- Vehicles & accessories
- Motor vehicle accessories & components
- Engine
- Honda
- Outboard Motor BF115A
- Owner's manual
Honda Power Equipment BF5A Boat User Manual 127 Pages
advertisement
▼
Scroll to page 2
of
127
The engine exhaust from this contains chemicals known to of California to cause cancer, defects, or other reproductive product the State birth harm. Keep this owner’s manual handy, so you can refer to it at any time. This owner’s manual is considered a permanent part of the outboard motor and should remain with the outboard motor if resold. The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No part of this publication may be reproduced without written permission, INTRODUCTION Congratulations on your selection of a Honda outboard motor. We are certain you will be pleased with your purchase of one of the finest outboard motors on the market. I We want to help you get the best resuits from your new outboard motor and to operateit safely. This manual contains the information on how to do that; pleaseread it carefully. As you read this manual, you will find information precededby a /mJ symbol. That information is intended to help you avoid damageto your outboard motor, other property, or the environment. We suggestyou read the warranty policy to fully understandits coverage and your responsibilities of ownership. The warranty policy is a separate document that should have been given to you by your dealer. When your outboard motor needs scheduledmaintenance,keep in mind that your Honda marine dealer is specially trained in servicing Honda outboard motors. Your Honda marine dealer is dedicated to your satisfaction and will be pleasedto answer your questions and concerns, 0 1998 Honda Motor Co., Ltd. All Right Reserved 1 INTRODUCTION A FEW WORDS ABOUT SAFETY You will find important safety information a variety of forms, including: l Your safetyandthe safetyof othersarevery important. And using this outboard motor safety is an important responsibility. l To help you make informed decisions about safety, we have provided operating proceduresand other information on labels and in this manual.This information alens you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining an outboard motor.You must useyour own good judgment. Safety Labels -- on the outboard motor. Safety Messages- precededby a safety alert symbol A and one of three signal words, DANGER, WARNING, or CAUTION. These signal word’s mean: You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. l Safety Headings - 9 Safety Section -l Instructions - such as 1MPORTANT SAFETY INFORMATION. such as OUTBOARD MOTOR SAFETY. how to use this outboard motor correctly and safely. This entire book is filled with important safety information - 2 pleaseread it carefully. TYPES OF HONDA BFl15A/l30A OUTBOARD MOTORS It may be necessaryto refer to this chart for referencepurposeswhen reading this manual. I Model Shaft Length L I x Type BFI 15A XA 1 1.r LCA 1 0 1 XA LCA 1 I.1 1. Trimmeter 0 0 0 0 0 0 0 0 0 0 0 0 Tachometer 0 l . XCA PowerTrim/ Tilt l LAbI BF130A StandardRotating~Counterrotating PropellerShaft Propeller Shaft 0 I I I I . . l . I I I I I I I I 101 o--1 .-- -1 TYPE CODE (example) -Destination A: America Rotating direction of propeller shaft C: Counterrotating propeller shaft None: Standardrotating propeller shaft Shaft length L: Long Shaft, X: Extra Long Shaft 3 IDENTIFICATION NUMBERS Record the Product Identification Number (P.I.N.) and the Engine Serial Number for your reference.Refer to the Product Identification Number when ordering parts, and when making technical or warranty inquiries (see page 117). LEFT STERN BRACKET PRODUCT IDENTIFICATION NUMBER The Product Identification Number is stamped on a plate and attached to the left stern bracket. Product identification number: ENGINE SERIAL NbMBER The Engine Serial Number is stamped on the cylinder head on the back of the engine. Engine serial number. CONTENTS I. OUTBOARD MOTOR SAFETY IMPORTANT SAFETYINFORMATION .. 7 SAFETYLABEL LOCATIONS..... 9 2. COMPONENT IDENTIFKATION.. IO 3. CONTROLS & INSTRUMENTS SIDE-MOUNT TYPE RemoteControl Lever ............. I4 Neutral ReleaseLever .,........... I5 Ignition Switch ........................ 15 EmergencyStopSwitchLanyard.. 16 Fast Idle Lever ......................... 17 PGM-FI IndicatorLight/Buzzer... I7 ACG IndicatorLight/Buzzer .... 18 Oil Pressure IndicatorLight/Buzzer .. I8 OverheatIndicatorLight/Buzzer... I 8 Power Trim/Tilt Switch ,.......... I9 PANEL-MOUNT TYPE RemoteControl Lever ............. 20 Neutral ReleaseLever ............. 2 I Ignition Switch ........................ 21 EmergencyStopSwitchLanyard.. 22 Throttle Button .*...................... 23 PGM-FI IndicatorLight/Buzzer.. 23 ACG IndicatorLight/Buzzer .... 23 Oil Pressure IndicatorLight/Buzzer .. 24 OverheatIndicatorLight/Buzzer... 24 Power Trim/Tilt Switch ........... 25 TOP-MOUNT TYPE RemoteControl Lever ............. 26 Ignition Switch ........................ 27 EmergencyStopSwitchLanyard.. 28 Throttle Button ........................ 29 PGM-FI IndicatorLight/Buzzer.. 29 ACG IndicatorLight/Buzzer .... 29 Oil Pressure IndicatorLightiBuuer.. 30 OverheatIndicatorLight/Buzzer... 30 Power Trim/Tilt Switch (remotecontrol lever). 3 I Power Trim/Tilt Switch (control box console).. 31 COMMON PowerTilt Switch (enginepan) .. 32 Trim Meter .......a...................... Tachometer (optionalequipment) .., :; Manual Relief Valve .,.........;... 33 Tilt Lock Lever .......................... 34 Trim Tab .................................. 34 Anodes..................................... Cooling SystemIndicator ......... :: Water Intakes........................... 35 TransomAngle AdjustingRod ... 36 Fuel Cap/Gauge/VentKnob (optional fuel tank) ..... 37 Overrev Limiter ....................... 37 Engine Cover Lock Lever ....... 38 Fuel Hose Connector............... 38 4. PRE-OPERATION CHECKS EngineCoverRemovaVInstallation.. 39 Engine Oil ............................... 40 Fuel Level (optional fuel tank) .. 41 Fuel Recommendations........... 42 OxygenatedFuels .................... 43 Propeller and Cotter Pin .......... 44 Control Lever Friction Adjustment ........................... 45 Engine Cover Lock Lever Adjustment ........................... 46 Other Checks Fuel hose............................... 47 Stem bracket ......................... 47 Tool Kit ................................. 47 Anodes .................................. 47 5. STARTING THE ENGINE Optional Fuel Tank.. ................ 48 Fuel Line Connection .............. 48 STARTING THE ENGINE (SIDE-MOUNT TYPE) .......... 50 (PANEL-MOUNT TYPE) ...... 53 (TOP-MOUNT TYPE). ........... 56 Troubleshooting StartingProblems..59 6. OPERATION Break-in Procedure.................. 60 SIDE-MOUNT TYPE Gear Shifting ............................ Cruising ................................... :: PANEL-MOUNT TYPE Gear Shifting ........................... 63 Cruising ................................... 64 TOP-MOUNT TYPE Gear Shiftinop ........................... 65 5 l l l l CONTENTS Cruising ................................... 66 POWER TRIM/TILT Power Trim/Tilt System.......... 67 Trim Meter .............................. 69 PowerTilt Switch (enginepan) .. 70 Manual Relief Valve ............... 70 Tilt Lock Lever.. ...................... 71 Trim Tab Adjustment.. ............ 72 MOTOR PROTECTION SYSTEM Engine Oil Pressure,Overheat, PGM-FI and ACG Indicator ‘Systems.................................. 73 z;zz; Limiter ....................... 76 ..................................... 76 Shallow Water Operation ........... 77 7. STOPPING THE ENGINE (SIDE-MOUNT TYPE) .......... 78 (PANEL-MOUNT TYPE) ...... 79 (TOP-MOUNT TYPE). ........... 80 8. TRANSPORTING ..................... 81 9. CLEANING AND FLUSHING.. . 84 IO. MAINTENANCE.. .......................86 THE IMPORTANCE OF MAINTENANCE.. .................. 86 MAINTENANCE SAFETY ...... 87 EMISSION CONTROL SYSTEM INFORMATION.. .. 87 Tool Kit and SpareParts ............ 90 MAINTENANCE SCHEDULE.... 91 Engine Oil ............................... 93 6 Oil Filter .................................. 96 GearOil ................................... 98 SparkPlugs.............................. 99 Battery (not included). ........... 100 Lubrication ............................ 102 Engine Fuel Filter.. .................. 103 Fuel Tank and Filter ................ IO5 FuseReplacement................... 106 Propeller ..................................108 SubmergedMotor.. .................. 109 11. STORAGE .................................111 12. TROUBLESHOOTING ............. 114 13. SPECIFICATIONS .................... I 15 14. WARRANTY SERVICE ........... 117 15. INDEX .......................................1I8 16. WIRING DIAGRAM ................. 12I 1. OUTBOARD IMPORTANT SAFETY INFORMATION Operator Responsibility l Honda BFI 15A and BFI 30A outboard motors are designed for use with boats that have a suitable manufacturer’spower recommendation.and other usescan result in injury to the operator or damageto the outboard motor and other property. l Most accidents can be prevented if you follow all instructions in this manual and on the outboard motor. The most common hazardsare discussedbelow, along with the best way to protect yourself and others. l l l It is the operator’s responsibility to provide the necessarysafeguardsto protect people and property. Know how to stop the engine quickly in case of emergency.Understand the use of all controls. l l Stop the engine immediately if anyone falls overboard, and do not run the engine while the boat is near anyone in the water. Always stopthe engineif you mustleave the controls for any reason. Attach the emergencystop switch lanyard securely to the operator. l l l l MOTOR SAFETY Always wear a PFD (PersonalFlotation Device) while on the boat. Familiarize yourself with all and regulations relating to boating and the use of outboard motors. laws Be sure that anyone who operatesthe outboard motor receives proper instruction. Be sure the outboard motor is properly mounted on the boat. Do not remove the engine cover while the engine is running. Do not attempt to modify the outboard motor. Do not remove any labels, covers, or safety devices; they are installed for your safety. 7 1. OUTBOARD MOTOR SAFETY Refuel With Care l l l l Gasoline is extremely flammable, and gasoline vapor can explode. Refuel outdoors, in a well-ventilated area, with the engine stopped.Never smokeneargasoline,and keep other flames and sparks away. Remove any portable fuel tank from the boat for refueling. Keep the portablefuel tank away from the battery or other potential spark sources. Refuel carefully to avoid spilling fuel. Avoid overfilling the fuel tank. After refueling, tighten the filler cap securely.If any fuel is spilled. makesure the ama is dry before starting the engine. Carbon Monoxide Hazard Exhaust gas contains poisonous carbon monoxide.Avoid inhalation of exhaustgas. Neverrun the enginein a closedgarageor confined area. 1. OUTBOARD SAFETY LABEL LOCATIONS Theselabels are in the locations shown. They warn you of potential hazardsthat could seriouslyinjure you. Read theselabelscarefully. MOTOR SAFETY EXTREMELY FmLbE*SrmxmFlEl INFLAMMABLEDANGEREUX GAZOL mm PI Mlw I NE mm WIRE E rlmlrEs~ 9 2. COMPONENT IDENTIFICATION ENGINE COVER OIL LEVEL POWER 1:ILTSWITCH \ ‘r \ - OIL FILLER DIPSTICK \ / CAP FUEL HOSE CONNECTOR , a ENGINE CdVER LOCK LEVER \ -__.__.. ---- _\\ \\ ENGINE OIL DRAIN BOLT. MANUAL VALVE ENGINE 011. ENGINE OIL DRAIN BOLT ACCESS COVER - RELIEr \ . * COOLING SYSTEM INDICATOR ANODE METAL ANODE METAL 1 OIL LEVEL INSPECTION PLUG 10 / rq GEAR OIL DRAIN BOLT WASH PLUG (Flush PLug) EXHAUST PORT WATER INTAKE 2. COMPONENT (SIDE-MOUNT REMOTE POWER CONTROL) (PANEL-MOUNT NEUTRAL RELEASE LEVER TRIM/TILT SWITCH \ REMOTE IDENTIFICATION CONTROL) POWER TRIM/TILT SWITCH / OIL PRESSURE INDICATOR LIGHT OVERHEAT INDICATOR / LIGHT NEUTRAL RELEASE LEVER FAST IDLE LEVER _ EMERGENCY STOP SWITC - vu YLI.LL.*.nN A’)JUSTER m.ll7IBa-mNrP” / Rm.l\” I EME~~GENCY STOP SWITCH SWITCH LANYARD I EMERGENCY STOP SWITCH CLIP 11 2. COMPONENT IDENTIFICATION (SINGLE TOP-MOUNT REMOTE CONTROL) POWER SWITCH (DUAL TOP-MOUNT REMOTE CONTROL) TRIM/TILT POWER TRIM/TILT SWITCH (SIMULTANEOUSCONTROL)‘ . CONTROL LEVER POWER TRIM/TILT SWITCH *(RIGHT INDIVIDUAL ADJUSTMENT) THROTTLE BO’ITON y CONTROL PANEL (for PANEL/TOPMOUNT type) BUZZER OIL PRESSURE INDICATOR LIGHT \ IGNITION SWITCH EMERGENCY STOP SWITCH CLIP \ EMERGENCY 12 - EMERGENCY , SWITCH POWER TRIhl/TILT SWITCH (LEFT INDIVIDUAL ADJUSTMENT) 2. COMPONENT FUEL TANK (Optional IDENTIFICATION METER equipment) VENTKNOB FUELGAUGE / FUEL (option TRIM HOSE CONNECTOR PRIMER METER TACHOMETER (optional equipment) BULB 13 3. CONTROLS (SIDE-MOUNT TYPE) (SIDh-MOUNT TYPE) Remote Control Lever OPENING NEUTRAL RELEASE REMOTE CONTROL LEVER The remote control lever controls gear selection and throttle opening positions. It is necessary to pull up the neutral release lever to operate the remote control lever. F (forward): Moving the lever to the F position (approximately 30” from the N position) will engage the forward gear. Moving the lever farther into the F position will increse the throttle opening and the boat’s forward speed. N (neutral): The engine idles and the transrnission gears are disengaged. 14 R (reverse): Moving the lever to the R position (approximately 3O’from the N position) will engagethe reverse gear. Moving the lever farther into the R position will increase the throttle opening and the boat’s reversespeed. 3. CONTROLS Neutral Release Lever Ignition Switch +- ON START ON II (SIDE-MOUNT TYPE) ON To run the engineafter starting (the battery will dischargeif the key is left in this position with the engine not running). OFF The neutral releaselever is on the remotecontrol lever to prevent an accidentalgear engagement. The remote control box is equipped with a key-type ignition switch. Key positions: The remote control lever will not engageforward or reversegear, unless the neutral releaselever is pulled up. START To stop the engine (IGNITION OFF). To prevent the battery from discharging, keep the key in the OFF position when the engine is not running. To activate the starter motor and start the engine (the remote control lever must be in the neutral position). 15 3. CONTROLS (SIDE-MOUNT Emergency Stop S&h TYPE) Lanyard EMERGENCY E S The emergency stop switch lanyard is provided to stop the engine immediately in the event the operator falls overboard or away from the controls. The emergency stop switch clip must be engaged with the emergencystop switch, or the engine will not start. When the emergency stop switch clip be-comesdisengaged from the emergency stop switch, the engine will stop immediately. 16 SPAREEMERGENCy SmPSWrTCHCLIP ’ The emergencyengine stop switch should not he usedto normally stop the engine.Use the ignition switch to normally stop the engine. Attach the emergencystop switch lanyard securelyto the operatorwhen operating the outboard motor. The lanyard can be attached to the operator’sPFD(personalFlotation Device) or worn around the wrist as shown. A spareemergencystop switch clip is provided on the remotecontrol box. 3. CONTROLS Fast Idle Lever (SIDE-MOUNT TYPE) PGM-FI Indicator Light/Buzzer PGM-FI LIGHT FAST IDLE INDICATOR / OWEST POSITION LE I AEVER The fast idle lever provides fast idle for easy engine start up. . The fast idle lever will not move unless the remote control lever is in the N (neutral) position. Conversely, the remote control lever will not move unless the fast idle lever is in the lowest position. Raise the fast idle lever, and hold it all the way up to provide maximum fast idle. Gradually lower the fast idle lever to the lowest position to decreasethe fast idle. The PGM-FI indicator light turns on and the buzzer sounds when the engine control system is faulty, and when the ignition key is turned from OFF to ON. 17 3. CONTROLS (SIDE-MOUNT ACG Indicator Light/Buzzer TYPE) Oil Pressure Indicator Light/Buzzer Overheat Indicator Light/Buzzer The green oil pressure indicator light turns OFF and the buzzer sounds when the oil level is low and/or the engine lubrication system is faulty. The engine speed slows down gradually- The red overheat indicator light turns ON and the buzzer sounds when there is a cooling system problem. The engine speedslows down gradually. ACG INDICATOR LIGHT The ACG indicator light turns on and the buzzer sounds when the charging system is faulty. The oil pressure indicator light is normally ON while the engine is running. 18 3. CONTROLS (SIDE-MOUNT TYPE) Power Ikimmilt Switch Power Trim Pressthe power trim/tilt switch on the remote control to adjust the motor trim angle from 0’ to 2O’to maintain proper boat trim. The power trim/tilt switch located on the remote control lever can be operated while the boat is under way or while stopped. By using the power trim/tilt switch, the operator can change the trim angle of the motor to achieve maximum boat acceleration, speed,stability and maintain optimum fuel consumption. ANGLE (NOTICE1 Power Tilt Pressthe power trim/tilt swich on the remote control lever to adjust the motor tilt angle from 20” to 72”. By using the power trim/tilt switch, the operator can change the tilt angle of the motor for shallow water operation, beaching, launching from a trailer, or mooring. Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump. 19 3. CONTROLS (PANEL-MOUNT TYPE,) (PANEL-MOUNT TYPE) Remote Control Lever OPENING THROTTI MAXIMUM ’ REMOTE The remote control lever controls gear selectionand throttle opening positions. It is necessaryto pull up the neutral releaselever to operatethe remote con+ lever. F (forward): Moving the lever to the F position (approximately 35” from the N position) will engagethe forward gear. Moving the lever farther into the F position will increse the throttle opening and the boat’s forward speed. N (neutral): The engine idles and the transmission gears are disengaged. I CONTROL LEVER R (reverse): Moving the lever to R position (approximately 35’from the N position) will engage the reverse gear. Moving the lever farther into the R position will increase the throttle opening and the boat’s reverse speed. 3. CONTROLS Ignition Switch Neutral Release Lever START (PANEL-MOUNT TYPE) ON To run the engine after starting (the battery will dischargeif the key is left in this position with the engine not running). OFF RELEASE The neutral releaselever is on the remote control lever to prevent an accidentalgear engagement. The remote control lever will not engage forward or reversegear, unless the neutral release lever is pulled up. The switch panel is equipped with a key-type ignition switch. To stop the engine (IGNITION OFF). To prevent the battery from discharging, keep the key in the OFF position when the engine is not running. Key positions: START To activate the startermotor and start the engine (the remotecontrol lever must be in the neutral position). 21 3. CONTROLS (PANEL-MOUNT TYPE) Emergency Stop Switch Lanyard SPAREEMERGENCY STOPSWITCHCLIP SWITCH CLIP EMERdENCY STOPSWITCH LANYARD The emergency stop switch lanyard is provided to stop the engine immediately in the event the operetor falls overboard or away from the controls. The emergencyengine stop switch should not he usedto normally stop the engine.Use the ignition switch to normally stop the engine. The emergency stop switch clip must be engaged with the emergency stop switch, or the engine will not start. When .the emergencystop switch clip becomesdisengaged from the emergency stop switch, the engine will stop immediately. Attach the emergencystop switch lanyard securelyto the operatorwhen operating the outboardmotor. 22 The lanyard can be attached to the operator’sPFD(personalFlotation Device) or worn around the wrist as shown. A spare emargency switch clip is provided in the tool bag. 3. CONTROLS Throttle Button (Neytral) PGM-FI Indicator Light/Buzzer Backword .* By moving the control lever forward or backward when the throttle button is pushed in, the throttle opening will be increasedwithout engagingthe gears. PGM-FI INDICATOR LIGHT The PGM-FI indicator light turns on and the buzzer soundswhen the engine control system is faulty and when the ignition key is turned from OFF to ON. (PANEL-MOUNT TYPE) ACG Indicator Light/Buzzer ACG 1NDICATOR LIGHT The ACG indicator light turns on and the buzzer soundswhen the charging system is faulty. It is necessaryto position the control lever in N (neutral) to push in the throttle button. 23 3. CONTROLS (PANEL-MOUNT Oil Pressure Indicator Light/Buzzer \ The green oil pressureindicator light turns OFF and the buzzer sounds when the oil level is low and/or the engine lubrication systemis faulty. The engine speedslows down gradual!Y. The oil pressure indicator light is normally ON while the engine is running. 24 TYPE) Overheat Indicator Light/Buzzer \ The red overheat indicator light turns ON and the buzzer sounds when there is a cooling system problem. The engine speed slows down gradually. 3. CONTROLS (PANEL-MOUNT TYPE) Power Trim/Tilt Switch Power Rim Pressthe power trim/tilt switch on the remotecontrol lever to adjust the motor trim angle from 0” to 20” to maintain proper boat trim. The power trim/tilt switch locatedon the remote control lever can be operatedwhile the boat is under way or while stopped. By using the power trim/tilt switch, the operatorcan changethe trim angle of the motor to achievemaximumboat acceleration,speed,stability and maintainoptimum fuel consumption. O” TRIM ANGLE Power Tilt Pressthe power trim/tilt switch on the remotecontrol lever to adjust the motor tilt angle from 20” to 72”. By using the powertrim/tilt switch, the operatorcan changethe tilt angle of the motor for shallow water operation, beaching,launching from a trailer, or mooring. Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump- 25 . 3. CONTROLS (TOP-MOUNT TYPE) (TOP-MOUNT TYPE) Remote Control Lever SINGLE TYPE THROTI’L . .. . . . . . . .. . . . ... MAXIMUM DUAL TYPE REMOTE CONTROL LEVER F (forward): Moving the lever to the F position (approximately 35’ from the N position) will engage the forward gear. Moving the lever farther into the F position will increasethe throttle opening and the boat’s forThe remote control lever controls gear selectionand throttle opening positions. ward speed. N (neutral): The engine idles and the transmis- sion gearsare disengaged. 26 R (reverse): Moving the lever to the R position (approximately 35’ from the N position) will engagethe reverse gear. Moving the lever farther into the R position will increasethe throttle opening and the boat’s reverse speed. 3. CONTROLS Ignition Switch (TOP-MOUNT TYPE) ON To run the engineafter starting (the battery will dischargeif the key is left in this position witi the engine not running). OFF OFF To stop the engine (IGNITION IGNITION ’ SWITCH KEY \ OFF). To prevent the battery from discharging, keep the key in the OFF position when the engine is not running. The switch panel is equipped with a key-type ignition switch. Key positions: START To activatethe startermotor and start the engine(the remotecontrol lever must be in neutral position). 27 3. CONTROLS (TOP-MOUNT TYPE) Emergency Stop Switch Lanyard EMEiGENCY STOP ’ SWITCH CLIP SPARE EMERGE&Y STOP SWITCH CLIP EMERGENCY LANYARD STOP SWITCH The emergencystop switch lanyard is provided to stop the engine immediately in the eventthe operator falls overboard or away from the controls. The emergencyengine stop switch should not be usedto normally stop the engine. Use the ignition switch to normally stop the engine. The emergency stop switch clip must be engaged with the emergency stop switch, or the engine will not start. When the emergency stop switch clip becomesdisengaged from the emergency stop switch, the engine will stop immediately. Attach the emergencystop switch lanyard securelyto the operator when operating the outboard motor. 28 The lanyard can be attached to the operator’sPFD(personalFlotationDevice) or worn around the wrist as shown. A spare emargency switch clip is provided in the tool bag. 3. CONTROLS Throttle Button PGM-FI Indicator Light/Buzzer (TOP-MOUNT TYPE) ACG Indicator Light/Buzzer N (neutral) ACG INDICATOR LIGHT Backward 6 a -+ III By moving the control lever forward or backward when the throttle button is pushed in, the throttle opening will be increased without engaging the gears. The PGM-FI indicator light turns on and the buzzer soundswhen the engine control system is faulty and when the ignition key is turned from OFF to ON. The ACG indicator light turns on and the buzzer soundswhen the charging system is faulty. It is necessaryto position the control lever in N (neutral) to push in the throttle button. 29 3.CONTROLS(TOP-MOUNTTYPE), Oil Pressure Indicator Light/Buzzer The green oil pressureindicator light turns OFF and the buzzer sounds when the oil level is low and/or the engine lubrication systemis faulty. The engine speedslows down graduallyThe oil pressureindicator light is normally ON while the engine is running. 30 Overheat Indicator Light/Buzzer The red overheat indicator light turns ON and the buzzer sounds when there is a cooling system problem. The engine speedslows down gradually. 3. CONTROLS Power Trim/Tilt Switch (remote control lever) Power lkim SINGLETYPE Pressthe power trim/tilt switch on the remote control lever to adjust the motor trim angle from 0’ to 20’ to maintain proper boat trim. The power trim/tilt switch located on the remote control lever can be operatedwhile the boat is under way or while stopped. (TOP-MOUNT TYPE) Power Trim/Tilt Switch (control box console) LEFT INDIVIDUAL ADJUSTMENT By using the power trim/tilt switch, the operator can change the trim angle of the motor to achieve maximum boat acceleration,speed,stability and maintain optimum fuel consumption. RIGHT INDIVIDUAL.ADJUSTMENT Power Tilt Pressthe power trim/tilt switch on the remote control lever to adjust the motor tilt angle from 20“ to 72”. By using the power trim/tilt switch, the operator can changethe tilt angle of the motor for shallow water operation, beaching,launching from a trailer, or mooring. 1NOTICEJ Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump- The right and left outboard motors can be adjusted separately with the switch on the console side. 31 3. CONTROLS (COMMON) Power Tillt Switch (engine pan) Trim Meter Tachometer (optional equipment) TRIM METER TACHOkETER POWER TILT SWITCH The power tilt switch located on the engine pan is for tilting the motor for trailering, or performing outboard maintenance. This power tilt switch should only be operated with the boat stopped and engine off. This switch can operate even when the ignition switch is OFF. 32 The trim meter has a range of 0’ to 20” and indicates the trim angle of the outboard motor. Refer to the trim meter when using the power trim/tilt switch to achieve proper boat performance. The tachometer shows the approximate engine speed in revolutions per minute. Refer to the tachometer when using the power trim/tilt switch to achieve proper boat and engine performance. 3. CONTROLS (COMMON) Manual Relief Valve If the power trim/tilt switch will not tilt the outboard motor, the motor can be manually tilted up or down by opening the manualrelief valve. To tilt the outboard motor manually,turn the manual valve under the left stem bracket no more than 1 or 2 turns counterclockwiseusing a screw driver. MANUAL RELIEF VALVE After tilting the motor, turn the manual relief valve clockwise securely. The manual relief valve must be tightenedsecurelybefore operating the motor or the motor could tilt up when operating in reverse. 33 3. CONTROLS (COMMON) Tilt Lock Lever TREE TILT LOCK LEVER Do not attempt to tilt the outboard motor down while the tilt lock lever is in the lock position. Damage to the power tilt system may occur. Trim Tab TIGHTENING Use the tilt lock lever to hold the motor in the highest tilt position when the boat is moored for a long time. Tilt the motor up as far as it will go. then move the tilt lock lever into the lock position and gently lower the motor. Hitting piers or other boats when the motor is tilted can cause damage. Be especially careful to prevent the boat from bumping anything while the motor is tilted. 34 When making a turn, if an unequal amount of effort is required to turn the steeringwheel right or left, adjust the trim tab so that an equal amount of effort is required. Distribute the load evenly in the boat. and run the boat in straight courseat full throttle. Slightly turn the steering wheel or tiller handle for both right and left turns to determineif an equal amountof effort is required. If adjustment is necessary,loosenthe tightening bolt and turn the trim tab right or left. Make small adjustmentsat a time and retest. Incorrect trim tab adjustmentcan causeadversesteering. The trim tab also functions asan anode. 3. CONTROLS Anodes - Cooling System Indicator (COMMON) Water Intakes ‘\i, . (stern bracket) COOLING SYSTEM INDICATOR The anodesare madefrom a sacrificial material which helps to protect the outboardmotor from corrosion. The cooling systemis monitored here to make surecooling water is circulating through the engine. (NOTICE] Water flowing out of the cooling systemindicator shows that the cooling systemis functioning normally. Painting or coating the anodes will lead to rust and corrosion damage to the outboard motor. (eachside) The engine cooling water is drawn into the water pump through these water intakes. 35 3. CONTROLS (COMMON) TRAN!SOMANGLE ADJUSTING ROD TranSom Angle Adjusting Rod NUT The u&som angleadjustingrod limits the angle of the outboard motor when fully lowered. Propel adjustmentpreventsthe outboard motor from being trimmed too low. .To adjust,first tilt the outboardmotorso it is not restingagainstthe rod. Remove #thenut, then removethe rod and insert it in the desiredposition. Reinstallthe nut and tighten it securely. 36 Start with the transomangle adjusting rod in the hole closestto the boat transom, lower the motor and operatethe boat at full speed.If the bow is excessively low stop the boat.Tilt the motor up and raise the transomangle adjusting rod one more hole away from the transomand retest. The optimum boat him is when the boat is parallel with the water. The motor should never be operated with the transomangle adjusting rod removed. 3. CONTROLS Fuel Cap/Gauge/Vent (optional fuel tank) Knob VENTKNOB Before transporting or storing the fuel tank,turn the vent knob fully clockwise to the closed position. Anytime the fuel tank is in the boat with the vent knob closed, disconnect the fuel hose connector from the outboard motor (refer to page 48). GAUGE FUELFILLERCAP The fuel gauge is part of the fuel cap. The fuel cap vent knob controls air entering and leaving the fuel tank. When refilling the fuel tank, turn the vent knob counterclockwise to the open position and remove the fuel cap, Before transporting, storing or refilling the fuel tank, inspect the condition of the fuel cap gasket and replace if necessary. m Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. 0 Stop engine and keep heat, sparks and flame away. Handle fuel only outdoors. Wipe up spills immediately. (COMMON) Overrev This outboard motor is equipped with an engine overrev limiter which limits the maximum engine rpm. This overrev limiter protects the engine from mechanical damage. The overrev limiter may be activated by putting the propeller in a light load condition or propeller ventilation. When the overrev limiter is activated, the engine rpm will becomeunstable or erratic. Should this occur, reduce the throttle opening and wait for the engine ‘pm to stabilize, then increase the throttle opening. l l Lower the trim angle on high speed to reduce the possibility of propeller ventilation. turns If the overrev limiter activates when trim/tilt angle is correct, stop the engine and check for mounting problems and propeller damage. If mounted improperly, fix it. If the propeller is damaged,replace it. 37 3. CONTROLS (COMMON) Fuel HoseConcctors FUEL HOUSE CONNECTOR (outboard motor) Engine Cover Lock Levers FRONT 0 FREE 1 SIDE I iI -ENGINE COVER ENGINE COVER LOCK LEVER The engine cover lock levers are used to fasten the engine cover. To open and remove the engine cover, turn the front and side lock levers clockwise to the FREE position. To fasten the engine cover, set the engine cover in position and turn the lock levers to the LOCK position. 38 FUEL HOSE CONNECTOR (optional, portable fuel tank) \\ Refer to pages48-49 for fuel hose connection. 4. PRE-OPERATION CHECKS Engine Cover Removal/Installation FRONT 3 .FREE j ENGINE COVER LOCK LEVER ENGiNE COVER LOCK LEVER To remove, turn the front and side engine cover lock levers to the FREE position and remove the engine cover. To install, position the engine cover over the engine and turn the front and side lock levers on the LOCK position. After installing the engine cover, inspect the engine cover fastening condition and adjust it if necessary (page 46). 39 4. PRE-OPERATION Engine CHECKS Oil Engine oil is a major factor affecting engine performanceand service life. Running the engine with insufficient oil can cause serious engine damage. Recommended oil:SAE low-30 or low-40 Use 4-stroke motor oil that meetsor exceedsthe requirements for API service classification SG or SH. Always check the API SERVICE label on the oil container to be sure it includes the letters SG or SH. Using nondetergent oil can shorten the engine’s service life, and using 2-stroke oil can damage the engine. 40 Inspection I _ Position the outboard motor vettitally, and remove the engine cover. 2. Removethe oil level dipstick and wipe with a clean rag. 3. Reinsert the dipstick all the way in, then pull it out .andread the level. If the oil registersnearor below the lower limit mark, remove the oil tiller cap and fill to the upper limit mark with the recommended oil. INoncEJ Do not overfill. Excessive oil can damage the engine. MARK OIL LEVEL DIPSTICK 4. Reinstall the oil filler cap and tighten securely. 5. Install the engine cover and lock it securely. If the engine oil is contaminated or discolored, replace with fresh engine oil (refer to page 93 for oil capacity, replacement interval and procedure). 4. PRE-OPERATION CHECKS Fuel Level (optional fuel tank) VENTKNOB FUEL GliUGE FUELCAP Check the fuel gauge and refill the tank to the SAFE FILL level mark if necessary. Fuel tank capacity : 6.6 US gal. (25 lit) m Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. . Stop engine and keep heat, sparks and flame away. Handle fuel only outdoors. . Wipe up spills immediately. l Refilling Removethe fuel tank from the boat for refilling. l%m the vent knob counterclockwiseto the open position and removethe fuel cap. Refuel in a well-ventilated area.Fill the fuel tank up to the SAFE FILL level.mark only. Inspect the condition of the fuel cap gasketand replace if necessary. After refilling, install and tighten the fuel cap securely.Turn the vent knob clockwise to the closedposition. Return the fuel tank to the boat. 41 4. PRE-OPERATION CHECKS Fuel Recommendations Use unleaded gasoline with a pump octane rating of 86 or higher. These outboard motors are certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. Never use stale or contaminated gasolineor an oil/gasoline mixture. Avoid getting dirt or water in the fuel tank. Occasionally you may hear light “spark knock” or “pinging” (metallic rapping noise) while operating under heavy loads. This is no causefor concern. If spark knock or pinging occurs at a steadyengine speed, under normal load, change brandsof gasoline. If spark knock or pinging persists,seean authorized Honda Marine dealer. IpETiq Running the engine with persistent spark knock or pinging can cause engine damage. Running the engine with persistentspark knock or pinging is misuse,and the Distributor’s Limited Warranty does not cover parts damagedby misuse. 42 4. PRE-OPERATION CHECKS Oxygenated Fuels Someconventional gasolinesare being blendedwith altohol or an ether compound.Thesr gasolinesare collectively referred to as oxygenatedfuels. To meetclean air standards.someareasof the United Statesand Canada useoxygenated fuels to help reduce emissions. If you use an oxygenatedfuel. be sure it is unleadedand meetsthe minimum octanerating requirement. Before using an oxygenatedfuel, try to confirm the fuel’s contents. Somestates/provincesrequire this information to be postedon the pump. The following are the EPA approvedpercentagesof oxygenates: ETHANOL - (ethyl or grain alcohol) 10% by volume You may usegasoline containing up to 10% ethanol by volume. Gasoline containing ethanol may be marketedunder the name“Gasohol”. MTBE - (Methyl Tertiary Butyl Ether) 15%by volume You may usegasoline containing up to 15%MTBE by volume. METHANOL -(methyl or wood alcohol) 5%.by volume You may usegasoline containing up to 5% methanol by volume, as long as it also contains cosolvents and corrosion inhibitors to protect the Fuelsystem. Gasoline containing more than 5% methanol by volume may causestarting and/or performanceproblems. It may also damagemetal, rubber, and plastic parts of your Fuelsystem. If you notice any undesirableoperating symptoms,try another service station. or switch to another brand of gasoline. Fuel systemdamageor perfomlance problems resulting Fromthe useof an oxygenated fuel containing more than the percentagesof oxygenatesmentioned above are not covered under warranty. 43 4. PRE-OPERATION CHECKS Propeller and cotter pin inspection m Thepropellerbladesare thin and sharp. Careless handling of the propeller can result in injury. when checking the propeller: . Remove the clip of the emergency stop switch to prevent accidental engine starting. . Wear heavy gloves when hadling the propeller. The propeller rotates rapidly while cruising. Before starting the engine, check the propeller blades for damageand deformation and replace if necessary. We recommend carrying a sparepropeller and fastening hardwave aboard. If no spare propeller is available, return to the pier at low speed and replace. Consult an authorized Honda outboard motor dealer for propeller selection. COTTER PIN PROPELLEREngine speedvaries according to the propeller size and t.heboat condition. Use of the outboard motor outside the full throttle speed tange will adversely affect the engine and causeserious probblems. Use of the correct propeller assurespowerful acceleration,high top speed,economy and crusing comfort, and it assureslonger engine life as well. Consult with your authorized Honda outboard motor dealer for proper propeller selection. 44 . 1. Check the propeller for damage, wear, or deformation. 2. Check whether the propeller is installed properly. 3. Check the cotter pin for damage. Replace whenever the propeller is replaced. 4. PRE-OPERATION Control Lever Friction Adjustment (SIDE-MOUNT (PANEL-MOUNT CHECKS TYPE) TYPE) ASE FRICTION a‘ ADJUSTER l’n nlWRE,ASE FRICTION I .I ..UV - CONTROL LEVER FRICTION ADJUSTER TO DECREASE FRICTION Move the control lever into forward and (Top MOUNTTYPE) reversegears,and checkthe amountof drag felt. TODECREASE FRICTION Adjust the control lever friction adjuster so that a slight amount of drag is felt. The control lever should move smoothly and freely. FRICTION ADJUSTER 45 4. PRE-OPERATION CHECKS Engine:Cover Lock Lever Adjustment If the engine cover becomesloose, it will shake and become noisy, and it may allow water to enter. Inspect front and rear end individually FF:ONT 3. Adjust if the clerance is outside the specified range. Adjustm.ent 1. Remove the engine cover. Loosen each hook bracket retaining bolt and adjust the height of the brackets to gain the proper clearance. Inspect the engine cover fastening condition and adjust if necessary. Inspection 1. Install the engine cover and fasten with the front and rear lock levers turned to LOCK position. 2. Inspect the clearance between the engine cover and the undercase at the points as shown. Adjust front and rear end individually. HOOK BRACKET /’ INSPECTION POINT \ REAR 0.19 - 0.23 in The clearance should be within 0.19-0.23 in (4.8-5.8 mm). \ \’ 46 I RETAINING BOLT 4. PRE-OPERATION 2. After the adjustment. tighten the bolts securely and install the engine cover. Other Checks //dzJ CHECKS 3 Tool Kit UOS WRENCH &- PLIKRS 0 Reinspect the clearance and readjust if necessary. s mm WRENCH r _ xl FLAT SCREWDRIVER e A PHII.I.IFS SCREWI)RIVER 1 -OIL CHECK SCREWDRIY~R Check the following items: 1. The fuel hosefor kinking, collapsing or loose connections. 2. The stem bracketfor damageand mounting bolts for proper torque. 3. The tool kit contents.Compareyour tool kit contentsagainstthe tool kit illustration above.Replaceany missing items. 4. The anodesfor damage,looseness or excessivecorrosion. The anodeshelp to protect the outboard mot& from corrosion any time they are exposeddirectly to the water. > SCREWDRIVER HANDLE L ” SPARK 9 PLUG WRESCH Replaceanodeswhen they are visibly reduced in size or crumble easily. m Painting or coating the anodes will lead to rust and corrosion damage to the outboard motor. The following materialsshould be kept with the boat: I. Owner’s Manual. 2. Tool Kit. 3. Spareemergencystopswitch clip, engineoil, sparkplugs,propeller, propellernut, washerand cotter pin. 4. Required information regarding boating laws and regulations. 47 5. STARTING THE ENGINE Optional Fuel Tank VENTKNOB The fuel tank must be properly secured in the boat. This will protect the fuel tank from mechanical damagecausedby the fuel tank shifting. The fuel tank must be in a well ventilated area to reduce the chanceof a gasoline vapor explosion. Avoid direct sunlight on the fuel tank. To ensure that the outboard motor will be able to draw fuel from the tank, do not place the fuel tank more than 6 feet away from the motor or lower than 3 feet below the outboard end fuel hose connector. I. Open the fuel tank vent by tuming the vent knob at least 2 or 3 turns counterclockwise. Allow the air pressureinside the fuel tank to equalize with the outside air. With the vent open, air can enter the fuel tank to displacethe fuel as the fuel level goesdown. 2. Removethe fuel cap and inspect the condition of the fuel cap and gasket.Replacethe fuel cap or gasketif they are cracked,damagedor leaking fuel. 3. Check the fuel level. I I I Fuel Line Connection FUEL HOSECONNECTOR (FUEL TANK END)\ Inspectthe fuel hose,and the O-ring sealsin the fuel hoseconnectors. Replace the fuel hose, or fuel hose connectarsif they are cracked.damaged or leaking fuel. Be sure the fuel hose is not kinked. I. Connect the fuel hoseconnector lo the fuel tank. Be sure the fuel hoseconnector is securely snappedin place. 5. STARTING THE ENGINE I FUELHOSECONNECTOR OUTLETEND PRIMERBULB 2. Connect the fuel hose connector to the outboard motor. Install the outboard end fuel hose connector with the clip toward the inside. Be sure the fuel hose connector is securely snapped in place. /JGmq If the outboard end fuel hose connector is forcibly installed in the reversed direction, the fuel hose connector O-ring seal can be damaged. A damaged O-ring seal can cause a fuel leak. m Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel, Stop engine and keep heat, sparks and flame away. Handle fuel only outdoors. Wipe up spills immediately. l l l 3. Hold the primer bulb so that the outlet end is higher than the inlet end. The arrow on the primer bulb points upward. Squeezethe primer bulb several times until it feels firm. indicating that fuel has reached the engine. Check for fuel leaks and repair any leaks before starting the engine. Do not squeezethe primer bulb when the engine is running. 49 5. STARTING THE ENGINE (SIDE-MOUNT TYPE) (SIDE-MOUNT TYPE) EMERGENCY STOP 3 not attach the omeigency stop switch lanyard, and is thrown from his seat olr out of the boat, the out-ofcontrol boat can seriously injure the operator, passengers, or bystanders. CONTRO LEVER Always properly attach the lanyard before starting the engine. EilERCENCYS&P SWrTCHCLIP I. Engage the emergency stop switch clip (located at one end of the emergency stop switch lanyard) with the emergency stop switch. Attach the other end of the emergency stop switch lanyard securely to the operator. 50 The engine will not start unless the emergencystop switch clip is engaged with the emergencyengine stop switch. 2. Move the control lever to the N (neutral) position. The engine will not start unlessthe control lever is in the N (neutral) position. 5. STARTING THE ENGINE (SIDE-MOUNT TYPE) MAXIMUM FAST FASTIDLE LEVER 3. When the engine is cold or the ambient temperatureis low, lift the fast idle lever up fully. 4. Holding the fast idle lever in position, turn the ignition switch key to the START position, and release the key when the engine starts. When the engines is warm, it may be necessaryto raise the fast idle lever slightly. Hold it in this position. The fast idle lever will not move unless the control lever is in the N (neutral) position. j The starter motor consumes a large amount of current. Do not run it continuously for more than 5 secondsat a time. If the enginedoesnot start within 5 seconds, wait at least IO seconds before using the startermotor again. Do not turn the ignition switch key to the start position while the engine is running. This can damage the starter motor and flywheel. 5. After starting the engine, return the lever slowly to a position where the engine does not stall, and hold the lever in that position. The control lever will not move unless the fast idle lever is returned to the lowest position. 51 5. STARTING THE ENGINE (SIDE-MOUNT TYPE) OIL PRESSURE INDICATOR LIGHT 6. After the engine starts,verify water is flowing through the cooling systemby monitoring the cooling systemindicator. The amount of water coming out of the cooling system indicator will vary due to thermostatoperation. Stop . the engine if water does not come out of the cooling system indicator or if you seesteam. Check the water intake screensand the cooling system indicator discharge port, and if necessaryremove any obstructions. If the problem continues, contact your closest authorized Honda Marine dealer. pG5TiEq Running the outboard motor with an obstruction in the cooling system can damage the water pump and overheat the engine. The propeller must remain underwater. Running the outboard motor out of the water will damage the water pump and overheat the engine. l NORMAL:CREEN LIGHT BNORMAL:CREEN LIGHT OR OFF ON BLINK :INC 7. With the engine running, check to see if the green engine oil pressure indicator light turns ON. Stop the engine if the oil pressure indicator light does not turn ON. Check the engine oil level (see page 40). If the oil level is normal and the oil pressure indicator light does not turn ON, contact your closest authorized Honda Marine dealer. 8. Waxm up the engine as follows: Above 41-F (YC) - run the engine for 2 or 3 minutes. Below 41’F (YC) - run the engine for at least IO minutes at approximately2,000 rpm. l 52 Failure to completely warm up the engine will result in poor engine performance. 5. STARTING THE ENGINE (PANEL-MOUNT (PANEL-MOUNT TYPE) If the operator does not attach the emergency stop switch lanyard, and is thrown from his seat or out of the boat, the out-of-control boat can seriously injure the operator, passengers, or bystanders. - EMERGENCY STOP SWITCH CLIP EMERGENCY STOP SWITCH LANYARD 1. Engagethe emergencystop switch clip (located at one end of the emergency stop switch lanyard) with the emergency stop switch. Attach the other end of the emergency stop switch lanyard securely to the operator. TYPE) N (neutral) Always propely attach the lanyard before starting the engine The engine will not start unlessthe emergencystop switch clip is engaged with the emergencyengine stop switch. 2. Move the control lever to the N (neutral) position. The engine will not start unless the gears are not engaged. 53 5. STARTING THE ENGINE (PANEL-MOUNT N (neutral) TYPE) START mm+*: 'L, ..' ,? .y. 1 .... .,., :-,-'.-. :' '.., : ,:' '.,( ;: :;:' .._ ! '.& -. ;:ic : ;;& : -.i i ,,...>._. CONTROL LEVER SWITCH KEY 3. Push the throttle button, then move the control lever forward or backward to open the throttle slightly. \ 4. Turn the ignition switch key to the START position and releasethe key when the engine starts. The starter motor consumes a large amount of current. Do not run it continuously for more that 5 seconds at a time. If the engine does not start within 5 seconds,wait at least 10 seconds before using the starter motor again. 54 (neztrat) .?!k 1NOTICE] Do not turn the ignition switch key to the start position while the engine is running. This can damage the starter motor and flywheel. 5. After starting the engine, return the lever slowly to a position where the engine dose not stall, and hold the lever in that position. ’ The control lever will not shift the gears unless it is first returned to the neutral position. 5. STARTING THE ENGINE (PANEL-MOUNT COOLING WATERINTAKE OIL PRESSURE INDICATOR LlGHT ,. NORMAL:GREENLIGHT ON ABNORMAL:CREEN LIGHT OR OFF 7. After the engine starts,verify water is flowing through the cooling systemby monitoring the cooling systemindicator. The amount of water coming out of the cooling system indicator will vary due to thermostatoperation. Stop the engine if water doesnot comeout of the cooling system indicator or if you seesteam. Check the water intake screensand the cooling system indicator discharge port, and if necessaryremove any obstructions. If the problem continues, contact your closest authorized Honda Marine dealer. l l Running the outboard motor with an obstruction in the cooling system can damage the water pump and overheat the engine. The propeller must remain underwater. Running the outboard motor out of the water will damge the water pump and overheat the engine. TYPE) BLINKING 8. With the engine running, check to seeif the green engine oil pressure indicator light turns ON. Stop the engine if the oil pressure indicator light does not turn ON. Check the engine oil level (seepage40). If the oil level is normal and the oil pressure indicator light does not turn ON, contact your closest authorized Honda Marine dealer. 9. Warmup the engine as follows: Above 41’F (5°C) - run the engine for 2 or 3 minutes. Below 41’F (ST) - run the engine for at least IO minutes at approximately2,000 tpm. Failure to completely warm up the enginewill result in poor engine performance. 55 5. STARTING THE ENGINE (TOP-MOUNT (TOP-MOUNT EMERGENCY TYPE) TYPE) 1. Engagethe emergencystop switch clip (located at one end of the emergency stop switch lanyard) with the emergency stop Atch. N (neutral) Attach the other end of the emergency stop switch lanyard securely to the operator. EMER/CENCYSTOP EMERLENCY STOP SWITCH LANYARD SWITCH CLIP -1 The propeller must remain underwater. Running the outboard motor out of the water will damage the water pbmp and overheat the engine. The following procedure is for starting a single engine equipped with a topmount control. For dulil engines equipped with top mount controls. follow the same steps for each engine. 56 B If the oDerator does not attach the lemeigency stop switch lanyard, and is thrown from his seat or out of the boat, the out-of-control boat can seriously injure the operator, passengers, or bystanders. Always propeiy attach the lanyard before istarting the engine The engine will nor start unless the emergencystop switch clip is engaged with the emergencyengine stop switch. 2. Move the control lever to the N (neutral) position. The engine will not start nuless it is in neutral. 5. STARTING THE ENGINE (TOP-MOUNT N (neutral) 3. Push the throttle button, then move the control lever(s) forward or backward to open the throttle slightly. START TYPE) N (neutral) 4. Turn the ignition switch key to the START position and release the key when the engine starts. The starter motor consumesa large amount of current. Do not run it continuously for more than 5 secondsat a time. If the engine does not start within 5 seconds wait at least 10 seconds before using the startermotor again. Do not turn the ignition switch key to the start position while the engine is running. This can damage the starter motor and flywheel. 5. After starting the engine, return the lever slowly to a position where the engine does not stall, and hold the lever in that position. The control lever will not shift gears unless it is first returned to the neutral position. 57 5. STARTING THE ENGINE (TOP-MOIJNT TYPE) OIL PRESSURE INDICATOR LIGHT I .* WATERINTAKE 7. After the enginestarts, verify water is flowing through the cooling systemby monitoring the cooling systemindicator. The amountof water coming out of the cooling system indicator will vary due to thermostatoperation. Stop the engine if water does not come out of the cooling system indicator or if you seesteam. Check the water intake screensand the cooling system indicator discharge port, and if necessaryremove any obstructions. If the problem continues, contact your closest authorized Honda Marine dealer. piciTi@ Running the outboard motor with an obstruction in the cooliog system can damage the water pump and overheat the engine. The propeller must remain underwater. Running the outboard motor out of the water will damage the water pump and overheat the engine. l l 58 NORMAL: ABNORMAL: GREEN LIGHT GREEN LIGHT OR OFF ON BLINKING 8. With the engine running, check to see if the green engine oil pressure indicator light turns ON. Stop the engine if the oil pressure indicator light does not turn ON. Check the engine oil level (seepage40). If the oil level is normal and the oil pressure indicator light does not turn ON, contact your closest authorized Honda Marine dealer. 9. Warm up the engine as follows: Above 41’F (SC) - run the engine for 2 or 3 minutes. Below 41’F (5°C) -run the engine for at least IO minutes at approximately2,000 rpm. Failure to completely warm up the engine will result in poor engine performance. 5. STARTING THE ENGINE (TROUBLESHOOTING) Throubleshooting Starting Problems SYMPTOM Starter motor doesn’t turn over. POSSIBILE CAUSE REMEDY I. Shift lever not in neutral position. I. Set shift lever in neutral position. 2. Blown 2. Replace fuse. (refer 10 pages 106 and 107) fuse. 3. Weak battery. 3. Charge battery. 4. Faulty battery connections 4. Clean and/or tighten batter) connections. Starter motor turns over but engine will not start. 1. Emergency stop switch clip is not engaged. I. Engage the emergency stop switch clip. (refer to pages 16,22 and 28) 2. Out of fuel. 2. Supply fuel. (refer to page 4 1) 3. Vent knob not open. 3. Open vent knob. (refer to page 48) 4. Primer bulb has not been squeezed. 4. Squeeze primer bulb to supply fuel. (refer to page 49) 5. Engine flooded. 5. Clean and dry spark plugs. (refer to page 99) 59 6. OPERATION Break-in Procedure Break-in period 10 hours Break-in operation allows the moving of full throttle are acceptable. but do not operate the engine continuously at full throttle. parts to wear-in evenly and thus ensuresproper performanceand longer outboard motor life. Break-in your new outboard motor as follows: First 15 minutes: Run the engine at trolling speed. Use the minimum amount of throttle opening necessaryto operate the boat at a safe trolling speed. Next 45 minutes: Run the engine up to a maximum of 2,000 to 3,000 rpm or 10% to 30% throttle opening. Next 60 minutes: Run the engine up to maximum of 4,ooO to 5,000 rpm or 50% to 80% throttle opening. Short bursts 60 Next 8 hours: Avoid continuous full throttle operation (100% throttle opening). Do not run the engine at full throttle for more than 5 minutes at a time. For boats that plane easily, bring the boat up on plane. then reduce the throttle opening to the specified break-in settings called out above. 6. OPERATION (SIDE-MOUNT Gear Shifting TYPE) (SIDE-MOUNT TYPE) N (neutral) I R (reverse) NELJRTAL E&“” II I PULL UP While pulling up the neutral release lever, move the control lever approximately 30’ toward F (forward) or toward R (reverse) to engage the desired gear. Moving the control lever farther forward or backward than 30’ will increase throttle opening and boat speed. The control lever will not move unless the neutral releaselever is pulled up. and the fast idle lever is in the lowest position. 61 6. OPERATION (SIDE-MOUNT TYPE) N Cruising POWER TRImILT SWITCH (neutral) 1 dLd) \n 0 MA I. Press the DN portion of the power trim/tilt switch to tilt the motor to the lowest position. 2. Move the control lever approximately 30” from N (neutral) toward F (forward) to engage the F (forward) gear. 62 Moving the control lever father than 30’ will increase the throttle opening and boat speed. 3. For optimum fuel economy, limit throttle opening to 80%. When cruising at high speed in rough water conditions or large waves, the propeller may not remain fully in the water, and the engine speedcould exceed the maximum speedrange. Slow down to keep the propeller in the water. 6. OPERATION (PANELMOUNT Gear Shifting (PANEL-MOUNT TYPE) TYPE) Avoid sharp and abrupt operation of the control lever. Operate it moderately. Operate the control lever and raise the engine speed after making sure that the gear was shifted securely. (neLi3l) Moving the control lever farther forward or backward than 35’ will increase throttle opening and boat speed. (neC(lral) R The control lever will not move unless the neutral release lever is pulled up. While pulling up the neutral release lever, move the control lever approximately 35” toward F (forward) or toward R (reverse) to engage the desired gear. 63 6. OPERATION (PANEL-MOUNT TYPE) Cruising F (forbard) POWER TRIWILT / I. Press the DN portion of the power trimjtilt switch to tilt the motor to the lowest position. ‘7 ’ LOWEST POSITION 2. Move the control lever approximately 35’ from N (neutral) toward F (forward) to engage the F (forward) gear. N (neutral) Moving the control lever farther than 35’ will increase the throttle opening and boat speed. 3. For optimum fuel economy, limit throttle opening to 80%. When cruising at high speed in rough water conditions or large waves,the propeller may not remain fully in the water, and the engine speedcould exceed the maximum speedrange. Slow down to keep the propeller in the water. 64 6. OPERATION (TOP-MOUNT Gear Shifting SINGLE (TOP-MOUNT TYPE) TYPE) F TYPE N (neutral) N (nertral) R OPENING DUAL TYPE Avoid sharp and abrupt operation of the control lever. Operate it moderately. Operate the control lever and raise the engine speed after making sure that the gear was shifted securely. Move the control lever approximately 35’ toward F (forward) or toward R (reverse) to engage the desired gear. Moving the control lever farther forward or backward than 35’ will increase throttle opening and boat speed. The control lever will not move unless the neutral release lever is pulled up. 6. OPERATION (TOP-MOUNT TYPE) Cruising SINGLE TYPE LEFT MOTOR TRIM/TILT SWITCH I RIGHT MOTOR TRIM/TILT SWITCH POWER TRIM/TILT SWITCH .----- -----MAXIMUM OPENING DUAL TYPE & LOWEST ! POSITION If your boat is dual outboard motor type, adjust the trim angle of the right and left motors to be equal using the switches on the control box, as necessary. I. Press the DN portion of the power trim/tilt switch to tilt the motor lo the lowest position. 66 2. Move the control lever approximately 35’ from N (neutral) toward F (forward) to engage the F (forward) gear. Moving the control lever farther than 35” will increase the throttle opening and boat speed. 3. For optimum fuel economy, limit throttle opening to 80%. When cruising at high speedin rough water conditions or large waves, the propeller may not remain fully in the water, and the engine speedcould exceed the maximum speedrange. Slow down to keep the propeller in the water. 6. OPERATION Power Trim/Tilt System The power trim/tilt systemcan adjust the motor angle while cruising. or the motor tilt angle while mooring. Motor trim angle adjustmentis necessaryto compensatefor boat load or weight distribution, water conditions. propeller or engine condition. The motor trim angle can be adjusted while accelerating or cruising to obtain the maximum boat speed,optimum boat stability, and fuel economy. Under normal conditions, the boat will achieve optimum boat performance when the engine is running at maximum rpm and the ventilation plate is level with the water. (SIDE-MOUNT TYPE) POWERTRIM/TILT SWITCH (POWER TRIM/TILT) (TOP-MOUNT TYPE) SINGLE TYPE POWERTRIM/TILT SWITCH (PANEL-MOUNT TYPE) POWERTRIM/TILT SWITCH DUAL TYPE POWEFfTRIM/TILT SWITCH Presseither the UP or DN portion of the power trim/tilt switch, and trim the motor to the best position for the cruising conditions. The power trim/tilt systemoperates when the switch is pressed,andit stops when the switch is released. 67 6. OPERATION (POWER TRIM/TILT) Dual-Mount Type Power Trim/Tilt Switchs ]NOTICE) Excessive trim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over-revving. Excessive trim/tilt angle can also damage the water pump and overheat the engine. LEFT INDIVIDUAL ADJUSTMENT 72” To trim motor up slightly, press the UP portion momentarily. To trim motor down slightly, press the DN portion momentarily. Decreasethe trim angle on high speed turns to reduce the possibility of propeller ventilation. Improper motor trim angle can result in an unstable steering condition. 68 TRIM ANGLE RIGHT INDlVIDUAi ADJUSTMENT The right and left outboard motors can be adjusted separately with the individual adjustment switch on the console side. 6. OPERATION MOTOR TRIMMED TOO LOW MOTOR TRIMMED TOO HIGH ‘Ikim Meter The trim meter indicatesthe trim angle of the motor. Refer to the trim meter,and pressthe UP or DN portion of the power trim/tilt switch to adjust.the motor trim angle to achievegood boat performanceand stability. BOW TOO LOW DUE TO 1. LOAD IN THE FRONT 2. MOTOR TRIMMED TOO LOW ROUGH WAVES (POWER TRIM/TILT) BOW TOO HIGH DUE TO 1. LOAD IN THE REAR 2. MOTOR TRIMMED TOO HIGH MOTOR TRIMMED CORREQXY When cruising: (A) Into a high wind, trim the motor down slightly to levelthe bow and improveboat stability. (B) With a tail wind, trim the motor up slightly to raise the bow and improve boat stability. With the motor trimmed low, the trim meter will read as shown. To raise the bow, increase the motor trim angle by pressing the UP portion of the power trim/tilt switch. With the motor trimmed high, the trim meter will read as shown. To lower the bow, decreasethe motor trim angle by pressing the DN portion of the power trim/tilt switch. (C) Through rough waves,do not trim the motor too low or too high to avoid an unstablesteering condition. 69 6. OPERATION (POWER TRIM/TILT) Power Tilt Switch (Engine Pan) Manual Relief Valve MANUAL POWER’TILT SWITCH The power tilt switch located on the engine’pan is a convenience switch for tilting the motor for trailering, or performing outboard motor maintenance. This power tilt switch should only be operated when the boat is stopped and the engine is off. 70 If the power trim/tilt switch will not tilt the outboard motor, the motor can be manually tilted up or down by operating the manual relief valve. To tilt the outboard motor manually,turn the manualrelief valve under the left stem bracketno more than laor 2 turns counterclockwise, using a screwdriver. After tilting the motor. turn the manual relief valve clockwise securely. The manual relief valve must be tightened securely before operating the motor. or the motor could tilt up when operating in reverse. 6. OPERATION (POWER TRIM/TILT) TILT LOCK TILT LOCK LEVER Tilt Lock Lever Use the tilt lock lever when the boat is moored. 1. Xlt the motor up as far as it will go using the power trim/tilt switch. 2. Move the tilt lock lever to the LOCK position, and lower the outboard motor until1 the lock lever contacts the stern bracket (refer to page 34). It may be necessary to lift the engine cover grip slightly to swing the tilt lock lever into the LOCK position. 3. To lower the motor, tilt the motor up slightly, movethe tilt lock lever to the FREE position, and lower the motor to the desired position. 71 6. OPERATION Trim Tab Adjustment TIGHTENING BOLT The trim tab is provided to adjust for “torque steer” which is a reaction of the propeller rotation or propeller torque. If during a high speed turn, an unequal amount of effort is required to turn the boat right or left, adjust the trim tab so that an equal amount of effort is required. Distribute the load evenly in the boat, and run the boat in a straightcourseat full throttle. Slightly turn the steering wheel for both right and left turns to determine the amount of effort required. 72 If lesseffort is required to make left tUR1s: Loosen the trim tab tightening bolt, and turn the rear end of the trim tab toward the left Tighten the bolt securely. If lesseffort is required to makeright turns: Loosen the trim tab tightening bolt, and turn the rear end of the trim tab toward the right. ‘Iighten the bolt securely. Make small adjustmentsat a time and retest. Incorrect trim tab adjustment can causeadversesteering. 6. OPERATION (MOTOR PROTECTION Engine Oil Pressure, Overheat, PGM-FI, ACG Indicator Systems SYSTEM) OIL PRESSURE If the engine oil pressuredrops and/or the engine overheats,either or both indicator systemscould be activated. When activated, the engine speed will decreasegradually, the green oil pressureindicator light may turn OFF, and the red overheat indicator light may turn ON (seepage 74). A continuous buzzer will sound. OVERHEAT ACG INDICATOR LIGHT The engine speedcan not be increased with a larger throttle opening until the malfunction is corrected. When the malfunction is corrected, the engine speedwill increasegradually. On Each of the PGM-FI, ACG, oil pressure, andoverheatindicator systemsis activated as described in the following table. 0 O e Q 0 PGM-FI LIGHT INDICATOR 73 6. OPERATION T (MOTOR PROTECTION SYSTEM) 6. OPERATION (MOTOR PROTECTION If the engine is turned off after running at full throttle, the engine temperaturemay rise above normal, If the engine is restated,shortly after being turned off, the overheat indicator system could be activated momentarily. When the oil pressure warning systems is activated: 1. Stop the engine immediately and check the engine oil level (refer to page 40). 2. If the oil is up to the recommended level, restart the engine. If the oil pressure indicator system stops after 30 seconds,the system is normal. If the throttle was closed suddenly after cruising at full throttle, the engine speedmay drop below the specified idle speed.This could cause the oil pressureindicator system to activate momentarily. 3. If the oil pressure indicator system stays activated after 30 seconds, return to the closest boat landing. and contact your closest authorized Honda Marine dealer. SYSTEM) COOLING SYSTEM iNDICATOR When the overheat indicator system is activated: I. Return the gearshift lever or control lever to the N (neutral) position immediately. Check to seeif water is flowing out of the cooling system indicator. 3. If the overheat indicator system stays activated, stop the engine, tilt up the motor and check the water intakes for obstructions. If there are no obstructions at the water intakes, return to the closest boat landing, and contact your closest authorized Honda Marine dealer. 2. If water is flowing out of the cooling system indicator, continue idling for 30 seconds.If the overheat indicator system stops after 30 seconds,the system is normal. 75 6.OtiERATION (MOTOR PROTECTIO:N SYSTEM) When the PGM-FI indicator system is activated. I. Consult with an authorized Honda outboard motor dealer. When the ACG indicator system is activated. 1. Check the battery. If the battery is OK, consult with an authorized Honda outboard motor dealer. Overrev Limiter This outboard motor is equipped with an engine overrev limiter which activates when the engine speed increases excessively. The overrev limiter can be activated while cruising, tilting up the motor, or when ventilation occurs during a sharp turn. Anodes (stern bracket) When the overrev Iimiter is activated: I. Reduce the throl.tle opening immediately and check the trim angle. 2. If the trim angle is correct but the overrev limiter stays activated, stop the engine, check the condition of the outboard motor, and check the propeller for damage.Correct or service as necessary. ‘- (each side) The anodes are a sacrificial material which helps to protect the outboard motor from corrosion. 1NOTICE] Painting or coating the anodes will lead to rust and corrosion damage to the outboard motor. There are also 2 small sacrificial anodes in the water passagesof the engine block. 76 6. OPERATION Shallow Water Operation Excessivetrim/tilt angle during operation can cause the propeller to raise out of the water and cause propeller ventilation and engine over revving. Excessive trim/tilt angle can also damage the water pump and overheat the engine. When operating in shallow water, tilt the motor up to preventthe propeller and gear casefrom hitting the bottom With the motor tilted up, operate the engine at low speed. Monitor the cooling systemindicator for water discharge.Be sure that the motor is not tilted so high that the water intakesare out of the water. 77 7. STOPPING THE ENGINE (SIDE-MOUNT (SIDE-MOUNT TYPE) Emergency Engine Stop EMERGENCY STOP SWITCH TYPE) Normal Engine Stop N (neutral) EMERGENCY STOP SWITCH LANYARD IGNITION EMERGENCY STOP SWITCH CLIP Disengage the emergencystop switch clip from the emergencystop switch by pulling the emergencystop switch lanyard. It is a good idea to stop the engine with the emergencystop switch lanyard from time to time to be sure that the switch is operating properly. 78 KEY I. Move the control lever to the N (neutral) position, and turn the ignition key to the OFF position. 2. When the boat is not in use, remove and store the ignition key. 7. STOPPING THE ENGINE (PANEL-MOUNT (PANEL-MOUNT TYPE) Emergency Engine Stop CONTROL PANEL TYPE) Normal Engine Stop N(neutral) ERGENCY STOP ITCH LANYARD EMERCENCY STOP SWITCH CLIP Disengage the emergency stop switch clip from the emergencystop switch by pulling the emergency stop switch lanyard. 1. Move the control lever to the N (neutral) position, and turn the ignition key to the OFF position. 2. When the boat is not in use,remove and store the ignition key. It is a good idea to stop the engine with the emergencystop switch lanyard from time to time to be sure that the switch is operating properly. 79 7. STOPPING THE ENGINE (TOP-MOIJNT Normal Engine Stop (TOP-MOUNT TYPE) Emergency Engine Stop EMERGENCY STOP SWITCH CONTROL TYPE) N(neutral) PANEL OFF EMERGENCY STOP SElTCH LANYARD IGNITION EMERGENCY STOP SWITCH KEY \ CLIP Disengage the emergency stop switch clip(s) from the emergency stop switch(es) by pulling the emergency stop switch lanyard(s). It is a good idea to stop the engine(s) with the emergencystop switch lanyard(s) from time to time to be sure that the switch(es) is(are) operating properly. I. (SINGLE TOP-MOUNT TYPE) Move the control lever to the N (neutral) position, and turn the ignition key to the OFF position. (DUAL TOP-MOUNT TYPE) Move both control levers simulteneously to the N (neutral) position, and turn each ignition key to the OFF position. 2. When the boat is not in use, remove and store the ignition switch key(s). 8. TRANSPORTING Before transporting the outboard motor, close the fuel cap vent knob (refer to page 37) and disconnect the fuel coupling from the outboard motor (refer to page 49). Trailering When trailering or transporting the boat with the motor attached, it is recommended that the motor remain in the normal run position. Use a motor support bar (refer to your motor support bar manufacturer’s instructions) to stop the motor’s sideto-side movement. If there is insufficient road clearance with the motor in the normal run position, then trailer the motor in the tilted position using a motor support bar (refer to your motor support bar manufacturer’s instructions) or remove the motor from the boat. 81 8. TRANSPORTING Transporting on a vehicle LIFTING EYE HOIST HOOK When transporting the outboard motor on a vehicle, perform following. I. Remove the engine cover. OUTBOARD MOTOR STAND 2. Hook a hoist hook to the liftingeye, and lift the motor from the boat. 3. Place the motor on an outboard motor stand and secure with bolts and nuts. 4. Reinstall the engine cover. a2 8. TRANSPORTING Horizontal Transport Before removing the motor from the boat, drain the vapor separatorand engine oil. Follow the vapor separator drain procedure on page I I 1. PROtECTOR Always rest the motor on protectors and be sure to protect, it from inpact and damage. 83 9. CLEANING AND FLUSHING WATERHOSEADAPTER FLUSH1 CONNE Thoroughly clean and flush the outboard motor with fresh water after operation in dirty or salty water. Flushing with the water hose adapter (optional equipment) Do not run the engine dunng this flushing procedure. For safety.remove the emergency stop switch clip, so the engine cannot be started while you are standing near the propeller. I. Remove the flush port cap. 84 2. Install the water hose adapter(optional equipment) in the flushing connector. 3. Connect a water hose to the water hose adapter(optional equipment), and turn on the water supply. 9. CLEANING AND FLUSHING 4. Make sure that the water comes out from the exhaust port. 5. After flushing, remove the water hose adapter (optional equipment) and reinstall the hose flush port cap. 85 10. MAINTENANCE THE IMPORTANCE OF MAINTENANCE Good maintenanceis essential for safe, economical, and trouble-free operation. It will also help reduce pollution. m Improperly maintaining this outboard motor, or failure to correct a problem before operation, can cause a malfunction in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommen dations and schedules in this owner’s manual. To help,you properly care for your outboard motor, the following pages include a maintenanceschedule, routine inspection procedures, and simple maintenanceprocedures using basic hand tools. Other service tasks that are more difficult, or require special tools, are best handled by 86 professionals and are normally performed by a Honda technician or other qualified mechanic. The maintenanceschedule applies to normal operating conditions. If you operate your outboard motor under unusual conditions, consult your servicing dealer for recommendations applicable to your individual needs and use. Remember that your authorized Honda marine dealer knows your outboard motor best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, USConly new, genuine Honda parts or their equivalents for repair and replacement. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine engine repair establishment or individual, using parts that are “certified” to EPA standards. 10. MAINTENANCE MAINTENANCE SAFETY Some of the most important sefety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance.Only you can decide whether or not you should perform a given task. Safety Precautions l Make sure the engine is off before you begin any maintenanceor repairs. This will eliminate several potential hazards: - Carbon monoxide poisoning From engine exhaust. Be sure there is adequateventilation whenever you operatethe engine. m, .= Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. - Burns from hot parts. Let the engine cool before touching. Always follow the procedures and precautions in this owner’s manual. - Injury From moving parts. Do not run the engine unless instructed to do so. l Read the instructions before you begin, and make sure you have the tools and skills required, l To reduce the possibility of fire or explosion, be careful when working around gasoline. Use only a nonflammable solvent, not gasoline to clean parts. Keep cigarettes, sparks, and flames away from all fuelrelated parts. EMISSION CONTROL SYSTEM INFORMATION Source of Emissions The combustion processproduces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because,under certain conditions, they react to form photochemical smog when subjectedto sunlight. Honda utilizes lean PGM-FI and other systemsto reduce the emissions of oxides of nitrogen and hydrocarbons. 87 10. MAINTENANCE The U; S. Clean Air Act Problems That May Affect Emissions EPA regulations require all manufactures to furnish written instructions describing the operation and maintenance of emission control systems. If you are aware of any of the following symptoms, have your engine inspected and repaired by your servicing dealer. The following instructions and procedures must be followed in order to keep the emissions from your Honda engine within the emission standards. l Hard starting or stalling after starting. l Rough idle. l Misfiring or backfiring under load. l Afterburning (backfiring). Tampering and Altering Tampering with or altering the emission control system may increase emissions beyond the legal limit. Among those acts that constitute tampering are: l l Removal or alteration of any part of the intake, fuel,, or exhaust systems. Alterations that would causethe engine to operate outside its design parameters. 88 l Black exhaust smoke or high fuel consumption. 10. MAINTENANCE Replacement Parts Maintenance The emission control systemson your Honda engine were designed, built, and certified to conform with EPA emission regulations. We recommend the use of genuine Honda parts whenever you have maintenancedone. These original-design replacement parts are manufactured to the same standardsas the original parts, so you can be confident of their performance. The use of replacement parts that are not of the original design and quality may impair the effectiveness of your emission control system. Follow the maintenanceschedule on pages91 and 92. Remenberthat this schedule is basedon the assumption that your machine will be usedfor its designed purpose. Sustainedhigh-load or hightemperatureoperation, or use in unusually wet or dusty conditions, will require more frequent service. A manufacturerof an aftermarket part assumesthe responsibility that the part will not adversely affect emission performance.The manufacturer or rebuilder of the part must certify that use of the part will not result in a failure of the engine to comply with emission regulations. 89 10. MAINTENANCE Tool Kit and Spare Parts TOOL KIT The following tools and spare parts are supplied with the outboard motor for maintenance,adjustment,and emergency repairs. 14 x 17 mm WRENCH a== BOX WRENCH 10 x 12 mm WRENCH ‘) PLIERS 8 mm WRENCH c CD FLAT SCREWDRIVER D SCREWDRIVER 3 HANDLE ED PHILLIPS OIL CHECK TOOL BAG SCREWDRIVER SCREWDHIVER SPARK PLUG WRENCH SPARE EMERGENCY STOP SWITCH CLIP 10. MAINTENANCE MAINTENANCE REGULAR ITEM 0 SCHEDULE SERVICE PERIOD (3) Perform at every indicated month or poerating hour intervals, whichever comes first. Engine oil Check level EACH USE 0 Check level and check for water contamination Engine oil filter Change Engine timing belt Check-readjust EVERY 200 HRS OR YEAR EVERY 400 HRS OR 2 YEARS 0 0 O(2) Change l EVERY IOOHRS OR 6 MONTHS 0 Change Gear case oil FIRST 20 HRS OR MONTH O(2) 0 00) Balancer belt ACG belt Check O(2) O(2) and idling speed Adjust O(2) O(2) 0 Valve clearance Check-readjust O(2) O(2) 0 Spark plugs Check-adjust (Replace if neccessary) 0 0 Propeller Check Throttle linkage and cotter pin 0 0 (Replace if neccessary) Lubrication Grease O(l) O(I) 91 10. MAINTENANCE l Emission-related items (I) Lubricate more frequently when used in salt water. (2) These items should be serviced by an authorizedHonda Marine dealer, unless the owner has the proper tools and is mechanically proficient. Seethe Honda Shop Manual. (3) For professional commercial use, log hours of operation to determineproper maintenanceintervals. 92 10. MAINTENANCE Engine Oil Engine oil is a major factor affecting engine performance,servicelife, and emission. Oil check interval: Each use. Oil change interval: After the first 20 hours or 1 month, then every 100 hours or 6 months. (Refer to the maintenance schedule pages91). Oil capacity: 5.9 US qt (5.6 lit) ... When oil filter is not replaced 6.2 US qt (6.5 lit) ... When oil filter is replaced Recommended oil: SAE low-30 or low-40 Use 4-stroke motor oil that meetsor exceedsthe requirements for API service classification SG or SH. Always check the API SERVlCE label on the oil container to be sure it includes the letters SG or SH. UPP LIM LOW LIMI / 1NOTICE] Using nondetergent oil can shorten the engine’s service life, and using 2-stroke oil can damage the engine. ; .’ OIL LEVEL DIPSTICK Engine Oil Check Check the engine oil level with the engine stopped and the outboard motor in the vertical position. 1. Remove the engine cover. 2. Pull out the dipstick and wipe off. 3. Reinsert the dipstick and pull out again to check the level. If the level is near the lower limit. refill to the upper limit. If the oil is dirty, replace it. If water is contaminated (it becomeswhite as milk), see your authorized Honda marine dealer. 93 10. MAINTENANCE OIL FILLER CAP DRAIN PLUG / SCREW I WASHER I DR$IN PLUG GUIDE COVER Engine Oil Change Drain the oil while the engine is still warm to assure rapid and complete draining. 1. Position the outboard motor vertically, and remove the engine cover. Remove the oil filler cap. 2. Remove the drain plug cover screw using a flat blade:screwdriver, and remove the drain plug cover. 3. Place a suitable container under the guide. Remove the engine oil drain plug and washer using a 12 mm wrench, and drain the engine oil. 4. Install a new sealing washer on the drain plug and tighten the drain plug securely. 5. Reinstall the drain plug cover. 6. Fill with the recommendedengine oil (P. 93) 94 10. MAINTENANCE 8. Reinstall the oil filler cap and tighten securely. UPPER LIMIT LOWER LIMIT 7. Inspect the engine oil level and refill to the upper limit mark on the oil level dipstick if necessary. Fill with the recommended oil. Always wash your handsafter handling usedoil. Improper disposal of engine oil can be harmful to the environment. If you change your own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground. NOTE: To avoid incorrect gauging of the engine oil level, inspect the oil level when the engine has cooled. The outboard motor needsto be in the vertical position. 95 lO.MAINTENANCE OIL FILTER CHANGE 1. Drain the engine oil, and reinstall the drain plug and drain plug cover (see EA’GINE OIL CHANGE, p.94). OIL FILTER OIL FILTER SOCKET (commerciallyavailable) I. .. / 2. Tilt the outboard motor, and place a suitable container below the oil drain guide to catch the used oil 3. Use an oil filter socket tool or an oil filter strap wrench to remove the oil filter, and thoroughly drain the filter into the used oil container. 4. Clean the oil filter mounting base,and coat the gasketof the new oil filter with clean engine oil. Use only a genuine Honda oil filter or a filter of equivalent quality specified for your model. Using the wrong filter, or a non-honda filter which is not of equivalent quality, may cause engine damage. 5. Screw on the new filter by hand until it contacts the engine, then use an oil filter socket tool or an oil filter strap wrench to tighten the filter an additional 7/8 tom. Oil filter tightening torque: I6 ft-lb (22 N*m, 2.2 kg-m). 6. Return the outboard motor to the vertical position, and fill the crankcase with the specified amount (p. 93) of the recommendedoil. GASKET 96 10. MAINTENANCE 7. Start the engine, and check for leaks. Running the engine without water can cause serious engine damage. If you are changing the oil filter while the outboard motor is out of the water, use the water hose adapter (optional equipment) and a hose (p. 84) to supply water. 8. Stop the engine, and check the oil level as described on page 93. If necessary,add oil to bring the oil level to the upper limit mark on the dipstick. 97 10. MAINTENANCE Gear Oil Oil check interval: Every 6 months or 100 hours. GEAR OIL CHECK PLUG Oil change interval: After the first 20 hours or 1 month, then every 200 hours or 1 year. (Refer to the maintenanceschedulepage 91). Oil CAPACITY: 33.8 fl oz. (I .Olit) Recommended oil: SAE, #90 Hypoid gear oil or equivalent, API Service Classification (GL-4 or GL5). DRAIN Gear Oil Level Check 1. Position the outboard motor vertically. 2. Remove the level plug and see if oil flows out. 3. Install and tighten the check plug securely. If there is water in the oil, the water will flow out first when the drain screw is removed, or the oil will be a milky color. Consult with an authorized Honda outboard motor dealer. 10. MAINTENANCE Spark Plugs To ensureproper engine operation,the spark plugs must be properly gapped and free of deposits. 17 mm WRENCH 0.028-0.031 in (0.7-0.8 mm) Check-replace interval: After the first 20 hours or I month then every 200 hours or 1 year (Refer to the maintenanceschedule page 91). Recommended spark plug: ZFR7F (NGK), KJ22CR-L8 (DENSO) Use only the recommendedspark plugs or equivalent. -1 Spark plugs which have an improper heat range may cause engine damage. I. Allow the engine to cool. The spark plugs will be hot if the engine has been running. 2. Remove the engine cover. WRENCH 3. Disconnectthe sparkplug caps from the spark plugs. 4. Use the spark plug wrench and I7 mm wrench supplied in the tool kit to remove the spark plugs. 6. Measurethe plug gapswith a spark plug gap gauge. The gaps should be 0.028-0.03I in (0.7-0.8 mm). Correct as necessary by carefully bendingthe side electrode. 5. Checkthe sparkplugs. Replacethe sparkplugs if there is apparent wear, or if the insulatorsare crackedor chipped. Clean the spark plugs with a wire brush if they are to be reused. 99 10. MAINTENANCE Battery (not included) Minimum requirements 12V-80AHmarine battery. 7. Thread the plugs in by hand to prevent crossthreading. 8. After the spark plugs are seated, tighten with a spark plug wrench and I7 mm wrench to compress the washers. If installing new spark plugs, tighten l/2 turn after the spark plugs seat to compress the washers. If reinstlling used spark plugs, tighten l/81/4 turn after the spark plugs Seat to compress the washers. CYLINDER 4’ 9. Reinstall the spark plug caps, matching the numbers on the cords with the cylinder numbers, as shown. The spark plugs must be securely tightened. A loose spark plug can become very hot and may cause engine damage. Overtightening the spark plugs cam1damage the threads. 100 10. MAINTENANCE To protect the battery from mechanical damageand to prevent the battery from falling or tipping over, the battery must be: l Installed in the correct size corrosion-resistantbattery box. 4. Put the cover on the battery box, and securethe battery box to the boat. Properly securedin the boat. l Securedin a location free from direct sunlight and water spray. l l Securedaway from the fuel tank to avoid potential sparksnear the fuel tank. 1. Install the battery in the battery box. 2. Connect the positive (+) battery cable first, then connect the negative (-) battery cable. Tighten the cable nuts securely. 3. Coat the battery terminals and cable ends with marine anticorrosion grease. 101 THROTTLE Lubrication Lubrication interval: After the first 20 hours or 1 month, then every 100 hours or 6 months. (Refer to the maintenance schedule page 91). Apply marine anticorrosion greaseto the following parts. SHIFT SHAFT TRANSOM ANGLE ADJUSTING ROD/ SWIVEL CASE I 102 REEL THROTTLE AR IIFT ARM SH!!i& 10. MAINTENANCE Engine Fuel Filter Change interval: Every 400 hoursor 2 years CONNECTOR FUEL HOSE (Refer to the maintenanceschedule page 92). FUEL FILTER The engine fuel filter is locatedunder the engine cover betweenthe fuel coupling and the fuel pump. Wateror sedimentaccumulatedin the fuel filter can causeloss of power or hard starting. Always work in a well-ventilated area. Make sure that any fuel drained from the outboard motor is storedin an approvedgasolinecontainer. Be careful not to spill any fuel when replacing the fflter. Spilled fuel or fuel vapor may ignite. If any fuel is spilled, make sure the area is dry before starting the engine. m Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Check interval: Every 100 hours or 6 months (Refer to the maintenance schedule page 92). l Check 1. Removethe engine cover and disconnectthe fuel hose connector from the outboard motor. Stop engine and keep heat, sparks, and flame away. l Handle fuel only outdoors. l Wipe up spills immediately. 103 10. MAINTENANCE FUE:LHOSECLAMPS FUEL FILTER \ SPRING RETAINR 2. Pull the spring retainer toward you, and raise the fuel filter. 3. Check the fuel filter for water accumulation or sediment. If no water or sediment are found, reinstall the fuel filler properly. FUEL HOSES Change 1. Remove the fuel filter. Before removing the fuel filter, to prevent fuel leakage,place fuel hose clamps on the fuel hosesat eachside of the fuel filter. FUEL FILTER ARROW (Fuel Flow Direction) 2. Install the new fuel filter so the arrow on the fuel filter points toward the fuel pump. Fuel flow will be reducedif the fuel filter is installed backward. 3. Connect the fuel hosesto the fuel filter securelywith the hose clips. Remove the fuel hose clamps used to close the fuel hoses. 104 10. MAINTENANCE 4. Securely connect the fuel hose connector to the outboard motor (refer to page 46). Fuel Tank and Filter (optional equipment) Fuel Tank Cleaning 1. Disconnectthe fuel hosefrom the fuel tank. 5. Prime the engine using the primer bulb (refer to page 49). Check for fuel leaks. Repair any fuel leaks if necessary. If loss of power or hard starting are found to be causedby excessivewater or sedimentaccumulation in the fuel filter. inspect the fuel tank. Clean the fuel tank and tank filter if necessary.It may be necessaryto drain the fuel tank completely and refill with fresh gasoline. Gasoline is highly flammable and explosive, and you can be burned or seriously injured when handling fuel. l Stop engine and keep heat, sparks, and flame away. Cleaning interval: Every 200 hours (Refer to the maintenanceschedulepage 92). l l Inspect the condition of the fuel cap gasket, fuel hose, and the O-ring seals in the fuel hose connectors. Replace the fuel cap gasket,hose,or fuel connectorsif they are cracked,damaged or leaking fuel. Be surethe fuel hose is not kinked. Handle Wipe fuel only outdoors. up spills immediately. 2. Empty the gasolinefrom the fuel tank into an approvedgasolinecontainer. Pour in a small quantity of fresh gasoline,and clean the tauk thoroughly. Drain and disposeof the gasolineproperly. 105 10. MAINTENANCE Fuse Replacement FUELTANKHOSE CONNECTOR MAIN FUSE FUSECOVER BLOWNFUSE Fuel Tank Filter Cleaning/Replacement II‘ the fuse is blown, running the engine will not charge the battery, and the electric starter will not work. 1. Turn the fuel tank hoseconnector counterclockwiseto removethe fuel tank filter. FUSE RATING: MAIN IOA, 30A ACG 90A Replacement 2. Clean the fuel tank filter with nonflammable cleaneror solvent. Replacethe fuel tank filter if necessary. Replacing a fuse with one that bas a 2. Remove the engine cover. higher rating greatly increases the chances of damaging the electrical system. 3. Pull the blown fuse out of the clip. If you do not have a replacement fuse with the prolper rating for the circuit, install one with a lower rating. Spare fuses are located in each fuse holder. 3. After cleaning or replacement,reinstall the fuel tank filter and fuel tank hoseconnector securely. 106 4 SPAR-EFUSE (IOA, 30A) 1. Stop the engine. 4. Push a new fuse into the clip. 10. MAINTENANCE ACGFUSE "90A" MARK FUSECASELID h 3. Remove the fuse cast lid. 4. Remove the old fuse by removing two 5 mm screws. 5. Install a new fuse with the “90A” mark downward. FUSE(90A) USE 6. After finishing replacement,install the fuse case lid with its hook toward the engine side. 7. Be sure to check the fuse case lid is securely locked. Disconnect the battery cable at the battery negative (-) terminal before replacing the fuse. Failure to do so may cause a short circuit. Replacement A sparefuse is locatedon the reverseside of the fuse caselid and tightenedwith two 3 mm screws. When the new fuse is set as a spare fuse on the reverseside of the fusecaselid, set the fuse so that you can see the “90A” mark on it. I. Stop the engine. 2. Remove the engine cover. 107 10. MAINTENANCE Propeller PIN THRUST PdPELLER If the propeller is damagedby striking Replacement a rock, or other obstacle, replace the 1. Remove the cotter pin then remove the 18,5 mm castle nut, 19 mm plain washer,propeller and thrust washer. 2. Install the new propeller in the reverse sequenceto removal. Be sure to replace the cotter pin with new one. propeller as follows. l l NUT Before replacing the propeller, remove the engine switch key to prevent accidental engine starting. The propeller is thin and sharp. To protect your hands, wear the heavy gloves during replacement. 108 NOTE: l l Install the thrust washer with the grooved side toward the gear case. Use a genuine Honda cotter pin and bend the pin ends as shown. 10. MAINTENANCE Submerged Motor A submergedmotor must be serviced immediately after it is recov‘eredfrom the water in order to minimize corrosion. Immediately take the outboard motor to the closestauthorized Honda Marine dealer or if you are far from a dealership.proceedas follows: 5. Put a teaspoonof engine oil into eachspark plug hole to lubricate the inside of the cylinders. Then rotate the engine several times, using the emergencystarter rope. Reinstall the spark plugs. 6. Attempt to start the engine (be sure the water level is at least 2 inches abovethe antiventilation plate). Running the outboard motor without sufficient cooling water will damage the water pump and overheat the engine. l I. Removethe engine cover, and rinse the motor with fresh water to remove salt water. sand, mud, etc. 2. Drain the vapor separator. 3. Changethe engine oil (refer to page93). l If the engine fails to start, remove the spark plugs, clean and dry the electrodes,then reinstall the spark plugs and attempt to start the engine again. If the engine starts,and no mechanical damageis evident, continue to run the engine for a I /2 hour or longer. 4. Remove the spark plugs. 109 10. MAINTENANCE l If there was water in the engine crankcase, or the drained used engine oil showed signs of water contamination, then a second engine oil change should be performed after running the engine for a l/2 hour. 7. Take the outboard motor 10your closest authorized Honda Marine dealer for inspection and service as soon as possible. 110 11. STORAGE For longer service life of the outboard motor, have your outboard motor serviced by an authorized Honda Marine dealer before storage. VAPOR SEPARATOR 4. Loosen the vapor separatordrain screw and drain the vapor separator. DRAIN BOLT If you are unable to take the motor to your dealer, proceed as follows: 6. Install the drain hose to the silencer case. Draining the Vapor Separator Be careful not to spill gasoline. Spilled gasoline or gasoline vapor may ignite. If any gasoline is spilled, make sure the area is dry before storing or transporting the motor. Do not smoke or allow flames or sparks where gasoline is drained or stored. m Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. DRAIN H-OSE I. Remove the drain hose from the silencer case. Stop engine and keep heat, sparks, and flame away. 2. Connect the drain hose to the drain joint of the vapor separatorand set the other end of the hose toward the outside of the engine undercase. l Handle fuel only outdoors. 3. Tilt up the outboard motor. l Wipe up spills immediately. l 5. After draining thoroughly, tighten the drain screw securely. 111 11. STORAGE Fuel Tank (optional equipment) Outboard Motor Position --z---T A--.($!gi& =====\ VENT KNOB Vertical storage 1. Remove the engine cover. FUEL CAP 1. CloSethe fuel cap vent knob. 2. Disconnect the fuel coupling from the outboard motor (refer to page 48). 112 Store the motor vertically, as shown above. Store the outboard motor in a well-ventilated area free from direct sunlight and humidity. 11. STORAGE Horizontal storage Before removing the motor from the boat, drain the vapor separatorand engine oil. Follow the vapor separator drain procedure on page 11I. 2. Hook the hoist hook to the lifting eye, and lift the mote; from the boat. STAND 3. Place the motor on an outboard motor stand and secure with bolts and nuts. 4. Remove the lifting eye and install the timing belt cover and engine cover. PdOTECTOR Always rest the motor on protectors, and be sure to protect it from impact and damage. 113 12. TRQUBLESHOOTING WARNING SYSTEM COMES ON POSSIBLE CAUSE SYMPTOM Overheat indicator system activates: l Overheat indicator light comes on. l Overheat indicator buzzer sounds. l Engine speed decreases and stops at last. l Engine speed cannot be increased by opening the throttle. Oil pressure indicator system activates: l Oil pressure indicator light does not come on. l Oil pressure indicator buzzer sounds. l Engine speed decreases. l Engine speed cannot be increased by opening the throttle. PGM-Fl indicator l l PGM-FI PGM-Fl system activates: indicator light comes on. indicator buzzer sounds intermittently. KG indicator system activates: l ACG indicator light comes on. l ACG indicator buzzer sounds intermittently. 114 Cooling water intake port clogged. Spark plug has improper heat range. REMEDY Clean the cooling water intake port. Replace the spark plug (see page 96). . Faulty water pump l Thermostat clogged l Faulty thermostat l Cooling water passage clogged l Exhaust gas invades cooling system. Consult with an authorized outboard motor dealer. Shortage of engine oil. Add engine oil to the specified (see page 38). Improper engine oil is used. Change the engine oil (see page 93). PGM-Fl Consult with an authorized outboard motor dealer. indicator system is faulty. Battery voltage is too high or low. Check the battery. Faulty ACG Consult with an authorized outboard motor dealer. Honda level Honda Honda 13. SPECIFICATIONS MODEL BFI l5A Description Code Type BZBG BZBD BZBG Ignition LA LCA XA XCA Lubrication Overall length 825 mm (32.5 in) Overall width 550 mm (2 I .7 in) Overall height L Starter system BZBD I.650 mm (65.0 in) Electric starter system Specified system oil Full transistor Trochoid Engine: API SAE Gear case: API SAE D.C. output 12V-40A system Water cooling with thermostat Exhaust system Spark plugs Water exhaust KJ22CR-L8 (DENSO) ZFR7F (NGK) Fuel pump Spark plug gap Fuel 0.7 - 0.8 mm (0.028 - 0.03 I in) Gear change 1 standard SC. SH IOW-30140 standard CL-4/S 90 outboard motor gear oil Engine: 5.6 1 (5.9 US qt. 4.9 Imp qt) Gear case: I .O ! (I. I US qt. 0.9 Imp qt) Cooling 4 stroke SOHC in-line 4 cylinder pump pressure lubrication Oil capacity -I ~j battery Diaphragm Automotive type gasoline (86 pump octane) Forward-Neutral-Reverse (dog type) Steering angle 30” right and left Transom angle 5 stages (8’. 12’. 16”. 20’. 24”) 115 13. SPECIFICATIONS Starter system Ignilion system Lubrication Specified Overall width Overall height Transom height Rated power Full throttle range Displacement 116 UL 1,775 mm (69.9 in) L 537 mm (21.1 in) UL 664 mm (26. I in) 228 kg (503 lb) 230 kg (507 lb) 95.6 kW (130 PS)/5,500 rpm Engine type Swk 1,650 mm (65.0 in) 225 kg (496 lb) Dry weight plug gap system oil 550 mm (21.7 in) L Electric Oil capacity Full transistor Trochoid system rpm 5.000 - 6,000 ‘pm 4 stroke SOHC in-line 4 cylinder 2,254 cc (I 37.5 cu-in) 0.7 - 0.8 mm (0.028 - 0.03 I in) Spark plugs l2V-40A Water cooling Gear change with thermostat Water exhaust KJ22CR-L8 (DENSO) ZFR7F (NGK) Fuel pump Fuel standard SG. SH IOW-30140 standard GL-4/5 90 outboard motor gear oil Engine: 5.6 C (5.9 US qt. 4.9 Imp qt) Gear case: I .O e (I. I US qt. 0.9 Imp qt) Exhaust system 233 kg (514 lb) battery pump pressure lubrication Engine: API SAE Gear case: API SAE D.C. output Cooling starter Diaphragm Automotive type gasoline (86 pump octane) Forward-Neutral-Reverse (dog type) Steering angle 30” right and left Transom angle 5 stages (8”. 12’. 16’. 20”. 24”) 14. WARRANTY Warranty Service Information Servicing dealership personnel are trained professionals.They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, pleasediscuss it with the dealership’s management.The Service Manager or General Manager can help. Almost all problems are solved in this way. When you write or call, please give us this information: l l l l If you are dissatisfied with the decision made by the dealership’s management, contact the Honda Marine Customer Relations Office. You can write: SERVICE l l Model and serial numbers (seepage 4) Name of the dealer who sold the outboard motor to you Name and addressof the dealer who services your outboard motor Date of purchase Your name, address,and telephone number A detailed description of the problem American Honda Motor Co., Inc. Marine Division Customer Relations Office 4475 River Green Parkway Duluth, Georgia 30096-2565 Or telephone: (770) 497-6400 117 Current customer service contact information: Your owner's manual was written to cover most of the questions you might ask about your Honda. Any questions not answered in the owner's manual can be answered by your Honda dealer. If your dealer doesn't have an immediate answer, they should be able to get it for you. If you have a difference of opinion with your dealer, please remember that each dealership is independently owned and operated. That's why it's important to work to resolve any differences at the dealership level. If the service personnel are unable to assist you, please discuss your concerns with the dealer management such as the Service Manager or the dealership's owner. If you need to contact American Honda regarding your experiences with your Honda product or with your dealer, please send your comments to the following address: American Honda Motor Co., Inc. Marine Division Customer Relations Office 4900 Marconi Drive Alpharetta, GA 30005-8847 Or telephone: (770) 497-6400 M-F, 8:30 am - 7:00 pm EST When you write or call, please provide the following information: • Your name, address and telephone number (complete with area code) • Model and complete serial number • Date of purchase • Name and location of the selling dealer • Name and location of the servicing dealer (if different) • A detailed description of your concerns 15. INDEX ACG Indicator Light/Buzzer ................................ 18, 23, 29 Anode Metal ..................................................................... ii; PRE-OPERATION CHECK ....................................... MOTOR PROTECTION SYSTEM ............................ 76 I00 Battery (not included)..................................................... Break-in Procedure...........................................................60 CLEANING AND FLUSHING ....................................... 84 COMPONENT IDENTIFICATION .............................. IO Control Lever Friction Adjustment ................................ 45 CONTROLS & INSTRUMENTS (SIDE-MOUNT TYPE) .............................................. I4 (PANEL-MOUNT TYPE) ..........................................20 (TOP-MOUNT TYPE) ................................................26 Cooling System Indicator .................................................35 Cruising (SIDE-MOUNT TYPE) .............................................. 62 (PANEL-MOUNT TYPE) ...........................a.............. 64 (TOP-MOUNT TYPE) ...I............................................ 66 Emergency Stop Switch Lanyard (SIDE-MOUNT TYPE) .............................................. I6 (PANEL-MOUNT TYPE) .......................................... (TOP-MOUNT TYPE) ................................................ ii Engine Cover Removal/Installation ................................. 39 Engine Fuel Filter ............................................................. 103 Engine,Oil Pressure,Overheat, PGM-Fl and ACG Indicator Systems........................................ 73 Engine Oil Level Check ......................................................... 40 Change................................................................... 93 118 Filter Change................................................................. 96 Fast Idle Lever.. ............................................................. 17 Fuel Cap/Gauge/Vent/Knob(optional fuel tank) ................ 37 Level ............................................................................41 Line Connection ..........................................................48 Optional Fuel Tank ......................................................48 Tank and Filter (optional fuel tank) ............................I05 .................................................... 42 Fuel Recommendations FuseReplacement............................................................. 106 Gear Oil ............................................................................98 Gear Shifting (SIDE-MOUNT TYPE) .............................................. 61 (PANEL-MOUNT TYPE) .......................................... 63 (TOP-MOUNTTYPE) ................................................ 65 Ignition Switch (SIDE-MOUNT TYPE) .............................................. 15 (PANEL-MOUNT TYPE) .......................................... 2 1 (TOP-MOUNT TYPE) ................................................27 IMPORTANT SAFETY INFORMATION.. ........................7 Lubrication .....................................................................IO2 MAINTENANCE EMISSION CONTROL SYSTEM INFORMATION ......................................................87 MAINTENANCE SAFETY.. ...................................... 87 SCHEDULE ................................................................91 THE IMPORTANCE OF MAINTENANCE.. ............ 86 Manual Relief Valve coNTRoLs ........................................................33 15. INDEX ORERATION ......................................................70 MOTOR PROTJXTION SYSTEM ................................. 73 Neutral ReleaseLever (SIDE-MOUNT TYPE) ..............................................I5 (PANEL-MOUNT TYPE) ..........................................2 I Oil PressureIndicator Light/Buzzer (SIDE-MOUNT TYPE) ..............................................18 (PANEL-MOUNT TYPE) ..........................................24 (TOP-MOUNT TYPE) ................................................30 .:........................ 47 Other Checks .......................................... Over-Rev Limiter .............................................................37 Overheat Indicator Light/Buzzer (SIDE-MOUNT TYPE) .............................................. (PANEL-MOUNT TYPE) ..........................................:: (TOP-MOUNT TYPE). ...............................................30 OxygenatedFuels .............................................................43 Power Tilt Switch (Motor Pan) CONTROLS ................................................................32 OPERATION ..............................................................67 Power Trim Tilt Switch (SIDE-MOUNT TYPE) ..............................................19 (PANEL-MOUNT TYPE) ..........................................25 (TOP-MOUNT TYPE) ................................................3 I PRE-OPERATION CHECKS ..........................................39 108 Propeller ........................................................................... Cotter pin .....................................................................44 Remote Control Lever (SIDE-MOUNT TYPE) ..............................................14 (PANEL-MOUNT TYPE) ..........................................20 (TOP-MOUNT TYPE) ................................................26 SAFETY LABEL LOCATIONS ..................................... 9 Shallow Water Operation .................................................77 Spark Pluo b ........................................................................ SPECIFICATIONS .......................................................... 1:: STARTING THE ENGINE (SIDE-MOUNT TYPE) ..............................................50 (PANEL-MOUNT TYPE) ..........................................53 (TOP-MOUNT TYPE). ...............................................56 Stem bracket PRE-OPERATION CHECK ....................................... 47 STOPPINGTHE ENGINE (SIDE-MOUNT TYPE) ..............................................78 (PANEL-MOUNT TYPE) ..........................................79 (TOP-MOUNT TYPE) ................................................80 JI J STORAGE.. ...................................................................... SubmergedMotor ............................................................. IO9 Tachometer.......................................................................32 Tilt Lock Lever CONTROLS ................................................................34 OPERATION ..............................................................7 1 Tilting motor POWERTRIM/TILT .................................................67 Tool Kit ............................................................................ Tool Kit and SpareParts...................................................ii Transom Angle Adjusting Rod......................................... 36 TRANSPORTING ............................................................8 1 Trim Meter Controls .......................................................................32 Operation ..................................................................... 69 Trim Tab 119 15. INDEX Controls .......................................................................34 Adjustment .................................................................. 72 TROUBLESHOOTING ...................................................114 Troubleshooting, Starting Problems................................. 59 WARRANTY SERVICE .................................................117 Water Intakes ....................................................................35 I2 I WIRING DIAGRAM ....................................................... 120 . I, 16. WIRING DIAGRAM PANEL/TOP-MOUNT l. I I I i L[UI1 iR SW , ! i- 1 ( ! I 1 I I
advertisement