filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\010COV.fm] HOME AUDIO SYSTEM Operating Instructions masterpage:Cov Getting Started Disc/USB Playback USB Transfer Tuner BLUETOOTH Gesture Control Sound Adjustment Other Operations Additional Information MHC-GT4D model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\020REG.fm] masterpage:Left WARNING To reduce the risk of fire, do not cover the ventilation opening of the appliance with newspapers, tablecloths, curtains, etc. Do not expose the appliance to naked flame sources (for example, lighted candles). To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing, and do not place objects filled with liquids, such as vases, on the appliance. As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Do not expose batteries or appliances with battery-installed to excessive heat, such as sunshine and fire. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area). This equipment has been tested and found to comply with the limits set out in the EMC regulation using a connection cable shorter than 3 meters. Indoor use only. CAUTION The use of optical instruments with this product will increase eye hazard. This appliance is classified as a CLASS 1 LASER product under IEC 608251:2007. This marking is located on the rear exterior. For customers in Europe Disposal of waste batteries and electrical and electronic equipment (applicable in the European Union and other European countries with separate collection systems) This symbol on the product, the battery or on the packaging indicates that the product and the battery shall not be treated as household waste. On certain batteries this symbol might be used in combination with a chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are added if the battery contains more than 0.0005% mercury or 0.004% lead. By ensuring these products and batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery and the electrical and electronic equipment will be treated properly, hand over these products at end-of- 2GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\020REG.fm] life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product or battery. Notice for customers: The following information is only applicable to equipment sold in countries applying EU Directives. This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Belgium, bijkantoor van Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem, Belgium. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents. Hereby, Sony Corp., declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/ 5/EC. For details, please access the following URL: http://www.compliance.sony.de/ masterpage:Right This Home Audio System is intended for audio and video playback of discs or USB devices, music streaming from an NFC-compatible smartphone or a BLUETOOTH device, and FM tuner. This system also supports karaoke. For customers in Australia and India Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) For customers in United Arab Emirates License and Trademark Notice is a trademark of DVD Format/ Logo Licensing Corporation. “DVD+RW”, “DVD-RW”, “DVD+R”, “DVD-R”, “DVD VIDEO”, and the “CD” logos are trademarks. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/ or other countries. 3GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\020REG.fm] This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft or an authorized Microsoft subsidiary. “WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation. This system incorporates Dolby* Digital. * Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. This system incorporates HighDefinition Multimedia Interface (HDMI™) technology. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. “BRAVIA” is a trademark of Sony Corporation. LDAC™ and LDAC logo are trademarks of Sony Corporation. The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android™ is a trademark of Google Inc. Google Play™ is a trademark of Google Inc. masterpage:Left Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. HTTP://WWW.MPEGLA.COM All other trademarks are trademarks of their respective owners. 4GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\020REG.fm] masterpage:Right In this manual, ™ and marks are not specified. About this manual This manual mainly explains operations using the remote control, but the same operations can also be performed using the buttons on the subwoofer having the same or similar names. Icons, such as , listed at the top of each explanation indicate the type of media that can be used with the function being explained. Some illustrations are presented as conceptual drawings, and may be different from the actual products. The items displayed on the TV screen may vary depending on the area. The default setting is underlined. The text enclosed in bracket ([--]) appears on the TV screen, and the text enclosed in double quotation mark (“--”) appears in the display panel. 5GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\030TOC.fm] masterpage:Left Table of Contents About this manual.................... 5 Unpacking................................. 8 Playable discs/files on Discs/ USB device ................................ 8 Websites for compatible devices.................................... 10 Guide to parts and controls .... 11 Getting Started Installing the system ...............14 Carrying the system ............... 20 Hooking up the system securely....................................21 Performing QUICK setup ........ 25 Changing the color system (Except for Latin American, European, and Russian models)................................... 25 Changing the display mode....................................... 25 Disc/USB Playback Basic playback ........................ 26 Other playback operations .... 27 Using play mode .................... 29 Restricting playback of the disc (Parental Control)............ 30 Viewing information of a disc and USB device........................31 Using the Setup Menu............ 32 USB Transfer Transferring music ................. 36 Tuner BLUETOOTH About the BLUETOOTH wireless technology ............... 39 Pairing this system with a BLUETOOTH device ................ 40 Playing music from a BLUETOOTH device ................. 41 One Touch BLUETOOTH Connection by NFC................. 42 Setting the BLUETOOTH audio codecs .......................... 43 Setting the BLUETOOTH standby mode ........................ 43 Setting the BLUETOOTH signal ...................................... 43 Using “SongPal” via BLUETOOTH............................ 44 Gesture Control Enjoying the Gesture Control.................................... 44 Using the Gesture Control during playback ..................... 45 Creating a party atmosphere (DJ EFFECT) ............................. 45 Changing the lighting effect ...................................... 46 Sound Adjustment Adjusting the sound .............. 46 Selecting the Virtual Football mode ...................................... 46 Adjusting the subwoofer level .........................................47 Creating your own sound effect .......................................47 Listening to the radio ............. 38 6GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\030TOC.fm] masterpage:Right Other Operations Using the Control for HDMI function .................................. 48 Using the Party Chain function .................................. 49 Singing along: Karaoke .......... 51 Enjoying the Party Light .........52 Using the Sleep Timer ............52 Using optional equipment .....52 Deactivating the buttons on the subwoofer (Child Lock).....53 Setting the automatic standby function.....................53 Updating the software ...........53 Additional Information Troubleshooting .....................54 Precautions .............................63 Specifications..........................65 Language code list .................67 Index ...................................... 69 7GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\040PLA.fm] Unpacking The discs must be in the following format: CD-ROM/-R/-RW in DATA CD format that contains the MP31)2), MPEG42)5) and Xvid files, and conforms to ISO 96606) Level 1/Level 2 or Joliet (extended format). DVD-ROM/-R/-RW/+R/+RW in DATA DVD format that contains the MP31)2), MPEG42)5) and Xvid files, and conforms to UDF (Universal Disk Format). The system will attempt to play back any data with the extensions above, even if it is not in MP3/WMA/AAC/ WAV/MPEG4/Xvid format. Playing this data may generate a loud noise which could damage your speaker system. Active subwoofer: SA-WGT4D (1) Speaker system: SS-GT4DB (2) Note When unpacking the carton, be sure to handle the subwoofer with two persons. Dropping the subwoofer may cause personal injury and/or property damage. Playable discs/files on Discs/USB device Playable Discs DVD VIDEO DVD-R/DVD-RW in DVD VIDEO format or video mode DVD+R/DVD+RW in DVD VIDEO format VIDEO CD (Ver. 1.0, 1.1, and 2.0 discs) Super VCD CD-R/CD-RW/CD-ROM in VIDEO CD format or super VCD format AUDIO CD CD-R/CD-RW in AUDIO CD format Playable files on Discs/USB device Music: MP3 files1)2) (.mp3), WMA files2)3) (.wma), AAC files2)3) (.m4a/ .mp4/.3gp), WAV files3)4) (.wav) Video: MPEG4 files2)5) (.mp4/.m4v), Xvid files (.avi) Notes Remote control (1) R03 (size AAA) batteries (2) FM lead antenna (1) AC power cord (mains lead) (1) Speaker stands (2) Speaker pads (8) Screws (6) AC plug adaptor (1) (supplied only for certain areas) The AC plug adaptor is not use in Chile. Use this plug adaptor in the countries where it is necessary. The MHC-GT4D consists of: masterpage:Left 1) MP3 (MPEG 1 Audio Layer 3) is a standard format defined by ISO/MPEG for compressed audio data. MP3 files must be in MPEG 1 Audio Layer 3 format. 2) Files with copyright protection (Digital Rights Management) cannot be played back by the system. 3) USB device only. 4) WAV files with extensible format are not supported. 5) MPEG4 files must be recorded in MP4 file format. Supported video codec and audio codec are as follows: Video codec: MPEG4 Simple Profile (AVC is not supported.) Audio codec: AAC-LC (HE-AAC is not supported.) 6) A logical format of files and folders on CD-ROMs, defined by ISO (International Organization for Standardization). Discs/files that cannot be played back You cannot play back the following discs BDs (Blu-ray Discs) CD-ROMs recorded in PHOTO CD format Data part of CD-Extra or Mixed CDs* 8GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\040PLA.fm] CD Graphics disc Super Audio CDs DVD Audio DATA CD/DATA DVD that is created in Packet Write format DVD-RAM DATA CD/DATA DVD which has not been correctly finalized CPRM (Content Protection for Recordable Media) compatible DVD-R/-RW recorded in Copy-Once programs A disc that has a non-standard shape (e.g., heart, square, star) A disc that has adhesive tape, paper, or a sticker attached to it You cannot play back the following files The video files which are larger than 720 (width) × 576 (height) pixels. The video files with a high width to length ratio. A WMA file in WMA DRM, WMA Lossless, or WMA PRO format. An AAC file in AAC DRM or AAC Lossless format. The AAC files which is encoded at 96 kHz. Files that are encrypted or protected by passwords. Files with DRM (Digital Rights Management) copyright protection. Some Xvid files that are longer than 2 hours. The MP3 PRO audio file can be played back as MP3 file. The system may not play back an Xvid file when the file has been combined from two or more Xvid files. * Mixed CD: This format records data on the first track and audio (AUDIO CD data) on the second and subsequent tracks of a session. masterpage:Right Notes on CD-R/-RW and DVD-R/-RW/+R/+RW In some cases, a CD-R/-RW and DVD-R/-RW/+R/+RW cannot be played back on this system due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. For more information, refer to the operating instructions of the recording device. Some playback functions may not work with some DVD+Rs/+RWs, even if they have been correctly finalized. In this case, view the disc by normal playback. Notes on discs This product is designed to play back discs that conform to the Compact Disc (CD) standard. DualDisc and some music discs encoded with copyright protection technologies do not conform to the CD standard. Therefore, these discs may not be compatible with this product. Note on multisession disc This system can play back continuous sessions on a disc when they are recorded in the same format as the first session. However, the playback is not guaranteed. Note on DVD VIDEO and VIDEO CD playback operations Some playback operations for a DVD VIDEO or VIDEO CD may be intentionally restricted by software producers. Therefore, some playback features may not be available. Be sure to read the operating instructions of the DVD VIDEO or VIDEO CD. 9GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\040PLA.fm] Notes on playable files Playback may take a longer time to start when: a DATA CD/DATA DVD/USB device is recorded with a complicated tree structure. the audio files or video files in another folder have just been played back. The system can play back a DATA CD/ DATA DVD or a USB device in the following conditions: up to a depth of 8 folders up to 300 folders up to 999 files in a disc up to 2,000 files in a USB device up to 650 files in a folder These numbers may vary depending on the file or folder configuration. Folders that have no audio files or video files are skipped. Files transferred by a device such as a computer may not be played back in the order in which they were transferred. The playback order may not be applicable depending on the software used for creating the audio file or video file. Compatibility with all MP3/WMA/ AAC/WAV/MPEG4/Xvid encoding/ writing software, recording devices, and recording media cannot be guaranteed. Depending on the Xvid file, the picture may be unclear or the sound may skip. masterpage:Left When a USB device is inserted, the system reads all the files on the USB device. If there are many folders or files on the USB device, it may take a long time to finish reading the USB device. Do not connect the system and the USB device through a USB hub. With some connected USB devices, there may be a delay before an operation is performed by this system. The playback order for the system may differ from the playback order of the connected USB device. Before using a USB device, make sure that no virus-ridden files are on the USB device. Websites for compatible devices Check the websites below for the latest information about compatible USB and BLUETOOTH devices. For customers in Latin America: <http://esupport.sony.com/LA> For customers in Europe and Russia: <http://www.sony.eu/support> For customers in Asia Pacific: <http://www.sony-asia.com/support> Notes about USB devices This system is not guaranteed to operate with all USB devices. Although there are a variety of complex functions for USB devices, the playable contents of USB devices connected to the system are music and video contents only. For details, refer to the operating instructions of the USB device. 10GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\040PLA.fm] masterpage:Right Guide to parts and controls Active Subwoofer ̙ ̘ ̚ ̛ ̜ ̗ ̖ ̝ ̕ ̞ ̔ ̟ ̠ ̡ ̤ ̣ ̢ Note The and VOLUME + buttons have a tactile dot. Use the tactile dot as a reference when operating the system. 11GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\040PLA.fm] (power) Turns on the system, or sets it to standby mode. (play) Starts playback. Hold down on the subwoofer for more than 2 seconds, the builtin sound demonstration will be played back on the system. Press to stop the demonstration. (stop) Stops playback. Press twice to cancel resume playback. BLUETOOTH Press to select BLUETOOTH function. PAIRING Hold down to activate BLUETOOTH pairing during BLUETOOTH function. BLUETOOTH indicator (page 39) FUNCTION Selects a function. REC TO USB Transfers music to the USB device which is connected to the (USB) port. ENTER Enters the settings. (USB) (REC/PLAY) port Connects a USB device. SOUND FIELD (page 46) masterpage:Left VOCAL FADER (page 51) MIC ECHO (page 51) MIC LEVEL (page 51) Turn MIC LEVEL clockwise or anticlockwise to adjust the microphone volume. +/– (select folder) Selects a folder on a data disc or a USB device. / (go backward/go forward) (page 26, 29, 41) TUNING+/– (page 38) (open/close) Inserts or ejects a disc. (N-Mark) (page 42) GESTURE CONTROL (page 44, 55) GESTURE ON/OFF (page 44, 55) Turns the Gesture Control on or off. PLAYBACK, DJ, SAMPLER, LIGHT (page 45, 46) PLAYBACK, DJ, SAMPLER, LIGHT indicators (page 45, 46) VOLUME +/– Adjusts the volume. Disc tray Remote control sensor MIC1, MIC2 jack Connects the microphone(s). FOOTBALL (page 46) PARTY LIGHT (page 52) PARTY CHAIN (page 50, 51, 61) MEGA BASS (page 46) Display panel FIESTA (page 46) Selects fiesta sound effect. FIESTA indicator (page 46) 12GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\040PLA.fm] Remote control masterpage:Right REPEAT/FM MODE (page 30, 38) SOUND FIELD buttons: MUSIC, VIDEO, FOOTBALL (page 46) Numeric buttons Selects a track, chapter or file. Tunes or presets a radio station. Enters a password. SUBTITLE (page 28) AUDIO (page 28, 31) ANGLE (page 28) SETUP (page 25, 30, 32, 61) MEDIA MODE (page 26, 37) CLEAR (page 28) VOCAL FADER (page 51) MIC ECHO (page 51) SCORE (page 52) +/– (select folder) Selects a folder on a data disc or a USB device. KEY CONTROL / (page 52) Notes The numeric button 2/AUDIO, + and buttons have a tactile dot. Use the tactile dot as a reference when operating the system. To use the button printed in pink, hold down SHIFT (), then press the button. (power) Turns on the system, or sets it to standby mode. DVD TOP MENU Displays the DVD title on the TV screen. DVD/TUNER MENU (page 27, 28, 39) RETURN (page 27) OPTIONS Enters or exits the options menu. / / / Selects the menu items. DISPLAY (page 25, 31, 38, 40) DISPLAY (page 31) SLEEP (page 52) PARTY LIGHT (page 52) LIGHT MODE (page 52) PLAY MODE (page 29, 36) Enters the settings. MEGA BASS (page 46) FUNCTION +/– Selects a function. SEARCH (page 26, 27) 13GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] SHIFT Hold down to activate the buttons printed in pink. +/– Adjusts the volume. / (rewind/fast forward) (page 27, 41) masterpage:Left Getting Started Installing the system The illustrations below are examples of how to install the system. Attaching the supplied speaker stands (Table Top Style) (page 16) and installing the speaker units vertically on either side of a TV on a rack Combining speaker units (Sound Bar Style) (page 16) and installing the combined unit in a TV rack / (slow backward/slow forward) (page 27) Watches the Slow-motion Play. TUNING+/– (page 38) (play) Starts playback. / (go backward/go forward) (page 26, 29, 41) PRESET+/– (page 39) (pause) (page 26, 27, 41) (stop) Stops playback. Press twice to cancel resume playback. Stops the built-in sound demonstration. 14GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] Installing the speaker units on a wall (page 17) To install the speaker units horizontally masterpage:Right To install the speaker units vertically Getting Started Do not place the speaker system and the subwoofer in a metal cabinet. Do not place an object such as an aquarium between the speaker system and the subwoofer. Place the subwoofer close to the speaker system in a same room. When the speaker system is placed in front of a TV, be sure not to obstruct the TV screen or the TV remote control sensor. If the TV remote control sensor is obstructed by the speaker system, the remote control may not be able to control the TV. Place the subwoofer at least 8 cm from the wall to avoid damaging the protruding AC power cord (mains lead). 8 cm Installing the speaker units on the rod of the subwoofer (Line Array Style) (page 18) Notes Do not let children or infants be near the system. Do not install the system on a slope. Take following precautions when installing the speaker system and the subwoofer. Do not block the ventilation holes on the rear panel of the subwoofer. 15GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] Attaching the speaker stands (Table Top Style) 1 Align the protruded part of the speaker unit with the recessed area of the speaker stand. Left speaker unit Right speaker unit masterpage:Left Combining the speaker units (Sound Bar Style) 1 Attach the supplied speaker pads on the speaker units to prevent them from slipping. Left speaker unit Right speaker unit 2 Secure the speaker unit and the speaker stand. Fasten the screws (supplied) from the bottom of the speaker stand. 2 Align the speaker units. Left speaker unit Right speaker unit 16GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] Installing the speaker units on a wall Notes masterpage:Right 2 Drive the screws to the wall. The screws should protrude 6 mm to 7 mm from the wall. To install the speaker units horizontally Use screws (not supplied) that are 1 277 mm Getting Started suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a wall stud. Install the speaker system on a vertical and flat reinforced area of the wall. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation. Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength, improper screw installation or natural calamity, etc. 6 mm to 7 mm To install the speaker units vertically Prepare screws (not supplied) that are suitable for the holes on the back of the speaker system. 277 mm 4 mm More than 25 mm Hole on the back of the speaker system 5 mm 5 mm 10 mm 6 mm to 7 mm 3 Hang the speaker system onto the screws. Align the holes on the back of the speaker system to the screws, then hang the speaker system onto the screws. To install the speaker units horizontally 17GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] To install the speaker units vertically Attaching the speaker units onto the mounting rod of the subwoofer (Line Array Style) Note Remove USB device from the subwoofer beforehand to prevent them from being damaged by accidentally dropping the speaker units. 1 masterpage:Left Lock the clip. Proceed to step 2 if you want to install the speaker units at this height (approx. 1.3 m). We recomment you to proceed to step 1- to install the speaker units at maximum height (approx. 1.6 m). Unlock the stopper, then press the release button and pull up the rod until the release button clicks into place. Pull up the mounting rod of the subwoofer. Unlock the clip, then press the release button and pull up the rod until the release button clicks into place. Stopper Release button Lock the stopper. Clip Release button Notes Adjust the rod before attaching the speaker units. Do not adjust the rod with the speaker units installed as the speaker units may drop. 18GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] Be careful not to get your hand caught when putting the rod back into the storing position. 2 Mount the speaker units to the attachments. Open the lock lever. masterpage:Right Note Be sure to close the lock lever when detaching the speaker units as it may generate noise during playback. 3 Fasten the speaker cables on the mounting rod. Thread the speaker cable into the cable clip and plug into the clip hole on the mounting rod. Getting Started Align the bracket of the speaker unit with the bracket of the speaker attachment, and then slide down to attach the speaker unit. Right speaker unit Left speaker unit Clip hole Cable clip Repeat step above to install all the cable clips. Clip hole Close the lock lever. 4 Connect the speaker connectors and LED speaker connectors to the respective terminals. For details, see illustration in page 21. 19GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] 5 Fold the speaker cables and masterpage:Left Notes The caster wheels can be used only on fasten to the cable tie. Cable tie flat surfaces. Lift the subwoofer by two persons on uneven surfaces. Correct hand placement while carrying the subwoofer is very important to avoid personal injury and/or property damage. Exercise extreme caution when carrying Carrying the system The subwoofer has caster wheels and a flip handle on the rod so that you can roll it easily. Normally, carrying the subwoofer by this method is recommended on flat surfaces. Before carrying the subwoofer, disconnect all the cables and speaker units. the subwoofer on a slope. Do not lift the subwoofer by the flip handle on the rod. Do not carry the subwoofer with the speaker units installed (Line Array Style) as the speaker units may drop. Do not carry the subwoofer with a person, luggage, etc. on it. Do not let children or infants be near when carrying the system. This system is not drip-proof or waterproof. Do not carry the system on a wet place. 20GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] masterpage:Right Hooking up the system securely Red Getting Started White To wall outlet * A small space is left between the plug and the subwoofer even when the AC power cord (mains lead) is inserted firmly. The cord is supposed be connected this way. This is not a malfunction. 21GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] Speakers LED SPEAKER L/R terminals Connect the LED speaker connector of the speaker to this terminal. The lighting on the subwoofer and speakers will react according to the music source (page 52). SPEAKERS L/R terminals Connect the speaker connector of the speaker to this terminal. Notes Be sure to use only the supplied speaker. When connecting speaker cables, insert the connector straight into the terminals. FM ANTENNA Find a location and an orientation that provide good reception when you set up the antenna. Keep the antenna away from the speaker cables, the AC power cord (mains lead) and the USB cable to avoid picking up noise. Extend the FM lead antenna horizontally masterpage:Left AUDIO/PARTY CHAIN IN (TV) L/R jacks Connect to the audio output jacks of a TV or an audio/video equipment. The sound is output through this system (page 23). Connect to another audio system to enjoy the Party Chain function (page 49). HDMI OUT (TV) jack Use an HDMI cable (not supplied) to connect to the HDMI IN jack of a TV (page 23). VIDEO OUT jack Use a video cable (not supplied) to connect to the video input jack of a TV or projector (page 23). Note Do not connect this system to the TV through the video deck. Power Connect the AC power cord (mains lead) (supplied) to the system, then plug it into a wall outlet. The demonstration appears in the display panel. Press to turn on the system and the demonstration automatically ends. Audio Use an audio cable (not supplied) to make either connection as follows: AUDIO/PARTY CHAIN OUT L/R jacks Connect to the audio input jacks of an optional equipment. Connect to another audio system to enjoy the Party Chain function (page 49). 22GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] masterpage:Right Connecting the TV Before connecting cables, be sure to disconnect the AC power cord (mains lead). To watch video Select the connection methods according to the jacks on your TV. High quality or Video cable (not supplied) Getting Started HDMI cable1) (not supplied) Standard quality Recommended connection Alternative connection 1) High Speed HDMI Cable with Ethernet 2) You can listen to TV sound via the system if you connect the system to the TV’s HDMI IN (ARC) jack. The Audio Return Channel (ARC) function enables the TV to output sound through the system with an HDMI connection, without performing an audio connection (connection below). To set the ARC function on this system, see [AUDIO RETURN CHANNEL] (page 35). To check the compatibility of your TV’s ARC function, refer to the operating instructions supplied with your TV. To listen to TV sound via the system If you do not connect the system to the TV’s HDMI IN (ARC) jack, make this connection. Audio cable (not supplied) AUDIO OUT To listen to TV sound, press FUNCTION +/– repeatedly to select “TV”. 23GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] masterpage:Left Notes You can also enjoy the sound of external equipment (DVD players, etc.) via the system by connecting to the AUDIO IN (TV) jack as connection above. For details, refer to the operating instructions of your equipment. If the audio output level from the system is low when connecting the external equipment, try adjusting the audio output settings on the connected equipment. It may improve the audio output level. For details, refer to the operating instructions of your equipment. If “CODE 01” and “SGNL ERR” appear in the display panel of the subwoofer When the audio input signals to the system are other than 2-channel Linear PCM signals, the message “CODE 01” and “SGNL ERR” (indicates that the input audio signals are unsupported) appear in the display panel of the subwoofer. In this case, select the proper audio output mode on the TV in order to output 2-channel Linear PCM audio signals. For details, refer to the operating instructions of your TV. Inserting batteries Insert the two supplied R03 (size AAA) batteries by matching the polarities as shown below. To operate the system using the remote control Point the remote control at the subwoofer’s remote control sensor. Notes Do not mix an old battery with a new one or mix different types of batteries. If you do not use the remote control for a long period of time, remove the batteries to avoid damage from battery leakage and corrosion. 24GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\050CON.fm] Performing QUICK setup Before using the system, you can make the minimum basic adjustments in QUICK setup. 1 Turn on your TV and select the input according to the connection. select “DVD/CD” or “USB” without inserting a disc or connecting a USB device. The guide message [Press ENTER to run QUICK SETUP.] appears at the bottom of the TV screen. 4 Press . [LANGUAGE SETUP] appears on the TV screen. Displayed items may vary depending on country or region. LANGUAGE SETUP OSD : MENU : AUDIO: SUBTITLE: ENGLISH ENGLISH CHINESE 1 CHINESE 2 THAI 5 Press / repeatedly to select a language, then press . [VIDEO SETUP] appears on the TV screen. 6 Press / repeatedly to select the setting that matches your TV type, then press . After [QUICK SETUP is complete.] appears on the TV screen, the system is ready for playback. To change the setting manually See “Using the Setup Menu” (page 32). To quit QUICK setup Note The guide message appears when you turn on the system for the first time or after performing “RESET” (page 61). Changing the color system (Except for Latin American, European, and Russian models) Set the color system to PAL or NTSC depending on the color system of your TV. Each time you perform the procedure below, the color system changes as follows: NTSC PAL Getting Started 2 Press to turn on the system. 3 Press FUNCTION +/– repeatedly to masterpage:Right Use the buttons on the subwoofer to perform this operation. 1 Press to turn on the system. 2 Press FUNCTION repeatedly to select “DVD/CD”. 3 Hold down MIC ECHO and ENTER for more than 3 seconds. “NTSC” or “PAL” appears in the display panel. Changing the display mode Press DISPLAY repeatedly when the system is turned off. Demonstration The demonstration is turned on. No display (Power Saving Mode) The display is turned off to conserve power. The Sleep Timer continues to operate. Press SETUP. 25GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] 4 Press to start playback. Disc/USB Playback Basic playback 1 Press FUNCTION +/– repeatedly to select “DVD/CD” or “USB”. 2 For DVD/CD function: Press on the subwoofer to open the disc tray and load a disc with the label facing up. When you play back an 8 cm disc such as a CD single, place it on the inner circle of the tray Press on the subwoofer again to close the disc tray. Do not forcibly push the disc tray to close it as this may cause a malfunction. For USB function: Connect a USB device to the port. masterpage:Left (USB) To Press Stop playback Pause playback Resume playback or return to normal playback Cancel the resume twice point Select a track, file, or during chapter or scene playback. Or, hold down SHIFT, then press the numeric buttons, and then press . (Operation might be prohibited by disc or USB device) To use the Gesture Control during playback See page 45. To play from a specific audio or video file 1 Press MEDIA MODE repeatedly to select [MUSIC] or [VIDEO]. 2 Press SEARCH to display the Folder List. 3 Press / repeatedly to select the folder you want. Notes You can use your iPhone/iPod with this system via BLUETOOTH connection only. You can use a USB adaptor (not supplied) to connect the USB device to the subwoofer if the USB device cannot be plugged into the (USB) port. 3( only) Press MEDIA MODE repeatedly to select the media ([MUSIC]/ [VIDEO]) you want. 26GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] 4 Press to display the File List. masterpage:Right Searching a specific track Hold down SHIFT, then press the numeric buttons to select the track you want to play back, then press . 5 Press / repeatedly to select the file you want, then press . 1 Press SEARCH to display the Track List. 2 Press / repeatedly to select the track you want to play back, then press . Searching a specific title/ chapter/scene/track/index Depending on the type of disc or file, the function may not work. To Press View DVD menu DVD/TUNER MENU View Folder List or SEARCH. Press the File List button again to turn off the Folder List or File List. 1 or during playback. Each time you press the button, the playback speed changes. Watch frame by frame (Slowmotion Play) , then press or . Each time you press or , the playback speed changes. Press SEARCH repeatedly during playback to select the search mode. 2 Hold down SHIFT, then press the numeric buttons to enter the title, chapter, scene, track, or index number you want, then press . Playback starts. Return to Folder RETURN List when in File List Locate a point quickly in fast forward or fast reverse (Lock Search) Disc/USB Playback Other playback operations To search using the SEARCH button Notes For VIDEO CD with PBC playback, press SEARCH to search the scene. For VIDEO CD without PBC playback, press SEARCH to search the track and index. To search using the time code 1 Press SEARCH repeatedly during playback to select the time search mode. 27GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] 2 Hold down SHIFT, then press the numeric buttons to enter the time code, then press . Example: To find a scene at 2 hours, 10 minutes, and 20 seconds, hold down SHIFT, then press 2, 1, 0, 2, 0 ([2:10:20]). Press CLEAR to cancel the number. To search using the DVD menu 1 2 Press DVD/TUNER MENU. Press / / / or hold down SHIFT, then press the numeric buttons to select the title or item you want to play back, then press . Changing the angles masterpage:Left DVD VIDEO You can toggle audio format or language when the source contains multiple audio formats or multilingual audio. When 4 digits are displayed, they indicate a language code. See “Language code list” (page 67) to confirm which language the code represents. When the same language is displayed two or more times, the DVD VIDEO is recorded in multiple audio formats. VIDEO CD/AUDIO CD/DATA CD/ DATA DVD (MP3 file) or USB device (audio file) You can change the sound track. [STEREO]: The stereo sound. [1/L]/[2/R]: The monaural sound of the left or right channel. SUPER VIDEO CD Press ANGLE repeatedly during playback to select the angle you want. Displaying the subtitles Press SUBTITLE repeatedly during playback to select the subtitle language you want or turn off the subtitle. Changing the language/ sound Press AUDIO repeatedly during playback to select the audio format or mode you want. [1:STEREO]: The stereo sound of audio track 1. [1:1/L]/[1:2/R]: The monaural sound of the left or right channel of audio track 1. [2:STEREO]: The stereo sound of audio track 2. [2:1/L]/[2:2/R]: The monaural sound of the left or right channel of audio track 2. Playing a VIDEO CD with PBC functions You can use the PBC (Playback Control) menu to enjoy the VIDEO CD’s interactive software. 1 Press to play a VIDEO CD in PBC. The PBC menu appears on the TV screen. 28GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] 2 Hold down SHIFT, then press the numeric buttons to select the item number you want, then press . masterpage:Right Using play mode Playing in original order (Normal Play) 3 Continue playback according to the instructions on the menu. Note PBC playback is canceled when Repeat Play is activated. To cancel PBC playback When playback is stopped, press PLAY MODE repeatedly. Press or , or hold down SHIFT, then press the numeric buttons to select a track when playback is stopped. 2 Press or . Playback starts from the selected track. When playing a USB device [ONE USB DEVICE]: plays a USB device. [FOLDER]: plays all compatible files in the folder on a USB device. To return to PBC playback * Cannot be selected for AUDIO CD. Disc/USB Playback When playing a disc [DISC]: plays a disc. [FOLDER]*: plays all compatible files in the folder on the disc. 1 Press twice, then press . Playing in random order (Shuffle Play) Multi-disc resume play This system can store playback resume points for up to 6 discs and resumes playback when you insert the same disc again. If you store a playback resume point for the 7th disc, the resume point for the first disc will be deleted. To activate this function, set [MULTIDISC RESUME] in [SYSTEM SETUP] to [ON] (page 34). Note To play back from the beginning of the disc, press twice, then press . When playback is stopped, press PLAY MODE repeatedly. When playing a disc [DISC (SHUFFLE)]: shuffles all audio files on a disc. [FOLDER (SHUFFLE)]*: shuffles all audio files in the folder on the disc. * Cannot be selected for AUDIO CD. When playing a USB device [ONE USB DEVICE (SHUFFLE)]: shuffles all audio files on a USB device. [FOLDER (SHUFFLE)]: shuffles all compatible files in the folder on the USB device. Notes Shuffle Play cannot be performed for video files. 29GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] Shuffle Play is canceled when you: turn off the system. open the disc tray. perform Synchronized Transfer. change MEDIA MODE. Shuffle Play may be canceled when you select a folder or a track to play back. Playing repeatedly (Repeat Play) Press REPEAT repeatedly. Depending on the type of disc or file, some settings may not be available. [OFF]: does not play back repeatedly. [ALL]: repeats all tracks or files in the selected play mode. [DISC]: repeats all contents (DVD VIDEO and VIDEO CD only). [TITLE]: repeats the current title (DVD VIDEO only). [CHAPTER]: repeats the current chapter (DVD VIDEO only). [TRACK]: repeats the current track. [FILE]: repeats the current video file. To cancel Repeat Play Press REPEAT repeatedly to select [OFF]. Notes “ ” lights up in the display panel when Repeat Play is set to [ALL] or [DISC]. “ ” lights up in the display panel when Repeat Play is set to [TITLE], [CHAPTER], [TRACK] or [FILE]. You cannot perform Repeat Play with VIDEO CD during PBC playback. Depending on the DVD VIDEO, you cannot perform Repeat Play. Repeat Play is canceled when you: open the disc tray. turn off the system (DVD VIDEO and VIDEO CD only). change the function (DVD VIDEO and VIDEO CD only). perform Synchronized Transfer. change MEDIA MODE. masterpage:Left Restricting playback of the disc (Parental Control) You can restrict playback of DVD VIDEOs according to a predetermined level. Scenes may be skipped or replaced with different scenes. 1 When playback is stopped, press SETUP. 2 Press / repeatedly to select [SYSTEM SETUP], then press . 3 Press / repeatedly to select [PARENTAL CONTROL], then press . 4 Enter or re-enter your 4-digit password using the numeric buttons, then press . 5 Press / repeatedly to select [STANDARD], then press . 6 Press / repeatedly to select a geographic area as the playback limitation level, then press . The area is selected. When you select [OTHERS ], enter the area code for the geographic area you want according to the “Parental Control area code list” on page 68 by using the numeric buttons. 7 Press / repeatedly to select [LEVEL], then press . 8 Press / repeatedly to select the level you want, then press . The lower the value, the stricter the limitation. 30GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] masterpage:Right To turn off the PARENTAL CONTROL function Playback information Playing time, remaining time Set [LEVEL] to [OFF] in step 8. Bit rate To play back a disc for which PARENTAL CONTROL is set File type 1 Title1)/track/file name2) Load the disc and press . The display for entering your password appears on the TV screen. 2 Album1)/folder name2)/chapter/ index number Artist name1)2) Appears when playing an audio file. 1) If you forget your password Remove the disc and repeat steps 1 to 3 of “Restricting playback of the disc” (page 30). Enter a password “199703” using the numeric buttons, then press . Follow the on-screen instructions and enter a new 4-digit password. Then, reload the disc and press . You need to enter your new password again. Viewing information of a disc and USB device Information on the TV screen Hold down SHIFT, then press DISPLAY repeatedly during playback. If an audio file has an ID3 tag, the system will display an album name/title name/artist name from the ID3 tag information. The system can support ID3 ver 1.0/1.1/2.2/2.3. 2) If the file or folder contains characters which cannot be displayed, those characters will be displayed as “_”. Notes Disc/USB Playback Enter your 4-digit password using the numeric buttons, then press . The system starts playback. Playback status Depending on the source being played, some information may not be displayed. some characters cannot be displayed. Depending on the play mode, the information displayed may be different. Displaying the audio information (DVD VIDEO and video files only) Press AUDIO repeatedly during playback. Information in the display panel Press DISPLAY repeatedly when the system is on. You can view the information as follows: playing time, remaining time of track, title, chapter scene number file name, folder name title, artist and album information 31GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] Notes masterpage:Left Setting the language – [LANGUAGE SETUP] The disc name or track name may not be displayed depending on the text. Playing time of MP3 files and video files may not be displayed correctly. The elapsed playing time of an audio file encoded using a VBR (variable bit rate) is not displayed correctly. [OSD] Selects the language of the on-screen display. [MENU] Using the Setup Menu You can make various adjustments to items such as picture and sound. Displayed items vary depending on the country or region. Note Playback settings stored in the disc take priority over the Setup Menu settings. Therefore, some of the Setup Menu settings may not be performed. 1 Press FUNCTION +/– repeatedly to select “DVD/CD” or “USB”. 2 When playback is stopped, press SETUP. The Setup Menu appears on the TV screen. 3 Press / repeatedly to select [LANGUAGE SETUP], [VIDEO SETUP], [AUDIO SETUP], [SYSTEM SETUP] or [HDMI SETUP], then press . Selects the language for the DVD menu. [AUDIO] Switches the language of the sound track. When you select [ORIGINAL], the language given priority in the disc is selected. [SUBTITLE] Switches the language of the subtitle recorded on the DVD VIDEO. When you select [AUDIO FOLLOW], the language for the subtitles changes according to the language you selected for the sound track. Note If you select [OTHERS ] in [MENU], [AUDIO], and [SUBTITLE], enter a language code from the “Language code list” (page 67) using the numeric buttons. 4 Press / repeatedly to select the item you want, then press . 5 Press / repeatedly to select the setting you want, then press . The setting is selected and setup is completed. To exit the menu Press SETUP. 32GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] Setting the TV screen – [VIDEO SETUP] [TV TYPE] masterpage:Right [NORMAL]: Changes the picture size to fit the screen size with the original picture aspect ratio. This setting displays black bands on the left and right side if you display a 4:3 screen picture. [16:9]: Selects this when you connect a wide-screen TV or a TV with a wide mode function. [4:3 LETTER BOX]: Selects this when you connect a 4:3 screen TV without a wide mode function. This setting displays a wide picture with black bands on the top and bottom. [4:3 PAN SCAN]: Selects this when you connect a 4:3 screen TV without a wide mode function. This setting displays a full-height picture on the entire screen, with trimmed sides. Selects the color system (PAL or NTSC). [AUTO]: Outputs the video signal according to the color system of the disc. Select this setting if your TV uses a DUAL system. [PAL]: Outputs the video signal in PAL. [NTSC]: Outputs the video signal in NTSC. For details, see “Changing the color system” (page 25). Disc/USB Playback [COLOR SYSTEM(VIDEO CD)] (Except for Latin American, European, and Russian models) [BLACK LEVEL] (For Latin American models only) Selects the black level (setup level) for the video signals output from the VIDEO OUT jack. [ON]: Sets the black level of the output signal to the standard level. [OFF]: Lowers the standard black level. Use this when the picture becomes too white. [4:3 OUTPUT] [PAUSE MODE] [FULL]: Selects this when you connect a TV with a wide mode function. Displays a 4:3 screen picture in 16:9 aspect ratio even on a wide-screen TV. [AUTO]: The picture, including subjects that move dynamically, is output with no jitter. Normally select this setting. [FRAME]: The picture, including subjects that do not move dynamically, is output in high resolution. 33GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] Setting the audio options – [AUDIO SETUP] [AUDIO DRC] (Dynamic Range Compression) Useful for watching movies at low volume late at night. [OFF]: Off. [STANDARD]: The dynamic range is compressed as intended by the recording engineer. [TRACK SELECTION] [OFF]: Off. [AUTO]: Gives priority to the sound track which contains the highest number of channels when you play back a DVD VIDEO on which multiple audio formats (PCM, MPEG, or Dolby Digital) are recorded. [A/V SYNC] (Video files only) [OFF]: Off. [ON]: Adjusts the delay between picture and sound. [DOWNMIX] Selects the audio output signal for playing a multi-channel audio. [NORMAL]: Outputs multi-channel audio into a 2-channel stereo signal. [DOLBY SURROUND]: Outputs multichannel audio into a 2-channel surround signal. masterpage:Left Setting the system – [SYSTEM SETUP] [SCREEN SAVER] Prevents damage on the TV. Press +/– to cancel the screen saver. [ON]: Turns on the screen saver function if you do not operate the system for about 15 minutes. [OFF]: Off. [BACKGROUND] Selects the background color or picture to be displayed on the TV screen. [JACKET PICTURE]: The jacket picture (still picture) that recorded on the disc appears in the background. [GRAPHICS]: A preset picture stored in the system appears in the background. [BLUE]: The background color is blue. [BLACK]: The background color is black. [PARENTAL CONTROL] Sets the playback restrictions. For details, see “Restricting playback of the disc” (page 30). [MULTI-DISC RESUME] [ON]: Stores the resume playback point in the memory for up to 6 discs. [OFF]: Only stores the resume playback point for the current disc in the system. [RESET] Returns SETUP settings to the default settings. For details, see “To return the SETUP settings to the default” (page 61). 34GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] Setting the HDMI options – [HDMI SETUP] 1) [STANDBY LINKED TO TV] This function is available when you set [CONTROL FOR HDMI] to [ON]. [AUTO]: If the input of the system is “TV”, the system turns off automatically when you turn off the TV. [ON]: The system turns off automatically when you turn off the TV regardless of the input. [OFF]: The system does not turn off when you turn off the TV. Disc/USB Playback [HDMI RESOLUTION] Selects the TV output resolution when the TV is connected via HDMI cable. [AUTO(1920×1080p)]1): Outputs video signals according to the resolution of the TV. [1920×1080i]/[1280×720p]/ [720×480p]2)/[720×480p/576p]3): Outputs video signals according to the selected resolution setting. masterpage:Right For Russian models, the default setting is [АВТО(1920×1080p)]. Latin American models only. other models. 2) For 3) For [YCBCR/RGB(HDMI)] [YCBCR]: Outputs YCBCR video signals. Set to [RGB] if the playback picture is distorted. [RGB]: Outputs RGB video signals. [AUDIO(HDMI)] [AUTO]: Outputs audio signals in original format from HDMI OUT (TV) jack. [PCM]: Outputs 2-channel Linear PCM signals from HDMI OUT (TV) jack. [CONTROL FOR HDMI] [ON]: The Control for HDMI function is enabled. You can operate mutually between system and TV connected with an HDMI cable. [OFF]: Off. [AUDIO RETURN CHANNEL] Set this function when the system is connected to a TV’s HDMI IN jack that is compatible with Audio Return Channel. This function is available when you set [CONTROL FOR HDMI] to [ON]. [ON]: You can listen to TV sound from the speakers of the system. [OFF]: Off. 35GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] USB Transfer Transferring music You can transfer music from a disc (AUDIO CD or MP3 disc only) to a USB device connected to the (USB) port. The audio format of files transferred by this system is MP3. Notes Do not remove the USB device during transfer or erase operations. Doing so may corrupt the data on the USB device or damage the USB device itself. MP3 files are transferred with the same bit rate as the original files. When transferring from AUDIO CD, you may select the bit rate before transferring. USB transfer and erase operations are prohibited when the disc tray is opened. Note on copyright-protected content The transferred music is limited to private use only. Use of the music beyond this limit requires permission of the copyright holders. masterpage:Left Transferring music from a disc You can transfer music to a USB device connected to (USB) port as follows: Synchronized Transfer: Transfer all supported music files from a disc to USB. REC1 Transfer: Transfer a single track or audio file during playback. Use the buttons on the subwoofer to perform this operation. 1 Connect a transferable USB device to the (USB) port. 2 Press FUNCTION repeatedly to select “DVD/CD”, then load a disc. If the system starts playback automatically, press twice to stop the playback. 3 Prepare the sound source. For Synchronized Transfer: When playback is stopped, press PLAY MODE on the remote control repeatedly to select the play mode you want. Note To select the bit rate You can select a higher bit rate to transfer music with better quality. 1 2 Press OPTIONS. 3 Press / repeatedly to select the bit rate you want, then press . 128 KBPS: encoded MP3 tracks have smaller file size and lower audio quality. 256 KBPS: encoded MP3 tracks have bigger file size but higher audio quality. To exit the options menu, press OPTIONS. Press / repeatedly to select “BIT RATE”, then press . If you start transferring in Shuffle Play or Repeat Play, the selected play mode changes to Normal Play automatically. For REC1 Transfer: Select the track or audio file you want to transfer, then start playback. 4 Press REC TO USB. “PUSH ENTER” appears in the display panel. 5 Press ENTER. The transfer starts when “DO NOT REMOVE” appears in the display panel. 36GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\060CDP.fm] When the transfer is completed The disc stops automatically (for Synchronized Transfer) or continues to play (for REC1 Transfer). To stop transfer Press . Notes on transfer While transferring, no sound is output. CD-TEXT information is not transferred Folder and file generation rules Maximum number of MP3 files that can be generated 298 folders 650 files in a folder 650 files in REC1-CD or REC1-MP3 folder. These numbers may vary depending on the file or folder configuration. When transferring onto a USB device, a “MUSIC” folder is created directly below “ROOT”. Folders and files are generated within this “MUSIC” folder according to the transferring method and source. Synchronized Transfer Source Folder name Audio files Same as the source File name AUDIO CD “CDDA0001”* “TRACK001”* REC1 Transfer Source Folder name File name Audio files “REC1-MP3” Same as the source AUDIO CD “REC1-CD” “TRACK001”* * Folder and file numbers are assigned serially thereafter. USB Transfer in the created MP3 files. The transfer stops automatically if: the USB device runs out of space during transfer. the number of audio files or folders on the USB device reaches the limit. If a folder or file that you are trying to transfer already exists on the USB device with the same name, a sequential number is added after the name without overwriting the original folder or file. You cannot perform the following operations during a transfer: Eject the disc. Select another track or file. Pause playback or find a point in the track or file. Change the function. When transferring music to a Walkman® using “Media Manager for WALKMAN”, be sure to transfer in MP3 format. When connecting a Walkman® to the system, be sure to connect after the display “Creating Library” or “Creating Database” on the Walkman® has disappeared. masterpage:Right Erasing audio files or folders on the USB device 1 Press FUNCTION +/– repeatedly to select “USB”. 2 Press MEDIA MODE repeatedly to select [MUSIC]. 3 When playback is stopped, press OPTIONS. 4 Press / repeatedly to select “ERASE”, then press . The Folder List is displayed on the TV screen. 5 Press / repeatedly to select a folder, then press . 37GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\070TUN.fm] 6 Press / repeatedly to select the audio file you want to erase, then press . Select [ALL TRACKS] to select all audio files in the folder. “FOLDER ERASE” or “TRACK ERASE” and “PUSH ENTER” appear in the display panel. To cancel, press . 7 Press . “COMPLETE” appears in the display panel. To exit the options menu, press OPTIONS. Notes A folder that contains non-MP3/WMA/ AAC/WAV format audio files or sub folders cannot be erased. You cannot erase audio files or folders when Shuffle Play has been selected. Set the play mode to Normal Play before erasing. Erase operation is prohibited when the disc tray is opened. masterpage:Left Tuner Listening to the radio 1 Press FUNCTION +/– repeatedly to select “TUNER FM”. 2 Select the radio station. For automatic tuning: Hold down TUNING+/– until the frequency indication changes and then release. Scanning stops automatically when a station is tuned in. “ST” (for FM stereo programs only) lights up in the display panel. If scanning does not stop, press to stop scanning. Then, perform manual tuning (below). For manual tuning: Press TUNING+/– repeatedly to tune to the station you want. Note When you tune to an FM station that provides RDS services, information such as the service name or station name is provided by broadcasts. You can check the RDS information by pressing DISPLAY repeatedly. Tip To reduce static noise on a weak FM stereo station, press FM MODE repeatedly until “ST” disappears from the display panel. You will lose the stereo effect, but reception will improve. 38GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\070TUN.fm] Presetting radio stations You can store up to 20 FM stations as your favorite stations. 1 Tune to the station you want. 2 Press DVD/TUNER MENU. 3 Press / repeatedly to select the preset number you want, then press . “COMPLETE” appears in the display panel. The station is stored. If another station is already assigned to the selected preset number, that station is replaced by the new one. masterpage:Right BLUETOOTH About the BLUETOOTH wireless technology BLUETOOTH wireless technology is a short-range wireless technology that enables wireless data communication between digital devices. BLUETOOTH wireless technology operates within a range of about 10 meters. Supported BLUETOOTH version, profiles and codecs For details, see “BLUETOOTH section” (page 66). Compatible BLUETOOTH devices Press PRESET+/– repeatedly to select the preset number you want. You can also hold down SHIFT, then press the numeric buttons, and then press to select a preset station. For details, see “Websites for compatible devices” (page 10). About the BLUETOOTH indicator Tuner/BLUETOOTH To tune to a preset station The BLUETOOTH indicator on the subwoofer lights up or flashes in blue to show the BLUETOOTH status. System status Indicator status BLUETOOTH standby Flashes slowly BLUETOOTH pairing Flashes quickly BLUETOOTH connection is established Lights up 39GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\070TUN.fm] Note Pairing this system with a BLUETOOTH device Pairing is an operation where BLUETOOTH devices register with each other beforehand. Once a pairing operation is performed, it does not need to be performed again. 1 masterpage:Left If passkey is required on the BLUETOOTH device, enter “0000”. “Passkey” may be called “Passcode”, “PIN code”, “PIN number”, or “Password”. 6 Perform the BLUETOOTH connection on the BLUETOOTH device. The BLUETOOTH device name appears in the display panel. Depending on the BLUETOOTH device, connection may start automatically after pairing is completed. You can check the BLUETOOTH device address by pressing DISPLAY repeatedly. Place the BLUETOOTH device within 1 meter from the system. 2 Press BLUETOOTH on the subwoofer to select BLUETOOTH function. “BT AUDIO” appears in the display panel. Notes Notes When there is no pairing information You can pair up to 9 BLUETOOTH on the system, the system enters the pairing mode automatically and “PAIRING” flashes in the display panel. Proceed to step 4. If the system is connected to a BLUETOOTH device, press BLUETOOTH on the subwoofer to disconnect the BLUETOOTH device. devices. If the 10th BLUETOOTH device is paired, the oldest paired device will be deleted. If you want to pair with another BLUETOOTH device, repeat steps 1 to 6. To cancel pairing operation 3 Hold down Hold down PAIRING on the subwoofer for 2 seconds or more until “BT AUDIO” appears in the display panel. 4 Perform the pairing procedure on To delete pairing information PAIRING on the subwoofer for 2 seconds or more. “PAIRING” flashes in the display panel. the BLUETOOTH device. For details, refer to the operating instructions of your BLUETOOTH device. 5 Select “MHC-GT4D” on the device’s display. Perform this step within 5 minutes, otherwise pairing will be canceled. In this case, repeat from step 1. Use the buttons on the subwoofer to perform this operation. 1 Press BLUETOOTH to select BLUETOOTH function. “BT AUDIO” appears in the display panel. If the system is connected to a BLUETOOTH device, the BLUETOOTH device name appears in the display panel. Press BLUETOOTH to disconnect the BLUETOOTH device. 40GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\070TUN.fm] 2 Hold down ENTER and – for about 3 seconds. “BT HIST CLEAR” appears in the display panel and all the pairing information is erased. Playing music from a BLUETOOTH device 1 Press BLUETOOTH on the subwoofer to select BLUETOOTH function. “BT AUDIO” appears in the display panel. 2 Establish connection with the BLUETOOTH device. Press BLUETOOTH on the subwoofer to connect to the last connected BLUETOOTH device. Perform the BLUETOOTH connection from the BLUETOOTH device if the device is not connected. Once the connection is established, the BLUETOOTH device name appears in the display panel. 3 Press to start playback. Depending on the BLUETOOTH device, you may have to press twice. you may need to start playing an audio source on the BLUETOOTH device. 4 Adjust the volume. Adjust the volume of the BLUETOOTH device first, if the volume level is still too low, adjust the volume level on the system. Notes When the system is not connected to any BLUETOOTH device, the system will connect to the last connected BLUETOOTH device automatically when you press BLUETOOTH on the subwoofer or . If you try to connect another BLUETOOTH device to the system, the current connected BLUETOOTH device will be disconnected. To use the Gesture Control during playback BLUETOOTH You can operate a BLUETOOTH device by connecting the system and the BLUETOOTH device using AVRCP. Once the system and BLUETOOTH device is connected, you can control playback by pressing , , , / and /. Check the following before playing music: The BLUETOOTH function of the BLUETOOTH device is turned on. The pairing has been completed (page 40). masterpage:Right See page 45. To disconnect the BLUETOOTH device Press BLUETOOTH on the subwoofer. “BT AUDIO” appears in the display panel. Depending on the BLUETOOTH device, the BLUETOOTH connection may be canceled automatically when you stop playback. 41GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\070TUN.fm] One Touch BLUETOOTH Connection by NFC NFC (Near Field Communication) is a technology enabling short-range wireless communication between various devices, such as smartphones and IC tags. When you touch the system with an NFC-compatible smartphone, the system automatically: turns on in BLUETOOTH function. completes the pairing and BLUETOOTH connection. Compatible smartphones Smartphones with a built-in NFC function (OS: Android 2.3.3 or later, excluding Android 3.x) Notes 1 masterpage:Left Touch the smartphone to the N-Mark on the subwoofer until the smartphone vibrates. Complete the connection by following the instructions displayed on the smartphone. When the BLUETOOTH connection is established, the BLUETOOTH device name appears in the display panel. 2 Start playback of an audio source on the smartphone. For details, refer to the operating instructions of your BLUETOOTH device. The system only can recognizes and connects to one NFC-compatible smartphone at a time. If you try to connect another NFC-compatible smartphone to the system, the current connected NFC-compatible smartphone will be disconnected. Depending on your NFC-compatible smartphone, you may need to perform the following items on your NFCcompatible smartphone in advance. Turn on the NFC function. For details, refer to the operating instructions of the NFC-compatible smartphone. If your NFC-compatible smartphone is having an older OS version than Android 4.1.x, download and start the “NFC Easy Connect” application. “NFC Easy Connect” is a free application for Android smartphone that can be obtained from Google Play. (The application may not be available in some countries/regions.) Tip If pairing and the BLUETOOTH connection fail, do the following. Remove the case from the smartphone if using a commercially available smartphone case. Touch the smartphone to the N-Mark on the subwoofer again. Relaunch “NFC Easy Connect” application. To disconnect the smartphone Touch the smartphone to the N-Mark on the subwoofer again. 42GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\070TUN.fm] Setting the BLUETOOTH audio codecs You can receive data in AAC, LDAC or SBC codec format from a BLUETOOTH device. 1 Press OPTIONS. 2 Press / repeatedly to select “BT CODEC”, then press . 3 Press / repeatedly to select the setting. AUTO: Enable reception in AAC or LDAC codec format. SBC: Receive in SBC codec format. To exit the options menu, press OPTIONS. You can enjoy high quality sound if the AAC or LDAC is selected. In case you cannot listen to AAC or LDAC sound from your device or the sound is interrupted, select “SBC”. If you change this setting when the system is connected to a BLUETOOTH device, the BLUETOOTH device will be disconnected. To connect to the BLUETOOTH device, perform the BLUETOOTH connection again. Tip LDAC is an audio coding technology developed by Sony that enables the transmission of High-Resolution (Hi-Res) Audio content, even over a BLUETOOTH connection. Unlike other BLUETOOTH compatible coding technologies such as SBC, it operates without any downconversion of the Hi-Res Audio content*, and allows approximately three times more data** than those other technologies to be transmitted over a BLUETOOTH wireless network with unprecedented sound quality, by means of efficient coding and optimized packetization. ** In comparison with SBC (Subband Coding) when the bitrate of 990 kbps (96/48 kHz) or 909 kbps (88.2/44.1 kHz) is selected. Setting the BLUETOOTH standby mode The BLUETOOTH standby mode enables the system to turn on automatically when you establish the BLUETOOTH connection from a BLUETOOTH device. 1 Press OPTIONS. 2 Press / repeatedly to select “BT STBY”, then press . 3 Press / repeatedly to select the setting. ON: The system turns on automatically when you establish a BLUETOOTH connection from a BLUETOOTH device. OFF: Turns off this function. To exit the options menu, press OPTIONS. BLUETOOTH Notes masterpage:Right Setting the BLUETOOTH signal You can connect to the system from a paired BLUETOOTH device in all functions when BLUETOOTH signal is set to on. The BLUETOOTH signal is turned on by default. Use the buttons on the subwoofer to perform this operation. Hold down ENTER and + for about 3 seconds. “BT ON” or “BT OFF” appears in the display panel. * Excluding DSD format contents. 43GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] Notes You cannot perform the following operations when BLUETOOTH signal is set to off: Pairing and/or connecting with BLUETOOTH device Erasing the pairing information Using “SongPal” via BLUETOOTH Change the BLUETOOTH audio codecs If you touch the system with an NFCcompatible smartphone or set the BLUETOOTH standby mode to on, the BLUETOOTH signals will set to on automatically. masterpage:Left Gesture Control Enjoying the Gesture Control You can control the operations for PLAYBACK, DJ, SAMPLER and LIGHT mode by swiping your hand over GESTURE CONTROL on the subwoofer. GESTURE CONTROL Using “SongPal” via BLUETOOTH About App Note A dedicated App for this model is available on both Google Play and App Store. Search for “SongPal” or scan the QR code below then download the free App to find out more about the convenient features. Make sure your hand does not touch GESTURE CONTROL when you perform the swiping motion. Swipe your hand over GESTURE CONTROL in 6 directions as follows. Swiping motion Swipe in this direction Right to left Left to right Bottom to top Top to bottom BLUETOOTH technology works with iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone 5c, iPhone 5, iPhone 4s, iPod touch (6th generation), iPod touch (5th generation). Note If “SongPal” application does not work properly, disconnect and connect the BLUETOOTH device by pressing BLUETOOTH on the subwoofer (page 41). Clockwise Anticlockwise To activate the Gesture Control Press GESTURE ON/OFF. The GESTURE CONTROL lights up. To deactivate the Gesture Control Press GESTURE ON/OFF. The GESTURE CONTROL lights off. 44GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] Using the Gesture Control during playback You can use the Gesture Control to control basic playback when playing music from a disc, USB device or BLUETOOTH device. Use the buttons and GESTURE CONTROL on the subwoofer to perform this operation. 1 Press GESTURE ON/OFF. The GESTURE CONTROL lights up. 2 Press PLAYBACK. The PLAYBACK indicator lights up. 3 Swipe your hand over GESTURE CONTROL. To Swipe in this direction Go backward Play Stop Increase volume Reduce volume 3 Swipe your hand over GESTURE CONTROL. For DJ mode: To Swipe in this direction Select FLANGER1) Select ISOLATOR2) Select WAH3) Select PAN4) Increase the level of the selected effect Reduce the level of the selected effect 1) Creates a deep flanging effect that is similar to the roar of a jet plane. 2) Isolates a specific frequency band by adjusting the other frequency bands. For example, when you want to focus on vocals. 3) Create a special effect of “Wah-wah” sound by moving the frequency of a filter up and down automatically. 4) Create a feeling that the sound is moving around the speakers between left and right channels. For SAMPLER mode: Creating a party atmosphere To (DJ EFFECT) Output “Let’s Go!” Use the buttons and GESTURE CONTROL on the subwoofer to perform this operation. 1 Press GESTURE ON/OFF. The GESTURE CONTROL lights up. 2 Press DJ or SAMPLER. Gesture Control Go forward masterpage:Right Swipe in this direction Output “Come On!” Output Reggae Horn sound effect Output Phaser sound effect Output Scratch sound effect Output Audience sound effect The DJ or SAMPLER indicator lights up. 45GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] Notes The DJ EFFECT is automatically turned off when you: turn off the system change the function activate or deactivate the PARTY CHAIN function activate the Football mode select “FIESTA”. select VIDEO sound effect. use the Vocal Fader. change the key (Key Control). If you activate the DJ EFFECT during transferring, the sound effect will not be transferred onto the USB device. Changing the lighting effect You can change the lighting effect when the Party Light is turned on (page 52). Use the buttons and GESTURE CONTROL on the subwoofer to perform this operation. 1 Press GESTURE ON/OFF. The GESTURE CONTROL lights up. 2 Press LIGHT. The LIGHT indicator lights up. 3 Swipe your hand over GESTURE CONTROL to change the lighting effect. The lighting effect changes when you swipe your hand in different direction. masterpage:Left Sound Adjustment Adjusting the sound To Do this Reinforce the Press MEGA BASS on the bass and create a subwoofer repeatedly to more powerful select “BASS ON”. sound Select fiesta sound effect Press FIESTA on the subwoofer. The FIESTA indicator lights up. You can also press MUSIC repeatedly to select “FIESTA”. Select a preset sound effect Press MUSIC or VIDEO repeatedly. To cancel preset sound effect, press MUSIC repeatedly to select “FLAT”. You can also use SOUND FIELD on the subwoofer to select the preset sound effect. Selecting the Virtual Football mode You can experience a feeling of presence in the stadium when watching the football match broadcast. Press FOOTBALL repeatedly while watching a football match broadcast. ON NARRATION: You can enjoy an immersive feeling of being in a football stadium through enhanced stadium cheers. OFF NARRATION: You can enjoy a more immersive feeling of being in a football stadium by minimizing the volume level of narration in addition to the enhancement of cheers. 46GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] To cancel the Virtual Football mode Press MUSIC repeatedly to select “FLAT”. Notes We recommend you to select the football mode when watching a football match broadcast. If you hear unnatural sound in the content when “OFF NARRATION” is selected, “ON NARRATION” is recommended. This feature does not support monaural sound. You can only select the Virtual Football mode during AUDIO IN and TV functions. masterpage:Right Creating your own sound effect You can raise or lower the levels of specific frequency bands, then store the setting in the memory as “CUSTOM EQ”. 1 Press OPTIONS. 2 Press / repeatedly to select “CUSTOM EQ”, then press . 3 Press / repeatedly to adjust the equalizer level, then press . 4 Repeat step 3 to adjust the level of other frequency bands and surround effect. To exit the options menu, press OPTIONS. Adjusting the subwoofer level “S-WOOFER”, then press . To select the custom equalizer setting Press MUSIC repeatedly to select “CUSTOM EQ”. 3 Press / repeatedly to select the subwoofer level, then press . To exit the options menu, press OPTIONS. Sound Adjustment 1 Press OPTIONS. 2 Press / repeatedly to select 47GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] Other Operations Using the Control for HDMI function Connecting a TV compatible with the Control for HDMI function* by HDMI cable (High Speed HDMI Cable with Ethernet, not supplied) enables you to easily operate the device by a TV remote control. The following functions can be used with the Control for HDMI function. System Power Off function System Audio Control function Audio Return Channel One-Touch Play function Remote Easy Control Language Follow * Control for HDMI is a standard used by CEC (Consumer Electronics Control) for allowing HDMI (High-Definition Multimedia Interface) devices to control each other. Note These functions may work with devices other than those manufactured by Sony, but operation is not guaranteed. Preparing to use the Control for HDMI function Set [HDMI SETUP] – [CONTROL FOR HDMI] on the system to [ON] (page 35). The default setting is [ON]. Enable the Control for HDMI function settings for the TV connected to the system. Tip If you enable the Control for HDMI (“BRAVIA” sync) function when using a TV manufactured by Sony, the Control for HDMI function of the system is also enabled automatically. When settings are completed, “COMPLETE” appears in the display panel. masterpage:Left System Power Off function When you turn off the TV, the system will turn off automatically. Set [HDMI SETUP] – [STANDBY LINKED TO TV] on the system to [ON] or [AUTO] (page 35). The default setting is [AUTO]. Note The connected device may not turn off depending on the status of the device. System Audio Control function If you turn on the system while you are watching the TV, the TV sound will be output from the speakers of the system. The volume of the system can be adjusted using the TV’s remote control. If the TV sound was output from the speakers of the system the previous time you watched the TV, the system will be turned on automatically when you turn on the TV again. Operations can also be made by the TV’s menu. For details, refer to the operating instructions of your TV. Notes The system’s volume level is displayed on the TV screen depending on the TV. It may differ from the volume level on the display panel. Depending on the settings of the TV, the System Audio Control function may not be available. For details, refer to the operating instructions of your TV. Audio Return Channel If the system is connected to a TV’s HDMI IN jack compatible with Audio Return Channel, you can listen to TV sound from the speakers of the system without connecting an audio cable (not supplied). On the system, set [HDMI SETUP] – [AUDIO RETURN CHANNEL] to [ON] (page 35). The default setting is [ON]. 48GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] Note If the TV is not compatible with Audio Return Channel, an audio cable (not supplied) needs to be connected (page 23). One-Touch Play function When you play content on the system, the TV is turned on automatically. The TV’s input is switched to the HDMI input which the system is connected. Note Depending on the TV, the beginning part of content being played may not play correctly. Remote Easy Control You can select the system by the SYNC MENU button on the TV remote control and operate the system. This function can be used if the TV supports the link menu. For details, refer to the operating instructions of your TV. masterpage:Right Using the Party Chain function You can connect multiple audio systems in a chain to create a more interesting party environment and to produce higher sound output. Activate a system in the chain to be the “Party Host” and share the music. Other systems will become “Party Guest” and play the same music as the “Party Host”. Setting up the Party Chain Set up a Party Chain by connecting all the systems using audio cords (not supplied). Before connecting cords, be sure to disconnect the AC power cord (mains lead). If all the systems are equipped with Party Chain function Notes In the TV’s link menu, the system is Other Operations recognized by the TV as “Player”. Some operations may not be available First system with some TVs. Language Follow When you change the language for the on-screen display of the TV, the system’s on-screen display language is also changed. Second system Continue the connection until the last system Last system 49GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] The last system must be connected to the first system. Any system can become a Party Host. You can select a new Party Host when Party Chain function is activated. For details, see “To select a new Party Host” (page 51). If one of the system is not equipped with Party Chain function First system Second system Continue the connection until the last system masterpage:Left Enjoying the Party Chain Use the buttons on the subwoofer to perform this operation. 1 Plug in the AC power cord (mains lead) and turn on all the systems. 2 Adjust the volume on each system. 3 Activate the Party Chain function on the system which you want it to be the Party Host. Press FUNCTION repeatedly to select the function you want (except AUDIO IN in connection (page 49)). Start playback the music, then press PARTY CHAIN. “PARTY CHAIN” appears in the display panel. The system starts the party as Party Host and other systems will become Party Guest automatically. All systems play the same music as the Party Host. Notes Last system The last system is not connected to the first system. Connect the system which is not equipped with Party Chain function at the last system. Be sure to select the audio in function on the last system. You must select the first system as Party Host so that all systems are playing the same music when Party Chain function is activated. Depending on the total unit of systems you have connected, Party Guest may take some time to start playing the music. Changing the volume level and sound effect on the Party Host will not affect the output on the Party Guest. The Party Guest continues playing the music source as Party Host even when you change the function on Party Guest. However, you can adjust the volume and change the sound effect on Party Guest. When you use the microphone on Party Host, the sound will not be output from Party Guest. When one of the system in the connection is performing USB transfer, wait the system to complete or stop the transfer before you activate the Party Chain function. For detailed operation on other systems, refer to the operating instructions of the systems. 50GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] To select a new Party Host Repeat step 3 of “Enjoying the Party Chain” on the system which you want it to be a new Party Host. The current Party Host will become Party Guest automatically. All systems play the same music as the new Party Host. Notes You can only select another system as the new Party Host after all the systems have completed the Party Chain function. Repeat the step above if the selected system does not change as a new Party Host after a few seconds. To deactivate the Party Chain On the Party Host, press PARTY CHAIN. Note Repeat the step above if the system does not deactivate the Party Chain after a few seconds. masterpage:Right Singing along: Karaoke Preparing for karaoke 1 Turn MIC LEVEL on the subwoofer anticlockwise to reduce the microphone volume level. 2 Connect an optional microphone to MIC1 or MIC2 jack on the subwoofer. Connect another optional microphone if you want to sing in duet. 3 Start playing the music and adjust the microphone volume. Press MIC ECHO repeatedly to adjust the echo effect. 4 Start singing along with the music. Notes Setting the Party Chain sound mode If howling occurs: 1 Press OPTIONS. 2 Press / repeatedly to select “P CHAIN MODE”, then press 3 Press . / repeatedly to select the mode you want, then press . STEREO: outputs the stereo sound. RIGHT CH: outputs the monaural sound of the right channel. LEFT CH: outputs the monaural sound of the left channel. To exit the options menu, press OPTIONS. Other Operations You can set the sound mode when the Party Chain function is activated. move the microphone away from the speakers. change the direction of the microphone. lower the MIC LEVEL. press – to reduce the volume level or press MIC ECHO repeatedly to adjust the echo level. The sound from the microphone will not be transferred to the USB device during USB transfer. Using Vocal Fader You can reduce the sound of the vocal in stereo source. Press VOCAL FADER repeatedly to select “ON V FADER”. To cancel Vocal Fader effect, press VOCAL FADER repeatedly to select “OFF”. 51GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] Changing the key (Key Control) Press KEY CONTROL / to suit your vocal range. Checking your score Your score is calculated from a scale of 0 to 99 by comparing your voice with the music source. 1 Start playing the music. 2 Press SCORE before singing a song. 3 After singing for more than a minute, press SCORE again to view your score. masterpage:Left Using the Sleep Timer The system turns off automatically after the preset time. Press SLEEP repeatedly. To cancel Sleep Timer, press SLEEP repeatedly to select “OFF”. Tip To check the remaining time before the system turns off, press SLEEP. Using optional equipment 1 Press – repeatedly until “VOL MIN” appears in the display panel. 2 Connect an optional equipment Enjoying the Party Light Press PARTY LIGHT repeatedly to select “LED ON”. Press LIGHT MODE repeatedly to change the illumination mode. To turn off Party Light, press PARTY LIGHT repeatedly to select “LED OFF”. Notes If the illumination brightness is glaring, switch on the room lights or turn off the illumination. You can turn on or off the Party Light when demonstration is turned on. To change the lighting effect See page 46. (page 22). 3 Press FUNCTION +/– repeatedly to select the function which corresponds to the connected equipment. 4 Start playing the connected equipment. 5 Press + repeatedly to adjust the volume. Note The system may enter standby mode automatically if the volume level of the connected equipment is too low. Adjust the volume level of the equipment. To turn off automatic standby function, see “Setting the automatic standby function” (page 53). 52GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\080SND.fm] masterpage:Right Notes Deactivating the buttons on the subwoofer “AutoSTBY” flashes in the display panel (Child Lock) You can deactivate the buttons on the subwoofer (except ) to prevent misoperation, such as child mischief. Hold down on the subwoofer for more than 5 seconds. “CHILD LOCK ON” appears in the display panel. You can only operate the system using the buttons on the remote control. To cancel, hold down on the subwoofer for more than 5 seconds until “CHILD LOCK OFF” appears in the display panel. about 2 minutes before entering standby mode. The automatic standby function does not work in the following cases: during tuner function. when the Sleep Timer is activated. when microphone is connected. Updating the software The software of this system may be updated in the future. You can update the software from the websites below. For customers in Latin America: <http://esupport.sony.com/LA> For customers in Europe and Russia: <http://www.sony.eu/support> For customers in Asia Pacific: <http://www.sony-asia.com/support> Notes Child Lock function will be canceled when you disconnect the AC power cord (mains lead). Child Lock function cannot be activated when you open the disc tray. Follow the online instructions to update the software. Other Operations Setting the automatic standby function The system enters standby mode automatically in about 15 minutes when there is no operation or audio signal output. By default, the automatic standby function is turned on. 1 Press OPTIONS. 2 Press / repeatedly to select “AutoSTBY”, then press . 3 Press / repeatedly to select “ON” or “OFF”. To exit the options menu, press OPTIONS. 53GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Additional Information Troubleshooting Should you encounter a problem with your system, find your problem in the troubleshooting checklist below and take the corrective action. If the problem persists, consult your nearest Sony dealer. Note that if the service personnel changes some parts during repair, these parts may be retained. If “PROTECTX” (X is a number) appears in the display panel Immediately unplug the AC power cord (mains lead), and check the following items. Is anything blocking the ventilation holes of the subwoofer? Is the USB port short-circuited? Are the speaker cables of the speaker system connected to the subwoofer properly? After checking the above items and fixing any problems, plug in the AC power cord (mains lead) again and turn on the system. If the issue persists, consult your nearest Sony dealer. General The power does not turn on. Check that the AC power cord (mains lead) is connected securely. The system has entered standby mode. This is not a malfunction. The system enters standby mode automatically in about 15 minutes when there is no operation or audio signal output (page 53). masterpage:Left There is no sound. Adjust the volume. Check the speaker connections (page 22). Check the connection of the optional equipment, if any (page 22). Turn on the connected equipment. Unplug the AC power cord (mains lead), then plug in the AC power cord (mains lead) again and turn on the system. There is no picture/sound when connected to the HDMI OUT (TV) jack. Change the setting in [HDMI SETUP] – [HDMI RESOLUTION]. The problem may be solved. The equipment connected to the HDMI OUT (TV) jack does not conform to the audio signal format. In this case, set [HDMI SETUP] – [AUDIO(HDMI)] to [PCM]. Try the following: Turn the system off and on again. Turn the connected equipment off and on again. Disconnect and then connect the HDMI cable again. There is no microphone sound. Adjust the microphone volume. Make sure the microphone is connected to the MIC1 or MIC2 jack on the subwoofer correctly. Make sure the microphone is turned on. No TV sound is heard from the system. “CODE 01” and “SGNL ERR” appear in the display panel. This system supports 2-channel Linear PCM formats only. Check the audio output setting on the TV and change it to PCM output mode if automatic mode is selected. Check that the speaker output setting on the TV is set to use external speakers. There is severe hum or noise. Move the system away from sources of noise. 54GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Connect the system to a different wall outlet. Install a noise filter (commercially available) to the AC power cord (mains lead). Turn off surrounding electrical equipment. You can hear a noise from cooling fan when the system is playback at low volume. This is not a malfunction. The remote control does not function. Remove the obstacles between the remote control and the subwoofer. Move the remote control closer to the subwoofer. Point the remote control at the subwoofer’s sensor. Replace the batteries (R03/size AAA). Move the subwoofer away from the fluorescent light. There is acoustic feedback. Reduce the volume. Move the microphone away from the speakers or change the direction of the microphone. “CHILD LOCK” appears when you press any button on the subwoofer. Set the Child Lock function to off (page 53). A clicking sound is heard when turning the power on. This is the operating sound and it occurs when the power is turned on or off, for example. This is not a malfunction. The Gesture Control cannot be activated. Press GESTURE ON/OFF repeatedly until GESTURE CONTROL lights up. Make sure the Child Lock function is not activated (page 53). The Gesture Control does not operate properly. Move your hand closer to GESTURE CONTROL (page 44) when you perform the swiping motion. Perform the swiping motion at a slower speed. Select the correct mode (PLAYBACK, DJ, SAMPLER or LIGHT) before you start using the Gesture Control (page 45, 46). Install a noise filter (commercially available) to the AC power cord (mains lead). Turn off surrounding electrical equipment. Disc player The disc tray does not open and “LOCKED” appears in the display panel. Consult your nearest Sony dealer or local authorized Sony service facility. The disc tray does not close. Load the disc correctly. The disc does not eject. You cannot eject the disc during CD-USB Synchronized Transfer or REC1 Transfer. Press to cancel the transfer, then press on the subwoofer to eject the disc. Consult your nearest Sony dealer. Playback does not start. Wipe the disc clean (page 63). Reload the disc. Load a disc that this system can play back (page 8). Additional Information The color irregularity on a TV screen persists. Turn off the TV at once, then turn it on after 15 to 30 minutes. If the color irregularity still persists, place the system farther away from the TV. masterpage:Right 55GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Remove the disc and wipe away the moisture on the disc, then leave the system turned on for a few hours until the moisture evaporates. The region code on the DVD VIDEO does not match the system. The sound skips. Wipe the disc clean (page 63). Reload the disc. Move the subwoofer to a place with no vibration. Playback does not start from the first track. Set the play mode to Normal Play (page 29). Resume Play has been selected. Press twice. Then, press to start playback. You cannot perform some functions such as Stop, Lock Search, Slowmotion Play, Repeat Play, or Shuffle Play. Depending on the disc, you may not be able to do some of the operations above. Refer to the operating instructions supplied with the disc. The DATA CD/DATA DVD (MP3 or Xvid) cannot be played back. The data is not stored in the supported format. Make sure you have selected the correct Media Mode before playback. The folder name, track name, file name and ID3 tag characters do not appear properly. The ID3 tag is not Version 1 (1.0/1.1) or Version 2 (2.2/2.3). The character codes that can be displayed by this system are as follows: Upper cases (A to Z) Numbers (0 to 9) Symbols (< > * +, [ ] \ _) Other characters appear as “_”. masterpage:Left The sound loses stereo effect when you play back an AUDIO CD, VIDEO CD, audio file, video file, or DVD VIDEO. Unplug all the microphones. “ ” disappears from the display panel. Make sure the system is connected properly. Check the speaker connections (page 22). USB device Transferring results in an error. You are using an unsupported USB device. Check the information on the website about compatible USB devices (page 10). The USB device is not formatted correctly. Refer to the operating instructions of the USB device on how to format. Turn off the system and remove the USB device. If the USB device has a power switch, turn the USB device off and on again after removing it from the system. Then perform the transfer again. If the transfer and erase operations are repeated multiple times, the file structure within the USB device becomes fragmented. Refer to the operating instructions of the USB device on how to deal with this problem. The USB device was disconnected or the power was turned off during transfer. Delete the partiallytransferred file, and perform the transfer again. If this does not fix the problem, the USB device may be broken. Refer to the operating instructions of the USB device on how to deal with this problem. Audio files or folders on the USB device cannot be erased. Check if the USB device is writeprotected. 56GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] The USB device was disconnected or the power was turned off during the erase operation. Delete the partiallyerased file. If this does not fix the problem, the USB device may be broken. Refer to the operating instructions of the USB device on how to deal with this problem. There is no sound. The USB device is not connected correctly. Turn off the system and reconnect the USB device, then turn on the system and check if “USB” appears in the display panel. “READING” is displayed for an extended time, or it takes a long time before playback starts. The reading process can take a long time in the following cases. There are many folders or files on the USB device (page 10). The file structure is extremely complex. The memory capacity is excessive. The internal memory is fragmented. “NO FILE” appears in the display panel. The system has entered the software update mode, all buttons (except ) are deactivated. Press on the subwoofer to cancel the software update. “OVER CURRENT” appears in the display panel. A problem has been detected with the level of electrical current from the (USB) port. Turn off the system and remove the USB device from the port. Make sure there is no problem with the USB device. If this display pattern persists, contact your nearest Sony dealer. Erroneous display. The data stored in the USB device may have been corrupted, perform the transfer again. The character codes that can be displayed by this system are as follows: Upper cases (A to Z) Numbers (0 to 9) Symbols (< > * +, [ ] \ _) Other characters appear as “_”. The USB device is not recognized. Turn off the system and reconnect the USB device, then turn on the system. Check the information on the website about compatible USB devices (page 10). The USB device does not work properly. Refer to the operating instructions of the USB device on how to deal with this problem. Playback does not start. Turn off the system and reconnect the USB device, then turn on the system. Check the information on the website about compatible USB devices (page 10). Additional Information There is noise, skipping, or distorted sound. You are using an unsupported USB device. Check the information on the website about compatible USB devices (page 10). Turn off the system and reconnect the USB device, then turn on the system. The music data itself contains noise, or the sound is distorted. Noise may have entered during the transferring process. Delete the file, and try transferring again. The bit rate used when encoding audio files was low. Send audio files with higher bit rate to the USB device. masterpage:Right 57GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Playback does not start from the first file. Set the play mode to Normal Play (page 29). Files cannot be played back. Make sure you have selected the correct Media Mode before playback. USB devices formatted with file systems other than FAT16 or FAT32 are unsupported.* If you use a partitioned USB device, only files on the first partition can be played back. * This system supports FAT16 and FAT32, but some USB devices may not support all of these FAT. For details, refer the operating instructions of each USB device or contact the manufacturer. Picture There is no picture. Check that the system is connected securely. If the video cable or HDMI cable is damaged, replace it with a new one. Make sure you connect the subwoofer to the HDMI input jack or video input jack of your TV (page 23). Make sure you turn on the TV and operate the TV correctly. Make sure you select the input according to the connection on the TV so that you can view the pictures from the system. (Except for Latin American, European, and Russian models) Make sure you set the color system correctly, according to your TV’s color system. Picture noise appears. Wipe the disc clean (page 63). If video signal from your system has to go through your VCR to your TV, the copy-protection applied to some DVD VIDEO programs could affect the picture quality. masterpage:Left (Except for Latin American, European, and Russian models) When you play back a VIDEO CD recorded in a different color system from the one you set to the system, the picture image may be distorted (pages 25, 33). (Except for Latin American, European, and Russian models) Set the color system to match your TV (pages 25, 33). The aspect ratio of the TV screen cannot be changed. The aspect ratio is fixed on your DVD VIDEO and video file. Depending on the TV, you may not change the aspect ratio. The language for the sound track cannot be changed. Multilingual tracks are not recorded on the DVD VIDEO being played back. The DVD VIDEO prohibits changing the language for the sound track. The subtitles language cannot be changed. Multilingual subtitles are not recorded on the DVD VIDEO being played back. The DVD VIDEO prohibits changing the subtitles. The subtitles cannot be turned off. The DVD VIDEO prohibits turning off subtitles. The angles cannot be changed. Multi-angles are not recorded on the DVD VIDEO being played back. The DVD VIDEO prohibits changing the angles. Tuner* There is severe hum or noise, or stations cannot be received. Connect the antenna properly. Change antenna location and its orientation to obtain good reception. 58GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Turn off surrounding electrical equipment. * Radio may not be received depending on the radio wave conditions or the housing environment in your area. BLUETOOTH device Pairing cannot be performed. Move the BLUETOOTH device closer to the system. Pairing may not be possible if other BLUETOOTH devices are present around the system. In this case, turn off the other BLUETOOTH devices. Make sure the correct passkey was entered at the BLUETOOTH device. The BLUETOOTH device cannot detect the system, or “BT OFF” appears in the display panel. Set the BLUETOOTH signal to “BT ON” (page 43). The sound skips or fluctuates, or the connection is lost. The system and the BLUETOOTH device are too far apart. If there are obstacles between the system and your BLUETOOTH device, remove or avoid the obstacles. If there is equipment that generates electromagnetic radiation, such as a wireless LAN, other BLUETOOTH device, or a microwave oven nearby, move them away. The sound of your BLUETOOTH device cannot be heard on this system. Increase the volume on your BLUETOOTH device first, then adjust the volume using +/–. There is severe hum, noise, or distorted sound. If there are obstacles between the system and your BLUETOOTH device, remove or avoid the obstacles. If there is equipment that generates electromagnetic radiation, such as a wireless LAN, other BLUETOOTH device, or a microwave oven nearby, move them away. Turn down the volume of the connected BLUETOOTH device. The sound from “Voice Playback” in “Fiestable” application does not output. The built-in sound demonstration is activated, press to stop the demonstration. Then, perform the playback again. Control for HDMI (“BRAVIA” Sync) The system does not turn on even when the TV is turned on. Set [HDMI SETUP] – [CONTROL FOR HDMI] to [ON] (page 35). The TV must support the Control for HDMI function (page 48). For details, refer to the operating instructions of your TV. Check the speaker settings of the TV. The system power syncs with the speaker settings of the TV. For details, refer to the operating instructions of your TV. Additional Information Connection is not possible. The BLUETOOTH device you attempted to connect does not support the A2DP profile, and cannot be connected with the system. Enable the BLUETOOTH function of the BLUETOOTH device. Establish a connection from the BLUETOOTH device. The pairing registration information has been erased. Perform the pairing operation again. Erase the pairing registration information of the BLUETOOTH device (page 40) and perform the pairing operation again (page 40). masterpage:Right 59GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] If the sound was output from the speakers of the TV the previous time, the system does not turn on even when the TV is turned on. The system turns off when the TV is turned off. Check the setting of [HDMI SETUP] – [STANDBY LINKED TO TV] (page 35). When [STANDBY LINKED TO TV] is set to [ON], the system turns off automatically when you turn off the TV regardless of the input. The system does not turn off even when the TV is turned off. Check the setting of [HDMI SETUP] – [STANDBY LINKED TO TV] (page 35). To turn the system off automatically regardless of the input when you turn off the TV, set [STANDBY LINKED TO TV] to [ON]. The TV must support the Control for HDMI function (page 48). For details, refer to the operating instructions of your TV. No TV sound is output from the system. Check the type and connection of the HDMI cable or audio cable that is connected to the system and the TV (page 23). If your TV is compatible with Audio Return Channel, make sure the system is connected to an ARCcompatible HDMI IN jack of the TV (page 23). If sound is still not output or if sound is interrupted, connect an audio cable (not supplied) and set [HDMI SETUP] – [AUDIO RETURN CHANNEL] to [OFF] (page 35). If your TV is not compatible with Audio Return Channel, TV sound will not be output from the system even if the system is connected to the TV’s HDMI IN jack. To output TV sound from the system, connect an audio cable (not supplied) (page 23). Switch input of the system to “TV” (page 23). Increase the volume on the system. masterpage:Left Depending on the order in which you connect the TV and the system, the system may be muted and “MUTING” lights up in display panel of the system. If this happens, turn on the TV first, then the system. Set the speakers setting of the TV (BRAVIA) to Audio System. Refer to the operating instructions of your TV on how to set the TV. The sound is output from both the system and the TV. Mute the sound of the system or the TV. Change the speaker output on the TV to TV speaker or Audio System. The Control for HDMI function does not work properly. Check the connection with the system (page 23). Enable the Control for HDMI function on the TV. For details, refer to the operating instructions of your TV. Wait a while, and then try again. If you unplug the system, it will take a while before operations can be made. Wait for 15 seconds or longer, and then try again. Make sure the TV connected to the system support the Control for HDMI function. The type and number of devices that can be controlled by the Control for HDMI function is restricted by the HDMI CEC standard as follows: Recording devices (Blu-ray Disc recorder, DVD recorder, etc.): up to 3 devices Playback devices (Blu-ray Disc Player, DVD player, etc.): up to 3 devices Tuner-related devices: up to 4 devices Audio system (receiver/ headphone): up to 1 device (used by this system) 60GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Party Chain Party Chain function cannot be activated. Check the connections (page 49). Make sure the audio cables are connected correctly. “PARTY CHAIN” is flashing in the display panel. You cannot select AUDIO IN function if you make connection (page 49) during Party Chain function. Select other function (page 50). Press PARTY CHAIN on the subwoofer. Restart the system. Party Chain function does not operate properly. Turn off the system. Then, turn on the system to activate the Party Chain function. To reset the system If the system still does not operate properly, reset the system to factory default settings. Use the buttons on the subwoofer to perform this operation. 1 1 2 Press SETUP. 3 Press / repeatedly to select [RESET], then press . 4 Press / repeatedly to select [YES], then press . It takes a few seconds to complete. Do not press when resetting the system. Press / repeatedly to select [SYSTEM SETUP], then press . Self-diagnosis Function When letters/numbers appear on the TV screen or in the display panel The self-diagnosis function is activated to prevent the system from malfunctioning, a 5-character service number (e.g. C 13 50) with a combination of a letter and 4 digits appears. In this case, check the following table. First 3 characters Cause and corrective of the service action number C 13 This disc is dirty. Clean the disc with a Unplug and plug the AC power cord (mains lead) back in. Press to turn on the system. Hold down ENTER and for about 3 seconds. “RESET” appears in the display panel. All user-configured settings, such as preset radio stations and Sleep Timer are reset to factory default setting (except for SETUP settings). To return the SETUP settings to the default You can return the SETUP settings (except for PARENTAL CONTROL settings) to the default settings. soft cloth (page 63). C 31 The disc is not inserted correctly. Restart the system, then re-insert the disc correctly. E XX (XX is a number) To prevent a malfunction, the system has performed the selfdiagnosis function. Contact your nearest Sony dealer or local authorized Sony service facility and give the 5-character service number. Example: E 61 10 Additional Information 2 3 masterpage:Right 61GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Messages One of the following messages may appear or flash in the display panel during operation. CANNOT PLAY A disc that cannot be played back was inserted. A DVD VIDEO with unsupported region code was inserted. CODE 01 SGNL ERR An unsupported audio signal is input from the connected TV’s HDMI IN (ARC) jack (page 24). DATA ERROR The file does not conform to the required format. The file extensions does not match the file format. DEVICE ERROR The USB device could not be recognized or an unknown device is connected. DEVICE FULL The memory of the USB device is full. ERASE ERROR Erase of audio files or folders on the USB device failed. FATAL ERROR The USB device was removed during transfer or erase operation, and may have been damaged. FOLDER FULL You cannot transfer onto the USB device because the number of folder has reached its maximum. GUEST The system becomes a Party Guest when Party Chain function is activated. masterpage:Left NoDEVICE No USB device is connected or unsupported device is connected. NO DISC There is no disc on the disc tray. NO MUSIC MP3/WMA/AAC/WAV data does not exist in MUSIC playback mode. NO SUPPORT An unsupported USB device is connected or the USB device is connected through a USB hub. NO VIDEO MPEG4/Xvid data does not exist in VIDEO playback mode. NOT USE You tried to perform a specific operation under conditions where that operation is prohibited. OVER CURRENT An over current from the was detected. (USB) port PROTECT The USB device is write-protected. PUSH STOP You tried to perform an operation that can be performed only when the playback is stopped. READING The system is reading information of the disc or USB device. Some operations are not available. REC ERROR The transfer did not start, stopped partway, or otherwise could not be performed. TRACK FULL You cannot transfer onto the USB device because the number of file has reached its maximum. HOST The system becomes a Party Host when Party Chain function is activated. 62GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Precautions When carrying the subwoofer Perform the following procedure to protect the disc mechanism. Use the buttons on the subwoofer to perform this operation. 1 2 Press to turn on the system. 3 Remove the disc. Press to open and close the disc tray. Wait until “NO DISC” appears in the display panel. 4 Unplug the AC power cord (mains lead). Press FUNCTION repeatedly to select “DVD/CD”. Notes on discs Before playing, wipe the disc with a cleaning cloth from the center outward to the edge. Do not clean discs with solvents, such as benzine, thinner, or commercially available cleaners or anti-static spray intended for vinyl LPs. Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Completely disconnect the AC power cord (mains lead) from the wall outlet (mains) if it is not going to be used for an extended period of time. When unplugging the system, always grip the plug. Never pull the cord itself. Should any solid object or liquid get into the system, unplug the system, and have it checked by qualified personnel before operating it again. AC power cord (mains lead) must be changed only at the qualified service shop. On placement Do not place the system in an inclined position or in locations that are extremely hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to vibration, direct sunlight or a bright light. Be careful when placing the system on surfaces that have been specially treated (for example, wax, oil, polish) as staining or discoloration of the surface may result. If the system is brought directly from a cold to a warm location or is placed in a very damp room, moisture may condense on the lens inside the subwoofer, and cause the system to malfunction. In this situation, remove the disc, and leave the system turned on for about an hour until the moisture evaporates. On heat buildup Heat buildup on the subwoofer during operation is normal and is not a cause for alarm. Do not touch the cabinet if it has been used continuously at a high volume because the cabinet may have become hot. Do not obstruct the ventilation holes. On the speaker system This speaker system is not magnetically shielded, and the picture on nearby TV sets may become magnetically distorted. In this situation, turn off the TV, wait 15 to 30 minutes, and turn it back on. If there is no improvement, move the speakers far away from the TV. IMPORTANT NOTICE Caution: If you leave a still video image or on-screen display image displayed on your TV for an extended period of time via this system, you risk permanent damage to your TV screen. Projection TVs are especially susceptible to this. Additional Information On safety masterpage:Right On handling the unit This system is not drip-proof or waterproof. Make sure not to splash water on the system or clean it with water. 63GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] masterpage:Left Cleaning the cabinet This system supports security functions Clean this system with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner, benzine, or alcohol. that comply with the BLUETOOTH specification to ensure secure connection during communication using BLUETOOTH technology. However, this security may be insufficient depending on the setting contents and other factors, so always be careful when performing communication using BLUETOOTH technology. Sony cannot be held liable in any way for damages or other loss resulting from information leaks during communication using BLUETOOTH technology. BLUETOOTH communication is not necessarily guaranteed with all BLUETOOTH devices that have the same profile as this system. BLUETOOTH devices connected with this system must comply with the BLUETOOTH specification prescribed by the Bluetooth SIG, Inc., and must be certified to comply. However, even when a device complies with the BLUETOOTH specification, there may be cases where the characteristics or specifications of the BLUETOOTH device make it impossible to connect, or may result in different control methods, display or operation. Noise may occur or the audio may cut off depending on the BLUETOOTH device connected with this system, the communications environment, or surrounding conditions. On BLUETOOTH communication BLUETOOTH devices should be used within approximately 10 meters (unobstructed distance) of each other. The effective communication range may become shorter under the following conditions. When a person, metal object, wall or other obstruction is between the devices with a BLUETOOTH connection. Locations where a wireless LAN is installed. Around microwave ovens that are in use. Locations where other electromagnetic waves are generated. BLUETOOTH devices and wireless LAN (IEEE 802.11b/g) equipment use the same frequency band (2.4 GHz). When using your BLUETOOTH device near a device with wireless LAN capability, electromagnetic interference may occur. This could result in lower data transfer rates, noise, or inability to connect. If this happens, try the following remedies: Use this system at least 10 meters away from the wireless LAN equipment. Turn off the power to the wireless LAN equipment when using your BLUETOOTH device within 10 meters. Use this system and BLUETOOTH device as close to each other as possible. The radio waves broadcast by this system may interfere with the operation of some medical devices. Since this interference may result in malfunction, always turn off the power on this system and BLUETOOTH device in the following locations: In hospitals, on trains, in airplanes, at gas stations, and any place where flammable gases may be present. Near automatic doors or fire alarms. 64GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] Specifications Active Subwoofer (SA-WGT4D) Speaker section Speaker system Subwoofer, Sound Pressure Horn Speaker unit 250 mm, cone type Rated impedance 4 ohms Inputs AUDIO/PARTY CHAIN IN (TV) L/R Voltage 2 V, impedance 47 kilohms TV (ARC) Supported audio signal: 2-channel Linear PCM MIC1, MIC2 Sensitivity 1 mV, impedance 10 kilohms Outputs HDMI section Connector Type A (19 pin) USB section Supported bit rate WMA: 48 kbps – 192 kbps, VBR, CBR AAC: 48 kbps – 320 kbps, VBR, CBR WAV: 16 bit Sampling frequencies WMA: 44.1 kHz AAC: 44.1 kHz WAV: 44.1 kHz/48 kHz Supported USB device Mass Storage Class Maximum current 1A (USB) port Type A Disc/USB section Supported bit rate MPEG1 Layer-3: 32 kbps – 320 kbps, VBR Sampling frequencies MPEG1 Layer-3: 32 kHz/44.1 kHz/48 kHz Xvid Video codec: Xvid Bit rate: 4.854 Mbps (MAX) Resolution/Frame rate: 720 × 480, 30 fps 720 × 576, 25 fps Audio codec: MP3 MPEG4 File format: MP4 File Format Video codec: MPEG4 Simple Profile (AVC is not compatible.) Bit rate: 4 Mbps Resolution/Frame rate: 720 × 576, 30 fps Audio codec: AAC-LC (HE-AAC is not compatible.) DRM: Not compatible Disc player section System Compact disc and digital audio and video system Additional Information AUDIO/PARTY CHAIN OUT L/R Voltage 2 V, impedance 1 kilohm VIDEO OUT Max. output level 1 Vp-p, unbalanced, Sync. negative load impedance 75 ohms HDMI OUT (TV) Supported audio signal: 2-channel Linear PCM (up to 48 kHz), Dolby Digital masterpage:Right 65GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] masterpage:Left Laser Diode Properties Emission Duration: Continuous Laser Output*: Less than 44.6 W * This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Frequency response 20 Hz – 20 kHz Video color system format NTSC and PAL 3) FM Tuner section Power requirements AC 120 V – 240 V, 50/60 Hz Power consumption 270 W Power consumption (at the Power Saving mode) For European and Russian models only: 0.5 W (When “BT STBY” is set to “OFF” and [CONTROL FOR HDMI] is set to [OFF].) 3 W4) (When “BT STBY” is set to “ON” and [CONTROL FOR HDMI] is set to [ON].) Dimensions (w/h/d) (Approx.) Active subwoofer: 392 mm × 710 mm × 435 mm Speaker unit (left/right): 480 mm × 108 mm × 134 mm Speaker unit (Sound Bar Style): 960 mm × 108 mm × 134 mm Mass (Approx.) Active subwoofer: 23.5 kg Speaker unit (left/right): 3.1 kg System FM stereo, FM superheterodyne tuner Antenna FM lead antenna Tuning range 87.5 MHz – 108.0 MHz (50 kHz step) BLUETOOTH section Communication system BLUETOOTH Standard version 3.0 Output BLUETOOTH Standard Power Class 2 Maximum communication range Line of sight approx. 10 m1) Frequency band 2.4 GHz band (2.4000 GHz – 2.4835 GHz) Modulation method FHSS (Freq Hopping Spread Spectrum) Compatible BLUETOOTH profiles2) A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) SPP (Serial Port Profile) Supported codecs SBC3), AAC, LDAC 1) The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna’s performance, operating system, software application, etc. 2) BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices. Subband Codec Speaker System (SS-GT4DB) Speaker system 2-way, bass reflex Speaker unit (left/right) Tweeters: 40 mm × 1, cone type Midrange: 80 mm × 2, cone type Rated impedance 5 ohms General 4) The power consumption of the system will be less than 0.5 W when there is no HDMI connection and “BT STBY” is set to “OFF”. Design and specifications are subject to change without notice. 66GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] masterpage:Right Language code list The language spellings conform to the ISO 639:1988 (E/F) standard. Code Language Code Language Code Language 1027 Afar 1186 Scots Gaelic 1350 Malayalam Code Language 1513 Siswati 1028 Abkhazian 1194 Galician 1352 Mongolian 1514 Sesotho 1032 Afrikaans 1196 Guarani 1353 Moldavian 1515 Sundanese 1039 Amharic 1203 Gujarati 1356 Marathi 1516 Swedish 1044 Arabic 1209 Hausa 1357 Malay 1517 Swahili 1045 Assamese 1217 Hindi 1358 Maltese 1521 Tamil 1051 Aymara 1226 Croatian 1363 Burmese 1525 Telugu 1052 Azerbaijani 1229 Hungarian 1365 Nauru 1527 Tajik 1053 Bashkir 1233 Armenian 1369 Nepali 1528 Thai 1057 Byelorussian 1235 Interlingua 1376 Dutch 1529 Tigrinya 1059 Bulgarian 1239 Interlingue 1379 Norwegian 1531 Turkmen 1060 Bihari 1245 Inupiak 1393 Occitan 1532 Tagalog 1061 Bislama 1248 Indonesian 1403 (Afan) Oromo 1534 Setswana 1066 Bengali; Bangla 1253 Icelandic 1408 Oriya 1535 Tonga 1067 Tibetan 1254 Italian 1417 Punjabi 1538 Turkish 1070 Breton 1257 Hebrew 1428 Polish 1539 Tsonga 1079 Catalan 1261 Japanese 1435 Pashto; Pushto 1540 Tatar 1093 Corsican 1269 Yiddish 1436 Portuguese 1543 Twi 1557 1097 Czech 1283 Javanese 1463 Quechua 1103 Welsh 1287 Georgian 1481 Rhaeto-Romance 1564 Ukrainian Urdu 1105 Danish 1297 Kazakh 1482 Kirundi 1572 Uzbek 1109 German 1298 Greenlandic 1483 Romanian 1581 Vietnamese Bhutani 1299 Cambodian 1489 Russian 1587 Volapük 1142 Greek 1300 Kannada 1491 Kinyarwanda 1613 Wolof 1144 English 1301 Korean 1495 Sanskrit 1632 Xhosa 1145 Esperanto 1305 Kashmiri 1498 Sindhi 1665 Yoruba 1149 Spanish 1307 Kurdish 1501 Sangho 1684 Chinese 1150 Estonian 1311 Kirghiz 1502 Serbo-Croatian 1697 Zulu 1151 Basque 1313 Latin 1503 Singhalese 1703 Not specified 1157 Persian 1326 Lingala 1505 Slovak 1165 Finnish 1327 Laothian 1506 Slovenian 1166 Fiji 1332 Lithuanian 1507 Samoan 1171 Faroese 1334 Latvian; Lettish 1508 Shona Somali 1174 French 1345 Malagasy 1509 1181 Frisian 1347 Maori 1511 Albanian 1183 Irish 1349 Macedonian 1512 Serbian Additional Information 1130 67GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\090INF.fm] masterpage:Left Parental Control area code list Code Area Code Area Code Area Code Area 2044 Argentina 2165 Finland 2362 Mexico 2149 Spain 2047 Australia 2174 France 2376 Netherlands 2499 Sweden 2046 Austria 2109 Germany 2390 New Zealand 2086 Switzerland 2057 Belgium 2248 India 2379 Norway 2528 Thailand 2070 Brazil 2238 Indonesia 2427 Pakistan 2184 United Kingdom 2079 Canada 2254 Italy 2424 Philippines 2090 Chile 2276 Japan 2436 Portugal 2092 China 2304 Korea 2489 Russia 2115 Denmark 2363 Malaysia 2501 Singapore 68GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\100IND_IX.fm] masterpage:Right Index A M U A/V SYNC 34 AAC file 8 Angles 28 AUDIO 32 AUDIO DRC 34 AUDIO RETURN CHANNEL (ARC) 23, 35, 48 AUDIO SETUP 34 AUDIO(HDMI) 35 MEDIA MODE 26 MEGA BASS 46 MENU 32 MP3 file 8 MPEG4 file 8 MULTI-DISC RESUME 29, 34 Multisession disc 9 Update 53 USB devices 10, 26, 36 USB Transfer 36 Bit rate 36 Erasing 37 REC1 Transfer 36, 37 Synchronized Transfer 36, 37 B BACKGROUND 34 Batteries 24 BLACK LEVEL 33 BLUETOOTH 39 N NFC 12, 42 NFC Easy Connect 42 Normal Play 29 O OSD 32 C P Child Lock 53 COLOR SYSTEM 25, 33 CONTROL FOR HDMI 35, 48 Pairing 40 PARENTAL CONTROL 30, 34 Party Chain 49 Party Light 52 PAUSE MODE 33 PBC playback 28 Playable discs/files 8 Power Saving Mode 25 Preset station 39 D DATA CD 8 DATA DVD 8 Demonstration 25 DJ EFFECT 45 DOWNMIX 34 DVD VIDEO 8 FM MODE 38 G Gesture Control 44 H HDMI RESOLUTION 35 HDMI SETUP 35 K Karaoke 51 Key Control 52 VOCAL FADER 51 L Language code list 67 Language/sound 28 LANGUAGE SETUP 32 VIDEO SETUP 33 Viewing information 31 Display panel 31 TV screen 31 W WAV file 8 WMA file 8 X Xvid file 8 Y YCBCR/RGB(HDMI) 35 Q QUICK setup 25 Additional Information F V R Remote control 13 Repeat Play 30 RESET 34, 61 S SCREEN SAVER 34 Setup Menu 32 Shuffle Play 29 Sleep Timer 52 Sound effect 47 STANDBY LINKED TO TV 35 SUBTITLE 28, 32 SYSTEM SETUP 34 T TRACK SELECTION 34 TV TYPE 33 69GB model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\100IND_IX.fm] masterpage:Right model name [MHC-GT4D] [4-584-051-13(1)] GB filename[D:\NORM'S JOB\SONY HA\SO160005\MHC-GT4D (PMRF 02)\4584051131_GB\110BPG.fm] ©2016 Sony Corporation Printed in Malaysia masterpage:Left 4-584-051-13(1) model name [MHC-GT4D] [4-584-051-13(1)] GB
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021