Hitachi 28LD5000TA Flat Panel Television User Manual

Hitachi 28LD5000TA Flat Panel Television User Manual
ENGLISH
28LD5000TA
28" LCD TV
USER'S MANUAL
Thank you very much for purchasing the HITACHI LCD Monitor.
Before using your monitor, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will know how to
operate the monitor properly. Keep this manual in a safe place. You
will find it useful in the future.
Notes on lnstallation Work:
This product is marketed assuming that it is installed by qualifed
personnel with enough skill and competence. Always have an
installation specialist or your dealer install and set up the product.
HITACHI cannot assume liabilities for damage caused by mistake
in installation or mounting, misuse, modification or a natural
disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the customer
and explain to the customer how to handle the product.
1
Important
Please read this User's Manual thoroughly, especially the Safety
Instructions on Page 4 to 7. Mis-use may cause damage to your LCD
monitor, which could shorten its lifespan, or cause injury to yourself.
Should you encounter any difficulty in the set-up or operation of your
monitor, firstly refer to the Troubleshooting guide at the rear of this
manual.
In the unlikely event of a problem occurring with your LCD monitor,
switch off at the mains sockets, pull out the plugs, and contact your
dealer immediately.
CAUTION
Under no circumstances remove the rear cover of your LCD monitor.
Never guess or take any chances with electrical equipment of any
kind - it is better to be safe than sorry!
Software Notice
It is prohibited for the end user of this product to copy, reverse
engineer or reverse compile the software included therein, save to
the extent permitted by law.
LCD Monitor
After the LCD monitor has been on for any length of time, you will
notice that the screen becomes warm. Please note that this is normal.
Sometimes the screen might have some tiny bright or dark spots.
Please note that this is normal.
CAUTION
To prevent scratches or damages to the LCD screen, do not knock or
rub the surface with sharp or hard objects. Clean the screen with a
soft cloth moistened with warm water and dry with a soft cloth. A mild
soap may be used if the screen is extremely dirty. Do not use harsh
or abrasive cleaners!
CAUTION
Use a soft cloth to clean the cabinet and control panel of the monitor.
When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive
cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or
cracks.
2
FEATURES
High-definition LCD display panel
The 28-inch TFT LCD panel with a resolution of 1280(H) X 768(V)
pixels, creates a high-definition, proper screen (aspect ratio:15:9)
and low-profile flat display. Free from electromagnetic interferences
from geomagnetic sources and ambient power lines, the panel
produces high-quality display images free from colour
misconvergence and display distortion.
High Performance Digital Processor
A wide range of personal computer signals can be handled, from 640
x 400, 640 x 480 VGA to 1600 x 1200 UXGA.
Easy-to-use remote control and on screen
display system
The remote control included eases the work of setting display controls.
Further, the on-screen display system, displays the status of signal
reception and display control settings in an easy-to-view fashion.
Power saving system
The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its
power consumption while it is idle.
TruBass
TruBass, SRS and (O) symbol are trademarks of SRS Labs,Inc.
TruBass technology is incorporated under license from SRS Labs, Inc.
About the Video Unit
The following functions can be obtained by the video unit.
(1) A composite/S terminal and two component terminals have been
added. A composite video output terminal is also provided as a
monitoring output.
(2) A wide range of devices other than personal computers can also
be connected.
(3) A component input is possible to switch to RGB signals from the
Menu screen.
(4) A SCART terminal is also provided for the signal of the European
standard. It operates as composite/S/RGB input terminal, or video
output terminal.
FEATURES ....................................................2
SAFETY INSTRUCTIONS ..............................4
COMPONENT NAMES ..................................8
Automatic Store ................................................................22
Signal Check ....................................................................23
Power Save Mode..............................................................23
Main Unit..............................................................................8
Remote control ....................................................................9
Loading Batteries ..............................................................9
Handling the Remote Control ............................................9
NOTES ........................................................24
TROUBLESHOOTING ..................................25
INSTALLATION INSTRUCTIONS ................11
Installation..........................................................................11
Anti-tumble measures........................................................11
Connecting to a PC ..........................................................12
Speaker Cable connection ..............................................13
Power Cord Connection ....................................................13
ENGLISH
CONTENTS
Symptoms That Seemingly Appear to be Failures ............25
Actions to Correct Abnormal Displays ..............................27
Video Unit Function ..........................................................28
Tuner Unit Function ..........................................................38
PRODUCT SPECIFICATIONS ......................49
Signal Input........................................................................50
Recommended Signal List ................................................51
OPERATING INSTRUCTIONS ....................14
Turning Power On and Off ................................................14
Input Switching ..................................................................15
Volume Adjustment............................................................15
Audio Mute ........................................................................15
Size Switching ..................................................................16
Input Signal Screen Display ..............................................16
Using the Menu Screen ....................................................17
PICTURE MENU ................................................................18
AUDIO MENU ....................................................................19
TIMER MENU ....................................................................19
FUNCTION MENU ............................................................20
SETUP MENU ....................................................................21
LANGUAGE MENU............................................................22
OTHER FEATURES ....................................22
Notes about This Manual
• The information in this manual is subject to change without notice.
• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any
comments, views or questions about our product.
• Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the
product. We are not held liable for damages caused by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior written permission is prohibited.
• The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
3
SAFETY INSTRUCTIONS
This LCD monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be
taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the user and
others, and to prevent property damage. The meanings of these symbols are described below. It is important that you read these descriptions
thoroughly and fully understand the contents.
WARNING
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to
incorrect handling.
CAUTION
This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due
to incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the symbol to the left
indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables,
penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure Disconnect the
that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be plug from the
power outlet.
dangerous.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children
are present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the
power outlet and contact your dealer.
• Do not place the monitor in a bathroom.
• Do not expose the monitor to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
• Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet
and contact your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage
and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
• Do not place anything around ventilation openings of the monitor.
• Never block ventilation openings.
• Do not put the LCD screen side up.
• Do not cover the monitor with a tablecloth, etc.
• Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the
monitor and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
4
Do not
disassemble.
ENGLISH
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead,
obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value,
type and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed
power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Surely connect
Be careful in handling the power cord and external connection cables.
the ground wire.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat,
pressure or tension to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them
because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand
holding the plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they
exit from the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this monitor.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or
clothes, rinse well with water.
• Obey the local laws on disposing the battery.
• FOR THE CUSTOMERS IN THE U.K.
THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE
NOTES ON THIS PAGE.
IMPORTANT FOR UNITED KINGDOM
WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS
The mains lead on this equipment is supplied with a molded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
Should the fuse need to be replaced, an ASTA or BSI approved BS 1362 fuse must be used of the same rating. If the fuse cover is detachable
never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of
the plug. Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to
reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first removed the fuse, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
WARNING: THIS EQUIPMENT MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code :
Green and Yellow = Earth, Blue = Neutral, Brown = Live.
As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the earth
symbol
or coloured GREEN or GREEN and YELLOW.
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN
must be connected to the terminal marked with the letter L or coloured BROWN or RED.
Green & Yellow
to Earth
Brown to Live
Fuse
Blue to Neutral
Cord Clamp
5
SAFETY INSTRUCTIONS(continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in
households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Disconnect the
plug from the
power outlet.
PRECAUTIONS
• Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
• How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
• How to clean the LCD panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the LCD screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a
soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or
abrasive cleaners.
• How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and
wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially
because they would cause discoloration, scratches or cracks.
6
• Prevention of an obstacle to Radio receivers
ENGLISH
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
- Keep the monitor away from Radio.
- Adjust Radio antennas in order for the monitor not to receive interference.
- The antenna cable of Radio should be kept away from the monitor.
- Use a coaxial cable for antenna.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
• Precautions for the cable connection
- Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing
connections.
- Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc..
- Use a plug with ground terminal and make sure that it connects to the ground.
• Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
• Precautions for the installation
- Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand
or legs with the fixings provided according to the instructions.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
- This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the
front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
- Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
- Only use the attachments/accessories specified by the manufacturer.
- Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
• Other precautions
- Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a
stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or
handicapped people.
- Disposal of this product may require specific instructions pertaining to your resident region.
- Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
7
COMPONENT NAMES
Front
Main Unit
Cabinet
(front frame)
Panel
Control panel
• These buttons are located on
the top.
INPUT SELECT button
29
(OK button) 15
Remote-control
9
receiver
Indicating lamp 14
40
PROGRAM UP button
( SELECT button)
• The main power switch is located at the back, on the
lower surface.
Main power switch 14
SUB-POWER button
PROGRAM DOWN
button ( SELECT
button)
VOLUME
UP/DOWN
buttons 15
MENU button 17
(
ADJUSTbuttons)
14
(28")
• ( ) indicates the function while the MENU is displayed on the screen.
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be gripped on the
top of the panel and the unit should then be held at the
base on both sides for stability as shown.
Rear
speaker
terminals
speaker
terminals
13
13
External device connection terminals
RGB input terminals 12
8
COMPONENT NAMES
POWER ON / OFF button
PICTURE MODE button
RECALL button
INPUT SELECT button
MENU button
AUDIO MODE button
SURROUND button
CH I / II button
MULTI PICTURE (PinP) button
Buttons for MULTI PICTURE mode
RETURN button
SELECT / ADJUST buttons (
D/N
i+
I / II
A/B
MENU
PROGRAM UP / DOWN buttons
2-4-12
P+
-
VOLUME UP / DOWN buttons
DV D
MUTE button
FREEZE button
ZOOM button
FREEZE
DVD CONTROL buttons
ZOOM
PROGRAM SELECT buttons
)
+
OK
P-
OK button
ENGLISH
Remote control
1
2
4
5
6
7
8
9
PROGRAM UP / DOWN buttons
3
0
AV1
AV2
AV3
AV4
RGB1
RGB2
RGB / VIDEO buttons
TIME button
Loading Batteries
1. Open the battery cover.
• Slide back and remove the battery
cover in the direction of the arrow.
Handling the Remote Control
Use the remote control within about 5 m from front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
• Load two Size AA batteries included
observing the correct polarities.
With in 30
degrees
With in 30
degrees
About 3m
About 3m
About 5m
D / N
i+
3. Close the battery cover.
I / II
A /B
MENU
2-4-12
P+
-
+
OK
P-
• Replace the battery cover in the
direction of the arrow and snap it back
into place.
D VD
FREEZE
ZOOM
1
2
4
3
5
7
6
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
ATTENTION
CAUTION
• Do not use new and old batteries together. The batteries could
explode or leak, resulting in fires, physical injury, or stains.
• When loading batteries, observe their correct polarities as marked
on the product. If loaded in the wrong direction, the batteries
could explode or leak, resulting in fires, physical injury, or stains.
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace the
batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such light.
9
COMPONENT NAMES (continued)
Remote control (continued)
PICTURE MODE
AUDIO MODE
Y
You may recall the sound mode by pressing
this button. Each time pressed, sound mode
is changed in following sequence.
ou may recall the picture mode by
pressing this button. Each time pressed,
picture mode is changed in following
e uence
s
q
.
Natural
Dynamic
D/N
Movie
Music
Favourite
Speech
MATRIX SURROUND
INPUT SELECT
Press this button to change input
i +
Press this button to set Matrix
Surround On or Off.
I / II
m ode.
MULTI PICTURE
RECALL
ou can see the input mo e status on
the screen y pressin the utton
Y
A/ B
MENU
2-4-12
d
b
g
b
.
P+
-
+
OK
MUTE
DVD CONTROL
ou can use these uttons to operate
the selecte ran o DVD player
FREEZE
b
d
f
.
ZOOM
3
4
5
6
Press this button to change the
picture to freeze mode. Press it again
to return to normal picture.
7
8
9
ZOOM
AV1
Pressing this button can indicate the
time by On-Screen display when
receiving a TV program on the screen
including TELETEXT service with the
time in ormation
f
10
.
FREEZE
2
0
TIME
Press this button to turn off the set
sound. When press again or the _
volume up button will restore the sound.
1
PROGRAM SELECT
Press these buttons to select a TV
program directly.
models only.
In multi-picture mode, pressing this
button will change the multi-picture
mode.
DVD
d b
CH I/II
This button is for A2 / NICAM
MULTI MODE
P-
Y
Press this button to change the
screen to multi-pictures. Press it
again to return to normal picture.
AV2
AV3
AV4
RGB1
RGB2
Press this button can change Picture size.
INSTALLATION INSTRUCTIONS
ENGLISH
Installation
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or
dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries
or property damage caused by use of other mount units or improper installation.
10cm (4 inches) or more*
CAUTION
• Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this work
yourself. Ask your dealer to provide the name of a qualified installer.
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop setup) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not
blocked.(✻)
Clamp
Cord
or
chain
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
Hook
cord or chain
Chain
clamp
Wall or Pillar
Securing desktop
1) Using wood screws (two), fasten the set to the clamping screw holes on the rear of the stand as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Wood screw
Two places
11
Read SAFETY INSTRUCTIONS (
proceeding to these steps:
4
to
7
) carefully to ensure maximum safety before
• Choose an appropriate site and install the product on a level table where the stand is secure.
• Install the monitor to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
• See "Product Specifications" concerning the specifications of this device. 51
~
52
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the display signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with
the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the
personal computer manufacturer or your local retail dealer.
Monitor rear panel
Speaker (L)
Speaker (R)
Power cable
connector
Power cord
Power
cord
(DVI)
(D-sub)
3.5mm
Stereo
mini jack
To signal
output
terminal
To signal
output
terminal
To audio
output
terminal
PC
12
INSTALLATION INSTRUCTIONS (continued)
ENGLISH
Speaker Cable Connection
Power Cord Connection
Connect the power cord, after completing all other connections.
①
➁
① Connect the power cord to this device.
➁ Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided.
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
13
OPERATING INSTRUCTIONS
Turning Power On and Off
• To turn the monitor power ON, press the main power
Indicating lamp
Main power switch
switch on the monitor main unit to ON, and then press
the SUB POWER button or the ON/OFF or ON button on
the remote control.
• To turn the monitor power OFF, press the SUB POWER
button or the ON/OFF or OFF button on the remote
control, and then press the main power switch on the
monitor main unit to OFF.
• During normal use, the main power switch is set in the ON
position, and the monitor can then be turned ON/OFF using the
SUB POWER button or the ON/OFF button on the remote control.
(28")
Indicating lamp
Indicating
lamp
Power status
Operating
Off
Off
When the main power switch is set
to OFF.
Lights red
Off
(standby)
When the main power switch is
ON, and the OFF button on the
remote control or the SUB POWER
button on the top of the front of the
frame is OFF.
On
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the top of the front of the
frame is ON.
Off
(Power Save)
When the main power switch is
ON, and the ON button on the
remote control or the SUB POWER
button on the top of the front of the
frame is ON.
However, the state in POWER
SAVE mode
Lights green
SUB-POWER button
POWER ON/OFF
button
When the indicating lamp lights in orange or the message “No Sync.
Signal”, “Power Save” or “Invalid Scan Freq.” appears on the
screen, there is something unusual about the status of reception.
See “Power Save Mode” or “Symptoms That Seemingly Appear to be
Failures.” 23
25
D / N
i+
I / II
A /B
MENU
2-4-12
P+
-
+
OK
PD VD
FREEZE
ZOOM
1
2
3
4
5
6
8
9
7
0
AV1
14
AV2
Lights orange
AV3
AV4
RGB1
RGB2
ATTENTION
• Avoid repeatedly turning the monitor on and off at short time
intervals. Failures might result from such operation.
• Turn off the main power switch before leaving the monitor out of
use for an extended period of time.
• If a power failure occurs while the main unit is running, it would
be powered on upon recovery from the failure. Turn off the unit
main power switch before leaving the main unit.
OPERATING INSTRUCTIONS (continued)
ENGLISH
Volume Adjustment
VOLUME UP/DOWN
buttons
INPUT SELECT button
D / N
i+
I / II
A /B
MENU
2-4-12
P+
-
+
OK
VOLUME
UP/DOWN buttons
PD VD
Audio Mute
MUTE button
FREEZE
The audio volume can be temporarily mute by pressing
the MUTE button of the remote control.
ZOOM
1
2
3
4
5
6
8
9
7
Volume setting value
0
AV1
AV2
AV3
AV4
RGB1
RGB2
Volume 15
RGB buttons
Adjustment status guide display
(The display colour will change to magenta.)
Input Switching
• When a button is pressed, the volume adjustment
status guide (magenta) will be displayed.
• The volume setting can be lowered by pressing the VOL- button
while the audio is mute.
• The muting can be cancelled by pressing the VOL+ button or
MUTE button while the audio is mute.
When the MUTE button of the remote control is pressed
again, the audio will be restored and the volume display
(green) will appear.
15
RECALL button
i+
I / II
A /B
MENU
2-4-12
P+
-
+
OK
PD VD
FREEZE
ZOOM
ZOOM button
Size Switching
Each time the ZOOM button of the remote control is pressed, the screen display area will change in sequence and the
status will be displayed at the bottom of the screen.
Normal
Real*
Full
Zoom3
Zoom1
Zoom2
Display area selection diagram (RGB input)
Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that
flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On 21 can
reduce the flicker.
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control.
• The display will go out in approximately 6 seconds.
RGB
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
Off-timer
On-timer
16
OFF
ON
-- -- Min.
-- -- : -- --
Input mode
Signal mode
Input horizontal frequency
Input vertical frequency
Using the Menu Screen
(On-screen display system)
D / N
i+
I / II
A /B
MENU
MENU button
SELECT/ADJUST
buttons
2-4-12
RETURN buttons
P+
-
• Refer to 18
settings.
+
OK
When the MENU button is pressed, the adjustment menu
screen will be displayed; from there, PC signal adjustment
and setting is possible by using the SELECT button,
ADJUST button and OK button.
-
22
concerning the adjustment items and the
OK button
P-
Example: Selecting the Picture screen
D VD
FREEZE
1. Press the MENU button to display the Main Menu
screen.
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
ZOOM
MENU
1
2
3
4
5
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
2. Press the OK button to display the Picture Menu
screen. (Use the
and
SELECT buttons to select
other items.)
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Back Light
Reset
Select
Return
OK
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Exit
3. Use the
and
SELECT buttons to select the item to
be adjusted and then use the
and
ADJUST
buttons to adjust (example: Contrast).
P+
P
P-
Contrast
Next / Prev
+ 31
Adjust
Return
• Press the RETURN button to return to the previous screen.
• If there is no operation for a period of one minute, the
Adjustment Menu screen will be closed automatically.
17
ENGLISH
OPERATING INSTRUCTIONS (continued)
PICTURE MENU
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
OK
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Back Light
Reset
Select OK Set
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Back Light
Reset
Select OK Set
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
OK
Contrast
Next / Prev
Reset
Return
:
:
:
:
:
:
+ 31
Adjust
Return
P+
P+
P-
P-
+ 31
– 31
0
+ 31
Off
Normal
OK
Colour Temperature
Next / Prev
Select
Reset
Return
Normal
Return
P+
P-
▼
18
▼
Picture
Contrast
Brightness
Colour
Hue
Picture Enhancement
Colour Temperature
Colour Temp.Adjust
Back Light
Reset
OK Set
Select
:
:
:
:
:
:
+ 31
– 31
0
+ 31
Off
Normal
Reset
Return
OK
Picture
Colour Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
On
Reset
Return
OPERATING INSTRUCTIONS (continued)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
P+
MENU
P-
OK
Movie
Audio Mode
▼
▼
Selected characters
Audio
Audio Mode
Treble
Bass
Balance
SRS TruBass
Matrix Surround
Perfect Volume
Reset
Select
Set
Music
Speech
Favourite
:
:
:
:
:
:
:
Movie
+ 10
– 10
0L
Middle
Off
Off
Reset
Return
ENGLISH
AUDIO MENU
R
Setup hint
Movie: This selects the audio suitable for Movie.
Music: This selects the audio suitable for Music.
Speech: This selects the audio suitable for News, Talk show etc.
Favourite: This mode should be adjusted depending on user’s
preference.
Treble
Suppresses treble.
Enhances treble.
Adjust to taste.
Bass
Suppresses bass.
Enhances bass.
Adjust to taste.
Balance
Suppresses right-side sound.
Suppresses left-side sound.
Adjust to taste.
Middle
SRS TruBass takes advance of the ability of the human ear to be able
to distinguish between two different tones. By using this ability,
TruBass gives enhanced bass sound that otherwise would not be
heard. Adjust it depending on the user’s preference.
Off
SRS TruBass
Low
High
Matrix Surround
Off
On
This features the spacious sound effects of a stadium.
Perfect Volume
Off
On
This will automatically adjust volume so each channel and input has
the same average volume level.
Reset
(off the function)
(waiting to reset)
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
TIMER MENU
P+
P-
Off Timer
On Timer
▼
Selected characters
OK
▼
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
--Min.
30Min.
60Min.
120Min.
90Min.
--(:--)
hours
(- - : )- minutes
Timer
Off Timer
On Timer
Select
Adjust
:
30Min.
: --:-Return
Setup hint
This function automatically sets the power to standby status when the
indicated time period has elapsed.
This automatically sets the power from standby to ON when the
indicated time period has elapsed. The settable time is 00:00~11:59.
Input the required time by
SELECT buttons on the remote
control.
19
FUNCTION MENU
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
P+
P-
OK
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Select
Set
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
P+
P-
Function
Wide Standard Setting
Mode Display
ID Number
Reset
▼
20
▼
Select
Set
Fill
Off
1
Reset
Return
OPERATING INSTRUCTIONS (continued)
MENU
P+
P-
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
P+
OK
P-
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
Adjust
0
+ 31
– 20
10
Reset
Exit
ENGLISH
SETUP MENU
OK
Horizontal Position
Next / Prev
Adjust
Setup
Auto Adjust
Horizontal Position
Vertical Position
Horizontal Clock
Clock Phase
Reset
Select
Return
0
Return
P+
P+
P-
P-
Adjust
0
+ 31
– 20
10
Reset
Exit
OK
Clock Phase
Next / Prev
10
Adjust
Return
P+
P-
0.7V
Off
Off
Off
On
Movie
DVI-PC
RGB
Return
▼
▼
Setup
Input Level
Frequency Display
WVGA Type
WXGA Mode
Vertical Filter
Frequency Mode
RGB1
RGB2
Select
Set
* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.
21
LANGUAGE MENU
MENU
P+
P-
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Language
English
Français
Deutsch
Español
Italiano
Norsk
Svenska
OK
Select
Return
Exit
Select a language by ▼ ▲ SELECT buttons and press the OK button.
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
• The previously recorded items will be lost.
• The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals with which
all the elements are the same or similar will be handled as the
same signal.
22
OTHER FEATURES (continued)
ENGLISH
Signal Check
Changes in the signal status are displayed on the screen as they arise.
Status
Display
The input signal is switched or
when the RECALL button is
pressed.
RGB
Action
A guide is displayed for the input
terminal and the horizontal and
vertical sync frequency.
RGB2
RGB
H : 48.4kHz
V : 60.1 Hz
OFF
ON
When the sync signal is no longer
detected.
When the input signal does not
match the monitor specifications
or is in an unstable status.
-- -- Min.
-- -- : -- --
• A guide displays No Sync.
Recheck the personal computer
Signal, and Power Save (for
power switch status and the
approx. 5 sec.)
connection status.
• When the condition continues
where the sync signal cannot be
detected, indicator lamp of
power source changes in
orange and the mode switches
to power save mode.
A guide displays Invalid Scan
Freq.
! No Sync. Signal
Recheck the input signal
specifications.
51
52
! Invalid Scan Freq.
Power Save Mode
When the RGB, RGB2 input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
RGB sync signal
Horizontal
Vertical
Yes
No
Yes
Yes
Yes
No
No
No
PC signal
Active (normal display)
Blank (no display)
Operation mode
On
Off
Indicating lamp
Lights green
Lights orange
Power consumption
155W
1W or less
Returning to operating status
• Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control.
23
NOTES
About screen defects
• High precision technology is used in the making of LCD panels but there may be dark spots (points that do not illuminate) and bright spots
(points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will
disappear and return to normalcy. This is not a malfunction.
About the panel screen
• LCD displays display images by illuminating phosphor inside the panel. Because of this, the temperature of the panel surface may rise in some
cases.Also, LCD displays are made of finely processed glass. A reinforced glass filter is not installed over the LCD panel surface so avoid
strong impact because of danger of glass breakage.
About using in a low ambient temperature
• The response speed of LCD panel becomes slow as ambient temperatre falls. This feature may cause residual images in some cases, but this
is not a malfunction. It will return to normalcy in a litlle while after the temperature becomes normal.
24
TROUBLESHOOTING
ENGLISH
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Point to check
• No picture with the power-indicating lamp
off.
• Check the way the power cable is connected.
• Press the power switch.
See page
13
14
• The message “No Sync. Signal” or “Power
Save” is displayed.
! No Sync. Signal
• No picture with the power indicating lamp
lights in orange.
• The message “Invalid Scan Freq.” is
displayed.
! Invalid Scan Freq.
No sync signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging equipment ,
etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
An input signal is not received normally.
• Check to see if the input signal matches the monitor
specifications.
• Check the way the signal cable is connected.
12
12
51
52
• The power indicating lamp is normally lit but
no picture .
• Check the contrast and brightness settings (adjust them for higher
contrast and brightness).
• Check the way the signal cable is connected.
• The display image appears flowing
slantwise.
• Text displayed across the screen appears
vertically streaked, with the characters in
vertical columns blurred.
• Adjust the dot clock frequency and phase. (Adjust the dot clock
frequency first, the dot clock phase next.)
(RGB input)
• Text displayed across the screen appears
blurred.
• A fine pattern flickers when displayed on the
screen.
• Adjust the dot clock phase for the clearest viewing.
(RGB input)
• The remote control does not work.
• Check to see if the batteries are loaded in the remote control in
opposite direction.
• Check to see if the batteries in the remote control are OK.
12
18
21
27
21
27
9
25
20
26
TROUBLESHOOTING (continued)
ENGLISH
Actions to Correct Abnormal Displays
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the
adjustments suggested below. (only for RGB2)
Figure 1
27
Video Unit Function
INSTALLATION INSTRUCTIONS
Connecting to a Video Imaging Device
(1) Make sure that the power switch of the monitor is turned off.
(2) Make sure that the power switch of the imaging device is turned off.
(3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this
device and the signal output terminal of the imaging device.
Monitor rear panel
Speaker (R)
Speaker (L)
To audio input
terminals
To composite
input terminal
Power
cord
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
DVD player
2
DVD player
1
VCR
To SCART
terminals
To audio output
terminals
To component
output terminals
To component
input terminals
Set-Top Box
To S video output
terminal
To composite
output terminal
To audio output
terminals
To SCART
terminal
To RGB,
video and audio
input terminals
[An example of connecting video imaging devices]
Use if the
video
equipment
has an
S video
input terminal
VCR
• If video equipment with an S video output terminal is used, cabling
by the S video cable is recommended to provide finer video
quality. (If the S video input terminal and the video input terminal of
AV3 connect to the monitor at the same time, S video input would
govern.)
• If the OUTPUT (MONITOR) terminal is connected to an external
monitor with a 75 Ohm terminal, it is possible to view the same
image as on the main unit. But it is possible to monitor only the
composite video signal from AV1, AV2, AV3, or AV4 input that is
displayed on the screen at the time.
With DVI-STB and RGB component setup
To component video
equipments.
Please use the connection
cable suitable for the terminal
form of video equipment.
Applicable video signals for each input terminal (See PRODUCT SPECIFICATIONS for details.
Terminal
Signal
RCA/SCART
CVBS
S-video
Component
DVI
RGB
PC
D-sub
STB
RGB
49
)
Remarks
Component
AV1
AV2
Refer to Setup Menu. 35
AV3
AV4
Refer to Setup Menu. 35
RGB1
Refer to Setup Menu. 36
RGB2
Refer to Setup Menu. 36
(
28
: Available)
OPERATING INSTRUCTIONS
P+
-
+
OK
P-
ENGLISH
D VD
FREEZE
ZOOM
ZOOM button
1
2
3
4
5
6
7
8
9
0
RGB/VIDEO
buttons
INPUT SELECT button
AV1
AV2
AV3
AV4
RGB1
RGB2
Input Switching
TV
AV1
RGB2
AV2
AV3
RGB1
AV4
Size Switching
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the
screen.
• During AV4 signal input
• During VIDEO signal input (AV1, AV2, AV3)
Panoramic
14:9Zoom
4:3
Auto
Full
C14:9L
14:9Zoom
Zoom
Full
Display size selection diagram
Set the display size to
Play a 4:3 image in a 16:9 screen faithfully.
4:3
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Panoramic
Play a 16:9 VISTA size image in the 4:3
image faithfully reproduced on the 16:9
screen.
Play a 4:3 image faithfully in a 16:9 screen
in the standard vertical size and
horizontally squeezed.*
Play a 14:9 image in a 16:9 screen
expanded vertically and squeezed
horizontally.
Play a 14:9 image expanded vertically on
the 16:9 screen.
Zoom
C14:9L
• [Auto] is the mode using the Switch signal from the equipment
connected to AV4 terminal included in SCART connector No.8 pin
which indicate the picture format of the video source. When Switch
signal has not been detected, Default Zoom setting in the Function
Menu is used to choose.
• And during some input mode except AV4, if the Switch signal is
detected under the condition that [Auto] is selected for the picture
size of AV4, the input mode will automatically transfer to AV4.
• The size will fix as Full mode and not change when receiving the
component signal of 1080i/50, 1080i/60 or 720p/60.
When you want to
Full
Input signal
Display screen
Remarks
Blanking occurs on both sides.
(4:3 signal)
(Vista)
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking may
remain at the top and bottom.
(Squeeze)
* An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a 4:3
screen
Zoom
Full
This mode is provided for the broadcasting
program with WSS code-C14:9L.
C14 : 9L
(14:9 signal)
This mode is provided for the broadcasting
program with WSS code-14:9Zoom.
14 : 9Zoom
(14:9 signal)
29
Vertical picture position can be adjusted for [Panoramic], [Zoom] , [C14:9L] and [14:9Zoom] mode as follows.
1. Press ZOOM button and
P+
P- SELECT buttons during picture size display.
2. Position display will appear.
3. Adjustment range of each picture size are as shown below.
[Panoramic]
- 12 to + 12
[Zoom]
- 31 to + 31
[C14:9L] and [14:9Zoom]
- 16 to + 16
4. When 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)
Position + 31
Press
Position - 31
Press
ATTENTION
Using a wide-screen monitor
• This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV program,
the image would appear different from the original. Take this into consideration when making screen mode choices.
• Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for
commercial or pubic viewing purposes could infringe on the copyright holder’s right protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear
and/or appear distorted in some cases. Use the 4:3 mode to view images, which were created in 4:3 mode.
This mode allows 4:3 content to be viewed without picture distortion.
30
Displaying MULTI PICTURE
If the PinP button on the remote control is pressed MULTI
PICTURE will display.
Activating the P-in-P mode from the RGB input screen
Pressing the PinP button one time will display 2 pictures.
D / N
RECALL button
i+
I / II
PinP button
A/B button
A /B
MENU
2-4-12
SELECT button
P+
-
+
OK
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB)
input.
• The speaker icon can be shifted left and right by pressing the A/B
button; the audio of the video will be output from the side on which
the speaker icon is located.
RGB2
• The sub-screen position can be
AV1
selected up and down by pressing
SELECT buttons.
• The sub-screen can be selected with
the AV1, AV2, AV3, and AV4 buttons
(Subfrom the status that the speaker icon
screen)
appears on the left side of AV✱ as
shown in the diagram to the right.
• Pressing the PinP button again or the RETURN button will cancel
the 2 pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when
sub-screen is the component signal of 1080i/50 or 1080i/60.
AV1: Displays the VIDEO input signal of the sub-screen.
P-
Activating the Split mode from the video input screen
D VD
Pressing the PinP button one
time will display 2 pictures.
FREEZE
1
2
3
4
5
6
8
9
7
0
2 Pictures (Split)
Input terminal
Main
Sub
RGB1
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
1080i/50
1080i/60
720p/60
STB
RGB2
Component
AV1
~AV4
AV1
AV2
AV1~AV4
PAL
NTSC3.58
SECAM NTSC4.43
AV1
AV2
• The speaker icon can be shifted left
and right by pressing the A/B
button; the audio of the video will be
output from the side on which the
speaker icon is located.
• The same video input mode cannot
be selected for both screens at the
same time.
• Pressing the PinP button again or the RETURN button will cancel
the 2 pictures display.
• When the Video input is set to RGB Video, this Split mode is not possible.
• Refer to the table for 2 pictures (Split) mode.
ZOOM
576i
576p
AV1, AV2
RGB1
RGB2
480i
1080i/50 1080i/60 720p/60 STB Component
480p
(
Main
Sub
: Available)
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not
change to power save mode.
• Please be careful since image retention will occur if display is left in a MULTI PICTURE display state for a long period of time.
Input Signal Screen Display
The input signal status can be displayed on the screen
by pressing the RECALL button of the remote control.
VIDEO
AV1
Composite
Input mode
Signal mode
• The display will go out in approximately 6 seconds.
Off-timer
On-timer
OFF
ON
-- -- Min.
-- -- : -- --
31
ENGLISH
OPERATING INSTRUCTIONS (continued)
PICTURE MENU
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
OK
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
Back Light
Reset
Select OK Set
Picture
Picture Mode
Contrast
Brightness
Colour
Sharpness
Hue
Colour Temperature
Contrast Mode
Back Light
Reset
Select OK Set
Dynamic
+31
-31
0
+15
0
Normal
Normal
OK
Picture Mode
Next/Prev
Reset
Return
Dynamic
Return
Select
P+
P+
P-
P-
Dynamic
+31
-31
0
+15
0
Normal
Normal
OK
Reset
Return
Contrast Mode
Next/Prev
Select
Normal
Return
YNR
Next/Prev
Off
Return
P+
P-
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Reset
Select OK Set
Picture
YNR
CNR
Film Mode
PAL Comb Filter
LTI
CTI
Black Enhancement
Auto Colour
Reset
Select OK Set
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
OK
Select
P+
P+
P-
P-
Dynamic
Off
Off
On
On
Off
Off
Off
Off
Reset
Return
OK
Auto Colour
Next/Prev
Off
On/Off
Return
P+
P-
Picture
Colour Temp. Adjust
Colour Management
Colour Decoding
Select OK Set
Dynamic
OK
Return
Picture
Colour Temp. Adjust
Amplitude
Red
– 63
Green
0
Blue
– 31
Cut Off
Red
+ 31
Green
0
Blue
+ 31
Reset
Select
On/Off
On
Reset
Return
P+
P-
Picture
Colour Temp. Adjust
Colour Management
Colour Decoding
Select OK Set
Picture
Colour Management
Dynamic
On
OK
Magenta
Red
Yellow
Green
Cyan
Blue
Return
Reset
Select
+ 60
+ 30
0
+ 60
+ 30
0
Reset
Return
On/Off
P+
P-
Picture
Colour Temp. Adjust
Colour Management
Colour Decoding
Select OK Set
Picture
Colour Decoding
Dynamic
OK
Return
RGB
Red
Green
Colour
Hue
R
G
Reset
Select
32
B
0
+ 60
0
+ 31
Reset
Return
Exit
OPERATING INSTRUCTIONS (continued)
▼
▼
ENGLISH
PICTURE MENU (continued)
33
▼
▼
Selected characters
Off
Colour Management
Magenta
Turn On when the original balance of each colour is required to adjust
depending on the user’s preference.
On
Magenta is weakened.
Magenta is strengthened.
Red is weakened.
Red is strengthened.
Yellow
Yellow is weakened.
Yellow is strengthened.
Green
Green is weakened.
Green is strengthened.
Cyan
Cyan is weakened.
Cyan is strengthened.
Blue
Blue is weakened.
Blue is strengthened.
Red
RGB
Colour Decoding
Red
R
G
B
Darkens red only.
Lightens red only.
Green
Darkens green only.
Lightens green only.
Colour
Darkens colours.
Lightens colours.
Enhances red and weakens
green.
Enhances green and weakens
red.
Hue
Setup hint
This adjusts listed colours individually to make them either deeper or
more pure. These settings are independently stored in each of the 4
Colour Temperature modes.
Select the single colour screen when that is required to adjust R/G/B
level individually depending on the user’s preference. And set it back
to RGB mode that indicates all colour after adjusting.
Press the OK button every time the setting is changed.
This adjusts R/G/B level or tint to make the colour appear natural for
the user’s preference. These settings are independently stored in each
of the 4 Colour Temperature modes.
FUNCTION MENU
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
P+
P-
OK
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Reset
Select
Set
Off
On 60Min.
Off
Off
Split
Panoramic
Reset
Return
P+
P-
Function
Wide Standard Setting
Mode Display
ID Number
Reset
Select
Video Power Save
Default Zoom
34
▼
▼
Selected characters
Off
On
Panoramic
4:3
14:9 Zoom
Set
Fill
Off
1
Reset
Return
Setup hint
This is used to reduce power consumption for video input when there
is no video signal. Setting it On will leads the monitor to the standby
mode when the AV input with no signal is selected.
This selects the screen display size that appears first when the power
turned on.
OPERATING INSTRUCTIONS (continued)
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
P+
MENU
P-
OK
Setup
System
Colour System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
OK Set
ENGLISH
SETUP MENU
Setup
Colour System
System 1
OK
AV1
AV2
AV3
AV4
Monitor
DVI-STB
Component
HDTV
Return
Select
Auto
PAL
SECAM
PAL
Return
Exit
P+
P-
Setup
System
Colour System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
OK Set
Setup
Video Input
System 1
OK
AV1
AV2
Monitor
DVI-STB
Component
HDTV
Return
AV4
Select
Auto
Composite/Component
Auto
S.Video
Return
Exit
P+
P-
Setup
System
Colour System
Video Input
Audio Input
Scart Output
RGB1
RGB2
Select
System1
System
OK
Monitor
DVI-STB
Component
HDTV
Return
▼
▼
Selected characters
OK Set
System 1
System2
Setup
Audio Input
AV1
AV2
AV3
AV4
Select
Stereo
L/Mono
Stereo
L/Mono
Return
Exit
Setup hint
Do not change the original setting.
(System1 : Europe/Asia, System2 : North America)
Colour System
AV1
Auto
PAL
SECAM
NTSC3.58
NTSC4.43
This should correspond to the colour system of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The system of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
• When the component signal is received, this would be not available
(grayed out).
AV2
AV3
(Same to AV1)
AV4
Video Input
AV1
Auto
HDTV
AV2 (1st step)
RGB
Composite/Component
This should correspond to the signal mode of the signal from the
equipment that is connected to AV2 video input terminal.
AV2 (2nd step)
Auto
HDTV
This step should be set only when [Composite/Component] is selected on
the 1st step. And the procedure is same to AV1.
AV4
S.Video
SDTV/DVD
This should correspond to the signal mode of the signal from the
equipment that is connected to AV1 video input terminal.
• Normally, set this to Auto. The signal mode of the input signal will be
automatically recognized.
• If the input signal contains much noise or has a low level at Auto and the
operation is found erratic, set this to match the input signal.
SDTV/DVD
Composite
• If the signal from the equipment that is connected to AV4 Scart input
terminal is S.Video or Composite, set this to correspond to that signal.
• If the signal is RGB, it will be automatically recognized and this setting
will have no effect.
35
▼
▼
OTHER FEATURES
Automatic Store
Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.
• The previously recorded items will be lost.
36
TROUBLESHOOTING
ENGLISH
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
• The screen becomes dark and the images cannot be seen
during VCR special playback (fast forward, rewind).
Point to check
See page
• This sometimes occurs when a component output VCR such as
the 480i is connected.
This is not a malfunction; therefore, please take note that this may
occur. When it does occur, change to composite output, or S.video
output.
–
37
Tuner Unit funchion
[Buttons for TELETEXT Mode]
SUBTITLE button
D/N
i+
TV button
I / II
TEXT button
COLOUR buttons
(RED, GREEN, YELLOW, BLUE)
2-4-12
A/B
MENU
P+
-
+
OK
PDV D
FREEZE
ZOOM
MODE button
1
2
4
5
6
7
8
9
TEXT / TV+TEXT button
3
PAGE UP / DOWN button
SUB PAGE buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
INDEX button
REVEAL button
TV / TEXT button
HOLD button
CANCEL button
U. N. L. button
TELETEXT FUNCTION
Buttons on Remote Control
TEXT
TV
TV / TEXT
TEXT / TV + TEXT
Function
Press this to use the TELETEXT services.
Press this to return to the TV mode when in the TELETEXT mode.
This switches the receiver between the TV mode and the TELETEXT mode.
In TELETEXT mode, this button switches between TV+TEXT screen (split) and TELETEXT only.
MODE
This selects the FASTEXT and FAVOURITE modes.
INDEX
This selects the P100 page.
SUB PAGE
This allows receiving of a sub page. When the button is pressed, “S✱✱✱✱” will be displayed at the top left of the screen.
SUB TITLE
Use this to access a subtitle service directly rather than through a TELETEXT service (subject to subtitle service broadcasting).
CANCEL
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required text
page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button again to
display the TELETEXT screen.
RED
GREEN
YELLOW
BLUE
Each of these buttons selects a link page displayed at the lower part of the screen.
A FAVOURITE page can also be stored in the memory using one of the colours. It can then retrieve the page stored by
pressing the appropriate colour button.
To store a FAVOURITE page :
• press the MODE button ;
• press a colour button for the FAVOURITE page ;
• enter the FAVOURITE page number to be stored and press the same colour button again to confirm.
Each time this button is pressed, the screen display mode changes through the following.
U. N. L
normal state
upper half screen enlarged
lower half screen enlarged
HOLD
REVEAL
PAGE UP / DOWN
This holds the page currently being displayed on the screen. Instead of the page number, a "
the screen. Press this button again to release the hold state.
" indicator appears at the top of
This allows hidden information (found on some teletext pages) to be displayed on the screen.
These buttons increase / decrease the TELETEXT page number.
NOTE
• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
38
INSTALLATION INSTRUCTIONS
ENGLISH
Connecting Antenna
Make sure that the power switch of the monitor is turned off.
Monitor rear panel
Speaker (R)
Speaker (L)
Power
cord
antenna
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
2
1
Precautions when connecting the antenna
• Please use a coaxial cable which is free from interference to connect the antenna. Avoid using a parallel flat
feeder wire as interference may occur, causing reception to be unstable and stripe noise to appear on the
screen.
• Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor
antenna.
• Keep the power cord as far away from the antenna wire as possible.
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not
provided) for RF LEADS to reduce the noise.
39
OPERATING INSTRUCTIONS
The functions of the buttons located on the bottom
of the monitor change as shown below:
POWER ON/OFF
button
D/N
i+
I / II
INPUT SELECT
button
A/B
MENU
PROGRAM UP/DOWN
buttons
2-4-12
P+
-
+
OK
P-
VOLUME
UP/DOWN buttons
DV D
FREEZE
SUB-POWER button
ZOOM button
VOLUME UP/DOWN
buttons(
ADJUST buttons)
PROGRAM UP/DOWN button
(
SELECT button)
INPUT SELECT button
(OK button)
MUTE button
ZOOM
1
2
3
4
5
6
7
8
9
PROGRAM SELECT
buttons
0
RGB/VIDEO
buttons
MENU button
AV1
AV2
AV3
AV4
RGB1
RGB2
• ( ) indicates the function while the MENU is displayed on the screen.
Input Switching
Size Switching
• Input can be switched by pressing the AV1, AV2, AV3,
AV4, RGB1 or RGB2 buttons of the remote control. And
the way to return to a TV channel is as follows:
• Pressing INPUT SELECT button at RGB2 input screen.
• Pressing some PROGRAM SELECT buttons and select a TV
channel.
• Pressing PROGRAM UP/DOWN buttons at the screen without
OSD(On-screen display).
• Input can be switched in the sequence of TV ➔ AV1 ➔
AV2 ➔ AV3 ➔ AV4 ➔ RGB1 ➔ RGB2 by pressing the
INPUT SELECT button of the monitor or the remote
control.
TV
RGB2
40
AV1
AV2
RGB1
AV3
AV4
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the
screen.
• During TV mode
Auto
Full
14:9Zoom
Zoom
C14:9L
• [Auto] is the mode using WSS (Wide Screen Signals) which
identify the picture format movies and programs are broadcast in.
Various broadcast stations now transmit WSS. It can be detected
and the monitor automatically switch to the correct format.
However, some broadcasters do not transmit WSS, so this
monitor will not recognize which format is being transmitted.
Therefore, Default Zoom setting in the Function Menu is used to
choose when a WSS has not been sent or has not been detected.
D/N
RECALL button
i+
MULTI PICTURE
button
I / II
A/B
MENU
SELECT buttons
2-4-12
MULTI MODE
button
A/B button
P+
-
+
OK
PDV D
FREEZE
ZOOM
Displaying MULTI PICTURE
If the MULTI PICTURE button on the remote control is
pressed, multi pictures will display. And then three types
of the screen can be selected by pressing the MULTI
MODE button on the remote control.
The multi picture mode will change in the following
sequence each time the MULTI MODE button is pressed.
2 pictures (Split)
4 pictures
PROGRAM UP/DOWN
buttons
1
2
4
5
3
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
12 pictures
Activating the Split mode from the TV screen
Pressing the MULTI PICTURE button one time will display 2 pictures.
• The speaker icon can be shifted left and right by pressing the A/B button; the audio will be output from the
side on which the speaker icon is located.
• The same signal input cannot be selected for both screens at the same time.
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
control.
• The signal input mode of picture-A or picture-B (the one that the speaker icon is located on) can be selected
by pressing INPUT SELECT button on the remote control.
• Pressing the MULTI PICTURE button once again will cancel the multi picture mode.
• When the Video input is set to RGB Video, multi picture mode is not possible.
• Refer to the table for 2 pictures (Split) mode. 42
5
AV1
A
B
Activating the 4 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 2 pictures mode will display 4 pictures.
AV1
• Press [A/B] button to select picture A or picture B indicated by a red triangle. For pictures on right, press
SELECT buttons to select picture. The selected channel number would change green.
• The TV channel can be changed by pressing the
and
PROGRAM UP/DOWN buttons on the remote
control.
• The audio can only be output from picture A in 4 pictures mode.
• The same signal input mode cannot be selected for each screens at the same time.
• Pressing the MULTI PICTURE button at the 4 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 4 pictures.
• Refer to the table for 4 pictures mode. 42
Activating the 12 pictures mode from the TV screen
Pressing the MULTI MODE button one time at the 4 pictures mode will display 12 pictures.
• Starting from channel 1, preset channels will automatically display in sequence on the 12 windows.
• This function activates only in TV mode.
• After several seconds, it refreshes the picture one by one.
• Pressing the MULTI PICTURE button at the 12 picture mode will cancel the multi picture mode. And then,
pressing the MULTI PICTURE button again will display the 12 pictures again.
• Pressing the MULTI MODE button at the 12 picture mode will display the 2 pictures (Split) mode.
A
B1
8
B2
6
B3 11
1
2
3
4
5
6
7
8
9
10
11
12
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the multi picture display, the mode will not change to
power save mode.
• Please be careful since image retention will occur if display is left in a multi picture display state for a long period of time.
41
ENGLISH
OPERATING INSTRUCTIONS (continued)
2 Pictures (Split)
Input terminal
Sub
Main
AV1
~AV4
AV1~AV4
AV1, AV2
RGB1
RGB2
TELE
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB Component TEXT
SECAM NTSC4.43 576p 480p
Main
Sub
PAL, SECAM
NTSC3.58/4.43
576i, 576p
480i, 480p
AV1
AV2
1080i/50
1080i/60
720p/60
RGB1
STB
RGB2
Component
(
: Available)
4 Pictures
Input terminal
Sub
Main
AV1
~AV4
AV1~AV4
AV1, AV2
RGB1
RGB2
TELE
PAL
NTSC3.58 576i 480i
1080i/50 1080i/60 720p/60 STB Component TEXT
SECAM NTSC4.43 576p 480p
Main
Sub 1
PAL, SECAM
Sub 2
NTSC3.58/4.43
576i, 576p
Sub 3
480i, 480p
AV1
AV2
1080i/50
1080i/60
720p/60
RGB1
STB
RGB2
Component
(
Input Signal Screen Display
The TV channel status can be displayed on the screen by
pressing the RECALL button of the remote control.
• The display will go out in approximately 6 seconds.
TV
Off-timer
On-timer
42
1
ABCDE
OFF
ON
-- -- Min.
-- -- : -- --
I
TV position
Name
Sound mode
Sound system
: Available)
OPERATING INSTRUCTIONS (continued)
i+
ENGLISH
D/N
I / II
A/B
MENU
2-4-12
P+
-
+
OK
PDV D
FREEZE
FREEZE button
ZOOM
1
2
4
5
3
6
7
8
9
0
AV1
AV2
AV3
AV4
RGB1
RGB2
Picture Freezing
[Split]
When the FREEZE button on the remote control is pressed, the screen transfers into the
freeze mode.
• There are two types of freezing screen mode, Split and Strobe. These are possible to select at the “Freeze
Mode” setting of the Function Menu.
• The Split mode will display 2 pictures from the same source on the screen with one active picture and the
other still.
• The Strobe mode will display 12 pictures with the last picture active, while other 11 windows are still.
• Pressing the FREEZE button again changes the screen back to the normal picture.
• This function is also available from video input mode besides TV mode. Refer to the table for Freeze function
as below:
Split
5
A
B
[Strobe]
1
2
3
4
5
6
7
8
9
10
11
12
Active
Strobe
PAL, SECAM
NTSC3.58/4.43
576i
480i
576p
480p
1080i/50
1080i/60
720p/60
RGB, DVI-PC
(
: Available)
FUNCTION MENU
43
SETUP MENU
[During TV mode]
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
P+
P-
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
OK
P+
OK
P-
Off
Return
P+
P-
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
OK
Off
Return
Setup
Manual Tuning
Position
Search
Descrambler
Name
Sound System
Colour System
Skip
NR
Select
Return
99
C 22
Off
ABCDE
BG
Auto
Off
Off
Exit
Setup
Fine Tuning
Select
Prog.No.199
+56
Return
P+
P-
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Adjust
OK
Off
Return
P+
P-
Setup
Auto Tuning
Manual Tuning
Fine Tuning
Sort
Auto Off
Select OK Set
Setup
Sort
Position
100
101
102
103
104
105
106
107
OK
Off
Return
Name
ABCDE
BBC1
----BBC
FGHIJ
XYZAB
---------
Select
Setup
Auto Tuning
Country
Austria
Belgium
Croatia
Czech Republic
Denmark
Finland
France
Germany
Setup
Auto Tuning
Country
Greece
Hungary
Iceland
Ireland
Italy
Netherlands
Norway
Poland
Search
Select
Set
Return
Select
Return
Exit
Setup
Auto Tuning
Country
Portugal
San Marino
Spain
Sweden
Switzerland
Turkey
United Kingdom
Search
OK
C.S.MHz
471MHz
C25
C40
C30
S27
S41
225MHz
C51
Search
OK
Set
Return
Select
OK
Set
Return
OK
Setup
Auto Tuning
Country
Setup
Auto Tuning
Portugal
San Marino
Spain
Sweden
Switzerland
Turkey
United Kingdom
Cancel
OK
Search
Select
44
OK
Set
Scanning Channel Number: 33
OK
Return
Cancel
OPERATING INSTRUCTIONS (continued)
▼
▼
Selected characters
ENGLISH
SETUP MENU (continued)
Setup hint
Auto Tuning
Country
(Page1)
Search
–
(Page2)
(Page3)
–
Select the country name by ▼ ▲ SELECT buttons and press OK
button.
• If some required stations could not be preset in this auto tuning
function, select and preset the required station in the required
position by the manual tuning operation.
Press the OK button and it starts the auto tuning.
Manual Tuning
Position
1
2
3••••••199
AV00
Set the position number. This also can be set by ▼ ▲ PROGRAM
UP/DOWN buttons.
Search
–
–
At first, select the channel entry method, entering a two digit channel
number(CH), entering a two digit S-band number or entering a three
digit frequency(MHz), by pressing the OK button.
(C--)
–
–
Enter two digit number by pressing 0~9 NUMBER buttons. If the
number is normal, then it starts the channel search.
(S--)
–
–
Enter two digit number by pressing 0~9 NUMBER buttons. If the
number is normal, then it starts the channel search.
(--MHz)
–
–
Enter three digit number by pressing 0~9 NUMBER buttons. If the
number is normal, then it starts the channel search.
Off
Set this to Off normally. If it is set to On, AV4 (Scart) terminal operates
as TV signal output, and the screen changes to display AV4 (Scart)
input signal automatically.
On
This is used to input the name of the TV station within 5 letters. After
fixing the cursor on the first digit, select a letter by ▼ ▲ SELECT
buttons and move to next digit by
ADJUST button. Press the OK
button again after finished.
• Selectable letters are “0”~`”9”, ”A”~`”Z”, “+”, “–”, ” ”(blank),
”,”(comma) and ”.”(period) .
▼
Descrambler
Name
( :a letter)
Sound System
BG
I
Colour System
Auto
PAL
NTSC3.58
L'
DK
Select the sound system through the 5 different settings.
L
SECAM
NTSC4.43
Select the colour system through the 5 different settings.
Skip
Off
On
If this is set to On, that position will be skipped while selecting
positions by PROGRAM UP/DOWN buttons.
This is automatically set to On for those non-broadcasting channels.
NR
Off
On
If this is set to On, it helps to reduce the noise interference visible on
the screen, especially in the weaker signal reception areas.
Fine Tuning
After completing the fine-tuning, press the RETURN button to exit this
Decreasing the frequency Increasing the frequency
mode.
data for the main tuner
data for the main tuner.
• The variable range is -56 ~ +56.
Sort
(A Line of position List)
–
–
Off
Auto Off
Press OK button at the a line that is required to change order, then
the characters will change to green. And move it up or down in the
list by pressing ▼ ▲ SELECT buttons. And press OK button to
complete it. Press the RETURN button to exit.
If this is set to On, the power will be turned off when there is no
transmission signal and no operation for about 10 minutes in the TV
mode.
On
[During VIDEO signal input]
1 item is added to the Menu shown in the page 35 .
Scart Output
▼
▼
Selected characters
TV
Monitor
Setup hint
TV:AV4 (Scart) output will be fixed as TV signal output.
Monitor:AV4 (Scart) output can view the image as on the main unit.
But it is possible to monitor only the composite video signal from
AV1, AV2, or AV3 input that is displayed on the screen at the time.
• If Descrambler is set to On, it will be fixed as TV automatically.
45
OTHER FUNCTIONS
A2 / NICAM / Sound Multiplex
• The CH I / II button is only useful for NICAM and sound multiplex signals.
Otherwise pressing this button will have no effect.
8
BILINGUAL / DUAL sound broadcast
NICAM [II]
When bilingual program is received, sound mode display appears in yellow as shown on
right.
Press the CH I / II button to select the sound to be heard.
Each time the button is pressed, I, II or ▼ (force mono) appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Yellow
Green
Yellow
NICAM signal received
[I]
[II]
Yellow
Yellow
NICAM [II]
NICAM [I]
Select I, II or
Green
(force mono) to hear the CH I, CH II or MONO broadcast respectively.
STEREO sound broadcast
8
When a stereo program is received, sound mode display will appear in red, and you can
press the CH I / II button to select between stereo and mono sound.
Each time the button is pressed,
or ▼ (force mono)appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
Red
Green
NICAM signal received
NICAM
Select
or
Red
Green
(force mono) to hear the STEREO or MONO broadcast respectively.
Monaural sound broadcast
When a monaural program is received, sound mode display will appear in green.
You can press the CH I / II button to select the sound mode between monaural and forced
mono (sound is same).
Each time the button is pressed,
or ▼ (force mono) appear cyclically on the screen.
8
NOTE
• If sound signal is not strong enough for quality reception, press the CH I / II button until ▼ appears on the screen to receive a clear mono sound.
• If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the CH I / II button until ▼ appears
on the screen to receive a clear mono sound.
46
OPERATING INSTRUCTIONS (continued)
ENGLISH
OTHER FUNCTIONS (continued)
DVD Player Selection
• You can use this remote control to operate the selected brand of DVD player by pressing the following buttons on the remote control
simultaneously.
Brands of DVD Player
Press
Brands of DVD Player
Press
Hitachi
RECALL
1
RCA
RECALL
9
Pioneer
RECALL
2
Mitsubishi
RECALL
0
Panasonic
RECALL
3
Onkyo
RECALL
INDEX
Toshiba
RECALL
4
Zenith
RECALL
MODE
Philips
RECALL
5
Orion
JVC
RECALL
6
Shinco
RECALL
CANCEL
Samsung
RECALL
7
Skyworth
RECALL
REVEAL
Sony
RECALL
8
Bubuko
RECALL
TV/TEXT
RECALL
SUB PAGE
Example
To operate HITACHI DVD player, press and hold the RECALL button, followed by the 1 button.
D/N
i+
I / II
A/B
MENU
RECALL button
2-4-12
P+
-
+
OK
PDV D
FREEZE
ZOOM
MODE button
1
2
4
5
3
6
7
8
9
SUB PAGE buttons
0
AV1
AV2
AV3
AV4
RGB1
RGB2
INDEX button
TV / TEXT button
REVEAL button
CANCEL button
NOTE
• Not all models of the listed brands can be operated using this remote control.
47
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Customer servicing can be hazardous.
Symptom
Possible reason
Remedy
(1) Connection of antenna cable to the TV is
poor.
(2) Corroded or poor antenna connections.
(3) Antenna has moved position.
(4) Adverse weather conditions.
(5) Transmitter problems.
(1) Make new connection and/or change antenna
plug.
(2) Make new connections or renew cable.
(3) Re-align antenna.
(4) None.
(5) Check with local Operator.
(1) Antenna has moved position.
(2) TV not tuned correctly.
(3) Adverse weather conditions.
(4) Transmitter problems.
(5) AV Input not set correctly.
(1) Re-align antenna.
(2) Re-tune or fine tune TV.
(3) None.
(4) Check with local Operator.
(5) Check the external equipment connected.
snowy picture - poor sound
multiple images - sound O.K
(1) Interference from electrical or mechanical (1) Check devices for shielding and renew if
motors, fluorescent lights, portable
necessary or move further from TV.
radios etc.
intermittent interference
(1) TV may be in AV mode.
(2) Picture/sound setting set to minimum.
(3) TV in standby or power save mode.
no picture or sound
48
(1) Press the INPUT SELECT button or 0 to 9 buttons
on your remote control to return to normal TV
mode.
(2) Check picture / sound controls (go to MAIN
MENU).
(3) Press POWER ON / OFF button.
ENGLISH
PRODUCT SPECIFICATIONS
• The monitor takes at least 30 minutes to attain the status of optimal picture quality.
49
Signal Input
DVI terminal (DVI-D)
Pin
Input signal
Pin
1
2
3
4
5
6
7
8
9
10
T.M.D.S. Data2T.M.D.S. Data2+
T.M.D.S. Data2/4 Shield
T.M.D.S. Data4T.M.D.S. Data4+
DDC Clock
DDC Data
No Connect
T.M.D.S. Data1T.M.D.S. Data1+
14
15
16
17
18
19
20
21
22
23
+5V Power
Ground (for+5V)
Hot Plug Detect
T.M.D.S. Data0T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
T.M.D.S. Data5T.M.D.S. Data5+
T.M.D.S. Clock Shield
T.M.D.S. Clock+
Input signal
11
T.M.D.S. Data1/3 Shield
24
T.M.D.S. Clock-
12
T.M.D.S. Data3-
13
T.M.D.S. Data3+
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Frame GND
RGB terminal (D-sub 15-pin connector)
Pin
Input signal
1
R (PR/CR)
2
G or sync on green (Y)
3
B (PB/CB)
4
No connection
5
No connection
6
R.GND (PR/CR, GND)
5
15
4
3
2
1
10
9
8
7
14
13
12
6
11
• When different kinds of input signals are simultaneously input to
the monitor via a graphics board or the like, the monitor will
automatically select the signals in the following priority order:
7
G.GND (Y, GND)
Sync signal type
Priority
8
B.GND (PB/CB, GND)
H/V separate sync.
1
9
No connection
H/V composite sync.
2
10
GND
sync.on Green *
3
11
No connection
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
(
*Even in the case of the recommended signals shown on the
following page, there may be instances when correct display is
not possible. In this case, use H/V separate sync, H/V composite
sync.
) : With component input
S-input connector pin specifications
Pin
Input signal
1
2
3
4
Y
Y-GND
C
C-GND
Frame
GND
1
3
2
4
Scart connector pin specifications
Pin
50
Signal
Pin
Signal
1
AUDIO OUT (RIGHT)
12 Not Used
2
AUDIO IN (RIGHT)
13 RGB-R GND
3
AUDIO OUT (LEFT/MONO)
14 GND
4
AUDIO GND
15 RGB-R / S.VHS CHROMINANCE IN
5
RGB-B GND
16 BLANKING SIGNAL
6
AUDIO IN (LEFT/MONO)
17 COMPOSITE VIDEO GND
7
RGB-B IN
18 BLANKING SIGNAL GND
8
AUDIO/RGB SWITCH / 16:9
19 COMPOSITE VIDEO OUT
9
RGB-G GND
20 COMPOSITE VIDEO / S.VHS LUMINANCE IN
10
Not Used
21 GND / SHIELD (CHASSIS)
11
RGB-G IN
20
18
16
14
12
10
21 19
17
15
13
11
9
8
7
6
5
4
3
2
1
ENGLISH
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List
51
With Composite Input(AV1~AV4 input) and S-video Input (AV3 input).
Signal mode
No.
1
2
Signal Name
NTSC4.43
NTSC3.58
PAL
SECAM
Resolution
Vertical frequency
(Hz)
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
525
59.94
15.73
—
625
50.00
15.63
—
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
15.73
15.63
—
Remarks
With R, G, B Video input (AV2 and AV4 input).
Signal mode
No.
1
Signal Name
Resolution
Vertical frequency
(Hz)
NTSC4.43/3.58
PAL, SECAM
525
625
59.94
50.00
Remarks
With component input (AV1, AV2 and RGB2-component input).
Signal mode
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
50.00
15.63
—
59.94
15.73
—
576
50.00
31.26
—
480p
480
59.94
31.47
—
5
1080i/50
1080
50.00
28.13
—
6
1080i/60
1080
60.00
33.75
—
7
720p/60
720
59.94
44.96
—
No.
Signal Name
Resolution
Vertical frequency
(Hz)
1
576i
576
2
480i
480
3
576p
4
Remarks
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal
polarities. Note that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 768 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.
52
ENGLISH
Thank You for purchasing this Hitachi Television.
In the unlikely event that this product should develop a fault, we undertake to repair
or replace any part of the product which fails due to a manufacturing defect within
12 months of the date of purchase provided that ...
1. the product has been installed and used only in accordance with the instructions
supplied with the product.
2. the product has not been repaired, maintained, or modified by any person other
than a Hitachi authorized dealer.
3. the product serial number has not been removed or altered.
•this guarantee does not apply to a product acquired second hand or for
commercial or communal use.
•this guarantee does not cover the replacement of exhausted batteries, the
adjustment of user controls, or aerial alignment.
•any parts replaced under this guarantee shall become the property of HITACHI
EUROPE LTD..
•please note that evidence of the date of purchase will be required before any
service under this guarantee is carried out.
Use the boxes provided below to record your TV’s Model and Serial Number - these are found
on the rating plate located on the rear of the LCD screen. Also, record where and when you
purchased this T.V. This information will help any future queries you may have and should be
used in all correspondence with Hitachi service centres.
MODEL
SERIAL NUMBER
DEALER/STORE
DATE PURCHASED
This guarantee does not affect your statutory rights.
In all cases of difficulty please
consult your Hitachi dealer.
53
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement