eDCM 330 Intelligent two door PoE+ Controller Features that make a difference: • Intelligent two door controller supporting 3rd party read heads • Support for two doors • Onboard 10/100Mbps PoE+ Ethernet connectivity to power door equipment via a single CAT5e/6 cable - no local mains required • Communicates directly with the central AC2000 access control system • Database supports 200,000 cardholder records for off-line card validation • Reader communications via standard Wiegand interfaces • Eight supervised inputs (four available per door • Four outputs (2 per door) • Self resetting fuses – saves maintenance time • Onboard LED provides visual status information • Dedicated tamper input • A supervised input can be mapped to a physical output • Suitable for use with AC2000 System family The eDCM 330 (Door Control Module) is a low cost, two-door controller designed to interface third-party read heads with the CEM range of access control systems. The eDCM 330 also combines Power over Ethernet Plus (PoE+) connectivity, which powers door furniture and two heavy duty maglocks via a single CAT 5e/6 network cable.* Featuring PoE+ connectivity, the eDCM 330 has the benefit of eliminating the need for an external local mains power supply at the door. This is particularly beneficial where local power is not readily available or where cabling must be kept to a minimum. Using just a single Cat 5e/6 cable to power the door(s), the eDCM 330 unit can offer significant cost savings. Using a powerful 32bit processor, the eDCM 330 has a large internal database that can store up to 200,000 cardholder records. This gives full off line card validation and decision making capability at the point of entry, when host communication is not available. Up to 8,000 off line transactions can be recorded per door. The eDCM 330 supports most third-party access control read heads conforming to the physical Wiegand (data/data) interfaces, covering a range of technologies from RF Proximity to Biometric devices. The eDCM 330 supports two door configurations. It can either be configured for one read head on each separate door, with optional Exit push buttons, or can be configured to support two reader heads (an Entry/Exit configuration) for bi-directional control on a single door. www.cemsys.com Integral battery backup management is featured with connections to trickle charge a backup battery (12v 7Ah). Also fitted are PoE Fail and Battery Low input sensors. The unit auto restarts when power supply is restored. Control and power up to two doors via Power over Ethernet Plus Technology The eDCM 330 works in conjunction with a PoE+ Midspan power injector between the network and the door and sufficiently powers door read head and two heavy duty maglocks via a single CAT 5e/6 network cable.* This eradicates the need for an extra external power supply above the door. Onboard card reading technologies The eDCM 330 supports a wide range of head technologies using the two available on-board Wiegand connections. Supported card technologies include Wiegand 26bit, CEM 37bit, Mifare, Corporate 1000 and many more. Offline card verification The card database is initially downloaded to the reader’s memory from the host computer with subsequent changes to card data automatically sent as updates. This ensures that the reader has up-to-date card information when operating in offline mode. Operating in off-line mode the reader can hold up to 200,000 cards and 8,000 transactions for each door. Host Communications The eDCM 330 has an on-board 10/100 Mbps Ethernet allowing it to communicate directly with the AC2000 host central system Interlock Mode Airlock mode will create an interlock between both doors when the unit is in two door mode. Full bi-directional interlock is only supported in single door mode. Specifications Physical Size . . . . . . . . . . . . . . . . . . . . Weight . . . . . . . . . . . . . . . . . . Housing . . . . . . . . . . . . . . . . . Colour . . . . . . . . . . . . . . . . . . 460 x 250 x 90mm (18˝ x 10˝ x 3.5˝) 3.75 kg Steel enclosure (colour beige) Grey Power Power requirement . . . . . . . . . PoE Output voltage . . . . . . . . Current Consumption . . . . . . . Backup Battery . . . . . . . . . . . VPoE+ 802.3at compliant Phihong midspan 33.6W per port 12Vdc @ 1.9A* for DCM board 200mA for DCM board (excluding locks and heads) Integral charging circuit provided with enclosure and space battery (Battery not supplied) Functionality Temperature . . . . . . . . . . . . . . -10º to 55°C (14° to 133°F) LED Indicators . . . . . . . . . . . . Power, Link to host, Comms Tx/Rx, Fault / Tamper, Lock and Relay Status Functionality Configuration Operational parameters are downloaded from host computer eDCM 330 Inputs . . . . . . . . . . Door Position* Lock Status* Exit Push Button* Interlock* Power Fail Tamper Battery Low (reported internally) Dedicated Power Fail Input The PoE+ injector or mid span device supplies all the power for the devices and locks required by two doors. Ordering Information Product Code Description DCM/330/101 eDCM 330 components mounted in enclosure. CEQ/576/001 Phihong PoE MidSpan device – 1 Port (PoE36u-1AT) CEQ/576/004 Phihong PoE MidSpan device – 4 Port (PoE125u-4AT) CEQ/576/008 Phihong PoE MidSpan device - 8 Port (POE576U-8AT) CEQ/576/016 Phihong PoE MidSpan device 16 Port (POE576U-16AT) * = 4 state tamper protected inputs These physical inputs can be used, if spare, as general inputs for alarm monitoring eDCM 330 Outputs . . . . . . . . Two Relays rated at [email protected] Two 12V open collector outputs limited to 1.5A (Door Lock and External Sounder) Reader capacity . . . . . . . . . . . Configuration . . . . . . . . . . . . . Database Memory . . . . . . . . . Cardholders . . . . . . . . . . . . . . Transactions . . . . . . . . . . . . . . PCB Battery . . . . . . . . . . . . . . 2 Weigand interfaces (data/data) Operational parameters are downloaded from host computer 1gB SD Card Storage up to 200,000 cardholders at the door Up to 8,000 transactions in offline operation 3.0V rechargeable Lithium; Used for PCB real-time clock only * Up to 1.9 Amps at 12V available at the door to power the DCM board including all attached devices, using a CEM recommended Phihong midspan and up to 50m of CAT5e/6 cable at room temperature. Requirements Compatible with the AC2000 access control family: • AC2000 • AC2000 Airport • AC2000 Lite • RTC Ethernet Reader Controller Related Products AC2000 AC2000 Airport AC2000 Lite www.cemsys.com © 2015 Tyco Security Products. All Rights Reserved. CEM/B/319 Rev D Tyco and the product names listed above are marks and/or registered marks. Unauthorized use is strictly prohibited. Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021