Whirlpool BAAN 134 PS (UK) Operating instructions


Add to my manuals
12 Pages

advertisement

Whirlpool BAAN 134 PS (UK) Operating instructions | Manualzz
Operating Instructions
REFRIGERATOR/FREEZER COMBINATION
Contents
Installation, 2-3
GB
Positioning and connection
Reversible doors
English, 1
Description of the appliance, 4
Overall view
Accessories, 5
Start-up and use, 6-7
Starting the appliance
Chiller system
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 8
BAAN
BAAN
BAAN
BAAN
BAAN
134
134
134
134
134
S
X
PS
G
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Defrosting the appliance
Replacing the light bulb
Precautions and tips, 9
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 10
Assistance, 11
GB
Installation
GB
! Before placing your new appliance into operation please
read these operating instructions carefully. They contain
important information for safe use, for installation and for
care of the appliance.
Your appliance is supplied with a 13amp fused plug that
can be plugged into a 13amp socket for immediate use.
Before using the appliance please read the instructions
below.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free
room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of
the appliance and any furniture above it, and at least 5
cm between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied
in the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the
refrigerator by tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to
the electricity mains. Before inserting the plug into the
electrical socket ensure the following:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the bottom left side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values
indicated on the data plate located on the bottom left
side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (see Assistance). Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these
safety measures not be observed.
2
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved
fuse to BS 1362 should always be used and the fuse
cover re-fitted.
If the fuse cover is lost, the plug must not be used until
a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking or the
colour that is embossed in words on the base of the plug.
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a longer cable
or to re-route the mains cable through partitions, units
etc. please ensure that either:
- The plug is replaced by a fused 13amp rewireable plug bearing the BSI mark of
approval.
or
- The mains cable is wired directly into a
13amp cable outlet, controlled by a
switch (in compliance with BS 5733)
which is accessible without moving the
appliance.
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit
your socket. The cable should be cut as close as
possible to the moulded plug.
Remove the fuse.
WARNING:
To avoid a shock hazard do not insert the discarded
plug into a socket anywhere else.
Reversible doors
Fitting a new plug
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE...
Green and Yellow
Blue
Brown
GB
1
- Earth
- Neutral
- Live
As the colours of the wires in the mains lead may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
- Connect Green and Yellow wire to terminal marked
or coloured Green and Yellow.
'E' or
- Connect Brown wire to terminal marked 'L' or
coloured red or brown.
- Connect Blue wire to terminal marked 'N' or
coloured Black or Blue.
If a 13amp plug (BS 1363) is used it must be
fitted with a 13amp fuse.
2
3
If you are in any doubt about the electrical
supply to your machine, consult a qualified
electrician before use.
CE Marking certifies that this appliance conforms to
the following EEC directives :
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC
& 93/68/EEC
4
∅ 3mm
5
3
Description of the
appliance
GB
Overall view
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not
directly represent the appliance purchased. For more complex features, consult the following pages.
TEMPERATURE
REGULATING
Knob
LAMP
(see Maintenance)
MULTI-USE* bin
SHELVES•
Removable lidded
shelf with EGG TRAY
Removable
multipurpose
SHELVES
FLEX COOL BOX
for MEAT and
CHEESE*
FRUIT and
VEGETABLE bin
Ice3 ice tray•
FREEZER and
STORAGE
compartment
Ice3 ice tray•
STORAGE
compartment•
Levelling FEET
• Varies by number and/or position.
* Available only on certain models.
4
BOTTLE shelf
Accessories
1
2
SHELVES•: with or without grill.
Due to the special guides the
shelves are removable and the
height is adjustable (see
diagram), allowing easy storage
of large containers and food.
Height can be adjusted without
complete removal of the shelf.
MULTI-USE* bin: to store food (such as cold meats)
for a long time and also prevent odours from lingering
in the refrigerator.
FLEX COOL BOX*
This is the new box to keep meat, fish and cheese
fresh. When positioned in the “lower” part of the fridge
compartment, it is ideal for meat and fish; when moved
to the “top” part of the fridge, it is perfect for cheese. It
can be taken out of the fridge when it is not needed.
PLAY ZONE*: Thanks to the new “Play Zone” bottle
rack, you can cool several bottles, cans and energy
drinks quickly to have them constantly at hand.
GRAFFITI*: this is the marker kit
which makes your Indesit
refrigerator more colourful and fun.
With these markers, you can write,
leave messages and draw on the
doors and sides of the refrigerator.
GRAFFITI is extremely easy and
convenient to use; after having
written or drawn, you will be able
to easily and quickly erase the
drawings using a dry cloth or an
ordinary whiteboard eraser. Do not use the pen holder to
erase the ink. This could permanently damage the
product and/or the parts included in the GRAFFITI kit.
WARNING:
the GRAFFITI marker kit was studied, designed and
tested to be used exclusively on the doors and sides of
those products belonging to the Indesit range with
which it is sold.
Therefore, do not use:
- your Graffiti markers on other Indesit refrigerators and/
or other brands;
- your Graffiti markers on other appliances;
- other types or makes of markers on your Indesit
refrigerator;
If you do not follow the instructions above, it could result
in colour stains and/or permanent marks.
Children should only use the markers under adult
supervision.
Indesit Company S.p.A shall not be liable for any effects
resulting from incorrect use of the GRAFFITI kit.
If the “Play Zone” is placed on the glass shelf, you can
store large and medium sized bottles on it simply by
laying the bottle on the flat rack. This is ideal for storing
wine bottles. When folded and secured in place on either
side of the shelf, the rack can be used to store cans (at
the top), energy drinks (in the centre) and other cans
and energy drinks can be rested horizontally on the
remaining part of the shelf. When placing cans (onto the
Play zone rack), make sure they do not touch the back
of the refrigerator interior.
The “Play Zone” can be used just like a normal shelf
(when placed flat) and moved up or down along the
fridge walls together with the rest of the shelf. It can be
washed easily, and is also dishwasher safe. The ideal
position for the Play zone rack is the central shelf.
• Varies by number and/or position.
* Available only on certain models.
5
GB
Start-up and use
GB
Starting the appliance
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the
compartments and accessories well with lukewarm
water and bicarbonate.
1. Insert the plug into the socket and ensure that the
internal light illuminates.
2. Turn the TEMPERATURE ADJUSTMENT knob to an
average value. After a few hours you will be able to
put food in the refrigerator.
Setting the temperature
The temperature inside the refrigerator compartment
automatically adjusts itself according to the position of
the thermostat knob.
= warmest
= coldest
We recommend, however, a medium position.
The cooling section of the refrigerator is located inside
the back wall of the refrigerator compartment for
increased space and improved aesthetics. During
operation, the back wall will be covered in frost or water
droplets depending on whether the compressor is
operating or paused. Do not worry, the refrigerator is
functioning normally.
It is recognizable due to the presence of the mechanism
on the top part of the refrigerator compartment (see
diagram). The Aircooler maintains a constant fridge
temperature to keep food fresher for longer and will
quickly restore the temperature to the correct level, even
if the door is opened frequently: the blown air (A) is
cooled when it comes into contact with the cold wall,
whereas the hotter air (B) is sucked up (see diagram).
The back wall may be covered in frost or droplets of
water, depending on whether the compressor is in
operation or whether it is paused.
Static
Models without the Aircooler have the cooling section in
the internal back wall of the compartments. The wall will
be covered in frost or water droplets depending on
whether the compressor is operating or paused: both
cases are normal. If the TEMPERATURE ADJUSTMENT
knob has been set on high values with large quantities
of food and with a high ambient temperature, the
appliance can operate continuously, resulting in
excessive frost formation and excessive energy
consumption: compensate for this by shifting the knob
towards lower values (defrosting will occur
automatically).
In static appliances, the air circulates in a natural way:
the colder air tends to move downwards as it is heavier.
The food should be stored as follows:
)RRG
Fresh fish and meat
Fresh cheese
Chiller system
The appliance comes with one of the chiller systems
described below: take note of your system in order to
determine the most efficient food storage method.
Aircooler
Cooked food
On any shelf
Salami, bread loaf,
chocolate
On any shelf
Fruit and vegetables
In the fruit and vegetable bins
Eggs
On the shelf provided
Butter and margarine On the shelf provided
Bottles, drinks, milk
B
A
6
$UUDQJHPHQWLQVLGHWKH
UHIULJHUDWRU
Above the fruit and vegetable
bins
Above the fruit and vegetable
bins
On the shelf provided
Using the refrigerator to its full potential
• Use the TEMPERATURE ADJUSTMENT knob to adjust
the temperature (see Description).
• Place only cold or lukewarm foods in the
compartment, not hot foods (see Precautions and
tips).
• Remember that cooked foods do not last longer than
raw foods.
• Do not store liquids in open containers. They will
increase humidity in the refrigerator and cause
condensation to form.
Using the freezer to its full potential
2. Take care not to exceed the level indicated (MAX
WATER LEVEL). Excess water prevents the ice cubes
from dispensing (if this happens, wait for the ice to
melt and empty the tray).
3. Turn the tray 90°: due to the connected compartments
each mould fills with water (see diagram).
4. Close the opening with the lid provided and put the
tray back, placing the top part in the corresponding
housing and allowing it to drop in again.
5. When the ice has formed (minimum time
approximately 8 hours) knock the tray against a hard
surface and wet the outside so that the ice cubes
come loose and take them out through the opening.
• Do not re-freeze food that is defrosting or that has
already been defrosted. These foods must be cooked
and eaten (within 24 hours).
• Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted.
Fresh food must be stored in the top FREEZER and
STORAGE compartment where the temperature drops
below -18°C and guarantees rapid freezing.
• Do not place glass bottles which contain liquids, and
which are corked or hermetically sealed in the freezer
because they could break.
• The maximum quantity of food that may be frozen daily
is indicated on the plate containing the technical
properties located on the bottom left side of the
refrigerator compartment (for example: Kg/24h: 4)
MAX
WATER LEVEL
MAX
WATER LEVEL
! Do not open the door during freezing.
MAX
WATER LEVEL
! If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature
inside the freezer, ensuring that foods are conserved for
at least 9 -14 hours.
! If the room temperature drops below 14°C for an
extended period of time, the ideal temperature will not
be reached in the freezer compartment and food
preservation will be reduced.
Ice3 ice tray
The fact that they are situated on the top part of the freezer
drawers ensures greater cleanliness: the ice no longer comes
into contact with the food placed inside the freezer
compartment; furthermore, the dripping of the water during
filling is avoided (a lid to cover up the hole after filling with
water is also provided).
1. Pull out the tray by pushing it up.
Check that the tray is ompletely empty and fill it with
water through the opening provided.
7
GB
Maintenance and care
GB
Switching the appliance off
Defrosting the freezer compartment
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply.
It is not sufficient to set the temperature adjustment
knobs on (appliance off) to eliminate all electrical
contact.
Remove frost regularly using the special scraper
provided. If the frost layer is greater than 5 mm, it is
necessary to defrost manually:
Cleaning the appliance
• The external and internal parts, as well as the rubber
seals may be cleaned using a sponge that has been
soaked in lukewarm water and bicarbonate of soda or
neutral soap. Do not use solvents, abrasive products,
bleach or ammonia.
• The removable accessories may be soaked in warm
water and soap or dishwashing liquid. Rinse and dry
them carefully.
• The back of the appliance may collect dust which can
be removed by delicately using the hose of a vacuum
cleaner set on medium power. The appliance must be
switched off and the plug must be pulled out before
cleaning the appliance.
1. Set the TEMPERATURE ADJUSTMENT knob to the
position .
2. Wrap frozen foods in newspaper and place them in
another freezer or in a cool place.
3. Leave the door open until the frost has melted
completely. This can be made easier by placing
containers with lukewarm water in the freezer
compartment.
4. Clean and dry the freezer compartment carefully
before switching the appliance on again.
5. Certain appliances are
fitted with the DRAIN
SYSTEM to lead the water
outside: insert the scraper
into the slot provided at
the bottom and let the
water flow into a container
(see diagram).
Avoiding mould and unpleasant odours
• The appliance is manufactured with hygienic materials
which are odour free. In order to maintain an odour free
refrigerator and to prevent the formation of stains, food
must always be covered or sealed properly.
• If you want to switch the appliance off for an extended
period of time, clean the inside and leave the doors
open.
Defrosting the appliance
! Follow the instructions below.
Do not speed up the defrosting process by using any
devices or tools other than the scraper provided, you
may damage the refrigeration circuit.
2. Wait for approximately 2 hours, i.e. until the ideal
storage conditions have been restored, before placing
food in the freezer compartment.
Replacing the light bulb
To replace the light bulb in the refrigerator compartment,
pull out the plug from the electrical socket. Follow the
instructions below.
Access the light bulb by removing the cover as
indicated in the diagram.
Replace it with a similar light bulb within the power
range indicated on the cover (15W or 25W).
Defrosting the refrigerator compartment
The refrigerator has an automatic defrosting function:
water is ducted to the
back of the appliance by a
special discharge outlet
(see diagram) where the
heat produced by the
compressor causes it to
evaporate. It is necessary
to clean the discharge
hole regularly so that the
water can flow out easily.
8
1
1
2
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE..
General safety
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
• The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Do not touch the appliance with bare feet or with wet or
moist hands and feet.
• WARNING: do not damage the refrigerant circuit.
• Do not touch the internal cooling elements: this could
cause skin abrasions or frost/freezer burns.
• When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
• Before cleaning and maintenance, always switch off the
appliance and disconnect it from the electrical supply. It
is not sufficient to set the temperature adjustment knobs
on (appliance off) to eliminate all electrical contact.
• In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
• WARNING: do not use electrical or machanical devices
or tools other than the special scraper provided inside
the compartments.
• Do not put ice cubes taken directly from the freezer into
your mouth.
Disposal
GB
• Observe local environmental standards when
disposing packaging material for recycling purposes.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on
human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the
appliance it must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
Respecting and conserving the
environment
• Install the appliance in a fresh and well-ventilated
room. Ensure that it is protected from direct sunlight
and do not place it near heat sources.
• Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
• Do not fill the appliance with too much food:
cold air must circulate freely for food to be preserved
properly. If circulation is impeded, the compressor will
work continuously.
• Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
• Defrost the appliance if ice forms (see Maintenance).
A thick layer of ice makes cold transference to food
products more difficult and results in increased
energy consumption.
• Regularly check the door seals and wipe clean to
ensure they are free of debris and to prevent cold air
from escaping (see Maintenance).
• Do not allow children to tamper with the controls or play
with the appliance. Under no circumstance should they
be allowed to sit on the bins or to hang from the door.
• Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
9
Troubleshooting
GB
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
Malfunctions:
Possible causes / Solutions:
The internal light does not illuminate.
• The plug has not been inserted into the electrical socket, or not far
enough to make contact, or there is no power in the house.
The refrigerator and the freezer do not •
cool well.
•
•
•
•
The doors do not close properly or the seals are damaged.
The doors are opened too frequently.
The TEMPERATURE ADJUSTMENT knob is not in the correct position
The refrigerator or the freezer have been over-filled.
The atmospheric temperature of the area surrounding the appliance is
lower than 14°C.
The food inside the refrigerator is
beginning to freeze.
• The TEMPERATURE ADJUSTMENT knob is not in the correct
position.
• The food is in contact with the back inside wall of the refrigerator.
The AIR fan does not rotate.
• The refrigerator door is open.
• The AIR system is only activated automatically when it becomes
necessary to restore perfect operational conditions inside the
refrigerator compartment.
The motor runs continuously.
• The door is not closed properly or is continuously opened.
• The outside ambient temperature is very high.
• The thickness of the frost exceeds 2-3 mm (see Maintenance).
The appliance makes a lot of noise.
• The appliance has not been installed on a level surface (see
Installation).
• The appliance has been installed between cabinets that vibrate and
make noise.
• The internal refrigerant makes a slight noise even when the
compressor is off. This is not a defect, it is normal.
Some of the external parts of the
refrigerator become hot.
• These raised temperatures are necessary in order to avoid the
formation of condensation on certain parts of the product.
The back wall of the refrigerator unit
is covered in frost or droplets of
water.
• This shows the appliance is operating normally.
There is water at the bottom of the
refrigerator.
• The water discharge hole is blocked (see Maintenance).
10
Assistance
Before calling for Assistance:
• Check if the malfunction can be solved on your own (see Troubleshooting).
• If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service
Centre
model
serial number
Communicating:
• type of malfunction
• appliance model (Mod.)
• serial number (S/N)
This information can be found on the data
plate located on the bottom left side of the
refrigerator compartment.
Mod. RG 2330
220 - 240 V-
TI
50 Hz
Cod.
150 W
75
Total 340
Net
Gross
Gross
Util
Bruto
Bruto
Utile
Brut
Brut
Compr. R 134 a
Test Pressure
HIGH-235
Syst.
P.S-I. LOW 140
Kompr. kg 0,090
Made in Italy 13918
93139180000
W Fuse
S/N 704211801
A
Gross
Bruto
Brut
Max 15 w
Capac
Class
Poder de Cong
Clase
Freez.
kg/24 h
4,0
N
Classe
Never call on unauthorized technicians and always refuse spare parts which are not originals.
11
GB
195052766.00
05/2005 - Xerox Business Services
GB
12

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement