Garmin Quest 2 GPS Receiver User Manual

Owner’s Manual
Quest® 2
pocket-sized navigator
© 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial
Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr,
Taipei County, Taiwan
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored
in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of
this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that
such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial
distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content
without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for current updates and
supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, AutoLocate®, TracBack®, and MapSource® are registered trademarks, and Quest™ is a trademark of Garmin Ltd. or its subsidiaries and
may not be used without the express permission of Garmin.
September 2006
Part Number 190-00675-00 Rev. A
Printed in Taiwan
Introduction Introduction
Thank you for purchasing Toyota’s portable navigation Quest™ 2
by Garmin. To get the most out of your new navigation system, go
through this owner’s manual and learn the operating procedures for
your unit.
Introduction: contains the Table of Contents and Safety
Information.
Getting Started: provides information to help get you started. If
you have never navigated with a GPS unit, try the “Tutorial”
on page 2.
Basic Operation: teaches you how to use your Quest 2 to find
items, create routes, and initiate a TracBack®.
Using the Main Pages: describes the Map page and other main
pages of your Quest 2.
Customizing Your Quest 2: explains how to change settings to
meet your specific needs.
Appendix: contains tips and shortcuts, information about care and
Safe Mode, specifications, and regulatory information.
Index: provides key words to help you find information.
Manual Conventions
This manual uses the term “select” when you need to choose an
icon, button, or tab. To select something, use the Rocker to move
the cursor (or highlighted area) to the position. To activate the
selection, press the OK key.
This manual uses the term Warning to indicate a
potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
This manual uses the term Caution to indicate a
potentially hazardous situation, which, if not avoided, may
result in minor injury or property damage. The term may
also be used without the symbol to alert you to avoid unsafe
practices.
Understanding GPS: describes the basics of GPS navigation and
the features on the GPS Information page.
Quest® 2 Owner’s Manual
Introduction > Table of Contents
Table of Contents
Introduction............................................................................i
Warning......................................................................................iii
Caution.......................................................................................iv
Getting Started......................................................................1
Introducing the Quest 2.............................................................. 1
Tutorial........................................................................................ 2
Vehicle Installation...................................................................... 4
Turning the Quest 2 On and Off................................................. 5
Using the Keys........................................................................... 6
Basic Operation....................................................................8
Finding Places and Routing to Them ........................................ 8
My Locations............................................................................ 14
Setting Your Home Location..................................................... 18
Using TracBack........................................................................ 19
Planning and Modifying Routes .............................................. 21
Using the Main Pages........................................................27
Map Page................................................................................. 27
Next Turn Page........................................................................ 30
Current Route Page................................................................. 31
Trip Information Page............................................................... 32
Customizing the Overall System Setup.................................... 36
Customizing the Route Settings............................................... 37
Customizing the Units Settings................................................ 38
Changing the Time Settings..................................................... 38
Changing the Track Setup........................................................ 39
Customizing the Welcome Page.............................................. 40
Viewing Software and Unit Information.................................... 40
Understanding GPS............................................................41
The GPS Information Page...................................................... 41
Appendix.............................................................................45
Quest 2 Shortcuts..................................................................... 45
Data Fields............................................................................... 45
Adding Maps to Your Quest 2................................................... 47
Caring for the Quest 2.............................................................. 49
Safe Mode................................................................................ 49
Specifications........................................................................... 50
Product and Regulatory Information......................................... 51
Toyota Limited Warranty........................................................... 52
Index....................................................................................53
Customizing Your Quest 2 . ..............................................33
Customizing the Map Page...................................................... 33
Customizing the Display........................................................... 35
ii
Quest® 2 Owner’s Manual
Introduction > Safety Information
Warning
Failure to avoid the following potentially hazardous situations could
result in an accident or collision resulting in death or serious injury.
Always operate the vehicle in a safe manner. Do not become distracted
by the Quest 2 while driving, and always be fully aware of all driving
conditions. Minimize the amount of time spent viewing the screen of the
Quest 2 while driving and use voice prompts when possible. Do not enter
destinations, change settings, or access any functions requiring prolonged
use of the unit’s controls while driving. Pull over in a safe and legal
manner before attempting such operations.
The Quest 2 contains a non-user-replaceable, rechargeable lithiumion battery. The battery may present a risk of fire or chemical burn if
mistreated.
•
•
Do not remove from the unit, heat unit above 140°F (60°C), or
incinerate.
Dispose of unit properly. Contact your local waste disposal
department for information on properly disposing of lithium-ion
batteries.
When navigating, carefully compare information displayed on the Quest 2
to all available navigation sources, including information from street signs,
visual sightings, and maps. For safety, always resolve any discrepancies or
questions before continuing navigation.
WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive
harm. This Notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer
to our Web site at www.garmin.com/prop65.
Quest® 2 Owner’s Manualiii
Introduction > Safety Information
Caution
Failure to avoid the following potentially hazardous situations may
result in injury or property damage.
The Quest 2 is designed to provide you with route suggestions. It does
not reflect road closures or road conditions, traffic congestion, weather
conditions, or other factors that may affect safety or timing while driving.
Use the Quest 2 only as a navigational aid. Do not attempt to use the Quest
2 for any purpose requiring precise measurement of direction, distance,
location, or topography. This product should not be used to determine
ground proximity for aircraft navigation.
The Global Positioning System (GPS) is operated by the United States
government, which is solely responsible for its accuracy and maintenance.
The government’s system is subject to changes which could affect the
accuracy and performance of all GPS equipment, including the Quest 2.
Although the Quest 2 is a precision navigation device, any navigation
device can be misused or misinterpreted and, therefore, become unsafe.
Map Data Information: One of the goals of Garmin is to provide customers with the most complete and accurate cartography that is available to us at a
reasonable cost. We use a combination of governmental and private data sources, which we identify in product literature and copyright messages displayed to the
consumer. Virtually all data sources contain inaccurate or incomplete data to some extent. In some countries, complete and accurate map information is either not
available or is prohibitively expensive.
NOTICE TO DRIVERS IN CALIFORNIA AND MINNESOTA: State law prohibits drivers in California and Minnesota from using suction mounts on their
windshields while operating motor vehicles. Other Garmin dashboard or friction mounting options should be used. Garmin does not take any responsibility for
any fines, penalties, or damages that may be incurred as a result of disregarding this notice. (See California Vehicle Code Section 26708(a); Minnesota Statutes
2005, Section 169.71.)
iv
Quest® 2 Owner’s Manual
Getting Started > Introducing the Quest 2
Getting Started
Introducing the Quest 2
Flip-up GPS antenna
(Position the antenna parallel to
the surface of the road.)
Power key
Front View
256-Color high-resolution TFT display
Quest® 2 Owner’s Manual
Keypad
USB connector
Power/Speaker connector
External antenna
connector
Back View
Getting Started > Tutorial
Tutorial
This tutorial guides you through the steps for finding a restaurant in
your area and then creating a route to it. If you have never used a
GPS unit, try this simple task. You will see that using your Quest 2
is fast and easy.
Be sure the antenna is unobstructed as it looks for satellites. For
example, it cannot establish a satellite fix if your vehicle is parked
in a garage. Position the antenna so that it is parallel to the
surface of the road so that it can have the best view of the sky.
Step 1: If you have not already done so, flip up the antenna and
snap the Quest 2 into the vehicle mount. See page 4 for additional
instructions. Turn on the Quest 2, if necessary, and acknowlege the
warning message. When the unit has established a satellite fix, it
shows a “Ready to Navigate” message.
Step 2: Press the Find key. The Find Menu appears. Highlight the
Food & Drink icon located in the Find Menu and press the
OK key.
FIND key
Rocker
OK key
Step 3: A list of restaurants in your area appears on a page similar
to the one shown below. Use the Rocker to highlight a restaurant
in the list. Then press the OK key.
Map page
Use the Rocker to
highlight a restaurant.
Quest® 2 Owner’s Manual
Getting Started > Tutorial
Step 4: Information about the restaurant appears on a page similar
to the one shown below. To create a route to this restaurant,
highlight the Route To button located at the bottom of the page.
Then press OK.
The Quest 2 calculates the route and provides directions. Follow
the purple line on the Map page to your destination.
Select Route To to
create a route to this
restaurant.
Quest® 2 Owner’s Manual
Getting Started > Vehicle Installation
Vehicle Installation
Tab
You can install and store the Quest 2 in the vehicle mount. The
Quest 2 runs off power from your vehicle when the ignition is
turned on. Be sure the vehicle ignition is turned off before you
install or remove the unit from the mount.
To install the Quest 2 in the mount:
1. Flip up the GPS antenna to a 90° angle on the back of the
Quest 2.
2. Insert the bottom of the Quest 2 into the bottom of the
mount, as shown. The antenna fits through the opening in
the back of the mount.
To remove the Quest 2, push the tab
up and pull the Quest 2 forward.
Note: Make sure the tabs are located and locked correctly.
To remove and store the Quest 2:
1. Push the tab up that holds the Quest 2 in place (see above).
2. Pull the Quest 2 forward and then out of the mount.
3. Snap the Quest 2 back into the mount so that it is fully
seated.
Quest® 2 Owner’s Manual
Getting Started > Turning the Quest 2 On and Off
Turning the Quest 2 On and Off
Press and hold the Power key on the front of the unit to turn
it on or off. When turned on, the Welcome page appears briefly,
followed by a Safe Driving Warning Message. Press the OK key
to acknowledge the message. Your Quest 2 automatically starts
searching for satellite signals to find your current location. The first
time the Quest 2 acquires satellites it may take several minutes.
Afterward, acquisition times are quicker during normal use.
Turning Off Satellite Reception for Indoor Use
You can set your Quest 2 to indoor use, which stops satellite
reception and conserves battery power. Thoroughly familiarize
yourself with the routing features of the Quest 2 by
simulating routes.
NOTE: If the unit prompts you to enter a security code, contact
your Toyota dealer.
To turn off satellite reception:
1. Press the Page
key to open the Map page.
2. Press the Menu key.
3. Highlight Use Indoors and press OK. GPS is disabled.
If your unit is in the vehicle mount, it turns on automatically when
you start your vehicle. When you turn off your vehicle, the External
Power Lost message appears. Press any key to switch the unit to
battery power. Otherwise, the Quest 2 turns off after 30 seconds.
Quest® 2 Owner’s Manual
To turn on satellite reception:
1. Press the Page
key to open the Map page.
2. Press the Menu key.
3. Highlight Acquire Satellites and press OK. GPS is
enabled, and your Quest 2 begins to acquire satellite
signals.
Getting Started > Using the Keys
Using the Keys
Use the keys to perform specific tasks such as finding places or planning routes. With the exception of the Power key, press and quickly
release a key to perform its function. If a key has a secondary function, press and hold the key to activate it.
Power—press and hold to turn the unit on or off.
Press once to adjust the illumination of your screen.
When the illumination window appears, use the
Rocker to move the slider to the left or right to dim
or brighten your backlight. Press OK.
Find—press to search for cities, addresses, and
other points of interest. Press Find twice to open
the Recent Finds menu. Press and hold Find to
“Route Home” (see page 18).
Out—zooms out on the Map page. Also scrolls
down a list.
In—zooms in on the Map page. Also scrolls up
a list.
Page—press to open pages. Press Page
to
close the current window or menu and return to the
previous page. When you are entering data, press
Page
to cancel the data entry and restore the
previous value.
Menu—press to show a menu of options for
the current page. Press Menu twice to open the
Settings menu. Press and hold Menu to open the
Route Options menu.
OK—press to select items. Press OK to view
information pages when panning the Map page. To
save your current location in My Locations, press
and hold OK.
Speak—triggers your unit’s “voice” to repeat the next
turn or current destination when you are navigating a
route. Press and hold to adjust the volume. The unit
must be in the vehicle mount to hear audio commands.
Rocker—press to highlight options or move the
map pointer in any direction.
Quest® 2 Owner’s Manual
Getting Started > Using the Keys
Selecting Options and Entering Data
Use the OK key and the Rocker to select options and activate your
selections.
To select and activate an option or on-screen button:
1. Use the Rocker to move up, down, right, or left to the
selection or on-screen button.
2. Press OK to activate the feature.
Use the Rocker to select a letter, number, or symbol, and then
press OK. To create spaces, select the blank space between the Y
and Z. Use the Clear (Back) box to delete letters/numbers. The ◄
and ► keys are backspace and forwardspace keys. The up arrow
changes the capital letters to lower case and the numbers to
symbols. Use the Return key to create a new line. When you
have entered all text, select Done.
To exit a menu or return to the previous setting:
Press Page . The Page key moves backward through
your steps or menus.
Using the �����������
On-screen Keyboard
The on-screen keyboard opens when you need to enter data, such
an address or a city. The on-screen keyboard is used in a variety of
places throughout the Quest 2. Its appearance may alter, depending
on your purpose for using it, but it always functions the same way.
The up arrow changes the
capital letters to lower case
and numbers to symbols.
Return key
Quest® 2 Owner’s Manual
Basic Operation > Finding Places and Routing to Them
Basic Operation
Finding Places and Routing to Them
Use the Find Menu to locate and create routes to cities, addresses,
parks, restaurants, or hotels.
Find Menu
Press the Rocker down to see more Find categories.
To find a place and route to it:
1. Press the FIND key. The Find Menu appears.
2. Highlight a category
to help you find your
destination, such as Food
& Drink, Lodging, or All
Points of Interest. Press
OK. A list of places near
your current location
Find Menu Results List
appears.
3. Highlight the place and
press OK. An information
page appears.
4. Highlight Route To and
press OK. The Quest 2
calculates your route.
Information Page
Quest® 2 Owner’s Manual
Basic Operation > Finding Places and Routing to Them
Advanced Search Methods and Tips
The search results list can be quite long. Use the following tips to
narrow your search.
Entering Containing Letters
If you know the name of the place you are searching for, select
the <Containing> box. Use the
on-screen keyboard to enter letters
contained in the name. The more
fully you type the name, the more
accurate your search results. For
example, typing “SU” in order to
find Sun’s Deli returns names such
Using the Containing Field
as Subway and Tropik Sun.
Searching Sub-Categories
If you would like to search for a
type of food (such as Chinese, Deli,
International, Fast Food), highlight
the All Categories box and press
OK. Highlight a food category
(sub-category) and press OK. A new
list appears filtered with the selected
category.
Quest® 2 Owner’s Manual
Panning and Finding
You can find places that are beyond your current location by
panning to a particular area on the map. Open the Map page
and pan the map to the location. Press the Find key, and the
unit searches for places near the map pointer. See page 28 for
information about panning the map.
Finding Places Near this Place
After you have found a place, open the item’s information page.
To find another place (such as a hotel or restaurant) near this place,
highlight Find Near and press OK.
Saving this Place to My Locations
After you have found a place, open the item’s information page.
Highlight Save and press OK to save this place to My Locations.
Using the Information Page Menu
After you have found a place, open the item’s information page and
press the Menu key to reveal more options.
Using Sub-Categories
To see where this item is located on the map, select Show Map.
For step-by-step directions from the place to your current location,
select Directions to Me. Select Find Near Current Route to list
all places along your current route.
Basic Operation > Finding Places and Routing to Them
Finding an Address or Intersection
To search for an address or intersection, select Addresses or
Intersections from the Find Menu. In both cases, a search wizard
appears that allows you to enter street information.
4. Enter the address number and street using the on-screen
keyboard. For intersections, you only need to enter street
names.
To find an address or intersection:
1. Press Find, highlight Addresses or Intersections, and
press OK.
2. Highlight a state and press OK.
5. A list of addresses or intersections appears. Highlight the
place you are looking for and press OK.
6. To create a route to this address, highlight Route To and
press OK.
3. Highlight Search All Cities and press OK.
10
Quest® 2 Owner’s Manual
Basic Operation > Finding Places and Routing to Them
Finding a City
Finding an Exit
To find a city:
To find an exit:
To search for a city, select Cities from the Find Menu. A list of 50
cities near your current location appears.
1. Press Find, highlight Cities, and press OK. A list of cities
appears. Use the Rocker to move down the list.
2. Highlight the <Containing> box and press OK to narrow
your results or find a city not on the list. Enter the name of
the city you are searching for using the on-screen keyboard.
3. Highlight a city and press OK. An information page appears.
4. To go to the city, highlight Route To and press OK.
Select Exits from the Find Menu to locate exits on highways,
freeways, and interstates.
1. Press the Find key, highlight Exits, and press OK. All exits
on the highway or interstate that is closest to your current
location are listed.
2. To search for a particular road exit, press Menu, highlight
Select Exit Road, and press OK. Enter the name of the
road using the on-screen keyboard.
3. If you know you want to stop at an exit that has a particular
type of service, such as a gas station or rest area, select the
All Categories box and press OK. Then select a category
from the list.
4. Use the Rocker to highlight an exit from the search results
list and press OK. An information page for that exit appears.
Services at this exit appear on the exit’s information page.
Highlight the service you want to visit and press OK to view
information about it.
5. To go to the exit, highlight Route To and press OK.
Quest® 2 Owner’s Manual11
Basic Operation > Finding Places and Routing to Them
Finding Recently-Found Places
Your Quest 2 stores the 50 places you have found most recently.
The most recently-reviewed item is at the top of the list.
To find a recently-found place:
1. Press Find, highlight Recent Finds, and press OK. A list of
recently-found items appears.
2. To narrow your search,
highlight All Categories and
press OK.
3. Highlight a category from the
list and press OK. The 15
most recent finds from the
category appear.
4. Highlight a place and press
OK.
5. To create a route to this
place, highlight Route To
and press OK.
The Quest 2 only stores places that you actually view. For example,
suppose you search for a restaurant by name and five names appear.
If you view information on two of them, then these two restaurants
are stored in your Recent Finds list.
12
Deleting Recently-Found Places
If you want to delete a place from the Recent Finds list, highlight
the place’s name and highlight the red . Press OK, and the name
is removed from the list.
To remove all names in the Recent Finds list, press Menu while
on the Recent Finds page. Highlight Remove All and press OK.
Note: Deleting an item from the Recent Finds list only
removes the item from this list. It does not delete the actual city
from the Map page, your find database, or My Locations.
Quest® 2 Owner’s Manual
Basic Operation > Finding Places and Routing to Them
Planning a Trip
If you are planning a trip and would like to find vacation spots
ahead of time, consider using the “chain find” method described
below. You can also follow these instructions for finding places
while you are already on a trip.
1. Find the city you plan to visit. See page 11 for more
instructions. In our example, Overland Park, KS is chosen.
2. Highlight Find Near and
press OK.
3. Select Lodging to look for
a place to stay in Overland
Park.
4. Your Quest 2 returns the
names of places to stay.
Highlight a place to stay and
press OK. In our example,
Bed and Breakfast Kansas
City is the lodging place.
5. From the Bed and Breakfast
information page, highlight
Find Near and press OK.
Then highlight Food & Drink and press OK.
6. A list of all eating establishments near Bed and Breakfast
Kansas City appears. Highlight a restaurant and press OK.
7. To save the restaurant to your My Locations list, highlight
Save from the information page.
Restaurants near your lodging choice in Overland Park
You can also find entertainment, services, and a variety of other
places near your chosen lodging area in the city of your choice.
When you are ready to take your trip, simply find these places in
your Recent Finds or My Locations list. For more information on
trip planning, see “Planning and Modifying Routes” on page 21.
Quest® 2 Owner’s Manual13
Basic Operation > My Locations
My Locations
You can save your favorite places to the My Locations category of
the Find Menu. This allows you to easily find your favorite places
later. For example, if you have found a great campsite, you can
save the place to My Locations. Then when you want to return to
the campsite, you can quickly find and route to it.
Saving Your ��������������������
Favorite Places in “My
�
Locations”
You can save up to 500 locations using four basic methods.
•
•
•
•
Save an item you have found using the Find Menu.
Save your present location from the Where Am I? page.
Save a new location from the map using the Rocker.
Enter a new location’s position coordinates manually.
Saving an Item from the Find Menu
As discussed in the previous sections, you can save items you have
found using the Find Menu.
To save a place from the Find Menu:
Where Am I?
Use the Where Am I? feature to find out where you are and save
your location. This is particularly useful if you are traveling off
road or any place where street signs or navigational markers are not
available.
You must have a valid position (2D or 3D) fix to mark your present
location. You can determine the satellite fix by looking at the GPS
page. For more information, see “Understanding GPS” on page 41.
To find out where you are and save your location:
1. Press the Find key, highlight Where Am I?, and press OK.
Or, press and hold the OK key.
2. A Where Am I? page
appears, listing your current
location and the nearest
major intersections, if
available. Highlight Save
and press OK to �����������
save your
location to My Locations.
1. Press Find. Highlight the search category and press OK.
2. Highlight the place you want to save and press OK.
3. From the information page, highlight Save and press OK.
14
Quest® 2 Owner’s Manual
Basic Operation > My Locations
Saving a Map Location
As you pan the map, you can save a location you see to My
Locations. See page 28 for information about panning the map.
To save a place on the map to My Locations:
1. Press Page
to open the
Map page.
2. Press the Rocker to select
the place you want to save.
Press OK.
3. An Information page opens.
Highlight Save and press
OK.
4. The Saved as My Location
page opens. This page
allows you to rename the
saved location, select a
new symbol, and file the
saved location in a category.
Highlight the on-screen OK
button and press the OK key
when you are finished.
Entering a Location’s Coordinates
You can manually enter location coordinates to create a location.
This method can be useful for creating a location at a specific
latitude/longitude position from a chart.
To enter a location’s coordinates:
1. Press and hold the OK key. Highlight Save and press OK
2. On the Saved as My Location page, use the Rocker to
highlight the Location field and press OK.
3. Use the on-screen keyboard to enter the position
coordinates and press OK when finished.
4. To change other information, highlight the appropriate field
and press OK. After entering your changes, highlight the
on-screen OK button and press the OK key.
Quest® 2 Owner’s Manual15
Basic Operation > My Locations
Editing a Saved Location
You can edit many aspects of a saved location: the name, symbol,
location coordinates, comment, elevation, and category.
To edit the saved location:
1. Press the Find key. Highlight My Locations and press OK.
2. Highlight the saved location you want to edit and press OK.
3. Highlight the item you want to
change and press OK.
4. Use the on-screen keyboard
to enter new information.
5. When you are done editing
the saved location, press the
Page
key to exit.
To create a saved location category:
1.
2.
3.
4.
5.
6.
To assign a category to a saved location:
1.
2.
3.
4.
Organizing Saved Locations into Categories
You can organize your saved locations into categories to help you
manage and use your saved locations. For example, you can create
a “Vacation” category that stores all of the saved locations for your
upcoming vacation. When the vacation is over, you can simply
delete all the saved “Vacation” locations by pushing a few buttons.
16
Press the Find key. Highlight My Locations and press OK.
Highlight the saved location you want to edit and press OK.
Highlight the Categories field and press OK.
Highlight Edit… and press OK.
Highlight Add New… and press OK.
Use the on-screen keyboard to enter the name of the new
category. Highlight Done and press OK when finished.
Press the Find key. Highlight My Locations and press OK.
Highlight the saved location you want to edit and press OK.
Highlight the Categories field and press OK.
From the list, highlight the category you want to assign the
saved location to and press OK.
To delete a category:
1.
2.
3.
4.
5.
Press the Find key. Highlight My Locations and press OK.
Highlight the location you want to edit and press OK.
Highlight the Categories field and press OK.
Highlight Edit… and press OK.
Highlight the category you want to delete. Highlight the red
to the right of the category and press OK to delete it.
Quest® 2 Owner’s Manual
Basic Operation > My Locations
Deleting Saved Locations
You can delete saved locations when they are no longer needed.
To delete a saved location:
1. Press the Find key. Highlight
My Locations and press OK.
2. Highlight the saved location
you want to delete.
3. Highlight the red
to the
right of the location and press
OK to delete it.
F��������
inding My Locations
When you save an item, it is saved in the My Locations category
of the Find Menu. To find a location you have saved, open the My
Locations category of the Find Menu.
To find a saved location:
1. Press the Find key, highlight My Locations, and press OK.
2. To narrow your search, highlight All Categories and press
OK. Highlight the category the saved location is assigned to
and press OK.
To delete saved locations by symbol or category:
Press the Find key, highlight My Locations, and press OK.
Press Menu, highlight Delete…, and press OK.
Highlight By Symbol… or By Category… and press OK.
When deleting by symbol, highlight the symbol of the saved
location you want to delete and press OK. When deleting
by category, highlight the category you want to delete and
press OK.
5. Highlight Yes and press the OK key to confirm. Highlight No
and press OK to exit without deleting.
1.
2.
3.
4.
3. To further narrow your search, highlight All Symbols and
press OK. Highlight the symbol assigned to the saved
location and press OK.
4. Use the Rocker to select the saved location and press OK
to open the information page.
5. Highlight Route To and press OK to go to this location.
Quest® 2 Owner’s Manual17
Basic Operation > Setting Your Home Location
Setting Your Home Location
Your Quest 2 allows you to set a “Home” location that can be your
home, office, or any other place to which you return most often.
After you set your Home location, you can opt to go Home. For
example, if you are traveling in a new city or down an unknown
street and you want to easily find your way home, simply press and
hold the Find key. Your Quest 2 automatically redirects you to
your Home location.
To route Home:
Press and hold the FIND key. The Quest 2 automatically
creates a route to your Home location.
Changing Your Home Location
If you travel frequently, you may want to change your Home
location to a new location, such as a hotel or your meeting place, so
you can find your way “home” in unfamiliar surroundings.
To change your Home location:
1. Press Find, highlight My Locations, and press OK.
2. Highlight your Home location and then highlight the red
Press OK. Highlight Yes and press OK to confirm.
3. Follow the previous instructions to reset your Home
location.
.
To set a Home location:
1. Press Menu, highlight Route Options, and press OK. A
Route Options menu appears.
2. Highlight Set Home Location and press OK.
3. Highlight one of the three options and press OK.
4. Find your Home location using the selected option. Your
Home location is set.
18
Quest® 2 Owner’s Manual
Basic Operation > Using TracBack
Using TracBack
The Quest 2 records an electronic breadcrumb trail or “track log”
as you travel. As a result, you can retrace your recent movements
using the TracBack® feature. This feature is particularly useful
when navigational markers are not readily available.
The track log starts recording as soon as the Quest 2 gets a
location fix. For the best results, clear the track log before you start
traveling. When the track log is full, new track points overwrite the
oldest track points.
To use TracBack:
1. Press the Find key, highlight Where Am I?, and press OK.
2. Highlight TracBack and press OK.
3. If you want to travel to the beginning of your track, highlight
Yes and press OK.
To select a spot along your track to travel to, highlight No
and press OK. Use the Rocker to select the point to which
you want to travel and press OK.
4. A TracBack Preference window appears.
Highlight the preferred method and press
OK.
If you have selected to follow roads (Faster Time or Shorter
Distance), the Quest 2 creates a turn-by-turn route to the selected
end point. Follow the route just as you would follow any route.
If you selected to follow the track, you can use the Map page and
the Compass page to guide you along the path. See the next page
for more information about the Compass page.
Quest® 2 Owner’s Manual19
Basic Operation > Using TracBack
Following Your Track with the Compass Page
If you have selected to follow your track
(Follow Track), the Quest 2 traces your path to
the destination. You can use the Map page and
Compass page to navigate to your destination.
Press the Page
key to view the Compass page. The middle of
the page features a rotating “compass ring” that shows your course
while you are moving. Your present heading is indicated at the top
of the compass ring. The direction of the next turn is indicated by
an arrow in the middle of the compass ring and a bearing “bug” on
the outside of the compass ring. Directions to your next point or
turn appear in the top text bar.
Text bar
Rotating
compass ring
If the arrow points up, you are going in the correct direction. If the
arrow points any direction other than up, turn toward the arrow
until it points up, then continue in that direction.
Bug indicator
Data fields
Note: You must be moving for the compass to update and
display your heading accurately.
You can change the data fields on the Compass page just as you can
on the Map page (page 29). For a complete list and description of
data field options, see page 45.
Instead of the bearing pointer, you can use a course pointer. Press
Menu, highlight Course Pointer, and press OK. The course
pointer now appears in the center of the compass to show you how
to get back on course.
Note: The Compass page is only available when you are
following a TracBack using the Follow Track method. See
page 19 for more information.
Bearing pointer
20
Quest® 2 Owner’s Manual
Basic Operation > Planning and Modifying Routes
Planning and Modifying Routes
Use Route Planner to plan your routes before you even leave the
house. The Route Planner allows you to select a start point and
a destination, and it automatically saves the route. You can also
modify the route to add extra stops (via points) or avoid certain
roads.
Planning a Route
Planning routes is fast and easy: simply pick a starting location and
an ending location.
To plan a route:
1. Press and hold the .
Menu key.
2. Highlight Route Planner
and press OK. From the
Route List page, highlight
New and press OK.
3. From the Route Planner
page, highlight <Select
your starting location> and press OK. Highlight one of the
four options (described to the right) and press OK. Select
your starting location.
Quest® 2 Owner’s Manual
4. From the Route Planner page, highlight <Select your
destination> and press OK. Highlight one of the options
and press OK. Select your ending location.
Highlight Navigate to start navigating this route. If you want to
stop the route, select Stop Navigation from the Route Options
menu. To resume the route, select Resume Navigation.
Finding Route Points
Your Quest 2 provides four options for selecting your starting and
ending locations:
None—choose this option to begin the route wherever you are
located at the present time.
Current Location—choose this option to begin or end the route at
the address at which you are currently located. For example, if your
current location is at 915 Elm, the Quest 2 enters this address as the
Current Location.
Find Menu—choose this option to search for a starting or ending
location using the Find Menu.
Use Map—choose this option to find a point on the Map page.
When the Map page appears, use the Rocker to move the map
pointer to the location and press OK.
21
Basic Operation > Planning and Modifying Routes
Saving a Route
Your Quest 2 automatically saves a route created with the Route
Planner. You can also save an active route during navigation or
after you have reached the destination.
To save an active route:
1. Press and hold the Menu key.
2. Highlight Save Route and press OK. Press OK again at the
verification window.
Your Quest 2 can hold up to 50 saved routes. If you save routes
prior to taking a trip, you only need to retrieve the appropriate route
and activate it as you prepare to leave.
The vehicle icon indicates
the route is active.
To select a saved route:
3. Highlight the name of the route and press OK. An
information page for your selected route appears.
4. To activate the route, highlight Navigate and press OK.
5. If you want to change the route by adding via points, use
the Rocker to highlight the Via Points box and press OK.
See “Adding Via Points” in this section for more information.
Deleting a Saved Route
You can delete a single route or all of the saved routes in your
Quest 2.
To delete a route:
1. Press and hold the Menu key.
2. Highlight Route Planner and press OK. A list of your saved
routes appears.
3. To delete one route, highlight the name of the route. Use the
Rocker to highlight the red
to the right of the route name
and press OK. Highlight Yes when the verification window
appears and press OK.
To delete all saved routes, press the Menu key. Highlight
Delete All and press OK. Highlight Yes when the
verification window appears and press OK.
1. Press and hold the Menu key.
2. Highlight Route Planner and press OK. A list of your saved
routes appears.
22
Quest® 2 Owner’s Manual
Basic Operation > Planning and Modifying Routes
Recalculating a Route
The Quest 2 will automatically recalculate your route if you
stray from the current route. You can also prompt the Quest 2 to
recalculate your route. For example, if you change your route
preference (page 37), you can recalculate your route based on your
new preference.
To recalculate your route:
1. Press and hold the Menu key.
2. Highlight Recalculate and press OK.
Adding a Detour
When you are navigating a route, you might need to take a detour
to avoid a roadblock or construction. After you select a detour
distance, your Quest 2 calculates a new route and provides you
with new driving instructions. The detour is saved until you stop
the current navigation or until you turn off the unit.
To set a detour:
1. Press and hold the Menu key.
2. Highlight Detour and press OK.
3. Highlight a detour distance and press OK.
Quest® 2 Owner’s Manual
Your Quest 2 makes every possible attempt to get you back on the
original route at your requested distance; however, the distance
may be longer if no other roads can take you back to your original
route. Sometimes, the route you are currently taking might be the
only reasonable option. If so, you will not be able to take a detour.
Adding Via Points
Via points are extra stops you make on the way to your final
destination. You can add stops to the route you are currently
navigating, to the route you are planning, or to a route that you
have previously saved.
To add via points to a saved route:
1.
2.
3.
4.
5.
6.
Press and hold the Menu key.
Highlight Route Planner and press OK.
Highlight the route to add extra stops to and press OK.
Highlight <Select to add via point> and press OK.
Highlight a method to find the location and press OK.
Highlight the location of the point. Continue until all points
are added to the route.
23
Basic Operation > Planning and Modifying Routes
Arranging Via Points
When you have entered all of the points, your Quest 2 can arrange
them in the most efficient order so that you can visit each point
without a lot of extra traveling.
Adds a via point (extra stop) and places it ahead of the
existing point.
Deletes the point.
Moves the point up or down.
To arrange the order of the via points:
Press and hold the Menu key.
Highlight Route Planner and press OK.
Highlight the route you want to arrange and press OK.
Select the point you would like to move in the route order.
Highlight the up or down arrow and press OK. The
point is moved up or down one spot.
5. Continue arranging the points as necessary.
1.
2.
3.
4.
24
To optimize the route:
1.
2.
3.
4.
Press and hold the Menu key.
Highlight Route Planner and press OK.
Highlight the route you want to arrange and press OK.
Press Menu, highlight Optimal Via Order, and press OK.
The unit rearranges all of your extra stops based on your route
preference (Faster Time, Shorter Distance, or Off Road). See
page 37 for more information on route preferences. If you change
your route preference, recalculate the route based upon the new
route preference (page 23).
To reverse the order of the route:
1.
2.
3.
4.
Press and hold the Menu key.
Highlight Route Planner and press OK.
Highlight the route you want to reverse and press OK.
Press Menu, highlight Reverse Route, and press OK.
Deleting Via Points
If you decide that you no longer want to visit one of your via
points, select that point and use the Rocker to highlight the red
to the right of the via point. Press OK, and the point is immediately
removed from the route.
Quest® 2 Owner’s Manual
Basic Operation > Planning and Modifying Routes
Avoiding Roads and Areas
You can avoid areas and certain road types on your route. For
example, if an area of roads is usually highly congested, you can
add that area to your Avoid List.
To add an avoidance to your route:
1. Press and hold MENU to open the Route Options menu.
2. Highlight Avoidances and press OK.
3. Highlight the maneuver or road type you want to avoid and
press OK. The Quest 2 avoids all roads types that have a
check mark in the Avoid… box.
Avoidances Page
To avoid a road:
Press and hold MENU to open the Route Options menu.
Highlight Avoidances and press OK.
Highlight the Add… button and press OK.
Highlight Road Avoidance and press OK to select a street
to avoid on your routes. A map appears, enabling you to
mark a “start point” on a road.
5. Use the Rocker to move the map pointer to the beginning
point of the road you want to avoid and press OK. A blue
push pin marks the start point.
6. Use the Rocker to move the map pointer to the end of the
road you want to avoid and press OK.
1.
2.
3.
4.
7. A map of the avoided road appears. Press OK.
The Avoidances page, shown to the left, lists the avoided road with
a default name (the street names).
Quest® 2 Owner’s Manual
25
Basic Operation > Planning and Modifying Routes
To avoid an area:
Press and hold MENU to open the Route Options menu.
Highlight Avoidances and press OK.
Highlight the Add… button and press OK.
Highlight Area Avoidance and press OK. A map appears,
enabling you to mark a “start point.”
5. Use the Rocker to move the map pointer to the first corner
of the area you want to avoid and press OK. A blue push pin
marks the start point.
6. Use the Rocker to move
the map pointer to the far
corner of the area you
want to avoid and press
OK. You have drawn a
dark rectangle around the
area you want to avoid.
7. A map of the avoided area
appears. Press OK.
1.
2.
3.
4.
The Avoidances page, shown above, lists the avoided area with a
default name (Area 000).
After you enter the avoid areas and roads, your Quest 2 avoids
these roads/areas unless no other roads are available, until you
remove them from the Custom Avoidances list, or until you
uncheck them.
To uncheck an avoidance, select the check box to the left of the
avoidance name and press OK. An unchecked box indicates that
the road/area will not be avoided.
To change the name of an avoidance, select the A
and use the
on-screen keyboard to create a new name. Select the clock
to
choose the date that you want the avoidance to expire. Select the
red X
to permanently delete the avoidance.
A
Uncheck the
box to the
left of the
avoidance to
deactivate it.
Clock
Red X
Avoidances Page
26
Quest® 2 Owner’s Manual
Using the Main Pages > Map Page
Using the Main Pages
Zooming In and Out of the Map
Map Page
The Map page is one of the main pages of the Quest 2. Whether
you are navigating a route or simply traveling with your Quest 2
turned on, the map shows your current location and surrounding
street detail. Customizable information boxes called data fields
provide information such as your current speed, your traveling
direction, and names of upcoming streets.
A text bar at the top of the map indicates the status of the GPS
receiver. When you turn on your Quest 2, the text bar indicates
that the GPS receiver is attempting to locate satellites. After it
establishes a “fix” on your location, the text bar reads “Ready to
Navigate.”
Position icon
(You are here)
Text bar
Data fields
The map has many zoom ranges, from 20 ft to 500 mi. Zoom in
and out of the map by pressing the In and Out keys. The current
zoom range is displayed at the bottom left corner.
Base map .
at 5-mile zoom
MapSource (detailed) map .
at 500-foot zoom
To zoom in and out:
• Press the Out key to zoom out.
• Press the In key to zoom in.
When the selected zoom exceeds the resolution of the data in use,
“overzoom” appears below the zoom range. When MapSource®
data is used, “mapsource” appears below the zoom range.
Zoom range
Quest® 2 Owner’s Manual
27
Using the Main Pages > Map Page
Panning the Map
You can pan the map with the map pointer to view areas of the
map that are not visible on the screen. As you pan past the edge of
the screen, the map moves to provide continuous map coverage.
The position icon indicates your present location and may not
be visible on the screen when you pan the map.
To pan the map:
Press up, down, right, or left on the Rocker.
The map pointer moves the map so you can view different
parts of the map.
As you move the pointer, the distance and bearing from your
present location to the pointer appear in the distance bar. The map
pointer’s location coordinates also appear in the bar. When you
zoom while panning the map, the map pointer stays centered on the
screen.
Position icon
To re-center your location on the screen:
When you are finished panning the map, press the Page
key. The map automatically moves to show your present
location.
Use the pointer to select on-screen map features and review the
item directly from the map.
To view details about an on-screen point:
1. Use the Rocker to move the pointer to the location or map
item. If several items are grouped closely together, zoom in
closer for a better view.
2. Press OK to view more information about the point. The
information and on-screen buttons vary depending on the
type of item selected.
Map pointer
Distance bar
28
Quest® 2 Owner’s Manual
Using the Main Pages > Map Page
Viewing the Map Orientation
You can orient the map in one of two ways. North Up shows the
Map page with North always at the top, as if you were reading a
paper map. Track Up allows the map to automatically rotate so
your direction of travel always appears at the top of the Map page.
If you are using Track up, a white N indicator, in the top left corner
of the Map page, points to the North.
Your Quest 2 is set to show the Map page in Track Up orientation
until you zoom out to the 200-mile zoom range or above. To
change the map orientation settings, see page 33.
Track Up
Data Fields
The Map page displays data fields on the right-hand column of the
page. Information in these fields changes depending on whether
you are navigating a route or just traveling with the Quest 2 turned
on. Data fields also appear on the Trip Information page (page
32) and the Compass page (page 20). For a complete list and
description of data field options, see page 45.
To change the data fields on the Map page:
1. Open the Map page and press the Menu key.
2. Highlight Edit Fields and press OK.
3. Use the Rocker to highlight the data field you want to
change and press OK.
4. Highlight the new data field type in the list and press OK.
5. When you are finished changing the data fields, press Page
to exit.
North Up
Data fields
Quest® 2 Owner’s Manual
29
Using the Main Pages > Next Turn Page
Next Turn Page
When you are navigating a route, the Next Turn page opens
periodically to alert you that you need to turn soon. The Next Turn
page displays a picture of the turn and provides text instructions.
This page disappears after a few seconds. If you need to see it
again, press the Speak key.
Route line
Next Turn
Miles until you
reach the turn
Approximate
time left until you
reach the turn
Next Turn Page
An added bonus to the Next Turn feature is that the Quest 2 “voice”
announces upcoming turns. If you cannot safely view the Next
Turn page, you can hear the verbal directions. Refer to page 6 to
learn how to adjust the volume.
30
The Next Turn page opens and announces the same instructions for
an upcoming turn up to three times:
• Immediately after you make a turn, the Next Turn page
announces the next turn and the distance to the turn. So, if
the next turn is not for 20 miles, you do not need to worry
about navigation instructions for quite a while.
• As you approach the upcoming turn, the Next Turn page
appears again. This message is announced in order to alert
you to change lanes if necessary and start looking for signs
in anticipation of the upcoming turn.
• Just before the upcoming turn, the Next Turn page appears
one last time for that particular turn.
The Next Turn page disappears after a few seconds, and the page
that you were previously viewing reappears. If you want to close
the Next Turn page and return to the previous page, press the Page
key.
If you want to see the Next Turn page again, press the Speak key,
and it reappears. You also can hear the announcement.
The Next Turn page is only available when you are navigating to a
destination.
Quest® 2 Owner’s Manual
Using the Main Pages > Current Route Page
Current Route Page
Another page that is visible when navigating is the Current Route
page, which provides step-by-step route instructions from start to
finish. Press Page
to open the Current Route page.
The Current Route page displays directions for your entire route.
You can look beyond the next turn and even get an estimated idea
of what time you will reach an upcoming turn, provided you do not
make stops along the way.
You can move through the entire list of turns by using the Rocker.
Highlight any of the turns on the list and press OK to view the
Next Turn page for that turn.
The Current Route page is only available when you are navigating
to a destination.
Direction of turn
Cumulative distance to this turn
from your current location
Upcoming driving instructions
Final destination
Total distance to the destination
from your current location
Current Route Page
Quest® 2 Owner’s Manual31
Using the Main Pages > Trip Information Page
Trip Information Page
If you are making a long trip, the Trip Information page can be
very useful. It indicates your current speed and records many
helpful statistics about your trip.
Be certain to reset the trip information (data) before beginning a
trip. If you make frequent stops, leave the Quest 2 powered on
in order to receive satellites. This allows the unit to accurately
measure elapsed time during the trip.
Indicates the unit is connected
to an external power source and
is being charged
Trip Information Page
Indicates the unit is connected
to an external power source and
is fully charged
To change the data fields:
1. Press Page
to open the Trip Information page and then
press the Menu key.
2. Highlight Edit Fields and press OK. A field in the first row,
first column is highlighted, indicating that it can be changed.
3. Use the Rocker to highlight the field you want to change.
Press OK to display a list of field choices. Highlight the
appropriate choice and press OK.
4. Repeat Step 3 until you have finished changing the fields.
Then press Page .
To reset the trip data or the maximum speed:
1. Press Page
to open the Trip Information page.
2. Highlight the Trip or Max buttons and press OK. A message
appears asking if you want to reset the data.
3. Highlight Yes and press OK. The data is reset.
32
Quest® 2 Owner’s Manual
Customizing Your Quest 2> Customizing the Map Page
Customizing Your Quest 2
You can adjust the Quest 2’s settings to suit your needs. You can
make most changes through the Settings page. Access this page by
pressing the Menu key once and then selecting Settings. You can
also access it by pressing the Menu key two times.
Layout Tab
Navtext—displays or hides the
navigational text.
Turn Pointer—displays or hides
the turn pointer that appears
on the Map page when you are
navigating.
Data fields—displays or hides data fields on the Map page. If you
choose to hide the data fields on the Map page, the turn pointer
appears in the lower right-hand side of the page.
Your Quest 2’s factory settings (or default settings) do not need to
be changed in order for your unit to function.
Customizing the Map Page
You can customize the way information appears on the Map page.
Press Menu twice, highlight Map Setup, and press OK. A Map
Setup page appears, which features six sections.
Map Tab
Map Detail—adjusts the amount of detail that is displayed on your
Map page. A higher detail level causes the map to redraw slowly.
For everyday use, keep the view level set to Normal.
Orientation—North Up displays the map with North at the top.
Track Up rotates the map so your current direction of travel is at
the top of the page. See page 29 for more information.
Road Lock—when On, the Quest 2 places the position icon on the
nearest road. Select Off when you are not traveling
on roads.
Quest® 2 Owner’s Manual33
Customizing Your Quest 2 > Customizing the Map Page
AutoZoom—when On, the Map page zooms in and out as you
travel. As you approach a turn, the Map page progressively zooms
in. After the turn is completed, it zooms out to show the next turn.
Color Mode—choose between Land and Water. Unless you are
using a marine map, such as BlueChart, you will probably keep
Land, which is the default value. Water displays the color of water
as white instead of blue.
Line, Point, City, and Area Tabs
Line tab—controls how the track log, railroads, and street labels
are displayed on the Map page.
Point tab—controls how My Locations, exits, and points of
interest (POIs) are displayed on the Map page.
City tab—controls how cities of various sizes are displayed.
Area tab—controls how rivers, lakes, parks, and points of interest
are displayed on the Map page.
The Line, Point, City, and Area tabs contain two common settings,
Text Size and Hide Above:
34
Text Size—specifies how large or small the names of items appear
on the map. If you do not want the name of an item to appear
on the Map page, select Off in the Text Size field. Names with
Medium and Large letters also appear in bold.
Hide Above—specifies the maximum zoom range at which a map
item appears. If Auto is selected, the maximum zoom range is
determined by the Detail setting. If Off is selected, the item is not
shown. Some map data is only visible at certain zoom ranges.
Restoring Map Setup Default Settings
You can restore map settings for each individual tab or for all tabs.
To restore settings to the map setup:
Press Menu twice, highlight Map Setup, and press OK.
Open the tab on which you want to restore the settings.
Press Menu.
To restore the settings on the open tab, highlight Restore
Map Settings and press OK.
5. To restore all map setup settings, highlight Restore All Map
Settings and press OK.
1.
2.
3.
4.
Quest® 2 Owner’s Manual
Customizing Your Quest 2> Customizing the Display
Customizing the Display
You can change the lighting and color on the Quest 2 for optimal
viewing. Press Menu twice, select Display Setup, and press OK.
Backlight Timeout—specifies the amount of time the backlight
stays on when you are not pressing keys. The timeout only applies
when you are using battery power.
Backlight Intensity—specifies how strong the backlight appears.
Operating the backlight at a higher percentage (intensity) uses up
the battery power more quickly.
Color Mode—sets the color mode for your viewing preferences.
Daytime shows a bright and lighter background. Nighttime shows
a black background for easier viewing during the night. Auto
allows the Quest 2 to automatically switch between the two at
sunrise and sunset. Custom allows you to create your own color
scheme for a variety of objects, such as labels, buttons, and text
bars.
To customize the colors:
Highlight Custom for the Color Mode and press OK.
Highlight an item you would like to customize and press OK.
Highlight Change and press OK. A color grid appears.
Use the Rocker to place the pointer over the color you want
to use and then press OK. The new color appears for the
item you selected.
5. Highlight Save Colors and press OK.
1.
2.
3.
4.
Sample page
displaying
custom colors
Custom Color page
To restore the color settings, press the Menu key, highlight
Restore Settings, and press OK.
Quest® 2 Owner’s Manual35
Customizing Your Quest 2 > Customizing the Overall System Setup
Customizing the Overall System Setup
You can customize various system setup features. Press Menu
two times, highlight System Setup, and press OK.
GPS Mode—sets GPS to Normal, WAAS, Battery Saver (which
periodically turns off the GPS receiver to save battery power), or
GPS Off. See “Understanding GPS” beginning on page 41 for
more information.
Text Language—changes all on-screen text to the selected
language. Changing the text language does not affect the display of
map data or user-entered data. Map data is always displayed in the
language in which it is stored in the map.
Voice Language—changes the spoken language.
Voice Guidance—determines when the unit “speaks.”
• Automatic with Chime: The unit chimes and then speaks
status messages and guidance messages during route
navigation. For each turn on a route, the voice gives
instructions three times: after you have completed a turn, as
you are approaching the next new turn, and just before you
reach the next turn.
• Automatic: The unit speaks guidance messages during route
navigation, as described above. It does not give chimes.
Button Only: The unit only speaks when the Speak key
•
is pressed.
External Power Lost—if Turn Off is set, the unit shuts down
after 30 seconds when the unit loses external power. If Stay On is
set, the unit runs on battery power when external power is lost.
36
Keypress Tone—turns the keypress beep On or Off.
To restore these settings, press the Menu key, highlight Restore
Settings, and press OK.
Quest® 2 Owner’s Manual
Customizing Your Quest 2> Customizing the Route Settings
Customizing the Route Settings
You can customize many routing features. Press Menu two times,
highlight Route Setup, and press OK.
Off-Route Recalculate—controls how the unit recalculates the
route when you depart from its original instructions.
• Prompted: You are asked if you want the unit to recalculate
the route.
• Automatic (Announced): The unit automatically
recalculates and announces to the user that it is recalculating.
• Automatic (Silent): The unit automatically recalculates the
route, but it does not announce to the user it is recalculating.
• Off: The unit does not recalculate when you go off route.
Route Preference—determines the criteria used for calculating
your route. If you change your route preference, recalculate the
route based upon the new preference (page 23).
• Faster Time: Routes are faster to drive but may be longer in
distance.
• Shorter Distance: Routes are shorter in distance but may
take more time to drive.
• Off Road: The route is a direct line from your current
location to your destination. This is useful when you are
traveling outside of map areas, or where no roads exist.
• Prompted: You are asked to select the route preference
option before the route is calculated.
Calculation Method—allows you to control how thoroughly the
unit searches for the perfect route.
• Quickest Calculation: This calculation returns the fastest
results, but it might not find the best route.
• Quick Calculation: This takes a bit more time to calculate,
but generates a better quality route.
• Better Route: This generates an even better quality route,
but takes a bit longer to calculate.
• Best Route: This
generates the best route,
but takes the longest time
to calculate.
Calculate Routes for—allows
you to specify your vehicle type.
The unit optimizes the route for
the vehicle type.
To restore these settings, press the Menu key, highlight Restore
Settings, and press OK.
Quest® 2 Owner’s Manual37
Customizing Your Quest 2 > Customizing the Units and Time Settings
Customizing the Units Settings
To restore these settings, press the Menu key, highlight Restore
Settings, and press OK.
Distance and Speed—allows you to change the units used to
measure distance. Statute shows speed in miles per hour and
elevation in feet. Metric shows speed in kilometers per hour and
elevation in meters.
Changing the Time Settings
Press Menu two times, highlight Units Setup, and press OK.
Heading Display—displays your direction of travel in cardinal
letters, degrees, or mils.
Location Format—allows you to select from a variety of formats.
Use the default setting if you are unfamiliar with location formats.
Heading—allows you to select a heading. True shows true north
headings, and Magnetic automatically calculates the magnetic
variation for the geographical area. User allows you to input a
magnetic variation in the Magnetic Variance field. Grid provides
a true north heading as determined by the Location Format.
Vertical Speed—displays vertical speed in feet/minute, meters/
minute, or meters/second.
Elevation—displays elevation in feet or meters.
Datum—allows you to select from over 100 different map datums
to match almost any paper map or chart. Use the default setting if
you are unfamiliar with datums.
38
Press Menu two times, highlight Time Setup, and press OK.
Time Format—displays time in a 12- or 24-hour format, or UTC.
Time Zone—select a time zone from the list. If your time zone is
not on the list, select Other to
manually enter the UTC Offset.
If you are not certain what the
offset is between UTC and the
local time zone, enter incremental
offset values until the correct
local time appears. As you move
west of the Prime Meridian (0°
longitude) the offset is negative (-), and as you move east the offset
is positive (+).
Daylight Savings—turn on (Yes), off (No), or set to Automatic
(Auto) if it is available.
To restore these settings, press the Menu key, highlight Restore
Settings, and press OK.
Quest® 2 Owner’s Manual
Customizing Your Quest 2> Changing the Track Setup
Changing the Track Setup
As you travel, the Quest 2 automatically records your path in the
Track Log, creating an electronic “bread crumb” trail. This feature
can be enabled or disabled from the Track Setup page. By default,
it is enabled.
Press Menu two times, highlight Track Setup, and press OK.
Track Recording—select Enabled to record tracks or Disabled to
stop tracks from being recorded.
Wrap When Full—select On to allow new track points to replace
the oldest track points once the log is full. If set to Off, no new
tracks are added until the Track log is cleared.
Percentage Full—shows the percentage of track memory used.
Clear Track—clears all of the points of the track log.
To restore these settings, press the Menu key, highlight Restore
Settings, and press OK.
Record Interval—sets the interval at which track points are
recorded. With Auto, track points are recorded using a formula and
the setting you choose in the Resolution field.
Resolution—selects the frequency at which you want track points
to be recorded based on how you set Record Interval (above).
Higher resolutions cause the track log to fill up more quickly.
Quest® 2 Owner’s Manual39
Customizing Your Quest 2 > Customizing the Welcome Page and Viewing Software and Unit Information
Customizing the Welcome Page
You can customize the Welcome page that appears when you turn
on your Quest 2. Press MENU two times, highlight Welcome
Setup, and press OK. Use the on-screen keyboard to type in your
message and select Done. When you turn on the Quest 2 again,
your message appears.
Updating the Quest 2 Software
Use WebUpdater to update your Quest 2 software. Go to
www.garmin.com/products/webupdater/ to download the
WebUpdater program.
Default Welcome Page
Customized Welcome Page
To use the default Welcome page again, repeat the above process
and clear the text you entered previously.
Viewing Software and Unit Information
The About page shows the software version currently loaded in
the Quest 2. It also shows the unit ID number, which is used for
registration and identification purposes. Press Menu two times,
highlight About Quest, and press OK.
40
After downloading WebUpdater to your computer, connect your
Quest 2 to your computer, run WebUpdater, and follow the screen
prompts. After confirming that you want to perform an update,
WebUpdater automatically downloads the update and installs it on
your Quest 2.
If you register your Quest 2, you will receive notification of
software and map updates. To register your Quest 2, go to
www.garmin.com/registration/.
You can also download software updates from www.garmin.com/
products/quest2/. Click Software Updates. Click Download next
to the unit software. Read and agree to the terms. Click Download.
Select Run (or Open). Your software is updated.
Quest® 2 Owner’s Manual
Understanding GPS > The GPS Information Page
Understanding GPS
The Global Positioning System (GPS) is a satellite-based
navigation system made up of a network of 24 satellites placed
into orbit by the U.S. Department of Defense. GPS was originally
intended for military applications, but the government made the
system available for civilian use in the 1980s. GPS works in any
weather condition, anywhere in the world, 24 hours a day. There
are no subscription fees or setup charges to use GPS.
GPS satellites circle the earth twice a day in a very precise orbit
and transmit signal information to Earth. The GPS receiver in your
Quest 2 takes this information and uses triangulation to calculate
your exact location. Essentially, the GPS receiver compares the
time a signal was transmitted by a satellite with the time it was
received. The time difference tells the GPS receiver how far away
the satellite is. With distance measurements from a few more
satellites, the receiver can determine your location and display it on
the Map page.
A GPS receiver must be locked on to at least three satellites
to calculate a 2D location (latitude and longitude) and track
movement. With four or more satellites in view, the receiver can
determine your 3D location (latitude, longitude, and altitude).
After your location has been determined, the GPS unit can
calculate other information, such as speed, bearing, track, trip
distance, distance to destination, sunrise and sunset, and time.
WAAS is a system of satellites and ground stations that provide
GPS signal corrections, giving you even better position accuracy.
WAAS corrects for GPS signal errors caused by ionospheric
disturbances, timing, and satellite orbit errors, and it provides vital
integrity information regarding the health of each GPS satellite.
The GPS Information Page
The GPS Information page provides a visual reference of GPS
receiver functions, including current satellite coverage, receiver
status, and position accuracy. To access this page, press Menu,
highlight Settings, and press OK. From the Settings page,
highlight GPS Info and press OK.
GPS satellites are positioned throughout the sky. As soon as
you turn on your Quest 2, it attempts to acquire satellite signals.
The sky view area on the GPS Information page displays which
satellites are currently in your area.
Quest® 2 Owner’s Manual41
Understanding GPS > The GPS Information Page
A signal strength bar appears for each satellite in view; the
satellite’s number (1–33) appears to the left of each bar. The
progress of satellite acquisition is shown in three stages:
• No signal strength bar—the GPS receiver is looking for
the satellite indicated. The corresponding number on the sky
view is not highlighted.
• Hollow signal strength bar—the GPS receiver has found
the satellite and is collecting data. The corresponding
number on the sky view is not highlighted.
• Solid signal strength bar—the GPS receiver has collected
the necessary data and the satellite is ready for use. The
corresponding number on the sky view is highlighted.
Sky view
Satellites
Satellite
status bar
Signal
strength
bars
After a fix has been calculated, the Quest 2 updates your location
and ground speed by selecting and using the best satellites in view.
42
Sky View and Signal Strength Bars
The sky view and signal strength bars indicate which satellites are
currently visible and which satellites are being used to calculate
a position fix. The signal strength bars also indicate the quality of
each satellite signal.
The sky view provides a “bird’s eye” view of each satellite
position relative to your unit’s last known location. The outer circle
represents the horizon and shows cardinal heading references. The
inner circle represents an elevation of 45° above the horizon. Any
satellite depicted near the center is directly overhead.
You can set the sky view to Track Up
instead of North Up orientation. Track Up
causes the top of the sky view to align to
your current direction of travel. To change
to Track Up, press Menu while on the GPS
Info page. Then select Skyview Track Up.
Press Menu again and then select Skyview When the Sky View is
North Up to change the orientation back to shown in North Up, the
red circle indicates your
North Up.
direction of travel.
Quest® 2 Owner’s Manual
Understanding GPS > The GPS Information Page
Satellite Status Bar
As soon as the GPS receiver has collected the necessary data to
calculate a fix, the status bar indicates a position fix. The current
GPS status and the accuracy of the position fix can be found in
the satellite status bar located at the top of the page. The status bar
displays one of the following messages:
Searching for Satellites—the GPS receiver is looking for any
available satellites in view.
Locating Satellites—the GPS receiver is locating satellites and
determining which ones are visible at your location.
Acquiring Satellites—the GPS receiver is collecting data from
available satellites but has not collected enough data to calculate a
position fix.
Satellite status bar
Ready to Navigate—the Quest 2 is ready to navigate routes.
2D Navigation—at least three satellites with good geometry have
been found; a two-dimensional position fix (latitude and longitude)
is being calculated. You might need to enter your elevation if the
receiver only has a 2D fix. Displays “2D Differential” if you are
tracking one of the WAAS satellites.
3D Navigation—at least four satellites with good geometry have
been found; your location is now being calculated in latitude,
longitude, and elevation. Displays “3D Differential” if you are
tracking one of the WAAS satellites.
Lost Satellite Reception—the GPS receiver has temporarily lost
satellite reception.
Poor GPS Coverage—the GPS receiver is not tracking enough
satellites for a 2D or 3D fix due to bad satellite geometry or due to
a shaded antenna, which can be caused from very dense overhead
tress or tall buildings.
Receiver Not Usable—the Quest 2 is unusable, possibly due
to incorrect initialization or abnormal satellite conditions. Turn
the unit off and back on to reset and re-initialize the receiver if
necessary.
GPS is Off—the GPS receiver has been turned off and cannot be
used for navigation.
Quest® 2 Owner’s Manual43
Understanding GPS > The GPS Information Page
Poor Satellite Reception Menu
If the Quest 2 cannot establish a position fix after several minutes,
the Poor Satellite Reception menu appears. The menu might appear
when you first use your Quest 2 or during normal use if the antenna
is shaded or if the unit is used indoors.
The Poor Satellite Reception
menu gives you several
options when an insufficient
number of satellites is received
to determine a position fix.
From the Poor Satellite Reception menu, you can turn off GPS
when using the unit indoors, update your approximate location, or
continue to search for the satellites. Updating your approximate
location ensures that the Quest 2 is searching for the correct
satellites and is useful if you have traveled over 500 miles with the
unit turned off.
44
To select a new location:
1. Press the Menu key, highlight Settings, and press OK.
2. Highlight GPS Info and press OK to open the GPS
Information page.
3. Press Menu.
4. Highlight New Location and press OK.
5. A window appears with two options. Highlight either
Automatic or Use Map and press OK:
• Select Automatic to put the unit in AutoLocate mode
and begin searching the sky for satellites.
• Select Use Map to select your location on a map page.
Pan and zoom the map and use the map pointer to find
your approximate location. Then press OK.
These options appear when
you press Menu from the
GPS Info page.
Quest® 2 Owner’s Manual
Appendix > Quest 2 Shortcuts and Data Fields
Appendix
Quest 2 Shortcuts
•
•
•
•
•
•
•
•
Press and hold Find to navigate to your Home location.
Press and hold Menu to open the Route Options menu.
Press and hold OK to open the Where Am I? page.
Press Find two times to open the Recent Finds page.
Press Menu twice to open the Settings page.
Press Power to open the backlight illumination window.
Press zoom In or Out to scroll up or down a list.
Press POWER and In at the same time to shut off the
Quest 2 if it locks up.
Course—direction from your starting location to a destination.
(Appears only on the Compass page.)
Distance-Destination—distance to your destination.
Distance-Next—distance to your next turn.
Elevation—elevation of your current location.
Heading—current direction of travel. (Not available on the Trip
Information page.)
Location (lat/lon)—displays longitude and latitude of your current
location.
Location (selected)—displays your current location in the position
format you select in Units Setup page (see page 38).
Data Fields
Name-Destination—name of the destination. (Appears only on the
Compass page.)
Accuracy GPS—estimated GPS accuracy in feet or meters.
Name-Next—name of your next upcoming turn or maneuver.
(Appears only on the Compass page.)
The following data fields are available:
Arrive-Destination—estimated time of arrival at your destination.
Arrive-Next—estimated time of arrival at the next turn.
Odometer—running total of distance traveled. Unlike the Trip
Odometer, the odometer cannot be reset.
Bearing—compass direction from your location to your
destination. (Appears only on the Compass page.)
Off Course—distance left or right you are from the original course
(path of travel). (Appears only on the Compass page.)
Quest® 2 Owner’s Manual45
Appendix > Data Fields
Power (Battery)—battery power status.
Speed—current speed, displayed in miles or kilometers per hour.
(Not available on the Trip Information page.)
Speed-Maximum—maximum speed recorded since the Trip
Computer was last reset.
Speed-Moving Average—average speed of travel in motion since
the Trip Computer was last reset.
Speed-Overall Average—average speed of travel (including time
stopped) during the time the unit has been tracking your location.
Sunrise—time of today’s sunrise at the unit’s present location.
Sunset—time of today’s sunset at the unit’s present location.
Time of Day—current time.
Time to Destination—estimated time left until you reach your
destination.
Trip Time-Moving—length of time in motion since the Trip
Computer was last reset.
Trip Time-Stopped—length of time stopped (or stationary) since
the Trip Computer was last reset.
Trip Time-Total—total length of time that the unit has been
tracking your location since the Trip Computer was last reset. This
is always equal to Moving Time plus Stopped Time.
Turn—angle difference (in degrees) from the bearing to your
destination and your current line of travel. L means turn left; R
means turn right. (Appears only on the Compass page.)
Velocity Made Good—speed at which you are closing on a
destination along a desired course. Also referred to as the vector
velocity to your destination. (Appears only on the Compass page.)
Vertical Speed—rate of altitude gain/loss over time. (Appears only
on the Compass page.)
Time to Next—estimated time left until you reach the next turn.
To Course—direction of travel to get back on course. (Appears
only on the Compass page.)
Trip Odometer—running total of distance traveled since the Trip
Computer was last reset.
46
Quest® 2 Owner’s Manual
Appendix > Adding Maps to Your Quest 2
Adding Maps to Your Quest 2
You can purchase additional MapSource® maps from Garmin for
your Quest 2.
Purchasing Additional MapSource Maps
In order to unlock and use additional MapSource data, you need
your Unit ID number (see page 40) and serial number (see
page 51). After you unlock your map data, you can transfer it to
the Quest 2 using MapSource and your personal computer.
Note that the preloaded maps on your Quest 2 are protected and
cannot be erased. For example, if you add additional maps to your
Quest 2, you will not overwrite the original maps. If you load
additional maps to the Quest 2, these maps are not protected. The
additional maps will be overwritten each time you load new maps
to the unit.
Controlling Map Views on the Map Page
You can view a list of your map families on the MapSource
Info page.
Map families loaded
Individual maps loaded
The MapSource Info page lists the MapSource maps that are
loaded onto the unit. These are actually map families: each map
family may contain numerous smaller maps.
To see the smaller maps that make up the larger map family,
highlight the map family name and then press OK. A list of all
maps within that map family appears.
To disable a map, uncheck the box next to the map name. If the
maps loaded in your Quest 2 do not overlap, you should not need
to disable map families. If you load maps that cover the same area,
however, you may want to disable one of the map families so that
you can view detail from the other one.
To view the installed maps:
1. Press the Menu key, highlight Settings, and press OK.
2. Highlight Map Info and press OK. The MapSource Info
page opens.
Quest® 2 Owner’s Manual47
Appendix > Adding Maps to Your Quest 2
Changing Map Families when Finding Places
If your Quest 2 contains map families that have overlapping
information, you may need to specify a different map family. In
most cases the Quest 2 knows which map family to use for this
particular search.
To change the map family:
1. Press the Find key, highlight a category, and press OK.
2. Press the Menu key, highlight Select Map, and press OK.
A list of installed maps that contain searchable cities or
places appears.
3. Highlight the map family you want to use for the search
and press OK. The Quest 2 will then return a list of cities or
places only from this map family.
48
Quest® 2 Owner’s Manual
Appendix > Caring for the Quest 2 and Safe Mode
Caring for the Quest 2
The Quest 2 is constructed of high quality materials and does not
require user maintenance other than cleaning.
Cleaning the Case
Clean the unit’s outer casing (except for the screen) using a cloth
dampened with a mild detergent solution and then wipe dry.
Avoid chemical cleaners and solvents that may damage plastic
components.
Cleaning the Screen
Clean the screen using a soft, clean, lint-free cloth. You may use
water, isopropyl alcohol, or eyeglass cleaner if needed. To use these
cleaners, apply the liquid to the cloth and wipe the screen.
Storing the Quest 2
Do not store the Quest 2 where prolonged exposure to temperature
extremes may occur (such as in the trunk of a car), as permanent
damage may result.
Avoiding Theft
To avoid theft, take your Quest 2 with you or remove it from view
when you leave your vehicle.
Safe Mode
Safe Mode disables functions that require significant operator
attention and could distract the driver except for emergency
routing. Safe Mode turns on automatically when your vehicle
begins moving. While driving, if you press FIND, only the
Emergency & Government Services category is available. When
you come to a complete stop, all features are automatically
enabled. You cannot disable Safe Mode.
Read the safety information on pages iii–iv to learn how to use
your Quest 2 safely and responsibly.
Battery Temperature Warning
Your Quest 2 contains an internal lithium-ion battery, which can
store more energy than standard batteries. All batteries slowly lose
the amount of energy they can hold over time. To maximize battery
life, limit the unit’s prolonged exposure to excessive heat and direct
sunlight.
If Your Quest 2 Locks Up…
On rare occasions, your Quest 2 may freeze or lock up. In this case,
reset it by pressing the Power key and the In key at the same time.
The unit turns off. The unit will operate normally when you turn it
on again.
Quest® 2 Owner’s Manual49
Appendix > Specifications
Specifications
Physical Specifications
Size: 4.5" W x 2.2" H x 0.9" D (11.4 x 5.6 x 2.3 cm)
Weight: 5.5 oz (171 g)
Display: 1.5" W x 2.2" H, 256-color, high resolution, transflective
TFT (160 x 240 pixels), backlit. Compatible with polarized
sunglasses.
Case: Rugged, fully gasketed, water resistant to IEC 60529 IPX7
Antenna: Flip-up patch. MCX-type connector for remote antenna.
Temp. Range: 5° to 140° F (-15° to 60° C)
Keypad: Nine multifunction backlit keys
Performance Specifications
Receiver: WAAS-enabled, 12 parallel channel receiver
Acquisition Times1
Warm: Approximately 15 seconds
Cold: Approximately 45 seconds
AutoLocate®: Approximately 2 minutes
Update Rate: Once per second, continuous
GPS Accuracy
Position: < 15 meters (49 feet), 95% typical
Velocity: 0.05 m/s steady state
DGPS Accuracy
Position: 3–5 meters (10–16 feet), 95% typical
Velocity: 0.05 m/s steady state
50
Dynamics: Performs to specifications to 6 g’s
Interface: USB
Data Storage: Indefinite; no memory battery required
Map Storage: Internal; full map coverage
Power Specifications
Source: 12/24 VDC with car adapter up to 36 V, 115 VAC adapter,
internal lithium-ion battery
Battery Life2: Up to 20 hours (typical use)
Usage: 5 watts maximum at 13.8 VDC
Fuse: AGC/3AG - 1.0 Amp High breaking capacity, rated 1500 A
Features
Waypoints (Saved Locations): 500 with name and graphic symbol
Routes: Up to 50 stored
Track Log: 10,000 track log points
Warm = all data known; Cold = position, time and almanac known;
AutoLocate = almanac known, position and time unknown.
2
The lithium-ion battery loses capacity as its temperature decreases. Use of
backlight and tones also reduces your battery life.
1
Quest® 2 Owner’s Manual
Appendix > Product and Regulatory Information
Product and Regulatory Information
Product Registration
Help us better support you by completing our online registration
today! Connect to our Web site at www.garmin.com/registration/.
Use this area to record the serial number (8-digit number located on
the back of the Quest 2) in case your Quest 2 needs service. Keep
the original sales receipt, or a photocopy, in a safe place.
Serial Number: ___ ___ ___ ___ ___ ___ ___ __
Contact Information
If you have any problems with your Quest 2, contact your local
Toyota dealer for help.
Software License Agreement
BY USING THE QUEST 2, YOU AGREE TO BE BOUND BY
THE TERMS AND CONDITIONS OF THE FOLLOWING
SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS
AGREEMENT CAREFULLY.
Garmin grants you a limited license to use the software embedded
in this device (the “Software”) in binary executable form in the
normal operation of the product. Title, ownership rights, and
intellectual property rights in and to the Software remain with
Garmin.
You acknowledge that the Software is the property of Garmin and
is protected under the United States of America copyright laws
and international copyright treaties. You further acknowledge
that the structure, organization, and code of the Software are
valuable trade secrets of Garmin and that the Software in source
code form remains a valuable trade secret of Garmin. You agree
not to decompile, disassemble, modify, reverse assemble, reverse
engineer, or reduce to human readable form the Software or any
part thereof or create any derivative works based on the Software.
You agree not to export or re-export the Software to any country
in violation of the export control laws of the United States of
America.
FCC Compliance
The Quest 2 complies with Part 15 of the FCC interference limits
for Class B digital devices FOR HOME OR OFFICE USE. These
limits are designed to provide more reasonable protection against
harmful interference in a residential installation, and are more
stringent than “outdoor” requirements.
Quest® 2 Owner’s Manual51
Appendix > Product and Regulatory Information
Operation of this device is subject to the following conditions: (1)
This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
This equipment generates, uses, and can radiate radio
frequency energy and may cause harmful interference to radio
communications if not installed and used in accordance with the
instructions. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the
following measures:
The Quest 2 does not contain any user-serviceable parts. Repairs
should only be made by an authorized Garmin service center.
Unauthorized repairs or modifications could result in permanent
damage to the equipment, and void your warranty and your
authority to operate this device under Part 15 regulations.
Toyota Limited Warranty
See your Toyota dealer for warranty information.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
52
Quest® 2 Owner’s Manual
Index
Index
Symbols
2D Navigation 43
3D Navigation 43
A
acquiring satellites 43
adding mapping software 47
addresses, finding 10
antenna
external 1
positioning of flip-up 1
area tab 34
assign category 16
AutoZoom 34
avoid
area 26
road 25
road type 25
B
backlight 6, 35
battery icons 32
battery saver 36
battery temperature warning 49
bearing pointer 20
best route 37
C
calculate routes for 37
categories 16
city, finding 11
city tab 34
cleaning the Quest 2 49
clear track 39
color mode 34, 35
Compass page 20
course pointer 20
create a category 16
Current Route page 31
customizing 33
display setup 35
map setup 33
route setup 37
system setup 36
track setup 39
units setup 38
welcome page 40
D
data fields
Compass page 20
customizing 33
definitions 45
Map page 29
Trip Info page 32
datum 38
daylight savings 38
daytime color mode 35
delete
avoidance 26
category 16
recent finds 12
route 22
saved location 17
via point 24
detours 23
Directions to Me 9
display setup 35
E
edit a saved location 16
elevation 38
entering data 7
exits, finding 11
external power lost 36
F
faster time 37
FCC 51
finding places 8–13
addresses 10
cities 11
exits 11
intersections 10
My Locations 17
Recent Finds 12
Find key 6
Find menu 8
find near 9
frozen screen 49
G
GPS 41–44
mode 36
turn off/on 43
H
heading, units 38
hide above 34
Home Location 18
I
indoor use 5
intersections, finding 10
K
keyboard, on-screen 7
keypress tone 36
keys 6
L
layout tab 33
line tab 34
locating satellites 43
location format 38
locks up 49
lost satellite reception 43
M
magnetic variance 38
mapping software, adding 47
map card 27
map detail level 33
map info 47
Map page
controlling map views 47
customizing 33
learning how to use 27–29
map setup 33–34
maximum speed, resetting 32
Menu key 6
modifying routes 21
move around the map 28
My Locations 14–17. See
also saved location
finding 17
saving 14
N
navigational text (navtext) 27,
33
new location 44
Next Turn page 30
nighttime color mode 35
north up 33
Quest 2® Owner’s Manual53
Index
O
off road 37
OK key 6
on-screen keyboard 7
optimal via order 24
orientation 29, 33
overzoom 27
P
Page key 6
panning the map 28
percentage full 39
point tab 34
poor GPS coverage 43
poor satellite reception 44
Power key 6
R
ready to navigate 43
recalculating routes 23
receiver not usable 43
Recent Finds 12
record interval 39
resetting trip data, max
speed 32
reset the unit 49
restore settings
display 35
54
map setup 34
system setup 36, 37,
38, 39
reverse route 24
road lock 33
routes 21–26
deleting 22
detours 23
modifying 21
planning 21
preference 37
recalculating 23
saving 22
setup 37
via points 23
S
Safe Mode 49
satellite reception off 5
satellite status bar 43
saved location
categories 16
edit 16
searching for satellites 43
security code 5
select exit road 11
select map set 48
shortcuts 45
show map 9
signal strength bars 42
simulator mode 5
sky view 42
software version 40
Speak key 6
specifications 50
storage 49
street detail level 33
system setup 36
T
text language 36
text size 34
time zone 38
TracBack 19
track log 19
recording 39
setup 39
track up 33
trip data, resetting 32
Trip Information page 32
trip planning 13
turn pointer 33
V
vertical speed, units 38
via points
adding 23
arranging 24
deleting 24
optimal via order 24
view details 28
voice guidance 36
voice language 36
W
WAAS 36, 41
welcome page, customizing 40
wrap when full 39
Z
zoom 27
Zoom In key 6
Zoom Out key 6
U
units setup 38
unit ID, finding 40
use current location 21
use indoors 5
UTC 38
Quest 2® Owner’s Manual
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin Web site at www.garmin.com.
© Copyright 2006 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00675-00 Rev. A