Hitachi 42PD580DTA Flat Panel Television User Manual

Hitachi 42PD580DTA Flat Panel Television User Manual
Color Plasma Display
Model
42PD580DTA
READ THE INSTRUCTIONS INSIDE CAREFULLY.
KEEP THIS USER'S MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your Plasma TV.
SERIAL NO.
The serial number is located on the rear of the Plasma TV.
USER'S MANUAL
NOTE:
The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for
any errors that may appear in this manual.
TRADEMARK ACKNOWLEDGEMENT
VGA and XGA are registered trademarks of International Business Machines Corporation.
APPLE and Macintosh are registered trademarks of Apple Computer, Inc.
VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.
All brand or product names are trademarks or registered trademarks of their respective holders.
E030039027
Printed in Thailand
USER'S MANUAL
Thank you very much for purchasing the HITACHI PDP TV.
Before using your TV, please carefully read the "SAFETY
INSTRUCTIONS" and this "USER'S MANUAL" so you will
know how to operate the PDP TV properly. Keep this
manual in a safe place. You will find it useful in the future.
Notes on Installation Work:
This product is marketed assuming that it is installed by
qualified personnel with enough skill and competence.
Always have an installation specialist or your dealer install
and set up the product. HITACHI cannot assume liabilities
for damage caused by mistake in installation or mounting,
misuse, modification or a natural disaster.
Note for Dealers:
After installation, be sure to deliver this manual to the
customer and explain to the customer how to handle the
product.
1
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
Follow all warnings and instructions marked on this television.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use the attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. Televisions are designed to comply with the recommended
safety standards for tilt and stability.
Do not apply excessive pulling force to the front, or top, of
the cabinet which could cause the product to overturn
resulting in product damage and/or personal injury.
16. Follow instructions for wall, shelf or ceiling mounting as
recommended by the manufacturer.
17. An outdoor antenna should not be located in the vicinity of
overhead power lines or other electrical circuits.
18. Under no circumstances remove the rear cover of your PDP
TV.
Never guess or take any chances with electrical equipment
of any kind - it is better to be safe than sorry!
19. After the PDP TV has been on for any length of time, you will
notice that the screen becomes warm. Please note that this
is normal.
Sometimes the screen might have some tiny bright or dark
spots. Please note that this is normal.
20. To prevent scratches or damages to the Plasma screen, do
not knock or rub the surface with sharp or hard objects.
Clean the screen with a soft cloth moistened with warm
water and dry with a soft cloth. A mild soap may be used if
the screen is extremely dirty. Do not use harsh or abrasive
cleaners!
21. Use a soft cloth to clean the cabinet and control panel of the
PDP TV. When excessively soiled dilute a neutral detergent
in water, wet and wring out the soft cloth and afterward wipe
with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent,
abrasive cleaner, powder soap, OA cleaner, car wax, glass
cleaner, etc. especially because they would cause
discoloration, scratches or cracks.
This product contains lead. Dispose of this product in accordance with applicable environmental laws. For product recycling and
disposal information, contact you local government agency.
Do not place any objects on the top of the television which may fall or cause a child to climb to retrieve the objects.
PREVENTION OF SCREEN BURN
Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed
(nonmoving) patterns can cause permanent damage to television receivers. Such “SCREEN BURNS” constitute misuse and are
NOT COVERED by your HITACHI Factory Warranty.
PUBLIC VIEWING OF COPYRIGHTED MATERIAL
Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require
prior authorization from the broadcaster or owner of the video program material.
2
FEATURES
Large-screen, high-definition plasma display panel
The 42-inch color plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, creates a high-definition,
large-screen (aspect ratio : 16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic
sources and ambient power lines, the panel produces high-quality display images free from color misconvergence and
display distortion.
High Performance Digital Processor
A wide range of input signals can be handled, including composite, component, and HDMI.
High Definition Digital Processor creates the fine-textured image with dynamic contrast.
In addition, it corresponds to a broad array of personal computer signals, from 640 x 400 and 640 x 480 VGA to 1280 x
1024 XGA.(PC RGB Input)
Easy-to-use remote control and on screen display system
The remote control included eases the work of setting display controls. Further, the on-screen display system, displays the
status of signal reception and display control settings in an easy-to-view fashion.
Power saving system
The power saver feature saves power consumption automatically when input signals are not available. When connected to a
VESA DPMS-compliant PC, the PDP TV cuts its power consumption while it is idle.
Connecting to an Audio Visual Device
• One S-Video terminal, one composite terminal, one component terminals, a HDMI terminal and a PC RGB input terminal
have been added.
• A video output terminal is also provided as a monitoring output.
• A wide range of devices can also be connected besides personal computers.
Options
TV stand or wall mount
3
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS …………2
FEATURES .....................................................3
SAFETY INSTRUCTIONS ...............................5
IMAGE RETENTION OF PLASMA DISPLAY ..9
COMPONENT NAMES.....................................10
Main Unit ...............................................................................10
Remote control ....................................................................11
OTHER FUNCTIONS .....................................43
Audio Switching ...................................................................43
Signal Check .....................................................................44
Power Save Mode.................................................................45
TROUBLESHOOTING ....................................46
Symptoms That Seemingly Appear to be Failures .............46
Actions to Correct Abnormal Displays .................................48
Loading Batteries ..............................................................11
PRODUCT SPECIFICATIONS ........................49
Handling the Remote Control............................................11
Recommended Signal List ...................................................50
Function Buttons.........................................................12
INSTALLATION INSTRUCTIONS ................19
Installation.............................................................................19
Connecting to an Audio Visual Device..............................20
Connecting to a PC..............................................................24
Power Cord Connection .......................................................25
OPERATING INSTRUCTIONS.......................26
Turning Power On and Off ..................................................26
Input Switching ....................................................................27
Volume Adjustment .............................................................27
Audio Mute ..........................................................................27
Input Signal Screen Display ................................................28
Using the Menu Screen (On-screen display system) ........29
Video Menu...........................................................................30
Image Menu.........................................................................31
Audio Menu ..........................................................................32
Language Menu...................................................................32
System Menu.......................................................................33
Using the HDTV Menu Screen.........................................36
Edit Channel...........................................................................37
Parental Guidance....................................................................38
Installation..........................................................................39
General Setting...................................................................41
System.............................................................................42
Notes about This Manual
• The information in this manual is subject to change without notice.
• While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us
should you have any comments, views or questions about our product.
• Fully understand the prerequisites to using the product, such as hardware and software specifications and
constraints, in using the product. We are not held liable for damages caused by improper handling of the product.
• Reproduction of this manual in whole or in part without our prior written permission is prohibited.
• The product names mentioned in this manual may be trademarks or registered trademarks of their respective
owners.
4
SAFETY INSTRUCTIONS
This PDP TV has been designed and manufactured to meet international safety standards, but like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and
follow all the instructions.
About the Symbols
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent
danger to the user and others, and to prevent property damage. The meanings of these symbols are described below. It is
important that you read these descriptions thoroughly and fully understand the contents.
This symbol indicates information that, if ignored, could possibly result in personal injury or even
death due to incorrect handling.
This symbol indicates information that, if ignored, could result possibly in personal injury or
physical damage due to incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or nearby (the
symbol to the left indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or nearby (the
symbol to the left indicates that the power plug should be disconnected from the power outlet)
WARNING
Never use the PDP TV if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements,
cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making
sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be
dangerous.
Do not insert liquids or foreign objects.
Disconnect
the plug
from the
power outlet.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where
children are present.
If liquids or foreign objects should enter the television, immediately turn off the power switch, disconnect the power plug from
the power outlet and contact your dealer.
• Do not place the television in a bathroom.
• Do not expose the television to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the television.
• Do not place metals, combustibles, etc on or around the television.
Never disassemble or modify the PDP TV.
The television contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not give the PDP TV any shock or impact.
Do not
disassemble.
If the television should be shocked and/or broken, it could result in an injury, and continued use could result in fire or
electrical shock. If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug
from the power outlet and contact your dealer.
Do not place the PDP TV on an unstable surface.
If the television should be dropped and/or broken, it could result in an injury, and continued use could result in fire or
electrical shock.
• Do not place the television on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the PDP TV.
If the ventilation is obstructed during the operation of the television or just after switching off the power, it could result in
damage and shorten the lifespan of your television due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the television and other objects such as walls.
• Do not place anything around ventilation openings of the television.
• Never block ventilation openings.
• Do not put the PDP panel side up.
• Do not cover the television with a tablecloth, etc.
• Do not place the television on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication
on the television and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
5
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry
cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to
extend the lead, obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of
the same value, type and approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this television with the ground terminal provided at the power outlet
using the enclosed power cord. If the provided plug does not fit your outlet, consult an electrician for
replacement of the obsolete outlet.
Be careful in handling the power cord and external connection cables.
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too
much heat, pressure or tension to the power cord and cables.
If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the television or heavy objects on the power cord and cables. Also, do not place a spread, cover,
etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power
cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it
with your hand holding the plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the
point where they exit from the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled
properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency
treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this television.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres
your body or clothes, rinse well with water.
• Obey the local laws on disposing the battery.
6
Surely connect
the ground wire.
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
CAUTION
Be careful in moving the PDP TV
Neglect could result in an injury or damage.
• Do not move the television during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the television with two persons.
• Avoid any impact or shock to the television; particularly take care of glass screen.
Do not put anything on top of the PDP TV.
Placing anything on the television could result in loss of balance or falling, and cause an injury or damage. Use special
caution in households where children are present.
Avoid a humid or dusty place.
Placing the television in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical
shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the television and other parts, and could result in transformation, melting or
fire.
• Do not place the television, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the television in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the television is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the television. Neglect could result in fire or electrical shock.
PRECAUTIONS
Disconnect the
plug from the
power outlet.
Installation environment
Do not obstruct a ventilation hole.
Do not put the television on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the
television. Do not put the television in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
How to view the PDP TV
If you use the television in too dark a room, your eyes may become tired. Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue. Your eyes will get fatigued after viewing the television for
long period of time. Relax your eyes by viewing away from the television from time to time.
Please watch the television in downward direction.
Note on image retention
The plasma PDP TV illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of
illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the
screen as grayed-out images.
Tips to prevent such image retention are:
• Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and
graphic patterns, for long.
• Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them
using screen saver function.
• Turn down the contrast and brightness controls.
How to clean the plasma screen panel of the PDP TV
Before cleaning the television, turn off the television and disconnect the power plug from the power outlet.
To prevent scratching or damaging the PDP screen face, do not knock or rub the surface with sharp or hard objects. Clean the
screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent.
Do not use harsh or abrasive cleaners.
How to clean the cabinet of the PDP TV
Use a soft cloth to clean the cabinet and control panel of the television. When excessively soiled dilute a neutral detergent in water,
wet and wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc.
especially because they would cause discoloration, scratches or cracks.
7
SAFETY INSTRUCTIONS (continued)
About the Symbols (continued)
Prevention of an obstacle to Radio receivers
This television has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio
receivers.
• Keep the television away from Radio.
• Adjust Radio antennas in order for the television not to receive interference.
• The antenna cable of Radio should be kept away from the television.
• Use a coaxial cable for antenna.
You can check if this television influences Radio receivers by turning off all other equipment other than the television. If you
find a problem receiving Radio when using the television, check the instructions mentioned above.
Precautions for the cable connection
• Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of
equipment), are properly made and in accordance with the manufacturers instructions. Switch off and withdraw the
power plug before making or changing connections.
• Confirm the connector is fixed tightly when the signal cable is connected. Also confirm the screws on the connector are
tightened.
• Plug the power cord of the television into a different socket from that for other equipment, such as Radio etc.
• Use a plug with ground terminal and make sure that it connects to the ground.
Precaution during transportation
Please pay attention when you transport this television because it is heavy.
Furthermore, use the original carton box and its packaging materials when the television is transported. Failure to transport
the television in any carton except the original carton may result in damage to the television. Save the original carton box
and all packing material.
Do not physically impact the remote control.
A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote
control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the television.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
Precautions for the installation
• Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the
manufacturers approved stand or legs with the fixings provided according to the instructions.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive
pulling force to the front, or top, of the cabinet that could cause the product to overturn resulting in product damage
and/or personal injury.
• Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
• Only use the attachments/accessories specified by the manufacturer.
• Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
Other precautions
• Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended
operation or has a stand-by mode. Switch off using the switch on the equipment and show your family how to do this.
Make special arrangements for infirm or handicapped people.
• Disposal of this product may require specific instructions pertaining to your resident region.
• Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
8
IMAGE RETENTION OF PLASMA DISPLAY
There are different characteristics that result in panel image retention depending on how the plasma display is
used. Situations and effective usage methods related to ghosting are provided below.
Image retention characteristics of a plasma display
The image retention phenomenon of a plasma panel occurs due to partial phosphor degradation arising from partial character and
figure display.
For example, when the character image as shown in Fig. A at the
right is continuously displayed for a long period of time, the only
part of the phosphor (Red, Green, Blue) that will degrade will be
the color of the applicable character display portion.
Consequently, when a white image is displayed on the entire
screen as shown in Fig. a, the character marks displayed up to
that time will become a color difference visible to the eye, but the
phosphor will never burn.
[Fig. A]
[Fig. a]
■ The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.
• The tendency of the phosphor is to degrade more the
brighter the characters and figures are displayed. When
images of figures with different levels of brightness, as
shown in Fig. B, are continuously displayed for a long
period of time, it becomes easier for image marks at
locations when the brighter figures are displayed to be
noticeable.
[Fig. B]
[Fig. b]
* The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image
retention is seen differs depending on the operation time and brightness.
Methods to Reduce the Occurrence of Image Retention
• Lower the Contrast and Brightness settings of the plasma display as much as possible.
A function is provided in the display that controls the brightness of the screen to reduce degradation of the panel. Using this function
makes it possible to reduce image retention.
• Set the PDP TV to a “Move Screen” display.
Move Screen function works to reduce image retention when displaying images on the four corners, such as TV station logos and
clock display.
(Settings can be made using Move Screen from Function MENU shown on 33 .)
• Using in combination with moving images
Since the degradation of the fluorescent material progresses comparatively uniform for moving images, the occurrence of partial
image retention can be controlled. We recommend to use in combination with moving images such as a DVD.
* Please be careful since image retention will occur if display is left in PIP display state for a long period of time.
* Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image
are cut and broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention
in these portions can be expected to occur, so please be aware.
Notes
About screen defects
• High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and
bright spots (points that are too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed, but
these will disappear and return to normalcy. This is not a malfunction.
About the panel screen
• Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel
surface may rise in some cases. Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over
the panel surface but avoid strong impact because there is still danger of glass breakage.
9
COMPONENT NAMES
Main Unit
Front
Control panel
• Adjustment buttons are
located on the bottom.
• The front bezel is provided
with indications to distinguish
the adjustment buttons.
Indicating lamp 26
Remote-control 11
receiver
Main power switch
26
①
②
③
④
⑤
⑥
⑦
POWER
PROGRAMS/UPS
PROGRAMT/DOWNT
VOLUMEX/RIGHTX
VOLUMEW/LEFTW
INPUT/EXIT
MENU/ENTER
• Normal button action/Button action when MENU engaged
• The main power switch is located at the back, on
the right side.
Rear
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two people
are required to transport it safely.
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Main power switch
26
Power cord
External device connection terminals
* Input terminals from
10
20
to
24.
COMPONENT NAMES (continued)
Remote control
Loading Batteries
Handling the Remote Control
1. Open the battery cover of the remote control by pressing the
notched part of the cover with your fingers and pulling the
cover off.
2. Insert two new “AAA” size batteries for the remote control.
When replacing old batteries, push them towards the springs
and lift them out.
3. Match the batteries to the (+) and (-) marks in the battery
compartment.
4. Replace the cover.
BOTTOM VIEW
Use the remote control within about 5 m from front of the unit’s
remote control sensor and within 30 degrees on both sides.
(Remote Control)
Press and pull the back cover to
remove
ATTENTION
• Do not use new and old batteries together. The batteries
could explode or leak, resulting in fires, physical injury, or
stains.
• When loading batteries, observe their correct polarities as
marked on the product. If loaded in the wrong direction, the
batteries could explode or leak, resulting in fires, physical
injury, or stains.
• Do not drop or impact the remote control.
• Do not splash the remote control with water or put it on a wet
object to avoid possible failures.
• Before leaving the remote control out of use for an extended
period of time, remove the batteries from it.
• If the remote control begins to lack responsiveness, replace
the batteries.
• Strong light such as direct sunlight impinging on the
photoreceptor of the remote control can cause operational
failure. Position this unit to avoid direct contact with such
light.
11
COMPONENT NAMES (continued)
Remote control (continued)
Function Buttons
NOTE
ZOOM+ & ZOOM- buttons:
This function not support.
1. POWER button
Press this button to turn the TV set on or standby.
2. I/II button
Press to select sound mode: Mono▼ Stereo
12
, Language A[I], Language B[II].
COMPONENT NAMES (continued)
Remote control (continued)
3.
(MUTE) button
Press to mute the volume. Press again to restore the volume.
4. RECALL button
Press to display source input signal on the display. When the PIP function is working, press to display audio source.
Then press ▲ ▼ buttons to select between the sound of your main picture or PIP.
5. PC/HDMI button
Press to switch directly to PC and HDMI mode. Press repeatedly to circle through the selections.
6. VIDEO button
Shortcut to access the Composite Video, S-Video, and Component mode. Press repeatedly to circle through the
selections.
7. NUMBER buttons
Use Number buttons with --/--- button to choose specific channel.
8. RTN (RETURN) button
Press this button to toggle between the current and last channel viewed and press jump back to last page of OSD.
9. --/--- button
Press this button to choose specific number channel for three code upper channel.
10. EXIT button
This button will exit all On-Screen Displays.
11. MENU button
The MENU button will start the OSD.
12. ▲▼W X buttons
Press Up/Down/Left/Right buttons to adjust the options under OSD menu.
13. ENTER button
Press ENTER button to select the functions under OSD menu.
14. CHANNEL POSITION+/- buttons
Press Channel +/ Channel - buttons to change channels under TV mode.
15. VOLUME+/- buttons
Press Vol+ / Vol- buttons to increase and decrease the volume.
16. SORT button
Press to access the TV channel list table.
17. SORT EDIT button
Press SORT EDIT button to enter function menu for editing, channel name, Insert, and delete the channel from list
table.
18. P. MODE button
Press to select Natural, Cinema and Dynamic picture mode. Press repeatedly to circle through the selections.
13
COMPONENT NAMES (continued)
Remote control (continued)
19. P. SIZE button
Press repeatedly to change image to different size. Sizes include Full, 4:3 Standard, Panoramic, 4:3 Zoom and 16:9
zoom.
4:3 Standard
Use this side mode to display conventional (4:3) images. Side panels (gray areas) are placed to
the left and right of the image to preserve the original aspect ratio of the source. Note: Use this
mode for only 15% of your total viewing time to prevent uneven aging of the phosphors.
Phosphors in the lighted area of the picture will age more rapidly than the gray areas.
16:9 Zoom
Use this side mode to display conventional (4:3) sources by linearly increasing image expansion
from the center towards the edges of the display area in order to fill it.
4:3 Zoom
Use these side modes to zoom in on conventional (4:3) sources.
Full
Use this side mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 side
ratio.
Panoramic
Use this side to Zoom-in once while in 16:9 side.
Depending on the input signal format received, the picture format ratio allows you to adjust the images through the
following options.
(1) TV/Composite/S-Video/Component(480i/480p/576i/576p) Input
Input
Full
4:3 Standard
16:9 Zoom
4:3 Zoom
Panoramic
(2) Component(720p/1080i)/HDMI Input
Input
Full
(3) RGB Input
Auto adjust to full size. (Aspect ratio is not changeable.)
ATTENTION
Using a wide picture size.
• This TV has a picture size selection feature. If an incompatible size is selected to play certain software, such as a TV program, the
image would appear different from original. Take this into consideration when making picture size choices.
• Use of this TV in its enlarged display mode with the wide feature enabled in coffee shops and other establishments for commercial
or public viewing purposes could infringe on the copyright holders right protected by Copyright Law.
• When a normal 4:3 image is displayed over the entire picture in the Panoramic mode, parts of the periphery of the image may
disappear and appear distorted in some cases. Use the 4:3 mode to view image, which were created in 4:3 mode.
20. ZOOM +/- buttons
This function not support.
21. PIP SWAP button
Press to exchange the main video signal source with PIP video signal source.
14
COMPONENT NAMES (continued)
Remote control (continued)
22. PIP INPUT button
Activate PIP by pressing PIP Input button to select desired video input. To turn off PIP by keep pressing PIP Input
button until the PIP window disappear. PIP source cannot be the same with main video source. (Component YCBCR
/YPBPR, HDMI and PC RGB are not accessible to PIP) / (HDMI 480i / 576i cannot support PIP function.)
Main
Sub
TV
TV
HDTV
Composite
S-Video
Component
HDMI
PC RGB
○
○
○
○
○
×
○
○
○
○
×
○
○
○
×
○
○
×
×
×
HDTV
○
Composite
○
○
S-Video
○
○
○
Component
×
×
×
×
HDMI
×
×
×
×
×
PC RGB
×
×
×
×
×
×
×
NOTE
For changing TV channel under PIP function, Press directly channel+/-, number and return buttons on remote control to change
the channel.
23. SLEEP button
Press the sleep button repeatedly to set the sleep timer to 30, 60, 90, and 120 minutes
15
COMPONENT NAMES (continued)
Remote control (continued)
Teletext Function Buttons
A. TV/TEXT button
Press to switches between the TV mode and the Teletext mode.
B. BLUE button
Press to operate the Teletext function in Teletext pattern. (Function depends on the Teletext pattern.)
C. YELLOW button
Press to operate the Teletext function in Teletext pattern. (Function depends on the Teletext pattern.)
D. GREEN button
Press to operate the Teletext function in Teletext pattern. (Function depends on the Teletext pattern.)
E. RED button
Press to operate the Teletext function in Teletext pattern. (Function depends on the Teletext pattern.)
F. REVEAL button
Press this allows hidden information (found on some Teletext pages) to be displayed on the screen.
G. SUB PAGE button
Use this to activate sub page mode directly in Teletext service.
H. CANCEL button
This allows the screen to return to the TV mode temporarily while searching for a required text page. When the required
text page has been received, the page number will be displayed at the top left of the screen. Press the CANCEL button
again to display the Teletext screen.
I. INDEX button
Press this button to select the index page that displays the list of Teletext contents.
NOTE
• Certain pages do not show linked pages at the bottom of the screen. To display linked pages, press the INDEX button.
• Refer to Teletext Language shown on 34 .
16
COMPONENT NAMES (continued)
Remote control (continued)
HDTV Function Buttons
a. INFO button
Switch between Viewing mode, Channel Banner, and Channel Banner with Extended Info.
b. DTT/TV button
Press to switches between HDTV mode and TV mode.
c. DTT MENU button
Press to access HDTV OSD menu for features adjustment.
d. BLUE button
Press to operate the HDTV function in HDTV OSD. (Function depends on the HDTV OSD.)
e. YELLOW button
Press to operate the HDTV function in HDTV OSD. (Function depends on the HDTV OSD.)
f. GREEN button
Press to operate the HDTV function in HDTV OSD. (Function depends on the HDTV OSD.)
g. RED button
Press to operate the HDTV function in HDTV OSD. (Function depends on the HDTV OSD.)
h. FAV CHANNEL button
Press to switch directly to your favorite channel.
17
COMPONENT NAMES (continued)
Remote control (continued)
i. CANCEL LIST button
Use this to switch directly to your HDTV channel list.
j. GUIDE button
Use this to switch directly to HDTV guide.
18
INSTALLATION INSTRUCTIONS
Installation
• If you have purchased the model without the stand attached:
When installing the monitor, use the optional stand CMPAD42T.
The desktop stand has been used for the installation in this manual.
• Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can
cause overturning or dropping and result in fire, electrical shock or injury. Please note that our company assumes
absolutely no responsibility for personal injuries or property damage caused by use of other mount units or
improper installation.
• Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible.
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches: For a desktop set-up) or
more between the sides and other objects such as walls, etc., so that the ventilation holes are not blocked.(*)
• Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
10cm (4 inches) or more*
Cord or chain
Wall or pillar
Clamp
Hook
Cord or chain
PRECAUTIONS
Please avoid installing the TV directly on the wooden floor. Depending on the quality and condition of the floor, the
desktop stand may stick to the floor face, and the surface could come off when the TV is lifted up.
Read SAFETY INSTRUCTIONS (
these steps:
5
to
8
) carefully to ensure maximum safety before proceeding to
• Choose an appropriate site and install the product on a level table where the stand is secure.
• Install the PDP TV to have ready access to a power socket available.
• Make sure that the power switch of this device is turned off.
19
INSTALLATION INSTRUCTIONS (continued)
Connecting to an Audio Visual Device
(1) Make sure that the signal of the audio visual device to be used is compatible with the specifications of this
device. See “PRODUCT SPECIFICATIONS” concerning the specifications of this device. 49 ~ 51
(2) Make sure that the power switch of the PDP TV is turned off.
(3) Make sure that the power switch of the audio visual device is turned off.
(4) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of
this device and the signal output terminal of the audio visual device.
CONNECTING AN DIGITAL TV ANTENNA
1. Attach a DVB-T antenna cable to the DVB-T terminal.
2. Connect the outdoor antenna cable lead-in to the terminal marked DVB-T
IN on the rear of the TV set.
3. Connect all power sources before activating the PDP TV.
4. Turn on the PDP TV.
5. Press DTT/TV on the remote to choose HDTV mode.
6. When operating the HDTV at first time, please execute “Installation”
menu 39 for normally display.
CONNECTING AN ANALOG TV CABLE OR AN ANALOG ANTENNA WITHOUT A TV CABLE BOX
1. Use an antenna cable connects to an outdoor antenna.
2. Connect all power sources before activating the PDP TV.
3. Turn on the PDP TV.
4. To use the TV, press DTT/TV button on the remote to choose TV mode.
5. When operating the TV at first time, its TV system is at “default
factory mode” and this mode cannot display the image normally
on the screen. In order to watch the TV program without problem,
please execute “TV Channel Setup” menu 33 for normally display.
Precautions when connecting the antenna
‧ Please use a coaxial cable which is free from interference to connect the antenna.
‧ Avoid using a parallel flat feeder wire as interference may occur, causing reception to be unstable and stripe noise to
appear on the screen.
‧ Avoid using indoor antenna as this may be affected by interference. Please use CATV net or outdoor antenna.
‧ Keep the power cord as far away from the antenna wire as possible.
‧ For safety, install an external antenna conforming to AS1417.1(applicable for Australia only)
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not provided) for RF
LEADS to reduce the noise
20
INSTALLATION INSTRUCTIONS (continued)
Connecting to an Audio Visual Device (continued)
CONNECTING HDTV SOURCES
HDTV input sources, such as a digital cable box, digital satellite receiver, or digital terrestrial receiver box, can be connected as desired,
using the appropriate cable system.
1. Connect the HDTV source device using the appropriate cable pair, in the following order of preference:
HDMI cable or Component cable and audio cable
2. Connect all power sources before activating the PDP TV.
3. Turn on the PDP TV.
4. Press the button corresponding to the appropriate signal source (HDMI, or Component Video-YCBCR/YPBPR)
CONNECTING A TV CABLE BOX OR SATELLITE RECEIVER
1. Connect the TV Cable Box or Satellite Receiver device using:
Component cable and Audio cable or S-Video cable and Audio cable or Composite cable and Audio cable.
2. Connect all power sources before activating the PDP TV.
3. Turn on the PDP TV.
4. Press the button corresponding to the appropriate signal source (Component Video, YCBCR/YPBPR, S-Video or Composite Video)
21
INSTALLATION INSTRUCTIONS (continued)
Connecting to an Audio Visual Device (continued)
CONNECTING A DVD PLAYER
1. Connect the DVD player using:
HDMI cable or Component cable and Audio cable or S-Video cable and Audio cable or Composite cable and Audio cable.
2. Connect all power sources before activating the PDP TV.
3. Turn on the PDP TV.
4. Press the button corresponding to the appropriate signal source (HDMI, Component Video, YCBCR/YPBPR, S-Video or Composite
Video)
CONNECTING A AUDIO RECEIVER
For improved sound quality, you may want to play the audio of the PDP through your stereo system.
1. Use an audio cable and Subwoofer cable to connect the PDP’s audio output jacks to the line input jacks on the A/V receiver.
2. Connect all power sources before activating the PDP TV.
3. Turn on the PDP TV.
4. Press the MENU to display the menu, then press ▲ ▼ to select Audio.
5. Press Enter, then press ▲ ▼ to select subwoofer and press W X to select On/Off.
22
INSTALLATION INSTRUCTIONS (continued)
Connecting to an Audio Visual Device (continued)
NOTES:
• If the Video OUTPUT (Monitor) terminal is connected to an external monitor with a 75 Ohm terminal, it is possible to
view the same image as on the main unit. But it is possible to monitor only the TV signal, Composite Video signal or
the S-Video signal that is displayed on the screen at the time.
• If a Video equipment with an S-Video output terminal is used, cabling by the S-Video cable is recommended to provide
finer Video quality.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
• HDMI (High-Definition Multimedia Interface) is a digital interface based on DVI (Digital Visual Interface), which is an
added function for audio visual equipment.
– It does not have degradation by transmission since it is digital.
– With only one cable, it is possible to transmit both picture signals and audio signals.
• In case of using analog audio, when connecting with DVI-HDMI transformation connector, use analog RGB audio
terminal for input.
23
I
INSTALLATION INSTRUCTIONS (continued)
Connecting to a PC
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of
this device. See "PRODUCT SPECIFICATIONS" concerning the specifications of this device 49 ~ 51 .
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (PC RGB INPUT) on the rear panel of this device to the display signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the
adapter provided with the personal computer may be necessary in some cases. For details, refer to the instruction
manual of the personal computer or ask the personal computer manufacturer or your local retail dealer.
CONNECTING PC
1. Connect the PC using:
D-Sub cable and ⌀ 3.5 mm Audio cable
2. Connect all power sources before activating the PDP TV.
3. Turn on the PDP TV.
4. Press the button corresponding to the appropriate signal source (PC RGB)
NOTE
• This PDP TV can automatically defect and display the signal format. Please refer to “Recommended Signal List” on
51
24
INSTALLATION INSTRUCTIONS (continued)
Power Cord Connection
Connect the power cord, after completing all other device connections.
①
②
③
① Connect the power cord to this device.
② Use the binders to fix the power cord.
③ Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
• Use only the power cord provided. (Ask your local retail dealer about the power cord for TV monitor)
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric
shock.
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to
clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the
lead, obtain an appropriate extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same
value, type and approval as the original. Ensure the fuse cover is returned to its origin position.
25
OPERATING INSTRUCTIONS
Indicating Lamp
Remote-control receiver
Main power switch
Turning Power On and Off
• To turn the PDP TV power ON, press the main
power switch on the PDP TV main unit to ON, and
then press the POWER button of control panel or
the POWER button on the remote control.
• To turn the TV power OFF, press the POWER
button of control panel or the POWER button on
the remote control, and then press the main power
switch on the PDP TV main unit to OFF.
• During normal use, the main power switch is set in the
ON position, and the monitor can then be turned
ON/OFF using the POWER button or the POWER
button on the remote control.
• The main power switch is located at the back, on the
right side.
Indicating lamp
Indicating Lamp
Off
Lights Red
Lights Orange
Power button
Lights Green
Power Status
Operating
When the main power
Off
switch is set to OFF.
When the main power
Off
switch is ON, and the
(Stand-by)
POWER button is OFF.
When the main power
Off
switch is ON, and the
(Power Save)
power button is ON.
When the main power
switch is ON, and the
On
power button is ON.
POWER button
When the indicating lamp lights in orange or the
message “CABLE NO INSERT”or “Blue picture”
appears on the screen, there is something unusual
about the status of reception. See “Power Save Mode”
or “Symptoms That Seemingly Appear to be Failures.”
45 ~ 47
ATTENTION
• Avoid repeatedly turning the PDP TV on and off at
short time intervals. Failures might result from such
operation.
• Turn off the main power switch before leaving the
PDP TV out of use for an extended period of time.
• If a power failure occurs while the main unit is
running, it would be powered on upon recovery from
the failure. Turn off the unit main power switch
before leaving the main unit.
26
OPERATING INSTRUCTIONS (continued)
MUTE button
CHANNEL S/T
buttons
INPUT/EXIT
button
INPUT SELECT
button
Input Switching
• Input can be switched in the sequence of TV ➝ HDTV ➝
PC ➝ HDMI ➝ Composite-Video ➝ S-Video ➝ Component
by pressing the INPUT button of the control panel.
TV
HDTV
Component
PC
S-Video
HDMI
Composite-Video
VOLUME
UP/DOWN
button
CHANNEL
UP/DOWN
button
• Input can be switched to TV by pressing PROGRAM +/buttons or NUMBER buttons of the remote control.
• Input can be switched by pressing the PC/HDMI, VIDEO or
DTT/TV buttons of the remote control.
Volume Adjustment
• The volume can be adjusted by pressing the VOLUME W / X
of the control panel or Vol+ and Vol- buttons of the remote
control.
• When a button is pressed, the volume adjustment status guide
will be displayed.
• The volume will increase when the volume X or Vol+ buttons are
pressed while the guide is being displayed.
• The volume will decrease when the volume W or Vol- buttons are
pressed while the guide is being displayed.
Audio Mute
• The audio volume can be temporarily muted by
pressing the MUTE button of the remote control.
• The muting can be cancelled by pressing the volume
W / X, Vol+/- buttons or MUTE button while the audio is
mute.
Volume setting value
Volume 32
Adjustment status guide display
27
OPERATING INSTRUCTIONS (continued)
Input Signal Screen Display
The input signal status can be displayed on the screen by pressing the RECALL button of the remote control.
• The display will go out in approximately 3 seconds.
TV
1
[I]
TV position
Sound mode
VIDEO/PC RGB
Analog RGB
1024X768 60Hz
Signal mode
Input frequency
Main video input
CATV
Composite VIDEO
Audio source
Sub video input
• Activate PIP by pressing PIP Input button to select desired video input.
• Press ▲▼ on the remote control to select audio source of video input.
• Picture Mode, Brightness, Contrast, Color, Tint, and Sharpness can be
adjusted by Audio source to settle on.
28
RECALL button
OPERATING INSTRUCTIONS (continued)
Using the Menu Screen (On-screen display system)
Control panel:
1. Press MENU of the control panel to display the OSD on your Plasma TV.
2. Use the PROGRAM ▲▼ to navigate to different menu item.
3. Use the VOLUME W X to adjust functions.
4. Press ENTER of the control panel to select functions.
5. Press EXIT of the control panel to quickly exit from the menu.
Remote control:
1. Press MENU on the remote control to display the OSD on your Plasma TV.
2. Use the ▲▼ to navigate to different menu item.
3. Use the W X to adjust functions.
4. Press ENTER on the remote control to select functions.
5. Press RTN on the remote control to go to the last page; press EXIT to quickly exit from the menu.
THERE ARE TWO DIFFERENT MODES FOR THE OSD AS BELOW:
TV/Video Mode: Displays when the TV, HDTV, Composite, S-video, Component or HDMI is selected.
PC Mode: Displays when the Analog RGB input is selected.
TV/Video Mode
Video
Image
Audio
Language
System
PC Mode
Picture Mode
Brightness
Contrast
Color
Tint
Sharpness
Color Temperature
Reset
P. Size
Set Border Color
Noise Reduction
3:2 Pull Down
Reset
Mute
Volume
Balance
Treble
Bass
Subwoofer
SRS WOW
Reset
English
繁體中文
Video
Image
Audio
Brightness
Contrast
H Position
V Position
Color Temperature
Reset
Clock Phase
Horizontal Clock
Auto Adjust
Mute
Volume
Balance
Treble
Bass
Subwoofer
SRS WOW
Reset
简体中文
日本語
Русский
Signal Format
Advance
PIP Set
TV Channel Setup (TV mode only)
Screen Wipe
29
OPERATING INSTRUCTIONS (continued)
Video Menu
TV/Video Mode
W
Selected characters
Picture Mode
Natural
X
Cinema
Dynamic
Setup hint
Natural: This setting is for normal lighting conditions.
Cinema: This setting is best for watching movie.
Dynamic: This setting is best for very bright ambient lighting.
Black is subdued for
Black is set off for
increased overall
increased overall
darkness.
brightness.
Narrows the gap
Broadens the gap
between brightness
between brightness
and darkness.
and darkness.
Decrease color
Increase color
Adjust to preference.
intensity.
intensity.
(Not available in Teletext mode)
Enhances red and
Enhances green and This is not available to adjust when receiving SECAM signal.
Tint
weakens green.
weakens red.
Then the character will be grayed out.
Sharpness
Soft
Sharp
Shift to the minus (-) side for a softer effect and plus (+) for sharper picture.
Brightness
Contrast
Color
Adjust to preference.
(Not available in Teletext mode)
Adjust for maximum visibility to suit the ambient brightness.
Adjust for most realistic skin color.
Color Temperature
Reset
Cool
Natural
User
Warm
Black/ White
(off the function)
-
Normally set to Cool.
The original factory settings for the items of this Menu page can be restored by
pressing the ENTER button.
PC Mode
W
Selected characters
Brightness
Contrast
X
Black is subdued for
Black is set off for
increased overall
increased overall
darkness.
brightness.
Narrows the gap
Broadens the gap
between brightness
between brightness
and darkness.
and darkness.
Setup hint
Adjust to preference.
Adjust for maximum visibility to suit the ambient brightness.
Moves the horizontal Moves the horizontal
H Position
V Position
Color Temperature
Reset
30
position to left
position to right
Moves down the
Moves up the vertical
vertical position.
position.
Cool
User
(off the function)
Natural
Adjust the left-side display position.
Adjust for maximum character clarity.
Warm
Black/ White
-
Normally set to Cool.
The original factory settings for the items of this Menu page can be restored by
pressing the ENTER button.
OPERATING INSTRUCTIONS (continued)
Image Menu
TV/Video Mode
W
Selected characters
X
Full
16:9 zoom
P. Size
Setup hint
4:3 Standard
Panoramic
Adjust to preference. Please refer to
4:3 Zoom
14
for more detail.
(Not available in Teletext mode)
Available for
TV/Composite/S-Video/Component(480i/480p/576i/576p)
signals.
Full
Component(720p/1080i)/HDMI
Adjust to when display 4:3 video.
Black
Gray
This turns the gray sidebars to the black sidebars when watching
normal mode screen size area. It is always set to Off when the
Set Border Color
monitor powered On. It is recommended to set to Gray to reduce the
panel image retention.
(Not available in Teletext mode)
Adjust to when display static image.
Noise Reduction
Off
Level1
Level2
Level3
If this is set from Off to Level3, it helps to reduce the noise
interference visible on the static image, especially in the weaker
signal reception areas.
Disable
3:2 Pull Down
Reset
Enable
Adjust to improve the picture quality.
(off the function)
-
The original factory settings for the items of this Menu page can be
restored by pressing the ENTER button.
PC Mode
W
Selected characters
Clock Phase
X
Slows the dot clock
Advances the dot
phase (shifts slightly
clock phase (shifts
to left).
slightly to right).
Setup hint
Adjust for clear character visibility.
Reduces the dot clock Increases the dot
frequency (shrinks the clock frequency
Horizontal Clock
right side).
(expands the right
Adjust for maximum character clarity.
side).
Pressing the ENTER button, automatic regulation is started.
Auto Adjust
(off the function)
-
Horizontal Position, Vertical Position, Horizontal Clock and Clock Phase are
adjusted automatically.
31
OPERATING INSTRUCTIONS (continued)
Audio Menu
W
Selected characters
X
Disable
Mute
Turns down the
Volume
volume.
Enable
Treble
Bass
sound.
sound.
Suppresses treble.
Enhances treble.
Suppresses bass.
Subwoofer
Adjust to turn off the sound.
Turns up the volume. This is to set the volume for speaker.
Suppresses right-side Suppresses left-side
Balance
Setup hint
Enhances bass.
On
Off
On
Off
Adjust to preference.
Adjust to preference.
(When SRS WOW select “On”, this function is not available)
Adjust to preference.
(When SRS WOW select “On”, this function is not available)
Adjust to preference.
(When SRS WOW select “On”, this function is not available)
SRS WOW
Reset
(off the function)
Adjust to preference.
-
The original factory settings for the items of this Menu page can be restored by
pressing the ENTER button.
SRS WOW is an audio enhancement technology from SRS Labs that provides deep, rich bass on any speaker system without the need
for a subwoofer or additional extra physical components. For systems with a subwoofer, SRS WOW complements and enhances the
bass performance. This feature can be set to On or Off.
NOTES:
WOW, SRS and the
symbol are trademarks of SRS Labs, Inc. SRS WOW technology is incorporated under
license from SRS Labs, Inc.
Language Menu
TV/Video Mode
Selected characters
S
T
English
繁體中文
Language
简体中文
Русский
32
日本語
Setup hint
Adjust to preference.
OPERATING INSTRUCTIONS (continued)
System Menu
TV/Video Mode
NOTES: When operating the TV at first time, its TV system is at “default factory mode” and this mode cannot display the image
normally on the screen. In order to watch the TV program without problem, please execute “TV Channel Setup” menu for
normally display..
W
Selected characters
X
Setup hint
Signal Format
(off the function)
Advance
Press ENTER button to select the following functions
3D Comb
Panel Lock
-
On
Off
On
Off
Press the ENTER button to show the information of the current input signal.
Improve the picture quality for TV, Composite-video.
This is for locking out the control panel function.
Adjust to prevent children from touching.
Adjust to preference.
Off
Mode
Mode 1
Mode 2
The moves the picture around the screen to reduce the panel image retention.
This is where stationary objects, such as screen logos, leave a slight image
visible after they should have disappeared.
Move Screen
Adjust to preference.
Time
This moves the picture around the screen in small amounts, at set intervals, to
0~255 sec
reduce the panel image retention. This is where stationary objects, such as
screen logos, leave a slight image visible after they should have disappeared
The original factory settings for the items of this Menu page can be restored by
Reset
(off the function)
PIP Set
Press ENTER button to select the following functions
Off
Source
AV
Small
Size
-
SV
TV
Medium
pressing the ENTER button.
DTT
Large
Adjust to preference.
Adjust to preference.
9 positions for selection:
Upper Left, Upper Center, Upper Right,
Position
Middle Left, Middle Center, Middle Right,
Adjust to preference.
Lower Left, Lower Center, Lower Right
Main
Audio Source
Black is subdued for
Brightness increased overall
PIP Display
Contrast
Color
PIP
Adjust to preference.
Black is set off for
increased overall
darkness.
brightness.
Narrows the gap
Broadens the gap
between brightness
between brightness
and darkness.
and darkness.
Decrease color
Increase color
intensity.
intensity.
-
Adjust to preference.
Adjust for maximum visibility to suit the ambient brightness.
Adjust to preference.
Swap
(off the function)
Press the ENTER button to change main and PIP display.
TV Channel Setup
Press ENTER button to select the following functions (only available under TV mode)
Select the channel entry method between position setting or direct setting. And
press the ENTER button in SEARCH function to fix it. Please use auto search
when you first use your TV.
Channel Auto Mode
Position
Direct
• [Position] search the channel by frequency from 48.25~863.25MHz. We
suggest to use these function for the channel setting
Search
• [Direct] search the channel by CCIR PAL B/G table. Provide the faster
speed than position mode, but some channels which are not in the table
may be lost.
Search
(off the function)
-
Press the ENTER button and it starts the auto tuning.
33
OPERATING INSTRUCTIONS (continued)
System Menu (continued)
TV/Video Mode
W
Selected characters
Program
Setup hint
Increase channel
Select PROGRAM and press the W/X buttons to choose the programmed
number
number
number
Band
Channel
X
Decrease channel
CC
Select BAND and press the W/X buttons to choose the band type. ( CH-AIR /
CH
CC-CATV)
Decrease channel
Increase channel
number
number
Select CHANNEL and press the W/X buttons to choose the channel number.
Select COLOR SYSTEM and press the W/X buttons to choose the color
Channel
Manual
Search
Color
System
AUTO
PAL
NTSC3.58
SECAM
system. (AUTO/PAL/SECAM/NTSC3.58)
(NOTE : If you do not have a clear picture or no color appears, change the
color system.
(Use to add
the channel
AUTO
by manual)
M
Sound
System
DK
Fine Tune
Store
Decrease
number
Sort (Press SORT EDIT
button to modify the list)
BG
Increase
number
Storing the manual setting
West Europe
Teletext Language
I
system.(AUTO/M/BG/I/DK)
(NOTE : If the SOUND SYSTEM setting for a TV channel is incorrect, it may
proven the sound from being issued.
If the channel reception is poor, select FINE TUNE and press the W/X buttons
to fine tune the program.
Select STORE and press the W/X buttons to store the manual setting. When
stored, OK will be displayed for short seconds.
East Europe
Persian
Cyrillic
Arabic
Greek
(off the function)
Select SOUND SYSTEM and press the W/X buttons to choose the sound
-
Select the language depends on your country or area.
NOTES
This is used to white pattern to reduces the screen burn made by continuous
Screen Wipe
(off the function)
-
on-screen displays. Pressing the ENTER button to start the function and press
EXIT button to leave.
34
OPERATING INSTRUCTIONS (continued)
System Menu (continued)
Sort (Press SORT EDIT button to modify the list)
NOTES
Press ENTER button to select the following functions.
Using the NAME, DELETE, or INSERT functions rewrites the current programmed numbers list.Therefore, the programmed number of some of the
TV channels will change.Follow the operation description of a function you want to use and operate the function.
‧Name : This function registers a channel name (ID) to a TV channel.
1. Press the S/T and W/X buttons to choose a TV channel.Every time you press the S/T and W/X buttons, the programmed number changes
and the picture of the TV channel stored in the programmed number appears on the screen.
2. Press the red button to start the NAME function.
3. Press the S/T and W/X buttons to edit the channel name you want to give the TV channel.
4. Press the red button to store the setting.
To return to the INITIAL SETUP menu : Press the RETURN button.
To exit a menu instantly : Press the EXIT button.
‧Insert : This function changes a programmed number of a TV channel.
1.Press the S/T and W/X buttons to choose a program number for which you want.Every time you press the S/T and W/X buttons, the
programmed number changes and the picture of the TV channel stored in the programmed number appears on the screen.
2.Press the green button to start the INSERT function.
3.Press the S/T and W/X buttons to choose a new program number.
4.Press the green button to insert the channel into the new program number.
To return to the INITIAL SETUP menu : Press the RETURN button.
To exit a menu instantly : Press the EXIT button.
‧Delete : This function deletes a TV channel you do not want to list.
1.Press the S/T and W/X buttons to choose a TV channel
Every time you press the S/T and W/X buttons, the programmed number changes and the picture of the TV channel stored in the
programmed number appears on the screen.
2.Press the blue button to start the DELETE function.
3.Press the S/T and W/X buttons to edit the channel name you want to delete the TV channel.
4.Press the blue button to store the setting.
To return to the INITIAL SETUP menu : Press the RETURN button.
To exit a menu instantly : Press the EXIT button.
35
OPERATING INSTRUCTIONS (continued)
Using the HDTV Menu Screen
1. Make sure the physical connection is properly connected.
2. Switch on the TV.
3. Select the HDTV input on your TV by using the remote control.
4. If the PDP is moved to a different location. You should reset the receiver and do the channel scanning all over again.
USING THE HDTV ON-SCREEN DISPLAY (OSD) CONTROLS
1. Press DTT MENU on the remote control to display the MENU banner.
2. Use the ▲▼W X to navigate to different menu item.
3. Use the W X to adjust functions.
4. Press ENTER on the remote control to select functions. Press RTN to jump back the last page of menu.
5. Press RTN on the remote control to go to the last page; press EXIT to quickly exit from the menu.
HDTV Main Menu
Edit Channel
Parental Guidance
TV Main List
No Block
Block G and above
Block PG and above
Block M and above
Block MA and above
Block AV and above
Block R and above
Block All
Manual Scan
Installation
General Setting
System
36
Quick Scan
Auto Scan
Restore Defaults
Audio Setup
Option Setup
Change Pin
Local Time
Status
This is used to edit the channel from the TV channel list.
Blocks selected HDTV-rating and all ratings below it.
(Enter the password to change setting).
Search scan TV channel by channel number, frequency, bandwidth and
priority
Search scan TV channel by your location
Automatically search scan TV channel
Sets HDTV back to default settings
Adjusts HDTV audio setting
Adjusts HDTV OSD display setting
To change password
Sets your local time
Shows the software version of your set
OPERATING INSTRUCTIONS (continued)
Edit Channel
1. Press the DTT MENU button to display the MENU banner.
2. Use the arrow keys ▲ or ▼ to highlight “Edit Channel”, then press ENTER to show
the TV channel list.
3. Use the arrow keys ▲ or ▼ to highlight the channel you want to edit.
● SET LIST
On pressing the red button on the remote control, you can toggle between TV MAIN LIST, FAVORITE LIST 1 and FAVORITE LIST 2,
below the small TV screen on this menu you can see the name of the list.
When you haven’t set up FAVORITE LIST, there’s only TV MAIN LIST. Please refer to the following option COPY to learn how to set up
the FAVORITE LIST.
● COPY (for set up FAVORITE LIST)
You can copy a channel from TV channel list to the favorite list.
a. Highlight the channels in the channel list
b. Use green key select the channel you want to copy to the favorite list.
c. Each time you press the green button you will see "F1","F2" or "F1/2" appears one after another, which means the highlighted channel
can be assigned to "TV Favorite List 1", "TV Favorite List 2" or in both "TV Favorite List 1" and "TV Favorite List 2". Make sure all
the channels you want to copy to the favorite channel list are correctly selected.
d. Press the green key to copy the channel to the favorite channel list.
● DELETE
You can delete a channel from the TV channel list if you do not want it.
a. Select the channel from the TV channel list using the ▲ or ▼ arrow keys.
b. Press yellow key and X mark appears.
c. Press the enter key to delete the selected channel.
● Lock/unlock
Use the ▲ or ▼ arrow keys to select the desired option and press blue key to “Lock” or “Unlock” channels/programs.
● Sort
There are three groups for your desired channels list once you press the number key from 1 to 3, which include, A – Z, Z – A and channel
number.
● MOVE
You can re-arrange the channels in the TV channel list.
a. Select the required channel by using the scroll keys.
b. Press the W or X arrow key to select the channel. A yellow mark will appear to show the selection.
c. Use the ▲ or ▼scroll keys or numerical keys to move the selected channel to the desired location.
d. If you want to move a group of channels, highlight the channels and press right arrow key first, and use the scroll key to highlight the
entry you want to move in, then press left arrow key to apply move.
37
OPERATING INSTRUCTIONS (continued)
Parental Guidance
1. You can set “Parental Locking” for a selected channel to prevent your children from
viewing sensitive material. Once you set the parental rating for the particular channel,
the parental rating transmitted with the channel will verify if the received rating is higher
than the parental lock rating. A pop-up message will say that the channel is locked.
To see the channel, you have to enter a password in the Check Password Menu before
viewing the channel. The default password is 0000.
2. This option will allow you to set the Parental Guidance Level for the receiver. You could
use ▲ or ▼ arrow keys to scroll between different ratings. On selecting this option,
3. check password menu will pop-up. After giving the correct password, you can enter
into the menu, which is shown below, for censoring the channels according to the
age limits.
38
OPERATING INSTRUCTIONS (continued)
Installation
Before you use Digital TV, the available channels must first be scanned and memorized.
1. Press the DTT MENU button to display the MENU banner.
2. Use the arrow keys ▲ or ▼ to highlight “Installation” and enter default password
“0000” to show four sub-menus.
Manual Scan
a. Press ▲ or ▼ buttons to highlight the “Manual Scan”, and then press ENTER to lunch
the auto scan. A “Manual Scan” window will show.
b. You can use the ▲ or ▼ keys to highlight a single channel, and just simply fill in all
information which are inquired on the screen by remote control and then press ENTER
button on the remote control to start manually scanning this single channel’s signal.
Quick Scan
a. Press ▲ or ▼ buttons to highlight the “Quick Scan”, and then press ENTER to lunch
the auto scan. An “Quick Scan” window will show.
b. Upon selecting the “Quick Scan” Option from the Search Channel menu, the default
city will be displayed.
39
OPERATING INSTRUCTIONS (continued)
Installation (continued)
c. Press ENTER on the city you choose by ▲ or ▼ keys, the channels / programs will be
presented automatically.
Note:
Current listed cities are for Australia; we will set individual cities for every different nations.
Auto Scan
a. Press ▲ or ▼ buttons to highlight the “Auto Scan”, and then press ENTER to lunch
the auto scan. An “Auto Scan” window will show the SCAN status.
b. Once the digital TV signal is scanned, the channel number and program name will be
shown on the “Auto Scan List”.
c. When it is complete (even in processing) you can press EXIT key to leave the window
and enjoy watching DTT programs.
Restore Defaults
If you want to restore defaults, choice “OK” then all settings will be lost; if not choice “EXIT”.
40
OPERATING INSTRUCTIONS (continued)
General Settings
1. Press the DTT MENU button to display the MENU banner.
2. Use the arrow keys ▲ or ▼ to highlight “General Setting” and press ENTER key on
remote control to show four sub-menus.
3. It will show “Audio Setup”, “Option Setup”, “Change Pin” and “Local Time”.
Audio Setup
a. Select the “Audio setup” of the “General Setting” OSD.
b. You may choice PCM or Dolby then press
ENTER key on the remote control.
c. Choice “OK” then the settings will be
saved; if not press “EXIT”.
Option Setup
a. Select the “Option setup” of the “General Setting” OSD.
b. Information box timeout: by adjust the
timeout, you may change the time interval
of the menu showing when you press DTT
menu button on the remote control or
doing the channel change.
c. Choice “OK” then the settings will be
saved; if not press “EXIT”.
41
OPERATING INSTRUCTIONS (continued)
General Settings (continued)
Change Pin
a. Select the “Change PIN” of the “General Setting” OSD.
b. Follow the instruction to change the PIN for Installation menu and parental control.
NOTES: 1. Before you change the password, uses the default password “0000” to enter
the Menu item which requires the password.
2. If you forget the password, please see the following steps to set the new one:
a. Press YELLOW, GREEN, GREEN, RED, BLUE in change pin menu.
b. Press any 4 numbers.
c. Enter and confirm new password.
Local Time
a. Select the “Local Time” of the “General Setting” OSD.
b. You may choice the time zone you are
located.
System
1. Press the DTT MENU button to display the MENU banner.
2. Use the arrow keys ▲ or ▼ to highlight “System” and press ENTER key on remote
control to “Status” sub-menu.
3. Press ENTER key again to show the DTT software version for service.
42
OTHER FUNCTIONS
Audio Switching
A2 / Sound Multiplex (TV mode)
• The I/II button in remote control is useful for sound multiplex signal.
Otherwise pressing this button will have no effect.
BILINGUAL / DUAL sound broadcast
When bilingual program is received, sound mode display appears as shown on right.
Press the I/II button to select the sound to be heard.
Each time the button is pressed, [I]Language A, [II]Language B or ▼ Mono appear cyclically on the screen.
Sound multiplex signal received
[I]
[II]
▼
STEREO sound broadcast
When a stereo program is received, sound mode display will appear, and you can press the I/II button to select between stereo and
mono sound.
Each time the button is pressed, ▼ Mono or
Stereo appear cyclically on the screen.
When receiving NICAM signals, NICAM display will appear as below.
Sound multiplex signal received
▼
Monaural sound broadcast
When a monaural program is received, sound mode display will appear.
NOTE
• If sound signal is not strong enough for quality reception, press the I/II button until ▼appears on the screen to receive a
clear mono sound.
• If sound has hiss noise or keep switching between stereo and mono mode due to signal condition, press the I/II button until
▼appears on the screen to receive a clear mono sound.
43
OTHER FUNCTIONS (continued)
Signal Check (Analog RGB mode)
Changes in the signal status are displayed on the screen as they arise.
Status
Display
A guide is displayed for the
input terminal and the
horizontal and vertical sync
frequency.
• A guide displays No Input
Signal, and Power Save
(for approx. 5 sec.)
• When the condition
continues where the sync
signal cannot be detected,
indicator lamp of power
source changes in orange
and the mode switches to
power save mode.
When the input signal does A guide displays No Input
Signal.
not match the monitor
specifications or is in an
unstable status.
When Mode Display is set to
ON, the input signal is
switched or when the
RECALL button is pressed.
When the sync signal is no
longer detected.
Action
Recheck the personal
computer power switch
status and the
connection status.
Recheck the input
signal specifications.
Analog RGB
1024X768 60Hz
CABLE NO INSERT
Signal Check (TV/Video mode)
Changes in the signal status are displayed on the screen as they arise.
Mode
Status
Display
When the TV signal • A guide is displayed for
searching and counting down
is no longer
2 minutes.
detected.
• If the TV signal cannot be
detected after 2 minutes, the
PDP TV will turn off directly
and indicator lamp is going to
red.
• A guide displays No Sync.
Video When the sync.
signal is no longer Signal in orange.
detected.
TV
44
Action
• Recheck the antenna
connection status.
• Reception other than
those of broadcasting
stations can be
considered.
(Blue picture)
• Recheck the device
power switch status
and the connection
status.
• Recheck the device
connection status.
• Recheck the input
signal specifications.
OTHER FUNCTIONS (continued)
Power Save Mode
When the Analog RGB input is selected
• When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the
computer is not being used to reduce power consumption by this unit.
RGB sync
Horizontal
signal
Vertical
PC signal
Operation mode
Indicating lamp
Power consumption
Yes
Yes
Active (normal display)
On
Lights green
350 W
No
Yes
Yes
No
Blank (no display)
Off
Lights orange
3W (100V~240V)
No
No
Returning to operating status
• Operate the personal computer, or press either the INPUT button of the main unit or the PC button of the remote control.
45
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact
your dealer.
Customer servicing can be hazardous.
Symptom
Point to check
• No picture with the power-indicating
lamp off.
• Check the way the power cord is connected.
• Press the power switch.
• The message “CABLE NO INSERT” is
displayed.
• Blue picture with the power indicating
lamp lights in green.
No input signal is detected.
• Check the way the signal cable is connected.
• Make sure that the switch of the computer, imaging
equipment, etc., is turned on.
• Make sure the computer is not in the power-save mode.
• Check to see if the input selection matches the connection
terminal.
An input signal is not received normally.
• Check to see if the input signal matches the
specifications.
• Check the way the signal cable is connected.
• Check the contrast and brightness settings (adjust them for
higher contrast and brightness).
• Check the way the signal cable is connected.
• Adjust the dot clock frequency and phase. (Adjust the dot
clock frequency first, the dot clock phase next.)
(PC RGB input)
CABLE NO INSERT
• Blue picture is displayed.
• The power indicating lamp is normally lit
but no picture.
• The display image appears flowing
slantwise.
• Text displayed across the screen
appears vertically streaked, with the
characters in vertical columns blurred.
• Adjust the dot clock phase for the clearest viewing.
(PC RGB input)
• The remote control does not work.
• Check to see if the batteries are loaded in the remote
control in opposite direction.
• Check to see if the batteries in the remote control are OK.
• Check to see if the displayed input signal match the PDP
TV specification by pressing RECALL button.
• Turn off the Move screen.
• Turn off the Move screen.
• The display has lack of picture around
the screen.
(PC RGB input)
• The temperature of the display panel surface is high.
46
25
26
24
24
44
21
30
31
51
• Text displayed across the screen
appears blurred.
• A fine pattern flickers when displayed on
the screen.
• The display image does not appear in
the normal position.
See page
31
51
11
33
49
33
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. In some cases, this may
cause the temperature of the panel surface to increase.
Please note that this is not a malfunction.
-
TROUBLESHOOTING (continued)
Symptoms That Seemingly Appear to be Failures (continued)
Symptom
Point to check
• There are locations on the screen that are different from the
periphery (*).
*Points that do not light, points with brightness different from
that of the periphery, points with color different from that of
the periphery, etc.
• Vertical stripes appear, depending on the screen contents.
• High-precision technology is used to manufacture the
plasma display panel, However in some cases, there are
minor defects in some parts of the screen. Please note that
this is not a malfunction.
• The plasma display panel is lighting the phosphors by the
discharge of internal radiation. Depending on the screen
contents, in rare cases this may cause vertical stripes to
appear because of failure to light. Please note that this is
not a malfunction.
• Coarse horizontal stripes appear in FULL display.
• Adjusting the Clock Phase will reduce the horizontal
stripes.
(PC RGB input)
• Flickering in the form of horizontal lines oscillating up and • If the direct frequency from the computer is below 85Hz, try
down. (PC RGB input only)
a higher frequency (upper limit 85Hz). There may be a
slight attenuation of the current image.
• The top of the monitor heats up.
• When used for long periods of time, the top of the monitor
may heat up. This is not a malfunction.
• Text characters are displayed with varying thicknesses.
• The thicknesses of characters and lines may vary if images
with a vertical resolution greater than 512 lines are
displayed; however, this is not a malfunction.
• The screen becomes dark and the images can not be seen • This sometimes occurs when a component output VTR
during VTR special playback (fast forward, rewind)
such as the 480i is connected.
This is not a malfunction; therefore, please take note that
this may occur. When it does occur, change to composite
output, or S-video output.
• During PIP mode, sub pictures are not displayed.
• Sub pictures image might not be able to be displayed,
depending on the combination.
(Refer to the table of PIP input table)
• The screen display sizes are not switched.
• The screen display size is fixed at “Full” as receiving VGA
signal.
• Images from HDMI are not displayed.
• Check the cable and output format of connecting device.
(Refer to “Connecting to an Audio Visual Device”.)
See page
-
-
31
51
-
-
15
20
21
23
48
47
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the
adjustments suggested below. (only for PC RGB)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (Figure 1).
(PC RGB input).
Figure 1
Example
Adjustment
Procedure
1) Press the MENU button. The Main Menu will be displayed.
2) Press the ▼ button and select “IMAGE”.
3) Press the ENTER button. The “IMAGE” Menu will be displayed.
4) Press the ▼ button and select “Auto Adjust”.
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the ▼ button and select “IMAGE”.
7) Press the ENTER button. The Setup Menu will be displayed.
8) Press the ▼ button and select “Horizontal Clock”.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock
adjustment.)
9) Press the W or X buttons and search for clear characters over the entire screen.
10) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
• The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (Figure 2).
A fine pattern flickers when displayed on the screen (Figure 3).
Figure 3
Figure 2
Example
Adjustment
procedure
48
1) Press the MENU button. The Main Menu will be displayed.
2) Press the ▼ button and select “IMAGE”.
3) Press the ENTER button. The Setup Menu will be displayed.
4) Press the ▼ button and select “Auto Adjust”.
When adjustment is not possible with Auto Adjust
5) Press the MENU button. The Main Menu will be displayed.
6) Press the ▼ button and select “IMAGE”.
7) Press the ENTER button. The Setup Menu will be displayed.
8) Press the ▼ button and select “Clock Phase”.
(Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
9) Press W or X buttons to make the text appear clean
9) Press W or X buttons to make the text appear without
across the screen.
flickering.
PRODUCT SPECIFICATIONS
Panel
Display dimensions
Resolution
Net dimensions
Net weight
Ambient
Temperature
conditions
Relative humidity
Power supply
Power consumption/at standby
Audio output
Approx. 42 inches (926 (H) x 525 (V) mm, diagonal 1064mm)
1024(H) x 1024 (V) pixels
1036 (W) x 713 (H) x 121 (D) mm
33.6 kg
Operating : 5°C to 35°C, Storage : 0°C to 40°C
Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
AC100 - 240V, 50/60Hz
350W / <3W
speaker 10W + 10W (8Ω)
(RGB input)
Input terminals
D-Sub input terminal (D-sub 15-pin)
PC audio input terminal (3.5mm Stereo Mini Jack)
Input signals
0.7Vp-p, analog RGB (Recommended Signal)
Sync signals
H/V Separate, TTL level[2kΩ]
H/V Composite, TTL level[2kΩ]
Sync on green, 0.3Vp-p[75Ω]
Recommended signal
17 modes
51
(Video input)
Input terminals
Input signals
Output Signal
Recommended signal
Composite video input terminal (RCA)
Composite video L/R audio input terminal (RCA)
S-Video input terminal
S-Video L/R audio input terminal (RCA)
Component - YCBCR/YPBPR video input terminal (RCA)
Component - YCBCR/YPBPR L/R audio input terminal (RCA)
HDMI input terminal
Composite video: PAL, SECAM, NTSC
Component - YCBCR/YPBPR video: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60,
720p/50, 720p/60
S-Video: PAL, SECAM, NTSC
HDMI: HDMI input signal
Video Output: TV/Composite video/S-Video output terminal (RCA)
Audio Output: L/R audio output terminal (RCA)/Subwoofer output terminal(RCA)/
S/P DIF
19 modes
50
(RF input)
Input terminals
ANT : 75Ω Unbalanced
Analog RF Video System
PAL B,G/ I / D,K
NTSC-M
SECAM B,G / D,K
Digital RF Video System
DVB-T
This television takes at least 30 minutes to attain the status of optimal picture quality.
49
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List
With composite input and S-Video input.
Signal mode
No.
1
2
Signal Name
NTSC4.43
NTSC3.58
PAL
SECAM
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
59.94
15.734
—
50.00
15.630
—
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
15.63
15.73
31.26
31.47
28.13
33.75
37.00
45.00
—
—
—
—
—
—
—
—
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
Remarks
31.47
15.63
15.73
31.25
31.47
28.13
33.75
37.50
45.00
25.18
27.00
27.00
27.00
27.00
74.25
74.25
74.25
74.25
VESA
EIA-861B
EIA-861B
EIA-861B
EIA-861B
EIA-861B
EIA-861B
EIA-861B
EIA-861B
Resolution
Vertical frequency
(Hz)
525
625
Remarks
With Component input
Signal mode
No.
1
2
3
4
5
6
7
8
Signal Name
Resolution
576i
480i
576p
480p
1080i/50
1080i/60
720p/50
720p/60
576
480
576
480
1080
1080
720
720
Vertical frequency
(Hz)
50.00
59.94
50.00
59.94
50.00
60.00
50.00
60.00
Remarks
With HDMI input
Signal mode
No.
1
2
3
4
5
6
7
8
9
50
Signal Name
Resolution
VGA
576i
480i
576p
480p
1080i/50
1080i/60
720p/50
720p/60
640 x 480
720(1440) x 576
720(1440) x 480
720 x 576
720 x 480
1920 x 1080
1920 x 1080
1280 x 720
1280 x 720
Vertical frequency
(Hz)
59.94
50.00
59.94
50.00
59.94
50.00
60.00
50.00
60.00
PRODUCT SPECIFICATIONS (continued)
Recommended Signal List (continued)
With Analog RGB signal input
Signal mode
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Signal Name
Resolution
VGA
VGA
VGA
VGA
VGA
SVGA
SVGA
SVGA
SVGA
SVGA
XGA
XGA
XGA
XGA
XGA
XGA
XGA
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 720
1280 x 960
1280 x 1024
Vertical frequency
(Hz)
70.08
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
60.00
60.00
60.02
Horizontal
frequency (kHz)
Dot clock
frequency (MHz)
31.47
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
45.00
60.00
63.98
25.18
25.18
31.50
31.50
36.00
36.00
40.00
50.00
49.50
56.25
65.00
75.00
78.75
94.50
74.30
108.00
108.00
Remarks
.The type of video board or connecting cable used may not allow for correct displays adjustment of Horizontal Position,
Vertical Position, Horizontal Clock and Clock Phase.
.The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or
higher is input to it.
.The monitor differentiates the signal modes according to the horizontal an vertical frequencies and the horizontal and
vertical sync signal polarities. Note that different signals having all these elements alike may be handled as the same
signal.
.Displaying images with more than 512 lines of vertical resolution at Full display(compressed display) can result in the
interpolation of stripes
51
52
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement