Specifications | JVC UX-G300 Speaker System User Manual

JVC UX-G300 Speaker System User Manual
Warnings, Cautions and Others
MICRO COMPONENT SYSTEM
UX-G300
—Consists of CA-UXG300 and SP-UXG300
Thank you for purchasing a JVC product.
INSTRUCTIONS
GVT0241-015A[US/UN/UB/UG/A/UW]
0108WMKMDWJMM
©2008 Victor Company of Japan, Limited
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
10 cm or more.
CAUTION:
(Standby/on) button!
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off). When installing the apparatus,
(Standby/
ensure that the plug is easily accessible. The
on) button in any position does not disconnect the mains
line.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Front view
Basic and Common Operations
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
Side view
Press
System Remote
To
STANDBY lamp
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc/USB Mass Storage Class
Device” on page 4.
Press repeatedly to select “FM” or “AM.”
• For “FM/AM,” see “Listening to FM and AM
Broadcasts” on page 5.
See “Listening to Digital Audio Player” on page 5.
Precautions
CAUTION:
• Do not block the ventilation openings or holes. (If
the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get
out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
• Excessive sound pressure from earphones or
headphones can cause hearing loss.
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.
[European Union only]
Adjustable range: Level 0 (“VOL MIN”) to level 40
(“VOL MAX”).
Adjust the volume
Drop the volume in a
moment
Activate the EALA
surround mode
—
Emphasize the
sound (Sound Turbo
function)
Reinforce the bass
sound (Active Hyper
Bass Pro function)
PHONES jack
Stereo mini plug cord
—
—
Change the display
brightness
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start playback.
Press when the System is turned on.
To cancel this function, press again.
For setting the clock, see “Setting the Clock and Using
Timers” on page 6.
—
—
1
Press when the System is on standby.
Setting the save mode allows you to reduce power
consumption by turning the display off while on
standby.
To cancel this function, press again when the System
is on standby.
3
Getting Started
Playing Back a Disc/USB Mass Storage Class Device
Connections
Do not connect the AC power cord until all other connections have been made.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
To connect the AM loop antenna (supplied)
To assemble the AM loop antenna
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
For better FM reception
Outdoor FM antenna
(not supplied)
Basic Disc/USB Mass Storage Class Device Operations
To
Play back the disc
Play back the USB
mass storage class
device
Stop playback
Loading a Disc (on the System only)
Disconnect the supplied FM antenna, and connect to
an outdoor FM antenna using a 75 Ω wire with coaxial
type connector.
When you use the remote control for the first time, pull out
the insulation sheet.
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
FM antenna (supplied)
Prepare the Remote Control
1
Press to open the disc tray.
2
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Select a track
To Replace the Battery in the Remote Control
Press
Indication/Result
• Current track number and elapsed playing
time appear.
For MP3/WMA files: Before current track
number and elapsed playing time appear, the
tag information appears if it is recorded.
• During playback, press again to pause.
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group
(MP3/WMA only)
Rear view
To connect the speaker cords
Select the next groups.
Select the previous groups.
Press to close the disc tray.
3
Lithium coin battery
(product number: CR2025)
Forward search/
Reverse search
Connecting a USB Mass Storage Class Device
Press and hold
Press and hold to fast-forward the track during
playback.
To stop searching, release the button.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
NOTES:
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from over-heating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
• The batteries (battery pack or batteries installed) shall not be
exposed to excessive heat source such as sunshine, fire or the
like.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
—
Change the display
information (Clock and
Source)
Set the Save Mode
NOTE:
Insulation sheet
Press and hold until the AHB indicator lights up.
• When Sound Turbo function is activated (see
above), this function cannot be activated.
To cancel this function, press and hold again when
Sound Turbo function is deactivated.
Press once for adjusting the bass level; twice for treble
level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
Adjust the tone (Bass/
Treble)
There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Supplied Accessories
To restore the volume, press again, or adjust the
volume level.
The
indicator lights up.
To cancel this function, press repeatedly until
indicator lights off.
The S.TURBO indicator lights up.
To cancel this function, press again.
—
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached “Information
about the demonstration function.”)
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXG300U (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from the
factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
• AC plug adapter (× 1) (not applicable for Hong Kong and
Australia)
If anything is missing, consult your dealer immediately.
Indication/Result
USB cable (not supplied)
Release
Insert
NOTES:
Red
To a wall outlet
Plug the AC power cord only after all connections are complete.
• If the wall outlet does not match the AC plug, use the supplied
AC plug adapter (not applicable for Hong Kong and Australia).
From right
speaker
Black
From left
speaker
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
1 m.
• USB mass storage class device is charged through the USB MEMORY terminal when
the System is turned on and the source is “USB.”
• You cannot connect a computer to the USB MEMORY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect and connect the USB mass storage class device again after turning
off the System.
2
RESUME Play (For MP3/WMA only)
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc or USB mass storage class
device.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the stored position.
To clear the stored position, open the disc tray or disconnect the USB mass
storage class device.
• When you clear the stored position and start playback, playback starts from the
beginning of the first track
Press repeatedly to specify the repeat mode as follows:
1
REP TRK: Repeats the current (or specified) track. [ ]
REP GRP: Repeats all tracks in the current group (MP3/WMA
only). [ ]
REP ALL: Repeats all tracks. [ ALL ]
REP OFF: Normal playback
2
or
Programming the Playing Order—Program Play
1
2
3
4
5
or
During stops, press until the PRGM (program) indicator lights
up before playing.
• For MP3/WMA files: Select a group number, then a track
number.
• For CD: Select a track number.
Press to program the selected group/track.
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 51st track, “FULL” will appear.
The tracks are played back in the programmed order.
Operations for Program Play (while not playing)
•
•
•
•
•
To check the programmed contents, press 4 or ¢.
To add tracks, repeat steps 2 and 3 above.
To erase the last programmed track, press CANCEL.
To erase the entire program, press and hold CANCEL for about 2 seconds.
To exit from program play, press MODE.
– The stored program is kept.
Playing at Random—Random Play
1
2
Press until the RND (random) indicator lights up before you start
playback.
Playback starts in random order.
or
Random Play ends when all tracks are played back.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press MODE while playback is stopped.
NOTE:
NOTES:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
Playing Repeatedly—Repeat Play
Prohibiting Disc Ejection (on the System only)
This function does not work in Program Play and Random Play.
You can lock the disc tray so that no one can eject the loaded disc.
• This is possible while the System is on standby.
To cancel the prohibition, repeat the same procedure.
+
4
GVT0241-015A EN_UX-G300[US/UB/UG/A/UW]f
Listening to FM and AM Broadcasts
Listening to Digital Audio Player
The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has
the same or similar button names, they can also be used for the operations.
The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has
the same or similar button names, they can also be used for the operations.
To
Set the AM tuner
intervals to 9 kHz
spacing
Press
Indication/Result
On the System only:
Press and hold 4 DOWN, then press
Digital Audio Player
On the System only:
Press and hold UP ¢, then press
Select FM or AM
Press repeatedly.
• The selected frequency band appear.
Press and hold for more than 2 seconds.
The System starts searching for stations and stops when a station of sufficient
signal strength is tuned in.
• If an FM program is broadcast in stereo, the S (stereo) indicator lights up (only
when the reception is good).
• Press during searching to stop.
• Press repeatedly to change the frequency step by step.
Press to select its preset number.
• For presetting stations, see below.
Select a frequency
or
Tune in to a preset
station
or
Front view
when the System is on standby.
Set the AM tuner
intervals to 10 kHz
spacing
Stereo mini plug cord
(not supplied)
when the System is on standby.
2
3
4
Press repeatedly to select “AUDIO IN.”
Start playing the Digital Audio Player connected.
Adjust the volume.
To Adjust the Audio Input Level
If the sound from the Digital Audio Player connected to the AUDIO IN jack is too loud or too quiet, you can change the audio
input level through the AUDIO IN jack (without changing the volume level).
Press and hold for more than 2 seconds while “AUDIO IN” is selected as the source.
You can select one of three levels as follows:
Press to improve reception.
The M (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press again.
Change the FM
reception mode
(When an FM stereo
broadcast is hard to
receive)
To audio output (or
headphone out, etc.)
Turn the volume to minimum.
1
As the number increases, the sound becomes louder.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry mode.
• Finish the following steps while the indication on the display is flashing.
Press to select a preset number for the station you want to store.
1
2
3
or
Press to store the station.
4
Basic and Common Operations (see page 3)
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
Playing Back a Disc/USB Mass Storage Class Device
Listening to Digital Audio Player
Basic Tuner Operations
Learning More about This System
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used
for MP3/WMA operations.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at bit rate of less than
64 kbps.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
does not include MP3/WMA tracks, they are ignored.
• Do not use the following USB devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabyte.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
• This System can recognize up to 99 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 9 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
Setting the Clock and Using Timers (see page 6)
• You can set the clock and Daily Timer while the Save Mode
is turned on. While setting the clock or Daily Timer, the
display is turning on.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, readjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts playing the
selected source, Daily Timer is canceled.
S.TURBO (Sound Turbo) indicator (See page 3.)
Surround mode indicator (See page 3.)
Play mode indicators (See page 4.)
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of the Daily Timers.
1
Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON time,
DAILY 2 ON time, or DAILY 3 ON time—as follows:
Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.
• “0:00” flashes on the main display until you set the clock.
Press to activate the clock setting mode.
1
2
• If you have already adjusted the clock before, press the button repeatedly until the
clock setting mode is selected.
Adjust the hour, then the minute.
or
• To exit from the clock setting, press CLOCK/TIMER as required.
• To go back to the previous step, press CANCEL.
3
Setting the Sleep Timer
or
1
2
3
4
Adjust the hour then the minute for on-time.
Adjust the hour then the minute for off-time.
Select the playback source—“TUNER-FM,” “TUNER-AM,” “DISC,” “AUDIO IN,” or “USB.”
For “FM/AM”: Select a preset channel.
For “DISC” or “USB”: Select a track. (For MP3/WMA: Select the group, then the track number.)
For “AUDIO IN”: Make the connected device ready for playback.
5 Select the volume.
• You can select the volume level (“VOLUME 0” (VOL MIN) to “VOLUME 40” (VOL MAX) and
“VOLUME – –”). If you select “VOLUME – –,” the volume is set to the last level when the System
is turned off.
Turn off the System (on standby).
• When the on-time comes, the System sets the volume gradually to the preset level.
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the previous step.
When the System is on, press repeatedly to specify the time (in minutes) as follows:
1 Press repeatedly to select “DAILY 1,” “DAILY 2,” or “DAILY 3.”
• To check the remaining time until the System shuts off, press once.
2
Turning Off the System Automatically
—AUTO STANDBY function (only for Disc/USB)
To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.
Press and hold until the A.STBY indicator lights on the display.
• The A.STBY indicator starts flashing after playback stops.
If no operation is done for about 3 minutes, the System turns off.
• Not applicable for FM/AM/AUDIO IN.
To cancel this function, press and hold again.
6
Timer mode indicators
(See page 6.)
SLEEP indicator (See page 6.)
Source indicators (See page 3.)
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Maintenance
To get the best performance of the System, keep your discs
and mechanism clean.
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
\ Electrostatic discharge from your body may cause noise. If
this happens, turn off and on the System again.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
A.STBY (Auto Standby) indicator (See page 6.)
Specifications
Amplifier section
OUTPUT POWER:
60 W (30 W + 30 W) at 4 Ω (10% THD)
Speakers/Impedance:
4 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at “IN LVL1”)
250 mV/47 kΩ (at “IN LVL2”)
125 mV/47 kΩ (at “IN LVL3”)
Digital input:
USB MEMORY
Tuner section
FM tuning range:
AM tuning range:
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
87.50 MHz - 108.00 MHz
530 kHz - 1 710 kHz
(in 10 kHz spacing)
531 kHz - 1 710 kHz
(in 9 kHz spacing)
CD player section
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
To Turn Off the Daily Timer
The SLEEP indicator lights up.
FM reception indicators (See page 5.)
File type indicators (See page 4.)
Troubleshooting
Setting the Clock
Source indicators (See page 3.)
7
Setting the Clock and Using Timers
The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has
the same or similar button names, they can also be used for the operations.
AHB indicator (See page 3.)
Main display
5
2
Display Information
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The disc is recorded with the “packet writing (UDF file
system).” It cannot be played. Check the files you want to
play back.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Sounds from USB mass storage class device are
interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
USB storage
USB specification:
Compatible device:
Compatible file system:
Bus power supply:
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Compatible with USB 2.0 Full
Speed
Mass storage class
FAT16, FAT32
Max. 500 mA
Speakers
Speaker units:
Impedance:
Dimensions (approx.):
Mass (approx.):
JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.
88 dB
85 dB
Immeasurable
10 cm cone x 1
4Ω
160 mm x 250 mm x 150 mm
(W/H/D)
1.6 kg each
General
Power requirements:
AC 110 V - AC 240 V , 50/60 Hz
AC 240 V , 50 Hz (only Australia)
AC 220 V , 50 Hz (only Hong
Kong)
Power supply to USB mass storage class device:
DC 5 V
500 mA
Power consumption:
20 W (power on)
6.5 W (standby mode)
1 W or less (Save Mode)
Dimensions (W x H x D): 165 mm x 251 mm x 269 mm
Mass:
2.6 kg
Specifications and appearance are subject to change
without prior notice.
8
GVT0241-015A EN_UX-G300[US/UB/UG/A/UW]4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising