Lenovo 9265 Laptop User Manual

Lenovo 9265 Laptop User Manual

32LC50C

32LC50CB

32LC50CS

32LX50C

32LX50CS

37LC50DC

37LC50CB

42LB50C

42LC50C

Integrated TVs

Setup & Operation Guide for

Commercial Mode

Note: All features shown within this guide may not be available on all models.

Experienced Installer

Master TV Setup

page 6

Cloning Information

pages 7-8-9

©

Copyright 2008, LG Electronics U.S.A., Inc.

Installer Overview

This is the commercial mode setup guide only. For all other information refer to the separately-supplied TV Owner’s Manual

(Users guide).

Operating Installer Menu

To set up the controls for the TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu.

LG Installer Remote

You will need an LG Installer remote control similar to the one shown to the right. The installer remote must have a “Source” button or its equivalent. The remote shown in this manual has “INPUT”

-- this button serves the purpose of a Source button.

The TV’s clonable features need to be set up. This is a critical step.

If the Master TV display panel’s clonable features like adding channel icons or channel labels are not done properly, then the cloned TV

TVs will all have problems. Refer to the Owner’s Manual for other TV features: Video, Audio etc.

LT2002 Clone Programmer

As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each cloning task as indicated. If a procedure or step is left

Connect cable to

TV MPI Jack and follow on screen instructions

Status

Indicator

MPI

Color

• green battery ok

• red battery low

Reset

Blink pattern

• slow power on

no communications

• heartbeat power on

communications ok out or not performed correctly, then the TV setup will be wrong and cloning may not work. At each step, pay attention to assure the TV screen shows the proper message(s) when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an

Analog channel, not a digital channel.

®

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

PTC INSTALLER MENU

000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

Typical Installer Menu

INPUT

TV

INPUT

POWER

MODE

TV

DVD

VCR MULTI

PIP PIP CH - PIP CH + PIP INPUT

EZ PIC EZ SOUND SWAP INFO

EXIT

CC

MENU

RATIO

SAP

ENTER

1

4

7

VOL

TIMER

MUTE

CH PAGE

8

0

2

5

9

FLASH

BACK

3

6

P A G E 2

206-4071

Table of Contents

Use this page as a reference to find pages or sections to go to and set up the TV features.

Go to page 6 to begin the Commercial Mode Master TV setup.

1. Connect TV to RF signal source.

2. Customize TV features and set up other operational controls in the Installer’s menu.

3. Copy the Master TV setup into the clone programmer.

4. Transfer the Master TV setup from the clone programmer to identical TVs.

Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Typical Installer’s Remote Control . . . . . . . . . . . . . . . . . . 4

Remote Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . 5

Commercial Mode Setup . . . . . . . . . . . . . . . . . . . . . . . 6

Master TV Cloning Connections and Cloning Overview . . . . . 7

Cloning Learning Setup . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cloning Connections/ Teaching Setup . . . . . . . . . . . . . . . 9

Installer’s Menus . . . . . . . . . . . . 10 - 11 - 12 - 13 - 14 - 15

References

Clonable Menu Features Chart . . . . . . . . . . . . . . . . . . . . 16

Editing Channel Icons/Adding Ch Labels 2-5-4 + Menu Mode 17

Detailed Instructions For Making A Master TV . . . . . . . . . 18

Software Updating Procedure . . . . . . . . . . . . . . . . . . . 19

Camport Auto Sense Operation . . . . . . . . . . . . . . . . . . . 20

Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 22

Cloning Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . 24

Commercial Mode Check . . . . . . . . . . . . . . . . . . . . . . . . 25

RJP Mode Configuration . . . . . . . . . . . . . . . . . . . . . . . 26

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Back Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Notes

• See the Installer’s menus to set up the operational features of the TV. The Installer’s section content is intended to be used primarily by qualified electronics technicians.

• Reference is made to installer remote controls used for menu operation within the manual. The remote information is provided for reference only. The typical installer remote control shown for reference in this manual may be different than the actual remote control supplied with the TV.

• For any additional information, contact your LG representative.

Note: Design and specifications are subject to change without prior notice.

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue

Englewood Cliffs, NJ 07632

For Customer Support/Service please call:

1-888-865-3026

www.lgcommercial.com

206-4071

P A G E 3

Typical Installer Multi-Brand Remote Control

P A G E 4

INPUT

TV

INPUT

POWER

MULTI

MODE

TV

DVD

VCR

PIP PIP CH - PIP CH + PIP INPUT

EZ PIC EZ SOUND

SWAP

INFO

EXIT

CC

MENU

RATIO

SAP

ENTER

1

4

7

VOL

TIMER

MUTE

CH PAGE

8

0

2

5

9

FLASH

BACK

3

6

LG Multi-brand Remote Control

Use the MODE button to select TV and put installer remote into TV operating mode.

Notes: This remote is supplied with the TV. This typical LG multi-brand remote control is shown for reference.

See next page for typical key functions in TV mode.

Follow the instructions provided on page 10 to access the Installer menus.

AA

+

AA

+

Installing Batteries in Installer Remote Control

• Remove the battery compartment cover on the back side by pressing the arrow tab forward and lifting. Install batteries matching correct polarity as shown (+ with + and - with -).

• Install two high-quality alkaline 1.5V AA batteries. Never mix old or used batteries with new ones. Replace cover.

206-4071

Installer Remote Control Typical Key Functions

Remote Control Key Functions. To put remote into TV operating mode, select TV with the MODE key.

Notes: This remote is supplied with the TV. This typical LG multi-brand remote control is shown for reference.

Follow the instructions provided on the next page to access the Installer menus.

TV INPUT/INPUT

Select available input sources.

POWER

Turns your TV or any other programmed equipment On or Off, depending on mode.

MULTI

Selects RGB, HDMI,DVI, HDMI2 and Component

Input sources.

Adjusts picture brightness.

EZ PIC

Selects the factory preset picture appropriate for the viewing environment.

EZ SOUND

Sets the appropriate sound for the program’s content.

SWAP

Exchanges the main/sub images in

Twin picture mode.

INFO

While watching a TV program, will display program information on top of the screen. Info feature is not functional for Aux sources.

THUMBSTICK

Up/Down/Left/Right/ENTER

Use to navigate on-screen menus / adjust the system settings to your requirements.

VOLUME UP/DOWN

Increases/decreases the sound level.

TIMER

Sets the amount of time before the TV automatically turns itself Off.

MUTE

Switches the sound on or off.

CHANNEL UP/DOWN/PAGE

Selects available channels found with EZ Scan.

Moves to next available page.

NUMBER Buttons (0 - 9) DASH

Use to enter a program number or channels.

Dash for multiple channels such as 9-1, 9-2, etc.

FLASHBK

Returns to the previously viewed channel.

INPUT

TV

INPUT

POWER

MULTI

MODE

TV

DVD

VCR

PIP PIP CH - PIP CH + PIP INPUT

EZ PIC EZ SOUND

SWAP

INFO

EXIT

CC

MENU

RATIO

SAP

ENTER

1

4

7

VOL

TIMER

MUTE

CH PAGE

8

0

2

5

9

FLASH

BACK

3

6

MODE

Selects remote operating mode: TV, VCR, or DVD.

Select these other operating modes, for remote to operate external devices.

PIP

Turns Twin Picture mode on and off.

Switches video window lock/unlock in the

Listings Grid.

PIPCH- / PIPCH+

In twin picture mode, tunes to next lower/higher channel.

PIP INPUT

Selects input source for the sub picture.

VCR/DVD BUTTONS

Control some video cassette recorders or DVD players. (“RECORD” is not functional in DVD mode.) Set up for VCR recording: Once, Regularly,

Weekly, Off. (“RECORD” button only).

EXIT

Clears all on-screen displays and returns to TV viewing from any TV menu.

CC

Selects a closed caption option:

Off, CC1 ~ 4, Text1 ~ 4.

MENU

Brings up the main menu to the screen.

Enters or exits a Panel Menu in the TV Guide on-screen menu system.

RATIO

Adjusts the picture aspect ratio.

SAP

Selects MTS sound:

Mono, Stereo, and SAP in Analog mode.

Changes the audio language in DTV mode.

SAP Notes

• SAP settings are retained with power off/on for individual analog channels.

• If SAP is selected and no SAP is provided, sound will not be heard on channel.

• Each analog channel may have its own SAP setting.

• Digital channels will reset to default audio language with a power off/on.

206-4071-C

P A G E 5

Commercial Mode Setup for Master TV

This page provides an overview of the TV configuration. See the pages listed below for more specific, detailed instructions at each step; how to access and use the Installer menu etc.

Note 1: Disconnect all Aux inputs. Under certain conditions, EZ Scan (Channel search) is disabled if there is an Aux input active.

Overview: Commercial Mode Setup Procedure

1. Set Installer Menu Items

(Enter Installer Menu, see page 10 for detailed instructions.) a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER.

(This clears all installer menu items, custom settings, channel labels/icons and reloads the factory default settings.) b. Set Item 003 BAND/AFC.

- Broadcast: set to 000.

- CATV: set to 001.

- HRC: set to 002

- IRC: set to 003 c. Set item 028 CH OVERIDE to 001. This allows access to EZ Scan, Manual

Scan and Channel Edit options in the Setup Menu.

d. Set other particular installer items that affect your TV programming network. See pages 10 - 15.

e. After all required installer menu item settings have been adjusted, press

ENTER on the remote to remove Installer Menu.

2. Set Up TV Features (See TV Owners Manual)

(Audio, Lock, Time menus etc. See TV Clonable options list on page 16.)

3. Run EZ Scan

(Search for all available channels.) Go to the Setup menu and access the

EZ Scan option, follow onscreen instructions. a. Edit Channel Scan. In the Setup Menu, access the Channel Edit menu.

• Add/Delete channels manual scan menu per your system requirements.

Note: Physical channel numbers are used to indicate Virtual channels.

• Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel onscreen display. Add identifiable labels for the end user to readily know what common networks are available. In the Setup menu, select the

Channel Label option, follow instructions on the bottom of the screen.

4. Transfer TV Setup to Controller Box: 2-5-5 + Menu

After the TV channel scan has been edited and channel label icons added, enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU on the remote. This transfers the TV setup to the internal controller box.

5. Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode

Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to channel onscreen displays. (See page 17.) To remove menu press MENU.

Verify TV Setup

At this point, verify that the channel lineup, channel icons and custom labels are correct. Make sure the TV features are set per your requirements.

Set item 028 Ch Overide to 000 to lock the channel scan. After the preceding has been completed, the Master TV setup is ready to be copied to the LT2002 Clone Programmer, see next page.

PTC INSTALLER MENU

000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

TV Installer Menu

00X

003 BAND/AFC 00X

001

Set these Installer Menu Items

DIGITAL 19-3

MONO STEREO SAP

WXYZ

Custom Channel Label ‘WXYZ’ created in

2-5-4 + Menu Add Channel Label Mode

000

After TV setup has been verified, set item 028 Ch Overide back to 000.

P A G E 6

206-4071

Cloning Connections/Learning Setup

Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup

Antenna or CATV

Ferrite Core

(TDK, ZCAT

2035-0930)

Connect cable to

TV MPI Jack and follow on screen instructions

Status

Indicator

MPI

Color

• green battery ok

• red battery low

Reset

Blink pattern

• slow power on

no communications

• heartbeat power on

communications ok

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

THE TV IS VERSION

THE SW IS REVISION

XX

XX

XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

®

QuickSet II Programmer

LT2002

Warning: Do not use

LT2002 while any PPV card is installed in TV or clone programmer device will be damaged.

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA

Clone Programmer

Master TV

Notes: It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the

signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the

TV screen, see above and next page.

Before you begin cloning...

• The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.)

• Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer can store up to 3 different ‘master’ setups.)

WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable.

• Use an Installer’s remote to operate Learning and Teaching menus.

• Make sure that the batteries in the Clone programmer are fresh.

• If batteries are removed, the Clone Clock time will be lost.

• Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a compatible TV which has the clock set to the current time.

• Setting the time and transferring it to the Clone or other device is a separate procedure.

• Follow the connection diagram above to connect the Clone to a Master TV TV display panel. After learning is complete, to another identical TV TV display panel to “teach” it the master setup.

• See the Clone Troubleshooting section to resolve problems.

Turn to the next page to continue Cloning Setup.

206-4071

P A G E 7

Cloning Learning Setup

Learning the Master TV Setup

Instructions for the Clone Programmer to Learn the Master TV Setup

Use MPI Cable to Connect LT2002 Clone Programmer to

Master TV MPI Port

If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.

Learn Setup from Master TV

Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,

POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the

Memory ”Bank” you want to store the master TV’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master

TV’s setup.) Once the Clone memory bank is selected, press ON/OFF,

POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup.

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master

TV’s clock by copying the time from the Clone programmer.) The

Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I.

input capability.

After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

THE TV IS VERSION

THE SW IS REVISION

XX

XX

XX

CLONE CLOCK=

TV CLOCK=

XX:XX

XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

This menu should appear by itself after the

LT2002 is connected to the TV MPI port.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER

This menu should appear after any key is pressed on the Installer remote.

LT2002 Clone Programmer Communication Problems

• A slow flashing green light indicates there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

• If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline

AA batteries.

P A G E 8

206-4071

Cloning Connections/Teaching Setup

Teaching the Master Setup to Another TV

Connections for the LT2002 to Teach another TV the Master Setup

Antenna or CATV

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

THE TV IS VERSION

THE SW IS REVISION

XX

XX

XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Target TV

Teach Master TV’s Setup to the target TV

After learning is complete, remove the M.P.I. cable from the master TV and connect it to the target TV that you want to copy the master TV’s setup into. With “THE CLONE HAS

CONTROL OF TV” message displayed, press 2 or use either

Channel key to go to the “TEACH TO TV” option, press ON/OFF,

POWER, or ENTER. Select the LT2002 memory that the new setup is in. Press On/Off to transfer the new setup and other information to the new TV. Teaching usually takes 2-3 minutes.

After the “TEACHING COMPLETE” message is displayed, press any key to return to the Clone menu, then press ON/OFF,

POWER, or ENTER. If finished, detach M.P.I. cable from the target, newly-cloned TV.

Disconnect TV Power for 15 Seconds

Unplug the AC power cord of the newly-cloned TV from the power outlet for about 15 seconds to activate the newlycopied setup.

Ferrite Core

(TDK, ZCAT

2035-0930)

206-4071

Connect cable to

TV MPI Jack and follow on screen instructions

Status

Indicator

MPI

Reset

Color

• green battery ok

• red battery low

Blink pattern

• slow power on

no communications

• heartbeat power on

communications ok

®

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA

Clone Programmer

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER

This menu should appear after any key is pressed on the Installer remote.

TEACHING IN PROGRESS,

PLEASE WAIT

This display will appear during

Teaching function.

TEACHING COMPLETE

This display will appear after Teaching is complete.

P A G E 9

Installer Menu

Use the Installer’s Menu to set up or change operational settings.

See more detailed descriptions of the Installer menu items on the following pages...

Accessing the Installer’s Menu

Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote control. Just press MENU repeatedly until the TV seems to stop responding, then press 9,

8, 7, 6, then ENTER to access the Installer’s menu. To remove the Installer’s menu, press

ENTER again. Any changes you make will be stored in nonvolatile memory. (The menu also

disappears automatically.)

PTC INSTALLER MENU

000

022

023

028

029

030

031

032

009

010

011

015

016

017

021

034

Menu Item

000

001

002

003

004

005

007

008

The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow keys to sequence through the available menu items. Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right arrow keys. Or, enter a value directly.

Using the Installer’s Menu

Items 000 ~ 117 are immediately accessible only upon entering the Installer’s Menu.

Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages.

Installer Menu Items 000 through 117

Function

INSTALLER SEQ

POWER MANAGE

AC ON

BAND/AFC

STRT CHANNEL

CHAN LOCK

STRT VOLUME

MIN VOLUME

MAX VOLUME

MUTE DISABLE

KEY DEFEAT

SLEEP TIMER

EN TIMER

ALARM

V-CHIP

MAX BLK HRS

CAPTION LOCK

CH. OVERIDE

OLD OCV

ACK MASK

POLL RATE

TIMING PULSE

CAMPORT EN

Value Range

0 ~ 3

0 ~ 7

0 / 1

0 ~ 3

0~125, 126, 127, 255

0 / 1

0 ~ 63, 255

0 ~ 63

0 ~ 99

0 / 1

0 / 1

0 / 1

0 / 1

20 ~ 169

186 ~ 227

0 ~ 63

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0

94

207

1

0

12

0

0

1

1

0

1

63

0

1

Default Value

0

0

0

1

255

0

255

0

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

Typical Installer Menu

Brief Description of Function and Comments

Leave default set to 0.

Sets number of hours of no activity before auto shut Off.

Set to 1 to enable auto turn On at power up.

Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

Channel at turn-on (Set 255 to return to last channel before power Off).

If set to 1, cannot tune from current channel.

Sets Volume level at TV turn-on (Set 255 to retain last volume level).

Sets minimum allowable volume setting.

Sets maximum allowable volume setting.

Set to 1 to disable mute function.

Set to 1 to disable menu navigation keys on display panel.

Set to 1 to enable Sleep Timer.

Set to 1 to enable On/Off Timers.

Set to 1 to enable Alarm.

Set to 1 to enable V-Chip functions.

Sets number of V-Chip (Parental Control) blocking hours.

Set to 1 to retain caption setting at power Off.

If set to 0, limits direct access to favorite channels.

Set to 1 to change M.P.I. operation to OCV.

If set to 1, changes M.P.I. for some OCV boxes.

Selects poll rate for M.P.I.

Sets baud rate for M.P.I.

Set to 1 to enable Video 2 input.

P A G E 1 0

206-4071

Installer Menu

Installer Menu Items 035 through 118

075

078

079

080

081

082

083

084

087

Menu Item

035

038

039

040

046

047

053

069

070

071

073

Function

COMPPORT EN.

YPrPb EN.

REAR AUX EN

AUTO CAMPORT

STRT AUX SRCE

AUX STATUS

DIS. CH-TIME M.

EN. CH-T COL.

FOR. CH-TIME

BCK. CH-TIME

CH NOT AVBLE

REVERT CH

UPN MSB

UPN MSB-1

UPN MSB-2

UPN LSB

CHKSM ERROR

HANDSHK TIME

PERMANENT BLK

REAR RGB EN.

0 / 1

0 ~ 255

0 ~ 255

0 ~ 255

0 ~ 255

0 / 1

0 ~ 5

0 / 1

0, 1, 2,

17, 18

Value Range Default Value

0 / 2

0 / 1

0 / 1

0 / 1

Note 1

0 / 1

0 / 1

0 / 1

0 ~ 7

0 ~ 7

0 / 1

1

1

1

1

255

0

0

1

2

2

0

0

0

0

0

0

1

5

0

2

102

103

104

106

116

117

088

090

091

093

094

096

099

EN NOISE MUTE

KEY LOCK

YPrPb2 EN.

RJP AVAILABLE

SAP MENU EN

DEF. ASP. RATIO

BACK LIGHTING

ATSC BAND

ATSC TUNE MODE

START MINOR CH

ASP RATIO LOCK

VIDEO MUTE EN

FACT DEFAULT

0 / 1

0 / 1

0 / 2

0, 1, 2, 5, 6

0 / 1

0 ~ 5

1 ~ 100

101 ~ 200

0 ~ 4

0 / 1

0 ~ 255

0 / 1

0 / 1

0 / 1

Note 1: Dependent on item 093 RJP Available setting.

4

0

0

1

0

0

1

0

1

0

1

2

100

Brief Description of Function and Comments

Set to 0 to disable HDMI 1. Set to 1 for DTV, set to 2 for PC.

Set to 1 to enable display panel Component Video input jacks.

Set to 1 to enable display panel Video 1 input jack.

Set to 1 to automatically switch to Camport.

Sets the starting AUX source.

Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0.

Set to 1 to disable Channel-Time display.

Set to 1 to enable custom color for the Channel-Time display.

Chooses custom foreground color for the Channel-Time display.

Chooses custom background color for the Channel-Time display.

If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the TV memory channel list.

If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.

User programmable number, most significant byte.

User programmable number, most significant byte - 1.

User programmable number, most significant byte - 2.

User programmable number, least significant byte.

Enforces rigid M.P.I. checksum.

Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems.

Removes block hours setting for Parental Control and makes block permanent.

Set to 0 to disable RGB1. Set to 1 to enable for RGB DTV mode. Set to 2 to enable for RGB PC.

Set to 17 for one time auto configuration in DTV mode.

Set to 18 for one time auto configuration in PC mode.

If set to 1, mutes audio if no signal is present.

If set to 1, keyboard is locked out, IR is still functional.

Set to 0 to disable HDMI 2. Set to 1 for DTV, set to 2 for PC.

Set to 0 to disable. Set to 1, 2, 5 or 6 for HDMI or DVI mode. (See detailed descriptions)

Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu.

Sets default aspect ratio at power up. See detailed descriptions and item 106.

Sets the power saving mode by controlling the brightness of the picture.

Selects ATSC band.

Default 01 for physical channel scan. Set to 0 for Virtual Channel scan.

Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number.

To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.

Set to 0 for normal, set to 1 for Blank.

0=Normal. 1=Loads presets of all above settings.

206-4071

P A G E 1 1

Installer Menu

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Specifies entry sequence to the Installer Menu.

0 = 9876 1 = 4321

2 = 1478 3 = 3698

Generally, this feature is used in connection with START CHANNEL

(Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV will remain locked on

Channel 3.

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The POWER

MANAGE function is for saving energy. If set to 0, Power Manage is Off.

Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain On, unless there has been activity from either the control panel or remote control.

NOTE: For Items 007, 008 and 009

For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV.

To translate a TV volume level to the installer menu value, use the following formula:

002 - AC ON (AC Power Switchable)

If set to 1, allows the TV to turn On just by applying AC power.

Pressing the On button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch.

Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is

Off, and 1 is On.

NOTE: If set to 1 (On), the TV does not respond to On/Off commands from either the remote or the display control panel, and the SLEEP

TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control)

There are 4 possible settings for this option:

Installer Value = TV Value x 63

100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned On. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned Off; at turn On, the volume level will be automatically set at the previous or last level.

0 = Broadcast

2 = HRC

If some channels were not found by EZ SCAN (Auto Program), select the appropriate Band setting here and add the channels using the

Channel Edit option in the Setup Menu.

1 = CATV

3 = IRC

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial channel number when the TV is turned On. This feature is useful for an inhouse information channel, since the TV would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed when the TV was turned Off, to be the tuned to channel when the TV is turned On again. Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.

255 = Last channel

126 Map to Channel 3.

1 ~ 125 = Ch X 0 = Aux

127 Map to Channel 4.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the

VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63

— change values with ADJ Left/Right arrow. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOL-

UME is also set to 63. It may be best to set the same value on every

TV.

NOTE: The minimum volume level cannot have a value setting higher than the MAX VOLUME level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the

VOLUME (VOL) Up/Down controls. In this way, for example, someone can not set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0.

Change values with ADJ Left/Right arrow keys. It may be best to set the same value on every TV.

NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously).

005 - CHAN LOCK (Channel Lock)

CHAN LOCK is ideal if the system must always be on the same channel.

Changing channels with Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

P A G E 1 2

206-4071

Installer Menu

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, key defeat prevents the end user from accessing the onscreen menus with the display front panel—MENU, SELECT, and Left /

Right arrow keys do not function. If set to 0, those keys do function.

NOTE: The menus can always be accessed by pressing MENU on the remote.

021 - V-CHIP (Parental Control) *

Set to 1 to activate V-Chip (Parental Control); have it available to end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn V-Chip feature Off, not available to user; no programming restrictions can be set.

031 - POLL RATE

M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at default setting unless changed by Pay-Per-View provider. Step size of

16 ms.

015 - SLEEP TIMER

If set to 1, the SLEEP TIMER feature may be used. If set to 0, the

Sleep Timer is not available.

017 - ALARM *

Gives the installer the option of making the Alarm function available to the end user. If set to 1, Alarm function is available to end user.

Set to 0 to disable the Alarm function.

NOTE: Clock must be set before the Alarm function will work.

032 - TIMING PULSE

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS.

016 - EN TIMER (Enable On/Off Timers) *

If set to 1, Timer function is available to user and enabled continuously. Set to 0 to disable On/Off Timers. (Clock must be set in order to use Timers.)

034 - CAMPORT EN. (Camera Port Enable)

Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.

NOTE: S-Video overrides Video jack.

035 - COMPPORT EN. (Computer Port Enable)

Enable/disables display panel HDMI1 input jack. Set to 0 to disable, set to 1 to enable DTV mode, set to 2 for PC mode.

NOTE: The setting above is ignored if Installer item 093 RJP AVAIL-

ABLE, is set to 1.

038 - YPrPb EN. (Rear Component Video Enable)

Set to 1 to enable display panel rear Component Video input jacks.

Set to 0 to disable display panel rear Component Video input jacks.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear AUX (Video 1) input.

Set to 0 to disable display panel rear AUX (Video 1) input.

Note: S-Video overrides Video.

022 - MAX BLK HRS (Maximum Block Hours) *

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

023 - CAPTION LOCK

Set to 1 to restore previous caption On/Off state after turn Off. If set to 0, captions are always Off at turn On.

040 - AUTO CAMPORT

Set to 1 to automatically switch to Camport when equipment is connected to front Video input.

Set to 0 to disable front Video automatic source selection.

NOTE: If set to 1, 093 RJP Available is automatically set to 0.

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either Channel up/down or by direct keypad entry. If set to 0, only those channels that are entered for scanning can be selected.

029 - OLD OCV (On Command Video TM )

Set to 1 for operation with systems from On Command Corporation.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting AUX source. At power up, TV will tune to starting Aux source if item 004 Start Channel is set to 0.

If item 093 RJP Available is set to 0 and item

040 Auto Camport is set to 0:

1 = Video 1

2 = Video 2

4 = RGB

5 = HDMI 2

255 = Last Aux

3 = HDMI 1 6 = Component

030 - ACK MASK

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. When set to 1, changes M.P.I. for some OCV boxes.

* Only affects Function Menu if enabled by some PPV providers.

If item 093 RJP Available is set at 1:

2 = Video 2 5 = HDMI 2

If item 040 Auto Camport is set to 1:

1 = Video 1

3 = HDMI 1

4 = RGB

5 = HDMI 2

6 = Component

6 = Component

206-4071-D

P A G E 1 3

Installer Menu

Detailed Descriptions of Installer Menu Items

047 - AUX STATUS

Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change.

Controls M.P.I. status channel response for AUX inputs.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 readable by M.P.I.

command. Not linked to serial number.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display, Channel-Time display will not appear.

Set to 0 to enable the Channel-Time display.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable by M.P.I.

command. Not linked to serial number.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display.

Set to 0 to disable custom color for the Channel-Time display.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid M.P.I. checksum validation.

Set to 1 for validation.

Set to 0 to disable (does not check checksum on M.P.I. async port).

SPI is always checked.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)

Set according to Color Chart.

0 = Black

1 = Blue

3 = Cyan

4 = Red

6 = Yellow

7 = White

2 = Green 5 = Violet

NOTE: If foreground and background color are the same, menu background is transparent.

071 - BCK. CH-TIME (Channel-Time Display Background Color)

Set according to Color Chart.

0 = Black 3 = Cyan

1 = Blue

2 = Green

4 = Red

5 = Violet

6 = Yellow

7 = White

NOTE: If foreground and background color are the same, menu background is transparent.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT AVAIL-

ABLE” message is displayed when directly accessing a channel not in the channel scan list available in memory.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec, thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time]).

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function.

Set to 1 to install Parental Control restrictions permanently.

Set to 0 for user-specified hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV.

Set to 0 to disable RGB input.

Set to 1 to enable RGB in DTV mode.

Set to 2 to enable RGB in PC mode.

If set to 1 or 2, auto configuration is performed when RGB is selected or input change is detected.

Set to 17 to enable RGB in DTV mode.

Set to 18 to enable RGB in PC mode.

If set to 17 or 18, auto configuration is done one time after a power cycle.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable by M.P.I.

command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 readable by M.P.I.

command. Not linked to serial number.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes if no signal is present.

090 - KEY LOCK

If set to 1, display panel keyboard is locked out, not available to end user. IR receiver remains functional.

091 - YPrPb2 EN. (HDMI2 Enable)

Set to 0 to disable display panel HDMI2 input.

Set to 1 to enable DTV mode. Set to 2 to enable PC mode.

P A G E 1 4

206-4071

Installer Menu

093 - RJP AVAILABLE (Remote Jack Pack Available)

0 = Remote jack pack is not available or disabled.

1 = Series 100 RJP, HDMI Mode

Enables RJP when an HDMI cable is inserted into RJP. Video is from

HDMI. Audio stream is expected from HDMI source. If no audio is present, no audio will be heard.

2 = Series 100 RJP, DVI Mode

Enables RJP when an HDMI cable is inserted into RJP. Video is from

HDMI however, Audio is from selected audio source, based on the RJP’s audio hierarchical priority.

5 = Series 200 RJP, HDMI Mode

Enables RJP when an HDMI cable is inserted into RJP. VIdeo is from

HDMI. Audio stream is expected from HDMI source. If no audio is present, no audio will be heard.

6 = Series 200 RJP, DVI Mode

Enables RJP when an HDMI cable is inserted into RJP. Video is from

HDMI however, Audio is from selected audio source, based on the RJP’s audio hierarchical priority.

Notes:

• See Reference section, RJP Mode Configuration page.

• If set to 1, 2, 5 or 6, item 040 Auto Camport is automatically set to 0.

Settings 1, 2, 5 and 6 allow the lodge staff to customize each TV’s RJP setup based on customer requirements.

099 - BACK LIGHTING

Sets the TV screen brightness at power up, see settings below.

Default setting is 100 power saving mode is disabled.

1 - 100 Static Backlighting.

(1 = Dimmest picture, 100 = Brightest picture.)

101 - 200 Dynamic Backlighting.

(101 = Dimmest picture, 200 = Brightest picture.) TV automatically controls backlighting depending upon the picture level of the current program.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:

0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.

103 - ATSC TUNE MODE

Sets ATSC tuning mode: Default set to 1 for Physical channel scan.

Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets XX-XX minor starting channel at power up: 0=NTSC. If not 0, number selected is the Minor start channel number.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power Off.

Set to 0 to retain default aspect ratio with power Off. See item 96

Default Aspect Ratio above.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function menu, if Function menu is available.

Set to 0 to disable SAP feature on Function menu, if Function menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up, see settings below.

116 - VIDEO MUTE EN (Video Mute Enable)

Set to 0 for normal.

Set to 1 for blank.

117 - FACT DEFAULT (Factory Default)

Set to 0 for normal.

Set to 1 to load presets to all of the previous item settings.

WARNING: Setting this to 1 will reload the factory defaults and clear the channel list including erasing any assigned

Channel Icons and Custom Channel Labels.

Set to 0 “Set By System”.

Set to 1 for 4:3.

Set to 2 for 16:9 (Factory Default).

Set to 3 for Horizon

Set to 4 for Zoom 1

Set to 5 for Zoom 2

206-4071

P A G E 1 5

Reference: Clonable Menu Features

Menu /Sub Menu Features

Setup

SET ID

Audio

Audio Language

EZ SoundRite

EZ sound

Balance

Treble

Bass

Front Surround

TV Speaker

BBE

Time

Auto Clock

Auto Off

Clonable Menu Features

Option

Aspect Ratio

Caption

Caption Mode

DTV Captions Style - Style

DTV Captions Style - Size

DTV Captions Style - Font

DTV Captions Style - Text Color

DTV Captions Style - Text Opacity

DTV Captions Style - BG Color

DTV Captions Style - BG Opacity

DTV Captions Style - Edge Type

DTV Captions Style - Edge Color

Language

Cinema

ISM Method

Low Power

Lock

Movie Rating

TV Rating – Children Age

TV Rating – Children Fantasy

Violence

TV Rating – General Age

TV Rating – General Dialogue

TV Rating – General Language

TV Rating – General Sex

TV Rating – General Violence

Note: Video Menu and other feature settings are not clonable on all TVs. End user has access to EZ

Picture, EZ Sound and Ratio on user remote control.

P A G E 1 6

206-4071

Reference: Procedures for adding Channel Label Icons/Custom Channel Labels

(2-5-4 + MENU Mode)

Adding Channel Icons and Labels in the 2-5-4 + Menu Mode

Editing/Adding Channel ICONs and/or Labels

If there is no pre-assigned ICON, you can make a custom channel label of up to 7 characters to help in identifying the channel or network. At your option, channel labels can also be added in addition to a pre-assigned ICON. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.

(Icon)

Editing and adding the labels can only be done if there are channels entered into the TV’s channel map either by using the method described in item 6 (page 18), by cloning or by the use of the master remote control from the PPV provider.

Note: A blank letter space is available between ‘Z’ and ‘!’.

XYZ

XYZ

1 2 3 4 5 6 7

XYZ

NETWORK

(Label)

To Do Channel Editing/Labeling, proceed as follows

1. Enter TV Installer menu.

2. Once the installer menu appears, press ‘2’, ‘5’, ‘4’,

‘MENU’. This enters the channel label editing mode.

Add your channel icons and channel labels in this menu, see below. (You can do this more than once.)

3. To exit the menu when done press “MENU”.

Changing a Channel’s ICON on

Master TV

1. With Channel Up/Down, select the channel you want to change the

Icon for.

2. With the Right or Left ADJ arrow, select the letter ‘I’ on the channel

ID display.

3. With the Up or Down arrow, select the desired ICON you want to appear to identify the channel. (If you know the ICON number, enter the number followed by Enter /

Select.)

4. Proceed with Changing/Adding

Labels or go to the next channel.

Changing/Adding Channel Labels on Master TV

1. Channel Up/Down to select the desired channel.

2. Press the Right or Left ADJ arrow repeatedly until the numbers 1 to 7 show up. The number shows the position of the character that can be changed. Number 1 is the first character, number 2 the second character and so on.

3. With the Up or Down arrow, select the desired character.

4. Proceed to the next number position or use Channel Up/Down to go to the next channel.

Changing Source Labels on

Master TV

1. Press “INPUT” to select the desired

Aux input source; Video 1, Component,

S-Video etc.

2. Press the Right or Left arrow repeatedly until the numbers 0 to 9 shows up.

The number shows the position of the character that can be changed.

3. Use the Up or Down arrows to select the desired character.

4. Press “INPUT” for the next Aux source or proceed with Changing Icon or

Changing/Adding Labels.

Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu

• CHANNEL Up/Down - Tunes in the next channel in scan.

• Left/Right Arrows - Select the item to change. If “I” is shown, the ICON can be changed. If a number is shown, it indicates the position of the character that can be changed.

• Up/Down Arrows - Select the ICON or the character to be displayed.

• 0 – 9 - Use to enter the index number of the ICON, if known.

• ENTER/SELECT - Changes the ICON after the number has been entered.

• INPUT - Changes the Aux input label. (“Source” on the remote shown in this manual is INPUT.)

• MENU - Exits the editing process.

206-4071-C

P A G E 1 7

Reference: Detailed Information For Making A Master TV

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...

To set up a master TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu, before attempting to clone the TV Master TV setup.

You will also need an LG Installer remote control similar to the one shown in the front of this manual. The installer remote must have a “Source” button or its equivalent. The remote shown in this manual has a “INPUT” button -- this button serves the purpose of a Source button.

Finally, the TV’s clonable features need to be set up. This is a critical step. If the Master TV display panel’s clonable features like adding channel icons or channel labels, digital font options etc., are not correctly added, then the cloned TVs will all have problems.

As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel.

Making a Master TV

Detailed Instructions

The following describes the procedure for preparing a Master TV for cloning and the procedure for adding Channel Icons and/or

Labels.

Note 1: Disconnect all Aux inputs. Under certain conditions, EZ

Channel Scan is disabled if there is an Aux input active.

Note 2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu.

1. Enter the TV installer menu. a. Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT, set it to 1 and press “ENTER”. The value will change back to 0 after the TV’s internal controller has been restored to factory default condition. This step will ensure that the TV channel memory will be the active channel list. Check the Status LED. If it is blinking rapidly then the TV channel map is in use. b. Within the Installer menu, set the Installer menu items to the configuration required of your institution. c. It is important to set the tuning band at this time, see

Installer menu item 03 BAND/AFC. d. Set Installer menu item 28 – CH OVERIDE to 001 to allow access to the EZ Channel Scan and Surf List/Ch. Edit features in the SETUP Menu. Exit the Installer menu.

2. Access the Master TV menus and set the clonable options on the menus to the desired configuration. Refer to the

Clonable Menu Features Chart on page 16 in this manual.

3. Run EZ Channel Scan to find analog and digital channels.

4. Enter the Channel Edit menu and edit the channel lineup to include the Free-To-Guest Channels only.

5. Assign ICONs to the channels using the Channel Label Menu.

Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add

Channel ICONS or labels for channels without Icons.

6. Transfer the TV setup: Enter the TV installer menu. Press ‘2’,

‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the

TV. Once the transfer is complete, the system will exit the

Installer menu. Check the Status LED inside the TV. It should be blinking slowly (1 blink per second).

7. Edit/Add Channel ICONs and Channel Labels as needed.

Enter Installer menu. With menu displayed, press 2-5-4 +

MENU. See page 17 for detailed instructions:

- Editing/Adding Channel ICON and Labels on Master TV

- Changing a Channel’s ICON on Master TV

- Changing/Adding Channel Labels on Master TV

- Changing Source Labels on Master TV

8. Verify Master TV setup and feature configuration:

• Did you add Channel ICONS?

• Did you add Channel Labels?

• Did you add Source Labels?

• Did you adjust all TV menu options as required?

After verifying master setup, enter the TV Installer menu and set Installer menu item 28 CH OVERIDE to 000. Press ENTER to remove and exit the Installer menu.

P A G E 1 8

206-4071

Reference: Checking Software Version

Procedure for Checking Software Version

The software version of the TV may be checked by accessing the INSTALLER MENU. To do this, press the MENU button repeatedly until the menu display ceases to respond to MENU key presses.

Then, press "9", "8", "7", "6", "ENTER/SELECT".

PTC INSTALLER MENU

000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000

CPU V3.06.00

Typical Installer Menu

206-4071

P A G E 1 9

TV Camport Auto Sense Operation

The CAMPORT Auto Sense function is enabled when:

1. Installer Menu Item 34, CAMPORT EN is set to 1 AND

2. Installer Menu Item 40, AUTO CAMPORT is enabled (1).

Selectable= Can be accessed with INPUT key, direct access, etc.

Auto Sense= Switches to this input when connector is inserted.

The camport (Front Video) has the highest priority and will override any commands including tuning to the Start Channel.

CAMPORT (Front Video) Functionality Control

Item 34 Item 40

CAMPORT EN AUTO CAMPORT

0 0

0 1

1

1

0

1

Front Video

Operation

Disabled

Disabled

Selectable

Auto Sense

CAMPORT Operation (Stand-Alone)

When Camport Auto Sense is enabled as above, the TV’s source will switch to the front video whenever a plug is inserted into any of the front panel video inputs (either composite Video or

S-Video).

When the plug is removed, the TV will switch back to the previous channel or input source that the TV was using before the plug was inserted. However, if any direct access to an RF channel or Aux channel is requested while the camport is active, then, when the camport plug is removed, the TV will switch to the last requested channel. Source changes using any Source

Keys (INPUT) are ignored. Channel Up/Channel Down and

Flashback Commands are not direct access tuning commands and they are also ignored.

Previous State Operation

Before Inserting While CAMPORT

CAMPORT

Aux or RF Channel

Is Active

None

Direct Access Aux or RF Channel

Aux or RF Channel Ch Up/Down,

Flashback and TV/AV Keys

State

Upon Removal

Of CAMPORT

Previous Aux or RF Channel

Last Requested

RF or Aux Channel

Previous Aux or RF Channel

CAMPORT Operation (PPV)

The operation will be similar to that of the Stand-Alone mode.

However, the PPV providers may send different commands to the TV for the same user commands. For instance, some providers will always send a direct tune command when it receives a channel up/down or a flashback command while other PPV providers will just send a key command.

Previous State Operation

Before Inserting While CAMPORT

CAMPORT

Aux or RF Channel

Is Active

None

Aux or RF Channel

Aux or RF Channel

Direct Access

Ch Up/Down,

Flashback and TV/AV Keys

State

Upon Removal

Of CAMPORT

Previous Aux or RF Channel

Last Requested RF or Aux Channel

Last Requested

Channel if PPV translates it to direct access tuning command. Otherwise, goes to Previous Aux or RF Channel

P A G E 2 0

206-4071

TV Aux Input Configuration / Troubleshooting

Troubleshooting

Some quick and easy tips to resolving problems

Possible Cause(s) Symptoms

Software Problems

Cannot direct enter channel number or

“No Signal” appears.

Channel not included in channel scan in TV controller.

Possible Solution(s) See Page(s)

After 2-5-5 + MENU, only channels included in TV controller will appear.

6

If channel is available it can be added to channel scan. If it is not available, the ‘No Signal’ message appears on the TV screen.

206-4071

P A G E 2 1

Troubleshooting

Some quick and easy tips to resolving problems

Possible Cause(s) Symptoms

Power

No Power.

See troubleshooting flow chart.

Possible Solution(s) See Page(s)

24

Display Panel Picture

No Picture.

• Display panel is turned off.

• Antenna/Cable not connected.

• Connections incorrect.

• M.P.I. not connected.

• Encrypted program.

• Wrong tuning band.

-Turn TV on.

-Power failure?

-Connect Antenna/Cable signal to TV.

-Check connections on TV.

-If applicable, connect M.P.I. cable to M.P.I. device.

-Try another channel.

-Adjust Installer menu settings.

(See Owners manual)

(See Owners manual)

10 ~ 15

Erratic Operation

Installer menu setup.

• Wrong Installer menu settings.

-Adjust Installer menu settings as required.

Remote Control

Remote doesn’t work.

• Remote not in TV mode.

• Not aimed at IR remote sensor.

• Remote too far from IR sensor.

-Use Mode key to select TV; puts remote into TV mode.

-Point remote at TV’s IR receiver on TV.

-Move remote closer to TV’s IR receiver or darken room.

• IR path to TV’s receiver obstructed. -Remove obstructions.

• Weak batteries.

-Replace batteries.

• Wrong battery polarity.

• Too much light in room.

• Wrong Installer remote control.

-Check that “+” and “-” match in battery compartment.

-Dim room light.

-Requires compatible Installer remote, contact your LG dealer.

10 ~ 15

5

4

5

2

Picture Reception

Normal picture, poor or no sound.

• Audio muted.

• Broadcast problem.

-Press MUTE or use Volume Up key to increase sound level.

-Try a different channel.

Note: For other problems not caused by the TV, refer to other devices’ operating guide.

5

5

P A G E 2 2

206-4071

Reference: Cloning Procedure Troubleshooting

Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer will be damaged.

Reset Clone After Static Shock

After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked ”RESET” to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time.

Note

The LT2002 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the

221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.)

Clone Programmer Troubleshooting

Problem Possible Cause(s)

Clone Programmer

Clone copies Setup in less than 30 seconds

Remote does not operate clone.

LED does not blink.

• Not enough time to copy entire TV setup.

• Wrong Installer remote.

• M.P.I. cord not connected.

• TV not turned on.

• Weak batteries.

• Weak signal.

Clone menu hard to read.

No time set.

Clone not working.

Clone Scans Channels more than once.

• Time not available.

• Clone programmer problem.

• Clone should only scan channels once.

Possible Solution(s)

- Press Reset on clone programmer, redo teach/learn.

(Teach/Learn should take a minimum of 1 minute.)

- Only use an LG Installer remote to operate clone programmer with TV.

- Connect M.P.I. cord properly, assure good connection.

- TV must be powered On for clone to work.

- Install 4 fresh AA high-quality alkaline batteries.

- Connect TV to a reliable Analog channel signal source.

- Set time on a TV, copy time to Clone Programmer.

- Try a different LT2002 Clone programmer.

- Reset Clone Programmer.

- Retry cloning again.

Master and Other TVs

Cloning did not work.

• Procedure interrupted.

• Different TV models.

• Step(s) omitted or not performed.

Clone time disappeared.

• Batteries were removed.

- Wait until procedure complete message is displayed.

- Cloning is only possible with identical model TVs.

- Reread pages 7-8-9 to be sure all tasks were performed.

206-4071

- Batteries must remain installed to retain time settings.

New Setup not present.

• TV not reset.

- Disconnect newly-cloned unit from power for 5 seconds.

• After cloning operations are complete, just unplug the LT2002 from the TV.

• If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels.

P A G E 2 3

Troubleshooting Flow Chart

Controller

Quick

Check

Is

'STATUS'

LED on

Analog Board

Blinking

?

Yes

No

Is

TV

Connected to

AC Power

?

No

Yes

Bad

TV

Plug into AC

Power Outlet

Is

Red LED on TV

Lit

?

Yes

No

Cycle the power by removing and re-connecting the AC power cord. Observe the

'POWER' LED and TV screen as soon as AC power is re-applied.

1. Bad Analog Board.

2. Bad Digital Board.

Did

Analog

Board 'POWER'

LED Turn On

Momentarily

?

No

Yes

Bad

TV

Did TV

Turn On

Momentarily

?

Yes

No

Check to see if TV is in Commercial Mode.

See Commercial Mode

Check chart.

Press 'POWER' or 'ON/OFF' key on TV

Did

TV Turn

On

?

Yes

No

Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or

'MUTE' key on Installer

Remote

1. Bad TV

Did

TV

Respond

?

No

Yes

1. Bad TV

2. Go to Remote

Control Checklist page 5

Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or 'MUTE' key on

User-Supplied Remote

Did

TV

Respond

?

Yes

No

1. Bad PPV Card

2. Go to Remote

Control Checklist page 5

End

P A G E 2 4

206-4071

Commercial Mode Check

206-4071

Press the "On/Off" key on the front panel.

The On/Off key is always operational.

Did you get a response

?

No

Bad TV

Yes

Leave the

TV set On

Go to Installer menu by pressing "MENU" until the TV stops responding.

Did

TV stop responding or continue to respond

?

Continued to respond

Stopped responding

TV is in

Commercial

Mode.

TV is not in Commercial Mode

Call Technical Support for

Assistance

P A G E 2 5

Reference: RJP Mode Configuration

P A G E 2 6

206-4071

Glossary of Terms

A list of definitions for some of the words found in this guide

75 OHM RF CABLE

The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the

Antenna/Cable threaded jack on the back of the TV.

300 TO 75 OHM ADAPTER

A small device that connects a twowire 300 ohm antenna to a 75 ohm RF jack.

They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.

ANALOG TELEVISION

Standard television broadcasting format in

4:3 picture aspect ratio.

A/V CABLES

Audio/Video cables. Three cables bunched together—right audio (red), left audio

(white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE

Any device that produces video or sound

(VCR, DVD, cable box, or television).

DIGITAL TELEVISION

High-resolution, cinema-quality television signals transmitted digitally.

DVI

Digital Video Interface

Accommodates analog and digital interfaces with a single connector.

PHYSICAL CHANNEL NUMBER

See Note 1.

COMPOSITE VIDEO

Typical video jack, uses one wire for transporting three-color video signals.

RGB (Red, Green, Blue)

Connection input or output port available for producing a video image using three separate colors: Red, Green, and Blue.

COMPONENT VIDEO

Uses three wires for transporting three-color video signals. The end result is usually better video quality.

RS-232

Serial communication port through which the display panel is controlled.

DELETED

Lets you remove channels from the list that the end user can scroll through using CH

(Channel) Up/Down.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is another, separate audio channel available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French.

HDMI

High-definition multi-media interface.

OUTPUT

Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device.

SIGNAL

Picture and sound traveling through a cable, or over the air, to the TV.

HDTV

High-definition television. Refers to television signals that have higher resolution than ordinary analog TV signals.

STEREO SOUND

Stereo (Stereophonic) sound refers to audio that’s divided into right and left sides.

AMPLIFIER

An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other Audio/Video device.

HDSTB

High-definition set top box. Refers to a tuner device that receives high-definition television signals which have higher resolution than ordinary analog TV signals.

TUNER

Device that picks up the broadcast signal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

See Note 1.

ANTENNA

The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna.

CABLE

Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals.

CATV

Programming provided by a cable service.

INPUT

Refers to the input jack that receives a signal from a TV, VCR, DVD Player or other

Audio/Video device.

JACK

An input or output connector on the back of a TV, VCR, DVD Player or other

Audio/Video device.

MONO SOUND

Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

XDS

Extended Data Service: Additional program information included on the signal provided at the discretion of the broadcaster.

Note 1

Refer to www.atsc.org for further information.

206-4071

P A G E 2 7

For Customer Support/Service Please call:

1-888-865-3026

www.lgcommercial.com

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue

Englewood Cliffs, NJ 07632

© Copyright 2008, LG Electronics U.S.A., Inc.

206-4100

Issue*

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project