Specifications | Gateway FPD2200 Computer Monitor User Manual

P/NO : 3828TUO197A (0203-Rev00)
Printed in Korea
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A1
Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A2
Description of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A4
Connecting the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A6
Connection of external equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A8
On Screen Display (OSD) Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A9
On Screen Display(OSD) Selection and Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .A10
Video Memory Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A16
i
Introduction
The FPD2200 Flat Panel Monitor has an active matrix TFT (Thin-Film
Transistor) LCD (Liquid Crystal Display).
Features
The FPD2200 is a 22-inch (55.8cm viewable) intelligent micro-processor based
monitor.
This monitor can be connected to a VCR or DVD. The monitor has two signal
connectors (D-sub and DVI-D) so that it can support both an existing analog
input (D-sub) and an advanced standard digital input (DVI-D). Two computers
can be simultaneously used while connected to this monitor.
This monitor has a picture-in-picture function so that you can watch from
VCR/DVD while using a computer.
The aspect ratio of the monitor is 16:10 so that you can feel as if you are
watching a film in a theater. You can also simultaneously display two pages of a
document set to an A4 size on the monitor, so that working efficiency can be
improved.
Digitally controlled auto-scanning is done with the micro-processor for horizontal
scan frequencies between 30 and 70kHz, and vertical scan frequencies
between 56 - 61Hz.
We accomplished to adapt the advanced design and technology to the monitor.
Soft touch buttons on the front panel are simple and allow you to conveniently
adjust a variety of image controls.
This monitor has DDC 2B function.
A1
Important Precautions
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
Do not try to roll a stand with small casters across thresholds or deep pile
carpets.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
A3
Description of Controls
Front Panel Controls
SET Button
MENU Button
SOURCE
MENU
SOURCE Selection
Button
DOWN/UP
DOWN/UP (
Buttons
LEFT/RIGHT
) LEFT/RIGHT (
Buttons
Control
SOURCE
Power Button
SET
)
Power Indicator
Function
SOURCE Selection Use this button to select an input signal.
Button
SOURCE
DOWN/UP
SET
INPUT SELECT
• DVI DIGITAL : DVI digital signal
• DSUB ANALOG : 15-pin D-sub analog signal
• V1(AV): Composite video
• V2(S): S video
DVI DIGITAL
DSUB ANALOG
V1 (AV)
V2 (S)
MENU
DOWN/UP
LEFT/RIGHT
SET
MENU Button
DOWN/UP (
Buttons
LEFT/RIGHT (
Buttons
Use this button to enter or exit the On Screen Display.
)
Use these buttons to choose or adjust items in the
On Screen Display.
) Use these buttons to choose or adjust items in the
On Screen Display.
SET Button
Use this button to enter a selection in the On
Screen Display.
Power Indicator
This indicator lights up green when the monitor
operates normally. If the monitor is in DPM (Energy
Saving) mode (stand-by/ suspend/power off), this
indicator color changes to amber.
Power Button
Use this button to turn the monitor on or off.
A4
Description of Controls
Rear Panel Controls
Connected to another object
(stand type and wall-mounted
type – optional)
DC15V
D
S-Video
Video Sound
IN L
R
PC Audio Audio
IN
L
R
Locking slot
connected to a locking cable that
can be purchased separately at
most computer stores.
DC Power Connector
DC15V
D-sub Connector
Composite Video
Input Jack
S-Video
D
DVI-D Connector
Video
IN
S-Video Input Jack
A5
Connecting the Monitor
To set up the monitor, ensure that the power is turned off to the monitor,
computer system, and other attached devices. Connect the cables to the
monitor with it lying on a cushion or a cloth.
Follow these steps:
Using the Computer
1. Connect the signal cable.
When connecting the DVI-D signal cable
.....Figure 1
Connect one end of the monitor signal cable to the input connector on the rear
panel of the monitor. 1 Connect the other end to the DVI-D connector on the
rear panel of the computer and tighten the screws. 2 Be sure the signal cable
aligns with the DVI-D connector.
When connecting the D-Sub signal cable
.....Figure 2
Connect one end of the monitor signal cable to the input connector on the rear
panel of the monitor. 1 Connect the other end to the D-Sub connector on the
rear panel of the computer and tighten the screws. 2 Be sure the signal cable
aligns with the D-Sub connector.
MAC Connect one end of the monitor signal cable to the input connector on
the rear panel of the monitor. 1 Connect the other end of the monitor signal
cable to the rear panel of Macintosh computer through a Macintosh adapter and
then tighten screws. 2'
Figure 1
DC Power
connector
DVI-D connector
DC15V
3
D
S-Video
There should be a
DVI - D port on
the computer
Video
IN
1
5
DVI-D 2
4
Power Cord
AC adapter
Signal Cable
A6
Connecting the Monitor
DC Power
connector
D-sub connector
Figure 2
DC15V
3
D
S-Video
Video
IN
1
5
D-sub 2
4
Power Cord
AC adapter
Signal Cable
MAC6
MAC Adapter
2'
Signal Cable
Note : The figure 2' shows the connection to an Apple Macintosh, using a separately
purchased adapter. For more information on adapter requirements, contact your
authorized dealer, reseller, or service provider.
2. Connect the plug from the AC adapter into the back of the monitor. 3
3. Connect one end of the AC power cord to the AC adapter 4 and the other end
to a properly grounded AC outlet that is easily accessible and close to the
monitor 5 .
A7
Connection of external equipment
Connecting the VCR/DVD
1. Connect the audio/video output jacks of the VCR/DVD to the corresponding
input ports of the set.
If you connect the S-Video input port to external equipment, you can enjoy
high definition display.
• Monitor
RCA cable (optional)
S-Video
Video
IN
Y
• VCR/DVD
Y
S-VIDEO
OUT
S-Video cable (optional)
VIDEO
OUT
2. Select an input signal.
SOURCE
DOWN/UP
INPUT SELECT
SET
Press the SOURCE button on the front panel of the
monitor to select an input.
V1(AV): Composite video,
V2(S): S-video
DVI DIGITAL
DSUB ANALOG
V1 (AV)
V2 (S)
A8
On Screen Display (OSD) Control Adjustment
Making adjustments to the image size, position and operating parameters of
the monitor are quick and easy with the On Screen Display Control system.
A quick example is given below to familiarize you with the use of the controls.
Following section is an outline of the available adjustments and selections you
can make using the OSD.
NOTE
Allow the monitor to stabilize for at least 30 minutes before making image adjustment.
To make adjustments in the On Screen Display, follow these steps:
MENU
MENU
1
1
1
2
2
3
3
4
4
4
5
5
5
6
6
6
7
7
7
DOWN/UP
SET
LEFT/RIGHT
SET
DOWN/UP
Press the MENU Button, the main menu of the OSD will appear.
To access a control, use the DOWN/UP (
) Buttons. When the desired
control icon is highlighted, press the SET Button.
Press the DOWN/UP (
) Buttons to select the desired item.
Use the LEFT/RIGHT (
) Buttons to adjust the item to the desired level.
Accept the changes by pressing the SET Button.
Exit the OSD by Pressing the MENU Button.
A9
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selection and adjusting an item
using the OSD system.
Listed below are the icons, icon names, and icon descriptions of the items that
are shown on the Menu.
Adjusting the Screen when Using a Computer
Note : When input is set as a digital signal, only the BRIGHTNESS, SETUP, and
PIP items can be adjusted. You do not need to adjust the other items.
OSD Adjust
Description
Brightness
CONTRAST/BRIGHTNESS
Image
Used to adjust the brightness of the
screen.
RGB
Color
Position
Contrast
Tracking
Setup
BRIGHTNESS
100
CONTRAST
100
Adjust the display to the contrast
desired.
PIP
RGB
USER
COLOR ADJUSTMENT
Image
USER
9300K
RED / GREEN / BLUE
To set your own color levels.
6500K
Color
Position
Tracking
RED
50
GREEN
50
BLUE
60
To appear the displays color
temperature.
• 9300K:Slightly bluish white.
• 6500K:Slightly reddish white.
9300K
6500K
Setup
PIP
Image
Horizontal Position
IMAGE POSITION
To move picture image left and right.
RGB
Color
Position
Vertical Position
Tracking
Setup
To move image up and down.
HORIZONTAL 50
VERTICAL
50
PIP
A10
On Screen Display(OSD) Selection and Adjustment
OSD Adjust
AUTO
This function is suitable for analog
signal input only. This button is for the
automatic adjustment of the screen
position, clock and phase.
CLOCK
To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.
PHASE
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
Phase adjustment should be done
after adjusting the Clock.
TRACKING
Image
RGB
Description
AUTO
OFF
Color
Position
CLOCK
50
PHASE
50
Tracking
Setup
PIP
RGB
Color
LANGUAGE To choose the language in which the
control names are displayed.
SETUP
Image
LANGUAGE
ENGLISH
IMAGE SIZE
FULL
OSD POSITION
Position
50
TRANSPARENCY
Tracking
BEEP
ON
ZOOM
Setup
1024 x 768 48.3 kHz / 60Hz
ELAPSED TIME 00000H
PIP
IMAGE SIZE This function displays the image in its
original size or enlarged size so as to
fit in the full screen of the LCD panel.
OSD POSITION To adjust position of the OSD window
on the screen. Press the SET button
to display the submenu for OSD
POSITION.
Image
OSD POSITION
RGB
Color
Position
Tracking
Setup
HORIZONTAL 50
VERTICAL
50
PIP
TRANSPARENCY To adjust the transparency of the
OSD menu screen.
BEEP
To select beep on or off.
ZOOM
To adjust horizontal and vertical
image size simultaneously.
If you want to move the zooming
point, use the H/V POSITION function
in the sub-menu. However, if the
monitor turns off when zooming in
and out the screen, the monitor will
be returned to original screen.
ELAPSED It show how long the monitor has
been used.
TIME
A11
On Screen Display(OSD) Selection and Adjustment
OSD Adjust
PIP
Image
RGB
PIP ON/OFF
OFF
Color
Position
PIP SOURCE
V1 ( AV )
PIP SIZE
LARGE
PIP POSITION
Tracking
PIP IMAGE
Setup
PIP
Description
This PIP (Picture-in-Picture) function allows the
image from the VCR or DVD to be displayed on a
sub-screen while you are using a computer.
PIP
ON/OFF
To select the sub-screen on/off.
PIP
To select an input signal for PIP.
SOURCE :V1 (AV) / V2 (S)
PIP SIZE
To adjust the size of the PIP screen.
:SMALL/MEDIUM/LARGE
PIP
To adjust the position of PIP screen.
POSITION Press the SET button to display the
submenu for PIP POSITION.
PIP POSITION
Image
RGB
Color
Position
Tracking
Setup
HORIZONTAL 50
VERTICAL
50
PIP
PIP
IMAGE
To adjust the image of the PIP screen;
Press the SET button to display the
submenu for PIP IMAGE.
Use the LEFT/RIGHT (
) buttons to
adjust the item to the desired level.
PIP IMAGE
Image
RGB
PIP CONTRAST
53
PIP BRIGHTNESS
70
PIP SHARPNESS
50
PIP COLOR
50
PIP TINT
50
Color
Position
Tracking
Setup
PIP
PIP CONTRAST
Adjust the display to the contrast desired.
PIP BRIGHTNESS
Used to adjust the brightness of the screen.
PIP SHARPNESS
To adjust the clearness of the screen.
PIP COLOR
To adjust the color to desired level.
PIP TINT
To adjust the tint to desired level. This function is
available only in NTSC broadcasting mode.
A12
On Screen Display(OSD) Selection and Adjustment
Adjusting the Screen when Using VCR/DVD ( V1 / V2 )
OSD Adjust
Description
CONTRAST Adjust the display to the contrast
desired.
ADJUSTMENT
Adjustment
CONTRAST
53
BRIGHTNESS
70
SHARPNESS
50
COLOR
50
TINT
50
Setup
LANGUAGE
ENGLISH
IMAGE SIZE
FULL
Setup
OSD POSITION
TRANSPARENCY
BEEP
0
ON
SHARPNESS To adjust the clearness of the screen.
COLOR
To adjust the color to desired level.
TINT
To adjust the tint to desired level.
This function is available only in
NTSC broadcasting mode.
LANGUAGE To choose the language in which the
control names are displayed.
SETUP
Adjustment
BRIGHTNESS Used to adjust the brightness of the
screen.
IMAGE SIZE This function displays the image in
its original size or enlarged size so
as to fit in the full screen of the LCD
panel.
OSD POSITION To adjust position of the OSD
window on the screen. Press the
SET button to display the submenu
for OSD POSITION.
OSD POSITION
Adjustment
Setup
HORIZONTAL 50
VERTICAL
50
TRANSPARENCY To adjust the transparency of the
OSD menu screen.
BEEP
To select beep on or off.
A13
Video Memory Modes
The display modes listed below are the most commonly used modes and are
set as factory defaults. The monitor automatically recognizes most input data
modes, and displays centered images with the proper sizing.
If the screen size is inappropriately set or the display is not centered, you need
to readjust the parameters of the monitor using the OSD (on-screen display).
Display Modes (Resolution)
Display Modes (Resolution)
1
2
3
4
5
6
7
VESA
VESA
VESA
VESA
VESA
VESA
Horizontal Freq.(kHz)
31.469
35.156
37.879
48.363
60.000
63.981
64.350
640 x 480
800 x 600
800 x 600
1024 x 768
1280 x 960
1280 x 1024
1600 x 1024
A14
Vertical Freq.(Hz)
60
56
60
60
60
60
60
Troubleshooting
Check the following before calling for service.
Display Position is incorrect.
Select AUTO in the OSD menu.
If the results are unsatisfactory, adjust the image position using the position icon in
the on screen display.
On the screen background, vertical bars or stripes are visible.
Select AUTO in the OSD menu.
If the results are unsatisfactory, decrease the vertical bars or stripes using the
CLOCK icon in the on screen display.
Any horizontal noise appearing in any image or characters are not clearly
portraid.
Select AUTO in the OSD menu.
If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon
in the on screen display.
Check signal Cable message.
The signal cable is not connected, or is loose. Check and secure the connection.
OUT OF RANGE message appears.
Picture is blank.
The frequency of the signal from the video card is outside the operating range of
the monitor.
Horizontal Frequency: 30kHz-70kHz
Vertical Frequency: 56Hz-61Hz
*Use the graphics board's utility software to change the frequency setting (Refer to the
manual for graphics board).
*You can change the setup to the supported resolution using the Safe Mode (Press the F8
key during booting the system).
The power LED is illuminated amber.
The monitor is in its display power management mode.
There is no active signal coming from the PC.
The signal cable is not fastened securely.
Check the computer power and graphics adapter configuration.
The monitor doesn't enter the power saving off mode (Amber).
Computer video signal is not VESA DPMS standard. Either the PC or the video
controller card is not using the VESA DPMS power management function.
NOTE
If the power indicator(LED) light is blinking amber, may result in abnomal condition of
the monitor.
Then press a power ON/OFF button on the front panel control and call your service
technician for more information.
A15
Specifications
Display
Sync Input
Video Input
Type
22inch (55.8cm) Wide SXGA TFT LCD
Anti-Glare coating
22inch (55.8cm)
70˚ (Left/Right/Up/Down)
0.294 x 0.294mm
16.7 million color
30kHz - 70kHz (Automatic)
56Hz - 61Hz (Automatic)
Separate, TTL, Positive/Negative
Digital
15 pin D-Sub connector/DVI-D connector
Separate, RGB Analog, 0.7Vp-p/75ohm, Positive
Digital
Analog : 1600 x 1024 @ 60Hz
Digital : 1600 x 1024 @ 60Hz
Viewable Size
Viewing Angle(max.)
Pixel pitch
True color
Horizontal Freq.
Vertical Freq.
Input form
Signal input
Input Form
Resolution (max.)
Power
Consumption
Dimensions
Power Input
AC Adapter
Weight
Tilt Range
Environment
Conditions
Normal
Stand-by/Suspend
Power Off
Width
Height
Depth
DC 15V 5.0A
Input
Output
Net
10˚~30˚
Operating condition
Temperature
Humidity
Storage condition
Temperature
Humidity
≤ 80W
≤ 8W
≤ 8W
58.2 cm / 22.9 inches
46.75 cm / 18.4 inches
7.3 cm / 2.87 inches
AC 100-240V, 50 /60Hz, ~1.5A
+
DC 15V
5.33A 14.8 kg / 32.6 lbs
10˚C to 35˚C
20% to 80% non-condensing
-20˚C to 60˚C
5% to 90% non-condensing
NOTE
Information in this document is subject to change without notice.
A16
Download PDF

advertising