Hitachi 31KX41K, 31DX22B CRT Television User Manual

Hitachi 31KX41K, 31DX22B CRT Television User Manual
TABLE OF CONTENTS
1
31KX41K 31DX22B
HITACHI
SOLID STATE COLOR TV
31KX41K
31DX22B
OPERATING GUIDE
Your new HITACHI Color TV incorporates a host of features designed to give you
excellent performance if you follow the instructions in this manual. We recommend that
you read the following instructions and "IMPORTANT SAFEGUARDS" notice before
turning on your TV set for the first time.
This television receiver will display television closed captioning (
accordance with paragraph 15.119 of the FCC rules.
or
) in
TABLE OF CONTENTS
TABLE OF CONTENTS ............................................................................................................................ 1
IMPORTANT SAFEGUARDS .................................................................................................................. 3
POWER SOURCE................................................................................................................................ 3
BEFORE OPERATING YOUR TV SET ................................................................................................... 9
INSTALLATION .................................................................................................................................... 9
ANTENNA CONNECTIONS ............................................................................................................. 11
HOOK-UP CABLES AND CONNECTORS ........................................................................................... 13
TIPS ON REAR PANEL CONNECTIONS...................................................................................... 13
LOCATION OF CONTROLS .................................................................................................................. 14
FRONT PANEL JACKS AND CONNECTIONS.................................................................................... 14
HOW TO SELECT CHANNELS ............................................................................................................. 15
PICTURE CAUTIONS ............................................................................................................................. 17
THE GENIUS REMOTE CONTROL (CLU-692GR with P-in-P) 31KX41K......................................... 18
THE GENIUS REMOTE CONTROL (CLU-681GR without P-in-P) 31DX22B.................................... 19
HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR T.V................................................... 20
HOW TO USE THE REMOTE TO CONTROL YOUR T.V. ................................................................. 20
-SET UP- FUNCTIONS............................................................................................................................ 23
PICTURE-IN-PICTURE FUNCTIONS (31KX41K)............................................................................... 30
P IN P BUTTON.................................................................................................................................. 30
-PICTURE- FUNCTIONS ........................................................................................................................ 32
-SOUND- FUNCTIONS ........................................................................................................................... 33
USING THE GENIUS REMOTE TO CONTROL VCR FUNCTIONS.................................................. 35
1
TABLE OF CONTENTS
USING THE GENIUS REMOTE TO CONTROL CABLE BOX FUNCTIONS.................................... 36
TABLE 1. VCR Precoded remote controls for Hitachi GJ III and GJ II Remote CLU-692GR
and CLU-681GR ................................................................................................................................. 37
TABLE 2. Cable Box Precoded remote controls for Hitachi GJ III and GJ II Remote CLU692GR and CLU-681GR ................................................................................................................... 38
EXTERNAL CONNECTIONS................................................................................................................. 38
CONNECTING EXTERNAL AUDIO AMPLIFIER.......................................................................... 38
CONNECTING EXTERNAL VIDEO SOURCES .................................................................................. 39
CONNECTING MONAURAL AUDIO VCR or VIDEO DISC PLAYER ....................................... 39
CONNECTING STEREO VCR or STEREO VIDEO DISC PLAYER ......................................... 40
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT ..................................... 42
ACCESSORIES PART NUMBERS......................................................................................................... 43
TROUBLESHOOTING ............................................................................................................................ 44
RECEPTION PROBLEMS (EXTERNAL TO THE TV) ................................................................. 44
CHECK HERE BEFORE CALLING FOR SERVICE..................................................................... 44
SPECIFICATIONS ................................................................................................................................... 46
HITACHI SERVICE HOTLINE .............................................................................................................. 47
2
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
Follow all warnings and instructions marked on this television receiver.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS TELEVISION TO
RAIN OR MOISTURE.
NOTE:
• There are no user serviceable parts inside the receiver.
• Model number and serial number are indicated on back side of the set.
POWER SOURCE
This Hitachi color TV is designed to operate on 120 volts 60Hz, AC household current.
Insert the power cord into a 120 volt 60 Hz outlet.
NEVER CONNECT THE TV TO 50Hz, DIRECT CURRENT, OR ANYTHING OTHER
THAN THE SPECIFIED VOLTAGE.
CAUTION: POWER SUPPLY CORD
POLARIZED PLUG
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN
3
IMPORTANT SAFEGUARDS
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE: Never remove the back cover of the set as this can expose you to very high
voltages and other hazards. If the set does not operate properly, unplug the set and call
your dealer or service shop.
HITACHI
SAFETY POINTS YOU SHOULD KNOW ABOUT
YOUR HITACHI TELEVISION RECEIVER.
CAUTION:
* Read all of these instructions.
* Save these instructions for later use.
* Follow all warnings and instructions marked on the television receiver.
Our reputation has been built on the quality performance and ease of service of
HITACHI television receivers.
Safety is also foremost in our minds in the design of these units. To help you operate
these products properly, this folder illustrates safety tips which will be of benefit to you.
Please read it carefully and apply the knowledge you obtain from it to the proper
operation of your HITACHI television receiver.
Please fill out your warranty card at once and mail it to HITACHI. This will enable
HITACHI to notify you promptly in the improbable event that a safety problem should be
discovered in your model of product.
FOR YOUR PERSONAL SAFETY
1 This television set is equipped with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
2 When the power cord or plug is damaged or frayed, unplug this television set from the
wall outlet and refer servicing to qualified service personnel.
3 Do not overload wall outlets and extension cords as this can result in fire or electric
4
IMPORTANT SAFEGUARDS
shock.
4 Do not allow anything to rest on or roll over the power cord, and do not place the TV
where the
power cord is subject to traffic or abuse. This may result in a shock or fire hazard.
5 Do not attempt to service this television set yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
6 Never push objects of any kind into this television set through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the television set.
7 If the television set has been dropped or the cabinet has been damaged, unplug this
television set from the wall outlet and refer servicing to qualified service personnel.
8 If liquid has been spilled into this television set, unplug it from the wall outlet and refer
service to qualified service personnel.
9 Do not subject your television set to impact of any kind. Be particularly careful not to
damage the picture tube surface.
10 Unplug this television set from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
11-1 Do not place this television set on an unstable cart, stand, or table. The television
set may fall, causing serious injury to a child or an adult, and serious damage to the
appliance. Use only with a cart or stand recommended by the manufacturer, or sold with
5
IMPORTANT SAFEGUARDS
the television set. Wall or shelf mounting should follow the manufacturer's instructions,
and should use a mounting kit approved by the manufacturer.
11-2 An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart combination to
overturn.
PROTECTION AND LOCATION OF YOUR SET
12 Do not use this television set near water...for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
• Never expose the set to rain or water. If the set has been exposed to rain or water,
unplug the set from the wall outlet and refer to servicing personnel.
13 Choose a place where light (artificial or sunlight) does not shine directly on the
screen.
14 Avoid dusty places, since accumulated dust inside the TV chassis may cause failure
of the set when high humidity persists.
15 The set has slots, or openings in the cabinet for ventilation purposes, to provide
reliable operation of the receiver, and to protect from overheating. These openings must
not be blocked or covered.
• Never cover the slots or openings with cloth or other material.
• Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc.
6
IMPORTANT SAFEGUARDS
• Never place the set near or over a radiator or heat register.
Never place the set in a "built-in" enclosure, unless proper ventilation provided.
PROTECTION AND LOCATION OF YOUR SET
16-1 If an outside antenna is connected to the television set, be sure the antenna
system is grounded so as to provide some protection against voltage surges and built
up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975,
provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrode, and
requirements for the grounding electrode.
Click to see antenna grounding diagram.
16-2 Note to CATV system installer: (Only for the television set with CATV reception)
This reminder is provided to call the CATV system installer's attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
17 An outside antenna system should not be located in the vicinity of overhead power
lines or other electrical lights or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to
keep from touching such power lines or circuits as contact with them might be fatal.
18 For added protection for this television set during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage due to lightning and power-line
surges.
OPERATION OF YOUR SET
7
IMPORTANT SAFEGUARDS
19 This television set should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply at your home,
consult your television dealer or local power company. For television sets designed to
operate from battery power, refer to the operating instructions.
20 If the television set does not operate normally by following the operating instructions,
unplug this set television set from the wall outlet and refer servicing to qualified service
personnel. Adjust only those controls that are covered in the operating instructions as
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the television set to normal operation.
21 When going on a holiday: If your television set is to remain unused for a period of
time, turn the television set "off" and unplug it from the wall outlet.
IF THIS SET DOES NOT OPERATE PROPERLY
22 If you are unable to restore normal operation by following the detailed procedure in
your operating instructions, do not attempt any further adjustment. Unplug the set and
call your dealer or service technician.
23 Whenever the television set is damaged or fails, or a distinct change in performance
indicates a need for service, unplug the set and have it checked by a professional
service technician.
24 It is normal for some TV sets to make occasional snapping or popping sounds,
particularly when being turned on or off. If the snapping or popping is continuous or
frequent, unplug the set and consult your dealer or service technician.
FOR SERVICING AND MODIFICATION
8
BEFORE OPERATING YOUR TV SET
25 Do not use attachments not recommended by the television set manufacturer as
they may cause hazards.
26 When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer that have the same characteristics as
the original part. Unauthorized substitutions may result in fire, electric shock, or other
hazards.
27 Upon completion of any service or repairs to the television set, ask the service
technician to perform routine safety checks to determine that the television is in safe
operating condition.
BEFORE OPERATING YOUR TV SET
INSTALLATION
ANTENNA
Unless your TV set is connected to a cable TV system or to a centralized antenna
system, a good outdoor color TV antenna is recommended for the best performance.
However, if you are located in an exceptionally good signal area that is free from
interference and multiple image ghosts, the indoor antenna may be sufficient.
LOCATION
Select an area where sunlight or bright indoor illumination will not fall directly on the
picture screen. Also, be sure that the location selected allows a free flow of air to and
from the perforated back cover of the TV set.
To prevent damaging the TV, do not leave the set in a place where the temperature
becomes too hot. For example, exposed to direct sunlight or near a heating device, etc.
VIEWING
This TV set may be viewed from any desired distance. Most viewers prefer a distance of
9
BEFORE OPERATING YOUR TV SET
three to six feet or more, depending on screen size, for maximum eye comfort.
NOTE: Model number and serial number are indicated on the back cover of the TV set.
10
BEFORE OPERATING YOUR TV SET
ANTENNA CONNECTIONS
These sets are equipped with one VHF/UHF antenna terminal. The VHF/UHF terminal
can be used for normal TV, cable TV (CATV), a TV game, etc.
1. VHF (75 ohm) antenna/CATV
When using a 75 ohm coaxial cable system, disconnect the VHF adaptor from the VHF
75 ohm receptacle and connect the outdoor antenna or CATV cable to a VHF 75 ohm
receptacle
2. VHF (300-Ohm) antenna/UHF antenna
When using a 300-Ohm twin lead from an outdoor antenna, disconnect the (VHF or
UHF) indoor antenna leads from screws of the (VHF or UHF) adapter, and connect
outdoor (VHF or UHF) antenna leads to these screws of a (VHF or UHF) adapter.
3. When both VHF and UHF antennas are connected
Attach an optional ANT. MIXER to the TV antenna terminal, and connect the cables to
the ANT. MIXER.
Notes
1. If an outdoor antenna/CATV is to be used, disconnect the indoor antenna. Do not leave
both the indoor and outdoor antennas/ CATV connected at the same time, since ghosting
and poor reception may result.
11
BEFORE OPERATING YOUR TV SET
2. Consult your dealer or service store for the ANT. MIXER of VHF adaptor.
3. The special converter (decoder) will be supplied by the cable company.
12
HOOK-UP CABLES AND CONNECTORS
HOOK-UP CABLES AND CONNECTORS
Most video /audio connections between components can be made with shielded video
and audio cables that have phono connectors. For best performance, video cables
should use 75-ohm coaxial shielded wire. Cables can be purchased from most stores
that sell audio/video products. Below are illustrations and names of common
connectors.
Before purchasing any cables, be sure of the output and input connector types required
by the various components. Also make sure how long the cables should be.
300-Ohm Twin Lead Connector
This outdoor antenna cable must be connected to an antenna adaptor (300-Ohm to 75Ohm).
Phono Connector
Used on all standard video and audio cables which connect to inputs and outputs
located on the Television's front and rear jack panels.
"F" Type 75-Ohm Coaxial Antenna Connector
For connecting RF signals (antenna or cable TV) to the antenna jack on the television.
S-Video (Super Video) Connector
This connector is used on all camcorders, VCR's and laser disc players with an S-Video
feature in place of the standard video cable to produce a high-quality picture.
TIPS ON REAR PANEL CONNECTIONS
13
LOCATION OF CONTROLS
• The S-Video connection is provided for high performance laser discs, VCR's, etc. that
have this feature. Use this connection in place of the standard video connection if your
device has this feature.
• If your device has only one audio output, connect it to the left audio jack on the TV.
• Refer to the operating guide of your other electronic equipment for additional
information on connecting your hook-up cables.
LOCATION OF CONTROLS
Details are described on the page shown by the number attached to the part name
(example: ).
Front view illustration
NOTE: The front and rear view shows the illustration for the 31DX22B Table Top. The
31KX41K console with VCR storage is not shown bu the controls and terminals are the
same.
Rear view illustration
FRONT PANEL JACKS AND CONNECTIONS
• The front panel jacks are provided as a convenience to allow you to easily connect a
camcorder or VCR as shown in the following examples.
Front panel connections illustration
NOTE:
• Completely insert the connection cord plugs when connecting to front panel jacks. If you
do not, the played back picture may be abnormal.
14
HOW TO SELECT CHANNELS
HOW TO SELECT CHANNELS
TURNING THE SET ON - POWER BUTTON
Push the POWER BUTTON to turn the set ON. (To turn the set OFF, push the POWER
BUTTON again.)
VOLUME CONTROL - VOLUME CONTROL
Push the right side (
: UP ) of the VOLUME BUTTON to make the sound louder, and
the left side (
: DOWN ) of the VOLUME BUTTON to make the sound softer.
Variation of the volume is displayed in the lower part of the screen by the color bar. (Fig.
1)
FUNCTION SELECTION - AVX BUTTON
Every time the AVX BUTTON is pressed, the set alternates between the TV mode and
and AVX mode. To watch the TV, set to the TV mode. At this time, the channel number
is displayed in the upper right of the screen. To enjoy a VCR, set to the VIDEO mode.
See page 12.
CHANNEL SELECTION - CHANNEL BUTTON
Channel selection may be performed by pressing either the CHANNEL BUTTON UP
( ) or DOWN ( ). When pressing the right side ( : UP ) of the CHANNEL BUTTON,
the next higher channel is selected. When pressing the left side (
: DOWN ) of the
CHANNEL BUTTON, the next lower channel is selected. The No. of the channel to
which the TV is tuned is displayed in the upper right of the screen. (Fig. 2)
The channel No. selected is displayed for approx. 8 seconds after changing channels
and disappears automatically.
(When the set is turned ON, the channel No. is displayed on the screen for approx. 15
seconds.)
FRONT INPUT JACKS (for VIDEO:2)
15
HOW TO SELECT CHANNELS
Use these audio/video jacks for a "quick" hook-up from a camcorder or VCR to instantly
view your favorite show or new recording. (Press the AVX button until VIDEO:2 appears
in the top right corner of the TV screen.) See pages 7 and 9.
16
PICTURE CAUTIONS
PICTURE CAUTIONS
When using TV games, computers and similar products with your TV, keep the
CONTRAST and BRIGHTNESS functions at low settings. If a fixed (non-moving)
pattern is left on the screen for long periods of time at a high CONTRAST or
BRIGHTNESS setting, the image can be permanently imprinted onto the screen. These
types of imprints are not covered by your warranty because they are the result of
misuse.
This color television receiver was intended mainly for the private viewing of programs
broadcast by TV stations and cable companies and programs from other video sources.
Public viewing may require prior authorization from the broadcaster or owner of the
video program.
17
THE GENIUS REMOTE CONTROL (CLU-692GR with P-in-P) 31KX41K
THE GENIUS REMOTE CONTROL (CLU-692GR with P-in-P) 31KX41K
In addition to controlling all the functions on your Hitachi Color TV, the new Genius
Remote control is designed to operate different types of VCR's (also abbreviated VTR)
and different types of CATV converters (cable boxes) with one touch. Basic operation
buttons are grouped together in one area. All other controls are separated from them
and arranged in MULTI-PAGE sections, with a display that can be switched to cover
any of the three pages. Functions a re arranged and properly categorized into windows,
making operation simple even when multiple functions are to be controlled.
NOTE: Precoded buttons (
PAGE SELECT SWITCH (
below) will control your Hitachi TV only when the MULTIbelow) is set to "TV" mode.
• To operate your TV, point the Genius remote at the remote sensor of the TV.
• To operate your VCR, point the remote at the remote sensor of the VCR.
• To operate your cable box, point the remote at the remote sensor of the cable box.
CLU-692GR illustration
MULTI-PAGE SELECT SWITCH
Slide the switch in the direction of the arrow to select the MULTI-PAGE mode.
Button layout when "TV" is selected.
Button layout for "VCR." (Power button turns the VCR on or off.)
Button layout for "MENU/CATV." (Power button turns cable box on or off.) See page
15.
TV EXCLUSIVE BUTTONS
These will always control the TV even when the Multi-Page select switch is in the VCR
or MENU/CATV position.
PRECODED BUTTONS
These buttons will control a VCR or a cable box when the Multi-Page select switch is in
the VCR or MENU/CATV position.
LIGHT BUTTON
When you are in a dark room, press this button on to light up the CHANNEL keys,
VOLUME UP and DOWN keys. The light will stay on for about 8 seconds if no button is
pressed. The buttons will not appear to light if the room is too bright.
18
THE GENIUS REMOTE CONTROL (CLU-681GR without P-in-P) 31DX22B
THE GENIUS REMOTE CONTROL (CLU-681GR without P-in-P) 31DX22B
In addition to controlling all the functions on your Hitachi Color TV, the new Genius
Remote control is designed to operate different types of VCR's (also abbreviated VTR)
and different types of CATV converters (cable boxes) with one touch. Basic operation
buttons are grouped together in one area. All other controls are separated from them
and arranged in MULTI-PAGE sections, with a display that can be switched to cover
any of the three pages. Functions a re arranged and properly categorized into windows,
making operation simple even when multiple functions are to be controlled.
NOTE: Precoded buttons (
PAGE SELECT SWITCH (
below) will control your Hitachi TV only when the MULTIbelow) is set to "TV" mode.
• To operate your TV, point the Genius remote at the remote sensor of the TV.
• To operate your VCR, point the remote at the remote sensor of the VCR.
• To operate your cable box, point the remote at the remote sensor of the cable box.
CLU-681GJ illustration
MULTI-PAGE SELECT SWITCH
Slide the switch in the direction of the arrow to select the MULTI-PAGE mode.
Button layout when "TV" is selected.
Button layout for "VCR." (Power button turns the VCR on or off.)
Button layout for "MENU/CATV." (Power button turns cable box on or off.) See page
15.
TV EXCLUSIVE BUTTONS
These will always control the TV even when the Multi-Page select switch is in the VCR
or MENU/CATV position.
PRECODED BUTTONS
These buttons will control a VCR or a cable box when the Multi-Page select switch is in
the VCR or MENU/CATV position.
19
HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR T.V.
HOW TO USE THE GENIUS REMOTE TO CONTROL YOUR T.V.
31KX41K
CLU-692GR
GJ III
31DX22B
CLU-681GR
GJ II
Detailed explanation of the circled numbers on the following pages.
HOW TO USE THE REMOTE TO CONTROL YOUR T.V.
POWER button
Press this button to turn the TV set on or off.
RECALL button
When you want to check the channel being received, or if it has a stereo (ST) or second
audio (SA) program, press the "RECALL" button. You can also check the time, and if
the ON TIME or OFF TIME has been set. (These functions are explained in the MENU SET UP section beginning on page 17.)
If a video input is being used:
20
HOW TO USE THE REMOTE TO CONTROL YOUR T.V.
You can also use the "RECALL" button to quickly clear many of the other on-screen
displays.
MENU, ENTER, CURSOR buttons
All the on-screen display features can be set or adjusted by using these buttons.
The "MENU" button will start or exit the on-screen display.
The "CURSOR" buttons will highlight functions or adjust different features.
The "ENTER" button will set features to your preference.
CHANNEL SELECTOR buttons
Enter two or three numbers to select channels. Enter a "0" first for channels 1 to 9. Use
the "100" button for channels 100 and higher.
Channel selection may also be performed by pressing channel up (
) or down (
)
NOTE: THE TV MAY NOT RECEIVE SOME CHANNELS IF YOU ARE NOT IN THE
CORRECT AIR/CABLE MODE. SEE PAGE 18.
AVX button
The AVX (Auxiliary Video) button will select between the antenna signal and the two
sets of video input jacks each time the button is pressed.
21
HOW TO USE THE REMOTE TO CONTROL YOUR T.V.
VOLUME, MUTE buttons
Press the "VOLUME" up ( ) or down (
level.
) button until you obtain the desired sound
To turn the sound on and off instantly to answer the telephone, etc., press the "MUTE"
button. Press the "MUTE" button again or press the "VOLUME" up ( ) button to restore
the sound.
The word "MUTE" will remain displayed if the CLOSED CAPTION feature is turned off.
The word "MUTE" will not be displayed if the CLOSED CAPTION feature is on.
LAST CHANNEL (LST-CH) button
Use this button to select between the last two channels viewed. (Good for watching two
sporting events, etc.)
PICTURE-IN-PICTURE buttons (Not Available on Model 31DX22B)
See separate section on page 25 for a description.
22
-SET UP- FUNCTIONS
-SET UP- FUNCTIONS
Press MENU, 1, and ENTER to display 3 of the -SET UP- Functions. There are a total
of 8 -SET UP- Functions.
Use the CURSOR UP or DOWN to scroll through the functions, or use the number
buttons to highlight a function. The functions in purple can be selected by pressing
ENTER. To exit the on-screen display, press MENU or RECALL.
NOTE: The MULTI-PAGE SELECT SWITCH must be set to "TV" mode to use the number
keypad. Selecting a function may be easier by using the CURSOR UP and DOWN buttons
with the MENU and ENTER buttons.
To see an autodemonstration of the on-screen display and to practice using the remote
control, press and hold the POWER button on the TV set for approximately 5 seconds.
Press the POWER button on the TV again to end the autodemonstration.
• CLOSED CAPTION
When CLOSED CAPTION is highlighted in purple, press ENTER to see the following
display:
Closed captions are the dialogue, narration, and/or sound effects of a television
program or home video which are displayed on the TV screen. Your local TV program
guide denotes these programs as
.
DISPLAY: ON/OFF is to turn the
display on or off.
MODE: CAPTION is for the program you are viewing.
MODE: TEXT is for additional information such as news reports or a TV program guide.
This information covers the entire screen and viewing the TV program is not possible.
TEXT may not be available with every
program.
CHANNEL 1 is used for the primary language (usually English).
CHANNEL 2 is sometimes used for a second language (may vary by region).
23
-SET UP- FUNCTIONS
Use the CURSOR UP or DOWN to highlight the function to change, press ENTER to
change the function, and press MENU to exit.
NOTE: The word MUTE will not be displayed if the DISPLAY is ON. If you do not have
sound, make sure MUTE is not set.
• INITIAL SETTING
Select -SET UP- and -INITIAL SETTINGS- when setting your TV up for the first time.
Use the CURSOR UP / DOWN or a NUMBER from the remote to highlight the functions
desired.
• AIR / CABLE
Select this function to change between regular VHF/UHF broadcasting (AIR) and cable
(CATV1 or CATV2).
Press the CURSOR buttons to highlight the correct AIR/CABLE mode and press MENU
to exit.
Reception channels for each mode are shown at the
right.
Refer to your cable or TV guide for channel identification standards.
24
-SET UP- FUNCTIONS
If certain CATV channels are poor or not possible in the CATV mode, set the AIR/CABLE- select to CATV2.
• AUTOPROGRAM
This feature will automatically store active TV channels in CHANNEL MEMORY. This
will allow you to skip over unused channels when using the CHANNEL UP ( ) or
DOWN ( ) buttons.
If the MENU button is pressed while the autoprogramming function is engaged,
programming will stop.
See CHANNEL MEMORY to add or erase additional channels.
• CHANNEL MEMORY
Use this function after AUTOPROGRAM to add or erase additional channels to the
remote control CHANNEL ,
buttons.
Add or erase additional channels while still in CHANNEL MEMORY using the
CHANNEL ,
buttons or number buttons and then add or erase using the CURSOR
, buttons.
• CLOCK SET
Use the same remote control buttons as shown in previous examples to display the
clock setting, press MENU, 1, ENTER, 2, ENTER, 4, ENTER.
Once the proper time is set (including AM or PM), press MENU to start.
• CHANNEL CAPTION
Use this feature to give channel names to up to 24 channels for the antenna source
(ABC, PAY1, CMDY, etc.).
25
-SET UP- FUNCTIONS
To display this function, press MENU, 1, ENTER, 3, ENTER.
Press the CURSOR ,
to select letters.
Press the CURSOR , to change position.
Press CHANNEL ,
or the number buttons to select and label additional channels.
Press MENU to exit.
The (*) represents a blank space.
Select CANCEL to erase a CHANNEL CAPTION.
• PROGRAM LIST
This function allows you to view which channels are labeled in CHANNEL CAPTION
(NAME), which have been added to CHANNEL MEMORY (SCAN) and which are
protected by CHILD LOCK (LOCK). Press MENU, 1, ENTER, 4, ENTER to view.
Press the CURSOR
Press MENU to exit.
,
to view more channels.
• TIMER SET
This function will automatically turn the TV on or off.
Press 1, ENTER, to select the ON TIMER.
Press the CURSOR , buttons for TIMER SET: ON or OFF and MODE: 1 SHOT
(one time only) or MODE: DAILY (TV will turn on at the same time every day).
Press the number buttons to select the CHANNEL the TV will tune to when the TV
26
-SET UP- FUNCTIONS
automatically turns on.
Press the CURSOR buttons to set the ON TIME.
Press ENTER after each selection. Your choice will appear in "blocked" letters.
Press MENU to start.
Repeat the previous steps to select and set the OFF TIMER.
Remember to press ENTER after making selections with the CURSOR buttons.
Press MENU to start.
CAUTION: The OFF TIMER is a one time only operation. Do not try to use your TV as a
deterrent when away from home by using both the ON and OFF TIMERS. The OFF TIMER
function will not work until you reset it and the next ON TIME (when using DAILY MODE)
will leave the TV set turned on until you press the power button on the TV or remote control
to turn it off.
• AUTOMATIC MESSAGE
Use this function to set up two personal messages once a day or one time only. Setting
the AUTOMATIC MESSAGE is the same as setting CHANNEL CAPTION and ON
TIMER. Press MENU, 1, ENTER, 6, ENTER to get the AUTOMATIC MESSAGE
display. (You can also use the CURSOR ,
to "scroll" to AUTOMATIC MESSAGE
and then select the function.)
Use the CURSOR
,
Use the CURSOR
,
to select a letter or other character.
to change position.
The asterisk (*) represents a blank space.
When finished with your message press ENTER.
27
-SET UP- FUNCTIONS
Press the CURSOR and ENTER buttons to set the functions shown in the same way as
you set the OFF TIMER.
Press MENU to start.
FIVE beeps will be heard when the AUTOMATIC MESSAGE is displayed.
Examples: Use this message function to remember to take daily vitamins, or use the 1
SHOT to remember to call a friend.
CAUTION: Do not leave an AUTOMATIC MESSAGE on the TV screen for more than 48
hours at a time. A pattern burn may develop and this is not covered by your warranty. The
message can be erased from the TV by pressing RECALL, MUTE, LST-CH, etc.
1
• CHILD LOCK
This function will block out the picture and sound of the selected channel. Press MENU, 1,
ENTER, 7, ENTER to display CHILD LOCK.
The code to set or cancel CHILD LOCK is a three digit key number. The factory preset
key number is 000.
The picture and sound will now be blocked out for this channel. Repeat the same steps
to cancel the CHILD LOCK.
To change the key number, select key number change. Enter the old number (factory
preset 000 for first time use), then enter a new three digit key number you prefer.
If you forget your key number, use the factory code 777 to erase your key number. This
will reset the key number back to the factory preset 000.
28
-SET UP- FUNCTIONS
• VOLUME CORRECTION
Use this function to reduce the volume level of up to four TV channels that sound loud
compared to other TV channels. Press MENU, 1, ENTER, 8, ENTER to display
VOLUME CORRECTION.
Press the CURSOR , to select volume level.
Press ENTER to set the volume level.
Press MENU to exit.
or number buttons while still in VOLUME CORRECTION to set
Use the channel ,
additional channels.
29
PICTURE-IN-PICTURE FUNCTIONS (31KX41K)
PICTURE-IN-PICTURE FUNCTIONS (31KX41K)
P IN P BUTTON
The Picture-in-Picture feature is convenient when you want to watch more than one
program at the same time. You can watch a TV program while viewing a VCR program
(TV or tape) and vice versa with this feature.
P-IN-P BUTTON:
Press the "P in P" button and a sub-picture appears in one corner of the screen. To
remove the sub-picture from the screen, press the button a second time.
EXCHNG BUTTON:
If you wish to switch what is being shown on the main picture to the sub-picture, press
the "EXCHNG" button.
SHIFT BUTTON:
To move the sub-picture to another corner, press the "SHIFT" button. The sub-picture
moves one step counter-clockwise every time the "SHIFT" button is pressed.
30
PICTURE-IN-PICTURE FUNCTIONS (31KX41K)
FREEZE BUTTON:
If you wish to freeze the sub-picture, press the "FREEZE" button. This is convenient
when trying to write down the address for a mail order company, recording statistics for
a sporting event, etc. To return to motion, press the button again.
FREEZE BUTTON WITHOUT A SUB-PICTURE:
Press this button without a sub-picture to freeze the picture you are currently viewing.
Press this button again to return to normal viewing. The other picture-in-picture function
(EXCHNG button) will not work with this FREEZE function.
CAUTION:
A pattern burn may develop if the sub-picture is left in the same corner permanently. If the
P-in-P feature is used frequently, occasionally shift the sub-picture to a different corner.
NOTE:
1. Only sound from the main picture can be heard.
2. When the "P in P" button is pressed, the sub-picture will appear in the same position as
previously set.
3. The "FREEZE" function is released when the "EXCHNG" button is pressed.
4. P in P will not work with a CHILD LOCK channel.
31
-PICTURE- FUNCTIONS
-PICTURE- FUNCTIONS
• PICTURE PROGRAM
PICTURE PROGRAM is for your preferred settings - contrast, color, etc.
You can have two settings, PREFERENCE or use the factory PRESET settings.
Press MENU, 2, ENTER to select the PICTURE PROGRAM functions.
Press the CURSOR buttons to select and make adjustments.
CONTR - Use this function to change the contrast between black and white levels in the
picture.
COLOR - Use this function to adjust the level of color in the picture.
TINT - Use this function to adjust flesh tones so that they appear natural.
BRIGHT - Use this function to adjust overall picture brightness.
SHARP - Use this function to adjust the amount of fine detail in the picture.
WHITE CONTROL: COOL STD (arrow) Use this function to adjust the white balance
(hue) of the picture to your own color preference. When shipped from the factory, this is
set to "cool." If you prefer a reddish screen, set to "STD."
32
-SOUND- FUNCTIONS
-SOUND- FUNCTIONS
Press MENU, 3, ENTER to display the -SOUND- functions.
SOUND PROGRAM is for your preferred settings - balance, bass and treble.
SOUND PROGRAM is used to improve the sound quality.
• SOUND PROGRAM
You can have two sets of settings, PREFERENCE, or use the factory PRESET settings.
Press MENU, 3, ENTER, 1, ENTER to select the SOUND PROGRAM.
Press the CURSOR buttons to select and make adjustments.
BALANCE - This function will control the left, right balance of the TV internal speakers,
the AUDIO TO HI-FI output and the surround speakers.
BASS - This function controls the low frequency audio to all speakers.
TREBLE - This function controls the high frequency audio to all speakers.
• SOUND SETTING
Use the sound settings to improve the sound performance of your TV depending on
listening conditions.
Press MENU, 3, ENTER, 2, ENTER to display the SOUND SETTING.
Use the CURSOR ,
to select a function.
Press ENTER to set a function or to turn it on or off.
• MTS MODE (Multi-Channel Television Sound)
will allow you to select STEREO (a stere broadcast), SA (second audio) program which
33
-SOUND- FUNCTIONS
may be a secondary language, weather report, et., or MONO (monaural sound) used
when receiving a weak stereo broadcast.
The sources received will be displayed below the channel number. Tho source you
select will be displayed to the left of the channel number. See example below for each
selection when both stereo and second audio are received (monaural is always
received).
• LOUDNESS
This function will improve the quality of both low and high frequency sounds when
listening at low volume levels.
• INT. SPEAKERS
This function is useful when first setting up the external speakers, or if you prefer to use
only speakers from a separate stereo system.
• SURROUND
OFF:
Use this for normal stereo/mono broadcasts.
ON:
Listener is surrounded by many sound sources such as a sporting event, etc.
NOTE: Some TV systems do not transmit optimum audio channel separation which can
reduce the effectiveness of the SURROUND function.
34
USING THE GENIUS REMOTE TO CONTROL VCR FUNCTIONS
USING THE GENIUS REMOTE TO CONTROL VCR FUNCTIONS
• To operate your VCR, point the Genius remote at the remote sensor of the VCR.
The Genius remote is designed to operate different types of VCR's. You must first
program the Genius remote to match the remote system of your VCR (Refer to Table 1
on page 32).
(1) Turn ON your VCR.
(2) Set the Multi-page switch on the Genius remote to VCR.
(3) AIM the Genius remote at the front of your VCR.
(4) While holding down the SELECT button, press the button that matches your VCR as
shown on page 32. The channels on the VCR will begin changing after 5 seconds when
the correct button is pressed. When this happens the Genius Remote control is
programmed for your VCR. If the VCR channels do not change after 5 seconds, try a
different Genius Remote button.
(5) Release both buttons when the VCR begins to change channels. The precoded VCR
buttons will now control your VCR.
NOTES:
• If your VCR cannot be operated after performing the above procedure, the codes have not
been precoded into the Genius remote control and it will not be able to operate your VCR.
• You will only have to program your remote control to match your VCR once. The remote
will remember the codes until you replace the batteries.
• Whenever you install or replace batteries in the Genius remote, you must reprogram the
Genius remote to match the remote system of your VCR.
• When operating your TV or a cable box, remember to set the Multi-Page select switch to
the proper position.
• Refer to the instruction manual for the VCR to operate buttons exclusively for the VCR.
• Be sure to keep the original remote control for the VCR even if you use the Hitachi Genius
remote to control your VCR.
35
USING THE GENIUS REMOTE TO CONTROL CABLE BOX FUNCTIONS
USING THE GENIUS REMOTE TO CONTROL CABLE BOX FUNCTIONS
• To operate your cable box, point the Genius remote at the remote sensor of the cable
box.
The Genius remote is designed to operate different types of cable boxes. You must first
program the Genius remote to match the remote system of your cable box (Refer to
Table 2 on page 32).
(1) Turn ON your cable box.
(2) Set the Multi-page switch on the Genius remote to MENU/CATV.
(3) AIM the Genius remote at the front of your cable box.
(4) While holding down the SELECT button, press the button that matches your cable
box as shown on page 32. The channels on the cable box will begin changing after 5
seconds when the correct button is pressed. When this happens the Genius Remote
control is programmed for your cable box. If the cable box channels do not change after
5 seconds, try a different Genius Remote button.
(5) Release both buttons when the cable box begins to change channels. The precoded
cable box buttons will now control your cable box.
NOTES:
• If your cable box cannot be operated after performing the above procedure, the codes
have not been precoded into the Genius remote control and it will not be able to operate
your cable box.
• You will only have to program your remote control to match your cable box once. The
remote will remember the codes until you replace the batteries.
• Whenever you install or replace batteries in the Genius remote, you must reprogram the
Genius remote to match the remote system of your cable box.
• When operating your TV or VCR, remember to set the Multi-Page select switch to the
proper position.
• Be sure to keep the original remote control for the cable box even if you use the Hitachi
Genius remote to control the cable box.
36
USING THE GENIUS REMOTE TO CONTROL CABLE BOX FUNCTIONS
TABLE 1. VCR Precoded remote controls for Hitachi GJ III and GJ II Remote CLU692GR and CLU-681GR
VCR BRAND
Canon
Citizen
Curtis Mathes
Dimensia
GE
Goldstar
Hitachi
Instant Replay
JC Penny
JVC
Kenwood
Magnavox
Marantz
Marta
Memorex
MGA
Minolta
Mitsubishi
Montgomery Ward
NEC
Panasonic
Pentax
Philco
Philips
Pioneer
ProScan
Quasar
RCA
Realistic
Sanyo
Scott
Sears
Sharp
Sony
Sylvania
Tashiko
Technics
Toshiba
Wards
Yamaha
Zenith
Press SELECT and this button
6
0
2/6
2
2/6
0
1
6
1/6/9
0
0
4/6
9
0
6
7
1
7
CHANNEL
9
6
1
4/6
4/6
1
2
6
1/2
6/9/CHANNEL
9
7/8
1/9
CHANNEL
5/VOLUME /VOLUME
4/6
0
6
1/8
CHANNEL
9
3/5
37
EXTERNAL CONNECTIONS
TABLE 2. Cable Box Precoded remote controls for Hitachi GJ III and GJ II Remote
CLU-692GR and CLU-681GR
CATV Brand
Press SELECT and this button
General Instrument
Hamlin
Jerrold
Pioneer
Regal
Scientific Atlantic
Viewstar
Zenith
0/1/2/3/8
4
0/1/2/3/8
7
4
6
9
5
EXTERNAL CONNECTIONS
CONNECTING EXTERNAL AUDIO AMPLIFIER
To control the audio level of an external audio amplifier with the remote transmitter,
connect the system as shown below. (Fig. 1)
NOTE: To prevent damage to the speaker and distorted sound, set the volume control of
the audio amplifier lower and adjust the sound level using the volume control on the remote
transmitter of the TV set.
38
CONNECTING EXTERNAL VIDEO SOURCES
CONNECTING EXTERNAL VIDEO SOURCES
The exact arrangement you use to connect the Video Cassette Recorder, Video Disc
Player and Video Camera to your TV set is dependent on the model and features of
each component. Check the Owner's Manual of each component for the location of its
video and audio inputs and outputs. The following connection diagrams are offered as
suggestions. However, you may need to modify them to accommodate your particular
assortment of components and features. For best performance, video and audio cables
should be made from coaxial shielded wire.
Before Operating External Video Source
The input mode is changed every time the AVX button is pressed as shown below.
Connect External Video source to the INPUT terminal, then press AVX button as
necessary to view the input source.
NOTE: When the TV is set to "VIDEO" and a video signal is not received from VIDEO
INPUT JACK on the back panel of the TV (i.e., VCR/Video Disc Player, etc. is not
connected or the video input device is OFF), the screen will be blank gray or blue in color.
CONNECTING MONAURAL AUDIO VCR or VIDEO DISC PLAYER
Connect the cable from the VIDEO OUT of the VCR or the Video Disc
Player to the INPUT (VIDEO) jack on the TV set. (Fig. 1)
Connect the cable from the AUDIO OUT of the VCR to the INPUT
(MONO)/L (AUDIO) jack. (Fig. 1)
Press the AVX button to view the program from the VCR or the Video Disc
Player. The video mode "VIDEO" disappears automatically after approx. 8 seconds.
Press the AVX button to return to the previous channel.
39
CONNECTING EXTERNAL VIDEO SOURCES
CONNECTING STEREO VCR or STEREO VIDEO DISC PLAYER
Connect the cable from the VIDEO OUT of the VCR or the Video Disc
Player to the "INPUT (VIDEO)" jack on the TV set. (Fig. 1)
Connect the cable from the AUDIO OUT "R" of the VCR or the Video Disc
Player to the "INPUT (AUDIO/R)" jack (Fig. 1).
Connect the cable from the AUDIO OUT "L" of the VCR or the Video Disc
Player to the "INPUT (AUDIO/L)" jack (Fig. 1).
Press the AVX button to view the program from the VCR or Video Disc
Player. The video mode "VIDEO" disappears automatically after approx. 8 seconds.
Press the AVX button to return to the previous channel.
NOTE:
40
CONNECTING EXTERNAL VIDEO SOURCES
• Completely insert the connection cord plugs when connecting to REAR panel jacks. If you
do not, the played back picture may be abnormal.
• If you have an S-VHS VCR, use the S INPUT cable in place of the standard video cable.
41
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT
REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT
TRANSMITTER BATTERY INSTALLATION AND REPLACEMENT
Open the battery cover of the Remote transmitter by pushing the notched part of the
cover with your finger.
a) Push the batteries towards the spring and lift them out.
b) Replace old batteries with two new "AA" size (SUM-3) batteries or equivalent.
c) Match the (+) and (-) marks in the battery compartment.
d) Replace the cover.
CAUTIONS
1. If your television set is to remain unused for a long period of time, for instance, when you
go on a vacation, unplug the television set from the wall outlet.
2. Do not subject the Remote transmitter to shocks such as dropping it on the floor, etc.
Precision parts may be damaged.
3. Do not allow the Remote transmitter to become wet and avoid placing it in areas of high
humidity. Don't leave it on or near a heater. Excess heat or moisture may cause the unit to
cease operation.
4. If the batteries become exhausted, Remote control operation may become erratic or stop
altogether. Replace the old batteries with two fresh "AA" (SUM-3) types.
NOTES
1. When the power button is set to OFF, the OFF TIMER is released.
2. The channel No. indication, volume indication and OFF TIMER indication are not
displayed simultaneously.
3. To operate your TV, point the Remote transmitter at the remote sensor of the TV.
42
ACCESSORIES PART NUMBERS
ACCESSORIES PART NUMBERS
For information regarding how to obtain these accessories, please call TOLL FREE 1800-448-2244 fro your nearest Hitachi Authorized Parts Distributor in the continental
United States. For Alaska and Hawaii, please contact the nearest Hitachi Regional
Office.
Accessories chart illustration
CAUTION: The television stands Model SP313G/SP314G and Model SP350G are
designed for use only with Hitachi TV Model 31DX22B. Use with other television equipment
may result in instability, causing possible injury.
NOTES
1. To operate your TV, be sure to point the Genius Remote at the remote sensor on the
television. To operate other electronic equipment like a VCR, point the remote at the
remote sensor on the device.
2. Refer to the instruction manual of the VCR for operation of the buttons exclusively for the
VCR.
Caution on batteries
• Even if the batteries seem dead, do not remove them until you have replacement batteries
ready to put in. The codes stored in memory will be erased in a few minutes without power.
When replacing batteries, prepare the new ones first.
2 x "AA" size (SUM-3) batteries or equivalent.
43
TROUBLESHOOTING
TROUBLESHOOTING
RECEPTION PROBLEMS (EXTERNAL TO THE TV)
• IGNITION NOISE:
Black spots or horizontal streaks may appear, picture may flutter or drift. Usually
caused by interference from automobile ignition systems, neon lamps, electrical drills
and other electrical appliances.
• GHOSTS:
Ghosts are caused by the television signal following two paths. One is the direct path
and the other is reflected from tall buildings, hills or some other objects. Changing the
direction or position of the antenna may improve reception. Ghosting may also be
caused by defects in the antenna system such as unshielded leads or connecting
several sets to the same antenna without using multiple antenna couplers.
• SNOW:
If your receiver is located in the fringe area of a television station where the signal is
weak, your picture may be marred by the appearance of small dots. When the signal is
extremely weak, it may be necessary to install a special antenna to improve the picture.
• RADIO FREQUENCY INTERFERENCE:
The interference produces moving ripples or diagonal streaks, and in some cases,
causes loss of contrast in the picture.
CHECK HERE BEFORE CALLING FOR SERVICE
44
TROUBLESHOOTING
Troubleshooting chart
45
SPECIFICATIONS
SPECIFICATIONS
Features:
• Super Fine Picture Quality
650 Lines Horizontal Resolution
• Genius Remote
Controls many VCR brands and cable boxes
• P-in-P Functions for 31KX41K
• Full Function Menu On-Screen Display
• Full Set of Input Jacks, including S-Video
• Closed Caption Decoder
• VCR storage on 31KX41K
Inputs:
• Power input....................................AC 120V, 60Hz
• Power Consumption.......................116W
• Power Consumption (maximum).....155W
• Antennal input impedance...............75 Ohm
• Channel coverage...........................181 ch.
VHF Band......................................2~13
UHF Band......................................14~69
CATV Mid Band............................A-5~A-1, A-I
Super Band.....................................J-W
Hyper Band....................................W+1-W+28
Ultra Band......................................W+29-W+84
• Video............................................1.0Vp-p, 75 Ohm
• S-Video
Luminance (Y)...............................1.0Vp-p, 75 Ohm
Chrominance (C)...........................0.286Vp-p, 75 Ohm
• Audio input impedance..................47 kOhm
Average input level........................470mVrms
Maximum input level......................940mVrms
Outputs:
• Video...........................................1.0Vp-p, 75 Ohm
• Audio (fixed)................................470mVrms, 1 kOhm
31DX22B
• Height (in.) 26 3/8
• Width (in.) 30 23/32
• Depth (in.) 22
• Weight (lbs.)
128
31KX41K
44 7/8
32 3/8
22 31/64
230
NOTE: Due to improvements, specifications in this operating guide are subject to change
without notice.
46
HITACHI SERVICE HOTLINE
HITACHI SERVICE HOTLINE
To locate an authorized HITACHI service facility in the continental U.S.A.
DIAL TOLL FREE
7 days a week, 24 hours a day
800 HITACHI
1-800-448-2244
Hitachi Home Electronics (America), Inc.
Hitachi has made every effort to assure you hours of trouble free operation from your
unit. However, should you require service, a network of Hitachi Authorized Service
Facilities has been established in all 50 states and Puerto Rico. Each facility will
provide you with convenient and expedient assistance. Our service "Hotline" operator
will direct you to the Hitachi Authorized Service Facility nearest you. Just present proof
of purchase and/or delivery receipts to the Hitachi Authorized Service Facility, and
service will be rendered in accordance with the terms of the limited warranty as stated
on your warranty card or operating guide.
Should you have any questions regarding in-warranty service, operation or
technical assistance, please contact:
Hitachi Home Electronics (America), Inc
3890 Steve Reynolds Blvd
Norcross, GA 30093
Tel: 404-279-5600
Hitachi Sales Corporation of Hawaii
3219 Koapaka St.
Honolulu, HI 96819
Tel: 808-836-3621
47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement