GE D1000 Series Security IFS RS-232/422 Point-to-Point

GE D1000 Series Security IFS RS-232/422 Point-to-Point
GE
Security
D1000 Series
IFS RS-232/422 Point-to-Point
Data Transceivers
Overview
Standard Features
The IFS D1000 series data transceivers provide point-topoint transmission of simplex or duplex EIA RS232/RS-422
data signals over one or two optical fibers. The transceivers
are transparent to data encoding allowing for broad-range
compatibility. The transceivers are also compatible with the
IFS D2100 series drop and repeat data transceivers when
used as line terminating devices. Models within this series
are available for use with multimode or single mode optical fiber. Plug-and-play design ensures ease of installation
requiring no electrical or optical adjustments. Each
transceiver incorporates power and transmit/receive data
status indicating LED’s for monitoring proper system
operation. The modules are available in either stand-alone
or rack mount versions.
• Meets EIA RS-232/422 Specifications (Simplex or Duplex)
Application Examples
• Access Control Systems
• Building Automation and Environmental Control Systems
• Computer/Data Equipment
• Fire & Alarm Systems
• Traffic Signal Control Equipment
• Point-to-Point Topology
• Transparent to Data Encoding / Compatible with
Major Data Protocols
• Data Rates up to 1.5 Mbps
• No In-field Electrical or Optical Adjustments Required
• Power, Transmit and Receive Data Status LED Indicators
• NTCIP Compatible
• Tested and Certified by an Independent Testing
Laboratory for Full Compliance with the Environmental
Requirements (Ambient Operating Temperature,
Mechanical Shock, Vibration, Humidity with Condensation,
High-Line/Low-Line Voltage Conditions and Transient
Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans Specification for Traffic Signal Control Equipment.
• Integrated WDM for Greater Product Reliability
• Automatic Resettable Solid-State Current Limiters
• Hot-Swappable Rack Modules
• Distances up to 37 Miles (60 km)
• Comprehensive Lifetime Warranty
RS-232/422
Point-to-Point
Data Transceivers
Transmission of simplex or duplex
EIA RS-232/RS-422 data signals
over one or two optical fibers.
GE
Security
Specifications
Data
Data Interface: Data Rate:
Operating Mode:
Bit Error Rate:
North America
T 888-GE-SECURITY
888-437-3287
F 503-691-7566
E [email protected]
RS-232 (data lines only), or RS-422 (see note)
DC - 1.5 Mbps (NRZ)
Asynchronous Simplex or Full-Duplex
<1 in 10˚
D1010: 850 nm, MM D1010WDMA: 850/1310 nm, MM
D1010WDMB: 1310/850 nm, MM D1020: 1310 nm, MM
D1030: 1310 nm, SM D1030WDMA: 1310 nm, SM
D1030WDMB: 1550 nm, SM
Wavelength
Number Of Fibers
Asia
T 852-2907-8108
F 852-2142-5063
Australia and New Zealand
T 613-9239-1200
F 613-9239-1299
D1010: 2
D1030: 2
Connectors
Optical: Data and Power:
Electrical & Mechanical
Power:
Surface Mount:
Rack:
Number of Rack Slots:
Current Protection:
Circuit Board:
Size (in./cm.) (LxWxH)
Surface Mount: Rack Mount: Shipping Weight:
Europe
T 44-113-238-1668
F 44-113-253-8121
Latin America
T 305-593-4301
F 305-593-4300
gesecurity.com/ifs
Specifications subject to
change without notice
Agency compliance
D1010WDMB: 1 D1020: 2
D1030WDMB: 1
ST
Terminal Block with Screw Clamps
12 VDC @ 150 mA
From Rack
1
Automatic Resettable Solid-State Current Limiters
Meets IPC Standard
4.2 x 4.0 x 1.0 in., 10.7 x 8.9 x 2.5 cm
7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm
< 2 lbs./0.9 kg
Environmental
MTBF: Operating Temp: Storage Temp: Relative Humidity: © 2008 General Electric Company
All Rights Reserved
D1010WDMA: 1
D1030WDMA: 1
> 100,000 hours
-40° C to +74° C
-40° C to +85° C
0% to 95% (non-condensing)†
†May be extended to condensation conditions by adding suffix ‘–C’ to
model number for conformal coating.
NOTE: The D1010 Series is compatible with some RS-485 (4-wire) systems, consult factory.
Made in the USA
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
Ordering Information
Multimode
62.5/125µm**
Single Mode
9/125µm
Part Number
Description
Fibers Required Opt. Pwr. Budget Max. Distance*
D1010
D1010WDMA✧
D1010WDMB
D1020
RS-232/RS-422 Data Transceiver (850 nm)
RS-232/RS-422 Data Transceiver (850/1310 nm)
RS-232/RS-422 Data Transceiver (1310/850 nm)
RS-232/RS-422 Data Transceiver (1310 nm)
2
1
1
2
14 dB
14 dB
14 dB
13 dB
2.5 miles (4 km)
2.5 miles (4 km)
2.5 miles (4 km)
8 miles (13 km)
D1030
D1030WDMA✧
D1030WDMB
RS-232/RS-422 Data Transceiver (1310 nm)
RS-232/RS-422 Data Transceiver (1310 nm)
RS-232/RS-422 Data Transceiver (1550 nm)
2
1
1
20 dB
37 miles (60 km)
Accessories♦
PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)
Options
Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget. ♦ All accessories are third party manufactured. ✧ WDMA must mate with a WDMB.
System Design
D1010
ifs
up to 2.5 miles
(4 km)
Fiber
Systems
Incorporated
203.426.1180
RS-232
or
RS-422*
Host
D1010
ifs
International
International
*Note: Unit can be used for transmission of
RS-232 or RS-422, but not simultaneously
Fiber
Systems
Incorporated
203.426.1180
RS-232
or
RS-422*
2 Fibers
62.5/125µm MM
Remote
1. Point to point (dual fiber)
D1010WDMA
ifs
203.426.1180
RS-232
or
RS-422*
Host
up to 2.5 miles
(4 km)
International
Fiber
Systems
Incorporated
1 Fiber
62.5/125µm MM
D1010WDMB
ifs
International
Fiber
Systems
Incorporated
203.426.1180
2. Point to point (single fiber)
RS-232
or
RS-422*
Remote
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement