HDM-EXT-0107C HDMI Extender over Single Cat.X with HDBasedT, RS-232, Bi-directional IR,

User Manual
HDM-EXT-0107C
HDMI Extender over Single Cat.X with
HDBasedT, RS-232, Bi-directional IR,
Ether net & POE
rev: 121219
Made in Taiwan
Safety and Notice
The HDM-EXT-0107C HDMI Extender over Single Cat.X with HDBasedT, RS-232, Bidirectional IR, Ethernet & POE has been tested for conformance to safety regulations
and requirements, and has been certified for international use. However, like all electronic
equipments, the HDM-EXT-0107C should be used with care. Please read and follow the safety
instructions to protect yourself from possible injury and to minimize the risk of damage to the
unit.
● Follow all instructions and warnings marked on this unit.
● Do not attempt to service this unit yourself, except where explained in this manual.
● Provide proper ventilation and air circulation and do not use near water.
● Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
● Use only the power adapter and power cords and connection cables designed for this unit.
● Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
TABLE OF CONTENTS
INTRODUCTION ........................................................................................................... 1
FEATURES .................................................................................................................... 1
SPECIFICATIONS ......................................................................................................... 2
PACKAGE CONTENTS ................................................................................................. 3
PANEL DESCRIPTIONS ............................................................................................... 4
Transmitting unit ► HDM-EXT-0107C [Tx] .................................................................... 4
Receiving unit ► HDM-EXT-0107C [Rx] ...................................................................... 5
IR PASS-THROUGH ..................................................................................................... 6
HARDWARE INSTALLATION ........................................................................................ 7
EDID LEARNING ........................................................................................................... 7
PIN DEFINITION ........................................................................................................... 8
NOTICE ......................................................................................................................... 9
PERFORMANCE GUIDE .............................................................................................. 9
INTRODUCTION
The HDM-EXT-0107C HDMI Extender over Single Cat.X with HDBasedT, RS-232, Bi-directional
IR, Ethernet & POE boosts up your video/audio transmission distance up to m (ft) in HDTV 1080p with
48-bit color depth. HDM-EXT-0107C also supports the most advanced 3D video format complaint with
HDMI specification and therefore guarantees the highest 3D video compatibility on the market. With
only one cost effective Cat.5/5e/6 cable, users can readily extend HDTV sources from DVD players,
Blu-ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant display
monitors including HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the
latest HDMI technology, deep color video, DTS-HD or Dolby TrueHD audio, and HDCP supports and
compatibility are all further insured. This flexibility makes HDCP compliant DVD players or PS3 transmit
utmost high quality video and audio with a greater distance at the minimal cost, when integrating several
components apart. In addition, HDM-EXT-0107C is also equipped with bi-directional IR pass-through
path and RS-232 serial port control. These bonus features allow users to boost IR control distance up
to 100m (330 ft) and makes IR control possible through only single Cat.5/5e/6 cable including HDMI
signals. In addition, serial port offers the convenient path for interactive application, such as touch
panels. In addition, HDM-EXT-0107C also supports POE (Power over Cable) which can power both units
from TX or RX with power supply.
The HDM-EXT-0107C includes two units: transmitting unit HDM-EXT-0107C-TX and receiving unit HDMEXT-0107C-RX. The transmitting unit is used to capture the input HDMI / DVI signals with IR control
packets and carry the signals via one cost effective Cat.5/5e/6 cable. The receiving unit is responsible
for equalizing the transmitted HDMI signal and reconstructing IR and serial control signals. HDM-EXT0107C offers the most convenient solution for digital signage with long distance A/V transmission path,
and with 10G transmission width ready, HDM-EXT-0107C is ready for your next HDMI generation and
applications!
FEATURES
● Support HDMI Deep Color, full 3D & [email protected] (HDBaseT technology)
● Extend the transmission up to 100m (330ft) from the HDMI source at Full HD 1080p 48-bit
● Support POE(Power over Cable) which can power both units from TX or RX with power supply.
● HDCP & EDID Bypass
● CEC support
● Auto equalization
● Pure unaltered uncompressed 7.1ch digital HDMI over Cat.5/5e/6 cable transmission
● DTS-HD Master Audio and Dolby TrueHD high bit rate audio support
● Support full frequency IR signal from 20KHz to 60KHz
● Bi-directional IR path-through
● Full Duplex RS-232 control up to 115,200 bps through connector
● Integrated Ethernet port for LAN/ network device
● Wall mounting housing design for easy and robust installation
i
The length depends on the characteristics and quality of the cables. Higher resolutions and
longer transmission distances require low skew cables (<25ns/100m) for best performance.
Unshielded CAT6 with metal RJ-45 connectors is recommended.
1
SPECIFICATIONS
Model Name
Technical
HDM-EXT-0107C
HDM-EXT-0107C [Tx]
HDM-EXT-0107C [Rx]
Transmitter [TX]
Receiver [RX]
Role of usage
HDMI compliance
HDMI Deep Color, full 3D & [email protected]
HDCP compliance
Yes
Video bandwidth
Single-link 340MHz [10.2 Gbps]
Video support
480i / 480p / 720p / 1080i / 1080p60
HDMI over UTP
[email protected] 100m (330ft) [CAT5e]
Audio support
Surround sound [up to 7.1ch] or stereo digital audio
Equalization
Auto
Input TMDS signal
1.2 Volts [peak-to-peak]
Input DDC signal
ESD protection
PCB stack-up
5 Volts [peak-to-peak, TTL]
[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset — ±8kV
6-layer board [impedance control — differential 100Ω; single 50Ω]
IR pass-thru
Bi-directional
RS-232 support
Yes
Ethernet support
Yes
POE support
Yes
Input
1x HDMI / 1x 3.5mm
1x RJ-45(Video) / 1x 3.5mm
Output
1x RJ-45(Video) / 1x 3.5mm
1x HDMI / 1x 3.5mm
In / Out
1x DIN9 / 1x RJ-45(Ethernet)
1x DIN9 / 1x RJ-45(Ethernet)
HDMI source control
Controllable via IR pass-through from RX to TX with IR extenders
IR remote control
Type A [19-pin female]
HDMI connector
DIN-9
RJ-45 connector
WE/SS 8P8C(Reverse Mode)
Rotary control switch
3.5mm connector
None
IR receiver / IR blaster
IR receiver / IR blaster
Mechanical
Housing
Dimensions
[L x W x H]
Weight
Metal enclosure
Model
85 x 60 x 25mm [3.3" x 2.4" x 1"]
Package
270 x 175 x 80mm [10.6" x 6.9" x 3.1"]
Carton
450 x 370 x 300mm [1'6" x 1'3" x 11.8"]
Model
320g [11 oz]
Package
720g [1.6 lbs]
Fixedness
Wall-mounting case with screws
Power supply
Power consumption
Operation temperature
Storage temperature
Relative humidity
2
24V1A
Max 12W
0~40°C [32~104°F]
-20~60°C [-4~140°F]
20~90% RH [no condensation]
PACKAGE CONTENTS
● 1x HDM-EXT-0107C [TX & RX]
● 1x IR blaster
● 1x IR receiver
●1
x DC 24V in-line with C7 power cord
● 1x User manual
CONNECTION WARRANTY
3
PANEL DESCRIPTIONS
Input Panel
Transmitting unit ► HDM-EXT-0107C [Tx]
1
2
3
4
5
6
1 IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
2 IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
3 HDMI IN: Connects to a HDMI source with a HDMI male-male cable
4 Ethernet
5 LED: Power indicator
6 +24V DC: Connect to a 24V DC power supply.
Output Panel
7
8
9
10
7 DIP Switch: PIN#1: Setup the RS-232 mode for serial communication channel.
PIN#2: For Firmware Update
8 RS-232: Connect to serial port device with a DSUB-9 male-male or male-female cable here
9 R
J45: Plug in a Cat-5/5e/6 cable that needs to be linked to the transmitting unit HDM-EXT-0107C-RX.
ED: TX/RX link indicator
10 L
4
Input Panel
Receiving unit ► HDM-EXT-0107C [Rx]
1
2
3
4
5
6
1 IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
2 IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
3 HDMI OUT: Connect to a HDMI display with a HDMI male-male cable
4 Ethernet
5 LED: Power indicator
6 +24V DC: Connect to a 24V DC power supply.
Output Panel
7
8
9
10
7 DIP Switch: PIN#1: Setup the RS-232 mode for serial communication channel.
PIN#2: For Firmware Update
8 RS-232: Connect to serial port device with a DSUB-9 male-male or male-female cable here
9 R
J45: Plug in a Cat-5/5e/6 cable that needs to be linked to the transmitting unit HDM-EXT-0107C-RX.
ED: TX/RX link indicator
10 L
DIP Switch Position
TX & RX
ON[
Solid
Stranded
ON[
OFF [
TxD: The 2nd pin of RS-232, which is in charge of sending data
RxD: The 3rd pin of RS-232, which is in charge of receiving data
]
OFF [
Description
]
]
TxD: The 3rd pin of RS-232, which is in charge of sending data
RxD: The 2nd pin of RS-232, which is in charge of receiving data
Firmware Update
]
Normal
5
IR PASS-THROUGH
IR Extenders
IR Blaster
IR Receiver
IR Sockets
IR BLASTER:plug in the IR blaster to emit all IR command signals received from the IR receiver from
the other enf to control the devices corresponding to the IR signals.
IR RECEIVER:plug in the IR receiver to receive all IR command signals from the IR remote controls of
the corresponding devices.
CAUTION!
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders.
Please check carefully before plugging in the IR extender to the respective IR sockets.
Warranty will not cover the damage.
Definition of IR Earphone Jack
IR Blaster
1. IR Signal [20-60 kHz]
2. Grounding
12
i
6
IR Receiver
1. IR Signal [20-60 kHz]
2. Grounding
3. Power
1 23
You can buy any IR extension cables in the market that are compatible to the definition of
the IR sockets for the matrix if necessary for replacement use. However, IR cables longer
than 2m (6-ft) may not work.
HARDWARE INSTALLATION
1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit of HDM-EXT0107C.
2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit HDM-EXT-0107C-RX.
3. Connect IR Blaster/Receiver to both TX and RX units.
4. Connect USB cable to PC/Laptop
5. Connect a Cat-5/5e/6 cable between the transmitting and receiving units.
6. Make sure this Cat-5/5e/6 cable is tightly connected and not loose.
7. Plug in 24V DC power supply unit to the power jack of the transmitting unit HDM-EXT0107C-TX.
PIN DEFINITION
HDMI
Type A (Receptacle) HDMI
Pin 1
TMDS Data2+
Pin 8
TMDS Data0 Shield
Pin 15
SCL
Pin 2
TMDS Data2 Shield
Pin 9
TMDS Data0–
Pin 16
SDA
Pin 3
TMDS Data2–
Pin 10
TMDS Clock+
Pin 17
DDC/CEC Ground
Pin 4
TMDS Data1+
Pin 11
TMDS Clock Shield
Pin 18
+5V Power
Pin 5
TMDS Data1 Shield
Pin 12
TMDS Clock–
Pin 19
Hot Plug Detect
Pin 6
TMDS Data1–
Pin 13
CEC
Pin 7
TMDS Data0+
Pin 14
Reserved (N.C. on device)
7
NOTICE
1. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e
125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B.
2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders.
Please check carefully before plugging in the IR extender to the respective IR sockets.
Warranty will not cover the damage.
3. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI
sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in
the form of 300m [1,000ft] bulk cables) can transmit a lot longer signals than stranded UTP
cables (usually in the form of fixed length patch cords). Shielded STP cables are better suited
than unshielded UTP cables. A solid UTP Cat-5e cable shows longer transmission range than
stranded STP Cat-6 cable. For long extension applications, solid UTP/STP cables are the
only viable choice.
4. E IA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better
performance.
5. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6
cable, one can use shielded STP cables to improve EMI problems, which is worsen in long
transmission.
6. Because the quality of the CAT5/6 cables has the major effect on how long the transmission
limit can achieve and how good is the received picture quality, the actual transmission range
is subject to one’s choice of Cat-5/5e/6 cables. For desired resolutions greater than 1080i or
1280x1024, a Cat-6 cable is recommended.
7. If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI
input #1] generally can produce better transmission performance among all HDMI inputs.
Performance rating
Wiring
Solid
Stranded
Termination
8
Shielding
Type of category cable
CAT5
CAT5e
CAT6
Unshielded (UTP)



Shielded (STP)



Unshielded (UTP)



Shielded (STP)



Please use EIA/TIA-568-B termination (T568B) at any time
WARRANTY
The SELLER warrants the HDM-EXT-0107C HDMI Extender over Single Cat.X with
HDBasedT free from defects in the material and workmanship for 1 year from the date of
purchase from the SELLER or an authorized dealer. Should this product fail to be in good
working order within 1 year warranty period, The SELLER, at its option, repair or replace
the unit, provided that the unit has not been subjected to accident, disaster, abuse or any
unauthorized modifications including static discharge and power surge. This warranty is offered
by the SELLER for its BUYER with direct transaction only. This warranty is void if the warranty
seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price
of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from
the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure
the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be
accepted without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without
limitations, any other implied warranty or fitness or merchantability for any particular purpose, all
of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are
responsible for shipping charges to and from the SELLER. Cables and power adapters are
limited to a 30 day warranty and must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However,
The SELLER assumes no responsibility for any inaccuracies that may be contained in this
manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential
damages resulting from any defect or omission in this manual, even if advised of the possibility
of such damages. Also, the technical information contained herein regarding the HDM-EXT0107C features and specifications is subject to change without further notice.
9