KEYS Milestone 6200HR treadmill Owner's Manual

MILESTONE 6200HR

TREADMILL

OWNER’S MANUAL

PART# 15-0108

KEYS

Fitness Products, LP

P.O. Box 551239

Dallas, Texas 75239

Table of Contents

Information Page #

Table of Contents 2

Specification Sheet

Important Safety Information

3

4

Before You Start

Warm Up Exercises

Assembly, Moving Instructions

Power Requirements

Console Functions and Descriptions

Program and Operating Instructions

Program Descriptions and Profiles

Belt Adjustments and Tension

Change to MPH or Km/H

Troubleshooting Guide

Parts and Diagrams

Parts List

Warranty Registration (Mail In Form)

18

19

20

15

16

17

7

8

9

5

6

10, 11, 12, & 13

14

Page 2

Specification Sheet

♦

Horsepower (Continuous) 2.5hp

♦

Display Type 5 Window LED

With green pace display

♦

Electronics One touch

♦

Pre-Set Programs 4

♦

Semi-Custom Programs 8

♦

User Programs 2

♦

Heart Rate Program 1

♦

Heart Rate Interactive Yes

♦

Power Incline 12%

♦

Roller Diameter 2.5”

♦

Cushioned Deck Yes

♦

Speed Range 0-10mph

♦

Belt Size 20 x 60”

♦

Front Hand Rails Yes

♦

Side Hand Rails Yes

♦

Foot Print 29 x 71”

♦

Warranty Motor 10 Years

♦

Warranty Parts 2 Years

♦

Warranty Labor 1 Year

♦

Warranty Frame Lifetime

PAGE 3

Important Safety Information

1)

WARNING!

Before using this treadmill or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

2)

WARNING!

To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important to review this manual and the following precautions before operation.

SAFETY PRECAUTIONS AND TIPS

♦

It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar with warnings and safety precautions.

♦

This treadmill has a user maximum capacity of 350 pounds.

♦

The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not be placed in a garage, patio, or near water and should never be used while you are wet. KEYS recommends a treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning.

♦

Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed power cord.

♦

Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with bare feet, sandals, socks or stockings.

♦

Always straddle the belt and allow it to start moving before stepping onto the belt.

♦

Hold on to handrails when adjusting speed, incline, or other controls.

♦

Always examine your treadmill before using to ensure all parts are in working order.

♦

Allow the belt to fully stop before dismounting.

♦

Pets should never be allowed near or on the treadmill.

♦

Do not leave children unsupervised near or on the treadmill.

♦

Never operate the treadmill where oxygen is being administered, or where aerosol products are being used.

♦

Never insert any object or body parts into any opening.

♦

For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time.

♦

Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will void the treadmill warranty.

♦

Never leave the treadmill unattended while it is running.

PAGE 4

Before You Start

Thank you for purchasing a KEYS treadmill! This quality product you have chosen was designed to meet your needs for cardiovascular exercise.

Before you start, please read the Owner’s Manual and become familiar with the operation of your new treadmill.

♦

Remember to take the time to perform the stretching exercises provided to avoid injury.

♦

Do not stand on the walking belt while pressing the Power button or Start/Stop button.

♦

Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds.

♦

If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate.

♦

If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set treadmill programs or start an exercise program without first contacting and receiving approval from your physician.

♦

To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console.

KEYS recommends a sealed water bottle for beverages consumed while using the treadmill.

♦

Please review the following drawing below to familiarize yourself with the listed parts. This manual covers several treadmills, so the one pictured below may not be identical to your particular model.

CONSOLE

ELECTRONIC DISPLAY

WATER BOTTLE HOLDER

(WATER BOTTLE NOT INCLUDED)

SIDE HAND RAILS

MOTOR COVER

WALKING BELT

UPRIGHTS

CIRCUIT BREAKER

REAR ROLLER

ADJUSTMENT BOLTS

WHEEL

FOOT RAILS

PAGE 5

Warm Up Exercises

EXERCISE GUIDELINES

WARNING

! Before beginning this or any exercise program, you should consult your physician. This is especially important for individuals over the age of 35 or individuals with pre-existing health problems.

Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch three times.

TOE TOUCH STRETCH

Stand bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, back of knees, and back.

HAMSTRING STRETCH

Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible.

Hold for 15 counts, then relax. This will stretch your hamstrings, lower back, and groin.

CALF/ACHILLES STRETCH

With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. To cause further stretching of the Achilles tendon, bend your back leg as well. This will stretch your calves, Achilles tendons, and ankles.

QUADRICEPS STRETCH

With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles.

INNER THIGH STRETCH

Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles.

PAGE 6

Assembly Instructions

KEYS treadmills are shipped in one piece to make assembly easy. After opening the box, remove any packing materials from the treadmill. You should find a rear endcap (large plastic piece that fits over the rear roller area), and owner’s manual packet with bolts and screws for assembly. Do not throw away any packing materials until the unit is working properly. Place the base on a clean, level surface. Make sure the electrical cord will easily reach an electrical outlet.

Figure 1 – Assembly for main uprights

1) Have a second person raise the console to the upright position and hold.

2) Insert 3/4” Button Head Bolt into upright bracket and tighten loosely. Repeat for opposite side.

3) Insert the TUBE SPACER inside the upright frame and line up with the bottom hole. Hold tube spacer while inserting the 1 1/2” Button Head Bolt and lightly tighten. Repeat for opposite side.

4) After completing opposite side, tighten all four assembled bolts and the two other button head bolts that were present before starting. Assembly is now complete.

5) Be sure to insert the SAFETY KEY before turning the power on.

Figure 2 – Assembly for rear end cap

To attach the rear end cap:

1) Place plastic rear end cap over exposed rear roller area.

2) Align holes in plastic end cap with pre-drilled holes in frame.

3) Loosely tighten each screw until all four screws are lined up.

4) Tighten all four screws snugly.

CAUTION:

DO NOT OPERATE TREADMILL WITHOUT SECURING REAR

ROLLER HOUSING!!!

Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill.

Assembly is now complete!

Figure 1

Figure 2

PAGE 7

Power Requirements

ARNG!

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A

RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF

YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT

MODIFY THE PLUG PROVIDED WITH THE PRODUCT IF IT WILL NOT FIT THE OUTLET. HAVE

A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current should the treadmill malfunction. This treadmill comes with an electrical cord with an equipmentgrounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in the drawing below.

PAGE 8

Console Functions and Descriptions

There are five display windows on the control panel to provide feedback information.

WORKOUT TIME/PACE WINDOW

♦

TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds)

♦

INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to

0 seconds

♦

PACE: Indicates amount of time required to complete 1 mile at current speed.

SPEED WINDOW

♦

SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments

DISTANCE / CALORIES WINDOW

♦

DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at

10.0

♦

CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time

INCLINE WINDOW

♦

INCLINE: Indicates incline in percent of grade 0-12% in 0.5 increments

CENTER BRICKYARD WINDOW

♦

Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode, shows the change in speed profile across the interval range (1-10) and shows position with a blinking action.

TIME WINDOW

INCLINE WINDOW

CALORIE/DISTANCE WINDOW

CENTER BRICKYARD WINDOW

SPEED WINDOW

PAGE 9

Program and Operating Instructions

♦

QUICK START / MANUAL MODE

♦

Plug into a surge protector outlet. Insert the Safety Key into the treadmill console.

♦

Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.

♦

Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data can be entered. The TIME window will flash.

♦

Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) button.

♦

To end your workout, press START/STOP button. Belt will gradually slow to zero.

♦

To pause your workout, press PAUSE.

♦

To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT WILL

RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUSING.

♦

Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting started. After pressing the POWER button, the time window will blink. Use the SPEED/TIME + or – arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window will now be flashing. Using the same + or – arrows, select the speed for your workout, then press

ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button.

ENTER

INCLINE

PAGE 10

SPEED/TIME

POWER

START/STOP

PAUSE

Program and Operating Instructions

PROGRAM MODE

Plug treadmill into a surge protector outlet . Insert the Safety Key into the treadmill console.

♦

Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.

♦

Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window will flash.

♦

There are four (4) pre-set and eight (8) semi-custom pre-set programs on the MS6200HR. The treadmill includes FAT BURN, CARDIO, WARM-UP, and CROSS TRAINING programs. Select the program by pressing the appropriate button.

♦

Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving.

♦

CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warm-up, Cross

Training) can be customized in the P1 or P2 mode. After making the program selection, the Calorie window will read “OP”. The “OP” refers to “original program” and is preset. The program name you select will display in the diode light beside the program name. Press the same program button once more and the Calorie window will read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode, which will be saved for future workouts.

1) The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press

ENTER PROGRAM.

2) The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your workout.

Press ENTER PROGRAM.

3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press

ENTER PROGRAM.

To start, press the START/STOP button. To access P2 mode, press the selected program button three times (once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings.

♦

TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For instance to change to a new setting in P1-FAT BURN, press the FAT BURN button twice to access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change the program.

DIODE PROGRAM LIGHTS

FAT BURN

CARDIO

WARM UP

POWER

IN-

CROSS TRAINING

USER PROGRAM

ENTER PROGRAM

SPEED

PAGE 11

POWER

START/STOP

PAUSE

Program Instructions Heart rate

See page 13 for pictures and diagrams

HEART RATE MONITOR MODE

The treadmill may at any time be used in the Heart Rate Monitor Mode. If the signal from the chest strap is detected, heart rate BPM will be displayed in the INCLINE window. The incline will only be briefly displayed if manual or program changes are initiated. The Heart Rate program is designed to keep your heart at a desired amount of “beats per minute” by automatically adjusting the incline. For example, you have programmed in a desired heart rate of 125 BPM and your heart rate is only at 110 BPM. If you are wearing the Heart Rate Transmitter, correctly the incline will automatically increase to intensify the work load, causing your heart rate to slowly climb to 125 BPM. The treadmill will attempt to maintain your target heart rate through adjustments to the incline for the remainder of your workout. In the same respect, if your heart rate is above your programmed amount of BPM’s, the incline will automatically decrease to lower your heart rate. You may at any time during the Heart Rate Program adjust/override the speed and/or the incline by simply pressing the correct corresponding button. You may also change your

“Target Heart Rate” at any time by pressing the TARGET UP or TARGET DOWN button.

HEART RATE PROGRAM OPERATION

♦

Plug treadmill into a surge protector outlet. Insert the Safety Key into the treadmill console.

♦

Stand on the treadmill and straddle belt. Attach safety key clip to your clothes.

♦

Press POWER button. Place the Heart Rate Transmitter strap across your chest and connect ends.

(Make sure your skin is moist and the strap is snug for accurate transmission). At this time, if the display is receiving a signal from the chest strap, the incline window will begin to settle on your current heart rate.

♦

Press the HEART RATE CONTROL button to enter the electronics into the Heart Rate Program. The incline window will momentarily flash ‘125’, which is the default program target heart rate.

♦

The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press

ENTER PROGRAM.

♦

The SPEED/TIME window will then blink. Use the same + or – arrows to select the speed for your workout. Press ENTER PROGRAM.

♦

The incline window (if receiving your heart rate accurately) will show current BPM, and the small red light labeled PULSE adjacent to the incline window, will be illuminated. (If the receiver is not receiving an accurate reading, the incline window will be flashing - - - -).

♦

To adjust the pre-set target heart rate press the TARGET +/TARGET– button then press the ENTER

PROGRAM button.

♦

Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving.

♦

Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving.

The small light at the top of the console labeled TARGET will be illuminated if you are at your target.

If you are not, the arrow shaped lights will illuminate and reflect if you are above or below your goal. If you are not within 25 BPM of your “Target heart rate” the program will not work. DO NOT STOP TO

START OVER. Continue exercising and your heart rate will naturally increase. The program will continually monitor your heart rate and periodically adjust the incline up or down to increase or decrease the resistance thereby keeping you at your target zone. At the conclusion of the programmed time the TIME window will flash 00:00 and the CALORIES/DISTANCE window will continue to accumulate values. The treadmill will continue operation until the START/STOP button or the PAUSE button is pressed. Press the

POWER button to turn off the treadmill.

PAGE 12

Program Instructions Heart rate Mode

TIME

TARGET ARROWS

CALROIES/DISTANCE

TARGET DOWN

INCLINE WINDOW

ENTER PROGRAM

POWER

HEART RATE CONTROL

PAGE 13

TARGET UP

POWER

START/STOP

PAUSE

Program Profiles

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Fat Burn Program is designed to vary the treadmill elevation, while maintaining a constant walking belt speed.

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Cardio Program is designed to vary the treadmill Speed, while maintaining a constant Elevation.

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Warm Up Program is designed to gradually increase the treadmill Speed and

Elevation in the first segment (warm up) and gradually decrease the treadmill Speed and Elevation in the last segment (cool down). This is also known as a

Plateau program.

8

7

6

5

12

11

10

9

4

3

2

1

SPEED

INCLINE

1 2 3 4 5 6 7 8 9 10

The Cross Training Program is designed to control the walking belt speed and elevation inversely in alternating segments.

PAGE 14

Belt Adjustment and Tension

WARNING! Do not overtighten rollers! This will cause premature roller bearing failure!

Belt adjustment and tension performs two functions: adjustment for tension and centering. Your new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the procedures below if the belt shifts to the left or right while walking:

WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1)

First, turn treadmill on to run at 1 mph. Using the hex key provided, turn the left rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself by moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions.

WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2)

First, turn the treadmill on to run at 1 mph. Using the hex key provided, turn the right rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center.

Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions.

WALKING BELT IS SLIPPING DURING USE (Diagram 3)

First, unplug the power cord from the surge protector. Using the hex key provided, turn both left and right rear roller adjustment bolts the same distance, usually a ¼ turn in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at

2.5 mph. You should now walk on the belt to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to slip.

♦

♦

Turning the hex key counter clockwise brings the rear rollers and belt towards you.

Turning the hex key clockwise pushes the rear roller and belt away form you.

PAGE 15

Change Miles per hour to Kilometers per hour

Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in kilometers, follow the steps described here:

1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console.

2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the console (see diagram below).

3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window.

4) Pressing the SPEED +/- button will activate your choice.

5) To accept the setting, press the POWER button.

Page 16

Troubleshooting Guide

Treadmill will not start.

1) Is the Safety Key inserted into the treadmill Console?

2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power

Requirements” on page 8)

3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in.

4) Check the house electrical breaker box and the circuit breaker for the room where the treadmill is located. If it has tripped, reset or have an electrician replace the breaker in home.

5) Have an electrician check for inadequate voltage at the outlet.

Treadmill loses power during use.

1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in.

2) Check the house electrical breaker box and the circuit breaker for the room where the treadmill is located. If it has tripped, reset or have an electrician replace the breaker in home.

3) If the treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.

Treadmill walking belt slows during use.

1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less and the surge protector is securely plugged into the outlet.

2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.

Treadmill walking belt slips or is not centered on rear roller.

1) Refer to “Belt Adjustment and Tension” section on page 15.

2) Need help? Call Keys Technical Service at (888) 340-0482.

Treadmill Error Messages.

Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. To avoid possible damage to the treadmill and the possibility of

injury, do not operate the treadmill until the problem is corrected. Call Keys Technical

Service at (888) 340-0482.

Page 17

Parts & Diagrams

5

6

7

1

2

3

4

Left Side Extrusion Rail

Right Side Extrusion Rail

Treadmill Belt

Front Roller Assembly

Rear Roller

Treadmill Deck

Left End Cap

8

9

Right End Cap

Rear Adjustable Foot (2)

10 Main Frame

11 Bottom Motor Pan

Part #

05-0031

05-0031

04-0020

24-0174

09-0020

03-0015

06-0143

06-0143

10-0006 various

06-0145

16

17

18

12

13

14

15

19

20

21

22

Front Wheel (2)

Uprights for Console (2)

Motor Hood Cover Top

Motor Drive Belt

Motor

Elevation Motor (acuator)

Console Assembly

Membrane

Handlebars

Toggle switches (2)

Lower Electronics M/

Control P/Supply

Part #

06-0039 various

06-0146

04-0004

12-0033

12-0022

24-0175

08-0112 various

08-0027

08-0115

Page 18

Milestone 6200HR Parts List

DESCRIPTION

SCREW-8x5/8 PHIL PH AB BLACK

SCREW-8x5/8 PPH HILO BLACK TPB

BOLT-HEX 5/16-18x5 1/2 GRADE 5-ZP

NUT 5/16-18 NYLOCKZP

BOLT-HEX 5/16-18x3/4 GRADE 2-ZP

NUT-HEX 5/16 WIZ-FL-LK-ZP

WASHER LOCK 1/4"

BOLT-HEX 1/4-20x2 1/2" GRADE 5 ZP

WASHER SPRING

BOLT-HEX 3/8-16x2 1/2" GRADE 5

NUT-NYLOCK HEX 3/8-16

NUT-PUSH 3/8 HAT BLACK 375012

SCREW SHCS 1/4-20x2 1/2"

WASHER 9/32 5/8 1/8THICK ZP

NUT-NYLOCK HEX 10-24

CARRIAGE BOLT 5/16x1 GRADE 5 ZP

NUT-T HF 14209H-DB

BOLT-HEX 3/8-16x1 3/4" GRADE 5ZP

WASHER-#10 EXTERNAL STAR

SCREW-PPH 8x5/8 GREEN HEAD

WRENCH-ALLEN 3/16 SHAFT ARM

RETAINER-GUIDE TUBE

SCREW#8x5/8' SD BLACK

NUT-NYLOCK HEX 1/4-20

SCREW-SHCS 1/4-20x3/4"

SCREW-HWH MACH 8-32x3/8"

WASHER-FLAT SAE 5/16

SCREW-BUTTON HEAD 5/16-18x2 1/2'

SCREW-PHTR #8x3/" AB BLACK

WASHER -SFW 3/8X7/8X1/8" THICK

BOLT-CARRIAGE 10-24x3/4'

INDRTY-5/16-18 HEAVY WAL AVK

SCREW-HWH SLOTTED 8-18x3/4' AB ZP

WASHER-FENDER 1/4x1"

NUT RIV 5/16-18 AVAKALS4-518-150

TETHER KILL PIN

PLUG PUSH-IN

SCREW PPH#4x5/8' TYPE AB

PUSH NUT BLACK.112 SHAFT

WALKBOARD KORETRON 60"CONV

BELT POLY V-190J8

WALKBELT 1PLY 19.75x122.75 CONV

EXTRUSION LT&RT SIDE BRD CONV GRAY

BUSHING-STRAIN RELIEF #1237

TIES-WIRE

PAN-END-BASE

CLAMP WIRE 3367 7/16

CLIP-ALLEN WRENCH

WHEEL-KEYS SERIES-2.5"

SUPPORT PC BOARD-HRC

FAN 5"-5/8" ID

BAG-PLASTIC 12x12 3MIL-INST PACKET

SWITC HOUSING ROUND GRAY

TETHER HOUSING FOR WEDGE CONSLE

INSERT LED FOR CONSOLE

CONSOLE WEDGE GRAY

END CAP DUAL GRAY

PULLEY DRIVE 2.5" 8 GROOVE

BOTTOM PAN CONV

COVER FRO MOTOR CONV GRAY

RECEIVER DISCRETE-LED-HRC

ELECTRONICS 5 WIN LED GREEN

CHEST STRAP NO LOGO ALL HR UNITS

02-0103

02-0105

02-0113

02-0123

02-0133

02-0136

02-0137

02-0140

02-0141

03-0015

04-0004

04-0020

05-0031

02-0050

02-0053

02-0054

02-0068

02-0082

02-0092

02-0099

02-0017

02-0018

02-0020

02-0021

02-0022

02-0024

02-0027

02-0031

02-0033

02-0036

02-0038

02-0040

02-0042

PART #

02-0004

02-0005

02-0006

02-0007

02-0008

02-0009

02-0013

02-0014

02-0015

02-0016

06-0014

06-0016

06-0145

06-0021

06-0024

06-0039

06-0058

06-0071

06-0084

06-0117

06-0139

06-0140

06-0142

06-0143

06-0144

06-0145

06-0146

07-0020

07-0050

07-0041

1

2

1

2

13-0046

14-0028

14-0053

14-0054

2 14-0205

1

7 14-0289

14-0321

1

1

4 14-0327

2 14-0337

14-0347

14-0356

1

2

17-0073

17-0030

2

6

17-0061

17-0074

1

1

17-0075

17-0076

17-0077

1 17-0079

2 17-0080

3

8

3

3

9

4

1

QTY PART #

24 08-0106

1

8 08-0112

08-0004

08-0027

08-0047

08-0077

08-0115

09-0020

09-0019

10-0006

4

2

2

2

10-0017

10-0020

2 10-0023

2 10-0024

11-0002

11-0023

8

1

12-0022

12-0033

1 13-0003

1 13-0011

2 13-0014

1 13-0017

1 13-0042

2

2

4

1 18-0008

11 19-0184

1 19-0015

1 19-0019

19-0023

19-0177

19-0106

2 19-0134

1 19-0147

2 19-0187

1 19-0105

1 19-0159

1 19-0007

1

1 19-0073

19-0077

1

1

1 19-0079

1

1 19-0143

19-0144

19-0155

19-0156

DESCRIPTION

LIMIT SWITCH

MEBRANE LED FOR WEDGE CONSOLE

BREAKER-CIRCIT-15AMP

SWITCH-REMOTE-W/HARNESS

ENCODER-OPTICAL-ALEPH

CORE-ERRITE

CONTROLLER 08-0050 W/OUT SWITCH

ROLLER REAR 2.5"x24.5" CONV/FOLD

FROLLER FRONT 2.5x24.5" CONV

TIP-CRUNCH 1" CNV

TAPE-FOAM-1"X75ft

GRIP MOLDED ROUND

BOARD ISOLAORS 17/32" SHORT

TAPE-ADHESIVE 1'X108' ST567

BUSHING-REAR ELEVAION

FLYWHEEL 1.125 10MPH FOR 2.5 ROLLERS

ACTUATOR 40LB-MAYTECH

MOTOR MCM BLK CHROME 2.5HP

HARNESS-ENCODE

CORD-POWER-90"

WIRE-JUMPER 12"-220V-KEYS SERIES

HARNESS-TELCO-HRC

HARNESS-KILL SWITCH SM9.3

HARNESS CONTROLLER 80"

DECAL-CIRCUIT BREAKER ALL

DECAL-SINCLINE REMOTE

DECAL-SPEED REMOTE

DECAL DISCONNECT-MOTOR COVER

STICKER HEART RATE ACUMEN

DECAL-10YR MOTOR WARRANTY

OVERLAY CONSOLE MS6200HR

DECAL MOTOR COVER MS4200/6200

DECAL OPERATION WEDGE CONSOLE

STICKER 2.5HP

RECT 1x2x12GAx24.5

RECT 1x1x18GAx3 PUNCHED

RECT 11/2x4x16GAx42 3/4"

RECT 1x3x16GAx165

SQ 1x1x18GAx25.44

RECT 1x2x14GAx25.44

RECT 1x3x16GAx28.44

RND 0.5x18GAx100(CUT 32PCS)

RND 1.5x16GAx19H-BAR

ROD 3/8x1 1/2"

BRKT HEART RATE REC FOR WEDGE

BRACKET-MOTOR COVER

GUIDE BELT GLAVANIZED

BRKT-UNIVERSAL

BRKT CHANNEL SUPPORTS

BRK-LOWER ELEV GUSSET

BRACKET-BASE ELEVATION

BRKT FRONT ELEV-REWORK 19-0075

BRKT FRONT ELEV REVISED

BRKT-REAR LEG COVER

BRKT MTOR SUPPORT REVISED 19-0005

BRKT-MTOR TENSION

BRKT-ELEVATION PIVOT

BRACE-CNTROLLER FRONT ELEVATION

BRKT-BELT GUIDE

BRKT-LEFT STRAIGHT U/R

BRKT RIGHT STRAIGHT U/R

BRKT FRON RLLER 2 1/2

BRKT REAR OLLER 2 1/2

7

2

1

1

2

2

2

1

2

1

1

2

2

2

2

1

2

1

1

1

1

1

1

1

1

1

1

8

1

2

1

1

2

1

1

2

1

1

1

2

QTY PART #

1 19-0074

1

1

19-0076

19-0161

20-0103

20-0104

20-0105

20-0108

21-0048

21-0049

21-0051

21-0052

21-0053

22-0058

22-0077

22-0078

22-0079

23-0103

23-0104

23-0105

24-0174

24-0175

26-0085

15-0108

16-0070

07-0027

19-0159

1

1

2

1

1

1

2

1

1

1

2

1

1

1

1

1

1

1

1

1

DESCRIPTION

BRKT-ACTUATOR MOUNTING

BRKT-CONTROLLER

PLATE CONSOLE WEDGE

PROC FRAME 17-0074

PROC RT U/R 17-0061

PROC LT U/R 17-0061

PROC BENT H-BAR 17-0080

ACTUATOR X-TB CORNERS CLIPPED

STIFFNER-NOTCHED

FRAME BRACE PUNCHED

INSIDE 90 DEGREE BEND CTRL BRKT

INSIDE CT 17-0079

ELEVATION BRKT & ROD

ACTUATOR X-TB SUB-ASSEMBY

U/R SB ASSEMBLY

DECK FRAME SUB-ASSEMBLY

FRONT EVEL ASSEMBLY-CONV

DECK FRM & REAR LEG ASSEMBLY

U/R ASSEM W/STIFFNER TUBE WEDGE

FRONT ROLLER ASSEMBLY

CONSOLE ASSEMBLY MS6200HR

INST PACKET MS6200HR

INST MANUAL MS6200

BOX ASSEMBY MS6200

ELECTRONICS-LCD-4 WIN-HOR-REV

BRK MOTOR SUPPORT REVISED 19-0005 2

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

2

1

1

1

1

1

QTY

2

1

1

Page 19

Keys Milestone 6200HR Treadmill

KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY

PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.

This Limited Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the

KEYS brand name. The warranty period on the MILESTONE 6200HR to the original purchaser is (lifetime) on the frame, (10) years on the motor, (2) years parts, and (1) year labor.

Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless accompanied by written authorization by Keys Fitness).

During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty.

To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to

Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty.

This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or

(e) as a result of service by anyone other than Keys, or an authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any

Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements for payment.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED

WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE

RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty.

PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR TREADMILL

WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA.

Thank you for your business! PLEASE MAIL WARRANTY CARD TO:

KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355

.

KEYS FITNESS TREADMILL WARRANTY REGISTRATION

FIRST

M.I.

LAST

TELEPHONE

ADDRESS

CITY

DATE OF PURCHASE

Name of store or company where purchased:

How do you plan to use the treadmill?

Walk____ Run_____ Both_____

Who will use the treadmill?

Male____ Female_____ Both_____

How many family members? _____

AGE: 15-24____ 25-34____

35-44____ 45-54____

55-64____ 65 +_____

STATE

ZIP

APT. NO.

MODEL NO.

SERIAL NO.

Where did you learn about treadmills?

TV____ Radio____ Friend____

In Store Display____ Salesperson___

Print ad/flyer____ Internet______

Why did you purchase a treadmill?

Dr.’s Orders____ Loose Weight____

In-home convenience____

Improve Cardiovascular Fitness___

Safety from outdoors____

Other __________________________

Page 20

How important are each feature:

Least Most

Unique Features

Horsepower

Warranty

Price

Look/Design

Folding Feature

Other Comments:

_______________

_______________

_______________

_______________

KEYS FITNESS respects the rights of your privacy. Our company will not sell or distribute to others the information above. This information is used to track our product quality and to contact you in the event of a product safety concern. It may be used to offer you future Keys products only through the mail. Please check here if wish not to receive any additional information on Keys products.