LevelOne User Manual N_Max WBR-6001

LevelOne User Manual N_Max WBR-6001
LevelOne
User Manual
WBR-6001
N_Max Wireless Broadband Router
Ver. 1.0.0-0801
i
Downloaded from www.Manualslib.com manuals search engine
Safety
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or
modification is made.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1)
2)
3)
4)
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Declaration of conformity
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirement
of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
CE Marking Warning
Hereby, Digital Data Communications, declares that this (Model-no. WBR-6001) is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
The CE-Declaration of Conformity can be downloaded at:
http://www.levelone.eu/support.php
ii
Downloaded from www.Manualslib.com manuals search engine
Table of Content
TABLE OF CONTENT.................................................................................................................V
1. INTRODUCTION.................................................................................................................... 1
USER MANUAL OVERVIEW ............................................................................................................ 1
2. UNPACKING AND SETUP.................................................................................................... 3
FEATURES .................................................................................................................................. 3
PACKAGE CONTENTS ................................................................................................................... 3
3. HARDWARE INSTALLATION............................................................................................... 5
PRODUCT LAYOUT – FRONT VIEW ................................................................................................. 5
PRODUCT LAYOUT – REAR VIEW .................................................................................................. 6
HARDWARE INSTALLATION STEPS .................................................................................................. 6
NETWORK CHECK ........................................................................................................................ 8
4. CONFIGURING WIRELESS ROUTER................................................................................ 10
LED INDICATOR FOR N_MAX WIRELESS ROUTER ........................................................................ 10
LOGIN TO CONFIGURE FROM WIZARD ............................................................................................ 7
BASIC SETTING ......................................................................................................................... 10
Primary Setup – WAN Type, Virtual Computers .................................................................. 10
Static IP Address............................................................................................................... 12
Dynamic IP Address with Road Runner Session Management.(e.g. Telstra BigPond)..... 13
PPP over Ethernet ............................................................................................................ 13
PPTP................................................................................................................................. 13
L2TP ................................................................................................................................. 14
Virtual Computers (Only for Static and dynamic IP address Wan type) ............................ 15
DHCP Server ....................................................................................................................... 16
Wireless setting, 802.1X setting and WDS........................................................................... 17
Change Password................................................................................................................ 25
FORWARDING RULES ................................................................................................................. 26
Virtual Server ....................................................................................................................... 27
Special AP ........................................................................................................................... 28
Miscellaneous Items............................................................................................................. 29
SECURITY SETTINGS .................................................................................................................. 30
Packet Filter ......................................................................................................................... 31
Domain Filter........................................................................................................................ 36
Downloaded from www.Manualslib.com manuals search engine
URL Blocking ....................................................................................................................... 38
MAC Address Control .......................................................................................................... 40
Miscellaneous Items............................................................................................................. 43
ADVANCED SETTINGS ................................................................................................................ 44
System Time ........................................................................................................................ 45
System Log .......................................................................................................................... 46
Dynamic DNS ...................................................................................................................... 47
SNMP Setting ...................................................................................................................... 49
Routing................................................................................................................................. 50
Schedule Rule...................................................................................................................... 52
Qos Rule .............................................................................................................................. 54
TOOLBOX .................................................................................................................................. 55
System Log .......................................................................................................................... 55
Firmware Upgrade ............................................................................................................... 55
Backup Setting ..................................................................................................................... 55
Reset to default .................................................................................................................... 56
Reboot ................................................................................................................................. 56
APPENDIX A 802.1X SETTING ............................................................................................. 57
APPENDIX B WPA-PSK AND WPA ....................................................................................... 62
APPENDIX C FAQ AND TROUBLESHOOTING .................................................................... 73
TECHNICAL SPECIFICATIONS ............................................................................................... 78
vi
Downloaded from www.Manualslib.com manuals search engine
1. Introduction
Congratulations on your purchase of LevelOne N_Max Wireless Broadband Router. This product is
specifically designed for Small Office and Home Office needs. It provides a complete SOHO solution
for Internet surfing, and is easy to configure and operate even for non-technical users. Instructions for
installing and configuring this product can be found in this manual. Before you install and use this
product, please read the manual carefully for fully exploiting the functions of this product.
User Manual Overview
Introduction Describes N_Max Wireless Broadband Router.
Unpacking and Setup Helps user to get started with the basic installation of the N_Max
Wireless Broadband Router.
Hardware Installation Describes the LED indicators of the N_Max Wireless Broadband
Router.
Configuration Describes the functionalities and its settings.
Technical Specifications Lists the technical (general, physical and environmental)
specifications of the N_Max Wireless Broadband Router.
1
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
2. Unpacking and Setup
This chapter provides the package contents and setup information for the N_Max Wireless
Broadband Router.
Features
z
Extended and high-speed wireless connectivity with wireless N technology
z
Advanced QoS Services for Intelligent Internet
z
Backward compliant with IEEE802.11g and 11b standards
z
Operates on the 2.4GHz frequency band
z
Stay Protected with Advanced Network Security
z
WEP and WPA/WPA2-PSK encryption supported along with Wi-Fi Protected Setup
z
Integrate 4-Port Fast Ethernet Switch with 10/100Mbps MDI-MDI-X auto-sensing
z
Built-in NAT function allows multiple PCs and devices to share Internet connection
z
Browser-based interface configuration and management
z
Quick Setup Wizard provides alternative way to manage device
Package Contents
Open the box of the N_Max Wireless Broadband Router and carefully unpack it. The box should
contain the following items:
z
WBR-6001 N_Max Wireless Broadband Router
z
Power Adapter
z
Cat.5 Cable
z
Antenna
z
CD Manual/Utility
z
Quick Installation Guide
If any item is found missing or damaged, please contact your local reseller for replacement.
3
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
3. Hardware Installation
Product Layout – Front View
1) Reset
Press the Reset button to reboot device or restores factory default setting.
2) Status
A blinking light indicates the device is ready
3) WAN
A solid light indicates the WAN port is connected.
4) WLAN
A solid light indicates the Wireless segment is ready. LED blinks during wireless data transmission.
5) LAN LEDs
A solid light indicates to an Ethernet enable computer on ports 1~4.
LED blinks during data transmission.
6) WPS
Wi-Fi Protected Setup push button
5
Downloaded from www.Manualslib.com manuals search engine
Product Layout – Rear View
1) Power Jack
Receptor for the supplied power adapter
2) LAN Ports (1~4)
Connect Ethernet devices such as computers, switches or hubs.
3) WAN Port
The WAN port is the connection for the Ethernet cable to the Cable or DSL Modem.
4) Antenna
Detachable antenna allows users to change antenna if necessary.
Hardware installation steps
Decide where to place your Wireless Broadband Router
You can place your Wireless Broadband Router on a desk or other flat surface. For optimal
performance, place your Wireless Broadband Router in the center of your office (or your home) in a
location that is away from any potential source of interference, such as a metal wall or microwave
oven. This location must be close to power and network connection.
Setup LAN connection
z Wired LAN connection: connects an Ethernet cable from your computer’s Ethernet port to one of
the LAN ports of this product.
z
Wireless LAN connection: locate this product at a proper position to gain the best transmit
performance.
6
Downloaded from www.Manualslib.com manuals search engine
3. Setup WAN connection
Prepare an Ethernet cable for connecting this product to your cable/xDSL modem or Ethernet
backbone.
4. Power on
Connecting the power cord to power inlet and turning the power switch on, this product will
automatically enter the self-test phase. When it is in the self-test phase, the Status indicator will
be lighted ON for about 10 seconds, and then it will be flashed 3 times to indicate that the self-test
operation has finished. Finally, the Status indicator will be continuously flashed once per second
to indicate that this product is in normal operation.
Downloaded from www.Manualslib.com manuals search engine
Network Check
1.
Please make sure your PC can get IP address automatically so the WBR-6001 can communicate
with your PC during configuration.
•
Select “Control Panel” > “Network Connections”.
•
Right click the “Local Area Connection” and choose “Properties”.
•
Select the TCP/IP protocol for your network card.
•
Click on the Properties button. You should then see the following screen and make sure you
have selected “Obtain IP address automatically”
2.
Reboot computer to make sure you have received the IP address correctly.
3.
Start your Web browser. In the Address box, enter WBR-6001’s default IP Address:
http://192.168.0.1
4.
When prompted, use the following default password to login.
Password: password
8
Downloaded from www.Manualslib.com manuals search engine
Default Settings
IP Address
Password
Wireless Mode
SSID
Security
192.168.0.1
password
Enable
WBR-6001
None
Please enter the default system password in lowercase only.
Downloaded from www.Manualslib.com manuals search engine
4. Configuring Wireless Router
LED Indicator for N_Max Wireless Router
LED
Function
Color
Statu
s
Status
System
status
Green
Blinking
Status flashed once per second to indicate system
is alive.
WAN
WAN port
activity
Green
On
The WAN port is linked.
Blinking
The WAN port is sending or receiving data.
Wireless
activity
Green
Blinking
Sending or receiving data via wireless
On
An active station is connected to the corresponding
LAN port.
Blinking
The corresponding LAN port is sending or receiving
data.
On
Data is transmitting in 100Mbps on the
corresponding LAN port.
WLAN
Link.
1~4
Speed
10/100
Link status
Data Rate
Green
Green
Reset
Button
Description
To reset system settings to factory defaults
Special
application
10
Downloaded from www.Manualslib.com manuals search engine
Login to Configure from Wizard
Activate your browser, and disable the proxy or add the IP address of this product into the exceptions.
Then, type this product’s IP address in the Location (for Netscape) or Address (for IE) field and press
ENTER. For example: http://192.168.0.1
After the connection is established, you will see the web user interface of this product. There are two
appearances of web user interface: for general users and for system administrator.
To log in as an administrator, enter the system password (the default password is ”password”) in the
System Password field and click on the Log in button. If the password is correct, the web appearance
will be changed into administrator configure mode. As listed in its main menu, there are several
options for system administration.
The user can setup step by step to finish the connection with Wizard.
7
Downloaded from www.Manualslib.com manuals search engine
Setup Wizard will guide you through a basic configuration procedure step by step. Press ”Next ”
Once the user finishes those steps and the router screen displayed as below. It means that the
Internet connection is now established.
8
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Basic Setting
Please Select “Advanced Setup” to Setup
Primary Setup – WAN Type, Virtual Computers
10
Downloaded from www.Manualslib.com manuals search engine
Press “Change”
Downloaded from www.Manualslib.com manuals search engine
This option is primary to enable this product to work properly. The setting items and the web
appearance depend on the WAN type. Choose correct WAN type before you start.
1. LAN IP Address: the local IP address of this device. The computers on your network must
use the LAN IP address of your product as their Default Gateway. You can change it if necessary.
2. WAN Type: WAN connection type of your ISP. You can click Change button to choose a
correct one from the following four options:
A. Static IP Address: ISP assigns you a static IP address.
B. Dynamic IP Address: Obtain an IP address from ISP automatically.
C. Dynamic IP Address with Road Runner Session Management. (e.g. Telstra BigPond)
D. PPP over Ethernet: Some ISPs require the use of PPPoE to connect to their services.
E. PPTP: Some ISPs require the use of PPTP to connect to their services.
F. L2TP: Some ISPs require the use of L2TP to connect to their services
Static IP Address
WAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS: enter the proper setting
provided by your ISP.
12
Downloaded from www.Manualslib.com manuals search engine
Dynamic IP Address
1. Host Name: optional. Required by some ISPs, for example: @Home.
2. Renew IP Forever: this feature enables this product to renew your IP address automatically when
the lease time is expiring-- even when the system is idle.
Dynamic IP Address with Road Runner Session Management.(e.g. Telstra BigPond)
1. LAN IP Address is the IP address of this product. It must be the default gateway of your
computers.
2.
WAN Type is Dynamic IP Address. If the WAN type is not correct, change it!
3.
Host Name: optional. Required by some ISPs, e.g. @Home.
4.
Renew IP Forever: this feature enable this product renew IP address automatically when the
lease time is being expired even the system is in idle state.
PPP over Ethernet
1. PPPoE Account and Password: the account and password your ISP assigned to you. For security,
this field appears blank. If you don't want to change the password, leave it empty.
2. PPPoE Service Name: optional. Input the service name if your ISP requires it. Otherwise, leave it
blank.
3. Maximum Idle Time: the amount of time of inactivity before disconnecting your PPPoE session.
Set it to zero or enable Auto-reconnect to disable this feature.
4. Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The most common MTU
value is 1492.
5. Connection Control: There are 3 modes to select:
Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Auto-Reconnect (Always-on): The device will link with ISP until the connection is established.
Manually : The device will not make the link until someone clicks the connect-button in the Stauspage.
PPTP
First, please check your ISP assigned and Select Static IP Address or Dynamic IP Address.
Downloaded from www.Manualslib.com manuals search engine
1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned
to you.
2. Server IP Address: the IP address of the PPTP server.
3. PPTP Account and Password: the account and password your ISP assigned to you. If you don't
want to change the password, keep it empty.
3. Connection ID: optional. Input the connection ID if your ISP requires it.
4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or
enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will connect
to ISP automatically, after system is restarted or connection is dropped.
5. Connection Control: There are 3 modes to select:
Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Auto-Reconnect (Always-on):The device will link with ISP until the connection is established.
Manually: The device will not make the link until someone clicks the connect-button in the Status
page.
L2TP
First, please check your ISP assigned and Select Static IP Address or Dynamic IP Address.
For example: Use Static
1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned
to you.
2. Server IP Address: the IP address of the PPTP server.
3. PPTP Account and Password: the account and password your ISP assigned to you. If you don't
want to change the password, keep it empty.
3. Connection ID: optional. Input the connection ID if your ISP requires it.
4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or
enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will connect
to ISP automatically, after system is restarted or connection is dropped.
6. Connection Control: There are 3 modes to select:
Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Auto-Reconnect (Always-on): The device will link with ISP until the connection is established.
Manually: The device will not make the link until someone clicks the connect-button in the Statuspage.
14
Downloaded from www.Manualslib.com manuals search engine
Virtual Computers (Only for Static and dynamic IP address Wan type)
Virtual Computer enables you to use the original NAT feature, and allows you to setup the one-to-one
mapping of multiple global IP address and local IP address.
• Global IP: Enter the global IP address assigned by your ISP.
• Local IP: Enter the local IP address of your LAN PC corresponding to the global IP address.
• Enable: Check this item to enable the Virtual Computer feature.
Downloaded from www.Manualslib.com manuals search engine
DHCP Server
Press “More>>”
1. DHCP Server: Choose “Disable” or “Enable.”
2. Lease time: This is the length of time that the client may use the IP address it has been assigned
by DHCP server.
3. IP pool starting Address/ IP pool starting Address: Whenever there is a request, the DHCP server
will automatically allocate an unused IP address from the IP address pool to the requesting computer.
You must specify the starting and ending address of the IP address pool.
4. Domain Name: Optional, this information will be passed to the client.
5. Primary DNS/Secondary DNS: This feature allows you to assign DNS Servers
6. Primary WINS/Secondary WINS: This feature allows you to assign WINS Servers
7. Gateway: The Gateway Address would be the IP address of an alternate Gateway.
This function enables you to assign another gateway to your PC, when DHCP server offers an IP to
your PC.
16
Downloaded from www.Manualslib.com manuals search engine
Wireless setting, 802.1X setting and WDS
Wireless settings allow you to set the wireless configuration items.
Wireless: The user can enable or disable wireless function.
Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can
roam freely over this product and other Access Points that have the same Network ID. (The factory
setting is “default”)
SSID Broadcast: The router will Broadcast beacons that have some information, including SSID so
that the wireless clients can know how many AP devices by scanning function in the network.
Therefore, this function is disabled; the wireless clients can not find the device from beacons.
Channel: The radio channel number. The permissible channels depend on the Regulatory Domain.
The factory setting is as follow: channel 6 for North America; channel 7 for European (ETSI); channel
7 for Japan.
Downloaded from www.Manualslib.com manuals search engine
Security: Select the data privacy algorithm you want. Enabling the security can protect your data
while it is transferred from one station to another.
There are several security types to use:
WEP:
When you enable the 128 or 64 bit WEP key security, please select one WEP key to be used and
input 26 or 10 hexadecimal (0, 1, 2…8, 9, A, B…F) digits.
802.1X
Check Box was used to switch the function of the 802.1X. When the 802.1X function is enabled, the
Wireless user must authenticate to this router first to use the Network service.
RADIUS Server
IP address or the 802.1X server’s domain-name.
RADIUS Shared Key
Key value shared by the RADIUS server and this router. This key value is consistent with the key
value in the RADIUS server.
18
Downloaded from www.Manualslib.com manuals search engine
WPA-PSK
1. Select Encryption and Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If user selects ASCII, the length of pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
Downloaded from www.Manualslib.com manuals search engine
WPA
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the
Wireless user must authenticate to this router first to use the Network service. RADIUS Server
IP address or the 802.1X server’s domain-name.
Select Encryption and RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If user elects ASCII, the length of pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key
value in the RADIUS server.
WPA2-PSK (AES)
1. Select Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If user selects ASCII, the length of Pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
20
Downloaded from www.Manualslib.com manuals search engine
WPA2 (AES)
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the
Wireless user must authenticate to this router first to use the Network service. RADIUS Server
IP address or the 802.1X server’s domain-name.
Select RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If user selects ASCII, the length of Pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key
value in the RADIUS server.
WPA-PSK /WPA2-PSK
The router will detect automatically which Security type the client uses to encrypt.
1. Select Pre-share Key Mode
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If user selects ASCII, the length of Pre-share key is from 8 to 63.
2. Fill in the key, Ex 12345678
Downloaded from www.Manualslib.com manuals search engine
WPA/WPA2
Check Box was used to switch the function of the WPA. When the WPA function is enabled, the
Wireless user must authenticate to this router first to use the Network service. RADIUS Server
The router will detect automatically which Security type(Wpa-psk version 1 or 2) the client uses to
encrypt.
IP address or the 802.1X server’s domain-name.
Select RADIUS Shared Key
If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2…8, 9, A, B…F) digits
If user selects ASCII, the length of Pre-share key is from 8 to 63.
Key value shared by the RADIUS server and this router. This key value is consistent with the key
value in the RADIUS server.
WPS (WiFi Protection Setup)
WPS is WiFi Protection Setup which is similar to WCN-NET and offers safe and easy way in
Wireless Connection.
22
Downloaded from www.Manualslib.com manuals search engine
WDS (Wireless Distribution System)
WDS operation as defined by the IEEE802.11 standard has been made available. Using WDS it is
possible to wirelessly connect Access Points, and in doing so extend a wired infrastructure to
locations where cabling is not possible or inefficient to implement.
Downloaded from www.Manualslib.com manuals search engine
24
Downloaded from www.Manualslib.com manuals search engine
Change Password
You can change Password here. We strongly recommend you to change the system password for
security reason.
Downloaded from www.Manualslib.com manuals search engine
Forwarding Rules
26
Downloaded from www.Manualslib.com manuals search engine
Virtual Server
This product’s NAT firewall filters out unrecognized packets to protect your Intranet, so all hosts
behind this product are invisible to the outside world. If you wish, you can make some of them
accessible by enabling the Virtual Server Mapping.
A virtual server is defined as a Service Port, and all requests to this port will be redirected to the
computer specified by the Server IP. Virtual Server can work with Scheduling Rules, and give user
more flexibility on Access control. For Detail, please refer to Scheduling Rule.
For example, if you have an FTP server (port 21) at 192.168.0.2, a Web server (port 80) at
192.168.0.3, and a VPN server at 192.168.0.6, then you need to specify the following virtual server
mapping table:
Downloaded from www.Manualslib.com manuals search engine
Service Port
Server IP
Enable
21
192.168.0.2
V
80
192.168.0.3
V
1723
192.168.0.6
V
Special AP
Some applications require multiple connections, like Internet games, Video conferencing, Internet
telephony, etc. Because of the firewall function, these applications cannot work with a pure NAT
router. The Special Applications feature allows some of these applications to work with this product. If
the mechanism of Special Applications fails to make an application work, try setting your computer as
the DMZ host instead.
1. Trigger: the outbound port number issued by the application..
2. Incoming Ports: when the trigger packet is detected, the inbound packets sent to the specified port
numbers are allowed to pass through the firewall.
This product provides some predefined settings Select your application and click Copy to to add the
predefined setting to your list.
Note! At any given time, only one PC can use each Special Application tunnel.
28
Downloaded from www.Manualslib.com manuals search engine
Miscellaneous Items
IP Address of DMZ Host
DMZ (Demilitarized Zone) Host is a host without the protection of firewall. It allows a computer to be
exposed to unrestricted 2-way communication for Internet games, Video conferencing, Internet
telephony and other special applications.
NOTE: This feature should be used only when needed.
Non-standard FTP port
You have to configure this item if you want to access an FTP server whose port number is not 21.
This setting will be lost after rebooting.
Xbox Support
The Xbox is a video game console produced by Microsoft Corporation. Please enable this function
when you play games.
UpnP Setting
Downloaded from www.Manualslib.com manuals search engine
The device also supports this function. If the OS supports this function enable it.
Security Settings
30
Downloaded from www.Manualslib.com manuals search engine
Packet Filter
Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter
applies on all outbound packets. However, Inbound filter applies on packets that destined to Virtual
Servers or DMZ host only. You can select one of the two filtering policies:
1. Allow all to pass except those match the specified rules
2. Deny all to pass except those match the specified rules
You can specify 8 rules for each direction: inbound or outbound. For each rule, you can define the
following:
• Source IP address
• Source port address
• Destination IP address
• Destination port address
• Protocol: TCP or UDP or both.
• Use Rule#
Downloaded from www.Manualslib.com manuals search engine
For source or destination IP address, you can define a single IP address (4.3.2.1) or a range of IP
addresses (4.3.2.1-4.3.2.254). An empty implies all IP addresses.
For source or destination port, you can define a single port (80) or a range of ports (1000-1999). Add
prefix "T" or "U" to specify TCP or UDP protocol. For example, T80, U53, U2000-2999. No prefix
indicates both TCP and UDP are defined. An empty implies all port addresses. Packet Filter can
work with Scheduling Rules, and give user more flexibility on Access control. For Detail, please refer
to Scheduling Rule.
Each rule can be enabled or disabled individually.
Inbound Filter:
To enable Inbound Packet Filter click the check box next to Enable in the Inbound Packet Filter
field.
Suppose you have SMTP Server (25), POP Server (110), Web Server (80), FTP Server (21), and
News Server (119) defined in Virtual Server or DMZ Host.
Example 1:
32
Downloaded from www.Manualslib.com manuals search engine
(1.2.3.100-1.2.3.149) they are allow to send mail (port 25), and browse the Internet (port 80)
(1.2.3.10-1.2.3.20) they can do everything (block nothing)
Others are all blocked.
Example 2:
(1.2.3.100-1.2.3.119) they can do everything except read net news (port 119) and transfer files via
FTP (port 21)
Others are all allowed.
After Inbound Packet Filter setting is configured, click the save button.
Outbound Filter:
To enable Outbound Packet Filter click the check box next to Enable in the Outbound Packet
Filter field.
Example 1:
Downloaded from www.Manualslib.com manuals search engine
(149.161.123.100-149.161.123.149) they are allowed to send mail (port 25), receive mail (port 110),
and browse Internet (port 80); port 53 (DNS) is necessary to resolve the domain name.
(149.161.123.10-149.161.123.20) they can do everything (block nothing)
Others are all blocked.
Example 2:
34
Downloaded from www.Manualslib.com manuals search engine
(149.161.123.100 and 149.161.123.119) They can do everything except read net news (port 119) and
transfer files via FTP (port 21)
Others are allowed
After Outbound Packet Filter setting is configured, click the save button.
Downloaded from www.Manualslib.com manuals search engine
Domain Filter
Domain Filter
Let you prevent users under this device from accessing specific URLs.
Domain Filter Enable
Check if you want to enable Domain Filter.
Log DNS Query
Check if you want to log the action when someone accesses the specific URLs.
Privilege IP Addresses Range
Setting a group of hosts and privilege these hosts to access network without restriction.
Domain Suffix
A suffix of URL to be restricted. For example, ".com", "xxx.com".
Action
When someone is accessing the URL met the domain-suffix, what kind of action you want. Check
drop to block the access. Check log to log these accesses.
Enable
Check to enable each rule.
36
Downloaded from www.Manualslib.com manuals search engine
Example:
In this example:
1. URL include “www.msn.com” will be blocked, and the action will be record in log-file.
2. URL include “www.sina.com” will not be blocked, but the action will be record in log-file.
3. URL include “www.google.com” will be blocked, but the action will not be record in log-file.
4. IP address X.X.X.1~ X.X.X.20 can access network without restriction.
Downloaded from www.Manualslib.com manuals search engine
URL Blocking
URL Blocking will block LAN computers to connect to pre-define Websites.
The major difference between “Domain filter” and “URL Blocking” is Domain filter require user to input
suffix (like .com or .org, etc), while URL Blocking require user to input a keyword only. In other words,
Domain filter can block specific website, while URL Blocking can block hundreds of websites by
simply a keyword.
URL Blocking Enable
Check if you want to enable URL Blocking.
URL
If any part of the Website's URL matches the pre-defined word, the connection will be blocked. For
example, you can use pre-defined word "sex" to block all websites if their URLs contain pre-defined
word "sex".
Enable
Check to enable each rule.
38
Downloaded from www.Manualslib.com manuals search engine
In this example:
1. URL include “msn” will be blocked, and the action will be record in log-file.
2. URL include “sina” will be blocked, but the action will be record in log-file
3. URL include “cnnsi” will not be blocked, but the action will be record in log-file.
4. URL include “espn” will be blocked, but the action will be record in log-file
Downloaded from www.Manualslib.com manuals search engine
MAC Address Control
MAC Address Control allows you to assign different access right for different users and to assign a
specific IP address to a certain MAC address.
MAC Address Control Check “Enable” to enable the “MAC Address Control”. All of the settings in
this page will take effect only when “Enable” is checked.
Connection control Check "Connection control" to enable the controlling of which wired and
wireless clients can connect to this device. If a client is denied to connect to this device, it means the
client can't access to the Internet either. Choose "allow" or "deny" to allow or deny the clients, whose
MAC addresses are not in the "Control table" (please see below), to connect to this device.
Association control Check "Association control" to enable the controlling of which wireless client
can associate to the wireless LAN. If a client is denied to associate to the wireless LAN, it means the
client can't send or receive any data via this device. Choose "allow" or "deny" to allow or deny the
clients, whose MAC addresses are not in the "Control table", to associate to the wireless LAN.
Control table
40
Downloaded from www.Manualslib.com manuals search engine
"Control table" is the table at the bottom of the "MAC Address Control" page. Each row of this table
indicates the MAC address and the expected IP address mapping of a client. There are four columns
in this table:
MAC
Address
MAC address indicates a specific client.
IP Address
Expected IP address of the corresponding client. Keep it empty if you don't care its IP address.
C
When "Connection control" is checked, check "C" will allow the corresponding client to connect
to this device.
A
When "Association control" is checked, check "A" will allow the corresponding client to
associate to the wireless LAN.
In this page, we provide the following Combobox and button to help you to input the MAC address.
You can select a specific client in the “DHCP clients” Combobox, and then click on the “Copy to”
button to copy the MAC address of the client you select to the ID selected in the “ID” Combobox.
Previous page and Next Page To make this setup page simple and clear, we have divided the
“Control table” into several pages. You can use these buttons to navigate to different pages.
Example:
Downloaded from www.Manualslib.com manuals search engine
In this scenario, there are three clients listed in the Control Table. Clients 1 and 2 are wireless, and
client 3 is wired.
1. The "MAC Address Control" function is enabled.
2."Connection control" is enabled, and all of the wired and wireless clients not listed in the "Control
table" are "allowed" to connect to this device.
3."Association control" is enabled, and all of the wireless clients not listed in the "Control table" are
"denied" to associate to the wireless LAN.
4. Clients 1 and 3 have fixed IP address either from the DHCP server of this device or manually
assigned:
ID 1 - "00-12-34-56-78-90" --> 192.168.12.100 ID 3 - "00-98-76-54-32-10" --> 192.168.12.101
Client 2 will obtain its IP address from the IP Address pool specified in the "DHCP Server" page or
can use a manually assigned static IP address.
If, for example, client 3 tries to use an IP address different from the address listed in the Control
table (192.168.12.101), it will be denied to connect to this device.
5. Clients 2 and 3 and other wired clients with a MAC address unspecified in the Control table are all
allowed to connect to this device. But client 1 is denied to connect to this device.
42
Downloaded from www.Manualslib.com manuals search engine
6. Clients 1 and 2 are allowed to associate to the wireless LAN, but a wireless client with a MAC
address not specified in the Control table is denied to associate to the wireless LAN. Client 3 is a
wired client and so is not affected by Association control.
Miscellaneous Items
Remote Administrator Host/Port
In general, only Intranet user can browse the built-in web pages to perform administration task. This
feature enables you to perform administration task from remote host. If this feature is enabled, only
the specified IP address can perform remote administration. If the specified IP address is 0.0.0.0, any
host can connect to this product to perform administration task. You can use subnet mask bits "/nn"
notation to specified a group of trusted IP addresses. For example, "10.1.2.0/24".
When Remote Administration is enabled, the web server port will be shifted to
88. You can change web server port to other port, too.
Downloaded from www.Manualslib.com manuals search engine
Administrator Time-out
The time elapses of no activity to logout automatically. Set it to zero to disable this feature.
Discard PING from WAN side
When this feature is enabled, any host on the WAN cannot ping this product.
SPI Mode
When this feature is enabled, the router will record the packet information pass through the router like
IP address, port address, ACK, SEQ number and so on. And the router will check every incoming
packet to detect if this packet is valid.
DoS Attack Detection
When this feature is enabled, the router will detect and log the DoS attack comes from the Internet.
Currently, the router can detect the following DoS attack: SYN Attack, WinNuke, Port Scan, Ping of
Death, Land Attack etc.
Advanced Settings
44
Downloaded from www.Manualslib.com manuals search engine
System Time
Get Date and Time by NTP Protocol
Select it if you want to Get Date and Time by NTP Protocol.
Time Server
Select a NTP time server to consult UTC time
Time Zone
Select a time zone where this device locates.
Set Date and Time manually
Select it if you want to Set Date and Time manually.
Downloaded from www.Manualslib.com manuals search engine
Set Date and Time manually
Select it if you want to Set Date and Time manually.
Function of Buttons
Sync Now: Synchronize system time with network time server
Daylight Saving: Set up where the location is.
System Log
This page support two methods to export system logs to specific destination by means of syslog(UDP)
and SMTP(TCP). The items you have to setup including:
IP Address for Syslog
Host IP of destination where syslogs will be sent to. Check Enable to enable this function.
E-mail Alert Enable
Check if you want to enable Email alert (send syslog via email).
SMTP Server IP and Port
46
Downloaded from www.Manualslib.com manuals search engine
Input the SMTP server IP and port, which are concated with ':'. If you do not specify port number, the
default value is 25. For example, "mail.your_url.com" or "192.168.1.100:26".
Send E-mail alert to
Send e-mail alert to the recipient who will receive these logs. You can assign more than 1 recipient
by using ';' or ',' to separate these email addresses.
Dynamic DNS
To host your server on a changing IP address, you have to use dynamic domain name service
(DDNS).
So that anyone wishing to reach your host only needs to know the name of it. Dynamic DNS will map
the name of your host to your current IP address, which changes each time you connect your Internet
service provider.
Before you enable Dynamic DNS, you need to register an account on one of these Dynamic DNS
servers that we list in provider field.
Downloaded from www.Manualslib.com manuals search engine
To enable Dynamic DNS click the check box next to Enable in the DDNS field.
Next you can enter the appropriate information about your Dynamic DNS Server.
You have to define:
Provider
Host Name
Username/E-mail
Password/Key
You will get this information when you register an account on a Dynamic DNS server.
Example:
After Dynamic DNS setting is configured, click the save button.
48
Downloaded from www.Manualslib.com manuals search engine
SNMP Setting
In brief, SNMP, the Simple Network Management Protocol, is a protocol designed to give a user the
capability to remotely manage a computer network by polling and setting terminal values and
monitoring network events.
Enable SNMP
You must check either local or remote or both to enable SNMP function. If Local is checked, this
device will response request from LAN. If Remote is checked, this device will response request from
WAN.
Get Community
Setting the community of Get Request your device will response.
Set Community
Setting the community of Set Request your device will accept.
WAN Access IP Address
IF the user wants to limit to specific the IP address to access, please input in the item. The default
0.0.0.0 and means every IP of Internet can get some information of device with SNMP protocol.
Downloaded from www.Manualslib.com manuals search engine
Routing
Routing Tables allow you to determine which physical interface address to use for outgoing IP data
grams. If you have more than one routers and subnets, you will need to enable routing table to allow
packets to find proper routing path and allow different subnets to communicate with each other.
Routing Table settings are settings used to setup the functions of static.
Dynamic Routing
Routing Information Protocol (RIP) will exchange information about destinations for computing routes
throughout the network. Please select RIPv2 only if you have different subnet in your network.
Otherwise, please select RIPv1 if you need this protocol.
Static Routing: For static routing, you can specify up to 8 routing rules. You can enter the destination
IP address, subnet mask, gateway, and hop for each routing rule, and then enable or disable the rule
by checking or un-checking the Enable checkbox.
Example:
50
Downloaded from www.Manualslib.com manuals search engine
Configuration on NAT Router
Destination
SubnetMask
Gateway
Hop
Enabled
192.168.1.0
255.255.255.0
192.168.123.216
1
ˇ
192.168.0.0
255.255.255.0
192.168.123.103
1
ˇ
So if, for example, the client3 wanted to send an IP data gram to 192.168.0.2, it would use the above
table to determine that it had to go via 192.168.123.103 (a gateway),
And if it sends Packets to 192.168.1.11 will go via 192.168.123.216
Each rule can be enabled or disabled individually.
After routing table setting is configured, click the save button.
Downloaded from www.Manualslib.com manuals search engine
Schedule Rule
You can set the schedule time to decide which service will be turned on or off. Select the “enable”
item. Press “Add New Rule”
You can write a rule name and set which day and what time to schedule from “Start Time” to “End
Time”. The following example configure “ftp time” as everyday 14:10 to 16:20
52
Downloaded from www.Manualslib.com manuals search engine
Schedule Enable
Selected if you want to Enable the Scheduler press “Edit”
To edit the schedule rule, press “Delete”
To delete the schedule rule and the rule #of the rules behind the deleted one will decrease one
automatically.
Schedule Rule can be applied to Virtual server and Packet Filter.
Downloaded from www.Manualslib.com manuals search engine
Qos Rule
Local IP:
Please input Client IP, Example: 192.168.12.33.
Remote Priority:
Please input Global IP and port, Example: 168.96.2.3 and port 21
54
Downloaded from www.Manualslib.com manuals search engine
Toolbox
System Log
Firmware Upgrade
You can upgrade firmware by clicking Firmware Upgrade button.
Backup Setting
You can backup your settings by clicking the Backup Setting button and save it as a bin file. Once
you want to restore these settings, please click Firmware Upgrade button and use the bin file you
Downloaded from www.Manualslib.com manuals search engine
saved.
Reset to default
You can also reset this product to factory default by clicking the Reset to default button.
Reboot
You can also reboot this product by clicking the Reboot button.
Miscellaneous Items
MAC Address for Wake-on-LAN
Wake-on-LAN is a technology that enables you to power up a networked device remotely. In order to
enjoy this feature, the target device must be Wake-on-LAN enabled and you have to know the MAC
address of this device, say 00-11-22-33-44-55. Clicking "Wake up" button will make the router to
send the wake-up frame to the target device immediately.
Domain Name or IP Address for Test
Allow you to configure an IP, and ping the device. You can ping a specific IP to test whether it is alive.
56
Downloaded from www.Manualslib.com manuals search engine
Appendix A 802.1x Setting
Figure 1: Testing Environment (Use Windows 2000 Radius Server)
Equipment Details
PC1: Microsoft Windows XP Professional without Service Pack 1 and LevelOne Wireless PCI Card
PC2: Microsoft Windows XP Professional with Service Pack 1a or latter and LevelOne Wireless PCI
Card.
Authentication Server: Windows 2000 RADIUS server with Service Pack 3 and HotFix Q313664.
Note. Windows 2000 RADIUS server only supports PEAP after upgrade to
service pack 3 and HotFix Q313664 (You can get more information from
http://support.microsoft.com/default.aspx?scid=kb; en-us;313664)
DUT Configuration:
1. Enable DHCP server.
2. WAN setting: static IP address.
3. LAN IP address: 192.168.123.254/24.
4. Set RADIUS server IP.
5. Set RADIUS server shared key.
6. Configure WEP key and 802.1X setting.
Downloaded from www.Manualslib.com manuals search engine
The following test will use the inbuilt 802.1X authentication method such as ,EAP_TLS,
PEAP_CHAPv2(Windows XP with SP1 only), and PEAP_TLS(Windows XP with SP1 only) using the
Smart Card or other Certificate of the Windows XP Professional.
DUT and Windows 2000 Radius Server Setup
Setup Windows 2000 RADIUS Server
We have to change authentication method to MD5_Challenge or using smart card or other certificate
on RADIUS server according to the test condition.
Setup DUT
1. Enable the 802.1X (check the “Enable checkbox“).
2. Enter the RADIUS server IP.
3. Enter the shared key. (The key shared by the RADIUS server and DUT).
4. We will change 802.1X encryption key length to fit the variable test condition.
Setup Network adapter on PC
1. Choose the IEEE802.1X as the authentication method. (Fig 2)
2. Choose MD5-Challenge or Smart Card or other Certificate as the EAP type.
3. If choosing use smart card or the certificate as the EAP type, we select to use a certificate on this
computer.
4. We will change EAP type to fit the variable test condition.
Figure 2 is a setting picture of Windows XP without service pack 1. If users
upgrade to service pack 1, then they can’t see MD5-Challenge from EAP type
list any more, but they will get a new Protected EAP (PEAP) option.
58
Downloaded from www.Manualslib.com manuals search engine
Figure 2: Enable IEEE 802.1X access control / Smart card or certificate properties
Windows 2000 RADIUS server Authentication testing:
DUT authenticate PC1 using certificate. (PC2 follows the same test procedures.)
1. Download and install the certificate on PC1. (Fig 4)
2. PC1 chooses the SSID of DUT as the Access Point.
3. Set authentication type of wireless client and RADIUS server both to EAP_TLS.
4. Disable the wireless connection and enable again.
5. The DUT will send the user's certificate to the RADIUS server, and then send the message of
authentication result to PC1. (Fig 5)
6. Windows XP will prompt that the authentication process is success or fail and end the
authentication procedure. ( Fig 6)
7. Terminate the test steps when PC1 get dynamic IP and PING remote host successfully.
Downloaded from www.Manualslib.com manuals search engine
Figure 4: Certificate information on PC1
Figure 5: Authenticating
60
Downloaded from www.Manualslib.com manuals search engine
Figure 6: Authentication success
DUT authenticate PC2 using PEAP-TLS.
1. PC2 chooses the SSID of DUT as the Access Point.
2. Set authentication type of wireless client and RADIUS server both to PEAP_TLS.
3. Disable the wireless connection and enable again.
4. The DUT will send the user's certificate to the RADIUS server, and then send the message of
authentication result to PC2.
5. Windows XP will prompt that the authentication process is success or fail and end the
authentication procedure.
6. Terminate the test steps when PC2 get dynamic IP and PING remote host successfully.
Support Type: The router supports the types of 802.1x Authentication: PEAP-CHAPv2 and
PEAP-TLS.
1. PC1 is on Windows XP platform without Service Pack 1.
2. PC2 is on Windows XP platform with Service Pack 1a.
3. PEAP is supported on Windows XP with Service Pack 1 only.
4. Windows XP with Service Pack 1 allows 802.1x authentication only when data
encryption function is enable.
Downloaded from www.Manualslib.com manuals search engine
Appendix B WPA-PSK and WPA
Wireless Router: LAN IP: 192.168.123.254
WAN IP: 192.168.122.216
Radius Server: 192.168.122.1
User A: XP Wireless Card:Ti-11g
Tool: Odyssey Client Manager
Refer to: www.funk.com
Download: http://www.funk.com/News&Events/ody_c_wpa_preview_pn.asp
Or Another Configuration:
WPA-PSK
In fact, it is not necessary for this function to authenticate by Radius Server, the client and wireless
Router authenticate by them.
62
Downloaded from www.Manualslib.com manuals search engine
Method1:
1. Go to the Web manager of Wireless Router to configure, like below:
2. Go to Odyssey Client Manager, first choose “Network”
Before doing that, you should verify if the software can show the wireless card.
Open “Adapters”
3. Add and edit some settings:
Downloaded from www.Manualslib.com manuals search engine
4. Back to Connection:
Then Select “Connect to network” You will see:
Method2:
1. First, patch windows XP and have to install “Service package 1”
Patch: http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=5039ef4a61e0-4c44-94f0-c25c9de0ace9
64
Downloaded from www.Manualslib.com manuals search engine
2. Then reboot.
3. Setting on the router and client:
Router:
Client:
Go to “Network Connection” and select wireless adapter.
Choose “View available Wireless Networks” like below:
Advanced choose “123kk”
WPA:
For this function, we need the server to authenticate. This function is like 802.1x.
Downloaded from www.Manualslib.com manuals search engine
The above is our environment:
Method 1:
1. The User A or User B have to get certificate from Radius, first.
http://192.168.122.1/certsrv
Account: fae1
Password: fae1
2. Then, Install this certificate and finish.
3. Go to the Web manager of Wireless Router to configure, like below:
66
Downloaded from www.Manualslib.com manuals search engine
4. Go to Odyssey Client Manager, choose “Profiles” and Setup Profile name as “1”
Login name and passwd are fae1 and fae1.
Remember that you get certificate from Radius in Step1.
5. Then Choose “certificate” like above.
Downloaded from www.Manualslib.com manuals search engine
6. Then go to Authentication and first Remove EAP/ TLS and Add EAP/TLS again.
68
Downloaded from www.Manualslib.com manuals search engine
7. Go “Network” and Select “1” and ok
8. Back to Connection and Select “123kk.
If successfully, the wireless client has to authenticate with Radius Server, like below:
Downloaded from www.Manualslib.com manuals search engine
9.Result:
Method 2:
1. The UserA or UserB have to get certificate from Radius, first.
http://192.168.122.1/certsrv
Account: fae1
Password: fae1
2. Then Install this certificate and finish.
3. Setting on the router and client:
Router:
70
Downloaded from www.Manualslib.com manuals search engine
Client:
Go to “Network Connection” and select wireless adapter.
Choose “View available Wireless Networks” like below:
Advanced choose “123kk”
Select “WirelessCA and Enable” in Trusted root certificate authority:
Downloaded from www.Manualslib.com manuals search engine
Then, if the wireless client wants to associate, it has to request to authenticate.
72
Downloaded from www.Manualslib.com manuals search engine
Appendix C FAQ and Troubleshooting
What can I do when I have some trouble at the first time?
1. Why can I not configure the router even if the cable is plugged in the ports of Router and
the led is also light?
A: First, make sure that which port is plugged. If the cable is in the Wan port, please change to plug
in LAN port 1 or LAN port 4:
Then, please check if the Pc gets ip address from Router. Use command mode as below:
If yes, please execute Browser, like Mozilla and key 192.168.123.254 in address.
If not, please ipconfig /release, then ipconfig /renew.
Whatever I setup, the pc can not get ip. Please check Status Led and refer to the Q2:
Downloaded from www.Manualslib.com manuals search engine
2. Why can I not connect the router even if the cable is plugged in LAN port and the led is light?
A: First, please check Status Led. If the device is normal, the led will blink per second.
If not, please check the blinking Status led shows.
There are many abnormal symptoms as below:
Status Led is bright or dark in work: The system hanged up .Suggest powering off and on the
router. But this symptom often occurs, please reset to default or upgrade latest fw to try again.
Status led flashes irregularly: Maybe the root cause is Flash ROM and please press reset Button to
reset to default or try to use Recovery mode. (Refer to Q3 and Q4)
Status flashes very fast while powering on: Maybe the router is the recovery mode and please
refer to Q4.
3. How to reset to factory default?
A: There are 2 methods to reset to default.
Method 1) Restore with RESET button
First, turn off the router and press the RESET button in. And then, power on the router and push the
RESET button down until the Status start flashing, then remove the finger. If LED flashes about 8
times, the RESTORE process is completed. However, if LED flashes 2 times, repeat steps and try
again.
Method 2) Restore directly when the router power on
First, push the RESET button about 5 seconds (Status will start flashing about 5 times), remove the
finger. The RESTORE process is completed.
4. Why can I not connect Internet even though the cables are plugged in WAN port and LAN
port and the LEDs are blink? In addition, Status led is also normal and I can configure web
management?
A: Make sure that the network cable from DSL or Cable modem is plugged in Wan port of Router and
that the network cable from LAN port of router is plugged in Ethernet adapter. Then, please check
which wan type you use. If you are not sure, please call the ISP. Then please go to this page to input
the information of ISP is assigned.
74
Downloaded from www.Manualslib.com manuals search engine
5. When I use Static IP Address to roam Internet, I can access or ping global IP 202.93.91.218,
But I can not access the site that inputs domain name, for example http://espn.com ?
A: Please check the DNS configuration of Static IP Address. Please refer to the information of ISP
and assign one or two in DNS item.
How do I connect router by using wireless?
1. How to start to use wireless?
A: First, make sure that you already installed wireless client device in your computer. Then check the
configuration of wireless router. The default is as below:
About wireless client, you will see wireless icon:
Downloaded from www.Manualslib.com manuals search engine
Then click and will see the AP list that wireless client can be accessed:
If the client can not access your wireless router, please refresh network list again.
Choose the one that you will want to connect and connect:
If successfully, the computer will show
User will also retrieve IP from router:
2. When I use AES encryption of WPA-PSK to connect even if I input the correct pre-share key?
A: First, you must check if the driver of wireless client supports AES encryption. Please refer to the
below:
76
Downloaded from www.Manualslib.com manuals search engine
If SSID is default and click “Properties” to check if the driver of wireless client supports AES
encryption.
3. When I use wireless to connect the router, but I find the signal is very low even if I am close
to the router?
A: Please check if the wireless client is normal, first. If yes, please send the unit to the seller and
verify what the problem is.
Downloaded from www.Manualslib.com manuals search engine
Technical Specifications
General
Model
WBR-6001 N_Max Wireless Broadband Router
Data Transfer Rate
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54Mbps
Max physical rate up to 300 Mbps in 802.11n mode
Transmit Power
802.11b: 17±2dBm
802.11g: 15±2dBm
802.11n: 14±2dBm
Frequency Range
America/ FCC: 2.412~2.462GHz (11 Channels)
Europe/ ETSI: 2.412~2.472GHz (13 Channels)
Modulation Schemes
DBPSK/DQPSK/CCK/OFDM
Channels
1~11 channels (FCC), 1~13 channels (ETSI),
1~14 channels (MKK-Japan)
Security
64/128-bits WEP Encryption, WPA-PSK, WPA2-PSK, WPA, WPA2, 802.x
Diagnostic LED
Reset
Status
WAN
WLAN
LAN LEDs
Antenna
1.8dBi dipole antenna * 2
Physical and Environmental
Driver Support
Windows 2000, Windows XP, Windows Vista
Temperature
Operating: 0° ~ 40° C, Storage: -10° ~ 70° C
Humidity
10% ~ 95% RH, no condensation
Dimensions
170mm (W) x 30(H) x 110 (D)
Certifications
FCC, CE
78
Downloaded from www.Manualslib.com manuals search engine
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement