Liebert IS-WEBRT3 Network Card User Manual
Add to my manualsLiebert el:Network Card IS-WEBRT3 is a powerful tool that enables you to remotely monitor and control your Liebert equipment. With this card, you can: • Access your equipment's status information from anywhere on your network • Control your equipment's settings remotely • Configure SNMP settings to integrate the card into your existing SNMP implementation • Utilize Liebert MultiLink™ software to automatically shut down your computer system in response to utility power failure • Manage alarm notifications centrally with Liebert Nform
advertisement
Liebert
®
IS-WEBRT3 Card
™
Quick Start Guide
I
NSTALL
• Locate the Liebert IntelliSlot bay on your Liebert equipment. You might need to remove a plastic cover.
• Insert the Liebert IS-WEBRT3 Card into the bay.
• Secure the card with the supplied screws.
• Connect the card to your network with a CAT5 Ethernet cable.
S
ET
L
IEBERT
IS-WEBRT3 C
ARD
P
ASSWORD
• Insert the Liebert PSI-RT3 Software CD and install Liebert DeskPro-Net Utility on your computer.
• Start Liebert DeskPro-Net Utility by clicking on
Start>Programs>NetAgent>DeskPro-Net Utility. The software will automatically find and list available Liebert IS-WEBRT3 cards.
• Double-click on a card in the list to launch it.
• Enter an Account (login name) and Password—Record the login and
password and save them in a safe place.
Control functions
Liebert
IS-WEBRT3 cards found
C
ONFIGURE
L
IEBERT
IS-WEBRT3 C
ARD
• Highlight the card in the list and click Configure to change the card’s IP address, subnet mask, and gateway settings (see your network administrator for the settings).
TheLiebert IS-WEBRT3 card can be used with DHCP or BOOTP, where the system assigns an address, but this makes troubleshooting difficult.
™
• Liebert MultiLink will communicate with the Liebert IS-WEBRT3 card. The software can be configured to shut down a computer system in response to utility power failure and the UPS’ battery backup time.
User Manual
This Quick Start Guide is designed to give you the information you need to install and configure the Liebert IS-
WEBRT3 Card. A full user manual,
SL-52665, is available online at www.liebert.com
. Liebertrecommends that new users consult the user manual.
Web Support
The IS-WEBRT3 Card delivers Web management and control to Liebert equipment. All users on your network will be able to view status information.
Control and configuration capabilities are protected by a username and password combination.
You can change the password from the
Web or from DeskPro-Net Utility.
™
Liebert MultiLink Support
Liebert MultiLink software, can be downloaded at multilink.liebert.com
SNMP Support
The Liebert IS-WEBRT3 Card enables
SNMP management of Liebert PSI equipment. To integrate the card into your SNMP implementation, you will need to compile the UPS MIB on your network management station (NMS).
The UPS MIB is included in this package on CD-ROM and supports both
Windows and Unix file formats.
Liebert Nform Support
Utilizing the SNMP and Web technologies built into each of the
Intellislot Web cards, Liebert Nform will centrally manage alarm notifications to provide you with an easy interface to access critical system information.
A downloadable edition is available online at nform.liebert.com
Technical Support/Service
Web Site www.liebert.com
Monitoring
800-222-5877 [email protected]
Outside the US: 614-841-6755
Locations
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
SL-52660_REV01_07-08
Locations
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
7/F, Dah Sing Financial Centre
108 Gloucester Road, Wanchai
Hong Kong
852 25722201
Fax: 852 28029250
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project