advertisement
GB
F
User guide p.2
Notice d’utilisation p.31
CAUTION
:THIS TELEPHONE PRODUCT IS
SPECIFICALLY DESIGNED FOR PEOPLE WITH HEARING
DIFFICULTIES AND IS PROVIDED WITH A HANDSET
EARPIECE WITH VOLUME CONTROL FOR INDIVIDUAL
REQUIREMENTS. DUE CARE MUST BE TAKEN BY ALL
USERS THAT THE HANDSET EARPIECE VOLUME
CONTROL IS SET TO THE LOWEST LEVEL ACCEPTABLE
BY EACH RESPECTIVE USER. CARE SHOULD THEREFORE
BE EXERCISED TO ENSURE THAT ANY NEW USERS ARE
FAMILIAR WITH THIS REQUIREMENT.
ATTENTION:
CE TELEPHONE PEUT ETRE DESTINE
AUX PERSONNES AYANT DES PROBLEMES D’AUDITION.
IL POSSEDE UN ECOUTEUR A VOLUME VARIABLE. A
LA PREMIERE UTILISATION, ASSUREZ VOUS QUE LE
BOUTON DE REGLAGE DU VOLUME SOIT POSITIONNE
SUR LA POSITION VOLUME MINIMUM. LES PERSONNES
MALENTENDANTES POURRONT PAR LA SUITE
AUGMENTER LE VOLUME POUR L’ADAPTER A LEUR
AUDITION.
1
GB
INDEX
DESCRIPTION
- Handset and base unit controls
GENERAL SETTINGS
- How to connect the phone and set the batteries
- Charging the batteries
- Phone range
- Clean the phone
BASE SETTINGS
- Base ringer volume
HANDSET SETTINGS
- Menu access
- Settings icons displayed on the handset
- Handset registration
- Handset deregistration
- Handset ringer volume, melody and shaker
- Earpiece volume setting and tone adjust
- Network features, Flash time, Dial pause
USING THE PHONE
- Making a call
- Answering a call
- Use the call back features
- Delete stored names and numbers
- Paging the handset
- Timer
PHONE BOOK
- About the phone book
- Phone book handset ring tone settings
- Storing a number with a name
- Dialling using the phone book
- Modify a phone book entry
- Delete a phone book entry
- Transfer numbers and names into the phone book
2
PAGE
4
10
11
11
11
11
12
12
13
9
9
8
8
16
16
17
18
18
18
19
14
14
15
15
15
15
ANSWERING MACHINE
- Answering machine programming option
- How to use the answering machine
- Answering machine remote control
ADDITIONAL HANDSETS
- General settings
- Using several handsets ( registration )
- Deregister all additional handsets from the base
- Internal calls
- Call transfer to another registered handset
- Headset- Neck loop option
ADDITIONAL BASE UNIT
- General settings
- How to add a base unit
TROUBLE SHOOTING
GUARANTEE - NORMS
20
21
23
24
24
25
25
26
26
27
27
28
30
3
DESCRIPTION
Ring/Messages light indicator
Indicateur lumineux de
Sonnerie/Messages
HANDSET DESCRIPTION
DESCRIPTION DU COMBINE
Speaker
Ecouteur
Answering machine key
Touche répondeur téléphonique
LCD display
Afficheur LCD
Function and phonebook keys
Touches de fonction et de répertoire
Pick up and hang up key
Touche de décroché et de raccroché
Amplifier switch
Interrupteur ampli
Tone adjustment
Réglage de la tonalité
Shaker switch
Interrupteur vibreur
Keypad
Clavier
Flash Key
Touche flash
Microphone
2.5mm socket
Prise jack 2.5mm
( CLA3 , CLA7 option )
Amplifier key
Touche ampli
4
Amplifier volume button adjustment
Bouton de réglage volume ampli
DESCRIPTION
HANDSET DESCRIPTION
DESCRIPTION DU COMBINE
Belt clip
Clip ceinture
Batteries cover
Couvercle de batteries
5
DESCRIPTION
BASE CONTROLS
CONTROLES SUR LA BASE
Handset cradle
Support combiné
Charging LED
Voyant de charge
Charge contacts
Contacts de charge
Page key
Touche de pagination
6
DESCRIPTION
BASE CONNECTIONS
CONNECTIONS SUR LA BASE
Ringer volume setting switch
Interrupteur de réglage sonnerie
* Power adaptor socket
* Connecteur adaptateur secteur
** Line socket
** Connecteur cordon de ligne
(*) Classified “hazardous voltage” according to EN60950 standard.
Classé “tension dangereuse” selon la norme EN60950.
(**) Classified TNV-3 according to EN60950 standard.
Classée TNT-3 selon la norme EN60950
7
GENERAL SETTINGS
1 - HOW TO CONNECT THE PHONE AND SET THE BATTERIES
1 - Plug the adaptor in the power wall socket and the power plug in
the base socket (*).
2 - Connect the line cord plug to the base socket (**).
3 - Connect the line cord to the PTT socket.
4 - Insert the batteries with the correct polarity into the batteries
compartment and replace the battery cover.
5 - Place the handset on the base unit then a short beep will be heard
and the battery symbol will flash on the display, except if the
batteries are totally empty.
NOTE:
Do not expose the base to electric equipment like TV, radio, monitors, sunlight, heat or other phones...to avoid any disturbances of your phone.
(**) Classified TNV-3 according to EN60950 standard.
(*) Classified “hazardous voltage” according to EN60950 standard
2 - CHARGING THE BATTERIES
The phone is supplied with NiMH rechargeable batteries. In standby mode, batteries are fully charged around 170 hours and talk time is around 8 hours.
The battery charge icon will flash as long as the phone is being charged and will stop when the charging process is complete. The phone has an automatic charging control to avoid excessive charging.
IMPORTANT:
Batteries must be charged during 24 hours before using the phone for the first time.
Battery charge icon:
The handset display shows when the batteries are flat and when a warning signal is heard. If the phone does not have enough power or is not completly recharged, it switches itself off automatically until it is returned to the base unit.
8
GENERAL SETTINGS
3 - PHONE RANGE
The phone radio range can work up to 300 m and radio signal can be affected by many factors like a wall, obstacles...The maximum range if there are no obstacles between the phone and the base unit is around 300 m.
If the range is restricted by walls in a house or in the office, the base unit should be in a slightly elevated position.
A warning signal (beep) will be heard when the handset is out of range, the call will be stopped if the handset does not come nearer to the base unit.
4 - CLEAN THE PHONE
Clean the phone with a soft cloth. Keep the base and handset charging contacts clean. Never use polishes or cleaning agents - they could damage the finish or the electrics inside.
Note: We advise you to place the telephone on a table cloth or similar, as
rubber feet can mark some surfaces.
Thunderstorms: unplug your phone from the telephone socket during
thunderstorms because it could damage your phone. Your guarantee does not cover thunderstorm damage.
9
BASE SETTINGS
BASE RINGER VOLUME
The base ringer volume can be adjusted by using the slider switch located on the base rear panel.
The following settings are available:
Symbol Function
Off
Low
Normal
High
For product support and help visit our website at www.geemarc.com
telephone 01707 384438 or fax 01707 372529
10
HANDSET SETTINGS
1 - MENU ACCESS
:
To activate or deactivate the menu
: To move backward in the menu
: To move forward in the menu
: To confirm a selection
2 -SETTING ICONS DISPLAYED ON THE HANDSET
1 2 3 4 5
6 7 8 9 10 11 12 13 14
1 Answering Machine programmin
2 Set ring volume and melod
3 Handset programming
4 Network, flash time and dial
pause settings
5 Earpiece volume adjust
6 Battery charge level
7 CID numbers
8 Phone book Nbr 1
9 ON/OFF line
10 Call transfer
11 Answering machine
12 Phone book Nbr 2
13 Incoming messag
14 Handset registered on the base
3 - HANDSET REGISTRATION
The handset is already registered with the base ( factory setting) , the icon
must be fixed .
If this one flashes that means the handset is not linked with the base and must be registered ( see P 24, “using several handset” )
4-HANDSET DEREGISTRATION
To deregister the handset from the base unit :
- Press key
- Press then key
- Enter the PIN code ( factory setting 1111 ), then press
The icon flashes , the handset is deregistered
11
to confirm
HANDSET SETTINGS
5 - HANDSET RINGER VOLUME, MELODY AND SHAKER
To set the volume and melody please follow instructions below:
1 - Press the key.
2 - Press the or the key to select the icon
3 - Press the key to select
4 - Now you can select one of the possibilities below:
Press the to scroll through the menu. If you want to modify entries press and keys.
1/4 ++++ for the Ringer volume.
2/4 for the Normal calls ringer melody.
3/4 for the Phone book ringer melody.
4/4 for the Phone book
5 - Press the
ringer melody.
key to confirm the settings and exit to the menu.
6 - If you want to exit to the menu press .
7- In addition to the ring, you can use the shaker function with the switch
set to the position ( on the handset right side ) .
Note : The different melodies will be active only if you have subscribed to a caller ID service
6
- EARPIECE VOLUME SETTING AND TONE ADJUST
6-1 Answering machine mode
To set the hearing volume from the earpiece to listen your messages :
- Press the key
- Press the key or to select the icon
- Press the key to confirm
1/1 : from + to ++++ ( low to high )
Select the level with or key
- Press
- Press the
to confirm
key to exit
12
HANDSET SETTINGS
6-2 Normal listening
Hearing volume can be adjusted in 4 steps on using the the handset rear, press on it successively .
This will modify the setting done for the answering machine .
button on
It also can be more amplified with the button ( on the right side ), set it on
, then press key: lit ( if not, you lose the amplification )
In both cases the button on the left side allows adjustment to the tone Hi : treble , Lo : bass , but only for the earpiece.
7 - NETWORK FEATURES, FLASH TIME, DIAL PAUSE
1 - Press the key.
2 - Press the or the key to select the icon
3 - Press the key to select
4 - You can choose from the menu below:
You can scroll into the menu by pressing the the key to modify entries, press
key. Press the or
to confirm modification.
French menu UK menu Meaning
1/3
2/3
3/3
1/5 1/2 : 1 For UK, 2 for France (CID features).
2/5 Tone/Pulse for dialling must be set to Tone.
3/5 A,B,C,D (Telephone network settings; keep A)
4/5 Flash time (R key: *** for 100ms ; ****** for 300ms
5/5 Dial pause (*) : Yes/No
Flash time : France 300ms, other countries 100ms
(*) : To insert a 3 second pause after the first digit dialed ( Yes: activated ;
NO : de-activated ), then the rest is dialed normaly. Used when plugged in at a private telephone exchange ( in an hotel, an office ...) .
5 - Press the key to exit the menu.
13
USING THE PHONE
1 - MAKING A CALL
From the keypad :
- Dial the phone number you want to call, you can press the
cancel an incorrect entry.
key to
- Press the , the number is automatically dialled.
- On completion of the call simply press the
put the handset on the base.
again to release the line or
You may first press the will be without effect .
key then dial your number but the key
From stored caller numbers :
Only if you subscrided to the “Caller ID” service
Your telephone saves the 10 last numbers of incoming calls . When the memory is full , the oldest number is replaced by the latest .
- Press the key
- Use the or key to select the wanted number ( or the name ), if you
press
- Press the
you can see also the date/time of his call .
key , the number is dialed
You may exit before dialing : press key
2 - ANSWERING A CALL
When an incoming call is received proceed by:
- Press the key to take the line and speak.
- On completion of the call simply press the again to release the line
or put the handset on the base.
Caller ID display
If you subscrided to the “Caller ID” service, the caller number or name will be displayed.
If you see ******** symbols, that means your caller doesn’t want to be identified
14
USING THE PHONE
3 - USE THE CALL BACK FEATURES
You can display the last 5 numbers you dialed
- Press the key and scroll through the list by pressing the or
keys until you select the number you want.
- Press the key to dial the number.
: Exit
: Delete the displayed entry
4 - DELETE STORED NAMES AND NUMBERS
Only if you subscrided to the “Caller ID” service, otherwise the list will be empty .
- Press the key.
- Select the desired number to delete by pressing the or key. Two
short beeps will be heard when you reach the end of the list.
- Press the key to delete the entry, a short beep will be heard .
- Do it again from step 2 for deleting other entries, otherwise exit on
pressing the key .
5 - PAGING THE HANDSET
If you wish to locate your handset on making it ring, simply follow the instructions below ( if it is in a valid receiving area )
- Press the key on the base unit located on the base front side, all
the registered handsets paged will ring.
- Press the twice on the located handset to stop the paging mode.
Pressing the key on the base unit has the same effect.
6- TIMER
A timer will be displayed on the screen after starting the call. You can check the call length by using this function.
15
PHONE BOOK
(*) You must be subscrided to the “ Caller ID” service from your local phone company to enjoy principal features of phone books.
1 - ABOUT THE PHONE BOOK
Names and phone numbers can be stored in both phone books. Each phone number stored in the phone books can be called by pressing only few buttons.
The name and the number of the caller will be displayed
(*)
during the incoming call. The caller name will be displayed if it has been stored in one of the phone books.
Each phone book may contain 10 entries.
The entries in both phone books are sorted out by using an alphabetic list.
Each name can contain up to 10 characters and each phone number can have up to 25 digits.
2 - PHONE BOOK MELODIES SETTINGS
It is possible by a different bell to identify which phone book is being used
(*)
by the setting you have done Page 12 .
Non stored numbers : Melody 2/4
Calls from numbers and names in the phone book
Calls from numbers and names in the phone book
: Melody 3/4.
: Melody 4/4
IMPORTANT :
Even if a caller is stored in a phone book, it can happen that only the normal ring tone is triggered, in this case caller may have used his or her private number function.
16
PHONE BOOK
3 - STORING A NUMBER WITH A NAME
Follow instructions below to store new entries in the phone book:
- Enter the phone number you wish to set in the phone book.
- Select one of the two phone books by pressing the or
beep will be heard and the phone book icon selected will flash.
key, a
- Enter the corresponding name and number by pressing the corresponding
number key once or twice to select the desired letter (see the table below).
8
9
0
6
7
4
5
2
3
Key Characters
1 [space] - 1
A B C 2
D E F 3
G H I 4
J K L 5
M N O 6
P Q R S 7
T U V 8
W X Y Z 9
0
* or # To confirm the key and go to another one
E xample: for AB press A*B
- Press the confirm.
key to store the entry then a beep will be heard to
Note: To leave the menu press and hold the
key.
17
PHONE BOOK
4 - DIALLING USING THE PHONE BOOK
1 - Select the desired phone book by pressing the or
.
2 - Select the desired entry in the list by using the or key .
3 - Press the key then the number will be automatically dialled.
Note: To leave the menu press the
or key.
5 - MODIFY A PHONE BOOK ENTRY
1 - Select the desired phone book by pressing the or key.
2 - Select the desired number to modify by pressing the or keys.
3 - Press the key.
4 - The number will be displayed and can be deleted by pressing the
key.
5 - Enter the new number and press the key to store.
6 - DELETE A PHONE BOOK ENTRY
1 - Select the desired phone book by pressing the or key.
2 - Select the desired number to delete by pressing the or keys.
3 - Press the key.
4 - Press the key to delete the entry.
5 - Display will show OK?
5 - Press the to confirm then a beep will be heard, otherwise press
any key 0 to 9 to cancel.
6 - If OK press key or to exit .
18
PHONE BOOK
7 - STORE NUMBERS AND NAMES INTO THE PHONE BOOK
Only available if you subscrided to the “Callaer ID” service from your local phone company, otherwise the list will be empty
1 - Press the key.
2 - Select the desired number to store in the phone book by pressing the
or keys. Two short beeps will be heard if you reach the end of the list.
3 - Select the desired phone book in which you want to store the number by
pressing the or key.
4 - Store the name as described Page 17 “ Store a number with a name .
5 - Press the to confirm the storage in the phone book.
For product support and help visit our website at www.geemarc.com
telephone 01707 384438 or fax 01707 372529
19
ANSWERING MACHINE
1 - ANSWERING MACHINE PROGRAMMING OPTIONS
To access to the menu press the key then press the
key or
use the or keys to select . To set the answering machine use the table below:
Function Programmable functions Select Default
Nbr
1/5 Modifies the system day List: 1 (Monday) to 7 1
2/5
(Sunday)
Modifies the system time Type value
(00:00 to 23:59) 00:00
3/5 Selects number of rings List: 2, 3, 4, 5, toll saver Toll
saver
4/5 Modifies remote control code Type value
(0000 to 9999) 1111
5/5 Modifies telephone answering List: ****A (top quality), A
machine recording quality ****B (standard quality)
Remote control code : confidential ID code to activate/deactivate the answering
machine or read your messasge from another phone.
Toll Saver: this option allows the machine to answer your call after 3 rings if
new messages have been received instead of 5 in case of no new messages
Answering Machine general icons displayed:
- Messages Answering Machine icon , it will be displayed when the
answering machine is on.
- Icoming message icon , it will flashes when you have a message.
20
ANSWERING MACHINE
2 - HOW TO USE THE ANSWERING MACHINE
The answering machine is activated by default. The phone can record up to 4 mins and 40 secs for top quality messages or 7 minutes for standard quality messages (see Programming options about explanation to change the telephone answering machine recording quality). When you have a new message, the light indicator will flashes.
On pressing the button ( handset rear ) you switch between earpiece and speaker mode and vice-versa .
Accessing/Exit the Answering Machine:
Press the key on the handset right side to access the machine. The number of messages, the day of the week and the time will be displayed. The telephone will state the number of messages received and play the recorded messages.
Press the key to stop
Press the key to exit
To activate or deactivate the Answering Machine follow this below:
- Press the key located on the right side of your phone.
- Press the to activate, the icon is shown
OR
- Press the key to deactivate, the icon disappears
- A tone will be heard for validation.
Record an Outgoing Message:
A standard outgoing message is factory set. You can listen this outgoing message by pressing the .
If you wish to record a new outgoing message follow instructions below:
- Press the key to enter answering machine mode.
21
ANSWERING MACHINE
- Press key and then , a tone will be heard.
- Record your outgoing messsage ( speak at 20/30cm from the microphone )
- Press the key to stop recording, a second tone will be heard, then your
outgoing message is repeated .
- Press key to exit.
Record an Incoming Message :
With this function, you can leave a local message to your family members follow instructions below:
- Press the key to enter in answering machine mode.
- Press the key and then , a tone will be heard.
- Record your outgoing message.
- Press the key to stop recording, a second tone will be heard.
- Press the key to exit
Reading messages:
-
Press the key the message reading starts.
When you press the key :
: Return to the beginning of the message reading
: Go to the next message
: Start again at the beginning
: Stop the reading
- Press the key to exit
Delete a message:
If you wish to delete a message, press the key during the message is playing, a tone will be heard to confirm.
Delete all messages:
If you wish to delete all messages after reading, press and hold the key during the answering machine announce the number of messages received,
00 will be displayed on the screen left and a tone will be heard to confirm.
22
ANSWERING MACHINE
3 - ANSWERING MACHINE REMOTE CONTROL
You can get access to your answering machine via a simple phone call.
The 4 digit remote access is factory set by default to “1111”. If you wish to change this code, see programing options page 20.
To remotely activate the answering machine
Follow instructions below:
1 - Dial your phone number.
2 - After 9 rings press the key.
3 - Enter the remote code (1111 or your new code).
4 - Press the 7 key on the phone to activate the answering machine.
To remotely deactivate the answering machine
Follow instructions below:
1 - Dial your phone number.
2 - During the outgoing message, press the key.
3 - Enter the RC code (1111 or your secret code).
4 - Press the 9 key on the phone to deactivate the answering machine .
To remotely access to the answering machine
Follow instructions below :
1- Dial your phone number.
2 - During the outgoing message, press the key.
3 - Enter the remote access code (1111 or your new code).
4 - The answering machine will announce the number of messages received
and read recorded messages. See Page 22 “ Reading messages” for keys
to use
5 - Hang up the phone when all your messages have been read.
When all messages have been read 2 tones will be heard
You may stop when you want : Hang up
23
ADDITIONAL HANDSETS
1 - GENERAL SETTINGS
With the DECT standard you have the possible settings below:
- Register up to 4 handsets to one base unit.
- Register up to 2 base units to each handset.
- Make internal call handset to handset and transfer call between handsets
registered to the same base unit.
- You can increase the phone range by using 2 base units (move between
the phone coverage areas).
The additional handset will not be equiped with the answering machine button, the function is only assigned to the main handset.
2 - USING SEVERAL HANDSETS ( Registration)
For practical applications and to make life easier, you can register several handsets to the same base unit. You will be able to answer a call anywhere at any time because all handsets will ring at the same time. You can call others registered handsets in different rooms.
You can transfer an incoming call to another handset.
How to use several handsets
All handsets you wish to use in the base unit must be registered to this base unit.To add another handset please follow instructions below for each handset:
1 - Unplug the mains adaptor from the base unit for a few seconds.
2 - Replace the adaptor to the power socket.
3 - Press the key.
4 - Press the or the key to select the icon shown on the display.
then press key.
5 - Enter the base unit PIN code (factory setting to 1111), then press
6 - The handset is now searching for the base unit to be registered.
The icon is shown fixed, the handset is ready to be used .
Note: to get the maximum efficiency and maximum range you must put the
handset near the base unit. The handset range will be the same for each handset.
24
ADDITIONAL HANDSETS
3 - DEREGISTER ALL ADDITIONAL HANDSETS FROM THE BASE
To deregister all handsets from the base unit follow the instructions below:
1 - Take one handset.
2 - Press the key.
3 - Press the and the keys to enter number 1/1 0000 will be
displayed.
4 - Enter the base unit PIN code (factory setting to 1111), then press
All additional handsets are deregistered from the base unit.
Note: handset used to deregister the additional handsets is not deregistered.
4 - INTERNAL CALLS
When you are using several handsets registered to the same base unit, you can make internal calls handset to handset. To make a call handset to handset please follow instructions below:
1 - Press the key.
2 - All other handsets will ring.
3 - Press the key to answer the call.
A tone signal will be heard during a call when you receive an external call. To answer the external call you must finish your internal call first.
25
ADDITIONAL HANDSETS
5 - CALL TRANSFER TO ANOTHER REGISTERED HANDSET
External calls can be transfered to another registered handset from the answering handset (both handsets must be registered to the same base unit).
During an incoming call:
1 - Press the key to answer the call.
2 - Press the key to transfer the call.
3 - All others handsets will ring.
4 - Press the key on the requested handsets to answer the call.
If you do not wish to come back to your call and do not wish to transfer the call to other handsets simply press the key on your called handset.
Note : You cannot transfer an external call to a handset which is not registered
to the same base station.
6 - HEADSET - NECK LOOP OPTION
If you wish you can connect a headset ref: HEADCL_BLK ( CLA3) or a neck loop Ref : CLA7 to the socket located on the bottom of the handset , with these options you can use all phone functions as described before. To answer a call simply press the release the line.
to take the line and press a second time to
26
ADDITIONAL BASE UNIT
1 - GENERAL SETTINGS
A second base unit can be connected to the network in order to extend the range of the handsets. When an other base unit is registered to a handset, it can automatically search for the next base unit if you go outside the range of the first base unit. The transfer between base units is handled automatically, although this cannot be done whilst a call is in progress. Handset will keep its connection with one of the base units until it loses connection due to having moved out of range. In this case, the handset searches for a new base unit in its registration list.
The base units coverage areas must overlap to ensure there are no gaps in the coverage. Otherwise the radio connection will be lost.
2 - HOW TO ADD A BASE UNIT
1 - Connect the additional base on the network phone socket.
2 - Plug in the adaptor.
3 - Register the handset to the base unit as described before.
Remark: The first registered handset has priority on the first base. It will be
activated when the handset will move to the second base (move to the new radio range).
To check if your handset or all handsets registered to this base are registered simply press the page button
registered to this base will ring.
on the new base, all new handsets
IMPORTANT: If you connect several bases together, the handsets registered to the additional bases will ring for a few seconds during an incoming call even if you take the line with one of the first base handsets.
27
TROUBLE SHOOTING
IF THE PHONE DOES NOT WORK
Generality:
Make sure that the phone line cord and adaptor are correctly plugged in and are not damaged.
Make sure that the batteries are fully charged.
Connect another phone on your phone socket or move your phone to another socket to check if the failure is coming from your phone or your PTT socket.
The phone does not work:
Make sure that the line cord and the power adaptor are correctly connected to the base unit or to the PTT plug and wall power socket.
Check the right polarity of the batteries.
No tone when you press
Check that the batteries are charged ( icon )
The icon must be fixed ( not flashing ), otherwise see Page 24 ( registration)
A warning tone is heard during a call:
The batteries are empty and the handset needs to be replaced in the base unit.
You are over the base unit coverage area.
No number is displayed when the phone rings:
- Please contact your phone network provider to get the caller identification service.
- When the caller does not want to show his or her number (private number), the display will show ******. However, it could be a call from a PBX and caller
ID may not work properly if the phone is connected to a PBX.
The answering machine doesn’t work or you don’t receive messages
Check that the answering machine is activated
Check that you have an outgoing message ( see P.21 “recording an outgoing message) recorded
28
TROUBLE SHOOTING
You lost some messages :
Your vocal box was full and the oldest messages have been cleaned automaticaly to allow the recording of new messages .
Clean regularly your messages off.
Re-Initialize the phone
If you have got a problem, or lose your code for instance, you may retrieve factory parameters, follow instructions :
- Remove one of the batteries
- Press key
- Put in the battery ( always pressing the key )
- Release key
- Hit the following code : # 7 3 3 7 #
Your telephone retrieved the first parameters ( from the factory )
29
GUARANTEE-
NORMS
GUARANTEE
From the moment your Geemarc product is purchased, Geemarc guarantee the product for one year. During this time, all repairs or replacements (at our option) are free of charge. Should you experience a problem then contact our helpline or visit our website at www.geemarc.com. The guarantee does not cover accidents, negligence or breakages to any parts. The product must not be tampered with or taken apart by anyone who is not an authorised Geemarc representative. The Geemarc guarantee in no way limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST
BE RETAINED AND PRODUCED IN THE EVENT OF A WARRANTY CLAIM
Please note: The guarantee applies to the United Kingdom only.
DECLARATION: Geemarc Telecom SA hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the Radio and Telecommunications Terminal Equipment Directive 1999/5/EEC and in particular article 3 section 1a, 1b and section 3. The telephone does not operate if the line current is lower than 18 mA.
Electrical connection : The apparatus is designed to operate from a 230V
50Hz supply only. (Classified as «hazardous voltage» according to EN60950 standard).
The apparatus does not incorporate an integral power on/off switch. To disconnect the power, either switch off supply at the mains power socket or unplug the AC adaptor. When installing the apparatus, ensure that the mains power socket is readily accessible.
Telephone connection : Voltages present on the telecommunication network
are classified TNV-3 (Telecommunication Network Voltage) according to the
EN60950 standard.
30
SOMMAIRE
DESCRIPTION
- Description du combiné et de la base
INSTALLATION
- Raccordements du téléphone et mise en place des batteries
- Chargement des batteries
- Rayon d’action
- Entretien du téléphone
REGLAGE DE LA BASE
- Réglage du volume de sonnerie de la base
REGLAGE DU COMBINE
- Accès au menu, déplacement
- Présentation des symboles
- Enregistrement du combiné sur la base
- Annuler l’enregistrement d’un combiné de la base
- Volume, mélodie de la sonnerie et vibreur
- Réglage du volume et de la tonalité de l’écouteur
- Propiétés du réseau, touche R (Flash), insertion d’une Pause
UTILISATION DU TELEPHONE
- Appeler
- Répondre à un appel
- Rappeler le dernier numéro composé (BIS)
- Effacer un ou plusieurs numéro du journal d’appels
- Recherche du combiné (pagination)
- Minuterie (durée des appels)
REPERTOIRE
- Description
- Mélodie affectée au répertoire
- Enregistrement d’un numéro et d’un nom
- Appeler en utilisant le répertoire
31
PAGE
4
33
33
34
34
35
40
41
41
42
42
42
43
43
44
45
36
36
36
37
37
38
39
- Modifier un numéro du répertoire
- Effacer un numéro du répertoire et son numéro
- Transfert de numéros du journal d’appels vers le répertoire
REPONDEUR TELEPHONIQUE
- Programmation du répondeur
- Utilisation du répondeur
- Activer- désactiver le répondeur à distance
- Interroger votre répondeur à distance
COMBINES ADDITIONNELS
- Généralités
- Utilisation de plusieurs combinés
- Annuler l’enregistrement de tous les combinés de la base
- Communications internes
- Transfert d’appel
- Option casque- boucle magnétique
BASE ADDITIONNELLE
- Généralités
- Ajouter une base supplémentaire
EN CAS DE PROBLEME
- Problèmes de fonctionnement
GARANTIE - NORMES
45
45
46
47
48
50
51
52
52
53
53
54
54
55
55
56
58
32
INSTALLATION
1 - RACCORDEMENT DU TELEPHONE ET MISE EN PLACE DES BATTERIES
- Branchez l’adaptateur entre la prise secteur et la prise sous la base (*) voir page 7.
- Raccordez le cordon téléphonique entre la prise France Télécom(**) et la
prise sous la base, voir page 7.
- Insérez les batteries dans le compartiment à piles du combiné en respectant
la polarité et replacez le couvercle, voir page 5.
- Placez le combiné sur la base, un bref signal retentit et l’affichage des
piles clignote sur l’écran sauf si les batteries sont totallement déchargées.
2 - CHARGEMENT DES BATTERIES
Le téléphone est livré avec des batteries NiMH rechargeables. Lorsque cellesci sont chargées au maximum, la durée de veille s’élève à 170 heures environ.
La durée maximale de communication est de 8 heures. Lorsque le téléphone est en chargement, le symbole clignote et s’arrête quand la charge est terminée. Le téléphone dispose d’un système de chargement automatique, limitant à la charge optimale .
IMPORTANT :
Les batteries doivent être chargées pendant 24 heures avant d’utiliser le téléphone pour la première fois.
Affichage du niveau de chargement de la batterie :
Le symbole s’affiche sur l’écran lorsque les batteries sont faibles et un signal d’alarme retentit. Si le téléphone n’est pas assez rechargé, il se déconnecte automatiquement jusqu’à ce qu’il soit replacé sur sa base.
Le symbole s’affiche indiquant un chargement optimal des batteries
33
INSTALLATION
3 - RAYON D’ACTION
La portée du téléphone peut atteindre 300 m en champ libre. Celle-ci peut être réduite à cause d’obstacles comme par exemple: arbres, mur, une structure métallique...
La base doit être placée à un endroit légèrement plus élevé pour obtenir des conditions optimales d’utilisation.
Un signal retentit quand le combiné est hors de portée et, la communication sera interrompue après quelques bips sauf si on se rapproche de la base.
REMARQUE :
Ne placez pas la base à proximité d’un téléviseur, d’un poste de radio, d’écrans, d’autres téléphones... afin de réduire au minimum le risque de parasites. Le soleil et les sources de chaleur sont également à
éviter.
4 - ENTRETIEN DU TELEPHONE
Nettoyez le téléphone à l’aide d’un linge doux et nettoyez régulièrement les contacts de charge situés sur la base et le combiné avec une lime à ongles par exemple. N’utilisez jamais de crèmes à polir ou de produits d’entretien car cela pourrait endommager le plastique ou les circuits électriques intérieurs.
Remarque : Les pieds en caoutchouc du téléphone pourraient endommager
certaines surfaces, placez la base sur un tissu pour eviter tout problème.
Attention : Débranchez votre téléphone par temps orageux afin d’éviter tout
dommages électriques. Ce phénomène n’est pas couvert par la garantie tout comme une chute de votre appareil.
34
REGLAGE DE LA BASE
REGLAGE DU VOLUME DE SONNERIE
Le volume de sonnerie de la base peut être réglé avec l’interrupteur situé à l’arrière de la base.
En positionnant l’interrupteur en face du symbole vous obtiendrez le niveau décrit ci-dessous :
Symbole Niveau
Coupé
Faible
Normal
Fort
TEL. SERVICE APRES VENTE :
03 28 58 75 99
Pour tout renseignement technique ou toute commande visitez notre site web sur www.geemarc.com.
Parc de l’Etoile
2, rue Galilée
59760 Grande Synthe
35
REGLAGE DU COMBINE
1 - ACCES AU MENU, DEPLACEMENT
:
Touche permettant d’accéder au menu ou de le quitter
: Touche permettant de revenir en arrière dans le menu
: Touche permettant d’avancer dans le menu
: Validation des choix
2 - PRESENTATION DES SYMBOLES
1 2 3 4 5
6 7 8 9 10 11 12 13 14
1 Programmation répondeur
2 Choix mélodie et volume
3 Programmation du combiné
4 Réglages réseaux, temps du
flash et de pause
5 Réglage du volume de l’écouteur
6 Témoin de charge de la batterie
7 Carnet des appels entrants
8 Répertoire N° 1
9 Prise de ligne
10 Transfert d’appel
11 Répondeur activé
12 Répertoire N° 2
13 Présence de message
14 Combiné enregistré sur la base
3 - ENREGISTREMENT DU COMBINE SUR LA BASE
Le combiné fourni avec la base est déjà pré-enregistré en usine. l’icône doit être fixe, signifiant la liaison avec la base.
Si celle-ci clignote cela signifie que le combiné n’est pas en liaison avec la base et doit être programmé : voir P53 “Utilisation de plusieurs combinés”
36
REGLAGE DU COMBINE
4 - ANNULER L’ENREGISTREMENT D’UN COMBINE SUR LA BASE
Pour déprogrammer un combiné de sa base procédez comme suit :
- Appuyez sir la touche
- Appuyez sur les touches et
- Entrez le code PIN de la base (1111) , validez en appuyant sur
L’icône clignote, le combiné est dévalidé de la base
4 - VOLUME, MELODIE DE LA SONNERIE ET VIBREUR
Pour régler le volume et la mélodie, veuillez effectuer la démarche suivante :
1 - Appuyez sur la touche .
2 - Appuyez sur la touche ou la touche pour sélectionner l’icône
3 - Appuyez sur la touche pour valider.
4 - Vous pouvez alors sélectionner l’une des possiblilités suivantes :
Appuyez sur la touche pour vous déplacer dans le menu. Appuyez sur les touches ou pour modifier les réglages puis appuyez sur la touche pour confirmer
1/4 Volume de la sonnerie: + faible ; ++++ forte
2/4 Mélodie de la sonnerie correspondant aux appels généraux.
3/4 Mélodie de sonnerie pour le répertoire
correspondante clignote .
(8) , l’icône
4/4 Mélodie de sonnerie pour le répertoire
correspondante clignote .
(12) l’icône
6 - Quitter le menu: appuyez sur la touche .
7- Vous pouvez activer en complément de la sonnerie la fonction vibreur en positionnant l’interrupteur situé sur le côté droit de votre téléphone sur la position .
Note : Les mélodies affectées aux répertoires ne seront actives que si vous êtes abonné au service “Présentation du numéro”
37
REGLAGE DU COMBINE
5 - REGLAGE DU VOLUME DE L’ECOUTEUR ET DE LA TONALITE
5-1 Pour le mode Répondeur
En effectuant le réglage décrit ci-dessous, vous ajusterez le volume d’écoute de vos messages ( uniquement par l’écouteur)
- Appuyez sur la touche
- Appuyez sur la touche ou la touche pour sélectionner l’icône
- Appuyez sur la touche pour valider.
1/1 : de + : faible, à ++++ : fort
Sélectionnez le niveau à l’aide des touches ou
Appuyez sur la touche pour valider
Appuyez sur la touche pour quitter
5-2 Pour la conversation
Le volume d’écoute peut être ajusté en 4 paliers, cela par appuis succésifs sur la touche située au dos du combiné.
Cela modifiera le réglage fait pour le mode répondeur .
Il peut encore être amplifié grâce au bouton situé sur le côté droit du combiné:
Placez le bouton sur et appuyez sur la touche : allumée . Si éteinte vous perdez le bénéfice de l’amplification suppléméntaire .
Lorsque la touche est allumée, le bouton situé sur le côté gauche du combiné permet le réglage des graves ( Lo) et des aigus ( Hi), mais n’agit pas sur le haut-parleur ( mode répondeur ) .
38
REGLAGE DU COMBINE
6 - PROPRIETES DU RESEAU, TOUCHE R (FLASH), INSERTION D’UNE
PAUSE
1 - Appuyez sur la touche .
2 - Appuyez sur la touche ou la touche pour sélectionner l’icône .
3 - Appuyez sur la touche pour confirmer .
4 - Dans ce menu, 3 choix sont disponibles :
Pour passer d’un réglage à un autre, appuyez sur la touche .
Appuyez sur la touche ou la touche pour modifier les réglages
Appuyez sur la touche pour confirmer.
1/3 A/B/C/D (réglages réseaux , il est conseillé de garder A).
2/3 Temps flash, réglez la touche R avec : ****** ( 300ms) ;*** ( 100ms)
En France le temps est de 300ms
3/3 Pause pour insérer une pause dans la composition du numéro
(Yes: activé/No: désactivé), cela est utile lorsque votre DECT
est relié derrière un modèle ancien de PABX ( mini-central). Après
l’envoi du 1er chiffre, une pause de 3sec est insérée avant l’envoi
du reste du numéro.
5 - Appuyez sur la touche pour quitter.
39
UTILISATION DU TELEPHONE
1 - APPELER
Depuis le clavier :
- Composez le numéro de téléphone souhaité. En cas d’erreur, appuyez sur
la touche pour corriger le chiffre précédent.
- Appuyez sur la touche , le numéro se compose automatiquement.
- Pour terminer la communication, appuyez une nouvelle fois sur la touche
ou reposez le combiné sur la base.
Vous pouvez aussi d’abord appuyer sur la touche et composer votre numéro, mais la touche sera inefficace.
Depuis le journal des appels :
Si vous êtes abonné au service “Présentation du numéro” chez votre opérateur, vous avez la possibilité de rappeler un correspondant dont le numéro est encore dans le journal des appels entrants.
Votre téléphone enregistre automatiquement les 10 derniers numéros d’appel
Quand le journal est plein, le numéro le plus ancien est remplacé par le numéro le plus récent .
Pour rappeler un correspondant depuis le journal des appels :
- Appuyez sur la touche .
- Utilisez les touches et pour sélectionner le numéro ( ou le nom si connu) .Un appui sur la touche permet de voir le numéro si le nom était affiché, un 2ème appui permet de visualiser la date et l’heure de son appel. En fin de liste 2 bip retentissent.
- Appuyez sur la touche , le numéro se compose
Pour quitter avant l’envoi : appuyez à nouveau sur la touche .
40
UTILISATION DU TELEPHONE
2 - REPONDRE A UN APPEL
Lorsque votre téléphone sonne, pour répondre :
- Appuyez sur la touche pour prendre la ligne et parler.
- En fin de communication, appuyez une nouvelle fois sur la touche ou reposez le combiné sur la base.
Affichage du nom et du numéro
Si vous êtes abonné au service “Présentation du numéro” chez votre opérateur, alors le numéro de votre correspondant s’affichera.
Deux cas peuvent encore se présenter :
1) Vous êtes aussi abonné au service “Présentation du nom”, celui-ci s’affichera en premier.
2) Vous n’êtes pas abonné au service “Présentation du nom”, mais votre correspondant est enregistré dans un des répertoires avec son nom, celui-ci apparaitra aussi.
Remarque : Si vous apercevez les symboles ******** cela signifie que
l’appelant ne désire pas être identifié.
3 - RAPPELER LE DERNIER NUMERO COMPOSE (BIS)
Vous pouvez afficher les 5 derniers numéros de téléphone que vous avez composé et les rappeler.
- Appuyez sur la touche et déplacez-vous jusqu’au numéro de
téléphone souhaité à l’aide des touches ou .
- Appuyez sur la touche et le numéro se composera automatiquement.
: Quitter la fonction
: Supprimer le numéro affiché
41
UTILISATION DU TELEPHONE
4- EFFACER UN OU PLUSIEURS NUMEROS DU JOURNAL D’APPELS
A condition d’être abonné chez votre opérateur au service “Présentation du
numéro”, sinon le journal sera vide.
- Appuyez sur la touche .
- Sélectionnez le numéro souhaité en appuyant sur la touche ou
Deux bips retentissent quand vous arrivez en fin ou début de liste.
- Utilisez la touche pour effacer l’enregistrement souhaité.
- Répétez l’opération à partir de 2- pour un autre effacement, sinon quittez
en appuyant à nouveau sur la touche .
5 - RECHERCHE DU COMBINE (PAGINATION)
Si vous avez égaré votre combiné, vous pouvez le localiser en le faisant sonner
à partir de la base ( s’il se situe dans le rayon d’action) :
- Appuyez sur la touche située sur la face avant de la base: tous les
combinés enregistrés sont appelés et sonnent.
- Appuyez deux fois sur la touche
le mode pagination.
du combiné localisé pour désactiver
Vous obtiendrez le même résultat en appuyant une fois de plus sur la touche
de la base.
6 - MINUTERIE (DUREE DES APPELS)
Peu après le début d’une conversation téléphonique, une minuterie s’affiche sur l’écran. Vous pouvez contrôler la durée de l’appel grâce à cette fonction.
Ce temps s’effacera automatiquement quelques secondes après avoir raccroché .
42
UTILISATION DU REPERTOIRE
Vous devez être abonné au service “Présentation du numéro” chez
votre opérateur, pour bénéficier des principales fonctions du répertoire
: affichage du nom, du numéro, mélodie différente
1 - DESCRIPTION
Vous pouvez enregistrer dans les 2 répertoires disponibles des noms et des numéros de téléphone.
Le nom de votre correspondant appelant s’affichera si celui-ci est mémorisé dans un des répertoires.
Chaque répertoire comporte 10 entrées maximum. Les noms sont classés par ordre alphabétique.
Chaque nom peut comporter jusqu’à 10 caractères et chaque numéro de téléphone peut comporter jusqu’à 25 chiffres.
2 - MELODIE AFFECTEE AU REPERTOIRE
Suivant le réglage que vous avez effectué ( Page 38) la mélodie pourra être différente lors d’appels de correspondants figurant dans l’un des répertoires
- Mélodie d’appels provenant de personnes enregistrées dans le premier
répertoire
- Mélodie d’appels provenant de personnes enregistrées dans le deuxième
répertoire
Pour les appels de personnes non répertoriées :
- Mélodie d’appels généraux
IMPORTANT :
Il peut arriver qu’un abonné souhaite que son appel reste anonyme ( affichage de ******* au lieu du nom). Dans ce cas, même si celui-ci est enregistré dans un répertoire, il sera impossible de le différencier par la mélodie qui lui aura
été attribuée, c’est la mélodie correspondant aux appels généraux qui sera activée.
43
UTILISATION DU REPERTOIRE
3 - ENREGISTREMENT D’UN NUMERO ET D’UN NOM
Votre téléphone dispose de 2 répertoires qui vous permettront de différencier des groupes de personnes lors de leurs appels ( mélodie différente ).
Pour enregistrer un numéro et un nom dans un des deux répertoires :
- Entrez le numéro de téléphone souhaité.
- Sélectionnez l’un des deux répertoires en appuyant sur la touche ou
.
- Entrez le nom correspondant au numéro. Appuyez sur la touche correspondant
à la lettre désirée une ou plusieurs fois jusqu’à ce que celle souhaitée apparaisse. Utilisez le tableau suivant pour vous aider.
LE NOM EST OBLIGATOIRE
6
7
4
5
2
3
Touche Lettre/symbole
1 [espace] - 1
A B C 2
D E F 3
G H I 4
J K L 5
M N O 6
P Q R S 7
8
9
T U V 8
W X Y Z 9
0 0
* ou # pour valider le caractère précédent et passer à un autre, ou attendre 2 à 3 secondes.
Exemple: pour entrer A B tapez A * B
4 - Appuyez sur la touche pour enregistrer l’entrée.
Remarque : Pour sortir du menu, appuyez et maintenez la touche
jusqu’à disparition de l’icône clignotante.
44
UTILISATION DU REPERTOIRE
4 - APPELER EN UTILISANT LE REPERTOIRE
Permet d’appeler votre correspondant à partir d’un nom et d’un numéro que vous avez enregistré dans un des répertoires.
- Sélectionnez le répertoire en appuyant sur la touche ou
- A l’aide des touches ou sélectionnez le nom dans la liste.
- Appuyez sur la touche : le numéro affecté au nom se compose.
.
Remarque : Pour quitter le répertoire avant l’envoi appuyez de nouveau sur
la touche ou .
5 - MODIFIER UN NUMERO DU REPERTOIRE
- Sélectionnez le répertoire en appuyant sur la touche ou .
- Sélectionnez le numéro à modifier en appuyant sur la touche ou .
- Appuyez sur la touche .
- Effacez le numéro en appuyant succéssivement sur la touche
pour annuler l’opération à tout moment, appuyez sur la touche
- Entrez le nouveau numéro et appuyez sur la touche
enregistrer.
pour
,
.
6 - EFFACER UN NOM DU REPERTOIRE ET SON NUMERO
- Sélectionnez le répertoire en appuyant sur la touche
- Sélectionnez le nom en appuyant sur la touche ou .
ou
- Appuyez sur la touche ( pour voir le numéro ).
- Appuyez sur la touche pour effacer l’inscription.
- OK ? : appuyez sur la touche pour valider, sinon appuyez sur
une touche de 0 à 9 pour annuler l’opération.
.
- Si OK ? validé appuyer à nouveau sur la touche
quitter
ou . pour
45
UTILISATION DU REPERTOIRE
7 - TRANSFERT DE NUMEROS DU JOURNAL D’APPELS VERS LE
REPERTOIRE
- Appuyez sur la touche .
- Sélectionnez le numéro à transférer en appuyant sur la touche ou
deux bips brefs retentissent quand vous arrivez en fin de liste.
- Sélectionnez le répertoire dans lequel vous voulez enregistrer le numéro
en appuyant sur la touche ou .
- Entrez le nom correspondant (voir tableau d’explication page 45).
- Appuyez sur la touche pour confirmer l’enregistrement.
NOTE : Même si vous êtes abonné au service “Présentation du nom”, vous devrez entrer à nouveau le nom manuellement.
TEL. SERVICE APRES VENTE :
03 28 58 75 99
Pour tout renseignement technique ou toute commande visitez notre site web sur www.geemarc.com.
Parc de l’Etoile
2, rue Galilée
59760 Grande Synthe
46
REPONDEUR TELEPHONIQUE
1 - PROGRAMMATION DU REPONDEUR
Accédez au menu en appuyant sur la touche puis sur la touche l’icône est affichée en haut à gauche Pour mettre à jour les paramètres du répondeur, utilisez le tableau suivant, appuyez sur la touche OK pour passer d’une fonction à une autre, utilisez les touches ou pour la selection :
Numéro Fonctions programmables Sélection Par
Fonction Defaut
1/5 Modification du jour Liste : 1 (Lundi) à 7 1
(Dimanche)
2/5 Modification de l’heure de 00:00 à 23:59
3/5 Sélection nombre de sonneries
00:00
Liste: 2,3,4,5, toll saver Toll
saver
4/5 Modification du code de contrôle à distance
de 0000 à 9999 1111
5/5 Modification de la qualité Liste: d’enregistrement du ****A (Qualité élevée) A répondeur ****B (Qualité standard)
Code de contrôle à distance : C’est un code confidentiel qui vous permettra
d’activer/desactiver le répondeur ou lire vos messages à partir d’un autre téléphone distant.
Toll Saver : Lorsque vous consultez votre répondeur à distance, cette fonction
permet qu’il se déclenche après 3 sonneries au lieu de 5 dans le cas ou vous avez reçu de nouveaux messages .
Présentation des icônes du répondeur:
- Icône du répondeur, elle est affichée a l’écran lorsqu’il est activé.
- Icône de message ou mémo , clignote lorsque vous avez reçu un
message .
47
REPONDEUR TELEPHONIQUE
2 - UTILISATION DU REPONDEUR
Le téléphone peut enregistrer jusqu’à 4 mins et 40 secs de messages en qualité élevée ou 7 minutes en qualité standard (voir la programmation du répondeur pour changer la qualité d’enregistrement). Lorsque vous avez un nouveau message ( non lu ), l’indicateur lumineux rouge clignote, ainsi que l’icône message.
ATTENTION : Effacez périodiquement vos messages car une fois la boite
pleine les plus anciens seront effacés pour laisser place aux nouveaux
Des appuis succésifs sur la touche située derrière le combiné feront passer du mode haut-parleur en mode écouteur et vice versa.
Note : Le contrôle de tonalité ne fonctionne qu’en mode écouteur
Accéder ou sortir du répondeur :
Appuyez sur la touche localisée sur le côté droit de votre téléphone pour accéder au répondeur. Le nombre de messages, le jour de la semaine et l’heure de réception seront affichés à l’écran. Le répondeur va prononcer le nombre de nouveaux ou anciens messages reçus et les lire.
Appuyez sur la touche pour stopper la lecture.
Appuyez sur la touche pour quitter le mode répondeur .
Activer le répondeur :
- Appuyez sur la touche
- Appuyez sur la touche
- Appuyez sur la touche
localisée sur le côté droit de votre téléphone.
, l’icône apparait .
Desactiver le répondeur :
- Appuyez sur la touche
- Appuyez sur la touche
- Appuyez sur la touche
localisée sur le côté droit de votre téléphone.
, l’icône disparait .
48
REPONDEUR TELEPHONIQUE
Enregistrer un message d’accueil :
Un message d’accueil standard est pré-enregistré en usine. Vous pouvez l’écouter en appuyant sur la touche puis sur la touche . Si vous désirez changer ( personnaliser ) ce message, procédez comme suit :
- Appuyez sur la touche ( mode répondeur )
- Appuyez sur la touche puis sur la touche , un bip sonore est émis.
- Enregistrez votre message ( max 2 minutes ) .
- Appuyez sur la touche pour stopper l’enregistrement, un second bip
est émis, votre annonnce est ensuite lue.
- Quittez le mode répondeur en appuyant à nouveau sur la touche
Enregistrer un mémo :
Cette fonction permet de laisser un message chez vous par le biais du répondeur. Pour ce faire effectuez les opérations ci-dessous :
- Appuyez sur la touche ( mode répondeur ) .
- Appuyez sur la touche puis sur la touche , un bip sonore est émis.
- Enregistrez le message que vous desirez laisser ( max 2 minutes ) .
- Appuyez sur la touche pour stopper l’enregistrement, un second bip
est émis.
- Quittez le mode répondeur en appuyant à nouveau sur la touche
Lire les messages :
- Appuyez sur la touche
s’éteindra en fin de lecture ).
, les messages sont lus ( le voyant rouge
- Appui sur la touche : Retour au début du message en cours de lecture
- Appui sur la touche : Accéder au début du message suivant
- Appui sur la touche : Retour au début du 1er message
- Appui sur la touche : Arrêt de la lecture
- Appuyez sur la touche pour quitter le mode répondeur .
49
REPONDEUR TELEPHONIQUE
Effacer un message:
Pour effacer un message, appuyez sur la touche pendant sa lecture, un bip sera émis pour confirmer l’effacement .
Effacer tous les messages:
Pour effacer tous les messages, appuyez et maintenez la touche pendant que le répondeur annonce le nombre de messages reçus, 00 sera affiché sur l’écran et un bip sonore sera émis pour confirmer.
3 - ACTIVER-DESACTIVER LE REPONDEUR A DISTANCE
Il se peut que vous ayez oublié d’activer votre répondeur avant de partir, ou alors de vouloir le désactiver. Vous pouvez accéder à votre répondeur à distance par un simple appel téléphonique.
Le code d’accès (RC code) est pré-programmé en usine par défaut à “1111”.
Pour changer ce code, reportez vous à “Programmation du répondeur” page 48
Activer le répondeur à distance:
Pour l’activer à distance à partir d’un autre poste de téléphone, procédez comme ci-dessous :
- Composez votre numéro de téléphone.
- Après 9 sonneries, appuyez sur la touche .
- Entrez le code RC (1111 ou votre nouveau code ).
- Appuyez sur la touche 7 : votre répondeur est activé .
Désactiver le répondeur à distance:
Pour désactiver votre répondeur à distance à partir d’ un autre téléphone, procédez comme ci-dessous :
- Composez votre numéro de téléphone.
- Pendant la lecture du message d’accueil, appuyez sur la touche .
- Entrez le code RC (1111 ou votre nouveau code ).
- Appuyez sur la touche 9 : votre répondeur est désactivé .
50
REPONDEUR TELEPHONIQUE
4 - INTERROGER VOTRE REPONDEUR A DISTANCE
Pour interroger à distance votre répondeur et écouter vos messages à partir d’un autre téléphone procédez comme ci-après :
- Composez votre numéro de téléphone.
- Pendant la lecture du message d’accueil, appuyez sur la touche .
- Entrez le code RC (1111 ou votre nouveau code) .
- Le répondeur annonce le nombre de messages reçus et les lit ( voir P50 : “lire
les messages” pour l’utilisation des touches de sélection des messages ).
Lorsque tous les messages ont été lus 2 “bip” retentissent .
- Pour quitter à tout moment , raccrochez le téléphone .
51
COMBINES ADDITIONNELS
1 - GENERALITES
Avec le DECT 300 vous pouvez :
- Enregistrer jusqu’à 4 combinés sur une base.
- Enregistrer un combiné sur 2 bases au maximum.
- Réaliser des communications internes et transférer des communications
externes entre combinés enregistrés sur la même base.
- Augmenter le rayon d’action en utilisant 2 bases (transfert automatique vers
la prochaine station de base).
Le modèle de combiné additionnel sera sans la fonction répondeur, celle-ci n’est opérationnelle que sur le combiné principal affecté à la base.
2 - UTILISATION DE PLUSIEURS COMBINES ( enregistrements )
L’utilisation de plusieurs combinés vous permettra de ne pas toujours vous déplacer avec le même , ceux-ci pouvant être disposés à des endroits bien précis .
Vous pourrez réaliser des appels internes ( entre combinés ), transférer un appel entrant à un autre combiné.
Tous les combinés que vous désirez utiliser doivent être enregistrés sur la base, pour chaque combiné à enregistrer procédez comme ci-dessous :
- Débranchez la base du secteur pendant quelques secondes.
- Rebranchez.
Le symbole doit clignoter
- Appuyez sur la touche .
- Appuyez sur la touche ou pour sélectionner sur l’écran l’icône
, celle-ci clignote, appuyez alors sur la touche pour confirmer
la sélection.
- Entrez le code PIN de l’unité de base (réglage usine : 1111) et appuyez sur
la touche .
- Le processus d’enregistrement est alors en cours.
Le symbole devient fixe, votre combiné est bien enregistré et utilisable .
52
COMBINES ADDITIONNELS
Remarque : Si vous utilisez plusieurs combinés sur une base, il est préférable
que celle-ci soit placée au milieu de sorte que la zone de couverture soit à peu près la même pour tous les combinés.
3 - ANNULER L’ENREGISTREMENT DES COMBINES ADDITIONNELS DE
LA BASE
L’opération décrite ci-dessous entrainera la désactivation de tous les combinés supplémentaires affectés à la base ( hormis le principal ) :
- Appuyez sur la touche .
- Utilisez les touches et
- Entrez le code PIN de l’unité de base (réglage usine : 1111) et appuyez sur
la touche .
Vous pouvez vérifier en remarquant que sur chaque combiné le symbole a disparu.
4 - COMMUNICATIONS INTERNES
Des communications internes peuvent être réalisées entre les différents combinés enregistrés sur une même base. Pour cela, procédez comme suit :
- Appuyez sur la touche
- Tous les combinés sonnent.
- Appuyez sur la touche
.
d’un des combinés pour répondre à l’appel.
Si un appel externe arrive pendant qu’une communication interne est en cours, un signal retentit. Il vous faut interrompre la communication interne pour recevoir l’appel externe.
Remarque : Vous ne pouvez pas transférer un appel externe vers un combiné
qui n’est pas enregistré sur la même base.
53
COMBINES ADDITIONNELS
5 - TRANSFERT D’APPEL
Vous pouvez transférer des appels externes d’un combiné à un autre (les deux combinés doivent être enregistrés sur la même base).
Lors d’un appel entrant :
- Appuyez sur la touche pour recevoir l’appel.
- Utilisez la touche pour transférer l’appel.
- Les autres combinés sonnent.
- Appuyez sur la touche du combiné désiré pour recevoir l’appel transféré.
Tant que celui qui a pris l’appel le premier n’appuie pas sur la touche la communication reste établie en interne, pendant ce temps l’appelant entend une mélodie d’attente .
Soit vous validez le transfert en appuyant sur la touche
(raccrochage) , soit vous reprenez la ligne en appuyant sur la touche
6 - OPTION CASQUE- BOUCLE MAGNETIQUE
Si vous le désirez, vous pouvez connecter un casque Ref: HEADCL_BLK
( CLA3) ou une boucle magnétique Ref : CLA7 sur la prise jack 2.5mm de votre téléphone localisée sous le combiné ( Voir Pg 6 description) . Avec ces accéssoires, vous pouvez utiliser les mêmes fonctions décrites dans la notice.
Pour répondre à un appel, appuyez sur la touche pour prendre la ligne et appuyez une seconde fois à la fin de la communication pour libérer la ligne.
54
BASE ADDITIONNELLE
1 - GENERALITES
Il est possible d’étendre le rayon d’action du téléphone en raccordant une base suppléméntaire au système. Lorsqu’un combiné enregistré sur plusieurs bases se trouve hors du rayon d’action de l’une d’entre elles, une recherche automatique se fera pour trouver la base la plus proche et conserver le contact téléphonique.
Le transfert d’une base à une autre se fait automatiquement mais ne fonctionne pas pendant une communication en cours.
Les zones de couverture des bases doivent se recouper afin de garantir un rayon d’action sans interruption, sinon le contact radio pourra être rompu.
2 - AJOUTER UNE BASE SUPPLEMENTAIRE
- Connectez le cordon de la base sur une deuxième prise PTT.
- Connectez l’adaptateur secteur.
- Procédez à l’enregistrement du combiné de la première base sur la seconde
base comme décrit dans le paragraphe “Utilisation de plusieurs combinés”
( P. 53) .
Remarque: le combiné de la première base reste prioritaire sur sa base
d’origine.
Le combiné deviendra actif sur la deuxième base lors du passage de la base une vers la base deux et vice versa ( changement de rayon d’action).
Pour vérifier si les combinés sont bien enregistrés à la base, appuyez simplement sur le bouton de la nouvelle base, tous les nouveaux
combinés enregistrés sur cette base sonneront dans leur rayon d’action
respectif.
IMPORTANT: Si vous connectez deux bases sur la même ligne, les combinés enregistrés sur la base additionnelle continueront de sonner pendant quelques secondes même si vous décrochez avec un combiné de la première base.
55
EN CAS DE PROBLEME
PROBLEMES DE FONCTIONNEMENT
Le téléphone ne fonctionne pas ( rien à l’écran )
Vérifiez que les batteries sont bien positionnées dans leur logement et dans le bon sens, placer le combiné sur la base ( branchée ) , le symbole doit clignoter indiquant la charge .
Pas de tonalité
- Assurez-vous que le câble du téléphone n’est pas endommagé et qu’il est
correctement enfiché, et que ce soit celui livré avec l’appareil .
- Assurez-vous que les batteries sont bien chargées ( symbole ) .
- Vérifiez que le symbole est fixe, sinon voir P.53 enregistrement des
combinés .
- Connectez un autre téléphone sur votre prise téléphonique ou branchez votre
téléphone sur une autre prise pour vérifier si la défaillance provient de votre
poste ou de votre prise “France Télécom”.
Emission d’un signal d’alarme pendant la conversation
- Les batteries sont déchargées et le combiné doit être replacé sur la base.
- Vous quittez le champ d’action de la base, s’en rapprocher .
Aucun numéro ne s’affiche lorsque le téléphone sonne
- Vous n’êtes pas abonné au service France Télécom : “Présentation du numéro”
- L’appelant ne souhaite pas être identifié ****** ( numéro masqué ) .
Le répondeur ne fonctionne pas ou vous ne recevez pas de messages
- Vérifiez que celui-ci est activé (voir P. 48 )
- Vérifiez que votre message d’accueil est bien présent ( voir P. 49)
Vous avez perdu des messages
Votre boite vocale était pleine et ensuite vous avez reçu de nouveaux messages
Les messages les plus anciens ont été effacés automatiquement pour laisser de la place.
Effacez périodiquement vos anciens messages
56
EN CAS DE PROBLEME
REINITIALISER VOTRE DECT300 AUX PARAMETRES USINE
Cela ne ré-initialise que les paramètres du combiné
Dans le cas de dysfonctionnement, ou si vous avez oubliez un code que vous avez modifié, il est possible de ré-initialiser votre téléphone. Pour se faire :
- Retirer une batterie
- Appuyer sur la touche
- Remettre la batterie ( sans relacher la touche )
- Relâcher la touche
- Entrez le code : # 7 3 3 7 #
Votre téléphone a retrouvé ses paramètres d’origine usine .
Vous percevez des parasites ou interférences pendant vos communications:
Assurez vous que la base n’est pas située près d’un appareil qui rayonne comme PC, TV, moniteurs, radio. Ecartez la de quelques mètres
57
GARANTIE - NORMES
GARANTIE
Cet appareil est garanti 1 an pièces et main-d'oeuvre. La date d'achat figurant sur le ticket de caisse fera foi. Cette garantie s'exerce sous réserve d'une utilisation normale de l'appareil. Les dommages occasionnés par les surtensions électriques, la foudre ou par un choc sur l'appareil ne peuvent en aucun cas être couverts par la garantie. En cas de problème fonctionnel et avant de nous retourner votre appareil, contactez notre service après vente de : 8h30 à
12h30 et de 14h00 à 17h00 du Lundi au Jeudi et de 8h30 à 12h30 et de 14h00
à 16h30 le Vendredi.
TEL. SERVICE APRES VENTE :
03 28 58 75 99
Parc de l’Etoile
2, rue Galilée
59760 Grande Synthe
Raccordement électrique : l’appareil est prévu pour fonctionner uniquement
avec l’adaptateur secteur 230V 50Hz fourni. (Tension classée “dangereuse” selon les critères de la norme EN60950).Par précaution en cas de danger, le bloc alimentation secteur sert de dispositif de sectionnement de l’alimentation
230V. Il doit être installé à proximité du matériel et être aisément accessible.
Raccordement téléphonique : les tensions présentes sur ce réseau sont
classées TRT-3 (Tension de Réseau de Télécommunication) au sens de la norme EN60950.
Ce produit respecte les exigences de compatibilité électro-magnétique et de sécurité électrique demandées par la directive européenne RTTE.Par ailleurs, il est compatible avec les différents réseaux téléphoniques européens (normes TBR21/37/38).Le fonctionnement de l’appareil n’est pas garanti si le courant de ligne est inférieur à 18 mA.
UGDECT300 ED03
58
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project