Garmin Rino 130 Two-Way Radio User Manual

®
130
2-way radio & personal navigator
owner’s manual
®
© Copyright 2003 Garmin Ltd. or its subsidiaries
Garmin (Europe) Ltd.
Garmin Corporation
Unit 5, The Quadrangle,
No. 68, Jangshu 2nd Road,
Abbey Park Industrial Estate,
Shijr, Taipei County, Taiwan
Romsey, SO51 9AQ U.K.
Tel. 886/2.2642.9199
Fax. 886/2.2642.9099
Tel. 44/1794.519944
Fax. 44/1794.519222
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated,
downloaded, or stored in any storage medium for any purpose without prior written consent of Garmin. Garmin hereby grants permission to
download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed for personal use, provided that such
electronic or printed copy of this manual or revision must contain the complete text of this copyright notice and provided further that any
unauthorized commercial distribution of this manual is strictly prohibited.
Garmin International, Inc.
1200 E 151st Street,
Olathe, Kansas 66062 U.S.A.
Tel. 913/397.8200
Fax. 913/397.8282
Information in this manual is subject to change without notice. Garmin reserves the right to change or improve its products and to make
changes in the content without obligation to notify any person or organization of such changes. Visit the Garmin web site (www.Garmin.com)
for current updates and supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, AutoLocate®, Personal Navigator®, MapSource®, TracBack®, BlueChart®, and Rino® are registered trademarks of Garmin Ltd. or its
subsidiaries and may not be used without the express permission of Garmin.
December 2003
Part Number 190-00284-00 Rev. A
Printed in Taiwan
Thank you for choosing the Garmin Rino 130 (Radio Integrated with Navigation for the
Outdoors). To get the most from your new Rino 130, read through the Quick Start Guide first,
then this Owner’s Manual to understand all of the operating features.
The Quick Start Guide describes the process of navigating the Main Pages and the Option
Menus, along with some basic unit operations to familiarize you with your new Rino 130 right
out of the box. Read the Quick Start Guide first.
Introduction
About This Manual
Standard Package Contents:
1 Rino 130 Unit
This Owner’s Manual describes the Main Pages of the Rino 130 and their options in detail.
While the Owner’s Manual provides some direction on how to select and change items, its main
intention is to describe each Main Page, Option Menu, and feature in detail. This manual is
organized into the following sections:
1 Belt Clip
The Introduction section provides FCC, safety, warranty, and product registration information, as well as the Table of Contents.
1 PC Interface Cable
The Overview section provides basic information about the Rino 130.
The Reference section provides information on each of the six Main Pages, listed in the
same order as viewed on the unit. The section for each Page provides an overview that discusses the page, how it functions, and step-by-step instructions for using the page and its features.
1 Wrist Strap
1 Owner’s Manual
1 Quick Start Guide
Check to see that your package
includes the items listed above. If
any parts are missing, contact your
Garmin dealer immediately.
The Features section includes overview of some additional features and step-by-step
instructions for using the features.
The Appendix includes additional information about the Rino 130
The Index provides keywords and the pages on which they appear.
i
Introduction
Compliance, License, and
Warranty Information
FCC Compliance
The Rino 130 complies with Part 15 of the FCC regulations and with Canadian RSS-210
and ICES-003 for Class B digital devices. Operation of this device is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate radio frequency energy and may cause
harmful interference to radio communications if not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet that is on a different circuit than the receiver’s
circuit.
• Consult the dealer or an experienced radio/TV technician for help.
The Rino 130 does not contain any user-serviceable parts. Repairs should only be made
by an authorized Garmin service center. Unauthorized repairs or modifications could result in
permanent damage to the equipment and void your warranty and your authority to operate this
device.
ii
FCC Licensing Information
The Rino 130 two-way radio operates on General Mobile Radio Service (GMRS) frequencies
regulated by the Federal Communications Commission (FCC) in the United States. Operation
on the GMRS frequencies is subject to additional rules as specified in 47 CFR Part 95.
In order to transmit on GMRS frequencies, you are required to obtain a license from the
FCC. An individual 18 years of age or older, who is not a representative of a foreign government, is eligible to apply for a GMRS license. To apply for a GMRS license, you will need
FCC Form 605 (605 Main Form and Schedule F) and FCC Form 159. You can download the
application forms from the FCC web site at http://www.fcc.gov/Forms/. You can also request
them through the FCC forms hotline at 1-800-418-FORM (1-800-418-3676). You can file
Form 605 online at http://wireless.fcc.gov/uls/. A filing fee, which may change from time to time,
is associated with this application. For information on fees, see the FCC fee information web
page at http://wireless.fcc.gov/feesforms/index.html. General information may be found at http:
//wireless.fcc.gov/services/personal/generalmobile/.
Introduction
Compliance, License, and
Warranty Information
GMRS is not currently approved for use in Canada and some usage restrictions may apply
for use inside the U.S. near the Canadian border. For use in countries outside of the U.S.,
please check with that government for any restrictions of FRS or GMRS use.
For questions concerning the license application, contact the FCC at 1-888-Call-FCC (1888-225-5322)
iii
Introduction
Compliance, License, and
Warranty Information
Limited Warranty
This Garmin product is warranted to be free from defects in materials or workmanship for
one year from the date of purchase. Within this period, Garmin will at its sole option repair or
replace any components that fail in normal use. Such repairs or replacement will be made at
no charge to the customer for parts or labor, provided that the customer shall be responsible for
any transportation cost. This warranty does not cover failures due to abuse, misuse, accident or
unauthorized alteration or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING
ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT
OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR
INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states
do not allow the exclusion of incidental or consequential damages, so the above limitations may
not apply to you.
Garmin retains the exclusive right to repair or replace the unit or software or offer a full
refund of the purchase price at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE
AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.
iv
Products sold through online auctions are not eligible for rebates or other special offers from
Garmin. Online auction confirmations are not accepted for warranty verification. To obtain
warranty service, an original or copy of the sales receipt from the original retailer is required.
Garmin will not replace missing components from any package purchased through an online
auction.
Introduction
Compliance, License, and
Warranty Information
To obtain warranty service, contact your local Garmin authorized dealer. Or call Garmin
Customer Service at one of the numbers shown below, for shipping instructions and an RMA
tracking number. The unit should be securely packed with the tracking number clearly written
on the outside of the package. The unit should then be sent, freight charges prepaid, to any
Garmin warranty service station. A copy of the original sales receipt is required as the proof of
purchase for warranty repairs.
Garmin International, Inc.
1200 E 151st Street, Olathe, Kansas 66062 U.S.A.
Tel. 913/397.8200
Fax. 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ U.K.
Tel. 44/1794.519944
Fax. 44/1794.519222
The Garmin Rino 130 has no user-serviceable parts. Should you ever encounter a problem
with your unit, please take it to an authorized Garmin dealer for repairs.
The Rino 130 is fastened shut with screws. Any attempt to open the case to change or
modify the unit in any way will void your warranty and may result in permanent damage to the
equipment.
v
Introduction
Compliance, License, and
Warranty Information
Software License Agreement
BY USING THE Rino 130, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF
THE FOLLOWING SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT
CAREFULLY.
Garmin grants you a limited license to use the software embedded in this device (the “Software”) in
binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property rights in and to the Software remain in Garmin.
You acknowledge that the Software is the property of Garmin and is protected under the United
States of America copyright laws and international copyright treaties. You further acknowledge
that the structure, organization, and code of the Software are valuable trade secrets of Garmin and
that the Software in source code form remains a valuable trade secret of Garmin. You agree not to
decompile, disassemble, modify, reverse assemble, reverse engineer or reduce to human readable
form the Software or any part thereof or create any derivative works based on the Software. You
agree not to export or re-export the Software to any country in violation of the export control laws of
the United States of America.
Serial Number
Use this area to record the serial number (8-digit number
located in the battery compartment) in case it is lost,
stolen, or needs service. Be sure to keep your original
sales receipt in a safe place or attach a photocopy inside
the manual.
Serial Number:
vi
Product Registration
Help us better support you by completing our on-line registration today!
Have the serial number of your Rino 130 handy and connect to our web site
(www.Garmin.com). Look for the Product Registration link on the Home page. Also, be sure to
record your serial number in the area provided to the left.
NOTE: If you have previously registered a Garmin product purchase, we invite you to reregister using our NEW on-line system. Many services provided by our new product registration system are now being automated and re-registering your purchase ensures you the best
possible support from Garmin.
Warnings and Precautions
The GPS system is operated by the United States government, which is solely responsible for its
accuracy and maintenance. The system is subject to changes which could affect the accuracy and
performance of all GPS equipment. Although the Garmin Rino 130 is a precision electronic NAVigation AID (NAVAID), any NAVAID can be misused or misinterpreted and, therefore, become unsafe.
The electronic chart is an aid to navigation and is designed to facilitate the use of authorized government charts, not replace them. Only official government charts and notices to mariners contain all
information needed for safe navigation—and, as always, the user is responsible for their prudent use.
Use the Rino 130 at your own risk. To reduce the risk of unsafe operation, carefully review and
understand all aspects of this Owner’s Manual—and thoroughly practice operation using the Demo
mode prior to actual use. When in actual use, carefully compare indications from the Rino 130 to all
available navigation sources, including the information from other NAVAIDs, visual sightings, charts,
etc. For safety, always resolve any discrepancies before continuing navigation.
IMPORTANT: READ THIS INFORMATION BEFORE USING YOUR RINO.
Exposure to Radio Frequency Signals - Your wireless handheld radio is a low power radio
transmitter and receiver. When it is on, it receives and also sends out radio frequency (RF) signals.
In August 1996, The Federal Communications Commissions (FCC) adopted RF exposure guidelines
with safety levels for handheld wireless radios. Those guidelines are consistent with safety standards
previously set by both U.S. and international standards bodies: American National Standards
Institute (ANSI) IEEE. C95.1-1992; National Council on Radiation Protection and Measurements
(NCRP) Report 86; International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1996.
Those standards were based on comprehensive and periodic evaluations of the relevant scientific
literature. For example, over 130 scientists, engineers, and physicians from universities, government
health agencies, and industry reviewed the available body of research to develop the ANSI Standard
(C95.1). The design of your radio complies with the FCC guidelines (and those standards).
Introduction
Safety Information
MAP DATA INFORMATION: One of the goals of
Garmin is to provide customers with the most complete
and accurate cartography that is available to us at a
reasonable cost. We use a combination of governmental
and private data sources, which we identify (as required)
in product literature and copyright messages displayed
to the consumer. Virtually all data sources contain
inaccurate or incomplete data to some degree. This
is particularly true outside the United States, where
complete and accurate digital data is either not available
or prohibitively expensive.
CAUTION: IT IS THE USER’S RESPONSIBILITY
TO USE THIS PRODUCT PRUDENTLY. THIS
PRODUCT IS INTENDED TO BE USED ONLY
AS A NAVIGATIONAL AID AND MUST NOT BE
USED FOR ANY PURPOSE REQUIRING PRECISE
MEASUREMENT OF DIRECTION, DISTANCE,
LOCATION, OR TOPOGRAPHY.
vii
Introduction
Safety Information
For body-worn operation, this radio demonstrates compliance and meets the FCC RF exposure
guidelines when used with approved accessories supplied with or designed for this product. Use of
other accesssories may not ensure compliance with FCC RF exposure guidelines.
Antenna Care - Use only the supplied antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. Do not use any radio that has a
damaged antenna, because if it comes into contact with your skin, a minor burn can result.
Electronic Devices - Most modern electronic equipment is shielded from RF signals. However,
certain equipment may not be shielded against the RF signals from your wireless radio.
Pacemakers - The Health Industry Manufacturers Association recommends that a minimum separation of six inches (6”) be maintained between a handheld wireless radio and a pacemaker to avoid
potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers
should ALWAYS keep the radio more than six inches from their pacemaker when the radio is turned
on, should not carry the radio in a breast pocket, should use the ear opposite the pacemaker to minimize the potential for interference, and should turn the radio off immediately if you have any reason
to suspect that interference is taking place.
Hearing Aids - Some digital wireless radios may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices - If you use any other personal medical device, consult the manufacturer of
your device to determine if it is adequately shielded from external RF energy. Your physician may be
able to assist you in obtaining this information.
Turn your radio OFF in health care facilities when any regulations posted in these areas instruct
you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to
external RF energy.
Vehicles - RF signals may affect improperly installed or inadequately shielded electronic systems
in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You
viii
should also consult the manufacturer of any equipment that has been added to your vehicle.
Introduction
Posted Facilities - Turn your radio OFF in any facility where posted notices so require.
Commercial Aircraft - Many commercial airlines prohibit the use of FRS radios on board. Switch
OFF your radio before boarding an aircraft or check the airline rules.
Safety Information
Blasting Areas - To avoid interfering with blasting operations, turn your radio OFF when in a
“blasting area” or in areas posted: “Turn off two-way radio.” Obey all signs and instructions.
Potentially Explosive Atmospheres - Turn your radio OFF and do not remove your battery when
you are in any area with a potentially explosive atmosphere. Obey all signs and instructions. Sparks
from your battery in such areas could cause an explosion or fire resulting in bodily injury or even
death.
Areas with a potentially explosive atmosphere are often, but not always clearly marked. They
include fueling areas such as gasoline stations, below deck on boats, fuel or chemical transfer or storage facilities; vehicles using liquefied petroleum gas (such as propane or butane); areas where the air
contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you
would normally be advised to turn off your vehicle engine.
WARNING: This product, its packaging, and its components contain chemicals
known to the State of California to cause
cancer, birth defects, or reproductive harm.
This Notice is being provided in accordance
with California’s Proposition 65. If you
have any questions or would like additional
information, please refer to our web site at
http://www.garmin.com/prop65.
ix
Introduction
Table of Contents
Introduction.............................i
About This Manual ..................................i
Compliance, License, and Warranty Information ...................................................ii
FCC Compliance ............................... ii
FCC Licensing Information .............. iii
Limited Warranty ............................. iv
Software License Agreement ............. vi
Product Registration ......................... vi
Safety Information ............................... vii
Warnings and Precautions ............... vii
Overview ................................1
Rino 130 Overview .................................1
Getting to Know your Rino 130 .............. 1
Main Display Pages ........................... 2
Operating the Rino 130 ..................... 3
Status Bar Overview .......................... 4
Reference ...............................5
Radio Page..............................................5
Radio Page Overview ............................... 5
Initializing the Rino 130 .................... 5
Using ‘My ID’ and Symbol Fields....... 6
Setting the Channel and Squelch Code8
Scanning and Monitoring .................. 9
Radio Page Option Menu ...................... 12
Setup Radio ..................................... 12
Setup Tones ..................................... 14
x
Setup Scanlist .................................. 14
Use Weather Radio .......................... 15
Turn Radio/GPS On/Off ................... 16
Informational Picture ............................ 16
GPS Status....................................... 16
Radio Transmission Status .............. 16
Mark Waypoint’s indicators ............. 16
Using the Rino 130 Radio Features........ 18
Peer-to-Peer Positioning .................. 18
New Contact Page Overview ........... 18
Sending a Location .......................... 20
Map Page ..............................................22
Map Page Overview ............................... 22
Map Page Options ................................. 24
Using the Pan Map Option .............. 25
Programming the Data Fields .......... 26
Data Field Options .......................... 26
Setting up the Map .......................... 27
Measuring Distance ......................... 29
Navigation Page ...................................30
Navigation Page Overview ..................... 30
Using the Navigation Page ............... 31
Navigation Page Options ....................... 32
Using Sight ‘N Go............................ 33
Calibrating the Compass ................. 34
Turning the Compass On and Off .... 34
Altimeter Page......................................35
Altimeter Page Overview ....................... 35
Altimeter Page Options ......................... 36
Viewing Pressure/Elevation Plots ..... 37
Adjusting the Zoom Ranges ............. 37
Viewing Points ................................ 38
Resetting Data ................................. 38
Calibrating the Altimeter ................. 39
Programming Data Fields ................ 39
Trip Computer Page ..............................40
Trip Computer Page Overview .............. 40
Trip Computer Page Options ................. 40
Main Menu Page ...................................41
Main Menu Overview ............................ 41
Using the Main Menu ...................... 41
Main Menu Options .............................. 43
Page Sequence Setup ....................... 43
Features ................................44
Shortcuts Menu ....................................44
Shortcuts Menu Overview ..................... 44
Waypoints .............................................45
Waypoints ............................................. 45
Mark Waypoint Page ....................... 45
Creating Waypoints ......................... 46
Projecting a Waypoint ..................... 47
Editing a Waypoint ......................... 47
Find ‘N Go .............................................49
Find ‘N Go Menu .................................. 49
Finding a Waypoint......................... 50
Finding a Contact............................ 52
Finding a City ................................. 53
Finding an Exit ............................... 54
Finding a Point of Interest ............... 55
Finding an Address or Intersection .. 57
Finding a Last Found Place ............. 59
Weather Radio ......................................60
Using the Weather Radio ....................... 60
Send Note .............................................61
Sending a Note ...................................... 61
Goto .....................................................62
Using a Goto ......................................... 62
Routes Page ..........................................63
Routes Overview ................................... 63
Creating and Using a Route ............. 63
Editing a Route................................ 64
Adding or Editing from the Route Map
Page .......................................... 67
Navigating a Route .......................... 68
Stopping Navigation ........................ 69
Data Fields for the Route Page ......... 69
Tracks Page ...........................................70
Tracks Page Overview............................ 70
Using the TracBack Feature ............. 71
Setting up the Track Log.................. 72
Proximity Page .....................................73
Proximity Points .............................. 73
Satellite Page .......................................74
Introduction
Table of Contents
xi
Introduction
Table of Contents
xii
Satellite Page Overview ......................... 74
Skyview graphic .............................. 74
WAAS ............................................. 75
Satellite Strength ............................. 75
Satellite Page Options ............................ 76
Setup Pages ..........................................78
Setup Menu ........................................... 78
Time Setup Page .............................. 78
Units Setup Page ............................. 79
Display Setup Page .......................... 81
Heading Setup Page......................... 82
Interface Setup Page ........................ 83
System Setup Page........................... 85
Calendar ...............................................86
Using the Calendar .......................... 86
Alarm Clock ..........................................88
Using the Alarm Clock .................... 88
Calculator .............................................89
Using the Calculator ........................ 89
Stopwatch ............................................90
Using the Stopwatch ....................... 90
Stopwatch Lap Options ................... 90
Sun & Moon ..........................................91
Using the Sun & Moon Page ........... 91
Hunt & Fish ...........................................92
Using the Hunt & Fish Page ............ 92
Area Calculator.....................................93
Using the Area Calculator ................ 93
Games...................................................94
Games Menu ......................................... 94
Memory Race .................................. 94
Waypoint Bomber ........................... 95
Clothesline ...................................... 96
Assimilation .................................... 96
Beast Hunt ...................................... 96
Appendix ..............................97
FRS Explained .......................................97
FRS limitations ................................ 98
GMRS.............................................. 98
Specifications .......................................99
Accessories .........................................101
MapSource Setup ...............................102
Transferring MapSource Map Data. 102
GPS Troubleshooting Guide ................104
Radio Troubleshooting Guide .............105
Data Field Definitions.........................106
Interface Information .........................108
Interface Information .................... 108
Frequency Charts ................................109
FRS Frequency Chart .................... 109
Weather Radio Frequency Chart .... 109
GMRS Frequency Chart................. 110
Index ...................................111
GETTING TO KNOW YOUR RINO 130
The Rino 130 (Radio Integrated with Navigation for the Outdoors) is a 7.6 ounce, 12 channel GPS-enabled handheld device. It also has integrated radio functionality to provide two-way
communications for up to two miles using 14 FRS (Family Radio Service). The Rino 130 also
provides 8 high-performance GMRS (General Mobile Radio Service) channels and 8 GMRS
repeater channels (US versions only) for up to five miles. On Rino 130 units sold in Canada,
GMRS is not approved for use by the Canadian government and this feature is disabled.
Overview
Rino 130 Overview
You can keep track of up to 50 contacts from Rino users. The Rino 130 can store up to
500 waypoints with a 10-character name and graphic symbol. The active track log stores up to
10,000 points and allows you to save up to 20 tracks with 250 points per track. The Rino 130
has seven buttons located on the unit that allow the user to quickly access all of the unit’s functions. The Rino 130 has a 160 X 160 pixel, 4-level gray monochrome display for easy viewing.
The unit contains built-in cartography of a North American basemap that includes Interstate
and State Highways and Exit Information. Using MapSource, Garmin’s map data software (not
included), the Rino 130 could display up to 24 MB of a variety of different map information.
We currently offer several mapping options that are compatible with the Rino 130 including
our MetroGuide, Topo, Fishing Hot Spots, and BlueChart data. Check your local dealer or the
Garmin web site (www.Garmin.com) for a complete listing of MapSource products.
Garmin designed your Rino 130 with the you, the user, in mind. The Rino 130 is waterproof to IPX7 standards and is rugged enough to endure the most trying use. Garmin’s friendly
user interface allows you to start navigating with your new GPS in no time. Your Rino 130 can
provide one more critical benefit: peace of mind. With your Rino 130 you know where you
are, where you’ve been, and where you’re going. And since you’ll always know the way back
home, you can concentrate on what you set out to do; explore the great outdoors.
1
Overview
Main Display Pages
All of the information you need to operate the Rino 130 can be found on six default main
pages (or display screens). Simply press and release the PAGE button to cycle through the
Radio Page, Map Page, Navigation Page, Altimeter Page, Trip Computer, and Main Menu Page.
You can also access the Main Pages by pressing the on-screen Main Page button
. Customize the Main Page sequence through the Main Menu (see page 43).
2
Radio Page
Map Page
Navigation Page
Main Menu
Trip Computer
Altimeter Page
Operating the Rino 130
For best results, you should initialize the GPS receiver in your Rino 130 unit before you use
it the first time. See page 5 for instructions on initializing the unit. For most accurate results,
the compass and altimeter should also be calibrated. Refer to the Calibrating the Compass and
Calibrating the Altimeter sections for complete information.
Overview
Rino 130 Overview
The Rino 130 is programmed to provide “pop-up” messages concerning operational characteristics and conditions. Press the THUMB STICK IN to acknowledge a message and return to
the current feature.
To use the THUMB STICK:
•
Press IN to enter highlighted options and to confirm messages
•
Move UP, DOWN, RIGHT or LEFT to move through lists, highlight fields, on-screen buttons,
icons, enter data, or move the map panning arrow
•
Press IN and hold to display Shortcuts Menu.
Hold the Page button to
release the keylock.
To use the page Option Menu:
1. Highlight the Option Menu on-screen button
press the THUMB STICK IN to open the menu.
at the top of the display screen and then
2. Highlight the desired menu option and press the THUMB STICK IN to activate the option.
3. To close without making a selection, move the THUMB STICK to the RIGHT.
To lock/unlock the buttons:
1. Press and hold the THUMB STICK IN to access the Shortcuts Menu. Highlight ‘Enable
Keylock’ and press the THUMB STICK IN. The TALK button is not locked.
2. To unlock, press and hold the PAGE button until ‘Keylock Disabled’ is displayed (about 5
seconds).
3
Overview
Rino 130 Overview
Main Page Menu
button/ Exit button
Option Menu button
Status Bar
Status Bar Overview
The Status Bar at the top of the screen displays on all the available Main Pages. As you
move around any of the Main Pages, the current page’s title briefly displays (3 seconds) and
then is replaced by the Status Bar. The current settings and operational icons on the Status Bar
are displayed as you operate the unit. The available icons are:
Battery Full (Each bar represents 1/4 charge)
Battery 1/2 charge
Battery Empty
Using External Power
Receiving Radio signal
Transmitting Radio signal
Backlight On
Radio On
Peer-To-Peer On/Location Ready to Send
Keylock On
Alarm Clock On
GPS On and Position Ready
GPS On, Position Not Ready
Compass On (Press and hold the ZOOM key to turn the compass on/off)
Weather Alert On
4
RADIO PAGE OVERVIEW
The Radio Page is the first of the default Main Pages. This page provides the user interface
for FRS (Family Radio Service) and GMRS (General Mobile Radio Service) radio operations.
Garmin Rino units work with 3rd party FRS/GMRS radios, provided the other radios use standard FRS/GMRS frequencies. To take full advantage of the Rino features, communicate with
other Rino users.
Reference
Radio Page
The Radio Page also provides access to the Weather Radio, which provides a constant
update of current weather conditions. The Weather Alert feature further enhances the Weather
Radio by automatically notifying you of any weather alerts, even when the Weather Radio is not
is use and the FRS/GMRS radio is in use! These features are helpful while outdoors or planning
a road trip. Also use this page to control and setup the radio, view current settings and see
informational graphics of the unit’s operation.
Initializing the Rino 130
To take full advantage of all of the Rino 130 features, the GPS receiver must be initialized.
The initialization process allows the Rino 130 to receive and store satellite information, and
begin using the satellites for navigation. Initialization is automatic, should only take a few
minutes, and only needs to be done the first time the unit is used.
Radio Page
To initialize the unit:
1. Take the Rino 130 outside where it has an unobstructed view of the sky and turn it on.
2. The unit begins to search for satellite signals. “Tracking Satellites” is displayed while the
unit is initializing.
3. Initialization should take no more than five minutes. When the GPS is initialized and ready
for navigation, the message “3D Accuracy” is displayed on the Radio Page.
5
Reference
Radio Page
Using ‘My ID’ and Symbol Fields
The ‘My ID’ field allows you to enter a name and symbol that appears on other Rino units as
you communicate with them. You may enter a name using a combination of up to 10 letters,
numbers, or spaces. The Symbol field allows you to choose a face icon from a list to further
personalize your ID.
To enter a name:
1. Using the THUMB STICK, highlight the ‘My ID’ field. Press the THUMB STICK IN to
activate the field and display the keyboard.
‘My ID’ Field
2. Move the THUMB STICK UP, DOWN, LEFT, or RIGHT to highlight the ‘Clear’ field, then press
the THUMB STICK IN to clear the default ‘Name’ ID.
Entering a name with
the on-screen keyboard
Symbol
3. To enter a new ID, use the THUMB STICK to move the cursor to the desired character
(letter, number, or a space). Press the THUMB STICK IN to select that highlighted character.
Choose ‘Back’ to delete the character to the left of the cursor. You may enter up to 10
characters for your ID.
4. When you have entered your new ID, use the THUMB STICK to highlight ‘OK’ and then
press the THUMB STICK IN.
6
To change the user symbol:
1. Using the THUMB STICK, highlight the face symbol to the right of the ‘My ID’ field. Press
the THUMB STICK IN to show a list of available face icons.
2. Move the THUMB STICK UP or DOWN to scroll through the selections. Because not all the
selections can fit in the window, a slider bar on the right side indicates your current position
in the list.
Reference
Radio Page
TIP: Hold the THUMB STICK UP or DOWN to scroll through the list more quickly.
Once you reach the end of the list, you can ‘wrap’ back to the top or bottom by
releasing the THUMB STICK then pressing in the same direction again. This same
method may also be used on other selection windows.
3. Once you have highlighted the desired icon, press the THUMB STICK IN.
Changing the user symbol
7
Reference
Radio Page
Setting the Channel and Squelch Code
The Rino 130 has a total of 22 channels (not including GMRS repeater channels) and 38
squelch codes to select from using the ‘Channel’ and ‘Code’ fields. Channels 1–14 are for FRS,
15–22 are for GMRS (disabled by default) 15R–22R are for GMRS repeater channels (disabled
by default). To communicate with other Rino and FRS/GMRS users, you must be on the same
channel and squelch code. Garmin Rino units work with 3rd party FRS/GMRS radios, provided
the other radios use standard FRS/GMRS frequencies. A chart of Rino frequencies may be
found in the Appendix.
Squelch codes allow you to hear calls from only specific persons. Thirty-eight (38) Squelch
Codes (called Continuous Tone Coded Squelch System or CTCSS) allow your Rino 130 to
ignore unwanted calls from other persons using the same channel. Simply select the same
squelch code (number) as selected by the other person(s) with which you will communicate.
NOTE: Squelch codes do not cause your conversation to be private. They only allow
Select from FRS 1–14,
GMRS 15–22 (with
GMRS enabled), and
15R–22R GMRS
repeater channels (with
GMRS and Repaeter
Channels enabled).
8
you to filter out other users on the same channel, so you only hear the radios you
want to hear. Squelch Codes are not a scrambling system!
Setting the squelch code to 0 (squelch code off) allows you to hear all activity on the selected channel, but you must be set to the same squelch code as the other person(s) to transmit
back. See the Appendix for a table listing all of the 38 Squelch Codes and their frequencies.
As you change the main channels, the Rino 130 remembers the last channel/squelch code
combination that you were using. For example, you may set the unit channel to 5 and squelch
code to 21, then change the main channel to 8 and squelch code to 2. If you change the channel back to 5, the squelch code changes back to its previous setting of 21. See the Appendix for
more information on FRS/GMRS and its operational aspects.
To change the Channel and/or Squelch Code:
1. Using the THUMB STICK, highlight the ‘Channel’ or ‘Code’ field and then press the THUMB
STICK IN to show a list of available channels/squelch codes.
2. Move the THUMB STICK UP or DOWN to scroll through the selections. Because not all the
items fit in the window, a slider bar on the right side indicates your current position in the
list.
Reference
Radio Page
3. Once you have highlighted the desired selection, press the THUMB STICK IN.
Scanning and Monitoring
The ‘Scan’ option allows you to scan through the available channels for voice activity. As
the unit scans and receives a signal (or if you transmit), it stops on that channel/squelch code
for a few seconds, then continues scanning. When the Rino 130 is scanning and it receives an
incoming signal, the Rino 130 automatically decodes the Squelch Code used by the incoming
signal. The Rino 130 then uses that Squelch Code when it transmits back to that unit.
You may use the Set Scanlist option to pick which channels/squelch codes to scan. Scanning through the all the channels can take time: Selecting only specific channels/squelch codes
decreases the scan time and helps prevent the chances of missing a transmission. The Scanlist
also has Option Menu
choices to ‘Scan Current Codes’ or ‘Scan All Codes’. Choosing ‘Scan
Current Codes’ scans only the Channel and Squelch Code combination in memory.
Choose from 38 squelch
codes. Setting the unit to
zero will allow you to hear
all transmissions on that
channel, but you must be
on the same squelch code to
radio back.
9
Reference
Radio Page
The ‘Monitor’ option lets you listen to a single channel for any activity, including static and
weak voice signals. The Rino series automatically squelches a frequency to filter out unwanted
noise. Using the Monitor option temporarily turns off the automatic squelch, allowing you to
hear the open channel. If you see a broken transmission symbol (see page 17), there is activity
on your selected channel, but the incoming signal does not match the Squelch Code your unit
is using. You may choose to monitor a channel if you wish to hear all the activity on a channel.
To scan or monitor a channel(s):
1. Using the THUMB STICK, highlight the ‘Scan’ or ‘Monitor’ button and then press the
THUMB STICK IN. ‘Scan’ starts searching through the available channels. ‘Monitor’ opens
the channel to listen to any radio transmissions on that channel.
2. To stop using either option, highlight the button with the THUMB STICK and press IN.
The Code field is blank
when the unit is scanning or
monitoring channels.
10
Reference
To setup a Scanlist:
1. Using the THUMB STICK, highlight the Option Menu on-screen button
Highlight ‘Setup Scanlist’ and press the THUMB STICK IN.
and press IN.
2. To add/remove a channel from the list, highlight the channel and press the THUMB STICK
IN to add/remove the check mark in front of the name. Only channels that are checked will
be scanned.
Radio Page
3. To select all channels or clear all channels, highlight either the ‘Select All’ or ‘Clear All’
buttons and press the THUMB STICK IN.
4. To ‘Scan Current Codes’, highlight the Option Menu
and press the THUMB STICK IN.
Choose the desired setting and press the THUMB STICK IN.
The Radio Page Option Menu provides the following: Setup Radio, Setup Tones, Setup
Scanlist, Use Weather Radio/Use FRS/GMRS Radio, Turn Radio Off/On, Turn GPS Off/
On, and Enable Weather Alert. Refer to the following pages for explanations of each item in
the Radio Page Option Menu.
Scanlist Page
11
Reference
Radio Page
RADIO PAGE OPTION MENU
The Radio Page Option Menu
allows you to customize aspects of your Rino 130, such
as setting up the radio, programming call and ring tones, and setting up a scanlist.
Setup Radio
The ‘Setup Radio’ option displays the Radio Setup Page. This page determines how the
radio functions and enables you to adjust the radio operation to your needs. The following
options are available:
Radio Page
Option Menu
Send Location - Enables/disables the peer-to-peer positioning feature. See the Peer-to-Peer
section for more on this feature.
Allow Polling - Enables/disables you Rino 130’s ability to respond to a poll from another Rino.
VOX Level - Controls the sensitivity level of any Voice Operated Transmission (VOX) accessory.
VOX accessories allow you to use the unit hands-free. A lower VOX setting is recommended
for quiet environments while a higher VOX setting should be used in noisy environments.
Setting the VOX level to 5 is recommended for most environments, but it may be necessary to
adjust the level to achieve the desired voice trigger level. You will hear yourself talking in the
headset when transmitting successfully using VOX.
Setup Radio Page
Scramble - Adds a level of security to your conversations with other Rino 120 or 130 users
only. When On, the voice transmission sounds garbled to other non-scrambled Rino units, as
well as other 3rd party radios.
NOTE: When Scramble is set to On, in order for peer-to-peer and Send Location
features to work, the receiving radio must have Scramble enabled also.
12
GMRS Radio - Use this option to turn On/Off GMRS channels 15–22. Peer-to-peer positioning is not available on GMRS channels. See the FCC Licensing Information section and the
Appendix for more information on using GMRS channels.
Repeater Channel - Use this option to turn On/Off GMRS repeater channels 15R–22R. This
option is only available when GMRS is enabled.
Reference
Radio Page
Headset Type - Allows you to choose which accessory headset or microphone you are using
with the unit, or have the unit automatically detect the type. If you use more than one type
of headset or microphone, you need to set the unit to ‘Ask When Detected’ before changing
accessories.
NOTE: If the headset has a PTT (Push to Talk) button, it must be pressed for the unit
to detect the headset.
Microphone Sensitivity - Allows you to set the sensitivity of the internal microphone and the
sensitivity of a headset microphone.
You must obtain a license to
operate on GMRS channels
15–22.
13
Reference
Radio Page
Setup Tones
Call Tone - When the CALL button is pressed, an attention tone is transmitted. This option
allows you to choose one of ten tones.
Roger Tone - When the TALK button is released, a tone is sent to signify the end of the transmission. This option allows you to choose one of four tones, or set the tone to ‘Off’.
Ring Tone - When an incoming transmission is received, an attention tone will sound. This
option allows you to choose one of ten tones or set the tone to Off. The Ring tone will not
sound again until there has been 45 seconds of radio inactivity.
Setup Tones Page
Vibrate - Choose from ‘On’ or ‘Off’ to have the unit vibrate when an incoming transmission is
received. Once received, the unit will not vibrate again until there has been 45 seconds of radio
inactivity.
On/Off Tone - Enable or disable the tone the unit makes when it is turned on and off.
Message Tone - Choose from ‘On’ or ‘Off’ to have the unit emit a tone when a message or note
is received.
Setup Scanlist
Refer to Scanning and Monitoring for complete information about this feature and the options
in this page.
Setup Scanlist Page
14
Use Weather Radio
The Weather Radio provides a constant update of the weather conditions, which is helpful
while outdoors or planning a road trip. The Weather Alert further enhances the Weather Radio
by breaking into FRS/GMRS transmissions and automatically broadcasting any weather alerts.
Reference
Radio Page
Select the Radio Page Option Menu button
. Press the THUMB STICK IN when ‘Use
Weather Radio’ is highlighted to turn on the weather radio. You can also access the Weather
Radio through the Shortcuts Menu.
When the Weather Radio is on, a tower emitting signals is shown in the informational picture on the Radio Page, as shown to the right. The FRS/GMRS radio cannot be used when the
Weather Radio is on. Also, you cannot scan or monitor FRS/GMRS channels when the Weather
Radio is in use. The audio is unmuted when the Weather Radio is on to be able to listen to
weather broadcasts.
Radio Page with
Weather Radio On
Change the Weather Radio channel in the same manner as changing the FRS/GMRS radio
channel. There are seven Weather Radio channels (1 through 7) available.
When the Weather Radio is on, ‘Enable Weather Alert’ is added at the bottom of the Option
Menu. Press the THUMB STICK IN when ‘Enable Weather Alert’ is highlighted to turn the
feature on. You can then turn the Weather Radio off and continue normal FRS/GMRS radio operations. When a Weather Alert tone is detected, the Rino 130 will break into any FRS/GMRS
transmission to automatically turn on the Weather Radio and broadcast the Weather Alert.
The volume changes to 4/3 the maximum when a Weather Alert is broadcast. Select ‘Disable
Weather Alert’ to turn off this feature.
To turn the weather radio off, press the THUMB STICK IN when ‘Use FRS/GMRS Radio’ is
highlighted. This switches the Rino 130 back over to the FRS/GMRS radio operation.
Changing the Weather
Radio Channel
15
Reference
Radio Page
Turn Radio/GPS On/Off
Press the THUMB STICK IN on either of these two options to toggle them from on to off.
For example, to turn GPS Off, press the THUMB STICK IN when ‘Turn GPS Off’ is highlighted.
INFORMATIONAL PICTURE
The Informational Picture on the bottom half of the Radio Page features Garmin’s Mr. Mark
Waypoint showing current GPS and radio status, and radio actions. As you operate the unit,
the graphics change depending on what actions you are taking and the unit settings.
GPS Status
Four satellites are shown on at the top of the picture along with descriptive text to indicate
GPS reception status. As the unit collects satellite information, the satellite symbols flash alternately until all four are steady to indicate a 3D position fix. The more satellites that are steady,
the better your position fix.
Informational Picture
showing Mr. Mark
Waypoint
Informational Picture Legend
Radio in Mark’s hand = radio is ready to use.
Flag in his other hand = unit ready to transmit its position
(GPS must be On to use this feature.)
Radio waves around Mark’s radio = you are transmitting
Raised flag in his hand = peer-to-peer transmission is sent
Flag on top of the hill = a position was received
16
Radio Transmission Status
As radio signals come in, signal wave symbols display to the left of Mark Waypoint.
Fragmented (or broken) signal symbols are shown to indicate activity on that channel. Audio
remains muted because the incoming signal does not match the squelch code your unit is set to.
Mark Waypoint’s indicators
The Mark Waypoint figure displays several different icons, depending on what you are doing. See the following illustrations for more information.
Reference
GPS and FRS/GMRS Radio On;
Ready to transmit Position
GPS and Weather Radio On
(FRS/GMRS Radio Off)
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Transmitting on FRS
GPS and FRS/GMRS Radio On;
Position not ready;
Transmitting on GMRS
GPS and FRS/GMRS Radio On;
Position transmitted
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Receiving transmission
Radio Page
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Activity on channel.
GPS and FRS/GMRS Radio On;
Ready to transmit Position;
Position received from other
Rino user
GPS Off; FRS/GMRS Radio On;
Position sending not available
GPS On; FRS/GMRS Radio Off;
GPS operation only
17
Reference
Radio Page
Name and
Symbol
Contact
Information
Field
USING THE RINO 130 RADIO FEATURES
Your Rino 130 unit provides many features to enhance your radio experience, such as transmitting your location or any location and receiving contact information. This section reviews
some of the advanced radio features. Refer to the Features section for information on all of the
features of the Rino 130.
Peer-to-Peer Positioning
The Rino 130’s most unique feature is being able to send its location to another Rino, which
is called Peer-to-Peer positioning. With peer-to-peer positioning enabled (see the Setup Radio
section) and you have a GPS position (see page 5 and 74-77), whenever you press and release
either the CALL button or the TALK button, the Rino 130 automatically sends out its location.
This information is available to all other Rino users that are monitoring the same channel and
squelch code. This feature allows you to track the movement of other Rino users and even
navigate to their location. Locations may only be sent once every 30 seconds due to FCC
restrictions. Your Rino 130 can respond to polling requests from other unit more frequently.
To transmit your location to other Rino users:
1. Enable ‘Send Location’ (see the Setup Radio section).
New Contact Page
2. Press and release either the TALK or CALL button. A flag on the top Status Bar or in Mark’s
hand indicates the unit is ready to transmit its position.
New Contact Page Overview
The first time that a signal is received from another Rino user, a ‘New Contact’ page is
displayed. From the New Contact page you can show their location on your ‘Map’, ‘Goto’ their
location, or add them to your contact list (select ‘OK’). Press PAGE to ignore this contact.
18
The Rino 130 can manage up to 50 contacts at any time. Each time that you receive a signal
from a contact, your map is updated showing their new position. A Track Log of their movement is created and shown on your map (see the Track Logs section). After a contact has been
established, a “<contact name> Updated” message briefly appears at the bottom of your display
each time the contact updates.
All contacts are listed on a Contact List Page and also displayed in the Contact Bar on the
Map Page (see the Map Page section). Contacts behave like waypoints and count towards the
500 maximum waypoint total. If the contact did not have a GPS location on the last transmission, a ? mark appears below the flag. To view the contact details (such as Direction, Elevation,
Timestamp, Location, and Notes that have up to 30 characters), highlight the details field and
press LEFT or RIGHT on the THUMB STICK to change to the next data field.
To accept a new contact:
1. When a new contact is received, the New Contact page automatically appears.
2. Highlight ‘OK’ and press the THUMB STICK IN. If you do not select OK, the contact is not
saved.
Reference
Radio Page
Press LEFT or RIGHT on
the THUMB STICK to
view different contact data.
Contact Bar
To review a contact and contact details:
1. From the Map Page, highlight the desired contact of the Contact Bar and press the THUMB
STICK IN. As you highlight the contacts on the Contact Bar, the Map page centers the map
on that contact and display its name, direction and distance near the top of the screen.
Or
1. Press the THUMB STICK IN and hold it until the Shortcuts Menu is displayed. Highlight
‘Find ‘N Go’ and press the THUMB STICK IN.
2. Highlight ‘Contacts’ and press the THUMB STICK IN.
3. From the Contacts List, select the desired contact and press the THUMB STICK IN.
Contacts also show on the Map
Page. Highlight the contact and
the map centers on their last
position.
19
Reference
Radio Page
To change contact details:
1. The Elevation, Position and Note fields may be manually edited. Select the desired field and
press the THUMB STICK IN.
2. For Notes, highlight ‘Edit’ and press IN to start entering data, up to 30 characters. For other
fields, highlight the field and press the THUMB STICK IN to start changing the data.
3. Highlight ‘OK’ and press IN when done.
To view a contact on the Map Page:
1. From the Contact Review Page, highlight ‘Map’ and press the THUMB STICK IN.
2. Press the PAGE button when done to return to the Contact Review Page.
To send a location, highlight
the Option Menu from the
Waypoint Review Page and
press IN.
20
Sending a Location
Another feature is the ability to send a specific location to other Rino users. This comes in
handy when you are trying to round-up the group or you just want to meet at a specific location. You may send any point found from the Find ‘N Go menu. If the unit needs to wait until
30 seconds have elapsed since the last position transmission, a “Waiting to send location...”
message appears until the unit is able to transmit. If a location is sent more than once, a number is automatically added to the end of the name (for example: CAMP, CAMP 1, CAMP 2, etc.).
Reference
To send a location:
1. Press the THUMB STICK IN and hold it until the Shortcuts Menu is displayed.
2. Highlight ‘Find ‘N’ Go’ and press the THUMB STICK IN.
3. Highlight the desired category and press the THUMB STICK IN. ( For the Contacts List,
select the desired contact and press the THUMB STICK IN.)
Radio Page
4. Depending on which category you select, highlight the desired item and press the THUMB
STICK IN to display the Information page for that item.
5. From the Information Page, highlight the Option Menu
THUMB STICK IN.
in the upper right and press the
6. Highlight ‘Send Location’ and press IN again. The unit now sends the point to the other
Rino users on your channel/squelch code. If using the Scramble feature, receiving radios
must also have Scramble enabled.
Choose ‘Send Location’ and
press IN.
21
Reference
MAP PAGE OVERVIEW
Map Page
The Map Page displays your present position and direction of movement using a triangular
‘Position Icon’ that is centered on the map. As you travel the map display leaves a “trail” (track
log) of your movements.
Status Bar
Option Menu and Main
Page Menu Buttons
The map displays geographic details such as rivers, lakes, highways, and towns. The map
can display a higher level of detail than the basemap provided with the unit (i.e. residential
streets, parks, etc.), if Garmin MapSource data has been downloaded to the unit using a CDROM mapping program. When using MapSource data, the word ‘mapsource’ displays below
the map scale whenever you zoom in to view map details.
On the right side of the Map Page, you can choose to show either the Contact Bar, Data
Fields, or only the Map. As you highlight the contacts on the Contact Bar, the Map page centers the map on that contact and displays its name, direction, and distance.
Map Scale
Contact Bar
Position Icon
In many instances the map displays an ‘Accuracy Circle’ surrounding the ‘Position Icon’.
The Rino 130 uses both map resolution and GPS accuracy in defining your location to a point
within the circle. The smaller the circle, the more accurate your location.
When using the ‘Pan Map’ feature, a small outline arrow (Map Pointer) can be moved about
the page to highlight and identify map items or to scroll the map to view areas not shown on
the display screen.
Accuracy Circle
22
Panning Arrow
(Map Pointer)
Four optional Data fields on the right side of the page can be programmed to provide a
variety of travel and navigation information.
To view a Contact from the Map Page:
Reference
1. Highlight the Contact icon using the THUMB STICK. As you highlight the contacts on
the Contact Bar, the Map page centers the map on that contact and displays its name,
direction, and distance near the top of the screen.
Map Page
2. Press the THUMB STICK IN to view the details of the Contact.
3. Press the THUMB STICK to the LEFT or RIGHT to re-center the map on your current
position.
The scale can be changed from 20 feet to 500 miles. A lower zoom scale displays less area
but more map detail, while a higher zoom scale shows you a larger area with less map detail.
The THUMB STICK and Z (ZOOM) button on the front right of the unit allow you to zoom in
and out on the map. Press the Z (ZOOM) button from any page (other than the Map Page) to
open the Map Page.
Press UP to Zoom Out
To change scales on the Map Page:
Map Page with Data
Fields
1. Press the Z (ZOOM) button to open the Zoom window.
2. Use the THUMB STICK and Z (ZOOM) button to change the
map scale in order to show more map area with less detail or
less map area with more detail.
Press and hold UP or DOWN on the THUMB STICK to zoom
the map scale rapidly. Press the THUMB STICK IN or to any
direction to close the Zoom window.
Press DOWN to Zoom In
The map scale in the lower left hand side of the display is shown in units of measurement
selected in the ‘Units’ field of the Unit Setup Page (accessed through the Main Menu Setup
Page). If you zoom in so far that the resolution of the map data is exceeded and the appearance
of the map is no longer accurate, the word, “overzoom” displays just below the map scale.
Map Page with
Contact Bar
23
Reference
Map Page
MAP PAGE OPTIONS
Map Page options allow a variety of operating and custom features for your Rino 130. The
Map Page options are: Highlight an option then press the THUMB STICK IN to select.
Pan Map - Allows you to move the Panning Arrow (Map Pointer) about on the map. Refer to
the Using the Pan Map Option section for complete instructions.
Stop Navigation - Quits navigation of a Goto, Route or Track in progress. When you are not
navigating to a destination, the ‘Stop Navigation’ option is “grayed out” and is non-functional.
Show... - Allows you to choose to show either the Contact Bar, four programmable Data Fields or show the Map Only. Choosing either Contact Bar
or Data Fields reduces the map area.
Setup Map - Displays the Setup Map Pages, which allow you to tailor the
map to your requirements such as changing text size, map orientation, and
map detail. Refer to the Setting up the Map section for complete instructions.
Map Page Option Menu
When you are not navigating to a
destination, ‘Stop Navigation’ is
displayed in gray..
24
‘Show..’ allows you
choose the layout of the
Map Page.
Measure Distance - Displays the distance from one point on the map to another.
Restore Defaults - Returns the Map Page to the original factory settings (defaults).
Using the Pan Map Option
The Map Page pan function allows you to display an arrow used to point at and identify
items on the map, and to move the map in order to view areas beyond the current viewing area
on the display.
Reference
Map Page
The map panning function is activated from the Option Menu
on the Map Page. Use
the THUMB STICK to move the panning arrow (also referred to as the map pointer) in the desired direction. If the arrow moves to the edge of the map display, the map also moves to reveal
more area and a busy hourglass appears by the cursor while the data is drawn on the screen.
Whenever you place the panning arrow on a map item, the name of that item is highlighted.
This feature applies to waypoints, roads, lakes, rivers; nearly everything that is displayed.
Press the THUMB STICK IN to mark the arrow location or display the map item information page. The Option Menu
allows you to: send the location of that item, project a
waypoint from it, save it as a waypoint, set a proximity circle around it, add it to a route, or
view the Sun & Moon phase or view Hunt & Fish information from it. On-screen buttons at
the bottom of the page allow you to Goto the map item, display it on the map or to select ‘OK’
and return to the Map Page. Press the PAGE button to stop panning the map.
Map Page with
Panning Arrow
To find an item near the map pointer:
1. When using the panning arrow, press and hold the THUMB STICK IN to display the
Shortcuts Menu.
2. Select ‘Find ‘N Go’ to display items. Select the category you wish to search (waypoints,
contacts, etc.), then select ‘Near Map Pointer’ from the pop-up list. The Rino 130 then
searches for the items nearest the location of the map pointer instead of your actual
location.
25
Reference
Map Page
Programming the Data Fields
Select ‘Show... Data Fields’ to view four optional Data Fields on the right side of the screen
that can be programmed to provide a variety of travel and navigation information. A list of the
choices is shown below. Not all data types are available on every page.
To program a data field:
1. Use the THUMB STICK to highlight the data field and then press IN to display the list of
data options.
2. Highlight the desired option and then press the THUMB STICK IN to change the data field
type.
Data Field Options
Thee data field options apply to the Map Page data fields and the Trip Computer data fields.
For definitions of these all data fields used in the Rino 130, refer to the Appendix.
Changing Data Fields.
26
Bearing
Course
Current Destination
Current Distance
Current ETA
Current ETE
Elevation
Final Destination
Final Distance
Final ETA
Final ETE
GPS Accuracy
Heading
Maximum Speed
Moving Avg. Speed
Odometer
Off Course
Overall Avg. Speed
Pointer
Speed
Sunrise
Sunset
Time of Day
To Course
Trip Odometer
Trip Time - Moving
Trip Time - Stopped
Trip Time - Total
Turn
Velocity Made Good
Vertical Speed
Trip Computer Only:
Location (lat/lon)
Location (selected)
Reference
Setting up the Map
The ‘Setup Map’ option displays the five Map Setup Pages, each accessed by an on-screen
button.
To use Map Setup options:
1. Select ‘Setup Map’ from the Option Menu
display the Map Setup Page.
Map Page
Setup Items
and then press the THUMB STICK IN to
Sub-Page
Buttons
General Setup
2. Press UP or DOWN on the THUMB STICK to highlight the desired sub-page button, which
displays the options list for that sub-page to the left.
Lines Setup
3. Press LEFT, then UP or DOWN on the THUMB STICK to highlight an item on the list. Press
RIGHT to return to the sub-page buttons.
5. Use the THUMB STICK to highlight the desired option and then press it IN to activate.
6. Press the PAGE button or the on-screen ‘X’ button to return to the Map Page.
Points Setup
Text Setup
Options
Map Data Setup
General Setup
Orientation - ‘Track Up’ or ‘North Up’; fixes the top of the map display to the current track
heading or to a north heading.
Auto Zoom - On or Off; automatically scales the map to display both your current location
and the next point to which you are navigating.
Detail - Most, More, Normal, Less, or Least; controls how much map detail you see. This
setting only applies to a map feature set to ‘Auto’. Those features which have a specified
scale or are turned ‘Off’ are unaffected by this setting.
Lock on Road - On or Off; available only if MapSource Data is loaded; when ‘On’ the
triangle icon locks to the road that you are traveling.
General Setup
27
Reference
Map Page
Display Mode - Land or Water.
Tracks Setup
Saved Tracks and Track Log - Scale options; ‘Off’, ‘Auto’, or 20 ft.–500 miles, sets the
maximum scale at which the feature should appear on the screen. Some types of data
display only at certain zoom scales.
Goto Line - Bearing or Course.
Track Points - Select the number of track points per track. UP to 10,000 active Track
Points allowed
General Setup
Lines Setup
Points Setup
Text Setup
Map Data Setup
Text Setup
Map Features Setup
Points of Interest, Waypoints, Street Label, and Land Cover - ‘Off’, ‘Auto’, or 20 feet
to 500 miles, sets the maximum scale at which that feature should appear on the screen.
Some types of data display only at certain zoom scales.
Text Setup
Points of Interest, Waypoints, Street Label, and Land Cover - ‘None’, ‘Small’, ‘Medium’, or ‘Large’; control the screen size of the name.
Map Data Setup
Show - Check box; check mark determines if map data is used or not. Option Menu allows
you to choose to show all, show none, or show specific MapSource Data. See also the
Appendix.
28
Measuring Distance
Reference
To use the Measure Distance option:
1. Select ‘Measure Distance’ from the Option Menu
and then press the THUMB STICK IN
to display the Panning Arrow. ‘Ref’ displays under the arrow.
Map Page
2. Use the THUMB STICK to move about on the Map Page until you reach the point to which
you want to measure. A new ‘Map Pointer’ field displays showing the location of the
pointer and the direction and distance from where you began the measuring.
3. To begin measuring from a different point, press the THUMB STICK IN at the desired
location.
4. To stop measuring, press the PAGE button.
Map Pointer Field
Measuring distance.
29
Reference
Navigation Page
NAVIGATION PAGE OVERVIEW
The Navigation Page provides active guidance with a rotating compass ring that shows your
course (track) while you are moving and a bearing pointer to indicate the current direction to
your destination (bearing) relative to the course.
The Data Field at the top of the page, by default shows you the name of your destination.
All five Data Fields can be programmed to display a variety of navigation data. The list of data
field choices may be found on page 26 and definitions may be found in the Appendix.
The Compass Ring functions as a magnetic compass when you are stationary. When you are
moving, the heading is controlled by the GPS receiver (based upon settings customized in the
Heading Setup Page).
Destination
(Waypoint) Name
Straight Line Distance
to the Destination
Times to Destination
Bearing Pointer
Selectable Data Fields
Compass Ring
NOTE: The Compass should be calibrated for the greatest accuracy. Refer to page 34
for information on calibrating the compass.
30
Using the Navigation Page
The two main components of the Navigation page are the Bearing Pointer and Compass
Ring. The Bearing Pointer always points directly to the destination, no matter what your current location might be. The Compass Ring displays your heading.
Reference
Navigation Page
While you are navigating a route, the pointer indicates the direction (a bent arrow) of the
turn to the next point in the route as well as the direction to the current point when you get
within 15 seconds Estimated Time of Arrival of the current point.
For example, if the arrow is pointing straight up, you are going directly to your destination. If it points any direction other than up, turn and move towards the direction the arrow
is pointing until it points up, and then continue in that direction. If you are using the ‘Course
Pointer’ option instead and you drift away from the original line of travel to your destination,
the Course Deviation Indicator (CDI) provides graphic indication of drift (right or left) and
displays the distance off course.
When you are not on an active Goto, Track, or Route (in other words: not traveling to a
recorded destination), the window at the top of the page is blank when ‘Destination’ is selected.
The Compass Ring displays your heading while you are moving, but the data fields to the right
of the page will not display any destination related data, such as Estimated Time of Arrival.
To stop navigating:
1. Highlight the on-screen Option Menu
and press the THUMB STICK.
CDI Scale
Navigation Page with
Course Pointer and
Course Deviation Indicator
(CDI) Scale active.
button at the top of the Navigation or Map Page
2. Select ‘Stop Navigation’, then press the THUMB STICK.
31
Reference
Navigation Page
NAVIGATION PAGE OPTIONS
Sight ‘N Go - Use the Sight ‘N Go feature to locate a landmark visually and then lock in a
magnetic heading to it.
Stop Navigation - Cancels navigation (“Grayed out” or disabled unless you are navigating on a
Goto, Track, or Route.)
Bearing Pointer/Course Pointer - Toggles between Bearing (always directed at destination)
and Course (distinctive with dots across center of compass, shows amount of correction needed
to be back on course.)
Show Data Fields/Big Compass - Toggles to display data fields on the right side of the display or removing the data fields and showing a larger compass.
Navigation Page Option
Menu
Calibrate Compass - Calibrates the electronic compass. Follow the on-screen instructions.
Restore Defaults - Returns options and data field choices to factory designations.
To change data fields:
1. Use the THUMB STICK to highlight the desired data field and then press it IN to display the
list of data options.
2. Select the desired option from the list and press the THUMB STICK IN. The list of data field
choices may be found on page 26 and definitions may be found in the Appendix.
Navigation Page with
Bearing Pointer and
Big Compass..
32
Using Sight ‘N Go
Reference
To use Sight ‘N Go to navigate:
1. Use the PAGE button to access the Navigation Page and then use the THUMB STICK to
access the Option Menu
.
Navigation Page
2. Use the THUMB STICK to highlight ‘Sight ‘N Go’ and press IN. Note that the compass ring
with pointer is in-line with the two sighting marks on the case.
3. Hold the Rino 130 at eye level and line up the two sighting marks on the case with the
distant object. Press the THUMB STICK to ‘Lock Direction’.
4. To navigate to your destination, select ‘Set Course’ and press the THUMB STICK. Begin
traveling to your destination using the pointer as a guide.
To view your destination as a waypoint, select ‘Project Waypoint’ and press the THUMB
STICK. To re-sight the destination, press the THUMB STICK IN when ‘Re-Sight’ is
highlighted.
Sight ‘N Go Page
Sighting Marks
Rino 130 held level
for Sight ‘N Go
33
Reference
Navigation Page
Calibrating the Compass
The Electronic Compass must be calibrated outdoors when you first use the Rino 130 and
after new batteries have been installed. The accuracy of the Electronic Compass is adversely
affected if the unit is not held level or is held near items that generate magnetic fields, such as
cars, large belt buckles, etc.
To Calibrate the Electronic Compass:
1. Use the PAGE button to access the Navigation Page.
2. Use the THUMB STICK to highlight the Option Menu on-screen button
and press IN.
3. Highlight the ‘Calibrate Compass’ option and press the THUMB STICK IN.
4. Press the THUMB STICK to activate the ‘Start’ button and then follow on-screen directions
for holding and turning the unit. Hold the unit level when calibrating the compass.
The unit displays a “Just Right”, “Too Fast” or “Too Slow” message for you to adjust your
turning speed as needed. The “Calibration Successful” message displays when finished. If
a “Calibration Failed” message displays, repeat the process.
Compass Calibration
Page
When you manually turn the Compass Off, it stays off until you manually turn it On again.
Sometimes, however, when you turn the Compass On, the Rino 130 overrides the Compass and
uses the GPS receiver to track your heading. The criteria for switching between the Compass
and the GPS is customized on the Heading Setup Page (see section Heading Setup Page).
Turning the Compass On and Off
Calibrating the compass: Hold the unit level and face
up. Turn the unit around as shown above.
34
•
Press and hold the ZOOM (Z) button. A message appears on the screen indicating that the
compass has been turned on or off. OR
•
Press the PAGE button to access the Main Menu. Select ‘Setup’ and then ‘System’. Turn
the compass on and off through the System Setup Page (see section System Setup Page).
ALTIMETER PAGE OVERVIEW
The Altimeter Page provides the current elevation, rate of ascent/descent, a profile of elevation changes over distance or time, or a profile of pressure changes over time. The Altimeter
Page’s Option Menu
allows you to select from a variety of display options such as plotting
over time, plotting over distance, displaying the zoom ranges of measurement, viewing elevation or pressure points, and resetting data displays. Two user selectable data fields allow you to
display a variety of current and recorded pressure and elevation related data.
Reference
Altimeter Page
NOTE: The Altimeter should be calibrated for the greatest accuracy. Refer to page 39
for information on calibrating the Altimeter.
Status Window
Status Window is located at the top of the page and displays the current elevation and your
current rate of ascent or descent when moving. It can also display the ambient pressure.
Profile Field
Profile Field is located in the center of the page and can be configured to display either
elevation or ambient pressure plots as selected from the Altimeter Page Option Menu
.
Data Fields at the bottom of the page are user selectable and display a variety of recorded or
current data.
Data Fields
35
Reference
Altimeter Page
ALTIMETER PAGE OPTIONS
The Altimeter Page Option Menu
allows you to select the type of information and how
it is to be displayed. Altimeter Page Options include:
Plot Over Time/Distance - Plots the changes in elevation or pressure over a length of time
or over a distance. When ‘Plot Over Distance’ is selected, ‘Plot over Time’ is displayed in the
Option Menu (and vice versa).
View Pressure/Elevation Plot - Displays a record of changes in barometric pressure or elevation for a set period of time.
Zoom Ranges - Sets the zoom range for elevation, distance, or time.
View Points - Shows the elevation, time of day, and date a specific point was created
Reset… - Clears recorded data from the page to begin recording new data.
Calibrate Altimeter - Increases the accuracy of the altimeter. You must know your elevation
or pressure to calibrate the altimeter.
Altimeter Page Option
Menu
36
Restore Defaults - Returns the Altimeter Page to the original factory settings (defaults).
Viewing Pressure/Elevation Plots
When selecting the ‘View Elevation Plot’ option you can plot a profile of elevation changes
that occur as you navigate over a set distance or period of time. When you select ‘View Pressure
Plot’ you can view a record of changes in barometric pressure for a set period of time. When
one option is active the other displays on the Altimeter Page Option Menu
.
Reference
Altimeter Page
To view elevation or pressure plots:
1. Use the THUMB STICK to highlight the desired option from the Option Menu and then
press IN to display the plot.
2. Adjust time and distance measurement as desired using the Elevation Plot Zoom Ranges
feature explained below.
3. To clear the plot and start a new one, you must clear the ‘Track Log’.
Adjusting the Zoom Ranges
You can set the Zoom Ranges for elevation, distance, or time when you display the ‘View
Elevation Plot’. You may change the ranges for the vertical distance and the time. Ranges for
‘View Pressure Plot’ are fixed at 6.8 millibars and 12 hours.
Altimeter Page
To adjust zoom ranges:
1. Select the type of plot you want to display and use the THUMB STICK to highlight ‘Zoom
Ranges’ from the Option Menu.
2. Press the THUMB STICK IN to display the Zoom Ranges Page.
3. Move the THUMB STICK UP or DOWN to adjust the vertical distance and LEFT or RIGHT to
adjust either the time or distance. Press IN to return to the Plot Page.
Zoom Range selection
37
Reference
Altimeter Page
Viewing Points
The ‘View Points’ option allows you to scroll through the stored elevation profile and to
view a single point along the profile. When the pointer is stopped at a location along the profile, the display shows the elevation, time of day and date the point was created.
To use the ‘View Points’ option:
1. Use the THUMB STICK to access the Option Menu.
2. Highlight the ‘View Points’ option and press the THUMB STICK IN to display the View
Points Page.
3. Move the THUMB STICK RIGHT or LEFT to scroll the profile past the pointer in the center of
the page.
As the profile moves past the pointer, the status window at the top of page changes to
display the date, time, and altitude for the point beneath the pointer.
Resetting Data
You can reset the elevation data and the maximum elevation data by selecting the ‘Reset’
option from the Altimeter Page Option Menu
.
View Points Option Page
To reset the elevation data and max elevation fields:
1. Use the THUMB STICK to highlight the ‘Reset’ option from the page Option Menu and
press the THUMB STICK IN to display the ‘Reset’ page.
2. Use the THUMB STICK to highlight the reset options on the page and then press the
THUMB STICK IN to place a check mark in the box next to a selected item.
3. Move to the ‘Apply’ button and press the THUMB STICK IN to reset the data fields.
38
Calibrating the Altimeter
Because the Rino 130 relies on the Barometric pressure to determine the elevation and the
pressure at any given elevation can fluctuate, you can calibrate the altimeter to increase its accuracy. You must know the elevation or pressure at your current location, information you can
obtain from a map or other reliable source.
Reference
Altimeter Page
To manually calibrate the altimeter:
1. Use the THUMB STICK to access the Option Menu.
2. Highlight the ‘Calibrate Altimeter’ option and press the THUMB STICK to display the
Calibration Page.
Altimeter Data Field Options:
3. At the message asking “Do You Know The Correct Elevation?” highlight the on-screen ‘Yes’
button and press the THUMB STICK IN to enter your elevation. When finished, highlight
‘OK’ and press it IN to return to the Altimeter Page.
Ambient Pressure
For definitions refer to the Appendix.
Average Ascent
Or At the message asking “Do You Know The Correct Pressure?” highlight the on-screen ‘Yes’
button and press the THUMB STICK IN to enter your elevation. When finished, highlight
‘OK’ and press it IN to return to the Altimeter Page.
Average Descent
Programming Data Fields
The two user-selectable data fields support this page and can be programmed to display the
data options listed to the right.
Maximum Ascent
To program a data field:
Barometer
Elevation
Maximum Descent
Maximum Elevation
Minimum Elevation
1. Use the THUMB STICK to highlight the desired data field and then press it IN to open the
data field option pop-up window.
Total Ascent
2. Use the THUMB STICK to move UP or DOWN the menu to highlight a desired data option
and then press IN to place it in the data field.
Vertical Speed
Total Descent
39
Reference
Trip Computer Page
TRIP COMPUTER PAGE OVERVIEW
The Trip Computer Page by default displays up to seven different
types of navigation data. Choosing ‘Big Numbers’ will display 2 large
data fields.
Each data field is selectable and can contain one of many data
information options. The default settings for these fields are shown
in the illustration. The list of data field choices may be found on
page 26 and definitions may be found in the Appendix. When the
data field title is selected, press the THUMB STICK IN to select a
new data field choice.
Trip Computer Page,
Small Numbers
Selecting a data field
By selecting the information options that you prefer and arranging them in a desired order
on the page, you can customize the Trip Computer Page to meet your navigation needs.
TRIP COMPUTER PAGE OPTIONS
The Option Menu allows you to reset the Trip Computer data when you are ready to start a
new trip, choose between Big or Small Numbers, and Restore Defaults.
Reset - Clears recorded data from the page to begin recording new data.
Big/Small Numbers - Changes the display from seven small data fields to two large data fields.
Restore Defaults - Returns the Trip Computer Page to the original factory settings (defaults).
Trip Computer Page,
Big Numbers
40
MAIN MENU OVERVIEW
The Main Menu provides access to additional Rino 130 feature pages. The pages listed
below provide enhancements to Rino 130 operation. Press the PAGE button repeatedly to cycle
to the Main Menu or select it from the Main Page Menu at the top of each main page.
Reference
Main Menu Page
Using the Main Menu
The Main Menu allows access to many features and pages in the Rino 130. Please refer to
the Features section for a complete description of the items accessed through the Main Menu.
Mark Waypoint Page - Allows you to mark and store a waypoint for your current location or
a map pointer location.
Find ‘N Go Menu - Allows you to locate and Goto; Waypoints, Favorite Locations, Cities, Interstate Exits, Points of Interest, Addresses, and Intersections. (Some require MapSource data.)
Routes Page - Allows you to create and store routes for repeated use.
Tracks Page - Provides access to the track log, saved tracks, and contact tracks.
Main Menu Page
Proximity Page - Allows you to set a proximity alert distance around contacts or waypoints.
Satellite Page - Provides a picture of the satellite signal tracking and tells you when the unit is
ready to navigate.
41
Reference
Main Menu Page
Setup Page - Allows tailoring of items such as time format, units of measure, display backlighting timeout and contrast adjustment, heading selection, interface setups, and system software
information.
Calendar Page - Provides you with a monthly calendar with programmable reference notes.
Alarm Clock - Provides a settable 24-hour alarm clock.
Calculator - Provides a calculator feature available in two forms: Standard or Scientific.
Stopwatch Page - Allows you to use the unit as a stopwatch, including a lap timer.
Sun & Moon Page - Shows a graphic display of both the Sun & Moon locations at various
times, dates, and locations.
Hunt & Fish Page - Provides you with a listing of best times for hunting and fishing for a
chosen location.
Area Calculation Page - Use this function to calculate area as you move around.
Games Page - Games are provided as an entertainment feature.
Many of the items in the Main Menu Page are discussed in-depth in the Features section. Refer
to the specific section for more information.
42
Reference
MAIN MENU OPTIONS
Through the Main Menu you can establish the sequence of pages.
Page Sequence Setup
You may add, remove, or reorder any of the Main Pages, plus additional pages. The default
Main pages are Radio, Map, Navigation, Altimeter, Trip Computer, and Main Menu. The
Main Menu cannot be removed from the page sequence. If a page is added to the Main Page
Sequence, it does not appear in the Main Menu.
Main Menu Page
To move, insert or remove a Main Page:
1. From the Main Menu, highlight the Option Menu on-screen button
THUMB STICK IN. Highlight ‘Page Sequence Setup’ and press IN.
and press the
2. To move a page in the page sequence, highlight the page and press IN. Select ‘Move’ then
move the Menu item UP or DOWN using the THUMB STICK. When the desired position is
displayed and press the THUMB STICK IN.
Main Page Sequence
Setup Page
3. To insert a new page, highlight the page you wish to insert it before and press IN. Select
‘Insert’, then choose a page from the list and press the THUMB STICK IN.
To remove a page in the order, highlight the page and press IN. Select ‘Remove’ and press
the THUMB STICK IN.
Inserting a new page in the
Page Sequence
43
Features
Shortcuts Menu
SHORTCUTS MENU OVERVIEW
The Shortcuts Menu is accessed by pressing the THUMB STICK IN until the menu pops up
on the middle of the display. The Shortcuts Menu can be accessed from most pages.
Mark Waypoint - Marks your current location as a waypoint. Opens the Mark Waypoint page
that allows you to customize the waypoint information as well as Goto or show on the Map.
Find ‘N Go - Opens the Find ‘N Go Page. From the Find ‘N Go page, you can find waypoints,
contacts, cities, and exits. You may also find Points of Interest, addresses, and intersections if a
MapSource product is loaded into the Rino 130.
Weather Radio - Toggles between the Weather Radio and the FRS/GMRS Radio.
Send Note - Sends a note to other Rino 130 users.
Shortcuts
Menu
44
Enable Keylock - Enables keylock so buttons are not inadvertently pushed. Press and hold
the PAGE button to unlock the buttons.
Features
WAYPOINTS
There are numerous ways to create, edit, and use waypoints. Using the Mark Waypoint
Page and the Find ‘N Go Menu are two common pages for creating and editing waypoint. You
can also create a waypoint using the Map Page. The Rino 130 holds up to 500 waypoints.
Waypoints
Mark Waypoint Page
The Mark Waypoint Page allows you to mark and record your current location as a
waypoint and appears with a graphic name block (man with a flag) that displays the assigned
number for that waypoint and a waypoint symbol.
To mark your current location and open the Mark Waypoint Page:
Mark Waypoint Page icon
1. Press and hold the THUMB STICK IN until the Shortcuts Menu opens.
2. Highlight ‘Mark Waypoint’ and press the THUMB STICK IN. The Mark Waypoint Page
opens. You can also access this page by highlighting the Mark Icon on the Main Menu
Page and pressing the THUMB STICK IN.
3. To save the waypoint, highlight ‘OK’ and press the THUMB STICK IN. If you do not want to
save it as a new waypoint, press the PAGE button to cancel.
Symbol
Waypoint
Name
Waypoint
Details
To change Mark Waypoint Page Options:
•
To change the name of the waypoint, use the THUMB STICK to highlight the waypoint
name field.
•
To assign an identifying symbol to a waypoint, use the THUMB STICK to highlight the
symbol block just above the waypoint name.
•
Mark Waypoint Page
To view the waypoint details, highlight the details field and press LEFT or RIGHT on the
THUMB STICK to change to the next data field.
45
Features
Creating Waypoints
To create a waypoint for a map feature:
Waypoints
1. With the Pan Map feature active, move the panning arrow (map pointer) to the map item
you want and highlight it.
2. Press IN and release the THUMB STICK to display the item information page.
3. With the Information Page displayed, highlight the Option Menu button
the page and then press the THUMB STICK to open the menu.
at the top of
4. Highlight ‘Save As Waypoint’ and press the THUMB STICK to save the item as a waypoint.
To create a waypoint using the panning arrow:
1. With the Pan Map feature active, move the panning arrow (map pointer) on the map to the
location you want to mark, then press the THUMB STICK.
Saving a map feature as
a waypoint
2. The Mark Waypoint Page displays, automatically assigning a number to the waypoint.
To create a waypoint by manually entering its coordinates (lat/lon):
1. Press IN and hold the THUMB STICK to access the Shortcuts Menu. Highlight ‘Mark
Waypoint’ and press IN. You can also use the Find ‘N Go to view a previous waypoint.
2. Highlight the details field and press LEFT or RIGHT on the THUMB STICK to change to
the Location field. Press IN and enter the new coordinates using the on-screen numerical
keyboard. Highlight and press ‘OK’ when finished.
3. You may also change the waypoint name and/or symbol or add notes.
Creating a waypoint by entering
the coordinates
46
Projecting a Waypoint
Projecting a waypoint from any map item (another waypoint, etc.) allows you to establish a
new waypoint on a bearing and distance projected from that map item.
Features
Waypoints
To project a waypoint:
1. Select a map item from the Find ‘N Go Menu.
2. Highlight the Option Menu on-screen button
at the top of the Information Page and
press the THUMB STICK IN to display the options. Highlight ‘Project Waypoint’ and press
IN.
3. Highlight either the bearing or distance field, then press the THUMB STICK IN to display
the numerical keyboard. Enter the new bearing or distance, then highlight ‘OK’ and press
IN to finish.
Editing a Waypoint
A waypoint or contact can be edited to add notes or change the map symbol, name, coordinates, or elevation. It can also be deleted.
Project Waypoint Page
To edit a waypoint:
1. Use the Find ‘N Go Menu to display the waypoint/contact or highlight it on the Map Page
and press the THUMB STICK IN.
2. To make changes to the waypoint map symbol, name, location coordinates, elevation
fields and notes, highlight the desired field and press the THUMB STICK IN to display
the keyboard. (For Notes, highlight ‘Edit’ and press IN to start entering data, up to 30
characters.) Select ‘OK’ and press the THUMB STICK IN to finish.
3. Highlight the ‘OK’ button the press the THUMB STICK to save the changes.
Editing a waypoint note
47
Features
To delete a waypoint or contact:
1. Use the Find ‘N Go feature to display the point.
Waypoints
2. Highlight the ‘Delete’ button and then press the THUMB STICK IN. Confirm the deletion.
To move a waypoint by dragging it:
1. Use the Find ‘N Go Menu to display the Waypoint Page for the waypoint you want to move.
2. Highlight and press the ‘Map’ on-screen button to display the waypoint on the map.
3. With the waypoint highlighted by the panning arrow, press IN and release the THUMB
STICK. The word “Move” displays beneath the panning arrow.
4. Use the panning arrow to drag the waypoint to the new location and then press the
THUMB STICK IN to place it.
Deleting a waypoint
Press the PAGE button before pressing the THUMB STICK to cancel moving of the
waypoint and return to the Main Pages.
To save Map or Find ‘N Go items as waypoints:
1. Access the Information Page for the desired item (highlighted from the map or selected
from the Find ‘N Go Menu).
2. Open the Option Menu at the top of the page, select ‘Save As Waypoint’.
3. Press the THUMB STICK IN to save the item to the Waypoints List.
4. Highlight ‘Save As Waypoint’ and press the THUMB STICK IN.
Saving an item as a waypoint
48
FIND ‘N GO MENU
The Find ‘N Go Menu allows you to find stored locations (waypoints) and map items (cities,
exits, etc.). They can be found by name or by those nearest to your current location. If you
are using certain MapSource data, the list of find locations is expanded to include categories for
Points of Interest, Street Addresses, and Intersections. If you would like to use an option that is
grayed out (disabled), you need to load map detail using MapSource.
Features
Find ‘N Go
To access the Find ‘N Go Menu:
1. Press and hold the THUMB STICK IN to access the Shortcuts Menu.
2. Highlight ‘Find ‘N Go’ press IN.
Or
Find ‘N Go icon
1. Press the PAGE button or the on-screen Main Page Menu button to display the Main Menu.
2. Highlight the ‘Find ‘N Go’ icon and press the THUMB STICK IN.
For some categories, there are two methods of listing. The ‘By Name’ list contains every
item in the map database for the selected category, while the ‘Nearest’ list contains only those
items that are near to your Current Location or the Map Pointer.
These pages are structured with a set of sub-menus and location information pages that
guide you through the process of finding locations.
Find ‘N Go Menu
49
Features
Find ‘N Go
Finding a Waypoint
Waypoints that you have created and stored in the Rino 130 can be found by selecting
the “Waypoint’ option from the Find ‘N Go Menu. You can find a waypoint from the list of
waypoints using the ‘By Name’ or ‘Nearest’ options as explained on the previous page. When
selected from the list, the waypoint displays on the Waypoint Information Page.
The Waypoint Information Page displays the waypoint name or number, a map symbol, the
location in lat/lon, elevation, distance, bearing, and three on-screen buttons for ‘Goto’, ‘Map’,
and ‘OK’ functions.
To find a waypoint by nearest:
1. Use the THUMB STICK to select ‘Waypoint’ from the Find ‘N Go Menu. Press the THUMB
STICK IN to select ‘Nearest’ from the pop-up menu. Press the THUMB STICK IN to display
the Waypoints List.
2. Use the THUMB STICK to select the desired waypoint from the list and then press the
THUMB STICK IN to display the Information Page for that waypoint.
Nearest Waypoints selected in
Find N’ Go Menu
50
3. With the Information Page displayed, select ‘Goto’ to create a direct line of travel to the
waypoint. Select ‘Map’ to view the waypoint location on the map or select ‘Delete’ to
delete the waypoint.
to access additional features. You can select: Send
4. Press the Option Menu button
Location (to other Rino users), Project Waypoint, Set Proximity (alarm), Add to Route, View
Sun & Moon (reports for that waypoint), View Hunt & Fish (reports for that waypoint), or
Reposition Here.
To find a waypoint by name:
1. Use the THUMB STICK to select ‘Waypoint’ from the Find ‘N Go Menu. Press the THUMB
STICK IN to select ‘By Name’ from the pop-up menu. Press the THUMB STICK IN to
display the Waypoints List.
Features
Find ‘N Go
2. Use the THUMB STICK to enter the name of the waypoint that you would like to find.
3. Select ‘OK’ when you are finished entering the name. The waypoint list opens with the
name closest to the name you entered on the top.
4. Select the desired waypoint from the list and then press the THUMB STICK IN to display
the Information Page for that waypoint.
5. With the Information Page displayed, select ‘Goto’ to create a direct line of travel to the
waypoint. Select ‘Map’ to view the waypoint location on the map or select ‘Delete’ to
delete the waypoint.
to access additional features. You can select: Send
6. Press the Option Menu button
Location (to other Rino users), Project Waypoint, Set Proximity (alarm), Add to Route, View
Sun & Moon (reports for that waypoint), View Hunt & Fish (reports for that waypoint), or
Reposition Here.
Find ‘N Go Menu
Entering a waypoint name to
find By Name
51
Features
Find ‘N Go
Finding a Contact
Contacts that you have received in the Rino 130 can be found by selecting the ‘Contacts’
option from the Find ‘N Go Menu.
To find a contact:
1. From the Find ‘N Go Menu, highlight ‘Contacts’ and press the THUMB STICK IN.
2. From the Contacts List, select the desired contact and press the THUMB STICK IN.
3. With the Contact Information Page displayed, select ‘Goto’ to create a direct line of travel
to the contact. Select ‘Map’ to view the contact’s location on the map or select ‘Delete’ to
delete the contact.
If the contact did not have a GPS location on the last transmission, a question (?) mark
appears below the flag. To view the contact details, highlight the details field and press
LEFT or RIGHT on the THUMB STICK to change to the next data field.
Contact List
Contact Information Page
4. Press the Option Menu button
to access additional features. You can select: Poll
location, Send Location (to other Rino users), View Track, Project Waypoint, Save as a
waypoint, or Set Proximity (alarm).
52
Finding a City
Cities can be found by selecting the ‘Cities’ option of the Find ‘N Go Menu, selecting the
city from the list of ‘Nearest’ or ‘By Name’, and then displaying the City Information Page.
The City Information for the selected city displays, including the city name, the size by
population, and distance from your location. You can view it on the map, or create a Goto
direct route to the city from your current location or from a location defined by the Panning
Arrow (Map Pointer). You can also save the city as a waypoint or add it to an existing route.
Features
Find ‘N Go
To find a city:
1. Use the THUMB STICK to select the ‘Cities’ option, then press it IN to display the find
‘Nearest’ or find ‘By Name’ prompt. Selecting ‘By Name’ displays the keyboard as an
alternative scrolling through the list of nearest cities. If you are currently panning the map,
the option ‘Near Map Pointer’ appears in place of the ‘Nearest’ option.
Find ‘N Go Menu
2. If using find ‘By Name’, begin spelling the name of the city by using the keyboard. When
you have entered enough characters to define the name, a match list displays. If you are
using find ‘By Nearest’ or ‘Near Map Pointer’ scroll through the list to find the city you
want. Use the THUMB STICK to select the desired city from the list and then press it IN to
display the Information Page for that city.
3. With the Information Page displayed, you can select ‘Goto’, ‘Map’, or ‘OK’ options.
to access additional features. You can select: Send
4. Press the Option Menu button
Location (to other Rino users), Project Waypoint, Save as a Waypoint, Set Proximity (alarm),
Add to Route, View Sun & Moon (reports for that waypoint), or View Hunt & Fish (reports
for that waypoint).
Find Nearest Cities List
53
Features
Find ‘N Go
Finding an Exit
You can use the Find Exit option to locate a nearby exit on an interstate highway. Exits are
listed only by ‘Nearest’. Exit information pages provide a variety of information about services
near each exit, such as rest stops, lodging, restaurants, and service stations. Some services such
as service stations on this page can be selected and a separate information page displays with
specific information concerning what types of fuel, mechanical, and food services are available.
To find an exit:
1. Use the THUMB STICK to highlight ‘Exits’ and then press it IN to display the Exit List.
2. Highlight and select an exit type by pressing the THUMB STICK IN.
3. A list of exits nearest to you displays. The title box indicates the interstate highway that is
served by the exits. Two fields at the bottom of the page indicate distance and bearing to
the exit. Scroll through the list to highlight the desired exit.
4. Press the THUMB STICK IN to display the Information Page for that exit. This page
contains the exit description with a list of available services near that exit along with the
distance and bearing fields.
5. Use the THUMB STICK to move to the list of services and highlight a selection from the list.
Exit Information Page
6. Press the THUMB STICK IN to display the Information Page for the selected service.
The Exit Services Information Page displays the name of the service, its direction from the
exit, and a list of the services available, each marked by a check.
At the bottom of these Information Pages are on-screen buttons for ‘Goto’, ‘Map’, and ‘OK’.
7. Press the Option Menu button
to access additional features. You can select: Send
Location (to other Rino users), Project Waypoint, Save as a Waypoint, Set Proximity (alarm),
Add to Route, View Sun & Moon (reports for that waypoint), or View Hunt & Fish (reports
for that waypoint).
54
Finding a Point of Interest
You can use the Find Points of Interest option to locate a nearby restaurant, lodging,
landmark, public building, park, etc. However, you must have transferred a MapSource
MetroGuide map to the unit map database. Otherwise, this option, plus Address and Intersection options, are grayed out and are not functional. Here is a list of Point of Interest categories:
• Food & Drink
• Lodging
• Attractions
• Entertainment
• Shopping
• Services
• Transportation
• Emergency & Govt.
• Manmade Places
IN many instances, these categories are subdivided into types, such as in the instance of
Food & Drink. When you select Food & Drink from the list of categories, you are then presented with a list of types that includes ‘All Types’ and cuisine options such as American, Asian,
Barbecue, Chinese, and many more.
Once you have selected an item, you can display the Information Page for that item. You
can then use the on-screen buttons to ‘Goto’ or view the location on the ‘Map’; or use the Option Menu
for more choices.
Features
Find ‘N Go
Points of Interest
Food & Drink types
55
Features
Find ‘N Go
To find a point of interest:
1. Use the THUMB STICK to highlight ‘Points of Interest’ and then press it IN to display the
Points of Interest Categories List.
2. Use the THUMB STICK to select the desired category and then press it IN to display the
Types List.
3. Use the THUMB STICK to select the desired type and then press it IN to display the list for
that type.
4. Use the Option Menu
at the top of page to select from either ‘By Name’ or ‘Nearest’
options. Selecting ‘By Name’ displays a keyboard allowing you to enter the characters of
the name you want. A list of matches displays when enough characters are entered.
5. Use the THUMB STICK to highlight your selection from the list and then press it IN to
display the Information Page for that item.
Points of Interest
6. Use the on-screen buttons to ‘Goto’ or view on the ‘Map’, or use the page Option Menu.
to access additional features. You can select: Send
7. Press the Option Menu button
Location (to other Rino users), Project Waypoint, Save as a Waypoint, Set Proximity (alarm),
Add to Route, View Sun & Moon (reports for that waypoint), or View Hunt & Fish (reports
for that waypoint).
Nearest Food & Drink
56
Finding an Address or Intersection
You can enter a street number, choose a street name from a list and find an address within
the area of map data coverage or enter two street names and locate the intersection. To use
these options, however, you must be using a MapSource product that provides this type of map
data.
Features
Find ‘N Go
To locate an address:
1. Use the THUMB STICK to highlight ‘Address’ and press it IN to display the ‘Find Address’
page.
2. Highlight the’ Number’ field and use the keyboard for entering numbers.
3. Move to the ‘Street’ field using the THUMB STICK.
4. Press the THUMB STICK IN to display the ‘Select Street Name’ list. Find the street by using
the keyboard to enter characters until a list appears.
5. With the desired street highlighted, press the THUMB STICK IN to place the street name on
the Find Address page. Repeat this process for city and postal codes, if desired. A window
at the bottom of the page displays a list of matches and the quality of each match. You
may also use the Option Menu to ‘Clear City’, ‘Clear Postal Code’ or ‘Clear All’.
6. Use the on-screen buttons at the bottom of the page to ‘Goto’, view the item on the ‘Map’,
’OK’ to close, or use the Option Menu for other choices.
Entering an Address
57
Features
Find ‘N Go
To locate an intersection:
1. Display the Find ‘N Go Menu and use the THUMB STICK to highlight the ‘Intersection’
category and press it IN to display the ‘Find Intersection’ page.
2. Highlight the first ’Street’ field and then press the THUMB STICK IN to display the ‘Street‘
list.
3. Enter the name of the street in the name field at the top of the list using the keyboard
data entry method discussed in the Quick Start Guide. Once you have spelled enough of
the street name, a list of matches displays, often with several streets on the list. Press the
THUMB STICK IN to move the highlight to the street list and then scroll up or down until
you find the street name you want. Press it IN to place the name in the field.
4. Highlight the best match and then press the THUMB STICK IN to display the Information
Page for the intersection. Use the on-screen buttons at the bottom of the page to ‘Goto’,
view the item on the ‘Map’, ‘OK’ to close, or use the Option Menu for other choices.
Finding an Intersection
58
Finding a Last Found Place
You can use the Recently Found Places option to locate Points of Interest, Cities, Waypoints
or Contacts and Intersections and other locations you have recently retrieved. The process for
finding recent points from the Find ‘N Go list is the same as finding a regular waypoint.
Features
Find ‘N Go
To find a ‘Last Found Place’:
1. Use the THUMB STICK to select the ‘Last Found Places’ option from the Find ‘N Go List and
then press it IN.
2. Press UP or DOWN on the THUMB STICK to highlight the desired sub-page button, which
will display the options list for that sub-page (Points of Interest, Cities, Waypoints/Contacts
or Intersections) to the left.
3. Press LEFT then UP or DOWN on the THUMB STICK to highlight an item on the list and
press the THUMB STICK IN to display the Information Page for that item. Press RIGHT to
return to the sub-page buttons.
Sub-page
buttons
4. With the Information Page displayed, you can select ‘Goto’ to create a direct line of travel
to the item. Select ‘Map’ to view the waypoint location or select ‘OK’. For Waypoints and
Contacts, you may also choose to ‘Delete’ to permanently remove that item.
5. Use the page Option Menu to send the location of that point, project a new waypoint from
its location, set a proximity circle, add the item to an existing route, or view sun/moon or
hunt/fish position data for this time and date.
Last Found Places Page
59
Features
Weather Radio
USING THE WEATHER RADIO
The Weather Radio can be turned on and off through the Shortcuts Menu or the Option
Menu in the Radio Page. You may also enable Weather Alerts from the Radio Page. Refer to the
Radio Page section for complete information about the Weather Radio and Weather Alert.
To turn the Weather Radio on and off:
1. Open the Radio Page by pressing the PAGE button or using the on-screen Main Page Menu
button
.
2. Use the THUMB STICK to highlight the Option Menu on-screen button
the THUMB STICK IN to display the menu.
Shortcuts Menu
and then press
3. When ‘Use Weather Radio’ is highlighted, press the THUMB STICK IN to turn on the
Weather Radio. You can select ‘Enable Weather Radio’ after the Weather Radio is on.
4. To turn the Weather Radio off, press the THUMB STICK IN when ‘Use FRS/GMRS Radio’ is
highlighted. This will switch the Rino 130 back over to the FRS/GMRS radio.
NOTE: You can also turn on and off the Weather Radio through the Shortcuts Menu.
Press and hold the THUMB STICK IN to open the Shortcuts Menu.
Radio Page with
Weather Radio on
60
When the Weather Radio is on, ‘Enable Weather Alert’ is added at the bottom of the option
menu. Press the THUMB STICK IN when ‘Enable Weather Alert’ is highlighted to turn the
feature on. You can then turn the Weather Radio off and continue normal FRS/GMRS radio
operations. When a Weather Alert is detected, the Rino 130 will break into any FRS/GMRS
transmission to automatically turn on the Weather Radio and broadcast that alert. Select ‘Disable Weather Alert’ to turn off that feature.
SENDING A NOTE
You may send a note to other Rino 130 users. When you send a note, it appears along the
bottom of the display on every Rino 130 user who is using the same Channel and Squelch Code
that you are using. The Send Note feature is great when you are trying to get the group to meet
at a certain location or tell everyone in the group something in a silent manner.
Features
Send Note
To send a saved note:
1. Press the THUMB STICK IN until the Shortcuts Menu appears.
2. Select ‘Send Note’ and press the THUMB STICK IN to open the Send Note Page.
3. Select a note from the Saved Notes list and press the THUMB STICK IN.
4. The selected note appears in the Edit Note field. Press the THUMB STICK IN to edit the
Saved Note. Refer to the Quick Start Guide for information on entering data using the
on-screen keyboard. When you are done editing the note, push the THUMB STICK IN when
‘OK’ is highlighted on the keyboard.
Send Note Page
5. Select ‘Send’ to send the note to all users. Select ‘Save’ to save the note. Select ‘Clear’ to
delete the note.
To send a new note:
1. Press the THUMB STICK IN until the Shortcuts Menu appears in the middle of the screen.
2. Select ‘Send Note’ and press the THUMB STICK IN to open the Send Note Page.
3. The Edit Note field is highlighted when the page opens. Press the THUMB STICK IN to
create a note. When you are done editing the note, push the THUMB STICK IN when ‘OK’
is highlighted on the keyboard.
Editing a note
4. Select ‘Send’ to send the note to all users. Select ‘Save’ to save the note. Select ‘Clear’ to
delete the note.
61
Features
Goto
USING A GOTO
The Goto function allows you to create a direct route to a destination, (waypoint, city, or
point of interest). Once you have accessed the Information Page for an item, use the ‘Goto’
button at the bottom of the page to initiate travel, using the Map and Navigation Pages for
guidance.
To activate a Goto:
1. Use the Find ‘N Go Menu to access the Information Page for any desired destination and
use the THUMB STICK to highlight the Goto button.
2. Press the THUMB STICK IN to start navigation.
Activating a Goto
3. Observe the Navigation Page, it displays the name of your destination, the distance from
your current location, and a Bearing Pointer indicating the direction you should travel. The
time required to reach your destination displays when you begin to travel and establish a
predicted rate of movement. The Data Fields to the right of the page display information
relative to your travel.
4. Use the PAGE button or Main Page Menu to access the Map Page and observe your
movements and a dark line indicating the direct path from your current location to your
destination.
5. Use the Bearing Pointer on the Navigation Page to maintain travel in the right direction and
observe distance and time information to monitor your progress.
Viewing a Goto on the
Map Page
62
6. When you are close to your destination, an “Arriving at Destination” message appears. If
you move past the destination the Bearing Pointer reverses and the distance increases.
To stop navigation, select the on-screen Option Menu button
at the top of the
Navigation or Map Page. Select ‘Stop Navigation’, then press the THUMB STICK IN.
ROUTES OVERVIEW
Route navigation allows you to create a sequence of intermediate waypoints that leads you
to your final destination. The Rino 130 stores 20 routes, each with up to 50 waypoints. A
route can be created and modified from the Route Page, and waypoints can be added to a route
from the Find ‘N Go Menu. More complex routes can be created using a PC and MapSource
mapping programs and then transferred to the unit’s memory.
Features
Routes Page
Creating and Using a Route
To create a route:
1. Access the ‘Routes’ page from the Main Menu. The page has a ‘New’ button, a list of
routes, and the number of unused routes.
2. Use the THUMB STICK to highlight the ‘New’ button and press it IN to display the route
Setup Page.
Routes Page icon
3. With an empty row (dashed) in the route list highlighted, press the THUMB STICK IN to
display the Find ‘N Go Menu.
4. Select a route waypoint from one of the Find ‘N Go Menu categories and display the
Information Page for the selected waypoint, city, exit, point of interest, etc. Highlight the
on-screen ‘Use’ button and press the THUMB STICK IN to place it on the Routes List.
5. To add more waypoints to the route, repeat the process in Steps 3 and 4. The route is
named for the first and last waypoints on the route.
You can add waypoints to the end of an existing route at any time by using the Find ‘N Go
Menu.
Routes List Page
63
Features
Routes Page
To add a Find ‘N Go Menu item to a route:
1. Select an item from the Find ‘N Go Menu and display its Information Page. If a contact is
used in a route, the route changes as the contact’s position is updated, or it may be saved
as a Waypoint to serve as a stationary point.
2. Select the page Option Menu and select ‘Add To Route’ to display the Routes List.
3. Highlight and select the route desired and then press the THUMB STICK IN. A “Waypoint
Added Successfully” message displays.
Editing a Route
To remove all waypoints:
1. From the Route Page, select the on-screen page Option Menu button
THUMB STICK IN to access the Option Menu.
Route Page
and press the
2. Highlight the ‘Remove All’ option and then press the THUMB STICK IN to remove all
waypoints from the list. When you see the prompt “Do you really want to remove all
waypoints from the route?”, select “Yes”.
To reverse the route:
1. From the Route Page, select the on-screen page Option Menu button
THUMB STICK IN to access the Option Menu.
and press the
2. Highlight the ‘Reverse Route’ option and then press the THUMB STICK IN to reverse the
order of waypoints in the list. To change the route back to the original order, repeat this
process.
Route Options
64
Features
To copy the route:
1. From the Route Page, select the on-screen page Option Menu button
THUMB STICK IN to access the Option Menu.
and press the
2. Highlight the ‘Copy Route’ option and then press the THUMB STICK IN to copy. The copied
route displays on the Routes Page and is named the same but followed by the numeral 1
(one). You may then rename and/or modify the copied route.
Routes Page
To delete the route:
1. From the Route Page, select the on-screen page Option Menu button
THUMB STICK IN to access the Option Menu.
and press the
2. Select ’Delete’ and then press the THUMB STICK IN. When you see the prompt “Do you
really want to delete route?”, select “Yes”.
To restore default settings for the route:
1. From the Route Page, select the on-screen page Option Menu button
THUMB STICK IN to access the Option Menu.
and press the
2. Select ’Restore Defaults’ and then press the THUMB STICK IN to restore factory settings.
To review a route point:
1. Select the point from the Route Points List and press the THUMB STICK IN to access the
Option Menu for the waypoint.
Route point review options
2. Highlight ‘Review’ and then press the THUMB STICK IN to display the Information Page.
3. Highlight the on-screen ‘OK’ button and then press the THUMB STICK IN to return to the
Route List.
65
Features
To insert a new point on the route list:
1. Select the row where you want the new point inserted before. Press the THUMB STICK IN.
Routes Page
2. Highlight ‘Insert’ and press the THUMB STICK IN to display the Find ‘N Go Menu and select
a new waypoint, city, exit, point of interest, etc.
3. With the new point highlighted, press the THUMB STICK IN to display the Information
Page for the new point and then select the on-screen ‘OK’ button to add it the route.
To remove a point from the route list:
1. Select the point that you want to remove from the Route Waypoints List and press the
THUMB STICK IN.
2. Highlight ‘Remove’ and press the THUMB STICK IN to remove the waypoint from the list.
To change a route point:
1. Select the waypoint that you want to change from the Route Waypoints List and press the
THUMB STICK IN.
2. Highlight ‘Change’ and press the THUMB STICK IN to display the Find ‘N Go Menu or
create a new waypoint and add it to the points list.
Route point review options
3. Select a new waypoint, access its Information Page and press the on-screen ‘Use’ button to
replace the old route waypoint.
To move a route point:
1. Select the point from the Route Points List and press the THUMB STICK IN.
2. Highlight the ‘Move’ option and press the THUMB STICK IN to select the waypoint.
3. Use the THUMB STICK to move the point up or down in the list. Press the THUMB STICK
IN to leave the waypoint in the new list order.
66
Adding or Editing from the Route Map Page
You can use the panning arrow with the Route Map Page displayed to add or edit route
waypoints.
Features
Routes Page
To add a point at either end of a route:
1. Select the Route from the Routes List. Press the THUMB STICK IN to display the Route
Page.
2. Highlight the on-screen ‘Map’ button at the bottom of the page and press the THUMB
STICK IN to display the Route Map Page.
3. Use the THUMB STICK to move the panning arrow to either end of the displayed route
until the end point is highlighted. Then press the THUMB STICK IN and select ‘Add Turns’.
This option appears only when highlighting the end point of a route.
4. Move the panning arrow to a map item or location where you would like to extend the
route and press the THUMB STICK IN to display the Information Page for the new point.
5. Press the on-screen ‘Use’ button to return to the map page and then press the THUMB
STICK IN again to place the new waypoint.
To add a route point within a route:
1. Follow steps 1 and 2 in the previous instruction.
2. Use the THUMB STICK to move the panning arrow to a route line. When the arrow
touches the line, the line becomes thin. Press the THUMB STICK IN to display the word
‘ADD’ next to the line.
3. Drag the line to a map item or other location where you want to establish a new waypoint
and then press the THUMB STICK IN to place the new waypoint. A waypoint information
page displays. Press the on-screen ‘OK’ button to save the new waypoint, then press it
again after returning to the Route Map.
67
Features
Routes Page
To review or remove a route point:
1. Select the Route from the Routes List. Press the THUMB STICK IN to display the Route
Page.
2. Use the THUMB STICK to highlight the desired route and press IN to display the Route
Page.
3. Use the THUMB STICK to move the map panning arrow to the point you want to review
and press IN.
Select ‘Review’ or ‘Remove’ and press IN again to either display the Information Page or
remove it from the route.
Select ‘Next’ and press IN again to view the next waypoint.
Navigating a Route
A Route can be navigated using the Map Page or the Navigation Page. The Map Page displays your movement, the route line, and waypoints on the route. The Navigation Page shows
compass direction and a bearing pointer.
To navigate a route:
Route Navigation
1. Select a route from the Routes List and then press the THUMB STICK IN.
2. Highlight the on-screen ‘Navigate’ button at the bottom of the page and then press the
THUMB STICK IN to begin navigating the route. The screen changes to the Navigation
Page.
3. Move to the Map Page to view the route and your current location.
4. Begin moving, watching directional information on the Navigation Page or your progress on
the Map Page.
68
Stopping Navigation
To stop navigation, highlight the ‘Stop Navigation’ option on either the Navigation or Map
page’s Option Menu or select the ‘Stop’ button on the Route Page.
Features
Routes Page
Data Fields for the Route Page
When navigating a Route, the data displayed in the data fields on the Route Page may be
customized to provide useful navigation information.
To select data field options:
1. Use the THUMB STICK to highlight a data field on the Route Page and then press IN to
display the data field options.
2. Use the THUMB STICK to highlight the desired option and press IN to select that option for
the selected data field.
Data field options for Route Page:
Distance to Point - The distance from your current location to a route waypoint.
ETA To Point - Estimated Time of Arrival at a route waypoint (in sequence).
ETE To Point - Estimated Time Enroute to a route waypoint.
Leg Course - The line of travel between two route waypoints.
Changing the Route Data Fields
Leg Distance - The distance between two route waypoints.
Leg Time - The time required to travel from a route waypoint to the next.
Pointer - Direction pointer to a route waypoint.
Sunrise At Point - Time of sunrise at a route waypoint.
Sunset At Point - Time of sunset at a route waypoint.
69
Features
Tracks Page
TRACKS PAGE OVERVIEW
The Rino 130 draws an electronic bread crumb trail on the Map Page as you travel along.
This bread crumb trail is the ‘Track Log’. The Track Log contains information about points
along its path, including time, and position. The Rino 130 uses this information to allow you
to navigate using the saved track. You may also save tracks from other Rino users as they communicate with you.
To open the Tracks page:
1. Access the Menu Page by using the on-screen menu button
or the PAGE button.
2. Select the Tracks icon and press the THUMB STICK IN. The Tracks page opens.
Tracks Page icon
To save and use a Track:
1. Access the Tracks page from the Main Menu.
Press the on-screen ‘Off’ button IN to pause track logging. When track logging is active the
‘On’ button appears to be recessed.
2. Highlight the ‘Save’ on-screen button and then press the THUMB STICK IN to display the
track log ‘Save Back Through’ list.
3. Use the THUMB STICK to select the time and date that you would like to save the track
through.
Tracks Page
70
4. Press the THUMB STICK IN to save the track log and display the Track Page. The Track
Page shows the track name (which can be renamed using the keyboard for data entry), the
total distance of the track, track area (if available), a ‘Show on Map’ option, and on-screen
buttons for ‘Map’, ‘OK’, and ‘Tracback’.
Using the TracBack Feature
The ‘TracBack’ feature allows you to return along a traveled path (or another Rino user’s
path) without marking any waypoints. When you are ready to return to where you started, the
Rino 130 takes you back by following the ‘Track Log’ that you left behind. You can save a total
of 20 tracks in the unit memory. The Track Log starts recording as soon as the unit gets a satellite location fix and the Track Log feature is turned on. When you no longer need a Track Log
you can press the on-screen ‘Clear’ button to remove it.
Features
Tracks Page
If you want to keep a record of a certain track log or use the ‘TracBack’ feature, it is recommended that you clear the Track Log before you start traveling. The percentage of memory
used by the current track log is displayed in a window at the top of the page. After the Track
Log is ‘Cleared’, it displays zero percent. When the display reaches 100%, the most recent track
points start to overwrite the least recent if the default setting ‘Wrap When Full’ remains selected
on the track log setup. To avoid losing track points you want, save the Track Log when it approaches the 99% mark. The active track log stores up to 10,000 points.
The Saved Track Page displays the track and it can also be displayed on the Main Map Page
as you navigate. You may save up to 20 tracks with 250 points per track in the unit. Saved
Contact tracks count towards this total. Tracks are marked BEGIN and END.
To use the TracBack feature:
1. Highlight the ‘Tracback’ button on the Tracks page and press the THUMB STICK IN. The
Tracback Menu options (‘To Beginning’ and ‘To End’) are displayed.
2. Highlight the desired option and press the THUMB STICK IN to enable.
3. Use the Map Page or the Navigation Page to navigate the Track.
71
Features
Tracks Page
Setting up the Track Log
You can set the track recording interval to Distance, Time, or Automatic. You can set the
Track display resolution to High, Medium, Low, and Lowest. You can also use the Option
Menu to delete all saved tracks.
To use Track Log Setup options:
1. Highlight the Tracks Page Option Menu button
THUMB STICK IN to display the menu.
at the top of the page and press the
2. Highlight the ‘Tracks Log Setup’ option and then press the THUMB STICK IN.
You can check the ‘Wrap When Full’ option by highlighting it and then pressing the THUMB
STICK IN. You can highlight the ‘Record Method’ and ‘Interval’ fields and press the THUMB
STICK IN to display their options. ‘Interval’ options change to accommodate the ‘Record
Method’ choices.
72
Proximity Points
The Proximity Page lets you define an alarm circle around a stored waypoint/contact position, and can be used to help you avoid dangerous areas or to alert you when you have strayed
too far away from other Rino users. Up to ten waypoints may be listed, with a maximum alarm
radius of 99.99 nautical or statute miles or kilometers. If entering a proximity alarm circle, a
‘Near Proximity Point <name>’ message appears. If leaving a proximity alarm circle, a ‘Leaving
Proximity Point <name>’ message appears.
Features
Proximity Page
To access the Proximity Page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Proximity.
Proximity Page icon
To add a proximity point:
1. Use the THUMB STICK to highlight an empty space on the Proximity list and press the
THUMB STICK IN to display the ‘Find ‘N Go’ screen. Highlight an item from the list and
press the THUMB STICK IN to open the item.
2. From the Review Page, select ‘Use’. Press IN again to begin entry of the proximity radius.
Use the THUMB STICK to enter a distance and press IN.
To clear one or all proximity point(s) from the list:
1. To clear a single alarm, use the THUMB STICK to highlight the proximity point to clear and
press IN. Choose ‘Remove’ and press IN.
2. To clear all proximity waypoints, highlight the Option Menu
‘Remove All’ and press the THUMB STICK IN.
and press IN. Choose
Proximity Waypoints Page
To turn proximity alarms on or off:
1. Use the THUMB STICK to highlight ‘Proximity Alarms’ and press IN to place a check mark.
73
Features
SATELLITE PAGE OVERVIEW
The Satellite Page provides a picture of satellite signal tracking, tells you when the unit is
ready for navigation, and shows your location coordinates.
Satellite Page
To access the Satellite Page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Satellite.
Satellite Page icon
Signal
Strength
Bars
Skyview
Graphic
Skyview graphic
The Skyview graphic represents a view looking up at the sky from your current location
showing satellites and their assigned numbers. The outer ring represents the horizon around
you. The inner ring represents a view above you at a 45° angle from vertical. The center
represents directly overhead. Signal Strength Bars for each satellite are shown to the left of the
Skyview. Satellites and their signals appear as hollow shapes until a signal is received and then
they appear darkened in. The stronger the signal, the taller the signal bar.
90°
Center dot - 90°
above the horizon
Inner ring- 45°
above the horizon
Satellite Page
Outer ring the horizon
45°
74
WAAS
The Wide Area Augmentation System (WAAS) capability produces a more accurate position
fix. When enabled (GPS set to ‘Normal’ and WAAS set to ‘Enabled’ through the System Setup
Page, also the interface must be set to something other than RTCM mode), this feature searches
for WAAS satellites near your location and then receives data for correcting differentials in the
GPS satellite signals. WAAS satellite numbers begin at number 33 or above and are displayed
on the Satellite Page. When differential correction data has been received for GPS satellites
(numbers 32 or below), a ‘D’ displays in the signal bar beneath the skyview. It is helpful to
orient the unit antenna toward the WAAS satellite shown in the skyview. To learn more about
the WAAS System, refer to the Federal Aviation Administration web site (http://gps.faa.gov/).
Because the Rino 130 relies on satellite signals to provide you with navigational guidance, the
unit’s view of the sky determines how fast you achieve navigational status. GPS signals do not
travel through heavy objects or people: For best results, keep the unit in clear view of the sky.
Features
Satellite Page
Satellite Strength
At least three satellite signals are needed to determine your location, otherwise the unit
displays a “Poor Satellite Reception” message with four options:
Use with GPS Off - Select this option if you want GPS off.
Satellite Page using WAAS.
New Location - Select this option if you have moved more than 600 hundred miles (from
where you last used the unit).
Restart Search - Select this option if today is not (date provided).
Continue Acquiring - Select this option if no other option applies. The unit will attempt to
gather GPS signals.
75
Features
Satellite Page
SATELLITE PAGE OPTIONS
Use With GPS Off - Use this option when you are indoors, your view of the sky is obstructed,
or you want to save battery power. You can enter data, create routes, etc., but cannot navigate
in this mode.
Track Up/North Up - You can orient the satellite skyview by selecting ‘Track Up’ (your direction of travel) or ‘North Up’ (the satellite skyview oriented to the north).
New Location - If you are more than 600 miles (from where you last used the unit), select the
‘New Location’ and then the ‘Use Map’ options to approximate your location. This gives the
unit reference information and speeds satellite acquisition.
To select the ‘Use With GPS Off’ option:
1. Use the THUMB STICK to highlight the Option Menu button
and then press it IN.
at the top of the page
2. Use the THUMB STICK to highlight the ‘Use With GPS Off’ option and then press it IN.
The Rino 130 stops tracking satellites and should not be used for navigation. However, the
next time you turn the unit on, it returns to Normal GPS operation.
Satellite Page Option Menu
To select ‘Track Up’ or ‘North Up’:
1. Use the THUMB STICK to highlight the Option Menu button
and then press it IN to display the Option Menu.
at the top of the page
2. Highlight either the ‘Track Up’ or ‘North Up’ option (depending on which is currently in use),
and press the THUMB STICK IN to activate.
76
Features
To enter a new location:
1. Use the THUMB STICK to highlight the Option Menu button
and then press it IN.
at the top of the page
2. Highlight ‘New Location’ and press the THUMB STICK IN to display choices of ‘Auto’ or
‘Use Map’.
Satellite Page
If you choose ‘Automatic’ the Rino 130 determines your new location automatically.
If you choose ‘Use Map’ a map page displays with instructions stating, “Point to your
approximate location and press ENTER”. Use the THUMB STICK to move the map pointer
to your location on the map and press the THUMB STICK IN.
77
Features
Setup Pages
SETUP MENU
The Setup Pages allow you to customize the Rino 130 to your personal preferences. You
can choose time settings, units of measure, display backlighting and contrast settings, heading
measurement, interface options and system operating mode.
By highlighting the icons on the Setup Menu and then pressing the THUMB STICK IN, you
can display the Setup Page for each of the menu items.
To access the Setup Menu
Setup Menu icon in
the Main Menu
Time Setup icon
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup. There are then several more icons to
choose from in the Setup Menu.
Time Setup Page
You can set the time to match your location or for a projected location anywhere in the
world.
To access the Time Setup page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Time icon to open the Time Setup page.
Time Format - Allows you to choose from 12-hour (like a standard clock with 12-hour AM
and PM cycles) or 24-hour time format ( a 24- hour cycle, also called Military Time).
Time Setup Page
78
Time Zone - Can be set to one of the eight US Time Zones, or 24 International Time Zones
(nearest city or geographical region). Select ‘Other’ so you can enter the UTC Time Offset.
Daylight Savings Time - Can be turned On or Off or set to Automatic.
To set the time:
1. Use the PAGE button to access the Main Menu.
2. Use the THUMB STICK to highlight the Setup Icon. Press the THUMB STICK IN to display
the Setup Menu.
Features
Setup Page
3. Use the THUMB STICK to highlight the Time Icon. Press the THUMB STICK IN to display
the Time Page.
4. Use the THUMB STICK to highlight the ‘Time Zone’ field. Press the THUMB STICK IN to
display the time zone list.
5. Highlight a time zone from the list and then press the THUMB STICK IN.
6. If you choose ‘Other’, you must enter a UTC offset value.
Units Setup icon
7. The correct time displays at the bottom of the page.
Units Setup Page
The Units features are best used by individuals with a working knowledge of map grids and
datums. To learn more about these subjects, visit the National Imagery and Mapping Agency at
http://www.nima.mil or inquire at your local library.
To access the Units Setup page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
Units Setup Page
3. Select the Units icon to open the Units Setup page.
79
Features
Setup Page
LORAN TD Page
in the Units Setup
Page
Position Format - Allows you to choose from different grid formats. The default position format, ‘hddd°mm.mmm’ displays the latitude and longitude in degrees and minutes and is most
commonly used. The following additional formats are available:
hddd.ddddd° - latitude/longitude in decimal degrees; hddd°mm.mmm’ - latitude/longitude in
decimal numbers; hddd°mm’ss.s” - latitude/longitude in degrees, minutes, seconds; British Grid;
Dutch Grid; EOV Hungarian Grid; Finnish Grid; German Grid; Icelandic Grid; India Zones;
Irish Grids; Loran TD; Maidenhead; MGRS; New Zealand; QNG Grid; RT90; South African Grid;
Swedish Grid; Swiss Grid; Taiwan Grid; US National Grid; UTM/UpS - Universal Transverse
Mercator / Universal Polar Stereographic grids; W Malayan RSO; and User UTM Grid.
LORAN TD Format
When creating new waypoints using LORAN TD coordinates, you must set the correct LORAN chain number and secondary stations in the Setup TD field before storing the
waypoint. After the waypoint is stored in unit memory, it always references the LORAN chain
number and secondary stations currently selected in the Setup TD field. If you enter a different
LORAN chain number, change the secondary stations, or offsets in the Setup TD field, the active waypoint information reflects those changes. Because the unit does not rely on the LORAN
signal for navigation, it can reference a different GRI chain and/or secondary stations and still
navigate to the location stored in memory.
To adjust the Loran TD settings, select ‘Loran TD’ as the Position Format to open the Loran
TD setup window. To change the settings of any fields, highlight the field, press the THUMB
STICK IN. When done, highlight ‘Save’ and press IN.
For more information on Loran TDs, you may download Garmin’s Loran TD Position Format
Handbook from the Garmin web site at http://www.Garmin.com/support/userManual.html.
80
Map Datum - Offers a selection of nearly all map datums in common use. Every map is based
on a map datum (a reference model of the earth’s shape) and is usually listed in the title block
of the map. If you are comparing GPS coordinates to a paper map, chart, or other reference,
the map datum in this field must match the horizontal map datum used to generate the map
or other reference. The default datum is WGS-84 (World Geodetic Survey 1984) and should
only be changed when using maps or charts specifying a different datum. If a map does specify
a datum, use the options list to find datums applicable to the region of the map, selecting the
one that provides the best positioning at a known point. If necessary, you also may choose the
‘User’ datum for custom designed grids.
Features
Setup Page
NOTE: The ‘User’ datum is based on a WGS-84-Local datum and is an advanced
feature for unlisted or custom datums. To learn more, check your local library or the
Internet for educational materials on datums and coordinate systems.
Distance/Speed - Choose from three units of measure to display your rate of travel.
Elevation/Vertical Speed - Choose from two units of measure to record your elevation and
vertical speed.
Pressure - Choose from millibars or Inches to measure the pressure.
Units Setup Page
Display Setup Page
You can adjust the amount of time that the backlighting feature stays on and adjust the
screen contrast.
Backlighting Timeout - Choose from Stays On, to delays of 15 seconds, 30 seconds, one
minute, or two minutes before timing out.
81
Features
Setup Page
Contrast Adjustment - Can be adjusted from light to dark using the slider adjacent to the
contrast bar.
To access the Display Setup page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Display icon to open the Display Setup page.
To set the backlighting timeout:
1. Highlight the Backlight Timeout field and then press the THUMB STICK IN.
2. Highlight the desired option and then press the THUMB STICK IN.
To adjust the contrast:
Display Setup icon
1. Highlight the contrast slider and then press the THUMB STICK IN.
Display Setup Page
2. Move the THUMB STICK up or down to move the slider to set the contrast.
Heading Setup Page
You can select the type of heading displays, the types of North References, or enter the
magnetic variation.
To access the Heading Setup page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Heading icon to open the Heading Setup page.
Heading Setup icon
Display - Allows you to choose from Cardinal Letters, Degrees or Mils.
Heading Setup Page
82
North Reference - You can choose from True, Magnetic, Grid or User options. If ‘User’ is
chosen, you must correct for the Magnetic Variation. The Electronic or GPS compass uses the
North Reference setting to create a bearing.
Switch to Compass Heading when Below - Enter the desired speed for the Rino 130 to
switch from using GPS to using the compass for guidance.
Features
Setup Page
For more than… - Enter a time limit to switch to the compass. When you travel at the speed
entered above for the time entered here, the Rino 130 switches from GPS to the compass.
To select either option:
1. Highlight the field and then press the THUMB STICK IN to display the options.
2. Highlight the option and press the THUMB STICK IN to activate.
Interface Setup Page
The Interface Settings Page allows you to choose from different input/output serial data formats. This feature is used when connecting to external NMEA devices, a DGPS beacon receiver,
a personal computer, etc. See the Appendix for using the Rino 130 with MapSource.
Interface Setup icon
To access the Interface Setup page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the Interface icon to open the Interface Setup page.
The available interface formats are:
Interface Setup Page
Garmin - The proprietary format used to exchange waypoint, track, and map data with a PC.
Use this setting for transferring data when using a MapSource product.
83
Features
Setup Page
Garmin DGPS - Allows DGPS input using a Garmin beacon receiver and a standard RTCM SC-104 and DGPS tuning.
NMEA In/NMEA Out - Supports the output of standard NMEA 0183 version 3.0 data. Use
this for real-time plotting with MapSource or 3rd party programs.
Text Out - Allows ASCII text output of location and velocity information without input capabilities.
RTCM IN - Allows DGPS input using a standard RTCM SC-104 format without output capabilities.
RTCM In/NMEA Out- Allows DGPS input using a standard RTCM SC-104 format and supports the output of standard NMEA 0183 version 3.0 data.
RTCM In/Text Out- Allows DGPS input using a standard RTCM SC-104 format and simple
ASCII text output of location and velocity information.
None - Provides no interfacing capabilities.
Interface Setup Page
If ‘Garmin DGPS’ or ‘RTCM In/NMEA Out’ format is selected, additional fields are provided
to control a Garmin differential beacon receiver (e.g. GBR 23) directly from your unit. Tuning is
automatic with ‘Scan’ or you can enter the beacon frequency and bit rate when you select ‘User’
from the Beacon list to manually tune the receiver. Refer to the beacon receiver instructions.
To select a serial data format:
1. Highlight the Serial Data Format field and then press the THUMB STICK IN.
2. Highlight an option and then press the THUMB STICK IN to activate it.
84
System Setup Page
The System Setup Page allows you to change GPS operation modes, use the WAAS capabilities, turn the Message Beep and compass on or off, choose the battery type, and set the altimeter
calibration settings to automatic or manual. See the Appendix for WAAS capability information.
Features
Setup Page
To access the System Setup page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Setup.
3. Select the System icon to open the System Setup page.
The Option Menu
allows you restore defaults or display the current version of unit
operating software and the Unit I.D. Number. Software updates and instructions for downloading are available from the Garmin web site (www.Garmin.com).
System Setup icon
Choose one of the four GPS options other than ‘Normal’ to significantly save battery power.
The ‘Battery Saver’ mode reduces the rate of satellite signal position updating and the ‘GPS Off’
option stops satellite signal reception altogether. The ‘Demo Mode’ simulates navigation.
To change the battery type:
1. Use the THUMB STICK to highlight the ‘Battery Type’ field and then press IN.
2. Then use the THUMB STICK to select the desired option and press IN. Use the following
settings for different battery types:
BATTERY TYPE
SET UNIT TO
BATTERY TYPE
SET UNIT TO
Alkaline
Alkaline
Lithium (1.2V)
NiMH
NiMH
NiMH
Lithium (1.5V)
Alkaline
NiCad
NiMH
System Setup Page
85
Features
Calendar
Using the Calendar
This feature provides you with a monthly calendar with programmable reference notes.
You can display one monthly calendar at a time and add reference notes using the data entry
keypad. Days that are shaded have notes added. You can create reference notes for multiple
months and for months in years yet to come. You can record 100 notes with up to 18 characters each.
To access the Calendar:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Calendar.
To change the month and year:
1. Highlight the left or right arrows on either side of the date and press the THUMB STICK IN.
The left arrow shows past months/years and the right arrow shows future months/years.
To use the current month and year
1. Choose ‘Set To Current Date’ from the Option Menu
.
To create a reference note for a selected date:
Calendar Page
1. Use the THUMB STICK to highlight the day of the month and then press IN to display the
pop-up Menu (containing ‘New Note’, View Sun & Moon’, and View Hunt & Fish’).
2. Highlight and select ‘New Note’ to begin entering text from the keyboard.
Calendar options
86
Features
To edit or delete a note:
1. To edit or delete a note previously created, highlight the date and press the THUMB STICK
IN.
2. Select ‘Edit Note’, or ‘Delete Note’, from the pop-up menu. To complete the deletion of the
note, press the THUMB STICK IN when ‘Yes’ is highlighted in the pop-up window.
Calendar
3. To edit the note, change the desired characters using the keyboard as shown in the image
to the right. Press ‘OK’ when you are finished editing the note.
To delete notes by week:
1. Choose ‘Delete Notes...’ from the Option Menu
.
2. From the ‘Older Than..’ window, choose the desired option and press the THUMB STICK IN.
To view information for a date:
1. In the calendar, select the desired date using the THUMB STICK.
2. Review the note in the note window below the calendar.
3. Press the THUMB STICK IN to display the pop-up menu.
4. Select ‘View Sun & Moon’ to view the Sun & Moon Page for that date. Select ‘View Hunt &
Fish’ to view the Hunt & Fish Page for that date.
Editing a note
87
Features
Alarm Clock
Using the Alarm Clock
This feature provides an alarm for the system clock. Enter a time in the time field and turn
the alarm on and off from the control field menu. Remember to enter alarm times in the same
time format (UTC or local) you are using for your system. The unit must be on for the clock
alarm to work.
To access the Alarm Clock:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Alarm Clock.
To set an alarm clock time:
Alarm Clock icon
1. Use the THUMB STICK to highlight the time field and then press IN to display the
keyboard.
2. Use the THUMB STICK to enter the desired time, choose ‘OK’ and press IN.
To turn the alarm clock On/Off:
1. Use the THUMB STICK to highlight the Alarm Mode field and then press IN to display the
options.
2. Choose ‘On’ or ‘Off’ and press the THUMB STICK IN.
Alarm Clock Page
88
When the alarm sounds, a brief tone is heard (unless Message Beep is ‘Off’ under System
Setup) and “Alarm Clock” appears on the screen. Press the THUMB STICK IN to acknowledge
the alarm.
Using the Calculator
This feature provides you with all the basic functions of both of standard or scientific calculator. You can perform most calculations identified by the function symbols along the sides of
the keypad and can save the results temporarily in the memory. The memory is cleared either
manually or when you turn off the Rino 130.
Features
Calculator
To access the Calculator:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select Calculator.
To change calculator options:
1. Highlight the page Option Menu
and press the THUMB STICK IN to display the
‘Scientific/Standard’ and ‘Radian/Degrees’ options.
Calculator icon
2. Highlight the option you want to change and then press the THUMB STICK IN.
3. Use the THUMB STICK to move about the calculator, enter numbers, and perform
calculations.
Calculator Page
89
Features
Stopwatch
Using the Stopwatch
This feature allows you to use the unit as a stopwatch, including using it as a lap timer. You
may also have the unit record the lap time based on distance. For example, if you set the lap
distance to one mile, the unit records the time it takes you to travel one mile.
To access the Stopwatch:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select the Stopwatch icon.
Stopwatch icon
To use the Stopwatch:
1. Use the THUMB STICK to highlight the ‘Start’ field and then press IN. You may also press
the V (VOLUME) button to Start the stopwatch.
2. Use the THUMB STICK to highlight the ‘Stop’ field and then press IN. You may also press
the V (VOLUME) button to Stop the stopwatch.
3. To mark a lap, use the THUMB STICK to highlight the ‘Lap’ field and then press IN, with the
stopwatch running, . You may also press the Z (ZOOM) button to capture the lap time.
4. Reset the stopwatch when the timer is stopped. Use the THUMB STICK to highlight the
‘Reset’ field and then press IN. You may also press the Z (ZOOM) button to reset the times.
Stopwatch Page
90
Stopwatch Lap Options
You can set the stopwatch to ‘Lap by Distance’ so that each time a certain distance has been
travelled, the stopwatch automatically marks a lap. You can enter a specific lap distance by
selecting ‘Set Lap Distance’. To return to manually marking each lap, open the Option Menu
and select the ‘Lap by Button Press’ option.
Using the Sun & Moon Page
This feature provides you with a graphic display of both sun and moon positioning for a
certain date, time and location with times for sunrise, sunset, moonrise, and moonset.
Features
Sun & Moon
To access the Sun & Moon Page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select the Sun & Moon icon.
To set the date and time:
1. For the Date and Current Time, highlight each field, then press the THUMB STICK IN to
begin data entry of individual characters.
2. To display the current date and time, highlight the page Option Menu
and press the
THUMB STICK IN to display ‘Use Current Time’ and then press the THUMB STICK IN.
Sun & Moon icon
To set the location:
1. Highlight the Location field and then press the THUMB STICK to display the ‘New Location’
options list.
2. Highlight the option desired and then press IN on the THUMB STICK to activate. If you
choose ‘Current Location’ the field values displayed on the page displays your location. If
you choose ‘Use Map’, a map page displays. Use the map pointer to identify the desired
location and then press IN on the THUMB STICK. If you choose ‘Use Find ‘N Go Menu’
follow instructions in the Find ‘N Go section.
Sun & Moon Page
91
Features
Hunt & Fish
Using the Hunt & Fish Page
This feature provides you with a listing of best times for hunting and fishing for a chosen
location and date.
To access the Hunt & Fish Page:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select the Hunt & Fish icon.
To set the date:
1. Highlight the date field and then press IN on the THUMB STICK to begin data entry of
individual characters.
Hunt & Fish icon
2. To display the current date, highlight the page Option Menu and press the THUMB STICK
IN to display the ‘Use Current Date’ option and then press the THUMB STICK IN.
To set the location:
1. Highlight the Location field and then press IN on the THUMB STICK to display the ‘New
Location’ options list.
2. Highlight the option desired and then press IN on the THUMB STICK to activate. If you
choose ‘Current Location’ the field values displayed on the page reflect the times at your
current location.
Hunt & Fish Page
3. If you choose ‘Use Map’, a map page displays. Use the map pointer to identify the desired
location and then press IN on the THUMB STICK. If you choose ‘Use Find ‘N Go Menu’
follow instructions for using the Find ‘N Go Menu.
NOTE: The times displayed are the recognized best and good times for hunting and
92
fishing. Be certain that they are not in conflict with state and local game laws, which
may vary from location to location. It is your responsibility to know and abide by
these laws.
Using the Area Calculator
This feature provides you an area calculation as you move about a location or view a saved
track. The area calculation displays in acres, hectares, and square feet, square yards, square
meters, square kilometers, and square miles.
Features
Area Calculator
To access the Area Calculator:
1. Press the PAGE button or the Menu icon
to open the Main Menu.
2. In the Main Menu, scroll down and select the Area Calculator icon.
To calculate the area:
1. Be sure the Rino 130 has a GPS fix.
2. Press ‘Start’ when you are ready to begin.
2. Begin walking or traveling the perimeter (edge) of the area you want to measure.
Area Calculation icon
3. Use the THUMB STICK to stop the calculation when you have traveled the desired distance.
4. Use the THUMB STICK to store the area as a saved track.
To review the area of a saved track:
1. On the Tracks page, highlight a Saved Track.
2. Press the THUMB STICK IN to see a map with the area shown in a data field at the bottom.
Area Calculation Page
93
Features
Games
Games Menu icon
Games Menu
GAMES MENU
The Games Page includes Memory Race, Waypoint Bomber, Clothesline, Assimilation and
Beast Hunt. Highlight the appropriate icon and then press the THUMB STICK IN to play the
desired game. Brief instructions are displayed when you start each game. All players must be
on the same channel/squelch code to play.
Memory Race
Be the first to clear the board by matching all of the two symbols sets together. Each symbol
is in a square (you can adjust the size) that you need to walk or travel to. Once your position
appears in a square, highlight ‘Open’ at the bottom of the screen and press the THUMB STICK
IN . Play by yourself or race against others. Press Page to quit at any time.
Memory Race
To adjust the Grid Size or Square Size:
1. Highlight the ‘Grid Size’ or Square Size’ field and press IN on the THUMB STICK.
2. Choose the desired size and press IN.
3. Highlight ‘Start’ and press IN to begin the game.
94
Waypoint Bomber
In this game, it is good to stay on the move! Two or more players attempt to “bomb” each
other. Move your cursor around on the map page using your THUMB STICK. When you
think an opponent is close to your cursor, drop a bomb. The receiving radio shows an ‘Incoming” message. If the receiving radio is within the blast circle (about 45 feet), it displays a message that you have been hit. You must wait 30 seconds between shots to reload. Either have a
timed game with the winner being the one with the least amount of hits on their radio, or play
until someone gets a specified number of hits (that person loses).
Features
Games
Waypoint Bomber
HINT: Mark stationary objects such as trees and poles, and drop a bomb when an
opposing player is near that object! Adjust the rules to your liking!
•
To fire at the cursor location, press the THUMB STICK IN.
•
To fire at your current location, press the TALK button.
•
Press CALL to view the scoreboard at any time.
•
Press PAGE to quit the game at any time.
95
Features
Games
Clothesline
Team members select the same user symbol and then attempt
to “hit” or “clothesline” other players by pressing the TALK button
when an opposing team member is between them. You may also
mark a point and assign it a symbol to be used as a stationary team
member. Wait 30 seconds between attempts. Press CALL to view
the score and PAGE to quit the game.
Clothesline
Assimilation
Beast Hunt
96
Assimilation
Think of this as a high-tech game of tag. Team members select the same user symbol and
then attempt to assimilate others into their team by getting within 30 feet of them and pressing
the TALK button. Press CALL to show the score and PAGE to quit the game. You can set a
time limit so the largest team wins, or play until the other team is completely assimilated. Set
your own rules and enjoy!
Beast Hunt
The objective is to find and kill the beast with an arrow before it incinerates you or you fall
into one of several pits while navigating a maze of platforms. You can be transported by slides
that curve or move diagonally. When you think you know where the beast is press the THUMB
STICK IN to initiate aiming when you are in an adjacent spot. With the THUMB STICK, point
the arrow in the direction where you think the beast is and press the THUMB STICK IN to fire.
When you lose a game, the layout of hazards, slides, warning platforms, and the location of the
beast is shown. A scoreboard keeps track of your wins and losses. Press PAGE anytime during
the game for further instructions, to turn the sound On/Off, or to quit.
WHAT IS FRS?
FRS, or Family Radio Service, is a UHF radio frequency band allocated by the FCC for
general public use. The operating frequency ranges from 462.5625 to 467.7125 MHz, with a
maximum transmitting power of one half watt. FRS radios are small and lightweight, making
them ideally suited for outdoor activities. FRS radios typically feature a half watt of transmit
power. You can expect your FRS radio to offer reliable operation at a one-mile range. If the
area between you and another FRS operator is free of obstructions, operation up to two miles
can be achieved. FRS radios broadcast on one of 14 channels, each with a specific frequency
within the FRS band.
Appendix
FRS Explained
The use of FRS radios does not require a license. FRS was intended for use by families and
small groups as an inexpensive means of two-way voice communication. FRS is intended for
use throughout the United States, its territories and possessions. It may also be used in Canada.
FRS is not approved outside of these areas and may interfere with local government communication frequencies (fire, police, etc.).
FRS Features
More sophisticated FRS radios also include call functions, squelch codes, channel scan
features, and voice scramble capabilities. Call functions allow you to push a Call button on
the radio to alert other radios set on the same channel. This feature generates a call tone and is
handy in a noisy environment where the tone is easier to initially identify than plain speech.
Squelch codes allow you to selectively block out other FRS users that are not part of your
group. They will still be talking with others in their own group, but you will not hear them on
your radio. They may or may not hear you and members of your group on their own radios.
Squelch codes act as a filter, blocking your FRS radio from hearing other unwanted FRS users.
97
Appendix
FRS Explained
Remember though, these are public-use frequencies and everyone has a right to talk or listen in.
Channel scan allows your FRS radio to scan all FRS frequencies for signals. After scanning briefly to see what channels other users are on, simply set your FRS radios to an unused
channel and enjoy less interference. For greater privacy, some FRS radios have a voice scramble
feature. This feature causes your message to sound garbled to other FRS users that are not part
of your group. However, it does not guarantee your conversations will be 100 percent private
and secure. Other casual FRS users will not hear your messages, but users with similar radios
or more technically-oriented users can still monitor your conversations.
FRS limitations
If you are operating in an urban environment or in varying terrain, some features (such as
canyons or mountains) act as obstructions limiting the maximum reception range of your FRS
radio. The UHF FRS frequencies are “line of sight”, meaning that the signals do not follow the
surface of the earth, but instead radiate in a straight line from the transmitting antenna. If there
is an obstruction between the transmitting FRS radio and the receiving FRS radio, the signal
will not be received. Smaller obstructions, such as trees, cars and even crowds of people cause
some loss of signal, resulting in reduced maximum range.
GMRS
The use of a GMRS (General Mobile Radio Service) radio requires an FCC license. The
operating frequency of GMRS ranges from 462.550 to 467.725 MHz. GMRS use is currently
not allowed in Canada and is disabled on Canadian models. GMRS radios can use repeater
channels and repeater towers to extend the range of the operation. A repeater tower simultaneously receives GMRS signals on a 467 MHz frequency and then rebroadcasts the signal on a 462
MHz frequency. Refer to the Frequency Charts for a complete list of each channel’s frequency.
98
Appendix
Physical
Case:
Fully-gasketed, high-impact plastic alloy, waterproof to IPX7 standards
(waterproof to one meter for 30 minutes)
Size:
4.5” H x 2.3” W x 1.6” D; 7” H with antenna
(11.4 x 5.8 x 4.1; 17.8 cm)
Weight:
Approx. 7.6 ounces (236 g) with batteries
Temperature Range:
-4° to 158° F (-20° to 70° C) (operating range)
Display:
1.4” H x 1.4” W (3.6 cm x 3.6 cm)
60 x 160 pixels, high-contrast LCD
Specifications
Performance
GPS Receiver:
WAAS Enabled, Differential-ready, 12 parallel channel
Acquisition time:
Approx. 15 seconds (warm start)
Approx. 45 seconds (EZinit/cold start)
Approx. 5 minutes (First Time/AutoLocate®)
Update Rate:
1/second, continuous
GPS Accuracy:
<15 meters (49 ft) RMS, 95% typical1
DGPS (USGC) Accuracy: 3-5 meters (10-16 ft), 95% typical with DGPS corrections2
DGPS (WAAS) Accuracy: <3 meters (10 ft), 95% typical with DGPS corrections2
Velocity Accuracy:
0.05 meter/sec steady state
Dynamics:
Performs to specifications to 6 g’s
Interfaces:
NMEA 0183, RTCM 104 (for DGPS corrections) and
RS-232 for PC interface
Antenna:
Quad-helix
99
Appendix
Radio
Channels:
1–14 FRS,
15–22 GMRS (GMRS requires FCC license)
1–7 Weather Radio channels
Squelch Codes:
1–38
Range:
UP to 2 miles on FRS; up to 5 miles on GMRS
Radio Output Power:
FRS 0.5 watt; GMRS 1.0 watt
Specifications
Power
Input:
Three 1.5 Volt AA batteries3
Battery Life:
GPS only: up to 41 hours;
FRS only: up to 20 hours;
FRS, GPS, and sensors: up to 14 hours4
Specifications are subject to change without notice.
1
Subject to accuracy degradation to 100m 2DRMS under the U.S. DoD-imposed Selective Availability program.
2
With optional Garmin Differential Beacon Receiver Input (such as Garmin GBR 23).
3
The temperature rating for the Rino 130 may exceed the usable range of some batteries. Alkaline batteries can rupture
at high temperatures. External power can only be applied using the Garmin Auto Power Adapter or PC Interface
Cable with Auto Power Adapter. These cables contain a 12 Vdc to 4.5 Vdc voltage regulator. Modifications or other
applications voids the product warranty. Alkaline batteries lose a significant amount of their capacity as temperature
decreases. Use lithium batteries when operating the Rino 130 in below-freezing conditions. Extensive use of screen
backlighting and the radio significantly reduces battery life. Different brands of batteries vary in performance.
4
5, 5, 90 Duty Cycle - 5% receive with audio unmuted, 5% transmit and 90% standby (receive with audio muted)
100
To obtain accessories, see your local dealer or visit the Garmin web site at www.Garmin.com.
Appendix
12-volt Adapter Cable: Provides unit power from an automobile cigarette lighter.
2.5 to 3.5 mm Jack Adapter: Allows you to use 3rd party headsets with your Rino unit.
Accessories
Bash Guard Kit: Helps protect the Rino’s edges against hard shocks. Includes 2 bash guards,
quick-release neck lanyard, and belt clip.
Carrying Case: Protects the Rino and permits use while in the case.
Earbud with PTT (Push To Talk) Mic: Earbud and a clip-on mic with PTT button.
Flexible Ear Receiver: Comfortable earpiece for better hearing ability of your Rino.
Headset with VOX Boom Mic: Hands-free at it’s best! Utilize the Rino’s VOX (Voice Operated
Transmission) feature with this headset and voice activated boom mic.
Instructional Video: For getting accustomed to your Rino basic operations quickly.
MapSource Map Data CD-ROMs: An excellent tool for creating waypoints and routes on
your PC and downloading them to your Rino.
NiMH Battery Charger: Includes NiMH battery charger and 4 AA NiMH batteries.
PC Data Cable and 12-volt Adapter: Allows transfer of waypoints and routes from a PC to
the Rino and provides unit power from an automobile cigarette lighter.
Rail/Handlebar Mount: Allows you to mount your Rino on most rails or handlebars.
Suction Cup Mount: Allows you to mount your Rino on most smooth surfaces or windscreens.
101
Appendix
MapSource Setup
Transferring MapSource Map Data
If you have purchased a Garmin MapSource CD-ROM mapping program you may want
to transfer detailed map data before beginning use, to provide your unit with maximum Find
features and mapping capability. The Rino 130 accepts up to 24 MB of map data from most
MapSource products. It is not possible to transfer 3rd party maps into Garmin products.
You cannot view multiple types of MapSource data in the same location at the same time
(one replaces the other if there is an overlap). When you leave a MetroGuide area for example
and enter the area of a topographic map, the display changes to contour lines. The same is true
when moving from a topo map to a MetroGuide map. The BlueChart maps are at the top of the
hierarchy and will replace any other map information. Here is the list of the hierarchy for your
reference:
1. BlueChart
2. MetroGuide
3. Fishing Hot Spots
4. Points of Interest
5. U.S. Waterways & Lights
6. U.S. Topo
7. Roads and Recreation
8. WorldMap
Map data transfer requires the use of a PC, a Garmin MapSource CD-ROM, and the PC
Interface Cable with RS-232 serial port connector supplied with this unit. Follow detailed
instructions for data transfer in the MapSource User’s Manual.
102
To setup for data transfer:
1. Remove the Power/Data Port cover on the back of the unit by lifting up on the protective
cover on the back of the unit.
2. Connect the serial port connection on the cable to the PC serial port.
Appendix
MapSource Setup
3. Connect the remaining cable connector to the back of the Rino 130 by orienting the slot on
the connector with indexing bar on the back of the unit. Then, slide the connector in place.
Be sure that the cable is pushed all the way into the back of the unit.
4. Turn on the Rino 130 and follow instructions for map data transfer provided in the
MapSource User’s Manual. See also the Interface Setup Page section for unit interface
settings.
103
Appendix
GPS Troubleshooting Guide
To resolve problems that cannot be remedied using this guide, contact Garmin Customer
Service at 913-397-8200 or 800-800-1020.
Symptom
Probable Cause
Remedy
Unit does not turn On.
Batteries are exhausted.
Batteries may be installed backwards.
You are pressing and releasing the Power button.
Batteries may be nearly exhausted.
The unit’s view of satellites is obstructed.
Your view of the satellite is obstructed or you are
located too far from satellites currently in service for the
Americas.
System GPS operation is set to something other ‘Normal’
and/or interface setting is for RTCM.
Replace batteries.
Reinstall batteries.
You must press and hold the Power button for 2 seconds.
Replace batteries.
Move to a location with a clear view of the sky.
Move to a location with a clear view and point the unit
antenna in the direction of the satellite.
Cannot obtain a differential position from WAAS.
You have not collected enough information from the
WAAS satellite.
Wait 10–20 minutes for the initial collection, then 1–2
minutes afterwards.
Cannot access Point of Interest, Street, or Intersection
Find Lists.
MetroGuide map data is not activated.
Access the Map Setup ‘Map’ option and activate the check
box.
Cannot view a track being laid down on the map page
when traveling.
The Track Log feature is turned Off.
Access the Tracks Page, highlight the ‘On’ button and
press the THUMB STICK IN.
Cannot see the panning arrow on the Map Page easily.
There is too much map clutter or the scale is such that
map features are too densely displayed
Use the Map Page Setup Page to reduce map clutter or
change the map scale.
Cannot exit a menu or page by moving the THUMB
STICK to the LEFT.
Some menus and pages have an ‘X’ (Exit) on-screen button in the upper right corner.
Highlight the on-screen button and then press the
THUMB STICK IN.
Unit does not turn On, even with new batteries.
The unit turns On, then turns Off.
It takes more than ten minutes to get a location fix.
Cannot access a WAAS system satellite after 2 to 5
minutes.
104
Set system GPS to ‘Normal’ and interface to other than
RTCM. Or simply turn off WAAS.
Appendix
Radio Troubleshooting Guide
To resolve problems that cannot be remedied using this guide, contact Garmin Customer Service at 913-397-8200 or 800-800-1020.
Symptom
Probable Cause
Remedy
Talk key may not be fully depressed.
Press and hold TALK key until done talking.
Radio not transmitting.
FRS/GMRS Radio feature may not be On.
Turn radio On.
Incorrect channel/Squelch Code setting.
Make sure other radios are on the same channel and
Squelch Code.
Messages not being received by others.
Out of radio range or obstructions.
Decrease distance between radios.
Limited talk range.
Natural or man-made obstructions can decrease range.
Decrease distance between radios or obtain a better line
of sight between radios.
You can hear others, but they cannot hear you or you see You are on the same channel, but a different Squelch
If you are using Squelch Code zero (0), you will hear all
an incoming transmission, but nothing is heard.
Code.
transmissions on that channel. Use the same Squelch
Code (1–38) as the other party or use ‘Scan’ to find what
Squelch Code they are on.
Message garbled.
Scramble option is enabled.
Both radios need to have this feature set the same (Rino
110 units do not have).
Too many unwanted conversations being heard.
Too many users on channel or Squelch Code is set to
Switch to a different channel and/or use Squelch Code
zero.
other than zero (1–38).
Radios too far apart or too close Obstructions in radio
Keep radios at least 3 feet apart. Obtain better line of
line of sight.
sight between radios.
Interference or static.
Interference from other electronics.
Shut off other devices or move away from interfering area.
Cannot transmit location.
Could be one of a few things: Your view of the satellite is Move to a location with a clear view of the sky. Enable
obstructed and a GPS fix is not available. ‘Send Location’ ‘Send Location’. Wait 30 seconds between location
is off. 30 seconds have not elapsed since last location
transmission. Enable GPS.
transmission. GPS is set to Off.
Keylock is enabled
None of the keys except TALK will work.
Hold PAGE for 5 seconds to release keylock..
105
Appendix
Data Field Definitions
The following data field options are available on the Map, Navigation, Altimeter, and Trip
Computer Pages.
Ambient Pressure - The uncalibrated current pressure. (Altimeter Page Only.)
Average Ascent - The average vertical distance of ascents. (Altimeter Page Only.)
Average Descent - The average vertical distance of descents. (Altimeter Page Only.)
Barometer - The Calibrated current pressure. (Altimeter Page Only.)
Bearing - The direction from your current location to a destination.
Course - The direction from your starting location to a destination.
Current Destination - The next waypoint on your route.
Current Distance - The remaining distance to your next waypoint.
Current ETA - The estimated time of day you will arrive at your next waypoint.
Current ETE - The estimated time needed to arrive at the next waypoint on your route.
Elevation - The altitude (height) above or below sea level.
Final Destination - The last waypoint on your route.
Final Distance - The remaining distance to your final destination.
Final ETA - The estimated time of day you will reach your final destination.
Final ETE - The estimated time needed to reach your final destination.
GPS Accuracy - The estimated accuracy of the GPS signal.
Heading - Your moving direction.
Location (lat/lon) - Your current GPS position. (Trip Computer Page Only.)
Location (selected) - The lat/lon of point defined on map. (Trip Computer Page Only.)
Maximum Ascent - The maximum ascent rate in feet per minute. (Altimeter Page Only.)
Maximum Descent - The maximum descent rate in feet per minute. (Altimeter Page Only.)
106
Maximum Elevation - The highest elevation reached. (Altimeter Page Only.)
Appendix
Maximum Speed - The maximum speed the unit has moved.
Minimum Elevation - The lowest elevation reached. (Altimeter Page Only.)
Moving Avg. Speed - Average speed of the unit while moving.
Data Field Definitions
Odometer - A running tally of distance travelled, based upon the distance between second-bysecond position readings.
Off Course - The distance left or right you are from the original course (path of travel).
Overall Avg. Speed - Your average speed.
Pointer - Indicates the direction to the next destination.
Speed - Display rate of travel in miles per hour, kilometers per hour, or nautical miles per hour.
Sunrise - The time at which the sun rises on this day.
Sunset - The time at which the sun sets on this day.
Time of Day - The time for the selected time zone.
To Course - The compass direction you must go in order to get back to the original course.
Trip Odometer - A running tally of distance travelled since last reset.
Trip Time - Moving - A running tally of movement time elapsed since last reset.
Trip Time - Stopped - A running tally of stopped time elapsed since last reset.
Trip Time - Total - A running tally of all time since last reset.
Total Ascent - The total distance ascended. (Altimeter Page Only.)
Total Descent - The total distance descended. (Altimeter Page Only.)
Turn - The angle difference (in degrees) between the bearing to your destination and your current
line of travel. ‘L’ means turn Left. ‘R’ means turn Right.
Velocity Made Good - The speed at which you are closing on a destination along a desired course.
Vertical Speed - Your rate of altitude gain/loss over time.
107
Appendix
Interface Information
Interface Information
Interface formats are selected in the Setup Interface Page. See also the MapSource Setup section of this Appendix for information on using the Rino 130 with MapSource. The input/output
lines on your Rino 130 unit are RS-232 compatible, allowing easy interface to a wide range
of external devices, including PC’s, differential beacon receivers, marine autopilots, and /or a
second GPS receiver.
The NMEA 0183 version 3.0 interface format is supported by the Rino 130 and enables the
unit to drive up to three NMEA devices.
NMEA 0183 VERSION 3.0 APPROVED SENTENCES:
GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPBOD
GARMIN PROPRIETARY SENTENCES:
PGRME (estimated error), PGRMM (datum string), PGRMZ (altitude), PSLIB (beacon
receiver control)
DGPS (Differential GPS) corrections are accepted in RTCM-SC-104 version 2.0 format
through the ‘Data IN’ line. The Garmin GBR 21 and GBR 23 are the recommended beacon
receivers for use with the Rino 130. Other beacon receivers with the correct RTCM format may
be used, but may not correctly display status or allow tuning control from the GPS unit.
The Rino 130 may be hard-wired to a serial connector using a Data Only Cable. Refer to
the wiring diagram and the Rino 130 unit data connection illustrated below.
The PC Interface Cable provided with this unit allows you to connect your Rino 130 to a
PC-compatible computer’s serial port.
108
Appendix
FRS Frequency Chart
Channel #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Transmit Frequency
(MHz)
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
Receive Frequency
(MHz)
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
Channel Description
FRS 1, GMRS Interstitial 1
FRS 2, GMRS Interstitial 2
FRS 3, GMRS Interstitial 3
FRS 4, GMRS Interstitial 4
FRS 5, GMRS Interstitial 5
FRS 6, GMRS Interstitial 6
FRS 7, GMRS Interstitial 7
FRS 8
FRS 9
FRS 10
FRS 11
FRS 12
FRS 13
FRS 14
Weather Radio Frequency Chart
Channel #
WX 1
WX 2
WX 3
WX 4
WX 5
WX 6
WX 7
Transmit Frequency
(MHz)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Receive Frequency
(MHz)
162.550
162.400
162.475
162.425
162.450
162.500
162.525
Channel Description
NOAA 1 (Weather Radio)
NOAA 2 (Weather Radio)
NOAA 3 (Weather Radio)
NOAA 4 (Weather Radio)
NOAA 5 (Weather Radio)
NOAA 6 (Weather Radio)
NOAA 7 (Weather Radio)
Frequency Charts
NOTE: If you plan to purchase
FRS radios from third party
manufacturers be aware that
there are CTCSS differences in
some radios. Some of the tones
on one radio may not be available on other radios. Charts
showing the different Squelch
Codes and manufacturers can
be located on the Internet.
NOTE: GMRS is not currently
approved for use in Canada.
For use in countries outside of
the U.S., please check with that
government for any restrictions
on FRS or GMRS use.
109
Appendix
Frequency Charts
NOTE: GMRS is not currently
approved for use in Canada.
For use in countries outside of
the U.S., please check with that
government for any restrictions
on FRS or GMRS use.
110
GMRS Frequency Chart
Channel #
15
16
17
18
19
20
21
22
15R
16R
17R
18R
19R
20R
21R
22R
Transmit Frequency
(MHz)
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
467.5500
467.5750
467.6000
467.6250
467.6500
467.6750
467.7000
467.7250
Receive Frequency
(MHz)
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
Channel Description
GMRS Primary 1
GMRS Primary 2
GMRS Primary 3
GMRS Primary 4
GMRS Primary 5
GMRS Primary 6
GMRS Primary 7
GMRS Primary 8
GMRS Repeater 1
GMRS Repeater 2
GMRS Repeater 3
GMRS Repeater 4
GMRS Repeater 5
GMRS Repeater 6
GMRS Repeater 7
GMRS Repeater 8
A
Accessories 101
Accuracy 99
Acquisition time 99
Address 57
Add to Route 50, 51, 53, 54, 56
Alarm 73, 88
Alarm Clock 88
Alert’ 15, 60
Alkaline 85
Altimeter Page 35, 35–39
Calibrate 36
Options 36
Overview 35
Reset 36
View Points 36
Zoom Ranges 36, 37
Altitude 35–39
Arriving at Destination 62
Arrow 25
Ascent 35, 39, 106
Attractions 55
Auto Zoom 27
B
Barometric Pressure 36, 37, 39
basemap 1
Battery icon 4
Battery Life 100
Battery types 85
Bearing 30
Bearing Pointer 30, 31, 32, 62
Big Compass 32
BlueChart 102
Bread crumb trail 70
Broken signals 16
Buttons Locked 44
By Name 49, 50, 53
C
Calculator 89
Scientific 89
Standard 89
Calendar 86
Note 86
Calibrate
Altimeter 39
Compass 32, 34
Call 97
Call Tone 14
Cartography 1
CDI 31
Chain 80
Change Route 64
Change scales 23
Change the battery type 85
Channel 8
Index
channel
Weather Radio 15
Circle 73
City 53
Clock 88
Code 8
Compass 34, 85
Calibrate 34
Off 34
On 34
Ring 30, 31
Contact 18, 52
Copy
Route 65
Course Deviation Indicator 31
Course Pointer 31, 32
Create a direct route 62
Create Waypoint 45, 46
CTCSS 8, 109
Current location 45
Defaults 2, 24, 32, 36, 40, 65, 85
Delete Waypoint 48
Descent 35, 39, 106
Detail 27
DGPS 108
Direct route 62
Display Mode 28
Distance 29
D
F
Data Fields 26, 32, 38, 39, 69
Definitions 106, 107
For Route Page 69
Data Transfer 103
E
Editing 47
Electronic Compass 34
Elevation 35, 36, 37, 39
Cchanges 37
Changes 35
Plot 37
Emergency & Govt 55
Enable
Peer-to-peer 12
Entertainment 55
Exit 54
Family Radio Service 1, 97
FCC 97
FCC license 98
111
Index
Fields, Data 39
Finding
Address 57
City 53
Contact 52
Exit 54
Intersection 57, 58
Point of Interest 55
Find ‘N Go 48–94, 49, 49–94,
62, 64
Fishing Hot Spots 102
Fishing information 92
Food & Drink 55
Frequency Charts 109, 110
FRS 1, 5, 8, 97, 109
H
G
L
Games 94
GARMIN sentences 108
General Mobile Radio Service 1
GMRS 1, 5, 8, 13, 97
Goto 50, 51, 52, 53, 54, 55, 62
GPS Off 16, 75
GPS On 16
GPS status 16
GRI chain 80
112
Headset 13
Hunting Information 92
Hunt & Fish 50, 51, 53, 54, 56, 92
I
Icons 4
Informational Picture 16
Initialize 5
Interfaces 99
Interface formats 108
Intersection 57, 58
IPX7 1
K
Keylock 3, 44
Land 28
Lap 90
Last Found Place 59
Line of sight 98
Lithium 85
Lock
Buttons/Keys 44
Buttons/keys 3
Direction 33
on Road 27
Lodging 55
LORAN TD Format 80
M
Main Display Pages 2
Main Menu
Overview 41
Page Sequence Setup 43
Manmade Places 55
Manually calibrate the altimeter 39
MapSource 1, 22, 57, 63, 84
Setup 102
Map Data 57, 102
Setup 28
Map Detail 27
Map Features Setup 28
Map Page 22
Map Data Setup 28
Map Features Setup 28
Options 24
Overview 22
Pan Map 24
Restore Defaults 24
Scale 23
Setup Map 24, 27
Text Setup 28
Tracks Setup 28
Map pointer 25
Map Setup options 27
Mark Waypoint Page 45
Measure Distance 24, 29
Message 61
Beep 85
Tone 14
MetroGuide 102
Microphone 13
Monitor 9
Move a waypoint 48
Mr. Mark Waypoint 16
My ID 6
N
Name 6
Navigate 31, 68
Navigation Page 30
Bearing Pointer/Course Pointer
32
Big Compass 32
Calibrating the Compass 34
Data Fields 32
Navigate 31
Options 32
Restore Defaults 32
Sight ‘N Go 33
Stop Navigation 32
Nearest 50, 53, 54
Near Map Pointer 53
New Contact 18
New Location 76, 77
NiCad 85
NiMH 85
NMEA 0183 108
North heading 27
North Up 27, 76
Note 61, 86
O
On-screen Button 39
On/Off Tone 14
Operating the Rino 3
Options Menu 3
Orientation 27
P
Page Sequence Setup 43
Pan Map 24, 25
PC 102, 108
PC Interface Cable 102
Peer-to-Peer 12, 13, 16, 18
PIT 13
Plot
Over Distance 36
Over Time 36
Page 37
Points of Interest 55, 56, 102
Poll location 52
Postal Code 57
Pressure 37
Changes 35
Plot 36, 37
View Plot 37
Program a data field 26, 39
Project Waypoint 33, 47, 50, 51,
52, 53, 54, 56
Proximity alarms 73
R
Radio 15
Radio Page 5
Channel 8
Code 8
Informational Picture 16
Monitor 10
Overview 5
Scan 9
Setup Radio 12
Setup Scanlist 14
Setup Tones 14
Weather Radio 15
Radio transmission status 16
Rate of ascent 35
Re-Sight 33
Recently Found Places 59
Reference note 86
Reposition Here 50, 51
Index
Reset 36, 38, 90
Restore Defaults 24, 36, 40
Reverse Route 64
Review
Route 65
Ring Tone 14
Roads and Recreation 102
Roger Tone 14
Routes 63
Copy 65
Create 63
Data Fields 69
Delete 65
Edit 64
Navigate 68
Remove waypoints 64
Restore defaults 65
Reverse 64
Review 65
Use 63
S
Satellite Page 22, 74
GPS Off 75
New Location 76
North Up 76
Options 76
Skyview 74
Track Up 76
Save as a Waypoint 53, 54, 56
Scales 23
Scan 9, 98
Scanlist 9, 11, 14
Scan Codes 9
Scientific calculator 89
Scramble 12, 98
Send
Location 18, 20, 50, 51, 52, 53,
54, 56
Note 61
Your location 18
Services 55
Set
Alarm clock 88
Proximity 50, 51, 52, 53, 54, 56
Scanlist 9
Setup
Map 24, 27
Menu 78
Page 78
LORAN TD Format 80
113
Index
Units 79
Radio 12
Scanlist 14
TD field 80
Time Page
Time 78
Tones 14
Message 14
On/Off Tone 14
Shopping 55
Shortcut Menu 3, 44–94, 46, 49
Overview 44
Show... 24
Show Data Fields 32
Sight ‘N Go 32, 33
Signal Strength 74
Size 99
Skyview 74
Specifications 99
Squelch codes 8, 97
Status Bar 4
Stopwatch 90
Stop Navigation 24, 32
Street name 58
Sun & Moon 50, 51, 53, 54, 56
114
Symbol 6, 7
T
Temperature Range 99
Text Setup 28
Thumb Stick 3
Time Page 78
Tones 14, 88
Call 14
Ring 14
Roger 14
Setup 14
Topo map 102
TracBack 71
Track
Log 70
Page 70
Points 28
Setup 28
Up 27, 76
Transferring 102
Transmit
A Location 20
Your location 18
Transportation 55
Trip Computer Page 40
Big Numbers 40
Options 40
Overview 40
Reset 40
Restore Defaults 40
Turn compass Off/On 34
Turn GPS Off/On 16
Two-way Radio iii, 1, 97
U
U. S. Waterways & Lights 102
UHF 97
Units Page 79
Unlock Buttons 3, 44
Use With GPS Off 76
V
Vibrate 14
View
Contact 23
Elevation 37
Points 36, 38
Pressure Plot 37
Track 52
Voice Operated Transmission 12
Voice Scramble 98
VOX 12
W
WAAS 75, 85
Waterproof 1, 99
Waypoint 45, 46
Create 45, 46
Delete 48
Edit 47
Move 48
Project 47
Weather Alert 15, 60
Weather Radio 15, 60
Radio Page 60
Shortcut Menu Access 60
WorldMap 102
Z
Zoom 23, 27
Ranges 36, 37
Altimeter Page 36
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin web site at www.garmin.com.
© Copyright 2003 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00284-00 Rev. A