby mode. ‘TAS STANDBY’ will be
displayed in the Traffic mode field.
Rotate the Joystick clockwise to display a larger
area or rotate counter-clockwise to display a
smaller area.
“Non-Bearing” Traffic (system
is unable to determine bearing),
distance is 8.0 nm, 1190’ above
and descending
Proximity Traffic,
1000’ above &
descending
Figure 10-12 Traffic Map Page
Displaying Traffic on the Navigation Map
1.
Ensure the SkyWatch system is operating. With
the Navigation Map displayed, press the MAP
softkey.
2.
Press the TRAFFIC softkey. Traffic will now be
displayed on the map.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 10 – HAZARD
AVOIDANCE
4.
Traffic Advisory
Non-Bearing
Traffic Off Scale
Traffic Advisories
Banner
Rotate the Joystick clockwise to display a larger
area or rotate counter-clockwise to display a
smaller area.
Non-Threat
Traffic
Figure 10-13 TAS Traffic on Navigation Map
10.6 TERRAIN AND OBSTACLE PROXIMITY
NOTE: Terrain data is not displayed when the
aircraft latitude is greater than 75 degrees (north
or south).
Displaying Terrain and Obstacles on the Terrain
Proximity Page
1.
Turn the large FMS knob to select the Map Page
Group.
2.
Turn the small FMS knob to select the last
rectangular page icon.
3.
If desired, press the VIEW softkey to access the
ARC and 360 softkeys. When the ARC softkey
is pressed, a radar-like 120° view is displayed.
Press the 360 softkey to return to the 360°
default display.
Figure 10-14 Terrain Proximity Page
Color
RED
YELLOW
Indication
WARNING: At or within 100’ below the
current aircraft altitude.
CAUTION: Between 100’ and 1000’ below
the current aircraft altitude.
Aircraft Altitude
100' Threshold
1000' AGL
Displaying Terrain and Obstacles on the
Navigation Map
1.
With the Navigation Map displayed, press the
MAP softkey.
2.
Press the TERRAIN softkey. Terrain and obstacle
proximity will now be displayed on the map.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
10-9
SECTION 10 – HAZARD
AVOIDANCE
Unlighted Obstacle
(Height is less than
1000’ AGL)
Lighted Obstacle
(Height is less than
1000’ AGL)
Unlighted Obstacle
(Height is greater than
1000’ AGL)
Lighted Obstacle
(Height is greater than
1000’ AGL)
Figure 10-15 Obstacle Symbols
Maximum
elevation of
topography presently
displayed on-screen
Minimum
elevation of
topography presently
displayed on-screen
Aircraft altitude
Range of
topography elevation presently displayed on-screen
Ground elevation
at present aircraft
position
Figure 10-16 Topography Scale
10-10
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 11 – ABNORMAL
OPERATION
SECTION 11: ABNORMAL
OPERATION
11.1 REVERSIONARY MODE
Should a system detected failure occur in either display, the G1000 automatically enters reversionary mode.
In reversionary mode, critical flight instrumentation is
combined with engine instrumentation on the remaining
display. Minimal navigation capability is available on the
reversionary mode display.
Normal PFD Display
Reversionary display mode can also be manually activated by the pilot if the system fails to detect a display
problem. The reversionary mode is activated manually
by pressing the red DISPLAY BACKUP button on the
bottom of the audio panel (GMA 1347). Pressing the red
DISPLAY BACKUP button again deactivates reversionary mode.
NOTE: The Mooney M20M/M20R Airplane Flight
Manual and Flight Manual Supplement always
takes precedence over the information found in
this section.
Normal MFD Display
MFD in Reversionary Mode
Figure 11-1 G1000 Reversionary Mode: Failed PFD
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
11-1
SECTION 11 – ABNORMAL
OPERATION
11.2 ABNORMAL COM OPERATION
When a COM tuning failure is detected by the system,
the emergency frequency (121.500 MHz) is automatically
loaded into the active frequency field of the COM radio
for which the tuning failure was detected. In the event of
a dual display failure, the emergency frequency (121.500
MHz) automatically becomes the active frequency to the
pilot through the pilot headset.
11.3 UNUSUAL ATTITUDES
The PFD will ‘declutter’ when the aircraft enters an unusual attitude. Only the basic primary functions will be
displayed in these situations.
Red extreme pitch warning chevrons pointing toward
the horizon are displayed starting at 50 degrees above and
30 degrees below the horizon line.
Figure 11-2 Extreme Pitch Indication
11-2
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 12 – ANNUNCIATIONS
& ALERTS
SECTION 12: ANNUNCIATIONS &
ALERTS
• Audio Alerting System: The G1000 system issues
audio alert tones when specific system conditions
are met. See the Alert Levels Definitions section for
more information.
NOTE: The Airplane Flight Manual Supplement
supersedes information found in this document.
The G1000 Alerting System conveys alerts to the pilot
using a combination of the following items:
• Alerts Window: The Alerts window displays alert
text messages. Up to 64 prioritized alerts can be displayed in the Alerts window. Pressing the ALERTS
softkey displays the Alerts window. Pressing the
ALERTS softkey again removes the Alerts window
from the display. When the Alerts window is displayed, the pilot may use the large FMS knob to
scroll through the alert list. Higher priority alerts are
displayed at the top of the window. Lower priority
alerts are displayed at the bottom of the window.
• ALERTS Softkey Annunciation: When the Alerting System issues an alert, the ALERTS softkey is
used as a flashing annunciation to accompany an
alert. During the alert, the ALERTS softkey assumes
a new label consistent with alert level (WARNING,
CAUTION, or ADVISORY). Pressing the softkey
annunciation acknowledges that the pilot is aware
of the alert. The softkey then returns to the previous ALERTS label. The pilot can then press the
ALERTS softkey again to view alert text messages.
System
Annunciation
Red ‘X’
Alerts Window
Figure 12-1 G1000 Alerting System
ALERTS Softkey
Annunciation
• System Annunciations: Typically, a large red ‘X’
appears in a window when a related LRU fails or
detects invalid data.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-1
SECTION 12 – ANNUNCIATIONS
& ALERTS
12.1 ALERT LEVEL DEFINITIONS
12.2 M20M/M20R AIRCRAFT ALERTS
The G1000 Alerting System, as installed in Mooney
M20M and M20R aircraft, uses one alert level.
The following alerts are configured specifically for
the Mooney M20M and M20R aircraft. See the Mooney
M20M/M20R Flight Manual Supplement for information
regarding pilot responses.
• MESSAGE ADVISORY: This level of alert provides
general information to the pilot. A message advisory
alert does not issue annunciations in the Annunciation window. Instead, message advisory alerts only
issue a flashing ADVISORY softkey annunciation,
as shown in Figure 12-2. Pressing the ADVISORY
softkey acknowledges the presence of the message
advisory alert and displays the alert text message in
the Alerts window.
Voice Alerts
Voice Alert
“Check Gear”
“Stall”
Figure 12-2 ADVISORY Softkey
Annunciation
12-2
Alert Trigger
Played when landing gear
remain in the ‘Up’ position,
and the pilot retards the
throttle to within 1/4” of
Idle.
Played when a stall is
detected.
Message Advisory Alerts
Alerts Window Message
PFD FAN FAIL – The cooling fan for
the PFD is inoperative.
MFD FAN FAIL – The cooling fan for
the MFD is inoperative.
GIA FAN FAIL – The cooling fan for
the GIAs is inoperative.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Audio Alert
None
None
None
SECTION 12 – ANNUNCIATIONS
& ALERTS
12.3 G1000 SYSTEM ANNUNCIATIONS
When an LRU or an LRU function fails, a large red
‘X’ is typically displayed on windows associated with the
failed data. The following section describes various system annunciations. Refer to the Aircraft Flight Manual for
additional information regarding pilot responses to these
annunciations.
NOTE: Upon power-up of the G1000 system,
certain windows remain invalid as G1000 equipment begins to initialize. All windows should
be operational within one minute of power-up.
Should any window continue to remain flagged,
the G1000 system should be serviced by a
Garmin-authorized repair facility.
System Annunciation
Comment
Attitude and Heading Reference System is aligning.
Display system is not receiving attitude information from the AHRS.
Display system is not receiving airspeed input from air data computer.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-3
SECTION 12 – ANNUNCIATIONS
& ALERTS
System Annunciation
Comment
Display is not receiving altitude input from the air data computer.
Display is not receiving vertical speed input from the air data computer.
Display is not receiving valid heading input from AHRS.
GPS information is either not present or is invalid for navigation use.
Note that AHRS utilizes GPS inputs during normal operation. AHRS operation
may be degraded if GPS signals are not present (see POH).
Display is not receiving valid transponder information.
Other Various Red X Indications
12-4
A red ‘X’ through any other display field, such as engine instrumentation
fields, indicates that the field is not receiving valid data.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 12 – ANNUNCIATIONS
& ALERTS
Voice Alerts
Voice Alert
“Traffic”
“Traffic Not Available”
“Traffic, Traffic”
“Traffic Advisory System Test Passed”
“Traffic Advisory System Test Failed”
Alert Trigger
Played when a Traffic Advisory (TA) is issued (TIS system).
Played when the traffic system fails or cannot communicate (TIS system).
Played when a Traffic Advisory (TA) is issued (Skywatch TAS system).
Played when the TAS system passes a pilot-initiated self test.
Played when the TAS system fails a pilot-initiated self test.
Audio Alerts
Audio Alert
Altitude Alert Chime
Alert Trigger
When aircraft altitude reaches the reference altitude threshold (+/- 1,000 ft of reference altitude).
When aircraft altitude reaches or goes beyond the reference altitude deviation limit (+/-200 ft of reference altitude).
When aircraft elevation reaches the reference altitude.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-5
SECTION 12 – ANNUNCIATIONS
& ALERTS
A red ‘X’ may be the result of an LRU or an LRU function failure. The Figure 12-3 illustrates all possible flags
and the responsible LRUs.
12.4 G1000 SYSTEM MESSAGE
ADVISORIES
This section describes various G1000 system message
advisories. Certain messages are issued due to an LRU or an
LRU function failure. Such messages are normally accompanied by a corresponding red ‘X’ annunciation as shown
previously in the G1000 System Annunciation section.
NOTE: This Section provides information regarding G1000 message advisories that may be displayed by the system. Knowledge of the aircraft,
systems, flight conditions, and other existing
operational priorities must be considered when
responding to a message. Always use sound
pilot judgment. The Aircraft Flight Manual takes
precedence over any conflicting guidance found
in this section.
GIA 63 Integrated
Avionics Units
GIA 63 Integrated
Avionics Units
GDC 74A Air Data
Computer
GRS 77 AHRS
OR
GMU 44
Magnetometer
GEA 71 Engine
Airframe Unit
OR
GIA 63 Integrated
Avionics Unit
GIA 63 Integrated
Avionics Units
GDC 74A Air Data
Computer
Figure 12-3 G1000 System Failure Annunciations
12-6
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
GTX 33 Transponder
OR
GIA 63 Integrated
Avionics Units
SECTION 12 – ANNUNCIATIONS
& ALERTS
MFD & PFD Message Advisories
Message
DATA LOST – Pilot stored data was
lost. Recheck settings.
XTALK ERROR – A flight display
crosstalk error has occurred.
PFD1 SERVICE – PFD1 needs service.
Return unit for repair.
MFD1 SERVICE – MFD1 needs
service. Return unit for repair.
PFD1 CONFIG – PFD1 configuration
error. Config service req’d.
MFD1 CONFIG – MFD1 configuration
error. Config service req’d.
SW MISMATCH – GDU software
mismatch. Xtalk is off.
MANIFEST – PFD1 software mismatch.
Communication halted.
MANIFEST – MFD1 software
mismatch. Communication halted.
PFD1 COOLING – PFD1 has poor
cooling. Reducing power usage.
MFD1 COOLING – MFD1 has poor
cooling. Reducing power usage.
PFD1 “KEY” KEYSTK – Key is stuck.
MFD1 “KEY” KEYSTK – Key is stuck.
CNFG MODULE – PFD1 configuration
module is inoperative.
Comments
The pilot profile data was lost. System reverts to default pilot profile and settings.
The pilot may reconfigure the MFD & PFD with preferred settings, if desired.
The MFD and PFD are not communicating with each other. The G1000 system should
be serviced.
The PFD and/or MFD self-test has detected a problem. The G1000 system should be
serviced.
The PFD and/or MFD configuration settings do not match backup configuration
memory. The G1000 system should be serviced.
The MFD and PFD have different software versions installed. The G1000 system
should be serviced.
The PFD and/or MFD has incorrect software installed. The G1000 system should be
serviced.
The PFD and/or MFD is overheating and is reducing power consumption by dimming
the display. If problem persists, the G1000 system should be serviced.
A key is stuck on the PFD and/or MFD bezel. Attempt to free the stuck key by pressing it several times. The G1000 system should be serviced if the problem persists.
The PFD configuration module backup memory has failed. The G1000 system should
be serviced.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-7
SECTION 12 – ANNUNCIATIONS
& ALERTS
Database Message Advisories
Alerts Window Message
Comments
MFD1 DB ERR – MFD1 aviation
database error exists.
The MFD and/or PFD detected a failure in the aviation database. Attempt to reload
the aviation database. If problem persists, the G1000 system should be serviced.
PFD1 DB ERR – PFD1 aviation
database error exists.
MFD1 DB ERR – MFD1 basemap
database error exists.
The MFD and/or PFD detected a failure in the basemap database.
PFD1 DB ERR – PFD1 basemap
database error exists.
MFD1 DB ERR – MFD1 terrain
The MFD and/or PFD detected a failure in the terrain database. Ensure that the terdatabase error exists.
rain card is properly inserted in display. Replace terrain card. If problem persists, The
PFD1 DB ERR – PFD1 terrain database G1000 system should be serviced.
error exists.
DB MISMATCH – Aviation database
The PFD and MFD have different aviation database versions installed. Crossfill is off.
version mismatch. Xtalk is off.
Install correct aviation database version in both displays.
DB MISMATCH – Aviation database
The PFD and MFD have different aviation database types installed (Americas, European, etc.). Crossfill is off. Install correct aviation database type in both displays.
type mismatch. Xtalk is off.
DB MISMATCH – Basemap database
The PFD and MFD have different basemap database versions installed. Crossfill is
version mismatch. Xtalk is off.
off. Install correct basemap database version in both displays.
DB MISMATCH – Terrain database
The PFD and MFD have different terrain database versions installed. Crossfill is off.
version mismatch. Xtalk is off.
Install correct terrain database version in both displays.
DB MISMATCH – Terrain database
The PFD and MFD have different terrain database types installed. Crossfill is off.
type mismatch. Xtalk is off.
Install correct terrain database type in both displays.
DB MISMATCH – Obstacle database
The PFD and MFD have different obstacle database versions installed. Crossfill is off.
version mismatch. Xtalk is off
Install correct obstacle database version in both displays.
12-8
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 12 – ANNUNCIATIONS
& ALERTS
GMA 1347 Message Advisories
Alerts Window Message
GMA1 FAIL – GMA1 is inoperative.
Comments
The audio panel self-test has detected a failure. The audio panel is unavailable. The
G1000 system should be serviced.
GMA1 CONFIG – GMA1 configuration The audio panel configuration settings do not match backup configuration memory.
error. Config service req’d.
The G1000 system should be serviced.
MANIFEST – GMA1 software
The audio panel has incorrect software installed. The G1000 system should be
mismatch. Communication halted.
serviced.
GMA1 SERVICE – GMA1 needs
The audio panel self-test has detected a problem in the unit. Certain audio functions
service. Return unit for repair.
may still be available, and the audio panel may still be usable. The G1000 system
should be serviced when possible.
BACKUP PATH – Audio panel using
The audio panel is using a backup communication path. The G1000 system should
backup data path.
be serviced when possible.
GIA 63 Message Advisories
Alerts Window Message
GIA1 CONFIG – GIA1 configuration
error. Config service req’d.
GIA2 CONFIG – GIA2 configuration
error. Config service req’d.
GIA1 COOLING – GIA1 temperature
too low.
GIA2 COOLING – GIA2 temperature
too low.
GIA1 COOLING – GIA1 over
temperature.
GIA2 COOLING – GIA2 over
temperature.
GIA1 SERVICE – GIA1 needs service.
Return the unit for repair.
GIA2 SERVICE – GIA2 needs service.
Return the unit for repair.
Comments
The GIA1 and/or GIA2 configuration settings do not match backup configuration
memory. The G1000 system should be serviced.
The GIA1 and/or GIA2 temperature is too low to operate correctly. Allow units to
warm up to operating temperature.
The GIA1 and/or GIA2 temperature is too high. If problem persists, the G1000
system should be serviced.
The GIA1 and/or GIA2 self-test has detected a problem in the unit. The G1000
system should be serviced.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-9
SECTION 12 – ANNUNCIATIONS
& ALERTS
GIA 63 Message Advisories (Cont.)
Alerts Window Message
Comments
MANIFEST – GIA1 software mismatch.
Communication halted.
The GIA1 and/or GIA 2 has incorrect software installed. The G1000 system should
MANIFEST – GIA2 software mismatch. be serviced.
Communication halted.
COM1 TEMP – COM1 over temp.
The system has detected an over temperature condition in COM1 and/or COM2. The
Reducing transmitter power.
transmitter will operate at reduced power. If the problem persists, the G1000 system
COM2 TEMP – COM2 over temp.
should be serviced.
Reducing transmitter power.
COM1 SERVICE – COM1 needs
service. Return unit for repair.
The system has detected a failure in COM1 and/or COM2. COM1 and/or COM2 may
still be usable. The G1000 system should be serviced when possible.
COM2 SERVICE – COM2 needs
service. Return unit for repair.
COM1 PTT – COM1 push-to-talk key
The COM1 and/or COM2 external push-to-talk switch is stuck in the enable (or
is stuck.
“pressed”) position. Press the PTT switch again to cycle its operation.
COM2 PTT – COM2 push-to-talk key
If the problem persists, the G1000 system should be serviced.
is stuck.
COM1 RMT XFR – COM1 remote
The COM1 and/or COM2 transfer switch is stuck in the enabled (or “pressed”) positransfer key is stuck.
tion. Press the transfer switch again to cycle its operation. If the problem persists,
COM2 RMT XFR – COM2 remote
the G1000 system should be serviced.
transfer key is stuck.
RAIM UNAVAIL – RAIM is not
GPS satellite coverage is insufficient to perform Receiver Autonomous Integrity
available from FAF to MAP waypoints.
Monitoring (RAIM) from the FAF to the MAP waypoints.
RAIM UNAVAIL – RAIM is not
GPS satellite coverage is insufficient to perform Receiver Autonomous Integrity
available.
Monitoring (RAIM) for the current phase of flight.
POSN ERROR – RAIM has determined When a RAIM position error is detected, GPS is flagged and the system no longer
GPS position is in error.
provides GPS-based guidance.
DGRD GPS ACC – GPS position
GPS position accuracy has been degraded and RAIM is not available.
accuracy degraded & RAIM unavailable.
GPS1 FAIL – GPS1 is inoperative.
A failure has been detected in the GPS1 and/or GPS2 receiver. The receiver is
unavailable. The G1000 system should be serviced.
GPS2 FAIL – GPS2 is inoperative.
12-10
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 12 – ANNUNCIATIONS
& ALERTS
GIA 63 Message Advisories (Cont.)
Alerts Window Message
Comments
GPS1 SERVICE – GPS1 needs service.
Return unit for repair.
A failure has been detected in the GPS1 and/or GPS2 receiver. The receiver may still
GPS2 SERVICE – GPS2 needs service. be available. The G1000 system should be serviced.
Return unit for repair.
NAV1 SERVICE – NAV1 needs service.
Return unit for repair.
A failure has been detected in the NAV1 and/or NAV2 receiver. The receiver may still
NAV2 SERVICE – NAV2 needs service. be available. The G1000 system should be serviced.
Return unit for repair.
NAV1 RMTXFR – NAV1 remote
The remote NAV1 and/or NAV2 transfer switch is stuck in the enabled (or “pressed”)
transfer key is stuck.
state. Press the transfer switch again to cycle its operation. If the problem persists,
NAV2 RMTXFR – NAV2 remote
the G1000 system should be serviced.
transfer key is stuck.
G/S1 FAIL – G/S1 is inoperative.
A failure has been detected in glideslope receiver 1 and/or receiver 2. The G1000
system should be serviced.
G/S2 FAIL – G/S2 is inoperative.
G/S1 SERVICE – G/S1 needs service.
Return unit for repair.
A failure has been detected in glideslope receiver 1 and/or receiver 2. The receiver
may still be available. The G1000 system should be serviced when possible.
G/S2 SERVICE – G/S2 needs service.
Return unit for repair.
GEA 71 Message Advisories
Alerts Window Message
GEA1 CONFIG – GEA1 configuration
error. Config service req’d.
MANIFEST – GEA1 software
mismatch. Communication halted.
BACKUP PATH – EIS using backup
data path.
Comments
The GEA 71 configuration settings do not match those of backup configuration
memory. The G1000 system should be serviced.
The GEA 71 has incorrect software installed. The G1000 system should be serviced.
The GEA 71 is using a backup communication path. The G1000 system should be
serviced when possible.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-11
SECTION 12 – ANNUNCIATIONS
& ALERTS
GTX 33 Message Advisories
Alerts Window Message
XPDR1 CONFIG – XPDR1 config error.
Config service req’d.
MANIFEST – GTX1 software mismatch.
Communication halted.
BACKUP PATH – Transponder using
backup data path.
Comments
The transponder configuration settings do not match those of backup configuration
memory. The G1000 system should be serviced.
The transponder has incorrect software installed. The G1000 system should be
serviced.
The transponder is using a backup communications path. The G1000 system should
be serviced when possible.
GRS 77 Message Advisories
Alerts Window Message
AHRS TAS – AHRS not receiving
airspeed.
AHRS GPS – AHRS using backup GPS
source.
AHRS GPS – AHRS not receiving GPS
information.
AHRS GPS – AHRS not receiving
backup GPS information.
AHRS GPS – AHRS operating
exclusively in no-GPS mode.
MANIFEST – GRS1 software mismatch.
Communication halted.
BACKUP PATH – AHRS using backup
data path.
AHRS SERVICE – AHRS Magnetic-field
model needs update.
GEO LIMITS – Too far North/South, no
magnetic compass.
12-12
Comments
The AHRS is not receiving true airspeed from the air data computer. The AHRS relies
on GPS information to augment the lack of airspeed. The G1000 system should be
serviced.
The AHRS is using the backup GPS path. Primary GPS path has failed. The G1000
system should be serviced when possible.
The AHRS is not receiving any or any useful GPS information. Check AFMS limitations. The G1000 system should be serviced.
The AHRS is not receiving backup GPS information. The G1000 system should be
serviced.
The AHRS is operating exclusively in no-GPS mode. The G1000 system should be
serviced.
The AHRS has incorrect software installed. The G1000 system should be serviced.
The AHRS is using a backup communications data path. The G1000 system should
be serviced when possible.
The AHRS earth magnetic field model is out of date. Update magnetic field model
when practical.
The aircraft is outside geographical limits for approved AHRS operation. Heading is
flagged as invalid.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 12 – ANNUNCIATIONS
& ALERTS
GMU 44 Message Advisories
Alerts Window Message
HDG FAULT – A magnetometer fault
has occurred.
MANIFEST – GMU1 software
mismatch. Communication halted.
Comments
A fault has occurred in the GMU 44. Heading is flagged as invalid. The AHRS uses
GPS for backup mode operation. The G1000 system should be serviced.
The GMU 44 has incorrect software installed. The G1000 system should be serviced.
GDL 69 Message Advisories
Alerts Window Message
GDL69 CONFIG – GDL 69 configuration error. Config service req’d.
GDL69 FAIL – GDL 69 has failed.
Comments
GDL 69 configuration settings do not match those of backup configuration memory.
The G1000 system should be serviced.
A failure has been detected in the GDL 69. The receiver is unavailable. The G1000
system should be serviced
GDC 74A Message Advisories
Alerts Window Message
Comments
GDC1 CONFIG – GDC1 configuration GDC 74A configuration settings do not match those of backup configuration
error. Config service req’d.
memory. The G1000 system should be serviced.
MANIFEST – GDC1 software
The GDC 74A has incorrect software installed. The G1000 system should be
serviced.
mismatch. Communication halted.
BACKUP PATH – Airdata using backup The GDC 74A is using a backup communications data path. The G1000 system
data path.
should be serviced when possible.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-13
SECTION 12 – ANNUNCIATIONS
& ALERTS
Miscellaneous Message Advisories
Alerts Window Message
Comments
FPL WPT LOCK – Flight plan waypoint Upon power-up, the G1000 system detects that a stored flight plan waypoint is
is locked.
locked. This occurs when an aviation database update eliminates an obsolete waypoint. The flight plan cannot find the specified waypoint and flags this message. This
can also occur with user waypoints in a flight plan that is deleted.
Remove the waypoint from the flight plan if it no longer exists in any database,
OR
update the waypoint name/identifier to reflect the new information.
FPL WPT MOVE – Flight plan
The system has detected that a waypoint coordinate has changed due to a new
waypoint moved.
aviation database update. Verify that stored flight plans contain correct waypoint
locations.
TIMER EXPIRD – Timer has expired.
The system notifies the pilot that the timer has expired.
DB CHANGE – Database changed.
This occurs when a stored flight plan contains procedures that have been manually
Verify user modified procedures.
edited. This alert is issued only after an aviation database update. Verify that the
user-modified procedures in stored flight plans are correct and up to date.
FPL TRUNC – Flight plan has been
This occurs when a newly installed aviation database eliminates an obsolete approach or arrival used by a stored flight plan. The obsolete procedure is removed
truncated.
from the flight plan. Update flight plan with current arrival or approach.
APPR VPROF – Approaching VNAV
Aircraft is approaching VNAV profile. Prepare to climb or descend to meet VNAV
profile.
profile.
APPR TRG ALT – Approaching target
Aircraft is approaching target altitude. Prepare to level aircraft.
altitude.
LOCKED FPL – Cannot navigate locked This occurs when the pilot attempts to activate a stored flight plan that contains
flight plan.
locked waypoint. Remove locked waypoint from flight plan. Update flight plan with
current waypoint.
WPT ARRIVAL – Arriving at waypoint
Arriving at waypoint [xxxx], where [xxxx] is the waypoint name.
-[xxxx]
STEEP TURN – Steep turn ahead.
A steep turn is 15 seconds ahead. Prepare to turn.
INSIDE ARSPC – Inside airspace.
The aircraft is inside the airspace.
ARSPC AHEAD – Airspace ahead less Special use airspace is ahead of aircraft. The aircraft will penetrate the airspace
than 10 minutes.
within 10 minutes.
ARSPC NEAR – Airspace near and
Special use airspace is near and ahead of the aircraft position.
ahead.
12-14
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
SECTION 12 – ANNUNCIATIONS
& ALERTS
Miscellaneous Message Advisories (Cont.)
Alerts Window Message
Comments
ARSPC NEAR – Airspace near – less
Special use airspace is within 2 nm of the aircraft position.
than 2 nm.
LEG UNSMOOTH – Flight plan leg will The approaching flight plan waypoints are too close to allow for smooth turns.
not be smooth.
Prepare for steep turns ahead and expect noticeable course deviations.
APPR INACTV – Approach is not
The system notifies the pilot that the loaded approach is not active. Activate apactive.
proach when required.
SLCT AUTOSEQ – Select auto
The system notifies the pilot to select auto-sequence mode. Press the OBS softkey to
sequence mode.
deactivate the OBS mode.
The system notifies the pilot to load the approach frequency for the appropriate NAV
SLCT FREQ – Select appropriate
frequency for approach.
receiver. Select the correct frequency for the approach.
SLCT NAV – Select NAV on CDI for
The system notifies the pilot to set the CDI to the correct NAV receiver. Set the CDI
approach.
to the correct NAV receiver.
NO WGS84 WPT – Non WGS 84
The selected waypoint [xxxx] does not use the WGS 84 datum. Cross-check position
waypoint for navigation -[xxxx]
with alternate navigation sources.
TRAFFIC FAIL – Traffic device has
The traffic information system TIS has failed. The G1000 system should be serviced.
failed.
STRMSCP FAIL – Stormscope has
Stormscope has failed. The G1000 system should be serviced.
failed.
Stormscope is using the backup communication path. The G1000 system should be
BACKUP PATH – Stormscope using
backup path.
serviced when possible.
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
12-15
SECTION 12 – ANNUNCIATIONS
& ALERTS
This page intentionally left blank.
12-16
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
INDEX
A
Abnormal COM operation 11-2
Activate a flight plan 8-2
Active flight plan 8-2
ADF 1-5, 4-3
ADVISORY 12-1
Advisory alerts 12-2
Age 10-6
AHRS 12-12
Aircraft alerts 12-2
AIRMET 10-5
Airport frequency 7-6
Airport information 7-3
Airspace alerts 7-9
Airspeed indicator 2-3
Airspeed trend vector 2-3
Alerting System 12-1
Alerts 12-1
Alert levels 12-2
Altitude reference bug 2-4
Altitude trend vector 2-4
ALT knob 1-3
Approaches 9-2
Approach activation 4-4
Approach markers
Signal augmentation 5-2
Arrivals 9-1
Attitude indicator 2-3
Audio alerting system 12-1
Audio panel 4-3, 5-1
Audio panel controls
ADF 5-2
DME 5-2
NAV1 5-2
NAV2 5-2
Auto-tuning 4-4
Automatic squelch 4-3
B
Barometric setting 2-4
Base reflectivity 10-4
BKSP softkey 4-5
BRG1 2-6
BRG2 2-6
C
Caution 12-1
CDI 2-7, 12-15
Cell 10-2
Cell mode 10-2
Cell movement 10-5
Cloud tops 10-4
CLR key 1-3
Coast mode 10-7
Codes (important) 4-5
Code selection 4-5
CODE softkey 4-5
COM Frequency Window 4-1
COM knob 4-3
Controls 1-2, 4-1
Create a new flight plan 8-3, 8-4
Create a new user waypoint 8-1
Cyclones 10-5
Cylinder select 3-1
CYL SLCT 3-1
D
Departures 9-1
Direct-to 7-1
DME 1-5, 4-4
Dual CDU failure 11-2
E
ECHO TOPS 10-4
Edit a flight plan 8-5
Elevator trim 3-2
Emergency code 4-5
Engine display 3-1
ENGINE softkey 3-1
F
Flaps 3-2
Flight ID 4-5
Flight Plan Catalog 9-1, 9-2
FPL key 1-3
Freezing level 10-5
Frequency toggle key 1-3, 4-3
G
GMA 1347 1-1
H
Heading indication 2-6
Headset(s) 5-2
Hijack code 4-5
Horizontal situation indicator 2-5
HSI 2-5
Hurricanes 10-5
I
ICAO 4-5
ID 4-3
IDENT function 4-5
INTEG 2-7
Interrogations 4-5
K
Key(s) 1-3
L
Lightning 1-4, 1-7, 10-2, 10-3, 10-4
lightning 1-4, 1-7, 10-2, 10-3, 10-4
Load approach 8-4
Load a VOR frequency 7-8
Load departure 8-4
Load the frequency for a controlling
agency 7-9
Load the nearest ARTCC frequency 7-9
Loss of communication code 4-5
M
MAP 7-1
Map panning 10-5
Marker beacon 2-4
messages 12-1
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Index-1
INDEX
Message advisories 12-2, 12-7, 12-9,
12-11, 12-12, 12-14, 12-15
METAR 10-3, 10-5
MFD 1-1, 4-4
Military interceptor operations code
4-5
MKR/MUTE 5-2
Mode selection softkeys 4-5
Morse code identifier 4-3
N
Nav/Com controls 4-1
NAV1 5-2
NAV2 5-2
Navigation 7-1
Navigation status window 2-2
NAV Frequency Window 4-1
Nearest Airports Page 7-3, 7-5, 7-6,
7-7, 7-8, 7-9, 8-1
Nearest ARTCC & FSS frequencies 7-8
NEXRAD 1-4, 1-7, 10-3, 10-4, 10-5,
10-6
O
OBS 2-7
Obstacles 1-6, 10-9, 12-8
Operation 5-2
Optional
NAV radios 4-3
P
Page group icon 1-8
PFD 1-1, 4-1, 4-4
PLAY key 5-4
PROC key 1-3
Volume/squelch 5-3
Vspeeds 2-3
S
W
Severe thunderstorm 10-5
SIGMET 10-5
Slip/Skid indicator 2-3
Softkey function (MFD) 1-4, 1-6
Speed ranges 2-3
Squelch 5-3
Store Flight Plan 8-5
Stormscope lightning data 10-1
Strike 10-2
Strike mode 10-2
System annunciations 12-1, 12-3
System message advisories 12-6
WARN 2-7
Warning 12-1
Weather data link page 10-4
Weather product symbol 10-5
Weather product symbols 10-6
Weather warnings 10-5
Wind direction 10-5
Wind speed 10-5
X
XM weather 10-3
XPDR softkey 4-5
T
TA 10-7, 12-5
TAF 10-3
TAS 10-8, 10-9, 12-5, 12-12
Terrain 10-9, 12-8
TIS 1-4, 10-7, 12-5, 12-15
Tornado 10-5
Traffic advisory 10-7, 10-8, 10-9, 12-5
Traffic map page 10-7, 10-8, 10-9
Transponder 4-5
Transponder Status bar 4-5
Trend vector 2-6
Trim 3-2
Tropical storms 10-5
Turn rate indicator 2-6
TX 4-3
V
R
Red pointer 2-3
Remove departure, arrival, or approach
8-5
Replies 4-5
Reversionary mode 11-1
Index-2
Rudder trim 3-2
R indication 4-5
Vertical Deviation/Glideslope indicator 2-4
VFR code 4-5
VHF 4-1
Voice alerts 12-2, 12-5
VOL/PUSH ID 4-2
VOL/PUSH SQ 4-2, 4-3
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Garmin G1000 Cockpit Reference Guide for the Mooney M20M & M20R
Garmin International, Inc.
1200 East 151st Street
Olathe, KS 66062, U.S.A.
p: 913.397.8200 f: 913.397.8282
Garmin AT, Inc.
2345 Turner Road SE
Salem, OR 97302, U.S.A.
p: 503.391.3411 f: 503.364.2138
Garmin (Europe) Ltd.
Unit 5, The Quadrangle
Abbey Park Industrial Estate
Romsey, SO51 9DL, U.K.
p: 44/0870.8501241 f: 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road
Shijr, Taipei County, Taiwan
p: 886/2.2642.9199 f: 886/2.2642.9099
www.garmin.com
© 2004, 2005 Garmin Ltd. or its subsidiaries
190-00450-01 Rev. A