Owner`s manual | Garmin Street Pilot 2720 GPS Receiver User Manual

StreetPilot 2720
®
owner’s manual
© Copyright 2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, U.S.A.
Tel. 913/397.8200 or 800/800.1020
Fax 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle,
Abbey Park Industrial Estate,
Romsey, SO51 9DL, U.K.
Tel. 44/0870.8501241
Fax 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or
stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a
single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision
hereto, provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any
unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in
the content without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.com) for
current updates and supplemental information concerning the use and operation of this and other Garmin products.
Garmin®, StreetPilot®, and MapSource® are registered trademarks and City Navigator™ is a trademark of Garmin Ltd. or its subsidiaries and
may not be used without the express permission of Garmin.
December 2005
Part Number 190-00475-00 Rev. B
Printed in Taiwan
PREFACE
Contact Garmin
PREFACE
If you encounter any difficulty while using your Garmin
StreetPilot® 2720, or if you have any questions, in
the U.S.A. contact Garmin Product Support by phone at
913/397.8200 or 800/800.1020, Monday–Friday,
8 AM–5 PM Central Time. You can also go to the
Garmin Web site at http://www.garmin.com/contactUs/.
Click Technical Product Support and fill out the form.
®
Serial Number
Record the serial number (8-digit number located on
the back of the unit) in case your StreetPilot 2720 needs
service or you would like to buy additional maps.
Serial Number: ___ ___ ___ ___ ___ ___ ___ ___
In Europe, contact Garmin (Europe) Ltd. at
44/0870.8501241.
Quick Links
• Finding an address: page 9
• Viewing the Map page: page 16
• Creating a new saved route: page 20
• Saving a location you have found: page 12
• Using the mileage logs: page 25
StreetPilot 2720 Owner’s Manual
• Turning off the GPS to use indoors: page 19
• Adjusting the volume: page 29
• Adjusting the brightness: page 35
• Loading the USB drivers: page 36
• Cleaning and storing your unit: page 39
i
PREFACE
Preface ................................................... i
Contact Garmin ............................................i
Warnings & Cautions ................................. iii
Getting Ready ....................................... 1
Looking at the StreetPilot 2720 .................. 1
Installing the 2720 in Your Vehicle ............. 2
Using the Remote Control ......................... 4
Using the 2720 ........................................... 5
Manual Conventions .................................. 5
Find It and Go! ...................................... 6
Finding a Restaurant ................................. 6
Following Your Route ................................. 7
Where To? ............................................. 8
Using the Where To? Menu ....................... 8
Understanding the Search Results ............ 8
Finding an Address .................................... 9
Understanding the Information Page ....... 10
Finding Recently Found Locations ......... 10
Finding Locations in a Different Area ........11
Narrowing Your Search .............................11
My Locations....................................... 12
Saving Locations ..................................... 12
Saving Your Current Location .................. 12
ii
Setting a Home Location ......................... 13
Finding Saved Locations ......................... 13
Editing Saved Locations .......................... 14
Deleting a Saved Location ....................... 15
Viewing the Map & Using the Tools .. 16
Viewing the Map Page ............................. 16
Browsing the Map .................................... 17
Trip Computer .......................................... 18
Turn List ................................................... 18
GPS Info Page ......................................... 19
Creating and Editing Routes ............. 20
Creating a New Saved Route .................. 20
Editing a Saved Route ............................. 21
Adding Multiple Destinations to a
Saved Route ......................................... 22
Saving the Active Route ........................... 23
Navigating a Saved Route ....................... 23
Recalculating the Route ........................... 23
Stopping Your Route ................................ 23
Adding a Detour to a Route ..................... 23
Adding Avoidances .................................. 24
Using the Logs.................................... 25
Adjusting the Track Log ........................... 25
Using the Mileage Logs ........................... 25
Traffic Information .............................. 26
Connecting the FM Traffic Receiver ........ 26
Avoiding Traffic ........................................ 26
Changing the Traffic Settings ................... 27
Adding an FM Traffic Subscription ........... 28
Customizing the StreetPilot 2720 .... 29
Adjusting the Volume ............................... 29
Customizing the General Settings ........... 29
Changing the Map Settings ..................... 31
Customizing the Map Data Fields ............ 33
Changing the Navigation Settings ........... 34
Adjusting the Traffic Settings ................... 35
Changing the Screen Settings ................. 35
Viewing Unit Information (About) ............. 35
Restoring the Settings ............................. 35
Appendix ............................................. 36
Loading USB Drivers ............................... 36
Updating the Software and Map Data ...... 37
Custom POIs (Points of Interest) ............. 38
Caring for Your StreetPilot 2720 .............. 39
Technical Specifications ........................... 40
2720 Troubleshooting .............................. 42
Index .................................................... 43
StreetPilot 2720 Owner’s Manual
PREFACE
Warning
This manual uses the term Warning to indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Failure to avoid the following potentially hazardous situations could
result in an accident or collision resulting in death or serious injury.
When installing the unit in a vehicle, place the unit securely so that it
does not interfere with vehicle operating controls or obstruct the driver’s
view of the road (see diagram).
Do not mount
where driver’s
field of vision is
blocked.
Do not place
unsecured on
the vehicle
dash.
Do not mount in front of an airbag field of deployment.
When navigating, carefully compare information displayed on the unit to
all available navigation sources, including information from street signs,
visual sightings, and maps. For safety, always resolve any discrepancies or
questions before continuing navigation.
Always operate the vehicle in a safe manner. Do not become distracted
by the unit while driving, and always be fully aware of all driving
conditions. Minimize the amount of time spent viewing the screen of the
unit while driving and use voice prompts when possible.
Do not enter destinations, change settings, or access any functions
requiring prolonged use of the unit’s controls while driving. Pull over in
a safe and legal manner before attempting such operations.
WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or
reproductive harm. This Notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional
information, refer to our Web site at http://www.garmin.com/prop65.
StreetPilot 2720 Owner’s Manual
iii
PREFACE
Caution
This manual uses the term Caution to indicate a potentially hazardous situation, which, if not avoided, may result in minor injury or property damage. It
may also be used without the symbol to alert you to avoid unsafe practices.
Failure to avoid the following potentially hazardous situations may
result in injury or property damage.
The unit is designed to provide you with route suggestions. It does not
reflect road closures or road conditions, traffic congestion, weather
conditions, or other factors that may affect safety or timing while
driving.
Use the unit only as a navigational aid. Do not attempt to use the unit
for any purpose requiring precise measurement of direction, distance,
location, or topography. This product should not be used to determine
ground proximity for aircraft navigation.
The Global Positioning System (GPS) is operated by the United
States government, which is solely responsible for its accuracy and
maintenance. The government’s system is subject to changes which
could affect the accuracy and performance of all GPS equipment,
including the unit. Although the unit is a precision navigation device,
any navigation device can be misused or misinterpreted and, therefore,
become unsafe.
The unit has no user-serviceable parts. If you ever have a problem with
your unit, take it to an authorized Garmin dealer for repairs.
The unit is fastened shut with screws. Any attempt to open the case to
change or modify the unit in any way voids your warranty and may
result in permanent damage to the equipment.
Important Information
MAP DATA INFORMATION: One of the goals of Garmin is to provide customers with the most complete and accurate cartography that is available to
us at a reasonable cost. We use a combination of governmental and private data sources, which we identify in product literature and copyright messages
displayed to the consumer. Virtually all data sources contain inaccurate or incomplete data to some extent. In some countries, complete and accurate map
information is either not available or is prohibitively expensive.
iv
StreetPilot 2720 Owner’s Manual
GETTING READY
GETTING READY
Looking at the StreetPilot 2720
IR window
(aim the remote here) Touch screen
➊
➋
➌
Power Switch
Weather Cap
Mini-USB
connector
Front
➊ Find—opens the Where To? menu. Press twice to
Go Home. Press and hold to open Recent Finds.
➋ Menu—opens the Main menu. Press repeatedly to
open the Main menu, Tools menu, and Settings menu.
StreetPilot 2720 Owner’s Manual
Power connector
(for 12-Volt or AC adapter)
MCX connector
(for remote
antenna)
➍
2720 Keys
Light sensor
Back
➌ Map—opens the Map page. Press repeatedly to open
the Map page, Trip Computer, and Turn List.
➍ Speak—announces status and voice directions.
1
GETTING READY
Installing the 2720 in Your Vehicle
You can use the permanent or temporary adhesive disks,
or the non-skid friction mount, to mount the StreetPilot
in your vehicle.
Permanent
adhesive disk
Temporary
adhesive disk
To attach the mounting disk to your dashboard:
1. Clean and dry the area where you want to place
the mount.
2. Remove one side of the backing from the
adhesive and place the adhesive on the bottom
of the mounting base. Remove the backing from
the bottom of the adhesive.
3. Place the mounting base so the locking lever
is facing you and then position the base on the
cleaned area. Apply pressure to adhere the base
to the dashboard.
2
NOTE: The permanent adhesive disk is extremely
difficult to remove. Only install it if you are sure
you want to leave the mount in that location.
To mount your StreetPilot 2720:
1. Align the power plug on the vehicle adapter
to the connector and slide the plug into the
connector until fully seated.
2. Slide the locking lever on the mounting base to
the left, in the unlocked position
StreetPilot 2720 Owner’s Manual
GETTING READY
3. Slide the bottom of the StreetPilot into the
mounting base until it clicks into place.
4. Slide the base’s locking lever to the right, in the
locked position.
Removing the 2720 from the Mount
1. Slide the locking lever to the left, to the unlocked
position.
2. Press the release tab down.
Release tab
Locking lever
3. Slide the 2720 out of the mounting base.
5. Plug the power adapter into an available 12-Volt
receptacle in your vehicle.
6. Route the cable so it does not interfere with
vehicle operation.
StreetPilot 2720 Owner’s Manual
3
GETTING READY
Using the Remote Control
The remote control operates using two AAA batteries. To use the remote, aim it toward the IR window on the front
left of the StreetPilot.
(Zoom) In—zooms into the map.
(Zoom) Out—zooms out of the map.
Menu—opens the Main menu. Press repeatedly
to scroll through the Main menu, the Tools
menu, and Settings menu.
Map—opens the Map page. Press repeatedly
to scroll through the Map, Trip Computer, and
Turn List.
Back—returns to the previous page and cancels
data entry.
4
Speak—announces the next turn or the GPS
status.
Thumb Stick—highlights options and moves the
map arrow. Press in to make a selection.
Page ▲ and ▼—scrolls through lists and pages.
Vol + and - —raises and lowers the volume.
Alphanumeric Keys—enters numbers and
letters. To enter letters or numbers, press the key
repeatedly until the correct character appears.
StreetPilot 2720 Owner’s Manual
GETTING READY
Using the 2720
Here a some helpful tips for using your 2720.
• Use your finger to touch the screen and select objects.
You can also press the keys on the front of the unit or
on the remote control to operate your 2720.
• Touch the Back button on any screen to return to the
previous screen.
and
to view all of the items in a list.
• Touch
• When a keyboard appears on the screen, type the
name or numbers using your finger. To enter a space,
touch . Touch
to enter numbers or special
characters. To delete the last character you entered,
touch
.
• You can look at other areas of the map by touching the
map and pulling your finger across the screen. See page
17 for more information.
• To adjust the volume, touch Volume on the Main menu.
StreetPilot 2720 Owner’s Manual
Manual Conventions
When you are instructed to “touch” something, use your
finger to touch an item on the screen. When you are
instructed to “press” something, press a key on the front
of the unit or on the remote control.
You will see small arrows (>) used in the text. They
indicate that you should touch a series of items. For
example, if you see “touch Tools > GPS Info > GPS
Settings” you should touch the Tools button, then touch
GPS Info, and then touch GPS Settings.
5
FIND IT AND GO!
FIND IT AND GO!
As soon as you turn on your Garmin StreetPilot 2720, it begins acquiring GPS satellite signals. The bars in the upperleft corner
indicate satellite strength. Touch the bars to view more information about the GPS signals.
Finding a Restaurant
➊ Touch Where To?
➋ Touch Food, Hotel….
➌ Touch Food & Drink.
➍ Touch a food category.
➎ Touch a location.
➏ Touch Go To.
6
StreetPilot 2720 Owner’s Manual
FIND IT AND GO!
Following Your Route
Follow the route to your destination using the map and the voice prompts. As you travel, your StreetPilot guides
you to your destination with voice prompts, arrows, and directions along the top of the map. If you depart from the
original route, your StreetPilot recalculates the route and provides new route instructions.
Your route is marked
with a magenta line.
Follow the arrows.
A checkered flag marks
your destination.
For more information about using the map and other tools, see pages 16–19.
Taking a Better Route
The Map page displays a yellow diamond with a road in it
in the lower-left corner when the StreetPilot has found
a better route. Touch
to take the better route. For more information about continuous auto routing, see page 34.
If you need to take a detour, press the Menu key and touch Detour. For more information about taking detours, see
page 23.
StreetPilot 2720 Owner’s Manual
7
WHERE TO?
WHERE TO?
Using the Where To? Menu
The Where To? menu
(Find menu) provides
several categories to
search for locations.
Press the Find key, or
touch Where To? on
the Main menu.
Recent Finds—find locations you have recently selected
from the search result list.
Where To? menu
Address—enter the house number and street name to
find a specific address. See page 9.
Food, Hotel…—search for locations, such as schools,
shopping centers, and hospitals.
Streets & Cities—find a city, street, intersection, or exit.
Browse Map—use the map to find the location you are
looking for, which can be helpful when you know where
the location is, but do not know the name. See page 17.
8
My Locations—save your favorite locations in My
Locations. For example, you can save the hotel where
you will be staying while on vacation. See page 12.
Understanding the Search Results
Your StreetPilot sorts the search results list by distance
from your current location; the closest locations are
listed first.
and
Touch the
to view all of the
results.
See page 11 to narrow
your search or search
in different areas.
Search Results
StreetPilot 2720 Owner’s Manual
WHERE TO?
Finding an Address
➊ From the Main menu, touch
➋ Touch a state. Touch Search
➌ Enter the address number
➍ Enter the street name and
➎ Select the street and then
➏ Select the address, if
Where To? Touch Address.
touch Done.
All Cities or select a city.
select the city.
and touch Done.
necessary. Touch Go To.
Searching for a city, street, intersection, or exit is very similar to searching for an address.
From the Main menu, touch Where To? > Streets & Cities.
StreetPilot 2720 Owner’s Manual
9
WHERE TO?
Understanding the Information Page
When you select a location from the search results list,
the location’s information page opens, as shown below.
Finding Recently Found Locations
Your StreetPilot stores the last 50 locations you have
found in Recent Finds.
➊ Touch Where To? > Recent Finds.
Touch Go To to create a route to this location.
Touch Advanced to view other options for this location:
• Insert in Current Route—add this location as the
next stop (point) in your route.
• Add As Favorite—add this location to your
Favorites. For more information, see page 12.
• Find Near Point—find a different location near this
location.
• Browse Map—view this location on the map.
10
➋ Select a location from the list.
Touch Category to display recent finds of a specific
category, such as Food, Hotel….
StreetPilot 2720 Owner’s Manual
WHERE TO?
Finding Locations in a Different Area
Narrowing Your Search
➊ From the search results list, touch Near….
➊ From the search results list, touch Spell.
➋ Select one of the search options.
➋ Enter part of the name and touch Done.
The locations near the option you selected are displayed.
Locations containing the letters you entered are displayed.
You can search for locations in a different area, such as a
different city or near your destination.
StreetPilot 2720 Owner’s Manual
To narrow your search, you can spell part of the name of
the location you are searching for.
11
MY LOCATIONS
MY LOCATIONS
Saving Locations
Saving Your Current Location
➊ Touch Advanced.
➊ Touch anywhere on the map.
➋ Touch Add As Favorite.
➋ Touch Save As Favorite.
Any time you are viewing a location’s information page,
you can save that location as a Favorite.
12
From the Main menu, touch
View Map. You can
also press the Map key on the front of the 2720.
StreetPilot 2720 Owner’s Manual
MY LOCATIONS
Setting a Home Location
➊ Touch Where To? > Go Home. ➋ Select an option.
➌ Touch Save Home.
Press the Find key twice to create a route to your Home Location. To change your Home Location, first delete it from
your Favorites (see page 15 for more information). Then set it again using the instructions above.
Finding Saved Locations
From the Main menu, touch Where To?
➊ Touch My Locations.
StreetPilot 2720 Owner’s Manual
➋ Touch Favorites.
➌ Touch a saved location.
13
MY LOCATIONS
Editing Saved Locations
From the Main menu, touch Tools > My Data > Favorites.
➊ Touch Edit/Review Favorites. ➋ Touch a location to edit.
➍ Touch an item to edit it.
➌ Touch Edit.
Name—enter a new name for the location using the on-screen keyboard.
Location—edit the physical location of the saved location; you can use
the map or enter new coordinates using the keyboard.
Elevation—enter the elevation of the saved location.
Category—assign this location to a category; touch
categories.
to view the
Symbol—select a symbol to appear on the map for this location.
14
StreetPilot 2720 Owner’s Manual
MY LOCATIONS
Deleting a Saved Location
To delete a saved location, touch Tools > My Data > Favorites.
➊ Touch Delete Favorites.
➍ Touch Delete.
➋ Touch By Selection.
➌ Touch a saved location.
Delete Options
By Selection—touch each location and delete them each individually.
By Category—select one category to delete all of the locations
assigned to that category.
Delete All—removes all saved locations from your Favorites.
StreetPilot 2720 Owner’s Manual
15
VIEWING THE MAP AND USING THE TOOLS
VIEWING THE MAP AND USING THE TOOLS
Viewing the Map Page
From the Main menu, touch View Map to open the map or press the Map key. Touch an area of the map to see
additional information, as shown below. The position icon shows your current location.
While navigating a route, touch the green
text bar to open the Turn List. See page 18.
Touch
Touch
to zoom out.
to zoom in.
Touch the Speed or Arrival
Time field to open the Trip
Computer. See page 18.
Touch the map to view and
browse a 2-D map.
Map Page while Navigating a Route
16
StreetPilot 2720 Owner’s Manual
VIEWING THE MAP AND USING THE TOOLS
Browsing the Map
From the Main menu, touch View Map. You can also
touch Where to? > Browse Map. Touch and drag
anywhere on the map to browse the map (view different
parts of the map).
➊ Touch any object on the map. Touch Review.
Tips for Browsing the Map
• Touch the map and drag to view different parts of
the map.
• Use the
and
icons to zoom in and out.
• Touch any object on the map. An arrow appears
pointing at the object you selected.
• Touch Review to open the location’s information
page; for more information, see page 10.
• Touch Save As Favorite to save the location
selected by the arrow to your Favorites.
• Touch Back to return to the previous screen.
➋ Touch Go To or Advanced.
StreetPilot 2720 Owner’s Manual
17
VIEWING THE MAP AND USING THE TOOLS
Trip Computer
Turn List
To view the Trip Computer, select the Speed or Arrival
Time field on the map. Or, from the Main menu, touch
Tools > Trip Computer.
While navigating a route, touch the green text bar on
the Map page to open the Turn List. Or, from the Main
menu, touch Tools > Turn List. The next turn on your
route is listed at the top of the list. Touch View All to see
and
to scroll
all the turns in the route. Touch
through the list.
The Trip Computer indicates your current speed and
provides statistics about your trip.
Current speed
Current
direction
of travel
Distance to your final
destination
Total
distance
traveled
(odometer)
Touch Reset Trip to reset all information on the Trip
Computer. To reset the maximum speed, touch Reset
Max.
18
The Turn List provides a list of turn-by-turn instructions
for your entire route as well as arrival information.
Direction of this turn
Distance to this turn
Turn directions
Touch a turn to see the turn on a map (the Next Turn
page). You can also, press Speak on the remote control
and
to zoom
to open the Next Turn page. Touch
in and out of the turn on the map.
StreetPilot 2720 Owner’s Manual
VIEWING THE MAP AND USING THE TOOLS
GPS Info Page
From the map or Main menu, touch the signal strength
bars in the upper-left corner of the screen to view the
GPS Info page. Or, from the Main menu, touch Tools >
GPS Info.
Sky view
Satellite signal
strength bars
The sky view shows the satellites you are receiving. The
satellite signal strength bars indicate the strength of each
satellite signal. A solid bar indicates your StreetPilot has
a strong fix on that GPS satellite, and the GPS satellite is
ready for use.
For more information about GPS, see http://www
.garmin.com/aboutGPS/.
StreetPilot 2720 Owner’s Manual
GPS Settings
From the Main menu, touch Settings > General > GPS.
You can also access the GPS Settings by touching the
GPS Settings button on the GPS Info page.
Use Indoors—touch Yes to turn the GPS receiver off
and use the unit indoors.
Set Position—if Use Indoors is enabled, you can select
a location on the map as your current location (position).
Touch OK after you select your location.
WAAS/EGNOS—disable and enable WAAS/EGNOS.
Wide Area Augmentation System (WAAS) and Euro
Geostationary Navigation Overlay Service (EGNOS)
are systems of satellites and ground stations that provide
GPS signal corrections, giving you even better position
accuracy.
To learn about WAAS and EGNOS, visit http://www
.garmin.com/aboutGPS/waas.html.
19
CREATING AND EDITING ROUTES
CREATING AND EDITING ROUTES
Creating a New Saved Route
You can store up to 50 saved routes. From the Main menu, touch Tools > My Data > Routes.
➋ Touch an option and touch
➌ Touch an option and touch
➊ Touch Create New
Next. Select the start point.
Next. Select the end point.
Saved Route.
➍ To add a stop, touch Yes, then ➎ Select your preference and
touch Next. Select the point.
20
touch Next. See page 34.
➏ Touch Finish.
StreetPilot 2720 Owner’s Manual
CREATING AND EDITING ROUTES
Editing a Saved Route
From the Main menu, touch Tools > My Data > Routes.
➊ Touch Edit/Review Routes.
➍ Touch the item to edit.
➋ Touch the route to edit.
➌ Touch Edit.
Rename—enter a new name for the route using the on-screen keyboard.
Edit/Review Points—add, arrange, remove, re-order, and review points
in the route. For more info, see the next page.
Change Preference—change the route calculation preference to Faster
Time, Shorter Distance, or Off Road. See page 34 for information about
the route preferences.
Delete Route—delete this route.
StreetPilot 2720 Owner’s Manual
21
CREATING AND EDITING ROUTES
Adding Multiple Destinations to a Saved Route
You can multiple destinations (also called via points, midpoints, or stops) to your route as you create it, as described
on page 20. You can also add points to your route when you edit the route, as described below. Follow the steps on
the previous page to begin editing the route.
➌ Touch where you to want to
Touch
Edit/Review
Points.
Touch
Add.
add the point.
➊
➋
➍ Touch an option and then
select the point.
➎ Add points as necessary.
Touch Done when finished.
Auto Arrange—arranges the points
to provide the shortest route.
Remove—touch the point you want
to remove and then touch Remove.
Re-Order—touch the point you want
to move. Touch Move Up or Move
Down. Touch Done when finished.
22
StreetPilot 2720 Owner’s Manual
CREATING AND EDITING ROUTES
Saving the Active Route
From the Main menu, touch Tools > My Data >
Routes > Save Active Route.
Navigating a Saved Route
From the Main menu, touch Tools > My Data >
Routes > Navigate Saved Route. Touch the route
you want to navigate.
Recalculating the Route
From the Main menu, touch Tools > My Data >
Routes > Recalculate Route.
Deleting All Saved Routes
Adding a Detour to a Route
If you need to take a detour from your current route,
open the Main menu and touch Detour.
1/2 mile, 2 miles, or 5 miles—select the distance of
the detour. For example if a road sign indicates that the
street is closed for the next 2 miles, touch 2 miles in the
list. Your StreetPilot recalculates your route for the next
two miles.
Detour by Road(s) In Route—select roads in your route
to avoid. For example, if the highway ramp is closed,
select the ramp in the list of roads. Your StreetPilot
recalculates your route to avoid that ramp.
From the Main menu, touch Tools > My Data >
Routes >
> Delete All Saved Routes.
Detour by Traffic Event on Route—if you are using
an FM Traffic Receiver, you can detour around traffic
events (incidents).
Stopping Your Route
Remove All Detours—touch to remove any detours you
have entered for the route.
From the Main menu, touch Stop and then touch Yes.
StreetPilot 2720 Owner’s Manual
23
CREATING AND EDITING ROUTES
Adding Avoidances
From the Main menu, touch Settings > Navigation >
to view more road types to avoid.
Creating Custom Avoids
From the Avoidance Setup menu,
touch
two times and then touch
Custom Avoids.
You can enter specific areas and roads
to avoid in your routes. When you add
a new avoid road, select the beginning
point and the end point to define the
section of the road that you want to
avoid.
> Avoidance Setup. Select the road type to avoid. Touch
➊ Touch Add New Avoid Area
or Add New Avoid Road.
➌ Touch the second corner
and touch Next.
➋ Touch the first corner
and touch Next.
➍ Touch Finish.
When you add a new avoid area, create
a rectangular area by selecting the
diagonally opposite corners.
24
StreetPilot 2720 Owner’s Manual
USING THE LOGS
USING THE LOGS
Adjusting the Track Log
As you travel, the StreetPilot creates a bread crumb trail
(track log) of your movement so you can see where you
have been. From the Main menu, touch Tools > My
Data > Track Log.
Using the Mileage Logs
You can keep four different mileage logs of your travels.
One log is always active to record your mileage. From
the Main menu, touch Tools > My Data > Mileage Log.
Touch a log to edit it.
Recording—turn off and on the track log recorder. It is
on by default.
Percentage Full—displays the current percentage
capacity of the track log. To clear the track log, touch
Percentage Full > Yes > OK.
Displaying the Track Log
From the Main menu, touch Settings > Map > Zoom
Level Detail > Track Log. Select a zoom setting at
which the track log is shown. Touch OK.
Name—enter a new name.
Your track log is now displayed as a fine dotted line on
the map.
Active—turn this log on or off.
StreetPilot 2720 Owner’s Manual
Distance—reset the mileage log.
25
TRAFFIC INFORMATION
TRAFFIC INFORMATION
Using a Garmin® FM TMC Traffic Receiver, your
StreetPilot 2720 can receive and use traffic information
broadcast over the FM radio data system. No more
changing the radio stations to hear the latest traffic
report!
When a traffic message is received, your StreetPilot
displays the incident on the map and can change your
route to avoid the traffic incident.
For more information about the FM Traffic Receiver,
visit the Garmin Web site (www.garmin.com). For
participating FM subscription providers and covered
cities, refer to http://www.garmin.com/fmtraffic.
Connecting the FM Traffic Receiver
Plug the cable from the FM Traffic Receiver into the
mini-USB connector on the back of the StreetPilot under
the weather cap.
26
Viewing Traffic Incidents
From the Main menu, touch Tools > Traffic. Touch an
item in the list to view the details. Touch Near… to view
traffic at a different location.
Traffic Symbol
Signal
strength
Color
code
Traffic Incident List
Avoiding Traffic
When a traffic incident is on your current route or on
the road you are driving, a
appears in the lower-left
corner of the map. To avoid the traffic, touch
, touch
the traffic incident, and then touch Detour Around.
StreetPilot 2720 Owner’s Manual
TRAFFIC INFORMATION
Severity Color Code
The bars to the left of the traffic symbols indicate the
severity of the traffic incident.
= Low severity; traffic is still flowing.
= Medium severity; traffic is a bit congested.
= High severity; traffic is heavily congested.
Traffic Symbols
North
American
Meaning
Road Condition
Road Construction
Congestion
Accident
Incident
Information
StreetPilot 2720 Owner’s Manual
International
Changing the Traffic Settings
From the Main menu, touch Settings > Traffic.
Subscriptions—if you have an FM Traffic Receiver
connected, touch FM Traffic Subscriptions to view
your subscriptions. Touch the subscription to display the
expiration date. See the next page for information about
adding an FM Traffic subscription.
Symbols on Map—change the symbols used to indicate
the type of traffic incident. Touch each symbol to set the
zoom scale at which each symbol appears on the map.
Severity on the Map—select the scale at which the
severity is displayed on the map.
Audio Notification—turn on or off the audio notification
that alerts you about a traffic incident.
Avoid Traffic—select Yes to avoid traffic incidents
when generating a route.
27
TRAFFIC INFORMATION
Adding an FM Traffic Subscription
Your FM Traffic Receiver came with a trial subscription, or you may be in an area with free service. You can also add
subscriptions to expand your service area. Write down your FM Traffic Receiver’s unit ID. Go to http://www.garmin
.com/fmtraffic to purchase a traffic subscription and get a 25-character traffic subscription code.
➊ Touch Settings.
➋ Touch Traffic.
➌ Touch
➎ Touch Next.
➏ Enter the code and
➐ Touch OK.
28
touch Next.
Subscriptions.
➍ Touch Add
Subscription
StreetPilot 2720 Owner’s Manual
CUSTOMIZING THE STREETPILOT 2720
CUSTOMIZING THE STREETPILOT 2720
Adjusting the Volume
From the Main menu, touch Volume. Touch the
and
to adjust the volume of the speaker. Touch Settings
to open the Audio Settings; see page 30.
Customizing the General Settings
From the Main menu, touch Settings >
Changing the GPS Settings
General.
From the Main menu, touch Settings > General > GPS.
See page 19.
StreetPilot 2720 Owner’s Manual
Changing the Language
From the Main menu, touch Settings > General >
Language.
Voice Language—change the language for all voice
prompts and messages. Touch the voice you want to
use and touch OK. To delete that voice from your
StreetPilot, touch Delete and OK.
Your StreetPilot contains two different types of voice
languages: text-to-speech and pre-recorded. Languages
noted with “TTS” are text-to-speech (TTS) voices. The
text-to-speech voices “read” and “speak” the words
that are displayed on the StreetPilot. The voices have
an extensive vocabulary, and they pronounce the street
names as you approach turns. The languages without
“TTS” are pre-recorded voices, which have a limited
vocabulary and do not speak names of locations or
streets.
29
CUSTOMIZING THE STREETPILOT 2720
NOTE: If you change the Voice Language, your
StreetPilot must restart to complete this change.
Text Language—change the on-screen text to the
selected language. Changing the Text Language does not
change the language of map data or user-entered data.
Speech Rate—select the rate for the vocal prompts.
Customizing the Audio Settings
From the Main menu, touch Settings > General >
Audio.
Attention Tone—turn on or off the attention tone that
sounds before voice prompts.
Touch Screen Tone—turn on or off the tone that sounds
each time you touch the screen.
Keypress Tone—turn on or off the tone that sounds each
time you press a key on the remote.
Speed Adjusted Volume—select how much the volume
increases as your speed increases. Low increases your
volume slightly; High increases your volume the most.
This is helpful when you are driving on the highway and
the ambient noise level increases (from wind or other
factors).
Customizing Proximity Alerts
Guidance—turn on the vocal guidance prompts or select
Speak Key Only to provide vocal guidance prompts
only when the Speak key is pressed.
30
From the Main menu, touch Settings > General >
Proximity Alerts. This adjusts the visual and audio
notifications for custom POIs you have loaded on the
StreetPilot. See page 38 for more information.
StreetPilot 2720 Owner’s Manual
CUSTOMIZING THE STREETPILOT 2720
Changing Your Time Settings
From the Main menu, touch Settings > General > Time.
Time Zone—select your time zone or a nearby city.
Touch Custom to set the time manually. Touch OK after
you adjust the time. Touch List Time Zones to return to
the time zone/city list.
Time Format—select 12 or 24-hour time format.
Daylight Saving—select Auto, Yes, or No. The Auto
setting automatically adjusts the time for daylight saving
time based on your time zone.
Selecting Units
Turning Safe Mode Off and On
From the Main menu, touch Settings > General > Safe
Mode. Turn on or off the Safe Mode, which disables all
unit functions that require significant operator attention
and could become a distraction while driving. For
example, when Safe Mode is On, you cannot search for a
location while the vehicle is moving.
Changing the Map Settings
From the Main menu, touch Settings >
Map.
Map Detail—adjust the amount of detail shown on the
map. The map redraws slower when detail is added.
From the Main menu, touch Settings > General >
Units. Change all units of measure to Statute or
Metric. Custom allows you to select metric or statue
for a variety of units, such as distance, speed, and
temperature.
StreetPilot 2720 Owner’s Manual
31
CUSTOMIZING THE STREETPILOT 2720
Orientation—change the perspective of the map.
• 2D North Up—display the map in two dimensions
(2-D) with North at the top of the screen.
• 2D Track Up—display the map in two dimensions
(2-D) with your direction of travel at the top of the
screen.
• 3D Track Up—display the map in three dimensions
(3-D), with your direction of travel at the top of the
screen. This is the default map view.
Color Mode—select Day for a bright background.
Select Night for a black background. Select Auto to
automatically switch between the two based upon the
time of day.
Auto Zoom—disable or enable automatic zooming on
the map for optimal viewing. You can also specify a
maximum auto zoom distance.
Route Color—select the color of the route line.
32
Dim Roads—dim roads that are not on your route.
Select Never or While Routing.
Map Data Fields—adjust the size and content of the
data fields displayed on the Map page. Select None to
remove the data fields to see more of the map. Select
Wide to make the data fields larger; they take up more
room on the map. Select Thin to see more of the map
and also the information in the fields. See the next page
for more information.
Text Size—adjust the display size of text for various
items shown on the map, such as railroads and streets.
Zoom Level Detail—customize which map items appear
at various zoom levels. For each map item, you can
select Off, Auto, or a maximum zoom distance.
NOTE: More detail increases the time it takes the
map to refresh.
Detail Maps—enable and disable the detailed maps
loaded in your StreetPilot.
StreetPilot 2720 Owner’s Manual
CUSTOMIZING THE STREETPILOT 2720
Customizing the Map Data Fields
You can customize the information that appears in the data fields in the Map page. From the Main menu, touch
Settings >
Map >
> Map Data Fields.
➊ Touch
➋ Touch the data field
➌ Select the type of data
➍ Select the data field
➎ Repeat for each
➏ Touch Next to change
to select Wide
or Thin. Touch Next.
layout. Touch OK.
you want to customize.
Navigation Data Field.
to appear in this field.
Non-Navigating fields.
1/2, 2/2, 1/3?
1/2 indicates this
is your first choice
out of two choices
for the layout of
the data field. 2/2
means this is your
second choice.
Some types of data
fields allow you
three choices, but
some only provide
one option.
Navigation Data Fields are displayed on the Map page when you are following a route. Non-Navigating Data Fields
are displayed when you are simply driving while viewing the Map page.
StreetPilot 2720 Owner’s Manual
33
CUSTOMIZING THE STREETPILOT 2720
Changing the Navigation Settings
From the Main menu, touch Settings >
Navigation.
Vehicle—specify your vehicle type to optimize the route
for your vehicle type because some roads have vehiclebased restrictions.
Preference—select a preference for route calculations.
• Faster Time—routes calculated with this setting are
faster to drive but may be longer in distance.
• Shorter Distance—routes calculated with this setting
are shorter in distance but may take more time to
drive.
• Off Road—creates a direct-line route from your
current location to your destination. This may be
useful when you are travelling outside of detailed map
coverage areas, or where no roads exist.
Ask Preference—select whether the unit asks for your
preference each time it calculates a route.
34
Next Turn Pop-up—turn on or off the Next Turn pop-up
window. Auto opens the window as you near the turn.
Off-Route Recalculation—set the way the unit
responds when you are off the route. You can silence the
“off-route, recalculating” message here.
Continuous Auto Routing—turn on or off Continuous
Auto Routing, which allows the StreetPilot to
continually search for a better route to your destination.
This can be useful if a traffic accident occurs or there
are time-restricted turns on the current route. When
Auto is selected, a
is displayed on the map when the
StreetPilot has found a better route than the one you are
currently taking. Touch
to take the better route.
StreetPilot 2720 Owner’s Manual
CUSTOMIZING THE STREETPILOT 2720
Viewing Unit Information (About)
Avoidance Setup—see page 24.
Adjusting the Traffic Settings
From the Main menu, touch Settings >
About.
See page 26.
StreetPilot—view the unit’s software version, audio
version, and unit ID.
Changing the Screen Settings
Detail Maps—view the version of detailed maps loaded.
From the Main menu, touch Settings >
Screen.
Brightness—select Manual and then touch Next. Touch
the
to decrease the brightness or
to increase it.
Select Auto for automatic brightness adjustment based
upon the light sensor’s reading.
Calibrate Touch Screen—if you think the touch screen
is not responding properly, you can calibrate the screen.
Follow the on-screen instructions. Use the remote
control to access this page, if necessary.
StreetPilot 2720 Owner’s Manual
FM Traffic Receiver—if you have an FM Traffic
Receiver connected, you can view the FM Traffic
Receiver’s unit ID.
Restoring the Settings
To restore the unit to its original settings, open the Main
menu and touch Settings > Restore Defaults > Yes.
35
APPENDIX
APPENDIX
Connecting to Your Computer
To update your software and load additional maps or
Custom POIs, you need to connect your 2720 to your
computer using the USB cable provided.
NOTE: Do not connect the USB cable to your
computer until you have loaded the USB drivers
using the enclosed CD-ROM.
Step 2: Plug in the USB cable:
1. Connect the power cable.
2. Lift the bottom flap of the weather cap.
3. Plug the mini-USB connector into the connector
on the back of the 2720, under the weather cap.
4. Plug the other end of the cable into an available
USB connector on your computer.
Step 1: Load USB Drivers
Place the enclosed USB Driver CD-ROM into your
computer’s CD-ROM drive.
If the CD-ROM does not start automatically, click Start
and then Run…. Type the letter of your CD-ROM drive
followed by setup (for example D:\setup). Then press
Enter.
Follow the instructions on your computer screen.
36
StreetPilot 2720 Owner’s Manual
APPENDIX
Updating the Software and Map Data
If you register your 2720, you will receive notification of
software and map updates. To register your 2720, go to
https://www.garmin.com/registration/selectreg.jsp.
To update the 2720 software:
1. Load the USB drivers using the enclosed
CD-ROM. See the previous page.
2. Connect the AC cable to the power connector
on the back of the StreetPilot. Turn on the
StreetPilot.
3. Connect the USB cable to your 2720 and your
computer. See the previous page.
4. Go to http://www.garmin.com/products/sp2720.
Select Updates and Downloads.
5. Click Download next to the unit software.
6. Read and agree to the terms. Click Download.
7. Select Run (or Open). Your software is updated.
StreetPilot 2720 Owner’s Manual
You can also use WebUpdater to update your 2720
software. Go to http://www.garmin.com/products/
webupdater/ to learn about WebUpdater.
Check http://www.garmin.com/unlock/update.jsp to see
if an update for your map software is available.
To find out the version of the maps that are loaded on
your 2720, open the Main menu. Touch Settings >
About > Detail Maps.
To load maps to your 2720, see the MapSource Help file.
Using a Remote GPS Antenna
Use an optional external remote GPS antenna (Garmin
GA 25) when using the unit in a vehicle with a coated
windshield or an in-screen heating system, which can
block GPS signals. Connect the antenna to the MCX
connector located on the back of the unit. To purchase,
go to http://www.garmin.com/products/sp2720. Click
Accessories.
37
APPENDIX
Custom POIs (Points of Interest)
Your StreetPilot 2720 accepts custom points of interest
(POI) databases, available from various companies on
the Internet. Some custom POI databases contain alert
information for points, such as safety cameras and
school zones. Your StreetPilot can notify you when you
approach one of these points.
After downloading your POI database, use the Garmin
POI Loader to install the POIs into your unit. The POI
Loader is available at http://www.garmin.com/products/
sp2720. Select Updates and Downloads. Refer to the
POI Loader Help file for more information; press F1 to
open the Help file.
CAUTION: Garmin is not responsible for the
consequences of using a custom POI database or
the accuracy of the safety camera or other custom
POI database.
38
Finding Custom POIs
To find the Custom POIs loaded on your 2720, press the
Menu key and then touch Where To? > My Locations
> Custom POIs.
Deleting Custom POIs
To delete all of the Custom POIs, press the Menu key.
Touch Tools > My Data > Custom POIs > Delete All.
Adjusting the Custom POI Alerts
To turn on or off the proximity alerts for your Custom
POIs, press the Menu key and then touch Settings >
General > Proximity Alerts.
Audio Notifications—turn off or on the alerts that sound
as you approach a custom POI.
Visual Notification—turn off or on the pop-up alerts
that appear as you approach a custom POI.
Continuous Notification—select which alerts (which
types of POIs) you will be continually notified about.
StreetPilot 2720 Owner’s Manual
APPENDIX
Caring for Your StreetPilot 2720
The StreetPilot 2720 is constructed of high-quality
materials and does not require user maintenance other
than cleaning.
Clean the touch screen using a soft, clean, lint-free
cloth. Use water, isopropyl alcohol, or eyeglass cleaner
if needed. Apply the liquid to the cloth and then gently
wipe the touch screen.
Cleaning the Unit
Protecting Your StreetPilot 2720
Clean the unit’s outer casing using a cloth dampened
with a mild detergent solution and then wipe dry. Avoid
chemical cleaners and solvents that can damage plastic
components.
Caring for the Touch Screen
The touch screen is intended to be operated with a finger.
Never use a hard or sharp object to operate the touch
screen or damage can result. Though a PDA stylus can
also be used to operate the touch screen, never attempt
this while operating a vehicle.
StreetPilot 2720 Owner’s Manual
• Do not store the unit where prolonged exposure to
extreme temperatures can occur (such as in the trunk
of a car), as permanent damage may result.
• To avoid theft, do not leave your StreetPilot in plain
sight when you leave your vehicle.
• Do not store alkaline batteries in the remote control
for extended periods of time. To reduce the chance for
battery leakage in the battery compartment, remove
the batteries when storing the remote control for more
than six months.
39
APPENDIX
Technical Specifications
Size: 5.6” W x 3.2” H x 2.0” D (14.3 x 8.0 x 5.0 cm)
Weight: 0.93 lbs (420 g)
Unit Case: Rugged; fully gasketed; IPX7 waterproof*
Display: Sunlight-readable, 17:9 WQVGA automotive
color TFT display with touch screen and auto dimming;
454 pixels by 240 pixels,
Map Storage: Pre-programmed internal memory
Temperature: 5° to 158°F (-15° to 70°C)
Power Supply
Source: 12 VDC
Usage: 12 watts maximum @ 13.8 VDC
Fuse: AGC/3AG - 1.0 Amp
Remote Control: Two AAA alkaline batteries (not
included)
For a complete list of specifications, visit the Garmin
Web site: http://www.garmin.com/products/sp2720/spec
.html.
Contact your local waste disposal department for
information on properly disposing of the unit.
Changing the Fuse
A 3AG 1.0 Amp fast blow fuse is located at the tip of the
vehicle adapter. If you need to change the fuse, unscrew
the black, round end piece and replace the fuse.
Unscrew
* The remote control is not waterproof.
40
StreetPilot 2720 Owner’s Manual
APPENDIX
FCC Compliance
The unit complies with Part 15 of the FCC interference limits for Class B
digital devices FOR HOME OR OFFICE USE. These limits are designed
to provide more reasonable protection against harmful interference
in a residential installation, and are more stringent than “outdoor”
requirements.
Operation of this device is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, you are encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult an experienced radio/TV
technician for help.
StreetPilot 2720 Owner’s Manual
The unit does not contain any user-serviceable parts. Repairs should only
be made by an authorized Garmin service center. Unauthorized repairs
or modifications could result in permanent damage to the equipment, and
void your warranty and your authority to operated this device under Part
15 regulations.
Software License Agreement
BY USING THE STREETPILOT 2720, YOU AGREE TO BE BOUND
BY THE TERMS AND CONDITIONS OF THE FOLLOWING
SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS
AGREEMENT CAREFULLY.
Garmin grants you a limited license to use the software embedded in this
device (the “Software”) in binary executable form in the normal operation
of the product. Title, ownership rights, and intellectual property rights in
and to the Software remain with Garmin.
You acknowledge that the Software is the property of Garmin and
is protected under the United States of America copyright laws and
international copyright treaties. You further acknowledge that the
structure, organization, and code of the Software are valuable trade secrets
of Garmin and that the Software in source code form remains a valuable
trade secret of Garmin. You agree not to decompile, disassemble, modify,
reverse assemble, reverse engineer, or reduce to human readable form the
Software or any part thereof or create any derivative works based on the
Software. You agree not to export or re-export the Software to any country
in violation of the export control laws of the United States of America.
41
APPENDIX
2720 Troubleshooting
Problem/Question
The touch screen is not
responding to my taps.
Solution/Answer
Calibrate the screen. Press Menu on the remote. Use the remote to select
Settings > Display > Recalibrate. Follow the on-screen instructions.
Check that two AAA batteries are installed.
The remote control does Check the polarity of the batteries (+ and -).
not work.
Install fresh batteries.
Aim the front of the remote toward the IR port on the front of the 2720.
Turn off the StreetPilot and then turn it back on. During start up, press and
How do I clear all my
hold the Find key on the front of the 2720. Keep pressing Find until the
message “Do you really want to erase all user data?” appears. Touch Yes to
user data?
I need to reset my 2720. clear all user data.
All original settings are restored. Your recent finds are also deleted.
Tip
Be sure you load the USB drivers before you connect the USB cable. See page 36 for information.
42
StreetPilot 2720 Owner’s Manual
INDEX
INDEX
Symbols
2 Dimensional 32
3 Dimensional 32
A
adding a traffic
subscription 28
add as favorite 10
audio settings 30
audio version 35
auto arrange, route 22
avoidances 24
avoiding traffic 26
B
better route 7, 34
brightness of the
screen 35
browse the map 17
C
calibrating the screen 35
caring for your
StreetPilot 39
category for saved
locations 14
cleaning 39
clear all user data 42
color mode 32
contact Garmin i
continuous auto
routing 34
coordinates, entering for a
saved location 14
customizing the
StreetPilot 29–35
general settings 29
map data fields 33
map settings 31
navigation settings 34
restoring the
settings 35
screen settings 35
volume 29
custom avoids 24
Custom POIs 38
D
data field 16
changing 33
default settings 35
deleting
all saved routes 23
StreetPilot 2720 Owner’s Manual
route 21
saved location 15
detail maps
disable/enable 32
version of 35
detour, adding 23
driving directions 18
following your route 7
fuse 40
log mileage 25
G
E
H
map 16
browse 17
customize 31
orientation 32
update maps 37
zoom 16, 17, 18
map data fields,
changing 33
map version 35
metric units 31
midpoints in the route 22
mileage logs 25
My Locations 12–15
Go Home 13
My Favorites 13
Recent Finds 10
Editing saved
locations 14
edit points in a route 21
EGNOS 19
elevation 14
enable maps 32
erase all user data 42
expand your search 11
F
FCC compliance 41
finding locations 8–11
address 9
item on the map 10
near this location 10
recent finds 10
restaurant 6
saved locations 13
spell the name 8
general settings 29
Go Home 13
GPS info page 19
Home location 13
I
icon on the map page
yellow diamond 26
yellow diamond with
road 34
insert in current route 10
installing the
StreetPilot 2–5
items to avoid 35
L
language 29
license agreement 41
locations
editing 14
finding 8–11
saving 12
M
N
name of a saved
location 14, 21
narrowing your search 11
navigating a saved
route 23
navigation settings 34
near button 11
43
INDEX
North Up 32
O
odometer 18
Off Road route 34
original settings 35
P
position icon 16
proximity alert 38
R
re-order points in
route 22
recalculating the route 23
recently found
locations 10
remote control 4, 39
remove all detours 23
remove points from
route 22
rename
route 21
saved location 14
reset
max. speed 18
mileage log 25
trip computer 18
44
restoring the settings 35
routes 20–24
add point 10
create new route 20
detour 23
edit a saved route 21
navigate a saved
route 23
save the active
route 23
stop 23
route preference 34
change 21
select 20
screen settings 35
serial number i
set position 19
software license
agreement 41
software version 35
speaker volume 29
specifications 40
speed (speedometer) 18
spell 11
stops in the route 22
stop navigation 23
storing the unit 39
symbol for locations 14
S
T
Safe Mode 31
saved locations 12
deleting 15
editing 14
finding 13
saved routes
deleting 23
editing 21
navigating 23
saving locations.
See saved locations
saving the active route 23
technical
specifications 40
text language 30
time 31
touch screen
calibrating 35
cleaning 39
track log 25
Track Up 32
traffic 26–28
avoid 26
incidents 26
Trip Computer 18
troubleshooting 42
Turn List 18
Z
zoom 16, 17, 18
U
Unit ID
FM Traffic
Receiver 35
StreetPilot 35
USB 36
use indoors 19
V
vehicle type 34
via points 22
viewing the map 16
voice language 29
volume 29
speed-adjusted 30
W
WebUpdater 37
Where To? 8–11
Y
yellow diamond 26
yellow diamond with
road 34
StreetPilot 2720 Owner’s Manual
Limited Warranty
This Garmin product is warranted to be free from defects in materials or
workmanship for one year from the date of purchase. Within this period,
Garmin will at its sole option repair or replace any components that fail
in normal use. Such repairs or replacement will be made at no charge
to the customer for parts or labor, provided that the customer shall be
responsible for any transportation cost. This warranty does not cover
failures due to abuse, misuse, accident, or unauthorized alteration or
repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN
ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
EXPRESS OR IMPLIED OR STATUTORY, INCLUDING
ANY LIABILITY ARISING UNDER ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO
STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE,
OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN
THE PRODUCT. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you.
Garmin retains the exclusive right to repair or replace the unit or software
or offer a full refund of the purchase price at its sole discretion. SUCH
REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR
ANY BREACH OF WARRANTY.
To obtain warranty service, contact your local Garmin authorized dealer
or call Garmin Product Support for shipping instructions and an RMA
tracking number. The unit should be securely packed with the tracking
number clearly written on the outside of the package. The unit should then
be sent, freight charges prepaid, to any Garmin warranty service station.
A copy of the original sales receipt is required as the proof of purchase for
warranty repairs.
Garmin International, Inc. Tel. 913/397.8200 Fax. 913/397.8282
Garmin (Europe) Ltd. Tel. 44/0870.8501241 Fax 44/0870.8501251
Online Auction Purchases: Products sold through online auctions
are not eligible for rebates or other special offers from Garmin. Online
auction confirmations are not accepted for warranty verification. To obtain
warranty service, an original or copy of the sales receipt from the original
retailer is required. Garmin will not replace missing components from any
package purchased through an online auction.
International Purchases: A separate warranty is provided by
international distributors for units purchased outside the United States.
This warranty is provided by the local in-country distributor and this
distributor provides local service for your unit. Distributor warranties
are only valid in the area of intended distribution. Units purchased in the
United States or Canada must be returned to the Garmin service center in
the United Kingdom, the United States, Canada, or Taiwan for service.
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin Web site at www.garmin.com.
© Copyright 2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Garmin (Europe) Ltd.
Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00475-00 Rev. B
Download PDF

advertising