Kenmore 134313400 Clothes Dryer User Manual

Kenmore 134313400 Clothes Dryer User Manual

INSTALLATION

1. GAS CONNECTION

(Gas dryers only) a. Remove the shipping cap from gas pipe at the rear of the dryer.

NOTE: DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualified gas technician.

b. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for a connection.

Apply an approved thread sealer that is resistant to the corrosive action of liquefied gases on all pipe connections.

c. Open the shutoff valve in the gas supply line.

d. Test all connections by brushing on a soapy water solution. NEVER TEST FOR GAS LEAKS WITH AN

OPEN FLAME.

2. Connect the exhaust duct to outside exhaust system. Use duct tape to seal all joints.

3. With the dryer in its final position, adjust one or more of the legs until the dryer is resting solid on all four legs.

Place a level on top of the dryer. THE DRYER MUST BE

LEVEL AND RESTING SOLID ON ALL FOUR LEGS.

4. Plug the power cord into a grounded outlet. NOTE: Check to ensure the power is off at circuit breaker/fuse box before plugging the power cord into the outlet.

5. Turn on the power at the circuit breaker/fuse box.

Before operating the dryer, make sure the dryer area is clear and free from combustible materials, gasoline, and other flammable vapors. Also see that nothing (such as boxes, clothing, etc.) obstructs the flow of combustion and ventilation air.

6. Run the dryer through a cycle check for proper operation.

NOTE: On gas dryers, before the burner will light, it is necessary for the gas line to be bled of air. If the burner does not light within 45 seconds the first time the dryer is turned on, the safety switch will shut the burner off. If this happens, turn the timer to "OFF" and wait 5 minutes before making another attempt to light.

7. Place these instructions in a location near the dryer for future reference.

NOTE: A wiring diagram is located inside the dryer.

REPLACEMENT PARTS

If replacement parts are needed for your dryer, contact the source where you purchased your dryer, or call Sears Parts and Service Toll Free Number 1-800-4-MY-HOME (1-800-469-

4663).

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage container or make materials inaccessible to children.

The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance.

Lint Blade Retaining Pin Location and Orientation

Install the pins after the lint blade is installed.

8

GREEN

GROUND

SCREW

GREEN

NEUTRAL

GROUND

WIRE

SILVER TERMINAL

GREEN

GROUND

SCREW

GREEN POWER CORD

GROUND WIRE

SILVER TERMINAL

TERMINAL BLOCK

NUT

TIGHTEN NUT

TO THESE

THREADS

GREEN

NEUTRAL

GROUND

WIRE

RED

WHITE

BLACK

TIGHTEN

NUT

TO THESE

THREADS

NUT

STRAIN

RELIEF

MOUNTING

BRACKET

POWER

CORD

STRAIN

RELIEF

MOUNTING

BRACKET

POWER CORD

ELECTRICAL CONNECTIONS

FOR 4-WIRE SYSTEM

ELECTRIC Dryer

ELECTRICAL CONNECTIONS

FOR 3-WIRE SYSTEM

ELECTRIC Dryer

1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2. Install a U.L. listed strain relief in the entry hole of the mounting bracket. Finger tighten the nut only at this time.

3. Remove the green neutral ground wire from the green ground screw located above the terminal block.

1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2. Install a U.L. listed strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time.

3. Thread a U.L. listed 30 amp. power cord, NEMA 10-30

Type SRDT, through the strain relief.

4. Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block.

Tighten the screw securely.

5. Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block.

Tighten both screws securely.

Do not make a sharp bend or crimp wiring/ conductor at connections.

6. Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely.

7. Tighten the screws securing the cord restraint firmly against the power cord.

8. Tighten the strain relief nut securely so that the strain relief does not turn.

9. Reinstall the terminal block cover.

TYPICAL 4

CONDUCTOR

RECEPTACLE

BLACK 240V

WHITE NEUTRAL

RED 240V

TYPICAL 4

CONDUCTOR CORD

GREEN GROUND

30 AMP NEMA 14-30 TYPE SRDT OR ST

7

4. Thread a U.L. listed 30 amp power cord, NEMA 14-30 type ST or SRDT through the strain relief.

5. Attach the green power cord ground wire to the cabinet with the green ground screw.

6. Attach the white (neutral) power cord conductor from the power cord and the green ground wire from the dryer harness (removed from the ground screw in step 3) to the silver-colored center terminal on the terminal block. Tighten the screw securely.

7. Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/ conductor at the connections.

8. Tighten the screws securing the cord restraint firmly against the power cord.

9. Tighten the strain relief nut securely so the strain relief does not turn.

10. Reinstall the terminal block access cover.

ELECTRICAL INSTALLATION

Before proceeding with electrical installation, install the dryer's coin-metering system (when used) in accordance with the separate instructions provided with the meter.

ALL ELECTRIC Dryers

For a permanently connected dryer:

1. The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

The following are specific requirements for proper and safe electrical installation of your dryer.

Failure to follow these instructions can create electrical shock and/or a fire hazard.

ALL GAS Dryers

This dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding.

Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/or fire hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the preinstallation requirements in this manual for the proper power cord to be purchased.

A U.L. listed strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock.

Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper

wired power cord with a copper wired receptacle.

NOTE: Dryers operating on 208 volt power supply will have longer drying times than operating on 240 volt power supply.

GROUNDING REQUIREMENTS

ELECTRIC Dryer

DANGER

Improper connection of the equipment grounding conductor can result in a risk of electrical shock.

Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded.

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current.

2. If your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician.

6

ROUGH-IN DIMENSIONS

4

3/8

>

(11.2)

<

(68.3 cm)

ELECTRIC CONNECTION

UNPACKING

1. Using the four shipping carton corner posts (two on each side), carefully lay the dryer on its left side and remove foam shipping base.

To prevent damage, do not use the control panel or coin meter housing as a means to pick up or move the dryer.

NOTE: On under counter model clothes dryers, the top panel may be removed for installation.

2. Return the dryer to an upright position.

(9.5 cm)

13 1/2"

(34.4 cm)

(6.5 cm)

FOAM

SHIPPING

(110.7 cm)

36"

(91.5 cm)

PACKING

3/8" (0.96 cm) DIA.

GAS PIPE

REAR VIEW

47 1/2"

(120.7 cm)

<

(2.54 cm)

17

(43.2) >

^ 8

(20.4)

v

REVERSING DOOR SWING

Your dryer is designed so the door swing may be reversed at any time without additional parts. Conversion is accomplished by transferring hinges to the opposite side of the cabinet.

To change the direction of the door opening:

1. Open the dryer door. Remove the four hinge hole plugs from the left side of the door opening. Place nearby for future installation. NOTE: You may need a plastic knife to help pull out the plugs. Be careful not to scratch the paint.

2. Remove the four screws that secure the door hinges to the dryer front panel (see below). NOTE: Remove one screw from each of the two hinges first. Hold the door firmly before removing the last two screws.

3. Rotate the door 180° and reinstall the door hinges to the dryer front panel with the four screws.

4. Install the four hinge hole plugs in the open screw holes on the right side of the door opening.

4 3/8"

(11.1 cm)

OPTIONAL

VENT KNOCKOUT

(68.6 cm)

SIDE VIEW

3 3/4"

(9.5 cm)

5

REMOVE 4 SCREWS

(ONE FROM EACH

HINGE FIRST)

LOCATION OF YOUR DRYER

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water or outside weather conditions.

2. In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air.

3. On carpet. Floor MUST be solid with a maximum slope of

1 inch (2.54 cm).

INSTALLATION IN RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom, recess or closet,

MUST be exhausted outdoors.

2. No other fuel burning appliance shall be installed in the same closet as the Gas dryer.

3. Your dryer needs the space around it for proper ventilation.

DO NOT INSTALL YOUR DRYER IN A CLOSET WITH A

SOLID DOOR.

4. A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is required. Air openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable.

MINIMUM INSTALLATION CLEARANCES (Inches)

FRONT SIDES REAR TOP

Alcove

Closet

0 (0 cm) 0 (0 cm) 0 (0 cm) 15 (38.1 cm)

1 (2.54 cm) 0 (0 cm) 0 (0 cm) 15 (38.1 cm)

Closet door ventilation required: 2 louvered openings each 60 square inches (387 square centimeters) — 3 inches (7.6 cm) from bottom and top of door.

THIS DRYER MUST BE EXHAUSTED OUTDOORS.

5. The following illustrations show minimum clearance dimensions for proper operation in a recess or closet installation.

60 SQ. IN.

(387.1 SQ. CM)

0" (0 cm)

15" (38.1 cm)

1" (2.54 cm)

0" (0 cm)

CLOSET DOOR

60 SQ. IN.

(387.1 SQ. CM)

4

Number

of

90°

Turn s

2

3

0

1

4

MAXIMUM LENGTH

of 4” (10.2 cm) Dia. Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

Louvered

4”

(10.2 cm)

60 ft.

(18.28 m)

52 ft.

(15.84 m)

44 ft.

(13.41 m)

32 ft.

(9.75 m)

28 ft.

(8.53 m)

2½"

(6.35 cm)

48 ft.(14.63 m)

40 ft.(12.19 m)

32 ft. (9.75 m)

24 ft. (7.31 m)

16 ft. (4.87 m)

MAXIMUM LENGTH

of 4” (10.2 cm) Dia. Flexible Metal Duct

VENT HOOD TYPE

(Preferred)

Louvered

4”

(10.2 cm)

30 ft.

(9.14 m)

22 ft.

14 ft.

(6.71 m)

(4.27 m)

2½"

(6.35 cm)

18 ft. (5.49 m)

14 ft. (4.27 m)

10 ft. (3.05 m)

NOT RECOMMENDED

• Venting vertical through a roof may expose the ex haust system to down drafts causing an increase in vent restriction.

• Running the exhaust system through an uninsulated area may cause condensation and faster accumu lation of lint.

• Compression or crimping of the exhaust system will cause an increase in vent restriction.

The exhaust system should be inspected and cleaned a minimum of every 6 months with normal usage. The more the dryer is used, the more often you should check the exhaust system and vent hood for proper operation.

EXHAUST DIRECTION

All dryers shipped from the factory are set up for rear exhausting.

However, on electric dryers, exhausting can be to the right or left side of the cabinet or the bottom of the dryer. On gas dryers, exhausting can be to the right side of the cabinet or the bottom of the dryer. Directional exhausting can be accomplished by installing

Exhaust Kit, P/N 131456800, available through your parts distributor. Follow the instructions supplied with the kit.

EXHAUST DUCT LOCATING DIMENSIONS

Number

of

90°

Turns

2

3

0

1

SAME AS OTHER SIDE

CORRECT

INCORRECT

INSTALL MALE FITTINGS IN CORRECT DIRECTION

In installations where the exhaust system is not described in the charts, the following method must be used to determine if the exhaust system is acceptable:

1.

Connect an inclined or digital manometer between the dryer and the point the exhaust connects to the dryer.

2.

Set the dryer timer and temperature to air fluff (cool down) and start the dryer.

3.

Read the measurement on the manometer.

4.

The system back pressure MUST NOT be higher than

0.75 inches of water column. If the system back pressure is less than 0.75 inches of water column, the system is acceptable. If the manometer reading is higher than 0.75 inches of water column, the system is too restrictive and the installation is unacceptable.

Although vertical orientation of the exhaust system is acceptable, certain extenuating circumstances could affect the performance of the dryer:

• Only the rigid metal duct work should be used.

5 7/8"

(15 cm)

13 1/2"

(34 cm)

4 3/8"

(11 cm)

3 3/4"

(9.5 cm)

3 3/4"

(9.5 cm)

GAS SUPPLY REQUIREMENTS

Replace copper connecting pipe that is not plastic-coated. Stainless steel or plastic-coated brass MUST be used.

1. Installation MUST conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1

(latest edition).

2. The gas supply line should be of 1/2 inch (1.27 cm) pipe.

3. If codes allow, flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be constructed of stainless steel or plastic-coated brass.

4. The gas supply line MUST have an individual shutoff valve.

5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping, accessible for test gauge connection, MUST be installed immediately upstream of the gas supply connection to the dryer.

6. The dryer MUST be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa).

3

PRE-INSTALLATION REQUIREMENTS

Tools and Materials Required for Installation:

1. Phillips head screwdriver.

2. Channel-lock adjustable pliers.

3. Carpenter's level.

4. Flat or straight blade screwdriver.

5. Duct tape.

6. Rigid or flexible metal 4 inch (10.2 cm) duct.

7. Vent hood.

8. Pipe thread sealer (Gas).

9. Plastic knife.

POWER SUPPLY CORD - The dryer is equipped with a 120 volt 3-wire power cord.

NOTE: Do not under any circumstances remove grounding prong from plug.

GROUNDING PRONG

ELECTRICAL REQUIREMENTS

ELECTRIC Dryer

EXHAUST SYSTEM REQUIREMENTS

Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible metal duct and approved vent hood which has a swing-out damper(s) that open when the dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet, maintain a minimum of 12 inches (30.5 cm) clearance between the vent hood and the ground or any other obstruction.

CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp.

minimum time delay fuses or circuit breakers.

POWER SUPPLY - 3 wire, 240 volt, single phase, 60 Hz,

Alternating Current.

The following are specific requirements for proper and safe operation of your dryer. Failure to follow these instructions can create excessive drying times and fire hazards.

POWER SUPPLY CORD KIT - The dryer MUST employ a 3conductor power supply cord NEMA 10-30 type SRDT rated at 240 volt AC minimum, 30 amp., with 3 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers, OR a 4-conductor power supply cord NEMA 14-30 type SRDT or ST (as required) rated at 240 volt AC minimum, 30 amp., with 4 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. See ELECTRICAL

CONNECTIONS FOR A 4-WIRE SYSTEM.

Typical 3-wire installation

Do not use plastic flexible duct to exhaust the dryer.

Excessive lint can build up inside exhaust system and create a fire hazard and restrict air flow. Restricted air flow will increase dryer times. If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or flexible metal duct.

Ensure the present duct is free of any lint prior to installing dryer duct.

If the dryer is not exhausted outdoors, some fine lint will be expelled into the laundry area. An accumulation of lint in any area of the building can create a health and fire hazard.

The dryer exhaust system MUST be exhausted to the outside of the building!

OUTLET RECEPTACLE - NEMA 10-30R or 14-30R receptacle to be located so the power supply cord is accessible when the dryer is in the installed position.

POWER SUPPLY

3 WIRE GROUNDED NEUTRAL

120-240 VOLT 60 CYCLE

MAIN FUSE BOX

30 AMP DELAYED ACTION

F U S E S

OR CIRCUIT BREAKER

NEUTRAL WIRE

Do not allow combustible materials (for example: clothing, draperies/curtains, paper) to come in contact with exhaust system. The dryer MUST NOT be exhausted into a chimney, a wall, a ceiling, or any concealed space of a building which can accumulate lint, resulting in a fire hazard.

Exceeding the length of duct pipe or number of elbows allowed in the "MAXIMUM LENGTH" charts can cause an accumulation of lint in the exhaust system. Plugging the system could create a fire hazard, as well as increase drying times.

O U T L E T

RECEPTACLE

(COPPER)

SUBJECT TO LOCAL

REGULATIONS

NEMA 10-30R (COPPER)

GAS Dryer

CIRCUIT - Individual 15 amp. branch circuit fused with a 15 amp. maximum time delay fuse or circuit breaker.

POWER SUPPLY - 3 wire, 120 volt single phase, 60 Hz,

Alternating Current.

2

Do not screen the exhaust ends of the vent system, nor use any screws or rivets to assemble the exhaust system.

Lint can become caught in the screen, on the screws or rivets, clogging the duct work and creating a fire hazard as well as increasing drying times. Use an approved vent hood to terminate the duct outdoors, and seal all joints with duct tape. All male duct pipe fittings MUST be installed downstream with the flow of air.

Explosion hazard. Do not install the dryer where gasoline or other flammables are kept or stored. If the dryer is installed in a garage, it must be a minimum of 18 inches

Installation

Instructions

Gas & Electric

Dryer

Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the dryer is installed correctly and safely. Leave these instructions near the Dryer after installation for future reference.

NOTE: The electrical service to the Dryer must conform with local codes and ordinances and the latest edition of the

National Electrical Code, ANSI/NFPA 70.

NOTE: The gas service to the Dryer must conform with local codes and ordinances and the latest edition of the

National Fuel Gas Code ANSI Z223.1.

For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquid in the vicinity of this or any other machine.

- WHAT TO DO IF YOU SMELL GAS

· Do not try to light any machine.

· Do not touch any electrical switch; do not use any phone in your building.

· Clear the room, building or area of all occupants.

· Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier's instructions.

· If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Printed in U.S.A.

Contents

SUBJECT

Pre-Installation Requirements

Electrical Requirements

Exhaust System Requirements

Gas Supply Requirements

Location of Your Dryer

Rough-In Dimensions

Unpacking

Reversing Door Swing

Electrical Installation

Grounding Requirements

Electrical Connections—3-wire

Electrical Connections—4-wire

Installation

Replacement Parts

Lint Blade Retaining Pin Location

Sears, Roebuck and Co.,

Hoffman Estates, IL 60179 U.S.A.

P/N 134313400 (0309)

PAGE

8

8

8

7

7

6

6

5

5

4

5

2-3

3

2

2

REPAIR

PARTS

LIST

417.74182300

To Call Toll Free

For Parts:

1-800-366-PART

(1-800-366-7278)

For Service:

1-800-4-MY-HOME

®

(1-800-469-4663)

Dryer

When placing a part order, give the complete model number shown on the serial plate located on the inside of the dryer door.

All repair parts listed are available for immediate purchase or special order when you visit your nearest Sears Service Center. To order parts by phone, call the toll free parts number listed to the left.

When requesting service or ordering parts, always provide the following information:

Product Type

Model Number •

• Part Number

Part Description

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

P/N 134316200

Publication number 5995397022

417.74182300

CABINET/DRUM

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

10/03 2

417.74182300

CABINET/DRUM

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

POS. NO

20

21

24

25

29

30

31 #

2

5

6

9

11

12

13

14

15 #

18

42

44

56

57

58

59

64

32

32*

33 #

34

37

40

* #

PART NO

131962400

5303281019

5303281020

131793201

131363200

131825900

131724300

131205400

131600500

131477000

131469100

134122572

131963900

5303015671

131382300

5303201200

134102200

131777700

5303307893

5308015399

131243700

131952100

131841210

134154100

134158000

131949300

131981900

131949400

131686601

131704600

5303281153

DESCRIPTION

Screw,tamper resist ,10-16 x .375

Ball

Clip,ball ,steel ,flat nut

Panel,access ,rear

Cover,terminal block

Bearing,drum support

Bracket,bearing support

Screw,bracket mtg. ,10-16B x 1.375 ,cr/sq drive

Housing,gas heater assy ,w/seal

Screw,10-16AB x 0.375

Bracket,hinge ,rear ,top panel mtg.

Drum,dryer ,painted ,service kit

Glide,drum

Screw,hex washer head ,8-18 x 0 .375 ,cup point

Screw,quadrex head ,10-14 x 1.00 ,vane mtg.,special

Vane,straight

Power Cord,electric svce

Shaft,drum support ,ballhitch

Lubricant,high temp

Thermostat,safety

Screw,pan head ,8-18AB x 0.375 ,cr/sq drive

Duct,heat

Heat Shield

Screw,hex washer head ,10-32 x 0.375 ,ground

Screw,leveling leg

Brace

Spacer,security

Retainer

Bolt,carriage ,3/8-16 x 3.50

Clip

Rear Bearing Kit,includes 5,6 ,12,13,14,18,32

# = Functional Parts

* = Non-Illustrated Parts

3 10/03

417.74182300

FRONT PANEL/LINT FILTER

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

10/03 4

417.74182300

FRONT PANEL/LINT FILTER

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

POS. NO

22*

22*

25

26 #

27

28

41

1

2

6

8

9

16

20

20*

21

22

42

44

46

47

48

49

50

62

PART NO

134063300

131397000

131621902

131622202

134146500

131063700

134036400

5308027429

134134700

131845902

131870700

131474700

131658800

131843100

131450300

5303281074

131627500

131209600

131129900

131644700

131844104

131789303

5303211430

131303300

131872000

DESCRIPTION

Seal,air duct

Plug,dome ,white

Duct,air

Cover,lint housing

Plug,hinge hole ,white

Clip,wiring

Seal,felt ,upper

Adhesive,high temp

Seal,felt ,lower

Panel,front ,white ,with lamp hole

Plug,light hole

Insulation

Door Catch

Switch,door ,w/o drum light

Trap,lint blade assy

Clip,guide ,(3)

Hinge,door

Screw,flat head ,8-18AB x 0.44 ,cr/sq drive

Gasket,door seal

Handle,door ,white

Panel,inner door ,white

Panel,outer door ,white

Door Strike

Screw,pan head ,10-16AB x 0.500 ,locking

Pin,retainer ,lint blade

# = Functional Parts

* = Non-Illustrated Parts

5 10/03

417.74182300

CONTROLS/TOP PANEL

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

57

47

58

59

53

61

23

61

48

10/03

7

4

24

66

6

15

10

65

29

17

P16C0217

417.74182300

CONTROLS/TOP PANEL

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

*

*

*

POS. NO

47*

48

53

57

58

59

61

65 #

66

4

7

10 #

15 #

17

23

* #

24

29

47 #

PART NO

131689300

3205821

131469000

131288900

134064501

134028500

134310200

131970200

131666969

134274001

5304435395

134028000

134086822

3205253

131863800

131863700

131901700

131724700

131724800

134313400

5995397022

134308200

DESCRIPTION

Knob,rotary ,white & gray

Clip,top-to-front

Switch,push/start

Switch,temperature

Bracket,control mtg.

Wiring Harness,controls

Wiring Harness,main

Button,push/start ,white

Console,frame ,w/trim & tape

Meter Case,assy

Mounting Hardware,meter case ,security

Gasket,meter housing

Panel,dryer top ,white ,coin-op

Screw,pan head ,6-20B X 0.375

Retainer,button plug

Plug,button

Screw,mcn point ,1/4-20 ,(4)

Light,pilot

Lens,pilot light

Instructions,installation

Repair Parts List

Wiring Diagram

# = Functional Parts

* = Non-Illustrated Parts

7 10/03

417.74182300

MOTOR

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

34

47

10

52

34

15

52

28

23

7

4

27

22

11

25

20

46

48

51

P16M0027

10/03 8

417.74182300

MOTOR

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

POS. NO

27

28 #

34

46

47

48

51

52

4

7

7*

10 #

11

15 #

20

22

23

25 #

PART NO

131435200

131451600

131456800

131775600

131749800

131298400

131017900

131601000

131863002

134163400

134242400

131560100

131243700

134203400

131633300

131168200

134032800

131303100

DESCRIPTION

Lock,blower housing

Tube,exhaust ,rear ,w/mtg bracket

Tube,exhaust ,side/bottom ,Optional Kit

Housing,blower assy ,cover & wheel

Spacer,idler

Thermostat,temp control

Screw,hex head ,1/4-20T x 1.25 ,spacer mtg.,thread cutting

Spring,idler arm

Idler Arm Assy,w/pulley & clip

Belt,dryer

Clamp,motor mtg.

Motor,main drive ,w/pulley

Screw,pan head ,8-18AB x 0.375 ,cr/sq drive

Bracket,motor mtg

Seal,exhaust tube

Screw,pan head ,8-18B x 0.31

Clip,retainer ,idler arm assy

Screw,hex washer head ,10-16AB x 0.625

# = Functional Parts

* = Non-Illustrated Parts

9 10/03

417.74182300

BURNER

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

10/03 10

417.74182300

BURNER

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

POS. NO

71 #

72 #

73 #

74 #

77 #

79 #

80 #

2

34

55 #

61

64

65

66

68

69 #

70 #

* #

PART NO

131168200

131243700

134264700

134122000

134144900

08015112

134128700

134185100

5308015194

5303207409

5303307291

5303307292

5303207410

134192000

134197700

5303281135

134200801

134285300

DESCRIPTION

Screw,pan head ,8-18B x 0.31

Screw,pan head ,8-18AB x 0.375 ,cr/sq drive

Wiring Harness,gas valve

Bracket,burner mtg

Pipe,gas ,right angle

Cap,pipe

Bushing,coupler

Tail Piece,coupling

Union,hex nut

Valve,gas

Coil,secondary

Coil,booster

Orifice,natural gas ,size 44

Ignitor Assy

Burner Assy

Sensor,radiant

Tube,burner ,riveted

LP Conversion Kit

# = Functional Parts

* = Non-Illustrated Parts

11 10/03

417.74182300

WIRING DIAGRAM

CAUTION: Use the Kenmore part number to order parts, not the illustration number.

10/03 12

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement