Husqvarna 67522ES Lawn Mower User Manual

Husqvarna 67522ES Lawn Mower User Manual

67522ES

Owner’s Manual

532 40 05-10 Rev. 1 03.07.06 BY Printed in U.S.A.

SAFETY RULES

Safe Operation Practices for Walk-Behind Mowers

IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE

TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

Look for this symbol to point out im-

por tant safety precautions. It means

SAFE TY IS IN VOLVED.

CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent ac ci den tal adjusting or making re pairs.

WARNING: Engine exhaust, some of its con stit u ents, and certain vehicle com po nents contain or emit chem i cals known to the State of Cal i for nia to cause can cer and birth defects or oth er re pro duc tive harm.

WARNING: Battery posts, terminals and related ac ces so ries contain lead and lead compounds, chemicals known to the State

• Stop the blade(s) when crossing gravel drives, walks, or roads.

• Stop the engine (motor) whenever you leave the equip-

ment, before cleaning the mower or unclogging the chute.

• Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catch er.

• Mow only in daylight or good artifi cial light.

• Do not operate the machine while under the infl uence of alcohol or drugs.

• Never operate machine in wet grass. Always be sure of your footing: keep a fi rm hold on the handle and walk; never run.

• Disengage the self-propelled mechanism or drive clutch on mowers so equipped before starting the engine (motor).

• If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

• Always wear safety goggles or safety glasses with side shields when operating mower.

defects or oth er re pro duc tive harm. Wash hands after handling.

CAUTION: Muffl er and other engine parts become extremely hot during operation and remain hot after engine has stopped.

To avoid severe burns on contact, stay away from these areas.

II. SLOPE OPERATION

Slopes are a major factor related to slip and fall accidents which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it.

DO:

• Mow across the face of slopes: never up and down. Exercise extreme caution when changing direction on slopes.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Tall grass can hide obstacles.

DO NOT:

• Do not trim near drop-offs, ditches or embankments.

The operator could lose footing or balance.

• Do not trim excessively steep slopes.

• Do not mow on wet grass. Reduced footing could cause slipping.

I. GENERAL OPERATION

• Read, understand, and follow all instructions on the machine and in the manual(s) before starting. Be thor-

ough ly familiar with the controls and the proper use of the machine before starting.

• Do not put hands or feet near or under rotating parts.

Keep clear of the discharge opening at all times.

• Only allow responsible individuals, who are familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire, bones, sticks, etc., which could be picked up and thrown by the blade.

• Be sure the area is clear of other people before mow-

ing. Stop machine if anyone enters the area.

• Do not operate the mower when barefoot or wearing open sandals. Always wear substantial foot wear.

• Do not pull mower backwards unless absolutely nec-

es sary. Always look down and behind before and while moving backwards.

• Never direct discharged material toward anyone.

Avoid discharging material against a wall or obstruction. Material may richochet back toward the operator.

Stop the blade when crossing gravel surfaces.

• Do not operate the mower without proper guards, plates, grass catcher or other safety protective devices in place.

• See manufacturer’s instructions for proper operation and installation of accessories. Only use accessories approved by the manufacturer.

2

III. CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

• Keep children out of the trimming area and under the watchful care of another re spon si ble adult.

• Be alert and turn machine off if children enter the area.

• Before and while walking backwards, look behind and down for small children.

• Never allow children to operate the machine.

• Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SAFE HANDLING OF GASOLINE

Use extreme care in handling gasoline. Gasoline is extremely fl ammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• Use only an approved container.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

• Never refuel the machine indoors.

• Never store the machine or fuel container where there is an open fl ame, spark or pilot light such as a water heater or on other appliances.

• Never fi ll containers inside a vehicle, on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before fi lling.

• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete.

Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overfi ll fuel tank. Replace gas cap and tighten securely.

V. GENERAL SERVICE

• Never run a machine inside a closed area.

• Never make adjustments or repairs with the engine

(motor) running. Disconnect spark plug wire, and keep wire away from plug to prevent accidental starting.

• Keep nuts and bolts, especially blade attachement bolts, tight and keep equipment in good condition.

• Never tamper with safety devices. Check their proper operation regularly.

• Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

• Never attempt to make wheel height adjustments while the engine (motor) is running.

• Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check com po nents and replace with manufacturer’s rec om mend ed parts, when necessary.

• Mower blade is sharp and can cut. Wrap the blade or wear gloves, and use extra caution when servicing it.

• Do not change the engine governor setting or overspeed the engine.

• Maintain or replace safety and instruction labels, as necessary.

WARNING: This lawn mower is equipped with an internal com bus tion engine and should not be used on or near any un im proved forest-covered, brush-covered or grass-cov ered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. A spark arrester for the muffl er is available through your nearest authorized service centre.

CONGRATULATIONS on your purchase of a new lawn mower. It has been designed, engineered and man u fac tured to give you the best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center/department. We have competent, well-trained tech ni cians and the proper tools to service or repair this lawn mower.

Please read and retain this manual. The instructions will enable you to assemble and maintain your lawn mower properly. Always observe the “SAFETY RULES”.

SERIAL

NUMBER: _________________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND

ON A DECAL ATTACHED TO THE REAR OF THE LAWN

MOWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity 1.6 Quarts and Type: (Unleaded Regular Only)

Oil Type (API SG–SL): SAE 30 (above 32°F);

SAE 5W-30 (below 32°F)

Oil Capacity: 20 Ounces

Spark Plug (Gap: .030"): Champion J19LM or RJ19LM

Blade Bolt Torque: 35-40 ft. lbs. (47-54 N-m)

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for and using your lawn mower.

• Follow the instructions under “Maintenance” and “Stor-

age” sec tions of this own er’s manual.

TABLE OF CONTENTS

SAFETY RULES ......................................................... 2-3

PRODUCT SPECIFICATIONS....................................... 3

CUSTOMER RESPONSIBILITIES................................. 3

ASSEMBLY.................................................................... 4

OPERATION ............................................................... 5-8

MAINTENANCE SCHEDULE ........................................ 9

3

MAINTENANCE ........................................................ 9-11

SERVICE AND AD JUST MENTS ............................ 12-13

STORAGE............................................................... 13-14

TROU BLE SHOOT ING ................................................. 15

REPAIR PARTS ...................................................... 16-19

WARRANTY................................................................. 20

ASSEMBLY

Read these instructions and this man u al in its entirety before you attempt to assemble or operate your new lawn mow er.

IMPORTANT: THIS LAWN MOWER IS SHIPPED WITH OUT OIL OR GASOLINE IN THE ENGINE.

Your new lawn mower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts bag. To ensure safe and proper operation of your lawn mow er, all parts and hard ware you assemble must be tightened se cure ly. Use the correct tools as nec es sary to ensure proper tightness.

TO RE MOVE LAWN MOW ER FROM CAR TON

1. Remove loose parts included with mower.

2. Cut down two end corners of car ton and lay end panel down fl at.

3. Remove all packing materials ex cept padding be tween upper and lower handle and padding holding operator presence control bar to up per handle.

4. Roll lawn mower out of carton and check carton thorougly for ad di tion al loose parts.

FRAME

HANDLE

HOW TO SET UP YOUR LAWN MOW ER

TO UNFOLD HANDLE (See Fig. 1)

IMPORTANT: UNFOLD HANDLE CAREFULLY SO AS

NOT TO PINCH OR DAMAGE CON TROL CABLES.

1. Raise handles until lower handle section locks into place in mowing position.

2. Remove protective padding, raise upper handle sec tion into place on lower handle and tighten both handle knobs.

3. Remove handle padding holding operator pres ence control bar to upper handle.

Your handles may be adjusted for your mowing comfort.

Refer to “ADJUST HANDLE” in the Service and Ad just ments sec tion of this man u al.

OPERATOR

PRESENCE

CONTROL

BAR

MOWING

PO SI TION

LIFT

UP

LIFT

UP

UPPER

HANDLE

VINYL

BINDINGS

FRAME

OPENING

FIG. 2

TO INSTALL ATTACHMENTS

Your lawn mower was shipped ready to be used as a mulcher. To convert mower to bagging or discharging, see “TO CON VERT MOWER” in the Operation section of this man u al.

TO PREPARE BATTERY (See Fig. 3)

NOTE: Your battery must be charged before you can start your lawn mower.

1. Con nect battery charger con nec tor (male) to harness con nec tor (fe male).

2. Plug battery charger into 110 volt A.C. outlet.

3. Leave battery charger connected for 24 hours before starting your engine for the fi rst time.

4. After charging, disconnect harness connector (female) from bat tery charger connector (male).

Connect your battery charger to charge battery after each use.

IMPORTANT: THE ENGINE WILL NOT RECHARGE YOUR

BATTERY. AT THE END OF THE MOWING SEASON THE

BATTERY SHOULD BE CHARGED FOR 48 HOURS TO

PROTECT THE BATTERY DURING WINTER STORAGE.

HANDLE

KNOB

CAUTION: Always disconnect the en-

gine connector (male) from the battery connector (female) to prevent ac ci den tal start ing when transporting or stor ing your lawn mower after the season.

LOWER

HANDLE

FIG. 1

TO ASSEMBLE GRASS CATCHER (See Fig. 2)

1. Put grass catcher frame into grass bag with rigid part of bag on the bottom. Make sure the frame handle is outside of the bag top.

2. Slip vinyl bindings over frame.

NOTE: If vinyl bindings are too stiff, hold them in warm water for a few minutes. If bag gets wet, let it dry before using.

4

BATTERY

BOX

BATTERY

CHARGER

ENGINE

CONNECTOR

(MALE)

FIG. 3

HARNESS

CONNECTOR

(FEMALE)

CHARGER

CONNECTOR (MALE)

OPERATION

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER.

Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments.

Save this manual for future reference.

These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand their meaning.

OPERATOR PRESENCE CON TROL BAR

KEY START

SWITCH

AUXILIARY

STARTER

HANDLE

DRIVE CONTROL LEVER

HANDLE KNOB

EN GINE OIL CAP WITH DIPSTICK

GRASS

CATCHER

GAS O LINE

FILL ER CAP

MUFFLER

DRIVE COVER

WHEEL

ADJUSTER

(ON EACH

WHEEL)

AIR FILTER

MULCHER DOOR

IMPORTANT: This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine.

PRIMER

SPARK PLUG

HOUSING

MEETS CPSC SAFETY REQUIREMENTS

Our rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S. Consumer Product Safety Commission. The blade turns when the engine is running.

AUXILIARY STARTER HANDLE – used for starting the engine.

PRIMER – pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

MULCHER DOOR – allows conversion to discharge or bagging operation.

5

OPERATOR PRESENCE CONTROL BAR – must be held down to the handle to start the engine. Release to stop the engine.

DRIVE CONTROL LEVER used to engage power-pro-

pelled forward mo tion of lawn mower.

KEY START SWITCH – used for start ing the engine.

OPERATION

The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask over spectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory for optimum performance. Speed is not adjustable.

ENGINE ZONE CONTROL

CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk of blade contact injury. Do not un der any cir cum stanc es attempt to defeat the function of the operator control. The blade turns when the engine is running.

• Your lawn mower is equipped with an operator presence control bar which requires the operator to be positioned behind the mower handle to start and operate the mower.

DRIVE CONTROL (See Fig. 4)

• Self-propelling is controlled by hold ing the operator presence control bar down to the handle and pulling the drive control lever rearward to the handle. The farther toward the handle the lever is pulled, the faster the unit will travel.

• Forward motion will stop when either the operator presence control bar or drive control lever are released. To stop forward motion without stop ping engine, re lease the drive control lever only. Hold op er a tor presence control bar down against handle to con tin ue mowing without self-propelling.

NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels.

• To keep drive control engaged when turning corners, push down on the handle to lift the front wheels off the ground while turning lawn mower.

OPERATOR PRESENCE CONTROL BAR

1. Turn unit off and disconnect spark plug wire from plug.

2. Rotate turnbuckle on drive control to increase drive speed.

3. Operate mower to test drive speed. Readjust as required.

4. If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn and should be re placed.

TO ADJUST CUTTING HEIGHT (See Fig. 5)

Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit your requirements. Me di um position is best for most lawns.

• To change cutting height, squeeze adjuster lever to ward wheel. Move wheel up or down to suit your re quire ments.

Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs.

LEVER BACKWARD TO LOWER MOWER

PLATE

TAB

LEVER FORWARD TO RAISE MOWER

LEVER

FIG. 5

TO CONVERT MOWER

Your lawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging:

REAR BAGGING (See Fig. 6)

• Open rear door and remove mulcher plug. Store mulcher plug in a safe place.

• You can now install the grass catcher or optional clipping defl ector.

• To convert to mulching or discharging operation, install mulcher plug into rear discharge opening of mower.

ADJUSTMENT

TURNBUCKLE

(ON UNDERSIDE)

TO

ENGAGE

DRIVE

CONTROL

DRIVE

CONTROL

LEVER

DRIVE

CONTROL

DISENGAGED

FIG. 4

DRIVE CONTROL ADJUSTMENT (See Fig. 4)

Over time, the drive control system may become “loose”, resulting in decreased speed. There is a turnbuckle on the un der side of the drive control housing to increase tension on the drive cable. Pro ceed as follows:

6

MULCHER

PLUG

FIG. 6

OPERATION

SIDE DIS CHARG ING (See Fig. 7)

• Mulcher plug must be installed into rear discharge open ing of mower.

• Open mulcher door and install dis charge defl ector under door as shown.

• Mower is now ready for discharging operation.

• To convert to mulching or bagging operation, dis charge defl ector must be removed and mulcher door closed.

CAUTION: Do not run your lawn mower with out mulcher plug or ap proved grass catch er in place. Never at tempt to op-

er ate the lawn mow er with the rear door re moved or propped open.

TO EMPTY GRASS CATCHER (See Fig. 8)

1. Lift up on grass catcher using the frame han dle.

2. Remove grass catcher with clippings from under lawn mower han dle.

3. Empty clippings from bag.

NOTE: Do not drag the bag when emptying; it will cause unnecessary wear.

FRAME

HANDLE

OPEN MULCHER DOOR

DISCHARGE DEFLECTOR

FIG. 8

BEFORE STARTING ENGINE

ADD OIL (See Fig. 9)

Your lawnmower is shipped without oil in the engine. For type and grade of oil to use, see “EN GINE” in the Maintenance section of this manual.

CAUTION: DO NOT overfi ll engine with oil, or it will smoke on startup.

FIG. 7

SIMPLE STEPS TO REMEMBER

WHEN CONVERTING YOUR LAWN MOWER:

FOR MULCHING -

1. Mulcher plug installed.

2. Mulcher door closed.

FOR REAR BAGGING -

1. Mulcher plug removed.

2. Grass catcher installed.

3. Mulcher door closed.

FOR SIDE DISCHARGING -

1. Mulcher plug installed.

2. Discharge defl ector installed.

7

1. Be sure lawnmower is level.

2. Remove oil dipstick from oil fi ll spout.

3. Engine holds 20 ounces of oil. For type and grade of oil to use, see “ENGINE” in the Maintenance section of this manual.

4. Pour oil slowly. Do not overfi ll. Wait one minute to allow oil to settle. Insert and tighten dipstick, then remove it to check oil level.

IMPORTANT:

• Check oil level before each use. Add oil if needed. Fill to full line on dipstick.

• Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirty conditions. See “TO CHANGE EN-

GINE OIL” in the Maintenance section of this manual.

GASOLINE

FILLER

CAP

OPERATION

MOWING TIPS

ENGINE

OIL CAP

CAUTION: Do not use de-thatcher blade attachments on your mower. Such attachments are hazardous, will damage your mower and could void your warranty.

PRIMER

FIG. 9

ADD GASOLINE (See Fig. 9)

• Fill fuel tank to bottom of tank fi ller neck. Do not overfi ll. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quan ti ties that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open fl ame.

Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before stor age of 30 days or longer.

Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage

In struc tions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO STOP ENGINE

• To stop engine, release operator presence con trol bar.

TO START ENGINE

NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal.

1. To start a cold engine, push primer three (3) times before trying to start. Use a fi rm push. This step is not usually necessary when starting an engine which has already run for a few minutes.

2. Hold operator presence control bar down to the han dle and turn the start key.

IMPORTANT: DO NOT CRANK ENGINE MORE THAN FIVE

CONTINOUS SECONDS BETWEEN EACH TIME YOU TRY TO

START. WAIT 5 TO 10 SECONDS BETWEEN EACH ATTEMPT.

• To start engine using the rope start er, follow the steps above. Exchange the use of the starter rope for start key. Pull starter handle quickly. Do not allow starter rope to snap back.

NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause fl ooding and engine will not start. If you do fl ood engine, wait a few minutes before attempting to start and do not repeat priming steps.

8

• Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings. It may also be necessary to reduce ground speed and/or run the lawn mower over the area a second time.

• For extremely heavy cutting, reduce the width of cut by overlapping previously cut path and mow slowly.

• For better grass bagging and most cutting conditions, the engine speed should be set in the fast position.

• Pores in cloth grass catchers can become fi lled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catcher off with water and let dry before using.

• Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air fl ow and extend engine life.

MULCHING MOWING TIPS

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE

“CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL.

• The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades.

• Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action.

The best time to mow your lawn is the early afternoon.

At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight.

• For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. 10). If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly.

MAX 1/3

FIG. 10

• Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the fi rst cut path.

• Change your cutting pattern from week to week. Mow north–south one week, then change to east–west the next week. This helps prevent matting/graining of lawn.

MAINTENANCE

BEFORE

EACH

USE

AFTER

EACH

USE

EVERY

10

HOURS

EVERY

25 HOURS

OR SEASON

EVERY

100

HOURS

BEFORE

STORAGE

*

Check for Loose Fasteners

Clean / Inspect Grass Catcher *

Check Tires

Check Drive Wheels ***

Clean Lawn Mower ****

Clean under Drive Cover ***

Check Drive Belt / Pulleys ***

Check / Sharpen / Replace Blade

Lubrication

Clean and Recharge Battery **

Check Engine Oil level

Change Engine Oil

Clean Air Filter

Inspect Muffler

Replace Spark Plug

Replace Air Filter Paper Cartridge

Empty fuel system or add Stabilizer

(if so equipped)

**

***

****

Electric-Start mowers

Power-Propelled mowers

Use a scraper to clean under deck

1 - Change more often if operating under a heavy load or in high outdoor temperatures.

2 - Service more often if operating in dirty or dusty conditions.

3 - Replace blades more often when mowing in sandy soil.

4 - Charge 48 hours at end of season.

5 - And after each 5 hours of use.

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual.

Some adjustments will need to be made periodically to properly maintain your unit.

At least once a season, check to see if you should make any of the adjustments described in the Service and Ad-

just ments section of this manual.

• At least once a year, replace the spark plug, clean or replace air fi lter element and check blade for wear. A new spark plug and clean/new air fi lter element assure proper air-fuel mixture and help your engine run better and last longer.

• Follow the maintenance schedule in this manual.

LUBRICATION CHART

WHEEL

ADJUSTER

(ON EACH

WHEEL)

ENGINE OIL

MULCHER

DOOR

HINGE PIN

REAR DOOR HINGE

BEFORE EACH USE

1. Check engine oil level.

2. Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”).

IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL

BEARINGS. VISCOUS LU BRI CANTS WILL ATTRACT DUST

AND DIRT THAT WILL SHORT EN THE LIFE OF THE SELF-

LU BRI CAT ING BEARINGS. IF YOU FEEL THEY MUST BE

TYPE LUBRICANT SPAR INGLY.

HANDLE BRACK ET MOUNT ING PINS

9

SPRAY LUBRICANT

SEE “ENGINE” IN MAINTENANCE SECTION

MAINTENANCE

LAWN MOWER

Always observe safety rules when performing main te nance.

TIRES

• Keep tires free of gasoline, oil, or insect control chem-

i cals which can harm rubber.

• Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

3. Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine.

4. Install the blade bolt with the lock washer and hard ened washer into blade adapter and crank shaft.

5. Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clock wise.

• The recommended tightening torque is 35-40 ft. lbs.

IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS

REPLACING, REPLACE ONLY WITH APPROVED BOLT SHOWN

IN THE REPAIR PARTS SECTION OF THIS MANUAL.

DRIVE WHEELS

Check front drive wheels each time be fore you mow to be sure they move freely.

The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1. Remove hubcaps, locknuts and washers.

2. Remove wheels from wheel ad just ers.

3. Remove any trash or grass cuttings from inside the dust cover, pinion and/or drive wheel gear teeth.

4. Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a qualifi ed service center.

BLADE ADAPTER

BLADE

LOCK

WASHER

BLADE

BOLT

HARDENED

WASHER

KEY

TRAILING EDGE

CRANKSHAFT

KEY WAY

CRANKSHAFT

BLADE CARE

For best results, mower blade must be kept sharp. Re place a bent or dam aged blade.

CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE (See Fig. 11)

1. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2. Turn lawn mower on its side. Make sure air fi lter and carburetor are up.

3. Use a wood block between blade and mower hous ing to prevent blade from turning when re mov ing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4. Remove blade bolt by turning counter-clockwise.

5. Remove blade and attaching hardware (bolt, lock wash er and hardened wash er).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if dam aged.

TO REPLACE BLADE (See Fig. 11)

1. Position the blade adapter on the engine crank shaft.

Be sure key in adapter and crankshaft key way are aligned.

2. Position the blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

10

FIG. 11

TO SHARPEN BLADE

NOTE: We do not recommend sharp en ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un bal anced blade will cause eventual damage to lawn mower or engine.

• The blade can be sharp ened with a fi le or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, drive a nail into a beam or wall. Leave about one inch of the straight nail ex posed.

Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GEAR CASE

• To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season.

• The gear case is fi lled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

• If lubricant is required, use only ELF Multis EP00. Do not sub sti tute.

GRASS CATCHER

• The grass catcher may be hosed with water, but must be dry when used.

• Check your grass catcher often for damage or de te ri o ra tion. Through normal use it will wear. If catcher needs replacing, replace only with ap proved replacement catcher shown in the Repair Parts section of this manual. Give the mower model number when ordering.

MAINTENANCE

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classifi cation SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

SAE 30

5W-30

F

C

-20 0 30 32 40

60 80

100

-30 -20 -10 0 10 20 30

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

40

NOTE: Multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, and you should check your engine oil level frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the lawn mower is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each fi ve (5) hours of continuous use. Tighten oil plug securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Fig. 12)

NOTE: Before tipping lawn mower to drain oil, empty fuel tank by running engine until fuel tank is empty.

1. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2. Remove engine oil cap; lay aside on a clean surface.

3. Tip lawn mower on its side as shown and drain oil into a suitable container. Rock lawn mower back and forth to remove any oil trapped inside of engine.

4. Wipe off any spilled oil from mower or side of engine.

TO CLEAN AIR FILTER

1. Loosen screw and tilt cover to re move.

2. Carefully remove cartridge.

3. Clean by gently tapping on a fl at surface. If very dirty, replace car tridge.

CAUTION: Pe tro leum solvents, such as ker o sene, are not to be used to clean car tridge. They may cause de te ri o ra tion of the cartridge. Do not oil car tridge.

Do not use pres sur ized air to clean or dry car tridge.

4. Install cartridge, then replace cover making sure the tabs are aligned with the slots in the back plate. Fasten screw securely.

LIP BACK

PLATE

SLOTS

CARTRIDGE

COVER

COVER

TABS

FIG. 13

MUFFLER

Inspect and replace corroded muffl er as it could create a fi re hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each mowing season or after every 100 hours of operation, whichever occurs fi rst. Spark plug type and gap setting are shown in the

“PROD UCT SPEC I FI C A TIONS” section of this manual.

CLEANING

IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER

HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN

THE UNDERSIDE OF YOUR MOWER AFTER EACH USE.

CONTAINER

FIG. 12

5. Slowly pour oil down the oil fi ll spout, stopping every few ounces to check the oil level with the dipstick.

6. Stop adding oil when you reach the FULL mark on the dipstick. Wait a minute to allow oil to settle.

7. Continue adding small amounts of oil, rechecking the dipstick until oil level settles at FULL. DO NOT overfi ll, or engine will smoke heavily from the muffl er on startup.

8. Always be sure to retighten dipstick before starting engine.

9. Re con nect spark plug wire to spark plug.

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

• Clean the underside of your lawn mower by scraping to remove build-up of grass and trash.

• Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life.

• Keep fi nished surfaces/wheels free of gasoline, oil, etc.

• We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffl er, air fi lter and carburetor are covered to keep water out.

Water in engine can result in shortened engine life.

AIR FILTER (See Fig. 13)

Your engine will not run properly and may be damaged by using a dirty air fi lter. Replace the air fi lter cartridge every

100 hours of op er a tion or every season, which ev er occurs fi rst. Service air cleaner more often under dusty conditions.

11

CLEAN UNDER DRIVE COVER

Clean under drive cover at least twice a season. Scrape underside of cover with putty knife or similar tool to remove any build-up of trash or grass on underside of drive cover.

SERVICE AND ADJUSTMENTS

CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

1. Release control bar and stop engine.

2. Make sure the blade and all moving parts have completely stopped.

3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug.

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See “TO ADJUST CUTTING HEIGHT” in the Operation section of this manual.

REAR DEFLECTOR

The rear defl ector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator's mowing position. If the defl ector becomes damaged, it should be replaced.

TO REMOVE DRIVE BELT (See Fig. 14)

1. Remove drive cover and belt keeper.

2. Remove belt from gearcase pulley by push ing down on pulley and rolling belt off it.

3. Turn lawn mower on its side with air fi lter and car bu re tor down.

4. Remove blade and debris shield.

5. Remove belt from engine pulley on crankshaft.

DRIVE

COVER

TO ADJUST HANDLE (See Figs. 15 thru 17)

The handle can be mounted in a high or low position. The mounting holes in the bottom of lower handle are off center for raising or lowering the handle.

1. Remove upper handle and all wire tie(s) securing cable(s) to lower handle.

2. Remove hairpin cotters from lower handle bracket mount ing pin.

3. Squeeze lower handle in to remove from mounting pins.

4. Turn lower handle over to raise or lower handle.

5. Squeeze lower handle in and po si tion holes onto mount ing pins on handle bracket.

6. Reassemble upper handle and all parts removed from lower handle.

SQUEEZE

TO ADJUST

LOWER HANDLE

MOUNTING PIN

HANDLE

BRACKET

HAIRPIN

COTTER

FIG. 15

BELT

KEEPER

PUSH

DOWN

MOWING

POSITION

MOWING

POSITION

BELT

FIG. 14

TO REPLACE DRIVE BELT (See Fig. 14)

1. Install new belt on engine pulley.

2. Reinstall debris shield and blade.

3. Return mower to upright po si tion.

4. Install new belt on gearcase pulley.

5. Reinstall belt keeper and drive cover.

NOTE: Always use factory approved belt to assure fi t and long life.

12

HAIRPIN

COTTER

MOUNTING

PIN

LOW POSITION

HANDLE

BRACKET

HIGH POSITION

FIG. 16

SERVICE AND ADJUSTMENTS

ROTATE

FIG. 17

LOWER

HANDLE

ENGINE

ENGINE SPEED

Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that the engine is running too fast or too slow, take your lawn mower to an authorized service center for repair and adjustment.

CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your lawn mower to an authorized service center for repair and/or adjustment.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR,

WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.

OVER SPEED ING THE ENGINE ABOVE THE FACTORY HIGH

SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE

ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,

CONTACT YOUR NEAREST AUTHORIZED SER VICE CEN TER,

WHICH HAS PROPER EQUIP MENT AND EXPERIENCE TO

MAKE ANY NEC ES SARY ADJUSTMENTS.

STORAGE

Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.

LAWN MOWER

When lawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1. Clean entire lawn mower (See “CLEANING” in the

Maintenance section of this manual).

2. Lubricate as shown in Maintenance section of this manual.

3. Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

4. Touch up all rusted or chipped paint surfaces; sand lightly before painting.

OPERATOR

PRES ENCE

CONTROL

BAR

SQUEEZE

TO ADJUST

LOWER HANDLE

FIG. 18

FOLD

FORWARD

FOR

STORAGE

MOWING

POSITION

HANDLE (See Figs. 18 and 19)

You can fold your lawn mower handle for storage.

1. Squeeze the bottom ends of the lower handle toward each other until the lower handle clears the handle bracket, then move handle forward.

2. Loosen upper handle mounting bolts enough to allow upper handle to be folded back.

IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE

OR TRANSPORTATION, BE SURE TO FOLD THE HANDLE AS

SHOWN OR YOU MAY DAMAGE THE CONTROL CABLES.

• When setting up your handle from the storage position, the lower han dle will automatically lock into mow ing position.

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

13

FIG. 19

STORAGE

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS

FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH

AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK

DURING STORAGE. ALCOHOL BLENDED FUELS (CALLED

GASOHOL OR USING ETHANOL OR METHANOL) CAN

ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND

FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS

CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE

IN STORAGE.

• Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during stor age.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3. Pull starter handle slowly a few times to distribute oil.

4. Replace with new spark plug.

BATTERY

Disconnect the battery from the engine connector and charge battery 48 hours.

OTHER

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your unit indoors and cover it to give protection from dust and dirt.

• Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your unit to rust.

IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND

EXHAUST AREAS ARE STILL WARM.

CAUTION: Never store the lawn mower with gasoline in the tank inside a build-

ing where fumes may reach an open fl ame or spark. Allow the engine to cool before storing in any enclosure.

14

TROUBLESHOOTING POINTS

PROBLEM CAUSE CORRECTION

Does not start

1. Dirty air fi lter. 1. Clean/replace air fi lter.

2. Out of fuel. 2. Fill fuel tank.

3. Stale fuel. 3. Empty fuel tank and refi ll tank with fresh,

clean gasoline.

4. Water in fuel. 4. Empty fuel tank and refi ll tank with fresh,

clean gasoline.

5. Spark plug wire is disconnected. 5. Connect wire to plug.

6. Bad spark plug. 6. Replace spark plug.

7. Loose blade or broken blade adapter. 7. Tight en blade bolt or replace blade adapter.

8. Control bar in released position. 8. Depress control bar to handle.

9. Control bar defective. 9. Replace control bar.

10. Fuel valve lever (if equipped) in OFF position. 10. Turn fuel valve lever to the ON position.

11. Weak battery (if equipped). 11. Charge battery.

12. Disconnected battery connector (if equipped). 12. Connect battery to engine.

Loss of power

1. Rear of lawn mower housing or cutting 1. Raise cutting height.

blade dragging in heavy grass.

2. Cutting too much grass. 2. Raise cutting height.

3. Dirty air fi lter. 3. Clean/replace air fi lter.

4. Buildup of grass, leaves and trash under 4. Clean underside of mower housing. mower.

5. Too much oil in engine. 5. Check oil level.

6. Walking speed too fast. 6. Cut at slower walking speed.

Poor cut –

uneven

Excessive

vibration

1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

2. Wheel heights uneven. 2. Set all wheels at same height.

3. Buildup of grass, leaves and trash under 3. Clean underside of mower housing. mower.

1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.

2. Bent engine crankshaft. 2. Contact a qualifi ed service center.

Starter rope

hard to pull

1. Engine fl ywheel brake is on when control 1. Depress control bar to upper handle before

bar is released. pulling starter rope.

2. Bent engine crankshaft. 2. Contact a qualifi ed service center.

3. Blade adapter broken. 3. Replace blade adapter.

4. Blade dragging in grass. 4. Move lawn mower to cut grass or other

hard surface before starting.

Grass catcher 1. Cutting height too low. 1. Raise cutting height.

not fi lling 2. Lift on blade worn off. 2. Replace blade.

(if so equipped) 3. Catcher not venting air. 3. Clean grass catcher.

Hard to push 1. Grass is too high or wheel height is too low. 1. Raise cutting height.

2. Rear of lawn mower housing or cutting 2. Raise rear of lawn mower housing one (1)

blade dragging in heavy grass. setting higher.

3. Grass catcher too full. 3. Empty grass catcher.

4. Handle height position not right for you. 4. Adjust handle height to suit.

Loss of drive 1. Belt wear. 1. Check/replace drive belt.

or slowing of 2. Belt off of pulley. 2. Check/reinstall drive belt.

drive speed 3. Drive cable worn or broken. 3. Replace drive cable.

4. “Loose” drive control system. 4. Adjust drive control.

15

ROTARY LAWN MOWER - - MODEL NUMBER 67522ES (96143001200) - PRODUCT NUMBER 961 43 00-12

ROTARY LAWN MOWER - - MODEL NUMBER

67522ES

(96143001200) - PRODUCT NUMBER 961 43 00-12

KEY PART

NO. NO. DESCRIPTION

KEY PART

NO. NO. DESCRIPTION

1 532 19 64-03 Upper Handle (Includes Foam Grip)

2 532 18 96-86 Key Start Switch / Engine Zone Control Cable

3 532 12 51-62 Bracket, Upstop

4 532 16 66-49 Mulcher Plug

5 532 06 64-26 Wire Tie

6 532 19 18-56 Handle Knob

7 532 75 06-34 Screw

8 532 19 70-19 Control Bar

9 532 19 36-79 Rear Door Assembly (Includes Springs)

10 532 12 84-15 Pop Rivet

11 532 15 00-50 Screw, Self-Tapping #10-24 x 5/8

12 532 05 45-83 Screw, Hex Hex Head, Sems 1/4-20 x 1/2

14 532 19 70-76 Back Plate

15 532 13 88-60 Side Baffl e

16 532 17 71-33 Discharge Baffl e

17 532 14 89-41 Rear Baffl e

18 532 13 20-04 Keps Locknut 1/4-20

19 532 19 47-88 Rope Guide

20 532 18 90-08 Rear Skirt

21 532 17 09-38 Spring, Rear Door, LH

24 532 17 09-39 Spring, Rear Door, RH

25 532 14 52-12 Nut, Hex, Flanged

26 532 18 41-93 Bolt, Rear Door

27 532 40 29-48 Wheel, Rear

28 532 14 27-48 Bolt, Shoulder 3/8-16 x 1

29 532 06 16-51 Washer, Belleville

30 532 19 60-21 Axle Arm Assembly

31 532 19 06-22 Selector Knob

32 532 19 84-56 Selector Spring

33 532 19 70-29 Mulcher Door

34 532 14 66-30 Spacer

35 532 15 50-47 Wheel Adjusting Bracket

36 532 17 57-35

37 532 15 00-78

38 532 19 70-30

39 532 19 71-50

40 532 19 71-51

Hinge Bracket Assembly

Screw, Sems, Thread Cutting 5/16-18 x 3/4

Discharge Defl ector

Handle Bracket Assembly, LH

Handle Bracket Assembly, RH

41 532 15 04-06 Bolt, Engine, Dogpoint

42 532 19 30-00 Spring, Torsion

43 873 80 04-00 Nut, Hex, Nylock

44 532 19 63-98 Kit, Lawn Mower Housing

(Includes Key Numbers 14, 15 and 51)

45 532 17 56-50 Rod, Hinge

46 532 19 40-37 Blade Adapter / Pulley

47 532 14 11-14 Blade, 22"

48 532 85 10-74 Washer, Hardened

49 532 85 02-63 Washer, Helical

50 532 85 10-84 Screw, Machine, Hex Head 3/8

51 532 17 00-31 Front Baffl e

52 532 10 73-39 Danger Decal

53 817 60 04-06 Screw

54 532 08 83-48 Washer

55 532 75 15-92 Locknut, Hex 3/8-16

56 532 08 86-52 Screw, Hinge 1/4-20 x 1-1/4

57 532 05 17-93 Hairpin Cotter

58 532 40 34-33 Lower Handle

59 532 19 15-74 Handle Bolt

60 874 76 06-12 Bolt

61 532 75 15-92 Nut, Hex

62 532 19 93-14 Debris Shield

63 532 19 23-25 Screw, Debris Shield

64 - - - Engine, Briggs & Stratton, Model Number 125K05

(Order parts from Engine manufacturer)

65 532 19 74-80 O-Ring

67 532 40 16-07 Clip, Packaging

69 532 19 79-91 Clip, Cable

70 532 18 27-48 Foam Grip

71 532 19 09-39 Mounting Bracket, Debris Shield

72 532 18 22-27 Screw

73 532 19 71-62 Belt Keeper

74 532 18 22 28 Nut, Hex

75 532 18 61-59 Screw, Phillips Head

76 532 18 03-31 Key

- - 532 16 23-00 Warning Decal (not shown)

- - 532 40 05-10 Owner's Manual, English/French

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

ROTARY LAWN MOWER - - MODEL NUMBER 67522ES (96143001200) - PRODUCT NUMBER 961 43 00-12

ROTARY LAWN MOWER - - MODEL NUMBER

67522ES

(96143001200) - PRODUCT NUMBER 961 43 00-12

KEY PART

NO. NO. DESCRIPTION

1 532 19 71-94 Drive Control Assembly (Includes Cable)

2 532 19 57-61 Cover, Drive Control, Top

3 532 18 73-53 Pulley

4 532 19 00-39 Lever, Drive Control

5 532 19 57-62 Cover, Drive Control, Bottom

6 532 18 16-98 Screw, Torx Head #8 x 5/8

7 532 40 07-23 Mounting Bracket, Drive Control

8 532 19 71-95 Cable, Drive Control

9 532 18 62-97 Cap, Drive Control, Bottom

10 532 18 90-74 Decal, Drive Control

11 532 40 05-43 Wheel & Tire Assembly

12 812 00 00-58 E-Ring

13 532 75 00-03 Gear, Pinion

14 532 18 94-03 Dust Cover

15 532 19 10-17 Drive Pawl

16 532 06 77-25 Washer, Flat 3/8

17 532 19 10-39 Bearing, Wheel Adjuster

18 532 19 64-01 Selector Knob

23 532 08 86-52 Screw

24 532 19 17-30 Nut, Hex

25 532 19 73-86 Belt Guide Bracket

26 532 19 23-25 Screw

27 532 17 52-62 Pan Head Tapping Screw #10-24 x 2-3/4

28 532 19 73-70 Drive Cover

29 532 08 39-23 Locknut, Hex

31 532 14 18-41 Screw, Trimplate, Top

32 532 19 40-18 Drive Pulley

33 532 19 68-57 V-Belt

34 532 18 61-53 Trimplate

35 532 19 51-10 Kit, Wheel Adjuster, LH

(Includes Knob and Bearing)

36 532 19 16-36 Gearcase Assembly, Complete

37 532 18 95-89 Battery

KEY PART

NO. NO. DESCRIPTION

38 873 80 04-00 Locknut, Hex 1/4-20

39 532 18 62-37 Box, Battery

40 532 19 28-49 Spring

41 532 19 51-07 Kit, Wheel Adjuster, RH

(Includes Knob and Bearing)

42 817 41 13-08 Screw, Battery Box

43 532 19 00-97 Charger, Battery

44 532 17 55-51 Screw, Shoulder, Hex Head

#10 x 9/32 x 1/16

54 532 40 11-89 Grassbag Assembly

55 532 08 60-12 Driveshaft Cover

57 532 18 96-80 Frame, Grassbag

61 532 19 68-86 Case, Upper

62 532 19 70-57 Shaft, Output

63 532 18 35-08 Seal, Output Shaft

64 532 18 35-11 Bushing

65 532 18 35-09 Washer

66 532 18 35-14 Seal, Worm Shaft

67 532 18 35-06 Bearing, Ball

68 532 18 34-99 Gear, 27 Teeth

69 532 19 68-84 Fixed Dog Clutch

70 532 18 35-05 Wireform

71 532 19 68-83 Movable Dog Clutch

72 532 19 68-82 Fork

73 532 18 35-13 Screw, Case

74 532 19 68-81 Case, Lower

75 532 19 68-80 Seal, Lever

76 532 19 68-79 Lever

77 532 19 68-78 Screw, Lever

78 532 19 68-77 Spring

79 532 18 35-02 Shaft, Worm

*

Use Dow Corning #709 to reseal Gear Case Halves.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

SECTION 1: LIMITED WARRANTY

Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty

Period” of the product as set forth below:

Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held prod uct.

3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds)

2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area walks, and ground engaging commercial equipment.

2 Year NON-COMMERCIAL Warranty: Automatic Mower, Riding lawn mowers, yard and garden tractors, walk behind mowers, tillers, chain saws, trimmers, brushcutters, clearing saws, snow blowers, handheld blowers, backpack blowers, hedge trimmers, electrical products and power-assist collection systems for non com mer cial, nonprofessional, noninstitutional or nonincome producing use, except as herein stated.

Emission control system components necessary to comply with CARB-TIER-II and EPA regulations, except for those components which are part of engine systems manufactured by third party engine manufacturers for which the purchaser has received a separate warranty with product information supplied at time of purchase.

1 Year Warranty: Power cutters, stump grinder, pole pruners and pole saws for non-commercial, non-professional, non-institutional or non-income producing use. All trimmers, brushcutters, clearing saws, hovering trimmers, stick edgers, backpack blowers, hand held blowers, hedge trimmers, power-assist collection systems used for commercial, institutional, professional or income producing purposes or use.

Batteries have a one-year prorated limited warranty with 100% replacement during the fi rst 6 months.

90 Day Warranty: Automatic Mower, Chain saws, power cutters, stump grinders, pole saws, pole pruners, snow throwers, model series 580 & 600 walk-behind mowers and commercial turf equipment or any

Husqvarna product used for commercial, institutional, professional, or income producing purposes or use except as otherwise provided herein.

Husqvarna Safety Apparel carries a 90-day warranty from the date of the customer’s original purchase for defects in material and workmanship. Normal wear, tear or abuse is not covered under warranty. Product must be returned to Charlotte with a warranty claim form. All care and maintenance instructions must be followed as stated by the manufacturer on the care label. The fi t of the protective apparel/boot is not covered under warranty.

30 Day Warranty: Replacement parts, accessories including bars and chains, tools and display items.

SECTION 2: HUSQVARNA’S OBLIGATIONS UNDER THE WARRANTY

Husqvarna will repair or replace defective components without charge for parts or labor if a component fails because of a defect in material or workmanship during the warranty period.

SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY

The following items are not covered by this warranty:

(1)Normal customer maintenance items which become worn through normal regular use, including, but

not limited to, belts, blades, blade adapters, bulbs, fi lters, guide bars, lubricants, rewind springs, saw

chain, spark plugs, starter ropes and tines;

(2)Natural discoloration of material due to ultraviolet light;

(3)Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective

manufacturer’s warranty as provided in writing with the product information supplied at the time of pur-

chase; all claims must be sent to the appropriate manufacturer;

(4)Lawn and garden attachments are covered by a third party which gives a warranty, all claims for war-

ranty should be sent to the manufacturer; and

(5)Emission Control System components necessary to comply with CARB-TIER-II and EPA regulations

which are manufactured by third party engine manufacturer.

WARRANTY STATEMENT

SECTION 4: EXCEPTIONS AND LIMITATIONS

This warranty shall be inapplicable to defects resulting from the following:

(1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust,

corrosion, or any adverse reaction due to incorrect storage or use habits;

(2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruc-

tion sheet furnished by Husqvarna;

(3)Alterations or modifi cations that change the intended use of the product or affects the product’s per-

formance, operation, safety, or durability, or causes the product to fail to comply with any applicable

laws; or:

(4)Additional damage to parts or components due to continued use occurring after any of the above.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF

THE PUR CHAS ER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT

TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE ON THESE PRODUCTS IS LIMITED IN DURATION TO

THE WARRANTY PERIOD AS DEFINED IN THE LIMITED WARRANTY STATEMENT. HUSQVARNA RE-

SERVES THE RIGHT TO CHANGE OR IMPROVE THE DESIGN OF THE PRODUCT WITHOUT NO TICE,

AND DOES NOT ASSUME OBLIGATION TO UPDATE PREVIOUSLY MANUFACTURED PROD UCTS.

Some states do not allow the exclusion of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state.

SECTION 5: CUSTOMER RESPONSIBILITIES

The product must exhibit reasonable care, maintenance, operation, storage and general upkeep as written in the maintenance section of the Owner’s/Operator’s manual. Should an operational problem or failure occur, the product should not be used, but delivered as is to an authorized Husqvarna dealer for evaluation. Proof of purchase, as explained in section 6, rests solely with the customer.

SECTION 6: PROCEDURE TO OBTAIN WARRANTY CONSIDERATION

It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly fi lled out and mailed to Husqvarna Forest & Garden Company. This card should be mailed within ten (10) days from the date of purchase in order to confi rm the warranty and to facilitate post-sale service.

Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address of the selling dealer.

To obtain the benefi t of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. The product must be delivered at the owner’s expense. Pick-up and delivery charges are not covered by this warranty. An authorized Husqvarna dealer can be normally located through the “Yellow

Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area.

HUSQVARNA

7349 Statesville Road

Charlotte, NC 28269

531 83 81-23 2002

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Table of contents