GE ZET1 Computer Drive User Manual

GE ZET1 Computer Drive User Manual
Installation
Instructions
30” Built-In Wall Oven
ZET1, ZET2
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
Before You Begin
• Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under warranty.
• NOTE—This appliance must be properly
grounded.
Read these instructions carefully and completely.
•
IMPORTANT—Save these
instructions for local inspector’s use.
•
IMPORTANT—Observe all
•
governing codes and ordinances.
• Note to Installer—Be sure to leave these
instructions with the consumer.
• Note to Consumer—Keep these
instructions for future reference.
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
Materials Needed
Parts Included
(4) 3/4″
Wood Screws
ATTENTION INSTALLER
(2) 5/8″
Wood Screws
Wire Nuts
Strain Relief Clamp
for 1/2” conduit
Junction
Box
36” of String
Metal Bottom
Trim Assembly
Tools Needed
1/8” Drill Bit and
Electric or Hand Drill
Phillips
Screwdriver
Adjustable Wrench
31-10633
12-05 JR
1
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F) generated
by the oven.
Rating Plate
Location
We recommend you have the electrical
wiring and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to wire
your oven according to governing codes could
result in a hazardous condition. If there are no
local codes, your oven must be wired and fused
to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70–Latest
Edition. You can get a copy by writing:
WARNING: The electrical
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
AVERTISSEMENT :
Vous devez couper l’alimentation
électrique du four avant de le
brancher. Le défaut de se conformer
à cette procédure peut entraîner des
blessures sévères et même la mort.
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a four-conductor
connection to an electric oven. When installing
an electric oven in new construction, a mobile
home, recreational vehicle or an area where
local codes prohibit grounding through the
neutral conductor, follow the instructions in
the section on NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
Electrical
Requirements
These Monogram built-in ovens require a
separate, properly grounded 3-wire 120/208 or
120/240 volt, 60 Hz power supply, protected by
a time delay fuse or circuit breaker.
• Double ovens are rated at 8.6 KW at 240 volt
and 7.8 KW at 208 volt.
• Single ovens are rated at 4.3 KW at 240 volt
and 3.9 KW at 208 volt.
2
Installation Instructions
Pre-Installation Checklist
Open oven door and remove
literature pack, broiler pan and grid,
oven racks, rack supports and a bag
with 9 hex nuts.
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLE AND DOUBLE
OVEN INSTALLATION!
Read Installation Instructions carefully
before you begin.
Be sure to place all literature, Owner’s
Manual, Installations, etc. in a safe place
for future reference.
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
Rack Supports
with Hex Nuts
Temperature
Probe
Oven Racks
EASY
INSTA
LLA
TIO
EASY
INSTALLATION
OFNYOUR NEW
Before
30"
OF
WAOVEN
30" WALL
LL OV YOUR
NEW
EN
Broiler Pan
and Grid
IMPOR you begin
-Read
IMPOR TANTSave
these
Note TANTthese
instru
to Install OBSE
instru
ctions
OWNE
RVE instructions
Before
you begin-Read
and carefully.
ctionscompletely
er- Bethese
comp
ALL
Note- R- Keep
for inspector’s
GOVE
IMPORTANTthese sure
instructions
for local
letelyuse.
ThisSave these
to leave RNINGlocal inspec and
applia
IMPORTANT- OBSERVE
ALL
GOVERNING
CODES AND ORDIANCES.
instru
carefu
CODE
these
nce
tor’s
ctions
Note to Installer- Be suremust
to leave
these
with
the consumer.
S AND
instru
use. lly.
for instructions
be
ctions
future
ORDIA
OWNER- Keep these instructionsprope
for future
reference.
with
rly grounrefere
FOR
the NCES.
Note- This
appliance must be properly grounded
(if applicable).
nce.
YOUR
consu
ded
SAFE
(if applic
mer.
Before
TY
able).
instru you begin
carefu ctions comp-Read
lly. YOUR SAFETY
ELECTRICAL REQUIREMENTS
IMPORFOR
letely these
and
ELEC
instru TANTTRICA
ctionsyouSave
Before
begin-Read
IMPOR
Before you begin-Read
these these
L REQU these
Before
TANT for local
completely and
GOVEinstructions
IREME
instructions completely
and
instru you begin
RNING - OBSE inspec
NTS
Note carefully.
tor’s
carefully.
RVE
to Install CODE Save these
carefu ctions comp-Read
use.
ALL
these IMPORTANTIMPORTANT- Save these
er- Be S AND
IMPOR lly.
letely these
instructions
localORDIA
inspector’s use.
OWNE instru
instructions for local
inspector’s use.
sure
ctions for
and
instru TANTNCES
Rto leave
IMPORTANTOBSERVE
ALL
for future
Keep
with
Save OBSERVE ALL
IMPORTANT.
the AND ORDIANCES.
IMPORctions
these CODES
these
NoteGOVERNING
refere
instru consu
TANT for localCODES AND ORDIANCES.
GOVE GOVERNING
prope ThisNote
ctions
inspec
tonce.
Installer- Be
sure mer.
to leave
applia
OBSE
Note to Installer- Be sure to leave
rly
Note RNING
tor’s
RVE
nce
these instructions
Before groun
must with the consumer. these to Install
these CODE
instructionsALL
with theuse.
consumer.
ded
S AND
be instructions
instru youOWNERKeep
these
er- Be
begin (if
applic
OWNERKeep
these instructions
OWNE instru
ctions sure ORDIANCES
-Read
able).
carefu ctionsfor
future
reference.
R- Keep
for futurewith
reference.
to leave
comp
for future
these
.
IMPOR lly. Note- This
letelyappliance
must be
the
Note-these
This appliance
must be
Noteconsu
refere
and
instru
instru TANT-properly grounded
(if applicable). prope This properly
mer.
nce. grounded
(if applicable).
Save
ctions
applia
IMPORctions for
Beforethese
you begin-Read these
nceyou begin-Read these
Before
Beforerly groun
local
must
GOVE TANT- instructions
ded
instructions
completely
and
be
OBSE inspeccompletely and
instru you begin
(if applic
Note RNING carefully.
CODE RVE ALL tor’s use.
-Read
carefully.
to
carefu ctions comp
able).
these Install
S AND
Save these
er-IMPORTANTIMPOR lly.
IMPORTANTSave these
letely these
OWNE instructionsBe sure ORDIA
andfor local inspector’s use.
instructions
for local
inspector’sinstru
use. TANT instructions
NCES
R- Keep
to leave
for future
with
. ALL IMPORctions - Save
IMPORTANTOBSERVE
the
these
IMPORTANTOBSERVE ALL
these
for local
Noterefere
instru consu
GOVERNING
CODES AND ORDIANCES.
GOVE TANTGOVERNING
inspec CODES AND ORDIANCES.
prope This appliance.
ctions mer.
OBSE
Note RNING
rly groun nceNote to Installer- Be sure to leave
tor’s Be sure to leave
RVE
Note
to InstallerCODE
to
use.
ALL
mustinstructions with the consumer.
these Install
ded these
S AND
instructions with the consumer.
er- these
(if applicbe
OWNE instructionsBeOWNEROWNER- Keep these instructions
sure ORDIA
Keep these instructions
able).
R- Keep
to leave NCES
for future
with
for future reference.
reference. .
the
thesefor future
Noteconsu
refere
Note- This appliance must be
instruThis
Noteappliance must be
prope This appliance.
ctions mer.
properly grounded (if applicable).
rly groun nce properly grounded (if applicable).
must
ded
(if applicbe
able).
Graphite
Lubricant
Literature
Pack
(Continued on following page)
3
Installation Instructions
Pre-Installation Checklist cont.
To Remove the Door (if necessary)
Place the oven on a table or platform
even with the cutout opening.
(Platform must support 175 lbs.
[79 kg] single, 350 lbs. [159 kg]
double.)
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
Open the oven door as far as it will go.
Push both hinge
locks down toward Hinge
the door frame,
Hinge
Slot
Slot
to the unlocked
position. This may
require a flat blade
screwdriver.
Remove the bottom trim from the top
of the oven. It will be installed at the
end of the installation process. The
trim is wrapped separately and taped
to the top of the unit.
Hinge
Hinge
Unlocked
Unlocked
Position
Position
Hinge
Hinge
Arm
Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Place hands on both sides of
the door, and close the oven
door to the removal position,
which is most of the way.
Removal Position
Lift door up
and out until
the hinge arms
clear the slots.
Hinge Clears Slot
NOTE: The oven door is very heavy. Be sure
you have a firm grip before lifting the oven
door off the hinges. Use caution once the
door is removed. Do not lay the door on its
handle. This could cause dents or scratches.
4
Installation Instructions
A1
Cutout for Single Built-In Oven
Cutout
Width
28 1/2” Min.
28CUTOUT
5/8” Max.
WIDTH
to
28(72.4
1/2" MIN.
2872.7
5/8" cm)
MAX.
Cabinet Width
(12.7 cm)
JUNCTION
BOX
Junction Box
LOCATION
Location
ALLOW 11/16" FOR
OVERLAP OF THE
Allow 11/16”
OVEN OVER SIDE
(1.75
for
EDGES
OFcm)
CUTOUT
overlap of oven
over side edges
of cutout
Opening
Between
THE
OPENING
Inside
Walls
BETWEEN INSIDE
Must Be
WALLS
MUST
BEAt
ATLeast
LEAST
28
281/2"WIDE
1/2”
(72.4 cm)
Wide
Cutout
TOcm)
22”22"
(55.9
CUTOUT
Height
BOTTOM
OFof
HEIGHT
to
Bottom
JUNCTION
BOX
27
1/4”
Min.
27 1/4" MIN.
Junction Box
27
275/16"
5/16”MAX.
Max.
(69.2 to 69.3 cm)
Recommended
Minimum
Cutout Location
from Floor
32 1/2” (82.6 cm)
Cutout Depth
23 1/2” (59.7 cm) Min.
Cutout Width
28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
Cutout Height
27 1/4” (69.2 cm) Min.
27 5/16” (69.2 cm) Max.
21”
21"
(53.3 cm)
ALLOW
AllowAaMINIMUM
minimum
OF 21" FOR CLEARANCE
of 21” (53.3
cm) for
TO ADJACENT
CORNERS,
clearance
to adjacent
DRAWERS,
WALLS
ETC.
WHEN THE
DOORdrawers,
IS OPENED.
corners,
walls, etc. when
door is open
Allow
1”1"(2.5
cm)
ALLOW
FOR
OVERLAPfor
minimum
ON OVENofTOP
overlap
oven
AND BOTTOM
topCUTOUT
and 11⁄4”
OF
(3.2 cm) overlap
of oven bottom
of
cutout
CABINET
WIDTH
Cabinet
30"
Width
30” (76.2 cm)
30” (76.2 cm)
5"
5”
RECOMMENDED
Recommended
CUTOUT
minimum
cutout
LOCATION
32 1/2"
location
from
FROM
THE (82.6 cm)
floor
32 1/2”
FLOOR
NOTE: If the cabinet does
not have a front frame and
the sides are less than 3/4”
(1.9 cm) thick, shim both
sides equally to establish
the cutout width.
CL
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 175 lbs. (79 kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
2"Install
x 4" ora
EQUIVALENT
solid bottom
RUNNERS
or 2” x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
SUITABLE
Runners
BRACING
TO SUPPORT
RUNNERS
21
215/8"
5/8”
OVER CENTERLINE
cm)
OF(54.9
CABINET
Over Centerline
of Cabinet
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.
This oven is not approved for
stackable or side by side installation.
5
Installation Instructions
A2
Cutout for Double Built-In Oven
Cutout
Width
28 1/2”
CUTOUT
(72.4
cm) Min.
WIDTH
28 1/2"
MIN.
28 5/8”
28 5/8"
MAX.
(72.7
cm)
Max.
Cabinet Width 30” (76.2 cm)
5”
5"
(12.7 cm)
Junction Box
JUNCTION
BOX
Location
LOCATION
ALLOW 11/16"
FOR OVERLAP
Allow
OF THE11/16”
OVEN
OVER
(1.8SIDE
cm) EDGES
for
OF CUTOUT
overlap
of oven
over side edges
of cutout
Allow a minimum
ALLOW A MINIMUM OF 21"
of 21” (53.3 cm) for
FOR CLEARANCE TO
clearance to adjacent
ADJACENT CORNERS,
corners, drawers,
DRAWERS, WALLS ETC.
walls,
etc.
when
WHEN
THE
DOOR
door is
open
IS OPENED.
Recommended
Minimum
Cutout
Location
from Floor
12” (30.5 cm)
Cutout Depth 23 1/2” (59.7 cm) Min.
Opening
Between
Inside Walls
Must Be
At Least
THE
OPENING
BETWEEN
28 1/2” INSIDE
WALLS
MUST
(72.4 cm)
BE AT LEAST
Wide
28 1/2"WIDE
Allow 1” (2.5 cm)
minimum for
overlap of oven
ALLOW
1" FOR
top and
11⁄4”
OVERLAP
(3.2
cm) overlap
ON OVEN TOP
of oven
bottom
AND
BOTTOM
cutout
OFof
CUTOUT
Cutout
Height
51 13/16”
CUTOUT
(131.6
cm) Min.
HEIGHT
51
15/16”MIN.
51 13/16"
(131.8
cm)
Max.
51
15/16"
MAX.
47”47"
(119.4
TO cm)
to Bottom
BOTTOM
OFof
JUNCTION
Junction BOX
Box
Cutout Width 28 1/2” (72.4 cm) Min.
28 5/8” (72.7 cm) Max.
Cutout Height 51 13/16” (131.6 cm) Min.
51 15/16” (131.8 cm) Max.
NOTE: If the cabinet does
not have a front frame and the
sides are less than 3/4” (1.9 cm)
thick, shim both sides equally
to establish the cutout width.
21”
21"
(52.3 cm)
30”
30"
(76.2
cm)
CABINET
Cabinet
WIDTH
Recommended
RECOMMENDED
CUTOUTcutout
LOCATION
minimum
location
12"
THE(30.5
FLOOR
from FROM
floor 12”
cm)
Width
CL
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For double
ovens, the runners and braces must
support 350 lbs. (159 kg).
Install
a
2"
x 4" or
EQUIVALENT
solid bottom
RUNNERS
or 2” x 4”
(5 cm x 10 cm)
or equivalent
runners level
with bottom
of cutout
Suitable
Bracing
to Support
UITABLE
Runners
RACING
O SUPPORT
UNNERS
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
21
5/8”
21 5/8"
OVER
CENTERLINE
(54.9
cm)
OF CABINET
Over Centerline
of Cabinet
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.
6
Installation Instructions
A3
Cutout for Single Built-In Oven
Under Counter
Gas or electric cooktops
mayGas
be or
installed
over thismay
electric cooktops
be See
installed
over this
oven.
oven.
cooktop
installation
See cooktop
instructions
forinstallation
cutout size.
instructions for cutout size.
See See
label
on top of oven for
label on top of oven for
approved
cooktop
approved
cooktopmodels.
models.
Gas and electrical connections
forGas
30"and
gaselectrical
cooktop
must be for
connections
located
in an
accessible
30” (76.2
cm)adjacent
gas cooktop
must be
locatedto
in the
an adjacent
accessible
location
right. For
a 36"
to the right. For 36” (91.4 cm)
gaslocation
cooktop
the connections
gas cooktop, the connections may be
may
be
made
to the left.
made to the left.
240V / 208V
240V / 208V
Junction
Box
Junction Box
Location
Location
25”
25"
(63.5 cm)
5”
5"
(12.7 cm)
Topand/or
and/or
side
Top
side
fillers
fillers
be
may
be may
necessary
necessary
if
if
unit is positioned
unit is positioned
between
existing
betweenBe
existing
cabinets.
sure
cabinets.
Be sure
they
are attached
securely,
they
they aresince
attached
will
anchorsince
the oven
securely
in
the will
cabinet.
they
anchor
the oven in the
cabinet.
28
1/2" MIN.
28 1/2”
28
5/8"
(72.4
cm)MAX.
Min.
28 5/8”
(72.6 cm) Max.
Allow
Allow 1”11/16"
(2.5 cm)
overlap top
of
Overlap
Top
oven
and &
of
Oven
11/16”Edges
(1.8 cm)
Side
overlap
side
of
Cutout
27 1/4"
1/4” MIN.
27
(69.2
cm) MAX.
Min.
27
5/16"
27 5/16”
(69.2 cm) Max.
22"
MIN.cm)
22” (55.9
Above
Min.
Above
Support
Support
Platform
Platform
36"
36” (91.4 cm)
Typical
Typical
Countertop
Countertop
Height
Height
edges of
cutout
24"
24”
(61 cm)
3/4"
3/4”Support
(1.9 cm)
Platform
Support
Platform
Required
Required
9/16” (14.2 cm)
55Reference
9/16"
dimension for
Reference
dimension
maximum support
height with
for
maximum
height
typical 36” (91.4support
cm) countertop
with
heighttypical 36" countertop
height
MUST
150LBS.
LBS.
MUST SUPPORT
SUPPORT 175
(78.8 KG)
This oven is not approved to be
installed under a solid disk, induction
or downdraft modular cooktop. See
the label on the top of the oven for
approved models.
7
Cabinetry
A4 Single Oven Cutout
A5
for Installation Over
a Monogram Warming
23 1/2”
Drawer
(59.7 cm)
Min.
Inside
9” (22.9 cm)
Max.
Min.
Inside
2” x 2” (5 cm x 5 cm) or
2” x 4” (5 cm x 10 cm)
Anti-Tip Block Against
Rear Wall, 9” (22.9 cm)
From Floor to Bottom
of Block
27 5/16”
(69.2 cm)
Max.
9 1/4”
(23.5 cm).
28 1/2”
(72.4 cm).
Double Oven Cutout
for Installation Over
a Monogram Warming
23 1/2”
Drawer
(59.7 cm)
2” (5.1 cm)
Min.
Allow 5/8”
(1.5 cm)
Overlap
on All
Sides
51 15/16”
(131.8 cm)
Max.
2” (5.1 cm)
Min.
NOTE: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
9” (22.9 cm)
Max.
9 1/4”
(23.5 cm).
Allow 5/8”
(1.5 cm)
Overlap
on All
Sides
28 1/2”
(72.4 cm)
1” (2.5 cm) Min. Above Toekick
1” (2.5 cm) Min. Above Toekick or
Adjust to Oven Installation Height
• The Monogram Warming Drawers require
5/8” (1.6 cm) overlap on all sides.
• When installing a Monogram Warming
Drawer below a single or double oven, a
separate 120V, 60 Hz, properly grounded
receptacle must be installed. Refer to
installation instructions packed with the
Warming Drawer for specific installation
requirements.
NOTE: Additional clearances between cutouts
may be required. Check to be sure the oven
supports above the Warming Drawer location
do not obstruct the required interior 23 1/2”
(59.7 cm) depth and 9 1/4” (23.5 cm) height.
• These Monogram Ovens require 3/4” (1.9
cm) overlap on both sides. Allow 1” (2.5 cm)
Min. for top overlap and clearance to upper
doors.
A6
2” x 2” (5 cm x
5 cm) or 2” x
4” (5 cm x 10
cm) Anti-Tip
Block Against
Rear Wall, 9”
(22.9 cm)
From Floor
to Bottom
of Block
Cutout for Frameless Cabinets
30”
(76.2 cm)
Frameless Cabinets
Whenever possible, order 30” (76.2 cm)
frameless cabinet with the cutout sided to fit
the oven. If using stock cabinets, additional
finished filler pieces may be required to
cover the opening.
• A stock frameless cabinet cutout width
may be up to 28 3/4” (73 cm). If necessary,
add 1/2” (1.3 cm) cleats to the sides, flush
with the front edge of the side panels to
accept mounting screws.
Install 1/2”
(1.3 cm)
Cleats to
Hold Oven
Mounting
Screws
Double
51 15/16” (131.8 cm)
Single
27 5/16” (69.2 cm)
28 1/2” (72.4 cm)
Min.
28 5/8” (72.7 cm)
Max.
Cabinet Depth
23 1/2” (59.7 cm)
Min. From Inside
Back to Front of
Cabinet Frame
or Side Panel
3/4” (1.9 cm) Min.
Thick Bottom Shelf
Cut Back Flush
with Front of
Side Panel
8
Cabinetry
A7 Single Oven Cutout
for Installation Below
a Monogram Advantium
23 1/2”
Oven
(59.7 cm)
A8
Min.
Inside
Single Oven Cutout
for Installation Between
a Monogram Advantium
Oven and a Monogram
Warming Drawer
23 1/2”
(59.7 cm)
Min.
Inside
Per Advantium
Requirement
Per Advantium
Requirement
2” (5.1 cm) Min.
2” (5.1 cm) Min.
45 1/4”
(114.9 cm)
27 5/16”
(69.2 cm)
Max.
28 1/2”
(72.4 cm)
Note: Install the
oven only with
specific models
listed on the label
located on top of
the oven.
45 1/4”
(114.9 cm)
27 5/16”
(69.2 cm)
Max.
28 1/2”
(72.4 cm)
2” (5.1 cm) Min.
9 1/4”
(23.5 cm)
1” (2.5 cm) Min.
Above Toekick
NOTE: The middle rail separating the two
openings may need to be larger than the 2”
(5.1 cm) minimum shown. Always refer to the
individual installation instructions packed with
each product for specific requirements.
NOTE: Additional clearances may be
required. Check to be sure the oven
supports above the Warming Drawer
do not obstruct the required interior 23 1/2”
(59.7 cm) depth and 9 1/4” (23.5 cm) height.
The middle rail separating the openings
may need to be larger than the 2” (5.1 cm)
minimum shown. Always refer to the
individual installation instructions packed
with each product for specific requirements.
Combined Advantium and Wall
Oven Installation:
When installed in combination with a
Monogram single wall oven, use separate
electrical junction boxes.
• Refer to the Advantium oven installation
instructions for electrical requirements of
that product.
• These connections must be made
by a qualified electrician. All electrical
connections must meet National Electrical
Code or prevailing local codes.
Warming Drawer
Combined with Advantium
and Single Oven:
Install a separate 120V, 60Hz, properly
grounded receptacle. See installation
Instructions packed with each product
for specific requirements.
9
Installation Instructions
B
Electrical Connections
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
B1
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
B2
With the oven supported on a table
or platform in front of the cabinet
opening, connect the flexible conduit
to the electrical junction box as shown
below. Position the conduit in such a
manner that it will lie on top of the
oven in a natural loop when the oven
is installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
Conduit
48 1/2”
(123 cm)
long
Junction Box
5”
Location
(12.7cm)
GROUND
WIRE
BARE
GROUND
RED
WHITE
BLACK
WARNING: Improper
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed for
joining copper to aluminum and follow
the manufacturer’s recommended
procedure closely.
Place oven on a
support to assist in
connecting conduit
Strain Relief Clamp
(not included)
must be used at
Junction Box
AVERTISSEMENT :
Le raccordement inadéquat d’un
câblage résidentiel en aluminium
à des fils de sortie en cuivre peut
entraîner un risque électrique ou
d’incendie. Utilisez uniquement des
connecteurs conçus pour raccorder
du cuivre à l’aluminium et respectez
minutieusement la procédure
recommandée par le fabricant.
10
(Continued on following page)
Installation Instructions
B
Electrical Connections cont.
B3 New Construction and
B4
Four-Conductor Branch
Circuit Connection
• When installing in new construction, or
B5
• When installing in a mobile home, or
This oven is supplied with a 48” (123 cm)
long flexible conduit consisting of:
3 insulated conductors (copper)
1 bare ground conductor (copper)
Attach conductors to residence wiring as
shown by wiring diagram.
CONDUIT
FROM
OVEN
• When installing in a recreational vehicle, or
• When local codes do not permit grounding through
neutral:
BARE
COPPER
16AWG
BLACK
16AWG
a. Cut the neutral (white) lead from the crimp.
Re-strip the neutral (white) lead to expose the
proper length of conductor.
RED
16AWG
BLACK
UL APPROVED
CONNECTOR
WHITE
(NEUTRAL)
16AWG
RED
WHITE
GROUND
TO BREAKER PANEL
#12-#10 AWG COPPER
NMD90 WIRE. FUSE 20
AMP CIRCUIT BREAKER
UL APPROVED
JUNCTION BOX AND COVER
Ground
Wire
B6 Three-Conductor Branch
Circuit Connection
When connecting to a three-conductor branch circuit,
if local codes permit:
Junction Box
Cover
a. Connect the bare oven ground conductor with the
crimped neutral (white) lead to the branch circuit
neutral (white or gray in color), using a wire nut.
b. Attach the appliance grounding lead (green or
bare copper) in accordance with local codes. If the
residence grounding conductor is aluminum, see
WARNING on page 10.
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray) in
accordance with local codes, using a wire nut.
Ground and
Neutral Wires
Junction Box
Cover
d. Connect the oven red lead to the branch circuit
red lead and the oven black lead to the branch
circuit black lead in accordance with local codes,
using wire nuts. If the residence red, black or
white leads are aluminum conductors, see
WARNING on page 10.
b. Connect the oven red lead to the branch circuit
red lead in accordance with local codes, using a
wire nut.
c. Connect the oven black lead to the branch circuit
black lead in accordance with local codes, using a
wire nut. If the residence red, black or white leads
are aluminum conductors, see WARNING on
page 10.
e. Install Junction Box Cover.
d. Install Junction Box Cover.
11
Installation Instructions
C
Securing the Oven in the Opening
C1 Sliding the Oven Into
C2 Drilling the Pilot Holes
the Opening
and Mounting the Oven
a. Loop (do not tie) a 36” (91 cm) string
around the conduit before the oven is slid
into place. This will keep the conduit from
falling behind the oven.
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go
and centered.
a. Drill through the mounting holes (top and
bottom) of the side trim, for the #8 screws
provided.
Pull out on
string loop
while pushing
the oven into
the cabinet
Mounting
Hole
Locations
b. Lift oven into cabinet cutout using the oven
opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.
The screws must
be a minimum of
1/4” (0.64 cm)
from the front
of the cutout.
WARNING: Mounting
screws must be used. Failure to
do so could result in the oven
falling out of the cabinet causing
serious injury.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the
oven in a natural loop.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
AVERTISSEMENT :
Des vis de montage doivent
être utilisées. Le défaut de se
conformer à cette directive peut
occasionner la chute de four et, par
voie de conséquence, des blessures
sévères.
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 3/4” (1.9 cm) particle board
screws. These may be purchased at any
hardware store.
12
(Continued on following page)
Installation Instructions
C3 Installing the Oven
C4 Installing the Metal
Rack Supports and
Oven Racks
Bottom Trim
a. Place the bottom trim between the side
trim and against the bottom of the cutout.
Oven Rack Supports
b. Using two trim screws provided, secure
the bottom trim to the bottom edge of the
cabinet.
Place the rack support with the slotted
holes over the rear bolts and the round holes
over the front bolts. Using an adjustable
wrench, lightly secure with four nuts but
do not overtighten or the enamel could be
chipped. Repeat for the second rack support.
Slotted
holes over
rear bolts
Round
holes over
front bolts
Oven Racks
a. Place the rear rack locks over and onto
the rack supports (five rack positions are
available, including the top position).
IMPORTANT: If this unit is ever
removed from the cabinet or the oven
is ever pulled out for service, the trim
must be removed first or damage to
the trim will occur.
b. Slide the rack all the way in until the rear
rack locks are secure on the rear rack
supports, and press the front rack locks
onto the front rack supports.
Slide the rack
all the way in
and push
down to lock
the front rack
locks onto the
front rack
supports
13
Installation Instructions
D
Replacing the Oven Door
NOTE: The oven door is heavy. You
may need help lifting the door high
enough to slide it into the hinge slots.
Do not lift the door by the handle.
D1
D3
Open the oven door as far as it
will open.
D4
Push the hinge locks up against the
front frame of the oven cavity, to the
locked position.
Hinge in
Locked Position
Lift the oven door by
placing one hand on
each side. The door is
heavy, so you may need
help. Do not lift the door
by the handle.
Notch of Hinge
Securely Fitted
into Bottom of
Hinge Slot
D5
D2
With the door at the same angle as
the removal position, seat the notch of
the hinge arm into the bottom edge of
the hinge slot. The notch of the hinge
arm must be fully seated into the
bottom of the slot.
Hinge Arm
Bottom Edge
of Slot
Hinge Notch
14
Close the oven door.
Installation Instructions
Pre-Test Checklist
Remove all protective film, if present, and
any stickers.
Check that the bottom trim is installed
properly (see page 13).
Check to be sure that all wiring is secure
and not pinched or in contact with moving
parts.
Check to be sure the mounting screws are
installed and flush with the side trim (see
page 12).
NOTE TO ELECTRICIAN: You must
unplug the green wire (near where the
long flexible conduit exits the unit)
when conducting high-potential testing.
Please replug prior to operation.
Operation Checklist
Remove all items from the inside
of the oven.
NOTE TO ELECTRICIAN: The power
leads supplied with this appliance are
UL recognized for connections to larger
gauge household wiring. The insulation
of these leads is rated at temperatures
much higher than the temperature
rating of household wiring. The current
carrying capacity of a conductor
is governed by the wire gauge and also
the temperature rating of the insulation
around the wire.
Check that conduit is securely connected
to the junction box.
Turn on the power to the oven. (Refer to
your Owner’s Manual.) Verify that the bake
and broil units, and all cooking functions
operate properly.
Check that the circuit breaker is not tripped
nor the house fuse blown.
NOTE: ALUMINUM WIRING
WARNING: IMPROPER
CONNECTION OF ALUMINUM
HOUSE WIRING TO THE COPPER
LEADS CAN RESULT IN AN
ELECTRICAL HAZARD OR FIRE.
B. Splice copper wires to aluminum
wiring using special connectors
designed and UL approved for
joining copper to aluminum,
and follow the manufacturer’s
recommended connector procedure
closely.
NOTE: Wire used, location and
enclosure of splices, etc., must
conform to good wiring practice and
local codes.
A.
See your Owner’s Manual for
troubleshooting list.
If "bAd" "LInE" appears in the display
when the power is turned on, the house
wiring connections are incorrect.
15
Printed in U.S.A.
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement