Hisense Group PDP5010EU Flat Panel Television User`s manual

Add to My manuals
19 Pages

advertisement

Hisense Group PDP5010EU Flat Panel Television User`s manual | Manualzz

R

COLOUR PLASMA DISPLAY TV

USER'S MANUAL

PDP5010EU

Part No:

OSD Language Settings

Using the GENERAL SETTINGS menu

OSD LANGUAGE

CHANGE PASSWORD

GENERAL SETTINGS

LANGUAGE ENGLISH

The symbol of the dustbin barred means that this apparatus cannot be put at the rebus with not sorted waste domestic running.

It is interdict to throw with not sorted waste domestic running, of deposited on the public thoroughfare or at any other place not envisaged to this end. This apparatus contains substances being able to be harmful for the environment.

This apparatus profits from a specific treatment of recycling for the re-use of the matters which make it up.

This apparatus must be thrown only to the places envisaged. Inform near your authority to know the places of electronic collection of waste.

Your sale point must collect this apparatus against the purchase of a new one for its recycling.

The selective collection of waste electronics is to reduce the number of substance vermin not recycled and to thus contribute to the environment.

Selecting a location for

- 3-

Preparation for Using your new TV

MENU button

Connecting your TV

Caution: Do not plug the TV in until you have finished connecting all of your equipment.

Connecting to A/V equipments

To enjoy its multimedia features, you can connect your TV to A/V equipments such as VCR, DVD, STB, Satellite receiver, Camcorder, Audio amplifier etc., and select signal sources using your remote control. Connect the devices as shown below.

Notes: Please pay attention to the relationship between

Video Port and Audio Port. .

- 4 -

Preparation for Using your new TV

Connecting to A Computer

You can use your TV as a monitor/speakers for your computer by connecting through its 15pin standard RGB

interface and PC audio interface. Connect the devices as shown below.

Connecting to an antenna

To enjoy the terrestrial signal transmitted by your local TV station, you need an indoor or outdoor antenna

(not supplied). Perfect picture quality requires a good signal and generally means that an outdoor antenna must be used. The exact type and location of the antenna will depend on your particular area. Consult your

local dealer or service personnel for best advice. If you are a subscriber of your local CATV net, the outdoor or indoor antenna is not needed. Connect the equipments as the following figure.

Plug(not supplied)

COAXIAL CABLE (75W )

TWIN-LEAD FEEDER(300 W )

Adaptor (not supplied)

Loosen the screw Insert the feeder in

The signal comes from:

An outdoor antenna

An indoor antenna

CATV net

Tighten the screw

- 5 -

Using the remote control

Preparing the remote control for use

Installing the remote control batteries

1. Open the battery cover on the back of the remote control.

2. Install two AAA size(1.5V) batteries. Match the + and - signs on the batteries to the signs on the battery compartment.

3. Close the battery cover.

Note:

1.Dispose of your batteries in a designated disposal area. Do not throw batteries into fire.

2.Do not mix battery types or combine used batteries with new ones.

3.Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.

4.If you do not intend to use the remote control for a long time, remove the batteries.

5.The effective range of remote control is suggested in the figure.

-6 -

30

3m 8m

30

3m

1m

30

8m

30

1m

1

1

1

1

Using the remote control

Learning about the remote control

PIP

Sub.Ch.

Swap

Main Ch.

Power : Power on/off

Channel Number :Direct channel selction

Red/PIP :

Fast text/ Select the OFF/PIP/POP Mode

Green/Sub.Ch.:

Fast text / Select Sub. Picture source

Yellow/Swap :

Fast text /Swap between Main and Sub.picture

Blue/Main Ch. :

Fast text / Select Main. Picture source

Recall : Return to previous channel

Display :Display current channel number or input mode

P.Mode: Select picture mode

S.Mode: Select sound mode

Text : Enter Teletext mode

Mute: Mute sound

Menu :Call up /hide the main menu

<CH+> :Channel up /Cursor up

<CH-> :Channel down/Cursor down

<VOL+>: Volume up/Cursor right

<VOL-> : Volume down/Cursor left

Zoom/Sbu. Code:

Adjust zoom ration/Teletext operation : Sub. Code

Still : Snapshooting

/Reveal :

Mono,Stereo operation/ Teletextoperation : Reveal

Video/index:

Swtich to SCART1 mode and Video mode

/Teletext operation: Index

S-Video/Hold :

Switch to SCART2 mode/Teletext operation: Hold

PC/Size:

Switch to PC mode/Teletext operation: Size

YPbPr /Cancel:

Switch to YPbPr mode/Teletext operation :Cancel

DVI/Mix:

Switch to DVI / Teletext operation : Mix

Time:

Enter SLEEP menu/ Teletext operation : Time

- 7 -

Using the TV features

Understanding the TV features

Multimedia - TV receiver, Video monitor and PC display, all in one.

Wider viewing angle, 16:9 display - over 160 viewing angle, 16:9 ergonomical display panel

Digital display device - truthfully reproducing the images, without distortion or blurring, irrespective

of magnetic or geomagnetic effect.

200 channels storage

Sleep timer

Teletext with 252 pages memory

NICAM

Dual SCART interface

Multi-language OSD

Basic Operations

Power ON/OFF

1. Connect the TV to power outlet, The

Power indicator will be red and

then turn blue. Several seconds later, TV picture will display on the screen.

2. Press the <Power>

button on the remote control to turn off the TV temporarily

and the Power indicator turn red, your set is at Stand-By mode.

3. Press any button from the <Power> button ,<CH+>button ,<CH->button on the

remote control ,your set will quit Stand-By Mode and rework again.

Push the <Chanel up> or < Chanel down > Key on the front control board ,your

set also quit Stand-by Mode and rework again.

4. If you decide to shut down the TV for a long time, it is recommended that you

unplug the power cord.

POWER

INDICATOR

Signal source selection

Dear customer ,two ways for your selecting the signal source.

The first way is ,Please take your remote control:

Press the <CH+>or <CH-> button to select TV input;

Press the <Video> button to select Scart1(CVBS/RGB) input ;

Press the <Video> button once more to enter Video input ;

Press the <S-Video> button to select SCART2(Y-C)input ;

Press the <YPbPr> button to select YPbPr/YCbCr input;

Press the <PC> button to select PC input;

Press the <DVI>button to select the DVI input.

If you can not find your remote control immediately, do not worry ,the other way for your selecting signal source.

Please Push the <TV/AV> Key on the front control board , a Source OSD Menu will display on the screen. Push the <Chanel up> or <Chanel down> Key ,you can select the Signal source ,Push the <Volume up> Key to ensure your selection.

- 8 -

Select channels by numbers

To select a channel : Press the channel numbers in series to select channel directly.

For example, to seclect channel 120, Press the button 1, and 1_ _ will display on the top right corner of the screen,

then press the button 2, 12_ will display, press the button zero, you can enjoy the program of channel 120.

NOTE:1) When you changing the channel, the sound state, colour system state& sound system state graphics can be

displayed below the channel number. There are 3 sound states in this TV. If the sound is mono, the graphics

is , If the sound is stereo, the graphics is . If the sound is NICAM dual I/II, the graphics is . But the

colour system state & sound system state is you preset the state

When you changing the channel, the sound of current channel will be firstly changed to stereo or NICAM dual

according to the sound state of current channel. You can press the I/II button on the remote control to change

current sound type.

Adjust Volume

When menu is not displayed on the screen, Press the <VOL->or<VOL+>button on the remote control to adjust the volume level. Push the <Volume up> or <Volume down> Key to adjust the volume level also.

Use <Recall> button

Press the <Recall> button on the remote control repeatedly to alternate between the present channel and the previous channel.

Display channel number

Press <Display> button on the remote control to display the present channel number, but it will also disappear 3

seconds after your pressing.

Select picture modes

You can select the picture mode fromamong three preset modes and one user-set mode.

Press the < P.mode> button on the remote control repeatedly to select the desired picture mode.

Bright

Normal

Soft

User

Select sound modes

You can select the sound mode from among three preset modes and one user-set mode.

Press the <S.mode> button on the remote control repeatedly to select the desired sound mode.

Use <Still> button

Press the <Still> button on the remote control to snapshot the present picture.

Press this button again to return to normal watching.

Speech

Normal

Music

User

- 9 -

Using the TV features

Using the CHANNEL menu

CHANNEL NUM

CHANNEL

1) Press the <Menu> button to enter the main menu.

2) Press the <

3) Press the <

VOL+> or <VOL->

CH+> or <CH->

button to select the item CHANNEL.

button to select CHANNEL NUM.

CHANNEL NUM

SOUND SYSTEM

4) Press the < VOL+> or <VOL-> button to select the present channel.

AUTO SEARCH

MANUAL SEARCH

SOUND SYSTEM

FINE TUNE

1) Press the <Menu> button to enter the main menu.

SKIP

CHANNEL EDIT

2) Press the < VOL+> or <VOL->

3) Press the < CH+> or <CH-> button to select the item CHANNEL.

button to select SOUND SYSTEM.

4) Press the < VOL+> or <VOL-> button to switch among I, B/G, D/K, L and L` .

Suggestion: Please refer to the system of your country to set the SOUND SYSTEM before you take AUTO SEARCH

or MANUAL SEARCH.

AUTO SEARCH

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.

3) Press the <CH+> or <CH-> button to select AUTO SEARCH.

4) Press the < VOL+> button to start auto searching.

MANUAL SEARCH

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.

3) Press the <CH+> or <CH-> button to select MANUAL SEARCH.

4) Press the <VOL+> or <VOL-> button to start searching.

FINE TUNE

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.

3) Press the <CH+> or <CH-> button to select FINE TUNE.

4) Press the <VOL+> or <VOL-> button to start searching.

SKIP

1) Press the <Menu> button to enter the main menu.

2) Press the < VOL+> or <VOL->

3) Press the < CH+> or <CH-> button to select the item CHANNEL.

button to select SKIP.

4) Press the < VOL+> or <VOL-> button to skip or un-skip the present channel.

NOTE: The 'skipped' channels cannot be accessed by

If you want to access

and the 'skipped' channels will be appeared.

< CH+> or <CH-> .

'skipped' channels ,please input the channel number by digit button,

CHANNEL EDIT

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item CHANNEL.

3) Press the <CH+> or <CH-> button to select CHANNEL EDIT.

4) Press the <VOL+> button to enter CHANNEL EDIT.

5) Press the <Menu> button to go back to the previous level.

-10 -

Using the TV features

Using the PICTURE menu

1) Press the <Menu> button to enter the main menu.

2) Press the < VOL+> or< VOL-> button to select the item

PICTURE PARAMETERS.

3) Press the < CH+> or< CH-> button to select the item you

want to adjust.

4) Press the < VOL+> or <VOL-> button to adjust the level.

5) Press the <Menu> button to go back to the previous level.

The adjusted data is memorized automatically in the user mode.

PICTURE PARAMETERS

BRIGHTNESS

CONTRAST

SATURATION

WARMER

WARM

NORMAL

COOL

COOLER

1)Press the <CH+> or <CH-> button to select the item COLOUR TEMP ,

2)Press the <VOL+> button enter next level. There are five modes in COLOUR TEMP item.

3)Press <CH+> or <CH-> to select your wishful item ,and then Press <VOL+>or<VOL-> to ensure.

4)Press the <Menu> button to go back to the previous level.

.

Using the AUDIO SETTING menu

Adjust audio settings

1) Press the <Menu> button to enter the main menu.

2) Press the < VOL+> or <VOL-> button to select the item AUDIO SETTING.

3) Press the < CH+> or <CH-> button to select the item you want to adjust.

4) Press the < VOL+> or <VOL-> button to adjust the level.

The adjusted data is memorized automatically in the user mode.

AUDIO SETTING

Adjust BALANCE

1) Press the <Menu> button to enter the main menu.

2) Press the < VOL+> or <VOL->

3) Press the < CH+> or <CH->

button to select the item AUDIO SETTING.

button to select the item BALANCE.

4) Press the < VOL+> or <VOL-> button to adjust the balance between the left speaker and right speaker..

The adjusted data is memorized automatically ,this item is not effective on sound modes .

Setting Surround Modes

.

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item AUDIO SETTING.

2 )Press the <CH+> or <CH-> button to select the item SURROUND ,

3)Press the <VOL+> button enter next level. There are three modes in SURROUND item.

4)Press <CH+> or <CH-> to select your wishful item ,and then Press <VOL+>or<VOL-> to ensure.

5)Press the <Menu> button to go back to the previous level.

-11 -

Using the TV features

Using the PIP menu

1)Press the <Menu> button to enter the main menu ,

2)Press the <

3)Press the <

4)Press the <

VOL+> or <VOL->

CH+> or <CH->

VOL+> to select the PICTURE IN PICTURE.

button to select the PIP SIZE, button to enter the PIP SIZE,

5)Press the <CH+> or <CH-> button ,you can select one mode

from among the OFF, PIP and PBP.

6)Press the <Menu> button to go back to the previous level.

PICTURE IN PICTURE

Note:1)WhenMainpicture is TV/SCART1/SCART2/VIDEO,the Sub Picture is YPbPr/PC/DVI.

2)WhenMainpicture is YPbPr/PC/DVI,the Sub Picture is TV/ SCART1/SCART2/VIDEO.

Using the TV features

Using the GENERAL SETTINGS menu

OSD POSITION

1) Press the <Memu> button to enter the main menu.

2) Press the < VOL+> or <VOL-> button to select the item

GENERAL SETTINGS.

3) Press the < CH+> or <CH->

and press <VOL+> enter it .

button to select OSD POSITION

4) Press the < VOL+>or <VOL-> button to adjust the OSD

POSITION.

5) Press the <Menu> button to go back to the previous level.

T he adjusted data is memorized automatically .

Color system

GENERAL SETTINGS

OSD POSITION

COLOR SYSTEM

OSD LANGUAGE

BLANK

TRANSPARENCY

ADVANCE

LANGUAGE ENGLISH

OSD LANGUAGE

CHANGE PASSWORD

BLANK

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item GENERAL SETTINGS.

3) Press the <CH+> or <CH-> button to select BLANK.

4) Press the <VOL+>or <VOL-> button to enable the BLANK

NOTE: When you enable the blank ,the screen will turn into blank screen saver mode in case of valid input signal.

The screen will turn into auto screen saver mode several seconds later, and get into stand-by mode 15

minutes later.

TRANSPARENCY

1) Press the <Menu> button to enter the main menu.

2) Press the <VOL+> or <VOL-> button to select the item GENERAL SETTINGS

3) Press the <CH+> or <CH->button to select TRANSPARENCY

4) Press the <VOL+> or <VOL->button to adjust this ITEM.

The adjusted data is memorized automatically .

-13 -

Using the TV features

Teletext Operations

ENTER TELETEXT MODE

Select the channel that is broadcasting the desired Teletext program.

Press < Text> button on the remote control to enter the Teletext mode ,and press the same button quit the Teletext mode..

Note:1)All the operations the below should be under the Teletext mode.

2) There are some multiplex buttons on the remote control for Teletext operation.

PAGE SELECTION

You can directly input your desired page number by pressing <0>~<9> buttons.

You can sequentially read pages by pressing <CH+> or <CH-> button.

HOLD

Some Teletext information is contained on more than one page, the pages automatically changing after a given reading

time.

Press the <Hold> button to stop the page changing.

Press the <Hold> button again to allow the page to change.

REVEAL

Some Teletext pages contain quiz or questions with hidden answers.

Press the <Reveal> button to see the answers.

Press the <Reveal> button to hide the answers again.

CANCEL

When a page is selected in Teletext mode it may take some time before it becomes available.

Press the <Cancel> button to switch to the TV mode.

When the required page is found, the page number will appear at the top of the TV picture.

Press the <Cancel> button to return to the selected Teletext page.

Note: You can change TV program while in this mode

SUB CODE

Some Teletext pages contain sub page that require you to input the sub code.

Press the <Sub. Code> button till pages/sub pages is displayed, and enter four-digit sub code for the sub page you need.

If you want to quit Sub. Code mode, press <Sub. Code> button till pages/sub pages is disappeared.

MIX

You can mix Teletext with TV pictures, which means transparent teletext.

Press the <Mix> button to get mixed effect, and press the <Mix> button again to cancel the mixed effect.

SIZE (Top/Bottom/Full)

Using SIZE to enable easier reading (larger display).

Press the <Szie> button to display the TOP HALF of the page.

Press this button once more to display the BOTTOM HALF of the page.

Press again to return to a FULL PAGE display.

Note: Changing pages reverts to a FULL PAGE display.

INDEX

Teletext index page guides you quickly to your desired page.

Press the <Index> button to jump to the index page.

TIME

Time information is contained in the teletext broadcast.

Press the <Time >button to display the time.

FAST TEXT

The RED, GREEN, YELLOW & BLIE buttons are used for quick access to colour coded pages transmitted by

FAST TEXT broadcast.

-14-

Appendix

Scart connector

See Signal Source Selection on page 8 for selecting SCART input.

Appendix

Troubleshooting

Before calling a service technician, please check the following table for a possible cause of the problem and some solutions.

Symptoms Possible Solutions

TV will not turn on

No picture, no sound

No sound, picture OK

Poor sound, picture OK

Poor picture, sound OK

Unable to select a certain channel

Make sure the power cord is plugged in, then press <Power>.

The remote control batteries may be dead. Replace the batteries.

Check if you have set the off timer.

Check the antenna/cable connections.

Press [Display] to see if you have select the right signal source.

The sound may be muted. Press < VOL+>

Check the speakers cable connections.

on the remote control or .

The station may have broadcast difficulties. Try another channel.

The station may have broadcast difficulties. Try another channel

Check the speakers cable connections.

Check the antenna connections.

The station may have broadcast difficulties. Try another channel.

Adjust the picture from the menu.

The channel may be skipped.

Poor colour or no colour

The station may have broadcast difficulties. Try another channel.

The remote control does not operate

Disorder display at power on

There may be an obstruction between the remote control and the

remote control sensor.

The batteries may be installed with a wrong polarity.

The remote control batteries may be dead. Replace the batteries.

Check if you have entered Teletext mode. Press <Text> to quit.

This may be caused by too short interval between power off and on.

Unplug the power and restart.

Cleaning and care

WARNING: Do not try to remove the cabinet back. Refer servicing to qualified service technicians.

To clean the TV screen:

1) Unplug the TV to avoid possible shock hazard.

2) Use a clean cellulose sponge or chamois cloth dampened with a solution of mild detergent and warm

water to clean the TV screen and trim. Do not use too much water as water spilled into the cabinet

can cause damage to the TV.

3) Wipe off any excess moisture with a clean dry cloth.

4) Polish the cabinet with a quality furniture polish to maintain the finish and appearance of the cabinet.

Caution: Never use strong solvents such as thinner, benzene, or other chemicals on or near the cabinet.

These chemicals can damage the finish of the cabinet.

-16 -

Specifications

Diagonal display size 50 INCHES PDP

Television system Multi- standard(PAL,SECAM)

Channel coverage

Resolution

Contrast

Brightness

Viewing angles

Power source

VHF-L: E2-S8

VHF-H: S9-S37

UHF: S38-E69

1366X768

2500:1

1000cd/m 2 o

AC100V--240V, 50/60Hz

Power consumption 500W

Audio output

Connection interface

Dimensions

Weight

7W+7W

RF input: Cable/ Antenna 1

VIDEO input: VIDEO 1

YPbPr/YCbCr 1

GRAPHIC input: Analog RGB 15pin 1

Digital RGB(DVI-D) X1

SCART INPUT: SCART1 (CVBS/RGB)

SCART2 (Y-C)

AUDIO input: AV Audio 1

Mini-jack for Stereo

AUDIO output: AV Audio 1

SCART Audio X 2

(3.5 )X1

Mini-jack for Stereo (3.5 )X1

OTHER: RS232C X 1 (for software updateing)

41inches X 25inches X 3inches

54.6Kg

Supplied accessories Remote control, Power cord

Design and specifications are subject to change without notice.

-17 -

advertisement

Related manuals

Frequently Answers and Questions

How can I connect my computer to the TV?
Connect the computer to the TV using a 15-pin standard RGB interface and PC audio interface.
How do I select channels by number?
To select a channel, press the channel numbers serially using the remote control.
What is the PIP button on the remote control used for?
The PIP button is used to select OFF/PIP/POP Mode.
How do I adjust the volume of the TV?
Press the or button on the remote control to adjust the volume level.
How can I select different picture modes?
Press the button on the remote control to select the desired picture mode among Bright, Normal, Soft, and User.
How do I use the button on the remote control?
Press the button on the remote control to snapshot the present picture. Press it again to return to normal viewing.
Download PDF

advertisement