Hotpoint NVLR333EVAA Clothes Dryer User Manual

Hotpoint NVLR333EVAA Clothes Dryer User Manual
NVLR333GVWW—Hotpoint 5.4 Cu. Ft. Large Capacity Gas Dryer
Dryer Dimensions (in inches)
23-1/2
Exhaust Options:
3-way via rear, left and bottom. Dryer is shipped exhausted to the rear.
Alternate exhausting knockouts are supplied.
25-3/4
25-1/2
4-3/4
27
36
42
2-1/2
Side View
Specification Revised 8/99
Circuit Requirements:
An individual properly-grounded branch circuit, with a three-prong groundingtype receptacle, protected by a 15- or 20-amp circuit breaker or a time-delay
fuse is required.
Gas Dryer Electric Rating:
120V, 60Hz, 15 Amp
11-3/4
2
Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas.
LP gas supply requires a conversion kit. Check installation instructions for
correct kit and have a qualified gas technician install a conversion kit. See
dryer ducting information for proper installation.
5-1/2
Installation Information: For complete information, see installation
instructions packed with product for current dimensional data.
Rear View
R
Listed by
Underwriters
Laboratories
NVLR333GVWW—Hotpoint 5.4 Cu. Ft. Large Capacity Gas Dryer
Dryer Exhausting Information—Use Metal Duct Only
Best Performance
A
A
4
B
Domestic
Dryer Models
2-1/2
Super & Extra-Large
Capacity Models
All Electric Dryers
Super & Extra-Large
Capacity Models
All Gas Dryers
Large Capacity
Electric and
Gas Dryers
Number
of
90°
Turns
0
1
2
3
4
0
1
2
3
0
1
2
3
4
Maximum Length of 4"
Dia. Rigid Metal Duct
Exhaust Hood Type
Maximum Length of 4"
Dia. Flexible Metal Duct
Exhaust Hood Type
Cat. No.
WX8X59
(Preferred)
A
4" Opening
90 ft.
60 ft.
45 ft.
35 ft.
25 ft.
45 ft.
35 ft.
25 ft.
15 ft.
60 ft.
52 ft.
44 ft.
32 ft.
28 ft.
Cat. No.
WX8X59
(Preferred)
A
4" Opening
55 ft.
40 ft.
30 ft.
20 ft.
15 ft.
30 ft.
20 ft.
10 ft.
—
30 ft.
22 ft.
14 ft.
—
—
Specification Revised 8/99
B
2-1/2"
Opening
60 ft.
45 ft.
35 ft.
25 ft.
15 ft.
30 ft.
20 ft.
10 ft.
—
48 ft.
40 ft.
32 ft.
24 ft.
16 ft.
B
2-1/2"
Opening
45 ft.
30 ft.
20 ft.
15 ft.
10 ft.
15 ft.
10 ft.
—
—
18 ft.
14 ft.
10 ft.
— ft.
— ft.
For complete information, see installation instructions packed with your dryer.
Important Note:
GE Kit Number WE14X70 needed when converting rear exhaust to bottom or side. (On large capacity models.)
Ducting Materials:
For best performance, this dryer should be vented with 4” diameter all rigid metal exhaust duct. If “all rigid metal” duct cannot be
used, then “flexible all metal” venting can be used, but it will reduce the maximum recommended duct length.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. The maximum length
for flexible ducts are less than for rigid duct.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45°
should be treated as a 90° elbow.
Exhausting the dryer to the outside is strongly recommended to prevent large amounts of moisture and lint from being
blown into the room. Gas dryers or any dryer located in a closet must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an
attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a
common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be
located at least 12” above the ground or any other obstruction with the opening pointed Down.
Other terminations, such as louvered wall boxes, are acceptable provided they are equivalent to a 4” opening dampered wall cap.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0” either side
3” front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed.
If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
• The closet should be vented to the outdoors to prevent gas pocketing in case of a gas leak in the supply line.
• No other fuel-burning appliance shall be installed in the same closet with the dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.
Minimum Clearances other than Alcove or Closet Installation:
•Minimum clearances to combustible surfaces
Listed by
0” both sides
Underwriters
3” rear
R
Laboratories
NVLR333GVWW—Hotpoint 5.4 Cu. Ft. Large Capacity Gas Dryer
Features and Benefits
• Large Capacity (5.4 Cubic Feet)
• Automatic Dry Control
• 3 Cycle Selections: Cottons, Permanent Press, 70 Minute Timed Dry (No-Heat)
• 3 Heat Selections
• Up-Front Lint Filter
• Porcelain Drum Interior
• Front Serviceable
• Model NVLR333EVWW–White on White (Electric)
• Model NVLR333EVAA–Almond on Almond (Electric)
• Model NVLR333GVWW–White on White (Gas)
• Model NVLR333GVAA–Almond on Almond (Gas)
Specification Revised 8/99
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement