LG Electronics BE06LU11 Blu

LG Electronics BE06LU11 Blu
External
Blu-ray Disc Rewriter
English
Français Español Português
BE06LU11
CAUTION : The laser used in the External Blu-ray Disc Rewriter can damage your
eyes.
Do not attempt to open the cover.
To reduce the risk of electric shock, do not remove the cover (or back).
There are no user-serviceable parts inside.
Refer servicing to qualified service personnel.
Use of controls or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
WARNING : To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture
Industry Canada requirement
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC COMPLIANCE STATEMENT
Note : This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an Authorized Service Center for help.
• FCC WARNING
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
• This External Blu-ray Disc Rewriter is for use only with UL listed personal computers that have installation instructions detailing userinstallation of card cage accessory.
i
This product is manufactured to comply with the radio interference requirements
of EEC DIRECTIVE 2004/108/EC, 93/68/EEC and 2006/95/EC.
CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO THE BEAM.
ADVARSEL : KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSÆTTELSE FOR STRÅLING.
ADVARSEL : KLASSE 3B SYNLING OG USYNLIG LASERSTRÅLING NÅR
DEKSEL ÅPENS. UNNGÅ EKSPONERING FOR STRÅLEN.
VARNING : KLASSE 3B SYNLING OCH OSYNLIG LASERSTRÅLNING NÄR DENNAL
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO! : KURSSI 3B NÄKYVÄ JA NÄKYMÄTÖN AVATTAESSA OLET
ALTTIINA LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEN.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
CLASE 1
CLASSE 1
■
■
■
■
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
PRODUCTO LÁSER
PRODOTTO LASER
Microsoft® and Windows® are trademarks registered in the United States and other
countries by the Microsoft Corporation.
DVD Logo is a trademark of DVD Format/Logo Licensing Corp., registered in U.S.,
Japan and other countries.
BD Logo is a trademark registered in U.S., Japan and other countries.
The company names and product names written in this manual are trademarks or
registered trademarks of the respective companies.
ii
Contents
Introduction
Features . . . . . . . . . . . . . . . . . .
System requirements . . . . . . . .
Important precautions . . . . . . . .
Location and function of controls
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.2
.3
.4
.5
Installation
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Removing the USB converter cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operation
Loading and ejecting a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Playing a music CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Playing DVD video and MPEG2 movie video . . . . . . . . . . . . . . . . . . . .9
Appendix
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Package contents
Item
Quantity
A. External Blu-ray Disc Rewriter
B. USB 2.0 converter cable
C. AC Power Adapter (with Power supply cable)
D. Software CD
E. BD-RE SL Blank Disc
F. Manual
1
1
1
1
1
1
1
Introduction
Thank you for purchasing the LG External Drive.
Features
•
•
•
•
•
Universal Serial Bus (USB) 2.0 interface
Buffer Under Run error protection technology
Emergency eject support
Bear media loading with power eject.
CD-R/RW, DVD-R/RW/+R/RW/+/-R DL, DVD-RAM, BD-R/RE(SL/DL) read and write
compatible, CD Family, DVD-ROM and BD-ROM read compatible.
Supports region playback control Phase II.
Supports LightScribe Direct Label Printing Technology.
To achieve maximum Record & Write speed your system may require data to be
copied first to the computer’s hard drive rather than directly from another source
disc or drive.
•
•
•
Cautions
System meeting the following requirements is needed in order to use USB 2.0
operation with this drive.
• Computer that is equipped with a USB 2.0 – compliant USB connector or PCI
adapter card, and on which the USB 2.0 EHCI (Enhanced Host Controller
Interface) driver software 1) has been installed.
1)
The USB 2.0 EHCI driver software is supplied with currently available PCI
adapter cards that conform to USB 2.0. Further, Microsoft has released the USB
2.0 EHCI driver software for Windows XP, therefore it is also possible to use this
driver software with Windows XP.
If you want to know in detail, please contact your USB 2.0 adapter dealer or consult
your PC manufacturer, or consult the Microsoft Corporation Web site.
•
Please note: Certain software (i.e. particularly those including Video playback) may
require a considerably increased specification PC to give acceptable results. While
this Blu-ray Disc Rewriter can read DVD-video or BD-MV(BD-ROM) discs,
decoding them to display on your pc’s monitor requires separate MPEG, H.264 or
VC-1 decoding that is done by separate hardware (either an MPEG, H.264 or VC-1
decoder card or MPEG, H.264 or VC-1 decoding done by your video card), or
separate software that you install to do MPEG, H.264 or VC-1 decoding. For further
details, refer to the documentation that comes with MPEG, H.264 or VC-1 software.
2
System requirements
Operating Environment
This unit can be operated in the system environment explained here.
• CPU : Pentium D 3.2 GHz or higher (Recommended Core 2 Duo
E6300 or higher.)
• O/S : Windows XP (Home / Professional / Media Center Edition)
with SP2/ Windows Vista (X86, X64)
• RAM : 1GB or more
• HDD : 30GB or more of available space (60GB for Blu-ray Disc authoring)
Interface
USB 2.0 port
Recommended BD-R : Mitsubishi Kagaku Media, Maxell, TDK.
media
BD-RE : Mitsubishi Kagaku Media, Maxell, Sony, Panasonic.
manufacturer
DVD-R : Maxell, Mitsubishi Kagaku Media, Taiyo.
DVD-RW : JVC, Mitsubishi Kagaku Media.
DVD+R : Mitsubishi Kagaku Media, Verbatim.
DVD+RW : Mitsubishi Kagaku Media, Verbatim.
DVD±R DL : Mitsubishi Kagaku Media, Verbatim.
DVD-RAM : Maxell.
CD-R : LG, Mitsubishi Kagaku Media, Verbatim, Taiyo Yuden TDK.
CD-RW : LG, Ricoh, Mitsubishi Kagaku Media, Verbatim.
System
requirements
* Compatibility problem in write/read function may occur with media depending on the media
manufacturing quality.
* There may be some cases when motion picture playback is not smooth depending on bit rate.
• Playing Blu-ray Movies *NOTICE*
Driver Graphic Card
Interface
Analog
Digital
AACS *1
Compliant
VGA
(D-SUB)
DVI or HDMI
Monitor
HDCP *2
Interface
Not
required
VGA
(D-SUB)
Resolution
1024x768
or more
(Recommended
Compliant DVI or HDMI Compliant : 1920x1080)
HDCP
Not
required
Due to copyright protection features, certain requirements must be met in order to playback BD
movies on a computer. When using digital video connections, the monitor and graphics card must
support High-bandwidth Digital Content Protection (HDCP). Note that most monitors and graphics
cards currently don’t support HDCP. But, most High Definition TVs and multimedia monitors do
support HDCP. Refer to the PC or graphic card maker’s web site to see if your card supports HDCP.
Some video cards that currently support HDCP:
- nVIDIA: GeForce 7800 GTX 512 / 7900 GT / 7900 GX2 / 7900 GTX / 7950 GX2 / 8600 GS / 8600
GT / 8600 GTS / 8800 GTX or higher with 256MB min memory.
- ATI: Radeon® X1950/ HD2300/ HD2400/ HD2600 series or higher with 256MB min memory.
*1
*2
Graphic card driver shall meet AACS compliance criteria. Please consult your graphics card vendor
for proper driver solution.
HDCP (High Bandwidth Digital Content Protection): Required to view pre-recoded Blu-ray Discs
which are copy protected.
3
Important precautions
Follow these precautions when handling the drive or discs.
Precautions
Please note that the manufacturer of this equipment does not offer any warranty
against data loss due to inappropriate installation, handling, direct or indirect
damages. Please note that the manufacturer will bear no responsibility for direct
or indirect damages (including lost data)caused by the use of this product or its
malfunction.
Please backup(copy) all important data as protection against data loss.
Installation
Avoid placing the drive in a location subject to:
- high humidity
- high temperature
- mechanical vibration
- direct sunlight
- excessive dust
Operation
Don’t move the drive suddenly from a cold place to warm one.
Condensation may cause abnormal operation.
Make sure to remove the disc before moving the drive to prevent the possible
damage to the disc.
Prevent foreign objects, such as liquids or metal, from entering the drive and in
the case a foreign object enters the drive, please consult the dealer where the
drive was purchased.
Don’t interrupt the electric power while the drive is operating.
While drive is operating, don’t move the drive or give a shock to the drive, since it
can cause damages to the disc.
Please pay attention to handling Electrostatic Sensitive Devices, you may use
anti-static products such as wrist straps, heel straps, mats to protect your body
from electrostatic.
AC Adapter
Don’t plug in or remove the AC adapter using wet hands.
Don’t damage the AC adapter by scratching, modifying, or bending its prongs.
Use only supplied AC adapter.
Don’t disassemble the AC adapter.
Operation through a USB hub cannot be guaranteed.
When connecting with USB1.1 interface, picture and sound may be disrupted
while watching DVD Video due to lack of data transfer speed.
For smoother playback of DVDs, high-speed USB 2.0 should be used.
4
Location and function of controls
This following is the general figure of the design of the drive. The drive’s
appearance and specifications may change without prior notice.
1
2
3
5
4
6
1. Disc Tray
2. Drive activity indicator
The LED used to indicate the operation of External Blu-ray Disc Rewriter.
3. Emergency Eject Hole
4. Stop/Eject Button
5. USB Connector - This connector is used to connect to the USB
converter cable.
6. Power Connector - This connector is used to connect to the AC Power
adapter cord.
NOTE
•
•
•
•
The machine does not have an ON/OFF switch. As soon as it is connected to the
AC power, the power up sequence begins.
The power supply cord is intended to serve as the main disconnect device. The
power outlet shall be near the equipment and shall be easily accessible.
The appliance is not intended for use by young children or infirm persons without
supervision.
Young Children should be supervised to ensure that they do not play with
appliance.
If the appliance is supplied from a cord extension set or an electrical portable outlet
device, the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.
5
Installation
Hardware Installation
NOTES
Connecting to computer
• Make sure you have a personal
computer with an open USB port before
connecting the drive to your computer.
• Power for all device should be turn off
before attaching the cables.
Connect the drive to the computer as
shown in figure.
1. Connect the USB converter cable to
the External Drive.
To AC wall
outlet.
2. Connect the other end of the USB
converter cable to your computer.
3. Connect the AC adapter plug to the
power connector at the rear of the
drive.
Attach the AC adapter to the AC wall
outlet.
4. When the computer is ready, confirm
that the drive is detected. And then,
insert the supplied software CD into
the External Drive and install the
software.
NOTE
•
Please do not connect the AC adapter and USB 2.0 converter cable by any means
other than specified above.
6
Removing the USB converter cable
The drive supports the plug and play(not swap) function of Windows, and
can be removed and inserted by performing the following operation.
1. Stop the application software being currently used.
2. Click the icon “
side.
” of the taskbar located on your screen’s bottom right
3. Click “Safely Remove USB Mass Storage Device-Drive[x:]”.
4. Click “Ok” and then remove the USB converter cable.
NOTE
Don’t remove the USB converter cable when the busy indicator on the drive
blinks, or during computer startup.
7
Operation
Loading and ejecting a disc
Remember - AC adapter must be connected.
Make sure the power is turned on.
Loading a disc
1. Touch the Eject Button to open the Disc tray.
2. Load a disc. (Label facing up.)
3. Close the Disc tray.
Ejecting a disc
1. Touch the Eject Button to open the Disc tray.
2. Removing the disc.
3. Close the Disc tray after removing the disc.
Emergency Eject
This drive has a feature that allows the CD to be ejected manually in case of
a drive failure or a power outage.
NOTE: Don’t use this feature except in an emergency.
1) Turn the power OFF.
2) Poke a fine-tipped object (such as a straightened heavy duty paper clip)
into the small hole above the eject button. The front door will pop open
and the disk tray will come partway out.
3) Pull the front door to open it all the way, then grip the disc tray between
thumb and forefinger and gently pull it straight out.
NOTE: Use this feature for an
emergency purpose only.
Using it excessively will cause
malfunction.
* If you cannot get a good grip on the disc tray with your fingers, use a steel
binder clip or spring clamp to pull it out.
8
Playing a music CD
Listening to sound
When connected to a computer, you can play audio CD’s through your
computer’s audio system after setting Digital Audio mode.
Check your Windows or “Windows Media Player” manual for detail.
Playing DVD video and MPEG2 movie video
The drive must be connected to a computer, and basic installation already
done. Install the ‘PowerDVD’ software to your PC.
Inserting the disc will automatically start installation. Follow the wizard.
After installation, remove the PowerDVD software and put it away for
safekeeping.
Inserting a DVD Video disc into the drive and it will play automatically.
NOTES
• DVD video region code:
Each region around the world has a different region number on the DVD
video movies being sold in a region.
The region code can be changed to other regions up to 5 times by using
the software decoder (PowerDVD).
If you change the region code 5 times, the drive will lock onto the last (5th
change) region code, and cannot change the drive to another region code.
This limitation is a requirement as licensees of DVD drive technology.
• When connecting with USB1.1 interface, due to it’s slow transfer time,
picture and sound may be disrupted when trying to view a DVD
movie.
9
Appendix
Troubleshooting
If you are experiencing problems with the drive, verify the following items.
Since the problem may be caused by a device other than the drive, check
other things such as system settings or other software being used, etc.
If you cannot resolve the problem after verifying these items, contact your
dealer or our customer service department.
Problem
Possible Cause
Cannot play a DVD
or CD in the drive or
certain types of discs
cannot be read in the
drive.
1. The disc is not inserted
correctly.
2. The disc is dirty.
3. The pick-up lens is dirty.
4. The disc is scratched or
warped.
5. The disc uses a region
code that cannot be
played on the drive.
1. Reinsert the disc
correctly.
2. Clean the disc surface.
3. Clean the pick-up lens.
4. Change the disc.
Disc tray cannot be
opened
1. AC Plug is not connected
to AC outlet.
1. Connect the AC plug
tightly.
Drive is not detected
by the system.
1. The USB 2.0 converter
cable is not properly
connected.
1.Make sure USB 2.0 converter
cable is connected properly
and re-install the device driver.
Drive will not play
media or certain
types of CD or DVD
media
1. The disc doesn’t match
your system. Is the media
disc the correct format for
the type of system that
you are using.
1. Check the disc format.
(on a PC an ISO 9660 IBM
compatible PC format as
opposed to Apple/Mac HFS
disc or UNIX disc
formats will not function)
2. Virus possibility.
2. Has the Windows DVD-ROM
software driver program
been corrupted by a virus?
Run a Virus Scan program
and repair if possible.
10
Possible Solution
5. Refer to your system
manual for help.
Specifications
Items
General
BD/HD DVD/DVD/CD
Supported Discs *1
Dimenslons (WxHxD)
Wcight
Interface
Host Interface
Read/Write Speed *4
BD-ROM(SL/DL), BD-RE*2(SL/DL), BD-R(SL/DL), DVD-ROM(SL/DL),
DVD-R(SL/DL), DVD-RW, DVD+R(SL/DL), DVD+RW, DVD-RAM*3,
CD-ROM, CD-ROM XA, CD-I, Photo-CD (Single & Multi-Session),
Video CD, CD-Audio Disc, Mixed mode, CD-ROM disc (data and audio),
CD-Extra, CD-Text, CD-R, CD-RW
163 x 50 x 260 mm
About 1.5Kg
USB 2.0
Write :
BD-R (SL/DL) : 2x, 4x, 6x/2x, 4x
BD-R (SL LTH) : 2x
BD-RE (SL/DL) : 2x
DVD-R : 1x, 2x, 4x, 8x, 12x, 16x
DVD-R (DL): 2x, 4x
DVD-RW (SL) : 1x, 2x, 4x, 6x
DVD-RAM : 2x, 3x, 5x
DVD+R : 2.4x, 4x, 8x, 12x, 16x
DVD+R (DL): 2.4x, 4x
DVD+RW (SL) : 2.4x, 4x, 6x, 8x
CD-R : 4x, 8x, 16x, 24x, 32x,
40x
CD-RW : 4x, 10x, 16x, 24x
Read :
BD-ROM (SL/DL) : 6x/4.8x max.
BD-R (SL/DL) : 6x/4.8x max.
BD-RE (SL/DL) : 2x/2x max.
BDMV (AACS Compliant Disc):
4.8x max.
DVD-ROM (SL/DL) : 16x/8x max.
DVD-R (SL/DL) : 12x/8x max.
DVD-RW (SL) : 10x max.
DVD+R (SL/DL) : 12x/8x max.
DVD+RW (SL) : 10x max.
DVD-RAM : 5x max.
DVD-Video (CSS Compliant Disc)
(SL/DL) : 8x max.
CD-R/RW/ROM : 40x max.
CD-DA (DAE) : 40x max.
8cm CD : 10x max.
Video CD : 40x max.
Data transfer rate
*Sustained
BD-ROM : 215.79 Mbits/s (6x max)
DVD-ROM : 22.16 Mbytes/s (16x max)
CD-ROM : 6,000 Kbytes/s (40x max)
Average Access
Time (1/3 Stroke)
BD-ROM : 180ms (typ.), DVD-ROM : 160ms (typ.),
DVD-RAM : 180ms (typ.), CD-ROM : 150ms (typ.)
Buffer capacity
4 Mbytes
100000 Power On Hours
Environmental
Level
MTBF
When operating
When not operating
Temperature: -30 °C to 60 °C Humidity: 10% to 90% R.H.
Electrical
Power
DC 12V/ 3A
Performance
Temperature: 5 °C to 40 °C
Humidity: 15% to 85% R.H.
The disc of the cartridge type is not supported.
*2
BD-RE: The disc of version 1.0 is not supported.
*3
DVD-RAM 12X media: Not supported to write.
*4
There might be some cases when this drive can not satisfy the best performance depending on the conditions
of the disc, the drive, and the recording format.
- The maximum data transfer rate varies according to the performance capabilities of the PC.
- For the sake of periodic improvements, specifications and appearance are subject to change without notice.
- We have taken all possible measures to assure the quality of our products, but we cannot be responsible for
the consequences if defect occurs.
*1
11
Copyright © 2008
LG Electronics U.S.A. Inc.
1000 Sylvan Ave.
Englewood Cliffs NJ 07632
U. S. A.
or http://www.lgusa.com
LG Electronics Canada Inc.
550 MATHESON Blvd. East
Mississauga. Ontario L4Z4G3 Canada
LG Electronics Deutschland GMBH
Jakob-Kaiser-Straße 12,
D-47877 Willich, Germany
LG Electronics U. K. Ltd.
LG House, 250 Bath Road,
Slough Berkshire SL1 4DX
United Kingdom
Goldstar France E.U.R.L
Paris Nord II 22, Avenue des
Nations-B.P.50372 VILLEPINTE
95945 ROISSY CDG CEDEX France
LG Electronics Italia S.P.A.
Centro Direzione “IL Quadrate” Via
Modigliani, 20090 Segrate (MI) Italy
LG Electronics España
Complejo Europa Empressaries
(Edif.Bruselas) Ctra. N-VI 28230 Las
Rozas Madrid Spain
LG Electronics Australia Pty Ltd.
2 Wonderland drive, Eastern creek,
NSW 2766
or http://www.lge.com.au
LG Electronics Portugal S.A.
Quinta da Fonte – Edifício D. Amélia
Rua Vítor Câmara, nº2, Piso 2
2700-229 Paço d´ Arcos, Portugal
ou www.lge.pt
Caution!
The disc rotates at high speed in the drive unit.
Use of worn, damaged, or non-standard discs can
adversely affect the drive and cause the disc to
shatter or crush while in use.
Disc crush can only occur when you use a damaged
disc in the drive. It is an extremely rare occurrence,
but there are steps which can be taken to prevent it.
Always check your discs before inserting them
into the drive.
1. Take care not to use worn, cracked, damaged,
warped or poor quality discs, as this may
cause damage to your drive.
2. Check the clear plastic on the center of the
disc, cracks here are the main cause of disc
crush.
3. Do not play discs which are a non-standard
(I.e. non-circular)shape, such as heart shaped
discs, or discs in the shape of a business
card.
How can you keep your discs from becoming
damaged?
1. When not in use, remove discs from the drive.
2. Keep discs in the packaging supplied with
them and out of direct sunlight and away from
heat sources.
Excessive vibration or a sudden jolt to the drive
during operation may cause a malfunction.
Avoid exposing the drive to sudden changes in
temperature as it may cause condensation to collect
inside the drive.
Please visit www.lgservice.com and install the automatic firmware
download program, “LG ODD Online F/W update.” This program
will automatically check for new firmware releases and download
them. It is also included on the software discs that accompany our
drives.
©2008
P/NO. 3828HM1055Nr. A
Made by
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement