LG Electronics 26LQ630H CRT Television User Manual

LG Electronics 26LQ630H CRT Television User Manual

22LQ630H 26LQ630H 32LQ630H

42CQ610H

Hospital TVs

Commercial Mode Setup Guide

Note: Selected features shown within this guide may not be available on all models.

EXPERIENCED INSTALLER

Express Script Installer Menu Wizard pages 11 – 14

Custom Master TV Setup pages 15 – 18

Cloning Information pages 32 – 40

FTG Mode of Operation pages 41 – 52

© Copyright 2012, LG Electronics U.S.A., Inc.

P/N: 206-4207 (Rev C)

For Customer Support/Service, please call:

1-888-865-3026

The latest product information and documentation is available online at:

www.LGsolutions.com/products

MODEL and SERIAL NUMBER

The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:

Model No._________________ Serial No._______________

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electrical

Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc.

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

© Copyright 2012, LG Electronics U.S.A., Inc.

206-4207

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus.

When a cart is used, use caution when moving the cart/ apparatus combination in order to avoid injury from tip-over.

PORTABLE CART WARNING

13. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Never touch this apparatus or antenna during a thunder or lighting storm.

15. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.

16. Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.

17. Power Cord

Caution: It is recommended that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page in the Owner’s Manual to be certain.

Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Do not use a damaged or loose power cord. Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

18. Overloading

Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in fire or electric shock.

19. Outdoor Use/Wet Location

Warning: To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids.

Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).

20. Grounding

Ensure that you connect the earth ground wire to prevent possible electric shock (i.e., a TV with a three-prong grounded

AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.

21. Disconnect Device

The mains plug is the disconnecting device. The plug must remain readily operable.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.

(Continued on next page)

206-4207

3

IMPORTANT SAFETY INSTRUCTIONS

4

(Continued from previous page)

22. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to NEC, ANSI/NFPA 70

Ground Clamp

Electric Service

Equipment

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

23. Cleaning

When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.

24. Transporting Product

Make sure the TV is turned Off and unplugged and that all cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV during transport.

25. Ventilation

Install the TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the TV with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.

26. Do not touch the ventilation openings, as they may become hot while the TV is operating.

27. If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord, and contact an authorized service center.

28. Do not press against the front panel of the TV with your hand or a sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.

29. Keep the product away from direct sunlight.

30. Dot Defect

The LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you are viewing the

TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

31. Generated Sound

“Cracking”: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

32. For LCD TV

If the TV feels cold to the touch, there may be a small “flicker” when it is turned On. This is normal; there is nothing wrong with the TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

206-4207

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . . 6 – 8

Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pass-through Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FTG Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote Management in FTG Mode . . . . . . . . . . . . . . . . . 8

Pro:Centric Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pro:Centric TV Interactive Menu Features . . . . . . . . . . . . 9

Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installer Remote Control Typical Key Functions . . . . . . . . 10

Express Script Installer Menu Wizard . . . . . . . . . . 11 – 14

Custom Master TV Setup. . . . . . . . . . . . . . . . . . . . . 15 – 18

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cloning Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Clonable TV Setup Menu Features . . . . . . . . . . . . . . . . 15

Custom Master TV Setup Procedure . . . . . . . . . . . . . . . 16

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 – 26

Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . . . 19

Using the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . 19

Exiting the Installer Menu and Activating Updates . . . . . 19

Channel Icons / Custom Text Labels

(2-5-4 + MENU Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Channel Banks Setup. . . . . . . . . . . . . . . . . . . . . . . . . . 28 – 30

Channel Banks Worksheet. . . . . . . . . . . . . . . . . . . . . . . . . 31

Cloning Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

USB Cloning Procedures. . . . . . . . . . . . . . . . . . . . . . 33 – 36

Learning / Teaching a Master TV Setup using

a USB Memory Device / .tlx File. . . . . . . . . . . . . . . . . . . 33

Learning / Teaching a Master TV Setup using

a USB Memory Device / .tll File . . . . . . . . . . . . . . . . . . . .35

Clone Programmer Cloning Procedures . . . . . . . . . 37 – 40

Learning / Teaching a Master TV Setup using

a TLL-1100A Clone Programmer . . . . . . . . . . . . . . . . . . 37

Learning / Teaching a Master TV Setup using

an LT2002 Clone Programmer . . . . . . . . . . . . . . . . . . . . 39

FTG Mode of Operation Overview . . . . . . . . . . . . . . 41 – 42

FTG Mode via CPU or EBL . . . . . . . . . . . . . . . . . . . . . . 41

Determining the TV Operating Mode . . . . . . . . . . . . . . . 42

FTG Mode via CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 – 47

Creating an FTG Configuration File using the

FTG File Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Teaching FTG Configuration to a TV . . . . . . . . . . . . . . . 45

Learning an FTG Configuration File from a TV . . . . . . . 46

Optional Manual Configuration / TV Setup . . . . . . . . . . . 47

FTG Mode via EBL (Local Configuration) . . . . . . . . . . . 48

FTG File Manager Utilities Overview . . . . . . . . . . . . . . 49 – 52

FTG File Manager Main Screen . . . . . . . . . . . . . . . . . . . 49

FTG Channel Map Configuration Utility . . . . . . . . . . . . . 50

FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . . . 51

FTG Installer Menu Configuration Utility. . . . . . . . . . . . . 52

References

Upgrading TV/PTC Software using a USB Memory

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Downloading a Splash Screen using a USB Memory

Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Power Consumption Settings. . . . . . . . . . . . . . . . . . . . . . . 55

TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . 56

b-LAN Setup & Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 57

LQ630H/CQ610H Hospital Operations . . . . . . . . . . . . 58 – 59

Resetting Factory Defaults on the TV(s) . . . . . . . . . . . . . . 60

TV Zone Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

22LQ630H Rear and Side Jack Panels . . . . . . . . . . . . . . . 62

26/32LQ630H Rear and Side Jack Panels . . . . . . . . . . . . 63

42CQ610H Rear and Side Jack Panels. . . . . . . . . . . . . . . 64

Pillow Speaker Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

USB Media Navigation using Pro:Centric Pillow Speaker . . 66

VESA Standard TV Mounts . . . . . . . . . . . . . . . . . . . . . . . . 67

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 – 72

General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 68

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . . 69

Commercial Mode Check / FTG Operation

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Clone Programmer Troubleshooting. . . . . . . . . . . . . . . . 71

Channel Banks Setup Troubleshooting . . . . . . . . . . . . . 72

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Document Revision History / Notes . . . . . . . . . . . . . . . . . . 74

Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Notes

Installer Menu content is intended for use primarily by qualified TV electronics technicians.

Refer to the Owner’s Manual for additional information on TV installation, features, specifications, maintenance, and safety instructions.

Design and specifications subject to change without prior notice.

206-4207

5

Commercial Mode Overview

This document describes how to set up LQ630H and CQ610H TVs for Commercial Mode operation.

LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider).

Each of these TV models is capable of Free-To-Guest (FTG) Mode operation via the TV CPU. Alternatively, the EBL module can be configured either for Pass-through Mode (default) or FTG Mode. When neither the

CPU nor EBL is in FTG Mode, these TV models also allow external control via the TV’s MPI port.

Setup Checklist

Note: This document provides information specific to Commercial Mode operation. Refer to the Owner’s

Manual for detailed information on TV installation and hardware and cable connections.

Installation

__ Unpack TV and all accessories.

__ Install batteries in the Installer Remote.

__ Install TV on VESA mount or stand.

Note: It may be advisable to make all cable connections before installing on VESA mount or stand, as appropriate.

Cable Connections

__ Make all rear jack panel and MPI card slot connections, as appropriate.

Commercial Mode Setup

__ Complete appropriate procedures as described in this document for Commercial Mode operation.

Hardware Connections

__ Install any additional hardware as appropriate to your institution, LAN, etc.

Pass-through Mode

This mode allows you to configure stand-alone TVs and/or create a Master TV Setup for cloning purposes for TVs that are to remain in Pass-through Mode. This mode also allows external control via the GAME

CONTROL/MPI port on the TV rear jack panel. There are two methods for configuring stand-alone TVs in Pass-through Mode: either using the Express Script Installer Menu Wizard or the Custom Master TV

Setup procedure as described in this document.

Express Script Installer Menu Wizard

The Express Script Installer Menu Wizard guides you through the process of setting up the TVs, limiting the customization of TV features and Installer Menu items to those that are essential to most hospital TV viewing applications. The Express Script Installer Menu Wizard is described in detail on pages 11 to 14.

Note: While the Express Script Installer Menu Wizard enables you to set up TVs in lieu of cloning, you can also use an Express Script TV Setup for cloning purposes, if desired. However, note that TV setup menu customization via the Express Script Installer Menu Wizard is limited to Channel Menu options.

Custom Master TV Setup

Unlike the guided process above, the Custom Master TV Setup procedure enables you to create a customized Master TV Setup for cloning purposes. Configure Installer Menu items as required for TV operation and set up TV features (Channel, Picture, Audio, etc.). The Custom Master TV Setup procedure is described in detail on pages 15 to 18.

6

206-4207

Commercial Mode Overview (Cont.)

Installer Menu

To create a customized Master TV Setup, you will need to know how to enter the commercial controller (PTC)

Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the

Installer Menu and how to make and save changes.

Refer to pages 19 to 26 for information on accessing the

Installer Menu and for detailed descriptions of the

Installer Menu items.

TV Setup Menus

On-screen setup menus control the features of the TV.

Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user. Refer to the Owner’s Manual for detailed information on the TV setup menus.

Cloning

Cloning refers to the process of capturing a Master TV

Setup and transferring it to a Target TV (both TVs must be in Pass-through Mode). The Master TV’s clonable setup menu features should be configured as part of the

Master TV Setup. If there are features in the Master

TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the

Target TVs. Refer to pages 32 to 40 for detailed information on cloning requirements and procedures.

Note: If desired, an Express Script TV Setup also may be used for cloning purposes.

LOCK

xxLQ630H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ 000

UPN 000-000-000-000

PTC V1.00.013

CHANNEL

ASIC D279

CPU V3.07.00

Typical Installer Menu

PICTURE

OPTION

External MPI Control

To control the TV using an external MPI control device, you must use the TV’s GAME

CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118

POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/MPI port circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER

SAVINGS must be set appropriately. See Installer Menu item descriptions as well as

Reference section, “b-LAN Setup & Overview,” for further information.

Note: These TV series are not equipped with MPI card slots.

AUDIO

INPUT

TV Setup Menus

TIME

MY MEDIA

206-4207

7

8

Commercial Mode Overview (Cont.)

FTG Mode

This mode enables Pro:Idiom

®

decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns the

FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be used is vital in determining the owner.

FTG Mode via CPU and FTG Mode via EBL are two separate and distinct FTG Modes of operation, each with its own unique advantages and requirements as described later in this document. When the TV CPU is configured with an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls the operation of the TV.

Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, configuration can begin. Configuration of either requires a PC application—the LG FTG File Manager for the TV CPU or the

LG FTG Device Configuration Application for the EBL. Each application provides utilities that enable you to create/edit an FTG Channel Map and configure Installer Menu settings. See pages 41 to 52 for further information on FTG Mode operation and configuration.

Remote Management in FTG Mode

When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and

FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric™ Server

Admin Client User Guide for further information.

When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows hospital/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communicate with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu settings.

See Reference section, “b-LAN Setup & Overview,” for further information.

AAA

+

AAA

+

Installing Batteries in Installer Remote

• Remove the battery compartment cover on the back side of the remote by pressing the arrow tab forward and lifting.

• Install two high-quality alkaline 1.5V AAA batteries. Never mix old or used batteries with new ones. Install batteries matching correct polarity as shown (+ with + and - with -).

• Replace the battery compartment cover.

206-4207

Pro:Centric Operation

Pro:Centric TV Interactive Menu Features

The interactive Pro:Centric TV enables patients and visitors—from the comfort of their hospital rooms—to view and select from a complete listing of hospital services and amenities. The Pro:Centric TV is connected to the hospital’s billing computer, and service/amenities charges are billed at the time of order.

Interactive amenities may include:

Hospital information, news, and events

Directory services (local restaurants, hotels, shopping centers, etc.)

Interactive maps (hospital guest dining areas, gift shops, etc.)

Local weather condition and forecast information

Use the Pro:Centric pillow speaker to operate both interactive menus and regular TV features. Press

PORTAL on the Pro:Centric pillow speaker to access the interactive menus.

Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.

Channel Guide

Shows available TV networks and logical channels. When available, electronic program guide (EPG) data provides additional channel and program information.

Information

Typically displays hospital information, as well as information on local weather and services.

Help

Provides help for navigating the interactive menus.

Watch TV

Removes the interactive menu from the screen and returns to the previously tuned TV channel.

Pro:Centric Setup

The Pro:Centric server provides the following functionality:

Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides remote management/administration facilities for downloading splash screens and software/firmware updates as well as facilities for downloading FTG Channel Map and FTG Installer Menu settings for TVs that are in FTG Mode via CPU.

The Data Channel must be set appropriately in the Installer Menu (item 119 DATA CHANNEL) to enable

Pro:Centric remote management/administration facilities.

Pro:Centric application: The application, which operates in conjunction with FTG and PPV Modes, comprises the Pro:Centric interactive menus/features described above. Pro:Centric application settings are managed via the Pro:Centric server Admin Client.

In addition to the Data Channel, the Pro:Centric Application Mode must be set appropriately in the

Installer Menu (item 098 PRO:CENTRIC) to enable the Pro:Centric application.

Administration and management options for the Pro:Centric server are described in detail in the

Pro:Centric™ Server Admin Client User Guide. This document describes only those settings that must be specified on the TVs.

206-4207

9

Installer Remote Control Typical Key Functions

An LG Installer Remote (p/n: 124-213-07) is required to set up and operate the TV. The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV.

MUTE

Switches sound On or Off.

SAP

Analog Mode: Selects MTS sound (Mono,

Stereo, or SAP). DTV Mode: Changes the audio language, if additional languages are available. *

INFO

Displays channel information. **

CC

Press to activate subtitles, unless the Channel

Preview/Banks Setup Menu is currently on the screen, in which case this option displays the

Lock (V-Chip) Menu.

NUMBER Buttons (0 - 9) & DASH

Use to enter a program number or channel. Dash is used for sub-channel numbers such as 9-1,

9-2, etc.

FLASHBK (Flashback)

Returns to the previously tuned channel.

Up/Down/Left/Right Arrows

Use to navigate on-screen menus and adjust TV settings to your requirements.

MUTE POWER

BANK

CH

PREVIEW GUIDE

SAP INFO CC

VOL

CH

OK

CH

VOL

FLASHBK

TIMER MENU ALARM

ADJ

ADJ

ADJ

ADJ

BED1

BED2

**

*

SAP notes:

SAP settings are retained for individual analog channels when TV is turned Off/On.

If SAP is selected and no SAP is provided, sound may not be heard on channel.

Each analog channel may have its own SAP setting.

Digital channels will reset to default audio language when TV is turned Off/On.

The INFO feature is only applicable if the TV is configured for Pro:Centric operation.

POWER

Turns the TV On or Off.

BANK

Selects Channel Bank 1, 2, 3, or 4.

CH PREVIEW

Displays and exits the Channel Preview/Banks

Setup Menu.

GUIDE

Function not supported on these TVs.

CHANNEL UP/DOWN

Selects available channels found with Auto Tuning

(Auto Search).

VOLUME UP/DOWN

Increases/decreases sound level.

OK (Enter)

Use to direct tune channels and also to adjust TV settings.

TIMER

Sets the amount of time before the TV automatically turns itself Off.

MENU

Displays the TV setup menus on the screen.

Also exits the on-screen menu system and returns to TV viewing.

ALARM

Enables users to schedule a one-time “alarm” event, in which the TV turns itself On at the user-specified time.

Bed Switch

Set to Bed 1 or Bed 2 as applicable (per

Installer Menu item 027 HOSPITAL MODE setting).

10

206-4207

Express Script Installer Menu Wizard

The Express Script Installer Menu Wizard guides you through the process of setting up the essential items for most hospital TV viewing applications and is displayed each time the TV is turned ON, unless it previously has been completed or exited.

Note: If previously completed or exited, the Express Script Installer Menu Wizard can be re-activated from the Installer Menu—set Installer Menu item

117 FACT DEFAULT to 001 to initiate the Express Script Installer

Menu Wizard. See the “Installer Menu” section of this document for further information.

Note: If you plan to create a customized Master TV Setup using the procedure on pages 15 to 18, transfer

(Teach) a Master TV Setup to a Target TV, or configure a TV for FTG Mode of operation, be sure to exit the

Express Script in order to avoid setup conflicts that may cause the TV to malfunction.

Note: If you bypass the Express Script, pillow speaker functionality will not be enabled unless you set Installer Menu item 027 HOSPITAL MODE appropriately. See the “Installer Menu” section of this document for further information.

Installer Menu Wizard

Select Menu Mode

Which menu mode will you be using?

Express Script

Exit Express Script

Upon launching, the Express Script Installer Menu Wizard prompts you to select a menu mode. Use the Up/Down arrow keys on the Installer Remote to select the appropriate option:

Select/highlight Express Script in order to proceed with the Installer

Menu Wizard. Then, press OK (Enter) on the Installer Remote.

Select/highlight Exit Express Script to exit the Installer Menu Wizard.

Then, press OK (Enter) on the Installer Remote.

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

OK

The following procedure describes the Express Script Installer Menu Wizard. Use the Installer Remote to make selections and complete each step. You can select the Back button, where available, to check previous settings, as necessary.

Note: If you opt to exit the Express Script Installer Menu Wizard at any time while it is in progress, any settings made will not be retained.

Installer Menu Wizard

1 2 3 4 5 6 7 8

Step 1. Tuning Band

Which tuning band would you like to use?

F

Exit Script

G

Back

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

Next

OK CC

Exit Express Script

1. Select the tuning band.

Use the Left/Right arrow keys to select the appropriate tuning band

(Cable Standard [default], Cable HRC, Cable IRC, or Air). When you have made your selection, use the arrow keys to select Next, and then press OK (Enter).

(Continued on next page)

206-4207

11

Express Script Installer Menu Wizard (Cont.)

(Continued from previous page)

Installer Menu Wizard

1 2 3 4 5 6 7 8

Step 2. Aux Input

Which inputs will you be using?

Customize Inputs.

Use default values.

Back Next

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

OK

CC Exit Express Script

Installer Menu Wizard

Step 3. Speaker Selection

Up/Down/Left/Right arrow keys

F

Exit Script

G

Back

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

1 2 3 4 5 6 7 8

Next

OK CC Exit Express Script

2. Select the Aux inputs.

Use the Up/Down arrow keys to select the desired Aux input option(s).

(Note: If you simply select Next and press OK (Enter) in this step, default values will be used.)

• To customize settings, select Customize Inputs and press OK (Enter).

Aux input options are displayed in a pop-up window. Use the arrow keys to select the input(s) to enable or disable. When you are finished, press

MENU to close the pop-up window. Then, continue with step 3.

• To use default values, select Use default values and press OK (Enter).

Then, continue with step 3.

3. Select the speaker configuration.

Use the Left/Right arrow keys to select the appropriate speaker (Pillow

Only [default], TV Only, or Pillow & TV). When you have made your selection, use the arrow keys to select Next, and then press OK (Enter).

Installer Menu Wizard

Step 4. Pillow Speaker

Up/Down/Left/Right arrow keys

F

Zenith code

Back

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

1 2 3 4 5 6 7 8

Next

OK CC Exit Express Script

Installer Menu Wizard

1 2 3 4 5 6 7 8

Step 5. Channel Access

Do you want to allow direct access to channels not in the channel list?

Yes

Back

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

Next

OK CC Exit Express Script

4. Select the pillow speaker code.

If using the Zenith pillow speaker code (default), you can simply select

Next and press OK (Enter).

Otherwise, select the pillow speaker code field, and use the Left/Right arrow keys to select the appropriate option. When you have made your selection, use the arrow keys to select Next, and then press OK (Enter).

5. Choose whether to allow access to channels outside the channel lineup.

To allow direct access to channels outside the channel lineup (default: Yes), you can simply select Next and press OK (Enter). To limit access to only the channel lineup (after the Express Script is complete) and restrict access to the TV setup menus, select the channel access field, and use the Left/Right arrow keys to select “No.”

When you have made your selection, use the arrow keys to select Next, and then press OK (Enter).

Note: It is recommended that you select “No” to limit access to the channel lineup and prevent end users from accessing channel settings; i.e., the

Channel Menu will be inaccessible/grayed out.

(Continued on next page)

12

206-4207

Express Script Installer Menu Wizard (Cont.)

(Continued from previous page)

Installer Menu Wizard

1 2 3 4 5 6 7 8

Step 6. Auto Search

Would you like to scan for available channels?

Execute Auto Search

Back

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

Next

OK CC Exit Express Script

Installer Menu Wizard

1 2 3 4 5 6 7 8

Step 7. Channel Map Edit

Would you like to edit channel map and icons?

Edit Channel Map.

Back

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

Next

OK

CC Exit Express Script

6. Run the Auto Search (Auto Tuning).

Select Execute Auto Search and press OK (Enter) to start the channel scan (searches for all available analog and digital channels). The system will display progress of the channel scan in a pop-up window. The scan typically takes a few minutes.

When the channel scan is complete, press OK (Enter) on the Installer

Remote to close the pop-up window. Then, continue with step 7.

Note: If you do not want to run the Auto Search (for example, if you intend to manually add only a small number of channels), use the arrow keys to select Next, and then press OK (Enter), and continue with step 7.

Note: You MUST select Execute Auto Search and press OK

(Enter) in order to run the channel scan. If you move on to the next step without running the Auto Search, there will be no channels in the channel lineup (Channel Map).

7. Edit the Channel Map.

This option enables you to add/delete channels, select channel icons, add channel labels, and/or set up channel banks before the Channel Map is transferred to the PTC (see step 8).

Note: The maximum number of channels (analog, digital, and

Aux inputs) that can be transferred to the PTC is 141. An attempt to transfer more than 141 channels of any combination will result in a Channel Map of exactly 141 channels; any extra channels will not be available in the PTC Channel Map. For example, if you enabled three Aux inputs in step 2 and the Auto

Search found 141 channels, you must edit the Channel Map to decrease the number of analog/digital channels to (at most) 138.

Select Edit Channel Map and press OK (Enter) to edit the Channel Map.

Channel edit options will be displayed in a pop-up window (see example on following page). Use the Up/Down arrow keys to navigate between fields:

• Input & CH: Edit the channel lineup, as necessary, to include only free to guest (non-encrypted) channels. Use the Left/Right arrow keys to select channels, and press OK (Enter) to add/delete channels per your system requirements.

(Continued on next page)

206-4207

13

Express Script Installer Menu Wizard (Cont.)

(Continued from previous page)

Searched CH: 1/Added CH: 128

* Available to add up to 141 CH

Input & CH

DIGITAL 2-1

(#0~#212 icon)

Icon

No Logo

Label

Bank

3

4

1

2

* You can use either spinner or numeric key to choose the icon.

Keypad

NORMAL

ADDED

ADDED

ADDED

ADDED

Add/Delete

MENU Exit

Installer Menu Wizard

1 2 3 4 5 6 7 8

Step 8. Completion

Easy installation complete.

Save data… 50%

PTC: V1.00.013 CPU: V03.07.00.01 ASIC: D279

• Icon: Use the Left/Right arrow keys or key in the icon number to select the appropriate trademark/icon for each channel’s Channel-Time on-screen display. Icons are available for familiar channels, such as ABC, CBS,

NBC, etc. Identifiable icons should enable the end user to readily know what common networks are available.

• Label: Press OK (Enter) to display the alphanumeric keypad, and add custom text labels for each channel, as desired. Added custom labels will be displayed above the Label/Keypad field for each channel, as applicable.

• Bank: Use the arrow keys to define channel banks, as desired. See pages

28 to 31 for further information on channel banks.

When you are finished, press MENU to close the pop-up window. Use the arrow keys to select Next, and then press OK (Enter).

Note: You can also edit/add channel icons and/or custom text labels in 2-5-4

+ MENU Mode after the Express Script is completed, if necessary. See page

27 for further information.

Note: If access to the channel lineup will be limited at the completion of the Express Script (see step 5) and you would like to set up channel banks at a later time, you will need to set Installer Menu item 028 CH. OVERIDE to 001 to enable access to the Channel Preview/Banks Setup Menu.

8. Completion

For the final step, the TV will save your settings and transfer the setup to the commercial controller (PTC) (similar to 2-5-5 + MENU Mode during

Custom Master TV Setup). When this step is complete, the system exits the Express Script Installer Menu Wizard.

Note: If desired, you can copy the Express Script TV setup to a cloning tool—a

USB memory device or a clone programmer—for transfer to Target TVs. See cloning procedures in this document.

14

206-4207

Custom Master TV Setup

This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in

Pass-through Mode.

Note: Refer to FTG Mode information on pages 41 to 52 for details on entering FTG Mode and configuring/editing FTG Channel Map and FTG Installer Menu settings.

Before You Begin

It is recommended that you disconnect all Aux inputs if you intend to run Auto Tuning (Channel Search). Under certain conditions, Auto Tuning is disabled if there is an

Aux input active.

If not disabled in the Installer Menu, Aux sources will appear in the channel scan between analog and digital channels after the TV setup is transferred to the commercial controller (PTC).

Determine which cloning tool—USB memory device or clone programmer—is appropriate for your application; several of the Master TV Setup procedure steps are dependent on the cloning tool to be used. See “Cloning

Methods” at right for further information.

If you intend to use a USB memory device, determine the type of file—either the new “.tlx” file format or the legacy

“.tll” file format—to use for cloning purposes; several of the Master TV Setup procedure steps are dependent on the desired file type. See “Cloning Methods” at right for further information.

If the Express Script Installer Menu Wizard is present on the display, exit the Express Script before beginning/continuing the Custom Master TV Setup procedure.

Cloning Methods

See also “Clonable TV Setup Menu Features” list below.

Using a USB Memory Device / .tlx File

The .tlx file format clones Installer Menu settings and all

TV sources’ (analog, digital, AV1, HDMI, etc.) clonable setup menu settings.

Not intended for cloning an auto-tuned/edited Channel

Map, as the channel lineup is converted to a logical FTG

Channel Map when saved (Learned) from a TV to a .tlx file. If the .tlx file with the FTG Channel Map is then used for Teaching purposes, all Target TVs will be configured for FTG Mode via CPU.

Using a USB Memory Device / .tll File

The .tll file format clones the contents of the commercial controller (PTC) memory, including an auto-tuned/edited

Channel Map, Installer Menu settings, and one TV source’s

(analog, digital, or Aux) clonable setup menu settings.

Using a Clone Programmer (TLL-1100A or LT2002)

Both the TLL-1100A and LT2002 clone the contents of the commercial controller (PTC) memory, including an autotuned/edited Channel Map, Installer Menu settings, and one

TV source’s (analog or Aux) clonable setup menu settings.

Clonable TV Setup Menu Features

Channel

Auto Tuning (Channel Lineup)

Manual Tuning

Channel Edit

Channel Label

Picture

Aspect Ratio

Picture Mode

Audio

Auto Volume

Clear Voice

Sound Mode

Balance

TV Speaker

Time

Auto Clock

Auto Off (Sleep Timer)

Option

Language

Caption

Power Indicator

Lock

Movie Rating

TV Rating – Children

TV Rating – General

Notes:

• Some menu options vary between analog and digital channels and Aux inputs.

• The end user only has access to features that are available on the pillow speaker or the user remote control if provided by the institution.

206-4207

15

Custom Master TV Setup (Cont.)

Custom Master TV Setup Procedure

1. Set Installer Menu items.

This step provides specific instruction only on the Installer Menu items that should be set on a Master TV. Refer to pages 19 to 26 for detailed information on all Installer Menu items.

a) Make sure the TV is ON. Then, use the Installer Remote to enter the PTC Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + OK (Enter). b) Set Installer Menu item

117 FACT DEFAULT to 001 and press

OK (Enter) on the Installer Remote.

This clears all Installer Menu custom settings, channel lineup, etc. and reloads the factory default settings. The value will change back to 0 after the PTC has been restored to factory default condition. This step ensures that the TV Channel

Memory will be the active channel lineup.

c) Set Installer Menu item 003 BAND/AFC, as appropriate.

Broadcast: Set to 000.

HRC: Set to 002.

CATV: Set to 001 (default).

IRC: Set to 003. d) Set Installer Menu item 027 HOSPITAL MODE, as appropriate, to select the speaker configuration.

e) Set any other Installer Menu items that affect your TV programming network to the required configuration. For example, enable/disable Aux inputs, set a Start Channel, etc.

f) After you have adjusted all Installer Menu item settings as required, press OK (Enter) once on the Installer Remote to save your changes; then, press OK (Enter) again to exit the menu.

2. Set up TV features.

On-screen setup menus control the features of the TV. Press

MENU on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, Lock, Time, etc. options to the desired configurations. See also Clonable TV Setup Menu

Features list on previous page.

Note: If you intend to clone the PTC, remember that only one TV source’s clonable setup menu settings will be cloned. Thus, for a clone programmer, the TV setup menu settings should be applicable to either an analog channel or Aux input, while for a USB device / .tll file, the TV setup menu settings should be applicable to the analog or digital channel or Aux input to which the Target

TV will be set during the Teaching process.

Note: If desired and if appropriate depending on the cloning method you intend to use (see “Cloning Methods” on previous page), you can run Auto Tuning (see step 3) prior to completing this step.

16

xxLQ630H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ 000

UPN 000-000-000-000

PTC V1.00.013

ASIC D279

CPU V3.07.00

Typical Installer Menu

Note: The Installer Menu header will vary depending on the TV you are setting up.

117 FACT DEFAULT 000

003 BAND/AFC 001

027 HOSPITAL MODE 254

Adjust the values for these

Installer Menu items.

CHANNEL

PICTURE AUDIO TIME

LOCK OPTION INPUT MY MEDIA

Set the TV features to the desired configuration for the end user.

Audio Menu Note: Audio Menu options are inaccessible (grayed out) if

TV Speaker is not selected (i.e., Pillow

Only is selected).

Lock Menu Note: Press 0-3-2-5 to access the Lock Menu if the Lock

System is active and the password is not available.

(Continued on next page)

206-4207

Custom Master TV Setup (Cont.)

(Continued from previous page)

3. (Optional) Run Auto Tuning.

Note: If you intend to use a USB memory device / .tlx file for cloning purposes, DO NOT run Auto Tuning. If you

Teach a .tlx file with an auto-tuned/edited Channel Map to a Target TV, this will put the Target TV in FTG Mode via CPU. Proceed to step 6 to verify the TV setup. (Steps

4 and 5 are not applicable for .tlx files.)

If you run Auto Tuning with the intention to clone the resulting

Channel Map, you must use a USB memory device / .tll file or a clone programmer for this cloning purpose.

CHANNEL

• Auto Tuning

• Manual Tuning

• Channel Edit

• Channel Label

Move Enter a) To search for all available analog and digital channels, go to the

Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.

b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include only free to guest (non-encrypted) channels.

Add/delete channels per your system requirements.

Use Channel Menu options to run Auto Tuning, edit channels, and select channel icons.

Use the Channel Label option in the Channel Menu to select the appropriate trademark/ icon for each channel’s Channel-Time on-screen display. Icons are available for familiar channels, such as ABC, CBS, NBC, etc. Identifiable labels (icons) should enable the end user to readily know what common networks are available.

Note: If you intend to clone the PTC and Installer Menu item 103 ATSC TUNE MODE is set for Physical Channel tuning (default and recommended setting), channels with minor channel numbers higher than 255 will not transfer correctly in step 4. If item 103 is set for

Virtual Channel tuning and either the major or minor channel numbers are higher than

255, the channel(s) will not transfer correctly in step 4.

Note: If you intend to clone the PTC, you can add the channel icons in this step or as described in step 5. Also in step 5, you can add custom text labels for channels without icons.

4. Transfer the TV setup menu settings to the commercial controller (PTC):

2-5-5 + MENU Mode

Note: This step is essential for successful cloning using a USB memory device /

.tll file or a clone programmer. Without this step, the PTC will not contain any of the TV setup menu settings.

Note: The maximum number of channels (analog, digital, and Aux inputs) that can be transferred to the PTC is 141. An attempt to transfer more than 141 channels of any combination will result in a Channel Map of exactly 141 channels; any extra channels will not be available in the PTC Channel Map. For example, if you enabled three Aux inputs in the Installer Menu and Auto Tuning found 141 channels, you must edit the Channel Map to decrease the number of analog/digital channels to (at most) 138.

(Continued on next page)

206-4207

17

Custom Master TV Setup (Cont.)

(Continued from previous page) a) After the TV channel lineup has been edited and channel label icons added, tune to the channel (source) for which you wish to transfer TV setup menu settings.

Note: If you intend to use a clone programmer for cloning purposes, this must be either an analog channel or Aux input.

b) Enter the Installer Menu, and press 2-5-5 + MENU on the Installer Remote to initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer Menu and then tunes through the channels in the channel lineup during the transfer. When the transfer is complete, the TV tunes back to the channel that was tuned before the transfer began.

Note: Scan Mode is not functional until the TV setup is transferred.

5. (Optional) Add Custom Channel and Aux Input Labels:

2-5-4 + MENU Mode

Note: 2-5-4 + MENU Mode enables you to add/edit channel icons and custom text labels in the PTC once the Master TV Setup has been transferred as described in the previous step.

Enter the Installer Menu, and press 2-5-4 + MENU on the Installer

Remote. Add/edit custom text labels and/or change icons for the

Channel-Time on-screen displays (see 2-5-4 + MENU procedural information on page 27). Note that broadcast digital channels often already have a broadcaster generated label. When you are finished, press MENU to exit 2-5-4 + MENU Mode.

DIGITAL 19-3

MONO STEREO SAP

WXYZ

Custom Text Label “WXYZ” created in 2-5-4 + MENU Mode.

6. Verify the TV setup.

Verify that the channel lineup, channel icons, and custom text labels are correct. Also, make sure the TV features are set per your requirements.

028 CH. OVERIDE 000

After verifying the TV Setup, set Installer

Menu item 028 CH. OVERIDE to 000.*

7. Set up channel banks.

Set up channel banks, as desired (see pages 28 to 31).

Note: When you lock the channel lineup (see next step), the Channel

Preview/Banks Setup Menu is no longer accessible via the Installer

Remote. If you wish to set up channel banks at a later time, you will need to set Installer Menu item 028 CH. OVERIDE to 001 to enable access to the Channel Preview/Banks Setup Menu.

8. (Recommended) Lock the channel lineup.

Enter the Installer Menu. Set item 028 CH. OVERIDE to 000 and press

OK (Enter) to lock the channel lineup and restrict access to the TV setup menus. Press OK (Enter) again to save your changes and exit the

Installer Menu. *

The Master TV Setup is now ready to be copied to the predetermined cloning tool—a USB memory device or a clone programmer. See cloning procedures in this document.

*

This step prevents end users from accessing channel settings (i.e., the

Channel Menu will be inaccessible/ grayed out).

18

206-4207

Installer Menu

Use the Installer Menu to set up, change, or view operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing.

Accessing the Installer Menu

1. Make sure the TV is ON.

2. Using an Installer Remote, press MENU repeatedly until the on-screen display of the TV setup menus (if the TV is in Pass-through Mode) or the

Function Menu (if the TV is not in Pass-through Mode) no longer toggles, and then press 9-8-7-6 + OK (Enter) to access the Installer Menu.

The Installer Menu opens with item 000 INSTALLER SEQ 000.

Note: If the password is not entered or registered correctly, you will see the message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu header. Once you re-enter the correct password (i.e., press 9-8-7-6 + OK [Enter]), the Installer Menu will display.

Note: If the TV is in FTG Mode, the Installer Menu is accessible as readonly. Refer to pages 41 to 52 for information on FTG Mode configuration.

xxLQ630H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ 000

UPN 000-000-000-000

PTC V1.00.013

ASIC D279

CPU V3.07.00

Typical Installer Menu

Using the Installer Menu

Refer to the table on pages 20 and 21 for an overview of the available

Installer Menu items, including their item numbers, functions, value ranges, and default values.

Installer Menu items not relevant to these TV series are not present in the

Installer Menu; therefore, some numbers are missing. For example, item

006 will not appear. In addition, items that are dependent on other Installer

Menu item settings will not be initially accessible. For example, item 046

STRT AUX SRCE will not display in the Installer Menu unless item 004

STRT CHANNEL is set to 0.

Navigation within the Installer Menu

Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu items, or access an item directly by keying in the item number and then pressing MENU. For example, to access the SLEEP

TIMER option, which is item 015, press 0-1-5 + MENU.

Changing Installer Menu Settings

To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or enter a valid value directly. To save the new setting, press OK (Enter), or use the Up/Down arrow keys to navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will not be saved.

As part of the Installer Menu header, two

3-character acronyms are displayed to indicate the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV models.

Acronym Description

CPU-CTV Pass-through Mode with

Channel Map in CPU

CPU-FTG FTG Mode via CPU

EBL-FTG FTG Mode via EBL

EBL-LNT LodgeNet PPV Mode

MPI-EXT External MPI Control

PTC-CTV Pass-through Mode with

Channel Map in PTC

Exiting the Installer Menu and Activating Updates

After you have adjusted all Installer Menu item settings as required, press OK (Enter) once on the Installer

Remote to save your changes; then, press OK (Enter) again to exit the Installer Menu. Any changes you make will be stored in non-volatile memory.

Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control) settings in the TV are reset to their default values; that is, the Lock System, if previously enabled from the Lock setup menu (see the Owner’s Manual for additional information), will now be disabled, and the individual Parental

Control settings will be restored to default values.

206-4207

19

Installer Menu (Cont.)

028

029

030

031

032

035

039

046

004

005

007

008

009

010

011

012

013

014

015

016

017

Installer Menu Items 000 through 070

Menu

Item

000

001

002

003

Function

INSTALLER SEQ

POWER MANAGE

AC ON

BAND/AFC

Value Range Default Value

0 ~ 3

0 ~ 7

0 / 1

0 ~ 3

0

1

0

0

020

021

022

023

STRT CHANNEL

CHAN LOCK

STRT VOLUME

MIN VOLUME

MAX VOLUME

MUTE DISABLE

KEY DEFEAT

IR BANKS EN.

SCAN MODE

STRT CH IN SM

SLEEP TIMER

EN TIMER

ALARM

FEATURE LEVEL

V-CHIP

MAX BLK HRS

CAPTION LOCK

0 ~ 127, 255

0 / 1

0 ~ 63, 255

0 ~ 63

0 ~ 63

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 / 1

0 ~ 1, 16 ~ 24,

64 ~ 65

0 / 1

0 ~ 99

0 / 1

255

0

255

1

12

0

1

0

1

0

0

63

0

1

1

1

1

Brief Description of Function

Leave default set to 0.

Sets number of hours of no activity before automatic shutoff.

Set to 1 to enable Auto Turn ON when AC power is applied.

Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

Channel tuned when TV is turned ON. (Set to 255 to tune to channel tuned before TV turned OFF.)

If set to 1, cannot tune from current channel.

Volume level when TV is turned ON. (Set to 255 to use volume level before TV turned OFF.)

Sets minimum allowable volume setting.

Sets maximum allowable volume setting.

Set to 1 to disable Mute Function.

Set to 1 to disable menu navigation keys on display panel.

Set to 1 to enable TV to respond to bank discrete IR codes.

Set to 1 to allow Channel Up/Down to turn ON TV. (See detailed descriptions.)

Set to 1 to use the Start Channel for the Channel Map pivot point in Scan Mode.

Set to 1 to enable Sleep Timer.

Set to 1 to enable On/Off Timers.

Set to 1 to enable Alarm.

Determines an additional IR code scheme to which the TV will respond.

025

027

047

053

069

070

FUNCTION PRE.

HOSPITAL MODE

CH. OVERIDE

OLD OCV

ACK MASK

POLL RATE

TIMING PULSE

COMPPORT EN.

REAR AUX EN

STRT AUX SRCE

AUX STATUS

DIS. CH-TIME

EN. CH-T COL.

FOR. CH-TIME

0 ~ 1

0 ~ 162, 254

0 / 1

0 / 1

0 / 1

20 ~ 169

186 ~ 227

0 / 1

0 / 1

1, 3 ~ 5, 255

0 / 1

0 / 1

0 / 1

0 ~ 7

1

254

0

94

1

0

207

1

1

255

0

0

1

2

Set to 1 to enable V-Chip (Parental Control) functions.

Sets number of V-Chip blocking hours.

Set to 1 to retain caption setting before TV turned Off.

Set to 1 to allow Channel Preview/Banks Setup Menu access via CH

PREVIEW key on Installer Remote.

Set according to the speaker selection, the pillow speaker code/supply voltage, and the hospital IR code. See detailed instructions.

If set to 0, limits direct access to favorite channels.

Set to 1 to change MPI operation to OCV.

If set to 1, enables ACK feature of MPI.

Selects poll rate for MPI.

Sets baud rate for MPI.

Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1.

Set to 1 to enable display panel Video 1 input jack.

Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).

Set to 1 for MPI Aux source to be reported as a channel number instead of

Channel 0.

Set to 1 to disable Channel-Time display.

Set to 1 to enable custom color for the Channel-Time display.

Chooses custom foreground color for the Channel-Time display.

20

206-4207

Installer Menu (Cont.)

Installer Menu Items 071 through 122

Menu

Item

071

073

075

077

078

079

080

081

082

083

084

087

098

106

116

117

118

099

102

103

104

088

090

EN NOISE MUTE

KEY LOCK

091

YPrPb2 EN

094 SAP MENU EN

096 DEF. ASP. RATIO

119

121

122

Function

BCK. CH-TIME

CH NOT AVBLE

REVERT CH

QUICK SHUTOFF

UPN MSB

UPN MSB-1

UPN MSB-2

UPN LSB

CHKSM ERROR

HANDSHK TIME

PERMANENT BLK

REAR RGB EN.

PRO:CENTRIC

BACK LIGHTING

ATSC BAND

ATSC TUNE MODE

START MINOR CH

ASP RATIO LOCK

VIDEO MUTE EN

FACT DEFAULT

POWER SAVINGS

DATA CHANNEL

P:C RF WAKE HR

P:C RF WAKE MN

Value Range Default Value

0 ~ 7

0 / 1

0 / 1

0 ~ 17

0 ~ 23, 128

0 ~ 59

* 201, 202, 255 applicable for LQ630H TVs only.

2

0

0

0

0 ~ 255

0 ~ 255

0 ~ 255

0 ~ 255

0 / 1

0 ~ 5

0 / 1

0/1/17

0 / 1

0 / 1

0 / 1

0 / 1

0 ~ 4

0 ~ 2 0

1 ~ 100, 101 ~ 200,

201, 202, 255 *

0 ~ 4

0 / 1

0 ~ 255

255 (LQ630H)

100 (CQ610H)

4

1

0

0 / 1

0 / 1

0 / 1

1 / 3

0

0

0

3

255

255

255

255

1

5

0

1

1

0

1

1

2

0 ~ 135 0

128

0

Brief Description of Function

Chooses custom background color for the Channel-Time display.

If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message is displayed if user direct tunes a channel that is not in the favorite channel list.

If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.

Allows TV to be turned OFF with press and hold of pillow speaker channel buttons. Set to 0 to disable. Set from 1 to 17 to define hold time. (See detailed descriptions.)

User programmable number, most significant byte.

User programmable number, most significant byte - 1.

User programmable number, most significant byte - 2.

User programmable number, least significant byte.

If set to 1, enforces rigid MPI checksum.

Relaxes MPI timing to be compatible with PC-based Windows-controlled systems.

Removes block hours setting for Parental Control and makes block permanent.

Set to 0 to disable RGB input. Set to 1 to enable RGB input.

Set to 17 for Auto Configure.

If set to 1, audio is muted if no signal is present.

If set to 1, keyboard is locked out, IR is still functional.

Set to 0 to disable HDMI 2. Set to 1 to enable HDMI 2.

Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on

Function Menu.

Sets default aspect ratio at power up. See detailed descriptions and item 106.

Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for

GEM (Java Application) Mode.

Sets the level of the TV picture back lighting. (See detailed descriptions.)

Selects ATSC band.

Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.

Selects Minor Start Channel. Set to 0 for NTSC.

To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.

Set to 0 for Normal. Set to 1 for Blank.

Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.

Set to 3 (default—b-LAN module only powered when TV is turned ON), or set to 1 (b-LAN module is always powered). (See detailed descriptions.)

Set to 0 to disable. Set to the RF channel number of the data channel for

Pro:Centric or TV E-Z Installation data. (See detailed descriptions.)

Sets the hour for Wake On RF. The value “128” is displayed as “OFF.” Directly entering 128 turns the Wake On RF feature OFF.

Sets the minute for Wake On RF.

Caution: Installer Menu settings may affect options available from the TV setup menus or the Function Menu.

206-4207

21

Installer Menu (Cont.)

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Specifies entry sequence to the Installer Menu.

0 = 9876

2 = 1478

1 = 4321

3 = 3698

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The

Power Management function is for saving energy. If set to 0,

Power Management is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain ON, unless there has been activity from either the control panel or remote control.

002 - AC ON (AC Power Switchable)

If set to 1, this allows the TV to turn ON when AC power is applied. Pressing the ON button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use the Left/Right arrow keys to choose 0 or 1, where 0 is the default (OFF), and 1 is ON.

Note: If set to 1 (ON), the TV does not respond to ON/OFF commands from either the remote or the display panel, and the

SLEEP TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control)

There are four possible settings for this option:

0 = Broadcast

2 = HRC

1 = CATV (default)

3 = IRC

If some channels were not found by Auto Tuning (Channel

Search), select the appropriate Band setting here, and add the channels using the Channel Edit option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial Major

Start Channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned ON. If set to 255, the last channel tuned before the TV was turned OFF will be the channel tuned when the TV is turned ON again.

0 = Aux

1 ~ 125 = Major CH #

126 = Map to Major CH 3

127 = Map to Major CH 4

255 = Last Channel

Note: For a digital Start Channel, always remember to set item

104 to the Minor Start Channel number.

Note: 126 and 127 are mapped only in LodgeNet PPV Mode.

005 - CHAN LOCK (Channel Lock)

Channel Lock is ideal if the system must always be on the same channel. Changing channels with the Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).

Generally, this feature is used in connection with item 004 STRT

CHANNEL where the Start Channel may, for example, be set to

3 or 4. If the Start Channel is 3, then the TV will remain locked on channel 3.

22

NOTE: For items 007, 008, and 009

For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV.

To translate a TV volume level to the Installer Menu value, use the following formula:

Installer Value = TV Value x 63

100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned ON. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned OFF; at turn ON, the volume level will be automatically set at the previous or last level.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 6. Use the Left/Right arrow keys to change values.

The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every TV.

Note: The minimum volume level cannot have a value setting higher than the maximum volume level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the Volume (VOL) Up/Down controls. In this way, for example, someone cannot set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN

VOLUME is also set at 0. Use the Left/Right arrow keys to change values. It may be best to set the same value on every TV.

Note: The maximum volume level cannot have a value setting lower than the minimum volume level (described above).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, KEY DEFEAT prevents the end user from accessing the on-screen menu(s) from the display front panel—MENU, OK/

ENTER, and menu navigation keys do not function. If set to 0, those keys do function.

Note: Users can always access the menu(s) by pressing MENU on the remote.

206-4207

Installer Menu (Cont.)

012 - IR BANKS EN (IR Banks Enable)

For direct access to a particular channel bank. When enabled, you can access a channel bank by inputting the discrete IR code for that bank.

Note: This item is not available in the Installer Menu when item

027 HOSPITAL MODE is set to 0.

013 - SCAN MODE (Functional after 2-5-5 + MENU transfer of

Channel Map)

When set to 1 (default), allows TV to be turned ON when Channel

Up/Down buttons are pressed on pillow speaker. Also, TV will turn

OFF when Channel Up/Down key is used to tune above or below

Channel Map pivot point. By default, Channel Map pivot point is between the highest and lowest channel in the Channel Map (also see item 014 STRT CH IN SM). Set to 0 to disable.

014 - STRT CH IN SM (Start Channel in Scan Mode)

Only valid when item 013 SCAN MODE is set to 1 (enabled).

When set to 1, forces Channel Map pivot point to be between the

RF channel designated in item 004 STRT CHANNEL and next lower channel in the Channel Map. Set to 0 to disable (default).

Note: This item is not available in the Installer Menu when item

013 SCAN MODE is set to 0.

015 - SLEEP TIMER

If set to 1, the Sleep Timer feature may be used. If set to 0, the

Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers)

If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers.

Note: Clock must be set in order for timers to be used.

017 - ALARM

Gives the installer the option of making the Alarm function available to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function.

Note: Clock must be set before the Alarm function will work.

020 - FEATURE LEVEL

This function determines an additional IR code scheme to which the TV will respond, allowing for the use of unique IR codes based on “bed number” in a multi-TV single room installation. First determine the IR mode; then select the bed number.

Note: Item 027 HOSPITAL MODE must be set to 0 to enable

Legacy Zenith Bed 1 or Bed 2 IR codes and Speaker selections.

Values

0 – 1

16 – 24

64 – 65

IR Mode

Legacy Zenith (Hospital)

Multi-code Remote

Legacy Zenith (Hospital)

Bed #

1 – 2

1 – 9

1 – 2

Speaker

TV

TV

Pillow

Note: For further information, see documentation for the accessory package that includes the multi-code remote.

021 - V-CHIP (Parental Control)

Set to 1 to activate V-Chip (Parental Control) and have it available to the end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn the V-Chip feature

Off (not available to user); no programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours)

Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

Note: This item is not available in the Installer Menu unless item

084 PERMANENT BLK is set to 0.

023 - CAPTION LOCK

If set to 0, captions are OFF when the TV is turned ON. Set to 1 to use the caption setting configured before the TV was turned

OFF when the TV is turned ON.

025 - FUNCTION PRE (Function Preview)

Set to 1 to allow access to the Channel Preview/Banks Setup

Menu via the CH PREVIEW key on Installer Remote. Set to 0 to disable access to the Channel Preview/Banks Setup Menu.

027 - HOSPITAL MODE

Set according to the speaker selection, the pillow speaker code/ supply voltage and the hospital IR code.

Value

000

066

081

082

097

098

129

130

145

146

161

162

254

001

002

017

018

033

034

065

Speaker

Determined by item 020 setting

Pillow Only

Pillow Only

Pillow Only

Pillow Only

Pillow Only

Pillow Only

TV Only

TV Only

TV Only

TV Only

TV Only

TV Only

Pillow & TV

Pillow & TV

Pillow & TV

Pillow & TV

Pillow & TV

Pillow & TV

TV Only

Pillow Speaker

Code/Voltage

Zenith (+12v)

Zenith (+12v)

Zenith (+12v)

Philips (+5v)

Philips (+5v)

RCA (-5v)

RCA (-5v)

Zenith (+12v)

Zenith (+12v)

Philips (+5v)

Philips (+5v)

RCA (-5v)

RCA (-5v)

Zenith (+12v)

Zenith (+12v)

Philips (+5v)

Philips (+5v)

RCA (-5v)

RCA (-5v)

0v

Hospital IR Code

Disabled

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #1

Zenith Bed #2

Zenith Bed #2

When Hospital Mode is enabled, channel banks are also available. Refer to channel banks information in this document for further details. Channel banks are not supported if Hospital Mode is set to 0 or on TVs that are configured for FTG Mode operation.

206-4207

23

Installer Menu (Cont.)

When Hospital Mode is set to 0 (disabled), both the IR code that will control the TV and the speaker selection depend on the

Installer Menu item 020 FEATURE LEVEL setting.

Note: The default setting (254) is not selectable in the Installer

Menu. If you ever need to restore the default setting, you must set item 117 FACT DEFAULT to 1 to reload the factory default settings.

See item 117 description for further information.

Note: In the Installer Menu, an informational code is displayed at the right of each Hospital Mode value. Each code consists of three characters. The first character—T, P, or B—identifies the speaker: TV, Pillow, or Both. The second character—Z, P, R, or D—identifies the pillow speaker code: Zenith, Philips, RCA, or

Disabled. The third character—1 or 2—identifies the bed number.

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either Channel Up/

Down or by direct keypad entry. If set to 0, only those channels that are active in the TV’s memory can be selected.

029 - OLD OCV (On Command Video™)

Set to 1 for operation with systems from On Command Corporation.

030 - ACK MASK

MPI Communication Parameter. When set to 1, enables ACK feature of MPI.

031 - POLL RATE

MPI Communication Parameter. Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI.

032 - TIMING PULSE

MPI Communication Parameter. Sets baud rate for MPI. Step size of 4.3 uS. Changing from default may affect communication via MPI.

035 - COMPPORT EN. (Computer Port Enable)

Set to 1 to enable display panel HDMI 1 input. Set to 0 to disable display panel HDMI 1 input.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting Aux source. When turned ON, the TV will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.

1 = Video 1

3 = HDMI 1

4 = RGB

5 = HDMI 2

255 = Last Aux

Note: Above is applicable only if all Aux sources are enabled.

Note: This item is not available in the Installer Menu unless item

004 STRT CHANNEL is set to 0.

047 - AUX STATUS

Set to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identification change.

Controls MPI status channel response for Aux inputs.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display; Channel-Time display will not appear. Set to 0 to enable the Channel-Time display.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)

Set according to Color Chart:

0 = Black

1 = Blue

2 = Green

3 = Cyan

4 = Red

5 = Violet

6 = Yellow

7 = White

Note: If foreground color and background color are the same, the menu background will be transparent.

Note: Applies only to “Channel Not Available” message if item

073 CH NOT AVBLE is set to 1 (enabled). Also, items 070 FOR.

CH-TIME and 071 BCK. CH-TIME are not available in the Installer

Menu when item 069 EN. CH-T COL. is set to 0.

071 - BCK. CH-TIME (Channel-Time Display Background Color)

See description for item 070 FOR. CH-TIME above. The color chart is the same for both items.

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL-

ABLE” message is displayed when a user direct tunes a channel that is not in the channel scan list available in memory.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of MPI communication occurs, TV automatically tunes to the specified Start Channel.

Note: This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 255.

077 - QUICK SHUTOFF

Allows end user (patient) to turn OFF TV using mechanical (analog)

Pillow Speaker Channel Up/Down buttons. Patient needs to press and hold either channel button for time determined by value set. Set to 0 to disable. Set from 1 to 17 to establish required hold time of button—from 2 seconds to 10 seconds in half-second increments.

Note: This item is not available in the Installer Menu when item

013 SCAN MODE is set to 0.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable by

MPI command. Note: Not linked to serial number.

24

206-4207

Installer Menu (Cont.)

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 readable by

MPI command. Note: Not linked to serial number.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 readable by

MPI command. Note: Not linked to serial number.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable by

MPI command. Note: Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid MPI checksum validation. Set to 1 for validation.

Set to 0 to disable (does not check checksum on MPI async port).

SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PC- based Windows controlled systems. Range is 0 - 5.

(Timeout = 25.5MS + [25.5 MS* Handshake time].)

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental

Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 to initiate a onetime automatic configuration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes when no signal is present.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up.

• Set to 0 for Set By System.

• Set to 1 for 4:3.

• Set to 2 for 16:9 (default).

• Set to 3 for Just Scan.

• Set to 4 for Zoom.

Note: This item is not available in the Installer Menu unless item

106 ASP RATIO LOCK is set to 0.

098 - PRO:CENTRIC

Selects the Pro:Centric Application Mode. Set to 0 (default) to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for

GEM (Java Application) Mode.

Note: This item is not available in the Installer Menu when item

119 DATA CHANNEL is set to 0.

099 - BACK LIGHTING

Sets the TV screen brightness at power up. Default setting is 255.

• 1 - 100 Static Back Lighting

(1 = Dimmest picture, 100 = Brightest picture)

• 101 - 200 Dynamic Back Lighting

(101 = Dimmest picture, 200 = Brightest picture)

The TV automatically controls back lighting depending upon the picture level of the current program.

• 201 Automatic Static Back Lighting

The TV automatically controls back lighting depending upon external spectral sensitivity.

• 202 Automatic Dynamic Back Lighting

The TV automatically controls back lighting depending upon external spectral sensitivity and the picture level of the current program.

• If set to 255, back lighting is controlled via the Picture settings in the TV setup menus.

090 - KEY LOCK

If set to 1, front keyboard Channel, Volume, and Caption buttons are disabled, Power button remains enabled. If set to 0, Channel,

Volume, Caption, and Power buttons are all enabled.

091 - YPrPb2 EN. (HDMI2 Enable)

Set to 1 to enable display panel HDMI 2 input. Set to 0 to disable display panel HDMI 2 input.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:

0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.

103 - ATSC TUNE MODE

Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function menu, if Function

Menu is available (i.e., the TV is not in Pass-through Mode). Set to 0 to disable SAP feature on Function Menu, if Function Menu is available.

104 - START MINOR CHANNEL

Sets Minor Start Channel number at power up. 0 = NTSC. If not

0, number selected is the digital channel’s Minor Start Channel number.

Note: This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 0 or 255.

206-4207

25

Installer Menu (Cont.)

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP.

RATIO above.

116 - VIDEO MUTE EN (Video Mute Enable)

Set to 0 for Normal. Set to 1 for Blank.

117 - FACT DEFAULT (Factory Default)

Set to 0 for normal. Set to 1 to load presets of all Installer Menu item settings. Setting this item to 1 will also re-activate the Express

Script Installer Menu Wizard (see pages 11 to 14).

Caution: If set to 1, this will reload the factory defaults

and clear the channel lineup, including any assigned channel icons and custom text labels.

Note: See also Reference section, “Resetting Factory Defaults on the TV(s),” for further information.

118 - POWER SAVINGS

Default set to 3—the power circuitry for both the embedded b-

LAN module and the GAME CONTROL/MPI port is only powered when the TV is turned ON. When the TV is in Standby Mode, the embedded b-LAN and the GAME CONTROL/MPI port are not powered.

Note that the TV must be turned ON in order to communicate with the embedded b-LAN module for configuration and control when

POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1, the b-LAN module is always powered.

Similarly, if MPI communication is required for external MPI control, POWER SAVINGS should be set to 1 so that the GAME

CONTROL/MPI port circuitry is always powered.

Note: See Reference section, “b-LAN Setup & Overview,” for further information.

119 - DATA CHANNEL

Set to 0 (default) to disable. Set to the RF channel number of the data channel for Pro:Centric or TV E-Z Installation (splash screen, configuration, and firmware) data.

The TV may take several minutes to load EPG data after AC power is initially applied.

121 - P:C RF WAKE HR

Set the hour from 0 to 23 for Wake On RF. This item uses the 24hour clock format. The value “128” is displayed as “OFF.” Directly entering 128 turns the Wake On RF feature OFF.

Note: This item is not available in the Installer Menu when item

119 DATA CHANNEL is set to 0.

122 - P:C RF WAKE MN

Set the minute from 0 to 59 for Wake On RF.

Note: This item is not available in the Installer Menu when item

119 DATA CHANNEL is set to 0 or when item 121 P:C RF WAKE

HR is set to 128/OFF.

26

206-4207

Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)

Changing Channel Icons and/or Adding or Editing

Custom Text Labels in the Channel-Time Display

If there is no pre-assigned icon for a channel, you can add a custom text label of up to seven (7) characters to help identify the channel or network. Also, if desired, a custom text label can be added to the Channel-Time display in addition to a pre-assigned icon. You may also add text labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.

XYZ

XYZ

1 2 3 4 5 6 7

(Icon)

XYZ

NETWORK

(Custom Text Label)

Changing icons and/or adding or editing custom text labels can only be done if there are channels that have been transferred to the TV’s PTC either during the Express

Script/Custom Master TV Setup (see pages 11 to 14 or pages 15 to 18, respectively) or by cloning (USB memory device / .tll file or clone programmer only).

Note: A blank letter space is available between “Z” and “!”.

To perform channel editing/labeling:

1. Enter the TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + OK (Enter).

2. Press 2-5-4 + MENU on the Installer Remote to enter the Channel Label Editing Menu.

3. Change channel icons and/or add or edit custom text labels as described in the procedures below. (You can do this more than once.)

4. To exit the menu when you are done, press MENU.

Changing a Channel’s Icon on the Master TV

1. Use Channel Up/Down to select the desired channel.

2. Use the Left/Right arrow keys to select the thin letter “ I” on the

Channel-Time display.

3. Use the Up/Down arrow keys to select the icon with which you want to identify the channel. (If you know the icon number, enter the number, and press OK [Enter].)

4. Proceed to add/edit custom text labels, or go to the next channel.

Adding/Editing Channel Labels on the Master TV

1. Use Channel Up/Down to select the desired channel.

2. Press the Left or Right arrow repeatedly until the numbers 1 to 7 appear on the display. The number shows the position of the character that can be changed. Number 1 is the first character, number 2 the second character, etc.

3. Use the Up/Down arrow keys to select the desired character.

4. Proceed to the next number position, or go to the next channel.

Adding/Editing Source Labels on the Master TV

1. Press BANK to select the desired

Aux input source: AV1, RGB,

HDMI1, or HDMI2.

2. Press the Left or Right arrow repeatedly until the numbers 0 to 9 appear on the display. The number shows the position of the character that can be changed.

3. Use the Up/Down arrow keys to select the desired character.

4. Press BANK for the next Aux input, or use Channel Up/Down to return to channels.

Installer Remote Control Key Functions for Master TV Channel Label Editing Menu

Channel Up/Down: Tunes to the next channel in scan.

Left/Right Arrows: Select the item to change. If “I” is shown, the icon can be changed. If a number is shown, it indicates the position of the character that can be changed.

Up/Down Arrows: Select the icon or the character to be displayed. Tip: Arrows can be held down for fast scrolling.

0 – 9: Use to enter the index number of the icon, if known.

OK (Enter): Changes the icon after the icon number has been entered.

BANK: Use to select Aux inputs.

MENU: Exits the editing process.

206-4207

27

Channel Banks Setup

Channel Banks Overview

Channel Banks enable institution administrators to create tiered channel programming on patient in-room

TVs. Each channel bank may offer a custom channel lineup for a pre-determined fee. LQ630H and

CQ610H TVs are configured with four channel banks, i.e., Channel Banks 1, 2, 3, and 4. The top tier generally contains the most programming (premium, etc.), 2nd tier = lesser programming, 3rd tier = basic programming, etc. It is also possible to create an Inactive TV display with Channel Bank 4, so that an

“Inactive TV Call Attendant” message appears when the TV is turned ON. In this case, an administrator can then select another channel bank on the patient’s in-room TV depending on the programming tier requested by the patient.

All channels found during Auto Tuning automatically will be “ADDED” to all four channel banks, and the default is for all channels to be active (NORMAL) in Channel Banks 1, 2, 3, and 4.

Note: Channel banks are not supported on TVs that are configured for FTG Mode operation.

Before You Begin

Run the Express Script Installer Menu Wizard or complete the Custom Master TV Setup procedure (see pages 11 to 14 or pages 15 to 18, respectively).

Note: Channel banks can be defined as part of the Express Script Installer Menu Wizard, if desired.

However, if you are setting up channel banks after completing the Express Script or if you are creating a customized Master TV Setup, use the Channel Preview/Banks Setup Menu as described below.

Installer Menu item 028 CH. OVERIDE must be set to 001 to allow access for channel banks setup.

Accessing the Channel Preview/Banks Setup Menu

1. To select a channel bank, press BANK on the Installer Remote. The first time you press the BANK key, the TV display will show the currently active channel bank. Press BANK repeatedly until the desired channel bank is selected.

2. After the desired channel bank is selected, press CH PREVIEW on the Installer Remote to display the

Channel Preview/Banks Setup Menu (see below).

CHANNEL PREVIEW - BANK 1

CH 011-001 NORMAL-ADDED

Typical Channel

Preview/Banks Setup

Menu

Enter -> Change

CC -> VCHIP Menu, Ch. Preview -> Exit

28

Note: In the Installer Menu, all available Aux inputs are enabled by default. The Aux inputs will appear between the highest analog and lowest digital channel number in the channel lineup when Channel Up/Down is used on the Installer Remote. If an Aux input will not be used, it is advisable to disable it. If using the Express

Script, customize the Aux inputs as appropriate in the Aux Input screen (step 2) of the Installer Menu Wizard before completing the Express Script. If performing the Custom Master TV Setup procedure, refer to Installer

Menu items 035, 039, 087, and 091 before performing the 2-5-5 + MENU operation (step 4). After the TV setup is transferred to the PTC, the only way to remove Aux inputs from the channel lineup, is to go to the

Channel Preview/Banks Setup Menu and select NORMAL-DELETED.

206-4207

Channel Banks Setup (Cont.)

Channel Status Options for Channel Banks

In the Channel Preview/Banks Setup Menu, use the Channel Up/Down arrows on the Installer Remote to navigate to a channel and the Left/Right arrows to select the channel status.

CHANNEL PREVIEW - BANK 1

CH 011-001 NORMAL-ADDED

Enter -> Change

CC -> VCHIP Menu, Ch. Preview -> Exit

IDs currently selected channel bank.

IDs currently selected channel.

IDs channel status in selected bank.

Channel Status Options

• NORMAL-ADDED: Channel will appear in channel lineup.

NORMAL-DELETED: Channel will not appear in channel lineup.

BLANK-ADDED: Channel will appear in all channel banks; however, video will be black, no picture.

BLANK-DELETED: Channel will be blanked in all channel banks.

Typical Channel Preview/Banks Setup Menu

Adding / Deleting / Blanking Channels

It is best to complete ADD / DELETE customization before assigning BLANK status. All channels found during Auto Tuning are automatically assigned NORMAL-ADDED status in Channel Banks 1, 2, 3, and 4.

NORMAL-ADDED and NORMAL-DELETED status can be assigned independently for Channel Banks 1,

2, 3, and 4. However, a channel blanked, is blanked in all channel banks.

Note: Auto Tuning removes any channels previously customized with ADD / DELETE / BLANK.

Note: On individual TVs, if a channel was not found during Auto Tuning (and was not added during

Express Script/Custom Master TV Setup procedures), it can be added using the Manual Tuning option in the Channel Menu.

Selecting Deleted Channels

To tune to a NORMAL-DELETED channel:

1. Select a channel bank where the channel’s status is NORMAL-ADDED.

2. Navigate to or direct enter the channel number.

3. Select the channel bank where the channel’s status is “NORMAL-DELETED,” and reconfigure the channel status in the Channel Preview/Banks Setup Menu.

Inactive TV Setup

There are two options for creating an inactive TV display on Channel Bank 4. Either:

Select NORMAL-DELETED for each channel in Channel Bank 4, or

Press BANK on the Installer Remote until Channel Bank 4 is selected, and then press CH PREVIEW to display the Channel Preview/Banks Setup Menu. Then, press the SAP key on the Installer Remote to automatically delete all channels in Channel Bank 4.

When the TV is turned ON by the patient, an “Inactive TV Call Attendant” message will appear on the screen, and after a few moments the TV will turn itself OFF. This will prompt the patient to arrange for an available programming package on Channel Bank 1, 2, or 3. Using the Installer Remote, the administrator can select Channel Bank 1, 2, or 3 depending on the entertainment programming tier selected by the patient. When the patient leaves the hospital, the administrator can then select Channel Bank 4 to reinstate the “Inactive TV” message.

206-4207

29

Channel Banks Setup (Cont.)

Channel Banks Worksheets

Use Channel Banks Worksheets (see following page) to create channel status charts as part of the setup process. On the channel status charts, show the status for each channel in all channel banks. This then becomes the patient entertainment programming offerings plan.

The following examples show “before-and-after-customization” portions of channel status charts with analog channels, Aux inputs, and digital channels.

Example: Channel Banks After Auto Tuning

N

K

B

A

2 5 7 AVI1 RGB HDM1 4-1 6-1 13-1 20-5 20-6 30-1 32-1 40-1 40-11 44-1 44-11 45-1 45-11

A A A

A A A

A A A

A

A A A

A A A

A A A

A A A

A A A

A A A

A D A

D D D

A A A

A A A A A A A A A A A A A

A A A A A A A A A A A A A

A A A A A A A A A A A A A

A A A A A A A A A A A A A

A A A A A A A A A A A A A

N

4

B

3

2 A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

A

Example: Channel Banks After Auto Tuning and Customization with Add/Del/Blnk Options

A A A

BC A A

A A A

A A A A A A A A A A A A A

3

4

1

3

4

1

A A A

A A A

BC A A

BC D D

D D D

BC A A

A

A

A

A D D A A A A A A D D D D

A D D A A A A D D D D D D

D D D D D D D D D D D D D

A A A A A A A A A A A A A

2

3

4

BC A A

BC D D

D D D

A

A

A A A

A D A

D D D

A D D A A A A A A D D D D

A D D A A A A D D D D D D

D D D D D D D D D D D D D

A = Active (channel found during Auto Tuning and retains NORMAL-ADDED status)

D = Delete (channel assigned NORMAL-DELETED status in the Channel Preview/Banks Setup Menu)

BC = Blanked Channel (channel blanked using the BLANK channel option in the Channel Preview/Banks Setup Menu)

30

206-4207

Channel Banks Worksheet

1

2

B

A

N

K

3

4

2

3

4

B

A

N

K

1

3

4

1

2

B

A

N

K

1

2

3

4

B

A

N

K

1

2

B

A

N

K

3

4

Use this worksheet to plan your program packages. (Photocopy additional worksheets as needed.)

Channel Number

Channel Number

Channel Number

Channel Number

Channel Number

Date _____________ Installer _____________________________________ Page ___ of ____

Location ______________________________________________________________________

206-4207

31

Cloning Overview

IMPORTANT CLONING INFORMATION

There are four different procedures for cloning a Master TV Setup (including a TV that has been set up using the Express Script Installer Menu Wizard), each with its own advantages and limitations (see also

“Cloning Methods” on page 15):

Using a USB memory device / .tlx file

Using a USB memory device / .tll file

Using a TLL-1100A clone programmer

Using a LT2002 clone programmer

Each cloning method is described in further detail on the pages that follow. As you perform cloning procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed completely, cloning may not work. At each step, pay attention to ensure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step, and cloning may not be successful.

Caution: Copying a blank or incorrect memory into a TV from a clone programmer will cause the TV to operate erratically or become inoperable.

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer.

Before you begin cloning:

Complete the Custom Master TV Setup procedure or run the Express Script Installer Menu Wizard (see pages 15 to 18 or pages 11 to 14, respectively).

All equipment should be connected to power and turned ON.

Both the Master and Target TVs must be in Pass-through Mode.

Learning and Teaching is only possible between identical model TVs.

If using a USB memory device, ensure the USB device has been formatted with FAT format.

If using a USB memory device / .tlx file, ensure that the Master TV Setup does not contain a Channel Map; otherwise, Teaching will result in the Target TV(s) being configured for FTG Mode via CPU.

For both Master and Target TVs—If using a clone programmer, ensure the TV is tuned to either an Aux input or an analog (not a digital) channel.

LT2002 only—Make sure the batteries in the clone programmer are fresh. If batteries are removed, the clone programmer clock time (if set) will be lost (see page 40 for information on the clone programmer clock).

Caution: Do not unplug the TV power cord or remove/disconnect the USB memory device/ clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction or harm the USB device/clone programmer, respectively.

32

206-4207

USB Cloning Procedures

Learning / Teaching a Master TV Setup using a USB Memory Device / .tlx File

USB Cloning Notes

Read the IMPORTANT CLONING INFORMATION on page 32 before beginning any cloning procedures.

In particular, ensure that the Master TV Setup does not contain a Channel Map; otherwise, Teaching will result in the Target TV(s) being configured for FTG Mode via CPU.

You may edit the filename as part of the Learning procedure; however, a file with edited contents will not be recognized.

It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock manually, or use the Auto Clock setting in the TV setup menus.

Learn Setup from Master TV

1. Ensure the Master TV is set up completely and in Pass-through

Mode.

2. Plug the USB memory device into the USB IN port on the Master

TV.

3. Press MENU on the Installer Remote to display the TV setup menus. Use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven times to display the USB Download Menu.

4. To gain access to the “Learn From TV” option in the USB

Download Menu, key in the password used to enter the Installer

Menu (Example: Press 9-8-7-6).

5. Use the Up/Down arrow keys to select Learn From TV (TLX), and then press OK (Enter).

6. To differentiate this .tlx file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press OK

(Enter) when you are ready to initiate Learning.

Learning status will be shown on the progress bar. When the

Learning process is complete, the USB Download menu will reappear on screen.

7. When Learning is done, remove the USB memory device from the

Master TV.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Learn From TV (TLL)

Learn From TV (TLX)

Previous Enter

Send To USB (USB Port1)

Select the file name and press OK to start xxLQ630H-UA00003.TLX

Previous

Learn From TV

UPDATING...

Do not unplug!

Enter

25%

206-4207

33

USB Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a USB Memory Device / .tlx File (Cont.)

Teach Master TV Setup to Target TV

1. Ensure the Target TV is in Pass-through Mode, and then use the

Installer Remote to enter the Target TV Installer Menu: Press

MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + OK (Enter).

2. Set Installer Menu item 117 FACT DEFAULT to 001, and press

ENTER. When the value changes back to 0, press OK (Enter) again to exit the Installer Menu.

3. Plug the USB memory device with the .tlx file into the Target TV

USB IN port.

4. Press MENU on the Installer Remote to display the TV setup menus. Use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven times to display the USB Download Menu.

5. Use the Up/Down arrow keys to select Teach To TV (TLX), and then press OK (Enter).

6. Use the Up/Down arrow keys to select the Master TV Setup you want to install, and then press OK (Enter). Note: Filenames identify the TV and the TLX version (see example at right).

Teaching status will be shown on the progress bar. When the

Teaching process is complete, the USB Download menu will reappear on screen.

7. When Teaching is done, remove the USB memory device from the Target TV, turn OFF the TV, and unplug the TV power cord for

15 seconds.

8. Reconnect the TV power cord, and turn ON the TV. The Master

TV Setup should be resident on the Target TV.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Previous

Receive From USB (USB Port1) xxLQ630H-UA00003.TLX

Enter

Previous

Teach To TV

UPDATING...

Do not unplug!

Enter

50%

34

206-4207

USB Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a USB Memory Device / .tll File

USB Cloning Notes

Read the IMPORTANT CLONING INFORMATION on page 32 before beginning any cloning procedures.

You may edit a filename as part of the Learning procedure; however, a file with edited contents will not be recognized.

It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock manually or use the Auto Clock setting in the TV setup menus.

Learn Setup from Master TV

1. Ensure the Master TV is set up completely.

2. Plug the USB memory device into the USB IN port on the Master

TV.

3. Press MENU on the Installer Remote to display the TV setup menus, use the arrow navigation keys to select/highlight the

Option menu icon, and then press the number “7” key a total of seven times to display the USB Download Menu.

4. To gain access to the “Learn From TV” option in the USB Download Menu, key in the password used to enter the Installer Menu

(Example: Press 9-8-7-6).

5. Use the Up/Down arrow keys to select Learn From TV (TLL), and then press OK (Enter).

6. To differentiate this .tll file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press

OK (Enter) when you are ready to initiate Learning.

Learning status will be shown on the progress bar. When the

Learning process is complete, the USB Download menu will reappear on screen.

7. When Learning is done, remove the USB memory device from the

Master TV.

Learn From TV (TLL)

Learn From TV (TLX)

Previous

Send To USB (USB Port1)

!

Learn From TV

UPDATING...

25%

Do not remove the USB from the port!

Do not unplug!

Enter

Select the file name and press OK to start xxLQ630H-UA00001.TLL

Previous Enter

206-4207

35

USB Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a USB Memory Device / .tll File (Cont.)

Teach Master TV Setup to Target TV

1. On the Target TV, if necessary exit the Express Script Installer

Menu Wizard, and then use the Installer Remote to enter the Target

TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press

9-8-7-6 + OK (Enter).

2. Set Installer Menu item 117 FACT DEFAULT to 001, and press

OK (Enter). When the value changes back to 0, press OK (Enter) again to exit the Installer Menu.

3. Tune/set the TV to an analog or digital channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Custom

Master TV Setup procedure, if applicable).

4. Plug the USB memory device with the .tll file into the Target TV

USB IN port.

5. Press MENU on the Installer Remote to display the TV setup menus, use the arrow navigation keys to select/highlight the Option menu icon, and then press the number “ 7” key a total of seven times to display the USB Download Menu.

6. Use the Up/Down arrow keys to select Teach To TV (TLL), and then press OK (Enter).

7. Use the Up/Down arrow keys to select the Master TV Setup you want to install, and then press OK (Enter). Note: Filenames identify the TV and the TLL version (see example at right).

Teaching status will be shown on the progress bar. When the

Teaching process is complete, the USB Download menu will reappear on screen.

8. When Teaching is done, remove the USB memory device from the Target TV, turn OFF the TV, and unplug the TV power cord for

15 seconds.

9. Reconnect the TV power cord, and turn ON the TV. The Master

TV Setup should be resident on the Target TV.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Previous

Receive From USB (USB Port1) xxLQ630H-UA00001.TLL

Enter

Previous

!

Teach To TV

UPDATING...

50%

Do not remove the USB from the port!

Do not unplug!

Enter

36

206-4207

Clone Programmer Cloning Procedures

Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer.

Cloning is accomplished using the

TV/clone programmer MPI ports for communication (see figure).

TLL-1100A Clone

Programmer

Antenna or CATV

TLL-1100A Cloning Notes

Read the IMPORTANT CLONING

INFORMATION on page 32 before beginning any cloning procedures.

Ensure the TLL-1100A is either fully charged or connected to AC power.

Learning and Teaching is only possible between identical model

TVs; however, the TLL-1100A can store up to eight different Master

TV Setups.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

MPI

Cable

TV Link

Loader

TLL1100A

Ready

MODE

RECEIVE

ENTER

MENU

SEND

TLL-1100A

Learn Setup from Master TV

1. Ensure the Master TV is set up completely.

2. Tune/set the TV to an analog channel or Aux input, and then plug one end of the MPI cable into the TV MPI port.

3. Turn ON the TLL-1100A.

4. Use the MODE button on the TLL-1100A to select Clone Mode.

5. Use the Left/Right arrows on the TLL-1100A to select the Memory CBank

(1 to 8) in which to store the Master TV Setup.

6. Plug the other end of the MPI cable into the MPI port on the bottom of the TLL-1100A. The Clone Selection Menu will display on the TV screen.

7. Press 1 on the Installer Remote to select LEARN FROM TV from the

Clone Selection Menu. Then, press OK (Enter) to transfer the Master TV

Setup into CBankX on the TLL-1100A.

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the TLL-1100A copies the Master

Setup. When the Learning process is complete, a “LEARNING COM-

PLETE” message will be displayed.

8. When Learning is complete, disconnect the MPI cable from the Master TV.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-

-

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

To change menu items, press channel keys or digits.

To execute item, press Enter.

206-4207

37

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.)

(Optional) Set the Clock

Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master

TV’s clock by copying the time from the clone programmer.) The TLL-1100A can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute.

Since the TLL-1100A’s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port.

After the time is copied to the TLL-1100A clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1. On the Target TV, if necessary exit the Express Script Installer Menu

Wizard, and then use the Installer Remote to enter the Target TV Installer

Menu: Press

MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press

9-8-7-6 + OK (Enter).

2. Set Installer Menu item 117 FACT DEFAULT to 001, and press OK

(Enter). When the value changes back to 0, press OK (Enter) again to exit the Installer Menu.

3. Tune/set the TV to an analog channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Custom Master TV

Setup procedure, if applicable), and then connect the MPI cable to the

MPI port on the Target TV. The Clone Selection Menu will display on the

TV screen.

4. Ensure the correct Memory CBank(X) is selected on the TLL-1100A.

5. Press

2 on the Installer Remote to select TEACH TO TV from the Clone

Selection Menu. Then, press

OK (Enter) to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be displayed on the screen during Teaching. When the Teaching process is complete, a “TEACHING COMPLETE” message will be displayed.

6. When Teaching is done, disconnect the MPI cable from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.

7. Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-

-

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

To change menu items, press channel keys or digits.

To execute item, press Enter.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-

THE CLONE IS VERSION VX.X.X

To change menu items, press channel keys or digits.

To execute item, press Enter.

38

206-4207

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

Caution: If the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer.

Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).

LT2002 Cloning Notes

Read the IMPORTANT CLONING

INFORMATION on page 32 before beginning any cloning procedures.

A slow flashing green light indicates that there are communication problems between the TV and the

LT2002. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

If the status indicator is red, the

LT2002 batteries are low and should be replaced. Install four (4) high- quality alkaline AA batteries.

Learning and Teaching is only possible between identical model TVs; however, the LT2002 can store up to three different Master TV Setups.

Antenna or CATV

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REVISION XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

- PRESS ANY KEY TO CONTINUE.

- DISCONNECT CLONE WHEN DONE.

Learn Setup from Master TV

1. Ensure the Master TV is set up completely.

2. Tune/set the TV to an analog channel or Aux input, and then plug one end of the MPI cable into the TV MPI port.

3. If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002

Clone Selection Menu.

4. Press 1 on the Installer Remote to select LEARN FROM TV from the Clone

Selection Menu; then press OK (Enter) to proceed to the Memory Bank

Selection Menu.

5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press

OK (Enter).

Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master

TV Setup.

6. Verify the Learning setup information on the next screen, and then press

POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002.

(Continued on next page)

206-4207

MPI

Cable

Ferrite Core

(TDK, ZCAT

2035-0930)

Connect cable to

TV MPI Jack and follow on screen instructions

Status

Indicator

MPI

Reset

Color

• green battery ok

• red battery low

Blink pattern

• slow power on

no communications

• heartbeat power on

communications ok

®

QuickSet II Programmer

LT2002

LT2002 Clone

Programmer

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

SAVE TV SETUP IN SELECTED

CLONE MEMORY

(1) MEMORY 1 VER XX REV XX

(2) MEMORY 2 VER XX REV XX

(3) MEMORY 3 VER XX REV XX

(4) RETURN TO CLONE MENU

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

COPY SELECTED CLONE MEMORY

TO TV

(1) MEMORY 1 VER XX REV XX

(2) MEMORY 2 VER XX REV XX

(3) MEMORY 3 VER XX REV XX

(4) RETURN TO CLONE MENU

39

-

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.)

(Continued from previous page)

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup.

When the Learning process is complete, a “LEARNING COMPLETE” message will be displayed.

7. When Learning is complete, disconnect the MPI cable from the Master TV.

(Optional) Set the Clock

Set the time on a Master TV’s clock. (If the time has already been copied from a

TV into the LT2002 clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The LT2002 can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute. (Another reason that the LT2002 should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the LT2002’s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port.

After the time is copied to the LT2002 clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1. On the Target TV, if necessary exit the Express Script Installer Menu Wizard, and then use the Installer Remote to enter the Target TV Installer Menu: Press

MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + OK (Enter).

2. Set Installer Menu item 117 FACT DEFAULT to 001, and press OK (Enter).

When the value changes back to 0, press OK (Enter) again to exit the

Installer Menu.

3. Tune/set the TV to an analog channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Custom Master TV Setup procedure, if applicable), and then connect the MPI cable to the MPI port on the Target TV.

4. With “THE CLONE HAS CONTROL OF TV” message on display, press

2 on the Installer Remote to select TEACH TO TV from the LT2002 Clone

Selection Menu. Then, press OK (Enter).

5. Select the LT2002 Memory Bank in which the new Master TV Setup is located, and press OK (Enter).

6. Verify the Teaching setup information on the next screen, and then press

POWER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be displayed on the screen during Teaching. When the Teaching process is complete, a “TEACHING COMPLETE” message will be displayed.

7. When Teaching is done, disconnect the MPI cable from the Target TV, turn

OFF the TV, and unplug the TV power cord for 15 seconds.

8. Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

40

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

SAVE TV SETUP IN SELECTED

CLONE MEMORY

(1) MEMORY 1 VER XX REV XX

(2) MEMORY 2 VER XX REV XX

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-

-

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-

-

TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

COPY SELECTED CLONE MEMORY

TO TV

(1) MEMORY 1 VER XX REV XX

(2) MEMORY 2 VER XX REV XX

(3) MEMORY 3 VER XX REV XX

(4) RETURN TO CLONE MENU

TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER.

206-4207

FTG Mode of Operation Overview

FTG Mode via CPU or EBL

FTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels.

As indicated in the introduction to this document, there are two separate and distinct methods for configuring

LQ630H and CQ610H TVs for FTG Mode of operation: one (new) method is to configure the TV CPU for

FTG Mode operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL

CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE CPU

IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE. LIKEWISE, IF THE EBL IS IN FTG

MODE, THE CPU CANNOT BE SWITCHED TO FTG MODE.

FTG Mode via CPU

This mode provides the following features:

Logical channels mapped to RF delivered content.

Digital RF channel minor (program) numbers up to 999.

FTG Channel Map of up to 600 logical channels.

Start Channel set for RF or Aux input delivered content.

Pro:Centric data delivery over RF.

FTG Mode via CPU requires that you use LG FTG File

Manager PC software to create an FTG Configuration (.tlx) file. In this mode, the CPU is the owner of the FTG Channel Map and must be configured with an FTG Channel Map and FTG Installer Menu settings using one of the following processes:

Local: Configure an individual LQ630H/CQ610H TV via

USB port using an FTG Configuration (.tlx) file on a USB memory device. The “Teach to TV (TLX)” process and associated procedures are described on pages 43 to 47.

Remote: Configure all LQ630H/CQ610H TVs at the site using a Pro:Centric server head end device (Example:

PCS150R). Load an FTG Configuration (.tlx) file on the

Pro:Centric server using the TV E-Z Installation

“Configuration” option in the Pro:Centric Server Admin

Client. Refer to the Pro:Centric™ Server Admin Client

User Guide for further information.

FTG Mode via EBL

This mode provides the following features:

Logical channels mapped to RF delivered content.

Digital RF channel minor (program) numbers up to 255.

FTG Channel Map of up to 141 logical channels.

Start Channel set for RF or Aux input delivered content.

Pro:Centric data delivery over RF.

FTG Mode via EBL requires LG FTG Device Configuration

Application PC software. In this mode, the EBL is the owner of the FTG Channel Map and must be configured with an

FTG Channel Map and FTG Installer Menu settings using one of the following processes:

Local: Configure an individual LQ630H/CQ610H TV’s

EBL via its TV-LINK CFG jack using a direct PC-to-TV connection and the FTG Device Configuration Application.

The “Write” process for an FTG Channel Map and FTG

Installer Menu settings is described on page 48.

Remote: Configure all LQ630H/CQ610H TV EBLs at the site using a Free-To-Guest Management Appliance

(FMA) head end device (Example: FMA-LG101). Refer to the Free-To-Guest (FTG) Device Configuration

Application User Guide and/or the Installation &

Configuration Guide for the FMA device for further information.

206-4207

41

FTG Mode of Operation Overview (Cont.)

While the TV is in FTG Mode:

Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only.

Any FTG configuration changes must be made using either the FTG File Manager (FTG Mode via CPU) or the FTG Device Configuration Application (FTG Mode via EBL). FTG Channel Map Configuration and FTG

Installer Menu Configuration Utilities enable you to make changes, respectively, to the FTG Channel Map and FTG Installer Menu settings as necessary. Based on the initial method used to configure the TV for

FTG Mode operation (via CPU or EBL), all subsequent changes must be transferred to either the TV CPU or the EBL via a process that is in accordance or compatible with that method (see information on local configuration in this document or refer to documentation for the head end device/server for information on remote management).

If it becomes necessary to reset the TV to Pass-through Mode, there are several options that will enable you to do so. Refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information.

Pages 49 to 52 provide overviews of the utilities that comprise the FTG File Manager. Refer to the Free-

To-Guest (FTG) File Manager User Guide for further information on the FTG File Manager. Refer to the

Free-To-Guest (FTG) Device Configuration Application User Guide for information on the FTG Device

Configuration Application.

Determining the TV Operating Mode

To determine the operating mode of the TV, press MENU on the Installer Remote. The menu displayed depends on the operating mode. See examples below.

If the Function Menu appears, the TV is in a mode (FTG, PPV, etc.) that does not allow the end user to change the fundamental TV setup. If the TV setup menus appear, the TV is in Pass-through Mode.

ABC

ASPECT RATIO

16:9

Just Scan

Set By Program

4:3

Zoom

Move Enter

Function Menu

Indicates the TV is not in Passthrough Mode . While the TV is in this mode, Installer Menu settings can be accessed as read-only.

CHANNEL

PICTURE

LOCK OPTION

AUDIO TIME

TV Setup Menus

Shows that the TV is in

Pass-through Mode .

INPUT MY MEDIA

42

206-4207

FTG Mode via CPU

Creating an FTG Configuration File using the FTG File Manager

This section describes how to create an FTG Configuration (.tlx) file that can be saved to a USB memory device. In order to enable Pro:Idiom decryption, it is recommended that you create an FTG Configuration file using the FTG File Manager.

Notes:

FTG File Manager software is available online at: www.LGsolutions.com/ftgsoftware.

There is also an option to save (Learn) an FTG Configuration file from a TV, which may be desirable or required in either of the following situations:

If you want to save customized TV setup menu settings to the FTG Configuration file (in addition to the FTG Channel Map and FTG Installer Menu settings).

If you do not know the RF channels at the site.

See “Learning an FTG Configuration File from a TV” on page 46 for further information. However, if you use this option to save an FTG Configuration file, it is still highly recommended that you open the saved FTG Configuration file in the FTG File Manager to verify the file contents/settings and to enable Pro:Idiom decryption by marking Encrypted channels using the FTG Channel Map Editor.

The procedure below provides an overview of the steps required to create an FTG Configuration (.tlx) file. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information. See also FTG

File Manager sample screens on pages 49 to 52.

1. Install (if necessary) and launch the FTG File Manager (v1.0.0 or higher) on the PC that will be used to create the FTG Configuration (.tlx) file.

2. You have several options at this time:

• To view and/or base a new FTG Configuration file on an existing FTG Configuration (.tlx) file, click the Open button in the TLX File command section of the FTG File Manager main screen, and select the desired (.tlx) file.

A list of the file’s contents will be displayed in the TLX File Contents window. Either double-click on an individual item to copy it or click the Copy All button directly above the TLX File Contents window to automatically copy all the contents of the opened .tlx file to the FTG Configuration List and, if applicable, TV Setup Menu List. Note, though, that while TV setup menu settings can be included in the new FTG Configuration file, the TV setup menu settings are not available for editing.

Edit the configuration of the items in the FTG Configuration List as well as the FTG Configuration

List itself and/or the TV Setup Menu List, as necessary, to create a new file. Then, proceed to step 3 when you are ready to continue.

• To open an existing FTG Configuration (.rml) file created in the FTG Device Configuration Application to use its FTG Channel Map and/or FTG Installer Menu settings, click File and then Open from the

FTG File Manager menu bar, and select/double-click on the desired “.rml” file.

Edit channels and/or settings as necessary, and then proceed to step 3 when you are ready to continue.

• Create a new FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map

Configuration Utility. Up to 600 logical channels can be defined in the FTG Channel Map.

When you are ready to continue, click Configure and then FTG File Manager from the FTG File

Manager menu bar to return to the FTG File Manager main screen, and then proceed to step 3.

(Continued on next page)

206-4207

43

FTG Mode via CPU (Cont.)

(Continued from previous page)

Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List, click on/ highlight the item to be removed, and then click the Remove Item button directly above the applicable

“List” window. To clear both the current FTG Configuration List and TV Setup Menu List contents, click the Clear button in the List command section of the FTG File Manager main screen.

Note: To clear the current TLX File Contents, click the New button in the TLX File command section of the FTG File Manager main screen (above the TLX File Contents window).

3. To add an FTG Channel Map to the FTG Configuration List, click will copy the current mapped channels to the FTG Configuration List.

under FTG Channel Map. This

Note: If you make any change(s) in the FTG Channel Map Configuration Utility to the current data to be included in the FTG Configuration List, you will need to recopy the FTG Channel Map to the FTG

Configuration List.

4. (Optional) Load default FTG Installer Menu settings for the TV:

• Click the down arrow at the right of the Chassis field in the Installer Menu Templates section of the

FTG File Manager main screen, and select the appropriate chassis (22LQ630H or 26/32LQ630H or

42CQ610H) from the drop-down list of available models.

• Click the Load button.

• Use the FTG Installer Menu Configuration Utility to modify settings, if necessary. Then, return to the

FTG File Manager main screen.

5. To add FTG Installer Menu settings to the FTG Configuration List, click under FTG Installer Menu

Settings. This will copy the selected model’s settings to the FTG Configuration List.

Note: If you make any change(s) in the FTG Installer Menu Configuration Utility to the current data to be included in the FTG Configuration List, you will need to recopy the FTG Installer Menu settings to the FTG Configuration List.

6. Click the Save button in the List command section of the FTG File Manager main screen to save the

FTG Configuration List and, if present, TV Setup Menu List contents to an FTG Configuration (.tlx) file on the PC’s hard drive for later use.

In the Save As pop-up window, name the file, and click Save. The default folder path is C:\Program

Files\Zenith\FTG\TLX. Note that the FTG Configuration file will have a “.tlx” extension.

Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List before saving the new file, click on/highlight the item to be removed, and then click the Remove Item button directly above the applicable window. To clear both the current FTG Configuration List and TV Setup

Menu List contents, click the Clear button in the List command section of the FTG File Manager main screen.

7. Transfer the FTG Configuration (.tlx) file to a USB memory device, and proceed to “Teaching FTG

Configuration to a TV” on the following page to transfer the FTG Configuration file to an LQ630H or

CQ610H TV, as applicable.

44

206-4207

FTG Mode via CPU (Cont.)

Teaching FTG Configuration to a TV

This procedure describes how to “Teach” an FTG Configuration file from a USB memory device to a TV.

Ensure you have completed the procedure on the previous page to create the FTG Configuration file before proceeding with the steps below.

Notes:

If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings. You must use a direct PC-to-TV connection as described on page 48 or an FMA head end device to reconfigure the EBL.

If either of the preceding conditions applies, but you wish to switch the TV to FTG mode via

CPU, refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information before proceeding.

1. Plug the USB memory device that contains the FTG Configuration file into the Target LQ630H or CQ610H TV USB IN port.

2. Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode).

3. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “ 7” key a total of seven times to display the USB Download Menu.

4. Use the Up/Down arrow keys to select Teach To TV (TLX), and then press OK (Enter).

5. Use the Up/Down arrow keys to select the FTG Configuration file you want to install, and then press OK (Enter).

The TV will show Teaching completion progress in a new window.

Do NOT remove the USB device until Teaching is complete. When

Teaching is complete, the TV will tune to the first logical channel in the FTG Channel Map.

6. When Teaching is done, remove the USB memory device. The

FTG Configuration should be resident on the Target TV. Also, the

Target TV CPU is now in FTG Mode (if it was previously in Passthrough Mode).

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Previous

Receive From USB (USB Port1) xxLQ630H-UA00005.TLX

Previous

Teach To TV

UPDATING...

Do not unplug!

50%

Enter

Enter

206-4207

45

FTG Mode via CPU (Cont.)

Learning an FTG Configuration File from a TV

To ensure that Pro:Idiom decryption is enabled, it is recommended that you create an FTG Configuration file using the FTG File Manager as described on pages 43 to 44. However, if necessary, this option enables you to save (Learn) an FTG Configuration file from an LQ630H or CQ610H TV to a USB memory device.

Notes:

The option to save (Learn) an FTG Configuration file from a TV may be desirable or required in either of the following situations:

If you want to save customized TV setup menu settings to the FTG Configuration file

(in addition to the FTG Channel Map and FTG Installer Menu settings).

If you do not know the RF channels at the site.

If the TV is NOT already in FTG Mode, you may need to perform some manual configuration on the TV before you start this procedure (see “Optional Manual Configuration / TV Setup” on following page).

1. Plug a USB memory device into the USB IN port on the TV.

2. Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode).

3. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “ 7” key a total of seven times to display the USB Download Menu.

4. To gain access to the Learn From TV options in the USB Download Menu, key in the password used to enter the Installer Menu

(Example: Press

9-8-7-6).

5. Use the Up/Down arrow keys to select Learn From TV (TLX), and then press OK (Enter).

6. To differentiate this .tlx file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press OK

(Enter) when you are ready to initiate Learning.

The TV will show Learning completion progress in a new window.

Do NOT remove the USB device until Learning is complete. When

Learning is complete, the USB Download Menu will reappear on screen.

7. When you are finished, remove the USB memory device.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Learn From TV (TLL)

Learn From TV (TLX)

Previous

Send To USB (USB Port1)

Enter

Select the file name and press OK to start xxLQ630H-UA00005.TLX

-

Previous

Learn From TV

UPDATING...

Do not unplug!

Enter

25%

Note: It is highly recommended that you open this FTG

Configuration file in the FTG File Manager—BEFORE transferring

(Teaching) the file to any TVs—to verify FTG Channel Map and

FTG Installer Menu settings and enable Pro:Idiom decryption by marking Encrypted channels. This will also enable you to confirm channels and add channel attributes, labels, etc.

46

206-4207

FTG Mode via CPU (Cont.)

Optional Manual Configuration / TV Setup

The manual configuration procedures below should only be performed if you do not know the RF channels at the site and need to “Learn” an FTG Configuration file from an LQ630H or CQ610H TV as described on the previous page. Ensure the TV is in Pass-through Mode before you begin.

Set Installer Menu Items

These steps provide specific instruction only on the Installer Menu items that should be set on an LQ630H or CQ610H TV. Refer to pages 19 to 26 for detailed information on all Installer Menu items.

1. Make sure the TV is ON. Then, use the Installer Remote to enter the

Installer Menu: Press

MENU repeatedly until the on-screen display of the

TV setup menus no longer toggles, and then press

9-8-7-6 + OK (Enter).

2. Set Installer Menu item 117 FACT DEFAULT to 001 and press OK

(Enter) on the Installer Remote.

This clears all Installer Menu custom settings, the channel lineup, etc. and reloads the factory default settings. The value will change back to

0 after the commercial controller (PTC) has been restored to factory default condition. This step ensures that the TV Channel Memory will be the active channel lineup.

3. Set Installer Menu item 003 BAND/AFC, as appropriate.

Broadcast: Set to 000.

HRC: Set to 002.

CATV: Set to 001 (default).

IRC: Set to 003.

4. Set Installer Menu item 027 HOSPITAL MODE, as appropriate, to select the speaker configuration.

5. Set any other Installer Menu items that affect your TV programming network to the required configuration. For example, enable/disable Aux inputs, set a Start Channel, etc.

6. After you have adjusted all Installer Menu item settings as required, press OK (Enter) once on the Installer Remote to save your changes; then, press OK (Enter) again to exit the menu.

xxLQ630H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ 000

UPN 000-000-000-000

PTC V1.00.013

CHANNEL

ASIC D279

CPU V3.07.00

Typical Installer Menu

Note: The Installer Menu header will vary depending on the TV you are setting up.

117 FACT DEFAULT 000

003 BAND/AFC 001

027 HOSPITAL MODE 254

Adjust the values for these

Installer Menu items.

• Auto Tuning

• Manual Tuning

• Channel Edit

• Channel Label

Move Enter

Run Auto Tuning (Channel Search)

Note: In the FTG Configuration file, Logical Channel numbers will automatically be assigned in ascending order, starting with 0 (zero), to the Physical

Channels from the TV Channel Map.

Note: Pro:Idiom decryption for encrypted channels will not be enabled unless you use the FTG File Manager to set the channel attributes.

1. Search for all available analog and digital channels: Use the Installer

Remote to go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.

2. Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only. Add/delete channels per your system requirements.

Once you have completed these procedures, return to “Learning an FTG Configuration

File from a TV” on the previous page to complete the Learn sequence.

Use Channel Menu options to run Auto Tuning and edit the channel lineup, as necessary.

206-4207

47

FTG Mode via EBL (Local Configuration)

The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV connection. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for further information.

Notes:

FTG Device Configuration Application software is available online at: www.LGsolutions.com/ ftgsoftware.

If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the

FTG Channel Map and FTG Installer Menu settings. Instead, refer to and use the processes described on pages 43 to 45 to reconfigure the TV CPU.

If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information before proceeding.

22LQ630H

Jack Panel

UPDATE

1. Install (if necessary) and launch the FTG Device

Configuration Application (v5.0.0 or higher) on the

PC that will be used to configure the EBL.

2. Build an FTG Channel Map using the FTG Channel

Map Editor in the FTG Channel Map Configuration

Utility (or, if applicable, open an existing FTG

Configuration [.rml] file).

Note: Up to 141 logical channels can be defined in the FTG Channel Map.

3. Connect the PC to the TV-LINK CFG jack on the

TV’s rear connections panel using a USB-to-TTL serial cable (TTL-232R-5V-AJ). If necessary, install the device driver on the PC.

4. Turn ON the TV.

Note: If Installer Menu item 118 POWER SAVINGS is set to 3 (default), the TV must be ON in order for steps 5 and 6 below to be successful.

5. “Write” the FTG Channel Map to the EBL (switches the EBL from Pass-through Mode to FTG Mode).

Note: After a “Write” of new data, the TV will briefly display a green text banner that shows the EBL firmware version and release date.

6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu Configuration

Utility. If necessary to make changes to Installer

Menu items, “Write” them back to the EBL in FTG

Mode.

7. Save the FTG Channel Map and FTG Installer

Menu settings to an FTG Configuration (.rml) file for future use.

8. Tune the TV to a logical channel in the FTG

Channel Map.

PILLOW SPEAKER

RGB IN (PC)

PILLOW SPEAKER

GAME CONTROL

/ MPI

UPDATE

1

..........

/DVI IN IN

1

1

..........

/DVI

..........

RGB IN (PC)

IN

/DVI IN

2

2

..........

IN

..........

IN

AUDIO IN

(RGB/DVI)

SPEAKER

OUT(8Ω)

GAME CONTROL

/ MPI

TV-LINK

TV-LINK

CFG

26/32LQ630H

Jack Panel

ANTENNA IN

ANTENNA IN

ANTENNA IN

42CQ610H

Jack Panel

RESET UPDATE

RESET UPDATE

PTC SERVICE

(SERVICE ONLY)

PTC SERVICE

(SERVICE ONLY)

SPEAKER OUT

SPEAKER OUT

AUDIO IN

(RGB/DVI)

RS-232C IN

(SERVICE ONLY)

AUDIO IN

(RGB/DVI)

(RGB/DVI)

(SERVICE ONLY)

CPU SERVICE

RS-232C IN

(SERVICE ONLY)

(SERVICE ONLY)

TV-LINK

CFG

TV-LINK

CFG

TV-LINK

CFG

TV-LINK CFG

USB-to-TTL Serial Cable

TV-LINK CFG

USB-to-TTL Serial Cable

TV-LINK CFG

USB-to-TTL Serial Cable

48

Laptop

PC

Laptop

PC

Laptop

PC

Laptop

PC

Laptop

PC

PC

Laptop

PC

Laptop

PC

PC

206-4207

FTG File Manager Utilities Overview

FTG File Manager Main Screen

FTG CONFIGURATION LIST

Data to be saved in FTG

Configuration (.tlx) file.

Filename of opened FTG

Configuration (.rml) file created using FTG Device

Configuration Application.

Copy FTG Channel Map to and from FTG

Configuration List.

Copy FTG Installer Menu settings to and from FTG

Configuration List.

Load default FTG Installer

Menu for appropriate

LQ630H chassis or

42CQ610H chassis.

CLEAR/SAVE

FTG Configuration

List options.

NEW/OPEN

TLX File options.

TV SETUP MENU LIST

Data to be saved in FTG

Configuration file.

TLX FILE CONTENTS

Data contained in opened

FTG Configuration (.tlx) file.

Note: The data referenced in the FTG Configuration List is only a snapshot of the current FTG Channel Map and FTG Installer Menu settings when copied to the list. If you make any change(s) to the current data to be included in the FTG Configuration List, you will need to recopy

Channel Map and Installer Menu settings to the FTG Configuration List.

206-4207

49

FTG File Manager Utilities Overview (Cont.)

FTG Channel Map Configuration Utility

The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical

Channel Map.

50

Filename of opened FTG

Configuration (.rml) file created using FTG Device Configuration

Application.

EDIT/ADD MAP

Click to open the FTG

Channel Map Editor to create or edit an FTG Channel Map

(see next page).

PRINT MAP

Click to display a printable

FTG Channel Map Report. The report can also be exported as an HTML or Text file.

206-4207

FTG File Manager Utilities Overview (Cont.)

FTG Channel Map Editor

The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map.

LOGICAL CHANNEL MAPPING

Select a Logical Channel number. Then, assign it the RF, Major, and Minor channel numbers to complete the mapping.

CUSTOM CHANNEL LABELS/ICONS

Enter custom labels and select icons by name on menu or by number.

SET CHANNEL ATTRIBUTES

Check/select Encrypted, OSD, or Blank Video.

ZONE RESTRICTION

Select Zone restriction for channel. See

Reference section, “TV

Zone Restrictions,” for further information.

206-4207

ADD

After defining a new

Logical Channel, click to add channel to the FTG

Channel Map.

UPDATE

After editing an existing

Logical Channel’s data, click to commit the changes in the FTG Channel Map.

EXIT

Click to exit editor and return to FTG Channel

Map Configuration Utility.

DELETE

Click to remove highlighted channel from FTG Channel

Map.

51

FTG File Manager Utilities Overview (Cont.)

FTG Installer Menu Configuration Utility

CONFIGURATION SETTINGS

Select tabs for categories of Installer

Menu items to set up TV.

52

Filename of opened FTG Configuration

(.rml) file created using FTG Device

Configuration Application.

Note: The Pro:Centric tab enables you to set up Pro:Centric-specific parameters. Refer to the Free-To-Guest (FTG) File Manager User Guide for further information.

206-4207

Reference: Upgrading TV/PTC Software using a USB Memory Device

Checking the Software Versions

You can check the software versions of the TV by accessing the Installer Menu with the Installer

Remote: Press MENU repeatedly until the on-screen menu display no longer toggles, and then, press

9-8-7-6 + OK (Enter).

When you are finished, press

OK (Enter) again to exit the Installer Menu.

xxLQ630H PTC INSTALLER MENU

CPU-CTV

000 INSTALLER SEQ 000

UPN 000-000-000-000

PTC V1.00.013

ASIC D279

CPU V3.07.00

PTC Version CPU Version

Typical Installer

Menu

Upgrading TV/PTC Software

Before you begin, note that the software upgrade files must be stored in a folder named “LG_DTV” in the root directory of the USB memory device. Also, ensure the USB device has been formatted with FAT format.

Note for TV Software Upgrade only:

If the TV detects a later version of software on the USB device, it will automatically display a dialog from which you can start the software upgrade immediately. Otherwise, you can close the dialog, and access the

USB Download Menu as described below.

TV Software Update (Expert)

1. Turn the TV ON.

2. Plug the USB memory device into the USB IN port on the TV.

3. Press MENU on the Installer Remote to display the TV setup menus (TV is in

Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).

4. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu.

Then, press the number “ 7” key a total of seven times to display the USB

Download Menu.

5. Use the Up/Down arrow keys to select Upgrade TV Software or Upgrade

PTC Software, as applicable, and then press OK (Enter).

6. Select the appropriate option(s), depending on the type of upgrade:

• TV Software Upgrade: (See screen samples at right.) Select

TV Software

Update from the first TV Software Update window. In the second TV Software

Update window, select/highlight the update file to install and press OK (Enter).

Note: Do not select Forced Update options unless you have been specifically instructed to do so or have previous experience with Expert Software Updates.

• PTC Software Upgrade: In the PTC Software Update window, select/highlight the update file to install and press OK (Enter).

TV Software Update

Note: The PTC Software Update window is similar to the second TV Software

Update window. Current software version information is shown at the top and update files on the USB device are listed at the bottom of the window.

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Previous Enter

TV Software Update (Expert)

TV Software Update (Expert)

The following software files are found in the memory card.

Select the file you want to download to this TV or press EXIT to cancel the update.

TV Software Update

Splash.jpg

LOGO Image Download

TV Software Update (Expert)

TV Software Update (Expert)

[ Current TV Software Version Information ]

EPK : 01.26.00

The following software files are found in the memory card.

Select the file you want to download to this TV or press EXIT to cancel the update.

EPK :

[ Forced Update Option ]

SPI Boot

The TV will show update completion progress in a new window. Do NOT remove the USB device until the software upgrade is complete. When a TV software upgrade is complete, the TV will reset itself with an automatic restart. When a PTC upgrade is complete, the TV will turn OFF.

Upgrade PTC Software

TXT : V1.00.06

206-4207

The following software files are found in the memory card.

53

[ Forced Update Option ]

Ext. MICOM

LOGO Image xxLQ630H_v1.00.07

SPI Boot

TV Software Update (Expert)

The following software files are found in the memory card.

Select the file you want to download to this TV or press EXIT to cancel the update.

Splash.jpg

TV Software Update (Expert)

[ Current TV Software Version Information ]

EPK : 01.26.00

The following software files are found in the memory card.

Select the file you want to download to this TV or press EXIT to cancel the update.

EPK :

[ Forced Update Option ]

SPI Boot

LOGO Image xxLQ630H_v1_27_00_USB

Upgrade PTC Software

TXT : V1.00.06

The following software files are found in the memory card.

[ Forced Update Option ]

Ext. MICOM

LOGO Image xxLQ630H_v1.00.07

SPI Boot

Reference: Downloading a Splash Screen using a USB Memory Device

Splash Screen Image File Guidelines

The splash screen image must be a baseline (not progressive) 24-bit

JPEG.

The image should be no larger than 1 MB.

The ideal resolution of an image for the 26/32LQ630H is 1366 x 768 pixels (HD) or under and for the 22LQ630H is 1920 x 1080 pixels

(FHD) or under.

The ideal resolution of an image for the 42CQ610H is 1920 x 1080 pixels (FHD) or under.

TV Software Update (Expert)

The image file must be stored in a folder named “LG_DTV” in the root directory of USB memory device.

Ensure the USB device has been formatted with FAT format.

Downloading a Splash Screen Image

1. Turn the TV ON.

3. Press MENU on the Installer Remote to display the TV setup menus

(TV is in Pass-through Mode) or the Function Menu (TV is not in

Pass-through Mode).

LOGO Image Download

4. Use the arrow navigation keys to select/highlight either the menu icon from the TV setup menus or the

Option

Lock menu icon from the

Function Menu; then, press the number “ 7” key a total of seven times to display the USB Download Menu.

5. Use the Up/Down arrow keys to select Upgrade TV Software, and then press OK (Enter).

6. Use the Up/Down arrow keys to select the image file to download, and then press OK (Enter).

TV Software Update

The TV will show download completion progress in a new window. Do

NOT remove the USB device until the image download is complete.

When the image download is complete, the TV will reset itself with an automatic restart. Upon the restart, you should see the new splash screen.

54

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (TLX)

Previous

TV Software Update (Expert)

Enter

The following software files are found in the memory card.

Select the file you want to download to this TV or press EXIT to cancel the update.

Splash.jpg

TV Software Update (Expert)

[ Current TV Software Version Information ]

EPK : 01.26.00

The following software files are found in the memory card.

Select the file you want to download to this TV or press EXIT to cancel the update.

EPK :

[ Forced Update Option ]

SPI Boot

LOGO Image xxLQ630H_v1_27_00_USB

Upgrade PTC Software

TXT : V1.00.06

The following software files are found in the memory card.

[ Forced Update Option ]

Ext. MICOM

LOGO Image xxLQ630H_v1.00.07

SPI Boot

206-4207

Reference: Power Consumption Settings

The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 3 (default) and

Installer Menu item 099 BACK LIGHTING is set as shown below (default value for LQ630H TVs is

255; default value for CQ610H TVs is 100).

100

50

40

30

20

10

1

90

80

70

60

Item 099

Back Lighting

(Static)

22LQ630H

Power

Consumption

(Watts)

23.0

22.4

21.6

21.0

20.3

19.5

18.8

18.1

17.4

16.7

16.0

Percent

Savings

0.0%

3.5%

6.5%

8.7%

11.7%

15.2%

18.3%

21.7%

24.8%

27.4%

30.4%

26LQ630H

Power

Consumption

(Watts)

35.1

33.2

31.5

29.7

27.9

26.2

24.5

22.7

20.9

19.2

17.7

Percent

Savings

0.0%

5.4%

10.3%

15.4%

20.5%

25.4%

30.2%

35.3%

40.5%

45.3%

49.6%

32LQ630H

Power

Consumption

(Watts)

50.0

46.8

44.0

40.7

37.7

34.6

31.5

28.7

25.5

22.4

19.5

Percent

Savings

0.0%

6.4%

12.0%

18.6%

24.6%

30.8%

37.0%

42.6%

49.0%

55.2%

61.0%

42CQ610H

Power

Consumption

(Watts)

111.6

105.8

95.0

89.0

84.5

75.0

67.0

60.1

53.1

45.8

39.4

Percent

Savings

0.0%

5.2%

14.9%

20.3%

24.3%

32.8%

40.0%

46.1%

52.4%

59.0%

64.7%

200

150

140

130

120

110

101

190

180

170

160

Item 099

Back Lighting

(Dynamic)

22LQ630H

Power

Consumption

(Watts)

22.3

21.6

20.9

20.2

19.6

18.9

18.2

17.4

17.1

16.5

16.0

Percent

Savings

0.0%

3.1%

6.3%

9.4%

12.1%

15.2%

18.4%

22.0%

23.3%

26.0%

28.3%

26LQ630H

Power

Consumption

(Watts)

34.0

32.3

30.6

29.5

27.7

26.1

24.3

22.5

20.8

19.1

17.6

Percent

Savings

0.0%

5.0%

10.0%

13.2%

18.5%

23.2%

28.5%

33.8%

38.8%

43.8%

48.2%

32LQ630H

Power

Consumption

(Watts)

47.0

44.1

41.7

38.7

35.9

33.0

30.3

27.9

25.2

22.3

19.3

Percent

Savings

0.0%

6.2%

11.3%

17.7%

23.6%

29.8%

35.5%

40.6%

46.4%

52.6%

58.9%

42CQ610H

Power

Consumption

(Watts)

107.0

102.0

92.0

87.0

83.0

75.0

67.4

60.1

53.2

45.7

39.0

Percent

Savings

0.0%

4.7%

14.0%

18.7%

22.4%

29.9%

37.0%

43.8%

50.3%

57.3%

63.6%

Note: Values are results of controlled experiments under laboratory conditions.

206-4207

55

Reference: TV Aux Input Configuration

DIRECT ACCESS

Tuning

OLD_

OCV = 0

131

132

133

OLD_

OCV = 1

91

92

93

134 94

Source

Input

Video1

(Rear)

HDMI2

HDMI1/

DVI

RGB

TV

Source

Mode

CV/

SVIDEO

DTV/PC

DTV/PC

PC

Number

Installer Menu

ENABLE

Labeling

MPI DATA

STATUS TYPE

0x41 SOURCES

ENABLED (R/W)

Value Labeling

39

91

35

87

REAR AUX EN

YPrPb2 EN

COMPPORT EN

REAR RGB EN

0x02

Rear Video

(Aux)

0x04 S-Video Rear

0x08

0x10

Front

Computer

SVGA Rear

Computer

MPI DATA

DATA STATUS

TYPE 0xD2

CURRENT AV

SOURCE (R)

Value Labeling

DATA STATUS

TYPE 0x0D

AUX

SOURCE (R)

1

2

3

4

Rear Video

(Aux)

S-Video Rear

Front

Computer

SVGA Rear

Computer

0 (VIDEO)

0 (VIDEO)

0 (VIDEO)

2

(COMPUTER)

START AUX

SOURCE

ASSIGN-

MENT

1

5

3

4

56

206-4207

Reference: b-LAN Setup & Overview

The b-LAN module is internal to the TV. It allows hospital/institution head end equipment with b-LAN technology to communicate, via the institution’s RF distribution system, with the TV for configuration and control.

Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port. The default value is 003—the b-LAN module as well as the

GAME CONTROL/MPI port circuitry is only powered when the TV is turned ON. See chart below.

POWER

SAVINGS

001

003 (default)

TV Standby State

b-LAN & GAME

CONTROL/MPI Port

Power

On

Off

TV Power On State

b-LAN & GAME

CONTROL/MPI Port

Power

On

On

A b-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded b-LAN module to receive communication from the head end device. At this point, if it is desired for the b-LAN module to always be powered, including while the TV is in Standby, set Installer

Menu item 118 POWER SAVINGS to 001.

Also, if MPI communication is required for external MPI control, set Installer Menu item 118 POWER

SAVINGS to 001 so that the GAME CONTROL/MPI port circuitry is always powered.

206-4207

57

Reference: LQ630H/CQ610H Hospital Operations

Hospital Features

The following table identifies when and how the LQ630H and CQ610H hospital features are supported in three different TV configurations. As indicated in the introduction to this document, LG commercial TV functionality is based on “ownership” of the Channel Map. For the purposes of this table, “CPU” indicates that the TV is in Pass-through Mode with the Channel Map in the CPU (i.e., auto-tuned/edited Channel

Map) and “PTC” indicates that the TV is in Pass-through Mode with the Channel Map in the PTC (i.e., after

2-5-5 + MENU).

Disabled

CPU

Enabled Disabled

PTC

Enabled

FTG/PPV Mode

Disabled Enabled Hospital Mode State

Installer Menu

IR Banks Enable

Scan Mode

Start Channel in Scan Mode

Feature Level

Bed 1/Bed 2

Multi-code IR

Speaker

Function Preview

Hospital Mode

Bed 1/Bed 2

Pillow Speaker Voltage

Speaker

Quick Shutoff

Item

025

027

027

027

027

077

012

013

014

020

020

020

020

(a)

X

X

(b)

X

(c)

(a)

X

X

X

X

(c)

X

X

X

X

X

X

(b)

(c)

X

X

X

(c)

X

X

X

X

X

X

X

X

(b)

X

X

X

X

Channel Banks

Number of Banks Enabled

Channel Preview/Banks Setup Menu

Blanked Channel

Inactive TV

SAP Key

1

X

X

4

X

X

X

X

X X

Aux Input Sources

Input List Menu

Aux in Scan List

X X X

X X

X

(d)

TV Setup Menus

Audio (TV Speaker)

Option (Power Indicator)

X = feature supported

(e)

X

(e)

X

(e)

X

(e)

X a) Turn ON function only. Always goes to channel 2-0.

b) Defaults to Zenith pillow speaker code/(+12v) supply voltage.

c) Quick Shutoff feature only functions when Scan Mode is enabled and if you are using an analog pillow speaker.

d) Dependent upon installer-defined Logical Channel Map.

e) Audio Menu is only accessible when the speaker selected is TV Only or both TV & Pillow.

X

(d)

58

206-4207

Reference: LQ630H/CQ610H Hospital Operations (Cont.)

Note: Even if Scan Mode is enabled, the front panel channel keys cannot be used to turn ON the TV.

Note: The power indicator on the front panel of the TV has two different settings: one for when the TV is in standby and one for when the TV is turned ON. The Power Indicator option in the Option Menu enables you to define the behavior of the power indicator. For LQ630H TVs, the Standby Light default is OFF, while the Power Light default is ON. Note, however, if an LQ630H TV is in the default Hospital Mode, it is not possible to change the Power Indicator settings. This means that for LQ630H TVs, when Installer Menu

Item 027 HOSPITAL MODE is set to 254, the power indicator will retain its default settings regardless of any changes made via the Power Indicator option in the Option Menu. For CQ610H TVs, both the Standby

Light and Power Light defaults are ON, and the Power Indicator settings are not affected by the Hospital

Mode.

Speaker Selection

The following table outlines speaker settings as determined by Installer Menu items 027 HOSPITAL

MODE and 020 FEATURE LEVEL.

Item 027 HOSPITAL

MODE Value

0

0

0

1

~

34

65

~

98

65

~

98

129

~

162

129

~

162

Item 020 FEATURE

LEVEL Value

0

~

24

0

~

24

64

~

65

N/A

N/A

N/A

N/A

N/A

Audio Menu

TV Speaker

OFF

ON

N/A

N/A

OFF

ON

OFF

ON

Speaker

None

TV Only

Pillow Only

Pillow Only

None

TV Only

Pillow Only

Pillow & TV

Note: If the TV is in FTG Mode, the Audio Menu is no longer accessible.

206-4207

59

Reference: Resetting Factory Defaults on the TV(s)

This section describes how to reset factory defaults either on a single TV that is currently in Pass-through or FTG Mode or on multiple TVs that are currently in FTG Mode.

Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Passthrough Mode.

Installer Menu Item 117 FACT DEFAULT

If the TV is currently in Pass-through Mode, you can set Installer Menu item 117 FACT DEFAULT to 001 to reload the factory defaults and clear the channel lineup, including any assigned channel icons and custom text labels.

Factory “IN-STOP”

If the TV is currently in FTG Mode, a predefined value for Installer Menu item 117 FACT DEFAULT enables access to initiate a factory “IN-STOP” process that will reset the TV to Pass-through Mode in addition to restoring all factory defaults. Contact technical support for the required value for Installer Menu item 117 and for additional information on performing the IN-STOP from the Installer Menu.

Additional FTG Mode via CPU Options

There are two additional options for resetting Pass-through Mode/factory defaults on TVs that are in FTG

Mode via the CPU. The first enables you to reset a single TV to Pass-through Mode, while the second enables you to reset multiple TVs to Pass-through Mode at one time.

Using a USB memory device, “Teach” an FTG Configuration (.tlx) file that only contains a “Zero

Mapped Channels” FTG Channel Map to the TV. Refer to “Creating an FTG Configuration File using the

FTG File Manager” and “Teaching FTG Configuration to a TV” on pages 43 to 45 for further information.

If your system uses a Pro:Centric server for remote management/administration, use the Pro:Centric

Admin Client to load an FTG Configuration (.tlx) file that only contains a “Zero Mapped Channels” FTG

Channel Map on the Pro:Centric server. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.

Additional FTG Mode via EBL Options

There are two additional options for resetting Pass-through Mode/factory defaults on TVs that are in FTG

Mode via the EBL. The first enables you to reset a single TV to Pass-through Mode, while the second enables you to reset multiple TVs to Pass-through Mode at one time.

Note: While the IN-STOP process described above will clear both the PTC and the CPU, both options below only clear the PTC. Thus, the current Channel Map and TV setup menu settings will remain in the CPU after the reset is completed.

Using a direct PC-to-TV connection, “Write” an unpopulated Channel Map—that is, a Channel Map with zero channels—to the TV. Refer to the “FTG Mode via EBL” procedure on page 48 and/or the Free-To-

Guest (FTG) Device Configuration Application User Guide for further information.

If your system uses an FMA for remote management/broadcast configuration, configure the FMA device with an FMA Configuration file that only contains a “Zero Mapped Channels” FTG Channel Map to broadcast to the TV EBL(s). Refer to the Free-To-Guest (FTG) Device Configuration Application

User Guide and/or the Installation & Configuration Guide for the FMA device for further information.

60

206-4207

Reference: TV Zone Restrictions

The FTG Channel Map Editor in the FTG File Manager’s FTG Channel Map Configuration Utility enables you to assign Zone restrictions to channels that may be deemed unsuitable for certain locations, for example, a hotel lobby. In the FTG Channel Map Editor, a Zone # (for example, “1”) must be designated for each channel that is to be restricted.

On location, set the Zone # for all the TVs in a select area, or “Zone” (for example, the lobby) so that the

TVs can omit channels that have been restricted in the FTG Channel Map. However, note that while a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. TV Zone 0 is the default TV Zone #. When the TV Zone is 0, the TV will ignore any restriction that may be placed on channels in the FTG Channel Map.

See the FTG Channel Map Editor overview on page 51. Also, see the Free-To-Guest (FTG) File Manager

User Guide for more detailed information on assigning Zone restrictions.

Use the following procedure to specify a Zone designation for a

TV. Note that the Zone can only be set while the TV is in Passthrough Mode.

1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the OPTION menu option.

Then, press OK (Enter).

2. Use the Up/Down arrows to select

Zone, and then press OK

(Enter).

3. In the Zone pop-up window, use the Left/Right arrows to select the appropriate Zone number. Then, press OK (Enter).

4. Press MENU to return to TV viewing.

OPTION

• Language

• Caption

• Power Indicator

• Set ID

• Demo Mode

• Zone

• Eject

: Off

: 1

: Off

: 0

Move

1

Close

Enter

206-4207

61

Reference: 22LQ630H Rear and Side Jack Panels

USB IN

Insert USB memory device for software updates, cloning purposes, FTG Mode via

CPU configuration, picture/ music entertainment, etc., as applicable.

62

PILLOW SPEAKER

Connect pillow speaker here.

PILLOW SPEAKER

PILLOW SPEAKER

1

..........

/DVI IN

2

..........

IN

1

..........

/DVI IN

2

..........

IN

RGB IN (PC)

Connection for RGB output from PC.

RGB IN (PC)

HDMI/DVI IN

Connection for HDMI/

DVI output from external device.

UPDATE

RESET

AUDIO/VIDEO IN

Connect to video/audio output port on external device (use A/V adapter cable provided with TV).

AUDIO IN (RGB/DVI)

Audio connection for

RGB or DVI device.

UPDATE

RESET

AUDIO IN

TV-LINK

/ MPI

TV-LINK

AV IN

AUDIO/VIDEO

UPDATE

Restricted to software updates.

RESET

Initiates a hardware reset and switches the TV to standby.

SPEAKER OUT (8Ω)

*

Connect to 8 ohm self-powered speaker input. Intended for special applications, such as a powered bathroom speaker with volume control.

CPU SERVICE (SERVICE ONLY)

Restricted to CPU service updates.

ANTENNA IN

Connect to Antenna/CATV.

PTC SERVICE (SERVICE ONLY)

Restricted to PTC service updates.

TV-LINK CFG

Use for direct PC-to-TV FTG configuration.

GAME CONTROL/MPI

When the TV/EBL is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., clone programmer, VOD/PPV STB, etc.) to control the

TV. Game Control—EBL in LodgeNet PPV Mode only.

*

This stereo jack provides a mono speaker fixed-level,

1 watt output (audio +, audio -, w/ground shield). Do NOT plug in a mono connector, as this may damage the TV.

206-4207

Reference: 26/32LQ630H Rear and Side Jack Panels

RESET

Initiates a hardware reset and switches the TV to standby.

ANTENNA IN

UPDATE

Restricted to software updates.

USB IN

Insert USB memory device for software updates, cloning purposes, FTG Mode via CPU configuration, picture/music

ANTENNA IN

ANTENNA IN

ANTENNA IN

Connect to

Antenna/CATV.

PTC SERVICE (SERVICE ONLY)

Restricted to PTC service updates.

CPU SERVICE (SERVICE ONLY)

Restricted to CPU service updates.

RESET

UPDATE

RESET

UPDATE

*

This stereo jack provides a mono speaker fixed-level,

1 watt output (audio +, audio -, w/ground shield). Do NOT plug in a mono connector, as this may damage the TV.

206-4207

AUDIO IN (RGB/DVI)

AUDIO IN (RGB/DVI)

AUDIO IN (RGB/DVI)

Audio connection for RGB or DVI device.

USB IN

Insert USB memory device for software updates, cloning purposes, FTG Mode via CPU configuration, picture/music entertainment, etc., as applicable.

RGB IN (PC)

Connection for RGB output from PC.

HDMI/DVI IN

Connection for HDMI/DVI output from external device.

AUDIO/VIDEO IN

Connect to video/audio output port on external device (use A/V adapter cable provided with TV).

RESET

UPDATE

PILLOW SPEAKER

GAME CONTROL/MPI

When the TV/EBL is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., clone programmer, VOD/PPV STB, etc.) to control the

TV. Game Control—EBL in LodgeNet PPV Mode only.

PILLOW SPEAKER

PILLOW SPEAKER INPUT

Connect pillow speaker here.

PILLOW SPEAKER

SPEAKER OUT (8Ω)

*

Connect to 8 ohm self-powered speaker input.

Intended for special applications, such as a powered bathroom speaker with volume control.

TV-LINK CFG

Use for direct PC-to-TV FTG configuration.

63

Reference: 42CQ610H Rear and Side Jack Panels

USB IN

Insert USB memory device for software updates, cloning purposes, FTG Mode via

CPU configuration, picture/ music entertainment, etc., as applicable.

AV IN

AUDIO/VIDEO IN

L/MONO-AUDIO-R IN

Connect to audio output jacks on external device.

For only mono audio output, connect to Left audio input.

ANTENNA IN

Connect to

Antenna/CATV.

ANTENNA IN

AV IN

VIDEO IN

Connect to video output port on external device.

HDMI 2

HDMI

/DVI IN

1

PILLOW SPEAKER

Connect pillow speaker here.

HDMI/DVI IN

Connection for HDMI/DVI

..........

..........

HDMI 2

HDMI

/DVI IN

1

RESET UPDATE

PTC SERVICE

(SERVICE ONLY)

SPEAKER OUT

RESET UPDATE

PTC SERVICE

(SERVICE ONLY)

SPEAKER OUT

RESET UPDATE

RGB IN (PC)

PTC SERVICE

(SERVICE ONLY)

SPEAKER OUT

RESET

AV IN

Initiates a hardware reset and switches the TV to standby.

RS-232C IN

(SERVICE ONLY)

UPDATE

Restricted to software updates.

TV-LINK

CFG

SPEAKER OUT (8Ω) *

Connect to 8 ohm self-powered speaker input. Intended for special applications, such as a powered bathroom speaker with volume control.

PILLOW SPEAKER

..........

RGB IN (PC)

RS-232C IN

(SERVICE ONLY)

TV-LINK

CFG

PTC SERVICE (SERVICE ONLY)

Restricted to PTC service updates.

GAME

MPI

RGB IN (PC)

RS-232C IN

(SERVICE ONLY)

TV-LINK CFG

Use for direct PC-to-TV FTG configuration.

RS-232C IN

Use for downloading software updates, etc.

AUDIO IN (RGB/DVI)

Audio connection for RGB or DVI device.

RGB IN (PC)

Connection for RGB output from PC.

GAME CONTROL/MPI

When the TV/EBL is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., clone programmer, VOD/PPV STB, etc.) to control the

TV. Game Control—EBL in LodgeNet PPV Mode only.

*

This stereo jack provides a mono speaker fixed-level, 1 watt output

(audio +, audio -, w/ground shield).

Do NOT plug in a mono connector, as this may damage the TV.

64

206-4207

Reference: Pillow Speaker Setup

The pillow speaker will only be functional after the Express Script/Custom Master TV Setup and cloning procedures are complete.

Note: When Installer Menu item 027 HOSPITAL MODE is set to 254 (factory default value), there is no power (voltage) supplied to the pillow speaker.

Connect a Pillow Speaker to the LCD TV

Connect the pillow speaker (see example at right) to the PILLOW

SPEAKER interface on the rear jack panel of the TV.

Caution: Use a pillow speaker that is a UL recognized pendant control bearing the warning: “Risk of fire if used in oxygen enriched atmosphere. Keep pendant control away from oxygen equipment.”

Typical Pillow Speaker

(Serial Data Control)

Controlling the TV with Serial Data

These TV models are capable of being controlled by a single-wire, serial data signal. This is an LG patented technology and is being implemented by certain brands of “smart” pillow speakers.

Pillow Speaker Interface

This connector provides an interface for patient-pendant remote control or entertainment audio and nurse call systems. All lines are isolated from the AC power line. (Optoisolators isolate the control lines, and a transformer isolates the audio.) Earth ground is provided on pin 4

(Common) in the default configuration (e.g., for Zenith/Philips pillow speakers). For negative voltage configuration (e.g., for RCA pillow speakers), +5 volts is provided on pin 4 (Common), with pin 3 (Channel

Up/Data In) referenced to ground.

The following table describes the pillow speaker interface pinout (see also diagram at right).

3

4

Pin No.

Description

1 Analog external control for TV ON/OFF.

2 No connection

5

Analog external control for Channel Up or Serial Data In.

Common connection for control, data, and audio output.

6

Isolated Audio Output. Nominal 14 ohm source impedance with short circuit protection. Intended for a pillow speaker with a lowimpedance, pad-type volume control.

Analog external control for Channel Down.

PILLOW SPEAKER

Pillow Speaker Interface Pinout

5

1

4

6

2

3

5

6

3

4

1

2

Typical Schematic for

Analog Pillow Speaker

CHANNEL

PREV

SLEEP

VOLUME

MUTE

OPTION

TV ON/OFF

NC

CHAN UP/DATA IN

COMMON

AUDIO OUT

CHAN DOWN

Controlling the TV with Mechanical Switches

A typical analog pillow speaker with mechanical switches will momentarily connect pin 1, 3, or 6 to pin 4 (Common) to control Power ON/OFF,

Channel Up, or Channel Down (see schematic at right). These pins are at

+13 volts DC (when measured from pin 4) with the switches open. Typical current draw is 8 mA when a switch is closed. (This operation is identical to previous models using the 5-wire interface, except that only +7 volts

DC was supplied and current draw was only 2.5 mA.)

SPKR

VOLUME CONTROL

TV

ON/OFF

CHAN

DOWN

5

1

4

6

2

3

(MALE

PLUG)

CHAN

UP

206-4207

65

Reference: USB Media Navigation using Pro:Centric Pillow Speaker

The Pro:Centric pillow speaker is currently the only pillow speaker that enables users to navigate and play/view USB media files (videos, music, photos, etc.). This section provides a brief overview of the Pro:Centric pillow speaker navigation tools.

Note: Refer to the Owner’s Manual for detailed information on USB memory device requirements and the types of media supported by the LQ630H and CQ610H TVs.

1. Plug the USB memory device into the TV’s USB IN port.

Once the TV detects the USB device, the Media Menu will be displayed on the TV screen. (The actual menu header shown on the TV screen will reflect the name of your

USB device.)

USB MEDIA

Movie List Photo List Music List

Note: If you press the Return button on the pillow speaker, this will exit the Media Menu. If you wish to redisplay the menu, you must physically remove and then reinsert the USB memory device. It is not possible to display the Media Menu using the pillow speaker alone.

2. Use the arrow keys on the pillow speaker to select/highlight the desired menu option, and then press Enter.

3. Within each USB media directory (Movie List, Photo List, or Music List):

• Use the arrow keys on the pillow speaker to navigate from one folder or file to another, and press Enter to open or play a selected folder or file.

• If there are multiple pages of folders and/or files, use Channel Up/Down on the pillow speaker to move between the pages. At the top right corner of the display, a “Page” indicator will identify the number of pages available in the current directory.

• Additional menu options are listed at the bottom of the display (each corresponds to a number button on the pillow speaker). These typically enable you to change directories, change the number of thumbnails shown at one time, mark files (to add to play lists), etc.

Note: To exit the Media Menu from any of the three USB media directories, press 0 on the pillow speaker. If you wish to redisplay the Media Menu, you must physically remove and then reinsert the USB memory device.

• In View and Play modes, you typically can use the pillow speaker to navigate to another directory level (without exiting the Media Menu).

• To exit the directory/Media Menu entirely, either press 0 or Return on the pillow speaker.

Refer to the Owner’s Manual for additional information on the Media Menu and directory options.

POWER

GUIDE

PORTAL

ENTER

INFO

RETURN

CHANNEL

MUTE

VOLUME

Typical Pro:Centric

Pillow Speaker

66

206-4207

General Guidelines: Choosing a Location for Installing a VESA Standard Mount

To the right are some examples of VESA standard mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instructions provided with the TV stand that will be used to mount the TV. Be sure the style of stand selected is capable of supporting the weight of the TV and is appropriate for the application.

Wall Mounts

If the mount will be on a wall, a typical wooden stud behind the wall board would be the preferred choice for a location to attach the wall mount. The wall mount location chosen should be appropriate for drilling holes and have available the required power source as well as antenna/cable and any other equipment leads as necessary.

Pedestal Mounts and Stands

A sturdy surface on a desk or other similar flat table-like furniture would be the appropriate location for mounting a pedestal-style TV stand.

Most stands are designed so that the wiring is threaded through the stand itself or a loopthrough style clamp so that the wiring is neatly bunched and not strung in such a way as to create a potential hazard to the user.

(Some stands are portable and can be moved from one location to another.) Be sure all safety considerations are followed.

Reference: VESA Standard TV Mounts

Typical Wall Stud Type Mount with

Swivel Bracket

Typical Pedestal Type Mount with

Swivel Bracket

206-4207

67

Troubleshooting

General Troubleshooting (Some Quick and Easy Tips for Resolving Problems)

Symptom

Installation

Cannot direct enter channel number.

No channels present after setup.

Possible Cause(s) Possible Solution(s)

(TV in Pass-through Mode) Installer

Menu item 028 CH. OVERIDE is set to 0, i.e., disabled and/or Channel

Access was denied in Express Script.

(TV in FTG Mode) The channel entered is not part of the FTG Channel

Map.

Auto Tuning (Channel Search) not run.

If the channel lineup is locked (recommended setting), only channels that are active in the TV’s channel lineup can be selected. Set 028 CH. OVERIDE to 1 to allow access for direct keypad entry to all channels.

Channel access is restricted to channels included in the FTG

Channel Map. If necessary, make changes to the FTG Channel

Map using the FTG File Manager or the FTG Device

Configuration Application, as appropriate.

Refer to Express Script or Custom Master TV Setup procedure, as appropriate. Auto Tuning must be run in order for the channel lineup to be populated. Note for Express Script: You must select

“Execute Auto Search” in the Auto Search screen to run the search (see page 13). To re-activate the Express Script, set

Installer Menu item 117 FACT DEFAULT to 001.

Power

No power.

See troubleshooting flow chart on following page.

Picture Reception and Sound

No picture.

TV is turned OFF.

Normal picture, poor or no sound.

• Turn TV ON.

• Power failure?

Connect antenna/cable signal to TV.

Check connections on TV.

If applicable, connect MPI cable to MPI device.

Try another channel.

Adjust Installer Menu settings.

Try a different channel.

Press MUTE or use Volume Up key to increase sound level.

Check that Installer Menu items 020 FEATURE LEVEL and 027

HOSPITAL MODE are set as required. Also, if applicable, select

TV Speaker in the Audio Menu.

Erratic Operation

Antenna/cable not connected.

Connections incorrect.

MPI not connected.

Encrypted program.

Wrong tuning band.

Broadcast problem.

Audio muted.

Pillow/TV speaker not configured properly.

Wrong Installer Menu settings.

Adjust Installer Menu settings as required.

Installer Menu setup.

Installer Remote

Remote doesn’t work.

Remote not in TV Mode.

Not aimed at IR remote sensor.

Remote too far from IR sensor.

MPI not connected.

IR path to TV’s receiver obstructed.

Weak batteries.

Wrong battery polarity.

Too much light in room.

Bed Switch set to wrong bed.

Wrong Installer Remote.

Use MODE key to select “TV”; puts remote into TV Mode.

Point remote at TV’s IR receiver on TV.

Move remote closer to TV’s IR receiver or darken room.

If applicable, connect MPI cable to MPI device.

Remove obstructions.

Replace batteries.

Check that “+” and “-” match in battery compartment.

Dim room light.

Set Bed Switch or update Installer Menu, as necessary.

Requires compatible Installer Remote. Contact your LG dealer.

68

206-4207

Troubleshooting (Cont.)

Troubleshooting Flow Chart

Controller

Quick Check

STATUS

LED on PTC

Board blinking?

Yes

No

TV connected to AC

Power?

Yes

Bad

TV

No

Plug into AC

Power outlet.

Cycle the power by removing and reconnecting the AC Power cord. Then, observe POWER LED on front of TV.

POWER

LED lit?

*

Yes

Press POWER on

Installer Remote.

No

Bad Analog or

Digital Board

TV turned ON?

No

Yes

Press VOLUME UP/

DOWN or MUTE key on Installer Remote.

Bad

TV

TV responded?

No

Yes

Press VOLUME UP/

DOWN or MUTE key on

User-supplied Remote.

Bad

TV

TV responded?

No

Bad

PPV Card

End

Yes

206-4207

* If the Power Indicator/Standby Light option in the Option Menu is set to OFF, the POWER LED will not remain lit. Continue to the next step. (See also note regarding power indicator on page 59.)

69

Troubleshooting (Cont.)

Commercial Mode Check / FTG Operation Troubleshooting

Commercial Mode Check

Use this flowchart to determine whether the TV is currently in Commercial Mode.

Press

POWER on

Installer Remote.

TV turned

ON?

Yes

No

TV connected to AC

Power?

Yes

Bad

TV

No

Plug into AC

Power outlet.

Leave the TV set ON, and press MENU on the

Installer Remote.

Function

Menu on display?

Yes

TV is in

Commercial Mode.

No

Press MENU repeatedly as if to access the

Installer Menu.

On-screen menu display no longer toggles?

Yes

TV is in

Commercial Mode.

No

TV is not in Commercial

Mode. Call Technical

Support for assistance.

FTG Operation Troubleshooting

The following table provides troubleshooting information for when the EBL is configured in the FTG Mode of operation.

Symptom

Communication Error

(“Communications

Timeout”)

Possible Cause(s)

Cable(s) not connected.

TV not powered.

TV not turned ON.

Wrong COM

(communication) port.

Solution(s)

Check and connect communication cables.

Check/connect the TV power cord.

TV needs to be turned ON (default setting of Installer Menu item 118 POWER SAVINGS).

In the FTG Device Configuration Application, select the correct COM port for the cable being used.

70

206-4207

Troubleshooting (Cont.)

Clone Programmer Troubleshooting

Caution: If the TV is in

LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port, as this will damage the clone programmer.

Reset Clone Programmer After Static Shock

After replacing exhausted batteries (LT2002 only), or if the clone programmer behaves strangely after a static shock:

TLL-1100A: Turn the TLL-1100A OFF and then ON.

LT2002: Use a paper clip or similar instrument inserted through the small hole marked RESET to activate the internal reset switch and restore normal operation.

After a reset, check the real-time clock setting. It may be necessary to reset the clone programmer clock from a TV containing the correct time.

Note: See also IMPORTANT CLONING INFORMATION on page 32.

Clone Programmer

Symptom

Clone copies setup in less than 30 seconds.

Possible Cause(s)

Not enough time to copy entire

TV setup.

Remote does not operate clone programmer.

Clone menu does not display on TV screen, TLL-

1100A shows error message, or LT2002 LED does not blink.

Wrong Installer Remote.

MPI cable not connected.

TV not turned ON.

(LT2002 only) Weak batteries.

(TLL-1100A only) No charge.

Clone menu hard to read.

Weak signal.

No time set.

Time not available.

Clone not working.

Clone programmer problem.

Clone should only scan channels once.

Possible Solution(s)

TLL-1100A: Turn the TLL-1100A OFF and then ON.

LT2002: Press RESET on clone programmer.

Then redo Learn/Teach. (Learning usually takes about 90 seconds;

Teaching usually takes 3 to 4 minutes.)

Only use an LG Installer Remote to operate clone programmer with TV.

Connect MPI cable properly, and ensure good connection.

TV must be turned ON for clone programmer to work.

Install four (4) fresh AA high-quality alkaline batteries.

Ensure the TLL-1100A is fully charged or connected to AC power.

Connect TV to a reliable analog channel signal source.

Set time on a TV, and copy time to clone programmer.

• Try a different clone programmer.

• Reset the clone programmer.

Ensure TV is set up correctly, and try cloning again.

Clone scans channels more than once.

Master and Target TVs

Symptom

Cloning did not work.

(LT2002 only) Clone time disappeared.

New setup not present.

Possible Cause(s)

Procedure interrupted.

Possible Solution(s)

Wait until procedure complete message is displayed.

Different TV models.

Cloning is only possible with identical model TVs.

Step(s) omitted or not performed. Refer to the applicable cloning procedure(s), and make sure all tasks were performed.

Batteries were removed.

Batteries must remain installed to retain time settings.

Target TV not reset.

Disconnect Target TV from AC power for 15 seconds.

• After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.

• If the TV does not display a picture (blank screen) after a few seconds, just change channels.

206-4207

71

Troubleshooting (Cont.)

Channel Banks Setup Troubleshooting

CHANNEL PREVIEW - BANK 1

CH 011-001 NORMAL-ADDED

Enter -> Change

CC -> VCHIP Menu, Ch. Preview -> Exit

Channel Preview/Banks Setup Menu

Symptom

Cannot change channel status in menu.

Channel Preview/Banks

Setup Menu does not appear.

Channel is blanked in all channel banks.

Cannot tune in deleted channel on Channel

Preview/Banks Setup Menu.

“Inactive TV” message appears and then TV turns

OFF.

Channel found during Auto

Tuning does not tune in with

Channel Up/Down.

When BANK on Installer

Remote is pressed, TV shows Input List Menu.

Possible Cause

Channel Access was denied in Express

Script and/or Installer Menu item 028 CH.

OVERIDE is set to 000.

Express Script Installer Menu Wizard/

2-5-5 + MENU (Custom Master TV Setup) not completed/performed.

Possible Solution

Set CH. OVERIDE to 001 to allow access for channel status change.

The Channel Preview/Banks Setup Menu will not be available until the TV setup is transferred to the PTC.

Also, set Installer Menu item 028 CH. OVERIDE to 001 to allow access for channel status changes.

Blanking a channel in one channel bank will make it blank in all channel banks.

Select a channel bank where the deleted channel number is set to NORMAL-ADDED. Direct enter the deleted channel number. Change to the bank in which you want to activate the channel. Select “NORMAL-ADDED” on the

Channel Preview/Banks Setup Menu.

Select another channel bank (1, 2, or 3) to return TV to normal operation.

TV is set up to display “Inactive TV” message if all channels are “NORMAL-

DELETED” from Channel Bank 4.

Channel was deleted in currently selected channel bank.

Installer Menu item 027 HOSPITAL MODE is set to 0.

If banks were set up, premium channels may only be available on another channel bank. Select the channel bank where the channel is set to NORMAL-ADDED. Or, direct enter channel number; then go to Channel Preview/

Banks Setup Menu and select “NORMAL-ADDED.”

Set item 027 to appropriate setting for channel banks to appear with BANK key presses.

72

206-4207

Reference: Glossary of Terms

A list of definitions for some of the words found in this guide

75 OHM RF CABLE

The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV.

300 TO 75 OHM ADAPTER

A small device that connects a 2-wire

300 ohm antenna to a 75 ohm RF jack.

It is usually about an inch long with two screws on one end and a round opening with a wire extending out the other end.

COMPONENT VIDEO

Uses three wires for transporting threecolor video signals. The end result is usually better video quality.

COMPOSITE VIDEO

Typical video jack, uses one wire for transporting three-color video signals.

DELETE

Lets you remove channels from the list that the end user can scroll through using Channel Up/Down.

DIGITAL TELEVISION

High-resolution, cinema-quality television signals transmitted digitally.

A/V CABLES

Audio/Video cables. Three cables bunched together —right audio (red), left audio (white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

DVI

Digital Video Interface. Accommodates analog and digital interfaces with a single connector.

A/V DEVICE

Any device that produces video or sound

(VCR, DVD, cable box, or television).

AMPLIFIER

An electronic device that amplifies sound from a television, CD player, VCR, DVD player, or other audio/video device.

ANALOG TELEVISION

Standard television broadcasting format in 4:3 picture aspect ratio.

ANTENNA

The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna.

CABLE

Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals.

CATV

Programming provided by a cable service.

HDMI

High-definition multi-media interface.

HDSTB

High-definition set-top box. Refers to a tuner device that receives high-definition television signals, which have higher resolution than ordinary analog TV signals.

HDTV

High-definition television. Refers to television signals that have higher resolution than ordinary analog TV signals.

INPUT

Refers to the input jack that receives a signal from a TV, VCR, DVD player or other audio/video device.

JACK

An input or output connector on the back of a TV, VCR, DVD player, or other audio/video device.

MONO SOUND

Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

OUTPUT

Refers to the output jack that sends a signal out of a VCR, DVD player, or other audio/video device.

PHYSICAL CHANNEL NUMBER

The actual channel number. Analog channels use the Physical Channel number, while digital channels can use a

Virtual Channel number.

RGB (RED, GREEN, BLUE)

Connection input or output port available for producing a video image using three separate colors: Red, Green, and Blue.

RS-232

Serial communication port through which firmware is downloaded.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is another, separate audio channel available with some programming. Choosing

SAP often refers to listening to audio in another language, such as Spanish or

French.

SIGNAL

Picture and sound traveling through a cable, or over the air, to the TV.

STEREO SOUND

Stereo (Stereophonic) sound refers to audio that is divided into right and left sides.

TUNER

Device that picks up the broadcast signal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

A re-mapped channel number. Analog channels use the Physical Channel number; however, digital channels use a

Virtual (or false) Channel number.

XDS

Extended Data Service. Additional program information included on the signal provided at the discretion of the broadcaster.

Note: Refer to www.atsc.org for further information.

206-4207

73

Document Revision History / Notes

Document Revision History

Date

February 2012

February 2012

March 2012

Description

Revision A: New document

Revision B: Additional USB port for 26/32LQ630H

Revision C: CQ610H information added

Product documentation is available online at: www.LGsolutions.com/products. From the Products page, select TVs,

Systems & Solutions, then LCD TVs, then the applicable TV. Click the Literature & Downloads tab at the bottom of the TV page, and select the required document(s) from the Downloads list.

Notes

74

206-4207

For Customer Support/Service, please call:

1-888-865-3026

www.LGsolutions.com

Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG

Electronics U.S.A., Inc. b-LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or registered trademarks are the property of their respective owners.

© Copyright 2012, LG Electronics U.S.A., Inc.

206-4207

Revision C

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Table of contents